TE100-P21/TEW-P21G Windows 7 Installation Instruction
Hardware Installation
your desktop.
2. Right click on the file and select Extract All. Follow the wizard to uncompress the file.
3. Connect a RJ-45 Network cable from a switch/router to the LAN port of the Print Server
4. Connect the detachable antenna (for TEW-P21G only)
5. Connect the AC power adapter to the Print Server and then to a power outlet
6. Connect the Printer to the USB or parallel port on the Print Server
7. Power on the Printer
Configure the Print Server
1. Double click on PSUtilitySetup_v3.13.exe
2. Follow the steps to configure the Print server
a. Select the Print Server and
click Change IP Address.
Manually assign the IP
Address of the Print
Server and then click OK.
Note: The IP Address must
match the network
segment of your network.
b. Click OK
Download from Www.Somanuals.com. All Manuals Search And Download.
Add the Printer to your computer
1. Double click on PSWizardSetup_v2.20.exe
2. Follow the steps to add the printer to your computer
a. Select the print server, select
the desired port and then click
Add Printer.
Note:
1. If your printer is connect to
USB1, select
PS-XXXXXX-U1. If your
printer is connected to
USB2, select
PS-XXXXXX-U2. If your
printer is connected to
LPT, select
PS-XXXXXX-P3.
2. PS-XXXXXX represents
the Server Name of your
print server. Your print
server will have a different
Server Name.
b. Click Select from
manufacturer list.
Select the
appropriate driver for
your printer and then
click Next.
Download from Www.Somanuals.com. All Manuals Search And Download.
c. Click Next.
d. Click Print Test Page.
e. Click OK.
Download from Www.Somanuals.com. All Manuals Search And Download.
f. Click Finish.
g. Repeat the above steps to add the
printer to other computers on the
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
The PS Wizard / PS Utility is unable to see my printer server. What should I do?
1. Double check your hardware connections; make sure that the print server and printer are powered ON
and are properly connected.
2. Click Discover.
3. Disable any software firewall programs (e.g. ZoneAlarm). Also, disable the built in Windows firewall
program.
My printer does not print the entire document. What should I do?
Windows 7
1. Click on the Windows icon on the bottom left-hand corner of the screen.
2. Click Devices and Printers.
3. Right click on the printer and select Printer Properties.
4. Click the Advanced tab.
5. Uncheck Enable advanced printing features.
6. Click Apply.
7. Click OK.
I successfully added a printer to my computer and I can print a test page, but I cannot print anything from
Microsoft Word or other applications.
Make sure the printer is set as your default printer. Click the Windows icon -> Devices and Printers and verify
that your printer icon has a check on it.
I configured my print server to automatically receive an IP Address from a DHCP server, and now I cannot go
into the Print Server’s web utility.
Open PS Wizard (See Add the Printer to your PC) to locate your print server’s IP Address.
After I successfully configured the TEW-P21G to match my wireless network settings, I can not print through
the Print Server.
1. Verify that the wireless settings match your wireless network settings.
2. Verify that the antenna is attached to the Print Server and the WLAN LED on the Print Server is lit.
I forgot the administration password. How do I reset my print server?
Factory reset the print server using the following procedure. This procedure will reset all settings to default.
By default, there is no password.
1. Take a pin or paper clip and press the reset button. The reset button is located on the back of the unit.
2. Wait 15 seconds, then let go.
Download from Www.Somanuals.com. All Manuals Search And Download.
|