Download from Www.Somanuals.com. All Manuals Search And Download.
-
-
-
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
-
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. End users must follow the specific operating instructions
for satisfying RF exposure compliance. To maintain compliance with FCC RF
exposure compliance requirements, please follow operation instruction as
documented in this manual.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
SAR compliance has been established in typical laptop computer(s) with CardBus
slot, and product could be used in typical laptop computer with CardBus slot. Other
application like handheld PC or similar device has not been verified and may not
compliance with related RF exposure rule and such use shall be prohibited.
The availability of some specific channels and/or operational frequency bands are
country dependent and are firmware programmed at the factory to match the
intended destination. The firmware setting is not accessible by the end user.
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
Europe – EU Declaration of Conformity
This device complies with the essential requirements of the R&TTE Directive
1999/5/EC. The following test methods have been applied in order to prove
presumption of conformity with the essential requirements of the R&TTE Directive
1999/5/EC:
EN 60 950-1: 2001 +A11: 2004
Safety of Information Technology Equipment
EN 50392: 2004
Generic standard to demonstrate the compliance of electronic and electrical
apparatus with the basic restrictions related to human exposure to electromagnetic
fields (0 Hz - 300 GHz)
EN 300 328 V1.6.1 (2004-11)
Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband
transmission systems; Data transmission equipment operating in the 2,4 GHz ISM
band and using wide band modulation techniques; Harmonized EN covering
essential requirements under article 3.2 of the R&TTE Directive
EN 301 489-17 V1.6.1 (2005-08) and EN 301 489-1 V1.4.1 (2002-08)
Electromagnetic compatibility and Radio spectrum Matters (ERM);
ElectroMagnetic Compatibility (EMC) standard for radio equipment and services;
Part 17: Specific conditions for 2,4 GHz wideband transmission systems and 5 GHz
high performance RLAN equipment
This device is a 2.4 GHz wideband transmission system (transceiver), intended for
use in all EU member states and EFTA countries, except in France and Italy where
restrictive use applies.
In Italy the end-user should apply for a license at the national spectrum authorities
in order to obtain authorization to use the device for setting up outdoor radio links
and/or for supplying public access to telecommunications and/or network services.
This device may not be used for setting up outdoor radio links in France and in
some areas the RF output power may be limited to 10 mW EIRP in the frequency
range of 2454 – 2483.5 MHz. For detailed information the end-user should contact
the national spectrum authority in France.
0560
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Česky TRENDnet tímto prohlašuje, že tento TEW-623PI je ve shodě se základními požadavky a
[Czech]
dalšími příslušnými ustanoveními směrnice 1999/5/ES.
Dansk Undertegnede TRENDnet erklærer herved, at følgende udstyr TEW-623PI overholder de
[Danish]
væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Deutsch Hiermit erklärt TRENDnet, dass sich das Gerät TEW-623PI in Übereinstimmung mit den
[German]
grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie
1999/5/EG befindet.
Eesti Käesolevaga kinnitab TRENDnet seadme TEW-623PI vastavust direktiivi 1999/5/EÜ
[Estonian]
põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.
English
Hereby, TRENDnet, declares that this TEW-623PI is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
Español Por medio de la presente TRENDnet declara que el TEW-623PI cumple con los requisitos
[Spanish]
esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
Ελληνική ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ TRENDnet ΔΗΛΩΝΕΙ ΟΤΙ TEW-623PI ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ
[Greek]
ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ
1999/5/ΕΚ.
Français Par la présente TRENDnet déclare que l'appareil TEW-63PI est conforme aux exigences
[French]
essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.
Italiano Con la presente TRENDnet dichiara che questo TEW-623PI è conforme ai requisiti essenziali ed
[Italian]
alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Latviski Ar šo TRENDnet deklarē, ka TEW-623PI atbilst Direktīvas 1999/5/EK būtiskajām prasībām un
[Latvian]
citiem ar to saistītajiem noteikumiem.
Lietuvių Šiuo TRENDnet deklaruoja, kad šis TEW-623PI atitinka esminius reikalavimus ir kitas
[Lithuanian]
1999/5/EB Direktyvos nuostatas.
Nederlands Hierbij verklaart TRENDnet dat het toestel TEW-623PI in overeenstemming is met de essentiële
[Dutch]
eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.
Malti Hawnhekk, TRENDnet jiddikjara li dan TEW-623PI jikkonforma mal-ħtiġijiet essenzjali u ma
[Maltese]
provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.
Magyar Alulírott, TRENDnet nyilatkozom, hogy TEW-623PI megfelel a vonatkozó alapvetõ
[Hungarian]
követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.
Polski Niniejszym TRENDnet oświadcza, że TEW-623PI jest zgodny z zasadniczymi wymogami oraz
[Polish]
pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.
Português TRENDnet declara que este TEW-623PI está conforme com os requisitos essenciais e outras
[Portuguese]
disposições da Directiva 1999/5/CE.
Slovensko TRENDnet izjavlja, da je ta TEW-623PI v skladu z bistvenimi zahtevami in ostalimi
[Slovenian]
relevantnimi določili direktive 1999/5/ES.
Slovensky TRENDnet týmto vyhlasuje, že TEW-623PI spĺňa základné požiadavky a všetky príslušné
[Slovak]
ustanovenia Smernice 1999/5/ES.
Suomi TRENDnet vakuuttaa täten että TEW-623PI tyyppinen laite on direktiivin 1999/5/EY oleellisten
[Finnish]
vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.
Svenska Härmed intygar TRENDnet att denna TEW-623PI står I överensstämmelse med de väsentliga
[Swedish]
egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.
Export restrictions
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
This product or software contains encryption code that may not be exported or
transferred from the US of Canada without an approved US Department of
Commerce export license.
Safety Information
Your device contains a low power transmitter. When device is transmitted it sends
out radio frequency (RF) signal.
CAUTION: To maintain compliance with FCC’s RF exposure guidelines, this
equipment should be installed and operated with minimum distance 20cm between
the radiator and your body. Use on the supplied antenna. Unauthorized antenna,
modification, or attachments could damage the transmitter and may violate FCC
regulations.
The antenna(s) used for this transmitter must be installed to provide a separation
distance of at least 20 cm from all persons and must not be co-located or operating
in conjunction with any other antenna or transmitter.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
Protection requirements for health and safety – Article 3.1a
Testing for electric safety according to EN 60950 has been conducted. These are
considered relevant and sufficient.
Protection requirements for electromagnetic compatibility – Article
3.1b
Testing for electromagnetic compatibility according to EN 301 489-1, EN 301 489-
17 and EN 55024 has been conducted. These are considered relevant and sufficient.
Effective use of the radio spectrum – Article 3.2
Testing for radio test suites according to EN 300 328-2 has been conducted. These
are considered relevant and sufficient.
CE in which Countries where the product may be used freely:
Germany, UK, Italy, Spain, Belgium, Netherlands, Portugal, Greece, Ireland,
Denmark, Luxembourg, Austria, Finland, Sweden, Norway and Iceland.
France: except the channel 10 through 13, law prohibits the use of other channels.
v
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENT
Introduction ................................................................................................ 1
Overview of this User’s Guide............................................................................... 1
Unpacking and Setup.................................................................................. 2
Unpacking .............................................................................................................. 2
Setup....................................................................................................................... 2
Hardware Installation ................................................................................. 3
LED Indicator for CardBus .................................................................................... 3
LED Indicator for PCI............................................................................................ 3
Check the installation ............................................................................................. 3
Software Installation................................................................................... 4
Windows Utility and Driver Installation ................................................................ 4
Windows Wireless Utility Setting .......................................................................... 5
Technical Specifications....................................................................................... 17
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Congratulations on your purchase of this 300Mbps 802.11n Wireless LAN Adapter.
This manual contains detailed instructions regarding the operation of this product.
Please keep this manual for future reference.
With the 300Mbps 802.11n Wireless LAN Adapter, a desktop or laptop computer
can communicate with another computer wirelessly. An easy-to-use utility is
bundled with the 300Mbps 802.11n Wireless LAN Adapter for configuration,
monitoring, and diagnostic purposes.
The 300Mbps 802.11n Wireless LAN Adapter can wirelessly transmit and receive
data, at a speed of up to 300 megabits per second.
The 300Mbps 802.11n Wireless LAN Adapter provides users with access to real-
time information anywhere in their organization. The mobility of the 300Mbps
802.11n Wireless LAN Adapter provides productivity and service, which are not
available under wired networks. The 300Mbps 802.11n Wireless LAN Adapter can
easily adapt from peer-to-peer networks, suitable for a small number of users, to
full infrastructure networks of thousands of users that allow roaming around a
broad area.
Overview of this User’s Guide
Introduction. Describes the 300Mbps 802.11n Wireless LAN Adapter and its
features.
Unpacking and Setup. Helps you get started with the basic installation of the
300Mbps 802.11n Wireless LAN Adapter.
Hardware Installation. Describes the LED indicator on the Adapter.
Software Installation. Describes how to setup the driver and the utility setting.
Technical Specifications. Lists the technical (general, physical and environmental)
specifications of the 300Mbps 802.11n Wireless LAN Adapter.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
UNPACKING AND SETUP
This section provides unpacking and setup information for the 300Mbps 802.11n
Wireless LAN Adapter.
Unpacking
The box should contain the following items:
TEW-623PI PCI Adapter
CD-ROM (Utility/Driver and User’s Guide)
Multi-Language Quick Installation Guide
If any item is found missing or damaged, please contact your local reseller for
replacement.
Setup
Before installation, check the following:
z Make sure your computer is running at least a 300MHz or above processor with
256MB RAM or above
z Visually inspect the CardBus/PCI Adapter and make sure that it is fully plugged
in to the CardBus/PCI slot.
z The operating system on your computer must be the following: Windows 7.
Vista, XP (Service Pack 2) or 2000 (Service Pack 4)
z A 802.11n or 802.11b/g access point or router.
z Make sure the environment has minimal interference and obstructions.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE INSTALLATION
LED Indicator for CardBus
Link
The Link LED indicator lighted green when the 300Mbps Wireless N PCI Adapter
is connected to wireless network successfully.
ACT (Activity)
The ACT LED indicator blinking green when the 300Mbps Wireless N PCI
Adapter is transmitting or receiving data.
LED Indicator for PCI
Link
The Link LED indicator lighted green when the 300Mbps 802.11g Wireless LAN
Adapter is connected to wireless network successfully.
Check the installation
The LEDs of the Wireless LAN Adapter are clearly visible and the status of the
network link can be seen instantly:
1. Once the device is plugged to the station’s PCI slot, the LED of the Wireless
LAN Adapter will light up indicating a normal status.
2. When the device plugged to the station’s PCI slot and the driver was installed,
the ACT will start alternate blinking, it means that the device is starting to scan
the wireless devices near the Wireless LAN Adapter.
3. While the Wireless LAN Adapter linked up and transmitting data to the Access
Point or to other Wireless LAN station, the Link LED will lighted green.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SOFTWARE INSTALLATION
This section describes how to install the driver and utility for the 300Mbps Wireless
N PCI Adapter.
Note: DO NOT install the 300Mbps 802.11g Wireless LAN Adapter in the
computer until instructed to do so.
Windows Utility and Driver Installation
1) Insert the CD-ROM into your CD-ROM drive, the Autorun will appear.
2) Click “Install Utility & Driver” icon to install the driver and software and the
install wizard will begin installing the software. Follow the install wizard
instructions to complete the installation.
3) Follow the Install Shield Wizard Instructions. Click “Next” to continue and
finish it.
4) Once the utility is installed, turn off the PC, open the cover and install the
TEW-623PI adapter to the available PCI slot. Attach the antennas, close the
cover and boot up the PC again. The windows will detect new hardware and
install the appropriate driver automatically.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
When the Wireless LAN Adapter was installed, you will see the icon on the
Windows task bar. The user can configure the wireless settings using the Wireless
Adapter Configuration Utility. Double-click the utility icon that appears in the
taskbar
When the icon in the toolbar represents in full green color then the signal strength
has an excellent performance with the AP, if it represents in yellow color then the
signal strength has a fair performance with the AP, and if the icon represents no
color, then the signal strength has a worst performance with the wireless station.
Windows Wireless Utility Setting
The user can configure the wireless settings using the Wireless Adapter
Configuration Utility. Double-click the utility icon that appears in the taskbar.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Link Information
This is the default screen after launching the Utility program.
Status: Shows the associated BSSID, which can be used to identify the wireless
access point.
SSID: Shows the current SSID, which must be the same on the wireless client and
AP in order for communication to be established.
Wireless Mode: Shows the current wireless mode used for wireless communication.
Encryption: Shows the current encryption mode used on the wireless network.
TxRate: Shows the current data rate used for transmitting.
Channel: Shows the current channel for communication.
Signal Strength of Percentage: Shows the wireless signal strength of the
connection between the Wireless LAN Adapter with the Access Point.
Tx/Rx: Shows the statistics of data transfer, and the calculation is based on the
number of packets transmitted and received. It also shows the link quality of the
Wireless LAN Adapter with the Access Point when operating under Infrastructure
mode.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuration
This screen is where you set the basic wireless settings for the Wireless LAN
Adapter
SSID: Service Set Identifier, which is a unique name shared among all clients in a
wireless network. The SSID must be identical for each client in the wireless
network.
Wireless Mode: There are two modes available for selection
● Infrastructure – to establish wireless communication with the LAN and other
wireless clients through the use of Access Points.
● Ad-Hoc – to establish point-to-point wireless communication directly with
other wireless client devices.
Authentication: The following options are available: Open System, Shared Key,
WPAPSK, WPA2-PSK, WPA EAP-TLS, WPA2 EPA-TLS and WPA2-PSK.
Select Open System, Shared Key for WEP data encryption feature.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Open or Shared Key
Open System and Shared Key require the user to set a WEP key to exchange
data with other wireless clients that have the same WEP key.
z Default Key: select one of the 4 keys to use.
z Network Key: choose the encryption way, either in HEX or ASCII formats,
and enter the password in the blank space.
z Key Length: select 64 or 128 bits as the length of the keys
Key Format: HEX or ASCII
WPA-PSK/WPA2-PSK
If WPA-PSK/WPA2-PSK is selected the below window appears. Please enter a
WPA Passphrase.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
WPA-PSK/WPA2-PSK
If WPA/WPA2 is selected, configuration is enabled. Please click the
“configuration” button. Select a certification for drop down list.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Site Survey
This screen allows the user to scan for available wireless networks (wireless clients
and Access Points). It also allows the user to establish wireless communications
with an available wireless network.
Available Network – displays the wireless networks (wireless clients and access
points) that are within range.
Select any one of the wireless networks by double-clicking on it or clicking on the
“Connect” button.
Click the “Refresh” button to scan for available networks.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Profile
Profile – The user can create and manage the created profiles for home, work or
public areas. By double-clicking on one of the created profile, the setting will adjust
to the specific setting such as SSID, channel, and encryption as saved by that
particular profile.
Remove: Deletes the selected profile
Add: Adds a profile. The following screen will appear. The user can enter the
necessary information required for accessing Access Points or Wireless Router
Connect: The current connected profile information.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
WPS
Wi-Fi Protected Setup (WPS) is an optional certification program from the Wi-Fi
Alliance that is designed to ease the task of setting up and configuring security on a
wireless network. There are two methods used in the WPS as below instruction.
Push the button on my access point
Using the WPS configuration with the “Push the button on my access point”
method, the configuration steps as below:
1) Selected the “Push the button on my access point”.
2) Push the WPS configuration button on your wireless access point or router.
3) Click the Next button start the WPS configuration.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
4) If the WPS configuration was successful, the follow window will appear.
5) If the WPS configuration failed, the follow window will appear.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Enter a PIN into my access point
Using the WPS configuration with the “Enter a PIN into my access point” method,
the configuration steps as below:
1) Selected the “Enter a PIN into my access point”, the PIN will be show on the
button of the windows.
2) Enter the PIN code into the WPS “Clint PIN number” of you wireless access
point or router then click the Start PIN button, the wireless access point or
router will start the WPS configuration process.
3) Selected a wireless access point or router which one will be connecting then
click the Next button start the WPS configuration. If the “Automatically select
the network” was checked, the setup step will be skip.
Download from Www.Somanuals.com. All Manuals Search And Download.
4) If the WPS configuration was successful, the follow window will appear.
5) If the WPS configuration failed, the follow window will appear.
Download from Www.Somanuals.com. All Manuals Search And Download.
About
This screen displays information about the Wireless LAN Adapter, such as the
Driver and Utility version. When a new version of the utility becomes available for
upgrade, users will be able to identify by version numbers.
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Specifications
General
IEEE 802.11b Direct Sequence Spread Spectrum (DSSS)
Radio Technology
IEEE 802.11g Orthogonal Frequency Division Multiplexing (OFDM)
IEEE 802.11n Orthogonal Frequency Division Multiplexing (OFDM)
Interface
PC Card: 32‐bit CardBus, PCI Adapter: 32‐bit PCI bus
Data Transfer Rate
802.11b: up to 11Mbps
802.11g: up to 54Mbps
802.11n: up to 300Mbps
300Mbps: Typical ‐65dBm @ 10% PER (Packet Error Rate)
54Mbps: Typical ‐72dBm @ 10% PER (Packet Error Rate)
11Mbps: Typical ‐86dBm @ 8% PER (Packet Error Rate)
Receiver Sensitivity
Transmit Power
802.11b: 17dBm
802.11g: 14dBm
802.11n: 13dBm
2412 ~ 2484 MHz ISM band (channels 1 ~ 13)
2400~2483.5MHz ISM band (channels 1 ~ 11)
Frequency Range
Modulation Schemes
Channels
DBPSK/DQPSK/CCK/OFDM
1~11 channels (FCC), 1~13 channels (ETSI)
Media Access Protocol
CSMA/CA with ACK
Security
64/128‐bits WEP Encryption, WPA‐PSK/WPA2‐PSK, WPA/WPA2‐RADIUS
PC Card: Link, ACT
PCI Adapter: Link
Diagnostic LED
PC Card: Integrated printed dual diversity antennas
PCI: 3 x 2dBi dipole antenna
Antenna
Download from Www.Somanuals.com. All Manuals Search And Download.
Physical and Environmental
Driver Support
Temperature
Humidity
Windows 7 (32/64‐bit), Vista (32/64‐bit), XP (32/64‐bit), 2000
Operating: 0° ~ 40° C, Storage: ‐10° ~ 70° C
10% ~ 95% RH, no condensation
Dimensions
Certifications
PC Card:, 115 x 54 x 8.7 mm, PCI Adapter: 13 x 121 x 21.6
CE, FCC
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited Warranty
TRENDnet warrants its products against defects in material and workmanship, under normal
use and service, for the following lengths of time from the date of purchase.
TEW‐623PI – 3 Years Warranty
AC/DC Power Adapter, Cooling Fan, and Power Supply carry 1 year warranty.
If a product does not operate as warranted during the applicable warranty period, TRENDnet
shall reserve the right, at its expense, to repair or replace the defective product or part and
deliver an equivalent product or part to the customer. The repair/replacement unit’s warranty
continues from the original date of purchase. All products that are replaced become the
property of TRENDnet. Replacement products may be new or reconditioned. TRENDnet does
not issue refunds or credit. Please contact the point‐of‐purchase for their return policies.
TRENDnet shall not be responsible for any software, firmware, information, or memory data
of customer contained in, stored on, or integrated with any products returned to TRENDnet
pursuant to any warranty.
There are no user serviceable parts inside the product. Do not remove or attempt to service
the product by any unauthorized service center. This warranty is voided if (i) the product has
been modified or repaired by any unauthorized service center, (ii) the product was subject to
accident, abuse, or improper use (iii) the product was subject to conditions more severe than
those specified in the manual.
Warranty service may be obtained by contacting TRENDnet within the applicable warranty
period and providing a copy of the dated proof of the purchase. Upon proper submission of
required documentation a Return Material Authorization (RMA) number will be issued. An
RMA number is required in order to initiate warranty service support for all TRENDnet
products. Products that are sent to TRENDnet for RMA service must have the RMA number
marked on the outside of return packages and sent to TRENDnet prepaid, insured and
packaged appropriately for safe shipment. Customers shipping from outside of the USA and
Canada are responsible for return shipping fees. Customers shipping from outside of the USA
are responsible for custom charges, including but not limited to, duty, tax, and other fees.
WARRANTIES EXCLUSIVE: IF THE TRENDNET PRODUCT DOES NOT OPERATE AS WARRANTED
ABOVE, THE CUSTOMER’S SOLE REMEDY SHALL BE, AT TRENDNET’S OPTION, REPAIR OR
REPLACE. THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF
ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW,
STATUTORY OR OTHERWISE, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE. TRENDNET NEITHER ASSUMES NOR AUTHORIZES ANY OTHER
Download from Www.Somanuals.com. All Manuals Search And Download.
PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE,
INSTALLATION MAINTENANCE OR USE OF TRENDNET’S PRODUCTS.
TRENDNET SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION
DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY
CUSTOMER’S OR ANY THIRD PERSON’S MISUSE, NEGLECT, IMPROPER INSTALLATION OR
TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR OR MODIFY, OR ANY OTHER CAUSE BEYOND
THE RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, OR OTHER HAZARD.
LIMITATION OF LIABILITY: TO THE FULL EXTENT ALLOWED BY LAW TRENDNET ALSO EXCLUDES
FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY, WHETHER BASED IN CONTRACT OR TORT
(INCLUDING NEGLIGENCE), FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR
PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS,
LOSS OF INFORMATION OR DATE, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN
CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE,
OR INTERRUPTION OF THE POSSIBILITY OF SUCH DAMAGES, AND LIMITS ITS LIABILITY TO
REPAIR, REPLACEMENT, OR REFUND OF THE PURCHASE PRICE PAID, AT TRENDNET’S OPTION.
THIS DISCLAIMER OF LIABILITY FOR DAMAGES WILL NOT BE AFFECTED IF ANY REMEDY
PROVIDED HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE.
Governing Law: This Limited Warranty shall be governed by the laws of the state of California.
Some TRENDnet products include software code written by third party developers. These
codes are subject to the GNU General Public License ("GPL") or GNU Lesser General Public
License ("LGPL").
for the desired TRENDnet product to access to the GPL Code or LGPL Code. These codes are
distributed WITHOUT WARRANTY and are subject to the copyrights of the developers.
TRENDnet does not provide technical support for these codes. Please go to
http://www.gnu.org/licenses/gpl.txt or http://www.gnu.org/licenses/lgpl.txt for specific terms of each license.
PWP05202009v2
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|