TD-8817
ADSL2+ Ethernet/USB Modem Router
Rev: 3.0.0
1910010897
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may
cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам
нормативних документів та вимогам, що передбачені чинними законодавчими актами
України.
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Information
When product has power button, the power button is one of the way to shut off the product;
when there is no power button, the only way to completely shut off power is to disconnect the
product or the power adapter from the power source.
Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock
and voiding the limited warranty. If you need service, please contact us.
Avoid water and wet locations.
This product can be used in the following countries:
AT
ES
LT
BG
FI
BY
FR
MT
SK
CA
GB
NL
TR
CZ
GR
NO
UA
DE
HU
PL
DK
IE
EE
IT
LV
SE
PT
RO
RU
Download from Www.Somanuals.com. All Manuals Search And Download.
TP-LINK TECHNOLOGIES CO., LTD
DECLARATION OF CONFORMITY
For the following equipment:
Product Description: ADSL2+ Ethernet/USB Modem Router
Model No.: TD-8817
Trademark: TP-LINK
We declare under our own responsibility that the above products satisfy all the technical
regulations applicable to the product within the scope of Council Directives:
Directives 2004 / 108 / EC, Directives 2006 / 95 / EC, Directives 2011/65/EU
The above product is in conformity with the following standards or other normative documents：
EN 55022:2010
EN 55024:2010
EN 61000-3-2:2006+A1:2009+A2:2009
EN 61000-3-3:2008
EN 60950-1:2006+A11：2009+A1:2010+A12:2011
The product carries the CE Mark
Person responsible for marking this declaration:
Yang Hongliang
Product Manager of International Business
Date of issue: 2013
TP-LINK TECHNOLOGIES CO., LTD.
Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park,
Shennan Rd, Nanshan, Shenzhen, China
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Chapter 1. Introduction ........................................................................................ 2
1.1 Product Overview...................................................................................................... 2
1.2 Main Features ........................................................................................................... 2
1.3 Conventions .............................................................................................................. 3
Chapter 2. Hardware Installation......................................................................... 4
2.1 The Front Panel ........................................................................................................ 4
2.2 The Back Panel......................................................................................................... 5
2.3 Installation Environment............................................................................................ 5
2.4 Hardware Installation Procedures............................................................................. 6
Chapter 3. Quick Installation Guide .................................................................... 8
3.1 TCP/IP Configuration ................................................................................................ 8
3.2 USB Configuration .................................................................................................... 9
3.3 Login ....................................................................................................................... 11
Chapter 4. Software Configuration.................................................................... 14
4.1 Status...................................................................................................................... 14
4.1.1 Device Info .....................................................................................................................14
4.1.2 System Log ....................................................................................................................15
4.1.3 Statistics.........................................................................................................................16
4.2 Quick Start .............................................................................................................. 18
4.3 Interface Setup........................................................................................................ 18
4.3.1 Internet ...........................................................................................................................18
4.3.2 LAN.................................................................................................................................28
4.4 Advanced Setup...................................................................................................... 32
4.4.1 Firewall...........................................................................................................................32
4.4.2 Routing...........................................................................................................................32
4.4.3 NAT ................................................................................................................................33
4.4.4 QoS ................................................................................................................................37
4.4.5 VLAN ..............................................................................................................................40
4.4.6 ADSL ..............................................................................................................................42
4.5 Access Management............................................................................................... 43
4.5.1 ACL.................................................................................................................................43
4.5.2 Filter................................................................................................................................44
4.5.3 SNMP.............................................................................................................................50
4.5.4 UPnP..............................................................................................................................50
4.5.5 DDNS .............................................................................................................................51
Download from Www.Somanuals.com. All Manuals Search And Download.
4.5.6 CWMP............................................................................................................................52
4.6 Maintenance............................................................................................................ 52
4.6.1 Administration.................................................................................................................53
4.6.2 Time Zone ......................................................................................................................53
4.6.3 Firmware.........................................................................................................................55
4.6.4 SysRestart......................................................................................................................57
4.6.5 Diagnostics.....................................................................................................................57
4.7 Help......................................................................................................................... 57
Appendix A: Specifications................................................................................... 59
Appendix C: Troubleshooting............................................................................... 64
Appendix D: Technical Support............................................................................ 67
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Package Contents
The following items should be found in your package:
One TD-8817 ADSL2+ Ethernet/USB Modem Router
One Power Adapter for TD-8817 ADSL2+ Ethernet/USB Modem Router
Quick Installation Guide
One RJ45 cable
One USB cable
Two RJ11 cables
One ADSL splitter
One Resource CD , including:
This User Guide
USB Driver
Other Helpful Information
Note:
Make sure that the package contains the above items. If any of the listed items are damaged or
missing, please contact your distributor.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Chapter 1. Introduction
Thank you for choosing the TD-8817 ADSL2+ Ethernet/USB Modem Router.
1.1 Product Overview
The device is designed to provide a simple and cost-effective ADSL Internet connection for a
private Ethernet network.
TD-8817 connects to an Ethernet LAN or computers via standard Ethernet ports. The ADSL
connection is made using ordinary telephone line with standard connectors. Multiple workstations
can be networked and connected to the Internet using a single Wide Area Network (WAN)
interface and single global IP address. The advanced security enhancements, IP/MAC Filter,
Application Filter and URL Filter can help to protect your network from potentially devastating
intrusions by malicious agents from the outside of your network.
Quick Start of the Web-based Utility is supplied and friendly help messages are provided for the
configuration. Network and Router management is done through the Web-based Utility which can
be accessed through local Ethernet using any web browser.
ADSL
TD-8817 supports full-rate ADSL2+ connectivity conforming to the ITU and ANSI specifications. In
addition to the basic DMT physical layer functions, the ADSL2+ PHY supports dual latency
ADSL2+ framing (fast and interleaved) and the I.432 ATM Physical Layer.
1.2 Main Features
1 10/100M RJ-45 LAN ports (Auto MDI/MDIX), one RJ11 port, one USB 1.1 port.
Downstream data rates up to 24Mbps, upstream data rates up to 3.5Mbps (With Annex M
enabled).
Supports long transfers, the max line length can reach to 6.5Km.
Supports remote configuration and management through SNMP and CWMP.
Supports PPPoE, it allows connecting the Internet on demand and disconnecting from the
Internet when idle.
Quick response semi-conductive surge protection circuit, provides reliable ESD and
surge-protect function.
High speed and asymmetrical data transmit mode, provides safe and exclusive bandwidth.
Supports All ADSL industrial standards.
Compatible with all mainstream DSLAM (CO).
Provides integrated access of Internet and route function which face to SOHO user.
Real-time Configuration and device monitoring.
Supports Multiple PVC (Permanent Virtual Circuit).
2
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Built-in DHCP server.
Built-in firewall, supports IP/MAC filter, Application filter and URL filter.
Supports Virtual Server, DMZ host and IP Address Mapping.
Supports Dynamic DNS, UPnP and Static Routing.
Supports system log and flow Statistics.
Supports firmware upgrade and Web management.
1.3 Conventions
The Router or device mentioned in this User Guide stands for TD-8817 without any explanations.
Parameters provided in the pictures are just references for setting up the product, which may
differ from the actual situation.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Chapter 2. Hardware Installation
2.1 The Front Panel
Figure 2-1
The LEDs are located on the front panel, they indicate the device’s working status. For details,
LED Explanation:
Name
Status
Indication
On
The modem router is powered on.
Power
The modem router is off. Please ensure that the power
adapter is connected correctly.
Off
On
There is a device connected to this USB port.
The modem router is sending or receiving data over this
USB port.
USB
LAN
Flash
Off
On
There is no device connected to this USB port.
There is a device connected to this LAN port.
The modem router is sending or receiving data over this
LAN port.
Flash
Off
On
There is no device connected to this LAN port.
ADSL line is synchronized and ready to use.
The ADSL negotiation is in progress.
Flash
ADSL
troubleshooting.
Off
On
The network is available with a successful Internet
connection.
There is data being transmitted or received via the
Internet.
Flash
Internet
There is no successful Internet connection or the modem
router is operating in Bridge mode. Please refer to Note 2
for troubleshooting.
Off
Note:
Installation Procedures for more information about how to make Internet connection
correctly. If you have already made a right connection, please contact your ISP to make sure if
your Internet service is available now.
2. If the Internet LED is off, please check your ADSL LED first. If your ADSL LED is also off,
please refer to Note 1. If your ADSL LED is GREEN ON, please check your Internet
4
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
configuration. You may need to check this part of information with your ISP and make sure
everything have been input correctly. Refer to 4.1.1 Device Info and 4.3.1 Internet for more
information.
2.2 The Back Panel
Figure 2-2
ON/OFF: The switch for the power.
POWER: The Power plug is where you will connect the power adapter.
USB: Connect with your computer’s USB interface.
LAN: Through the port, you can connect the modem router to your PC or the other Ethernet
network devices.
RESET: There are two ways to reset the modem router's factory defaults.
Method one: With the modem router powered on, use a pin to press and hold the Reset
button (about 5 seconds) until all LEDs are lit. And then release the button and wait for the
modem router to reboot to its factory default settings.
Method two：Restore the default setting from “Maintenance-SysRestart” of the Router's
Web-based Utility.
ADSL: Through the port, you can connect the modem router with the telephone.
2.3 Installation Environment
The Product should not be located where it will be exposed to moisture or excessive heat.
Place the modem router in a location where it can be connected to the various devices as
well as to a power source.
Make sure the cables and power cord are placed safely out of the way so they do not create a
tripping hazard.
The modem router can be placed on a shelf or desktop.
Generally, TD-8817 is placed on a horizontal surface. The device also can be mounted on the wall
5
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Figure 2-3
Note:
The diameter of the screw, 4mm<D<7.5mm, and the distance of two screws is 111.5mm. The
screw that project from the wall need around 4mm based, and the length of the screw need to be
at least 20mm to withstand the weight of the product.
2.4 Hardware Installation Procedures
The procedure to install the modem router can be described in the following steps:
First Step: Connect the Modem port of Splitter with the ADSL port of the modem router by
telephone line.
Second Step: Connect category 5 cable with RJ45 jacks to modem router’s LAN port and your
computer’s NIC. Or connect USB cable to ADSL2+ Ethernet/USB Modem Router’s USB port and
your computer’s USB interface. (When you connect your PC to the modem router through the
USB port, please install the USB driver first. For the detailed operation please refer to 3.2 USB
Third Step: Plug one end of the provided Power Adapter into the Power jack on the modem
router and the other end to a standard electrical outlet.
Last Step: Check the line connection to see if everything is ready. Power up finally.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Figure 2-4
7
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Chapter 3. Quick Installation Guide
3.1 TCP/IP Configuration
The default IP address of the TD-8817 ADSL2+ Ethernet/USB Modem Router is 192.168.1.1. And
the default Subnet Mask is 255.255.255.0. These values can be changed as you desire. In this
guide, we use all the default values for description.
Connect the local PC to the LAN port of the modem router. And then you can configure the IP
address for your PC in the following way.
Obtain an IP address automatically
1) Set up the TCP/IP Protocol in "Obtain an IP address automatically" mode on your PC.
If you need instructions as to how to do this, please refer to Appendix B: "Configuring the
PC”.
2) Then the built-in DHCP server will assign IP address for the PC.
Now, you can run the Ping command in the command prompt to verify the network connection.
Please click the Start menu on your desktop, select run tab, type cmd or command in the field
and press Enter. Type ping 192.168.1.1 on the next screen, and then press Enter.
If the result displayed is similar to the screen below, the connection between your PC and the
modem router has been established.
Figure 3-1
If the result displayed is similar to the screen shown below, it means that your PC has not
connected to the modem router.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Figure 3-2
You can check it following the steps below:
1) Is the connection between your PC and the modem router correct?
The LEDs of LAN port which you link to the device and the LEDs on your PC's adapter should
be lit.
2) Is the TCP/IP configuration for your PC correct?
If the modem router's IP address is 192.168.1.1, your PC's IP address must be within the
range of 192.168.1.2 ~ 192.168.1.254.
3.2 USB Configuration
If you use the USB interface, First, you must install the USB’s driver to the computer. You can
USB Drive installation procedures
Step 1: Please connect your PC to the modem router through the USB port at first, then insert
the provided CD into your CD-ROM drive. The autorun.exe will automatically run and
click Browse CD to read the files on the CD. Click the file TD-8817>USB Driver and
select the USB driver type according to the operating system of your computer to start
installation.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Figure 3-5
Note:
1) All of the above settings are under windows XP.
2) If you want to pull out the USB device you must disconnect the network of USB first.
3) In the Vista operating system, maybe the “Unknown Device” screen will pop up when you
insert the USB cable of the Router to a computer, please just unplug the USB cable and try
again.
3.3 Login
Once your host PC is properly configured, please proceed as follows to use the Web-based Utility:
Start your web browser and type the private IP address of the Router in the URL field: 192.168.1.1.
After that, you will see the screen shown below, enter the default User Name admin and the
default Password admin, and then click OK to access to the Quick Start screen. You can follow
the steps below to complete the Quick Setup.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Figure 3-6
the NEXT button.
Figure 3-7
Step 2: Configure the time for the Router, and then click the NEXT button.
Figure 3-8
Step 3: Select the connection type to connect to the ISP (We select PPPoE/PPPoA mode for
example here), and then click the NEXT button.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Figure 3-9
Step 4: Configure the following options provided by your ISP: Username, Password, VPI, VCI
and Connection Type. Then click NEXT.
Figure 3-10
Step 5: Click NEXT to finish the Quick Start.
Figure 3-11
13
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Chapter 4. Software Configuration
This User Guide recommends using the “Quick Installation Guide” for first-time installation. For
advanced users, if you want to know more about this device and make use of its functions
adequately, maybe you will get help from this chapter to configure the advanced settings through
the Web-based Utility.
After your successful login, you can configure and manage the device. There are main menus on
the top of the Web-based Utility, submenus will be available after you click one of the main menus.
On the center of the Web-based Utility, there are the detailed configurations or status information.
To apply any settings you have altered on the page, please click the SAVE button.
4.1 Status
Choose “Status”, you can see the next submenus: Device Info, System Log and Statistics.
Click any of them, and you will be able to configure the corresponding function.
Figure 4-1
4.1.1 Device Info
Choose “Status→Device Info” menu, and you will be able to view the device information,
including LAN, WAN and ADSL. The information will vary depending on the settings of the Router
configured on the Interface Setup screen.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Figure 4-3
The modem router can keep logs of all traffic. You can query the logs to find what happened to the
modem router.
Click the CLEAR LOG button to clear the logs.
Click the SAVE LOG button to save the logs.
4.1.3 Statistics
Choose “Status→Statistics” menu, and you will be able to view the network traffic over Ethernet,
and ADSL.
Figure 4-4
16
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Interface: You can select Ethernet and ADSL to view the corresponding network traffic over
different ports.
Select Ethernet, and you will see the statistics table as below.
Statistics Table:
Transmit Frames
The frames transmitted over the Ethernet port.
The multicast frames transmitted over the Ethernet
port.
Transmit Multicast Frames
Transmit total Bytes
Transmit Collision
Transmit
Statistics
The total bytes transmitted over the Ethernet port.
The collision occurred over the Ethernet port when
data is being transmitted.
The error frames over the Ethernet port when data is
being transmitted.
Transmit Error Frames
Receive Frames
The frames received over the Ethernet port.
The multicast frames received over the Ethernet port.
The total bytes received over the Ethernet port.
Receive Multicast Frames
Receive total Bytes
Receive
The CRC errors occurred over the Ethernet port when
data is being received.
Statistics
Receive CRC Errors
The Under-size frames received over the Ethernet
port.
Receive Under-size Frames
Select ADSL, and you will see the statistics table as below.
Statistics Table:
Transmit total PDUs
The total PDUs transmitted over the ADSL port.
Transmit
Statistics
The total errors occurred over the ADSL port when data
is being transmitted.
Transmit total Error Counts
Receive total PDUs
The total PDUs transmitted over the ADSL port.
Receive
The total errors occurred over the ADSL port when data
is being received.
Statistics
Receive total Error Counts
17
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
4.2 Quick Start
4.3 Interface Setup
Choose “Interface Setup”, you can see the next submenus: Internet and LAN.
Figure 4-5
Click any of them, and you will be able to configure the corresponding function.
4.3.1 Internet
Choose “Interface Setup→Internet” menu, you can configure the parameters for WAN ports in
18
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Figure 4-6
ATM VC: ATM settings are used to connect to your ISP. Your ISP provides VPI (Virtual Path
Identifier), VCI (Virtual Channel Identifier) settings to you. In this Device, you can totally setup
8 VCs on different encapsulations, if you apply 8 different virtual circuits from your ISP. You
need to activate the VC to take effect. For PVCs management, you can use ATM QoS to
setup each PVC traffic line's priority.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Virtual Circuit: Select the VC number you want to setup, PVC0~PVC7.
Status: If you want to use a designed VC, you should activate it.
VPI: Identifies the virtual path between endpoints in an ATM network. The valid range is
from 0 to 255. Please input the value provided by your ISP.
VCI: Identifies the virtual channel endpoints in an ATM network. The valid range is from
32 to 65535 (1 to 31 is reserved for well-known protocols). Please input the value
provided by your ISP.
PVCs Summary: Click the button, you can view the summary information about the
PVCs.
QoS: Select the Quality of Service types for this Virtual Circuit, including CBR (Constant
Bit Rate), UBR (Unspecified Bit Rate) and VBR (Variable Bit Rate). These QoS types are
all controlled by the parameters specified below, including PCR (Peak Cell Rate), SCR
(Sustained Cell Rate) and MBS (Maximum Burst Size), please configure them according
your needs.
4.3.1.1. IPv4
There are two IP versions: IPv4 and IPv6. If you select IPv4 as IP version, please follow the
configuration below to configure the parameters for WAN ports.
Encapsulation: There are four connection types: Dynamic IP Address, Static IP Address,
PPPoA/PPPoE and Bridge Mode. Please choose the designed type that you want to use.
After that, you should follow the configuration below to proceed.
1. Dynamic IP Address
Select this option if your ISP provides you an IP address automatically. This option is typically
used for Cable services. Please enter the Dynamic IP information accordingly.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Figure 4-7
Encapsulation: Select the encapsulation mode for the Dynamic IP Address, you can leave it
default.
Bridge Interface: Activate the option, the modem router can also work in Bridge mode.
Default Route: If enable this function, the current PVC will be considered as the default
gateway to Internet from this device.
TCP MTU Option: Enter the TCP MTU as your desire. The default value is 1500.
IPv4 Address: If you select IPv4 as IP version, you should configure the following.
NAT: Select this option to Enable/Disable the NAT (Network Address Translation) function
for this VC. The NAT function can be activated or deactivated per PVC basis.
Dynamic Route: Select this option to specify the RIP (Routing Information protocol) version
for WAN interface, including RIP1, RIP2-B and RIP2-M. RIP2-B and RIP2-M are both sent in
RIP2 format, the difference is that RIP2-M using Multicast, while RIP2-B using Broadcast
format.
Direction: Select this option to specify the RIP direction. None is for disabling the RIP
function. Both means the ADSL modem router will periodically send routing information and
accept routing information, and then incorporate them into routing table. IN only means the
ADSL modem router will only accept but will not send RIP packet. OUT only means the
ADSL modem router will only send but will not accept RIP packet.
Multicast: Select IGMP version, or disable the function. IGMP (Internet Group Multicast
Protocol) is a session-layer protocol used to establish membership in a multicast group. The
ADSL ATU-R supports IGMP version 1 (IGMP v1), IGMP version 2 (IGMP v2) and IGMP
version 3 (IGMP v3). Select “Disabled” to disable it.
Dual Stack Lite: Enable the Dual Stack Lite (D-S Lite) function if you need. It is disabled by
default.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
2. Static IP Address
Select this option if your ISP provides static IP information for you. You should set static IP
Figure 4-8
Note:
Each IP address entered in the fields must be in the appropriate IP form, which is four IP octets
separated by a dot (x.x.x.x), such as 192.168.1.100. The modem router will not accept the IP
address if it is not in this format.
3. PPPoA/PPPoE
Select this option if your ISP requires you to use a PPPoE connection. This option is typically
used for DSL services. Select Dynamic PPPoE to obtain an IP address automatically for your
PPPoE connection. Select Static PPPoE to use a static IP address for your PPPoE connection.
Please enter the information accordingly.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Figure 4-9
Service name: Specify a name for the PPPoA/PPPoE connection for recognition.
Username: Enter your username for your PPPoA/PPPoE connection to identify and verify
your account to the ISP.
Password: Enter your password for your PPPoA/PPPoE connection.
Encapsulation: For both PPPoA/PPPoE connection, you need to specify the type of
Multiplexing, either LLC or VC Mux.
Bridge Interface: Activate the option, the modem router can also work in Bridge mode.
Connection: For PPPoA/PPPoE connection, you can select Always on or Connect
on-Demand or Connect Manually. Connect on demand is dependent on the traffic. If there
is no traffic (or Idle) for a pre-specified period of time), the connection will tear down
automatically. And once there is traffic send or receive, the connection will be automatically
on.
Default Route: You should select Yes to configure the PVC as the default gateway to
Internet from this device.
Static/Dynamic IP Address: For PPPoA/PPPoE connection, you need to specify the public
IP address for this ADSL modem router. The IP address can be either dynamically (via DHCP)
23
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
or given by your ISP. For Static IP, you need to specify the IP address, Subnet Mask and
Gateway IP address.
Dual Stack Lite: Enable the Dual Stack Lite (D-S Lite) function if you need. It is disabled by
default.
4. Bridge Mode
If you select this type of connection, the modem router can be configured to act as a bridging
device between your LAN and your ISP. Bridges are devices that enable two or more networks to
communicate as if they are two segments of the same physical LAN.
Dual Stack Lite：Enable the Dual Stack Lite (D-S Lite) function if you need. It is disabled by
default.
Figure 4-10
Note:
After you finish the Internet configuration, please click SAVE to make the settings take effect.
4.3.1.2. IPv6
There are two IP versions: IPv4 and IPv6. If you select IPv6 as IP version, please follow the
configuration below to configure the parameters for WAN ports.
Encapsulation: There are four connection types: Dynamic IP Address, Static IP Address,
PPPoA/PPPoE and Bridge Mode. Please choose the designed type that you want to use.
After that, you should follow the configuration below to proceed.
1. Dynamic IP Address
Select this option if your ISP provides you an IP address automatically. This option is typically
used for Cable services. Please enter the Dynamic IP information accordingly.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Figure 4-11
IP Common Option: Configure the IP common option here.
Encapsulation: Select the encapsulation mode for the Dynamic IP Address, you can leave it
default.
Bridge Interface: Activate the option, the modem router can also work in Bridge mode.
Default Route: If enable this function, the current PVC will be considered as the default
gateway to Internet from this device.
TCP MTU Option: Enter the TCP MTU as your desire. The default value is 1500.
DHCP IPv6: There are two types of assignation for IPv6 address: DHCP (Dynamic Host
Configuration Protocol) Server and SLAAC (Stateless address auto-configuration). Select
your assignation type accordingly.
DHCP PD: The DHCP PD (Prefix Delegation) function is disabled by default. If you want to
enable the function, please click Enable.
MLD Proxy: The MLD (Multicast Listener Discovery Protocol) Proxy function is disabled by
default. If you want to enable the function, please click Enable.
Dual Stack Lite: Enable the Dual Stack Lite (D-S Lite) function if you need. It is disabled by
default.
2. Static IP Address
Select this option if your ISP provides static IP information for you. You should set static IP
address, IP Default Gateway and DNS Server address in the screen below (shown in Figure
4-12).
25
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Figure 4-12
Note:
Each IP address entered in the fields must be in the appropriate IPv6 form, which is eight IP
octets separated by a colon (x:x:x:x:x:x:x:x). The modem router will not accept the IP address if it
is not in this format.
3. PPPoA/PPPoE
Select this option if your ISP requires you to use a PPPoE connection. This option is typically
used for DSL services. Select Dynamic PPPoE to obtain an IP address automatically for your
PPPoE connection. Select Static PPPoE to use a static IP address for your PPPoE connection.
Please enter the information accordingly.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Figure 4-13
Service name: Specify a name for the PPPoA/PPPoE connection for recognition.
Username: Enter your username for your PPPoA/PPPoE connection to identify and verify
your account to the ISP.
Password: Enter your password for your PPPoA/PPPoE connection.
Encapsulation: For both PPPoA/PPPoE connection, you need to specify the type of
Multiplexing, either LLC or VC Mux.
Bridge Interface: Activate the option, the modem router can also work in Bridge mode.
Connection: For PPPoA/PPPoE connection, you can select Always on or Connect
on-Demand or Connect Manually. Connect on demand is dependent on the traffic. If there
is no traffic (or Idle) for a pre-specified period of time), the connection will tear down
automatically. And once there is traffic send or receive, the connection will be automatically
on.
TCP MSS Option：Enter the TCP MSS as your desire. The default value is 1400.
Default Route: You should select Yes to configure the PVC as the default gateway to
Internet from this device.
DHCP IPv6: There are two types of assignation for IPv6 address: DHCP (Dynamic Host
Configuration Protocol) Server and SLAAC (Stateless address auto-configuration). Select
your assignation type accordingly.
DHCP PD: The DHCP PD (Prefix Delegation) function is disabled by default. If you want to
27
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
enable the function, please click Enable.
MLD Proxy: The MLD (Multicast Listener Discovery Protocol) Proxy function is disabled by
default. If you want to enable the function, please click Enable.
Dual Stack Lite: Enable the Dual Stack Lite (D-S Lite) function if you need. It is disabled by
default.
4. Bridge Mode
If you select this type of connection, the modem router can be configured to act as a bridging
device between your LAN and your ISP. Bridges are devices that enable two or more networks to
communicate as if they are two segments of the same physical LAN.
Dual Stack Lite: Enable the Dual Stack Lite (D-S Lite) function if you need. It is disabled by
default.
Figure 4-14
Note:
After you finish the Internet configuration, please click SAVE to make the settings take effect.
4.3.1.3. IPv4/IPv6
configuration based on different connection types to configure the parameters for WAN ports.
4.3.2 LAN
Please configure the parameters for LAN ports according to the descriptions below.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Figure 4-15
Router Local IP: These are the IP settings of the LAN interface for the device. These
settings may be referred to as Private settings. You may change the LAN IP address if
needed. The LAN IP address is private to your internal network and cannot be seen on the
Internet.
IP Address: Enter the modem router’s local IP Address, then you can access to the
Web-based Utility via the IP Address, the default value is 192.168.1.1.
IP Subnet Mask: Enter the modem router’s Subnet Mask, the default value is
255.255.255.0.
Dynamic Route: Select this option to specify the RIP (Routing Information protocol)
version for LAN interface, including RIP1, RIP2-B and RIP2-M. RIP2-B and RIP2-M are
both sent in RIP2 format, the difference is that RIP2-M using Multicast, while RIP2-B
using Broadcast format.
Direction: Select this option to specify the RIP direction. None is for disabling the RIP
function. Both means the ADSL modem router will periodically send routing information
and accept routing information, and then incorporate them into routing table. IN only
means the ADSL modem router will only accept but will not send RIP packet. OUT only
29
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
means the ADSL modem router will only send but will not accept RIP packet.
Multicast: Select IGMP version, or disable the function. IGMP (Internet Group Multicast
Protocol) is a session-layer protocol used to establish membership in a multicast group.
The ADSL ATU-R supports both IGMP version 1 (IGMP v1) and IGMP v2. Select
“Disabled” to disable it.
IGMP Snoop: Enable the IGMP Snoop function if you need.
MldSnoop：Enable the MldSnoop function if you need.
modem router will work as a DHCP Server, it becomes the default gateway for DHCP client
connected to it. DHCP stands for Dynamic Host Control Protocol. The DHCP Server gives
out IP addresses when a device is booting up and request an IP address to be logged on to
the network. That device must be set as a DHCP client to obtain the IP address automatically.
By default, the DHCP Server is enabled. The DHCP address pool contains the range of the
IP address that will automatically be assigned to the clients on the network.
Figure 4-16
Starting IP Address: Enter the starting IP address for the DHCP server's IP assignment.
Because the default IP address for the modem router is 192.168.1.1, the default Start IP
Address is 192.168.1.100, and the Start IP Address must be 192.168.1.100 or greater,
but smaller than 192.168.1.254.
IP Pool Count: The max user pool size.
Lease Time: The length of time for the IP lease. After the dynamic IP address has
expired, the user will be automatically assigned a new dynamic IP address. The default
is 259200 seconds.
DNS Relay: If you want to disable this feature, you just need to set both Primary and
secondary DNS IP to 0.0.0.0. If you want to use DNS relay, you can setup DNS server IP
to 192.168.1.1 on their Computer. If not, the device will perform as no DNS relay.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Primary DNS Server: Type in your preferred DNS server.
Secondary DNS Server: Type in your preferred DNS server.
Note:
If Use Auto Discovered DNS Server Only is selected in DNS Relay, this router will accept the
first received DNS assignment from one of the PPPoA, PPPoE or MER/DHCP enabled PVC(s)
during the connection establishment. If Use User Discovered DNS Server Only is selected in
DNS Relay, it is necessary for you to enter the primary and optional secondary DNS server IP
addresses. After type in the address, click SAVE button to save it and invoke it.
modem router will work as a DHCP Relay. A DHCP relay is a computer that forwards DHCP
data between computers that request IP addresses and the DHCP server that assigns the
addresses. Each of the device's interfaces can be configured as a DHCP relay. If it is enabled,
the DHCP requests from local PCs will forward to the DHCP server runs on WAN side. To
have this function working properly, please run on Router mode only, disable the DHCP
server on the LAN port, and make sure the routing table has the correct routing entry.
Figure 4-17
DHCP Server IP for Relay Agent: Enter the DHCP server IP Address runs on WAN
side.
Note:
If you select Disabled, the DHCP function will not take effect.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
4.4 Advanced Setup
Choose “Advanced Setup”, you can see the next submenus:
Figure 4-18
Click any of them, and you will be able to configure the corresponding function.
4.4.1 Firewall
4-19).
Figure 4-19
Firewall: Select this option can automatically detect and block Denial of Service (DoS)
attacks, such as Ping of Death, SYN Flood, Port Scan and Land Attack.
SPI: If you enable SPI, all traffics initiated from WAN would be blocked, including DMZ,
Virtual Server, and ACL WAN side.
4.4.2 Routing
Choose “Advanced Setup→Routing” menu, and you will see the routing information in the next
Figure 4-20
32
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Figure 4-21
Destination IP Address: This parameter specifies the IP network address of the final
destination.
IP Subnet Mask: Enter the subnet mask for this destination.
Gateway IP Address: Enter the IP address of the gateway. The gateway is an immediate
neighbor of your ADSL modem router that will forward the packet to the destination. On the
LAN, the gateway must be a router on the same segment as your Router; over Internet
(WAN), the gateway must be the IP address of one of the remote nodes.
Metric: Metric represents the "cost" of transmission for routing purposes. IP Routing uses
hop count as the measurement of cost, with a minimum of 1 for directly connected networks.
Enter a number that approximates the cost for this link. The number need not to be precise,
but it must between 1 and 15. In practice, 2 or 3 is usually a good number.
Announced in RIP: This parameter determines if the ADSL modem router will include the
route to this remote node in its RIP broadcasts. If set to Yes, the route to this remote node will
be propagated to other hosts through RIP broadcasts. If No, this route is kept private and is
not included in RIP broadcasts.
4.4.3 NAT
Choose “Advanced Setup→NAT” menu, you can setup the NAT (Network Address Translation)
Figure 4-22
33
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Virtual Circuit: Enter Virtual Circuit Index that you plan to setup for the NAT function.
NAT Status: This field shows the current status of the NAT function for the current VC. You
Number of IPs; This field is to specify how many IPs are provided by your ISP for current VC.
It can be single IP or multiple IPs. We select Multiple to explain.
Note:
For VCs with single IP, they share the same DMZ and Virtual servers; for VCs with multiple IPs,
each VC can set DMZ and Virtual servers. Furthermore, for VCs with multiple IPs, they can define
the Address Mapping rules; for VCs with single IP, since they have only one IP, there is no need
to individually define the Address Mapping rule.
4.4.3.1. DMZ
next screen. A DMZ (demilitarized zone) is a host between a private local network and the outside
public network. It prevents outside users from getting direct access to a server that has company
data. Users of the public network outside the company can access to the DMZ host.
Figure 4-23
DMZ Host IP Address: Enter the specified IP Address for DMZ host on the LAN side.
4.4.3.2. Virtual Server
Server in the next screen.
The Virtual Server is the server or server(s) behind NAT (on the LAN), for example, Web server or
FTP server, that you can make visible to the outside world even though NAT makes your whole
inside network appear as a single machine to the outside world.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Figure 4-24
Rule Index: The Virtual server rule index for this VC. You can specify 10 rules in maximum.
All the VCs with single IP will use the same Virtual Server rules.
Start & End port number: Enter the specific Start and End Port number you want to forward.
If it is one port only, you can enter the same number for both the End port and the Start port.
For example, if you want to set the FTP Virtual server, you can set the start and end port
number to 21.
Local IP Address: Enter the IP Address for the Virtual Server in LAN side.
Virtual Server Listing: This displays the information about the Virtual Servers you establish.
To add a virtual server entry:
Note:
For VCs with single IP, select Single; For VCs with multiple IPs, select Multiple for the option.
Step 3: Select the application you want from drop-down list, then the protocol and port number
will be added to the corresponding field automatically, you only need to configure the IP
address for the virtual server; If the application list does not contain the service that you
want, please configure the Port number, IP Address and Protocol manually.
Step 4: After that, click SAVE to make the entry take effect.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Other operations for the entries are as follows:
Enter the index of assigned entry, click the DELETE button to delete the entry.
Click the BACK button to return to the previous screen.
Click the CANCEL button to cancel the configuration which is made just now.
4.4.3.3. IP Address Mapping
Choose “Advanced Setup→NAT”, select Multiple in Number of IPs. Click IP Address Mapping,
those VCs that configured with multiple IPs. The IP Address Mapping rule is per-VC based (only
for Multiple IPs' VCs).
Figure 4-25
Figure 4-26
Rule Index: Select the Address Mapping Rule index for this VC. You can specify 8 rules in
maximum.
Rule Type: There are four types, one-to-one, Many-to-One, Many-to-Many Overload and
Many-to-Many No-overload.
Local Start & End IP: Enter the local IP Address you plan to mapped to. Local Start IP is the
starting local IP address and Local End IP is the ending local IP address. If the rule is for all
local IPs, then the Start IP is 0.0.0.0 and the End IP is 255.255.255.255.
Public Start & End IP: Enter the public IP Address you want to do NAT. Public Start IP is the
starting public IP address and Public End IP is the ending public IP address. If you have a
dynamic IP, enter 0.0.0.0 as the Public Start IP.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Address Mapping List: This displays the information about the Mapping addresses.
To add a mapping rule:
Step 1: Select the “Virtual Circuit” and Multiple for the “Number of IPs”. Then select the tab IP
Note:
IP Address Mapping is only available for VCs with Multiple IPs.
Step 2: Select the Rule index for the rule as shown in Figure 4-26.
Step 3: Select the rule type you want from the drop-down list.
Step 4: Enter the local and public IP addresses in the corresponding fields.
Step 5: After that, click SAVE to make the entry take effect.
Other operations for the entries are as follows:
Enter the index of assigned entry, click the DELETE button to delete the entry.
Click the BACK button to return to the previous screen.
Click the CANCEL button to cancel the configuration which is made just now.
4.4.4 QoS
Choose “Advanced Setup→QoS”, you can configure the QoS in the next screen. QoS helps to
prioritize data as it enters your router. By attaching special identification marks or headers to
incoming packets, QoS determines which queue the packets enter, based on priority. This is
useful when you want to give certain types of data higher priority, such as giving voice data
packets higher priority than Web data packets. This option will provide better service of selected
network traffic over various technologies.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Figure 4-27
QoS: Select this option to Activate/Deactivate the IP QoS on different types.
Summary: Click the button to view the configurations of QoS.
Rule: Configure the rules for QoS. If the traffic complies with the rule, then the Router will
take the corresponding action to deal with it.
Rule Index: Select the index for the rule you want to configure.
Active: Activate the rule. The rule can take effect only when it is activated.
Application: Select the application that the rule aimed at.
Physical Ports: Select the port whose traffic flow are controlled by the rule.
Destination MAC & IP & Mask & Port Range: Enter the IP information about the
Destination host for the rule.
Source MAC & IP & Mask & Port Range: Enter the IP information about the Source
host for the rule.
Protocol ID: Select one among TCP/UDP, TCP, UDP or ICMP protocols for the
38
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
application.
Vlan ID Range: Enter the Vlan range, then the rule will be effective to the selected
Vlans.
IPP/DS Field: Select the type of the action to assign the priority.
When you select IPP/TOS, you can assign the priority via IP information. IP QoS function is
intended to deliver guaranteed as well as differentiated Internet services by giving network
resource and usage control to the Network operator.
IP Precedence Range: Enter the IP precedence range that the Router takes to
differentiate the traffic.
Type of Service: Select the type of service that the Router takes to deal with the traffic.
DSCP Range: Enter the DSCP range to differentiate the traffic.
When you select DSCP, you can assign the priority via DHCP (the header of IP group). It maps
the IP group into corresponding service class.
802.1p: Select the priority range for the rule.
Action: Configure the action that the Router takes to deal with the traffic which accord with
the rule.
IPP/DS Field: Select the type for the action.
IP Precedence Remarking: Select the number to remark the priority for IP precedence.
Type of Service Remarking: Select the type to remark the service.
DSCP Remarking: Enter the number to remark the DSCP priority.
802.1p Remarking: Select the type to remark the 802.1p priority.
Queue #: Select the priority type for the action.
There are two IP versions: IPv4 and IPv6. If you select IPv6 as IP version, please follow the
Figure 4-28
QoS: Select this option to Activate/Deactivate the IP QoS on different types.
Summary: Click the button to view the configurations of QoS.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Rule: Configure the rules for QoS. If the traffic complies with the rule, then the Router will
take the corresponding action to deal with it.
Rule Index: Select the index for the rule you want to configure.
Active: Activate the rule. The rule can take effect only when it is activated.
Destination IPv6: Enter the IP information about the Destination host for the rule.
Source IPv6: Enter the IP information about the Source host for the rule.
DSCP Range: Enter the DSCP range to differentiate the traffic.
When you select DSCP, you can assign the priority via DHCP (the header of IP group). It maps
the IP group into corresponding service class.
Action: Configure the action that the Router takes to deal with the traffic which accord with
the rule.
DSCP Remarking: Enter the number to remark the DSCP priority.
Queue #: Select the priority type for the action.
4.4.5 VLAN
Choose “Advanced Setup→VLAN”, you can activate the VLAN function in the next screen.
Virtual LAN (VLAN) is a group of devices on one or more LANs that are configured so that they
can communicate as if they were attached to the same LAN, when in fact they are located on a
number of different LAN segments. Because VLANs are based on logical instead of physical
connections, it is very flexible for user/host management, bandwidth allocation and resource
optimization. There are two types of VLAN as follows:
Port-Based VLAN: Each physical switch port is configured with an access list specifying
membership in a set of VLANs.
ATM VLAN: Using LAN Emulation (LANE) protocol to map Ethernet packets into ATM cells and
deliver them to their destination by converting an Ethernet MAC address into an ATM address.
Figure 4-29
in Figure 4-30).
40
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Figure 4-30
VLAN Index: Select the VLAN index for this VC. You can specify 8 groups in maximum.
VLAN ID: This indicates the VLAN group.
ATM VCs: Select the ATM VCs as members of VLAN, and if you leave the Tagged blank, the
tag in frames will be deleted when transmitted from the VC.
Ethernet: Select the Ethernet port as a member of VLAN, and if you leave the Tagged blank,
the tag in frames will be deleted when transmitted from the port.
USB: Select the USB port as a member of VLAN, and if you leave the Tagged blank, the tag
in frames will be deleted when transmitted from the port.
VLAN Group Summary: This displays the information about the VLAN Groups.
2. Assign VLAN PVID for each Interface
41
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Figure 4-31
PVID: Each physical port has a default VID called PVID (Port VID). PVID is assigned to
untagged frames or priority tagged frames (frames with null (0) VID) received on this port.
4.4.6 ADSL
Choose “Advanced Setup→ADSL”, you can select the ADSL Type and ADSL Mode in the next
screen. The ADSL feature can be selected when you meet the physical connection problem.
Please check the proper settings with your Internet service provider.
Figure 4-32
ADSL Mode: Select the ADSL operation mode which your ADSL connection uses.
ADSL Type: Select the ADSL operation type which your ADSL connection uses.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
4.5 Access Management
Choose “Access Management”, you can see the next submenus:
Figure 4-33
Click any of them, and you will be able to configure the corresponding function.
4.5.1 ACL
can specify the client to access the ADSL modem router once setting his IP as a Secure IP
Address through selected applications.
Figure 4-34
ACL: If Activated, the IP addresses which are contained in the Access Control List can
access to the modem router. If Deactivated, all IP addresses can access to the modem
router.
ACL Rule Index: Select the ACL rule index for the entry.
Active: Enable the ACL rule.
Secure IP Address: Select the IP addresses which are permitted to access to the modem
router remotely. With the default IP 0.0.0.0, any client would be allowed to remotely access
the ADSL modem router.
Application: Select the application for the ACL rule, and then you can access the Router
through it.
Interface: Select the interface for access: LAN, WAN or Both.
Access Control of Listing: This displays the information about the ACL Rules.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
4.5.2 Filter
Choose “Access Management→Filter”, you can see the Filter screen (the default is IP/MAC
Filter screen shown in Figure 4-35). The filtering feature includes IP/MAC Filter, Application Filter,
URL Filter. The feature makes it possible for administrators to control user's access to the Internet,
protect the networks.
4.5.2.1. IP Filter
then you can configure the filter rules based on IP address. The filtering includes Outgoing and
Incoming, the detailed descriptions are provided below.
Figure 4-35
Filter Type Selection: Select the filter type for the configuration below.
IP/MAC Filter Set Index: Select the Set index for the IP Filter entry. This index can match
with six IP / MAC Filter Rule Indexes.
Interface: Select the interface for the entry.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Note:
If select PVC0~PVC7 as a interface, the filter will match the IP traffic of WAN port with specified
IPs (Source IP Address and Destination IP Address), If select LAN as a interface, the filter will
match the IP traffic of LAN port with specified IPs.
Direction: Select the direction for this IP Filter rule. There are three filtering directions: Both,
Incoming, Outgoing.
Note:
Incoming means that IP traffic which is coming into the router, and the Outgoing means that IP
traffic which is going out the router.
IP/MAC Filter Rule Index: Select the Rule index for the IP Filter entry.
Note:
You should set the IP/MAC Filter Set Index and IP/MAC Filter Rule Index together to appoint
the address (shown in the Filter List) for the IP Filter rule. For example, (1, 2), it means the rule will
be shown in the row 2 IP/MAC Filter Set Index 1.
Rule Type: For IP Filter, please select IP here.
Active: Select “Yes” to make the rule to take effect.
Source IP Address: Enter the source IP address for the rule. You can enter 0.0.0.0; it means
that all IP addresses are controlled by the rule.
Subnet Mask: Enter the Subnet Mask for the rule.
Port Number: Enter the Port Number for the rule. You can enter 0, it means that all ports are
controlled by the rule.
Destination IP Address: Enter the destination IP address for the rule. You can enter 0.0.0.0,
it means that all IP addresses are controlled by the rule. The set of Subnet Mask and Port
Number are same as Source IP Address.
Protocol: Select the protocol: TCP, UDP or ICMP for the filter rule.
Rule Unmatched: If the current rule can not match, and you select Forward, the modem
router will skip the rule and transmit directly. If you select Next, the modem router will find the
next filter rule (show in Filter list) to match.
IP/MAC Filter Listing: This displays the information about the IP Filter rules.
To add an IP Address filtering entry:
For example: If you desire to block E-mail received and sent by the IP address 192.168.1.7 on
your local network; And wish to make the PCs with IP address 192.168.1.8 unable to visit the
website of IP address 202.96.134.12, while other PCs have no limit. You can configure the rules
as follows. Presume the rules are both aimed at the interface PVC0, and their indexes are (1, 1),
(1, 2) and (1, 3).
Select the “IP” as the Rule Type on the Filter screen, then you can configure the specific
rule for the example.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Step 2: Select the IP/MAC Filter Set Index and IP/MAC Filter Rule Index for the rule, then
select the Interface “PVC0”, and select the Direction “Both” for the first rule.
Note:
If you want to make the rule take effect, please select
to active the rule.
Yes
Step 3: Enter the “Source IP Address”, “Destination IP Address”, “Subnet Mask” and “Port
Number” in the corresponding field.
Step 4: Select the Protocol as “TCP” and select the Unmatched rule as “Next”.
Step 5: Finally, click the SAVE to save the entry.
Step 6: Go to Step 2 to configure the next two rules: Block E-mail received by the IP address
192.168.1.7 on your local network; Make the PC with IP address 192.168.1.8 unable to
visit the website of IP address 202.96.134.12.
Note:
After you complete the IP filter rules for the example, the Filter list will show as follows. You can
enter the IP / MAC Filter Set Index to view the information about the rule.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Select the IP / MAC Filter Set Index and IP/MAC Filter Rule Index to view or modify the entry.
Select the IP / MAC Filter Set Index and IP/MAC Filter Rule Index to locate the specific rule,
and then click the DELETE button to delete the entry.
4.5.2.2. MAC Filter
then you can configure the filter rules based on MAC address.
Figure 4-36
Rule Type: Select MAC for the MAC Filter rule.
Active: Select “Yes” to make the rule to take effect.
MAC Address: Enter the MAC address for the rule.
Rule Unmatched: If the current rule can not match, and you select Forward, the modem
router will skip the rule and transmit directly. If you select Next, the modem router will find the
next filter rule (show in Filter list) to match.
IP/MAC Filter Listing: This displays the information about the MAC Filter rules.
To add a MAC Address filtering entry:
For example: If you want to block the PCs with MAC addresses 00-0A-EB-00-07-BE and
00-0A-EB-00-07-5F to access the Internet, you can configure as follows. Presume the rules are
both aimed at the interface PVC0, and their indexes are (1, 1) and (1, 2).
47
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Step 1: Select the “IP/MAC Filter” as the Filer Type Selection:
, Then you can configure the specific rule for the example.
Step 2: Select the IP/MAC Filter Set Index and IP/MAC Filter Rule Index for the rule, then
select the Interface “PVC0”, and select the Direction “Outgoing” for the first rule.
Note:
If you want to make the rule take effect, please select
to active the rule.
Yes
Step 3: Enter the “MAC Address” and select the Unmatched rule as “Next”.
Step 4: Finally, click the SAVE to save the entry.
Step 5: Go to Step 2 to configure the next rule: Block the PC with MAC address
00-0A-EB-00-07-5F to access the Internet.
Note:
After you complete the MAC filter rules for the example, the Filter list will show as follows. You can
enter the IP / MAC Filter Set Index to view the information about the rule.
Other operations for the entries as shown in Figure 4-28:
Select the IP / MAC Filter Set Index and IP/MAC Filter Rule Index to view or modify the entry.
Select the IP / MAC Filter Set Index and IP/MAC Filter Rule Index to locate the specific rule,
and then click the DELETE button to delete the entry.
4.5.2.3. Application Filter
filter rules based on application.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Figure 4-37
Filter Type Selection: Select the Application Filter for the next configuration.
Application Filter: Activate or deactivate the function.
ICQ & MSN & YMSG & Real Audio/Video: Select Allow or Deny for these applications. If
you select Allow, the modem router will accept the application; if you select Deny, the
modem router will forbid the application.
4.5.2.4. URL Filter
Select URL Filter as the Filter type (shown in Figure 4-38), then you can configure the filter rules
based on URL.
Figure 4-38
49
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Filter Type Selection: Select the URL Filter for the next configuration.
Active: Select “Yes” to make the rule to take effect.
URL Index: Select the index for the URL Filter entry.
URL: Enter the URL for this URL Filter.
URL Filter Listing: This displays the information about the URL Filter rules.
To add a URL filter entry:
index is “1”.
Step 2: Select the Index for the rule, and then enter the website in the URL field.
Step 3: Finally, Select Yes to active the rule, and then click the SAVE to save the entry.
Select the URL Index to view or modify the entry.
Select the URL Index to locate the specific rule, and then click the DELETE button to delete the
entry.
4.5.3 SNMP
Choose “Access Management→SNMP”, you can see the SNMP screen. The Simple Network
Management Protocol (SNMP) is used for exchanging information between network devices.
Figure 4-39
SNMP: Activate or deactivate the function.
Get Community: Set the password for the incoming Get and Get next requests from the
management station.
Set Community: Set the password for incoming Set requests from the management station.
Trap Host: Enter the trap host here.
4.5.4 UPnP
Choose “Access Management→UPnP”, you can configure the UPnP in the screen (shown in
UPnP (Universal Plug and Play) is a distributed, open networking standard that uses TCP/IP for
50
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
simple peer-to-peer network connectivity between devices. An UPnP device can dynamically join
a network, obtain an IP address, convey its capabilities and learn about other devices on the
network. In turn, a device can leave a network smoothly and automatically when it is no longer in
use. UPnP broadcasts are only allowed on the LAN.
Figure 4-40
UPnP: Activate or Deactivate the UPnP function. Only when the function is activated, can the
UPnP take effect.
Auto-Configured: If you activate the function, then the UPnP network devices can
automatically configure network addressing, announce their presence in the network to other
UPnP devices and enable exchange of simple product and service descriptions.
4.5.5 DDNS
Choose “Access Management→DDNS”, you can configure the DDNS function in the screen
The modem router offers a Dynamic Domain Name System (DDNS) feature. The feature lets you
use a static host name with a dynamic IP address. User should type the host name, user name
and password assigned to your ADSL modem router by your Dynamic DNS provider.
Figure 4-41
Dynamic DNS: Activate the DDNS function or not.
Service Provider: This field displays the service provider of DDNS.
My Host Name: Enter your host name here.
Username & Password: Type the “User Name” and “Password” for your DDNS account.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
4.5.6 CWMP
Choose “Access Management→CWMP”, you can configure the CWMP function in the screen
The modem router offers CWMP feature. The function supports TR-069 protocol which collects
information, diagnoses the devices and configures the devices automatically via ACS
(Auto-Configuration Server).
Figure 4-42
CWMP: Select activate the CWMP function.
URL: Enter the website of ACS which is provided by your ISP.
User Name & Password: Enter the User Name and password to login the ACS server.
Path: Enter the path that connects to the ACS server.
Port: Enter the port that connects to the ACS server.
User Name & Password: Enter the User Name and Password that provided the ACS server
to login the modem router.
Periodic Inform: Activate or deactivate the function. If Activated, the information will be
informed to ACS server periodically.
Interval(s): Enter the interval time here.
4.6 Maintenance
Choose “Maintenance”, you can see the next submenus:
Figure 4-43
Click any of them, and you will be able to configure the corresponding function.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
4.6.1 Administration
Choose “Maintenance→Administration”, you can set new password for admin in the screen
Figure 4-44
Note:
1) There is only one account that can access Web-Management interface. The default account
is "admin", and the password is "admin". Admin has read/write access privilege.
2) When you change the password, you should enter the new password twice, and then click
SAVE to make the new password take effect.
4.6.2 Time Zone
Choose “Maintenance→Time Zone”, you can configure the system time in the screen (shown in
The system time is the time used by the device for scheduling services. There are three methods
to configure the time. You can manually set the time or connect to a NTP (Network Time Protocol)
server. If a NTP server is set, you will only need to set the time zone. If you manually set the time,
you may also set Daylight Saving dates and the system time will automatically adjust on those
dates.
1. NTP Server automatically
Select NTP Server automatically as the Synchronize time, you only need to set the time zone.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Figure 4-45
Note:
The ADSL modem router built-in some NTP Servers, when the modem router connects to the
Internet, the modem router will get the system time automatically from the NTP Server. You can
also configure the NTP Server address manually, and then the modem router will get the time
from the specific Server firstly.
2. PC’s Clock
Select PC’s Clock as the Synchronize time, you don’t need to set any items.
Figure 4-46
3. Manually
Select Manually as the Synchronize time, you need to set the date and time corresponding to the
current time.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Figure 4-47
4.6.3 Firmware
Choose “Maintenance→Firmware”, you can upgrade the firmware of the modem router in the
hard drive of the computer. Click Browse to find the local hard drive and locate the firmware or
romfile to be used for upgrade.
Figure 4-48
To upgrade the modem router's firmware, follow these instructions below:
Step 1: Download a more recent firmware upgrade file from the TP-LINK website
Step 2: Type the path and file name of the update file into the “New Firmware Location” field. Or
click the Browse button to locate the update file.
Step 3: Click the UPGRADE button.
Note:
the modem router is not experiencing difficulties, there is no need to download a more
55
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
recent firmware version, unless the version has a new feature that you want to use.
2) When you upgrade the modem router 's firmware, you may lose its current configurations,
so please back up the modem router’s current settings before you upgrade its firmware.
3) Do not turn off the modem router or press the Reset button while the firmware is being
upgraded.
4) The modem router will reboot after the upgrading has been finished.
To back up the modem router’s current settings:
Figure 4-49
TD-8817
Figure 4-50
To restore the modem router’s settings:
Step 1: Click the Browse button to locate the update file for the device, or enter the exact path
in “New Romfile Location” field.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Step 2: Click the UPGRADE button to complete.
4.6.4 SysRestart
Choose “Maintenance→SysRestart”, you can select to restart the device with current settings
Figure 4-51
4.6.5 Diagnostics
Choose “Maintenance→Diagnostics”, you can view the test results for the connectivity of the
Figure 4-52
57
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
4.7 Help
Choose “Help”, you can view the help information for configuration of any function.
Figure 4-53
Note:
Click the tab, and you will be able to get the corresponding information.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Appendix A: Specifications
General
ANSI T1.413, ITU G.992.1, ITU G.992.2, ITU G.992.3, ITU G.992.5
Standards and Protocols IEEE 802.3, IEEE 802.3u, TCP/IP, PPPoA , PPPoE, SNTP, HTTP,
DHCP, ICMP, NAT,CWMP
Safety & Emission
FCC, CE
1 10/100M Auto-Negotiation RJ45 port（Auto MDI/MDIX)
1 RJ11 port
Ports
1 USB 1.1 port
Power, USB, LAN, ADSL, Internet
LEDs
10Base-T: UTP category 3, 4, 5 cable
100Base-TX: UTP category-5
USB: USB cable
Network Medium
Max line length: 6.5Km
Downstream: Up to 24Mbps
Data Rates
Upstream: Up to 3.5Mbps（With Annex M enabled）
Internet Explorer 5.0 or later, Netscape Navigator 6.0 or later
Windows 9x/ME/2000/XP/Vista/7
Physical and Environment
0℃ ~ 40℃
System Requirement
Working Temperature
Working Humidity
10% ~ 90% RH (non-condensing)
-40℃ ~ 70℃
Storage Temperature
Storage Humidity
5% ~ 90% RH (non-condensing)
59
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Appendix B: Configuring the PC
In this section, we’ll introduce how to install and configure the TCP/IP correctly in Windows XP.
First make sure your Ethernet Adapter is working, refer to the adapter’s manual if necessary.
1. Configure TCP/IP component
1) On the Windows taskbar, click the Start button, and then click Control Panel.
2) Click the Network and Internet Connections icon, and then click on the Network
Connections tab in the appearing window.
3) Right click the icon that showed below, select Properties on the prompt page.
Figure B-1
4) In the prompt page that showed below, double click on the Internet Protocol (TCP/IP).
60
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Figure B-2
5) The following TCP/IP Properties window will display and the IP Address tab is open on
this window by default.
Now you have two ways to configure the TCP/IP protocol below:
Setting IP address automatically
Select Obtain an IP address automatically, Choose Obtain DNS server automatically, as
shown in the Figure below:
61
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Figure B-3
Note:
For Windows 98 OS or before, the PC and modem router may need to be restarted.
Setting IP address manually
1
2
Select Use the following IP address radio button. And the following items available
If the modem router's LAN IP address is 192.168.1.1, specify the IP address as 192.168.1.x
(x is from 2 to 254), and the Subnet mask as 255.255.255.0.
3
4
Type the modem router’s LAN IP address (the default IP is 192.168.1.1) into the Default
gateway field.
Select Use the following DNS server addresses. In the Preferred DNS Server field you
can enter the same value as the Default gateway or type the local DNS server IP address.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Figure B-4
Now:
Click OK to keep your settings.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Appendix C: Troubleshooting
T1. How do I restore my modem router’s configuration to its factory default
settings?
With the modem router powered on, press and hold the RESET button on the rear panel for 8 to
10 seconds before releasing it.
Note:
Once the modem router is reset, the current configuration settings will be lost and you will need to
re-configure the modem router.
T2. What can I do if I don’t know or forgot my password?
1) Restore the modem router’s configuration to its factory default settings. If you don’t know how
to do that, please refer to section T1.
2) Use the default user name and password: admin, admin.
T3. What can I do if I cannot access the web-based configuration page?
1) Configure your computer’s IP Address.
For Mac OS X
a) Click the Apple icon on the upper left corner of the screen.
b) Go to “System Preferences -> Network”.
c) Select Ethernet on the left menu bar. In the Configure IPv4 box, select Using DHCP.
d) Click Apply to save the settings.
For Windows 7
a) Click “Start -> Control Panel -> Network and Internet -> View network status -> Change
adapter settings”.
b) Right-click Local Area Connection and then click Properties.
c) Select Internet Protocol Version 4 (TCP/IPv4), and then click Properties.
d) Select Obtain an IP address automatically and Obtain DNS server address automatically.
Then click OK.
For Windows XP
a) Click “Start -> Control Panel -> Network and Internet Connections -> Network
Connections”.
b) Right-click Local Area Connection and then click Properties.
c) Select Internet Protocol (TCP/IP), and then click Properties.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
d) Select Obtain an IP address automatically and Obtain DNS server address
automatically. Then click OK.
For Windows 8
a) Move your mouse to the lower right corner and you will see Search icon
in the Popups.
Go to “ -> Apps”. Type Control Panel in the search box and press Enter, then you will go
to Control Panel.
b) Click “View network status and tasks > Change adapter settings”.
c) Right-click “Ethernet” and then select Properties.
d) Double-click Internet Protocol Version 4 (TCP/IPv4). Select Obtain an IP address
automatically, choose Obtain DNS server address automatically and then click OK.
2) Configure your IE browser
Open your IE browser, click
Tools tab and you will see the
following screen.
Click Internet Options
Select Never dial a connection
Click OK
65
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Now, try to log on to the Web-based configuration page again after the above settings have been
configured. If you still cannot access the configuration page, please restore your modem router’s
Please feel free to contact our Technical Support if the problem still exists.
T4. What can I do if I cannot access the Internet?
1) Check your cables and make sure they are all plugged in securely, including the telephone line,
Ethernet cables and power adapter.
2) Check to see if you can log on to the web management page of the Modem Router. If you can,
try the following steps.( If you cannot, please refer to T3 then try to see if you can access the
Internet again after following those steps. )
3) Consult your ISP and make sure all the VPI/VCI, Connection Type, account username and
password are correct. If there are any mistakes, please correct the settings and try again.
4) If you still cannot access the Internet, please restore your modem router to its factory default
5) Please feel free to contact our Technical Support if the problem still exists.
Note:
For more details about Troubleshooting and Technical Support contact information, please log on
to our Technical Support Website: http://www.tp-link.com/en/support .
66
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide
Appendix D: Technical Support
Technical Support
For more troubleshooting help, go to:
To download the latest Firmware, Driver, Utility and User Guide, go to:
For all other technical support, please contact us by using the following details:
Global
Tel: +86 755 2650 4400
Singapore
Tel: +65 6284 0493
Fee: Depending on rate of different carriers, IDD. Fee: Depending on rate of different carriers.
E-mail: [email protected]
E-mail: [email protected]
Service time: 24hrs, 7 days a week
Service time: 24hrs, 7 days a week
USA/Canada
UK
Toll Free: +1 866 225 8139
E-mail: [email protected]
Service time: 24hrs, 7 days a week
Tel: +44 (0) 845 147 0017
Fee: Landline: 1p-10.5p/min, depending on the time
of day. Mobile: 15p-40p/min, depending on your
mobile network.
E-mail: [email protected]
Service time: 24hrs, 7 days a week
Turkey
Tel: 0850 7244 488 (Turkish Service)
Fee: Depending on rate of different carriers.
E-mail: [email protected]
Service time: 09:00 to 21:00, 7 days a week
Italy
Tel: +39 023 051 9020
Fee: Depending on rate of different carriers.
E-mail: [email protected]
Service time: Monday to Friday, 09:00 to 13:00;
14:00 to 18:00
Ukraine
Tel: 0800 505 508
Fee: Free for Landline; Mobile: Depending on
rate of different carriers
E-mail: [email protected]
Malaysia
Service time: Monday to Friday, 10:00 to 22:00 Toll Free: 1300 88 875 465
Email: [email protected]
Service time: 24hrs, 7 days a week
Brazil
Toll Free: 0800 608 9799 (Portuguese Service)
E-mail: [email protected]
Poland
Service time: Monday to Friday, 09:00 to 20:00;Tel: +48 (0) 801 080 618
Saturday, 09:00 to 15:00
+48 223 606 363 (if calls from mobile phone)
Fee: Depending on rate of different carriers.
E-mail: [email protected]
Service time: Monday to Friday, 09:00 to 17:00.
GMT+1 or GMT+2 (DST)
Indonesia
Tel: (+62) 021 6386 1936
Fee: Depending on rate of different carriers.
E-mail: [email protected]
Service time: Monday to Friday, 09:00 to 18:00 France
*Except public holidays
Tel: 0820 800 860 (French service)
Fee: 0.118 EUR/min from France
Email: [email protected]
Service time: Monday to Friday, 09:00 to 18:00
*Except French Bank holidays
Australia/New Zealand
Tel: NZ 0800 87 5465 (Toll Free)
AU 1300 87 5465 (Depending on 1300 policy.)
E-mail: [email protected] (Australia)
[email protected] (New Zealand)
Service time: 24hrs, 7 days a week
Switzerland
Tel: +41 (0) 848 800 998 (German Service)
Fee: 4-8 Rp/min, depending on rate of different
time.
E-mail: [email protected]
Service time: Monday to Friday, 09:00 to 12:30 and
13:30 to 17:30. GMT+1 or GMT+2 (DST)
Germany/Austria
Tel: +49 1805 875 465 (German Service)
+49 1805 TPLINK
+43 820 820 360
Fee: Landline from Germany: 0.14EUR/min.
Landline from Austria: 0.20EUR/min.
E-mail: [email protected]
Service time: Monday to Friday, 09:00 to 12:30
Russian Federation
Tel: 8 (499) 754 5560 (Moscow NO.)
8 (800) 250 5560 (Toll-free within RF)
Germany)
Service time: From 9:00 to 21:00 (Moscow time)
*Except bank holidays in Hesse
*Except weekends and holidays in RF
67
Download from Www.Somanuals.com. All Manuals Search And Download.
|