TL-WR542G
54M Wireless Router
Rev: 1.1.0
1910010140
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may
cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This device and its antenna must not be co-located or
operating in conjunction with any other antenna or transmitter.
“To comply with FCC RF exposure compliance requirements, this grant is applicable to
only Mobile Configurations. The antennas used for this transmitter must be installed to
provide a separation distance of at least 20 cm from all persons and must not be
Download from Www.Somanuals.com. All Manuals Search And Download.
co-located or operating in conjunction with any other antenna or transmitter.”
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
National Restrictions
2400.0-2483.5 MHz
Country
Bulgaria
Restriction
Reason/remark
General authorization required for outdoor
use and public service
France
Outdoor use limited to Military Radiolocation use. Refarming of
10 mW e.i.r.p. within the 2.4 GHz band has been ongoing in
the band 2454-2483.5 recent years to allow current relaxed
MHz
regulation. Full implementation planned
2012
Italy
If used outside of own premises, general
authorization is required
Luxembourg
Norway
None
General authorization required for network
and service supply(not for spectrum)
Implemented
This subsection does not apply for the
geographical area within a radius of 20 km
from the centre of Ny-Ålesund
Russian
Only for indoor applications
Federation
Note：It’s not used outdoors in France.
Download from Www.Somanuals.com. All Manuals Search And Download.
TP-LINK TECHNOLOGIES CO., LTD
DECLARATION OF CONFORMITY
For the following equipment:
Product Description: 54M Wireless Router
Model No.: TL-WR542G
Trademark: TP-LINK
We declare under our own responsibility that the above products satisfy all the technical
regulations applicable to the product within the scope of Council Directives:
Directives 1999/5/EC
The above product is in conformity with the following standards or other normative
documents:
ETSI EN 300 328 V1.7.1: 2006
ETSI EN 301 489-1 V1.8.1:2008 & ETSI EN 301 489-17 V1.3.2:2008
EN 61000-3-2:2006
EN 61000-3-3:1995+A1:2001
EN60950-1:2006
EN50371:2002
Directives 2004/108/EC
The above product is in conformity with the following standards or other normative
documents
EN 55022:2006
EN 55024:1998+A1:2001+A2:2003
EN 61000-3-2:2006
EN 61000-3-3:1995+A1:2001+A2:2005
Directives 2006/95/EC
The above product is in conformity with the following standards or other normative
documents EN60950-1:2006
Person is responsible for marking this declaration:
Zhao Jianjun
Director of International Business
TP-LINK TECHNOLOGIES CO., LTD.
South Building, No.5 Keyuan Road, Central Zone, Science & Technology Park,
Nanshan,
Shenzhen, P. R. China
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Package Contents..................................................................................................... 1
Chapter 1.Introduction........................................................................................... 2
1.1 Overview of the Router................................................................................................2
1.2 Features...............................................................................................................................2
1.3 Panel Layout......................................................................................................................3
1.3.1 The Front Panel............................................................................................................3
1.3.2 The Rear Panel.............................................................................................................4
Chapter 2.Connecting the Router...................................................................... 6
2.1 System Requirements....................................................................................................6
2.2 Installation Environment Requirements................................................................6
2.3 Connecting the Router..................................................................................................6
Chapter 3.Quick Installation Guide................................................................... 8
3.1 TCP/IP configuration......................................................................................................8
3.2 Quick Installation Guide.............................................................................................10
Chapter 4.Configuring the Router ................................................................... 13
4.1 Login....................................................................................................................................13
4.2 Status..................................................................................................................................14
4.3 Quick Setup......................................................................................................................15
4.4 Network..............................................................................................................................16
4.4.1 LAN...................................................................................................................................16
4.4.2 WAN.................................................................................................................................16
4.4.3 MAC Clone....................................................................................................................27
4.5 Wireless..............................................................................................................................28
4.5.1 Wireless Settings.......................................................................................................28
4.5.2 MAC Filtering...............................................................................................................33
4.5.3 Wireless Statistics......................................................................................................36
4.6 DHCP...................................................................................................................................37
4.6.1 DHCP Settings.............................................................................................................37
4.6.2 DHCP Clients List.......................................................................................................38
4.6.3 Address Reservation................................................................................................39
4.7 Forwarding........................................................................................................................40
4.7.1 Virtual Servers ............................................................................................................40
4.7.2 Port Triggering............................................................................................................42
4.7.3 DMZ .................................................................................................................................44
4.7.4 UPnP................................................................................................................................45
Download from Www.Somanuals.com. All Manuals Search And Download.
4.8 Security ..............................................................................................................................46
4.8.1 Firewall...........................................................................................................................46
4.8.2 IP Address Filtering..................................................................................................47
4.8.3 Domain Filtering.........................................................................................................49
4.8.4 MAC Address Filtering.............................................................................................50
4.8.5 Advanced Security ....................................................................................................52
4.9 Static Routing..................................................................................................................54
4.10 IP QoS.................................................................................................................................56
4.11 IP & MAC Binding Setting..........................................................................................57
4.11.1 Binding Setting.......................................................................................................58
4.11.2 ARP List......................................................................................................................59
4.12 DDNS...................................................................................................................................60
4.12.1 Dyndns.org DDNS.................................................................................................60
4.12.2 Oray.net DDNS.......................................................................................................61
4.12.3 Comexe.cn DDNS..................................................................................................62
4.13 System Tools...................................................................................................................63
4.13.1 Time ............................................................................................................................64
4.13.2 Firmware...................................................................................................................65
4.13.3 Factory Defaults.....................................................................................................66
4.13.4 Backup & Restore..................................................................................................66
4.13.5 Reboot........................................................................................................................67
4.13.6 Password...................................................................................................................67
4.13.7 Syslog.........................................................................................................................68
4.13.8 Remote Management..........................................................................................69
4.13.9 Statistics....................................................................................................................69
Appendix A: FAQ...................................................................................................... 72
Appendix B: Configuring the PCs ..................................................................... 77
Appendix C: Specifications.................................................................................. 81
Appendix D: Glossary............................................................................................ 82
Download from Www.Somanuals.com. All Manuals Search And Download.
Package Contents
The following contents should be found in your box:
¾
¾
¾
¾
One TL-WR542G 54Mbps Wireless Router
One AC power Adapter for TL-WR542G 54Mbps Wireless Router
Quick Installation Guide
One Resource CD for TL-WR542G 54Mbps Wireless Router, including:
•
•
This Guide
Other Helpful Information
Note:
)
Make sure that the package contains the above items. If any of the listed items are damaged or
missing, please contact with your distributor.
Conventions
The router or TL-WR542G mentioned in this guide stands for TL-WR542G 54Mbps Wireless
Router without any explanation.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1. Introduction
Thank you for choosing TL-WR542G 54Mbps Wireless Router.
1.1 Overview of the Router
The TL-WR542G 54Mbps Wireless Router integrates 4-port Switch, Firewall, NAT-router and
Wireless AP. Its design is dedicated to Small Office/Home Office (SOHO) wireless network solutions.
The TL-WR542G 54Mbps Wireless Router will allow you to connect your network wirelessly better
than ever, sharing Internet Access, files and fun, easily and securely.
In the most attentive wireless security, the TL-WR542G 54Mbps Wireless Router provides
multiple protection measures. It can be set to turn off wireless network name (SSID) broadcast so
that only stations that have the SSID can be connected. The router provides wireless LAN
64/128/152-bit WEP encryption security, and WPA/WPA2 and WPA-PSK/WPA2-PSK
authentication, as well as TKIP/AES encryption security. It also supports VPN pass-through for
sensitive data secure transmission.
The TL-WR542G 54Mbps Wireless Router complies with the IEEE 802.11g and IEEE 802.11b
standards so that the data transmission rate is up to 54Mbps. It adopts 2x to 3x eXtended Range™
WLAN transmission technology so that the transmission distance is 2-3 times of traditional IEEE
802.11g and IEEE 802.11b solutions, up to a distance of 855.36m tested in China. The transmission
range is extended to 4-9 times. It is compatible with all IEEE 802.11g and IEEE 802.11b products.
The TL-WR542G 54Mbps Wireless Router provides flexible access control so that parents or network
administrators can establish restricted access policies for children or staff. It has built-in NAT and
DHCP server supporting static IP address distributing. It also supports Virtual Server and DMZ host
for Port Triggering needs, and remote management and log so that network administrators can
manage and monitor the network in real time. This device supports Bridge mode which can make
two APs communicate with each other wirelessly.
The TL-WR542G 54Mbps Wireless Router is easy-to-manage. Quick Setup is supported and
friendly help messages are provided for every step. So you can configure it quickly and share
Internet access, files and fun.
1.2 Features
¾
¾
Complies with IEEE 802.11g, IEEE 802.11b, IEEE 802.3, IEEE 802.3u standards.
1 10/100M Auto-Negotiation RJ45 WAN port, 4 10/100M Auto-Negotiation RJ45 LAN ports,
supporting Auto MDI/MDIX.
¾
Adopts 2x to 3x eXtended Range™ wireless LAN transmission technology.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
¾
¾
¾
Supports 54/48/36/24/18/12/9/6Mbps or 11/5.5/3/2/1Mbps data transfer rates.
Provides WPA/WPA2, WPA-PSK/WPA2-PSK authentication, TKIP/AES encryption security.
Shares data and Internet access for users, supporting PPPoE, Dynamic IP, Static IP, L2TP,
PPTP, Big Pond Cable Internet access.
¾
¾
¾
¾
¾
¾
Supports Virtual Server, Special Application and DMZ host.
Supports UPnP, Dynamic DNS, Static Routing, VPN Pass-through.
Detachable reverse SMA connector Antenna.
Connecting Internet on demand and disconnecting from the Internet when idle for PPPoE.
Built-in NAT and DHCP server supporting static IP address distributing.
Built-in firewall supporting IP address filtering, Domain Name filtering, and MAC address
filtering.
¾
¾
Supports connecting/disconnecting from the Internet on a specified time of day.
Supports access control, parents and network administrators can establish restricted access
policies based on time of day for children or staff.
¾
Provides 64/128/152-bit WEP encryption security and wireless LAN ACL (Access Control
List).
¾
¾
¾
¾
¾
Supports Flow Statistics.
Supports ICMP-FLOOD, UDP-FLOOD, and TCP-SYN-FLOOD filter.
Ignores Ping packets from WAN or LAN ports.
Supports firmware upgrade.
Supports Web management.
1.3 Panel Layout
1.3.1 The Front Panel
LEDs on the front panel of the router.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 1-1 Front Panel sketch
Indication
Name
Status
Off
No Power
PWR
On
Power on
Off
The Router has an error
The Router is initializing
SYS
On
Flashing The Router is working properly
Off The Wireless function is disabled
Flashing The Wireless function is enabled
WLAN
Off
On
There is no device linked to the corresponding port
There are devices linked to the corresponding ports but no data
transmitted or received.
WAN/1-4 (LAN)
Flashing Sending or receiving data over corresponding port
Table 1-1 The LEDs description
1.3.2 The Rear Panel
The following parts are located on the rear panel (View from left to right).
Please use the power adapter which is supplied with the TL-WR542G
¾ AC power socket:
54Mbps Wireless Router only, the use of a different adapter may result
in product damage.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Four 10/100Mbps RJ45 LAN ports for connecting the router to the local
PC(s)
¾ LAN 1,2,3,4:
¾ WAN:
This WAN port is where you will connect the cable/DSL Modem, or
Ethernet
¾ Reset button:
There are two ways to reset the router's factory defaults:
1) Use the Factory Defaults function on System Tools -> Factory Defaults page in the
router's Web-based Utility.
2) Use the Factory Default Reset button: With the router powered on, use a pin to press
and hold the Reset button(about 5 seconds) until the SYS LED becomes quick-flash
from slow-flash. And then release the button and wait the router to reboot to its factory
default settings.
Note: Ensure the router is powered on before it restarts completely.
)
¾
Wireless antenna
Figure 1-2 Rear Panel sketch
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2. Connecting the Router
2.1 System Requirements
¾
¾
Broadband Internet Access Service (DSL/Cable/Ethernet)
One DSL/Cable modem that has an RJ45 connector (you do not need it if you connect the
router to the Ethernet)
¾
Each PC in the LAN needs a working Ethernet Adapter and an Ethernet cable with RJ45
connectors
¾
¾
TCP/IP protocol must be installed on each PC
Web browser, such as Microsoft Internet Explorer 5.0 or later, Netscape Navigator 6.0 or later
2.2 Installation Environment Requirements
¾
¾
Do not place in direct sunlight or near a heater or heating vent
Do not cluttered or crowded. There should be at least 2 inches (5 cm) of clear space on all
sides of the router
¾
¾
¾
Well ventilated (especially if it is in a closet)
Operating temperature: 0℃~40℃ (32℉~104℉)
Operating Humidity: 10%~90%RH, Non-condensing
2.3 Connecting the Router
Before you install the router, you should connect your PC to the Internet through your broadband
service successfully. If there is any problem, please contact your ISP. After that, please install the
router according to the following steps. Don't forget to pull out the power plug and keep your
hands dry.
1. Power off your PC, Cable/DSL Modem, and the router.
2. Locate an optimum location for the router. The best place is usually near the center of the
area in which your PC will connect wirelessly. The place must accord with the Installation
3. Adjust the direction of the antenna. Normally, upright is a good direction.
4. Connect the PC(s) and each Switch/Hub in your LAN to the LAN Ports on the router, shown
this step.)
6
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Connect the AC power adapter to the AC power socket on the router, and the other end into
an electrical outlet. The router will start to work automatically.
7. Power on your PC and Cable/DSL Modem.
Figure 2-1 Hardware Installation of the TL-WR542G 54Mbps Wireless Router
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3. Quick Installation Guide
After connecting the TL-WR542G Router into your network, you should configure it. This chapter
describes how to configure the basic functions of your TL-WR542G Wireless Router. These
procedures only take you a few minutes. You can access the Internet via the router immediately
after successfully configuring.
3.1 TCP/IP configuration
The default IP address of the TL-WR542G 54Mbps Wireless Router is 192.168.1.1. And the
default Subnet Mask is 255.255.255.0. These values can be seen from the LAN. They can be
changed as you desire, as an example we use the default values for description in this guide.
Connect the local PC to the LAN ports of the router. There are then two ways to configure the IP
address for your PC.
¾
Configure the IP address manually
1) Set up the TCP/IP Protocol for your PC. If you need instructions as to how to do this,
please refer to Appendix B: "Configuring the PC."
2) Configure the network parameters. The IP address is 192.168.1.xxx ("xxx" is from 2 to
254), Subnet Mask is 255.255.255.0, and Gateway is 192.168.1.1 (The router's default
IP address)
¾
Obtain an IP address automatically
1) Set up the TCP/IP Protocol in "Obtain an IP address automatically" mode on your PC.
If you need instructions as to how to do this, please refer to Appendix B: "Configuring the
2) Power off the router and PC. Then turn on the router and restart the PC. The built-in
DHCP server will assign IP address for the PC.
Note: For Windows 98 OS or earlier, the PC and router may need to be restarted.
)
Now, you can run the Ping command in the command prompt to verify the network connection
between your PC and the router. The following example is in Windows 2000 OS.
Open a command prompt, and type ping 192.168.1.1, and then press Enter.
the router has been established.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 3-1 Success result of Ping command
If the result displayed is similar to that shown in Figure 3-2, it means that your PC has not
connected to the router.
Figure 3-2 Failure result of Ping command
Please check the connection following these steps:
1. Is the connection between your PC and the router correct?
Note:
)
The 1/2/3/4 LEDs of LAN port which you link to on the router and LEDs on your PC's adapter
should be lit.
2. Is the TCP/IP configuration for your PC correct?
Note:
)
9
Download from Www.Somanuals.com. All Manuals Search And Download.
If the router's IP address is 192.168.1.1, your PC's IP address must be within the range of
192.168.1.2 ~ 192.168.1.254, the gateway must be 192.168.1.1.
3.2 Quick Installation Guide
With a Web-based (Internet Explorer or Netscape® Navigator) utility, it is easy to configure and
manage the TL-WR542G 54Mbps Wireless Router. The Web-based utility can be used on any
Windows, Macintosh or UNIX OS with a Web browser.
Figure 3-3 Login the router
the User Name and Password, both in lower case letters. Then click the OK button or press the
Enter key.
Figure 3-4 Login Windows
Note:
)
If the above screen does not pop-up, it means that your Web-browser has been set to a proxy. Go
to Tools menu>Internet Options>Connections>LAN Settings, in the screen that appears, cancel
the Using Proxy checkbox, and click OK to finish it.
If the User Name and Password are correct, you can configure the router using the Web browser.
Please click the Quick Setup link on the left of the main menu and the Quick Setup screen will
appear.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 3-5 Quick Setup
Figure 3-6 Choose WAN Connection Type
The router supports three popular ways to connect to Internet. Please select one compatible with
your ISP. Click Next to enter the necessary network parameters.
Figure 3-7 Quick Setup - PPPoE
¾
Account Name and Password - Enter the Account Name and Password provided by your
ISP. These fields are case sensitive. If you have difficulty with this process, please contact
your ISP.
If you choose "Dynamic IP", the router will automatically receive the IP parameters from your ISP
without needing to enter any parameters.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 3-8 Quick Setup - Static IP
Note: The IP parameters should have been provided by your ISP.
)
¾
IP Address - This is the WAN IP address as seen by external users on the Internet (including
your ISP). Enter the IP address into the field.
¾
¾
¾
¾
Subnet Mask - The Subnet Mask is used for the WAN IP address, it is usually 255.255.255.0
Default Gateway - Enter the gateway IP address into the box if required.
Primary DNS - Enter the DNS Server IP address into the boxes if required.
Secondary DNS - If your ISP provides another DNS server, enter it into this field.
Figure 3-9 Quick Setup - Wireless settings
In this page, you can configure the following wireless parameters:
¾
Wireless Radio - Indicates whether the Access Point feature of the router is enabled or
disabled. If disabled, the WLAN LED on the front panel will not be lit and the wireless
12
Download from Www.Somanuals.com. All Manuals Search And Download.
stations will not be able to access the router. If enabled, the WLAN LED will be lit up and
wireless stations will be able to access the router.
¾
¾
SSID - Enter a value of up to 32 characters. The same SSID must be assigned to all
wireless devices on your network. The default SSID is TP-LINK_XXXXXX(XXXXXX
indicates the last unique six characters of each Router’s MAC address). This value is
case-sensitive. For example, TP-LINK is NOT the same as tp-link.
Region - Select your region from the pull-down list. This field specifies the region where the
wireless function of the router can be used. It may be illegal to use the wireless function of the
router in a region other than one of those specified in this field.
¾
¾
Channel - The current channel in use. This field determines which operating frequency will
be used.
Mode - Indicates the current mode 54Mbps (802.11g), 11Mbps (802.11b). If you select
54Mbps (802.11g), it is compatible with 11Mbps (802.11b).
These settings are only for basic wireless parameters, for advanced settings, please refer to
Note:
)
The change of wireless settings won't take effect until the router reboots! You can reboot it
Click the Next button. You will then see the Finish page:
Figure 3-10 Quick Setup - Finish
After finishing all configurations of basic network parameters, please click Finish button to exit
this Quick Setup.
Chapter 4. Configuring the Router
This chapter describes each Web page's key functions.
4.1 Login
After your successful login, you can configure and manage the router. There are twelve main
13
Download from Www.Somanuals.com. All Manuals Search And Download.
menus on the left of the Web-based utility. Submenus will be available after you click one of the
main menus. The twelve main menus are: Status, Quick Setup, Network, Wireless, DHCP,
Forwarding, Security, Static Routing, IP QoS, IP & MAC Binding Setting, DDNS and System
Tools. On the right of the Web-based utility, there are the detailed explanations and instructions
for the corresponding page. To apply any settings you have altered on the page, please click the
Save button.
The detailed explanations for each Web page key’s function are listed below.
4.2 Status
The Status page displays the router's current status and configuration. All information is
read-only.
1. LAN
This field displays the current settings or information for the LAN, including the MAC address,
IP address and Subnet Mask.
2. Wireless
This field displays basic information or status for wireless function, including Wireless Radio,
SSID, Channel, Mode, Wireless MAC address, and IP address.
3. WAN
These parameters apply to the WAN port of the router, including MAC address, IP address,
Subnet Mask, Default Gateway, DNS server and WAN connection type. If PPPoE is
chosen as the WAN connection type, the Disconnect button will be shown here while you
are accessing the Internet. You can also cut the connection by clicking the button. If you have
not connected to the Internet, just click Connect to establish the connection.
Traffic Statistics
This field displays the router's traffic statistics.
4. System Up Time
The total up time of the router from when it was switched on or reset.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
4.4 Network
Figure 4-2 the Network menu
Clone. Click any of them, and you will be able to configure the corresponding function. The
detailed explanations for each submenu are provided below.
4.4.1 LAN
You can configure the IP parameters of LAN on this page.
Figure 4-3 LAN
¾
MAC Address - The physical address of the router, as seen from the LAN. The value can't
be changed.
¾
IP Address - Enter the IP address of your router in dotted-decimal notation (factory default:
192.168.1.1).
¾
Subnet Mask - An address code that determines the size of the network. Normally use
255.255.255.0 as the subnet mask.
Note:
)
If you change the IP Address of LAN, you must use the new IP Address to login the router.
If the new LAN IP Address you set is not in the same subnet, the IP Address pool of the DHCP
server will not take effect, until they are re-configured.
If the new LAN IP Address you set is not in the same subnet, the Virtual Server and DMZ Host will
change accordingly at the same time.
4.4.2 WAN
You can configure the WAN port parameters on this page.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
First, please choose the WAN Connection Type (Dynamic IP/Static IP/PPPoE/802.1X + Dynamic
IP/802.1X + Static IP/Big Pond Cable/L2TP/PPTP) for Internet. The default type is Dynamic IP. If
you aren’t given any login parameters (fixed IP Address, logging ID, etc), please select Dynamic
IP. If you are given a fixed IP (static IP), please select Static IP. If you are given a user name and
a password, please select the type of your ISP provided (PPPoE/BigPond/L2TP/PPTP). If you
are not sure which connection type you use currently, please contact your ISP to obtain the
correct information.
1. If you choose Dynamic IP, the router will automatically get IP parameters from your ISP.
You can see the page as follows (Figure 4-4):
Figure 4-4 WAN – Dynamic IP
This page displays the WAN IP parameters assigned dynamically by your ISP, including IP
address, Subnet Mask, Default Gateway, etc. Click the Renew button to renew the IP
parameters from your ISP. Click the Release button to release the IP parameters.
MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks
is 1500 Bytes. For some ISPs you need to reduce the MTU. But this is rarely required, and
should not be done unless you are sure it is necessary for your ISP connection.
If your ISP gives you one or two DNS addresses, select Use These DNS Servers and enter
the primary and secondary addresses into the correct fields. Otherwise, the DNS servers will
be assigned dynamically from your ISP.
Note:
)
17
Download from Www.Somanuals.com. All Manuals Search And Download.
If you get address and find error when you go to a Web site, it is likely that your DNS servers
are set up improperly. You should contact your ISP to get DNS server addresses.
Get IP with Unicast DHCP - A few ISPs' DHCP servers do not support the broadcast
applications. If you cannot get the IP Address normally, you can choose this option. (This is
rarely required.)
2. If you choose Static IP, you should have fixed IP Parameters specified by your ISP. The
Static IP settings page will appear, shown in Figure 4-5:
Figure 4-5 WAN - Static IP
You should type the following parameters into the spaces provided:
¾
¾
IP Address - Enter the IP address in dotted-decimal notation provided by your ISP.
Subnet Mask - Enter the subnet Mask in dotted-decimal notation provided by your ISP,
usually is 255.255.255.0.
¾
¾
Default Gateway - (Optional) Enter the gateway IP address in dotted-decimal notation
provided by your ISP.
MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet
networks is 1500 Bytes. For some ISPs you may need to modify the MTU. But this is rarely
required, and should not be done unless you are sure it is necessary for your ISP
connection.
¾
¾
Primary DNS - (Optional) Enter the DNS address in dotted-decimal notation provided by
your ISP.
Secondary DNS - (Optional) Type another DNS address in dotted-decimal notation provided
by your ISP if provided.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 4-6 WAN - PPPoE
¾
¾
User Name/Password - Enter the User Name and Password provided by your ISP. These
fields are case-sensitive.
Connect on Demand - You can configure the router to disconnect your Internet connection
after a specified period of inactivity (Max Idle Time). If your Internet connection has been
terminated due to inactivity, Connect on Demand enables the router to automatically
re-establish your connection as soon as you attempt to access the Internet again. If you wish
to activate Connect on Demand, click the radio button. If you want your Internet connection
to remain active at all times, enter 0 in the Max Idle Time field. Otherwise, enter the number
of minutes you want to have elapsed before your Internet connection terminates.
Caution: Sometimes the connection cannot be disconnected although you specify a time to
Max Idle Time, since some applications is visiting the Internet continually in the background.
¾
¾
Connect Automatically - Connect automatically after the router is disconnected. To use this
option, click the radio button.
Time-based Connecting - You can configure the router to make it connect or disconnect
based on time. Enter the start time in HH:MM format for connecting and end time in HH:MM
format for disconnecting in the Period of Time fields.
Note:
)
Only when you have configured the system time on System Tools -> Time page, will the
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Time-based Connecting function can take effect.
¾
Connect Manually - You can configure the router to make it connect or disconnect manually.
After a specified period of inactivity (Max Idle Time), the router will disconnect from the
Internet connection, and you will not be able to re-establish your connection automatically as
soon as you attempt to access the Internet again. To use this option, click the radio button. If
you want your Internet connection to remain active at all times, enter "0" in the Max Idle Time
field. Otherwise, enter the number time in minutes that you wish to have the Internet
connecting last unless a new link is requested.
Caution: Sometimes the connection cannot be disconnected although you specify a time to
Max Idle Time, since some applications are visiting the Internet continually in the background.
Click the Connect button to connect immediately. Click the Disconnect button to disconnect
immediately.
Figure 4-7 PPPoE Advanced Settings
¾
Packet MTU - The default MTU size is 1480 bytes, which value is usually fine. For some
ISPs, you need modify the MTU. This should not be done unless you are sure it is necessary
for your ISP.
¾
¾
Service Name/AC Name - The service name and AC (Access Concentrator) name, these
should not be configured unless you are sure it is necessary for your ISP.
ISP Specified IP Address - If you know that your ISP does not automatically transmit your IP
20
Download from Www.Somanuals.com. All Manuals Search And Download.
address to the router during login, click “Use the IP Address specified by ISP” check box
and enter the IP Address in dotted-decimal notation, which your ISP provided.
¾
¾
Detect Online Interval - The default value is 0, you can input the value between 0 and 120.
The router will detect Access Concentrator online at every interval between seconds. If the
value is 0, it means, do not detect.
DNS IP address - If you know that your ISP does not automatically transmit DNS addresses
to the router during login, click “Use the following DNS servers” checkbox and enter the IP
address in dotted-decimal notation of your ISP’s primary DNS server. If a secondary DNS
server address is available, enter it as well.
Click the Save button to save your settings.
Figure 4-8 802.1X + Dynamic IP Settings
¾
¾
User Name - Enter the user name for 802.1X authentication provided by your ISP
Password - Enter the password for 802.1X authentication provided by your ISP.
Click Login to start 802.1X authentication.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Click Logout to end 802.1X authentication.
¾
Host Name - This field is required to be filled by some service provider.
Figure 4-9 802.1X + Static IP Settings
¾
¾
User Name - Enter the user name for 802.1X authentication provided by your ISP
Password - Enter the password for 802.1X authentication provided by your ISP.
Click Login to start 802.1X authentication.
Click Logout to end 802.1X authentication.
¾
¾
¾
IP Address - Enter the IP address in dotted-decimal notation provided by your ISP.
Subnet Mask - Enter the subnet Mask in dotted-decimal notation provided by your ISP.
Default Gateway - (Optional) Enter the default gateway IP address in dotted-decimal
notation provided by your ISP.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 4-10 Big Pond Settings
¾
User Name/Password - Enter the User Name and Password provided by your ISP. These
fields are case-sensitive.
¾
¾
Auth Server - Enter the authenticating server IP address or host name.
Auth Domain - Type in the domain suffix server name based on your location. E.g.,
NSW / ACT - nsw.bigpond.net.au
VIC / TAS / WA / SA / NT - vic.bigpond.net.au
QLD - qld.bigpond.net.au
¾
Connect on Demand - You can configure the router to disconnect from your Internet
connection after a specified period of inactivity (Max Idle Time). If your Internet connection
has been terminated due to inactivity, Connect on Demand enables the router to
automatically re-establish your connection as soon as you attempt to access the Internet
again. If you wish to activate Connect on Demand, click the radio button. If you want your
Internet connection to remain active at all times, enter 0 in the Max Idle Time field. Otherwise,
enter the number of minutes you want to have elapsed before your Internet connection
terminates.
Caution: Sometimes the connection cannot be disconnected although you specify a time to
Max Idle Time, since some applications are visiting the Internet continually in the
background.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
¾
¾
Connect Automatically - Connect automatically after the router is disconnected. To use this
option, click the radio button.
Connect Manually - You can configure the router to make it connect or disconnect manually.
After a specified period of inactivity (Max Idle Time), the router will disconnect from your
Internet connection, and you will not be able to re-establish your connection automatically as
soon as you attempt to access the Internet again. To use this option, click the radio button. If
you want your Internet connection to remain active at all times, enter "0" in the Max Idle Time
field. Otherwise, enter the number in minutes that you wish to have the Internet connecting
last unless a new link is requested.
Caution: Sometimes the connection cannot be disconnected although you specify a time to
Max Idle Time, since some applications are visiting the Internet continually in the background.
Click the Connect button to connect immediately. Click the Disconnect button to disconnect
immediately.
Figure 4-11 L2TP Settings
24
Download from Www.Somanuals.com. All Manuals Search And Download.
¾
¾
User Name/Password - Enter the User Name and Password provided by your ISP. These
fields are case-sensitive.
Dynamic IP/ Static IP – Choose either as you are given by your ISP.
Click the Connect button to connect immediately. Click the Disconnect button to disconnect
immediately.
¾
Connect on Demand - You can configure the router to disconnect from your Internet
connection after a specified period of inactivity (Max Idle Time). If your Internet connection
has been terminated due to inactivity, Connect on Demand enables the router to
automatically re-establish your connection as soon as you attempt to access the Internet
again. If you wish to activate Connect on Demand, click the radio button. If you want your
Internet connection to remain active at all times, enter 0 in the Max Idle Time field. Otherwise,
enter the number of minutes you want to have elapsed before your Internet connection
terminates.
Caution: Sometimes the connection cannot be disconnected although you specify a time to
Max Idle Time, since some applications is visiting the Internet continually in the background.
¾
¾
Connect Automatically - Connect automatically after the router is disconnected. To use this
option, click the radio button.
Connect Manually - You can configure the router to make it connect or disconnect manually.
After a specified period of inactivity (Max Idle Time), the router will disconnect from your
Internet connection, and you will not be able to re-establish your connection automatically as
soon as you attempt to access the Internet again. To use this option, click the radio button. If
you want your Internet connection to remain active at all times, enter "0" in the Max Idle Time
field. Otherwise, enter the number in minutes that you wish to have the Internet connecting
last unless a new link is requested.
Caution: Sometimes the connection cannot be disconnected although you specify a time to
Max Idle Time, since some applications is visiting the Internet continually in the background.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 4-12 PPTP Settings
¾
¾
User Name/Password - Enter the User Name and Password provided by your ISP. These
fields are case-sensitive.
Dynamic IP/ Static IP – Choose either as you are given by your ISP and enter the ISP’s IP
address or the domain name.
If you choose static IP and enter the domain name, you should also enter the DNS assigned
by your ISP. And click the Save button.
Click the Connect button to connect immediately. Click the Disconnect button to disconnect
immediately.
¾
Connect on Demand - You can configure the router to disconnect from your Internet
connection after a specified period of inactivity (Max Idle Time). If your Internet connection
has been terminated due to inactivity, Connect on Demand enables the router to
automatically re-establish your connection as soon as you attempt to access the Internet
again. If you wish to activate Connect on Demand, click the radio button. If you want your
Internet connection to remain active at all times, enter 0 in the Max Idle Time field. Otherwise,
26
Download from Www.Somanuals.com. All Manuals Search And Download.
enter the number of minutes you want to have elapsed before your Internet connection
terminates.
Caution: Sometimes the connection cannot be disconnected although you specify a time to
Max Idle Time, since some applications are visiting the Internet continually in the
background.
¾
¾
Connect Automatically - Connect automatically after the router is disconnected. To use this
option, click the radio button.
Connect Manually - You can configure the router to make it connect or disconnect manually.
After a specified period of inactivity (Max Idle Time), the router will disconnect from your
Internet connection, and you will not be able to re-establish your connection automatically as
soon as you attempt to access the Internet again. To use this option, click the radio button. If
you want your Internet connection to remain active at all times, enter "0" in the Max Idle Time
field. Otherwise, enter the number in minutes that you wish to have the Internet connecting
last unless a new link is requested.
Caution: Sometimes the connection cannot be disconnected although you specify a time to
Max Idle Time, since some applications are visiting the Internet continually in the background.
4.4.3 MAC Clone
Figure 4-13 MAC Address Clone
Some ISPs require that you register the MAC Address of your adapter, which is connected to your
cable/DSL Modem or Ethernet during installation. Changes are rarely needed here.
¾
WAN MAC Address - This field displays the current MAC address of the WAN port, which is
used for the WAN port. If your ISP requires that you register the MAC address, please enter
the correct MAC address into this field. The format for the MAC Address is
XX-XX-XX-XX-XX-XX (X is any hexadecimal digit).
¾
Your PC's MAC Address - This field displays the MAC address of the PC that is managing
the router. If the MAC address is required, you can click the Clone MAC Address button
and this MAC address will fill in the WAN MAC Address field.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Click Restore Factory MAC to restore the MAC address of WAN port to the factory default
value.
Click the Save button to save your settings.
Note:
)
1) Only the PC on your LAN can use the MAC Address Clone feature.
2) If you click the Save button, the router will prompt you to reboot.
4.5 Wireless
Figure 4-14 Wireless menu
There are three submenus under the Wireless menu (shown in
Figure 4-14): Wireless Settings, MAC Filtering and Wireless Statistics. Click any of them, and
you will be able to configure the corresponding function. The detailed explanations for each
submenu are provided below.
4.5.1 Wireless Settings
The basic settings for the wireless network are set on this page, Figure 4-15:
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 4-15 Wireless Settings
¾
SSID - Enter a value of up to 32 characters. The same name (SSID) must be assigned to all
wireless devices in your network. The default SSID is TP-LINK_XXXXXX(XXXXXX indicates
the last unique six characters of each Router’s MAC address), but it is recommended
strongly that you change your networks name (SSID) to a different value. This value is
case-sensitive. For example, TP-LINK is NOT the same as tp-link.
¾
Region - Select your region from the pull-down list. This field specifies the region where the
wireless function of the router can be used. It may be illegal to use the wireless function of
the router in a region other than one of those specified in this field. If your country or region
is not listed, please contact your local government agency for assistance.
The default region is United States. When you select your local region from the pull-down list.
Click the Save button, then the Note Dialog appears. Click OK.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Note Dialog
Note:
)
Limited by local law regulations, version for North America does not have region selection
option.
¾
¾
Channel - This field determines which operating frequency will be used. It is not necessary
to change the wireless channel unless you notice interference problems with another nearby
access point.
Mode - Select the desired wireless mode. The options are:
•
54Mbps (802.11g) - Both 802.11g and 802.11b wireless stations can connect to the
router.
•
11Mbps (802.11b) - Only 802.11b wireless stations can connect to the router.
Note:
)
The default is "54Mbps (802.11g)", which allows both 802.11g and 802.11b wireless stations to
connect to the router.
¾
Enable Wireless Router Radio - The wireless radio of this Router can be enabled or
disabled to allow wireless stations access. If enabled, wireless stations will be able to
access the router. Otherwise, wireless stations will not be able to access.
¾
¾
Enable SSID Broadcast - If you select the Enable SSID Broadcast checkbox, the Wireless
Router SSID will broadcast its name (SSID) on the air.
Enable Bridges – If you select the Enable Bridges checkbox, you can input MAC address
of other APs to communicate with them wirelessly in Bridge mode.
•
MAC of AP (1-6): Input the MAC address of the AP which you want to communicate
with. There are six entries can be configured.
The APs can communicate with each other in Bridge mode unless they know each other’s
MAC address. For example, if the router whose MAC address is 00-13-56-A8-9E-1A wants
to communicate with an AP whose MAC address is 00-13-56-A8-9E-1B in Bridge mode, you
should do as following:
1. Select Enable Bridges and input 00-13-56-A8-9E-1B as following screen shown.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Access the AP's Web-based utility and configure the AP under Bridge mode, then input
00-13-56-A8-9E-1A in corresponding Blank.
¾
¾
Enable Wireless Security – The wireless security function can be enabled or disabled. If
disabled, the wireless stations will be able to connect the router without encryption. It is
recommended strongly that you choose this option to encrypt your wireless network. The
encryption settings are described below.
Authentication Type - You can select one of the following authentication types:
•
•
WEP - Select WEP authentication type based on 802.11 authentications.
WPA-PSK/WPA2-PSK - Select WPA/WPA2 authentication type based on pre-shared
passphrase.
•
WPA /WPA2 - Select WPA/WPA2 authentication type based on Radius Server.
¾
Authentication Options - You can select one of the following authentication options:
•
When you select WEP for authentication type you can select the following
authentication options:
•
Automatic - Select Shared Key or Open System authentication type automatically
based on the wireless station request.
•
•
•
Shared Key - Select 802.11 Shared Key authentication.
Open System - Select 802.11 Open System authentication.
When you select WPA-PSK/WPA2-PSK for authentication type you can select
Automatic, WPA –PSK or WPA2-PSK as authentication options.
•
When you select WPA/WPA2 as an authentication type you can select Automatic
WPA or WPA2 as authentication option.
¾
WEP Key Format - You can select ASCII or Hexadecimal format. ASCII Code Format
stands for any combination of keyboard characters in the specified length. Hexadecimal
31
Download from Www.Somanuals.com. All Manuals Search And Download.
format stands for any combination of hexadecimal digits (0-9, a-f, A-F) in the specified
length.
¾
¾
WEP Key settings - Select which of the four keys will be used and enter the matching WEP
key information for your network in the selected key radio button. These values must be
identical on all wireless stations in your network.
Key Type - You can select the WEP key length (64-bit, or 128-bit, or 152-bit) for encryption.
"Disabled" means the WEP key entry is invalid.
•
•
•
For 64-bit encryption - You can enter 10 hexadecimal digits (any combination of 0-9, a-f,
A-F, zero key is not permitted) or 5 ASCII characters.
For 128-bit encryption - You can enter 26 hexadecimal digits (any combination of 0-9,
a-f, A-F, zero key is not permitted) or 13 ASCII characters.
For 152-bit encryption - You can enter 32 hexadecimal digits (any combination of 0-9,
a-f, A-F, zero key is not permitted) or 16 ASCII characters.
¾
Encryption - When you select WPA-PSK/WPA2-PSK or WPA/WPA2 for Authentication
Type you can select Automatic, TKIP or AES as Encryptions.
Figure 4-16 WPA-PSK/WPA2-PSK
¾
¾
WPA-PSK/WPA2-PSK Passphrase - You can enter a WPA or WPA2 passphrase between
8 and 63 characters long.
Group Key Update Period - Specify the group key update interval in seconds. The value
can be either 0 seconds or from 30 seconds and up, 1-29 seconds are not usable figures.
Enter 0 to disable the update.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 4-17 WPA/WPA2
Radius Server IP - Enter the IP address of the Radius Server
Radius Port - Enter the port number that the radius service used.
Radius Password - Enter the password for the Radius Server.
¾
¾
¾
Be sure to click the Save button to save your settings on this page.
Note: The router will reboot automatically after you click Save.
)
4.5.2 MAC Filtering
The Wireless MAC Filtering for wireless networks is set on this page, Figure 4-18:
Figure 4-18 Wireless MAC address Filtering
The Wireless MAC Address Filtering feature allows you to control wireless stations accessing the
router, which depend on the station's MAC addresses.
¾
¾
MAC Address - The wireless station's MAC address that you want to access.
Status - The status of this entry either Enabled or Disabled.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
¾
Privilege - Select the privileges for this entry. You may select one of the following Allow /
Deny / 64-bit / 128-bit / 152-bit.
¾
¾
Description - A simple description of the wireless station.
WEP Key - Specify a unique WEP key (in Hexadecimal format) to access the router.
To set up an entry, follow these instructions:
First, you must decide whether the unspecified wireless stations can access the router or not. If
you desire that the unspecified wireless stations can access the router, please select the radio
button Allow the stations not specified by any enabled entries in the list to access,
otherwise, select the radio button Deny the stations not specified by any enabled entries in
the list to access.
To Add a Wireless MAC Address filtering entry, click the Add New… button. The "Add or Modify
Figure 4-19 Add or Modify Wireless MAC Address Filtering entry
To add or modify a MAC Address Filtering entry, follow these instructions:
1. Enter the appropriate MAC Address into the MAC Address field. The format of the MAC
Address is XX-XX-XX-XX-XX-XX (X is any hexadecimal digit). For example:
00-0A-EB-B0-00-0B.
2. Enter a simple description of the wireless station in the Description field. For example:
Wireless station A.
3. Privilege - Select the privileges for this entry, one of Allow / Deny / 64-bit / 128-bit / 152-bit.
4. WEP Key - If you select 64-bit, 128-bit or 152-bit in the Privilege field, enter any
combination of hexadecimal digits (0-9, a-f, A-F) in the specified length. For example:
2F34D20BE2.
5. Status - Select Enabled or Disabled for this entry on the Status pull-down list.
6. Click the Save button to save this entry.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
To add additional entries, repeat steps 1-6.
Note: When 64-bit, or 128-bit, or 152-bit is selected, WEP key will be enabled.
)
To modify or delete an existing entry:
1. Click the Modify in the entry you want to modify. If you want to delete the entry, click the
Delete.
2. Modify the information.
3. Click the Save button.
Click the Enable All button to make all entries enabled
Click the Disabled All button to make all entries disabled.
Click the Delete All button to delete all entries
Click the Next button to go to the next page and click the Previous button to return to the
previous page.
For example: If you desire that the wireless station A with MAC address 00-0A-EB-00- 07-BE be
able to access the router. The wireless station B with MAC address 00-0A-EB- 00-07-5F not be able
to access the router, and the wireless station C with MAC address 00-0A-EB-00-07-8A be able to
access the router when its WEP key is 2F34D20BE2E 54B326C5476586A, while all other wireless
stations cannot access the router, you should configure the Wireless MAC Address Filtering list
by following these steps:
1. Click the Enable button to enable this function.
2. Select the radio button: Deny the stations not specified by any enabled entries in the list
to access for Filtering Rules.
3. Delete all or disable all entries if there are any entries already.
4. Click the Add New... button and enter the MAC address 00-0A-EB-00-07-BE in the MAC
Address field, enter wireless station A in the Description field, select Allow in the Privilege
pull-down list and select Enabled in the Status pull-down list. Click the Save and the Return
button.
5. Click the Add New... button and enter the MAC address 00-0A-EB-00-07-5F in the MAC
Address field, enter wireless station B in the Description field, select Deny in the Privilege
pull-down list and select Enabled in the Status pull-down list. Click the Save and the Return
button.
6. Click the Add New... button and enter the MAC address 00-0A-EB-00-07-8A in the MAC
Address field, enter wireless station C in the Description field, select 128-bit in the Privilege
35
Download from Www.Somanuals.com. All Manuals Search And Download.
pull-down list, enter 2F34D20BE2E54B326C5476586A in the WEP Key field and select
Enabled in the Status pull-down list. Click the Save and the Return button.
The filtering rules that configured should be similar to the following list:
Note:
)
a) If you select the radio button Allow the stations not specified by any enabled entries
in the list to access for Filtering Rules, the wireless station B will still not be able to
access the router, however, other wireless stations that are not in the list will be able to
access the router.
b) If you enable the function and select the Deny the stations not specified by any
enabled entries in the list to access for Filtering Rules, and there are not any enable
entries in the list, thus, no wireless stations can access the router.
4.5.3 Wireless Statistics
This page shows MAC Address, Current Status, Received Packets and Sent Packets for each
connected wireless station.
Figure 4-20 The router attached wireless stations
¾
¾
MAC Address - The connected wireless station's MAC address
Current Status - The connected wireless station's running status, one of STA-AUTH /
STA-ASSOC / AP-UP / WPA / WPA-PSK /WPA2/WPA2-PSK/None
¾
¾
Received Packets - Packets received by the station
Sent Packets - Packets sent by the station
You cannot change any of the values on this page. To update this page and to show the current
connected wireless stations, click on the Refresh button.
If the numbers of connected wireless stations go beyond one page, click the Next button to go to
the next page and click the Previous button to return the previous page.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: This page will be refreshed automatically every 5 seconds.
)
4.6 DHCP
Figure 4-21 The DHCP menu
DHCP Clients List and Address Reservation. Click any of them, and you will be able to
configure the corresponding function. The detailed explanations for each submenu are provided
below.
4.6.1 DHCP Settings
The router is set up by default as a DHCP (Dynamic Host Configuration Protocol) server, which
provides the TCP/IP configuration for all the PC(s) that are connected to the router on the LAN.
Figure 4-22 DHCP Settings
¾
DHCP Server - Enable or Disable the DHCP server. If you disable the Server, you must
have another DHCP server within your network or else you must manually configure the
computer.
¾
¾
Start IP Address - This field specifies the first of the addresses in the IP address pool.
192.168.1.100 is the default start address.
End IP Address - This field specifies the last of the addresses in the IP address pool.
192.168.1.199 is the default end address.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
¾
¾
Address Lease Time - The Address Lease Time is the amount of time in which a network
user will be allowed connection to the router with their current dynamic IP Address. Enter the
amount of time, in minutes. The user will be "leased" this dynamic IP Address. The range of
the time is 1 ~ 2880 minutes. The default value is 120 minutes.
Default Gateway - (Optional.) Suggest to input the IP address of the LAN port of the router,
default value is 192.168.1.1
¾
¾
Default Domain - (Optional.) Input the domain name of your network.
Primary DNS - (Optional.) Input the DNS IP address provided by your ISP. Or consult your
ISP.
¾
Secondary DNS - (Optional.) Input the IP address of another DNS server if your ISP
provides two DNS servers.
Note:
)
To use the DHCP server function of the router, you must configure all computers on the LAN as
"Obtain an IP Address automatically" mode. This function will take effect until the router reboots.
4.6.2 DHCP Clients List
This page shows Client Name, MAC Address, Assigned IP and Lease Time for each DHCP
Client attached to the router (Figure 4-23):
Figure 4-23 DHCP Clients List
¾
¾
¾
¾
¾
Index - The index of the DHCP Client
Client Name - The name of the DHCP client
MAC Address - The MAC address of the DHCP client
Assigned IP - The IP address that the router has allocated to the DHCP client.
Lease Time - The time of the DHCP client leased. Before the time is up, DHCP client will
request to renew the lease automatically.
You cannot change any of the values on this page. To update this page and to show the current
attached devices, click on the Refresh button.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
4.6.3 Address Reservation
When you specify a reserved IP address for a PC on the LAN, that PC will always receive the
same IP address each time when it accesses the DHCP server. Reserved IP addresses should
be assigned to servers that require permanent IP settings. This page is used for address
Figure 4-24 Address Reservation
¾
¾
¾
MAC Address - The MAC address of the PC of which you want to reserve IP address.
Assigned IP Address - The IP address of the router reserved.
Status - The status of this entry either Enabled or Disabled.
To Reserve IP addresses:
2. Enter the MAC address (The format for the MAC Address is XX-XX-XX-XX-XX-XX.) and IP
address in dotted-decimal notation of the computer you wish to add.
3. Click the Save button when finished.
Figure 4-25 Add or Modify an Address Reservation Entry
To modify or delete an existing entry:
1. Click the Modify in the entry you want to modify. If you want to delete the entry, click the
Delete.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Modify the information.
3. Click the Save button.
Click the Enable All button to make all entries enabled
Click the Disabled All button to make all entries disabled.
Click the Delete All button to delete all entries
Click the Next button to go to the next page and Click the Previous button to return the previous
page.
Note: The function won’t take effect until the router reboots.
)
4.7 Forwarding
Figure 4-26 The Forwarding menu
Port Triggering, DMZ and UPnP. Click any of them, and you will be able to configure the
corresponding function. The detailed explanations for each submenu are provided below.
4.7.1 Virtual Servers
Virtual servers can be used for setting up public services on your LAN, such as DNS, Email and
FTP. A virtual server is defined as a service port, and all requests from the Internet to this service
port will be redirected to the computer specified by the server IP. Any PC that was used for a
virtual server must have a static or reserved IP Address because its IP Address may change
when using the DHCP function. You can set up virtual servers on this page, shown in Figure
Figure 4-27 Virtual Servers
40
Download from Www.Somanuals.com. All Manuals Search And Download.
¾
Service Port - The numbers of External Ports. You can type a service port or a range of
service ports (the format is XXX – YYY, XXX is the start port, YYY is the end port).
¾
¾
IP Address - The IP Address of the PC providing the service application.
Protocol - The protocol used for this application, either TCP, UDP, or All (all protocols
supported by the router).
¾
Status - The status of this entry either Enabled or Disabled.
To setup a virtual server entry:
2. Select the service you want to use from the Common Service Port list. If the Common
Service Port list does not have the service that you want to use, type the number of the
service port or service port range in the Service Port box.
3. Type the IP Address of the computer in the Server IP Address box.
4. Select the protocol used for this application, either TCP or UDP, or All.
5. Select the Enable checkbox to enable the virtual server.
6. Click the Save button.
Figure 4-28 Add or Modify a Virtual Server Entry
Note:
)
It is possible that you have a computer or server that has more than one type of available service.
If so, select another service, and enter the same IP Address for that computer or server.
To modify or delete an existing entry:
1. Click the Modify in the entry you want to modify. If you want to delete the entry, click the
Delete.
2. Modify the information.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Click the Save button.
Click the Enable All button to make all entries enabled
Click the Disabled All button to make all entries disabled.
Click the Delete All button to delete all entries
Click the Next button to go to the next page and Click the Previous button to return the previous
page.
Note:
)
If you set the virtual server of service port as 80, you must set the Web management port on
Security –> Remote Management page to be any value except 80 such as 8080. Or else there
will be a conflict to disable the virtual server.
4.7.2 Port Triggering
Some applications require multiple connections, like Internet games, video conferencing, Internet
calling and so on. These applications cannot work with a pure NAT router. Port Triggering is
used for some of these applications that can work with an NAT router. You can set up Port
Triggering on this page shown in Figure 4-29:
Figure 4-29 Port Triggering
Once configured, operation is as follows:
1. A local host makes an outgoing connection using a destination port number defined in the
Trigger Port field.
2. The router records this connection, opens the incoming port or ports associated with this
entry in the Port Triggering table, and associates them with the local host.
3. When necessary the external host will be able to connect to the local host using one of the
ports defined in the Incoming Ports field.
¾
Trigger Port - The port for outgoing traffic. An outgoing connection using this port will
"Trigger" this rule.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
¾
¾
Trigger Protocol - The protocol used for Trigger Ports, either TCP, UDP, or All (all
protocols supported by the router).
Incoming Ports Range - The port or port range used by the remote system when it
responds to the outgoing request. A response using one of these ports will be forwarded to
the PC that triggered this rule. You can input at most 5 groups of ports (or port section).
Every group of ports must be set apart with ",". For example, 2000-2038, 2050-2051, 2085,
3010-3030.
¾
¾
Incoming Protocol - The protocol used for Incoming Ports Range, either TCP or UDP, or
ALL (all protocols supported by the router).
Status - The status of this entry either Enabled or Disabled.
To add a new rule, enter the following data on the Port Triggering screen.
2. Enter a port number used by the application when it generates an outgoing request.
3. Select the protocol used for Trigger Port from the pull-down list, either TCP, UDP, or All.
4. Enter the range of port numbers used by the remote system when it responds to the PC's
request.
5. Select the protocol used for Incoming Ports Range from the pull-down list, either TCP or
UDP, or All.
6. Select the Enable checkbox to enable.
7. Click the Save button to save the new rule.
Figure 4-30 Add or Modify a Triggering Entry
43
Download from Www.Somanuals.com. All Manuals Search And Download.
There are many popular applications in the Popular Application list. You can select it, and the
application will fill in the Trigger Port, incoming Ports Range boxes and select the Enable
checkbox. It has the same effect as adding a new rule.
To modify or delete an existing entry:
1. Click the Modify in the entry you want to modify. If you want to delete the entry, click the
Delete.
2. Modify the information.
3. Click the Save button.
Click the Enable All button to make all entries enabled
Click the Disabled All button to make all entries disabled.
Click the Delete All button to delete all entries.
Note:
)
1. When the trigger connection is released, the according opening ports will be closed.
2. Each rule allowed to be used only by one host on LAN synchronously. The trigger connection
of other hosts on LAN will be refused.
3. Incoming Port Range cannot overlap each other.
4.7.3 DMZ
The DMZ host feature allows one local host to be exposed to the Internet for a special-purpose
service such as Internet gaming or videoconferencing. DMZ host forwards all the ports at the
same time. Any PC whose port is being forwarded must have its DHCP client function disabled
and should have a new static IP Address assigned to it because its IP Address may change when
using the DHCP function. You can set up DMZ host on this page shown in Figure 4-31:
Figure 4-31 DMZ
To assign a computer or server to be a DMZ server:
1. Click the Enable radio button
2. Enter the local host IP Address in the DMZ Host IP Address field
3. Click the Save button.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: After you set the DMZ host, the firewall related to the host will not work.
)
4.7.4 UPnP
The Universal Plug and Play (UPnP) feature allows the devices, such as Internet computers, to
access the local host resources or devices as needed. UPnP devices can be automatically
discovered by the UPnP service application on the LAN. You can configure UPnP on this page
Figure 4-32 UPnP Settings
¾
¾
Current UPnP Status - UPnP can be enabled or disabled by clicking the Enable or Disable
button. As allowing this may present a risk to security, this feature is disabled by default.
Current UPnP Settings List - This table displays the current UPnP information.
•
•
•
•
•
•
App Description – The description provided by the application in the UPnP request
External Port - External port, which the router opened for the application.
Protocol – Shows which type of protocol is opened.
Internal Port - Internal port, which the router opened for local host.
IP Address - The UPnP device that is currently accessing the router.
Status - Either Enabled or Disabled, “Enabled” means that port is still active. Otherwise,
the port is inactive.
Click Refresh to update the Current UPnP Settings List.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
4.8 Security
Figure 4-33 The Security menu
Filtering, Domain Filtering, MAC Address Filtering and Advanced Security. Click any of them,
and you will be able to configure the corresponding function. The detailed explanations for each
submenu are provided below.
4.8.1 Firewall
The default setting for the switch is off. If the general firewall switch is off, even if IP Address
Filtering, DNS Filtering and MAC Filtering are enabled, their settings are ineffective.
Figure 4-34 Firewall Settings
¾
¾
Enable Firewall - the general firewall switch is on or off.
Enable IP Address Filtering - set IP Address Filtering is enabled or disabled. There are two
default filtering rules of IP Address Filtering, either Allow or Deny passing through the router.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
¾
¾
Enable Domain Filtering - set Domain Filtering is enabled or disabled.
Enable MAC Filtering - set MAC Address Filtering is enabled or disabled. You can select the
default filtering rules of MAC Address Filtering, either Allow or Deny accessing the router.
4.8.2 IP Address Filtering
The IP address Filtering feature allows you to control Internet Access by specific users on your
LAN based on their IP addresses. The IP address filtering is set on this page, Figure 4-35:
Figure 4-35 IP address Filtering
To disable the IP Address Filtering feature, keep the default setting, Disabled. To set up an IP
Address Filtering entry, click Enable Firewall and Enable IP Address Filtering on the Firewall
page, and click the Add New… button. The page "Add or Modify an IP Address Filtering entry"
will appear shown in Figure 4-36:
Figure 4-36 Add or Modify an IP Address Filtering Entry
To create or modify an IP Address Filtering entry, please follow these instructions:
47
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Effective Time - Enter a range of time in HHMM format, which point to the range time for the
entry to take effect. For example, 0803 - 1705, the entry will take effect from 08:03 to 17:05.
2. LAN IP Address - Enter a LAN IP Address or a range of LAN IP addresses in the field, in
dotted-decimal notation format. For example, 192.168.1.20 - 192.168.1.30. Keep the field
open, which means all LAN IP Addresses have been put into the field.
3. LAN Port - Enter a LAN Port or a range of LAN ports in the field. For example, 1030 - 2000.
Keep the field open, which means all LAN ports have been put into the field.
4. WAN IP Address - Enter a WAN IP Address or a range of WAN IP Addresses in the field, in
dotted-decimal notation format. For example, 61.145.238.6 – 61.145.238.47. Keep the field
open, which means all WAN IP Addresses have been put into the field.
5. WAN Port -Enter a WAN Port or a range of WAN Ports in the field. For example, 25 – 110.
Keep the field open, which means all WAN Ports have been put into the field.
6. Protocol - Select which protocol is to be used, either TCP, UDP, or All (all protocols
supported by the router).
7. Action - Select either Allow or Deny through the router.
8. Status - Select Enabled or Disabled for this entry on the Status pull-down list.
9. Click the Save button to save this entry.
To modify or delete an existing entry:
1. Click the Modify in the entry you want to modify. If you want to delete the entry, click the
Delete.
2. Modify the information.
3. Click the Save button.
Click the Enable All button to make all entries enabled
Click the Disabled All button to make all entries disabled.
Click the Delete All button to delete all entries
You can change the entry’s order as desired. Fore entries are before hind entries. Enter the ID
number in the first box you want to move and another ID number in second box you want to move
to, and then click the Move button to change the entry’s order.
Click the Next button to the next page and click the Previous button to return to the previous
page.
For example: If you desire to block E-mail received and sent by the IP Address 192.168.1.7 on
your local network, and to make the PC with IP Address 192.168.1.8 unable to visit the website of
48
Download from Www.Somanuals.com. All Manuals Search And Download.
IP Address 202.96.134.12, while other PC(s) have no limit you should specify the following IP
address filtering list:
4.8.3 Domain Filtering
on the Internet by specifying their domains or key words.
Figure 4-37 Domain Filtering
Before adding a Domain Filtering entry, you must ensure that Enable Firewall and Enable
Domain Filtering have been selected on the Firewall page. To Add a Domain filtering entry, click
the Add New… button. The page "Add or Modify a Domain Filtering entry" will appear, shown
Figure 4-38 Add or Modify a Domain Filtering entry
To add or modify a Domain Filtering entry, follow these instructions:
1. Effective Time - Enter a range of time in HHMM format specifying the time for the entry to
take effect. For example, if you enter: 0803 - 1705, than the entry will take effect from 08:03
49
Download from Www.Somanuals.com. All Manuals Search And Download.
to 17:05.
2. Domain Name - Type the domain or key word as desired in the field. A blank in the domain
3. Status - Select Enabled or Disabled for this entry on the Status pull-down list.
4. Click the Save button to save this entry.
To modify or delete an existing entry:
1. Click the Modify in the entry you want to modify. If you want to delete the entry, click the
Delete.
2. Modify the information.
3. Click the Save button.
Click the Enabled All button to make all entries enabled.
Click the Disabled All button to make all entries disabled.
Click the Delete All button to delete all entries
Click the Next button to go to the next page and the Previous button to return to the previous
page.
www.aabbcc.com and websites with .net in the end on the Internet while no limit for other
websites, you should specify the following Domain filtering list:
4.8.4 MAC Address Filtering
you to control access to the Internet by users on your local network based on their MAC Address.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 4-39 MAC address Filtering
Before setting up MAC Filtering entries, you must ensure that Enable Firewall and Enable MAC
Filtering have been selected on the Firewall page. To Add a MAC Address filtering entry, clicking
the Add New… button. The page "Add or Modify a MAC Address Filtering entry" will appear,
Figure 4-40 Add or Modify a MAC Address Filtering entry
To add or modify a MAC Address Filtering entry, follow these instructions:
1. Enter the appropriate MAC Address into the MAC Address field. The format of the MAC
Address is XX-XX-XX-XX-XX-XX (X is any hexadecimal digit). For example:
00-0E-AE-B0-00-0B.
2. Type the description of the PC in the Description field. Fox example: John’s PC.
3. Status - Select Enabled or Disabled for this entry on the Status pull-down list.
4. Click the Save button to save this entry.
To add additional entries, repeat steps 1-4.
When finished, click the Return button to return to the MAC Address Filtering page.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
To modify or delete an existing entry:
1. Click the Modify in the entry you want to modify. If you want to delete the entry, click the
Delete.
2. Modify the information.
3. Click the Save button.
Click the Enable All button to make all entries enabled.
Click the Disabled All button to make all entries disabled.
Click the Delete All button to delete all entries
Click the Next button to go to the next page and click the Previous button to return to the
previous page.
Fox example: If you want to block the PC with MAC addresses 00-0A-EB-00-07-BE and
00-0A-EB-00-07-5F to access the Internet, first, enable the Firewall and MAC Address Filtering
on the Firewall page, then, you should specify the Default MAC Address Filtering Rule "Deny
these PC(s) with effective rules to access the Internet" on the Firewall page and the following
MAC address filtering list on this page:
4.8.5 Advanced Security
attacked by TCP-SYN Flood, UDP Flood and ICMP-Flood from LAN.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 4-41 Advanced Security settings
¾
Packets Statistic interval (5 ~ 60) - The default value is 10. Select a value between 5 and
60 seconds in the pull-down list. The Packets Statistic interval value indicates the time
section of the packets statistic. The result of the statistic used for analysis by SYN Flood,
UDP Flood and ICMP-Flood.
¾
¾
¾
DoS protection - Enable or Disable the DoS protection function. Only when it is enabled,
will the flood filters be effective.
Enable ICMP-FLOOD Attack Filtering - Enable or Disable the ICMP-FLOOD Attack
Filtering.
ICMP-FLOOD Packets threshold: (5 ~ 3600) - The default value is 50. Enter a value
between 5 ~ 3600 packets. When the current ICMP-FLOOD Packets number sis beyond the
set value, the router will start up the blocking function immediately.
¾
¾
Enable UDP-FLOOD Filtering - Enable or Disable the UDP-FLOOD Filtering.
UDP-FLOOD Packets threshold: (5 ~ 3600) - The default value is 50. Enter a value
between 5 ~ 3600 packets. When the current UPD-FLOOD Packets numbers is beyond the
set value, the router will start up the blocking function immediately.
¾
¾
Enable TCP-SYN-FLOOD Attack Filtering - Enable or Disable the TCP-SYN- FLOOD
Attack Filtering.
TCP-SYN-FLOOD Packets threshold: (5 ~ 3600) - The default value is 50. Enter a value
53
Download from Www.Somanuals.com. All Manuals Search And Download.
between 5 ~ 3600 packets. When the current TCP-SYN-FLOOD Packets numbers is
beyond the set value, the router will start up the blocking function immediately.
¾
¾
Ignore Ping Packet from WAN Port - Enable or Disable ignore ping packet from WAN port.
The default is disabled. If enabled, the ping packet from the Internet cannot access the
router.
Forbid Ping Packet from LAN Port - Enable or Disable forbidding Ping Packet to access
the router from the LAN port. The default value is disabled. If enabled, the ping packet from
the LAN port cannot access the router. (Defends against some viruses)
Click the Save button to save the settings.
Click the Blocked DoS Host Table button to display the DoS host table by blocking. The page
will appear that shown in Figure 4-42:
Figure 4-42 Thwarted DoS Host Table
This page shows Host IP Address and Host MAC Address for each host blocked by the router.
¾
¾
Host IP Address- The IP address that blocked by DoS are displayed here.
Host MAC Address - The MAC address that blocked by DoS are displayed here.
To update this page and to show the current blocked host, click on the Refresh button.
Click the Clear All button to clear all displayed entries. After the table is empty the blocked host
will regain the capability to access Internet.
Click the Return button to return to the Advanced Security page
4.9 Static Routing
A static route is a pre-determined path that network information must travel to reach a specific
host or network. To add or delete a route, work in the area under the Static Routing page (shown
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 4-43 Static Routing
To add static routing entries:
2. Enter the following data:
¾
¾
¾
Destination IP Address - The Destination IP Address is the address of the network or host
that you want to assign to a static route.
Subnet Mask - The Subnet Mask determines which portion of an IP Address is the network
portion, and which portion is the host portion.
Gateway - This is the IP Address of the gateway device that allows for contact between the
router and the network or host.
3. Select Enabled or Disabled for this entry on the Status pull-down list.
4. Click the Save button to save it.
Figure 4-44 Add or Modify a Static Route Entry
To modify or delete an existing entry:
1. Click the Modify in the entry you want to modify. If you want to delete the entry, click the
Delete.
2. Modify the information.
3. Click the Save button.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Click the Enable All button to make all entries enabled.
Click the Disabled All button to make all entries disabled.
Click the Delete All button to delete all entries
4.10 IP QoS
IP QoS helps you to arrange the network resources more reasonably. This function can
guarantee the minimum bandwidth or limit the maximum bandwidth for the specified IP address(or
IP range) to make full use of the supplied bandwidth. You can configure the IP QoS on this page,
shown as in Figure 4-45.
Figure 4-45
¾
¾
Enable IP QoS – Enable or disable IP QoS function. You can enable this function for better
performance and experience with online games and other interactive applications such as
VoIP. The following IP Range QoS configuration won’t be effective unless it is enabled.
Choose Bandwidth Type – Specifies your network connection type. Here you can select
either ADSL or Other.
•
•
ADSL – Select if you are using a dial-up connection.
Other – Select if you are using other connection types.
¾
Bandwidth Apply – Specifies the bandwidth you get from your ISP. If you are not clear about
56
Download from Www.Somanuals.com. All Manuals Search And Download.
that, please contact with your ISP for help.
¾
¾
IP Range – Specifies the IP range of this entry.
Mode – There are 2 types of mode: Minimum Bandwidth Guarantee and Maximum
Bandwidth Limit.
¾
¾
¾
Bandwidth – Specifies the bandwidth you want to supply to this entry.
Description – Description of this entry.
Enable – Enable this entry. This entry won’t be effective unless you check the Enable box.
Click the Delete button to delete single entry.
Click the Delete All button to delete all entries.
Click the Save button to save all configuration.
For example, we assume that PC A, B, C are sharing the Internet with 2Mbps bandwidth through
one router. PC A is often for VoIP or online games, to guarantee its better performance without
interference from PC B and C, you can specify the minimum bandwidth for PC A such as
100Kbps.
Note:
)
1. The conversion relation of bandwidth: 1 Mbps = 1000Kbps.
2. Please choose the Network Connection Type and set the bandwidth according to your
Network. If you are not clear about that, please contact with your ISP for help.
3. IP address range for different entries could not have intersection with each other.
4. After the configuration, click the Save button for the change to take effect.
4.11IP & MAC Binding Setting
Figure 4-46 the IP & MAC Binding menu
Setting and ARP List. Click any of them, and you will be able to scan or configure the
corresponding function. The detailed explanations for each submenu are provided below.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
4.11.1 Binding Setting
This page displays the IP & MAC Binding Setting table; you can operate it in accord with your
Figure 4-47 IP & MAC Binding Setting
• MAC Address - The MAC address of the controlled computer in the LAN.
• IP Address - The assigned IP address of the controlled computer in the LAN.
• Bind - Whether or not enable the arp binding.
• Modify - Edit or delete item.
When you want to add or modify an IP & MAC Binding entry, you can click the Add New button
or Modify button, and then you will go to the next page. This page is used for adding or
Figure 4-48 IP & MAC Binding Setting (Add & Modify)
To add IP & MAC Binding entries:
1. Click the Add New... button.
2. Enter the MAC Address and IP Address.
3. Select the Bind checkbox.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Click the Save button to save it.
To modify or delete an existing entry:
1. Find the desired entry in the table.
2. Click Modify or Delete as desired on the Modify column.
To find an existing entry:
2. Enter the MAC Address or IP Address.
Figure 4-49 Find IP & MAC Binding Entry
Click the Enable All button to make all entries enabled.
Click the Delete All button to delete all entries.
4.11.2 ARP List
To manage the computer, you could observe the computers in the LAN by checking the
relationship of MAC address and IP address on the ARP list, and you could configure the items on
the ARP list also. This page displays the ARP List; it shows all the existing IP & MAC Binding
Figure 4-50 ARP List
59
Download from Www.Somanuals.com. All Manuals Search And Download.
• MAC Address - The MAC address of the controlled computer in the LAN.
• IP Address - The assigned IP address of the controlled computer in the LAN.
• Status - Enabled or Disabled of the MAC address and IP address binding.
• Configure - Load or delete item.
• Load - Load the item to the IP & MAC Binding list.
• Delete - Delete the item.
Click the Bind All button to bind all the current items, available after enable.
Click the Load All button to load all items to the IP & MAC Binding list.
Click the Refresh button to refresh all items.
Note:
)
An item could not be loaded to the IP & MAC Binding list if the IP address of the item has been
loaded before. Error warning will prompt as well. Likewise, "Load All" only loads the items without
interference to the IP & MAC Binding list.
4.12DDNS
The router offers a Dynamic Domain Name System (DDNS) feature. DDNS lets you assign a fixed
host and domain name to a dynamic Internet IP Address. It is useful when you are hosting your
own website, FTP server, or other server behind the router. Before using this feature, you need to
www.comexe.cn. The Dynamic DNS client service provider will give you a password or key.
To set up for DDNS, follow these instructions:
4.12.1 Dyndns.org DDNS
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 4-51 Dyndns.org DDNS Settings
To set up for DDNS, follow these instructions:
1. Type the domain names your dynamic DNS service provider gave.
2. Type the User Name for your DDNS account.
3. Type the Password for your DDNS account.
4. Click the Login button to login to the DDNS service.
¾
Connection Status -The status of the DDNS service connection is displayed here.
Click Logout to logout of the DDNS service.
4.12.2 Oray.net DDNS
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 4-52 Oray.net DDNS Settings
To set up for DDNS, follow these instructions:
1. Type the User Name for your DDNS account.
2. Type the Password for your DDNS account.
3. Click the Login button to login the DDNS service.
¾
¾
Connection Status - The status of the DDNS service connection is displayed here.
Domain Name - The domain names are displayed here.
Click Logout to logout the DDNS service.
4.12.3 Comexe.cn DDNS
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 4-53 Comexe.cn DDNS Settings
To set up for DDNS, follow these instructions:
1. Type the domain names your dynamic DNS service provider gave.
2. Type the User Name for your DDNS account.
3. Type the Password for your DDNS account.
4. Click the Login button to login to the DDNS service.
¾
Connection Status -The status of the DDNS service connection is displayed here.
Click Logout to logout of the DDNS service.
4.13System Tools
Figure 4-54 The System Tools menu
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Factory Defaults, Backup & Restore, Reboot, Password, Syslog, Remote Management and
Statistics. Click any of them, and you will be able to configure the corresponding function. The
detailed explanations for each submenu are provided below.
4.13.1 Time
You can set time manually or get GMT from the Internet for the router on this page (shown in
Figure 4-55 Time settings
¾
¾
¾
Time Zone - Select your local time zone from this pull down list.
Date - Enter your local date in MM/DD/YY into the right blanks.
Time - Enter your local time in HH/MM/SS into the right blanks.
Time setting follows these steps below:
1. Select your local time zone.
2. Enter date and time in the right blanks
3. Click Save.
Click the Get GMT button to get GMT time from Internet if you have connected to Internet.
If you’re using Daylight saving time, please follow the steps below.
1. Select using daylight saving time.
2. Enter daylight saving beginning time and end time in the right blanks.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Click Save.
Note:
)
1. This setting will be used for some time-based functions such as firewall. You must specify
your time zone once you login to the router successfully, if not, the time limited on these
functions will not take effect.
2. The time will be lost if the router is turned off.
3. The router will obtain GMT automatically from Internet if it has already connected to Internet.
4.13.2 Firmware
router up-to-date.
Figure 4-56 Firmware Upgrade
experiencing difficulties, there is no need to upgrade firmware, unless the new firmware supports
a new feature you need.
Note:
)
When you upgrade the router's firmware, you will lose current configuration settings, so make
sure you backup the router’s settings before you upgrade its firmware.
To upgrade the router's firmware, follow these instructions:
2. Click Browse to view the folders and select the downloaded file.
3. Click the Upgrade button.
¾
¾
Firmware Version - Displays the current firmware version.
Hardware Version - Displays the current hardware version. The hardware version of the
upgrade file must accord with the current hardware version.
Note:
)
65
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Do not turn off the router or press the Reset button while the firmware is being upgraded.
2. The router will reboot after the Upgrading has been finished.
4.13.3 Factory Defaults
Figure 4-57 Restore Factory Default
Click the Restore button to reset all configuration settings to their default values.
•
•
•
•
The default User Name: admin
The default Password: admin
The default IP Address: 192.168.1.1
The default Subnet Mask: 255.255.255.0
Note: Any settings you have saved will be lost when the default settings are restored.
)
4.13.4 Backup & Restore
restore the configuration file you saved before.
Figure 4-58 Backup and Restore Configuration
¾
¾
Click the Backup button to save all configuration settings as a backup file in your local
computer.
To restore the router's configuration, follow these instructions:
•
Click the Browse button to select the backup file which you want to restore.
•
Click the Restore button.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Note:
)
The current configuration will be covered with the uploading configuration file. The restoration
process lasts for 20 seconds and the router will restart automatically. Keep the router on during
the restoring process, to prevent any damage.
4.13.5 Reboot
Figure 4-59Reboot the router
Click the Reboot button to reboot the router.
Some settings of the router will take effect only after rebooting, which include:
•
•
•
•
•
•
•
Change LAN IP Address. (System will reboot automatically)
MAC Clone (system will reboot automatically)
DHCP service function.
Static address assignment of DHCP server.
Web Service Port of the router.
Upgrade the firmware of the router (system will reboot automatically).
Restore the router's settings to factory default (system will reboot automatically).
4.13.6 Password
password of the router.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 4-60 Password
It is recommended strongly that you change the factory default user name and password of the
router. All users who try to access the router's Web-based utility or Quick Setup will be prompted
for the router's user name and password.
Note:
)
The new user name and password must not exceed 14 characters in length and must not include
any spaces. Enter the new Password twice to confirm it.
Click the Save button when finished.
Click the Clear All button to clear all.
4.13.7 Syslog
Figure 4-61 System Log
The router can keep logs of all traffic. You can query the logs to find what happened to the router.
Click the Refresh button to refresh the logs.
Click the Clear All button to clear all the logs.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
4.13.8 Remote Management
feature allows you to manage your Router from a remote location, via the Internet.
Figure 4-62 Remote Management
¾
Web Management Port - Web browser access normally uses the standard HTTP service
port 80. This router’s default remote management Web port number is 80. For greater
security, you can change the remote management Web interface to a custom port by
entering that number in this box provided. Choose a number between 1024 and 65534, but
do not use the number of any common service port.
¾
Remote Management IP Address - This is the current address you will use when
accessing your router from the Internet. The default IP Address is 0.0.0.0. It means this
function is disabled. To enable this function, change the default IP Address to another IP
Address as desired.
To access the router, you will type your router's WAN IP Address into your browser's Address
(in IE) or Location (in Navigator) box, followed by a colon and the custom port number. For
example, if your Router's WAN address is 202.96.12.8 and you use port number 8080, enter in
successfully entering the password, you will be able to access the router's Web-based utility.
Note: Be sure to change the router’s default password to a very secure password.
)
4.13.9 Statistics
including total traffic and traffic of the last Packets Statistic interval seconds.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 4-63 Statistics
¾
¾
¾
Current Statistics Status - Enable or Disable. The default value is disabled. To enable, click
the Enable button. If disabled, the function of DoS protection in Security settings will be
ineffective.
Packets Statistics Interval - The default value is 10. Select a value between 5 and 60
seconds in the pull-down list. The Packets Statistic interval indicates the time section of the
packets statistic.
Sorted Rules - Here displays sort as desired.
Statistics Table:
IP Address
The IP Address displayed with statistics
Packets The total amount of packets received and transmitted by the router.
Total
Bytes
The total amount of bytes received and transmitted by the router.
The total amount of packets received and transmitted in the last Packets
Current
Packets
Statistic interval seconds.
The total amount of bytes received and transmitted in the last Packets
Bytes
Statistic interval seconds.
ICMP
Tx
The total amount of the ICMP packets transmitted to WAN in the last
Packets Statistic interval seconds.
UDP
Tx
The total amount of the UDP packets transmitted to WAN in the last
Packets Statistic interval seconds.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
TCP
SYN
Tx
The total amount of the TCP SYN packets transmitted to WAN in the last
Packets Statistic interval seconds.
Click the Save button to save the Packets Statistic interval value.
Click the Auto-refresh checkbox to refresh automatically.
Click the Refresh button to refresh immediately.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: FAQ
1. How do I configure the router to access Internet by ADSL users?
1) First, configure the ADSL Modem configured in RFC1483 bridge model.
2) Connect the Ethernet cable from your ADSL Modem to the WAN port on the router. The
telephone cord plugs into the Line port of the ADSL Modem.
3) Login to the router, click the “Network” menu on the left of your browser, and click "WAN"
submenu. On the WAN page, select “PPPoE” for WAN Connection Type. Type user
name in the “User Name” field and password in the “Password” field, finish by clicking
“Connect”.
Figure A-1 PPPoE Connection Type
4) If your ADSL lease is in “pay-according-time” mode, select “Connect on Demand” or
“Connect Manually” for Internet connection mode. Type an appropriate number for “Max
Idle Time” to avoid wasting paid time. Otherwise, you can select “Auto-connecting” for
Internet connection mode.
Figure A-2 PPPoE Connection Mode
Note:
)
i. Sometimes the connection cannot be disconnected although you specify a time to Max Idle
Time, since some applications is visiting the Internet continually in the background.
ii. If you are a Cable user, please configure the router following the above steps.
2. How do I configure the router to access Internet by Ethernet users?
72
Download from Www.Somanuals.com. All Manuals Search And Download.
1) Login to the router, click the “Network” menu on the left of your browser, and click "WAN"
submenu. On the WAN page, select “Dynamic IP” for "WAN Connection Type", finish by
clicking “Save”.
2) Some ISPs require that you register the MAC Address of your adapter, which is
connected to your cable/DSL Modem during installation. If your ISP requires MAC
register, login to the router and click the "Network" menu link on the left of your browser,
and then click "MAC Clone" submenu link. On the "MAC Clone" page, if your PC’s MAC
address is proper MAC address, click the "Clone MAC Address" button and your PC’s
MAC address will fill in the "WAN MAC Address" field. Or else, type the MAC Address
into the "WAN MAC Address" field. The format for the MAC Address is
XX-XX-XX-XX-XX-XX. Then click the "Save" button. It will take effect after rebooting.
Figure A-3 MAC Clone
3. I want to use Netmeeting, what do I need to do?
1) If you start a Netmeeting as a host, no configuration is needed but entering the invitee’s
IP address.
2) If you start a Netmeeting as an invitee, you need to configure Virtual Server or DMZ Host
first.
3) How to configure Virtual Server: Login to the router, click the “Forwarding” menu on the
left of your browser, and click "Virtual Servers" submenu. On the "Virtual Server" page,
click Add New, then on the “Add or Modify a Virtual Server” page, enter “1720” into the
blank behind the “Service Port”, and your IP address behind the IP Address, assuming
192.168.1.169 for an example, remember to “Enable” and “Save”.
Figure A-4 Virtual Servers
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure A-5 Add or Modify a Virtual server Entry
Note:
)
Your opposite side should call your WAN IP, which is displayed on the “Status” page.
4) How to enable DMZ Host: Login to the router, click the “Forwarding” menu on the left of
your browser, and click "DMZ" submenu. On the "DMZ" page, click “Enable” radio and
type your IP address into the “DMZ Host IP Address” field, using 192.168.1.169 as an
example, remember to click the "Save” button.
Figure A-6 DMZ
4. I want to build a WEB Server on the LAN, what should I do?
1) Because the WEB Server port 80 will interfere with the WEB management port 80 on the
router, you must change the WEB management port number to avoid interference.
2) To change the WEB management port number: Login to the router, click the “Security”
menu on the left of your browser, and click "Remote Management" submenu. On the
"Remote Management" page, type a port number except 80, such as 88, into the "Web
Management Port" field. Click “Save” and reboot the router.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure A-7 Remote Management
Note:
)
If the above configuration takes effect, to configure to the router by typing http://192.168.1.1:88
(the router’s LAN IP address: Web Management Port) in the address field of the Web browser.
3) Login to the router, click the “Forwarding” menu on the left of your browser, and click the
"Virtual Servers" submenu. On the "Virtual Server" page, click Add New, then on the
“Add or Modify a Virtual Server” page, enter “80” into the blank behind the “Service Port”,
and your IP address behind the IP Address, assuming 192.168.1.188 for an example,
remember to “Enable” and “Save”.
Figure A-8 Virtual Servers
Figure A-9 Add or Modify a Virtual server Entry
5. The wireless stations cannot connect to the router.
1) Make sure the "Wireless Router Radio" is enabled.
2) Make sure that the wireless stations' SSID accord with the router's SSID.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B: Configuring the PCs
In this section, we’ll introduce how to install and configure the TCP/IP correctly in Windows XP.
First make sure your Ethernet Adapter is working, refer to the adapter’s manual if necessary.
1. Configure TCP/IP component
1) On the Windows taskbar, click the Start button, and then click Control Panel.
2) Click the Network and Internet Connections icon, and then click on the Network
Connections tab in the appearing window.
3) Right click the icon that showed below, select Properties on the prompt page.
Figure 0-1
4) In the prompt page that showed below, double click on the Internet Protocol (TCP/IP).
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 0-2
5) The following TCP/IP Properties window will display and the IP Address tab is open on
this window by default.
Now you have two ways to configure the TCP/IP protocol below:
¾ Setting IP address automatically
Select Obtain an IP address automatically, Choose Obtain DNS server automatically, as
shown in the Figure below:
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 0-3
)Note: For Windows 98 OS or before, the PC and router may need to be restarted.
¾ Setting IP address manually
1
2
Select Use the following IP address radio button. And the following items available
If the router's LAN IP address is 192.168.1.1, specify the IP address as 192.168.1.x (x is
from 2 to 254), and the Subnet mask as 255.255.255.0.
3
4
Type the router’s LAN IP address (the default IP is 192.168.1.1) into the Default gateway
field.
Select Use the following DNS server addresses. In the Preferred DNS Server field you
can enter the same value as the Default gateway or type the local DNS server IP address.
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Now:
Click OK to keep your settings.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C: Specifications
General
Standards
Protocols
Ports
IEEE 802.3, 802.3u, 802.11b and 802.11g
TCP/IP, PPPoE, DHCP, ICMP, NAT, SNTP
One 10/100M Auto-Negotiation WAN RJ45 port, Four 10/100M
Auto-Negotiation LAN RJ45 ports supporting Auto MDI/MDIX
Cabling Type
10BASE-T: UTP category 3, 4, 5 cable (maximum 100m)
EIA/TIA-568 100Ω STP (maximum 100m)
100BASE-TX: UTP category 5, 5e cable (maximum 100m)
EIA/TIA-568 100Ω STP (maximum 100m)
54/48/36/24/18/12/9/6Mbps or 11/5.5/3/2/1Mbps
Power, SYS, WLAN, WAN, 1-4
Radio Data Rate
LEDs
Safety & Emissions
FCC, CE
Environmental and Physical
Operating Temp.
0℃~40℃ (32℉~104℉)
10% - 90% RH, Non-condensing
Operating Humidity
Dimensions (W×D×H) 6.9×4.4×1.2 in. (174×111×30 mm) (without antenna)
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D: Glossary
¾
2x to 3x eXtended Range™ WLAN Transmission Technology - The WLAN device with 2x
to 3x eXtended Range™ WLAN transmission technology make its sensitivity up to 105 dB,
which gives users the ability to have robust, longer-range wireless connections. With this
range-enhancing technology, a 2x to 3x eXtended Range™ based client and access point can
maintain a connection at as much as three times the transmission distance of traditional
802.11b and 802.11g products, for a coverage area that is up to nine times greater. A
traditional 802.11b and 802.11g product transmission distance is about 300m, a 2x to 3x
eXtended Range™ based client and access point can maintain a connection transmission
distance may be up to 830m.
¾
¾
802.11b - The 802.11b standard specifies a wireless networking at 11 Mbps using
direct-sequence spread-spectrum (DSSS) technology and operating in the unlicensed radio
spectrum at 2.4GHz, and WEP encryption for security. 802.11b networks are also referred to
as Wi-Fi networks.
802.11g - specification for wireless networking at 54 Mbps using direct-sequence
spread-spectrum (DSSS) technology, using OFDM modulation and operating in the
unlicensed radio spectrum at 2.4GHz, and backward compatibility with IEEE 802.11b devices,
and WEP encryption for security.
¾
¾
¾
¾
DDNS (Dynamic Domain Name System) - The capability of assigning a fixed host and
domain name to a dynamic Internet IP Address.
DHCP (Dynamic Host Configuration Protocol) - A protocol that automatically configure the
TCP/IP parameters for the all the PC(s) that are connected to a DHCP server.
DMZ (Demilitarized Zone) - A Demilitarized Zone allows one local host to be exposed to the
Internet for a special-purpose service such as Internet gaming or videoconferencing.
DNS (Domain Name System) – An Internet Service that translates the names of websites into
IP addresses.
¾
¾
Domain Name - A descriptive name for an address or group of addresses on the Internet.
DoS (Denial of Service) - A hacker attack designed to prevent your computer or network from
operating or communicating.
¾
DSL (Digital Subscriber Line) - A technology that allows data to be sent or received over
existing traditional phone lines.
¾
¾
ISP (Internet Service Provider) - A company that provides access to the Internet.
MTU (Maximum Transmission Unit) - The size in bytes of the largest packet that can be
82
Download from Www.Somanuals.com. All Manuals Search And Download.
transmitted.
¾
¾
¾
NAT (Network Address Translation) - NAT technology translates IP addresses of a local area
network to a different IP address for the Internet.
PPPoE (Point to Point Protocol over Ethernet) - PPPoE is a protocol for connecting remote
hosts to the Internet over an always-on connection by simulating a dial-up connection.
SSID - A Service Set Identification is a thirty-two character (maximum) alphanumeric key
identifying a wireless local area network. For the wireless devices in a network to
communicate with each other, all devices must be configured with the same SSID. This is
typically the configuration parameter for a wireless PC card. It corresponds to the ESSID in
the wireless Access Point and to the wireless network name.
¾
¾
WEP (Wired Equivalent Privacy) - A data privacy mechanism based on a 64-bit or 128-bit or
152-bit shared key algorithm, as described in the IEEE 802.11 standard.
Wi-Fi - A trade name for the 802.11b wireless networking standard, given by the Wireless
group promoting interoperability among 802.11b devices.
¾
WLAN (Wireless Local Area Network) - A group of computers and associated devices
communicate with each other wirelessly, which network serving users are limited in a local
area.
83
Download from Www.Somanuals.com. All Manuals Search And Download.
|