TP Link Network Router 100 1910010798 User Manual

TL-WA750RE  
150Mbps Universal WiFi Range Extender  
REV 1.0.0  
1910010798  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FCC STATEMENT  
This equipment has been tested and found to comply with the limits for a Class B digital device,  
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection  
against harmful interference in a residential installation. This equipment generates, uses and can  
radiate radio frequency energy and, if not installed and used in accordance with the instructions,  
may cause harmful interference to radio communications. However, there is no guarantee that  
interference will not occur in a particular installation. If this equipment does cause harmful  
interference to radio or television reception, which can be determined by turning the equipment off  
and on, the user is encouraged to try to correct the interference by one or more of the following  
measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver  
is connected.  
Consult the dealer or an experienced radio/ TV technician for help.  
This device complies with part 15 of the FCC Rules. Operation is subject to the following two  
conditions:  
1) This device may not cause harmful interference.  
2) This device must accept any interference received, including interference that may  
cause undesired operation.  
Any changes or modifications not expressly approved by the party responsible for compliance  
could void the user’s authority to operate the equipment.  
Note: The manufacturer is not responsible for any radio or tv interference caused by unauthorized  
modifications to this equipment. Such modifications could void the user’s authority to operate the  
equipment.  
FCC RF Radiation Exposure Statement  
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled  
environment. This device and its antenna must not be co-located or operating in conjunction with  
any other antenna or transmitter.  
“To comply with FCC RF exposure compliance requirements, this grant is applicable to only  
Mobile Configurations. The antennas used for this transmitter must be installed to provide a  
separation distance of at least 20 cm from all persons and must not be co-located or operating in  
conjunction with any other antenna or transmitter.”  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CE Mark Warning  
This is a class B product. In a domestic environment, this product may cause radio interference, in  
which case the user may be required to take adequate measures.  
This device has been designed to operate with the antennas listed below, and having a maximum  
gain of 3 dBi. Antennas not included in this list or having a gain greater than 3 dBi are strictly  
prohibited for use with this device. The required antenna impedance is 50 ohms.  
To reduce potential radio interference to other users, the antenna type and its gain should be so  
chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for  
successful communication.  
Canadian Compliance Statement  
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject  
to the following two conditions:  
(1)This device may not cause interference, and  
(2)This device must accept any interference, including interference that may cause undesired  
operation of the device.  
Cet appareil est conforme aux norms CNR exemptes de licence d’Industrie Canada. Le  
fonctionnement est soumis aux deux conditions suivantes:  
(1)cet appareil ne doit pas provoquer d’interférences et  
(2)cet appareil doit accepter toute interférence, y compris celles susceptibles de provoquer un  
fonctionnement non souhaité de l’appareil.  
Industry Canada Statement  
Complies with the Canadian ICES-003 Class B specifications.  
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.  
This device complies with RSS 210 of Industry Canada. This Class B device meets all the  
requirements of the Canadian interference-causing equipment regulations.  
Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le  
matériel brouilleur du Canada.  
Korea Warning Statements  
당해 무선설비는 운용중 전파혼신 가능성이 있음.  
NCC Notice & BSMI Notice  
注意!  
依據 低功率電波輻射性電機管理辦法  
第十二條 經型式認證合格之低功率射頻電機,費經許可,公司、商號或使用者均不得擅自變更頻  
率、加大功率或變更原設計之特性或功能。  
Download from Www.Somanuals.com. All Manuals Search And Download.  
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通行;經發現有干擾現象時,應立  
即停用,并改善至無干擾時方得繼續使用。前項合法通信,指依電信規定作業之無線電信。低功率  
射頻電機需忍受合法通信或工業、科學以及醫療用電波輻射性電機設備之干擾。  
安全諮詢及注意事項  
請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。  
清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。  
注意防潮,請勿將水或其他液體潑灑到本產品上。   
插槽與開口供通風使用,以確保本產品的操作可靠並防止過熱,請勿堵塞或覆蓋開口。  
請勿將本產品置放於靠近熱源的地方。除非有正常的通風,否則不可放在密閉位置中。  
請不要私自打開機殼,不要嘗試自行維修本產品,請由授權的專業人士進行此項工作。  
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам  
нормативних документів та вимогам, що передбачені чинними законодавчими актами  
України.  
Safety Information  
When product has power button, the power button is one of the way to shut off the product;  
when there is no power button, the only way to completely shut off power is to disconnect the  
product or the power adapter from the power source.  
Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock  
and voiding the limited warranty. If you need service, please contact us.  
Avoid water and wet locations.  
This product can be used in the following countries:  
AT  
ES  
LT  
BG  
FI  
BY  
FR  
MT  
SK  
CA  
GB  
NL  
TR  
CZ  
GR  
NO  
UA  
DE  
HU  
PL  
DK  
IE  
EE  
IT  
LV  
SE  
PT  
RO  
RU  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TP-LINK TECHNOLOGIES CO., LTD  
DECLARATION OF CONFORMITY  
For the following equipment:  
Product Description: 150Mbps Universal WiFi Range Extender  
Model No.: TL-WA750RE  
Trademark: TP-LINK  
We declare under our own responsibility that the above products satisfy all the technical  
regulations applicable to the product within the scope of Council Directives:  
Directives 1999/5/EC, Directives 2004/108/EC, Directives 2006/95/EC, Directives 1999/519/EC,  
Directives 2011/65/EU  
The above product is in conformity with the following standards or other normative documents  
ETSI EN 300 328 V1.7.1: 2006  
ETSI EN 301 489-1 V1.9.2:2011& ETSI EN 301 489-17 V2.1.1:2009  
EN 55022:2010  
EN 55024:2010  
EN 61000-3-2:2006+A1:2009+A2:2009  
EN 61000-3-3:2008  
EN60950-1:2006+A112009+A1:2010+A12:2011  
EN62311:2008  
The product carries the CE Mark:  
Person responsible for marking this declaration:  
Yang Hongliang  
Product Manager of International Business  
Date of Issue: 2013  
TP-LINK TECHNOLOGIES CO., LTD.  
Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park,  
Shennan Rd, Nanshan, Shenzhen, China  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTENTS  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TL-WA750RE 150Mbps Universal WiFi Range Extender User Guide  
Package Contents  
The following items should be found in your package:  
TL-WA750RE 150Mbps Universal WiFi Range Extender  
Ethernet Cable  
Quick Installation Guide  
Resource CD for TL-WA750RE 150Mbps Universal WiFi Range Extender, including only this  
User Guide.  
Note:  
Make sure that the package contains the above items. If any of the listed items is damaged or  
missing, please contact your distributor.  
Conventions  
The Range Extender, the Device or TL-WA750RE mentioned in this User guide stands for  
TL-WA750RE 150Mbps Universal WiFi Range Extender without any explanations.  
Parameters provided in the pictures are just references for setting up the product, which may differ  
from the actual situation. You can set the parameters according to your demand.  
The power plug may differ from the picture illustrated in this UG due to different regional power  
specifications. Here we just take that of EU version for example.  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
TL-WA750RE 150Mbps Universal WiFi Range Extender User Guide  
Chapter 1 Introduction  
1.1 Product Overview  
The TL-WA750RE 150Mbps Universal WiFi Range Extender is dedicated to Small Office/Home  
Office (SOHO) wireless network solutions. It will enlarge your existing wireless network and  
mobility within your wireless network while also allowing you to connect a wired device to a  
wireless environment. Increased mobility and the absence of cabling will be beneficial for your  
network.  
With using IEEE 802.11n wireless technology, this device can transmit wireless data at the rate of  
up to 150Mbps. With multiple protection measures, including wireless LAN 64/128/152-bit WEP  
encryption, Wi-Fi protected Access (WPA2-PSK, WPA-PSK), the TL-WA750RE 150Mbps  
Universal WiFi Range Extender delivers complete data privacy.  
It supports an easy wireless connection to the root AP (equipped with WPS/QSS button) by  
pressing the RE button on the front panel. It also supports an easy, web-based setup for  
installation and management. Even though you may not be familiar with the Range Extender, you  
can easily configure it with the help of this Guide. Before installing the Range Extender, please  
look through this Guide to get the full information of the TL-WA750RE 150Mbps Universal WiFi  
Range Extender.  
1.2  
Main Features  
Applies IEEE 802.11n wireless technology  
Supports multiple encryption security types including: 64/128/152-bit WEP and  
WPA/WPA2-Personal  
Supports built-in DHCP server  
Supports two operating modes: Range Extender Mode 1 and Range Extender Mode 2  
Supports firmware upgrade  
Supports web management  
1.3 Appearance  
Figure 1-1  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
TL-WA750RE 150Mbps Universal WiFi Range Extender User Guide  
LED Explanation:  
Name  
Status  
On  
Indication  
The Range Extender is connected the router successfully.  
The Range Extender is connecting the router.  
The Range Extender is not connected any router yet.  
The Wireless function is disabled.  
RE  
Flashing  
Off  
Off  
Wireless  
Power  
Flashing  
Off  
The Wireless function is enabled.  
No Power.  
On  
Power on.  
Off  
There is no device linked to the corresponding port.  
There is a device linked to the corresponding port but no activity.  
There is an active device linked to the corresponding port.  
Ethernet  
On  
Flashing  
Off  
No signal at present.  
Signal  
Signal is transferring. And it also shows the current signal strength  
the range extender received from the root AP after successful  
connection.  
Strength  
Solid  
(1~5)  
Table 1-1  
(RANGE EXTENDER/WPS): If your Wireless router or AP supports WPS or QSS  
function, you can press the WPS or QSS button and then press the RANGE EXTENDER  
button to establish a secure connection between the Wireless router (or AP) and the Range  
Extender TL-WA750RE.  
RESET: This button is used to restore the Range Extender’s factory default settings.  
There are two ways to reset the Range Extender’s factory defaults:  
Method One: With the Range Extender powered on, use a pin to press and hold the RESET  
button (about 8 seconds) until the System LED becomes quick-flash from slow-flash. And  
then release the button and wait the Range Extender to reboot to its factory default settings.  
Method Two: Restore the default settings from “System Tools > Factory Defaults” of the  
Range Extender's Web-based management page.  
ETHERNET: One 10/100Mbps RJ45 Ethernet port used to add wireless connectivity to an  
Ethernet-enabled device such as Internet TV, DVR, Gaming console and so on. Please note  
that this port is not allowed to be connected with router or AP.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
TL-WA750RE 150Mbps Universal WiFi Range Extender User Guide  
Chapter 2 Hardware Installation  
2.1 Before You Begin  
Please read this User Guide carefully before installing and using the equipment. The operating  
distance range of your wireless connection can vary significantly depending on the physical  
position of the wireless devices. Factors that can weaken signals by getting in the way of your  
network’s radio waves are metal appliances or obstructions, and walls. Typical ranges vary based  
on the types of materials and background RF (radio frequency) noise in your home or office.  
In order to optimize the performance of TL-WA750RE, please follow the instructions below to  
achieve an ideal location (please make sure it is always within the wireless coverage of the  
wireless router).  
1)  
Half-way Between - Generally, the ideal location for TL-WA750RE is half-way between the  
Wireless router and Wireless Client. If the wireless signal is not satisfactory, you may place  
TL-WA750RE somewhat nearer to the Wireless router.  
2)  
3)  
No Obstacles and Spacious - Clear obstacles in the way between TL-WA750RE and  
Wireless router. It’s better to locate it in a spacious place, such as near the corridors.  
No Interference - Keep TL-WA750RE far away from wireless interference, which may come  
from electrical appliances that works in the same frequency band as TL-WA750RE, such as  
Blue tooth devices, cordless phones, microwave ovens, etc.  
4)  
3 Signal Lights - You can also find an ideal location via the signal lights on the front panel of  
TL-WA750RE. These lights show the strength of signal your range extender receives from  
the root AP. It's recommended that you choose a location where at least 3 signal lights light  
up, in order to guarantee a good performance.  
Note:  
TP-LINK recommends that you connect to the Range Extender when your home network  
connection is poor, or when you want a larger wireless coverage to eliminate “dead zones”. As in  
compliance with the wireless transmission protocol, all the Range Extender devices are set to  
work in half-duplex instead of full-duplex mode. In other words, the Range Extender has to  
process one-way communication between your root Wireless router (or AP) and the terminal  
clients; so the transmission time will be double-increased, while the speed will be decreased.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
TL-WA750RE 150Mbps Universal WiFi Range Extender User Guide  
2.2 Basic Requirements  
Place your Range Extender in a well-ventilated place far from direct sunlight, any heater or  
heating vent.  
Leave at least 2 inches (5cm) space around the device for heat dissipation.  
Turn off your Range Extender and unplug the power adapter in a lighting storm to avoid  
damage.  
Use Web browser, such as Microsoft Internet Explorer 5.0 or above, Netscape Navigator 6.0  
or above.  
Operating temperature of the Range Extender should be 0~40(32~104).  
Operating humidity of the Range Extender should be 10%~90%RH (Non-condensing).  
2.3 Connecting the Device  
Figure 2-1 Typical connection of TL-WA750RE  
To establish a typical connection of the Range Extender, please take the following steps:  
1. Connect the Cable/DSL modem to a Wireless router with an Ethernet cable.  
2. Plug your TL-WA750RE directly to a standard electrical wall socket, which is next to the  
Wireless router.  
3. Connect your Wireless Clients (such as notebook, pad, smart phone, etc.) to TL-WA750RE  
wirelessly. Or you can connect your PC to the sole LAN port of Range Extender via an  
Ethernet cable.  
4. Log in the web-based management page of TL-WA750RE and complete the configurations.  
configurations, as you need.) Through the web page configuration you can successfully  
connect TL-WA750RE to the wireless router.  
5. Adjust an ideal location for TL-WA750RE. (Please refer to Section 2.1 Before You Begin for  
detailed information about ideal location.)  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
TL-WA750RE 150Mbps Universal WiFi Range Extender User Guide  
Chapter 3 Quick Installation Guide  
This chapter will guide you to configure your PC to communicate with the Range Extender and to  
configure and manage the TL-WA750RE 150Mbps Universal WiFi Range Extender easily with a  
Web-based utility.  
With a Web-based utility, it is easy to configure and manage the TL-WA750RE 150Mbps Universal  
WiFi Range Extender. The Web-based utility can be used on any Windows, Macintosh or UNIX  
OS with a Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari.  
1. To access the configuration utility, open a web-browser and type in the domain name  
http://tplinkextender.net in the address field of the browser.  
Figure 3-1 Login to the Range Extender  
After a moment, a login window will appear as shown in Figure 3-2. Enter admin for the User  
Name and Password (both in lower case letters). Then click OK or press Enter.  
Figure 3-2 Login Windows  
Note:  
If the above screen does not prompt, it means that your web-browser has been set to a proxy. Go  
to Tools menu > Internet Options > Connections > LAN Settings, in the screen that appears,  
cancel the Using Proxy checkbox, and click OK to finish it.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
TL-WA750RE 150Mbps Universal WiFi Range Extender User Guide  
2. After successful login, there will pop up the Quick Setup Start page. Click Next to get the  
quick setup started.  
Figure 3-3 Quick Setup Start  
3. Figure 3-4 will appear for you to choose the region. Then click Next to continue.  
Figure 3-4 Quick Setup – Choose Region  
4. The device will detect the existing wireless networks. Please wait for a while.  
Figure 3-5 Quick Setup – Detect Existing Networks  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
TL-WA750RE 150Mbps Universal WiFi Range Extender User Guide  
5. A list of available wireless networks will appear. Check the box before the SSID of your  
desired network, and then click Next.  
Figure 3-6 Quick Setup – Available Wireless Networks  
Note:  
If you could not find your wireless network name (SSID) in the list, you can click  
to  
Rescan  
redetect it or tick the checkbox before "Set SSID and MAC Manually" to manually configure the  
wireless settings.  
6. Wireless Settings page will appear as shown in Figure 3-7. Please enter the Wireless  
Password of your selected target network and then click Next to continue.  
Figure 3-7 Quick Setup – Wireless Settings  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
TL-WA750RE 150Mbps Universal WiFi Range Extender User Guide  
7. Double-check your wireless setting and network setting on the page as shown in Figure 3-8. If  
verified, click Finish to complete the Quick Setup. If there is anything wrong, click Back to  
return the previous pages and reconfigure it.  
Figure 3-8 Quick Setup – Review Settings  
Note:  
1. It’s recommended to click the Export Settings button to save these settings as a txt file for  
your future reference.  
2. After you click Finish, there will pop up such a window as Figure 3-9, where please click OK  
and patiently wait about 2 minutes for the network connection.  
Figure 3-9 Quick Setup  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
TL-WA750RE 150Mbps Universal WiFi Range Extender User Guide  
Chapter 4 Configure the Device  
This Chapter describes how to configure your Range Extender via the web-based management  
page. The TL-WA750RE 150Mbps Universal WiFi Range Extender is easy to configure and  
manage with the Web-based (Internet Explorer, Netscape® Navigator, Firefox, Safari, Opera or  
Chrome) management page, which can be launched on any windows, Macintosh or UNIX OS with  
a web browser.  
After a successful login, you can configure and manage the device. There are eight main menus  
on the leftmost column of the web-based management page: Status, Quick Setup, WPS, Profile,  
Network, Wireless, DHCP and System Tools. Submenus will be available after clicking one of  
the main menus. On the right of the web-based management page are the detailed explanations  
and instructions for the corresponding page.  
4.1 Status  
Selecting Status will enable you to view the Range Extender’s current status and configuration, all  
of which are read-only.  
Figure 4-1 Status  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
TL-WA750RE 150Mbps Universal WiFi Range Extender User Guide  
Firmware Version - This field displays the current firmware version of the Range Extender.  
Hardware Version - This field displays the current hardware version of the Range Extender.  
Connection Status to Existing Network - This part shows you the current information of the  
root wireless network which the device is connecting to.  
Root Wireless Network Name (SSID) - It shows the name of the wireless network which  
your device is connecting to.  
Signal - It shows the root wireless network's signal strength that the device has received.  
Connection Status - It shows whether your device has been connected to a wireless  
network currently. "Connected" means the range extender have connected to a wireless  
network, while if it shows "disconnected", you can click "connect" to connect.  
Wired - This field displays the current settings or information for the Network.  
MAC Address - The physical address of the system, as seen from the Network -> LAN  
page.  
IP Address - The IP address of the wired LAN.  
Subnet Mask - The subnet mask associated with IP address.  
Wireless - This field displays basic information or status for wireless function.  
Operation Mode - Indicates the mode which the device is working on. "Disable" means  
the wireless radio has been turned off. You can configure it in the Wireless -> Wireless  
Settings page.  
Local Wireless Network Name (SSID) - The Device's wireless network name (also  
called SSID) which your PC or other device can be connected to.  
Channel - The current wireless channel in use.  
Mode - The current wireless mode which the Range Extender works on.  
Channel Width - The bandwidth of the wireless channel.  
Wireless Rate - It shows the current wireless rate between the range extender and your  
PC or other devices which are connected to it.  
Traffic Statistics - This field displays the Range Extender's traffic statistics.  
Sent (Bytes) - Traffic that counted in bytes has been sent out from wireless.  
Sent (Packets) - Traffic that counted in packets has been sent out from wireless.  
Received (Bytes) - Traffic that counted in bytes has been received from wireless.  
Received (Packets) - Traffic that counted in packets has been received from wireless.  
System Up Time - This filed displays the run time of the Range Extender since it’s powered  
on or reset.  
Click the Refresh button to get the latest status and settings of the device.  
4.2 Quick Setup  
4.3 WPS  
WPS (Wi-Fi Protected Setup) can help you to quickly and securely connect to a network. This  
section will guide you to add a new wireless device to an existing network quickly by WPS function.  
The WPS function can be configured on the page as shown in Figure 4-2.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
TL-WA750RE 150Mbps Universal WiFi Range Extender User Guide  
Figure 4-2 WPS - Enabled  
Operation Mode - Displays the current operation mode of the device.  
WPS Status - To enable or disable the WPS function here.  
Current PIN - The current value of the device's PIN is displayed here. The default PIN of the  
device can be found in the label or User Guide.  
Restore PIN - Restore the PIN of the device to its default.  
Gen New PIN - Click this button, and then you can get a new random value for the device's  
PIN. You can ensure the network security by generating a new PIN.  
Disable PIN of this device - WPS external registrar of entering this device's PIN can be  
disabled or enabled manually. If this device receives multiple failed attempts to authenticate  
an external Registrar, this function will be disabled automatically.  
Add device - You can add a new device to the existing network manually by clicking this  
button.  
To add a new device:  
If the wireless adapter supports WPS, you can establish a wireless connection between wireless  
adapter and device using either PBC (Push Button Configuration) method or PIN method.  
Note:  
To build a successful connection by WPS, you should also do the corresponding configuration of  
the network adapter for WPS function meanwhile. And as for the configuration of the network  
adapter, here takes the wireless adapter of our company for example.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
TL-WA750RE 150Mbps Universal WiFi Range Extender User Guide  
Method One: Push the button of the Range Extender and Wireless Adapter  
Step 1: Keep the “WPS Status” as Enabled and click the Add Device button in Figure 4-2, then  
the following screen will appear.  
Figure 4-3 Add A New Device  
Step 2: Choose “Press the button of the new device in two minutes” and click Connect.  
Step 3: For the configuration of the wireless adapter, please choose “Push the button on my  
access point or wireless router.” in the configuration utility of the WPS (as shown  
below), and click Connect.  
Figure 4-4 The WPS Configuration Screen of Wireless Adapter  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TL-WA750RE 150Mbps Universal WiFi Range Extender User Guide  
Step 4: Wait until the next screen appears. Click OK to complete the WPS configuration.  
Figure 4-5 The WPS Configuration Screen of Wireless Adapter  
Method Two: Enter the PIN into my Range Extender  
Step 1: Configure the wireless adapter. Please choose “Enter the PIN of this device into my  
access point or wireless adapter” in the configuration utility of the WPS (as shown  
below), and click Connect.  
Figure 4-6 The WPS Configuration Screen of wireless adapter  
Note:  
In this example, the default PIN code of this adapter is 19342306 as the above figure shows.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TL-WA750RE 150Mbps Universal WiFi Range Extender User Guide  
Step 2: Configure the router. Keep the default “WPS Status” as Enabled and click the Add device  
button in Figure 4-2, then the following screen will appear.  
Figure 4-7  
Step 3: Choose Enter the new device's PIN and enter the PIN code of the wireless adapter in  
the field behind PIN in the previous figure. Then click Connect.  
Figure 4-8  
Method Three: Enter the PIN from my Range Extender  
Step 1: Get the Current PIN code of the Range Extender in Figure 4-2 (each Range Extender has  
its unique PIN code. Here takes the PIN code 12345670 of this Range Extender for  
example).  
Step 2: For the configuration of the wireless adapter, please choose “Enter the PIN of my  
access point or wireless router” in the configuration utility of the WPS (as shown below),  
and enter the PIN code of the Range Extender into the PIN field. Then click Connect.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TL-WA750RE 150Mbps Universal WiFi Range Extender User Guide  
Figure 4-9 The WPS Configuration Screen of Wireless Adapter  
Note:  
The default PIN code of the Range Extender can be found in its label or the WPS configuration screen  
You will see the following screen when the new device has successfully connected to the network.  
Figure 4-10  
Note:  
1. The RE LED will be lighted on for about five minutes if the device has been successfully  
added to the network.  
2. The WPS function cannot be configured if the Wireless function of the Range Extender is  
disabled. Please make sure the Wireless function is enabled before configuring the WPS.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TL-WA750RE 150Mbps Universal WiFi Range Extender User Guide  
4.4 Profile  
Profile function can help you remember previously connected wireless networks.  
You can Edit, Delete or Add profiles in this page (as shown in Figure 4-11) for your convenient  
reconnection later on.  
Figure 4-11 Profile  
Choose - You can choose any one wireless network you want to connect to.  
Profile Name - The name you give to your wireless network(s). By default, it's the same as  
root SSID, but you can change it to any other names that you can easily remember and  
distinguish.  
Root SSID - the SSID (wireless network name) of your root device, a wireless router or AP.  
MAC - The physical address of your root AP, also called BSSID.  
Security Type - The security type of your root device.  
Modify - You can Edit or Delete the profile(s).  
Click Connect to connect the range extender to the wireless network that you have chosen in the  
profile list.  
Click Add to add a new profile to the list.  
Click Delete All to delete all the information in the profile list.  
To add a profile:  
1. Click Add in the Profiles list page as shown in Figure 4-11.  
2. Configure the required parameters (as shown in Figure 4-12), including name your profile, enter  
the SSID of your root device (a wireless router or AP) and its MAC address, select the security  
type of your root device and also enter the wireless password. Then click to Save your profile.  
Figure 4-12 Add or Modify the Profile  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
TL-WA750RE 150Mbps Universal WiFi Range Extender User Guide  
Profile Name - The name you give to your wireless networks. By default, it's the same as  
root SSID, but you can change it to any other names that you can easily remember and  
distinguish.  
Root SSID - The wireless network name of your root AP this profile will connect to.  
MAC of Root Device - The MAC of your root device this profile will connect to.  
Wireless Security - The security type of your root wireless networks this profile will refer  
to. Please make sure it's the same as the root AP's.  
Wireless Password - The wireless password of your root AP. Please make sure it's the  
same as your root AP.  
Click Save to save this profile in the profile list and go back to the Profile List page.  
Click Back to go back to the Profile List page, without saving any configuration on this page.  
3. After you’ve set and saved the profile, it will return to the profiles list page and display as in  
Figure 4-13 Add or Modify the Profile  
Click Edit to further edit the profile(s), or Delete to delete the profile(s).  
Click Connect to connect the range extender to the wireless network that you have chosen in  
the profiles list.  
Click Add to add a new profile to the list.  
Click Delete All to delete all the information in the profiles list.  
4.5 Network  
The Network option allows you to customize your local network manually by changing the default  
settings of the Range Extender.  
Figure 4-14 Network Menu  
Selecting Network > LAN will enable you to configure the IP parameters of Network on this page.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
TL-WA750RE 150Mbps Universal WiFi Range Extender User Guide  
Figure 4-15 LAN  
MAC Address - The physical address of the LAN port, as seen from the LAN. The value  
cannot be changed.  
Type - Several IP types are supported, including: (1) Static IP; (2) Smart IP (DHCP), and they  
are explained below.  
Static IP - In this type, you can configure IP Address/Gateway manually.  
Smart IP (DHCP) - In this type, if your Range Extender have connected to a router, your  
client will dynamically get an IP Address/Gateway from the router, otherwise the client  
will get a IP Address/Gateway in the same network as you set below. And this type is  
recommended.  
IP Address - Enter the IP address of your Range Extender in dotted-decimal notation (factory  
default setting is 192.168.0.254).  
Subnet Mask - An address code that determines the size of the network. Normally use  
255.255.255.0 as the subnet mask.  
Gateway - The gateway should be in the same subnet as your IP address.  
Note:  
1. If you are not familiar with the setting items in this page, it's strongly recommended to keep  
the provided default values. Otherwise it may result in lower wireless network performance or  
even function failure.  
2. If you choose Static IP, the domain name login function won't work, and you have to use the  
IP you set to log in the Range Extender's web based utility.  
4.6 Wireless  
The Wireless option, improving functionality and performance for wireless network, can help you  
make the Range Extender an ideal solution for your wireless network. Here you can create a  
wireless local area network just through a few settings. Wireless Settings is used for the  
configuration of some basic parameters of the Range Extender. Wireless Security provides three  
different security types to secure your data and thus provide greater security for your wireless  
network. MAC filtering allows you to control the access of wireless stations to the Range Extender.  
Wireless Advanced allows you to configure some advanced parameters for the Range Extender.  
Throughput Monitor helps to watch wireless throughput information Wireless statistics enables you  
to get detailed information about the current connected wireless stations.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
TL-WA750RE 150Mbps Universal WiFi Range Extender User Guide  
There are six submenus under the Wireless menu (shown in Figure 4-16): Wireless Settings,  
Wireless Security, Wireless MAC Filtering, Wireless Advanced, Wireless Statistics and  
Throughput Monitor. Click any of them, and you will be able to configure the corresponding  
function. The detailed explanations for each submenu are provided below.  
Figure 4-16 Wireless menu  
4.6.1 Wireless Settings  
Selecting Wireless > Wireless Settings will enable you to configure the basic settings for your  
wireless network on the screen below (Figure 4-17).This page allows you to configure the wireless  
mode for your device. Two operation modes are supported here, including Range Extender  
mode 1, and Range Extender mode 2. The only difference between these two modes is that  
Range Extender mode 1 has WDS disabled while Range Extender mode 2 has WDS enabled. In  
both modes, the Range Extender will relay data to an associated root AP. The range extender  
function is enabled meanwhile. The wireless repeater relays signal between its stations and the  
root AP for greater wireless range. Since the configurations are almost the same in either  
operation mode, here we just take that in Range Extender mode 1 for example.  
Figure 4-17 Wireless Settings  
Operation Mode - Two Operation Modes are supported, including Range Extender mode 1  
and Range Extender mode 2.  
Survey - Click this button, you can search the AP which runs in the current channel.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
TL-WA750RE 150Mbps Universal WiFi Range Extender User Guide  
Wireless Name of Root AP - The SSID of the AP your device is going to connect to as a  
client. You can also use the search function to select the SSID to join.  
MAC Address of Root AP - The BSSID of the AP your device is going to connect to as a  
client. You can also use the search function to select the BSSID to join.  
Region - Select your region from the drop-down list. This field specifies the region where the  
wireless function of this device can be used. It may be illegal to use the wireless function of  
this device in a region while you chose a different region in the drop-down list. If your country  
or region is not listed, please contact your local government agency for assistance.  
Note:  
The default region is United Kingdom. When you select your local region from the pull-down  
list, the dialog shown in Figure appears below. Click OK.  
Note Dialog  
Note:  
Restricted by local law regulations, version for North America does not have region selection  
option.  
Mode - If all of the wireless devices connected with this device can connect in the same  
transmission mode (eg. 802.11b), you can choose "Only" mode (eg. 11b only). If you have  
some devices that use a different transmission mode, choose the appropriate "Mixed" mode.  
Channel Width - The bandwidth of the wireless channel.  
Max Wireless Rate - You can limit the maximum wireless rate of the device through this field.  
To apply any settings you have altered on the page, please click the Save button, and then you  
will be reminded to reboot the device.  
4.6.2 Wireless Security  
Selecting Wireless > Wireless Security will enable you to configure wireless security for your  
wireless network to protect your data from intruders. The Range Extender provides two security  
types: WEP and WPA/WPA2-Personal. Wireless security can be set on the following screens.  
Since the configurations are almost the same in either operation mode, here we just take that in  
Range Extender mode 1 for example.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
TL-WA750RE 150Mbps Universal WiFi Range Extender User Guide  
Figure 4-18 Wireless Security  
Operation Mode - Shows the current operation mode.  
Disable Security - Check this box radio button to disable wireless security. If disabled, the  
wireless stations will be able to connect this device without encryption. It is strongly  
recommended that you choose one of the security types to enable security.  
WPA/ WPA2-Personal - Select WPA based on pre-shared key.  
Version - You can select one of following versions.  
1) Automatic - Select WPA-PSK or WPA2-PSK automatically based on the wireless  
station's capability and request.  
2) WPA-PSK - Pre-shared key of WPA.  
3) WPA2-PSK - Pre-shared key of WPA2.  
Encryption - When you select WPA-PSK or WPA2-PSK for Authentication Type, you  
can select Automatic, TKIP or AES as Encryption.  
Wireless Password - Enter a passphrase here.  
Group Key Update Period - Specify the group key update interval in seconds. The value  
can be either 0 or at least 30. Enter 0 to disable the update.  
WEP - Select 802.11 WEP security.  
Type - You can select one of following types.  
1) Automatic - Select Shared Key or Open System authentication type automatically  
based on the wireless station's capability and request.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TL-WA750RE 150Mbps Universal WiFi Range Extender User Guide  
2) Shared Key - Select 802.11 Shared Key authentication type.  
3) Open System - Select 802.11 Open System authentication type.  
WEP Key Format - You can select ASCII or Hexadecimal format. ASCII format stands  
for any combination of keyboard characters in the specified length. Hexadecimal format  
stands for any combination of hexadecimal digits (0-9, a-f, A-F) in the specified length.  
WEP Key - Select which of the four keys will be used and enter the matching WEP key  
information for your network in the selected key radio button. These values must be  
identical on all wireless stations in your network.  
Key Type - You can select the WEP key length (64-bit, or 128-bit, or 152-bit.) for  
encryption. "Disabled" means this WEP key entry is invalid.  
1) For 64-bit encryption - You can enter 10 hexadecimal digits (any combination of 0-9,  
a-f, A-F, zero key is not permitted) or 5 ASCII characters.  
2) For 128-bit encryption - You can enter 26 hexadecimal digits (any combination of  
0-9, a-f, A-F, zero key is not permitted) or 13 ASCII characters.  
3) For 152-bit encryption - You can enter 32 hexadecimal digits (any combination of  
0-9, a-f, A-F, zero key is not permitted) or 16 ASCII characters.  
Note:  
If you do not set the key, the wireless security function is still disabled even if you have  
selected Shared Key as Authentication Type.  
Be sure to click the Save button to save your settings on this page.  
4.6.3 Wireless MAC Filtering  
Selecting Wireless > Wireless MAC Filtering will allow you to set up some filtering rules to  
control wireless stations accessing the device, which depend on the station’s MAC address on the  
following screen as shown Figure 4-19. Since the configurations are almost the same in either  
operation mode, here we just take that in Range Extender mode 1 for example.  
Figure 4-19 Wireless MAC address Filtering  
The Wireless MAC Address Filtering feature allows you to control wireless stations accessing the  
device, which depend on the station's MAC addresses.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
TL-WA750RE 150Mbps Universal WiFi Range Extender User Guide  
Operation Mode - Shows the current operation mode.  
Wireless MAC Filtering - Click the Enable button to trigger the Wireless MAC Address  
Filtering function. The default setting is disabled.  
To Add a Wireless MAC Address filtering entry, click the Add New… button. The “Add or Modify  
Wireless MAC Address Filtering entry" page will appear, shown in Figure 4-20.  
Figure 4-20 Add or Modify Wireless MAC Address Filtering entry  
MAC Address - Enter the wireless station's MAC address that you want to control.  
Description - Give a simple description of the wireless station.  
Status - Select a status for this entry, either Enabled or Disabled.  
To set up an entry, follow these instructions:  
First, you must decide whether the unspecified wireless stations can access the device or not. If  
you desire that the unspecified wireless stations can access the device, please select the radio  
button Deny the stations specified by any enabled entries in the list to access, otherwise,  
select the radio button Allow the stations specified by any enabled entries in the list to  
access.  
To add a MAC Address Filtering entry, follow these instructions:  
1. Enter the appropriate MAC Address into the MAC Address field. The format of the MAC  
Address is XX-XX-XX-XX-XX-XX (X is any hexadecimal digit). For example:  
00-0A-EB-B0-00-0B.  
2. Enter a simple description of the wireless station in the Description field. For example:  
Wireless station A.  
3. Select Enabled or Disabled for this entry on the Status pull-down list.  
4. Click the Save button to save this entry.  
To add additional entries, repeat steps 1-4.  
To modify or delete an existing entry:  
1. Click the Modify in the entry you want to modify. If you want to delete the entry, click the  
Delete.  
2. Modify the information.  
3. Click the Save button.  
Click the Enable All button to make all entries enabled  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
TL-WA750RE 150Mbps Universal WiFi Range Extender User Guide  
Click the Disable All button to make all entries disabled.  
Click the Delete All button to delete all entries  
Click the Next button to go to the next page and click the Previous button to return to the previous  
page.  
For example: If you desire that the wireless station A with MAC address 00-0A-EB-00- 07-BE is  
able to access the device, while all other wireless stations cannot access the device, you should  
configure the Wireless MAC Address Filtering list by following these steps:  
1. Click the Enable button to enable this function.  
2. Select the radio button: Allow the stations specified by any enabled entries in the list to  
access for Filtering Rules.  
3. Delete all or disable all entries if there are any entries already.  
4. Click the Add New... button and enter the MAC address 00-0A-EB-00-07-BE in the MAC  
Address field, enter Wireless Station A in the Description field and select Enabled in the  
Status pull-down list. Click the Save button.  
The filtering rules that configured should be similar to the following list:  
Note:  
If you enable the function and select the “Allow the stations specified by any enabled entries  
in the list to access” for Filtering Rules, and there are not any enabled entries in the list, thus,  
no wireless stations can access the device.  
4.6.4 Wireless Advanced  
Selecting Wireless > Wireless Advanced will allow you to do some advanced settings for the  
device in the following screen shown in Figure 4-21. Since the configurations are almost the same  
in either operation mode, here we just take that in Range Extender mode 1 for example.  
Figure 4-21 Wireless Advanced  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
TL-WA750RE 150Mbps Universal WiFi Range Extender User Guide  
Operation Mode - Shows the current Operation Mode.  
Transmit Power - Specifies the transmit power of the device. You can select High, Middle  
or Low which you would like. High is the default setting and is recommended.  
Beacon Interval - Specifies a value between 40-1000 milliseconds. The beacons are the  
packets sent by the device to synchronize a wireless network. Beacon Interval value  
determines the time interval of the beacons. The default value is 100.  
RTS Threshold - Specifies the RTS (Request to Send) Threshold. If the packet is larger  
than the specified RTS Threshold size, the device will send RTS frames to a particular  
receiving station and negotiate the sending of a data frame. The default value is 2346.  
Fragmentation Threshold - This value is the maximum size determining whether packets  
will be fragmented. Setting the Fragmentation Threshold too low may result in poor network  
performance since excessive packets. 2346 is the default setting and is recommended.  
DTIM Interval - Determines the interval of the Delivery Traffic Indication Message (DTIM).  
You can specify the value between 1-255 Beacon Intervals. The default value is 1, which  
indicates the DTIM Interval is the same as Beacon Interval.  
Enable WMM - WMM function can guarantee the packets with high- priority messages being  
transmitted preferentially. It is strongly recommended enabled.  
Enable Short GI - This function is recommended for it will increase the data capacity by  
reducing the guard interval time.  
Enable AP Isolation - Isolates all connected wireless stations so that wireless stations  
cannot access each other through WLAN.  
4.6.5 Wireless Statistics  
Selecting Wireless > Wireless Statistics will allow you to see the wireless transmission  
information in the following screen shown in Figure 4-22.  
Figure 4-22 Statistics of the device attached wireless stations  
Operation Mode - Shows the current operation mode.  
MAC Address - Shows the connected wireless station's MAC address.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
TL-WA750RE 150Mbps Universal WiFi Range Extender User Guide  
Current Status - The connected wireless station's running status, one of STA-AUTH /  
STA-ASSOC / STA-JOINED / WPA / WPA-PSK / WPA2 / WPA2-PSK / AP-UP / AP-DOWN /  
Disconnected.  
Received Packets - packets received by the station.  
Sent Packets - packets sent by the station.  
You cannot change any of the values on this page. To update this page and to show the current  
connected wireless stations, click the Refresh button.  
If the numbers of connected wireless stations go beyond one page, click the Next button to go to  
the next page and click the Previous button to return the previous page.  
Note:  
This page will be refreshed automatically every 5 seconds.  
4.6.6 Throughput Monitor  
Selecting Wireless > Throughput Monitor will helps to watch wireless throughput information in  
the following screen shown in Figure 4-23.  
Figure 4-23 Throughput Monitor  
Rate - The Throughput unit.  
Run Time - How long this function is running.  
Transmit - Wireless transmit rate information.  
Receive - Wireless receive rate information.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
TL-WA750RE 150Mbps Universal WiFi Range Extender User Guide  
Click the Start button to start wireless throughput monitor.  
Click the Stop button to stop wireless throughput monitor.  
4.7 DHCP  
DHCP stands for Dynamic Host Configuration Protocol. The DHCP Server will automatically  
assign dynamic IP addresses to the computers on the network. This protocol simplifies network  
management and allows new wireless devices to receive IP addresses automatically without the  
need to manually assign new IP addresses.  
There are two submenus under the DHCP menu (shown as Figure 4-24): DHCP Settings and  
DHCP Client List. Clicking either of them will enable you to configure the corresponding function.  
The detailed explanations for each submenu are provided below.  
Figure 4-24 The DHCP menu  
4.7.1 DHCP Settings  
Selecting DHCP > DHCP Settings will enable you to set up the Range Extender as a DHCP  
(Dynamic Host Configuration Protocol) server, which provides the TCP/IP configuration for all the  
PCs that are connected to the system on the LAN. The DHCP Server can be configured on the page  
(shown as Figure 4-26), only when you’ve set the Network LAN type as Static IP in Figure 4-15.  
Note:  
The DHCP Settings function cannot be configured if you have chosen Smart IP (DHCP) in  
Network -> LAN, in which situation the device will help you configure the DHCP automatically as  
you need. The DHCP Settings page will appear as Figure 4-25.  
Figure 4-25 DHCP Settings – Disabled  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
TL-WA750RE 150Mbps Universal WiFi Range Extender User Guide  
Figure 4-26 DHCP Settings – Enabled  
DHCP Server - Selecting the radio button before Disable/Enable will disable/enable the  
DHCP server on your Range Extender. The default setting is Enable. If you disable the  
Server, you must have another DHCP server within your network or else you must manually  
configure the computer.  
Start IP Address - This field specifies the first address in the IP Address pool. 192.168.0.100  
is the default start IP address.  
End IP Address - This field specifies the last address in the IP Address pool. 192.168.0.199  
is the default end IP address.  
Address Lease Time - Enter the amount of time for the PC to connect to the Range Extender  
with its current assigned dynamic IP address. The time is measured in minutes. After the time  
is up, the PC will be automatically assigned a new dynamic IP address. The range of the time  
is 1 ~ 2880 minutes. The default value is 120 minutes.  
Default Gateway (optional) - Enter the IP address of the gateway for your LAN. The factory  
default setting is 0.0.0.0.  
Default Domain (optional) - Enter the domain name of the your DHCP server. You can leave  
the field blank.  
Primary DNS (optional) - Enter the DNS IP address provided by your ISP. Consult your ISP  
if you don’t know the DNS value. The factory default setting is 0.0.0.0.  
Secondary DNS (optional) - Enter the IP address of another DNS server if your ISP provides  
two DNS servers. The factory default setting is 0.0.0.0.  
Click Save to save the changes.  
Note:  
To use the DHCP server function of the device, you should configure all computers in the LAN as  
"Obtain an IP Address automatically" mode. This function will not take effect until the device  
reboots.  
4.7.2 DHCP Client List  
Selecting DHCP > DHCP Client List will enable you to view the Client Name, MAC Address,  
Assigned IP and Lease Time for each DHCP Client attached to the device (Figure 4-27).  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
TL-WA750RE 150Mbps Universal WiFi Range Extender User Guide  
Figure 4-27 DHCP Clients List  
ID - Here displays the index of the DHCP client.  
Client Name - Here displays the name of the DHCP client.  
MAC Address - Here displays the MAC address of the DHCP client.  
Assigned IP - Here displays the IP address that the Range Extender has allocated to the  
DHCP client.  
Lease Time - Here displays the time of the DHCP client leased. Before the time is up, DHCP  
client will request to renew the lease automatically.  
You cannot change any of the values on this page. To update this page and to show the current  
attached devices, click on the Refresh button.  
4.8 System Tools  
System Tools option helps you to optimize the configuration of your device. You can upgrade the  
Range Extender to the latest version of firmware as well as backup or restore the Range  
Extender’s configuration files. It’s suggested that you change the default password to a more  
secure one because it controls access to the device’s web-based management page. Besides,  
you can find out what happened to the system in System Log.  
There are six submenus under the System Tools menu (shown as Figure 4-28): Firmware  
Upgrade, Factory Defaults, Backup & Restore, Reboot, Password, and System Log. Clicking  
any of them will enable you to configure the corresponding function. The detailed explanations for  
each submenu are provided below.  
Figure 4-28 The System Tools menu  
4.8.1 Firmware Upgrade  
Selecting System Tools > Firmware Upgrade allows you to upgrade the latest version of  
firmware for the device on the screen shown in Figure 4-29.  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
TL-WA750RE 150Mbps Universal WiFi Range Extender User Guide  
Figure 4-29 Firmware Upgrade  
New firmware versions are posted at http://www.tp-link.com and can be downloaded for free.  
Firmware Version - Here displays the current firmware version.  
Hardware Version - Here displays the current hardware version. The hardware version of the  
upgrade file must accord with the current hardware version.  
Note:  
1. There is no need to upgrade the firmware unless the new firmware has a new feature you  
want to use. However, when experiencing problems caused by the device itself, you can try to  
upgrade the firmware.  
2. Before upgrading the device’s firmware, you should write down some of your customized  
settings to avoid losing important configuration settings of device.  
To upgrade the device's firmware, follow these instructions:  
1. Download  
a
more recent firmware upgrade file from the TP-LINK website  
2. Enter the path name or click Browse… to select the downloaded file on the computer into the  
File blank.  
3. Click Upgrade.  
Note:  
Do not turn off the device or press the Reset button while the firmware is being upgraded. The  
device will reboot after the Upgrading has been finished.  
4.8.2 Factory Defaults  
Selecting System Tools > Factory Default allows you to restore the factory default settings for  
the device on the screen shown in Figure 4-30.  
Figure 4-30 Restore Factory Defaults  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
TL-WA750RE 150Mbps Universal WiFi Range Extender User Guide  
Click Restore to reset all configuration settings to their default values.  
1) Default User Name: admin  
2) Default Password: admin  
3) Default IP Address: 192.168.0.254  
4) Default Subnet Mask: 255.255.255.0  
Note:  
Any settings you have saved will be lost when the default settings are restored.  
4.8.3 Backup & Restore  
Selecting System Tools > Backup & Restore allows you to save all configuration settings to your  
local computer as a file or restore the device's configuration on the screen shown in Figure 4-31.  
Figure 4-31 Save or Restore the Configuration  
Click Backup to save all configuration settings to your local computer as a file.  
To restore the device's configuration, follow these instructions:  
1) Click Browse… to find the configuration file which you want to restore.  
2) Click Restore to update the configuration with the file whose path is the one you have input or  
selected in the blank.  
Note:  
The current configuration will be covered with the uploading configuration file. Wrong process will  
lead this device unmanaged. The restoring process lasts for 20 seconds and this device will restart  
automatically then. Keep the power of this device on during the process, in case of any damage.  
4.8.4 Reboot  
Selecting System Tools > Reboot allows you to reboot the device on the screen shown in Figure 4-32.  
Figure 4-32 Reboot the device  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
TL-WA750RE 150Mbps Universal WiFi Range Extender User Guide  
Click the Reboot button to reboot the device.  
Some settings of the device will take effect only after rebooting, which include:  
3) Change LAN IP Address (System will reboot automatically).  
4) Change the Wireless configurations.  
5) Change the Web Management Port.  
6) Upgrade the firmware of the device (system will reboot automatically).  
7) Restore the device's settings to factory defaults (system will reboot automatically).  
8) Update the configuration with a file (system will reboot automatically).  
4.8.5 Password  
Selecting System Tools > Password allows you to change the factory default user name and  
password of the device on the screen shown in Figure 4-33.  
Figure 4-33 Password  
It is strongly recommended that you change the factory default user name and password of the  
device. All users who try to access the device's web-based management page or Quick Setup will  
be prompted for the device's user name and password.  
Note:  
The new user name and password must not exceed 14 characters in length and must not include  
any spaces. Enter the new Password twice to confirm it.  
Click Save when finished.  
Click Clear All to clear all.  
4.8.6 System Log  
Selecting System Tools > System Log allows you to query the Logs of the device on the screen  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
TL-WA750RE 150Mbps Universal WiFi Range Extender User Guide  
Figure 4-34 System Log  
The device can keep logs of all traffic. You can query the logs to find what happened to the device.  
Log Type - By selecting the log type, only logs of this type will be shown.  
Log Level - By selecting the log level, only logs of this level will be shown.  
Click the Refresh button to show the latest log list.  
Click the Save Log button to save all the logs in a txt file.  
Click the Clear Log button to delete all the logs from the system permanently, not just from the  
page.  
Click the Next button to go to the next page, or click the Previous button return to the previous  
page.  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
TL-WA750RE 150Mbps Universal WiFi Range Extender User Guide  
Appendix A: Factory Defaults  
Item  
Default Value  
Common Default Settings  
Username  
admin  
Password  
admin  
IP Address  
192.168.0.254  
255.255.255.0  
Subnet Mask  
Domain  
Wireless  
SSID  
TP-LINK_Extender_XXXXXX  
Disabled  
Wireless Security  
Wireless MAC Address Filtering  
Disabled  
Note:  
The default SSID is TP-LINK_Extender_XXXXXX (XXXXXX indicates the last unique six  
characters of each device’s MAC address). This value is case-sensitive.  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
TL-WA750RE 150Mbps Universal WiFi Range Extender User Guide  
Appendix B: Troubleshooting  
T1. How do I restore my Range Extender’s configuration to its factory default settings?  
There are TWO methods available to restore the factory defaults.  
Method 1:  
With the Range Extender TL-WA750RE powered on, use a pin to press and hold the RESET  
button on the rear panel for more than 8 seconds before releasing it.  
Method 2:  
Get logged in to the web-based management page of TL-WA750RE, then go to “System  
Tools -> Factory Defaults” and click “Restore”.  
Note:  
Once the Range Extender is reset, the current configuration settings will be lost and you will  
need to reconfigure it.  
T2. What can I do if I forget my password?  
1) Restore the Range Extender’s configuration to its factory default settings. If you don’t  
know how to do that, please refer to previous T1;  
2) Use the default user name and password: admin, admin;  
3) Try to reconfigure your Range Extender by following the instructions of this UG.  
T3. What can I do if I cannot access the web-based configuration page?  
1) Check to verify all the connections (either wireless or wired ones) are proper. If yes,  
please proceed to the next step; otherwise, check the connections again.  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
TL-WA750RE 150Mbps Universal WiFi Range Extender User Guide  
2) Try to obtain an IP address and gateway; if succeed, open your web-browser, enter the  
default domain http://tplinkextender.net in the address field and get logged in.  
If you are unable to log in, please RESET the device, and then use the default IP address  
to get into the web-based configuration page, reconfigure the device.  
3) Feel free to contact our technical support, if the problem still persists.  
T4. How can I know that my wireless signal has been repeated and boosted by  
TL-WA750RE?  
An easy way is to compare the signal strength of your target wireless network (identified by its  
SSID), with TL-WA750RE in operation vs. out of operation. Before comparison, you’d better  
make sure your computer can obtain an IP address from your target wireless network and  
thus access the Internet, either via TL-WA750RE or without.  
T5. Will the Range Extender work if I connect the ETHERNET port of it to the router via  
Ethernet cable?  
Sorry, it won’t work. The Range Extender is designed to connect wirelessly to the router, while  
the ETHERNET port is designed to connect with a wired device, like Internet TV, Gaming  
console, DVR and so on.  
T6. Why does the wireless transmission rate speed down, while the wireless signal is  
stronger after repeated by TL-WA750RE?  
In compliance with the wireless transmission protocol, all the Range Extender devices are set  
to work in half-duplex instead of full-duplex mode. In other words, the Range Extender has to  
process one-way communication between your root Wireless router (or AP) and the terminal  
clients; so the transmission time will be double-increased, while the speed will be decreased.  
TP-LINK recommends that you connect to the Range Extender when your home network  
connection is poor, or when you want a larger wireless coverage to eliminate “dead zones”.  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TL-WA750RE 150Mbps Universal WiFi Range Extender User Guide  
Appendix C: Specifications  
General  
Standards and Protocols IEEE 802.3, 802.3u, 802.11n, 802.11b and 802.11g, TCP/IP, DHCP  
Safety & Emission  
Ports  
FCC, CE  
One 10/100M Auto-Negotiation LAN RJ45 port  
Wireless  
Frequency Band  
2.4~2.4835GHz  
11nup to 150MbpsAutomatic)  
11g54/48/36/24/18/12/9/6MAutomatic)  
11b11/5.5/2/1MAutomatic)  
Radio Data Rate  
Frequency Expansion  
Modulation  
DSSS (Direct Sequence Spread Spectrum)  
DBPSK, DQPSK, CCK, OFDM, 16-QAM, 64-QAM  
WEP, WPA-PSK, WPA2-PSK  
Security  
270M: -68dBm@10% PER  
108M: -68dBm@10% PER;  
54M: -68dBm@10% PER  
11M: -85dBm@8% PER;  
6M: -88dBm@10% PER  
1M: -90dBm@8% PER  
Sensitivity @PER  
Physical and Environment  
Working Temperature  
0~40(32~104)  
Working Humidity  
Storage Temperature  
Storage Humidity  
10% ~ 90% RH, Non-condensing  
-40~70(-40~158)  
5% ~ 95% RH, Non-condensing  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
TL-WA750RE 150Mbps Universal WiFi Range Extender User Guide  
Appendix D: Glossary  
802.11b - The 802.11b standard specifies a wireless networking at 11 Mbps using  
direct-sequence spread-spectrum (DSSS) technology and operating in the unlicensed radio  
spectrum at 2.4GHz, and WEP encryption for security. 802.11b networks are also referred to  
as Wi-Fi networks.  
802.11g - specification for wireless networking at 54 Mbps using direct-sequence  
spread-spectrum (DSSS) technology, using OFDM modulation and operating in the  
unlicensed radio spectrum at 2.4GHz, and backward compatibility with IEEE 802.11b devices,  
and WEP encryption for security.  
802.11n - 802.11n builds upon previous 802.11 standards by adding MIMO (multiple-input  
multiple-output). MIMO uses multiple transmitter and receiver antennas to allow for increased  
data throughput via spatial multiplexing and increased range by exploiting the spatial diversity,  
perhaps through coding schemes like Alamouti coding. The Enhanced Wireless Consortium  
(EWC) was formed to help accelerate the IEEE 802.11n development process and promote a  
technology specification for interoperability of next-generation wireless local area networking  
(WLAN) products.  
Access Point (Range Extender) - A wireless LAN transceiver or "base station" that can  
connect a wired LAN to one or many wireless devices. Access points can also bridge to each  
other.  
DNS (Domain Name System) An Internet Service that translates the names of websites into  
IP addresses.  
Domain Name - A descriptive name for an address or group of addresses on the Internet.  
DoS (Denial of Service) - A hacker attack designed to prevent your computer or network from  
operating or communicating.  
DSL (Digital Subscriber Line) - A technology that allows data to be sent or received over  
existing traditional phone lines.  
ISP (Internet Service Provider) - A company that provides access to the Internet.  
MTU (Maximum Transmission Unit) - The size in bytes of the largest packet that can be  
transmitted.  
SSID - A Service Set Identification is a thirty-two character (maximum) alphanumeric key  
identifying a wireless local area network. For the wireless devices in a network to  
communicate with each other, all devices must be configured with the same SSID. This is  
typically the configuration parameter for a wireless PC card. It corresponds to the ESSID in  
the wireless Access Point and to the wireless network name.  
WEP (Wired Equivalent Privacy) - A data privacy mechanism based on a 64-bit or 128-bit or  
152-bit shared key algorithm, as described in the IEEE 802.11 standard.  
Wi-Fi –A trademark of the Wi-Fi Alliance and the brand name for products using the IEEE  
802.11 family of standards.  
WLAN (Wireless Local Area Network) - A group of computers and associated devices  
communicate with each other wirelessly, which network serving users are limited in a local  
area.  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
TL-WA750RE 150Mbps Universal WiFi Range Extender User Guide  
WPA (Wi-Fi Protected Access) - WPA is a security technology for wireless networks that  
improves on the authentication and encryption features of WEP (Wired Equivalent Privacy). In  
fact, WPA was developed by the networking industry in response to the shortcomings of WEP.  
One of the key technologies behind WPA is the Temporal Key Integrity Protocol (TKIP). TKIP  
addresses the encryption weaknesses of WEP. Another key component of WPA is built-in  
authentication that WEP does not offer. With this feature, WPA provides roughly comparable  
security to VPN tunneling with WEP, with the benefit of easier administration and use. This is  
similar to 802.1x support and requires a RADIUS server in order to implement. The Wi-Fi  
Alliance will call this, WPA-Enterprise. One variation of WPA is called WPA Pre Shared Key  
or WPA-Personal for short - this provides an authentication alternative to an expensive  
RADIUS server. WPA-Personal is a simplified but still powerful form of WPA most suitable for  
home Wi-Fi networking. To use WPA-Personal, a person sets a static key or "passphrase" as  
with WEP. But, using TKIP, WPA-Personal automatically changes the keys at a preset time  
interval, making it much more difficult for hackers to find and exploit them. The Wi-Fi Alliance  
will call this, WPA-Personal.  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Technics Stereo Receiver SA DA8 User Manual
Topcom Network Card WBR 754SG User Manual
Toro Lawn Mower 3000 User Manual
Toshiba Cell Phone G810 User Manual
Toshiba Computer Hardware TMP87CM24AF User Manual
Triarch Indoor Furnishings 33223 User Manual
Verizon Network Card PC5750 User Manual
ViewSonic Computer Monitor A71F+ User Manual
VocoPro Speaker SUB 1500 User Manual
VTech Cordless Telephone VT5875 User Manual