TL-R4299G
Dual-WAN SMB Broadband Router
Rev:1.0.1
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
•
Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.
Download from Www.Somanuals.com. All Manuals Search And Download.
Package contents
The following contents should be found in your box:
¾
¾
¾
One TL-R4299G Dual-WAN SMB Broadband Router
One power cord for TL-R4299G Dual-WAN SMB Broadband Router
One Resource CD for TL-R4299G Dual-WAN SMB Broadband Router, including:
•
•
This Guide
Other Helpful Information
¾
Mounting kits for installing in a standard 19-inch rack
Note:
)
If any of the listed contents are damaged or missing, please contact the retailer from whom you
purchased the product for assistance.
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Chapter 1. Introduction ........................................................................................ 1
1.1 Overview of the Router.................................................................................................. 1
1.2 Features......................................................................................................................... 1
1.3 Conventions................................................................................................................... 2
Chapter 2. Hardware installation......................................................................... 2
2.1 Panel Layout.................................................................................................................. 2
2.1.1 The Front Panel................................................................................................................2
2.1.2 The Rear Panel ................................................................................................................3
2.2 System Requirements ................................................................................................... 3
2.3 Installation Environment Requirements......................................................................... 3
2.4 Connecting the Router................................................................................................... 4
Chapter 3. Quick Installation Guide .................................................................... 5
3.1 Configure PC ................................................................................................................. 5
3.2 Login.............................................................................................................................. 8
Chapter 4. Configuring the Router .................................................................... 11
4.1 Status........................................................................................................................... 11
4.2 Quick Setup ................................................................................................................. 13
4.3 Network........................................................................................................................ 13
4.3.1 LAN.................................................................................................................................13
4.3.2 WAN ...............................................................................................................................14
4.3.3 Network service detection..............................................................................................25
4.3.4 MAC Clone.....................................................................................................................26
4.3.5 Flow Balance..................................................................................................................26
4.3.6 Balance Policy................................................................................................................28
4.3.7 WAN Port Parameter......................................................................................................30
4.4 DHCP........................................................................................................................... 31
4.4.1 DHCP Settings ...............................................................................................................31
4.4.2 DHCP Clients List...........................................................................................................32
4.4.3 Address Reservation......................................................................................................33
4.5 Forwarding................................................................................................................... 34
4.5.1 Virtual Servers................................................................................................................34
4.5.2 Port Triggering................................................................................................................36
4.5.3 DMZ................................................................................................................................38
4.5.4 UPnP ..............................................................................................................................39
4.6 Security........................................................................................................................ 40
4.6.1 Firewall...........................................................................................................................40
4.6.2 IP Filtering ......................................................................................................................41
4.6.3 Domain Filtering .............................................................................................................44
4.6.4 MAC Filtering..................................................................................................................45
Download from Www.Somanuals.com. All Manuals Search And Download.
4.6.5 Screen............................................................................................................................47
4.7 Static Routing .............................................................................................................. 50
4.8 Session Limit ............................................................................................................... 52
4.8.1 Session Limit..................................................................................................................52
4.8.2 Session List....................................................................................................................53
4.9 QoS.............................................................................................................................. 53
4.9.1 QoS Settings ..................................................................................................................54
4.9.2 QoS Rules List ...............................................................................................................54
4.10 IP & MAC Binding........................................................................................................ 55
4.10.1 Binding Setting ...............................................................................................................55
4.10.2 ARP List..........................................................................................................................57
4.11 Dynamic DNS .............................................................................................................. 58
4.11.1 Dyndns DDNS................................................................................................................58
4.11.2 PeanutHull DDNS...........................................................................................................59
4.11.3 Comexe DDNS...............................................................................................................59
4.12 Switch Setting.............................................................................................................. 60
4.12.1 Port Statistics .................................................................................................................61
4.12.2 Port Mirror ......................................................................................................................61
4.12.3 Port Rate Control............................................................................................................62
4.12.4 Port Parameter...............................................................................................................63
4.12.5 Port Status......................................................................................................................64
4.12.6 Port VLAN ......................................................................................................................65
4.13 System Tools............................................................................................................... 65
4.13.1 Time Settings .................................................................................................................66
4.13.2 Firmware.........................................................................................................................67
4.13.3 Factory Defaults .............................................................................................................67
4.13.4 Backup and Restore.......................................................................................................68
4.13.5 Reboot............................................................................................................................69
4.13.6 Password........................................................................................................................70
4.13.7 System Log ....................................................................................................................71
4.13.8 Remote Management.....................................................................................................71
4.13.9 Statistics.........................................................................................................................72
4.13.10WAN Speed Detect ........................................................................................................73
4.13.11IP NAT Table..................................................................................................................75
4.13.12NAT Source Port Settings ..............................................................................................75
Appendix A: Specifications................................................................................... 76
Appendix B: FAQ.................................................................................................... 77
Appendix C: Glossary............................................................................................ 81
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Chapter 1.Introduction
1.1 Overview of the Router
Dual-WAN SMB Broadband Router User Guide
The TL-R4299G Dual-WAN SMB Broadband Router possesses excellent throughput and driving
load capability, which consumedly meets the requirements from Internet cafe and small
/medium/sizable enterprise with volumes of users, making a more expedite communication. The
superior performance will bring you full-new experience of a non-bottle-neck network.
TL-R4299G Dual-WAN SMB Broadband Router makes plenty of applications become a reality. It
can be used for constructing intranet FTP, WEB, and Mail server, etc. Inaccessibly, it features
network game ports opened, MSN audio conversation and special application setting, providing
much more additional value to your network.
TL-R4299G Dual-WAN SMB Broadband Router provides two WAN ports, with plugging two wan
lines, the export bandwidth of it could be multi-time-increased, enjoying various service from
different ISPs. The router features fully automatically load balance policy, no need for any
manually work, it works with backup and load balancing functions. The connection will furbish
when one line is broken down, while the streaming will part automatically.
Featuring firewall and VPN Passthrough, the TL-R4299G Dual-WAN SMB Broadband Router
resists most common Internet attacks and ensures secure data connectivity and transmission
over the Internet.
TL-R4299G Dual-WAN SMB Broadband Router is easy-to-manage. Quick Setup is supported
and friendly help messages are provided for every step. So you can configure it quickly and share
Internet access, files and fun comfortably.
1.2 Features
¾
¾
¾
¾
¾
¾
¾
¾
¾
¾
Intel IXP core, main frequency up to 533Hz
Complies with IEEE 802.3, 802.3u , 802.3x, 802.1x standards
8 LAN ports, 2 WAN ports, backup connections automatically for each other
Support Port Bandwidth Control, Port Mirror, Port-based VLAN for LAN ports
Supports QoS based on IP address
Built-in NAT and DHCP server supporting static IP address distributing
Supports Virtual Server, Port Triggering, and DMZ host
Built-in firewall supporting IP address filtering, Domain Name filtering, and MAC address filtering
Supports connecting/disconnecting Internet at a specified time of day
Supports access control, allowing parents and network administrators to establish restricted
access policies based on the time of day for children or staff
Supports TCP/IP, PPPoE, DHCP, ICMP, NAT, SNTP
¾
¾
¾
Supports UPnP, Dynamic DNS, Static Routing, VPN pass-through
Supports Traffic Statistics
1
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
¾
¾
¾
¾
Supports ICMP-FLOOD, UDP-FLOOD, TCP-SYN-FLOOD filter
Ignores Ping packets from WAN or LAN ports
Supports firmware upgrade
Supports Remote and Web management
1.3 Conventions
Parameters provided in the pictures are just references for setting up the product, which may
differ from the actual situation.
You can set the parameters according to your demand.
Chapter 2.Hardware installation
2.1 Panel Layout
2.1.1 The Front Panel
The front panel of the TL-R4299G consists of several LED indicators, which is designed to
indicate connections. Viewed from left, the next table describes the LEDs on the front panel of the
router.
Figure 2-1
LED Descriptions:
Name
Action
Not lit
Lit up
Not lit
Lit up
Not lit
Lit up
Description
The router is power off
Power
The router is power on
The router works properly
The router has a hardware error
The router has a hardware error
The router has a hardware error
M1
M2
M1 and M2 are flashing
synchronously, the router is
restoring the factory default
settings.
Flashing The router works properly
Not lit
Lit up
There is no device linked to the corresponding port
WAN/LAN
(Link/Act)
There is a device linked to the corresponding port but no activity
Flashing There is an active device linked to the corresponding port
Not lit
Lit up
Not lit
Lit up
The linked device is running at 10Mbps
100M(WAN)
1000M(LAN)
The linked device is running at 100Mbps
The linked device is running at 10Mbps or 100Mbps
The linked device is running at 1000Mbps
2
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
The front panel contains the following features. (Viewed from left to right)
Reset: Use the button to restore the router to the factory defaults.
Dual-WAN SMB Broadband Router User Guide
¾
There are two ways to reset the router:
Method one: Use the Factory Defaults function on System Tools -> Factory Defaults page in
the router's Web-based Utility.
Method two: Use the Factory Default Reset button. First, turn off the router's power. Second,
press the default reset button, then turn on the router's power, and hold the reset button until the
M1 and M2 LED flash simultaneously (about 3 seconds). At last, release the reset button and wait
for the router to reboot.
Note:
)
Ensure the router is powered on before it restarts completely.
¾
¾
WAN: Two RJ45 port for connecting the router to a cable, DSL modem or Ethernet
LAN: Eight 10/100/1000Mbps RJ45 port for connecting the router to the local PCs
2.1.2 The Rear Panel
The rear panel of the TL-R4299G only features a power receptacle, which is an AC power
receptacle. Connect the female of the power cord head here, and the male head to the AC power
outlet.
Figure 2-2
2.2 System Requirements
¾
¾
Broadband Internet Access Service (DSL/Cable/Ethernet)
One DSL/Cable modem that has an RJ45 connector (It’s not necessary if you connect the
router to Ethernet)
¾
Each PC on the LAN needs a working Ethernet Adapter and an Ethernet cable with RJ45
connectors
¾
¾
TCP/IP protocol must be installed on each PC
Web browser, such as Microsoft Internet Explorer 5.0 or later, Netscape Navigator 6.0 or later
2.3 Installation Environment Requirements
¾
¾
Not in direct sunlight or near a heater or heating vent
Not cluttered or crowded. There should be at least 2 inches (5 cm) of clear space on all sides
of the router
¾
¾
Well ventilated (especially if it is in a closet)
Operating temperature: 0℃~40℃ (32℉~104℉)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
¾
Operating Humidity: 10%~90%RH, Non-condensing
Note:
)
Do not use this product near water, for example, in a wet basement or near a swimming pool.
Avoid using this product during an electrical storm. There may be a remote risk of electric shock
from lightning.
2.4 Connecting the Router
Before you install the router, you should connect your PC to the Internet through your broadband
service successfully. If there is any problem, please contact with your ISP for help. After that,
please install the router according to the following steps. Don't forget to pull out the power plug
and keep your hands dry.
1. Power off your PC(s), Cable/DSL modem, and the router.
2. Connect the PC(s) and all Switches/Hubs on your LAN to the LAN Ports on the router, shown
in figure 2-3.
3. Connect the DSL/Cable modem to the WAN port on the router, shown in figure 2-3.
4. Connect the AC power adapter to the AC power socket on the router, and the other end into
an electrical outlet. The router will start to work automatically.
5. Power on your PC(s) and Cable/DSL modem.
Figure 2-3
4
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Chapter 3.Quick Installation Guide
After connecting the TL-R4299G router into your network, you should configure it. This chapter
describes how to configure the basic functions of your TL-R4299G Dual-WAN SMB Broadband
Router. These procedures only take you a few minutes. You can access the Internet via the router
immediately after it has been successfully configured.
3.1 Configure PC
Step 1: Click the Start menu on your desktop, right click My Network Places, and then select
Figure 3-1
Step 2: In the next screen, right click Local Area Connection (LAN), and then select
Properties.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Figure 3-2
Step 3: In the next screen, select General tab, highlight Internet Protocol (TCP/IP), and then
click the Properties button.
Figure 3-3
6
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Figure 3-4
Note:
)
You can configure the PC to get an IP address manually, select “Obtain an IP address
automatically” and “Obtain DNS server address automatically” in the screen above.
Now, you can run the Ping command in the command prompt to verify the network connection.
Please click the Start menu on your desktop, select run tab, type cmd in the field, and then type
ping 192.168.1.1 on the next screen, and then press Enter.
If the result displayed is similar to the screen below, the connection between your PC and the
Router has been established.
Figure 3-5
7
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
If the result displayed is similar to the screen shown below, it means that your PC has not
connected to the Router.
Figure 3-6
You can check it follow the steps below:
Note:
)
Is the connection between your PC and the Router correct?
The LEDs of LAN port which you link to the device and the LEDs on your PC's adapter should be lit.
Is the TCP/IP configuration for your PC correct?
If the Router's IP address is 192.168.1.1, your PC's IP address must be within the range of
192.168.1.2 ~ 192.168.1.254, the gateway must be 192.168.1.1.
3.2 Login
Once your host PC is properly configured, please proceed as follows to use the Web-based Utility:
Start your web browser and type the private IP address of the Router in the URL field:
192.168.1.1.
After that, you will see the screen shown below, enter the default User Name admin and the
default Password admin, and then click OK to access to the Quick Setup screen. You can follow
the steps below to complete the Quick Setup.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Figure 3-7
Note:
)
proxy. Choose Tools menu→Internet Options→Connections→LAN Settings, in the screen
that appears, cancel the Using Proxy checkbox, and click OK to finish it.
Step 1: Select the Quick Setup tab on the left of the main menu and the “Quick Setup” screen
will appear. Click the Next button.
Figure 3-8
Step 2: Select the connection type to connect to the ISP and then click the Next button.
Figure 3-9
9
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Note:
)
The router supports three popular ways to connect to Internet. Please select one compatible with
your ISP, if you are given another way not listed here, refer to Network→ WAN for detailed list.
Username and Password provided by your ISP. These fields are case sensitive. If you
have difficulty with this process, please contact your ISP.
Figure 3-10
parameters from your ISP without needing to enter any parameters.
Click the Next button
Figure 3-11
Step 6: After that, you will see the next screen. Click Finish to complete the quick installation.
Figure 3-12
10
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Chapter 4.Configuring the Router
This User Guide recommends using the “Quick Installation Guide” for first-time installation. For
advanced users, if you want to know more about this device and make use of its functions
adequately, you need to read this chapter and configure advanced settings though the
Web-based Utility.
After your successful login, you can configure and manage the router. There are main menus on
the left of the Web-based Utility. Submenus will be available after you click one of the main menus.
On the center of the web-based Utility, you can configure the function. Besides this, you can refer
to the help on the right of the Web-based Utility. To apply any settings you have altered on the
page, please click the Save button.
4.1 Status
Choose “Status” menu, you can view the router's current status and configuration as shown in
11
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Figure 4-1
¾
¾
LAN - This field displays the current information for the LAN, including the “MAC address”,
“IP address” and “Subnet Mask”.
WAN 1~2 - This field displays the parameters applied to the WAN ports of the router,
including “MAC address”, “IP address”, “Subnet Mask”, “Default Gateway” and so on.
Note:
)
If PPPoE/L2TP/PPTP is chosen as the WAN connection type, the Disconnect button will be
shown here while you are accessing the Internet. You can also cut the connection by clicking the
button. If you have not connected to the Internet, a Connect button will be shown, you can then
establish the connection by clicking the button.
¾
¾
Traffic Statistics: This field displays the traffic statistics of WAN ports.
System Up Time: This field displays the time of the router running from the time it is powered
on or is reset.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
4.2 Quick Setup
4.3 Network
Choose menu “Network”, the next submenus are shown below:
Figure 4-2
Click any of them, and you will be able to configure the corresponding function. The detailed
explanations for each submenu are provided below.
4.3.1 LAN
Choose menu “Network→LAN”, you can configure the IP parameters of the LAN on the screen
below.
Figure 4-3
¾
¾
¾
MAC Address - This field displays the physical address of the LAN. The value can't be
changed.
IP Address - Enter the IP address for the LAN of the Router, the formal is in dotted-decimal
notation (the factory default value is 192.168.1.1).
Subnet Mask - Enter the subnet mask for the LAN of the Router, this address code
determines the size of the network. Normally use 255.255.255.0 as the subnet mask.
Note:
)
1) If you change the IP address of the LAN, you must use the new IP address to login to the
router.
2) If the new LAN IP Address you set is not in the same subnet, the IP Address pool in the
13
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
DHCP sever will not take effect, until they are re-configured. Besides this, the Virtual Server
and DMZ Host may change accordingly at the same time, you’d better re-configure it as well.
4.3.2 WAN
Choose menu “Network→WAN”, you can configure the IP parameters of the WAN on the screen
below.
The Router provides six connection types for WAN to connect to the Internet, they are “Dynamic
IP”, “Static IP” , “PPPoE”, ”BigPondCable” , “L2TP” and “PPTP” For configuring the WAN, you
should select the connection type firstly according your needs.
1. Dynamic IP
If you aren’t given any login parameters and IP information, please select Dynamic IP (shown in
button to renew the IP parameters from your ISP. Click the Release button to release the IP
parameters.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Figure 4-4
¾
¾
¾
interior network: When the WAN is connecting with a LAN, you can select the option, and
enter the LAN IP addresses in the field, then the WAN port will only transmit the traffic whose
destination IP address are contained in the field.
MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks
is 1500 Bytes. For some ISPs you need to reduce the MTU. But this is rarely required, and
should not be done unless you are sure it is necessary for your ISP connection.
Primary DNS & Secondary DNS - If your ISP gives you one or two DNS addresses, select
Use These DNS Servers and enter the primary and secondary addresses into the correct
fields. Otherwise, the DNS servers will be assigned dynamically from ISP.
Note:
)
If you get ‘Address not found' errors when you go to a Web site, it is likely that your DNS servers
are set up improperly. You should contact your ISP to get correct DNS server.
¾
Get IP with Unicast DHCP: A few ISPs' DHCP servers do not support the broadcast
15
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
applications. If you can not get the IP address normally, you can choose this option. (You
don’t need select this option generally).
¾
¾
Ingress Bandwidth: Enter the bandwidth for ingress traffic.
Egress Bandwidth: Enter the bandwidth for egress traffic.
2. Static IP
If you are given a fixed IP (static IP), please select Static IP (shown in Figure 4-5), and then fixed
IP parameters specified by your ISP.
Figure 4-5
¾
¾
IP Address - Enter the IP address in dotted-decimal notation provided by your ISP.
Subnet Mask - Enter the subnet Mask in dotted-decimal notation provided by your ISP,
usually is 255.255.255.0.
¾
¾
Default Gateway - Enter the gateway IP address in dotted-decimal notation provided by your
ISP (Optional).
MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet
networks is 1500 Bytes. For some ISPs you may need to modify the MTU. But this is rarely
required, and should not be done unless you are sure it is necessary for your ISP
connection.
¾
Primary DNS - Type the DNS address in dotted-decimal notation provided by your ISP
16
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
(Optional).
¾
Secondary DNS - Type another DNS address in dotted-decimal notation provided by your
ISP if provided (Optional).
¾
¾
Ingress Bandwidth: Enter the bandwidth for ingress traffic.
Egress Bandwidth: Enter the bandwidth for egress traffic.
3. PPPoE
are not sure which connection type you use currently, please contact your ISP to obtain the
correct information.
Figure 4-6
¾
¾
User Name/Password - Enter the User Name and Password provided by your ISP. These
fields are case-sensitive.
Connect on Demand - You can configure the router to disconnect your Internet connection
after a specified period of inactivity (Max Idle Time). If your Internet connection has been
terminated due to inactivity, Connect on Demand enables the router to automatically
re-establish your connection as soon as you attempt to access the Internet again. If you wish
to activate Connect on Demand, click the radio button.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Note:
)
1) If you want your Internet connection to remain active at all times, enter 0 in the Max Idle Time
field. Otherwise, enter the number of minutes you want to have elapsed before your Internet
connection terminates.
2) Sometimes the connection can not be disconnected although you specify a time to Max Idle
Time. This is because there may still be active applications in the background, which may
cause fee accounted by your ISP.
¾
Connect Automatically - Connect automatically after the router is disconnected. To use this
option, click the radio button.
¾
Time-based Connecting - You can configure the router to make it connect or disconnect
based on time. Enter the start time in HH:MM for connecting and end time in HH:MM for
disconnecting in the Period of Time fields.
Note:
)
Only you have set the system time on System Tools→Time screen, will the Time-based
Connecting function take effect.
¾
Connect Manually - You can configure the router to make it connect or disconnect manually.
After a specified period of inactivity (Max Idle Time), the router will disconnect your Internet
connection, and not be able to re-establish your connection automatically even though you
attempt to access the Internet again. You need click the Connect button manually to connect
immediately, or click the Disconnect button manually to disconnect immediately; To use this
option, click the radio button. If you want your Internet connection to remain active at all times,
enter 0 in the Max Idle Time field. Otherwise, enter the number in minutes that you wish to
have the Internet connecting last unless a new link is requested.
Note:
)
1) If you want your Internet connection to remain active at all times, enter 0 in the Max Idle Time
field. Otherwise, enter the number in minutes that you wish to have the Internet connecting
last unless a new link is requested.
2) Sometimes the connection cannot be disconnected although you specify a time to Max Idle
Time. This is because there may still be active applications in the background, which may
cause fee accounted by your ISP.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Figure 4-7
¾
MTU Size- The default MTU size is 1492 bytes, which is usually fine. For some ISPs, you
need modify the MTU. This should not be done unless you are sure it is necessary for your
ISP.
¾
¾
Service Name/AC Name - The service name and AC (Access Concentrator) name should
not be configured unless you are sure it is necessary for your ISP.
ISP Specified IP Address - If you know that your ISP does not automatically transmit your IP
address to the router during login, select Use IP Address specified by ISP and enter the IP
address in dotted-decimal notation, which your ISP provided.
¾
¾
Detect Online Interval - The default value is 0, you can input the value between 0 and 120.
The router will detect Access Concentrator online at every interval between the time. If the
value is 0, it means the Router does not detect.
Primary DNS & Secondary DNS - If you know that your ISP does not automatically transmit
DNS addresses to the router during login, select Use the following DNS servers and enter
the address in dotted-decimal notation of your ISP’s primary DNS server. If a secondary DNS
server address is available, enter it as well.
¾
¾
Ingress Bandwidth: Enter the bandwidth for download traffic.
Egress Bandwidth: Enter the bandwidth for upload traffic.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
4. BigPondCable
If your ISP provides BigPond Cable (or Heart Beat Signal) connection, please select BigPond
Cable option.
Figure 4-8
¾
User Name/Password - Enter the User Name and Password provided by your ISP. These
fields are case-sensitive.
¾
¾
¾
Auth Server - Enter the authenticating server IP address or host name.
Auth Domain - Type in the domain suffix server name based on your location.
MTU Size - The normal MTU (Maximum Transmit Unit) value for most Ethernet networks is
1500 bytes. For some ISPs, you may need to modify the MTU. But this is rarely required, and
should not be done unless you are sure it is necessary for your ISP connection.
Connect on Demand - You can configure the router to disconnect your Internet connection
¾
20
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
after a specified period of the Internet connectivity (Max Idle Time). If your Internet
connection has been terminated due to inactivity, Connect on Demand enables the router to
automatically re-establish your connection as soon as you attempt to access the Internet
again. If you wish to activate Connect on Demand, click the radio button. If you want your
Internet connection to remain active at all times, enter 0 in the Max Idle Time field. Otherwise,
enter the number of minutes you want to have elapsed before your Internet connection
terminates.
¾
¾
Connect Automatically - Connect automatically after the router is disconnected. To use this
option, click the radio button.
Connect Manually - You can configure the router to make it connect or disconnect manually.
After a specified period of inactivity (Max Idle Time), the router will disconnect your Internet
connection, and not be able to re-establish your connection automatically as soon as you
attempt to access the Internet again. To use this option, click the radio button. If you want
your Internet connection to remain active at all times, enter 0 in the Max Idle Time field.
Otherwise, enter the number in minutes that you wish to have the Internet connecting last
unless a new link requested.
Note:
)
Sometimes the connection cannot be disconnected although you specify a time to Max Idle Time
because some applications visit the Internet continually in the background.
5. L2TP
If your ISP provides L2TP connection, please select L2TP option.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Figure 4-9
¾
¾
User Name/Password - Enter the User Name and Password provided by your ISP. These
fields are case-sensitive.
Connect on Demand - You can configure the router to disconnect your Internet connection
after a specified period of the Internet connectivity (Max Idle Time). If your Internet
connection has been terminated due to inactivity, Connect on Demand enables the router to
automatically re-establish your connection as soon as you attempt to access the Internet
again. If you wish to activate Connect on Demand, click the radio button. If you want your
Internet connection to remain active at all times, enter 0 in the Max Idle Time field. Otherwise,
22
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
enter the number of minutes you want to have elapsed before your Internet connection
terminates.
¾
¾
Connect Automatically - Connect automatically after the router is disconnected. To use this
option, click the radio button.
Connect Manually - You can configure the router to make it connect or disconnect manually.
After a specified period of inactivity (Max Idle Time), the router will disconnect your Internet
connection, and not be able to re-establish your connection automatically as soon as you
attempt to access the Internet again. To use this option, click the radio button. If you want
your Internet connection to remain active at all times, enter 0 in the Max Idle Time field.
Otherwise, enter the number in minutes that you wish to have the Internet connecting last
unless a new link requested.
Note:
)
Sometimes the connection cannot be disconnected although you specify a time to Max Idle Time
because some applications visit the Internet continually in the background.
6. PPTP
If your ISP provides PPTP connection, please select PPTP option.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Figure 4-10
¾
¾
User Name/Password - Enter the User Name and Password provided by your ISP. These
fields are case-sensitive.
Connect on Demand - You can configure the router to disconnect your Internet connection
after a specified period of the Internet connectivity (Max Idle Time). If your Internet
connection has been terminated due to inactivity, Connect on Demand enables the router to
automatically re-establish your connection as soon as you attempt to access the Internet
again. If you wish to activate Connect on Demand, click the radio button. If you want your
Internet connection to remain active at all times, enter 0 in the Max Idle Time field. Otherwise,
24
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
enter the number of minutes you want to have elapsed before your Internet connection
terminates.
¾
¾
Connect Automatically - Connect automatically after the router is disconnected. To use this
option, click the radio button.
Connect Manually - You can configure the router to make it connect or disconnect manually.
After a specified period of inactivity (Max Idle Time), the router will disconnect your Internet
connection, and not be able to re-establish your connection automatically as soon as you
attempt to access the Internet again. To use this option, click the radio button. If you want
your Internet connection to remain active at all times, enter 0 in the Max Idle Time field.
Otherwise, enter the number in minutes that you wish to have the Internet connecting last
unless a new link requested.
Note:
)
Sometimes the connection cannot be disconnected although you specify a time to Max Idle Time
because some applications visit the Internet continually in the background.
4.3.3 Network service detection
Choose menu “Network→Network service detection”, you can Use WAN Network Service
Detection feature on next screen, this router can detect the Internet connection online or not.
Figure 4-11
¾
By Ping - Detect whether Internet connection is online or not by Ping.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
¾
¾
¾
Destination IP Address for Ping - Enter the correct IP address that really existed on the
WAN network. For example: 202.96.134.188.
By DNS Query - Detect whether Internet connection is online or not by sending query packet
to DNS Server.
DNS Server IP Address - Enter the correct DNS IP address that really existed on the WAN
network. For example: 202.96.134.133.
4.3.4 MAC Clone
Choose menu “Network→MAC Clone”, you can configure the MAC address of the WAN on the
screen below (shown in Figure 4-12).
Some ISPs require that you register the MAC address of your adapter, which is connected to your
cable, DSL modem or Ethernet during installation. You do not generally need to change anything
here.
Figure 4-12
¾
WAN MAC Address (1~2) - This field displays the current MAC address of the WAN port,
which is used for the WAN port. If your ISP requires that you register the MAC address,
please enter the correct MAC address into this field. The format for the MAC address is
XX-XX-XX-XX-XX-XX (for example: 00-0A-EB- E6-B9-49).
¾
Your PC's MAC Address - This field displays the MAC address of the PC that is managing
the router. If the MAC address is required, you can click the Clone MAC Address button
and this MAC address will fill in the “WAN MAC Address” field.
Note:
)
1) Click Restore Factory MAC to restore the MAC address of WAN port to the factory
default value.
2) Only the PC(s) on your LAN can use the MAC Address Clone feature.
3) After you finish the configuration, click the Save button, and the router will prompt you to
reboot.
4.3.5 Flow Balance
Choose menu “Network→Flow Balance”, you can specify priority channels according to source
or destination IP addresses, distributing flexibly Internet resource and services from different
26
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
ISPs. For example, you can specify some packets prior forwarding from WAN port 1, which
depend on specified source or destination IP addresses.
Figure 4-13
¾
¾
Enable/Disable WAN - Enable the WAN port you want to use, then click Save to make it
effective.
Additional IP Address dispatch rules - Enable the function and then make the dispatch
rules.
¾
¾
Backup - Click the button to backup the list files.
Upload - Click the button to upload an existed file. You can click Browse to locate the
specific file first, and then click the Upload List Files to complete the process.
Rules list - This table displays the current dispatch rules.
¾
To add a dispatch rule:
Step 2: Select the Rules select, protocol, Datagram Pass Policy and Transmit Path, enter IP
address and Port like the next screen shows.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Figure 4-14
Click Save.
To add additional rules, repeat steps 1-3.
Click the Delete button to delete the entry.
Click the Enable All button to enable all the entries.
Click the Disable All button to disable all the entries.
Click the Delete All button to delete all the entries.
Click the Previous button to view the information in the previous screen, click the Next button to
view the information in the next screen.
4.3.6 Balance Policy
Choose menu “Network→Flow Balance”, you can configure the balance policy in the next
screen.
This screen configure the WAN's foward policies.These policies are based on three principles:
Speed First, Paired IP First, Application First. We use two tables to register correlative datas, they
are Speed Detect Table, Fast Connection Table, Paired IP Table, Application Table. Note that,
the time parameters below are configured with the corresponding tables, and they have passed
relevant tests, if you are not sure, please don't change the settings.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Figure 4-15
¾
On Fastest-Session - If you select the option, the data will be transmited through one of the
WAN ports which connect the WAN much quicker than the other.
•
•
•
Faster age for Speed-Detect-Table
-
Faster timeouts for the entries in
Speed-Detect-Table.
Age for Speed-Detect-Table - Normal timeouts for the entries in speed-Detect-Table.
During the time, if an entry has never been used, the entry will be deleted from the table.
Threshold for Faster-Session - During the time, if the Router receives a response from
Internet, then the connection will be considered as a fast session. And the connection will
be registered in the Faster-Session-Table.
•
•
Age for Faster-Session-Table - Normal timeouts for the entries in Faster-Session-Table.
During the time, if an entry has never been used, the entry will be deleted from the table.
Obliged age for Fastest-Session-Table - Obliged timeouts for the entries in
Fastest-Session-Table.
¾
On Existed-IP-Pair - If a pair of IP addresses has made a connection via a particular WAN
port, then the paired IP address will be registered in the Paired IP Table, and the later
connections between the paired IP will be made through the WAN port also.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
•
•
Age for IP-Pairs-Table - Normal timeouts for the entries in Paired-IP-first Table. During
the time, if an entry has never been used, the entry will be deleted from the Paired IP
Table.
Obliged age for IP-Pairs-Table - The maximal timeouts for the entries in IP-Pairs-Table.
During the time, the entry will be deleted from the Paired IP Table no matter whether the
entry has been used.
¾
On Existed-Application - If a application has initiated two connections via a particular WAN
port , then the connection will be registered in the Application Table, and the later
connections related to the application will be made through the WAN port also.
•
Age for Application-Table - Normal timeouts for the entries in Application-Table. During
the time, if an entry has never been used, the entry will be deleted from the Application
Table.
•
Obliged age for Application-Table - The maximal timeouts for the entries in
Application-Table. During the time, the entry will be deleted from the Application Table no
matter whether the entry has been used.
Note:
)
The time settings have passed corresponding tests, if you are not sure, please leve it default.
4.3.7 WAN Port Parameter
Choose menu “Network→WAN Port Parameter”, you can view the information about the WAN
ports in the next screen.
Figure 4-16
¾
¾
WAN Index - This shows the Router's WAN ports.
Port Status - This shows the ports' current status: Enabled or Disabled, the default status is
30
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Enabled.
¾
¾
¾
¾
Flow Control - This displays whether the Flow Control is Enabled, "Enabled" means the
function is enabled, "Disabled" means the function is't enabled.
Negotiation Mode - The options are: Auto Negotiation, 10M Half Duplex, 10M Full
Duplex,100M Half Duplex,100M Full Duplex.
Ingress Limit Mode & Ingress Limit Speed - Select the limit mode and limit speed for the
WAN ports.
Egress Limit & Egress Limit speed - Enable Egress Limit for WAN ports and select the limit
speed for them.
Note:
)
Egress speed limit is designed for controlling the broadcasting storm. When the current flux
oversteps the setting value, the overstepped datagrams will be discarded.
4.4 DHCP
Choose menu “DHCP”, you can see the submenus under the main menu: DHCP Settings, DHCP
Clients List and Address Reservation.
Figure 4-17
Click any of them, and you will be able to configure the corresponding function. The detailed
explanations for each submenu are provided below.
4.4.1 DHCP Settings
Choose menu “DHCP→DHCP Settings”, you can configure the DHCP in the next screen (shown
The router is set up by default as a DHCP (Dynamic Host Configuration Protocol) server, which
provides the TCP/IP configuration for all the PCs that are connected to the router on the LAN.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Figure 4-18
¾
DHCP Server - Enable or disable the DHCP server. If you disable the Server, you must
have another DHCP server within your network or else you must manually configure the
computer.
¾
¾
¾
Start IP Address - This field specifies the first address in the IP address pool. The default
address is 192.168.1.100.
End IP Address - This field specifies the end address in the IP address pool. The default
address is 192.168.1.199.
Address Lease Time - This is the amount of time in which a network user will be allowed
connection to the router with their current dynamic IP address. Enter the amount of time (in
minutes), the range of the time is 1 ~ 2880 minutes. The default value is 120 minutes.
Default Gateway - Suggest to input the IP address of the LAN port of the router, default
value is 192.168.1.1. (Optional)
¾
¾
¾
Default Domain - Input the domain name of your network. (Optional)
Primary DNS - Input the DNS IP address provided by your ISP. You can consult your ISP
for it. (Optional)
¾
Secondary DNS - Input the IP address of another DNS server if your ISP provides two DNS
servers. (Optional)
Note:
)
To use the DHCP server function of the router, you must configure all computers on the LAN as
"Obtain an IP Address automatically" mode. This function will take effect until the router reboots.
4.4.2 DHCP Clients List
Choose menu “DHCP→DHCP Clients List”, you can view the information about the clients
32
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
update the information.
Figure 4-19
¾
¾
¾
Client Name - This field displays the name of the DHCP client
MAC Address - This field displays the MAC address of the DHCP client
Assigned IP - This field displays the IP address that the router has allocated to the DHCP
client.
¾
Lease Time - This field displays the time of the DHCP client leased. Before the time is up,
DHCP client will request to renew the lease automatically.
4.4.3 Address Reservation
Choose menu “DHCP→Address Reservation”, you can view and add reserved addresses for
clients via the next screen (shown in Figure 4-20).
If you specify a reserved IP address for a PC on the LAN, that PC will always receive the same IP
address each time when it accesses the DHCP server. Reserved IP addresses should be
assigned to servers that require permanent IP settings.
Figure 4-20
¾
MAC Address - This field displays the MAC address of the PC for which you want to
reserve IP address.
¾
¾
Assigned IP Address - This field displays the IP address of the router reserved.
Status - This field displays the status of the virtual server entry. Enabled means that the
entry will take effect, Disabled means that the entry will not take effect.
To add/modify a reserved IP address:
33
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Step 2: Enter the MAC address, IP address and select Status as shown in the screen below.
Figure 4-21
Step 3: Click the Save button when finished.
Note:
)
4) If you want to add more than one reserved IP, please go to step 1 to continue.
5) The function won't take effect until the router reboots.
Click the Delete button to delete the entry.
Click the Enable All button to enable all the entries.
Click the Disable All button to disable all the entries.
Click the Delete All button to delete all the entries.
Click the Previous button to view the information in the previous screen, click the Next button to
view the information in the next screen.
4.5 Forwarding
Choose menu “Forwarding”, you can see the submenus under the main menu: Virtual Servers,
Port Triggering, DMZ and UPnP.
Figure 4-22
Click any of them, and you will be able to configure the corresponding function. The detailed
explanations for each submenu are provided below.
4.5.1 Virtual Servers
Choose menu “Forwarding→Virtual Servers”, you can view and add virtual servers in the next
34
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Virtual servers can be used for setting up public services on your LAN, such as DNS, Email and
FTP. A virtual server is defined as a service port, and all requests from Internet to this service port
will be redirected to the computer specified by the server IP. Any PC that was configured as a
virtual server must have a static or a reserved IP address because its IP address may change
when using the DHCP function.
Figure 4-23
¾
Service Port - This field displays the numbers of External Ports. It can be a service port or a
range of service ports (the format is XXX - YYY, XXX is Start port, YYY is End port).
IP Address - This field displays the IP address of the PC running the service application.
Protocol - This field displays the protocol used for this application, either TCP, UDP, or All
(all protocols supported by the router).
¾
¾
¾
Status - This field displays the status of the virtual server entry. Enabled means that the
entry will take effect, Disabled means that the entry will not take effect.
To add/modify a virtual server entry:
Step 2: Select the service you want from the “Common Service Port”, then the port and
protocol value will be added to the corresponding field automatically, you only need to
configure the IP address for the virtual server; If the “Common Service Port” does not
contain the service that you want, please configure the Service Port, IP Address and
Protocol manually.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Figure 4-24
Step 3: After that, select Enable to make the entry take effect.
Step 4: Click Save button to save the configuration.
Note:
)
6) If you want to add more than one reserved IP, please go to step 1 to continue.
7) It is possible that you configure more than one type of available service on a computer or
server, it means the IP addresses for the virtual servers are same.
Other configurations for the entries as shown in Figure 4-24:
Click the Delete button to delete the entry.
Click the Enable All button to enable all the entries.
Click the Disable All button to disable all the entries.
Click the Delete All button to delete all the entries.
Click the Previous button to view the information in the previous screen, click the Next button to
view the information in the next screen.
Note:
)
If you set the virtual server of the service port as 80, you must set the web management port on
System Tools –> Remote Management screen to be any value except 80 such as 8080. Or else
there will be a conflict to disable the virtual server.
4.5.2 Port Triggering
Choose menu “Forwarding→Port Triggering”, you can view and add port triggerings in the next
Some applications require multiple connections, like Internet games, video conferencing, Internet
calling and so on. These applications cannot work with a pure NAT router. Port Triggering is used
for some of these applications that can work with an NAT router.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Figure 4-25
¾
¾
¾
Trigger Port - This displays the port for outgoing traffic. An outgoing connection using this
port will "Trigger" this rule.
Trigger Protocol - This displays the protocol used for Trigger Ports, either TCP,UDP, or All
(all protocols supported by the router).
Incoming Ports - This displays the port or port range used by the remote system, they are
used for responding to the outgoing request. A response using one of these ports will be
forwarded to the PC that triggered this rule. You can input at most 5 groups of ports (or port
section). Every group of ports must be apart with ",". For example, 2000-2038, 2050-2051,
2085, 3010-3030.
¾
¾
Incoming Protocol - This displays the protocol used for Incoming Ports Range, either TCP
or UDP, or ALL (all protocols supported by the router).
Status - This displays the status. Enabled means that the rule will take effect, Disabled
means that the rule will not take effect.
Once configured, the operation for Port Triggering will proceed as follows:
Step 1: A local host makes an outgoing connection using a destination port number defined in
the Trigger Port field.
Step 2: The router records this connection, opens the incoming port or ports associated with this
entry in the Port Triggering table, and associates them with the local host.
Step 3: When necessary, the external host will be able to connect to the local host using one of
the ports defined in the Incoming Ports field.
To add/modify a port triggering entry:
Step 2: Select the application you want from the “Common Applications”, then the Trigger port
and Incoming ports will be added to the corresponding field automatically, you only need
to configure the Trigger protocol and Incoming Protocol for the entry; If the “Common
Applications” does not contain the applications that you want, please configure these
options manually.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Figure 4-26
Step 3: After that, select Enabled to make the entry take effect.
Step 4: Click Save button to save the configuration.
Note:
)
1) If you want to add more than one reserved IP, please go to step 1 to continue.
2) When the trigger connection is released, the according opening ports will be closed.
3) Each rule allowed to be used only by one host on LAN synchronously. The trigger
connection of other hosts on LAN will be refused.
4) Incoming Port Range cannot overlap each other.
Other configurations for the entries as shown in Figure 4-26:
Click the Delete button to delete the entry.
Click the Enable All button to enable all the entries.
Click the Disable All button to disable all the entries.
Click the Delete All button to delete all the entries.
Click the Previous button to view the information in the previous screen, click the Next button to
view the information in the next screen.
4.5.3 DMZ
Choose menu “Forwarding→DMZ”, you can view and configure DMZ host in the screen (shown
The DMZ host feature allows one local host to be exposed to the Internet for a special-purpose
service such as Internet gaming or videoconferencing. DMZ host forwards all the ports at the
same time. Any PC whose port is being forwarded must have its DHCP client function disabled
and should have a new static IP address assigned to it because its IP address may change when
using the DHCP function.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Figure 4-27
To assign a computer or server to be a DMZ server:
Step 1: Click the Enable radio button
Step 2: Enter the local host IP address in the DMZ Host IP Address field
Step 3: Click the Save button.
Note:
)
After you set the DMZ host, the firewall related to the host will not take effect.
4.5.4 UPnP
Choose menu “Forwarding→UPnP”, you can view the information about UPnP in the screen
viewing the information.
The Universal Plug and Play (UPnP) feature allows the devices, such as Internet computers, to
access the local host resources or devices as needed. UPnP devices can be automatically
discovered by the UPnP service application on the LAN.
Figure 4-28
¾
Current UPnP Status - If you want to use the Router’s UPnP function, please click Enable
button. If you don’t want use the function, please click Disable button. Allowing the function
may cause a risk to security, this feature is disabled by default.
App Description - This displays the description provided by the application in the UPnP
request.
¾
¾
External Port - This displays the external port, which the router opened for the application.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
¾
¾
¾
¾
Protocol - This displays the protocol for the application.
Internal Port - This displays the Internal port, which the router opened for local host.
IP Address - The UPnP device that is currently accessing the router.
Status - This displays the status. Enabled means that the port is still active, Disabled
means that the port is inactive.
4.6 Security
Choose menu “Security”, you can see the submenus under the main menu: Firewall, IP
Address Filtering, Domain Filtering, MAC Filtering, and Screen.
Figure 4-29
Click any of them, and you will be able to configure the corresponding function. The detailed
explanations for each submenu are provided below.
4.6.1 Firewall
Choose menu “Security→Firewall”, you can control the general firewall switch in the next screen
Filtering, MAC Address Filtering and Screen are disabled, their settings are ineffective in the
default settings.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Figure 4-30
¾
¾
Enable Firewall - Enable the general firewall switch or not.
Enable IP Address Filtering - Enable the IP Address Filtering or not. There are two default
filtering rules, please select the rule for your need.
¾
¾
Enable Domain Filtering - Enable the Domain Filtering or not.
Enable MAC Address Filtering - Enable MAC Address Filtering or not. There are two
default filtering rules, please select the rule for your need.
¾
Enable Screen - Enable the screen function or not.
4.6.2 IP Filtering
Choose menu “Security→IP Address Filtering”, you can configure the IP Address filtering rule
Internet Access by specific users on your LAN based on their IP addresses.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Figure 4-31
¾
¾
Effective Time - This is the time or the range of time for the entry to take effect. For example,
1800 - 2200, it means that the entry will take effect from 18:00 to 22:00.
LAN IP - This is the LAN IP address or the range of LAN IP addresses in dotted-decimal
notation format. For example, 192.168.1.20 - 192.168.1.30. Keep the field blank, which
means all LAN IP addresses are controlled by the rule.
¾
¾
LAN Port - This is the LAN Port or the range of LAN ports in the field. For example, 1030 -
2000. Keep the field blank, which means all LAN ports are controlled by the rule.
WAN IP - This is the WAN IP address or the range of WAN IP addresses in dotted-decimal
notation format. For example, 202.96.134.210 – 202.96.134.230. Keep the field blank, which
means all WAN IP addresses are controlled by the rule.
¾
¾
¾
WAN Port - This is the WAN Port or the range of WAN Ports. For example, 25 – 110. Keep
the field blank, which means all WAN Ports are controlled by the rule.
Protocol - This indicates which protocol is used, either TCP, UDP, or All (all protocols
supported by the router).
Action - This field displays the action that the Router takes to deal with the traffic. Allow
means that the Router allows the traffic through the Router, Deny means that the Router
rejects the traffic through the router.
¾
Status - This field displays the status of the rule. Enabled means the rule will take effect,
Disabled means the rule will not take effect.
To add/modify an IP Address filtering entry:
For example: If you desire to block E-mail received and sent by the IP address 192.168.1.7 on
your local network during the time of 1800 to 2200; And wish to make the PCs with IP addresses
192.168.1.8 to 192.168.1.12 unable to visit the website of IP address 202.96.134.12 all the day,
while other PCs have no limit. You can configure the rules as follows.
packets not specified by any filtering rules to pass through the router".
42
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Step 4: Enter the “LAN IP Address”, “LAN Port”, “WAN IP Address” and “WAN Port” in the
corresponding field as shown in Figure 4-32.
Step 5: Select the “Protocol”, “Action” and “Status” for the rule as shown in the next screen.
Figure 4-32
Step 6: Click the Save button to save this entry.
Step 7: Go to Step 2 to complete the other rules continually.
After you finish the configurations, you will see the rules in the table below:
Figure 4-33
Note:
)
Before adding an IP Address Filtering entry, you should enable the Firewall and the IP Address
Other configurations for the entries as shown in Figure 4-31:
Click the Delete button to delete the entry.
Click the Enable All button to enable all the entries.
Click the Disable All button to disable all the entries.
Click the Delete All button to delete all the entries.
Click the Previous button to view the information in the previous screen, click the Next button to
view the information in the next screen.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
4.6.3 Domain Filtering
Choose menu “Security→Domain Filtering”, you can configure the Domain filtering rule in the
certain websites on the Internet by specifying their domains or key words.
Figure 4-34
¾
¾
¾
Effective Time - This is the time or the range of time for the entry to take effect. For example,
0800 - 2400, it means that the entry will take effect from 08:00 to 20:00.
Domain Name - This is the domain or key word as desired. Leaving the field blank means all
websites on the Internet are prohibited from accessing.
Status - This field displays the status, Enabled means the rule is effective, Disabled means
the rule is ineffective.
To add or modify a Domain Filtering entry:
For example: if you want to block the PCs on your LAN from accessing websites
for other websites, you can configure as follows.
4-30).
Step 3: Enter the “Effective time” that the rule will take effect, enter the “Domain Name” as
Step 4: Select the “Status” for the rule as shown in the next screen.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Figure 4-35
Step 5: Finally, click Save to make the rule take effect.
Step 6: Go to Step 2 to complete the other rules continually.
After you finish the configurations, you will see the rules in the table below:
Figure 4-36
Note:
)
Before adding an IP Address Filtering entry, you should enable the Firewall and the IP Address
Other configurations for the entries as shown in Figure 4-31:
Click the Delete button to delete the entry.
Click the Enable All button to enable all the entries.
Click the Disable All button to disable all the entries.
Click the Delete All button to delete all the entries.
Click the Previous button to view the information in the previous screen, click the Next button to
view the information in the next screen.
4.6.4 MAC Filtering
Choose menu “Security→MAC Filtering”, you can configure the MAC Address filtering rule in
access to the Internet by users on your local network based on their MAC addresses.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Figure 4-37
¾
MAC Address - .This is the PC’S MAC address which is controlled by the rule, its format of is
XX-XX-XX-XX-XX-XX (X is any hexadecimal digit). For example: 00-0E-AE-B0-00-0B.
Description - This is the description about the PC, Fox example: John’s PC.
Status - This field displays the status, Enabled means the rule is effective, Disabled means
the rule is ineffective.
¾
¾
To add or modify a Domain Filtering entry:
Fox example: If you want to block the PCs with MAC addresses 00-0A-EB-00-07-BE and
00-0A-EB-00-07-5F to access the Internet, you can configure as follows.
Step 1: Enable the “Firewall” and “MAC Address Filtering” on the Firewall screen (show in
Figure 4-30). And then specify the Default MAC Address Filtering Rule "Deny these PCs
with enabled rules to access the Internet".
Step 3: Enter the appropriate MAC address and descriptions, then select the status as shown in
46
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Figure 4-38
Step 4: Finally, click Save to make the rule take effect.
Step 5: Go to Step 2 to complete the other rules continually.
After you finish the configurations, you will see the rules in the table below:
Figure 4-39
Note:
)
Before adding a MAC Address Filtering entry, you should enable the Firewall and the MAC
Other configurations for the entries as shown in Figure 4-31:
Click the Delete button to delete the entry.
Click the Enable All button to enable all the entries.
Click the Disable All button to disable all the entries.
Click the Delete All button to delete all the entries.
Click the Previous button to view the information in the previous screen, click the Next button to
view the information in the next screen.
4.6.5 Screen
Choose menu “Security→Screen”, you can configure the functions below to protect the router
from being attacked in the next two screens.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Figure 4-40
¾
¾
Region - This option used to select the specifically area from which the packets will be
monitored by the next settings.
Scan Attack Defence
•
IP Scan: During the specific time, if a computer (identified by a particular source IP
address) transmits packets to at least ten different computers (identified by different
destination IP addresses), then the source IP address will be deemed to make IP Attacks.
And the Router will start up the blocking function immediately.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
•
•
Port Scan - During the specific time, if a computer (identified by a particular source IP
address) transmits TCP SYN packets to another computer's (identified by a destination
IP address) ten different ports, then the source IP address will be deemed to make Port
Attacks. And the Router will start up the blocking function immediately.
IP Snoop - If you select this option, the Router will monitor whether the packets from the
particular region is doing IP deceive. In the event, the Router will start up the blocking
function immediately. Note: The function takes effect only when the Region is LAN.
¾
DoS Attack Defence
•
•
•
•
•
ICMP Flood - - During a second, if a destination IP addresses receives many packets,
and the number of these packets exceeds the prescript value, then the destination IP will
be deemed to suffering from ICMP Flood Attack. And the Router will start up the blocking
function immediately.
UDP Flood - During a second, if a particular port of a destination IP addresses receives
many packets, and the number of these packets exceeds the prescript value, then the
Port will be deemed to suffering from UDP Flood Attack. And the Router will start up the
blocking function immediately.
SYN Flood - During a second, if a particular port of a destination IP addresses receives
many TCP SYN packets, and the number of these packets exceeds the prescript value,
then the Port will be deemed to suffering from SYN Flood Attack. And the Router will
start up the blocking function immediately.
Land Attack - This is an attack combining Flood attack and IP spoofing. When the
attackers send the spoof SYN datagram which including the casualty's IP address and
make it the destination and source IP addreess, the LAND attack happens. And the
Router will start up the blocking function immediately.
WinNuke - WinNuke is a Dos attack for any Windows computers runing in the internet.
The attackers send the TCP fragment (usually sets the emergent field to the Net BIOS'S
139 port) to the connection established computers. So the NetBIOS fragments created
and make the Windows computers collapse. And the Router will start up the blocking
function immediately.
¾
Dubious Packet Defence
•
Large ICMP packet: The normal ICMP packets are very short, there normal length is
shorter than 1024 Bytes. If the ICMP packets' length is larger than 1024 Bytes, then they
will be considered as large ICMP packets. And the Router will start up the blocking
function immediately.
•
•
•
TCP packet without Flag: The normal TCP packets contain flag in the packet header,
or else the packets will be considered as abnormal dubious packets. And the Router will
start up the blocking function immediately.
TCP packet with both SYN and FIN: The TCP packets which have both SYN and FIN
settings in the packets header will be considered as abnormal TCP packets. And the
Router will start up the blocking function immediately.
TCP packet with FIN but without ACK: The TCP packets that contains FIN but without
49
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
ACK is considered as abnormal. And the Router will start up the blocking function
immediately.
•
Unknow Protocol - In IP head the protocol type field, 135 and the value bigger than 135
is reserved and undefined. Because the protocols are undefined, we can not predict a
specifically unknow protocol is well-meaning or baleful. To these nonstandard protocols,
the carefully attitude is the best way to prevent them interning into the protected network.
¾
Packet Defence with IP option
•
•
•
•
•
•
•
IP Timestamp Option: If you select this option, the Router will monitor whether the IP
packets from the particular region contain the field of Internet Timestamp. In the event,
the Router will start up the blocking function immediately.
IP Security Option: If you select this option, the Router will monitor whether the IP
packets from the particular region contain the field of Security. In the event, the Router
will start up the blocking function immediately.
IP Stream Option: If you select this option, the Router will monitor whether the IP
packets from the particular region contain the field of of Stream ID. In the event, the
Router will start up the blocking function immediately.
IP Record Route Option: If you select this option, the Router will monitor whether the IP
packets from the particular region contain the field of Record Route. In the event, the
Router will start up the blocking function immediately.
IP Loose Source Route Option: If you select this option, the Router will monitor
whether the IP packets from the particular region contain the field of Loose Source Route.
In the event, the Router will start up the blocking function immediately.
IP Strict Source Route Option: If you select this option, the Router will monitor whether
the IP packets from the particular region contain the field of Strict Source Route. In the
event, the Router will start up the blocking function immediately.
Invalid IP option: If you select this option, the Router will monitor whether the IP
packets from the particular region is integrated or right. In the event, the Router will start
up the blocking function immediately.
4.7 Static Routing
Choose menu “Static Routing”, you can configure the static route in the next screen (shown in
Figure 4-41). A static route is a pre-determined path that network information must travel to reach
a specific host or network.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Figure 4-41
¾
¾
¾
¾
Destination IP Address - The “Destination IP Address” is the address of the network or host
that you want to assign to a static route.
Subnet Mask - The “Subnet Mask” determines which portion of an IP address is the network
portion, and which portion is the host portion.
Default Gateway - This is the IP address of the gateway device that allows for contact
between the router and the network or host.
Status - This field displays the status, Enabled means the rule is effective, Disabled means
the rule is ineffective.
To add/modify a static routing entry:
Step 2: Enter the appropriate Destination IP Address, Subnet Mask and Default Gateway, and
then select the status.
Figure 4-42
Step 3: Click Save to make the entry take effect.
Note:
)
If you want to add more than one static route, please go to step 1 to continue.
Other configurations for the entries as shown in Figure 4-31:
51
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Click the Delete button to delete the entry.
Click the Enable All button to enable all the entries.
Click the Disable All button to disable all the entries.
Click the Delete All button to delete all the entries.
Click the Previous button to view the information in the previous screen, click the Next button to
view the information in the next screen.
4.8 Session Limit
Choose menu “Session Limit”, you can see the submenus under the main menu:
Figure 4-43
Click any of them, and you will be able to configure the corresponding function. The detailed
explanations for each submenu are provided below.
4.8.1 Session Limit
Choose menu “Session Limit→Session Limit”, you can view and configure the session limits in
the next screen. For conveniently control the connections of the computers in the LAN, you can
set the max number of connections for different computers.
Figure 4-44
¾
¾
Enable: Enable or disable the session limit. Only after choose "Enable", the configuration will
take effect.
LAN IP address: The controlled computer's IP address. You can input an range of IP
address, for example: 192.168.1.20 -192.168.1.30. You can also input an IP address, such
as:192.168.1.40.
¾
Max Session: The max connections of the computer.
To add/modify a session limit entry:
52
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Step 2: Enter the appropriate LAN IP Address, Max Session and then select the status.
Figure 4-45
Step 3: Click the Save button.
4.8.2 Session List
Choose menu “Session Limit→Session List”, you can view the the information about the
number of connection.
Figure 4-46
Note:
)
You can click the Refresh to update the information.
4.9 QoS
Choose menu “QoS”, you can see the submenus under the main menu:
Figure 4-47
Click any of them, and you will be able to configure the corresponding function. The detailed
explanations for each submenu are provided below.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
4.9.1 QoS Settings
Choose menu “QoS→QoS Settings”, you can configure the Upload Bandwidth and Download
Bandwidth in the next screen, their value you configure should be less than 1000000Kbps.
Figure 4-48
4.9.2 QoS Rules List
Choose menu “QoS→QoS Rules List”, you can view and configure the QoS rules in the screen
below.
Figure 4-49
¾
Description - This is the information about the rules such as address range.
Mode - Mode can be separated into “independent bandwidth” and “share bandwidth”.
Independent bandwidth means every port has its own upload and download bandwidth,
share bandwidth means address or port share upload and download bandwidth.
Egress bandwidth - This field displays the max and mix upload bandwidth through the WAN
port, the default is 0.
¾
¾
¾
Ingress bandwidth - This field displays the max and mix download bandwidth through the
WAN port, the default is 0.
¾
¾
Enable - This displays the status of the rule.
Modify - Click “Modify” to edit the rule, click “Delete” to delete the rule.
To add/modify a QoS rule:
Step 2: Enter the information like the screen shown below.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Figure 4-50
Step 3: Click the Save button.
4.10 IP & MAC Binding
Choose menu “IP & MAC Binding”, you can see the submenus under the main menu: Binding
Setting, ARP List.
Figure 4-51
Click any of them, and you will be able to configure the corresponding function. The detailed
explanations for each submenu are provided below.
4.10.1 Binding Setting
Choose menu “IP & MAC Binding→Binding Setting”, you can view and add IP & MAC binding
entries in the next screen (shown in Figure 4-52).
55
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Figure 4-52
¾
¾
MAC Address - This field displays the MAC address of the controlled computer in the LAN.
IP Address - This field displays the assigned IP address of the controlled computer in the
LAN.
¾
Bind - Select Whether enable the arp binding or not. Only bind the MAC address and IP
address can the function take effect.
To add/modify an IP & MAC binding entry:
Step 2: Enter the MAC Address and IP Address in the corresponding field.
Figure 4-53
Step 3: Select Bind the MAC and IP address, then click Save button to save the configuration.
To find a specific IP & MAC binding entry:
Step 2: Enter the specific MAC Address or IP Address in the corresponding field.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Figure 4-54
Step 3: Click Find button, then you will see the entry with the specific MAC address or IP
address.
Step 4: Click Back to return the previous screen.
Note:
)
You can click “to page” to edit the entry in the corresponding screen.
Other configurations for the entries as shown in Figure 4-52:
Click the Delete button to delete the entry.
Click the Enable All button to enable all the entries.
Click the Delete All button to delete all the entries.
Click the Previous button to view the information in the previous screen, click the Next button to
view the information in the next screen.
4.10.2 ARP List
Choose menu “IP & MAC Binding→ARP List”, you can view the ARP list in the next screen
Binding entries.
To manage the computer, you could observe the computers in the LAN by checking the
relationship of MAC address and IP address on the ARP list, and you could configure the items on
the ARP list also.
Figure 4-55
57
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Click Delete to load the specific item to the IP & MAC Binding list.
Click the Bind All button to bind all the current items, available after enable.
Click the Refresh button to refresh all items.
Note:
)
An item could not be loaded to the IP & MAC Binding list if the IP address of the item has been
loaded before.
4.11 Dynamic DNS
Choose menu “Dynamic DNS”, you can configure Dynamic DNS function.
The router offers a Dynamic Domain Name System (DDNS) feature. DDNS lets you assign a fixed
host and domain name to a dynamic Internet IP address. It is useful when you are hosting your
own website, FTP server, or other server behind the router. Before using this feature, you need to
The Dynamic DNS client service provider will give you a password or key.
4.11.1 Dyndns DDNS
(shown in Figure 4-56).
Figure 4-56
¾
Connection Status - The status of the DDNS service is displayed here.
To set up for Dyndns DDNS, follow these instructions:
58
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Step 1: Select the WAN port to configure.
Step 2: Type the “User Name” and “Password” for your DDNS account.
Step 3: Enter the domain name that your dynamic DNS service provider offers.
Step 4: Enable DDNS, and click Save to save the current configuration.
Click Login to login the DDNS service.
Click Logout to logout the DDNS service.
4.11.2 PeanutHull DDNS
(shown in Figure 4-57).
Figure 4-57
To set up for PeanutHull DDNS, follow these instructions:
Step 1: Select the WAN port to configure.
Step 2: Type the User Name and Password for your DDNS account.
Step 3: Enable DDNS, and click Save to save the current configuration.
Click the Login button to login to the DDNS service.
Click Logout to logout of the DDNS service.
4.11.3 Comexe DDNS
(shown in Figure 4-58).
59
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Figure 4-58
To set up for Comexe DDNS, follow these instructions:
Step 1: Select the WAN port to configure.
Step 2: Enter the domain name your dynamic DNS service provider offer.
Step 3: Type the “User Name” and “Password” for your DDNS account.
Step 4: Enable DDNS, and click Save to save the current configuration.
Click Login to login the DDNS service.
Click Logout to logout the DDNS service.
4.12 Switch Setting
Choose menu “Switch Setting”, you can see the submenus under the main menu:
60
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Figure 4-59
Click any of them, and you will be able to configure the corresponding function. The detailed
explanations for each submenu are provided below.
4.12.1 Port Statistics
Choose menu “Switch Setting→Port statistics”, you can view the statistics information about
the LAN port in the next screen (shown in Figure 4-60).
Figure 4-60
Note:
)
Before you view the information, please click the
button to update it.
Refresh
4.12.2 Port Mirror
Choose menu” Switch Setting→Port Mirror”, you can configure the Mirror modes,Mirror Port
and the Mirrored Ports below.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Figure 4-61
¾
Mirror Config - There are three Mirror modes: Disable, Output mirror, Input mirror. The
Output/Input mirror is related to the Router.
¾
¾
Port Mirror - This is the port linked to the mirror computer.
Mirrored Ports List - The option used to select ports to be mirrored.
Note:
)
You should make sure that the Mirror Port and the Mirrored Ports are in the same VLAN.
4.12.3 Port Rate Control
Choose menu “Switch Setting→Port Rate Control”, you can control the ingress and egress rate
for the LAN port in the next screen (shown in Figure 4-62).
62
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Figure 4-62
4.12.4 Port Parameter
Choose menu “Switch Setting→Port Parameter”, you can configure the parameters for the LAN
port in the next screen (shown in Figure 4-63).
63
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
4.12.6 Port VLAN
Choose menu “Switch Setting→Port VLAN”, you can view and configure the VLAN table.
Figure 4-65
¾
¾
¾
¾
Port - You can select them as the members of VLAN.
Enable - This used to enable the corresponding VLAN configuration.
Clean - Click this button, you can make all the entries Disabled.
Save - Click this button, the Router will make a new VLAN table according to the current
configuration, and the enabled VLAN will take effect.
4.13 System Tools
Choose menu “System Tools”, you can see the submenus under the main menu:
Figure 4-66
65
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Click any of them, and you will be able to configure the corresponding function. The detailed
explanations for each submenu are provided below.
4.13.1 Time Settings
Choose menu “System Tools→Time Settings”, you can configure the time on the screen
(shown in Figure 4-67).
Figure 4-67
¾
¾
¾
Time zone - Select your local time zone from this pull down list.
Date - Enter your local date in MM/DD/YY into the right blanks.
Time - Enter your local time in HH/MM/SS into the right blanks.
To configure the system time manually:
Step 1: Select your local time zone.
Step 2: Enter date and time in the right blanks.
Step 3: Click Save to save the configuration.
To configure the system automatically:
Step 1: Enter the address of the preferred NTP server.
Step 2: Click the Get GMT button to get system time from Internet if you have connected to the
Internet.
Step 3: Click Save to save the configuration.
Note:
)
1) This setting will be used for some time-based functions such as firewall. You must
specify your time zone once you login to the router successfully, or else, the time limited
on these functions will not take effect.
2) The time will be lost if the router is turned off.
3) The router will obtain GMT time automatically from Internet if it has already connected to
the Internet.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
4.13.2 Firmware
Choose menu “System Tools→Firmware”, you can update the latest version of firmware for the
Router on the screen (shown in Figure 4-68).
Figure 4-68
¾
¾
Firmware Version - This displays the current firmware version.
Hardware Version - This displays the current hardware version. The hardware version of the
upgrade file must accord with the Router’s current hardware version.
To upgrade the router's firmware, follow these instructions below:
Step 1: Download a more recent firmware upgrade file from the TP-LINK website
Step 2: Type the path and file name of the update file into the “File” field. Or click the Browse
button to locate the update file.
Step 3: Click the Upgrade button.
Note:
)
the router is not experiencing difficulties, there is no need to download a more recent
firmware version, unless the version has a new feature that you want to use.
2) When you upgrade the router's firmware, you may lose its current configurations, so
please back up the router’s current settings before you upgrade its firmware.
3) Do not turn off the router or press the Reset button while the firmware is being upgraded.
4) The router will reboot after the upgrading has been finished.
4.13.3 Factory Defaults
Choose menu “System Tools→Factory Defaults”, you can restore the configurations of the
Router to factory defaults on the screen (shown in Figure 4-69).
67
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Figure 4-69
Click the Restore button to reset all configuration settings to their default values.
Note:
)
1) The default User Name is admin.
2) The default Password is admin.
3) The default IP Address is 192.168.1.1.
4) The default Subnet Mask is 255.255.255.0.
All settings you have saved will be lost when the default settings are restored.
4.13.4 Backup and Restore
Choose menu “System Tools→Backup and Restore Config”, you can save the current
configuration of the Router as a backup file and restore the configuration via a backup file (shown
Figure 4-70
To back up the Router’s current settings:
68
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Figure 4-71
Figure 4-72
To restore the Router’s settings:
Step 1: Click the Browse button to locate the update file for the device, or enter the exact path
to the Setting file in the text box.
Step 2: Click the Restore button to complete.
4.13.5 Reboot
Choose menu “System Tools→Reboot”, click the Reboot button to reboot the router via the next
69
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
screen.
Figure 4-73
Note:
)
Some settings of the router will take effect only after rebooting, which include:
1) Change LAN IP Address. (System will reboot automatically)
2) MAC Clone (system will reboot automatically)
3) DHCP service function.
4) Static address assignment of DHCP server.
5) Web Service Port of the router.
6) Upgrade the firmware of the router (system will reboot automatically).
7) Restore the router's settings to factory default (system will reboot automatically).
4.13.6 Password
Choose menu “System Tools→Password”, you can change the factory default user name and
Save button.
Figure 4-74
Note:
)
1) It is strongly recommended that you change the factory default user name and password
of the router. All users who try to access the router's web-based utility will be prompted
for the router's user name and password.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
2) The new user name and password must not exceed 14 characters in length and must
not include any spaces. Enter the new Password twice to confirm it.
3) You can click the Clean All button to clean all the configurations.
4.13.7 System Log
Choose menu “System Tools→System Log”, you can view the logs of the Router.
Figure 4-75
The router can keep logs of all traffic. You can query the logs to find what happened to the router.
Click the Refresh button to refresh the logs.
Click the Clean All button to clean all the logs.
4.13.8 Remote Management
Choose menu “Security→Remote Management”, you can configure the Remote Management
from a remote location via the Internet.
Figure 4-76
¾
Web Management Port - Web browser access normally uses the standard HTTP service
port 80. This router’s default remote management web port number is 80. For greater
security, you can change the remote management web interface to a custom port by
71
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
entering that number in the box provided. Choose a number between 1024 and 65534, but
do not use the number of any common service port.
¾
Remote Management IP Address - This is the current address you will use when
accessing your router from the Internet. The default IP address is 0.0.0.0. It means this
function is disabled. To enable this function, change the default IP address to another IP
address as desired.
Note:
)
1) To access the router, you will type your router's WAN IP address into your browser's
address (in IE) or Location (in Navigator) box, followed by a colon and the custom port
number. For example, if your Router's WAN address is 202.96.12.8, and the port number
asked for the router's password. After successfully entering the username and password,
you will be able to access the router's web-based utility.
2) Be sure to change the router's default password to a very secure password.
4.13.9 Statistics
Choose menu “System Tools→Statistics”, you can view the statistics of the Router. This screen
current traffic of the last “Packets Statistic interval” seconds.
Figure 4-77
¾
¾
¾
Current Statistics Status - Enable or Disable the statistics function. The default status is
disabled. Click the Enable button to use the function. Click the Disable button to disable the
function.
Packets Statistics Interval - The default value is 10. Select a value between 5 and 60
seconds in the pull-down list. The Packets Statistic interval value indicates the time section of
the packets statistic.
Sort Rules - Select the rule for displaying the traffic information.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
¾
Statistics Table - This table displays the statistics information about the traffic.
IP Address
The IP address whose statistics information are displayed
MAC Address
The total amount of packets received and transmitted by the router
The total amount of bytes received and transmitted by the router
The total amount of packets received and transmitted in the last “Packets
Statistic interval” seconds
Packets
Bytes
Total
Packets
Bytes
The total amount of bytes received and transmitted in the last “Packets
Statistic interval” seconds
The total amount of the ICMP packets transmitted to WAN in the last
“Packets Statistic interval” seconds
Current
ICMP Tx
UDP Tx
The total amount of the UDP packets transmitted to WAN in the last
“Packets Statistic interval” seconds
The total amount of the TCP SYN packets transmitted to WAN in the last
“Packets Statistic interval” seconds
TCP SYN
Tx
Note:
)
1) If the Current Statistics Status function is disabled, the DoS protection in Advanced
Security will be ineffective.
2) Select the Auto-refresh, then the traffic information will be refreshed automatically
during the Packets Statistics Interval. Click the Refresh button to refresh the information
in the table immediately.
Click the Auto-refresh checkbox to refresh automatically.
Click the Refresh button to refresh immediately.
Click the Reset All button to recount again.
Click the Delete All button to delete all the number.
4.13.10 WAN Speed Detect
Choose menu “System Tools→WAN Speed Detect”, you can detect the wan speed of the router
in the screen below. There are three detecting ways: ICMP DETECT, TCP DETECT, UDP
DETECT. The detect way is the router sends datagram to destination ip address, and then counts
the interval between sending the datagram and receiving the response.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Figure 4-78
¾
¾
¾
¾
¾
Destination IP - the IP address which datagrams are sent to, such as- 202.96.134.188.
ID - The number of ICMP datagrames to be sent.
Source Port - The port where datagrams are sent to, such as- 5000
Destination Port - The datagrams' distination port, such as-6000.
UDP Data - The data carried when sent UDP detect datagram, take care if in the UDP data
to be a domain name, DNS datagram will be sent, at this time, no matter what the destination
port is, the destination port in the sent datagram is always 53. If not, it will be sent as a whole
74
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
UDP datagram.
Detect Result - The interval between sending datagram and recving datagram, uint is ms.
¾
4.13.11 IP NAT Table
Choose menu “System Tools→IP NAT Table”, you will see the IP NAT in the table below:
Figure 4-79
¾
¾
¾
¾
Out Link - The WAN port which links the router.
Protocol Type - The protocol which is used in the link.
IP address - The local or remote IP address to be examined.
Show - To examine the information which the local or remote IP address equals that you
input.
¾
¾
Refresh - To get the latest status and settings of the router
Per page - To set how many information entries a page show.
4.13.12 NAT Source Port Settings
Choose menu “System Tools→NAT Source Port Settings”, you can configure the rang of
exterior port for NAT.
Figure 4-80
Click the Restore button to restore the setting to default value- 1040-65500.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Appendix A: Specifications
General
IEEE 802.3, 802.3u , 802.3x, 802.1x
Standards and Protocols
TCP/IP, PPPoE, DHCP, ICMP, NAT, SNTP,HTTP,DNS
Safety & Emission
Ports
FCC、CE
Two 10/100M Auto-Negotiation WAN RJ45 port.
Eight 10/100/1000M Auto-Negotiation LAN RJ45 ports (Auto
MDI/MDIX)
One SFP Module
One Console (RS232 DB9 Male)
10BASE-T: UTP category 3, 4, 5 cable (maximum 100m)
EIA/TIA-568 100Ω STP (maximum 100m)
100BASE-TX: UTP category 5, 5e cable (maximum 100m)
EIA/TIA-568 100Ω STP (maximum 100m)
1000Base-T: UTP category 5, 5e cable (maximum 100m)
Cabling Type
1000Base-SX: 62.5 u m
50 u m
multi fiber
multi fiber
multi fiber
multi fiber
(maximum 275m)
(maximum 550m)
(maximum 550m)
(maximum 550m)
1000Base-LX: 62.5 u m
50 u m
Physical and Environment
0℃~40℃ (32℉~104℉)
Working Temperature
Working Humidity
10% - 90% RH, Non-condensing
76
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Appendix B: FAQ
1. How do I configure the router to access Internet by ADSL users?
Step 1: First, configure the ADSL modem in RFC1483 bridge model.
Step 2: Connect the Ethernet cable from your ADSL modem to the WAN port on the router. The
telephone cord plugs into the Line port of the ADSL modem.
Step 3: Login to the router, click the menu Network→WAN on the left of your browser. On the
WAN screen, select “PPPoE” for the type of WAN connection. Then enter the user name
and password in the corresponding field, and finish it by clicking Connect.
Figure B-1
Step 4: If your ADSL lease is in “pay-according-time” mode, select “Connect on Demand” or
“connect Manually” or “Time-based Connecting” for Internet connection mode. Type
an appropriate number for “Max Idle Time” or “Period of Time” to avoid wasting paid
time. Otherwise, you can select “Connect Automatically” for Internet connection mode.
Figure B-2
Note:
)
1) Sometimes the connection can not be disconnected although you specify a time to Max
Idle Time, because some applications still visit the Internet continually in the background.
2) If you are a Cable user, please configure the router following the above steps.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
2. How do I configure the router to access Internet by Ethernet users?
Step 1: Login to the router, click the menu Network→WAN on the left of your browser, On the
WAN screen, select “Dynamic IP” for "WAN Connection Type", and finish it by clicking
Save.
Step 2: Some ISPs require that you register the MAC address of your adapter, which is
connected to your cable or DSL modem during installation. If your ISP requires MAC
register, login to the router and click the menu Network→MAC Clone. On the MAC
Clone screen, if your PC’s MAC address is a proper MAC address, click the "Clone MAC
Address" button and your PC’s MAC address will be filled in the "WAN MAC Address"
field; Or else, enter the specific MAC address into the "WAN MAC Address" field
manually. Then click the Save button. It will take effect after rebooting.
Figure B-3
3. I want to use Netmeeting, what do I need to do?
If you start Netmeeting as a sponsor, you don’t need to do anything with the router.
If you start as a responsor, you need configure Virtual Server or DMZ Host as follows:
Method one: Use Virtual Server
Login to the router, click the menu Forwarding→Virtual Servers. On the Virtual Server screen,
add a Virtual Server rule as shown in the next screen: configure 1720 as the “Service Port” and
enter your IP address (assuming 192.168.1.102 for an example), then click select the status
Enabled and click Save.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Figure B-4
Note:
)
Your opposite side should call your WAN IP, which is displayed on the “Status” page.
Method two: Use DMZ Host
Login to the router, click the menu Forwarding→DMZ. On the DMZ screen, select “Enable”, and
enter your IP address into the “DMZ Host IP Address” field (using 192.168.1.102 as an example),
then to click the Save button.
Figure B-5
7. I want to build a WEB Server on the LAN, what should I do?
Because the WEB Server port 80 will interfere with the WEB management port 80 on the router,
you must change the WEB management port number to avoid interference. And then add a WEB
Server on your LAN. You can follow the steps below to proceed.
Step 1: To change the WEB management port number: Login to the router, click the menu
Security→Remote Management. On the Remote Management screen, enter a port
number except 80 (such as 88) into the "Web Management Port" field. Click Save and
the router will reboot.
79
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Figure B-6
Note:
)
If the above configuration takes effect, you should login the Router by entrying
http://192.168.1.1:88 (the router’s LAN IP address: Web Management Port) in the address field of
the web browser.
Step 2: To add a WEB Server: Login to the router, click the menu Forwarding→Virtual Servers
on the left of your browser, On the Virtual Server screen, add a Virtual Server rule as
shown in the next screen: configure “80” as the “Service Port”, and enter your IP
address (assuming 192.168.1.188 for an example), remember to “Enable” and “Save”.
Figure B-7
80
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-R4299G
Dual-WAN SMB Broadband Router User Guide
Appendix C: Glossary
¾
¾
¾
¾
DDNS (Dynamic Domain Name System) - The capability of assigning a fixed host and
domain name to a dynamic Internet IP address.
DHCP (Dynamic Host Configuration Protocol) - A protocol that automatically configure the
TCP/IP parameters for the all the PCs that are connected to a DHCP server.
DMZ (Demilitarized Zone) - A Demilitarized Zone allows one local host to be exposed to the
Internet for a special-purpose service such as Internet gaming or videoconferencing.
DNS (Domain Name Server) - An Internet Server that translates the names of websites into
IP addresses.
¾
¾
Domain Name - A descriptive name for an address or group of addresses on the Internet.
DoS (Denial of Service) - A hacker attack designed to prevent your computer or network
from operating or communicating.
¾
DSL (Digital Subscriber Line) - A technology that allows data to be sent or received over
existing traditional phone lines.
¾
¾
ISP (Internet Service Provider) - A company that provides access to the Internet
MTU (Maximum Transmission Unit) - The size in bytes of the largest packet that can be
transmitted.
¾
¾
NAT (Network Address Translation) - NAT technology translates IP addresses of a local area
network to a different IP address for the Internet.
PPPoE (Point to Point Protocol over Ethernet) - PPPoE is a protocol for connecting remote
hosts to the Internet over an always-on connection by simulating a dial-up connection.
81
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Thermo Products Furnace OH65FA072D48B User Manual
Toshiba Flat Panel Television VX1A00054000 User Manual
Toshiba Oxygen Equipment ST A10 User Manual
TP Link Network Card TP PA2010P User Manual
Tripp Lite Network Card N490 016 STSC User Manual
Uniden Conference Phone FP203 User Manual
Venturer Portable DVD Player PVS6370 User Manual
ViewSonic Car Video System VS15103 User Manual
ViewSonic Projector PJ600 1 User Manual
Villaware Crepe Maker Crpe Maker User Manual