OPERATING INSTRUCTIONS
LINE ARRAY SPEAKER
SR-A12L, SR-A12S, SR-A18B,
SR-A12LWP, SR-A12SWP
RIGGING FRAME
SR-RF12, SR-RF12WP
SR-TP12
TILT JOINT PLATE
Note that casters must be prepared separately.
Thank you for purchasing TOA’s Line Array speaker system, Rigging Frame and Tilt Joint Frame.
Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.
Download from Www.Somanuals.com. All Manuals Search And Download.
1. SAFETY PRECAUTIONS
• Before installation or use, be sure to carefully read all the instructions in this section for correct and safe
operation.
• Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or
cautions regarding safety.
• After reading, keep this manual handy for future reference.
Safety Symbol and Message Conventions
Safety symbols and messages described below are used in this manual to prevent bodily injury and property
damage which could result from mishandling. Before operating your product, read this manual first and
understand the safety symbols and messages so you are thoroughly aware of the potential safety hazards.
Indicates a potentially hazardous situation which, if mishandled, could
result in death or serious personal injury.
WARNING
Indicates a potentially hazardous situation which, if mishandled, could
result in moderate or minor personal injury, and/or property damage.
CAUTION
• (SR-A12LWP, SR-A12SWP, SR-RF12WP only)
When installing the unit in a snowy area, take
appropriate measures to prevent snow from lying
WARNING
on the unit. If the snow lies on the unit, the unit may
• Avoid installing or mounting the unit in unstable
fall, causing personal injuries.
locations, such as on a rickety table or a slanted
surface. Doing so may result in the unit falling
• Owing to the unit's size and weight, be sure that at
down and causing personal injury and/or property
least two persons are available to install the unit.
damage.
Failure to do so could result in personal injury.
• Refer all installation work to the dealer from whom
• Do not use other methods than specified to mount
the speaker was purchased. Installation for flying
the bracket. Extreme force is applied to the unit
requires extensive technical knowledge and
and the unit could fall off, possibly resulting in
experience. The speaker may fall off if incorrectly
personal injuries.
installed, resulting in possible personal injury.
• Use nuts and bolts that are appropriate for the
ceiling's or wall's structure and composition. Failure
• Flying Precautions
Be sure to follow the instructions below. Otherwise,
to do so may cause the speaker to fall, resulting in
the suspension wires or belts may be off or snap
material damage and possible personal injury.
and the speaker may fall off, causing personal
injury.
• Tighten each nut and bolt securely. Ensure that the
bracket has no loose joints after installation to
· Check to confirm that the suspension wires and
prevent accidents that could result in personal
belts are strong enough to withstand the speaker
injury.
load.
· The connectors of the suspension wires and belts
• Use only the specified mounting brackets. Doing
must be securely linked with those of the
otherwise may cause the unit or component to fall
off, resulting in personal injury.
speaker.
· All parts and components (such as enclosures,
metal pieces, and screws) must be free from any
• Do not mount the unit in locations exposed to
deformation, crack, and corrosion.
constant vibration. The mounting bracket can be
· Be sure to use screws supplied with the optional
damaged by excessive vibration, potentially
flying hardware when installing the speaker using
causing the unit to fall, which could result in
such hardware.
personal injury.
• Install the unit only in a location that can
structurally support the weight of the unit and the
mounting bracket. Doing otherwise may result in
the unit falling down and causing personal injury
and/or property damage.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
• Do not operate the unit for an extended period of
time with the sound distorting. This is an indication
of a malfunction, which in turn can cause heat to
generate and result in a fire.
CAUTION
• When unpacking or moving the unit, be sure to
handle it with two or more persons. Falling or
dropping the unit may cause personal injury and/or
property damage.
• Do not stand or sit on, nor hang down from the unit
as this may cause it to fall down or drop, resulting
in personal injury and/or property damage.
• Avoid placing the unit in a doorway or other high
traffic area as people may trip on the equipment
and cords, or be injured by falling objects.
• Have the unit checked periodically by the shop
from where it was purchased. Failure to do so may
result in corrosion or damage to the speaker or its
mounting bracket that could cause the speaker to
fall, possibly causing personal injury.
• Avoid touching the unit's sharp metal edge to
prevent injury.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
2. GENERAL DESCRIPTION
TOA’s SR-A series Line Array speaker employ unique wave front control technology to create a sound field
with high sound clarity and uniform sound pressure. The lineup features types with vertical directivity angles of
5 degrees and 15 degrees, as well as subwoofers. Optional components include the Rigging Frame required
for installation and the Tilt Joint Plates that allow stacked speakers to be tilted downward, permitting speaker
systems to be customized for a wide variety of permanent installation applications.
3. FEATURES
• TOA’s unique wave front control technology permits the linearly arranged speakers to produce a uniform,
interference-free high-frequency sound field offering high sound clarity and excellent long distance sound
transmission capability.
• The SR-A12L(WP) Line Array speaker is a 2-way multi-amplifier driven speaker system featuring a 30 cm
high power output woofer and 2 compression drivers. It features 5 degrees of vertical directivity and 90
degrees of horizontal directivity, and is best suited to long-distance sound transmission applications.
• The SR-A12S(WP) Line Array speaker is a 2-way multi-amplifier driven speaker system featuring a 30 cm
high power output woofer and 2 compression drivers. It features 15 degrees of vertical directivity and 90
degrees of horizontal directivity, and is best suited to short-distance sound transmission applications.
• Combining the long-distance SR-A12L(WP) with the short-distance SR-A12S(WP) permits construction of
Line Array speaker systems to meet a wide range of applications.
• The SR-A18B Subwoofer employs a large-diameter 46 cm woofer unit for high power handling capability,
and is designed to be used in conjunction with the SR-A12L or SR-A12S Line Array speakers.
• Maintenance can be performed from the rear of the enclosure.
• Line Array speakers and sub-woofers can be joined vertically using the supplied Joint Plates. When joined,
directivity can be freely adjusted, with overlapping angles between speakers set to between 0 and 5
degrees, in 1-degree units.
• The SR-RF12 Rigging Frame permits the Line Array speakers to be arranged in flying or stacked
configurations. The SR-A12LWP and SR-A12SWP Line Array speakers can also be installed outdoors in
flying configurations using the SR-RF12WP frame.
• When stacking Line Array speakers with the Rigging Frame, the downward angle can be increased by up to
10 degrees if the SR-TP12 Tilt Joint Plate is additionally used, allowing more appropriate coverage areas to
be set.
• The SR-A12LWP and SR-A12SWP are in full conformity with IPX4 Standards, and can be installed
outdoors. For outdoor installation conditions, refer to page 17; “Notes on Outdoor Installation” of this manual.
4. DIMENSIONS
SR-A12L
Unit: mm
Input panel
(Rear)
Joint plate (accessory)
740
716
Flying plate (Front)
469
Flying plate (Rear)
(Left Side)
(Front)
(Right side)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SR-A12S
Unit: mm
Input panel
(Rear)
Joint plate (accessory)
740
716
Flying plate (Front)
467
Flying plate (Rear)
(Right side)
(Left Side)
(Front)
SR-A18B
Unit: mm
Input panel
Joint plate (accessory)
Flying plate (Front)
(Rear)
740
716
698
Flying plate (Rear)
(Right side)
(Left Side)
(Front)
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SR-A12LWP
Input panel
Unit: mm
Joint plate (accessory)
(Rear)
740
716
Flying plate (Front)
Green LOW (+)
Black LOW (-)
Red HIGH (+)
White HIGH (-)
469
Flying plate (Rear)
(Left Side)
(Front)
(Right side)
Air Hole (Bottom only)
(Bottom)
SR-A12SWP
Input panel
Unit: mm
Joint plate (accessory)
Flying plate (Front)
(Rear)
740
716
Green LOW (+)
Black LOW (-)
Red HIGH (+)
White HIGH (-)
467
Flying plate (Rear)
(Left Side)
(Front)
(Right side)
Air Hole (Bottom only)
(Bottom)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SR-RF12, SR-RF12WP
Caster Mounting Plate
16-M10
Unit: mm
105
164
595
21-ø20
180
71
95
140
(Left side)
(Top)
716
(Right side)
6
6
(Front)
728
(Bottom)
SR-TP12
Unit: mm
484
8
Download from Www.Somanuals.com. All Manuals Search And Download.
5. INPUT CONNECTORS
SR-A12L, SR-A12S and SR-A18B (for Indoor use)
Figures below show the input connector arrangements of each speaker system. Since connector and screw
terminal are internally connected in parallel, either connector can be used for connection.
SR-A12L, SR-A12S
SR-A18B
The NEUTRIK NL4MP connector’s pins are wired as shown below.
Pin No.
1+
SR-A12L, SR-A12S
LOW +
SR-A18B
INPUT +
1-
LOW -
INPUT -
2+
2-
HIGH +
HIGH -
THROUGH
THROUGH
The connector (connection cable side) suited to the NEUTRIK NL4MP is the NEUTRIK NL4FC.
SR-A12LWP and SR-A12SWP (for outdoor use)
Figure below shows the speaker cable arrangement of each speaker system.
Green LOW (+)
Black LOW (-)
Red HIGH (+)
White HIGH (-)
9
Download from Www.Somanuals.com. All Manuals Search And Download.
6. INTERNAL WIRING DIAGRAM
Figures below show the internal wirings of each speaker system.
SR-A12L, SR-A12S
LOW +
LOW
HIGH +
HIGH
1+
2+
1+
2+
-
2-
2
-
1-
1-
-
SR-A12LWP, SR-A12SWP
Green
LOW +
Black
LOW
HIGH +
HIGH
-
Red
White
-
Speaker cable
SR-A18B
INPUT +
INPUT
1+
2+
1+
2+
-
2-
2
-
1-
1-
THROUGH
THROUGH
7. CONNECTIONS
System using the SR-A12L, SR-A12S, SR-A12LWP or SR-A12SWP
SR-A12L, SR-A12S,
SR-A12LWP, SR-A12SWP
Mixer/Pre-amplifier
Digital Processor
LOW
Power Amplifier
LOW
HIGH
HIGH
System which combines the SR-A12L or SR-A12S with the SR-A18B
SR-A12L, SR-A12S
Mixer/Pre-amplifier
Digital Processor
LOW
Power Amplifier
LOW
HIGH
HIGH
S-LOW
SR-A18B
10
Download from Www.Somanuals.com. All Manuals Search And Download.
8. DIGITAL PROCESSOR SETTINGS
Recommended setting parameters are as follows.
System using the SR-A12L, SR-A12S, SR-A12LWP or SR-A12SWP
Filter
Freq. (Hz)
Gain
(dB)
Delay
(msec)
Channel
LOW
Polarity
Normal
TYPE
HPF (12 dB)
LPF (12 dB)
LPF (12 dB)
PEQ
Gain (dB)
Q
40
1.0k
1.0k
300
0.900
0.707
0.707
2.549
2.549
0.707
1.011
1.414
1.160
0
0
0.708
-5.0
PEQ
530
-
4.5
HPF (12 dB)
PEQ
1.2k
2.5k
5.0k
14.0k
HIGH
Inverse
0
-10.0
PEQ
-
2.0
9.0
PEQ
System which combines the SR-A12L or SR-A12S with the SR-A18B
Filter
Freq. (Hz)
Gain
(dB)
Delay
(msec)
Channel
S-LOW
Polarity
Inverse
TYPE
LPF (12 dB)
LPF (12 dB)
HPF (12 dB)
HPF (12 dB)
PEQ
Gain (dB)
Q
90
200
20
0.707
1.000
0.707
1.505
1.800
0.900
0.707
0.707
2.549
2.549
0.707
1.011
1.414
1.160
3.0*
0.708
0.708
0
35
34.5
77.5
1.0k
1.0k
300
530
1.2k
2.5k
5.0k
14.0k
6.0
HPF (12 dB)
LPF (12 dB)
LPF (12 dB)
PEQ
LOW
HIGH
0
Normal
Inverse
-
-
5.0
4.5
PEQ
HPF (12 dB)
PEQ
0
-10.0
PEQ
-
2.0
9.0
PEQ
* The Gain on the S-LOW channel needs to be adjusted depending on the system configuration.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
9. FLYING
9.1. General Description
Use the SR-RF12(WP) Rigging Frame for flying the Line Array speaker. With the use of the SR-RF12(WP), up
to 8 Line Array speakers can be arranged in flying configuration. The SR-A18B Subwoofer system is counted
as 1.5 pieces. When joining two or more speakers, or joining the rigging frame and the speaker, use the Joint
Plate supplied with the speaker. Basic flying system is shown below.
Rigging frame
SR-A18B
Joint plate
(supplied with the SR-A18B)
Joint plate
(supplied with the SR-A12L)
SR-A12L
Joint plate
(supplied with the SR-A12S)
SR-A12S
The vertical directivity angle of the Line Array speaker is 5 degrees for the SR-A12L(WP) and 15 degrees for
the SR-A12S(WP).
SR-A12L(WP)
SR-A12S(WP)
15 degrees
5 degrees
12
Download from Www.Somanuals.com. All Manuals Search And Download.
This flying system is made up of four SR-A12L speakers, two SR-A12S speakers, and one SR-A18B speaker.
To transmit sound over long distances, the four SR-A12Ls are given overlapping angles of 4, 2, and 1 degree,
resulting in a total vertical directivity angle of 43 degrees. The overlapping angle can be adjusted by means of
the Joint Plates used to join the speakers. The horizontal directivity angle is fixed at 90 degrees.
SR-A18B
Enclosure opening angle:
4 degrees
SR-A12L
Overlapping angle:
4 degrees
5 degrees
Enclosure opening angle:
2 degrees
SR-A12L
Overlapping angle:
2 degrees
Enclosure opening angle:
1 degree
5 degrees
SR-A12L
Overlapping angle:
1 degree
5 degrees
SR-A12L
5 degrees
SR-A12S
15 degrees
15 degrees
SR-A12S
43 degrees
As can be seen in the accompanying figure, the overlapping angle equals the rear-opening angle between
enclosures.
[Example] To adjust the sound radiation-overlapping angle to 5 degrees, set the rear-opening angle between
enclosures to 5 degrees.
No sound overlapping angle is created if speakers are joined without space provided between enclosures.
9.2. SR-RF12(WP) Rigging Frame assembly
For assembling, refer to the figure below. Tighten 3 supplied bolts with plain washers and spring washers
securely to fix each Mounting Plate to the rigging frame.
Mounting Plate, Front A
Mounting Plate, Rear A
Rigging frame
Finished
assembly diagram
Mounting Plate, Front B
Mounting Plate, Rear B
13
Download from Www.Somanuals.com. All Manuals Search And Download.
9.3. Joining the Enclosure to the Rigging Frame
Flying Plates are mounted at both the front and rear of the enclosure’s sides. Follow the procedure below to
mount the enclosure to the Rigging Frame, as shown in the assembly diagrams.
Fix a supplied Joint Plate securely to the left side of the Rigging Frame and another to the right side of the
enclosure, each using 4 supplied bolts with plain washers and spring washers.
Before securing the Joint Plate, determine whether the enclosure’s horn will face right or left. (This is not
required for the SR-A18B Subwoofer.) When suspending the subwoofer, install the system so that the
subwoofer is positioned at the top (directly below the Rigging Frame).
High box assembly diagram
Subwoofer assembly diagram
Joint plate
Joint plate
Joint plate
Joint plate
Flying plate
Flying plate
Join the enclosure to the Rigging Frame securely, using 4 supplied bolts with plain washers and spring
washers on each side. For Joint Plate mounting holes, use the hole that creates an overlapping angle of 0
degree. Refer to the assembly diagrams below.
High box finished assembly diagram
(Left side)
(Right side)
Subwoofer finished assembly diagram
(Left side)
(Right side)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
9.4. Joining Enclosures
Use the supplied Joint Plate to join the enclosures by way of the enclosure's flying plate. As shown in the
figure, mount a Joint Plate securely to the upper enclosure's lower left side, using 4 supplied bolts with plain
washers and spring washers. Similarly, attach another Joint Plate to the lower enclosure's upper right side.
Joint Plate
Joint Plate
Join the enclosures securely, using 4 supplied bolts with plain washers and spring washers on each side.
Because the Joint Plate has holes to be used for setting the overlapping angle, use the holes that provide the
desired overlapping angle. The overlapping angle can be set to between 0 and 5 degrees in 1-degree units.
Joint Plate
Enclosure
opening angle:
5 degrees
Enclosure
opening angle:
0 degree
Overlapping angle:
5 degrees
Overlapping angle: 0 degree
15
Download from Www.Somanuals.com. All Manuals Search And Download.
9.5. Notes on Flying
•
•
•
Check to confirm that the suspension wires, belts, construction of the
ceiling, etc are strong enough to withstand the speaker load.
Tighten each joint bolt to 300-350 kg·cm of torque securely.Be sure to
use the joint bolts supplied with the speaker and the Rigging Frame.
Up to 8 Line Array speakers can be arranged in flying configuration
per one Rigging Frame. The Subwoofer is counted as 1.5 pieces. No
more than 8 speakers can be arranged in flying configuration.
WARNING
• Fly the assembled system vertically from at least at
two points on the left and right sides.
• Use a suspension point that provides the desired
downward angle. The downward angle increases
as the suspension point is moved backward.
Center of
gravity position
• Add anti-swing guy wires as needed. Take care not
to apply the enclosure’s weight on the guy wires.
Anti-swing guy wires
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes on Outdoor Installation
•
In case of outdoor installation, follow the notes mentioned below.
WARNING
• Only the SR-A12SWP or SR-A12LWP Line Array speaker can be installed outdoors. There is no Subwoofer
available to be installed outdoors.
• WP type speaker features the water protection construction (IPX4), however install it under roofs, eaves, or
other locations not directly exposed to rain or snow.
• Install the speaker so that its air hole is positioned downward, causing the horn face to the right as shown
below.
Air Hole
• The installation angle of the speaker’s top panel must be between 0 degree from the horizontal axis and up
to 50 degrees downward.
Horizontal axis:
0 degree
50 degrees
• Use the SR-RF12WP Rigging Frame.
• Never suspend the SR-RF12WP Rigging Frame with wires. Be sure to fix it securely to the constructions
with mounting hardware.
• When permanently installing the speaker outdoors, inspect it periodically.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
10. STACKING
10.1. General Description
Line Array speakers can be stacked using the SR-RF12 Rigging Frame. Up to 5.5 speakers can be stacked,
counting each Line Array speaker as 1 piece and each SR-A18B Subwoofer as 1.5 pieces. Shown below is a
basic stacked system. Note that casters must be prepared separately.
SR-A12L
Joint Plate
SR-A18B
Rigging Frame
Caster (required by the user)
This stacking system is made up of four SR-A12L speakers, and one SR-A18B speaker. The directivity
characteristic is 20 degrees vertically and 90 degrees horizontally. The overlapping angles are all set at 0 degree.
10.2. SR-RF12 Rigging Frame assembly
Select the positions of the mounting plates and assemble keeping the stacked system’s center of gravity in
mind. Tighten 3 supplied bolts with plain washers and spring washers securely to fix each Mounting Plate to
the rigging frame.
Assembly diagram
Mounting Plate, Rear B
Mounting Plate,
Front B
Rigging frame
Mounting Plate, Rear A
Mounting Plate, Front A
When attaching the Mounting Plates
to the center positions
When attaching the Mounting
Plates forward positions
Mounting Plate attaching position
Mounting Plate attaching position
Attach the casters, of which specifications are as follows, as the Rigging Frame’s leg. Casters and caster
mounting bolts are required by users.
Caster Specification
Wheel size:
Top plate overall size: 95 mm x 95 mm
100 mm or more
Bolt hole spacing: 71 mm x 71 mm
Attaching bolt size: M10
Loaded mass:
With stopper
Total mass (mass of rigging frame + mass of speaker) x 50% or more per caster
18
Download from Www.Somanuals.com. All Manuals Search And Download.
10.3. Mounting the Enclosure to the Rigging Frame
Flying Plates are mounted to the front and rear of the enclosure’s sides. Follow the procedures below to
mount the enclosure to the Rigging Frame, as shown in the assembly diagrams.
Fix a supplied Joint Plate securely to the right side of the Rigging Frame, and another Joint Plate to the left
side of the enclosure, each using 4 supplied bolts with plain washers and spring washers. Before securing the
Joint Plate, determine whether the enclosure’s horn will face right or left. (This is not required for the SR-A18B
Subwoofer). When stacking the subwoofer, install the system so that the subwoofer is positioned at the
bottom (directly above the Rigging Frame).
High box assembly diagram
Subwoofer assembly diagram
Join the enclosure to the Rigging Frame securely, using 4 supplied bolts with plain washers and spring
washers on each side (see the assembly diagrams below). For selecting holes in the Joint Plate to be used,
refer to the section “10-6 Tilting the enclosure downward” described later .
High box finished assembly diagram
(Left side)
(Right side)
Subwooter finished assembly diagram
(Left side)
(Right side)
19
Download from Www.Somanuals.com. All Manuals Search And Download.
10.4. Joining Enclosures
For joining enclosures, refer to “9 Flying, 9-4. Joining Enclosures”.
10.5. Notes on Stacking
• Prepare casters and caster mounting bolts separately, as the Rigging Frame’s leg.
• When stacked, the Line Array speaker’s front or rear deviation from the Rigging Frame must be within 10cm.
Also, whenever possible, select mounting plate positions that allow the system’s center of gravity to be
situated near the center of the Rigging Frame.
•
•
Tighten each joint bolt to 300-350 kg·cm of torque securely.Be sure to
use the bolts supplied with the speaker and the Rigging Frame.
Up to 5.5 speakers can be stacked, counting each Line Array speaker
as 1 piece and each SR-A18B Subwoofer as 1.5 pieces. No more
than 5.5 pieces can be stacked.
WARNING
Typical stacking example
The Line Array speaker's front or rear deviation
from the Rigging Frame must be within 10cm.
Forbidden stacking example
10cm or more
20
Download from Www.Somanuals.com. All Manuals Search And Download.
10.6. Tilting the Enclosure Downward
The lower Line Array speaker, excluding the subwoofer, can be tilted downward with the addition of SR-TP12
Tilt Joint Plates. SR-TP12 Tilt Joint Plates make it possible to set wider angles than can be achieved using the
supplied Joint Plates. Replace the lowermost Line Array speaker’s Joint Plates with the Tilt Joint Plates, then
assemble the system.
Joined view with sub-woofer
Joined view with rigging frame
Tilt angle (Vertical facing angle) can be adjusted
Tilt angle (Vertical facing angle) can be adjusted
in the range of 0 degree to 15 degrees.
in the range of 10 degrees to 15 degrees.
Tilt joint plate
Tilt joint plate
For assembling, refer to the previous “10-3. Mounting the Enclosure to the Rigging Frame” when joining to the
rigging frame, and “9 Flying, 9-4. Joining Enclosures” when joining to the sub-woofer.
For precautions when stacking, refer to the previous “10-5, Notes on Stacking”.
SR-TP12 Tilt Joint Plate
Tilt angle (Vertical facing angle) table
When using the supplied
joint plate
When using the optional tilt
joint plate
When joining the joint plate
with rigging frame
0 – 5 degrees
in 1 degree units
10 degrees – 15 degrees
in 1 degree units
When joining the joint plate
with sub-woofer
0 degree – 15 degrees
Same as above
in 1 degree units
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Typical stacking example using the tilt joint plate
SR-A18B x1, SR-A12S x1, SR-A12L x3
SR-A12L
SR-A12S
Vertical facing angle:
0 degree - 15 degrees
SR-A18
Vertical facing angle:
0 degree - 15 degrees
(Left side)
SR-A12S x1, SR-A12L x4
(Right side)
SR-A12L
Vertical facing angle:
10 degrees - 15 degrees
SR-A12S
(Left side)
(Right side)
Vertical facing angle:
10 degrees - 15 degrees
Do not use the Tilt Joint Plate for joining Line Array speakers
(excluding the sub-woofer), for joining the subwoofer to the Rigging
Frame, or in flying systems.
WARNING
22
Download from Www.Somanuals.com. All Manuals Search And Download.
11. SPECIFICATIONS
SR-A12L, SR-A12S
Model
SR-A12L
SR-A12S
Enclosure
Bass-reflex type
Power Handling
Capacity
Continuous program, Low frequency: 450 W, High frequency: 180 W
Rated Impedance
Sensitivity
Low frequency: 8 Ω, High frequency: 16 Ω
Low frequency: 98 dB (1 W, 1 m)
High frequency: 110 dB (1 W, 1 m)
Low frequency: 98 dB (1 W, 1 m)
High frequency: 109 dB (1 W, 1 m)
Frequency Response
Crossover Frequency
50 – 20,000 Hz (when using the optional DP-0206)
1,000 Hz (when using the optional DP-0206)
Horizontal: 90˚, Vertical: 5˚ Horizontal: 90˚, Vertical: 15˚
30 cm Cone type
Coverage Angle
Speaker
Component (low)
Speaker
Component (high)
Wave front control horn 90˚
(horizontal) x 5˚ (vertical)
+ Compression driver x 2
Wave front control horn 90˚
(horizontal) x 15˚ (vertical)
+ Compression driver x 2
Input Connector
Finish
M5 Screw terminal, distance between barriers: 12.2 mm
and NEUTRIK NL4MP x 2 (Suitable connector: NEUTRIK NL4FC)
Enclosure: Plywood, black, Urethane paint
Front grille: Punched steel plate, Black, Acrylic paint
Dimensions
Weight
740 (w) x 433 (h) x 469 (d) mm
49 kg (including accessories)
740 (w) x 433 (h) x 467(d) mm
47 kg (including accessories)
Accessories
Joint plate ...... 2, Joint plate mounting bolt (M10) ...... 16
*The design and specifications are subject to change without notice for improvement.
SR-A12LWP, SR-A12SWP
Model
SR-A12LWP
SR-A12SWP
Enclosure
Bass-reflex type
Power Handling
Capacity
Continuous program Low frequency: 450 W, High frequency: 180 W
Rated Impedance
Sensitivity
Low frequency: 8 Ω, High frequency: 16 Ω
Low frequency: 98 dB (1 W, 1 m)
High frequency: 110 dB (1 W, 1 m)
Low frequency: 98 dB (1 W, 1 m)
High frequency: 109 dB (1 W, 1 m)
Frequency Response
Crossover Frequency
50 – 20,000 Hz (when using the optional DP-0206)
1,000 Hz (when using the optional DP-0206)
Horizontal: 90˚, Vertical: 5˚ Horizontal: 90˚, Vertical: 15˚
30 cm Cone type
Coverage Angle
Speaker
Component (low)
Speaker
Component (high)
Wave front control horn 90˚
(horizontal) x 5˚ (vertical)
+ Compression driver x 2
Wave front control horn 90˚
(horizontal) x 15˚ (vertical)
+ Compression driver x 2
Direct cable withdrawal from internal speaker: 8.6 mm,
Speaker cable
conductor cross section: 1.25 mm2, 4-core cable, 3 m
Water Protection
Finish
IPX4
Enclosure: Plywood, black, Urethane paint
Front grille: Punched stainless steel (SUS304), Black, Paint
Dimensions
740 (w) x 433 (h) x 469 (d) mm
740(w) x 433 (h) x 467 (d) mm
(excluding speaker cable)
(excluding speaker cable)
Weight
51 kg (including accessories)
48 kg (including accessories)
Accessories
Joint plate ...... 2, Joint plate mounting bolt (M10) ...... 16
*The design and specifications are subject to change without notice for improvement.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
SR-A18B
Model
SR-A18B
Enclosure
Bass-reflex type
Power Handling
Capacity
Continuous program: 720 W
Rated Impedance
8 Ω
Sensitivity
95 dB (1 W, 1 m)
Frequency
40 – 400 Hz (when using the optional DP-0206)
Response
Crossover
Frequency
Speaker
80 Hz (when using the optional DP-0206)
46 cm Cone type
Component (low)
Input connectors
M5 Screw terminal, distance between barriers: 12.2 mm
and NEUTRIK NL4MP x 2 (Suitable connector: NEUTRIK NL4FC)
Enclosure: Plywood, black, Urethane paint
Finish
Front grille: Punched steel plate, Black, Acrylic paint
Dimensions
Weight
740 (w) x 573 (h) x 698 (d) mm
66 kg (including accessories)
Accessories
Joint plate ...... 2, Joint plate mounting bolt (M10) ..... 16
*The design and specifications are subject to change without notice for improvement.
SR-RF12, SR-RF12WP
Model
SR-RF12
Flying: up to 8
Stacking: up to 5.5
SR-RF12WP
Flying: up to 8
Number of
Speakers to be
Mounted
(The SR-A18B (optional) is counted as
1.5 pieces)
Finish
Steel plate, Black, Paint
Stainless steel (SUS304)
Dimensions
Weight
728 (w) x 164 (h) x 800(d) mm (excluding the bolt section)
22 kg (including accessories) 22 kg (including accessories)
Plate mounting bolt (M10) ...... 12
Accessories
*The design and specifications are subject to change without notice for improvement.
SR-TP12
Model
SR-TP12
Variable Angle Range
to be Mounted
When mounted the SR-A18B: 0˚ – 15˚
When mounted the SR-RF12: 10˚ – 15˚
Finish
Steel plate, black, paint
3.2 kg
Weight
*The design and specifications are subject to change without notice for improvement.
133-05-383-8A
Download from Www.Somanuals.com. All Manuals Search And Download.
|