®
T2265
SprintPro
T2280
SprintPro
Operator’s manual
Matrix printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick start-up
Table of contents
Table of contents
Operator’s Manual
QUICK START-UP
Introduction
2
2
2
3
3
3
3
Symbols used
Important safety instructions
Using the Online-CD-ROM
Contents of the Online CD-ROM
Hardware requirements
Troubleshooting
Printer at a glance
4
Installation
5
5
6
7
7
Unpacking the printer
Placing your printer
Connecting the printer
Switching on the printer
Control panel
Online mode
Offline mode
Setup mode
8
8
8
8
Changing the ribbon cassette
9
Paper handling
14
14
15
15
17
18
19
Changing the paper type
Loading paper
Fanfold paper
Single sheets
Paper transport
Moving the paper to the tear position
Settings
20
20
21
22
23
Setting the tear position
Setting the first printing line (TOF)
Setting the print head gap
Selecting character density and font
Technical data
24
24
25
Printer specifications
Paper specifications
Accessories
26
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Quick start-up
Introduction
This Operator’s Manual is intended as a quick introduction into working with the printer and
also to enable inexperienced users to operate the device properly. It describes the most import-
ant functions of the printer and contains the essential information for your everyday work
with the printer. A more detailed description of the printer, its characteristic features, and fur-
ther information is contained in the Reference Manual on the Online CD-ROM, which is in-
serted at the back of this manual.
➤ Symbols used
Important information is highlighted in this manual by two symbols.
CAUTION highlights information which must be observed in order to prevent injuries to the
user and damage to the printer.
STOP
NOTE highlights general or additional information about a specific topic.
➤ Important safety
Read the following instructions thoroughly before starting up your printer in order to prevent
injuries and avoid damage to the device.
instructions
Keep this Operator’s Manual in a place which is easily accessible at all times.
Place the printer on a solid base so that it cannot fall down to the ground.
Do not expose the printer to high temperatures or direct sunlight.
Keep all liquids away from the printer.
Protect the printer from shock, impact and vibration.
Be sure to connect the printer to a socket with the correct mains voltage.
The power supply cable may be damaged if the paper edges constantly chafe the insulating
sheath. The user must always ensure that there is sufficient distance between the power sup-
ply cable and the paper.
Never carry out maintenance or repair work yourself. Always contact a qualified service
technician.
STOP
STOP
Whenever you want to disconnect the printer from the power supply, pull the plug out from
the mains socket.
Additional safety instructions are provided at the relevant places in the text.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick start-up
Introduction
➤ Using the
First install the Adobe Acrobat Reader on your hard disk, unless the program has already
been installed. To install it, follow the steps described in the README file in the READER
directory.
Online-CD-ROM
To start the online documentation, call the File Manager (Windows 3.1) or Explorer
(Windows 95/98, Windows ME, Windows 2000, Windows NT4) and double click on the
START.PDF file. Then follow the instructions and menus on the screen.
➤ Contents of the
The Online CD-ROM contains
– the Reference Manual: A detailed description of the printer and its impressive features
– Drivers: For Windows 3.1, Windows 95/98, Windows ME, Windows 2000, Windows NT4
– Additional documentation: Programming instructions and descriptions of the available
options
Online CD-ROM
If your CD-ROM is be defective or missing, please consult your dealer. The Online Documen-
tation is also available as a hardcopy (at a cost) or can be downloaded via the Internet.
➤ Hardware
Minimum hardware requirements: PC 486 MHS, quad-speed CD-ROM, 15" display screen,
mouse.
requirements
➤ Troubleshooting
The online documentation supplied on the CD-ROM contains detailed information on trouble-
shooting.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Printer at a glance
Quick start-up
Printer at a glance
View from the front
Printer in tractor mode
Control panel
Soundproofing cover
Top cover
Front cover
Bottom cover
Tractors
Power switch
View from the rear
Printer in single-sheet mode
Rear cover
Paper support
Interface
connectors
Power cord connector
Single sheet feeder
Paper guide
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick start-up
Installation
Installation
➤ Unpacking the printer
Place your printer on a solid base.
Make sure that the “Up” symbols point in the correct direc-
tion.
Open the packaging, take out the accessory cassette and un-
pack it. Pull the printer out of the cardboard box towards you
and remove the remaining packaging material.
Check the printer for any visible transport damage and mis-
sing items. In addition to this Operator’s Manual (➀) the CD-
ROM (➁, at the back of this manual), the power cable (➂)
and the ribbon (➃) must be included.
➃
If you find any transport damage or if any accessories are
missing, please contact your dealer.
➂
➁
➀
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Quick start-up
➤ Placing your printer Place the printer on a solid, flat, surface, ensuring that the printer is positioned in such a way
that it can not topple, and that there is easy access to the control panel and paper input
devices. Also ensure that there is sufficient space for the printed output.
If you expect that frequent forward and reverse feeds will
occur, you should place the printer as shown in the figure, if
possible.
When selecting the printer location, observe the following additional instructions:
Never place the printer in the vicinity of inflammable gas or explosive substances.
STOP
Do not expose the printer to direct sunlight. If you cannot avoid placing the printer near a win-
dow, protect it from the sunlight with a curtain.
When connecting a computer to the printer, make sure not to exceed the maximum cable
length (see Reference Manual on the Online CD-ROM, Technical Specifications).
Ensure sufficient distance between the printer and any heating devices/radiators.
Avoid exposing the printer to extreme temperature or air humidity fluctuations. Protect the
printer from dust.
It is recommended to install the printer in a place which is acoustically isolated from the
workplace because of the noise it may produce.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick start-up
Installation
➤ Connecting the printer
Make sure that the printer is set to the correct voltage (e.g.
230 V in Europe, 120 V in the U.S.A.). To do this, check the
plate above the power inlet at the rear of the printer.
If the setting is incorrect, set the coloured switch at the rear
of the printer to the correct position, using a pointed object
(e.g. screwdriver, ball pen or tweezers).
120V
Make sure that the printer is switched off before set-
STOP
ting the correct voltage; otherwise severe damage
may be caused.
Never switch on the printer if the voltage setting is
incorrect, since this may cause severe damage to
the printer.
Make sure that the printer and the computer are switched off,
and connect the printer to the computer with the data cable
(interface cable).
Connect the power cable to the power inlet of the printer.
Connect the power cable plug to a mains socket.
➤ Switching on the printer
The power switch for switching on the printer is located at
the bottom left at the front of the printer when viewed from
the front.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Control panel
Quick start-up
Control panel
The control panel and the keys are used for controlling the printer operation.
The upper line of the display shows whether the printer is in Online or Offline mode and the
paper path selected (Tractor1 or Single).
➤ Online mode
After switching on, the printer is automatically set to online mode. Only in this mode can it
receive data from the computer.
Tear key (4): Activates the tear function when fanfold paper is loaded (see
page 19, Moving the paper to the tear position). If Load is displayed above
this key, no paper is loaded in the printer; press the key to feed paper to the
Online Tractor1
Tear
Online
printing position.
Setup key: Sets the printer to setup mode.
1
2
3
4
Setup
Online key: Sets the printer to offline mode.
➤ Offline mode
Only in this mode is it possible to perform step, line, or form feeds from the control panel (see
page 18, Paper transport); however, data cannot be received.
Park key (1): Clears the paper path with paper loaded and activates paper
path quick selection (see page 14, Changing the paper type).
Key (2): Short keypress: Microstep forward.
Offline Tractor1
Online
Park
Load
Long keypress: Continuous paper feed.
Key (3): Short keypress: Microstep reverse.
1
2
3
4
Setup
Long keypress: Continuous paper reverse feed back to the park position.
Load key (4): If no paper is loaded, see above.
If paper is loaded: Short keypress: Line Feed (LF);
long keypress: Form Feed (FF).
Setup key: Sets the printer to setup mode.
Online key: Sets the printer to online mode.
➤ Setup mode
Adjust Paperway
In this mode, the following settings are available:
Setup key: Sets the printer to setup mode, in which the following
settings can be selected:
Menu key (1): Other menu settings.
Online
Menu
Char
Adjust key (2): Tear position, first printing line and print head gap.
Paperway key (3): Paper path.
1
2
3
4
Setup
Char key (4): Font and number of characters per inch.
Access to the other menu settings (Menu) may be disabled by the manufacturer. For informa-
tion on how to enable access and about the available settings, refer to the Reference Manual
on the Online CD-ROM (chapter The Menu, section Enabling the menu).
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick start-up
Changing the ribbon cassette
Changing the
ribbon cassette
Before opening the cover, make sure that the printer is switched on so that it can execute auto-
matic preparations for ribbon changing (widening the print head gap).
Move the paper to the park position.
Open the printer top cover.
Carefully slide the print head carriage to the left stop (viewed
from the printer front).
The print head becomes hot during printing. For
STOP
this reason, let it cool down before touching it.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the ribbon cassette
Quick start-up
Move the coloured friction tab to the left (direction of the
arrow) as shown in the figure and raise the friction mechan-
ism.
Remove the used cassette.
We recommend use of genuine ribbon cassettes only.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick start-up
Changing the ribbon cassette
Raise the coloured insertion tongue A.
A
Insert the coloured ribbon tension knob into the right-hand
front location of the new ribbon cassette. Turn the knob in the
direction of the arrow in order to take up the slack of the rib-
bon.
Tilt the ribbon cassette slightly forward, and thread in the rib-
bon between the coloured insertion tongue and the ribbon
support (transparent plastic plate).
Align the cassette and insert it, then press down until it clicks
into place.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the ribbon cassette
Quick start-up
Insert the coloured tension knob into one of the two locations.
Turn the tension knob to take up slack in the ribbon until it is
seated correctly at the bottom in the ribbon support.
Press down the coloured insertion tongue A.
A
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick start-up
Changing the ribbon cassette
Move the print head carriage backwards and forwards several
times. If the ribbon is correctly seated, there must be no per-
ceptible resistance.
The ribbon should be transported during the travel
from left to right. If this is not the case, you should
check that the ribbon cassette is correctly inserted
on the right.
Press the friction mechanism down until it clicks into place.
Close the front section of the top cover.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Paper handling
Quick start-up
Paper handling
This section describes how to set the paper type, load fanfold paper and single sheets, trans-
port paper and move the paper to the tear position.
➤ Changing the
You can change the paper type either from an application program, by means of the paper
path quick selection feature or in the Setup menu. In this section, the quick selection feature
is described; for detailed information on how to make this setting via the Setup menu, refer
to the Reference Manual on the Online CD-ROM.
paper type
On some printer models, the single sheet paper source cannot be selected since these models
are not designed for manual single sheet feeding.
Make sure that the printer is in offline mode; press the Online key, if necess-
ary.
Press the Park (1) key. If fanfold paper is loaded in the printer, it is fed to the
Offline Tractor1
Online
Park
Load
tear position. The text tear paper off appears in the display. Then press any
key. If a single sheet is loaded in the printer, it is ejected.
1
2
3
4
Setup
Use one of the marked keys to select the desired paper path, for example,
Single (2).
Single Tractor
Online
If you do not make a selection within 5 seconds, the menu is closed.
1
2
3
4
Setup
The printer returns to offline mode. The display alternates between the basic
menu and the menu in the following figure:
Insert a single sheet (for the procedure, see page 17, Loading single sheets).
Load paper from
Single
Online
1
2
3
4
Setup
Press the Online key to set the printer to ready status. When the printer re-
ceives data from the computer, the single sheet is automatically loaded. Press
the Load (4) key to load the single sheet before starting the printout.
Online Single
Load
Online
1
2
3
4
Setup
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick start-up
Paper handling
➤ Loading paper
Your printer can process both fanfold paper and single sheets. For information on the
supported paper sizes, please refer to page 25 (Paper specifications).
You should only use those paper types which are approved for this printer. For more infor-
mation, please refer to the Reference Manual on the Online CD-ROM.
Fanfold paper
Make sure that the printer is set for fanfold paper printing. If
necessary, change the paper type (see page 14, Changing the
paper type).
Raise the front cover.
Not available on some printer types.
Remove the bottom cover A.
Open the right and left tractor flaps.
A
Release the coloured latch lever of the left-hand tractor and
align the tractor so that the first printing position on the paper
matches the X mark on the printer housing.
Lock the coloured lever again.
Place fanfold paper into the left-hand tractor.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Paper handling
Quick start-up
Open the coloured latch lever of the right-hand tractor and
align it to the paper width.
Insert the fanfold paper into the right-hand tractor.
Make sure that it is inserted by the same length as on the left-
hand tractor in order to avoid any paper jam.
Close the tractor flap and lock the tractor by turning the trac-
tor lever to the rear.
Do not tighten the paper excessively to avoid tear-
ing the perforation holes; do not allow excessive
slack or the paper will not remain flat enough to en-
sure accurate feeding.
Be sure to align the paper stack in parallel with the printer
and that the paper flow is unobstructed.
90
Re-install the bottom cover.
Lower the front cover.
Switch the printer on. The active paper source (Traktor1) appears in the dis-
play. The paper is automatically loaded when the printer is in online mode
and receives data from the computer.
Online Tractor1
Load
Online
Setup
1
2
3
4
Press the Load (4) key to load paper before starting the printout.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick start-up
Paper handling
Single sheets
Some printer models are designed for fanfold paper operation only and therefore do not featu-
re a single sheet feeder. The front cover can therefore not be opened on these models.
Make sure that the printer is set to single sheet mode. If
necessary, change the paper type (see page 14, Changing the
paper type).
Press the latch at the middle of the front cover. The single
sheet input tray opens downwards.
Align the left paper guide with the mark on the left of the
single sheet input tray. Adjust the right paper guide to the
width of the paper used.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Paper handling
Quick start-up
Insert the single sheet as far into the input tray as possible.
Press the Online key to set the printer to ready status.
The sheet is automatically loaded when the printer is in on-
line mode and receives data from the computer. Press the
Load (4) key to load paper before starting the printout.
➤ Paper transport
Loaded paper (fanfold paper/single sheets) can be transported in the printer in several ways.
Make sure that the printer is in offline mode; press the Online key, if
necessary.
Offline Tractor1
Online
Park
LF/FF
Key (2)
1
2
3
4
Setup
Short keypress: Paper is transported upwards step by step.
Long keypress: Continuous transport upwards.
Key (3)
Short keypress: Paper is transported downwards step by step.
Long keypress: Continuous transport downwards.
LF/FF key (4)
Short keypress: Line Feed (LF) is effected.
Long keypress: Form Feed (FF) is effected.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick start-up
Paper handling
➤ Moving the paper to You can use the Tear key to move the paper to the tear position.
the tear position
Swing the soundproofing cover towards the front.
Make sure that the printer is in online mode. If necessary, press the Online
key.
Press the Tear (4) key. The printer moves the perforation edge of the fanfold
paper to the tear edge of the top cover (see below).
Online Tractor1
Online
Setup
Tear
1
2
3
4
The display alternates between…
Tear position
Tractor1
Online
Setup
1
2
3
4
and…
After having torn off the paper, press the Exit (4) key. The printer returns the
paper to the first printing position.
If a print job is active, the printer automatically returns the paper to the first
printing position.
Online
Tear
Exit
Online
Setup
1
2
3
4
Tear edge
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Quick start-up
Settings
This section describes how to set the tear position, the first printing line, the print head gap as
well as the font selection and the character density.
➤ Setting the tear
If the tear position of the paper is not aligned with the tear edge of the top cover of the printer,
you can adjust it.
position
Press the Setup key. The printer changes to setup mode.
Press the Adjust (2) key.
Adjust Paperway
Online
Menu
Char
1
2
2
3
4
Setup
Press the Tear (4) key. The printer performs a form feed.
TOF
Online
Head
Tear
1
3
4
Setup
Press the < (2) or > (3) key to move the perforation to the desired position.
Confirm the input by pressing the Set (1) key.
Confirm the input again by pressing the Setup key. The printer is reset to the
TearAdj= 00/72"*
Set < > Exit
Online
initial status.
1
2
3
4
Setup
The correction made – a maximum of approx. 2.5 cm (1") in each direction – will be retained
after switching the printer off.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick start-up
Settings
➤ Setting the first
You can use the TOF function for setting the position of the first printing line for each paper
source and each menu individually.
printing line (TOF)
Before using the TOF function (if fanfold paper is used), you should first set the tear position
(see above).
Open the top cover.
Press the Setup key. The printer changes to setup mode.
Press the Adjust (2) key.
Adjust Paperway
Online
Menu
Char
1
2
2
3
4
Setup
Press the TOF (3) key. The printer performs a form feed.
TOF
Online
Head
Tear
1
3
4
Setup
The paper is fed to the position where the bottom edge of the
first printing line A is aligned with the tear edge of the top
cover B. The factory setting for the first printing position
(TOF) is 12/72".
B
A
Computerdrucker
Press the < (2) or > (3) key to move the first printing line to the desired posi-
tion. You can set values from 0 to 220/72" for fanfold paper or for single
sheets.
FormAdj= 12/72"*
Set < > Exit
Online
1
2
3
4
Setup
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Quick start-up
Confirm the input by pressing the Set (1) key.
Press the Setup key. The printer returns to the initial status.
FormAdj= 17/72"
Set < > Exit
Online
Setup
1
2
3
4
The setting made will be retained after switching off the printer. For more details, please re-
fer to the Reference Manual on the Online CD-ROM.
➤ Setting the print
The printer features automatic print head gap adjustment to the thickness of the paper used. In
setup mode, you can enter a correction value to modify the head gap that is normally deter-
mined automatically. This correction is useful for modifying the appearance of the type face
and the impact force for multi-layer paper.
head gap
The AGA (automatic gap adjustment) function must be set to On. For more detailed informa-
tion, refer to the Reference Manual on the Online CD-ROM.
Press the Setup key. The printer changes to setup mode.
Press the Adjust (2) key.
Adjust Paperway
Online
Menu
Char
1
2
3
4
Setup
Press the Head (1) key.
TOF
Online
Head
Tear
1
2
3
4
Setup
Use the < (2) or > (3) key to set the range within which the automatic gap ad-
justment is to be corrected. You can select values in the range from -10 to +10.
Confirm the input by pressing the Set (1) key.
Head= 0
Set < > Exit
*
Online
Press the Setup key. The printer returns to the initial status.
1
2
3
4
Setup
Negative values decrease the print head gap, positive values increase it.
The setting made will be retained after switching off the printer.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick start-up
Settings
➤ Selecting character You can use the CPI (= Characters Per Inch) key in setup mode to select the number of char-
acters per inch to be printed. You can use the Font key to select resident fonts.
density and font
Press the Setup key, then the Char (4) key.
Adjust Paperway
Online
Menu
Char
1
2
3
4
Setup
Press the CPI (3) or Font (2) key (in our example, press CPI).
Font CPI
Online
1
2
3
4
Setup
Use the < (2) or > (3) key to set the desired character density. Confirm the se-
lection by pressing the Set (1) key.
You can cancel the selection and leave the setting unchanged by pressing the
10 CPI
Set < > Exit
*
Online
Exit (4) key.
1
2
3
4
Setup
If you pressed the Font (2) key, use the < (2) or > (3) key to select the desired
font. Confirm the selection by pressing the Set key.
You can cancel the selection and leave the setting unchanged by pressing the
ROMAN
Set < > Exit
NLQ
Online
Exit (4) key.
1
2
3
4
Setup
Press the Setup key. The printer returns to the initial status. It is also possible
to press the Online key. The printer then changes directly to online mode.
Adjust Paperway
Online
Menu
Char
1
2
3
4
Setup
The selection made will not be retained after switching off the printer. For more details on
how to set the character density permanently, please refer to the Reference Manual on the On-
line CD-ROM.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical data
Quick start-up
Technical data
➤ Printer
Type
T2265
T2280
specifications
Printing method
Printing width
Serial with 24-needle print head
136 characters at 10 cpi
Print speed
(bidirectional mode, 10 cpi)
650 cps
600 cps
300 cps
200 cps
(bidirectional mode, 10 cpi)
800 cps
700 cps
330 cps
245 cps
HSQ (Matrix 12 x 10)
DPQ (Matrix 12 x 12)
CPQ (Matrix 24 x 12)
NLQ (Matrix 24 x 18)
LQ (Matrix 24 x 36)
100 cps
120 cps
Printing rate
540 pages/h
600 pages/h
9 pages/min (ECMA)
10 pages/min (ECMA)
Character densities
Max. resolution
Emulations
10 cpi, 12 cpi, 15 cpi, 17.1 cpi, 20 cpi
horizontal: 360 dpi; vertical: 360 dpi
Standard: MTPL, Epson LQ2550/LQ2170, IBM XL 24
≤ 55 dB (A) (LQ Mode Sans Serif)
624 x 430 x 276 mm (B x T x H)
19 kg
Noise level
Dimensions
Weight
Power supply
U.S.A./Canada 120 V ± 10%, 60 Hz ± 2%
Europe
230 V ± 10%, 50/60 Hz ± 2%
Power consumption
at 100% throughput 60 VA at 100% throughput 70 VA
when idling: 20 VA when idling: 24 VA
Ambient conditions
Print head
Temperature: 10° to 35°C; Air humidity: 16% to 73%
No. of needles: 24; Needle diameter: 0.25 mm
No. of copies: 1 original + 6 copies
Approvals
ISO 950, CE, GOST, VDE/GS+CB, cULus, FCC/B
For more information on printer specifications as well as interface specifications, refer to the
Reference Manual on the Online CD-ROM.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick start-up
Technical data
➤ Paper
Fanfold paper Tractor1
Continuous single forms
Single set of forms
specifications
Paper weight
No. of copies
60–120 g/m2
1 + 6
(requires individual testing)
Form thickness (max.)
0.60 mm
Single sheet feeder
Single sheets
Paper weight
No. of copies
Form thickness (max.)
80–120 g/m2
1 + 5
0.60 mm
Single set of forms
(requires individual testing)
Sets of forms
Sets of forms can only be processed if the top edge is bound.
ASF-F: Multi-part forms must be loaded with the bound top
edge down. They must be tested individually for their
suitability.
For more information on general paper specifications as well as paper specifications for the
optional tractor units and the automatic sheet feeder, refer to the Reference Manual on the
Online CD-ROM.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
Quick start-up
Accessories
Ribbon cassettes
Order no.
060097
060099
060098
060100
Black ribbon cassette
Ribbon cassette 1 x red, 3 x black
Ribbon cassette with yellow, magenta, cyan, black
Ribbon cassette with red, green, blue, black
For additional accessories, please refer to the Reference Manual on the Online-CD-ROM.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
“All rights reserved. Translations, reprinting or copying by any means of this manual complete or in part or in any different form requires our explicit approval.
We reserve the right to make changes to this manual without notice. All care has been taken to ensure accuracy of information contained in this manual.
However, we cannot accept responsibility for any errors or damages resulting from errors or inaccuracies of information herein.”
TRADEMARK ACKNOWLEDGEMENTS
“CENTRONICS” is a trademark of Centronics Data
Computer Corporation.
“EPSON” and “EPSON ESC/P” are registered
trademarks and “EPSON/P2” is a trademark of
SEIKO EPSON Corporation.
“IBM” is a trademark of International Business
Machines Corporation.
“MS-DOS” is a trademark of Microsoft Corporation.
“Windows”, “Windows 95”, “Windows 98“, “Windows
ME“, “Windows 2000“ and “Windows NT” are
trademarks of Microsoft Corporation.
Download from Www.Somanuals.com. All Manuals Search And Download.
TALLY REPRESENTATIVES
GERMANY
U.S.A.
FRANCE
Tally Computerdrucker GmbH
Postfach 2969
D-89019 Ulm
Tally Corp.
Tally S.A.
P.O.Box 97018
8301 South, 180th Street
Kent, WA 98032
U.S.A.
Phone:+1 425 25155 00
Fax: +1 425 25155 20
19 avenue de L’lle Saint Martin
F-92237 Nanterre Cedex
France
Tél.: +33 1 41 30 11 00
Fax: +33 1 41 30 11 10
Deutschland
Tel.: +49 7308 80 0
Fax: +49 7308 5903
ITALY
AUSTRIA
Tally S.R.L.
Via Borsini 6
UNITED KINGDOM
Tally Limited
Rutherford Road
Basingstoke, Hampshire
RG24 8PD
England, U.K.
Phone: +44 870 872 2888
Fax: +44 870 872 2889
Tally Ges.m.b.H.
Eduard-Kittenberger-Gasse 95 B
A-1232 Wien
I-20094 Corsico (MI)
Italia
Tel.: +39 02 48608 1
Fax: +39 02 48601 141
Austria
Tel.: +43 1 863 40 0
Fax: +43 1 863 40 240
SPAIN
Tally SRL
Russian Federation and C.I.S.
Tally Representative
Park Place Moscow
Office D-206
Leninsky Prospekt 113/1
117198 Moscow
Russian Federation
Phone: +7 095 956 56 40
Fax: +7 095 956 55 41
Aleixandre 8, 2°A
28033 Madrid
España
Phone: +34 91 7219 181
Fax: +34 91 7219 936
CANADA
Tally Corp.
125 Traders Boulevard, 9
Missisauga, Ontario L4Z 2E5
Canada
Phone:+1 905 8904646
Fax: +1 905 8904567
SINGAPORE
Tally AMT Printers Pte. Ltd
63 Hillview Avenue
#08-22, Lam Soon Industrial Building
Singapore 669569
Phone: +65 760 8833
Fax: +65 760 1066
© September 2001 Tally Computerdrucker GmbH
063 050a
Download from Www.Somanuals.com. All Manuals Search And Download.
|