USER GUIDE
TALKSWITCH 24-CA
v3.21
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
1.0 Installing TalkSwitch
1.1 What’s included with TalkSwitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
1.2 Front Panel Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
1.3 Back Panel Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
1.4 Plugging into the Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
1.4.1 Attaching telephone lines to TalkSwitch line jacks . . . . . . . . . . . .4
1.4.2 Attaching phones to TalkSwitch extension jacks . . . . . . . . . . . . . .4
1.4.3 Connecting Devices to the Music and PA Jacks . . . . . . . . . . . . . .5
1.4.4 Connecting TalkSwitch to a PC . . . . . . . . . . . . . . . . . . . . . . . . .6
1.4.4.1 USB connection . . . . . . . . . . . . . . . . . . . . . . . . . . .6
1.4.4.2 Serial connection . . . . . . . . . . . . . . . . . . . . . . . . . .6
2.0 Configuring TalkSwitch
2.1 Installing the TalkSwitch Configuration Software . . . . . . . . . . . . . . . . . . . . . . .7
2.2 Running the TalkSwitch Configuration Software . . . . . . . . . . . . . . . . . . . . . . .8
2.3 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
2.3.1 System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
2.3.1.1 Administration . . . . . . . . . . . . . . . . . . . . . . . . . . .12
2.3.1.2 Telephone Lines . . . . . . . . . . . . . . . . . . . . . . . . . .13
2.3.1.3 Line Hunt Groups . . . . . . . . . . . . . . . . . . . . . . . .15
2.3.1.4 Fax Information . . . . . . . . . . . . . . . . . . . . . . . . . .16
2.3.1.5 Local Extensions . . . . . . . . . . . . . . . . . . . . . . . . . .17
2.3.1.6 Remote Extensions . . . . . . . . . . . . . . . . . . . . . . . .18
2.3.1.7 Extension Ring Groups . . . . . . . . . . . . . . . . . . . . .20
2.3.1.8 On-hold/Ringback . . . . . . . . . . . . . . . . . . . . . . . .22
2.3.2 Voicemail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
2.3.2.1 Local Extension Voicemail . . . . . . . . . . . . . . . . . . .23
2.3.2.2 Remote Extension Voicemail . . . . . . . . . . . . . . . . .25
2.3.2.3 General Voicemail . . . . . . . . . . . . . . . . . . . . . . . .28
2.3.2.4 Global Settings . . . . . . . . . . . . . . . . . . . . . . . . . .31
2.3.3 Call Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
2.3.3.1 Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
2.3.3.2 Auto Attendant . . . . . . . . . . . . . . . . . . . . . . . . . . .34
2.3.3.3 Telephone Lines . . . . . . . . . . . . . . . . . . . . . . . . . .39
2.3.3.4 Local Extensions — Call Cascade . . . . . . . . . . . . .42
2.3.3.5 Remote Extensions — Call Cascade . . . . . . . . . . .44
2.3.3.6 Extension Ring Groups — Call Cascade . . . . . . . .46
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3.4 Call Back/Call Bridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
2.3.4.1 Auto Call Back . . . . . . . . . . . . . . . . . . . . . . . . . .50
2.3.4.2 Prompted Call Back . . . . . . . . . . . . . . . . . . . . . . .53
2.3.4.3 Call Bridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
2.3.5 Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
2.3.5.1 Audio Controls . . . . . . . . . . . . . . . . . . . . . . . . . .57
2.3.5.2 Manual Transfer . . . . . . . . . . . . . . . . . . . . . . . . . .58
2.3.5.3 Miscellaneous . . . . . . . . . . . . . . . . . . . . . . . . . . .59
2.3.5.4 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . .62
3.0 Using TalkSwitch
3.1 In the Office — Receiving calls with or without the Auto Attendant . . . . . . . .67
3.1.1 Receiving calls using the Auto Attendant . . . . . . . . . . . . . . . . . .67
3.1.2 Receiving calls without the Auto Attendant . . . . . . . . . . . . . . . .68
3.2 In the Office — Making and Receiving Calls . . . . . . . . . . . . . . . . . . . . . . . .68
3.2.1 Making calls from a Local Extension . . . . . . . . . . . . . . . . . . . . .68
3.2.2 Receiving calls at a Local Extension . . . . . . . . . . . . . . . . . . . . .68
3.2.3 Placing calls on Hold at a Local Extension . . . . . . . . . . . . . . . .69
3.2.4 Transferring calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
3.2.5 Call Park — Parking and retrieving callers . . . . . . . . . . . . . . . .70
3.2.5.1 Parking a caller . . . . . . . . . . . . . . . . . . . . . . . . . .70
3.2.5.2 Parking a caller using Auto Park . . . . . . . . . . . . . .71
3.2.5.3 Retrieving a parked call . . . . . . . . . . . . . . . . . . . .71
3.2.5.4 Using Call Park with the External Paging option . . .71
3.2.6 Call Queue — Queuing and retrieving callers . . . . . . . . . . . . .71
3.2.6.1 Queuing calls to a single extension . . . . . . . . . . . .71
3.2.6.2 Queuing callers to an Extension Ring Group . . . . .72
3.2.7 Using the TalkSwitch Call Waiting feature . . . . . . . . . . . . . . . . .72
3.2.8 Conference calling with TalkSwitch . . . . . . . . . . . . . . . . . . . . . .73
3.2.9 Using Phones connected in parallel to TalkSwitch . . . . . . . . . . .74
3.2.10 External modem telephone line access . . . . . . . . . . . . . . . . . . .75
3.3 Out of the Office — Receiving Calls through Call Forwarding . . . . . . . . . . .75
3.3.1 The three ways to forward calls . . . . . . . . . . . . . . . . . . . . . . . .75
3.3.2 Transferring calls from a Remote Extension . . . . . . . . . . . . . . . .76
3.3.3 Screening options for forwarded calls . . . . . . . . . . . . . . . . . . . .76
3.4 Using the TalkSwitch Voicemail System . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
3.4.1 Activating Voice mailboxes . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
3.4.2 Retrieving Messages/Accessing a Voice mailbox . . . . . . . . . . . .78
3.4.3 Pager and Cell Phone notification . . . . . . . . . . . . . . . . . . . . . .80
3.5 Music-on-Hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
3.6 Mode Switching Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
3.7 Out of the Office — Making Calls with Call Back and Call Bridge . . . . . . . .82
3.7.1 Using Call Bridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
3.7.2 Using Call Back . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
3.8 Upgrading the TalkSwitch Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Appendix A — Help & Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89
Appendix B — Using TalkSwitch with Telephone Company Calling Services . . . . .97
Appendix C — Quick Commands and DTMF Functions . . . . . . . . . . . . . . . . . .101
Appendix D — Safety Precautions and Regulatory Information . . . . . . . . . . . . .105
Appendix E — TalkSwitch One Year Warranty . . . . . . . . . . . . . . . . . . . . . . . . .109
Appendix F — Return Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113
Appendix G — Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115
Appendix H — TalkSwitch and Power Interruptions . . . . . . . . . . . . . . . . . . . . . .117
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing
TalkSwitch
1
1.1
What’s included with TalkSwitch
The TalkSwitch products come shipped with the following items:
1. The TalkSwitch Unit
2. AC Power Adapter (Warning: never use any other Power Adapter other than
the one provided with the TalkSwitch.)
3. USB cable
4. 6' RJ-11 Telephone Cable – (2)
5. Software CD (This contains the configuration software and documentation)
6. Quick Reference Cards – (Local Extension Use)
7. TalkSwitch Start Guide
8. TalkSwitch Memory Card (optional purchase)
If any of these items are missing, please contact your reseller.
The TalkSwitch Line jacks are sensitive to high voltage spikes from lightning. If you live
in an area where electrical storms occur regularly, we recommend that you protect
TalkSwitch by plugging the telephone cords coming from the TalkSwitch line jacks to a
surge protection device connected to the incoming telephone lines.
When you first receive TalkSwitch and live in an area with cold temperatures, do not
plug TalkSwitch into a power outlet until the system has warmed to room temperature.
Otherwise condensation could build up on the electronics and cause damage when
powered up.
1.0
Download from Www.Somanuals.com. All ManualsISnesatarclhlinAngdTDaolwknSlwoaidtc. h
1
1.2
Front Panel Descriptions
TalkSwitch’s front panel consists of a power button (“Power”) and 5 LED lights that
do more than let you know TalkSwitch is plugged in and turned on.
What do the LED lights tell you?
LED light
Line 1
State
Description
On Solid Line 1 is currently in use.
Pulsing Slowly The Line 1 caller is on hold.
Flickering
Quick Pulse
Line 1 is ringing.
Line 1 is engaged by another device on the line.
Line 2
On Solid Line 2 is currently in use.
Pulsing Slowly The Line 2 caller is on hold.
Flickering
Quick Pulse
Line 2 is ringing.
Line 2 is engaged by another device on the line.
Power / Data
On Solid
Flickering
TalkSwitch is powered on.
The PC connected (via Serial or USB) to
TalkSwitch is either sending or retrieving
information from TalkSwitch.
Pulsing Slowly Global Message Waiting Indicator (optional).
Line 3*
Line 4*
On Solid Line 3 is currently in use.
Pulsing Slowly The Line 3 caller is on hold.
Flickering
Quick Pulse
Line 3 is ringing.
Line 3 is engaged by another device on the line.
On Solid
Line 4 is currently in use.
Pulsing Slowly The Line 4 caller is on hold.
Flickering Line 4 is ringing.
Quick Pulse Line 4 is engaged by another device on the line.
For more details on Line LED Error codes, see Troubleshooting — Appendix A
*
Line 3 and 4 lights apply to TalkSwitch 48 models
2
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
1.3
Back Panel Descriptions
Before connecting all your phones and lines to TalkSwitch, you may want to
proceed with configuring the unit first. (See section 2.1) This will minimize the
disruption time for your telephone lines while setting up the system.
1.3.1 The TalkSwitch 24
Jacks/Ports
MUSIC
What to plug in
Plug in a radio, CD player, PC soundcard or any other
device that emits an audio signal if you wish to use
TalkSwitch's Music-on-Hold feature. This is a 1/8" (3.5
mm) phono jack. Mono cables are recommended.
PA
Connect to a P.A. system if you wish to use the external
paging feature. This is a 1/8" (3.5 mm) phono jack.
Mono cables are recommended.
E1, E2, E3, E4
Plug in any analog device that uses a standard (RJ-11)
telephone jack, such as: telephones, answering
machines, fax machines, internal or external PC
modems. Once these devices are plugged in TalkSwitch
will recognize them as Ext. 111, Ext. 112, Ext. 113, or
Ext. 114. Consider connecting the receptionist’s phone to
Extension 114 as this will allow for calls to be received or
made through Line 1 of TalkSwitch.
L1/L2, L2
USB
This is where you plug in your telephone lines (RJ-11).
If you have 2 lines out of 1 phone jack, you can plug into
the L1/L2 jack. Use a surge protector if you live in an
area prone to lightning strikes.
Use the USB port if your PC supports USB connectivity. If
you use the USB port, you cannot use the serial port
simultaneously.
1.0
Download from Www.Somanuals.com. All ManualsISnesatarclhlinAngdTDaolwknSlwoaidtc. h
3
SERIAL*
You can use a serial cable (RS232) that connects
TalkSwitch to your PC. If you use the serial port you
cannot use the USB port simultaneously. *Serial cables
are not supplied with the TalkSwitch unit.
POWER
Plug the supplied AC Power Adapter in here. Rating:
16VAC 1.1 A output. Do not use any other power adapter
as this may cause damage.
MEMORY SLOT
Memory expansion slot (located on side). Used to
expand internal memory for voicemail and Auto
Attendant messages. TalkSwitch Memory cards can be
purchased from your local TalkSwitch reseller. Simply
place the memory card in the slot and TalkSwitch will
automatically detect and start using the extra memory
within 20 seconds.
The ‘PF’ box in between E4 and L1/L2 represents power failure support. In the event
of a power failure or loss of power to TalkSwitch, Extension 114 will be able to receive
calls and make calls on Line 1.
1.4
Plugging into the Back Panel
1.4.1 Attaching telephone lines to TalkSwitch line jacks
You can connect your telephone lines from the wall jack(s) to the TalkSwitch Line
jacks with the phone cables provided. Take note of which telephone line is connected
to which Line Jack on TalkSwitch - this information will be used in the configuration
section. In order to minimize disruption to your business, you may want to configure
TalkSwitch first before connecting it to your lines and phones.
We recommend that you connect surge protectors between TalkSwitch and your
telephone lines to protect against lightning damage.
1.4.2 Attaching phones to TalkSwitch extension jacks
You can connect any analog device (regular telephone, cordless phone, fax machine,
answering machine, modem) to TalkSwitch's extension jacks. Multiple devices can be
connected to each extension jack by ‘chaining’ them together or using a line splitter.
4
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
To Attach a Single Line Corded or Cordless Telephone, Fax Machine or Answering
Machine:
Connect your single line analog telephone or fax machine to one of TalkSwitch’s
extension jacks E1 to E4 just as you would if you were plugging them into a
standard telephone wall jack.
To Attach a Two-line Telephone:
Option #1 (Use it as one TalkSwitch extension.)
Disregard the telephone’s Line 2 jack (plug-in). Connect the telephone’s Line 1
plug-in to any one of TalkSwitch’s extension jacks. You will still be able to access
both telephone lines in the same manner as if you were using a single line
telephone attached to TalkSwitch.
Option #2 (Use it as two TalkSwitch extensions.)
You could use your two-line telephone as two separate TalkSwitch extensions.
Connect the telephone’s Line 1 and Line 2 plug-ins to two separate extension
jacks.
Most two-line phones have separate plug-ins for two incoming telephone lines (Line 1
and Line 2). If your two-line telephone does not have separate plug-ins, you can use
a “Line 1/Line 2” line splitter to separate the two lines. Download the Quick Guide at
www.talkswitch.com for more detailed examples on connecting multi-line phones.
To Attach an Internal or External Modem:
Simply plug the modem’s telephone cable into one of TalkSwitch’s extension
jacks. Your modem is now a TalkSwitch extension and will be able to access all
lines and take advantage of TalkSwitch’s call routing features.
If you don’t want to change your dial up settings for the modem, you will need
to enable Direct Line Access for the extension associated to the modem. See
section 2.3.1.4 for more details on configuring Direct Line Access.
1.4.3 Connecting Devices to the Music and PA Jacks
The Music jack is designed to support any audio source (CD player, radio, tape player,
sound card etc.) for playing music or messages to callers while on hold. Simply
connect the audio source via its headphone output to the Music jack. The Music jack
requires a 1/8'' (3.5mm) phono connector. If you have more than one TalkSwitch
connected to a LAN, you will need to provide audio to all the Music jacks on each
TalkSwitch.
1.0
Download from Www.Somanuals.com. All ManualsISnesatarclhlinAngdTDaolwknSlwoaidtc. h
5
The PA jack can be connected to a PA System for external paging or to an
amplification system to screen voicemail or to use as a line simulator. The PA jack
requires a 1/8'' (3.5mm) phono connector. If you have more than one TalkSwitch
connected to a LAN, you will need to provide a connection from each TalkSwitch to
the PA system.
1.4.4 Connecting TalkSwitch to a PC
There are two ways to connect TalkSwitch 24CA directly to your PC for configuration
— USB or Serial
USB:
Use the provided USB cable to connect TalkSwitch to an available USB
port on your PC or USB hub.
Serial*: Use a serial cable (RS232) to connect TalkSwitch to an open COM port
on your PC. *Serial cables are not provided with TalkSwitch units.
1.4.4.1 Connecting TalkSwitch to a PC using a USB cable
If you have an available USB port then connect TalkSwitch to the PC using the USB
cable. When you run the TalkSwitch software, you will need to select ‘USB’ as the
connection type then press connect.
1.4.4.2 Connecting TalkSwitch to a PC using a Serial cable
If you have an available Serial port, then connect TalkSwitch to your PC using an
optional Serial cable.
When you run the TalkSwitch software, you will need to select ‘Serial’ as the
connection then select the Serial Port associated to this physical Serial port on your PC.
Make sure you do not have any other communications programs running at the same
time you want to use the TalkSwitch configuration software. These may include Palm
Pilot, Hot Sync, TalkWorks, Digital Camera software. These programs tend to ‘hold’
onto COM ports and not make them available for any other programs.
If you are having problems communicating with TalkSwitch, please check the
Troubleshooting section of the manual.
6
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
Configuring
TalkSwitch
2
2.1
Installing the TalkSwitch Configuration Software
Insert the TalkSwitch CD into your CD drive. The Install program will automatically
launch. If the software does not launch automatically, you can use Windows Explorer
to explore your CD-ROM drive. Double-click the Setup.exe file, then follow the
instructions on the screen. If you are installing on a Windows XP machine, do not
enable Windows 98 compatibility mode for the TalkSwitch software. The TalkSwitch
software can also be downloaded from the TalkSwitch website (www.talkswitch.com).
Configuration software system requirements:
PC running Windows XP/2000
120 MB free hard disk space
128 MB RAM
800 x 600 minimum video resolution
If you are having problems retrieving the settings from TalkSwitch, please check the
Troubleshooting section of the manual.
2.0
Configuring TalkSwitch
7
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2
Running the TalkSwitch software
After installation is complete, double-click the TalkSwitch icon. The following screen
provides different connection options.
Connection Type: USB
If TalkSwitch is connected to the PC via a USB cable, then select this option and
press ‘Connect’ to continue.
Connection Type: Serial
If TalkSwitch is connected to the PC via a Serial cable, then select this option and
choose the Serial Port associated to the connection. Press ‘Connect’ to continue.
Connection Type: Ethernet
Ethernet is not a supported connection type for the TalkSwitch 24CA. Only USB
and Serial are supported.
Connection Type: Internet
Internet is not a supported connection type for the TalkSwitch 24CA since it does
not have an Ethernet port. Only USB and Serial are supported.
Connection Type: File
If you wish to work offline on a configuration file, select this option then press
the Browse button to select the file you wish to view/edit.
Restore Firmware:
This activates the TalkSwitch Firmware Update procedure in the event a firmware
update has failed. Follow the instructions accordingly.
8
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
2.3
Configuration
The configuration screen consists of 4 parts:
1
2
3
4
1. Menu Items
5
2. Configuration Navigation
Controls what is displayed in the configuration window.
3. Configuration Window
Displays configuration information.
4. View System Information
Click this button to view each TalkSwitch unit’s MAC address, IP
address, hardware version and firmware version.
5. Resize
Grabbing this corner by left-clicking on the mouse allows you to
increase or decrease the window size.
There is context sensitive help information available for each option in the
configuration software. Simply rest your mouse cursor over any control for a second
or two and then information related to that control will appear.
2.0
Configuring TalkSwitch
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Items - File
Open File...
Opens existing configuration files from the PC. Default configuration files
are included with the software. TalkSwitch also backs up to a file called
“LastSavedConfig.dat” every time you save settings to TalkSwitch.
Save to TalkSwitch
Saves the current configuration to TalkSwitch.
Save to file...
Saves the current configuration to a file.
Exit
Closes the Configuration.
Retrieve settings:
Retrieves settings from TalkSwitch connected to the PC.
Update Firmware:
This action locks the system down and then proceeds with updating the
firmware once all calls have terminated. For more details on upgrading the
TalkSwitch Firmware, see Section 4.8.
Menu Items — View
Toolbar
Toggles the toolbar on/off.
Status Bar
Toggles the status bar on/off.
Menu Items — Tools
Memory Usage:
Displays a dialog box showing internal memory usage for Voicemail or Auto
Attendant messages.
Voicemail Manager:
Displays a dialog box giving you options to check the status of all voicemail,
delete a mailbox password, and reset mailboxes to factory default.
10
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
Terminal Window:
Displays a command line interface to enter commands. Useful for troubleshooting
in conjunction with technical support.
Defaults:
Select this option to reset the current page or the entire configuration back
to defaults.
Menu Items — Help
Support on the Web:
Launches your browser and directs you to our support site.
About TalkSwitch:
Displays the TalkSwitch software version number, TalkSwitch firmware version
number and Copyright information.
Additional PDF help documents can be located in the Start Menu> TalkSwitch folder.
Configuration Navigation
The Configuration Navigation organizes all the configuration topics within folders.
The following is a brief description of each configuration folder:
About TalkSwitch
This tab displays version information about the TalkSwitch software, firmware
and hardware. It also displays memory usage with details about voicemail
messages and Auto Attendants.
System Information
This folder allows you to configure the system setup. This includes activating
lines, extensions, VoIP and music-on-hold.
Voicemail
This folder allows you to configure each individual voice mailbox and also some
global settings for the voicemail system.
Call Handling
This folder allows you to configure how you want incoming calls to be handled.
It allows you to setup your Auto Attendants and individual call handling for each
line and distinctive ring number for both operating modes.
2.0
Configuring TalkSwitch
11
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3.1 System Information
2.3.1.1 Administration
It is recommended that you enter an Administrator password to prevent tampering
with the system configuration.
System Name:
The system name is for informational purposes to confirm the identity of the
system when connected.
Administrator password:
To activate the use of an administrator password, enter a 4 to 8 digit password.
The password can only contain numbers since it is also used to gain access to the
system using a touch tone phone.
If the administrator forgets their password, the only option to gain access to the
configuration settings is to contact TalkSwitch.
12
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
2.3.1.2 Telephone Lines
This section is used to inform TalkSwitch about the lines or VoIP ports plugged into
its back panel. Simply select a line and fill in the information. For each line there is
a status message (“Line detected at initialization”) indicating if TalkSwitch detected
a line plugged into the associated line port. If a line is plugged into a line port and
is not detected, check your telephone line, and then choose File>Retrieve settings to
update the screen.
Connection type:
Select what’s connected to the Line jack on TalkSwitch. Selecting VoIP means that
you have a VoIP device plugged into the jack. This will now enable callers to select
250-299 from a local extension or auto attendant to speed dial a VoIP location.
In the “Phone numbers” section:
Enter the ‘main’ telephone number for the appropriate line connected to
TalkSwitch. Enable the Distinctive Ring Numbers 1 and/or 2 if you have this
service on the current line and wish to have incoming calls handled 'differently'
on the basis of the distinctive ring. If you want Distinctive Ring numbers handled
the same way as your 'Main' number, do not place a check mark in the box.
Next, enter the ‘Distinctive Ring’ telephone number for each of the Distinctive
Ring numbers associated to this line. Distinctive Ring 1 corresponds to any
double ring pattern. Distinctive Ring 2 corresponds to any triple ring pattern.
2.0
Configuring TalkSwitch
13
Download from Www.Somanuals.com. All Manuals Search And Download.
In the “Telephone company services” section:
Select any of the Telephone Company Services that you currently have for each
line. The following is an explanation of each service and the impact of selecting
each option with respect to how TalkSwitch handles calls. For definitions and
details on how to use these features with TalkSwitch, see Appendix B.
3-Way Calling/Conference:
TalkSwitch can work with either service to forward calls to Remote
Extensions or other external phone numbers while using the same
line (Same Line Connect). You can also use this service as an option
for bridging calls to external numbers when calling into TalkSwitch
from the outside. If you find that you are having difficulties with line
levels when forwarding calls to Remote Extensions or using Call
Bridge, you should use 3-way calling to forward calls as a solution.
Transfer and Clear (Centrex/Plexar transfer):
TalkSwitch can clear the line after forwarding a call to a Remote
Extension if your telephone line supports this feature. If you enable
this feature without actually having the service, callers will be
disconnected after the call is forwarded to the Remote Extension.
Call Waiting:
Check this box if you have Call Waiting service on the current line. It
is recommended that you remove this service from your line(s) since
there is no way for TalkSwitch to handle a second call on the same
line while it is handling the first call. You may want to instead
consider adding the Hunt/Rollover service to your lines.
Caller ID:
Check this box if the current line provides Caller ID information.
TalkSwitch will pass along the Caller ID information to selected
extensions. Also, TalkSwitch can use the time information provided by
Caller ID to update TalkSwitch’s internal clock. (see section 2.3.5.4).
Telephone Company Voicemail:
Check this box if you are subscribed to a Telephone Company
Voicemail service.
Hunt/Rollover/Busy Forwarding:
Check this box if the current line is associated with a Line Hunt or
Line Rollover service from the Telephone Company. In general, any
lines that belong to a Hunt/Rollover group should be configured to
handle calls the same way.
In the “Calibration” section:
After you have configured the lines, it is recommended that you calibrate the
lines. Completing this procedure optimizes your telephone line volume levels for
the Call Bridge and Call Forwarding (with Remote Extensions) features.
14
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
Note: Only lines that are detected can be calibrated.
2.3.1.3 Line Hunt Groups
There are a total of 9 Line Hunt Groups for controlling outbound call line selections.
These Line Hunt Groups are used by the Local and Remote Extensions, and when
using the Call Bridge feature. Each Hunt Group can support several line choices and
will attempt to grab an available line in the order that they are listed (Lines to hunt)
for that Hunt group. These settings have no effect on incoming calls.
The default setup:
Hunt Group 9:
selects any available line
Hunt Group 81: selects Line 1
Hunt Group 82: selects Line 2
First select a Line Hunt Group then name the group(s) if desired.
Under Set Line Hunt Group, select the lines you wish to add to the Hunt Group by
clicking the check boxes left of the line. Repeat this process for the other Hunt
Groups. Lines will be hunted in the order they are listed from top to bottom.
2.0
Configuring TalkSwitch
15
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3.1.4 Fax Information
The information in this tab helps configure TalkSwitch to handle faxes.
If you have a dedicated fax line or a Distinctive Ring number for faxing associated to
a line, please choose this ‘Fax number’ in the list. If you don’t have a line dedicated
for inbound faxing, select ‘none’.
If you do not see your fax number in the list, make sure you have activated the
appropriate line or Distinctive Ring number in the Telephone Lines section under
System Information.
Next, select the extension number where you have your fax device connected. For
example if you have your fax machine connected to E3 on the rear of the TalkSwitch,
then select extension number 113.
By default, when both a dedicated line and fax extension have been selected for the
first time, the software automatically configures the incoming call handling
properties for that line to ring only the fax extension you specified on this page.
16
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
2.3.1.5 Local Extensions
Local Extensions are phones or devices connected to any of the extension jacks at the
back of TalkSwitch. See sections 1.3 and 1.4 for more details on connectivity.
Select any of the extensions that you wish to configure.
Local Extensions are by default activated with the associated Voice mailbox. Voice
mailboxes for each Local Extension can be de-activated in the Voicemail section in
the System Information folder.
Last Name/First Name:
Enter the first and last name of the person associated to the extension. The last
name is required if the person is to be included in the ‘Dial by Name’ directory
listing used at the Auto Attendant level. The person using that extension must
also record their name for the directory. Instructions for recording the name are
listed in the interface. Whatever name is entered will appear on the Caller ID of
another Local Extension during an intercom call.
2.0
Configuring TalkSwitch
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Direct Line Access:
Direct line access allows you to configure the extension to access a specific Hunt
Group automatically for outbound calls when the extension goes off hook. For
example, you may have a fax machine connected to this extension and don’t
want to reprogram the speed dial phone numbers. In this case you would select
‘Direct line access’ and choose the appropriate Hunt Group. As soon as the fax
goes off hook, TalkSwitch will hunt the specified lines for an available line. This
feature is also useful if you want to avoid dialing any digits for accessing a line.
Warning: When using Direct Line Access, telephone company line dialtone is first
available when picking up the handset. The following features are only available from
TalkSwitch internal dialtone: Intercom Calling, Hold Retrieve, Line Hunt Groups,
Voicemail Retrieval/Access, Call Pick Up, P.A. Access, Parked Call Retrieval, Do Not
Disturb functions and entering Command Mode. To obtain internal dialtone from an
extension which has Direct Line Access enabled, dial Flash after going off hook.
Hunt Group Access:
This is used if you want to permit or restrict specific Hunt Group access to the
extension. Click the button and simply organize the appropriate Line Hunt
Groups that are permitted for this extension. (All extensions are defaulted to have
no restrictions.)
2.3.1.6 Remote Extensions
With TalkSwitch’s Remote Extensions, you can have calls forwarded directly from
your home/office to any phone number you choose. Your cell phone, pager or any
out-of-office number becomes a ‘Remote Extension’ of your office system.
You can have calls forwarded directly or screen callers. If you are unavailable or
choose not to accept calls, they can be transferred back to your office (e.g. to
voicemail or another extension) or forwarded to another out-of-office telephone
number (e.g. to a business partner’s cell phone) depending upon the Cascade
configuration.
For details on how to use Remote Extensions, see section 3.3.
TalkSwitch assigns a Remote Extension number to each call forwarding telephone
number. Calls can then be forwarded by the Auto Attendant or transferred by someone
in your office simply by dialing the Remote Extension number. There are 8 Remote
Extensions available per TalkSwitch unit.
18
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
Choose a Remote Extension to configure. After you have activated a Remote
Extension, you must enter a phone number in order for the extension to be
considered active and usable by the system.
Remote phone number:
Enter the phone number of the Remote Extension (note: no specific prefixes are
required - put the number in just as though you were dialing it from a regular
phone). You may use the following in the space provided: digits 0 – 9, space,
comma, dash,
#
and
*.
Last Name/First Name:
Enter the first and last name of the person associated to the extension. The last
name is required if the person is to be included in the ‘Dial by Name’ directory
listing used at the Auto Attendant level. The person using that extension must
also record their name for the directory. Instructions for recording the name are
listed in the interface.
Connect using:
Select the Line Hunt Group that TalkSwitch will use to connect to that Remote
Extension. For example if you have an inexpensive long distance carrier setup for
the lines in Hunt Group 84, you may want to use this Hunt Group for your long
distance Remote Extensions.
2.0
Configuring TalkSwitch
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Use Same Line Connect
Enabling this option allows incoming calls, when forwarded to the Remote
Extension, to use the same line in which the originating call came in. Using this
feature allows only one line to be used when forwarding incoming calls to a
Remote Extension. This feature can only be used when the line that the
originating call came in on has the 3-Way Calling/Conference or Transfer service
(Centrex/Plexar). If the line does not have any of these services, the call will be
forwarded using the Hunt Group chosen in the “Connect using:” section.
If you have a ‘Transfer and clear’ service on your line(s) and want to have
TalkSwitch clear lines after forwarding calls to Remote Extensions, you will need
to enable ‘Centrex/Plexar transfer’ on the Miscellaneous tab under ‘Options’. If
your service requires the remote end to answer the call before the transfer can be
made, then you should use ‘play accept/reject prompt’ or ‘play caller’s name first’
screening option set on the ‘Answered at ext.’ in the Remote Extension section
under Call Handling.
Note: Remote Extensions do not have the ability to manually transfer calls
when using ‘Same Line Connect’.
When using Same Line Connect, callers will hear silence while they are on hold since
the callers are on hold at the Telephone Company and not at TalkSwitch. If you want
callers to hear music while they are on hold for calls forwarded to Remote Extensions,
do not use Same Line Connect. It’s best to experiment with different settings in order
to decide what works best for your configuration.
2.3.1.7 Extension Ring Group
There are a total of 10 Extension Ring Groups available for your use. Ring Groups are
extensions 300 to 309. By default, extension 300 is configured to ring all extensions.
Different uses for Extension Ring Groups:
Example 1: You are the president of a company and you don't want to handle
calls from the general public, yet you want to be alerted when your important
colleagues try to contact you. Your regular Local Extension may be 111 for most
people, but you can also configure a Ring Group such as extension Ring Group
300 to ring your extension with a different ring pattern. You then tell your
colleagues to always choose extension 300 at the Auto Attendant or ask to be
transferred to extension 300 when speaking to someone in the office. Now
without being subscribed to Caller ID, you can tell just by how your phone rings
if you consider the caller to be important or not.
20
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
Example 2: You have a company with several departments . You may want to
configure Extension Ring Group 300 for the Sales Department, in which case it will
ring extensions 111, 112, 113, and 114. You may want to also set up Ring Group
301 for Technical Support, in which case it will ring extensions 115 and 116.
First select an Extension Ring Group (300-309) that you would like to configure and
activate it. If desired, name the extension in the ‘Ring Group name’ space.
Ring pattern:
Choose how you want the phone(s) to ring for the Ring Group.
Set Ring Group:
To configure, select each extension that you wish to add to that Ring Group. Ring
Groups must have at least one extension checked in order to be accessible.
2.0
Configuring TalkSwitch
21
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3.1.8 On-hold/ Ringback
If you wish to have callers listen to music or advertising while they are on hold, you
will need to enable Music-on-hold in this tab.
On-Hold Settings:
If you have a music source connected to the MUSIC jack, then you can select the
‘play music’ option. Otherwise leave the option set to play a ‘double beep’ when
callers are placed on hold.
Transfer Settings:
Select the option that best suits your environment and system configuration.
Note: If you connect a music source to the Music jack and do not enable Music-on-
hold, the caller will hear both music and a beep sound when on hold. Also when the
caller makes a selection at the Auto Attendant to go to an extension that has call
screening enabled, they will hear both ringing and music.
22
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
2.3.2 Voicemail
This section deals with the internal voicemail system included with TalkSwitch. It
allows you to activate Local, Remote and General mailboxes and change global
settings to the voicemail system. For details on how to use voicemail, see section 3.4.
2.3.2.1 Local Extension Voicemail
By default, all Local Extensions are activated with the associated voice mailbox.
Play announcement only
:
If you want to use this mailbox for informational purposes only and prevent callers
from recording messages, then check the 'Play announcement only' box.
If a caller presses ‘0’:
Select what action to take when a caller presses “0” during the different modes while
in a voice mailbox:
go to voice mailbox: Callers will be transferred to the specified mailbox.
go to local extension: Callers will be transferred to the specified local extension.
go to remote extension: Callers will be transferred to the specified remote extension.
go to ring groups:
Callers will be transferred to the specified ring group.
2.0
Configuring TalkSwitch
23
Download from Www.Somanuals.com. All Manuals Search And Download.
play announcements: Callers will be transferred to the specified announcement.
go to auto attendant: Callers will be transferred to the Auto Attendant.
perform no action:
No action will be performed when ‘0’ is pressed.
Load Greeting:
You can load a pre-recorded voicemail greeting from your PC to TalkSwitch.
The file must be an 8khz, 8-bit, mono µ-law .wav file.
Voicemail Notification Settings:
Set the manner in which you want to be notified when new messages arrive.
Remote Phone Notification:
If you want to be notified at another location when new messages arrive, you
can use Remote Phone Notification. Simply enter the phone number of the
cell phone or location where you want to be notified.
Notification Settings:
Detailed instructions are provided for how you may want TalkSwitch to
handle notification calls being considered successful or requiring another
attempt.
Pager Notification:
Use Pager Notification if you want to be notified by pager when new messages
arrive. Simply activate the feature then enter the pager phone number and
the numeric message to be displayed on the pager.
Message Waiting Light:
Click on this option to set a message waiting light to indicate when a message
has been received for an extension. You can select on which local extensions
in your system the light will be activated when a message is received. By
default, the message waiting light will turn on at the extension associated
with a local mailbox.
Configuration Notification Options:
Define how TalkSwitch will dial out of your office when notifying you of a
voicemail. If the first connection is not successful, define how many times, and
at what intervals TalkSwitch will continue to attempt to reconnect.
Under the conditions where you choose to be notified by both pager and remote
phone, TalkSwitch makes sure that both locations have been contacted before
finishing the notification process.
24
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
Dial notification phone number…
These parameters control which Hunt Group is used for both the Remote
Phone and Pager Notification calls. It also allows you to adjust the number
of rings before it will abort the attempt then follow the parameters listed in
the next section.
If attempt unsuccessful…
These parameters control how many times TalkSwitch will try to notify the
Remote Phone or Pager before it will abort the entire notification attempt.
You can also specify the time interval between attempts.
2.3.2.2 Remote Extension Voicemail
2.0
Configuring TalkSwitch
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Extension voicemail is similar in features to the Local Extension voicemail.
Ensure that the remote extension has been enabled, otherwise you will not be able to
activate its voicemail.
Play announcement only:
If you want to use this mailbox for informational purposes only and prevent callers
from recording messages, then check the 'Play announcement only' box.
If caller presses ‘0’:
Select what action to take when a caller presses “0” during the different modes while
in a voice mailbox:
go to voice mailbox: Callers will be transferred to the specified mailbox.
go to local extension: Callers will be transferred to the specified local extension.
go to remote extension: Callers will be transferred to the specified remote extension.
go to ring groups:
play announcements: Callers will be transferred to the specified announcement.
go to auto attendant: Callers will be transferred to the Auto Attendant.
Callers will be transferred to the specified ring group.
perform no action:
No action will be performed when ‘0’ is pressed.
Load Greeting:
You can load a pre-recorded voicemail greeting from your PC to TalkSwitch.
The file must be an 8khz, 8-bit, mono µ-law .wav file.
Voicemail Notification Settings:
Set the manner in which you want to be notified when new messages arrive:
Remote Phone Notification:
If you want to be notified at another location when new messages arrive, you
can use Remote Phone Notification. Simply enter the phone number of the
cell phone or location where you want to be notified.
Notification Settings:
Detailed instructions are provided for how you may want TalkSwitch to handle
notification calls being considered successful or requiring another attempt.
Pager Notification:
Use Pager Notification if you want to be notified by pager when new messages
arrive. Simply activate the feature then enter the pager phone number and
the numeric message to be displayed on the pager. See following page for
screen shot of the pager notification options.
26
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
Message Waiting Light:
Click on this option to set a message waiting light to indicate when a message
has been received for an extension. You can select on which local extensions
in your system the light will be activated when a message is received. This
option can be useful since remote voice mailboxes are not associated with any
local extensions.
Configuration Notification Options:
Define how TalkSwitch will dial out of your office when notifying you of a
voicemail. If the first connection is not successful, define how many times, and
at what intervals TalkSwitch will continue to attempt to reconnect.
Under the conditions where you choose to be notified by both pager and remote
phone, TalkSwitch makes sure that both locations have been contacted before
finishing the notification process.
Dial notification phone number…
These parameters control which Hunt Group is used for both the Remote
Phone and Pager Notification calls. It also allows you to adjust the number
of rings before it will abort the attempt then follow the parameters listed in
the next section.
If attempt unsuccessful…
These parameters control how many times TalkSwitch will try to notify the
Remote Phone or Pager before it will abort the entire notification attempt.
You can also specify the time interval between attempts.
27
2.0
Configuring TalkSwitch
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3.2.3 General Voicemail
General Voicemail is similar in features to both Local and Remote Extension
Voicemail. These are generic mailboxes used for general purposes, such as messages
for a sales team, or technical support group.
Play announcement only:
If you want to use this mailbox for informational purposes only and prevent callers
from recording messages, then check the 'Play announcement only' box.
If a caller presses ‘0’:
Select what action to take when a caller presses “0” during the different modes while
in a voice mailbox:
go to voice mailbox: Callers will be transferred to the specified mailbox.
go to local extension: Callers will be transferred to the specified local extension.
go to remote extension: Callers will be transferred to the specified remote extension.
go to ring groups:
play announcements: Callers will be transferred to the specified announcement.
go to auto attendant: Callers will be transferred to the Auto Attendant.
perform no action: No action will be performed when ‘0’ is pressed.
Callers will be transferred to the specified ring group.
28
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
Load Greeting:
You can load a pre-recorded voicemail greeting from your PC to TalkSwitch.
The file must be an 8khz, 8-bit, mono µ-law .wav file.
Voicemail Notification Settings:
Set the manner in which to be notified when new messages arrive.
Remote Phone Notification:
If you want to be notified at another location when new messages arrive, you
can use Remote Phone Notification. Simply enter the phone number of the
cell phone or location where you want to be notified.
Notification Settings:
Detailed instructions are provided for how you may want TalkSwitch to
handle notification calls being considered successful or requiring another
attempt.
Pager Notification:
Use Pager Notification if you want to be notified by pager when new messages
arrive. Simply activate the feature then enter the pager phone number and
the numeric message to be displayed on the pager. See following page for
screen shot of the pager notification options.
Message Waiting Light:
Click on this option to set a message waiting light to indicate when a message
has been received for an extension. You can select on which local extensions
in your system the light will be activated when a message is received. This
option can be useful since general voice mailboxes are not associated with
any local extensions.
Configuration Notification Options:
Define how TalkSwitch will dial out of your office when notifying you of a
voicemail. If the first connection is not successful, define how many times, and
at what intervals TalkSwitch will continue to attempt to reconnect.
Under the conditions where you choose to be notified by both pager and remote
phone, TalkSwitch makes sure that both locations have been contacted before
finishing the notification process.
2.0
Configuring TalkSwitch
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Dial notification phone number…
These parameters control which Hunt Group is used for both the Remote
Phone and Pager Notification calls. It also allows you to adjust the number
of rings before it will abort the attempt then follow the parameters listed in
the next section.
If attempt unsuccessful…
These parameters control how many times TalkSwitch will try to notify the
Remote Phone or Pager before it will abort the entire notification attempt.
You can also specify the time interval between attempts.
30
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
2.3.2.4 Global Settings
Any changes made to Global Settings will affect all system voice mailboxes.
Global Message Waiting Indicator:
This option can be useful if you only use one or a couple of voice mailboxes.
Anytime a new message is left in any active voice mailbox, the Power/Data
light will pulse very slowly to indicate that there is at least one new message
in one of the mailboxes. Once all new messages have been heard, this light
will return to the default state of being on solid.
Mailbox Settings:
The first option controls the order that messages are played back when
listening to voicemail. The default setting plays messages back starting with
the newest message and working back to the oldest messages. This setting is
convenient since many people store several saved messages and don't want to
skip through these messages every time they want to listen to newer messages.
The second control can be adjusted so that you can have the system page or
call your remote phone for every new message received in voicemail or only
the 1st new message received in voicemail.
2.0
Configuring TalkSwitch
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Automatically remove blank and short messages:
Enable this option if you tend to get several messages where callers hang up
rather than leave messages. The advantage of not clearing the short messages
is that employees can listen to the Caller ID information played at the end of
the message to identify callers*.
*Caller ID service required from your telephone company.
View Mailbox Data:
Details are provided for each voice mailbox and announcement. This tool is
useful for better managing the voicemail resources of the system.
Reset Mailboxes:
Use this feature if for example an
employee has left the company and
all greetings, messages and settings
for a particular mailbox need to be
reset. If you need to simply delete
a password, use the Voicemail
Manager located under ‘Utilities’ in
the menu bar.
32
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
2.3.3 Call Handling
2.3.3.1 Modes
The use of Modes allows you to run different call handling configurations at different
times. For example, you may want calls handled one way during business hours and
another way for non-business hours. Modes can be switched either manually or
automatically with the use of Automatic Mode Switching.
Name the modes if desired. The labels will be displayed elsewhere in the
configuration software whenever modes are used.
To use the Automatic Mode Switching feature, you must first activate it by clicking
‘Use Automatic Mode Switching’. Next, set the start times for each mode. If you want
TalkSwitch to change modes more than twice in one day, you can activate up to two
extra mode changes for that day.
If you do not want to use Automatic Mode Switching, you can still switch modes
manually in the software or through any telephone using touch tone commands.
Enter command mode by dialing
then your password if required. Next, dial any
to confirm.
Changes TalkSwitch to mode 1
Changes TalkSwitch to mode 2
TalkSwitch tells you what mode it currently is using
of the following commands followed by
31
32
30
2.0
Configuring TalkSwitch
33
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3.3.2 Auto Attendant
The purpose of the Auto Attendant is to greet callers and instruct them as to which
number(s) they should press on their telephone keypad to reach a particular
extension, person, message, or department. Callers can also directly dial Local
Extensions (1xx), Remote Extensions (2xx), Extension Ring Groups (300-309),
Voicemail (both leave messages and access messages), access Call Back, access Call
Bridge and enter Command mode for making changes to the system configuration.
*400 series mailboxes can be dialed at the Auto Attendant without having to press
first. This can be useful for providing ‘virtual’ extensions associated to a mailbox for
telecommuters or other part-time staff.
A total of 9 different Auto Attendants can be recorded or loaded with a combined total
time of 30 minutes (shared with voicemail, but can be expanded using TalkSwitch
Memory cards). You do not have to use or record all 9 Auto Attendants.
The Auto Attendants can be recorded from any Local Extension or remotely using
touch tone commands.
34
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
Recording Auto Attendant messages using touch tone commands:
Pick up any Local Extension or dial into TalkSwitch and at the Auto Attendant
enter command mode by pressing . If you have the Administrator password
enabled, you need to enter this password. Next, begin entering the proper
touch tone commands listed on the next page. After entering a command, you
will need to press to confirm the entry before entering another command
or exiting command mode. To exit command mode, press or hang up.
Auto Attendant
Record message
Playback message
Erase message
1
2
3
4
5
6
7
8
9
41
42
43
44
45
46
47
48
49
51
52
53
54
55
56
57
58
59
041
042
043
044
045
046
047
048
049
Example: Recording and playing back Auto Attendant
1. Press to enter command mode, then dial 4 1
.
2. After the tone, record your Auto Attendant message. Press when you
have finished.
3. Press 5 1 to listen to your recording.
Note: If you have the Administrator password enabled, you will need to enter this
password after you hit
the first time to enter command mode.
Recording Auto Attendants from an out-of-office phone:
1. Dial into TalkSwitch and wait for the Auto Attendant message.
2. Once the Auto Attendant is playing, use the same keypad commands as you
would from a TalkSwitch extension (in the ‘Recording Auto Attendants
using touch tone commands:’ section). If you have Password Protection
enabled, you will be prompted for your password.
2.0
Configuring TalkSwitch
35
Download from Www.Somanuals.com. All Manuals Search And Download.
In the “At the Auto Attendant, perform the following actions:” section:
If the caller selects
‘0’:
In general, the ‘0’ option is used to direct callers to a receptionist. You may
want to configure this option to ring a Local Extension. For an after hours
auto attendant, you might want to use this option for forwarding to a Remote
Extension for emergency purposes or simply direct callers to a voice mailbox.
If the caller selects
‘1’, ‘
2’, ‘
3’, ‘
4’ or ‘5’:
If the caller presses ‘
1’, ‘
2’, ‘
3’, ‘
4’ or ‘5’ at the specified Auto Attendant,
TalkSwitch can perform one of several actions. You may wonder how a caller
can press just a single digit like ‘1’ or dial extension ‘111’ at the Auto
Attendant and the system understand what it is supposed to do. TalkSwitch
waits 1.5 seconds for another digit after receiving the first digit. If another
digit is not received, then TalkSwitch will follow the action set for the digit ‘1’.
If a caller selects one of the single digit options, you can configure to direct
the call to one of the following options:
– perform no action: If you don’t want to use a particular option, then set
it to perform no action.
– go to voice mailbox: You can configure any single digit option to send a
caller immediately to voicemail. Select the appropriate mailbox or ‘new’
to create a new mailbox if required.
– go to local extension: If you are a small company, sometimes it is useful
to provide a single digit option to ring an extension as opposed to 3 digits.
– go to remote ext.: If you are a small company, sometimes it is useful to
provide a single digit option to ring an extension as opposed to 3 digits.
– go to ring group: If you are a small company, sometimes it is useful to
provide a single digit option to ring an extension as opposed to 3 digits.
– go to auto attendant: TalkSwitch can direct callers to multiple levels of
auto attendants. For example, you might want to use your main auto
attendant to provide language options such as “press 1 for english, 2 for
spanish.” Then you configure option 1 to go to auto attendant 2 (english
version) and option 2 to go to auto attendant 3 (spanish version).
– queue at ring group: Some might consider this feature to be equivalent
to ACD. It can be useful for businesses that want to direct calls to a group
of employees and keep callers on hold until a member of the ring group is
free to take the call.
– play announcement: Announcements are useful for providing directions,
business hours or other information. You can inform callers that they can
press to return to the previous greeting.
– go to directory:
If you want callers to be able to locate employee extension
numbers by last name, then enable this option for one of the selections.
36
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
If a fax call is detected:
If TalkSwitch detects a fax call (by CNG detection), it has the ability to route
it to a Local or Remote Extension or if you do not want to use fax detection,
you can have TalkSwitch perform no action when detecting a fax call.
After the Auto Attendant has finished playing and no selection has been
made within x seconds:
If no selection is detected at the specified Auto Attendant, TalkSwitch can
route the call to any Local or Remote Extension, Ring Group, Voice
mailbox, Auto Attendant, Announcement, dial by name directory, queue the
caller or simply hang up. This feature is included in case someone does not
have a touch-tone phone or if it is a fax call where the calling fax machine
does not emit a CNG tone. It can also be used to forward calls immediately
after the Auto Attendant answers the call. You will notice that you can speci-
fy the length of time after the Auto Attendant has finished playing before it
performs the ‘no selection’ action.
Fax calls are detected by what's called a CNG tone. If a fax machine sends this tone
while trying to establish a connection to a fax machine connected to TalkSwitch,
TalkSwitch will handle the call accordingly. Not all fax machines emit a CNG tone, and
as a result TalkSwitch will not be able to detect the fax call and route it to the fax
machine. To guarantee the reception of every fax, we recommend the use of a
‘Distinctive Ring Number’ added to one of your lines for fax calls. TalkSwitch can then
handle every fax call consistently.
The digits 6, 7, 8 and 9 are not available as programmable options since they are
used for other system features:
If 6 is dialed:
If you press ‘6’ at the Auto Attendant, you will be able to configure and use
Auto and Prompted Call Back. See section 2.3.4 for more details about con-
figuring Call Back and section 3.7.2 for details on how to use Call Back.
If 7 is dialed:
This digit is used to precede PBX extensions of another Centrex or PBX
system. If TalkSwitch is not connected to another system, then you need not
worry about this setting. If TalkSwitch is connected to a PBX system, then see
section 2.3.5.4 for more details.
If 80 - 88, or 9 is dialed:
If you press ‘80 – 88 or 9’ at the Auto Attendant, you will access Call Bridge
if it has been permitted. See section 2.3.4.3 for more details on configuring
Call Bridge and section 3.7.1 for details on how to use Call Bridge.
2.0
Configuring TalkSwitch
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Utilities for Auto Attendants:
Record Instructions
Selecting this button displays a dialog box showing
the instructions on how to record and playback an
Auto Attendant using a telephone. No adjustments
are required for the recording volume as
TalkSwitch automatically adjusts the recording
volume for optimal recordings. If you find that the
playback of your Auto Attendant messages are too
low, you can adjust the playback volume on the
Audio Controls page located under ‘Options’.
Load Auto Attendant
Selecting this button
displays a dialog box with
instructions on how to load
an Auto Attendant using a
pre-recorded wav file. If
you want to have Auto
Attendants professionally
recorded, make sure you
specify that the files need to
be 8KHz, 8bit, mono, and
saved as a mu-law format
wav file.
Erase Instructions
Selecting this button displays a dialog box showing
the instructions on how to erase an Auto Attendant
using a telephone. It is a good idea to erase any
unused Auto Attendants since they share the same
memory as voicemail.
38
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
View Auto Attendant Memory Usage
Selecting this button displays the amount of
time used by all of the Auto Attendants. This
feature helps you keep track of memory usage
as you may have unused Auto Attendant
messages that can be deleted to free up more
memory.
2.3.3.3 Telephone Lines
This section deals with how TalkSwitch will handle incoming calls based on the
incoming line and ring cadence (distinctive ring numbers).
First select a line to configure then the appropriate mode you want TalkSwitch to use
these settings. If you entered the phone number in the Telephone Lines section under
System Information, then the number will appear on the corresponding button.
2.0
Configuring TalkSwitch
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Ring extensions only (no Auto Attendant is played)
If you don’t want the Auto Attendant to answer calls on this line, then select this
option. By default all the Local Extensions are set to ring immediately during an
inbound call. If you select this option, no Call Cascade actions (such as
voicemail) can be performed. If you require a ‘fall through’ sequence such as
going to a voice mailbox, you can configure this line to have an Auto Attendant
answer after x rings then perform an action configured for that Auto Attendant.
If you call in on any line, TalkSwitch will answer after 15 rings with a generic
Auto Attendant so that you can still access the system to make configuration
changes, change modes, access voicemail, or dial extensions.
Play auto attendant...
If you wish to have the Auto Attendant answer calls to give callers options, select
the appropriate Auto Attendant and number of rings before the Auto Attendant
answers . The caller will always hear one more ring than the number of rings you
select since TalkSwitch uses the first ring to determine the ring type and support
Caller ID information.
Go to voice mailbox...
If you don’t need to provide dialable options for callers and simply need to record
messages (for example after hours), then you can configure TalkSwitch to send
callers straight to a voice mailbox. Select the appropriate mailbox and number
of rings before voicemail is engaged. Select the extension(s) you want to ring
before voicemail is engaged.
The next section controls how the extensions will ring before the Auto Attendant
answers the call.
• If you have chosen the Auto Attendant to answer calls immediately, this
section does not require configuration and will be greyed out.
• If the Auto Attendant is set to answer after 1 or more rings, then you can con-
figure when specific extensions will ring before the Auto Attendant answers.
• If no Auto Attendant is chosen to answer on the specified line, then you can
configure when specific extensions will ring (up to 9 rings).
Extensions to ring on an incoming call...
Select the Local Extensions you would like to ring — including before the Auto
Attendant answers or voicemail is engaged. By default, all activated Local
Extensions will ring. If you require certain extensions to ring in a sequence, i.e.
one extension rings first, then another on the 2nd ring, click the “Adjust
Sequence” button to configure.
40
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
Remember: Callers can only be directed with the aid of an Auto Attendant. Calls will
not follow the Call Cascade settings of any of the Local Extensions programmed to ring
on any incoming call.
Adjust Sequence:
This section controls how the extensions will ring before the Auto Attendant
answers the call.
• If you have chosen the Auto Attendant to answer calls immediately, this
section does not require configuration and will be greyed out.
• If the Auto Attendant is set to answer after 1 or more rings, you can then con-
figure when specific extensions will ring before the Auto Attendant answers.
• If no Auto Attendant is chosen to answer on the specified line, then you can
configure when specific extensions will ring up to 9 rings. Remember that no
calls will go to voicemail unless you first have an Auto Attendant answer.
2.0
Configuring TalkSwitch
41
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3.3.4 Local Extensions — Call Cascade
This section configures the incoming Call Cascade options for the Local Extensions.
The Call Cascade routing options are only engaged if the extension is chosen from
the Auto Attendant or if a call is manually transferred to the extension. Once a call
enters an extension’s Call Cascade sequence, the extension “owns” the call. It will not
follow any other extension’s options even if chosen in the Cascade sequence — what
you see in an extension’s Cascade sequence is exactly what you will get. You can set
up the Call Cascade sequences differently for both scheduling modes (the scheduling
for these modes are set up on the Modes tab).
Even if a call is manually transferred to a Local Extension and that extension is busy,
TalkSwitch will follow the Call Cascade options for that extension.
For Local Extensions, there are 4 different ‘Call Cascade’ situations; Busy at
extension, No answer at extension, Answer at extension(routing when a call is
rejected) and Do not Disturb (when turned on at an extension). For each of these
situations, you can control how and where you want the incoming call to the
extension handled with up to 3 ‘cascade’ destinations available.
1. Busy at extension — routing options when this extension is busy
Cascade options include forwarding calls to a Local Extension, Remote
Extension, Extension Ring Group, built in Voicemail, Announcement, invoke
Call Waiting, Auto Attendant, play busy tone (for example: used if a fax
42
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
machine is at the extension), queue caller, or hang up. For more information
on these features, see chapter 3.0 — Using TalkSwitch.
2. No answer at ext. — routing options when this extension does not
answer after a specified number of rings.
Cascade options include forwarding calls to a Local Extension, Remote
Extension, Extension Ring Group, built in Voicemail, Announcement,
Auto Attendant or keep ringing.
3. Answered at ext. — routing options when this extension ‘rejects’ a
screened call.
Selecting ‘play caller’s name first’ will prompt callers, when they choose this
extension at the Auto Attendant, to record their name. When you answer the
call at the extension, it will announce the caller (by playing their recording),
at which time you can choose to accept the call by pressing or reroute the
call to the Cascade options on this tab by either hanging up or pressing
.
Routing options include forwarding calls to a Local Extension, Remote
Extension, Extension Ring Group, built in Voicemail, Announcement, Auto
Attendant or hang up. In the case where ‘hang up’ is selected, TalkSwitch will
first play the following prompt before hanging up: “I’m sorry, that extension
is unavailable at this time. Please try again later.”
4. Do not Disturb — routing options when this extension has engaged the
‘Do not Disturb’ feature.
The Do not Disturb feature is toggled on or off by dialing 62 from a Local
Extension handset. Cascade options include forwarding calls to a Local
Extension, Remote Extension, Extension Ring Group, built in Voicemail,
Announcement, Auto Attendant or hang up. When Do not Disturb is enabled,
you will hear “Do not disturb on” before the dialtone as a reminder since no
calls will ring through to your extension. You may still dial any digits during
this prompt.
In the Cascade sequence, only choosing an extension (Local, Remote or Ring Group)
will allow you to choose an option in the next line. Any other selection is considered
an end-of-call option. Note as well that the last line in the Cascade sequence only
allows the choice of an 'end-of-call' option. This is done so the chance of a caller being
“looped” within the system is removed.
Adding selections to a Call Cascade that are not yet configured:
If while configuring the Cascade sequence you require a Local Extension, Remote
Extension, Ring Group, Voice mailbox or Announcement that has not been
activated as yet, you can easily add the required selection by choosing ‘new’. If
chosen, a screen will appear (depending upon which type is chosen). Simply fill
in the required information to add the new option to the selectable list.
2.0
Configuring TalkSwitch
43
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3.3.5 Remote Extensions — Call Cascade
This section allows you to configure the incoming Call Cascade options for the
Remote Extensions. The Call Cascade routing options are only engaged if the
extension is chosen from the Auto Attendant or if a call is manually transferred to the
extension. Once a call enters an extension’s Call Cascade sequence, the extension
“owns” the call. It will not follow any other extension’s options even if chosen in the
Call Cascade sequence — what you see in an extension’s Call Cascade sequence is
exactly what you will get. You can set up the Call Cascade sequences for both modes
(the scheduling for these modes are set up in the Modes tab).
For Remote Extensions, there are 3 different ‘Call Cascade’ options. For each of these
options, you can control how and where you want the incoming call to the extension
handled with up to 3 ‘cascade’ destinations available.
1. Busy at extension — routing options when this extension is busy
Cascade options include forwarding calls to a Local Extension, Remote
Extension, Extension Ring Group, built in Voicemail, Announcement,
Auto Attendant, play busy tone or hang up. If voicemail or a phone company
prompt answers calls when your cell phone is busy, you may want to
consider using the ‘Play accept/reject prompt’ option under the Answered at
ext. tab.
44
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
2. No answer at ext. — routing options when this extension does not
answer after a specified number of rings.
Cascade options include forwarding calls to a Local Extension, Remote
Extension, Extension Ring Group, built in Voicemail, Announcement or Auto
Attendant, keep ringing or hang up. If you have cell phone voicemail or a
phone company message that answers after a specified number of rings, and
you want the calls redirected to TalkSwitch voicemail, please ensure you set
the number of rings for this extension to a number less than the cell phone
company voicemail or system prompt.
3. Answered at ext. — routing options when this extension ‘rejects’ a call.
With Remote Extensions you have the choice between two different Call
Screening methods, ‘play accept/reject prompt’ and ‘play caller’s name first’.
‘Stay connected’ is the default setting which means that as soon as the
remote phone number is dialed, the call is connected. Selecting ‘play
accept/reject prompt’ will prompt the Remote Extension when answered by
stating “This is call forward”. Selecting ‘play caller’s name first’ will prompt
callers to announce their name. When you answer the call at the extension,
it will announce the caller (by playing the recorded name). After hearing
either message, the Remote Extension can choose to accept the call by press-
ing or reroute the call to the Call Cascade options on this tab by either
hanging up or pressing . Routing options include forwarding calls to a
Local Extension, Remote Extension, Extension Ring Group, built in
Voicemail, Announcement, Auto Attendant or hang up.
If you select ‘stay connected’ you will notice that the Call Cascade options are
greyed out. TalkSwitch can only control forwarded calls when prompting is
enabled. Also, if you use one of the prompted methods for this Remote
Extension, have Music-on-hold enabled, and are not using 3-way calling to
forward calls to this Remote Extension, the Call Cascade will be seamless to
the caller as they will only hear music throughout the entire process of
trying to locate you.
If a call is forwarded to a Remote Extension from a Call Cascade sequence and has
either ‘play caller’s name first’ or ‘play accept/reject prompt’ enabled, the Remote
Extension will hear “This is Call Cascade...” instead of “This is Call Forward...”. This is
done so that you know when the call is rejected, it will send the caller to the next Call
Cascade option of the extension that forwarded the call and not follow the Remote
Extension’s ‘Answer at ext.’ Call Cascade options.
2.0
Configuring TalkSwitch
45
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3.3.6 Extension Ring Groups — Call Cascade
The following section configures the incoming call routing options for Ring Groups.
The Call Cascade routing options are only engaged if the Ring Group has been
chosen from the Auto Attendant or if a call has been manually transferred to the Ring
Group. Once a call enters a Ring Group’s Call Cascade sequence, the Ring Group
“owns” the call. It will not follow any other extensions options even if chosen in the
Call Cascade sequence — what you see in a Ring Group’s Call Cascade sequence is
exactly what you’ll get.
For Ring Groups, there are 3 different Call Cascade options. For each of these options,
you can control how and where you want the incoming call handled with up to 3
‘cascade’ destinations available. You can set up the Call Cascade sequences for both
Modes (the scheduling for these modes are set up on the Modes tab).
46
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
1. Busy at extension — routing options when all the extensions in the Ring
Group are busy
Cascade options include forwarding calls to a Local Extension, Remote
Extension, Extension Ring Group, built in Voicemail, Announcement,
Auto Attendant, play busy tone, queue caller or hang up.
2. No answer at ext. — routing options when all the extensions in the Ring
Group do not answer after a specified number of rings.
Cascade options include forwarding calls to a Local Extension, Remote
Extension, Extension Ring Group, built in Voicemail, Announcement,
Auto Attendant, keep ringing or hang up.
3. Answer at ext. — routing options when any of the extensions in the Ring
Group ‘rejects’ a screened call.
Selecting ‘play caller’s name first’ will prompt callers (when they choose this
Ring Group at the Auto Attendant) to record their name. When you answer
the call at a Ring Group extension, it will announce the caller (by playing
their recording), at which time you can choose to accept the call by pressing
or reroute the call to the Cascade options on this tab by either hanging up
or pressing . Routing options include forwarding calls to a Local exten-
sion, Remote Extension, Extension Ring Group, built in Voicemail,
Announcement, Auto Attendant or hang up.
2.3.4 Call Back/Call Bridge
Working together, Call Back and Call Bridge act as your personal long distance
operator. Whether you are across town or around the world, you can place calls from
your home/office telephone line(s) accessing your long distance savings plan. Call
Bridge allows you to place calls from your office telephone lines when you are not in
the office.
You can make a direct call to TalkSwitch, activate Call Bridge and enter the telephone
number you want to dial. TalkSwitch dials the number from your home/office
telephone lines and connects the two calls together (the call you made to TalkSwitch
and the call TalkSwitch made from your home/office to the dialed party).
2.0
Configuring TalkSwitch
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Here is how it works:
Step 1: Call your TalkSwitch
telephone number to activate
Call Back, then hang up.
Step 2: TalkSwitch calls you
back within 10 seconds.
You answer and accept
Call Back. Your Auto
Attendant will play or if you
have none recorded, the
TalkSwitch message will
play.
Step 3: You can now access
any TalkSwitch extension,
voice mailbox or use Call
Bridge to make calls
around the globe just as if
you were sitting in your
own office.
There are two ways to activate Call Back:
1. Auto Call Back — Auto Call Back is immediate and eliminates the initial
long distance call charge required to activate Call Back. When using Auto Call
Back, all the Call Back settings must be pre-configured before Call Back
is activated. To use Auto Call Back activation, simply dial your home/office
telephone number, let the call ring twice and then hang up. Call Back is
instantly activated!
48
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
2. Prompted Call Back — Prompted Call Back offers the convenience of
entering or changing your Call Back telephone number and message each
time Call Back is activated. To use Prompted Call Back activation, simply dial
your home/office telephone number. When the Auto Attendant answers your
call, you dial ‘6’ to access the Call Back settings through a series of prompts
which allow you to:
a) Enter the telephone number where you would like TalkSwitch to
call you.
b) Record an ‘Announced’ message if required. Call Back will be
activated right after you initiate Prompted Call Back and hang up.
It is important to remember that a small initial long
distance charge will be incurred at your current location when
activating Prompted Call Back.
By default, Prompted Call Back is not activated in the TalkSwitch configuration. You will
need to activate Prompted Call Back before you can use this feature.
The call back out of the system to the number programmed always uses the same line
that was dialed.
2.0
Configuring TalkSwitch
49
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3.4.1 Auto Call Back
There are 4 Auto Call Back numbers that can be configured. Choose an Auto Call
Back to configure and then activate it.
Number to call back:
Enter the Call Back number. This phone number should be entered exactly as you
would normally have to dial the number from this line (i.e. do not enter a Line
Hunt Group in the dialing string).
Use dialing prefix:
If you usually have to dial the same prefix when using Auto Call Back (for
example a long distance calling card number), you may want to enable ‘Use
dialing prefix with Call Back number’. Enter the dialing prefix including any
required pauses or feature keys such as
or . The corresponding key for
inserting a 2-second pause is the comma. For example, if you want to disable Call
Waiting and want to dial a long distance prefix before dialing the long distance
number you could enter the following:
*70,1010555,, This corresponds to
70 for disabling the
Call Waiting feature, a 2 second pause to wait for the new dialtone,
then 1010555 for the long distance prefix, and a 4 second pause to
wait for the new dialtone before dialing the actual long distance
phone number.
50
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
In essence this saves you the hassle of having to always enter the same prefix
every time you want to set up an Auto Call Back phone number.
Number used to trigger Auto Call Back:
Select the line/phone number when out of the office that you will be dialing to
trigger this Auto Call Back. TalkSwitch will initiate the Call Back using the same
line you initially called. You can make configuration changes to this Auto Call
Back by dialing into this phone number only.
Use Password on Call Back:
This option is designed to give you security and to restrict who can use this
particular Call Back number. Simply fill in a 4 to 8 digit password for the Call
Back. When TalkSwitch calls you back, you will be prompted to input the
password to accept Call Back to access Call Bridge or any TalkSwitch extension.
Use Announced Message:
This option is recommended if the number TalkSwitch will be calling back
corresponds to a hotel or a location where somebody else will be answering the
call. The Announced Message option allows you to record a message that will be
played when the call is initially answered during a Call Back. For example, you
may want to say “Please transfer this call to Bob in room 307”. When the hotel
receptionist gets the Call Back and hears this message, they will know to transfer
the call to your room.
The Announced Message can be recorded using an extension handset or remotely
when you access Call Back from the Auto Attendant. The Record message button
gives the instructions to record the message. They are as follows:
Pick up a telephone handset connected to the TalkSwitch and use the
following keypad commands to record the specific Auto Call Back
Announced Message:
1) Press to enter command mode.
If required, enter the password.
2) Next, enter the appropriate command as listed below.
After each command, press to confirm the entry.
Auto Call Back
Recording
Playback
1
2
3
4
61
62
63
64
71
72
73
74
2.0
Configuring TalkSwitch
51
Download from Www.Somanuals.com. All Manuals Search And Download.
There are 4 Auto Call Back accounts per TalkSwitch. If you need to record an
Announced Message for a particular Auto Call Back account, this needs to be done
on the same TalkSwitch unit as the account.
If you need to configure and/or record an Announced Message from a remote location
and do not have the Auto Attendant set to answer this Call Back line, you can call your
Call Back number and let it ring 15 times. A generic Auto Attendant will answer and
you can configure Call Back by pressing 6.
Allow Call Bridge:
To allow Call Bridge after a Call Back has been accepted, check the Allow Call
Bridge box. You may also restrict the Hunt Group access using Call Bridge from
this Call Back by choosing the Hunt Group Access button. By default, Call
Bridge is enabled when Call Back is activated. You will not be prompted for
another password when you choose a Hunt Group at the Auto Attendant.
When entering a Call Back phone number using a telephone, you can enter special
characters using a special prefix. The default prefix is the
key. To enter a
in a
dialing string you will need to dial , for a 2 second pause dial
0, and for a
. When you have completed the entire dial string you need to dial .
, dial
52
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
2.3.4.2 Prompted Call Back
If you are travelling to a location where you do not yet know the phone number,
you can use Prompted Call Back to save on your long distance charges. For details
on using Call Back, see section 3.7.2.
Number to call back:
This phone number should be entered exactly as you would normally have to dial
the number from this line (do not enter a Line Hunt Group in the dialing string).
TalkSwitch will Call Back out on the same line the call originated.
When you access Prompted Call Back from out of the office, you may change this
number before initiating Prompted Call Back. This is the benefit of Prompted Call Back
— you do not need to preset the number before you leave the office.
2.0
Configuring TalkSwitch
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Use dialing prefix with Call Back number:
If you usually have to dial the same prefix when using Prompted Call Back (for
example a long distance calling card number), you may want to enable ‘Use
dialing prefix with Call Back number’. Enter the dialing prefix including any
required pauses or feature keys such as * or #. The corresponding key for
inserting a 2-second pause is the comma. For example, if you want to disable Call
Waiting and want to dial a long distance prefix before dialing the long distance
number you could enter the following:
*70,1010555,, This corresponds to 70 for disabling the Call Waiting
feature, a 2 second pause to wait for the new dialtone, then 1010555
for the long distance prefix, and a 4 second pause to wait for the new
dialtone before dialing the actual long distance phone number.
In essence this saves you the hassle of having to always enter the same prefix
every time you want to set up a Prompted Call Back phone number.
When entering a Call Back phone number using a telephone, you can enter special
characters using a special prefix. The default prefix is the
key. To enter a
in a
dialing string you will need to dial , for a 2 second pause dial
0, and for a
. When you have completed the entire dial string you need to dial .
, dial
Use password on Call Back:
This option is designed to give you security and to restrict who can use Prompted
Call Back. Simply fill in a 4 to 8 digit password and when TalkSwitch calls you
back, you will be prompted to input the password to accept Call Back to access
Call Bridge or any TalkSwitch extension.
Use Announced message:
As was described in the Auto Call Back section, this option is recommended if the
number TalkSwitch will be calling back corresponds to a hotel or a location
where somebody else will be answering the call. The Announced message option
allows you to record a message that will be played when the call is initially
answered during a Call Back. For example, you may want to say “Please transfer
this call to Bob in room 307”. When the hotel receptionist gets the call and hears
this message, they will know to transfer the call to Bob’s room.
The Announced Message can be recorded using an extension handset or remotely
when you access Call Back from the Auto Attendant. The Record message button
gives the instructions to record the message. They are as follows:
54
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
Pick up a telephone handset connected to the TalkSwitch and use the
following keypad commands to record the Prompted Call Back
Announced Message:
1) Press to enter command mode. If required, enter the password.
2) Next, enter the appropriate command as listed below. After each
command, press to confirm the entry.
To record message: 65
To playback message: 75
Allow Call Bridge:
To allow Call Bridge after a Call Back has been accepted, check the Allow Call
Bridge box. You may also restrict the Hunt Group access using Call Bridge from
this Call Back by choosing the Hunt Group Access button.
The call back number shown will always be the last number TalkSwitch dialed in the
last Prompted Call Back session.
2.0
Configuring TalkSwitch
55
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3.4.3 Call Bridge
Call Bridge is a useful feature for saving money while using Call Back or on it’s
own to avoid inflated long distance rates such as with cell phones.
How to use Call Bridge:
1. Call into TalkSwitch from any out-of-office telephone.
2. At the Auto Attendant message, dial the Hunt Group you know you have the
account password for, (let’s say it’s 9 —- the default) you will then be prompted
for the account password.
3. You dial the password and then the key to access a TalkSwitch telephone line.
4. At this point you can dial a number as though you were sitting in the office.
There are four Call Bridge accounts activated by passwords. Each account can be
configured to allow access to certain Hunt Group(s) when using Call Bridge. To
activate an account, check the ‘Activate Call Bridge’ box and fill in a 4 to 8 digit
password. Next, select ‘Hunt Group Access’ and assign the Hunt Groups you want to
make available for this account.
Call Bridge account passwords are only valid when using Call Bridge by itself, not when
used in conjunction with Call Back.
56
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
2.3.5 Options
2.3.5.1 Audio Controls
This section deals with the adjustment of volume and system gain controls. All the
controls on this page update TalkSwitch in ‘real time’. This allows you to adjust
levels during a conversation without having to first save the configuration to
TalkSwitch.
Line Controls:
If callers complain prompts and conversations sound too loud, then levels can be
decreased to a suitable level. Click on ‘Calibrate Lines’ to calibrate lines whenever
a line is added or changed.
Extension Controls:
If you need to increase the volume of conversations through the system to
extensions, you can adjust the gain for each extension individually.
2.0
Configuring TalkSwitch
57
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3.5.2 Transfer Options
This section deals with actions TalkSwitch makes when calls are transferred
manually.
Transferring a caller to a Local Extension:
When performing this action, in the case of the extension not answering or being
busy, you have the choice of TalkSwitch either ringing back the extension that
transferred the call or performing the “no answer” or “busy” action of the
extension that the call was intended for.
You also have the choice to adjust this setting for both the Remote Extensions and
Extension Ring Groups. Any changes made in this section affect the entire system.
Transferring from a Home phone:
You can transfer a call from a phone connected in parallel to one of the incoming
TalkSwitch lines (Home phone) to a Local or Remote Extension, Extension Ring
Group, an Announcement, or a Voice mailbox. This section allows you to choose
which transfer prefix you would like to use to perform the action. The transfer
prefix ‘wakes up’ TalkSwitch and can be considered the equivalent of the Flash or
Link action at a Local Extension. By default the prefix is
.
58
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
Example: Let’s say you receive a call on a phone in your home that is not an
extension of TalkSwitch and you want to transfer the caller to Remote
Extension 215. You would then dial , wait for the ‘double beep’ then dial
215 and hang up. TalkSwitch will now handle the call. For more details, see
section 3.2.8.
Transfer and clear:
TalkSwitch has the ability to clear lines after a call has been transferred. Ensure
you have this service/feature activated on your line(s).
Remote Transfer:
When calls are transferred to a Remote or VoIP Extension, calls can be transferred
back to another extension or voice mailbox by dialing to place the caller
on hold then enter the extension or mailbox. If this is set to Allow screening of
calls, then you would dial
the transfer, then dial
4 to complete the transfer. If you want to cancel
5. If you have selected ‘Perform a blind transfer’,
then the call will be automatically transferred and the line released once the
extension or mailbox has been entered.
2.3.5.3 Miscellaneous
All of the following options affect TalkSwitch as a system. Adjust them according to
your needs.
2.0
Configuring TalkSwitch
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Caller in queue reminder
When a caller is in queue at an extension already in use, a reminder tone is
played at the extension to let them know they have a caller in their queue. This
option allows you to turn off this function.
Call Back ring return
You can adjust the number of rings during a Call Back session before TalkSwitch
disengages the Call Back (i.e. hangs up). Depending upon the situation you may
want to give yourself more time to pick up and accept the Call Back by increasing
the number of rings.
If being used with another PBX
This feature can only work with PBXs that use “flash-hook” as a transfer method. Please
contact your PBX manufacturer for transfer details.
PBX extension length:
If TalkSwitch is being used as an Auto Attendant with another PBX, you
can set the number of digits the PBX uses for its extensions. This allows
TalkSwitch to know what digits to pass on to the PBX to complete the
transfer.
Setting up TalkSwitch behind an existing PBX:
1. Connect the PBX extension to one of TalkSwitch’s Line jacks. You may do this
with all your TalkSwitch lines (1 PBX extension per line) depending upon
how many Auto Attendant ports you would like on the PBX.
2. Configure your PBX on incoming calls to ring the extensions you have
allocated to the TalkSwitch Lines.
3. Configure TalkSwitch’s Auto Attendants to answer at which ring (answer
immediately is used most commonly).
4. Record your Auto Attendants. The Auto Attendants should indicate that the
digit ‘7’ with the PBX extension should be dialed.
Example: If you have chosen the PBX extension length to be 3 digits (and let's
say John Doe's extension is 111 on the PBX), the Auto Attendant should say “To
speak with John Doe, press 7111…”. Now when 7111 is dialed, TalkSwitch puts
the caller on hold and transfers the caller to extension 111.
Internal clock setting:
TalkSwitch can obtain time information from Caller ID for it’s internal clock. If
you have indicated that you do have Caller ID on any of the lines, this option
defaults to the active position. If it is de-activated, TalkSwitch can obtain it’s time
information from the time and date set in the ‘Mode’ tab under Automatic Mode
Switching. TalkSwitch’s clock information is used for Automatic Mode
Scheduling and for internal Caller ID information when intercom calls are
placed in the office.
60
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
Internal Caller ID options:
TalkSwitch has the ability to generate name and number Caller ID to each
extension during intercom calls. If your Caller ID unit/telephone does not support
the name option, you can choose to have TalkSwitch send the number only.
Prompt function key options:
Some phone cards and phone services use different keypad digits for some of their
features. Four options are given to allow flexibility with other systems. If required,
choose an option that best suits working with your phone card or phone service.
You can use these prefixes for entering phone numbers when calling into
TalkSwitch and using Call Back and Call Bridge using 3-way calling.
The following describes how to input special prefixes depending upon which
key is used.
When using the key:
When using the key:
=
=
0 = 2 second pause
1 = Wait for dial tone
0 = 2 second pause
1 = Wait for dial tone
=
=
Example: You want to change the Prompted Call Back phone number remotely
and the special prefix key is the key. After you dial into TalkSwitch and press
‘6’ for Call Back, you go into the options for Prompted Call Back and select to
change the phone number. When prompted to enter the phone number, you
enter:
70 018005551212
This tells TalkSwitch that you want it to dial:
70 (2 second pause) 1-800-555-1212
Audio output options:
The following controls can be used for various reasons including demonstrating
TalkSwitch and screening callers using Voicemail. By default the system is set to
play only PA announcements through the PA output when 0 is dialed at a
Local Extension.
If you are a single person operation and would like to screen all voicemail
messages being left on TalkSwitch, you can connect a speaker to the PA output and
select ‘Play Voicemail prompts and recordings through PA’. When a caller goes to
voicemail, you will hear your greeting and the caller leaving a message. If you
wish to interrupt and speak to the caller, dial 9 from any Local Extension.
2.0
Configuring TalkSwitch
61
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3.5.4 Troubleshooting
The following controls should not be changed unless you are familiar with the effect
they will have on TalkSwitch’s operation. If your system does not appear to be
functioning properly, please contact your reseller for assistance.
Flash Lengths
Accepted Flash Length:
These options control the allowable Flash length from a Local Extension that
TalkSwitch will consider to be an intentional Flash. The range can be adjust-
ed to accept anything from 50ms to 1 second. The default range for accept-
ing a Flash signal at a Local Extension is between 200 ms and 800 ms. Most
phones emit a 500 ms Flash signal when the ‘Flash’ or ‘Link’ button is
pressed.
Transmitted Flash Length:
This option controls the transmitted Flash length from TalkSwitch to the
Telephone Company lines. TalkSwitch emits a Flash when forwarding or
bridging calls using the 3-Way Calling/Conference or Centrex Transfer serv-
ice, or when transferring calls through an existing PBX system. The value can
be adjusted from 50 ms to 900 ms. The default setting is 400 ms. If you notice
that you are having problems with any of the TalkSwitch features that use
3-way calling, you may want to experiment with this value.
62
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
Double Flash time:
When two flashes are detected, TalkSwitch needs to calculate the time between the
flashes to establish if they were intended to propagate a flash at the CO or if it was
the intention to place a caller on hold then quickly retrieve them. The Double
Flash time values signify the maximum time between two flashes that TalkSwitch
will recognize as an intended flash to the CO. When two flashes are detected with
a time gap larger than the value displayed, no flash will be propagated at the CO.
The value can be adjusted from 200ms to 2000ms with the default set at 1200ms.
3-Way Calling wait time:
This option adjusts the time required between flash hook and a dial string. Some
telephone company 3-Way Calling/Conference services require different time
allowances after the flash signal to re-establish dial tone. The default time is 2
seconds so that TalkSwitch can let the lines settle after going off hook before
sending the DTMF digits.
Non-detection of disconnect-clear:
This option controls the length of time when TalkSwitch will "drop" a line when
silence is heard. This safeguard is very useful when a telephone line does not send
out the disconnect-clear signal that tells TalkSwitch the call is finished.
Auto Attendant Adjustments:
Since TalkSwitch allows callers to dial 100, 200, 300 series extensions and 400
series mailboxes, and also allows fall through options for the single digits 1, 2
and 3 at the Auto Attendant, there needs to be a time limit placed on how much
longer after the first digit is pressed that TalkSwitch will wait for another digit
before following the single digit option configured for that particular Auto
Attendant. There are 3 ways to make use of this control. You should be careful not
to isolate your callers from having both choices as listed in (1).
1) With the current setting, callers can dial any Local Extension (1xx), Remote
Extension (2xx), or Ring Group (3xx) as long as the second digit is pressed
within 1.5 seconds of pressing the first digit. Callers can also press just 1, 2, or 3
for options and when TalkSwitch detects no second digit within 1.5 seconds, it will
follow the programmed option for that Auto Attendant.
2) If you don’t want to use the options 1, 2, and 3 for any of the Auto Attendants,
you can set the option to ‘4 seconds’. This pretty much guarantees that callers
will have more than enough time to dial all 3 digits of any extension without
accidentally falling through to one of the Auto Attendant options.
3) If you don’t want to give callers the ability to dial any of the extensions and
only permit them to access single digit options, set this value to ‘immediately’. As
soon as TalkSwitch detects the first digit, it will follow the specified option for that
Auto Attendant.
1.0
Configuring TalkSwitch
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting — Advanced
DTMF Detection:
If callers are complaining of being misdirected when they select options at the
Auto Attendant, then these values might need to be adjusted.
Minimum time: The default setting of 45ms should be adequate for most
environments. It may however be necessary to lower this value if TalkSwitch
appears to have trouble ‘hearing’ digits when dialed at the auto attendant. It
might need to be increased in cases where the system is ‘hearing’ ghost DTMFs
and accidentally misdirecting callers.
Maximum time: The default setting of 65ms should be adequate for most
environments. In most cases this value only needs to be bumped up a bit to help
the system deal with echoed digits seen from cell phones. For example: calls keep
being misdirected to extension 111. This usually indicates that even though the
caller may have dialed 113, TalkSwitch sees 1113 because the ‘1’ was echoed by
the cell phone network. Once TalkSwitch captures 3 digits, it will ignore the rest,
hence the digits ‘111’ will be accepted and the ‘3’ ignored.
64
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
Line CPC/ Disconnect Clear:
If calls are being disconnected accidentally in mid conversation, this usually
indicates a problem with the telephone line. TalkSwitch is always looking for a
‘hangup’ signal from the phone company called a CPC or Disconnect Clear
signal. If the line has ‘shorts’ or even the line card at the central office is defective,
then CPC signals in the 250ms range might come down the line and cause
TalkSwitch to hangup. Try bumping up this value if this seems to be occurring.
Ringback Control:
If an extension seems to ring back as if a caller was on hold, but when answered,
no one is there, this could indicate a debounce problem with the phone
hookswitch. When someone at the extension hangs up, the handset bounces
slightly to cause a flash signal to be seen by TalkSwitch before the hang up. As a
result TalkSwitch puts the line on hold. To help with this problem, this value can
be increased to the point where it will stop the ringbacks.
Line Impedance:
This setting should not be adjusted unless you understand the impact. Line
impedance is set to match as best as possible the line interface from the telephone
company. A good match ensures good levels and low echo.
Fax Detection:
If fax calls are not being directed properly to the fax machine, then you may need
to set this option to detect 1 tone. If it’s set to detect 1 tone and people complain
they have been accidentally routed to the fax machine, then set this value to
detect 2 tones.
2.0
Configuring TalkSwitch
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using
TalkSwitch
3
3.1
In the Office — Receiving Calls with or without the
Auto Attendant
3.1.1 Receiving calls using the Auto Attendant
If you don’t have a receptionist, then using the Auto Attendant will help you handle
all your inbound calls and help improve your corporate image. Once it has been
configured and its messages have been recorded, that's it! The Auto Attendant takes
care of the rest. It will follow whatever instructions (configuration) it was given. For
details on configuring the Auto Attendants, see section 2.3.2.2. For details on
configuring TalkSwitch to answer calls using Auto Attendants, see section 2.3.2.3.
When calls are answered by an Auto Attendant, callers can dial any Local Extension
(1xx), Remote Extension (2xx), Extension Ring Group (300 – 309), choose options
0, 1, 2, 3, 4, 5 if configured to perform specific actions, dial voicemail direct (
+
mailbox), send faxes, or remain on the line to follow an action programmed for that
Auto Attendant. TalkSwitch owners and employees can also access other options at
the Auto Attendant including Call Back (dial 6), Call Bridge (dial 80 – 88, 9),
retrieve voicemail (dial
+ mailbox), enter command mode to make system
changes (dial ). All of these features can be password protected to eliminate system
tampering from outside users.
If you subscribe to Caller ID service, you may want to set the Auto Attendant to answer
after at least 1 ring to give TalkSwitch a chance to capture the Caller ID information.
All calls ring at least one more time than what’s listed for the configuration in the
Telephone Lines section under Call Handling. TalkSwitch ‘absorbs’ this first ring to
determine the ring pattern of the inbound calls so that this same ring pattern can be
duplicated to the Local Extensions.
3.0
Using TalkSwitch
67
Download from Www.Somanuals.com. All Manuals Search And Download.
3.1.2 Receiving calls without the Auto Attendant
If you choose not to use the Auto Attendant to answer calls, please note that the Call
In order for calls to go
Cascade options for the Local Extensions will not be engaged.
to an extension’s mailbox, the Auto Attendant must first answer the call or someone
in the office answer then transfer the call. For details on configuring TalkSwitch to
ring specific extensions during inbound calls, see section 2.3.2.3. Once calls have
been answered at a Local Extension, they can be transferred to any extension or voice
mailbox. See section 3.2 for more details.
3.2
In the Office — Making and Receiving Calls
3.2.1 Making calls from a Local Extension
Placing Intercom calls from one Local Extension to another Local Extension,
Remote Extension or Extension Ring Group:
You can place intercom calls from one Local Extension to another Local
Extension, Remote Extension, VoIP Extension or Extension Ring Group by
simply picking up the extension's handset and dialing the number of the
extension with which you wish to intercom. An Intercom call can be identified by
a unique ring cadence (2 short rings) except in the case of a Remote Extension
Intercom call where the phone will ring as usual or if a Ring Group has selected
a different ring cadence other than ‘normal’. Intercom calls do not follow Call
Cascade sequences of the extensions. Call Cascade is only followed after the call
has been transferred.
Placing ‘out-of-office’ calls from a Local Extension:
To place a call to an out-of-office telephone number from a Local Extension you
must first access an available line by choosing a Hunt Group (9, 81 – 88) at the
internal dial tone. Restrictions to specific Line Hunt Groups can be configured per
extension. Your extension can also be configured to Directly Access a specific line
(i.e. when a handset is picked up, you will hear the Telephone Company dial tone
(not TalkSwitch’s) and can dial an outside telephone number as usual).
If you have Direct Line Access enabled for a Local Extension, you will need to dial
‘Flash’ before dialing any extensions, accessing voicemail or other system features.
3.2.2 Receiving calls at a Local Extension
To receive calls at a Local Extension, simply pick up the extension's handset when
the extension rings. If the call went through the Auto Attendant to the extension and
it has call screening enabled (configured on the Local extension and Ring Group
pages), you have the choice of accepting the call by pressing or, re-routing the call
to it’s ‘Answer at ext.’ Call Cascade options by pressing or hanging up.
68
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
Call Pick Up/Call Grab:
To intercept a call that is ringing on any other Local Extension before or after the
Auto Attendant has engaged, pick up your handset and at the TalkSwitch internal
dial tone, dial 9. This will route the call to your Local Extension.
To “Grab” a call ringing specifically at another extension before or after the Auto
Attendant has answered, dial 7 + the extension number (ie. 7112 to grab a
call ringing at extension 112). If you are in the middle of a call and want to
connect to another caller calling in, press ‘flash’ to place the first caller on hold,
then dial 9 or 7 + <ext.> to connect to the second caller. Once you are
finished the second call or you would like to return to the first caller, press
‘flash’ ‘7’.
3.2.3 Placing calls on Hold at a Local Extension
To Place calls on hold:
To place callers on hold, press ‘flash’. Follow the same procedure to take callers
off immediate hold. If you have multiple callers on hold or in queue at your
extension, you can press ‘flash’ ‘7’ to retrieve callers on a first in/first out basis.
If you use the ‘Hold’ button on a regular phone, you will not be able to access any of
the TalkSwitch features while the caller is on hold. Also, if you have Music-on-hold
enabled, the caller will not hear music while they are on hold.
3.2.4 Transferring calls
From a Local Extension to another Local Extension, Remote Extension or
Extension Ring Group:
To initiate an Unscreened Transfer — Put the caller on hold (by dialing ‘flash’),
dial the appropriate extension number and hang up. The caller will be taken off
hold when the receiving extension is answered. If the transferred call is not
answered after the number of rings specified in the No Answer setting for the
destination extension or, if the extension is busy, either of the following will
happen:
D
efault:
The transferred call will be handled according to the
destination extension's No Answer or, Busy at extension
settings.
Option:
The call will be transferred back to the transferring
extension.
The option is chosen in the Manual Transfer tab in the Options folder.
3.0
Using TalkSwitch
69
Download from Www.Somanuals.com. All Manuals Search And Download.
To announce calls before transferring (Screened Transfer) — Put the caller on hold
and dial the appropriate extension number. If the person at the receiving extension
answers and wishes to take the call, simply hang up or dial ‘flash’ ‘4’ to complete the
transfer and get internal dialtone. The caller will immediately be taken off hold and
connected with the receiving extension. If the person at the receiving extension does
not wish to take the call, you can press ‘flash’ ‘5’ to return to the caller.
Keep in mind that if you dial an extension and it is busy or not answered, you can
still complete the transfer so that the caller will be directed according to that
extensions’ Call Cascade settings.
If you tend to handle many calls, you may want to complete or cancel a transfer without
hanging up. Flash ‘4’ will complete the transfer and then provide internal dialtone
while flash ‘5’ will cancel the transfer and connect you back to the caller.
From a Local Extension to any outside telephone number:
To initiate an Unscreened Transfer — Put the caller on hold, select a Line Hunt
Group (dial 80 for Same Line Connect), then dial the outside telephone number
then press ‘flash’ ‘4’ to complete the transfer. You cannot simply hang up to
complete the transfer otherwise the calls will be disconnected.
If the person at the receiving extension does not wish to take the call, you can
press ‘flash’ ‘5’ to return to the caller.
If you have the 3-Way Calling/Conference or Centrex Transfer feature enabled on the
current line, you can select the Same Line Connect (80) to make use of these features.
Everything proceeds as outlined above other than the fact that you are using the same
line to transfer the call.
3.2.5 Call Park — Parking and retrieving callers
Call Park is a useful feature for placing a caller on hold and then being able to
retrieve them from any other Local Extension. TalkSwitch has 10 Park Orbits for
all models.
3.2.5.1 Parking a caller
To place a caller in a Park Orbit, press ‘flash’ then and choose a Park Orbit (500
to 509). You will hear a confirmation after parking the caller that indicates the caller
has been parked successfully. If the Park Orbit is already occupied, you will hear “I’m
sorry, that extension is unavailable at this time.” then dialtone. Once again press
and choose a new Park Orbit.
70
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
3.2.5.2 Parking a caller using Auto Park
To place a caller in the next available Park Orbit, press ‘flash’ then 510. You will
hear a confirmation that indicates the caller has been parked successfully and into
which Park Orbit.
3.2.5.3 Retrieving a parked call
Once the caller is parked, you can retrieve the caller at another Local Extension by
pressing and the appropriate Park Orbit. If Direct Line Access is enabled at
the extension, then you must press ‘flash’ first.
3.2.5.4 Using Call Park with the External Paging option
If you have the External Paging option enabled on TalkSwitch, you may choose to
announce over the P.A. system (by pressing 0) that there is a call parked in a
specific Park Orbit for a co-worker. For example: “Bob, please pick up 501.” —
which tells Bob that he can retrieve the parked call from any extension by getting dial
tone and pressing 501. The caller will now be connected to Bob at that
extension. If you have Direct Line Access enabled at your extension, you will need
to press ‘flash’ first before retrieving the parked call.
3.2.6 Call Queue/ACD — Queuing and retrieving callers
3.2.6.1 Queuing calls to a single extension
Call Queue is a useful feature for placing multiple callers on hold at your extension
while you are on an existing call. Call Queue is enabled in the Call Cascade section
in the Call Handling folder for Local Extensions and Extension Ring Groups. Callers
will get queued at your extension if you set the first level in the ‘Busy at extension’
Call Cascade to ‘queue caller’.
If an extension is chosen at the Auto Attendant or the caller is transferred from
another extension and the extension is currently busy and has ‘queue caller’ set for
the ‘Busy at extension’ Call Cascade, the caller will hear one of the following prompts
then music (if enabled) while they are on hold:
If the call came from the Auto Attendant and the extension has a voice mailbox:
“The extension you have reached is currently busy. If you wish to continue
holding, please remain on the line. To leave a voicemail message, press 1,
and to return to the main menu, press
”
3.0
Using TalkSwitch
71
Download from Www.Somanuals.com. All Manuals Search And Download.
no
If the call came from the Auto Attendant and the extension has voice mailbox:
“The extension you have reached is currently busy. If you wish to continue
holding, please remain on the line and to return to the main menu, press .”
If the call was transferred from another extension, there is no Auto Attendant
on this line and the extension has a voice mailbox:
“The extension you have reached is currently busy. If you wish to continue
holding, please remain on the line. To leave a voicemail message, press 1.”
If the call was transferred from another extension,there is no Auto Attendant
on this line and the extension has no voice mailbox:
“The extension you have reached is currently busy. If you wish to continue
holding, please remain on the line.”
While the caller is on hold at your extension you will hear a ‘Call Waiting’ beep in
your ear every 60 seconds. If you want to rotate through queued callers, dial ‘flash’
then ‘7’. The caller you are speaking to will be placed on hold, and the first caller in
the queue will be retrieved. If you have multiple callers queued up, pressing ‘flash’
then ‘7’ will retrieve callers on a first in/first out basis.
3.2.6.2 Queuing callers to an Extension Ring Group
If you want to queue callers for a Ring Group, you can configure this action
using an Auto Attendant. This feature is sometimes referred to as Automatic Call
Distribution.
Example: Configure Auto Attendant 1 so that if callers press ‘5’ they will be
queued to ring group 301 for technical support. Now when a caller presses ‘5’ for
tech support, they will immediately enter the queue. Every 60 seconds the caller
will hear the following prompt: “Your call is important to us, please remain on
the line. To return to the previous menu, press star.” Extensions that are part of
the ring group and are available will start ringing within 5 seconds of hanging
up the phone from a previous call. The 5 second delay gives you time to make a
new call or activate ‘Do not Disturb’ as a log out option. After your extension
rings 5 times, it will ring once every 16 seconds and when picked up, you have
the option to take the call or make a new call.
3.2.7 Using the TalkSwitch Call Waiting feature
The Call Waiting feature can be activated as a ‘busy’ option for the Call Cascade
routing for any local extension. When activated, and the extension dialed is in use,
the caller will hear ringing or music depending on the music-on-hold settings. The
person at the extension will hear the following:
1. If the phone supports Call Waiting Caller ID (Type II signaling), then you
will hear a beep followed by a short blip then depending on your phone,
you may hear something similar to a modem noise. This is normal. During
72
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
this notification, the Caller ID information will be displayed on the phone.
The caller will not hear the beep as the phone mutes the other side.
2. If the phone does not support Call Waiting Caller ID, then you will hear a
beep. When the Call Waiting notification beep is heard, the person at the
extension can dial ‘flash’ ‘7’ to put the current caller on hold, then grab the
new caller. They also have the option to terminate the current call and connect
to the new caller by dialing ‘flash’ ‘7’. If the person at the extension does not
want to take the new call, they can simply ignore the Call Waiting beeps and
then TalkSwitch will direct the caller to the next level of the Call Cascade for
that extension (for example send the caller to the associated voice mailbox).
3.2.8 Conference calling with TalkSwitch
2 TalkSwitch Local Extensions and 1 outside caller:
You do not require access to the telephone company's 3-Way
Calling/Conference service to use TalkSwitch's conference calling capabilities.
1. Establish a call with an outside party.
2. Place the outside caller on hold by pressing ‘flash’ and dial the number of
the Local Extension you wish to conference with.
3. When the extension is picked up, you can establish the 3-way call at
anytime by pressing ‘flash’ then ‘6’.
2 outside callers and 1 Local Extension (eg: Line 1 and Line 2):
You can do this type of conference call using two different methods.
The first method is similar to above, using only TalkSwitch for the conference
function.
1. Establish a call with an outside party.
2. Place the outside caller on hold and dial the number of the other outside
party you wish to conference with. If you have ‘Direct Line Access’ enabled
at your extension, you will first need to dial ‘9’ or another Hunt Group
before dialing the second phone number.
3. When the call is answered, you can establish the 3-way call at anytime by
pressing ‘flash’ ‘6’.
When using the telephone company's 3-Way Calling/Conference service you
can conference by following the instructions below:
1. Establish a call with an outside party.
2. Place the outside caller on hold by pressing ‘flash’ twice and then dial the
number of the other outside party you wish to conference with.
3. When the call is answered, you can establish the 3-way call at anytime by
pressing ‘flash’ twice.
3.0
Using TalkSwitch
73
Download from Www.Somanuals.com. All Manuals Search And Download.
If you are experiencing problems with pressing the flash key twice in a rapid
succession (ie. pressing the flash key twice within 1.5 seconds), then you can
make changes in the software that will make it easier to accomplish this task.
See section 2.3.5.5 for details on setting the Double Flash Time.
3.2.9 Using Phones connected in parallel to TalkSwitch
Phones connected in parallel (not connected to TalkSwitch but connected to the
same line) with TalkSwitch will always ring at least once before TalkSwitch starts
ringing its extensions or the Auto Attendant answers the call. This occurs because
TalkSwitch uses the first ring to identify the incoming ring pattern before passing it
on to the extensions or the Auto Attendant (e.g. TalkSwitch determines if the call is a
Distinctive Ring and detects any Caller ID information). A parallel phone can ‘barge
in’ on any telephone call on any of TalkSwitch’s Lines.
Making and receiving calls on phones connected in parallel with TalkSwitch:
Making Calls: Make calls on parallel connected phones just as you would if
TalkSwitch were not sharing the telephone line with them.
Answering Calls: If a call is answered on a parallel connected phone before the
Auto Attendant engages, simply continue with the call as per usual, TalkSwitch
will take no further action. If a call is answered on a parallel connected phone
after the Auto Attendant engages, you can turn off the recorded Auto Attendant
message by using the phone’s touchtone keypad to dial ‘
continue the call on the parallel connected phone.
0’. You may then
Transferring calls on parallel connected phones:
Calls answered on a parallel connected phone can be transferred to any
TalkSwitch extension or voice mailbox. If you want to transfer the caller, simply
key in the ‘Transfer Prefix ’, after you hear 2 ‘beeps’ enter the extension or
voice mailbox number then hang up. You cannot announce a caller to the
transferred extension, but if you do stay on the line, you will be in a ‘conference
call’ state. You can hang up at any time.
If you transfer a call from a parallel connected phone and then hang up, the
extension will ring the number of times selected for that extension. If the
extension is not answered within the specified number of rings, the call will be
handled according to that extension’s Call Cascade actions.
When a phone in parallel with TalkSwitch is off-hook, you will notice that the
corresponding line light will flicker to indicate the line is occupied. TalkSwitch
will not allow extensions to barge in on a call when that line is in use.
74
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
3.2.10 Modems and telephone line access
If your modem is attached to TalkSwitch as an extension, you can configure it to
access your telephone lines in one of two ways:
1. Direct Line Access: You can give the extension to which your modem is
attached ‘Direct Access’ to one of your telephone lines (i.e. you don’t have to
dial 9, or any other Hunt Group to access an outside line). This can be a use-
ful option if you don’t want to change your dial-up options for the modem.
See section 2.3.1.4 for more details on configuring Direct Line Access.
2. Hunt Groups: If you have decided to use a telephone and modem on the
same extension, Direct Line Access may not be the best solution. TalkSwitch
extensions with Direct Line Access immediately connect to one of your lines
when you pick up the telephone’s handset. Therefore, you are unable to select
a specific telephone line or access voicemail, intercom or access other system
features without first pressing ‘flash’.
To have your modem access a specific line using a Hunt Group:
Change your modem's ‘Dial Properties’ to include the intended Hunt Group
(81–88 or 9) followed by the letter ‘w’, before the ‘Dial up Networking’ telephone
number (e.g. 9w555-5555). Including the letter ‘w’ after your ‘Dial out Access’
number instructs your modem to a) dial the access number 81-88 or 9, b) wait
until it detects a dialtone, and then c) dial your ‘Dial up Networking’ number.
If your modem is having problems dialing out, you may have to use a comma ‘,’
which represents a 2 second pause, instead of the ‘w’ for ‘wait for dialtone’.
If you use Direct Line Access, you do not need to put the Hunt Group in the dialing string.
3.3
Out of the Office — Receiving Calls through Call Forwarding
3.3.1 The three ways to forward calls
1. Automatic call forwarding — The Auto Attendant can automatically forward
office calls to your call forwarding telephone number(s) (Remote Extensions).
This is done by using the Auto Attendant message to prompt callers to select
your Remote Extension number(s). (e.g. “To speak to John Doe, press 211.”)
2. Manual call forwarding — If someone in your office has answered a call at a
Local Extension, the call can be ‘transferred’ to one of the call forwarding
(Remote Extension) numbers. Simply put the call on hold at the Local
Extension, dial the Remote Extension number (e.g. 211) to which you want
the call forwarded and then hang-up. The call will be handled according to
the Call Cascade options of that Remote Extension.
3.0
Using TalkSwitch
75
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Conditional call forwarding — If the Auto Attendant answers a call and the
caller selects an extension or Ring Group number that is already busy or is
not answered, the Auto Attendant can forward the call to a Remote (out of
office) extension number. Conditional call forwarding is configured using the
Call Cascade’s ‘No answer’ or ‘Busy at extension’ settings configurable for
each Local Extension, Remote Extension and Ring Group.
3.3.2 Transferring calls from a Remote Extension
Remote Extension Call Transfer is a new feature introduced in version 2.39 of the
TalkSwitch firmware. Calls forwarded to a Remote Extension (not using Centrex or
3-Way Calling services) can be transferred to any local or remote extension, ring
group or voice mailbox. This feature also applies to VoIP Extensions 250-299.
Transferring calls:
Calls can be placed on hold at a Remote Extension by dialing
during a conversation. You will then hear dialtone as you would hear at a Local
Extension. At that time, you can perform any of the following actions:
anytime
1) Press again to retrieve the call placed on hold.
2) Dial any Local Extension, Remote Extension or Ring Group.
3) Dial + mailbox to transfer a caller to a voice mailbox.
If the system is configured in the Troubleshooting2 tab to perform blind transfers
only, then the system will then play the prompt “Call Transferred. Goodbye.” and
hangup after the extension or mailbox is dialed.
If the system is configured in the Troubleshooting2 tab to allow screening of calls,
then you need to dial **4 to complete a transfer or **5 to cancel the transfer and
return to the caller.
3.3.3 Screening options for forwarded calls
The screening options for Call Forwarding are configured using the Call Cascade’s
‘Answer at ext.’ options available in the ‘Remote Extension’ tab, see section 2.3.3.5
Forwarding calls with screening:
When ‘play accept/reject prompt’ is configured in the ‘Answer at ext.’ Call Cascade
option, TalkSwitch plays a pre-recorded prompt to the caller asking them to hold,
and then dials your call forwarding telephone number. When you answer the
forwarded call, TalkSwitch plays a pre-recorded prompt to you that identifies the
call as having been forwarded from your home/office (“This is Call Forward”). You
then have the choice of accepting the forwarded call by pressing
on your
telephone keypad or, re-routing the call to it’s call screening Call Cascade options
by pressing or hanging up.
76
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
When ‘play caller’s name first’ is configured in the ‘Answer at ext.’ Call Cascade
option, TalkSwitch plays a pre-recorded prompt to the caller asking them to
record their name at the sound of the tone. TalkSwitch then asks the caller to
hold and dials your call forwarding telephone number. When you answer the
forwarded call, TalkSwitch plays a pre-recorded prompt identifying the call as
having been forwarded from your home/office (“This is Call Forward, you have
a call from...”) and then plays the recording of the callers name. You have the
choice of accepting the forwarded call by pressing on your telephone keypad
or, re-routing the call to it’s call screening Call Cascade options by pressing or
hanging up.
When either screening option is used, and you have music on hold enabled and you
are not using the 3-way calling feature (Same Line Connect) to forward calls, then
the caller will hear music while TalkSwitch is waiting for the Remote Extension to
accept the call.
If a forwarded call is not answered or the line is busy, TalkSwitch will perform the
following based upon how the call was originally forwarded:
If the call was automatically forwarded: the call will follow the Remote
Extension’s ‘No answer at ext.’ or ‘Busy at extension’ Call Cascade action.
If the call was manually forwarded: The call will follow the Remote Extension’s
‘No answer at ext.’ or ‘Busy at extension’ Call Cascade action. This action can be
changed to ring the extension back who performed the transfer in the
Options>Manual Transfer tab.
If the call was conditionally forwarded: The call will follow the following Call
Cascade action in the ‘No answer at ext.’ or 'Busy at extension' for the original
extension chosen.
3.4
Using the TalkSwitch Voicemail System
Your TalkSwitch system comes with 30 minutes of voicemail recording capacity
shared with Auto Attendant greetings. This capacity can be increased with the
addition of TalkSwitch memory cards. You can add another 1/2, 1, 2 or 4.5 more
hours of storage. Contact your reseller to purchase memory cards. When a TalkSwitch
memory card is inserted in the memory slot, the system will automatically configure
the card within 20 seconds to make it fully functional.
3.0
Using TalkSwitch
77
Download from Www.Somanuals.com. All Manuals Search And Download.
3.4.1 Activating Voice mailboxes
A Voice mailbox is activated from the TalkSwitch configuration software. There are 3 series
of Voice mailboxes that can be activated in the Voicemail section of the configuration:
Local Extension mailboxes:
These mailboxes are generally associated to the Local Extensions. By default,
all Local Extensions are activated with their respective mailbox.
Remote Extension mailboxes:
The Remote mailboxes are associated with the Remote Extensions. If you
activate a Remote Extension and want a voice mailbox associated with that
extension, you can activate that mailbox in the Voicemail tab.
General mailboxes:
These mailboxes are activated in the Voicemail tab. They are not associated
to any particular extension.
If you want inbound calls to go straight to a voice mailbox after x number of rings, then
you need to program an Auto Attendant to answer first, then provide a fall through to
voicemail. See section 2.3.3.3 for an example of this configuration.
Callers can reach voicemail or announcements via the Auto Attendant, Call Cascade,
or transferred from a Local Extension. If an employee wants to leave a message in a
particular mailbox, they can pick up a Local Extension and dial + <mailbox
number>. To transfer a caller to voicemail, press ‘flash’ then
number>.
+ <mailbox
When a caller presses after leaving a message or 2 minutes has elapsed (timeout
period), TalkSwitch will play a prompt asking the caller if they wish to keep the
message, listen to the message or record a new message.
3.4.2 Retrieving Messages/Accessing a Voice mailbox
When a new message is left at a Local Extension mailbox, TalkSwitch will play
stutter dial tone to that extension when the handset is picked up. It can also light up
the message waiting light on a phone if it supports FSK Message Waiting Indicator.
To access a mailbox to retrieve messages or change mailbox options, dial
from a Local Extension or
the Auto Attendant if dialing from an outside location. Employees can also transfer
other employees to access voicemail by pressing ‘flash’ then dialing
+<mailbox number> from a Local Extension or at
+
<mailbox number>. If you have Direct Line Access enabled, be sure to press
‘flash’ before accessing your mailbox.
78
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
If you have a line configured to go straight to voicemail, then you can dial ‘8’ during
the greeting to access messages.
The first time you access your voicemail, you will be prompted to setup your mailbox
by optionally assigning a password, recording a greeting and recording your name
for the dial by name directory. Since there are no directory listings for the general
mailboxes, you will not be prompted to record a name for the directory. Keep in mind
that you should always use the mailbox associated to the same extension since the
directory is related to the extension and voice mailbox.
Once your mailbox has been setup and you access your mailbox, through prompt
instructions you may do the following:
Listen to messages (press 1):
If there are any messages in your mailbox, you will be able to access them by
pressing 1. TalkSwitch will always start with new messages before playing
back any older messages. You have the ability to perform the following
actions while listening to a message and after listening to the message:
Dial 1:
Dial 11:
Dial 3:
Dial 33:
Dial 5:
Dial 6:
Dial 7:
Dial 9:
Rewind 10 seconds
Rewind to beginning of message
Skip ahead 10 seconds
Skip to end of message
Listen to time and date stamp
Forward the message
Delete message
Save message
Dial
Dial
Back up one level
:
:
Skip to next message — New messages left as new.
Change greeting options (press 2):
This section allows you to record a new personal voicemail greeting. The
default greeting is “The extension you have reached is unavailable at this
time. Please leave a message after the tone”.
Keep in mind while recording your greeting or announcement that callers can press
to return to the previous Auto Attendant (if the call came from the Auto Attendant) while
listening to your greeting and can press
when they are done recording for more
options. You may want to give your callers these options for their convenience.
3.0
Using TalkSwitch
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Change personal options (press 3):
This section allows you to change your current password, turn auto date and
time stamp + phone number on or off and setup or change Pager and
Remote Phone Notification for new messages. By default, auto date and time
stamp is on and this information is played at the end of each message. If you
have Caller ID service, then the phone number is also included with the time
and date.
Record name for Dial by Name Directory (press 4):
If you have not already recorded your name for the directory or wish to
change the recording, you can do so here. The dial by name directory is
accessed at the Auto Attendant according to your configuration. Callers are
directed to enter the first 3 letters of the employee’s last name. The system will
find the exact or closest match then play the recorded name + the extension
number, then give them the option to connect to that extension.
3.4.3 Pager and Cell Phone notification
When a new message is left in a voice mailbox, it can notify a pager, cell phone or
any remote number if the mailbox has been configured to do so. Each mailbox can
be configured to notify you for every new message or for only the first new message
received since the last time new messages were accessed.
If using Remote Phone Notification, you have the option to accept or reject the
and to put off
notification call once you answer. To listen to messages, press
listening to messages, press
.
For details on configuring Pager and Remote Phone Notification, please see
section 2.3.2.
3.5
Music-on-Hold
TalkSwitch can play music to callers when they are on hold, parked or queued. The
music played to the callers will be provided by whatever source you have connected
to the MUSIC jack.
If you ENABLE Music-on-Hold and have an audio device plugged into the
back of TalkSwitch:
1. When callers are put on hold at an extension, callers will hear your music
instead of TalkSwitch’s default on-hold beeping tone.
80
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
2. When the Auto Attendant answers a call and transfers the caller to an
extension; the caller will hear a pre-recorded message saying “One moment
please”, and then hear your music.
Music-on-Hold and Call Forwarding to Remote Extensions:
If you are using the telephone company’s 3-Way Calling/Conference service
(Same Line Connect) to activate TalkSwitch’s Call Forwarding, callers will not
hear your ‘music’ when being forwarded to a Remote Extension. When calls are
forwarded, the caller is put on hold by the telephone company central office
switch rather than at TalkSwitch. Therefore, the caller hears silence while being
transferred.
A system prompt will indicate that callers will hear silence while the system tries
to locate their party. This prompt helps explain to callers why all of a sudden they
may hear silence for an extended period of time before possibly connecting to the
Remote Extension. This prompt cannot be disabled.
3.6
Mode Switching Options
Manual Mode Switching:
You can use Telephone Keypad Commands at either a Local Extension or at the
Auto Attendant to have TalkSwitch switch Modes.
At Local Extension dialtone or at the Auto Attendant, dial to enter command
mode, then enter a password if necessary. Next, dial any of the following Quick
Commands followed by the sign:
Activate Mode 1:
Activate Mode 2:
3 1
3 2
Check Current Mode: 3 0
Automatic Mode Switching using the Time Scheduler:
Use the Configuration software or Telephone Keypad Commands to activate
TalkSwitch’s Time Scheduler feature. You can configure TalkSwitch to
automatically switch between Modes by configuring the times for Mode changes
in the ‘Modes’ tab located under Call Handling in the configuration software.
If at anytime you switch modes manually, TalkSwitch will automatically switch
to the proper mode during the next scheduled mode change.
3.0
Using TalkSwitch
81
Download from Www.Somanuals.com. All Manuals Search And Download.
3.7
Out of the Office — Making Calls with Call Back and
Call Bridge
Working together, Call Back and Call Bridge act as your personal long distance
operator. Whether you are across town or around the world, these two features allow
you to place calls from your home/office telephone line(s).
3.7.1 Using Call Bridge
Call Bridge allows you to place calls using your office telephone lines when you are
not in the office. You can make a direct call to TalkSwitch, access a telephone line
connected to TalkSwitch and enter the number you want to dial. This is especially
useful when you are out of the office with your cell phone and need to dial a long
distance number. To avoid the inflated long distance cell rates all you need to do is
make the local call to TalkSwitch to access Call Bridge, then make the long distance
call — accessing your office savings plan.
How to use Call Bridge:
Dial into one of TalkSwitch's Lines (Main or Distinctive Ring). When the Auto
Attendant answers, select a Hunt Group (81-88 or 9) or Same Line Connect (80).
You will then be asked to supply your Account password to receive dial tone. If you
are using Same Line Connect 80, and the line you are on supports the 3-Way
Calling/Conference service, you will be prompted to enter the phone number.
When you have completed your call or if the telephone number dialed was busy,
you can do one of the following:
A) Make another call: Press . TalkSwitch will disconnect you from the call
in progress and you can dial another number or redial the same number.
B) Activate the Auto Attendant: Press
. TalkSwitch will end the Call Bridge
session and activate the Auto Attendant. Once the Auto Attendant message
begins playing, you have the following options:
• Dial (and enter a password if applicable) to enter
Command Mode.
• Dial '6' to change/enter Call Back settings.
• Dial one of your extension numbers (Local, Remote or Ring
Group). This option allows you to use Call Back to contact
someone in your office, check your voicemail, etc.
C) End the Call Bridge Session: Simply Hang up. This will end your Call
Bridge session and disconnect you from TalkSwitch. If you want to
guarantee that TalkSwitch disconnects at the end of a Call Bridge session,
dial
, then hang up.
82
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
If you changed the ‘Special Prefix’ to
make another call, and dial
mode, you will still need to enter
instead of
, you will need to dial
to
to return to the Auto Attendant. To enter command
.
The Call Bridge telephone number dialed can be any telephone number: local,
long distance, toll free (800 and 888) or international. Simply enter the telephone
number as you would if you were sitting in your office. For long distance calls, do not
forget to include the ‘1’, country code, and area code if applicable.
3.7.2 Using Call Back
The Call Back feature allows you to initiate TalkSwitch to call you at a specified
telephone number. This gives you access to any of the following:
• Call Bridge
• Local Extensions, Remote Extensions and Extension Ring Groups
• Voicemail
• Configuration settings
Using Call Back involves ‘3’ easy steps:
1. You call your TalkSwitch telephone number to activate Call Back.
2. You answer and accept the Call Back. (TalkSwitch calls you back within
30 seconds.)
3. At the Auto Attendant you can: choose to perform Call Bridge, dial any
extension, access and retrieve voicemail or configure TalkSwitch.
Activating Call Back:
There are two ways to activate Call Back, Prompted and Auto activation:
1. Using ‘Prompted Call Back’ Activation: From your out-of-office location,
dial a TalkSwitch telephone number (
‘
Main
’
line ring until the Auto Attendant answers your call and then dial
or
‘
Distinctive Ring
’
‘
). Let the
on the
6’
telephone keypad. If you have enabled password protection you will be asked
to supply your password and TalkSwitch will then offer a series of prompts.
Now you can either enter 1 and hang up to initiate the Call Back or, if you
need to enter a new Prompted Call Back number, enter 2 to access the
Prompted Call Back settings then follow the prompts.
For Prompted Call Back, TalkSwitch always dials the last Prompted Call Back number
entered. If you do not have the Auto Attendant set to answer a line, a generic TalkSwitch
Auto Attendant will answer after 15 rings and you can then dial 6 to access the Call
Back settings.
3.0
Using TalkSwitch
83
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Using ‘Auto Call Back’ Activation: From your out-of-office location, dial one
of the Call Back telephone numbers that has been pre-configured for Auto
Call Back activation. Let the line ring at least once, but no more than three
times and then hang-up (before the call is answered). Within 20 seconds,
TalkSwitch will dial your Auto Call Back number.
It is important to remember that all the Call Back settings must be pre-configured
before using Auto Call Back. Please be sure that the Auto Attendant for the line using
Call Back does not answer before 4 rings.
Accepting the Call Back:
There are two ways to accept a Call Back from TalkSwitch.
1. Call Back is normally accepted by answering the call and pressing , then
if required, entering your password. This option is used when you have a
direct line to your Call Back telephone number.
2. The ‘Use Announced message’ option allows the Call Back from TalkSwitch
to reach you even when you are staying at a hotel or are in an office where
calls are intercepted by a receptionist or switchboard operator. When the Call
Back is answered, TalkSwitch will begin playing your pre-recorded
message (e.g. “Please forward this call to Jane Doe in room 312”). The
message will be played repeatedly for ‘2’ minutes. When the call is
forwarded to you, press , then enter your password on the telephone
keypad to accept the Call Back. (If the Call Back is not accepted within the
initial ‘2’ minute period, TalkSwitch will disconnect the Call Back.) After you
accept the call, you will hear the Auto Attendant, and you can now make your
selection to check your voicemail, ring an extension, use Call Bridge, or enter
command mode.
3.8
Upgrading the TalkSwitch Software and Firmware
We are continually looking for ways to enhance your communications capabilities.
When new features are added, we want TalkSwitch users to have immediate access to
the update.
TalkSwitch supports firmware updates for adding new features. Because of this
ability, you can easily update your TalkSwitch by visiting our website at:
www.talkswitch.com/support
84
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
Step #1 — Check current version
To identify the appropriate update file, you must first determine your TalkSwitch
firmware and software versions. You can find your TalkSwitch version numbers by
selecting ‘About’ from the Help menu in the configuration software.
Write down the software and firmware version numbers and then go to the TalkSwitch
website at www.talkswitch.com/support. You will find instructions there to help you to
select and download the appropriate upgrade. Follow the instructions on the site, as
they will take precedence over any instructions in this manual.
Step #2 — Download new software and firmware
When you select and click on the appropriate version for download, a screen will
appear asking you what you would like to name the file you are about to download,
and in which folder/directory you would like to save it. We suggest leaving the file
name as is (eg. install.exe) and saving it on your Desktop. Once the download is
complete, you can begin your upgrade by double clicking on the install file or using
the ‘Run’ option on your Windows ‘Start’ menu. A series of windows will guide you
through the installation process.
This process updates your configuration software to a newer version. You still need to
update the firmware to take advantage of new features. The new firmware file will
have been placed in the TalkSwitch directory after running the install program.
Step #3 — Updating the firmware
The final step in the upgrade process is to update the firmware. Follow the
instructions listed on the website carefully for performing the update.
3.0
Using TalkSwitch
85
Download from Www.Somanuals.com. All Manuals Search And Download.
The actual update process will take approximately 1 to 5 minutes, depending on how
many files are needed for the update. During the update, the LED lights on
TalkSwitch’s front panel will show diagnostic indicators for the update.
In the event the firmware update was unsuccessful, please follow the instructions
through the update process again. If you continue to have problems, please contact
your reseller or TalkSwitch.
Firmware updates will not alter your system configuration. In the event of a major
system update, it may be necessary for the configuration file to be reset to default
values. In this case you will need to reconfigure the entire system. In the case of a major
system update, TalkSwitch will mention any issues involved with the firmware update.
If you replaced your computer with a new one, please use the software that matches
the latest version of firmware running on TalkSwitch. If obtained from our website,
you can once again download the install file. All install files found on the website
have both the entire software program and the latest firmware.
86
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
Appendices
Appendix A — Help & Troubleshooting
Appendix B — Using TalkSwitch with Telephone
Company Calling Services
Appendix C — Quick Commands and
DTMF Functions
Appendix D — Safety Precautions and
Regulatory Information
Appendix E — TalkSwitch One Year Warranty
Appendix F — Return Policy
Appendix G — Specifications
Appendix H — TalkSwitch and Power Interruptions
Appendices
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A — Help & Troubleshooting
If you are having problems with the configuration or operation of TalkSwitch, please
check the Troubleshooting section starting on this page. If you don’t find the solution
to your problem, next try checking the FAQ section located under the Support area at
our website: www.talkswitch.com/support. There is a vast amount of information
available on the website.
If you cannot resolve your problem and require further assistance, you can do one of
the following:
1. Contact your TalkSwitch reseller.
2. Contact our Customer Support department by e-mail:
3. Ask for a ‘Technical Support Specialist’. If you would like to speak with
a Technical Support Specialist, call TalkSwitch at 1-866-393-9960 or
(613) 725-2466 weekdays between 9:00 a.m. and 5:00 p.m. EST.
Please have the following information available when you call:
a) Your e-mail address and telephone number.
b) The serial number located on the bottom of TalkSwitch and your date
of purchase.
c) The number of telephone lines that you have connected to TalkSwitch.
d) The telephone company services that you are using with TalkSwitch.
e) Your PC’s operating system (e.g.Windows 95, 98, ME, 2000, XP)
Troubleshooting
This section of the manual is designed to help you quickly resolve problems that
can be experienced by new TalkSwitch users. The problems and their corresponding
solutions are organized in the following manner.
1. Problems that can occur when installing the Configuration software.
2. Problems that can occur during Configuration.
3. Problems that can occur while using TalkSwitch's features.
Before examining the ‘Problems’, review these common installation checks first!
Appendices
89
Download from Www.Somanuals.com. All Manuals Search And Download.
The first things you should check
1. Check that your telephone cables are connected to a wall jack at one end and
TalkSwitch at the other. Ensure the devices you are using as TalkSwitch exten-
sions (phones, faxes, etc.) are plugged into the extension jacks located on the
back panel of TalkSwitch. (Do not plug your extensions directly into a wall
jack unless that jack is wired to a TalkSwitch extension jack.)
2. Check the Serial or USB connection between TalkSwitch and your PC.
3. Ensure that TalkSwitch’s power adapter is plugged into a working power
outlet and that TalkSwitch is turned on. Please make sure that you are using
the power adapter that was provided with TalkSwitch. This is a unique
adapter and it cannot be substituted with any other adapter. If your adapter
appears to be defective, please contact your reseller to order the proper
replacement adapter.
Diagnostic codes for the lights flasing on the front panel of TalkSwitch
Line 1,2,3,4 lights flashing simultaneously: The Unit ID of this TalkSwitch is in
conflict with another TalkSwitch unit on the same LAN. Make sure you assign a
different Unit ID to each TalkSwitch unit.
Line 2 and 3 lights flashing simultaneously: There is a file system error. To fix
the problem, reboot TalkSwitch. It will do a file system check and fix any problems
encountered. If this does not resolve the problem, contact your reseller.
Line 1 and 4 lights flashing simultaneously: There is a voice mailbox error. To fix
the problem, reboot TalkSwitch. It will do a file system check and fix any problems
encountered.
Line 3 and 4 lights flashing simultaneously: Firmware not loaded or corrupted
error. To fix the problem, reload the TalkSwitch firmware. Make sure you update
with the last version you updated with. Do not use an old version off the install
CD if you have updated your system at least once.
Line 1 and 4 then Line 2 and 3 lights flashing alternately: System prompts not
loaded or corrupted error. To fix the problem, reload the TalkSwitch firmware.
Make sure you update with the last version you updated with. Do not use an old
version off the install CD if you have updated your system at least once.
90
TalkSwitch User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Problems that may occur during Configuration
Problem: I am not able to “Retrieve settings” from my TalkSwitch.
• Make sure your TalkSwitch is turned on and plugged into a working power
outlet. Then select “Retrieve settings”, available under the File menu in the
Configuration Software.
• From the Control Center, choose ‘PC Connection’ and then select COM Port.
Ensure that the Configuration Software is using the correct port to commu-
nicate with TalkSwitch. Then select "Retrieve settings", available under the
File menu in the Configuration Software.
• Try ‘resetting’ TalkSwitch (turn the power off and then back on). Then select
“Retrieve settings”, available under the File menu in the Configuration
Software. This will often correct any ‘miscommunication’ that may have
occurred between TalkSwitch and your PC.
• Make sure you do not have any other communications programs running at
the same time you want to use the TalkSwitch configuration software. These
may include Palm Pilot, Hot Sync, TalkWorks, Digital Camera software.
These programs tend to ‘hold’ onto COM ports and not make them available
for any other programs.
Problem: I am unable to configure TalkSwitch using a touchtone phone and the
Keypad Commands.
• TalkSwitch cannot be configured using a phone connected in parallel to
TalkSwitch.
• If you are trying to configure TalkSwitch using an Out-of-Office phone, you
must first enter Command Mode. If you have enabled password protection,
you must also first enter the correct password.
• If you are trying to configure TalkSwitch using a Local Extension, make sure
the extension has not been given 'Direct Access' to your telephone lines. If so,
you will have to dial ‘Flash’ to receive internal dialtone.
• If the TalkSwitch configuration software is open, you cannot configure
TalkSwitch using DTMF. If the software is closed and you continue to get the
prompt “I’m sorry, TalkSwitch is currently being configured.” Try resetting
TalkSwitch. It is possible that the software did not close properly and as a
result TalkSwitch still thinks it is in ‘configuration mode’.
Appendices
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Problems that may occur while using TalkSwitch’s features
The Auto Attendant:
Problem: The Auto Attendant does not play when calls come in.
• Make sure you have recorded the Auto Attendant message.
• Check your Call Handling settings for the ‘Auto Attendant answers’ number
of rings. It may be that the number of rings after which the Auto Attendant is
set to answer calls is set too high.
• Check what mode TalkSwitch is currently running. It is possible that you are
in Mode 2 and have not configured TalkSwitch properly for this mode. Check
what you have programmed for Mode 2 in the Telephone Lines section under
‘Call Handling’.
• The line is not connected properly to TalkSwitch. Check to see that the line
light associated to the line ringing in is flickering. If not try replacing the
phone cord.
Problem: The Auto Attendant message is broken up or very faint.
• Adjust the line volume control in the Audio Controls page. Ensure the actual
recording is comparable to the prompts already on the system.
• The quality of the microphone in the telephone handset that you are using to
record your Auto Attendant also affects the quality of your recording. Try
recording the Auto Attendant using another extension/telephone.
Problem: The Auto Attendant answers calls before any of the extensions ring.
This is a problem for those TalkSwitch users who wish to have their Local
Extensions ring before the Auto Attendant picks up incoming calls.
• Check the ‘Extensions to ring’ column in the Telephone Lines tab in the ‘Call
Handling’ folder. It may be that the number of rings after which the Auto
Attendant is set to answer calls is set too low.
Problem: The Auto Attendant is transferring calls to the wrong extension.
• Verify which extension jacks your devices (phones, faxes) are attached to.
Problem: The Auto Attendant answers calls, but does not transfer them to the
extensions.
• Make sure your extensions are plugged into the extension jacks on the back
panel of TalkSwitch (instead of your telephone wall jacks).
• Check your settings in the Auto Attendant page. Are all the options pointing
to the correct extensions or other options?
92
TalkSwitch User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Music-on-Hold:
Problem: Callers hear music and 'ringing' when the Auto Attendant transfers their
call to an extension.
• You have an audio device plugged into TalkSwitch, but have not enabled
(turned on) the Music-on-Hold feature found on the On-Hold/Ringback tab
in the System Information folder.
Problem: Callers hear music and a beeping sound when put on hold at an extension.
• You have an audio device plugged into TalkSwitch, but have not enabled
(turned on) the Music-on-Hold feature found on the On-Hold/Ringback tab
in the System Information folder.
Problem: Callers hear ‘One moment please’ message and then total silence when
the Auto Attendant transfers their call to an extension.
• You have enabled (turned on) the Music-on-Hold feature, but have not
attached an audio device to the MUSIC jack on TalkSwitch.
• There is a problem with the music source. Check all connections and power.
Problem: Callers hear only silence when put on hold at an extension.
• You have enabled (turned on) the Music-on-Hold feature, but have not
attached an audio device to the MUSIC jack on TalkSwitch.
• Make sure you use the ‘Flash’ or ‘Link’ button to put callers on hold. If you
use the ‘Hold’ button on a regular phone, callers will be placed on hold at the
phone and since TalkSwitch didn’t receive a signal to indicate a caller is to be
placed on hold, no music can be played.
Call Routing with Local Extensions and Home Phones (Transfer and Intercom):
Problem: Callers are disconnected when transferring calls from one extension to
another.
• It is possible that if you are using the hookswitch to put callers on hold rather
than a Flash button, you may be holding the hookswitch down too long, and
as a result are actually hanging up on the caller.
Problem: I can’t use my Conference/3-Way Calling feature from the phone company.
• You need to make sure you have checked the box indicating that you have 3-
Way Calling or Transfer and clear on the appropriate lines. This option is
located on the Telephone Lines page in the ‘System Information’ folder of the
configuration.
Appendices
93
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem: Unable to place intercom calls from a Local Extension.
• If the Local Extension has been given ‘Direct Access’ to your telephone lines,
then you need to press ‘Flash’ before intercom calling.
Answering and Fax Machines:
Problem: The answering machine and/or fax machine picks up calls before they
can be answered by telephone extensions.
• Check your settings in the Telephone Lines tab in the ‘Call Handling’ section
in the Software Configuration. The problem may be that your fax
machine/answering machine extension is set to answer calls at the same time
as your telephone extensions. To fix this problem, remove the fax or answer-
ing machine extension from the list of extensions to ring on an incoming call.
Problem: Incoming faxes are not automatically detected and routed to the fax
machine.
On the Auto Attendant tab of the configuration software, check to ensure that you
have chosen the appropriate extension for the field labeled ‘if a fax call is
detected’.
• Not all fax machines emit a CNG tone that TalkSwitch can detect and route.
Therefore, it is wise to consider incorporating an additional method of fax
routing. This may include the use of a distinctive ring number or giving the
caller the option to select the fax extension.
• On average, fax machines/modems will ‘time out’ or disconnect after 25 sec-
onds if they have not connected with another fax machine/modem. If you are
using the ‘User does not make a selection’ option to route incoming faxes, the
fax call may ‘time out’ before it reaches your fax extension. If your Auto
Attendant is lengthy, you may want to shorten it or use another fax routing
option.
• The level of the Auto Attendant is too loud and as a result is overpowering the
CNG tone effecting detection. You may want to lower the volume level of the
Auto Attendant.
Other Possible Local Extension Problems:
Problem: I am unable to access TalkSwitch's Lines with a Local Extension.
• Check your ‘Direct Line Access’ settings on the Local Extension page under
‘System Information’ of the Software Configuration. If a Local Extension has
not been given ‘Direct Access’ to your telephone lines, you must dial (81-88
or 9) to access one of TalkSwitch’s Lines.
94
TalkSwitch User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem: My PC attached (Internal or External) Modem cannot dial out.
• If the extension to which your Modem is attached has not been given ‘Direct
Access’ to telephone lines, you will have to include a Line Hunt Group prefix
(81-88 or 9) before the number you are dialing. For more information about
Dial Out Access and changing your Modem's dial properties, see section 3.2.9,
“External modem telephone line access”.
• You may have to change your Modem's properties so that it waits for a ‘dial-
tone’ before it begins dialing your Dial Up Networking number. For more
information about changing your Modem's properties, see section 3.2.9,
“External modem telephone line access”.
Problem: One of the Local Extensions (telephones) does not ring.
• Some telephones require more ‘voltage’ in order to ring. These phones are
usually the older 'Bell' phones that have mechanical ringers. These phones
are simply too much of a load for TalkSwitch and should not be used as an
extension.
• Make sure the telephone cord you are using between the phone and
TalkSwitch is working properly. Also, check to make sure the ringer is turned
on for your phone.
Problem: Extension(s) ring, but there is no caller.
• This can occur when a caller hangs up after the Auto Attendant has begun to
play. In some areas, the Telephone Company's ‘disconnect/clear’ signal is
weak. This is the reason the Auto Attendant may not pick up the disconnect
signal right away when a caller hangs up. Because the Auto Attendant will
receive no response after playing its message, the call will fall through to your
settings for the 'User does not make a selection' option associated with that
Auto Attendant.
Problem: When I try to access voicemail, I hear a busy tone.
• Check your ‘Direct Line Access’ settings on the Local Extensions page under
'System Information’ of the Software Configuration. If a Local Extension has
been given ‘Direct Access’ to your telephone lines, you must first dial ‘Flash’
before dialing the mailbox. The same applies for dialing other extensions to
initiate intercom calls.
Appendices
95
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B — Using TalkSwitch with Telephone Company
Calling Services
Many of the calling services offered by your local telephone company are compatible
with and enhanced by TalkSwitch's capabilities.
Caller ID (Call Display) — Displays the telephone number and name associated
with an incoming call.
TalkSwitch is capable of regenerating the Caller ID and passing the information
to its Local Extensions when incoming calls are transferred by the Auto Attendant.
TalkSwitch regenerates the Caller ID and passes it only to the selected Local
Extension. If a Local Extension is configured to ring at least twice before the Auto
Attendant answers, TalkSwitch will pass the Caller ID information to that
extension. If a call is transferred from one extension to another, the Caller ID
information will also be passed. TalkSwitch can also use the Caller ID’s time
stamp to set it’s internal clock.
Distinctive Ring — The ability to have more than one telephone number that callers
can dial to reach the same telephone line. (Distinctive Ring is also referred to as:
Ident-A-Ring, Ident-A-Call, Ring Master, Teen Service, Double Number, Personal
Ringing, Ring Plus, Smart Ring Service, Special Ring or Customized Ringing.)
TalkSwitch can detect Distinctive Ring telephone numbers and use them to route
incoming calls automatically. TalkSwitch gives you the ability to use two
Distinctive Ring telephone numbers on all lines. Distinctive Ring numbers on
TalkSwitch's Lines also have access to the Auto Attendant and all of TalkSwitch's
other call routing features.
TalkSwitch’s Distinctive Ring call routing features can be used a number of ways.
Routing fax/modem calls, routing voice messaging, separating home/office
calls, and making use of TalkSwitch's Auto Call Back feature. Each Distinctive
Ring number has a ‘distinctive’ ring cadence or ring sequence, which allows you
to identify the telephone number that was dialed.
Voicemail (Call Answer) — A service which gives callers the opportunity to leave a
message when your phone line is busy or unanswered.
TalkSwitch can work in conjunction with your telephone company's Voicemail
Service.
Call Waiting — If you are already on the phone, the Call Waiting service will emit a
soft beeping sound to let you know you have another call waiting to be answered.
To talk to the other caller when you hear a Call Waiting beep, press the Flash button
twice. To return to the other caller, you will need to press the Flash button twice
again. This service is not recommended since TalkSwitch cannot handle the
second call while the first call is already being routed by the Auto Attendant.
Appendices
97
Download from Www.Somanuals.com. All Manuals Search And Download.
3-Way Calling/Conference — The 3-Way Calling/Conference service allows you to
add a third party to a call already in progress.
The 3-Way Calling/Conference service enhances TalkSwitch’s capabilities
whether you have 1 or more telephone lines. Using only one telephone line
with 3-Way Calling/Conference service, gives you access to TalkSwitch’s Call
Forwarding, Call Back and Call Bridge features.
Centrex/Plexar Transfer — The Centrex Transfer service is similar in function to the
3-Way Calling/Conference service. The primary difference is that two external
parties can still remain in conversation even after you hang up. TalkSwitch can
disconnect after the transfer if you have this service and have enabled the ‘Transfer
and clear’ option on the Miscellaneous page located under ‘Options’.
Using only one telephone line with Centrex Transfer service gives you access to
TalkSwitch’s Call Forwarding, Call Back and Call Bridge features.
Hunt or Rollover — When using two or more lines, calls coming in on a busy line
can be “rolled over” to an available line in a “hunt” pattern that you can set. There
are two types of hunting — Sequential and Circular. Sequential hunting starts at the
number dialed and ends in the last number in the assigned group. Circular hunting
hunts all the lines in the hunting group, regardless of the starting point. (It will only
circle once through the Hunt Group).
TalkSwitch has the same functionality available on all lines and therefore can
work in conjunction with the Hunt and Rollover services.
Call Hold and Flash
TalkSwitch uses ‘Flash’ to put calls on hold. A Flash signal is produced by pressing
the ‘Flash’ or ‘Link’ button on your telephone (Link is another name for Flash). If
you do not have these buttons on your telephone, you can produce a ‘Flash’ by
quickly depressing and releasing the telephone’s ‘Hangup Hook’ or ‘Hook Switch’.
Single Flash — is pressing the ‘Flash’ or ‘Link’ button once. You can also depress
and release the telephone’s ‘Hangup Hook’ or ‘Hook Switch’ once.
Double Flash — is pressing the ‘Flash’ or ‘Link’ button twice. You can also depress
and release the telephone’s ‘Hangup Hook’ or ‘Hook Switch’ twice. When using your
telephone’s ‘Hangup Hook’ to initiate a ‘Double Flash’, do not try to initiate the
second Flash too quickly or you may lose or ‘disconnect’ your caller. Press and release
the ‘Hangup Hook’ once, count to ‘2’, then initiate the second Flash.
98
TalkSwitch User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
When would you use double flash?
1. If TalkSwitch is connected to any other system/service that uses ‘Flash’ to
activate its features (e.g. a Key Telephone System, PBX, or telephone line with
the Centrex service from your phone company).
2. If you are using any of your local telephone company services that are
activated with ‘Flash’ (e.g. Call Waiting, 3-Way Calling/Conference, etc.).
What does Single and Double Flash do?
TalkSwitch and the above-mentioned systems/services use ‘Flash’ to activate their
calling features. TalkSwitch therefore needs a way to tell which (or whose)
features you want to access when you press the ‘Flash’ button.
Using a ‘Single Flash’: places the caller on hold. (The Flash is not passed to
the CO line, solving problems associated with Flash causing a hang-up at
some COs).
Using a ‘Double Flash’: first Flash places the caller on hold, and the second Flash
(if pressed within 2 seconds) tells TalkSwitch to pass a Flash to the CO line to
activate the CO or PBX intended feature.
Appendices
99
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C — Quick Commands and DTMF Functions
These DTMF Quick Commands can be dialed from a Local Extension or an outside
telephone at the Auto Attendant. To enter Command mode, dial
Extension or at the Auto Attendant. If you are requested to enter a password, enter
the Administrator password. Next, enter any command followed by the sign.
at a Local
Command
30
Action
TalkSwitch tells you which mode it is currently using
Switch Modes (x = 1or 2)
3x
4x
Record Auto Attendant (x = 1 to 9)
04x
Erase Auto Attendant messages (x = 1 to 9)
Playback Auto Attendant messages (x = 1 to 9)
Record Auto Call Back Announced Messages 1 – 4
Record Prompted Call Back Announced Message
Erase Call Back Announced Messages 1 – 4
Erase Prompted Call Back Announced Message
Playback Auto Call Back Announced Messages 1 – 4
Playback Prompted Call Back Announced Message
5x
61 – 64
65
061 – 064
065
71 – 74
75
2xx 8<phone number> Enter Remote ext. (2xx) phone number
2xx 980 0
Enter Remote ext. (2xx) Turn off “Same Line Connect”
2xx 980 1
Enter Remote ext. (2xx) Turn on “Same Line Connect”
2xx 9 <Hunt Group>
Enter Remote ext. (2xx) “Connect using:” Hunt Group
(Hunt Group = 9, 81-88)
1xx 61
1xx 60
Enable ‘Do not Disturb’ at the Local Extension
Disable ‘Do not Disturb’ at the Local Extension
Appendices 101
Download from Www.Somanuals.com. All Manuals Search And Download.
DTMF descriptions dialed from a Local Extension.
DTMF
Function performed
Notes
111-114
Intercoms a Local Extension
Direct dial from dialtone.
x represents the Unit ID
211-218
300-309
Dials a Remote Extension (associated
with an external phone number).
Direct dial from internal dialtone.
x represents the Unit ID
Dials an Extension Ring Group - 10 in
total for the entire system. Mapped to
local extension(s), with specific fall
through options.
Direct dial from internal dialtone.
<flash> if
connected to a
caller
Puts caller on hold.
After putting a caller on hold, you receive
internal dialtone.
<flash> at
It retrieves the most recent caller put on To retrieve the caller on hold for the most
internal dialtone
hold.
time, dial 7 at internal dialtone
<flash> at
external dialtone
Switches to internal dialtone. Used
mainly when an extension has Direct
Line Access enabled.
Dialed when connected to an outside line.
Dials into a voice mailbox.
To transfer a caller to a mailbox, press
111-114
211-218
410-419
'flash' to place a call on hold, then
111-
114,
211-218, or
410-419 and
hang up.
x represents the Unit ID
1x1-1x8
2x1-2x8
4x0-4x9
Internal voicemail retrieval/access.
accesses the mailbox associ-
ated to that extension.
Direct dial
111-114,
211-218,
or 410-419 from internal dialtone to
retrieve voicemail.
x represents the Unit ID
<flash>4
0
Completes a transfer and returns to
internal dialtone
Action performed after putting a caller on
Hold then dialing an indented destination.
Direct dial
0 at dial tone to make an
External P.A. Access
announcement through the attached
external P.A. system.
102
TalkSwitch User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
DTMF
Notes
Function performed
<flash>5
Action performed after putting a caller on Hold
and dialing an intended destination.
Disconnects current caller and
reconnects immediately to the last
caller put on hold.
Press 'flash' to place a call on hold, then assign
Call Parking Spots - 10 in total for the
entire system.
500-509
a parking spot (park orbit)
500-509.
Auto Park a call
510
Press ‘flash’, then
510 to place a caller in
the next available parking spot (park orbit).
Parked Call Retrieval
500-509
Direct dial
500-509 from dial tone to pick
up a parked call.
Press 'flash' to put the first caller on hold, dial
another extension or external number, then
press 'flash' 6.
Conference Call for 3 parties.
<flash>6
61
Direct Dial
61 at a local extension. User will
Enables 'Do Not Disturb' at the
current extension
hear confirmation. Reminder is played
every time the extension is picked up.
Direct Dial
60 at a local extension. User will
Disables 'Do Not Disturb' at the
current extension.
60
hear confirmation.
62 toggles DND on/off.
7 + 1xx
Call Pick up - Extension Specific
Direct dial from dial tone to pick up a call
ringing at another extension at anytime includ-
ing after the Auto Attendant answers.
Direct dial from dial tone or by pressing ‘flash’
then 7 to cycle through on a first in / first out
basis.
<flash>7
80
Hold Retrieve - used for retrieving any
calls placed on hold at that extension.
Accesses Same Line Connect when
transferring an outside caller to
another outside number.
Put the caller on Hold, dial 80, and then dial
the outside number. Hang up to complete the
transfer. Can only be used when the line has
3-Way Calling/Conference or Transfer
(Centrex/Plexar) service.
Line Hunt Groups used to access a
line.
Direct dial from dial tone.
81-88, 9
8
Play music source through PA output
Direct dial from dial tone to toggle on or off
music through the PA port. Useful for office
background music.
Call Pick up
Direct dial from dial tone to pick up a call
ringing at any other extension.
9
Enters command mode
Direct dial
at a Local Extension
If you have Direct Line Access enabled at your Local Extension, then you must first press ‘flash’
before using most of the functions listed.
Appendices 103
Download from Www.Somanuals.com. All Manuals Search And Download.
DTMF descriptions dialed at the Auto Attendant message
Digit dialed
Function performed
0
User Defined — Mapped to an Extension, Ring Group, Auto
Attendant, Voice mailbox, Announcement or perform no
action.
111-114
211-218
Dials Local Extensions
Dials Remote Extensions associated with an external phone
number. Functionality similar to a Local Extension. x represents
the Unit ID number (1-4).
300-309
1,2,3,4,5
Dials Extension Ring Groups — 10 in total for the entire
system. Mapped to Local Extensions(s), with specific fall
through options.
User Defined — Mapped to an Extension, Ring Group, Auto
Attendant, Voice mailbox, Announcement or Perform no
action.
6
Enters Call Back configuration.
7(xxx...)
PBX Transfer — A flash hook transfer with disconnect after
dialed.
81-88, 9
80
Access to line Hunt Groups for Call Bridge — Password
protected at the Auto Attendant.
Call Bridge using Same Line Connect. Requires 3-Way
Calling/Conference on the line.
111-114
211-218
410-419
410-419
Enter Internal voicemail to leave a message or listen to an
announcement. If you press 8 during the greeting, you can
access messages. x represents the Unit ID number.
Callers can directly also dial 400 series mailboxes
Internal voicemail retrieval/access.
x represents the Unit ID number.
111-114
211-218
410-419
104
TalkSwitch User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D — Safety Precautions and Regulatory Information
Safety Precautions
Before using TalkSwitch, please review and ensure the following safety instructions
are adhered to:
1. Read, Follow and Retain Instructions — All safety and operating instructions
should be read before operating the equipment, followed and retained for
future reference.
2. Heed Warnings — All warnings on the equipment and in the operating
instructions should be adhered to.
3. Do not operate in environments where the temperature is below 0 degrees
Celsius or 32 degrees Fahrenheit. If the product was shipped in cold weather,
please let the system warm up at room temperature for at least 2 hours
before plugging it in to a power outlet.
4. Moisture — Do not place TalkSwitch in a high humidity environment.
5. Heat — Never place TalkSwitch near heat sources such as radiators, floor
registers or direct sunlight.
6. Power Supply — The equipment should only be connected to an approved
power supply of the type described in the operating instructions or marked
on the equipment. Use only the power adapter supplied with TalkSwitch.
7. Damage requiring service — Do not attempt to service the TalkSwitch
yourself. Unplug TalkSwitch and refer servicing to a licensed technician
when:
• The plug or power cord has been damaged.
• TalkSwitch has been exposed to moisture.
• TalkSwitch does not appear to be operating properly or exhibits a
marked change in performance.
Appendices 105
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Notices
FCC and IC Warnings
This equipment complies with ACTA TIA/EIA/IS-968A and Part 68 of the Federal
Communications Commission (FCC) rules in the United States. It also complies
with regulations RSS210 and CS-03 of Industry Canada and Science Canada.
This equipment also complies with Part 15 of the FCC Rules, as well as ICES003
of Industry Canada. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired
operation of the device.
FCC Part 15:
NOTE: This equipment has been tested and found to comply with the limits for
a “CLASS B” Digital Device pursuant to Part 15 of the FCC rules. These limits
are designed to provide a reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio
frequency energy, and if not installed and used in accordance with these
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different to that which the
receiver is connected.
• Consult the dealer or an experienced Radio/TV technician for help.
This CLASS B Digital apparatus meets all requirements of the Canadian interference-
causing equipment regulations.
Changes or modifications not expressly approved by TalkSwitch could void the user’s
authority to operate the equipment.
106
TalkSwitch User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
ACTA TIA/EIA/IS-968A, FCC Part 68 and IC CS-03:
Notice: The Industry Canada label identifies certified equipment. This certification
means that the equipment meets telecommunications network protective,
operational and safety requirements as prescribed in the appropriate Terminal
Equipment Technical Requirements document(s). The Department does not
guarantee that the equipment will operate to the user's satisfaction.
Before installing this equipment, users should ensure that it is permissible to be
connected to the facilities of the local Telecommunications Company. The
equipment must also be installed using an acceptable method of connection. The
customer should be aware that compliance with the above conditions may not
prevent degradation of service in some situations.
Repairs to certified equipment should be coordinated by a representative designated
by the supplier. Any repairs or alterations made by the user to this equipment, or
equipment malfunctions, may give the telecommunications company cause to
request the user to disconnect the equipment.
Users should ensure, for their own protection, that the electrical ground connections
of the power utility, telephone lines and internal metallic water pipe system, if
present, are connected together. This precaution may be particularly important in
rural areas.
Caution: Users should not attempt to make such connections themselves, but should
contact the appropriate electric inspection authority, or electrician, as appropriate.
A label is located on the underside of the base unit containing both the FCC
registration number and Ringer Equivalency Number (REN) or the IC registration
number and Load Number. You must, upon request, provide this information to your
local telephone company.
The REN is used to determine the quantity of devices that may be connected to the
telephone line. Excessive RENs on the telephone line may result in the devices
not ringing in response to an incoming call. In most, but not all areas, the sum
of RENs should not exceed five (5.0). To be certain of the number of devices that
may be connected to a line, as determined by the total RENs, contact the local
Telephone Company.
This equipment is compatible with inductively coupled hearing aids.
Appendices 107
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Should you experience trouble with this telephone equipment, Model: CT-TS01, for
repair or warranty information please contact your reseller. See Appendix E,
“TalkSwitch One Year Limited Warranty”, for more information.
If the equipment is causing harm to the telephone network, the Telephone Company
may request that you disconnect the equipment until the problem is corrected.
This equipment cannot be used on public coin telephone services provide by the
telephone company. Connection to party line service is subject to state tariffs.
The FCC requires that you connect your cordless telephone to the nation-wide
telephone network through a modular telephone jack (USOC, RF11C, RJ11W, or RJ14).
Your telephone company may discontinue your service if your equipment causes
harm to the telephone network. They will notify you in advance of disconnection, if
possible. During notification, you will be informed of your right to file a complaint
to the FCC.
Occasionally, your telephone company may make changes in its facilities, equipment,
operation, or procedures that could affect the operation of your equipment. If so, you
will be given advance notice of the change to give you an opportunity to maintain
uninterrupted service.
108
TalkSwitch User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix E — TalkSwitch One-Year Warranty
The Original end-user customer acknowledges that he or she has read the limited One-
Year Warranty and Warranty Disclaimers and understands the same and agrees to be
bound by its terms and conditions.
TalkSwitch, a division of Centrepoint Technologies Inc. (“TalkSwitch”) warrants to
the original end-user customer ("Customer") that each new TalkSwitch product
shall be substantially free from defects in materials and workmanship under normal
use for a period of one (1) year from the date of the original purchase (proof of
purchase required). The exclusive remedy and entire liability under this warranty
will be for repair or replacement on a like-for-like basis at TalkSwitch’s option.
The above warranty shall not apply to product defects resulting from (a) improper
maintenance or installation; (b) misuse, neglect or accident; (c) damage from
moisture or corrosive environments; (d) use of the power adapter with supply voltages
other than that for which it is specified; (e) static discharges; (f) high voltage surges;
(g) electrostatic discharges; (g) operation outside the product's specification; or (h)
failure to follow product instructions.
The warranty is void where (a) the serial number has been altered, removed or
effaced; or (b) the product has been used in an application, country, region, locality,
or connected to any network, other than those for which the product was intended
to operate.
TalkSwitch shall not have any obligation to repair or replace product until the
Customer returns defective product to TalkSwitch. Any replacement product may be
either new or like-new, and may contain remanufactured parts, equivalent to new
in performance.
EXCEPT FOR THE EXPRESS WARRANTIES SET FORTH ABOVE, AND TO THE
EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCTS AND STORAGE MEDIA
ARE SUPPLIED ON AN “AS IS” BASIS AND THERE ARE NO WARRANTIES,
REPRESENTATIONS OR CONDITIONS WHETHER EXPRESSED OR IMPLIED,
WRITTEN OR ORAL, ARISING BY STATUTE, OPERATION OF LAW, COURSE OF
DEALING, USAGE OF TRADE OR OTHERWISE, WITH RESPECT TO THE PRODUCT.
TALKSWITCH SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES OR
CONDITIONS OF MERCHANTABILITY, SATISFACTORY QUALITY, DURABILITY,
FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT.
IN NO EVENT SHALL TALKSWITCH BE LIABLE FOR ANY SPECIAL, INCIDENTAL,
CONSEQUENTIAL, INDIRECT OR SIMILAR DAMAGES, INCLUDING ANY LOST
PROFITS, LOST DATA, OR OTHER INCIDENTAL OR CONSEQUENTIAL OR PUNITIVE
DAMAGES, WHETHER BASED ON CONTRACT, TORT (INCLUDING WITHOUT
Appendices 109
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITATION, NEGLIGENCE), OR ANY OTHER LEGAL THEORY, WHETHER OR NOT
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, OR WHETHER SUCH DAMAGES
ARE FORSEEABLE. IN ANY EVENT, THE TOTAL AGGREGATE LIABILITY OF
TALKSWITCH FOR DIRECT DAMAGES SHALL NOT EXCEED THE PURCHASE PRICE
OF THE PRODUCT.
This warranty gives specific rights, and Customer may have other rights subject to
jurisdiction. To the extent any part of this limited warranty statement is inconsistent
with such local law, that part shall be deemed modified to be consistent with such
local law.
DOC Compliance
This digital apparatus does not exceed the Class B limits for radio noise emissions for
digital apparatus as set out in the Radio Interference Regulations of the Canadian
Department of Communications.
The FCC Statement is located in Appendix D, “Safety Precautions and Regulatory
Information”.
Warranty Service
To be eligible to obtain warranty service you must retain proof of purchase and contact
your reseller for warranty details. If you fail to provide proof of purchase, your reseller
and TalkSwitch, a division of Centrepoint Technologies Inc. (“TalkSwitch”) will not
be able to provide you with any kind of warranty service.
To obtain warranty service, products must be sent to your reseller or a service facility
designated by TalkSwitch. The original end-user purchaser shall pay all shipping
charges, duties and taxes for products sent to TalkSwitch for warranty service.
TalkSwitch shall pay for return of the product to the end-user purchaser.
110
TalkSwitch User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
To obtain Warranty service:
If purchased from a reseller:
Contact your reseller and obtain a Warranty Return Authorization (WRA) number
if required.
If purchased from TalkSwitch: Please contact the Technical Support department at
TalkSwitch to obtain an WRA number — (866) 393-9960 toll free in continental
North America or (613) 725-2466. Please have your model and serial number
available when you call.
If the product is being shipped from outside of Canada, the following statement must
be included on the package. ‘Canadian Goods Being Returned to Canada’.
Failure to obtain a WRA number and include the necessary information will result in
the package being refused.
Appendices 111
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix F — Return Policy
Products purchased from a reseller:
Check with your reseller on the specific details regarding their return policy.
Products purchased directly from TalkSwitch:
Contact TalkSwitch, a division of Centrepoint Technologies Inc. (“TalkSwitch”) for
details regarding the return policy. TalkSwitch will provide you with a Return
Merchandise Authorization (RMA) number and all the necessary instructions for
returning the product.
TalkSwitch will not accept product returns outside of its return policy.
If the product is being shipped from outside of Canada, the following statement must
be included on the package. 'Canadian Goods Being Returned to Canada'.
Failure to obtain an RMA number from TalkSwitch and include the necessary
information will result in the package being refused.
Important: The TalkSwitch Return Policy applies only for products purchased directly
from TalkSwitch. The Return Policy for products purchased from an authorized
TalkSwitch dealer is determined by the dealer (the retail outlet where the product was
purchased). Please contact your retailer for information regarding their return policy;
do not return the product directly to TalkSwitch
For information regarding product servicing, please refer to the TalkSwitch One Year
Limited Warranty.
Appendices 113
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix G — Specifications
Extension Interface
Loop range
On hook voltage
Off hook loop voltage source
Off hook loop current
Ringing voltage
Ringing frequency
Total supported ringing load
Trunk type
0 to 600 ohms
35 volts
35 volts
23 to 40 mA
90 volts RMS
20 Hz – True Sine wave
5 REN
Loop start
RJ-11, 2 pin
600 ohms
-2.4 dBm
DTMF only
Yes
Connector type
Interface impedance
Dial tone level
Signaling type
Flash hook supported
C.O. Interface
Interface impedance
Trunk type
Connector type
Ringing impedance
Ringing sensitivity
REN
900/600 ohms
Loop start
RJ-11, 4-pin
3,900 ohms
45 volts RMS @ 20Hz
1
Longitudinal balance
Signal level
69 dB
-10 dB
Caller ID support
Distinctive ring supported
All lines
Yes
System
C.O. interfaces
2
4
1
1
Extension interfaces
RS-232, 9 pin interface
USB interface
Memory expansion
1 hour, 2 hours,
4.5 hours, 9 hours
TalkSwitch Memory Cards
Appendices 115
Download from Www.Somanuals.com. All Manuals Search And Download.
System
Music input
P.A. output
Power source
Phono jack (mono)
Phono jack (mono)
AC wall adapter
120VAC/16VAC 1.1A
Power switch
DTMF detectors
Push Button
12 @ -3dBm to -30dBm
Dial tone generators
Ring detectors
Power-failure pass through
1
2
Extension 4 connects to Line 1
Dimensions
Weight
(H) 51.6mm x (W) 203.2mm x
(L) 213.4mm
0.675 kg
Approvals
ACTA TIA/EIA/IS-968A
and FCC Part 68
Industry Canada CS-03
FCC Part 15B
Industry Canada ICES003
Power Adapter complies with
UL and CSA
116
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
Appendix H — TalkSwitch and Power Interruptions
TalkSwitch settings and configurations:
In the event of a power failure, your TalkSwitch settings and configurations will not
be lost.
TalkSwitch’s feature settings (configuration) are stored in an EEPROM. An EEPROM
is a form of non-volatile memory. Non-volatile memory means that your feature
settings (configurations) remain in TalkSwitch’s memory despite interruptions in
TalkSwitch’s power supply.
Calling Features:
In the event of a power failure, no TalkSwitch features or capabilities will be available
other than:
• Local Extension 114 can make or receive calls on Line 1
In the event of a power return, all TalkSwitch features and capabilities will be
re-established.
Mode Scheduling and Power Interruptions:
When the power supply to TalkSwitch has been interrupted, TalkSwitch’s internal
clock will continue to run for up to 12 hours. If you have enabled TalkSwitch’s
Automatic Mode Scheduling feature and it has been longer than 12 hours,
TalkSwitch will not function properly until the internal clock is reset via a Caller ID
call or with the TalkSwitch configuration software. When power is restored to
TalkSwitch, TalkSwitch will check the time and determine the mode it should be in
according to the configuration and set itself to that mode.
To check the current mode of operation, dial
command mode then enter a password if required. Next, dial 30 then . TalkSwitch
will report the current mode.
at a Local Extension to enter
Appendices 117
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
* (Star/Asterisk Sign)
Call Back
The character on the bottom left of your
touchtone telephone keypad.
A TalkSwitch feature which, once
activated, instructs TalkSwitch to call you
back at a preset Out-of-Office telephone
number. You can then access TalkSwitch’s
Call Bridge feature. TalkSwitch offers two
ways to activate Call Back — Prompted
and Auto.
# (Pound Sign)
The character on the bottom right of
your touchtone telephone keypad. It is
also commonly called the number sign.
Call Bridge
3-Way Calling/Conference
A TalkSwitch feature which ‘bridges’
together calls from two different remote
locations. Call Bridge allows you to place
long distance calls from your office
telephone lines even when you are
out of the office.
A service provided by telephone
companies which allows you to connect
parties on three different telephone lines
together for one conversation.
3-Way Conference Call
Connecting three parties together for one
telephone conversation. TalkSwitch offers
its own 3-Way Conference feature and
also allows you to use the 3-Way
Conference (Calling) service provided by
local telephone companies.
Call Forward
A TalkSwitch feature which forwards calls
to one of 10 or more Remote Extensions.
Caller ID
A service provided by telephone
companies which transmits information
about incoming calls (callers name and
telephone number). The Caller ID
information is transmitted between the
first and second ring.
Analog
All sound actually begins in the form of
sine waves and must be in this form to be
heard by the human ear. Analog devices
(phones, answering machines, etc.)
transmit and receive sound in the form
of ‘sine waves’. The telephone lines in
your home are also designed to carry
analog signals (sine waves). TalkSwitch
is an analog device and will work with
any other analog device or telephone
system.
Call Waiting
A service provided by telephone
companies which allows you to accept a
second incoming call on a telephone line
that is already in use. Call Waiting allows
you to 'toggle' from one caller to the
other.
Auto Attendant Message
TalkSwitch’s electronic attendant. A
self-recorded message that greets and
directs callers to select an extension
number based on information provided
in the message.
Download from Www.Somanuals.com. All Manuals Search And DGowlnolosasad.ry 119
Central Office
Conference Call
Your local telephone company or public
exchange network.
Connecting three or more parties
together for one conversation.
Centrex/Plexar
Configuration
Central Office Exchange Service. A type of
PBX service offered by the telephone
company on a ‘pay per service’ basis. All
call switching occurs at a local telephone
station instead of a company's premises.
The way a system is setup. For TalkSwitch
the configuration is the collection of
values or options you have chosen for
each of TalkSwitch’s features. Together,
the settings for each of these features
(The configuration) determine what
TalkSwitch will do. TalkSwitch can be
configured using the Configuration
software or Telephone Keypad Commands.
CNG
A ‘chirping’ tone emitted by fax modems
and most fax machines to initiate contact
with another fax machine/modem.
Connector
The part of a cable that plugs into a port
or interface to connect one device to
another. Most connectors are either male
or female.
COM Port
Communications Port. Internal virtual
pathways used to transmit data to and
from a PC's exterior Serial Port and
software running on the PC. The majority
of PCs have four Com Ports: COM1,
COM2, COM3, and COM4. Most software
programs gain access to the Com Ports
via system interrupts (IRQs) and only
two IRQs are reserved for the four ports.
If you have two devices using Com Ports
that share an IRQ, you cannot use the
devices simultaneously. Typically, COM1
and COM3 use IRQ4, while COM2 and
COM4 use IRQ3.
CTI
Computer Telephony Integration.
Dialtone
A tone used by the telephone company to
indicate to the user that the line is ‘free’
and available for making calls.
Dial Up Networking
A component in Microsoft Windows that
enables you to connect your computer to
a network via a modem.
Communications Software
Software that makes it possible to send
and receive data over telephone lines via
modems.
Digit
Any whole number from 0 to 9. The
numbers on your telephone keypad can
also be referred to as digits.
Computer Telephony Integration
Refers to systems that enable a computer
to act as a call center, accepting
Distinctive Ring
incoming calls and routing them to the
appropriate device or person. Today's CTI
systems, like TalkSwitch, are quite
sophisticated and can handle all sorts
of incoming and outgoing
The ability to have more than one
telephone number that callers can dial to
reach the same telephone line. Each
Distinctive Ring number has a distinctive
ring cadence or ring sequence.
communications, including phone
calls, faxes, and Internet messages.
TalkSwitch recognizes Distinctive Ring 1
as 2 short rings. Distinctive Ring 2 is
120
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
Flash button
identified as 3 short rings. (Distinctive
Ring is also referred to as: Ident-A-Ring,
Ident-A-Call, Ring Master, Teen Service,
Double Number, Personal Ringing, Ring
Plus, Smart Ring Service, Special Ring or
Customized Ringing).
A button on your telephone. Pressing
the Flash button has the same effect as
pressing the Link button or depressing
and releasing the ‘hang up’ (switch)
hook on a telephone. All of these actions
will send a signal to TalkSwitch to put
calls on or off hold.
Driver
A program that controls a device. Every
device, whether it is a printer, disk drive,
or keyboard, must have a driver program.
A driver acts like a translator between the
device and programs that use the device.
Home phone
A home phone is any telephone using the
same telephone line as one of TalkSwitch’s
Lines, but is not plugged directly into the
back of TalkSwitch as an extension.
DTMF
Auto Call Back
Dual Tone Multi-Frequency. The system
used by touchtone telephones. DTMF
assigns a specific frequency, or tone, to
each key so that it can easily be identified
by a microprocessor.
Allows you to activate Call Back by
dialing one of TalkSwitch’s telephone
numbers, letting the call ring at least
once and then hanging up.
Extension (Local)
Intercom
A Local Extension is any telephone or
analog device (answering machine, fax,
etc.) that is plugged into one of the
‘Extensions’ jacks located on the back
panel of your TalkSwitch.
A dedicated voice service within a
specified user environment. TalkSwitch
offers intercom capabilities between its
Local Extensions.
Interface
Something that connects two separate
entities. A user interface is the part of a
program that connects the computer with
a human operator (user).
Extension (Remote)
A call forwarding number that can be
any telephone number, in any location.
FCC
Keypad Commands
Federal Communications Commission.
The FCC is the United States federal
regulatory agency responsible for the
regulation of interstate and international
communications by radio, television,
wire, satellite and cable.
Combinations of digits that are used to
configure TalkSwitch from a touchtone
telephone.
Keypad (Telephone)
The push buttons on a telephone.
Firmware
Key Telephone System
Firmware is a combination of software
and hardware. More precisely, it is
software (programs or data) that has been
written onto hardware (micro-chips).
Micro-chips (ROMs, PROMs and
EPROMs) that have data or programs
recorded on them are called firmware.
With Key Telephone Systems, access to
telephone lines and calling features is
controlled internally within each tele-
phone unit. Users can gain direct access
to telephone lines, etc. by pressing a key
(or button) on their telephone.
Download from Www.Somanuals.com. All Manuals Search And DGowlnolosasad.ry 121
LED
PBX
Light Emitting Diode. An electronic device
Private Branch Exchange. A PBX is a
that lights up when electricity is passed
through it. LEDs are used in displays on
electronic devices such as computers.
TalkSwitch has five LEDs on its front
panel. They show which telephone is in
use, whether data is being transferred to or
received from an attached PC, and which
Mode setting is in use.
private telephone network used within an
Enterprise. Access to telephone lines and
services are controlled by the PBX. A PBX
allows many users (extensions) to share
a smaller number of telephone lines and
have access to additional call handling
benefits (call hold, intercom calling, etc.).
TalkSwitch is a ‘mini’ or ‘micro’ PBX.
Link button
Phone Load
On most telephones, pressing the Link
button has the same effect as pressing the
Flash button or depressing and releasing
the ‘hang up’ (switch) hook. However,
on some telephones, the function of the
Link button is internal to the telephone
and pressing it will have no effect on
TalkSwitch.
See Ringing Equivalency.
Prompt
Recorded instructions delivered by voice
processing units. TalkSwitch provides
prompts for you when using such
features as Call Back, Call Bridge and
Selective Call Forward. Prompts are also
provided when configuring TalkSwitch
using a telephone Keypad and for callers
being put ‘on hold’.
Modem (voice/fax/data)
A modem which supports a switch to
change between voice and data modes.
In data mode, the modem acts like a
regular modem. In voice mode, the
modem acts like a regular telephone.
Modems that support a voice/data switch
have a built-in loudspeaker and
Ringing Equivalency
(Ringer Equivalency Number [REN]) A
number, determined in accordance with
the US Code of Federal Regulations,
which represents the ringer loading effect
on a line. A ringer equivalency number
of 1 represents the loading effect of a
traditional telephone set ringing circuit.
microphone for voice communication.
Modes
A TalkSwitch feature which allows you to
store two distinct incoming call handling
configurations (Mode 1 and Mode 2).
RJ-11
Registered Jacks 11 is the most common
modular jack in the world. It is usually
used to connect ‘single line’ telephonic
devices such as telephones, fax machines
and modems. It supports 2 conductors.
Monitor (TalkSwitch Monitor)
A feature included with the Software
Configuration package. The Monitor
provides a graphical representation of
telephone traffic as it flows through the
TalkSwitch system.
RJ-45
Registered Jacks 45 is a technical term
for a telephone jack that supports 8
conductors and is used generally for
Networking applications.
Network
A group of two or more computer
systems linked together.
122
TDaolkwSnwloaitdchfroUmsWewrwG.Suoimdaenuals.com. All Manuals Search And Download.
Prompted Call Back
Touchtone telephone
Allows you to activate Call Back by dialing
one of TalkSwitch's telephone numbers,
letting the Auto Attendant answer and
then entering the Call Back settings.
A push-button telephone which emits
distinctive (DTMF) tones as different
buttons on the keypad are pressed.
Two Line Telephone
Serial Communication
A telephone which allows you to make
and receive calls on two separate
telephone lines.
A type of electronic communication that,
unlike parallel communication, requires
that data bits be sent one after the other.
Modems rely on serial communication to
send data over telephone lines.
USB
Short for Universal Serial Bus, the USB
connection supports more bandwidth
than a serial or parallel connection.
Serial Port
Serial Ports are physical ‘plug-ins’.
They allow two devices to exchange
information or data. A Serial Cable is
used to connect the two Serial Ports
together.
Virtual Extension
A telephone or other communications
device not physically connected to
TalkSwitch as an extension, but which
provides the same functionality. In
general, the term ‘virtual’ distinguishes
something that is merely conceptual
from something that has physical reality.
TalkSwitch’s Remote Extensions are
virtual extensions.
Telephony
The science of translating sound into
electrical signals, transmitting them, and
then converting them back to sound; that
is, the science of telephones. The term is
used frequently to refer to computer
hardware and software that performs
functions traditionally performed by
telephone equipment.
Voicemail (Call Answer)
A service provided by TalkSwitch or
telephone companies which gives callers
the opportunity to leave a message when
your extension or telephone line is busy
or unanswered.
Tel Lines 1, 2, 3, or 4
A jack or plug-in on the back panel of
TalkSwitch which can accept a RJ-11
plug from either a telephone line or PBX
system. A single line telephone cable can
be plugged into this jack and will
become a usable TalkSwitch Line.
Telephone Keypad
The collection of push buttons on a
touchtone telephone.
Telephone Wall Jack
A wall outlet for a standard telephone
jack.
Download from Www.Somanuals.com. All Manuals Search And DGowlnolosasad.ry 123
|