Software version TC1.0
NOVEMBER 2008
TANDBERG Codec C90
Administrator Guide
D14129.02—NOVEMBER 2008
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Introduction
Contents
Getting started
About the menus
About the settings
Settings Library
Cameras
Appendices
Contact us
Chapter 1
Introduction
Thank you for choosing TANDBERG!
In this chapter...
Your TANDBERG Codec C90 has been
designed to give you many years of safe,
reliable operation.
Intellectual property rights
Trademark
Copyright
Disclaimer
How to read this document
Patent information
Safety instructions
Environmental issues
You will find that some places information
has been copied from other chapters (but
adapted, when needed) to let you have all
the relevant information there and then.
This helps eliminating the need to read
through long sections before you can even
think of getting started.
Our main objective with this user guide is
to address your goals and needs. Please
let us know how well we succeeded!
We recommend you visit the TANDBERG
web site regularly for updated versions of
the manual.
D14129.02—NOVEMBER 2008
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Introduction
Contents
Getting started
About the menus
About the settings
Settings Library
Cameras
Appendices
Contact us
Intellectual Property Rights
Disclaimer
Patent Information
This Administrator Guide and the Products to which it relates contain
information that is proprietary to TANDBERG and its licensors.
Information regarding the Products is found on the page entitled
License Agreements and Patent Information.
The specifications for the Products and the information in this
document are subject to change at any time, without notice, by
TANDBERG.
The products described in this manual are covered by one or more of
the following patents:
US6,584,077
US5,003,532
US7,034,860
US6.731.334
US5,838,664
US5,768,263
US7,010,119
GB1338127
US5,600,646
US5,991,277
EP01953201
Every effort has been made to supply complete and accurate
information in this Administrator Guide, however, TANDBERG
assumes no responsibility or liability for any errors or inaccuracies that
may appear in this document.
This Administrator Guide may be reproduced in its entirety,
including all copyright and intellectual property notices, in limited
quantities in connection with the use of the Products. Except for
the limited exception set forth in the previous sentence, no part of
this Administrator Guide may be reproduced, stored in a retrieval
system, or transmitted, in any form, or by any means, electronically,
mechanically, by photocopying, or otherwise, without the prior written
permission of TANDBERG. Requests for such permission should be
addressed to tandberg@tandberg.com.
INTELLECTUAL PROPERTY RIGHTS
Other patents pending.
The Products that are covered by this Administrator Guide are
protected under copyright, patent, and other intellectual property
rights of various jurisdictions. Any applicable software licenses and
any limited warranty are located in the License Information section in
this TANDBERG Codec C90 Administrator Guide.
list
This Product is
Copyright Notice
COPYRIGHT © 2008, TANDBERG
All rights reserved.
Trademark
The product that is covered by this Administrator Guide is protected
under copyright, patent, and other intellectual property rights of
various jurisdictions. This product is Copyright © 2008, Tandberg
Telecom AS. All rights reserved. This product includes copyrighted
software licensed from others.
TANDBERG® is a registered trademark belonging to Tandberg ASA.
Other trademarks used in this document are the property of their
respective holders.
COPYRIGHT © 2008, TANDBERG
All rights reserved.
A document describing the copyright notices and the terms and
Philip Pedersens vei 20
Navigate to User manuals > TANDBERG Codec C90 Copyright and
License Information to download the pdf.
1366 Lysaker, Norway
Tel: +47 67 125 125 Fax: +47 67 125 234
E-mail: tandberg@tandberg.com
IMPORTANT: USE OF THIS PRODUCT IS SUBJECT IN ALL CASES
TO THE COPYRIGHT RIGHTS AND THE TERMS AND CONDITIONS
OF USE REFERRED TO ABOVE. USE OF THIS PRODUCT
CONSTITUTES AGREEMENT TO SUCH TERMS AND CONDITIONS.
D14129.02—NOVEMBER 2008
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Introduction
Contents
Getting started
About the menus
About the settings
Settings Library
Cameras
Appendices
Contact us
Water and Moisture
Power Connection and Hazardous
Voltage
•
•
•
If the cabinet has been damaged.
Safety Instructions
Do not operate the apparatus under or near water –
for example near a bathtub, kitchen sink, or laundry
tub, in a wet basement, near a swimming pool or in
other areas with high humidity.
If the apparatus seems to be overheated.
For your protection please read these safety
instructions completely before you connect the
equipment to the power source. Carefully observe
all warnings, precautions and instructions both on
the apparatus and in these operating instructions.
The product may have hazardous voltage inside.
If the apparatus emits smoke or abnormal
odor.
•
Never attempt to open this product, or any
peripherals connected to the product, where
this action requires a tool.
•
If the apparatus fails to operate in
accordance with the operating instructions.
•
Never install jacks for communication cables
in wet locations unless the jack is specifically
designed for wet locations.
•
•
•
This product should always be powered from
an earthed power outlet.
Retain this manual for future reference.
Accessories
•
Do not touch the product with wet hands.
Never connect attached power supply cord to
other products.
Use only accessories specified by the
manufacturer, or sold with the apparatus.
Cleaning
In case any parts of the product has visual
damage never attempt to connect main power,
or any other power source, before consulting
service personnel
Unplug the apparatus from communication lines,
mains power-outlet or any power source before
cleaning or polishing. Do not use liquid cleaners
or aerosol cleaners. Use a lint-free cloth lightly
moistened with water for cleaning the exterior of
the apparatus.
Communication Lines
Do not use communication equipment to report a
gas leak in the vicinity of the leak.
•
•
The plug connecting the power cord to the
product/power supply serves as the main
disconnect device for this equipment. The
power cord must always be easily accessible.
IMPORTANT!
Route the power cord so as to avoid it being
walked on or pinched by items placed upon or
against it. Pay particular attention to the plugs,
receptacles and the point where the cord exits
from the apparatus.
Ventilation
There should always be a distance of minimum
10 cm (0.33 ft) free space in the front of the codec.
Do not block any of the ventilation openings of the
apparatus. Never cover the slots and openings with
a cloth or other material. Never install the apparatus
near heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers)
that produce heat.
•
•
Do not tug the power cord.
If the provided plug does not fit into your outlet,
consult an electrician.
Min. 10 cm
Do not place the product in direct sunlight or close
to a surface directly heated by the sun.
•
Never install cables, or any peripherals, without
first unplugging the device from its power
source.
Lightning
Never use this apparatus, or connect/disconnect
communication cables or power cables during
lightning storms.
Servicing
WARNING!
•
Do not attempt to service the apparatus
Make sure the Codec
C90 never rest on
the front panel.
yourself as opening or removing covers may
expose you to dangerous voltages or other
hazards, and will void the warranty. Refer all
servicing to qualified service personnel.
Dust
Do not operate the apparatus in areas with high
concentration of dust.
•
Unplug the apparatus from its power source
and refer servicing to qualified personnel under
the following conditions:
Vibration
•
If the power cord or plug is damaged or
frayed.
Do not operate the apparatus in areas with
vibration or place it on an unstable surface.
•
•
•
If liquid has been spilled into the apparatus.
If objects have fallen into the apparatus.
If the apparatus has been exposed to rain
or moisture
•
If the apparatus has been subjected to
excessive shock by being dropped.
D14129.02—NOVEMBER 2008
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Introduction
Contents
Getting started
About the menus
About the settings
Settings Library
Cameras
Appendices
Contact us
TANDBERG’s Environmental Policy
European Environmental Directives
Information for Recyclers
Environmental Issues
Environmental stewardship is important to
TANDBERG’s culture. As a global company with
strong corporate values, TANDBERG is committed
to following international environmental legislation
and designing technologies that help companies,
individuals and communities creatively address
environmental challenges.
As a manufacturer of electrical and electronic
equipment TANDBERG is responsible for
compliance with the requirements in the European
Directives 2002/96/EC (WEEE - Waste Electrical
and Electronic Equipment) and 2002/95/EC
(RoHS).
As part of compliance with the European
WEEE Directive, TANDBERG provides recycling
information on request for all types of new
equipment put on the market in Europe after
August 13th 2005.
Thank you for buying a product which contributes
to a reduction in pollution, and thereby helps save
the environment. Our products reduce the need for
travel and transport and thereby reduce pollution.
Our products have either none or few consumable
parts (chemicals, toner, gas, paper).
Please contact TANDBERG and provide the
following details for the product for which you
would like to receive recycling information:
The primary aim of the WEEE Directive and RoHS
Directive is to reduce the impact of disposal of
electrical and electronic equipment at end-of-life.
The WEEE Directive aims to reduce the amount
of waste electrical and electronic equipment sent
for disposal to landfill or incineration by requiring
producers to arrange for collection and recycling.
The RoHS Directive bans the use of certain heavy
metals and brominated flame retardants to reduce
the environmental impact of WEEE which is in
landfill or incinerated.
TANDBERG’s environmental objectives are to:
•
•
•
•
•
•
Model number of TANDBERG product
Your company’s name
Contact name
•
Develop products that reduce energy
consumption, CO2 emissions, and traffic
congestion
Address
•
•
•
Provide products and services that improve
quality of life for our customers
Telephone number
E-mail.
Produce products that can be recycled or
disposed of safely at the end of product life
TANDBERG has implemented necessary process
changes to comply with the European WEEE
Directive (2002/96/EC) and the European RoHS
Directive (2002/95/EC).
Comply with all relevant environmental
legislation.
Digital User Guides
TANDBERG is pleased to announce that we have
replaced the printed versions of our user guides
with digital versions available on the TANDBERG
environmental benefits of this are significant. The
user guides can still be printed locally, whenever
needed.
Waste Handling
In order to avoid the dissemination of hazardous
substances in our environment and to diminish the
pressure on natural resources, we encourage you
to use the appropriate recycling systems in your
area. Those systems will reuse or recycle most
of the materials of your end of life equipment in a
sound way.
TANDBERG products put on the market after
August 2005 are marked with a crossed-out
wheelie bin symbol that invites you to use
those take-back systems.
Please contact your local supplier, the regional
www.tandberg.com/recycling if you need more
information on the collection and recycling system
in your area.
D14129.02—NOVEMBER 2008
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Getting started
Contents
Introduction
About the menus
About the settings
Settings Library
Cameras
Appendices
Contact us
Chapter 2
Getting started
This chapter introduces you to the codec
and gets you up and going.
In this chapter...
Assemble your system
Using the remote control
Turn on the system
This guide has been divided into several
chapters, all of which provide different
information. You can access the chapters
directly by clicking on the menu bar at the
top of this page.
Verify IP address settings
Setting a static IP address
Add the system to the network
Verify your settings
Time zone settings
About monitors
D14129.02—NOVEMBER 2008
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Getting started
Contents
Introduction
About the menus
About the settings
Settings Library
Cameras
Appendices
Contact us
Assemble your system
The illustration shows you the basic setup when connecting your monitor, PC,
camera, microphone, loudspeakers (if applicable), LAN and line voltage to your
codec.
1
OPTIONAL:
Loudspeakers
OPTIONAL:
Audio from PC
Video
from PC
LAN/
Ethernet
Monitor
(Audio from HDMI 1 or
Line Out 1–2)
Mains Power
Cable
Microphone
OPTIONAL:
You may connect additional
microphones
OPTIONAL:
You may connect a second camera.
Main camera:
Video from
PrecisionHD 1080p
(extra camera not included). Extra camera will
require separate power supply and control
cabling. Consult the documentation supplied
with the extra camera for details.
OPTIONAL:
Dual monitor setup
Connect the second
monitor to HDMI 3
Main camera:
Camera Control to
PrecisionHD 1080p
Make sure the codec has been switched off and
disconnected from the line voltage whenever
connecting or disconnecting other equipment.
!
D14129.02—NOVEMBER 2008
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Getting started
Contents
Introduction
About the menus
About the settings
Settings Library
Cameras
Appendices
Contact us
Using the Remote Control
ARROW UP/DOWN: Use
the up and down
arrow keys to navigate in
the menu.
FUNCTION KEYS: Each key reflects
a soft key on screen and represents
shortcuts and advanced functions.
The functions keys
in the upper part of
the remote control
reflects the soft keys
on screen.
ARROW LEFT: Press
ARROW RIGHT: Press
the right arrow key
to expand the selected
menu item or to move
to the right in a text
field.
the left arrow key
to go one step back
in the menu or to
move to the left in a
text field.
... and the middle
part of the remote
control is used to
handle the video
part of the call.
1.@
4 ghi
2 abc
5 jkl
8 tuv
0
def 3
mno 6
wxyz 9
... while the lower
part of the remote
control resembles
very much the
keypad of a mobile
phone
OK/SELECT: Press the OK/
Select key to confirm your
choice odresf 3election.
2 abc
7 pqrs
abc/123
#
1.@
MICROPHONE: Press the
Microphone key
the microphone
PRESENTATION: Press the
Presentation key to show/hide
a presentation.
Batteries
PHONE BOOK: Press
the Phone Book key to
display the local phone
book.
LAYOUT: Press the Layout
Make sure the remote control has
working batteries (4 x AAA batteries).
key to display the layout
menu, then select a view
in the menu.
VOLUME: Press
ZOOM: Press
the + or – on the
Volume key to adjust
the codec volume.
the + or – on the Zoom
key to zoom the camera
in and out.
2 abc
def 3
1.@ HOME: Press the
Home key to go back
to the mainmmnoenu.
D14129.02—NOVEMBER 2008
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Getting started
Contents
Introduction
About the menus
About the settings
Settings Library
Cameras
Appendices
Contact us
Using the Remote
CALL KEY
ALPHANUMERIC KEYPAD
Control, cont...
INITIATE CALL: Select a name from the Phone book or enter the
name, number or URI and press the Call key to initiate the call.
Use the keypad in the same way as you would
use a cellular phone.
SHORTCUT TO RECENT CALLS: Use the Call button as a
shortcut to Recenble.
The functions keys
in the upper part of
the remote control
reflects the soft keys
on screen.
0-9, a-z, period (.), @, space, *:
Press a key repeatedly to toggle
between the options displayed
on each key.
END CALL, STANDBY:
Press the End Call
key to end a call, or
when idle, press and
hold the key to go into
standby mode.
... and the middle
part of the remote
control is used to
handle the video
part of the call.
1.@
abc
def 3
1.@
4 ghi
2 abc
5 jkl
8 tuv
0
def 3
mno 6
wxyz 9
abc/123 #: Press the # key to
toggle between lower case
characters and numbers.
4 ghiCLEAR: Premssnot6he Cancel
key to remove characters
5 jkl
... while the lower
part of the remote
control resembles
very much the
keypad of a mobile
phone
7 pqrs
7 pqrisn a text field.
8 tuv
wxyz 9
abc/123
#
Waking up the system
IR sensor range (DIP switch setting)
Press any key on the remote control to wake up the system.
The IR sensor has a short and long range. Open the battery cover and remove
the batteries to set the DIP switch.
•
•
Short range (1 m): Move the DIP switch down
Long range: Move the DIP switch up.
Press the HOME
key to show the
menu on screen
The DIP
switch
1.@
4 ghi
2 abc
5 jkl
8 tuv
0
def 3
mno 6
wxyz 9
rs
abc/123
#
Touch the rubber
line sensors along
the sides to wake
up the system
D14129.02—NOVEMBER 2008
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Getting started
Contents
Introduction
About the menus
About the settings
Settings Library
Cameras
Appendices
Contact us
Turn on the system
If you need to set a static IP address
Go to IP Settings to set static IP addresses:
•
•
•
•
Turn on the codec and wait a few minutes for the system to start
1
2
3
Make sure the remote control has the batteries installed.
1. Navigate to Settings > Administrator Settings > IP Settings.
Press Home (
) on the remote control to show the menu on screen
2. Set IP Assignment to Static. Press the left arrow key to go back one step
When you can see the menu on screen, proceed to Step 2.
3. Enter the IP Address, Subnet Mask and Gateway address in the address fields.
The sequence is shown below.
Show the menu:
4. Press OK to save the changes, or Cancel to leave without saving.
•
Press Home (
) on the remote control to show the menu on screen
5. Press Home (
) to exit.
Navigate in the menu:
•
Use the arrow keys on the remote control to navigate up and down in
the menus
Confirm your choice:
•
To confirm your choice, press OK ( ) on the remote control
Verify IP address settings
Go to System Information to verify the IP address:
1. Navigate to Settings > System Information
2. When the IP address is automatically assigned from a DHCP server, the
Address of the codec is shown on the System Information page.
3. Press Home (
) to exit.
D14129.02—NOVEMBER 2008
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Getting started
Contents
Introduction
About the menus
About the settings
Settings Library
Cameras
Appendices
Contact us
Add the system to the network
Verify your settings
Your service provider should have provided you with the information you
need to get on-line.
We strongly recommend that you verify the settings by inspecting the System
Information list.
4
5
For H323 type of communication, this will include such things as system
name, H323 alias, gatekeeper address, etc. For SIP type of communication,
similar type of information will be supplied.
You do this by accessing the System Information in the same way as you did
when you verified you IP address setting.
For networks administrated through TMS (TANDBERG Management Suite),
your TMS administrator will be able to assist you when configuring.
Go to System Information to verify the settings:
1. Navigate to Settings > System Information
The H323 and SIP settings are configured from the Administrator Settings
menu:
2. Verify the previous configurations. For example, if you successfully registered
to a SIP server the Status will show Registered. If the registration failed the
Status will show Not registered.
Navigate to Settings > Administrator Settings > Advanced Settings.
3. Press Home (
) to exit.
•
Expand the items in need of modification and enter the information
supplied by your service provider.
Time zone settings
Verify the date and time to see if the time zone settings need to be adjusted. The
date and time is located in the upper right corner on screen.
6
Go to time zone settings to set the NTP (date and time) settings:
1. Navigate to Settings > Administrator Settings > Time > Zone
2. You may need to consult the NTP Time Zone expression list to find the
right expression. Go to the Appendices section and the NTP Time Zone
expression to see a complete overview.
3. Enter the time zone expression for where the system is located. The default
value is Etc/UTC.
NOTE: Spelling correctly is important when entering the NTP Time Zone
expression
4. Press Save to save the changes, or Cancel to leave without saving.
5. Press Home (
) to exit.
D14129.02—NOVEMBER 2008
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Getting started
Contents
Introduction
About the menus
About the settings
Settings Library
Cameras
Appendices
Contact us
About main and dual monitors
The video outputs at Codec C90
The main monitor
The main monitor can be connected to the default video output HDMI
1 or one of the other outputs which are HDMI 3, DVI-I 2 or DVI-I 4.
Connecting to HDMI 1
When you connect the main monitor to the default video output on
Codec C90 the menu, icons and other information on screen (OSD -
on screen display) will show on this monitor.
DVI-I 4
Connecting to DVI-I 2, DVI-I 4, HDMI 3
HDMI 3
(the default connector
for the dual monitor)
When connecting the main monitor to another video output, and no
menu shows on screen, you must run a shortcut on the remote control
to reset the resolution and move the OSD to this output.
The resolution will be set to the default value, which is
1280x720@60Hz for HDMI and 1024x768@60Hz for DVI.
DVI-I 2
The menu on screen, icons and other information (OSD - on screen
display) will be moved to the selected output.
HDMI 1
(the default connector
for the main monitor)
Key sequence
If connected to DVI-I 2, DVI-I 4 or HDMI 3 you must run the following
shortcut or key sequence on the remote control.
Dual monitors
When you want to run a dual monitor setup, connect the second
monitor to video output HDMI 3 on Codec C90.
•
Disconnect * # * # 0 x # (where x is output 2, 3 or 4)
Example: Set DVI-I 2 as the OSD output:
Disconnect * # * # 0 2 #
•
Dual monitor configuration
Go to Administrator settings to set the monitor to dual:
You can also set the resolution and the OSD output by setting up a
serial port connection and run API commands. See the Codec C90
System Integrator Guide for information about API commands.
1. Navigate to Settings > Administrator Settings > Video > Output >
Monitor
2. Set the Monitor to Dual.
3. Press Home (
) to exit.
D14129.02—NOVEMBER 2008
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
About the menus
Contents
Introduction
Getting started
About the settings
Settings Library
Cameras
Appendices
Contact us
Chapter 3
About the menus
In this chapter...
Explains the menu system
D14129.02—NOVEMBER 2008
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
About the menus
Contents
Introduction
Getting started
About the settings
Settings Library
Cameras
Appendices
Contact us
About the menus
The menu system is divided into three levels:
1. The Home menu
HOME
The Home menu
Press the
Home key on the remote control to open the Home menu:
2. The Settings menu
3. The Administrator Settings menu
•
•
•
•
Open the Call menu to make a call
Open the Presentation menu to select a presentation source
Open the Camera control menu to pan, tilt or zoom the camera
Open the Settings menu to configure the system
Navigate in the menus
Use the remote control to navigate in the menus:
•
•
•
Use the arrows down/up to select a menu item
Use the arrow right to expand the selection
Use the arrow left to go one step back
SETTINGS
The Settings menu
Change a value
The Settings menu lets the user:
•
Select a value from a drop down list and press
the OK button to save, or press the left arrow to
leave without saving.
•
•
•
•
•
•
•
Open the Layout control menu to control the screen layout, including selfview
Select Wallpaper to chose a background picture on screen
Open the Call settings menu to configure the default bit rate and auto answer settings
Select Ring tones to chose a ring tone
•
Enter a value/text in a value/text field. Press
Save to save the change or Cancel to leave
without saving.
Open the System Information page to see an overview of the system configurations
Open the Administrator settings menu to configure the system
Select Restart to restart the system.
ADMINISTRATOR SETTINGS
The Administrator settings menu
The Administrator settings menu lets the user:
•
•
Open the IP address menu to configure the IP settings
Open the Advanced configuration menu to access the system configuration settings
In this guide we will concentrate on what’s behind
the Administrator Settings menu and leave the
other menus to be explained in the Codec C90
User Guide.
Changes in the administrator settings may
affect the behavior of the system and should
be configured by the system administrator.
You can download the Codec C90 User
Guide from our web site.
!
D14129.02—NOVEMBER 2008
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Admin. Settings menu
Contents
Introduction
Getting started
About the menus
Settings Library
Cameras
Appendices
Contact us
Chapter 4
The Settings menu
In this chapter...
Explaining the
administrator settings
D14129.02—NOVEMBER 2008
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Admin. Settings menu
Contents
Introduction
Getting started
About the menus
Settings Library
Cameras
Appendices
Contact us
Administrator settings
HOME
If IP Assignment is set to DHCP the IP
address, Subnet Mask and Gateway
will automatically be assigned to the
codec from the DHCP server.
The Administrator settings menu lets the user
configure the IP settings and the system settings.
SETTINGS
The IP Settings menu
The IP Settings are found in the IP Settings menu
as well as in the Advanced Configuration menu in
the Network settings.
IP SETTINGS
DHCP
Changes in the administrator settings may
affect the behavior of the system and should
be configured by the system administrator.
!
Each setting is explained in the
administrator The settings library section.
ADMINISTRATOR SETTINGS
Navigate in the menus
Use the remote control to navigate in the menus:
•
•
•
Use the arrows down/up to select a menu item
Use the arrow right to expand the selection
Use the arrow left to go one step back
IP SETTINGS
Static
Change a value
•
Select a value from a drop down list and press
the OK button to save, or press the left arrow to
leave without saving.
•
Enter a value/text in a value/text field. Press
Save to save the change or Cancel to leave
without saving.
If IP Assignment is set to Static the IP
address, Subnet Mask and Gateway
must be defined manually:
•
On the remote control, press
the arrow down key to highlight
an address field. Enter the IP
address, Subnet Mask and
Gateway address.
In this guide we will concentrate on what’s behind
the Administrator Settings menu and leave the
other menus to be explained in the Codec C90
User Guide.
•
Press OK to confirm the new
value or Left arrow to cancel.
Changes in the administrator settings may
affect the behavior of the system and should
be configured by the system administrator.
You can download the Codec C90 User
Guide from our web site.
!
D14129.02—NOVEMBER 2008
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Admin. Settings menu
Contents
Introduction
Getting started
About the menus
Settings Library
Cameras
Appendices
Contact us
Administrator settings, cont...
The Administrator settings menu lets the user:
HOME
•
Open the IP address menu to configure the IP
settings
ADVANCED CONFIGURATIONS
SETTINGS
•
Open the Advanced configuration menu to
access the system configuration settings
The Advanced configuration menu
The Advanced configuration defines the system
settings. The system settings are structured in
a hierarchy, making up a database of system
settings.
ADMINISTRATOR SETTINGS
Changes in the administrator settings may
affect the behavior of the system and should
be configured by the system administrator.
!
Each setting is explained in the
administrator The settings library section.
Navigate in the menu
Search
1. Use the up and down arrow keys on the remote control to navigate in the menu
Enter the as many characters as needed, until the setting you are
searching for displays in the list.
2. Press the right arrow key to expand the selected menu item or to move to the
right in a text field
ADVANCED CONFIGURATIONS
3. Press the left arrow key to go one step back in the menu or to move to the left in
a text field
htt
4. Press the OK/Select key to confirm your choice or selection
NetworkServices HTTP Mode: On
NetworkServices HTTPS Mode: On
ADVANCED CONFIGURATIONS
In this guide we will concentrate on what’s behind
the Administrator Settings menu and leave the
other menus to be explained in the Codec C90
User Guide.
You can download the Codec C90 User
Guide from our web site.
D14129.02—NOVEMBER 2008
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
The settings library
Contents
Introduction
Getting started
About the menus
About the settings
Cameras
Appendices
Contact us
Chapter 5
Administrator Settings Library
In this chapter...
Audio
This chapter gives a detailed description of
the administrator settings
Cameras
Conference
Do Not Disturb
H323
The administrator settings defines the
system settings and are structured in a
hierarchy, making up a database of system
settings.
Network
Network Services
Phone Book Server
Provisioning
Serial Port
SIP
NOTE: The description of the Administrator
settings are preliminary, and subject to
change.
Standby
System Unit
Video
D14129.02—NOVEMBER 2008
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
The settings library
Contents
Introduction
Getting started
About the menus
About the settings
Cameras
Appendices
Contact us
Audio Input Microphone [1..8] Level: <0..18>
Defines the input level of each microphone in steps of 1dB from 0dB to 18 dB. Addresses the specific
microphone.
Description of the administrator settings
In the following pages you will find a complete list of the administrator settings. The examples
shows either the default value or an example of a value.
Please see the Audio Level tabels in the Codec C90 System Integrators Guide for a complete overview of
the menu values represented in dB.
We recommend you visit the TANDBERG web site regularly for updated versions of the manual.
Range: 0 to 18 dB
Example: Audio Input Microphone 1 Level: 14
Note: The description of the Administrator settings are preliminary, and subject to change.
Audio Input Microphone [1..8] EchoControl Mode: <On/Off>
The echo canceller continuously adjusts itself to the audio characteristics of the room and compensate for
any changes it detects in the audio environment. If the changes in the audio conditions are very significant
the echo canceller may take a second or two to re-adjust. Addresses the specific microphone.
The Audio settings
On: Echo Control is normally set to On to prevent the far end from hearing their own audio. Once selected,
echo cancellation is active at all times.
Audio Volume: <0..100>
Sets the volume level [0-100] on the loudspeaker output in steps of 0.5dB from -34.5dB to 15dB. Volume 0
= Off.
Off: Echo Control should be switched Off if external echo cancellation or playback equipment is used.
Example: Audio Input Microphone 1 EchoControl Mode: On
The volume level bar which is displayed on screen, when using the remote control, goes from 0 to 20.
Range: The volume level goes from 0 to 100
Audio Input Microphone [1..8] EchoControl NoiseReduction: <On/Off>
The system has a built-in noise reduction which reduces constant background noise (e.g. noise from air-
conditioning systems, cooling fans etc.). In addition, a high pass filter (Humfilter) reduces very low frequency
noise. Requires the Echo Control Mode to be enabled for the specified microphone. Addresses the specific
microphone.
Volum level equals Audio gain value
0 equals 0
1 equals -34.5 dB
70 equals 0.0 dB
On: The Noice Reduction should be set to On in the presence of low frequency noise.
Off: Turns Noise Reduction Off for the specified microphone input.
100 equals 15.0 dB
Example: Audio Volume: 70
Example: Audio Input Microphone 1 EchoControl NoiseReduction: On
Audio Input Microphone [1..8] Type: <Microphone/Line>
Audio Input HDMI [3, 4] Mode: <On/Off>
The microphone inputs are intended for electret type microphones. The microphone inputs are balanced
with 48 V phantom power. The microphone input can be set to line or microphone mode. Addresses the
specific microphone.
Determines whether or not the audio channel on the HDMI input should be active. The HDMI 3 and HDMI 4
has audio channels. Addresses the specific Audio HDMI input.
On: Set to On to enable the audio channel on the HDMI input 3 or 4.
Off: Set to On to disable the audio channel on the HDMI input.
Microphone: Phantom voltage and pre-amplification is On
Line: Select Line when you have a standard balanced line input. The phantom voltage and pre-amplification
is Off.
Example: Audio Input HDMI 3 Mode: On
Example: Audio Input Microphone 1 Type: Line
Audio Input Line [1..4] Mode: <On/Off>
Determines whether or not an Audio Line input is active. Addresses the specific Audio Line input.
Audio Input Microphone [1..8] Mode: <On/Off>
On: Set to On to enable the Audio Line input.
By default, all inputs are enabled. Just plug in an audio source and it is active. Audio inputs that are On
will automatically be mixed. Unconnected inputs will automatically be muted. Addresses the specific
microphone.
Off: Set to Off to disable the Audio Line input.
Example: Audio Input Line 1 Mode: On
On: Turns the microphone On.
Off: Connected but unused inputs should be set to Off to prevent audio/noise from the inputs.
Example: Audio Input Microphone 1 Mode: On
D14129.02—NOVEMBER 2008
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
The settings library
Contents
Introduction
Getting started
About the menus
About the settings
Cameras
Appendices
Contact us
Audio Input Line [1..4] Level: <0..18>
Audio Output Line [2, 4..6] Type: <Analog>
Defines the input level of each Line input in steps of 1dB from 0dB to 18 dB. Addresses the specific Audio
Line input.
Line output 2, 4, 5, 6 are dedicated analog outputs, hence type can be set to analog only.
Example: Audio Output line 2 type: analog
Please see the Audio Level tabels in the Codec C90 System Integrators Guide for a complete overview of
the menu values represented in dB.
Audio Output Line [1..6] Level: <-18..0>
Range: 0 to 18 dB
Defines the output level of the specified Audio Output Line in steps of 1dB from -18dB to 0dB. Addresses
the specific Audio Line output connector.
Example: Audio Input Line 1 Level: 10
Please see the Audio Level tabels in the Codec C90 System Integrators Guide for a complete overview of
the menu values represented in dB.
Audio Input Line [1..4] Channel: <Left/Right/Mono>
Defines whether the Audio Line input is a mono signal or part of a multichannel signal.
Left: The Audio Line input signal is the left channel of a stereo signal.
Right: The Audio Line input signal is the right channel of a stereo signal.
Mono: The Audio Line input signal is a mono signal.
Range: -18 to 0 dB
Example: Audio Output Line 1 Level: -10
Audio Output Line [1..6] Channel: <Left/Right/Mono>
Defines whether the Audio Line output is a mono signal or part of a multichannel signal.
Left: The Audio Line output signal is the left channel of a stereo signal.
Right: The Audio Line output signal is the right channel of a stereo signal.
Mono: The Audio Line output signal is a mono signal.
Example: Audio Input 3 Channel: Left
Audio Input Line [3..4] LoopSuppression: <On/Off>
Loop suppression detects whether a delayed signal loop is present from an audio Line output to an audio
Line input on the codec. If a loop is detected this unwanted feedback is suppressed. This function may be
useful if a DVD player is connected to both an input and an output of the codec. If the DVD player is in stop
or record mode it will loop the output signal from the codec directly back to the codec’s input.
Example: Audio Output Line 1 Channel: left
On: Set to On to activate Loop Suppression. When Loop Suppression is activated the codec will detect
delayed signal loops from line output 3 to line input 3 and from line output 4 to line input 4. (Only line input 3
and 4, and line output 3 and 4 are intended connected to a DVD player in the current setup.)
Audio Output HDMI [1, 3] Mode: <On/Off>
Determines whether or not the audio channel on the HDMI output should be active. Addresses the specific
Audio HDMI output.
Off: Set to Off to deactivate Loop Suppression. Note! Line input 1 and 2 do not support Loop Suppression,
hence Loop Suppression can be set to Off only for these outputs.
On: Set to On to enable the audio channel on the HDMI 1 or HDMI 3 output.
Off: Set to On to disable the audio channel on the HDMI 1 or HDMI 3 output.
Example: Audio Input Line 3 LoopSuppression: On
Example: Audio Output HDMI 1 mode: On
Audio Output Line [1..6] Mode: <On/Off>
Determines whether or not an Audio Line output is active. Addresses the specific Audio Line output.
Audio SoundsAndAlerts KeyTones Mode: <On/Off>
Determines whether or not the system should produce a sound every time a key on the remote control is
pressed.
On: Set to On to enable the Audio Line output.
Off: Set to Off to disable the Audio Line output.
On: There will be a sound indicator when pressing keys on the remote control.
Off: The remote control Key Tones is switched off.
Example: Audio Output Line 1 Mode: On
Example: Audio SoundsAndAlerts KeyTones Mode: Off
Audio Output Line [1, 3] Type: <Auto/SPDIF>
Determines if the Audio Line output is an analog or digital type output. Addresses the specified Audio Line
output (1 or 3).
Auto: The system will select analog or digital (SPDIF) mode depending on the detected Audio Module. If
a TANDBERG Digital NAM is detected then SPDIF mode will be selected, otherwise analog mode will be
selected.
SPDIF: Set to SPDIF when you want the Audio Line 1 or 3 output to be in digital mode. This will disable
Output Line 2 and 4.
Example: Audio Output Line 1 Type: Auto
D14129.02—NOVEMBER 2008
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
The settings library
Contents
Introduction
Getting started
About the menus
About the settings
Cameras
Appendices
Contact us
Audio SoundsAndAlerts RingVolume: <0..100>
Cameras Camera [1..7] Flip: <On/Off>
Defines the volume of the ring tone for an incoming call.
Applies to cameras which supports Flip mode. Enables the video on screen to be flipped upside down.
Addresses the specific camera. TANDBERG PrecisionHD 1080p camera auto detects if the camera is
mounted upside down, hence flip mode is not necessary.
The ring tone volume level bar which is displayed on screen, when using the remote control, goes from 0 to
20.
On: When set to On the video on screen is flipped. This setting is used with cameras that can be mounted
upside down, but cannot auto detect that the camera is mounted upside down.
Range: The ring tone volume goes from 0 to 100
Off: Set to Off to display the video on screen the normal way.
Volum level equals Audio gain value
0 equals 0
Example: Cameras Camera 1 Flip: Off
1 equals -34.5 dB
Cameras Camera [1..7] IrSensor: <On/Off>
70 equals 0.0 dB
The Camera IR setting determines whether the infrared receiver at the camera should be enabled or not.
The IR sensor LED is located in the front of the camera and flickers when the IR sensor is activated from the
remote control. Addresses the specific camera.
100 equals 15.0 dB
Example: Audio SoundsAndAlerts RingVolume: 50
On: Set to On to enable the IR sensor on the camera.
Off: Set to Off to disable the IR sensor on the camera.
Audio SoundsAndAlerts RingTone: <Marbles/IceCrystals/Polaris/Alert/Discrete/Fantasy/
Jazz/Nordic/Echo/Rhythmic>
Example: Cameras Camera 1 IrSensor: On
Defines the ringtone for incoming calls.
Range: Select a tone from the list of ringtones.
Cameras Camera [1..7] Brightness Mode: <Auto/Manual>
Define whether to control the camera brightness manually or to have it automatically adjusted by the system.
Addresses the specific camera.
Example: Audio SoundsAndAlerts RingTone: Jazz
Auto: When set to Auto, the camera brightness is automatically set by the system.
Manual: Set to Manual to enable manual control of the camera brightness, e.g. the level of the brightness
level setting will be used for the camera.
The Camera settings
Example: Cameras Camera 1 Brightness Mode: auto
Cameras Camera [1..7] Backlight: <On/Off>
Backlight is used to compensate for lights shining directly at the camera (usually the sun entering the
window) to avoid a too dark image from the room. Addresses the specific camera.
Cameras Camera [1..7] Brightness Level: <1..31>
Define the Brightness Level for the camera. Requires the Brightness Mode to be set to manual. Addresses
the specific camera.
On: Set to On to turn on the backlight compensation.
Off: Set to Off to turn the backlight compensation off.
Range: 1-31
Example: Cameras Camera 1 Brightness Level: 1
Example: Cameras Camera 1 Backlight: Off
Cameras Camera [1..7] Whitebalance Mode: <Auto/Manual>
Define whether to control the camera whitebalance manually or to have it automatically adjusted by the
system. Addresses the specific camera.
Cameras Camera [1..7] Mirror: <On/Off>
The Mirror mode makes it possible to reverse the the video on screen. Normally you will see yourself in the
same view as other people sees you. With mirror enabled the experience will be like looking at yourself in a
mirror. Addresses the specific camera.
Auto: When set to Auto, the camera will continuously adjust the whitebalance depending on the camera
view.
On: Set to On to see the selfview in mirror mode, e.g. the selfview is reversed and the experience of selfview
is as seeing yourself in a mirror.
Manual: Set to Manual to enable manual control of the camera whitebalance, e.g. the level of the
whitebalance level setting will be used for the camera.
Off: Set to Off to see the selfview in normal mode, e.g. the experience of selfview is as seeing yourself as
other people see you.
Example: Cameras Camera 1 Whitebalance Mode: auto
Example: Cameras Camera 1 Mirror: Off
D14129.02—NOVEMBER 2008
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
The settings library
Contents
Introduction
Getting started
About the menus
About the settings
Cameras
Appendices
Contact us
Cameras Camera [1..7] Whitebalance Level: <1..16>
The Conference settings
Specify which camera to control. Define the Whitebalance Level for the camera. Requires the Whitebalance
Mode to be set to manual. Addresses the specific camera.
Conference [1..1] AutoAnswer Mode: <On/Off>
The Autoanswer setting determines whether an incoming call is put through automatically or manually.
Range: 1-16
Example: Cameras Camera 1 Whitebalance Level: 1
On: The system will automatically answer all incoming calls.
Off: All incoming call must be answered manually by pressing the OK key or the green Call key on the
remote control.
Cameras Camera [1..7] Focus Mode: <Auto/Manual>
Determines whether the camera should be in auto focus or manual focus mode. Addresses the specific
camera.
Example: Conference 1 AutoAnswer Mode: Off
Auto: When set to Auto the focus will be updated throughout the call. When moving the camera, the system
will use auto focus for a few seconds to set the right focus of the new camera position. After a few seconds
auto focus is turned off to prevent continuous focus adjustments of the camera.
Conference [1..1] AutoAnswer Delay: <0..50>
Defines how long (in seconds) an incoming call has to wait before it is answered automatically by the
system. Requires the Autoanswer Mode to be enabled.
Manual: If set to Manual the focus is adjusted manually.
Range: 0-50 seconds
Example: Cameras Camera 1 Focus Mode: auto
Example: Conference 1 AutoAnswer Delay: 0
Cameras Camera [1..7] Gamma Mode: <Auto/Manual>
Conference [1..1] IncomingMultisiteCall Mode: <Allow/Deny>
The Incoming Multisite Call setting determines whether or not the system should accept incoming calls to an
already active conference.
Applies to cameras which supports Gamma mode. The Gamma Mode setting enables for gamma
corrections. Gamma describes the nonlinear relationship between image pixels and monitor brightness.
Addresses the specific camera. The TANDBERG PrecisionHD 1080p camera do not need Gamma Mode.
The TANDBERG PrecisionHD camera do support Gamma Mode.
Allow: When set to Allow, and with an ongoing MCU call/conference, the user can accept another incoming
call. This will result in the incoming call being added to the MCU conference.
Auto: Auto is the default and the recommended setting.
Manual: In severe light conditions, you may switch mode to manual and specify explicitly which gamma
table to use by setting the Gamma Level.
Deny: The system will not accept incoming calls when you are in a call. The calling side will receive a busy
signal.
Example: Cameras Camera 1 Gamma Mode: auto
Example: Conference 1 IncomingMultisiteCall Mode: Allow
Cameras Camera [1..7] Gamma Level: <0..7>
Conference [1..1] FarEndControl Mode: <On/Off>
By setting the Gamma Level you can select which gamma correction table to use. This setting may be useful
in difficult lighting conditions, where changes to the the brightness setting does not provide satisfactory
results. Requires the Gamma Mode to be set to Manual. Addresses the specific camera.
Lets you control if the remote side (far end) should be allowed to select your video sources and control your
local camera (pan, tilt, zoom).
On: Set to On when you want the the far end to be able to select your video sources and control your
local camera (pan, tilt, zoom). You will still be able to control your camera and select your video sources as
normal.
Range: 0-7
Example: Cameras Camera 1 Gamma Level: 0
Off: When set to Off the far end can not access any of the features above on your system.
Example: Conference 1 FarEndControl Mode: On
Conference [1..1] Encryption Mode: <Off/BestEffort>
BestEffort: The system will use encryption whenever possible.
In Point to point calls: If the far end system supports encryption (AES-128), the call will be encrypted. If not,
the call will proceed without encryption.
In MultiSite calls: In order to have encrypted MultiSite conferences, all sites must support encryption. If not,
the conference will be unencrypted.
Icons on screen: A padlock with the text “Encryption On” displays on screen, for a few seconds, when the
conference starts.
D14129.02—NOVEMBER 2008
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
The settings library
Contents
Introduction
Getting started
About the menus
About the settings
Cameras
Appendices
Contact us
Off: The system will not use encryption.
The H323 Profile settings
Example: Conference 1 Encryption Mode: BestEffort
H323 Profile [1..1] PortAllocation: <Dynamic/Static>
The H.323 Port Allocation setting affects the H.245 port numbers used for H.323 call signalling.
Conference [1..1] DefaultCall Protocol: <H323/SIP>
Specify the Default Call Protocol to be used when placing calls from the system. The call protocol can also
be defined directly for each call when setting up a call.
Dynamic: The system will allocate which ports to use when opening a TCP connection. The reason for doing
this is to avoid using the same ports for subsequent calls, as some firewalls consider this as a sign of attack.
When Dynamic is selected, the H.323 ports used are from 11000 to 20999. Once 20999 is reached they
restart again at 11000. For RTP and RTCP media data, the system is using UDP ports in the range 2326 to
2487. Each media channel is using two adjacent ports, ie 2330 and 2331 for RTP and RTCP respectively.
The ports are automatically selected by the system within the given range. Firewall administrators should not
try to deduce which ports are used when, as the allocation schema within the mentioned range may change
without any further notice.
H.323: Select H.323 to ensure that calls are set up as a H.323 calls.
SIP: Select SIP to ensure that calls are set up as a SIP calls.
Example: Conference 1 DefaultCall Protocol: H323
Conference [1..1] DefaultCall Rate: <64..6000>
Specify the Default Call Rate to be used when placing calls from the system. The call rate can also be
defined directly for each call when setting up a call.
Static: When set to Static the ports are given within a static predefined range [5555–6555].
Example: H323 Profile 1 PortAllocation: Dynamic
Range: 64-6000 kbps
H323 Profile [1..1] H323Alias ID: <S: 0, 49>
Example: Conference 1 DefaultCall Rate: 766
Lets you specify the H.323 Alias ID which is used to address the system on a H.323 Gatekeeper and will be
displayed in the call lists. Example: “name.surname@company.com”, “My H.323 Alias ID”
Format: String with a maximum of 49 characters
Example: H323 Profile 1 H323Alias ID: “”
The Do not disturb setting
H323 Profile [1..1] H323Alias E164: <S: 0, 30>
The H.323 Alias E.164 defines the address of the system, according to the numbering plan implemented
in the H.323 Gatekeeper. The E.164 alias is equivalent to a telephone number, sometimes combined with
access codes. Example: “9047615901”, “”550092”
DoNotDisturb Mode: <On/Off>
The Do Not Disturb setting determines whether or not there should be an alert on incoming calls.
On: Set to On when you want no alert to incoming calls. The calling side will receive a busy signal when
trying to call the codec.
Format: Compact string with a maximum of 30 characters. Valid characters are 0–9, * and #.
Example: H323 Profile 1 H323Alias E164: “”
Off: This is the default setting. The DoNotDisturb is automatically turned Off if the codec receives any IR
signal from the handheld remote control.
H323 Profile [1..1] CallSetup Mode: <Direct/Gatekeeper>
Example: DoNotDisturb Mode: Off
The H.323 Call Setup Mode defines whether to use a Gatekeeper or Direct calling when establishing H323
calls.
Direct: An IP-address must be used when dialling in order to make the H323 call.
Gatekeeper: The system will use a Gatekeeper to make a H.323 call. When selecting this option the H323
Profile Gatekeeper Address and H323 Profile Gatekeeper Discovery settings must also be configured.
NOTE! Direct H.323 calls can be made even though the H.323 Call Setup Mode is set to Gatekeeper.
Example: H323 Profile 1 CallSetup Mode: Gatekeeper
H323 Profile [1..1] Gatekeeper Address: <S: 0, 64>
Specifies the IP address of the Gatekeeper. Requires the H.323 Call Setup Mode to be set to Gatekeeper
and the Gatekeeper Discovery to be set to Manual.
Format: String with a maximum of 64 characters.
Example: H323 Profile 1 Gatekeeper Address: “10.47.1.58”
D14129.02—NOVEMBER 2008
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
The settings library
Contents
Introduction
Getting started
About the menus
About the settings
Cameras
Appendices
Contact us
H323 Profile [1..1] Gatekeeper Discovery: <Manual/Auto>
Determines how the system shall register to a H.323 Gatekeeper.
The Network settings
Manual: The system will use a specific Gatekeeper identified by the Gatekeeper’s IP-address.
Network [1..1] Assignment: <Static/DHCP>
Defines whether to use DHCP or Static IP assignment.
Auto: The system will automatically try to register to any available Gatekeeper. If a Gatekeeper responds
to the request sent from the codec within 30 seconds this specific Gatekeeper will be used. This requires
that the Gatekeeper is in auto discovery mode as well. If no Gatekeeper responds, the system will not use a
Gatekeeper for making H.323 calls and hence an IP-address must be specified manually.
Static: The IP Address, Subnet Mask and Default Gateway for the system must be specified in the
respective address fields.
DHCP: The system adresses are automatically assigend by the DHCP server.
Changes to this setting requires a restart of the codec.
Example: H323 Profile 1 Gatekeeper Discovery: Manual
Example: Network 1 Assignment: DHCP
H323 Profile [1..1] Authentication LoginName: <S: 0, 50>
The system sends the Authentication Login Name and the Authentication Password to a H.323 Gatekeeper
for authentication. The authentication is a one way authentication from the codec to the H.323 Gatekeeper,
i.e. the system is authenticated to the gatekeeper. If the H.323 Gatekeeper indicates that no authentication
is required, the system will still try to register. Requires the H.323 Gatekeeper Authentication Mode to be
enabled.
Network [1..1] IPv4 Address: <S: 0, 64>
Defines the Static IP address for the system. Only applicable if Static IP assignment is chosen.
Format: Compact string with a maximum of 64 characters.
Format: String with a maximum of 50 characters.
Example: Network 1 IPv4 Address: “10.47.5.100”
Example: H323 Profile 1 Authentication Loginname: “”
Network [1..1] IPv4 SubnetMask: <S: 0, 64>
Defines the IP subnet mask. Only applicable if Static IP assignment is chosen.
H323 Profile [1..1] Authentication Password: <S: 0, 50>
Format: Compact string with a maximum of 64 characters.
The system sends the Authentication Login Name and the Authentication Password to a H.323 Gatekeeper
for authentication. The authentication is a one way authentication from the codec to the H.323 Gatekeeper,
i.e. the system is authenticated to the gatekeeper. If the H.323 Gatekeeper indicates that no authentication
is required, the system will still try to register. Requires the H.323 Gatekeeper Authentication Mode to be
enabled.
Example: Network 1 IPv4 SubnetMask: “255.255.255.0”
Network [1..1] IPv4 Gateway: <S: 0, 64>
Format: String with a maximum of 50 characters.
Defines the IP default gateway. Only applicable if Static IP assignment is chosen.
Format: Compact string with a maximum of 64 characters.
Example: H323 Profile 1 Authentication Password:
Example: Network 1 IPv4 Gateway: “10.47.5.100”
H323 Profile [1..1] Authentication Mode: <On/Off>
On: If the H.323 Gatekeeper Authentication Mode is set to On and a H.323 Gatekeeper indicates
that it requires authentication, the system will try to authenticate itself to the gatekeeper. Requires the
Authentication ID and Authentication Password to be defined on both the codec and the Gatekeeper.
Network [1..1] IPv4 QoS Mode: <Off/Diffserv>
Defines whether IP Diffserv QoS should be used. The QoS (Quality of Service) is a method which
handles the priority of audio, video and data in the network. The QoS settings must be supported by the
infrastructure. DiffServ (Differentiated Services) is a computer networking architecture that specifies a
simple, scalable and coarse-grained mechanism for classifying, managing network traffic and providing
QoS priorities on modern IP networks.
Off: If the H.323 Gatekeeper Authentication Mode is set to Off the system will not try to authenticate itself to
a H.323 Gatekeeper, but will still try a normal registration.
Example: H323 Profile 1 Authentication Mode: Off
Off: When set to Off no QoS method is used.
Diffserv: Select Diffserv and then go to the Diffserv sub-menus (Audio, Data, Signalling and Video) to
configure these settings.
Example: Network 1 IPv4 QoS Mode: diffserv
D14129.02—NOVEMBER 2008
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
The settings library
Contents
Introduction
Getting started
About the menus
About the settings
Cameras
Appendices
Contact us
Network [1..1] IPv4 QoS Diffserv Audio: <0..63>
Network [1..1] DNS Server [1..5] Address: <S: 0, 64>
The DiffServ Audio setting is used to define which priority Audio packets should have in an IP network.
Enter a priority, which ranges from 0 to 63 for the packets. The higher the number, the higher the priority.
These priorities might be overridden when packets are leaving the network controlled by the local network
administrator.
Defines the network addresses for DNS servers. Up to 5 addresses may be specified. If the network
addresses are unknown, please contact your administrator or Internet Service Provider.
Format: String with a maximum of 64 characters.
Example: Network 1 DNS Server [1..5] Address: “”
Audio: A recommended value is DiffServ Code Point (DSCP) is AF41, which equals the value 34. If in doubt,
contact your network administrator.
Range: 0-63
Network [1..1] DNS Domain Name: <S: 0, 64>
DNS Domain Name is the default domain name suffix which is added to unqualified names.
Example: Network 1 IPv4 QoS Diffserv Audio: 0
Example: If the DNS Domain Name is “company.com” and the name to lookup is “MyVideoSystem”, this will
result in the DNS lookup “MyVideoSystem.company.com”.
Network [1..1] IPv4 QoS Diffserv Data: <0..63>
Format: String with a maximum of 64 characters.
The DiffServ Data setting is used to define which priority Data packets should have in an IP network.
Enter a priority, which ranges from 0 to 63 for the packets. The higher the number, the higher the priority.
These priorities might be overridden when packets are leaving the network controlled by the local network
administrator.
Example: Network 1 DNS Domain Name: “company.com”
Data: A recommended value is DiffServ Code Point (DSCP) AF23, which equals the value 22. If in doubt,
contact your network administrator.
Range: 0-63
Example: Network 1 IPv4 QoS Diffserv Data: 0
The Network services settings
Network [1..1] IPv4 QoS Diffserv Signalling: <0..63>
NetworkServices Telnet Mode: <On/Off>
Telnet is a network protocol used on the Internet or local area network (LAN) connections.
The DiffServ Signalling setting is used to define which priority Signalling packets should have in an IP
network. Enter a priority, which ranges from 0 to 63 for the packets. The higher the number, the higher the
priority. These priorities might be overridden when packets are leaving the network controlled by the local
network administrator.
On: The Telnet protocol is enabled.
Off: The Telnet protocol is disabled. This is the default factory setting.
Signalling: A recommended value is DiffServ Code Point (DSCP) AF31 which equals the value 26. If in doubt,
contact your network administrator.
Example: NetworkServices Telnet Mode: Off
Range: 0-63
NetworkServices HTTP Mode: <On/Off>
HTTP is a web-interface for system management, call management such as call transfer, diagnostics and
software uploads.
Example: Network 1 IPv4 QoS Diffserv Signalling: 0
Network [1..1] IPv4 QoS Diffserv Video: <0..63>
On: The HTTP protocol is enabled.
Off: The HTTP protocol is disabled.
The DiffServ Video setting is used to define which priority Video packets should have in an IP network.
Enter a priority, which ranges from 0 to 63 for the packets. The higher the number, the higher the priority.
These priorities might be overridden when packets are leaving the network controlled by the local network
administrator.
Example: NetworkServices HTTP Mode: On
Video: A recommended value is DiffServ Code Point (DSCP) AF41, which equals the value 34. If in doubt,
contact your network administrator.
NetworkServices HTTPS Mode: <On/Off>
HTTPS is a Web protocol that encrypts and decrypts user page requests as well as the pages that are
returned by the Web server.
Range: 0-63
On: The HTTPS protocol is enabled.
Off: The HTTPS protocol is disabled.
Example: Network 1 IPv4 QoS Diffserv Video: 0
Example: NetworkServices HTTPS Mode: On
D14129.02—NOVEMBER 2008
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
The settings library
Contents
Introduction
Getting started
About the menus
About the settings
Cameras
Appendices
Contact us
NetworkServices SNMP Mode: <Off/ReadOnly/ReadWrite>
NetworkServices H323 Mode: <On/Off>
SNMP (Simple Network Management Protocol) is used in network management systems to monitor
network-attached devices (routers, servers, switches, projectors, etc) for conditions that warrant
administrative attention. SNMP exposes management data in the form of variables on the managed
systems, which describe the system configuration. These variables can then be queried (set to ReadOnly)
and sometimes set (set to ReadWrite) by managing applications.
Determines whether the system should be able to place and receive H.323 calls.
On: Set to On to enable the possibility to place and receive H.323 calls.This is the default setting.
Off: Set to Off to disable the possibility to place and receive H.323 calls.
NOTE! Changes in this setting requires the codec to be restarted.
Off: Set to Off when you want to disable the SNMP network service.
Example: NetworkServices H323 Mode: On
ReadOnly: Set to ReadOnly when you want to enable the SNMP network service for queries only.
ReadWrite: Set to ReadOnly when you want to enable the SNMP network service for both queries and
commands.
NetworkServices SIP Mode: <On/Off>
Determines whether the system should be able to place and receive SIP calls.
On: Set to On to enable the possibility to place and receive SIP calls.This is the default setting.
Off: Set to Off to disable the possibility to place and receive SIP calls.
NOTE! Changes in this setting requires the codec to be restarted.
Example: NetworkServices SNMP Mode: ReadWrite
NetworkServices SNMP CommunityName: <S: 0, 50>
Enter the name of the Network Services SNMP Community. SNMP Community names are used to
authenticate SNMP requests. SNMP requests must have a ‘password’ (case sensitive) in order to receive a
response from the SNMP Agent in the codec. The default password is “public”. If you have the TANDBERG
Management Suite (TMS) you must make sure the same SNMP Community is configured there too. Note!
The SNMP Community password is case sensitive.
Example: NetworkServices SIP Mode: On
NetworkServices NTP Mode: <Auto/Manual>
The Network Time Protocol (NTP) is used to synchronize the time of the system to a reference time server.
The time server will subsequently be queried every 24th hour for time updates. The time will be displayed
on the top of the screen. The system will use the time to timestamp messages transmitted to Gatekeepers
or Border Controllers requiring H.235 authentication. The system will use the time to timestamp messages
transmitted to Gatekeepers or Border Controllers that requires H.235 authentication. It is also used for
timestamping Placed Calls, Missed Calls and Received Calls.
Format: String with a maximum of 50 characters.
Example: NetworkServices SNMP CommunityName: “public”
NetworkServices SNMP SystemContact: <S: 0, 50>
Enter the name of the Network Services SNMP System Contact.
Format: String with a maximum of 50 characters.
Auto: The system will use the NTP server, by which address is supplied from the DHCP server in the
network. If no DHCP server is used, or the DHCP server does not provide the system with a NTP server
address, the system will use the static defined NTP server address specified by the user.
Example: NetworkServices SNMP SystemContact: “”
Manual: The system will always use the static defined NTP server address specified by the user.
Example: NetworkServices NTP Mode: Manual
NetworkServices SNMP SystemLocation: <S: 0, 50>
Enter the name of the Network Services SNMP System Location.
Format: String with a maximum of 50 characters.
NetworkServices NTP Address: <S: 0, 64>
Enter the NTP Address to define the network time protocol server address. This address will be used if NTP
Mode is set to Manual, or if set to Auto and no address is supplied by a DHCP server.
Example: NetworkServices SNMP SystemLocation: “”
Format: String with a maximum of 64 characters.
NetworkServices SNMP HostIpAddress [1..3]: <S: 0, 64>
Example: NetworkServices NTP Address: “1.tandberg.pool.ntp.org”
Enter the IP address of up to three SNMP Managers. All traps will then be sent to the hosts listed.
The system’s SNMP Agent (in the codec) responds to requests from SNMP Managers (a PC program etc.).
SNMP Traps are generated by the SNMP Agent to inform the SNMP Manager about important events. Can
be used to send event created messages to the SNMP agent about different events like: system reboot,
system dialing, system disconnecting, MCU call, packet loss etc. Traps can be sent to multiple SNMP Trap
Hosts.
Format: String with a maximum of 64 characters.
Example: NetworkServices SNMP HostIpAddress 1: “”
D14129.02—NOVEMBER 2008
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
The settings library
Contents
Introduction
Getting started
About the menus
About the settings
Cameras
Appendices
Contact us
Provisioning ExternalManager Protocol: <HTTP/HTTPS>
Determines whether or not to use secure management.
The Phone book server settings
HTTP: Set to HTTP to disable secure management. Requires HTTP to be enabled in the Network Services
HTTP Mode setting.
Phonebook Server [1..5] ID: <S: 0, 64>
Enter a name for the external phonebook. Addresses the specific phonebook.
HTTPS: Set to HTTPS to enable secure management. Requires HTTPS to be enabled in the Network
Services HTTPS Mode setting.
Format: String with a maximum of 64 characters.
Example: Phonebook Server 1 ID: “”
Example: Provisioning ExternalManager Protocol: http
Phonebook Server [1..5] URL: <S: 0, 255>
Provisioning ExternalManager Path: <S: 0, 255>
Enter the address (URL) to the external phonebook server. Addresses the specific phonebook server.
If an External Manager address and a path is configured, the system will post an HTTP message to this
address when starting up. When receiving this HTTP posting the External Manager (typically a management
system) can return configurations/commands to the unit as a result. If the DHCP Option 242 is returned in
the DHCP response from the DHCP server the system will interpret this as the External Manager address to
use.
Format: String with a maximum of 255 characters.
Example: Phonebook Server 1 URL: “http://tms.company.com/tms/public/external/
phonebook/phonebook.asmx”
Specifies the path to the External Manager/Management system.
Example: tms/public/external/management/SystemManagementService.asmx
Format: String with a maximum of 255 characters.
Example: Provisioning ExternalManager Path: “”
The Provisioning settings
Provisioning Mode: <Off/TMS>
Provides the possibility of managing the codec (endpoint) by using an external manager/management
system.
The Serial port settings
Off: The system will not try to register to any management system.
TMS: If set to TMS the system will try to register with a TMS server as described in Provisioning
ExternalManager settings. TMS is short for TANDBERG Management System. Please contact your
TANDBERG representative for more information.
SerialPort BaudRate: <9600/19200/38400/115200>
Specify the baud rate (bps) on the COM port (data port). The default value is 38400.
Other default parameters for the COM port are: Parity: None Databits: 8 Stopbits: 1 Flow control: None.
Valid inputs for baud rate: 9600, 19200, 38400, 115200
Example: Provisioning Mode: TMS
Provisioning ExternalManager Address: <S: 0, 64>
Example: SerialPort BaudRate: 38400
If an External Manager address and a path is configured, the system will post an HTTP message to this
address when starting up. When receiving this HTTP posting the External Manager (typically a management
system) can return configurations/commands to the unit as a result. If the DHCP Option 242 is returned in
the DHCP response from the DHCP server the system will interpret this as the External Manager address to
use.
SerialPort LoginRequired: <On/Off>
The Serial Login setting determines whether or not there should be a login when connecting to the COM
port (data port).
Specifies the IP Address to the External Manager/Management system.
Format: String with a maximum of 64 characters.
On: Login is required when connecting to the COM port (data port).
Off: The user can access the COM port (data port) without any login.
Example: Provisioning ExternalManager Address: “”
Example: SerialPort LoginRequired: Off
D14129.02—NOVEMBER 2008
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
The settings library
Contents
Introduction
Getting started
About the menus
About the settings
Cameras
Appendices
Contact us
SIP Profile [1..1] Proxy [1..1] Discovery: <Auto/Manual>
Manual: When Manual is selected, the manually configured SIP Proxy address will be used
The SIP Profile settings
Auto: When Auto is selected, the SIP Proxy address is obtained using Dynamic Host Configuration Protocol
(DHCP).
SIP Profile [1..1] URI [1..1]: <S: 0, 255>
The SIP URI or number is used to address the system. This is the URI that is registered and used by the
SIP services to route inbound calls to the system. A Uniform Resource Identifier (URI) is a compact string of
characters used to identify or name a resource.
Example: SIP Profile 1 Proxy 1 Discovery: Manual
Example: “sip:name@example.com”, “1234”, “1234@example.com”
Format: Compact string with a maximum of 255 characters.
SIP Profile [1..1] Proxy [1..1] Address: <S: 0, 255>
The Proxy Address is the manually configured address for the outbound proxy. It is possible to use a fully
qualified domain name, or an IP address. The default port is 5060 for TCP and UDP but another one can be
provided.
Example: SIP Profile 1 URI 1: “sip:name@example.com”
Format: Compact string with a maximum of 255 characters.
SIP Profile [1..1] DefaultTransport: <UDP/TCP/TLS/Auto>
Select the transport protocol to be used over the LAN.
Example: SIP Profile 1 Proxy 1 Address: “”
UDP: The system will always use UDP as the default transport method.
TCP: The system will always use TCP as the default transport method.
SIP Profile [1..1] Authentication [1..1] LoginName: <S: 0, 50>
This is the user name part of the credentials used to authenticate towards the SIP proxy.
Format: String with a maximum of 50 characters.
TLS: The system will always use TLS as the default transport method. For TLS connections a SIP CA-list
can be uploaded using the web interface. If no such CA-list is available on the system then anonymous Diffie
Hellman will be used.
Example: SIP Profile 1 Authentication 1 LoginName: “”
Auto: The system will try to connect using transport protocols in the following order: TLS, TCP, UDP.
Example: SIP Profile 1 DefaultTransport: Auto
SIP Profile [1..1] Authentication [1..1] Password: <S: 0, 50>
This is the password part of the credentials used to authenticate towards the SIP proxy.
Format: String with a maximum of 50 characters.
SIP Profile [1..1] TlsVerify: <On/Off>
For TLS connections a CA-list can be uploaded from the web interface.
Example: SIP Profile 1 Authentication 1 Password:
On: Set to On to verify TLS connections. Only TLS connections to servers, whom x.509 certificate is
validated against the CA-list, will be allowed.
Off: Set to Off to allow TLS connections without verifying them. The TLS connections are allowed to be
set up without verifying the x.509 certificate received from the server against the local CA-list. This should
typically be selected if no SIP CA-list has been uploaded.
The Standby settings
Example: SIP Profile 1 TlsVerify: Off
Standby Control: <On/Off>
The Standby Control setting determines whether the system should go into standby mode or not.
SIP Profile [1..1] Type: <Auto/Nortel/Microsoft/Cisco/Alcatel/Experimental/Avaya/
Siemens>
Enables SIP extensions and special behaviour for a vendor or provider
On: The system will go into standby mode when the Standby Delay has timed out. Requires the Standby
Delay to be set to an appropriate value.
Auto: Should be used when registering to standard SIP proxy like OpenSer.
Nortel: Must be used when registering to a Nortel MCS 5100 or MCS 5200 PBX.
Microsoft: Must be used when registering to a Microsoft LCS or OCS server.
Cisco: Must be used when registering to a Cisco CallManager version 5 or later.
Alcatel: Must be used when registering to a Alcatel-Lucent OmniPCX Enterprise R7 or later.
Siemens: Must be used when registering to a Siemens HiPath 8000.
Off: The system will not go into standby.
Example: Standby Control: On
Standby Delay: <1..480>
Defines how long (in seconds) the system will wait before it goes into standby mode. Requires the Standby
Control to be enabled.
Telio: Must be used in combination with a Telio subscription (www.telio.no).
Experimental: Can be used if auto is not working Note! This mode is for testing purposes only.
Range: 1-480 seconds
Example: SIP Profile 1 Type: Auto
Example: Standby Delay: 10
D14129.02—NOVEMBER 2008
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
The settings library
Contents
Introduction
Getting started
About the menus
About the settings
Cameras
Appendices
Contact us
The System unit settings
The Video settings
SystemUnit Name: <S: 0, 50>
Video Selfview: <On/Off>
Enter a System Name to define a name of the system unit. If the H.323 Alias ID is configured on the system
then this ID will be used instead of the system name. The system name will be displayed:
The Video Selfview setting determines whether or not the main video source (selfview) should be displayed
on screen.
* When the codec is acting as an SNMP Agent
* Towards a DHCP server
On: Set to On when you want selfview to be displayed on screen.
Off: Set to Off when you do not want selfview to be displayed on screen.
Format: String with a maximum of 50 characters.
Example: Video Selfview: On
Example: SystemUnit Name: “Meeting Room Name”
Video WallPaper: <Summersky/Growing/None>
SystemUnit IrSensor Mode: <On/Off/Auto>
The Video Wallpaper setting determines whether or not a background picture should be displayed on
screen.
The System Unit IR Sensor setting determines whether the infrared receiver on the codec should be enabled
or not. The IR sensor LED is located in the front of the codec and flickers when an ir signal is received from
the remote control.
Summersky, Growing: Select the wallpaper to be displayed on screen.
None: Set to None when you do not want a wallpaper to be displayed on screen.
On: Set to On to enable the IR sensor on the codec.
Off: Set to Off to disable the IR sensor on the codec.
Example: Video Selfview: None
Auto: The system will automatically disable the IR sensor on the codec if the IR sensor at camera is enabled.
Otherwise the IR sensor on the codec will be enabled.
Video MainVideoSource: <1..5>
Define which video input source shall be used as the main video source. The input source is configured to a
video input connector. See the Video Input Matrix table at the back of the codec and the description of the
Video Input Matrix in the Interfaces section.
Example: SystemUnit IrSensor Mode: On
Range: 1-5 video sources
Example: Video MainVideoSource: 1
Video DefaultPresentationSource: <1..5>
The Time zone setting
Define which video input source shall be used as the default presentation source (e.g. when you press the
Presentation key on the remote control). The input source is configured to a video input connector. See
the Video Input Matrix table at the back of the codec and the description of the Video Input Matrix in the
Interfaces section.
Time Zone: <S: 0, 100>
Specifies the NTP time zone where the system is located. See a list of the valid NTP Time Zone expressions
in the Appendices section.
Range: 1-5 presentation sources
Example: Video DefaultPresentationSource: 3
Format: String with a maximum of 100 characters.
Example: Time Zone: “Etc./UTC”
Video Monitors: <Single/Dual>
The codec can be used with more than one monitor and this setting lets you set the codec’s monitor layout
mode to Single or Dual. The dual output is provided on HDMI output 3.
Single: The same layout is shown on all monitors.
Dual: The layout is distributed on two monitors.
Example: Video Monitors: Single
D14129.02—NOVEMBER 2008
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
The settings library
Contents
Introduction
Getting started
About the menus
About the settings
Cameras
Appendices
Contact us
Video OSD Mode: <On/Off>
The Video OSD (On Screen Display) Mode lets you define whether or not information and icons on screen
should be displayed.
Video Input Source 2 Connector: <HDMI/HDSDI/YPbPr>
Select which video input connector to be active on connector group 2
HDMI: Select HDMI when you want to use the HDMI 2 connector as input
HDSDI: Select HD-SDI when you want to use the HD-SDI 2 connector as input
On: Set to On to display the on screen menus, icons and indicators (microphone on/off, encryption on/off).
Off: Set to Off to hide the on screen menus, icons and indicators (microphone on/off, encryption on/off).
YPbPr: Select YPbPr when you want to use the Y-Pb-Pr (Component) 2 connectors as input
Example: Video OSD Mode: On
Example: Video Input Source 2 Connector: HDMI
Video OSD Output: <1..4>
The Video OSD (On Screen Display) Output lets you define which monitor should display the on screen
menus, information and icons.
Video Input Source 3 Connector: <HDMI/HDSDI/DVI>
Select which video input connector to be active on connector group 3
HDMI: Select HDMI when you want to use the HDMI 3 connector as input
HDSDI: Select HD-SDI when you want to use the HD-SDI 3 connector as input
DVI: Select DVI-I when you want to use the DVI-I 3 connector as input
Range: Monitor 1-4
Example: Video OSD Output: 1
Example: Video Input Source 3 Connector: DVI
Video Input Source [1..5] CameraControl Mode: <On/Off>
Determines whether or not the camera control should be enabled for the specific video input source.
Addresses the specific video input source.
Video Input Source 4 Connector: <HDMI/HDSDI>
Select which video input connector to be active on connector group 4
HDMI: Select HDMI when you want to use the HDMI 4 connector as input
HDSDI: Select HD-SDI when you want to use the HD-SDI 4 connector as input
On: Set to On to enable camera control for the camera connected to the selected video input connector.
Off: Set to Off to disable camera control for the camera connected to the selected video input connector.
Example: Video Input Source 1 CameraControl Mode: On
Example: Video Input Source 4 Connector: HDMI
Video Input Source [1..5] CameraControl CameraId: <1..5>
Select the ID of the camera in the Visca chain that is connected to this camera source. The CameraId
setting represents the camera’s position in the Visca chain. Addresses the specific video input source.
Video Input Source 5 Connector: <YC/Composite/DVI>
Select which video input connector to be active on connector group 5
YC: Select YC when you want to use the S-Video (YC) input. Connect the S-Video input to the connector
marked as Y/Comp and C. NOTE! This configuration is not supported in version 1.
Cascaded cameras and Visca commands are described in the PrecisionHD 1080p User Guide. The user
Composite: Select Comp when you want to use the Composite input. Connect the Composite input to the
connector marked as Y/Comp NOTE! This configuration is not supported in version 1.
Example: Video Input Source 1 CameraControl CameraId: 1
DVI: Select DVI-I when you want to use the DVI-I 5 connector as input.
Video Input Source [1..5] Name: <S: 0, 50>
Customizable name of the connector group. Enter the name of the video input source 1-5.
Example: Video Input Source 5 Connector: DVI
Format: String with a maximum of 50 characters.
Video Input Source [1..5] Quality: <Motion/Sharpness>
Example: Video Input Source 1 Name: “”
When encoding and transmitting video there will be a tradeoff between high resolution and high framerate.
For some video sources it is more important to transmit high framerate than high resolution and vice versa.
The Quality setting specifies whether to give priority to high frame rate or to high resolution for a given
source. Addresses the selected video input connector.
Video Input Source 1 Connector: <HDMI/HDSDI/YPbPr>
Select which video input connector to be active on connector group 1
HDMI: Select HDMI when you want to use the HDMI 1 connector as input
HDSDI: Select HD-SDI when you want to use the HD-SDI 1 connector as input
YPbPr: Select YPbPr when you want to use the Y-Pb-Pr (Component) 1 connectors as input
Motion: Gives the highest possible framerate. Used when there is a need for higher frame rates, typically
when a large number of participants are present or when there is a lot of motion in the picture.
Sharpness: Gives the highest possible resolution. Used when you want the highest quality of detailed
images and graphics.
Example: Video Input Source 1 Connector: HDMI
Example: Video Input Source 1 HDMI 1 Quality: Motion
D14129.02—NOVEMBER 2008
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
The settings library
Contents
Introduction
Getting started
About the menus
About the settings
Cameras
Appendices
Contact us
Video Output HDMI [1, 3] Resolution: <640_480_60/800_600_60/1024_768_60/1280_1024_
60/1280_720_60/1920_1080_60/1280_768_60/1360_768_60/1366_768_60>
The Experimental menu
The Advanced configurations menu has an option called Experimental. The settings within this menu can be
used ‘as is’ and will not be documented.
Select the preferred resolution for the monitor connected to video output HDMI 1 or 3. This will force the
selected resolution on the monitor.
Note! The Experimental menu WILL change.
Range: 640x480@60p, 800x600@60p, 1024x768@60p, 1280x1024@60p, 1280x720@60p,
1920x1080@60p, 1280x768@60p, 1360x768@60p, 1366x768@60p
We recommend you visit the TANDBERG web site regularly for updated versions of the manual.
Example: Video Output HDMI 1 Resolution: 1920_1080_60
Video Output DVI [2, 4] Resolution: <640_480_60/800_600_60/1024_768_60/1280_1024_6
0/1280_720_60/1920_1080_60/1280_768_60/1360_768_60/1366_768_60>
Select the preferred resolution for the monitor connected to video output DVI-I 2 or 4. This will force the
selected resolution on the monitor.
Range: 640x480@60p, 800x600@60p, 1024x768@60p, 1280x1024@60p, 1280x720@60p,
1920x1080@60p, 1280x768@60p, 1360x768@60p, 1366x768@60p
Example: Video Output DVI 2 Resolution: 1920_1080_60
Video Output Composite [5] Resolution: <PAL/NTSC>
Select the preferred resolution for the monitor connected to video output composite 1. This will force the
selected resolution on the monitor.
Range: PAL, NTSC
Example: Video Output Composite 5 Resolution: NTSC
D14129.02—NOVEMBER 2008
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Cameras
Contents
Introduction
Getting started
About the menus
About the settings
Settings Library
Appendices
Contact us
Chapter 6
Cameras
Your TANDBERG PrecisionHD 1080p
Camera has been designed to give you
many years of safe, reliable operation.
In this chapter...
The PrecisionHD 1080p camera
Connecting the camera
Best view—Face recognition
Video output formats
Additional information about the camera
is found in the TANDBERG PrecisionHD
1080p User Guide.
Cameras in daisy chain
D14129.02—NOVEMBER 2008
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Cameras
Contents
Introduction
Getting started
About the menus
About the settings
Settings Library
Appendices
Contact us
The PrecisionHD 1080p camera
Video out (HDMI, HD-SDI). For video signals, connect from the
video out on the camera to the video in on the codec.
The orange LED illuminates while in a
call and flickers when there is an
incoming call.
Power and camera control. For power in and camera control,
connect from the camera control & power on the camera to
the Camera port on the codec. When the camera is used with
TANDBERG codecs power will be supplied through Camera Control
cable. When used with non-TANDBERG Codecs, you may have to
connect power separately.
The lens hood is detachable.
We recommend that you
mount it to prevent stray light
from disturbing your video
experience.
HDMI and HD-SDI
Just snap it on gently.
•
•
•
HDMI is the main source for video out when connected to Codec
C90. Maximum resolution is 1080p60.
HD-SDI is the secondary source for video. Maximum resolution
is 1080p30.
The HDMI and HD-SDI can be used simultaneously. The
maximum resolution is then 1080p30 if you want both to run with
the same resolution.
Th
green
is continuo
Kensington lock
The Kensington lock may be used to prevent the camera to be
moved from its place or to prevent theft.
illuminated when
is On, but it flickers
receiving signals fr
the remote control.
Cascaded cameras
The sockets named Extra Camera Out and Power In are used when
connecting cameras in daisy chain.
•
The first camera in the chain is powered up by the camera
control cable. The next cameras must use the 12V DC Power in.
HDMI and HD-SDI can be
used simultaneously.
•
The daisy chained cameras are connected by using an extra
camera cable between the Extra Camera sockets.
Kensington lock
Not Used
Power Supply
Camera Control
HDMI Video Out
See the TANDBERG PrecisionHD 1080p User Guide for
comprehensive information about the camera.
Extra Camera Out and for Daisy Chaining
HD-SDI Out
D14129.02—NOVEMBER 2008
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Cameras
Contents
Introduction
Getting started
About the menus
About the settings
Settings Library
Appendices
Contact us
Connecting the camera
The HDMI and HD-SDI can be used
simultaneously.
HDMI cable
The HDMI cable delivered with the camera is
5 meters.
Maximum length is 15 meter with a category 2
certified good quality HDMI cable.
HD-SDI cable
HD-SDI socket
The HD-SDI cable must be purchased
separately. The maximum recommendable
length of HD SDI cable is 100m.
HDMI to DVI-D adapter
The HDMI to DVI-D adapter is used when
connecting to a TANDBERG MXP codec or
TANDBERG Video Switch
HDMI and HD-SDI
can be used simultaneously.
Power supply connection
is NOT needed when the
camera is used with a
TANDBERG Codec.
Connect the camera control cable, RJ45 to RS-232.
Visca™ protocol is supported.
Connecting HDMI HD Video out on camera to HDMI 1 In on the Codec.
If you need to connect the camera to a TANDBERG Video Switch or to a system with a DVI-D socket, use
the enclosed HDMI to DVI-D adapter.
VISCA™ is a trademark of Sony Corporation
D14129.02—NOVEMBER 2008
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Cameras
Contents
Introduction
Getting started
About the menus
About the settings
Settings Library
Appendices
Contact us
Best view—Face recognition
This camera is capable of face recognition when used with
TANDBERG C90 Codecs. Consequently, the functionality is subject
to change without further notice in order to take advantage of further
developments.
NOTE: Observe that the Best view feature is still a preview feature.
The face recognition system aims to search for faces in order to
optimize the picture frame, hence the name Best view. Once a face
or group of faces has been detected camera zoom and camera angle
will be changed accordingly to obtain an optimal presentation on the
screen.
Kindly observe the following:
•
•
The Best view optimization process may take up to 5 seconds.
The detection of faces works better when people look towards the
camera.
•
•
The area from the eyebrows down to just below the lips should be
uncovered.
Best view (beta)
Exit
Beard is normally not a problem.
Press the corresponding
Soft key to start the Best
view optimization process.
Using Best view
Note that Best view works with TANDBERG C90 Codecs only!
The Best view feature is found
in the Camera control menu.
1. Press the
Layout key on the remote control to display the
Layout menu. Select Selfview to be shown as required.
2. Press the
Home key on the remote control to display the
Home menu and select Camera control
3. In the Camera control menu, locate the Best view button at the
bottom of the screen.
4. Press the corresponding Soft key on the remote control to start
the Best view optimization process. Look towards the camera for
about five seconds.
5. The system will now look for human faces and adjust the zoom
and camera angle to obtain a best fit.
D14129.02—NOVEMBER 2008
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Cameras
Contents
Introduction
Getting started
About the menus
About the settings
Settings Library
Appendices
Contact us
Video output formats
This section describes the video output formats for the TANDBERG
PrecisionHD 1080p camera.
DIP switch settings for video output formats
The video output format for the camera is set by DIP switches. The
DIP switches are found on the bottom side of the camera.
DIP Switch table for video formats
1
0
1
2
3
4
5
HDMI
HD-SDI
The default setting is Auto. When using HDMI, the video output format
is automatically detected. See the table to the right.
0
0
0
0
0
Auto
Maximum resolution for HDMI is 1080p60.
Maximum resolution for HD-SDI is 1080p30.
The DIP switch
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
0
0
0
1
1
1
1
0
0
0
1
1
0
0
1
1
0
0
1
0
1
0
1
0
1
0
1
1920x1080p25
1920x1080p30
1920x1080p50
1920x1080p60
1280x720p25
1280x720p30
1280x720p50
1280x720p60
1920x1080p25
1920x1080p30
1280x720p50
1280x720p60
1280x720p25
1280x720p30
1280x720p50
1280x720p60
Line voltage frequency
The camera will automatically detect the line voltage frequency when it
is 50 or 60Hz. You may set the video output format to a specific value
(use the DIP switches) to override the auto frequency detection, if a
different line voltage frequency is an issue.
Software control
The table shows the different settings available for the HDMI and
the HD-SDI outputs.
Bottom side of the TANDBERG
PrecisionHD 1080p camera
Auto: Camera negotiates format over HDMI. HD-SDI tracks HDMI
and defaults to 1080p30 in absence of HDMI sync.
Software: For more on the Software control setting, read about
video mode selections in the TANDBERG PrecisionHD 1080p User
Guide.
D14129.02—NOVEMBER 2008
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Cameras
Contents
Introduction
Getting started
About the menus
About the settings
Settings Library
Appendices
Contact us
Cameras in daisy chain
Example. Four daisy chained TANDBERG PrecisionHD 1080p cameras.
A single daisy chain can have up to seven cameras.
Power in
12V DC
Power in
12V DC
Power in
12V DC
Cascaded cameras
The sockets named Extra Camera and Power In
are used when connecting cameras in daisy chain.
Main
camera
Second
camera
Third
camera
Fourth
camera
•
HDMI and HD-SDI. The HDMI and HD-SDI can
be used simultaneously on the same camera.
•
Power. The first camera in the chain is powered
up from the codec by the VISCA camera control
cable. Additional cameras must use the 12V DC
Power in.
•
Extra camera cable. The daisy chained
cameras are connected by using the VISCA
Extra Camera cable between the Extra Camera
In and Codec Control In sockets
RJ11–RJ45
RJ11–RJ45
RJ11–RJ45
Connect to the
Camera Control
socket on the
Connect to the
Video Input 1
on the codec
Connect to the
Video Input 2
on the codec
Connect to the
Video Input 3
on the codec
Connect to the
Video Input 4
on the codec
Codec. When used
with TANDBERG
Codecs, this first
camera will need
no power supply
connected.
VISCA™ is a trademark of Sony Corporation
D14129.02—NOVEMBER 2008
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Appendices
Contents
Introduction
Getting started
About the menus
About the settings
Settings Library
Cameras
Contact us
Chapter 7
Appendices
In this chapter...
General room guidelines
Executive meeting room setup
High end meeting room setup
Video input matrix
Software upgrade
Upload certificates
XML files
Log files
NTP Time Zone expression
Supported RFCs in SIP
Remote Control TRC5
Remote Control key map
PrecisionHD camera
CE Declaration
China RoHS
Codec C90 dimensions
PrescisionHD 1080p dim.
PrescisionHD dimensions
Technical specifications
D14129.02—NOVEMBER 2008
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Contents
Introduction
Getting started
About the menus
About the settings
Settings Library
Cameras
Appendices
Contact us
The room equipment
When placing and using the room equipment there are a few
recommendations and guidelines to consider.
Environmental considerations
This section explains how to carry out basic adjustments and simple
tests to ensure that you send and receive the best possible image and
audio quality when using your system.
General room guidelines
The physical conditions
When building a video meeting room, or using an existing room for
video meetings there are a few guidelines to consider.
The microphone
Iris control and lighting
•
The microphones should be evenly distributed on the table. Avoid
positions where they can be hidden behind obstacles like laptop,
projector or other equipment placed on the table
By default the system camera will use an automatic iris to compensate
for changes in lighting. In addition to this feature, you may further
assist the system to maintain the best possible image quality by
paying special attention to environmental lighting and background
colors as described below.
Lighting
•
Do not place a microphone close to power outlets or similar
arrangements on the table. The microphone will pick up noise from
these arrangements quite strongly
•
The illumination should be distributed evenly in the room to obtain
low contrast
Remember the system will send live images of both yourself and your
immediate surroundings.
•
The ideal light intensity is a little higher than in an ordinary meeting
room. Typically, the luminous intensity should be 800–1400Lux,
measured at the table with an incident light meter
The camera
•
Avoid direct sunlight on the subject matter i.e. yourself, the
background or onto the camera lens as this will create harsh
contrasts
•
The camera should be able to “see” all participants in the room.
Use the pan, tilt and zoom features to adjust the picture.
Seating area and table
•
•
Avoid placing the seatings in front of a window with natural
daylight, as this will make the faces of people very dark
•
•
The seating area and table should be non-shiny and non-patterned
The seating area should allow all participants to see the monitor
The PC
If light levels are too low you may need to consider using artificial
lighting. As described above, direct illumination of the subject
matter and camera lens should be avoided
•
PC’s placed on the table should not cover the microphones as this
will reduce the audio quality at the far end
Walls
•
•
•
When using artificial lighting, daylight type lamps will produce the
most effective results. Avoid colored lighting
•
The color of the wall should be in good contrast to skin tonality
Light blue is a complementary color to skin tonality, it gives a good
contrast and is commonly used
Position of the system
Indirect light from shaded sources or reflected light from pale walls
often produces excellent results
•
Position the video system in such a way that all participants
attending the meeting are visible to the far end.
•
Acoustically reflective surfaces (such as glass or concrete) should
be covered with curtains or sound treatment
Avoid harsh side lighting or strong light from above. Strong sunlight
from a window or skylight may put part or all of the subject matter
in shadow or cause silhouetting
•
If appropriate, the far end should be able to see people entering or
leaving the room
Audio
The document camera
•
The Noise Floor (the sum of all the noise sources) should be less
Loudspeaker volume
•
The document camera should be close to the chair person or a
designated controller of the document camera for ease of use
than 44 dBC
The audio system will use the Digital Natural Audio Module (DNAM)
which is integrated in the system. The volume of the audio is controlled
by the Volume key on the remote control.
•
The reverberation time should be 0,3 to 0,5 seconds
•
Make sure this person is visible on screen while carry out the task
Ventilation
Other peripherals
•
The requirements for ventilation may be a little higher than in an
•
Arrange all the peripherals so that the chair person can reach each
of them to point, change the display, DVD, and still be fully visible
on screen while carry out the task
ordinary meeting room. Consult the specifications for the monitor
for data about the energy consumption. The TANDBERG Codec
C90 together with the TANDBERG PrecisionHD 1080p camera
has the following specifications:
•
•
•
Max rating – 175 Watts
Normal operation – 110 Watts
Standby – 110 Watts
•
•
Keep in mind the Noise Floor (see Audio)
Velocity creates noise, therefore keep velocity of air low
D14129.02—NOVEMBER 2008
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Contents
Introduction
Getting started
About the menus
About the settings
Settings Library
Cameras
Appendices
Contact us
The audio quality
To keep the high quality audio, make sure there is
free sight to the speaker module
The best audio quality to all participants
•
•
There should be free sight between the ears
of the participants and the system speaker
module
Participant sitting too far away from the video
system may not have the same audio quality as
the others.
The line of free sight
Ear height
This participant may not have
the same audio quality as the
others
Speaker module
(DNAM)
The picture (TANDBERG T1) serves as an
illustration to exemplify the content.
Making eye contact
Natural communication
Making eye contact with the far end participants
will improve the natural communication between
the people
PrecisionHD
•
Adjust the camera view (using zoom in/out) to
allow the participants to be shown in full size
on screen, and to keep eye contact with each
other at the same eye level
1080p camera
The far end participants
•
If the participants are sitting too close to
the monitor the camera will “look down” at
the participants. This may not give a good
presentation of the participants at the far end.
Eye height
65” LCD
monitor
The picture (TANDBERG T1) serves as an
illustration to exemplify the content.
D14129.02—NOVEMBER 2008
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Contents
Introduction
Getting started
About the menus
About the settings
Settings Library
Cameras
Appendices
Contact us
Guidelines for the executive
meeting room
For executive meeting rooms and the executive office.
General recommendations for the room layout
Video system
To fully utilize the telepresence experience there are some guidelines
you should consider.
Camera view
- with max zoom
out
The distance between the table and the video system
•
If the monitor is a 65” full HD LCD display this requires 2–2,5 m /
78–98 inch distance to the table to allow all participants to see a
clear picture on screen
•
•
Make sure all participants are covered within the camera angle,
which at maximum zoom out is 72°
Microphones
Adjust the camera view (using zoom in/out) to allow the
participants to be shown in full size on screen, and to keep eye
contact with each other at the same eye level
1
4
7
.@
ghi
2
5
8
0
abc
jkl
def
mno
3
6
9
#
Remote
control
pqrs
tuv
wxyz
abc/123
•
•
The camera should capture all participants in the room
Adjust the camera view
If the participants are sitting too close to the monitor the camera
will “look down” at the participants. This may not give a good
presentation of the participants at the far end.
Press the Zoom +/– button
the remote control to adjust the
picture on screen.
on
Adjust the camera view to allow
the participants to be shown in
full size on screen, and to keep
eye contact with each other at the
same eye level.
The speaker module
•
There should be free sight between the system speaker module
and the ear of the participants.
The microphones
A light blue wall color gives
a good contrast to the skin
tonality.
•
•
The microphones should be evenly distributed on the table
Avoid positions where they can be hidden behind obstacles like
laptop or other equipment placed on the table
•
Do not place a microphone close to power outlets or similar
arrangements on the table. The microphone may pick up noise
from these arrangements quite strongly.
D14129.02—NOVEMBER 2008
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Contents
Introduction
Getting started
About the menus
About the settings
Settings Library
Cameras
Appendices
Contact us
Sharing a PC presentation
General recommendations for the executive meeting room and
executive office are described on the previous page.
Dual video stream
With dual video stream you can view two different live video streams
simultaneously, the main video and one additional source. This could
for example be both a PC presentation and the person who gives the
presentation.
Shows the PC presentation
and the participants
If one of the video systems does not support Dual Video Stream, no
second video stream will be established and the PC presentation will
be shown as the main video.
Sharing the presentation
1. Make sure the PC do not cover any of the microphones as this will
reduce the audio quality at the far end
2. Locate the DVI cable and connect the PC to the video system
3. When pressing the PC button ( ) on the remote control the
default presentation source is activated.
1
4
7
.@
ghi
2
5
8
0
abc
jkl
def
mno
3
6
9
#
pqrs
tuv
wxyz
abc/123
PC
The DVI/VGA input is compliant with VESA Extended Display
Identification Data (EDID) and will be able to notify the PC of the
supported output formats.
Troubleshooting if the presentation does not show
•
On most PC’s you must press a special key combination to switch
the PC image from the PC screen to the video screen
•
Make sure the connector used for PC presentation is configured as
the default presentation source.
Go to: Home > Administrator settings > Advanced
configurations > Video > DefaultPresentationSource (the
default value is 3, and corresponds to ...Video > Input > Source 3)
The screen layout
Press the Layout button
remote control to select a suitable
layout on screen.
on the
•
Make sure your PC is set to activate your VGA output
The default layout when showing
a PC presentation is designed to
allow the participants to keep eye
contact with each other during the
presentation.
Other presentation sources
You can also connect other presentation sources like:
•
•
DVD
Default layout with a wide signal in
from the PC (currently only supported
on digital input)
Default layout with a 4/3 signal in from
the PC.
Document camera
D14129.02—NOVEMBER 2008
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Contents
Introduction
Getting started
About the menus
About the settings
Settings Library
Cameras
Appendices
Contact us
Guidelines for the high end meeting
room
For high end team collaboration rooms, team meeting rooms and
showroom floor.
General recommendations for the room layout
To fully utilize the telepresence experience there are some guidelines
you should consider.
Video system
The distance between the table and the video system
•
If the monitor is a 65” full HD LCD display this requires 2–2,5 m /
78–98 inch distance to the table to allow all participants to see a
clear picture on screen
Camera view
•
•
Make sure all participants are covered within the camera angle,
which at maximum zoom out is 72°
- with max zoom
out
Microphones
Adjust the camera view (using zoom in/out) to allow the
participants to be shown in full size on screen, and to keep eye
contact with each other at the same eye level
Remote
control
•
•
The camera should capture all participants in the room
If the participants are sitting too close to the monitor the camera
will “look down” at the participants. This may not give a good
presentation of the participants at the far end.
The speaker module
•
There should be free sight between the system speaker module
and the ear of the participants.
Adjust the camera view
The microphones
Press the Zoom +/– button
remote control to adjust the picture
on screen.
on the
•
•
The microphones should be evenly distributed on the table
Avoid positions where they can be hidden behind obstacles like
laptop or other equipment placed on the table
Adjust the camera view to allow the
participants to have eye contact with
each other at the same eye level.
•
Do not place a microphone close to power outlets or similar
arrangements on the table. The microphone may pick up noise
from these arrangements quite strongly.
D14129.02—NOVEMBER 2008
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Contents
Introduction
Getting started
About the menus
About the settings
Settings Library
Cameras
Appendices
Contact us
Sharing a PC presentation
General recommendations for high end team collaboration rooms,
team meeting rooms and showroom floor are described on the
previous page.
Shows the PC presentation
and the participants
Dual video stream
With dual video stream you can view two different live video streams
simultaneously, the main video and one additional source. This could
for example be both a PC presentation and the person who gives the
presentation.
If one of the video systems does not support Dual Video Stream, no
second video stream will be established and the PC presentation will
be shown as the main video.
Sharing the presentation
1. Make sure the PC do not cover any of the microphones as this will
reduce the audio quality at the far end
2. Locate the DVI cable and connect the PC to the video system
PC
3. When pressing the PC button ( ) on the remote control the
default presentation source is activated.
The DVI/VGA input is compliant with VESA Extended Display
Identification Data (EDID) and will be able to notify the PC of the
supported output formats.
Troubleshooting if the presentation does not show
•
On most PC’s you must press a special key combination to switch
the PC image from the PC screen to the video screen
•
Make sure the connector used for PC presentation is configured as
the default presentation source.
Go to: Home > Administrator settings > Advanced
configurations > Video > DefaultPresentationSource (the
default value is 3, and corresponds to ...Video > Input > Source 3)
The screen layout
Press the Layout button
remote control to select a suitable
layout on screen.
on the
•
Make sure your PC is set to activate your VGA output
The default layout when showing
a PC presentation is designed to
allow the participants to keep eye
contact with each other during the
presentation.
Other presentation sources
You can also connect other presentation sources like:
Default layout with a wide signal in
from the PC (currently only supported
on digital input)
Default layout with a 4/3 signal in from
the PC.
•
•
DVD
Document camera
D14129.02—NOVEMBER 2008
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Appendices
Contents
Introduction
Getting started
About the menus
About the settings
Settings Library
Cameras
Contact us
The Video Input Matrix
The video input matrix is found at the rear side of the codec and
illustrates the combinations in which the video inputs can be
connected.
Line in
Video input matrix
About the matrix
Input Sources
Connector Name
HDMI 1 HD-SDI 1 YPrPb 1
2nd Camera HDMI 2
Only one video input source from each row can be active at any time.
The numbers in the left column represents the Video Input Sources
1–5. The main connectors, which are used in basic setup, are marked
in orange color.
1
2
3
4
1st Camera
HD-SDI 2 YPrPb 2
HD-SDI 3 DVI-I 3
PC
HDMI 3
HDMI 4
The Comp. 5 and S-Video (YC) 5 inputs uses the same physical
connectors and can not be connected at the same time.
HD-SDI 4
–
5
DVI-I 5
Comp. 5* YC 5*
Configure the video inputs
You can configure the video input settings from the Administrator
Settings menu or by running API commands.
* Comp 5 and YC 5 are not supported in version 1
The default configurations are shown below:
What connectors are active is determined by the configuration of
the video input connector settings:
Administrator settings
Open the menu on screen to configure the video input sources
and which of the sources should be the main video source and
the default presentation source.
API commands
Open a telnet or ftp session to the codec to issue an API command to
configure the video input sources and which of the sources should be the
main video source and the default presentation source.
•
•
•
•
•
Video Input Source 1 Connector: HDMI
Video Input Source 2 Connector: HDMI
Video Input Source 3 Connector: DVI
Video Input Source 4 Connector: HDMI
Video Input Source 5 Connector: DVI
If the system is in standby mode, press any key on the remote
control to wake up the system.
The following commands determines which connector to be active:
• xconfiguration video input source 1 connector: hdmi
• xconfiguration video input source 2 connector: hdmi
• xconfiguration video input source 3 connector: dvi
• xconfiguration video input source 4 connector: hdmi
• xconfiguration video input source 5 connector: dvi
1. Select: Settings > Administrator Settings > Advanced
Configurations
The video name of the connector inputs should be set:
•
•
•
•
•
Video Input Source 1 Name: “Main Camera“
Video Input Source 2 Name: “Secondary Camera“
Video Input Source 3 Name: “PC“
2. From this point you can:
•
Search for the words “source” or “video” to see a list
of the available Video Input Source [1–5] Connector
settings
Video Input Source 4 Name: “DVD“
Set the video quality and a name of the video inputs 1 to 5:
Video Input Source 5 Name: “Document Camera“
•
- or, you can navigate down in the list to Video > Input >
Source 1 > Connector
• xconfiguration video input source 1 quality: motion
• xconfiguration video input source 1 name: “Main Camera“
The video quality of the connector inputs should be set:
3. On the remote control, press the right arrow to edit the
values
•
•
•
•
•
Video Input Source 1 Quality: Motion
Video Input Source 2 Quality: Motion
Video Input Source 3 Quality: Sharpness
Video Input Source 4 Quality: Motion
Video Input Source 5 Quality: Sharpness
•
Configure the video inputs 2 to 5
•
Select a value and press Save, or press Cancel to leave
without saving.
The main video source is the camera, connected to video input source 1:
4. Proceed and configure the:
• xconfiguration video mainvideosource: 1
•
•
•
•
Video Input Source Name, for the current input
Video Input Source Quality, for the current input
Video Main Video Source, for the system
The default presentation source is a PC, connected to video input source 3:
To determine the main video source and the default presentation
source for the system the following setting must be configured:
• xconfiguration video defaultpresentationsource: 3
•
•
Video MainVideoSource: 1
Video Default Presentation Source, for the system
Video DefaultPresentationSource: 3
D14129.02—NOVEMBER 2008
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Appendices
Contents
Introduction
Getting started
About the menus
About the settings
Settings Library
Cameras
Contact us
Software upgrade
The software upgrade procedure
Contact your TANDBERG representative to obtain the software upgrade file.
The Upgrade tab lets you select the software
upgrade file for TANDBERG Codec C90 and install
the new software.
Please follow the procedure described on this
page.
1. Open a web browser and enter the
IP address to connect to the Codec
C90 by HTTP
2. Select the Upgrade tab
3. Click Browse... and locate the
upgrade file (.PKG)
4. Click the Install software button to
start the installation.
5. Leave the system for a few minutes
to allow the installation process to
complete. The upgrade process
takes about 4–5 minutes.
D14129.02—NOVEMBER 2008
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Appendices
Contents
Introduction
Getting started
About the menus
About the settings
Settings Library
Cameras
Contact us
Upload certificates
The certificates upload procedure
Contact your system administrator to obtain the required files (.PEM format).
The Upload certificates tab lets you upload a CA list
(ROOT certificate) to authenticate TLS connections
on SIP and a HTTPS certificate to enable HTTPS.
The system administrator issues/obtains and installs
unique certificates to each system.
How to upload the certificate
For TLS connections a ROOT Certificate (CA-list) can
be uploaded from the web interface.
1. Open a web browser and enter the IP
address to connect to the Codec C90
by HTTP.
When the SIP setting TlsVerify is enabled, only TLS
connections to servers, whom x.509 certificate is
validated against the CA-list, will be allowed.
2. Select the Upload certificates tab
Go to: Settings > Administrator settings > Advanced
configuration > SIP > Profile > TlsVerify
3. Click Browse... and locate the
certificate files (.PEM)
To install a certificate, you need:
•
•
•
•
HTTPS certificate ( .PEM format)
ROOT certificate ( .PEM format)
Private key ( .PEM format)
Passphrase (optional)
4. Type in the Passphrase
5. Click the Upload button to start the
certificate installation.
D14129.02—NOVEMBER 2008
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Appendices
Contents
Introduction
Getting started
About the menus
About the settings
Settings Library
Cameras
Contact us
XML files
View XML files
The XML files tab gives a complete overview of the
status of the system and the commands available
on XML format.
Select the XML file to see a tree structure of all the configuration commands
Configuration
Configuration type commands defines the system
settings and are controlled from the Administrator
Settings menu or from the API. Configuration type
commands are either supplied or read by the user.
Example: Set IP addresses, default presentation
source, standby delay, and enabling/disabling of
various features etc.
The configuration commands are structured in
a hierarchy, making up a database of system
settings.
Status
Status type commands returns information about
the system and system processes and are issued
from the API. Status type commands are read by
the user.
Example: Information generated by the system
about ongoing calls, network status, conference
status etc.
All status information is structured in a hierarchy,
making up a database constantly being updated by
the system to reflect system and process changes.
Command
Command type commands instructs the system
to perform an action and are issued from the API.
Command type commands are supplied by the
user.
Example: instructing the system to place a call,
mute/unmute microphones, disconnect a call, etc.
A Command type command is usually followed by
a set of parameters to specify how the given action
is to be executed.
D14129.02—NOVEMBER 2008
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Appendices
Contents
Introduction
Getting started
About the menus
About the settings
Settings Library
Cameras
Contact us
Log files
Debug log files
Select a debug log file by clicking on the name of the file.
In the Logs tab you will find debug log files.
These are TANDBERG specific debug files which
may be required by TANDBERG in the need of
technical support.
Some of the log files can be opened or saved.
Some of the log files can be saved.
You will then see the following dialog
box:
D14129.02—NOVEMBER 2008
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Appendices
Contents
Introduction
Getting started
About the menus
About the settings
Settings Library
Cameras
Contact us
NTP Time Zone expressions
With reference to the Time zone setting in the Administrator settings menu, see the Settings library section.
Specifies the NTP time zone where the system is located.
Example 1: Time Zone: “America/New_York”
America/Cordoba
America/Costa_Rica
America/Cuiaba
America/Inuvik
America/Iqaluit
America/Jamaica
Example 2: Time Zone: “Etc/UTC”
America/Curacao
America/Danmarkshavn
America/Dawson
America/Dawson_Creek
America/Denver
America/Jujuy
America/Juneau
NOTE: Spelling correctly is important when entering the NTP Time Zone expression.
America/Kentucky
America/Kentucky/Louisville
America/Kentucky/Monticello
America/Knox_IN
Africa
Africa/Libreville
America/Argentina/Cordoba
America/Argentina/Jujuy
America/Argentina/La_Rioja
America/Argentina/Mendoza
America/Argentina/Rio_Gallegos
America/Argentina/San_Juan
America/Argentina/San_Luis
America/Argentina/Tucuman
America/Argentina/Ushuaia
America/Aruba
Africa/Abidjan
Africa/Accra
Africa/Lome
America/Detroit
Africa/Luanda
America/Dominica
America/Edmonton
America/Eirunepe
America/El_Salvador
America/Ensenada
America/Fort_Wayne
America/Fortaleza
America/Glace_Bay
America/Godthab
America/Goose_Bay
America/Grand_Turk
America/Grenada
America/Guadeloupe
America/Guatemala
America/Guayaquil
America/Guyana
America/La_Paz
Africa/Addis_Ababa
Africa/Algiers
Africa/Lubumbashi
Africa/Lusaka
America/Lima
America/Los_Angeles
America/Louisville
America/Maceio
Africa/Asmara
Africa/Asmera
Africa/Bamako
Africa/Bangui
Africa/Banjul
Africa/Malabo
Africa/Maputo
Africa/Maseru
America/Managua
America/Manaus
Africa/Mbabane
Africa/Mogadishu
Africa/Monrovia
America/Marigot
Africa/Bissau
America/Asuncion
America/Martinique
America/Mazatlan
America/Mendoza
America/Menominee
America/Merida
Africa/Blantyre
Africa/Brazzaville
Africa/Bujumbura
Africa/Cairo
Africa/Nairobi
America/Atikokan
Africa/Ndjamena
Africa/Niamey
America/Atka
America/Bahia
Africa/Nouakchott
Africa/Ouagadougou
Africa/Porto-Novo
Africa/Sao_Tome
Africa/Timbuktu
Africa/Tripoli
America/Barbados
Africa/Casablanca
Africa/Ceuta
America/Belem
America/Mexico_City
America/Miquelon
America/Moncton
America/Monterrey
America/Montevideo
America/Montreal
America/Montserrat
America/Nassau
America/Belize
Africa/Conakry
Africa/Dakar
America/Blanc-Sablon
America/Boa_Vista
America/Halifax
Africa/Dar_es_Salaam
Africa/Djibouti
Africa/Douala
Africa/El_Aaiun
Africa/Freetown
Africa/Gaborone
Africa/Harare
America/Bogota
America/Havana
Africa/Tunis
America/Boise
America/Hermosillo
America/Indiana
Africa/Windhoek
America
America/Buenos_Aires
America/Cambridge_Bay
America/Campo_Grande
America/Cancun
America/Indiana/Indianapolis
America/Indiana/Knox
America/Adak
America/New_York
America/Nipigon
America/Anchorage
America/Anguilla
America/Antigua
America/Araguaina
America/Argentina
America/Argentina/Buenos_Aires
America/Argentina/Catamarca
America/Argentina/ComodRivadavia
America/Indiana/Marengo
America/Indiana/Petersburg
America/Indiana/Tell_City
America/Indiana/Vevay
America/Caracas
America/Nome
Africa/Johannesburg
Africa/Kampala
Africa/Khartoum
Africa/Kigali
America/Catamarca
America/Cayenne
America/Noronha
America/North_Dakota
America/North_Dakota/Center
America/North_Dakota/New_Salem
America/Panama
America/Cayman
America/Indiana/Vincennes
America/Indiana/Winamac
America/Indianapolis
America/Chicago
Africa/Kinshasa
Africa/Lagos
America/Chihuahua
America/Coral_Harbour
D14129.02—NOVEMBER 2008
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Appendices
Contents
Introduction
Getting started
About the menus
About the settings
Settings Library
Cameras
Contact us
NTP Time Zone expressions, cont...
America/Pangnirtung
America/Paramaribo
America/Phoenix
America/Yellowknife
Antarctica
Asia/Dili
Asia/Dubai
Asia/Rangoon
Atlantic/South_Georgia
Atlantic/St_Helena
Atlantic/Stanley
Australia
Asia/Riyadh
Antarctica/Casey
Antarctica/Davis
Antarctica/DumontDUrville
Antarctica/Mawson
Antarctica/McMurdo
Antarctica/Palmer
Antarctica/Rothera
Antarctica/South_Pole
Antarctica/Syowa
Antarctica/Vostok
Arctic
Asia/Dushanbe
Asia/Gaza
Asia/Riyadh87
Asia/Riyadh88
Asia/Riyadh89
Asia/Saigon
America/Port_of_Spain
America/Port-au-Prince
America/Porto_Acre
America/Porto_Velho
America/Puerto_Rico
America/Rainy_River
America/Rankin_Inlet
America/Recife
Asia/Harbin
Australia/ACT
Asia/Ho_Chi_Minh
Asia/Hong_Kong
Asia/Hovd
Australia/Adelaide
Australia/Brisbane
Australia/Broken_Hill
Australia/Canberra
Australia/Currie
Australia/Darwin
Australia/Eucla
Australia/Hobart
Australia/LHI
Asia/Sakhalin
Asia/Samarkand
Asia/Seoul
Asia/Irkutsk
Asia/Istanbul
Asia/Jakarta
Asia/Shanghai
Asia/Singapore
Asia/Taipei
America/Regina
Asia/Jayapura
Asia/Jerusalem
Asia/Kabul
America/Resolute
America/Rio_Branco
America/Rosario
Asia/Tashkent
Asia/Tbilisi
Arctic/Longyearbyen
Asia
Asia/Kamchatka
Asia/Karachi
Asia/Kashgar
Asia/Katmandu
Asia/Kolkata
Asia/Krasnoyarsk
Asia/Kuala_Lumpur
Asia/Kuching
Asia/Kuwait
Asia/Tehran
Australia/Lindeman
Australia/Lord_Howe
Australia/Melbourne
Australia/North
Australia/NSW
America/Santiago
America/Santo_Domingo
America/Sao_Paulo
America/Scoresbysund
America/Shiprock
America/St_Barthelemy
America/St_Johns
America/St_Kitts
Asia/Aden
Asia/Tel_Aviv
Asia/Thimbu
Asia/Almaty
Asia/Amman
Asia/Thimphu
Asia/Tokyo
Asia/Anadyr
Asia/Aqtau
Asia/Ujung_Pandang
Asia/Ulan_Bator
Asia/Ulaanbaatar
Asia/Urumqi
Australia/Perth
Asia/Aqtobe
Australia/Queensland
Australia/South
Australia/Sydney
Australia/Tasmania
Australia/Victoria
Australia/West
Asia/Ashgabat
Asia/Ashkhabad
Asia/Baghdad
Asia/Bahrain
America/St_Lucia
America/St_Thomas
America/St_Vincent
America/Swift_Current
America/Tegucigalpa
America/Thule
Asia/Macao
Asia/Vientiane
Asia/Vladivostok
Asia/Yakutsk
Asia/Macau
Asia/Baku
Asia/Magadan
Asia/Makassar
Asia/Manila
Asia/Bangkok
Asia/Beirut
Asia/Yekaterinburg
Asia/Yerevan
Australia/Yancowinna
Brazil
Asia/Bishkek
Asia/Muscat
Atlantic
Brazil/Acre
America/Thunder_Bay
America/Tijuana
Asia/Brunei
Asia/Nicosia
Atlantic/Azores
Atlantic/Bermuda
Atlantic/Canary
Atlantic/Cape_Verde
Atlantic/Faeroe
Atlantic/Faroe
Atlantic/Jan_Mayen
Atlantic/Madeira
Atlantic/Reykjavik
Brazil/DeNoronha
Brazil/East
Asia/Calcutta
Asia/Choibalsan
Asia/Chongqing
Asia/Chungking
Asia/Colombo
Asia/Dacca
Asia/Novosibirsk
Asia/Omsk
America/Toronto
Brazil/West
America/Tortola
Asia/Oral
Canada
America/Vancouver
America/Virgin
Asia/Phnom_Penh
Asia/Pontianak
Asia/Pyongyang
Asia/Qatar
Canada/Atlantic
Canada/Central
Canada/Eastern
Canada/East-Saskatchewan
Canada/Mountain
America/Whitehorse
America/Winnipeg
America/Yakutat
Asia/Damascus
Asia/Dhaka
Asia/Qyzylorda
D14129.02—NOVEMBER 2008
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Appendices
Contents
Introduction
Getting started
About the menus
About the settings
Settings Library
Cameras
Contact us
NTP Time Zone expressions, cont...
Canada/Newfoundland
Canada/Pacific
Canada/Saskatchewan
Canada/Yukon
CET
Etc/GMT-2
Europe/Luxembourg
Europe/Madrid
Europe/Malta
Europe/Mariehamn
Europe/Minsk
Europe/Monaco
Europe/Moscow
Europe/Nicosia
Europe/Oslo
GMT+0
GMT0
Navajo
Pacific/Tarawa
Pacific/Tongatapu
Pacific/Truk
Pacific/Wake
Pacific/Wallis
Pacific/Yap
Poland
Etc/GMT-3
NZ
Etc/GMT-4
GMT-0
NZ-CHAT
Etc/GMT-5
Greenwich
Pacific
Etc/GMT-6
Hongkong
HST
Pacific/Apia
Chile
Etc/GMT-7
Pacific/Auckland
Pacific/Chatham
Pacific/Easter
Pacific/Efate
Chile/Continental
Chile/EasterIsland
CST6CDT
Etc/GMT-8
Iceland
Indian
Etc/GMT-9
Portugal
Etc/Greenwich
Etc/UCT
Indian/Antananarivo
Indian/Chagos
Indian/Christmas
Indian/Cocos
Indian/Comoro
Indian/Kerguelen
Indian/Mahe
Indian/Maldives
Indian/Mauritius
Indian/Mayotte
Indian/Reunion
Iran
posixrules
PRC
Cuba
Europe/Paris
Pacific/Enderbury
Pacific/Fakaofo
Pacific/Fiji
EET
Etc/Universal
Etc/UTC
Europe/Podgorica
Europe/Prague
Europe/Riga
PST8PDT
ROC
Egypt
Eire
Etc/Zulu
Pacific/Funafuti
Pacific/Galapagos
Pacific/Gambier
Pacific/Guadalcanal
Pacific/Guam
Pacific/Honolulu
Pacific/Johnston
Pacific/Kiritimati
Pacific/Kosrae
Pacific/Kwajalein
Pacific/Majuro
Pacific/Marquesas
Pacific/Midway
Pacific/Nauru
Pacific/Niue
ROK
EST
Europe
Europe/Rome
Europe/Samara
Europe/San_Marino
Europe/Sarajevo
Europe/Simferopol
Europe/Skopje
Europe/Sofia
Singapore
Turkey
EST5EDT
Europe/Amsterdam
Europe/Andorra
Europe/Athens
Europe/Belfast
Europe/Belgrade
Europe/Berlin
Europe/Bratislava
Europe/Brussels
Europe/Bucharest
Europe/Budapest
Europe/Chisinau
Europe/Copenhagen
Europe/Dublin
Europe/Gibraltar
Europe/Guernsey
Europe/Helsinki
Europe/Isle_of_Man
Europe/Istanbul
Europe/Jersey
Europe/Kaliningrad
Europe/Kiev
Etc
UCT
Etc/GMT
Universal
US
Etc/GMT+0
Etc/GMT+1
Etc/GMT+10
Etc/GMT+11
Etc/GMT+12
Etc/GMT+2
Etc/GMT+3
Etc/GMT+4
Etc/GMT+5
Etc/GMT+6
Etc/GMT+7
Etc/GMT+8
Etc/GMT+9
Etc/GMT0
Etc/GMT-0
Etc/GMT-1
Etc/GMT-10
Etc/GMT-11
Etc/GMT-12
Etc/GMT-13
Etc/GMT-14
US/Alaska
US/Aleutian
US/Arizona
US/Central
US/Eastern
US/East-Indiana
US/Hawaii
US/Indiana-Starke
US/Michigan
US/Mountain
US/Pacific
US/Pacific-New
US/Samoa
UTC
Europe/Stockholm
Europe/Tallinn
Europe/Tirane
Europe/Tiraspol
Europe/Uzhgorod
Europe/Vaduz
Europe/Vatican
Europe/Vienna
Europe/Vilnius
Europe/Volgograd
Europe/Warsaw
Europe/Zagreb
Europe/Zaporozhye
Europe/Zurich
Factory
iso3166.tab
Israel
Jamaica
Japan
Kwajalein
Libya
localtime
MET
Pacific/Norfolk
Pacific/Noumea
Pacific/Pago_Pago
Pacific/Palau
Mexico
Mexico/BajaNorte
Mexico/BajaSur
Mexico/General
Mideast
Pacific/Pitcairn
Pacific/Ponape
Pacific/Port_Moresby
Pacific/Rarotonga
Pacific/Saipan
Pacific/Samoa
Pacific/Tahiti
WET
Mideast/Riyadh87
Mideast/Riyadh88
Mideast/Riyadh89
MST
W-SU
zone.tab
Europe/Lisbon
Europe/Ljubljana
Europe/London
GB
Zulu
GB-Eire
GMT
MST7MDT
D14129.02—NOVEMBER 2008
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Appendices
Contents
Introduction
Getting started
About the menus
About the settings
Settings Library
Cameras
Contact us
•
•
•
•
•
•
•
•
•
•
•
RFC 4574 The Session Description Protocol (SDP) Label Attribute
RFC 4582 The Binary Floor Control Protocol
RFC 4585 Extended RTP Profile for RTCP-Based Feedback
RFC 4587 RTP Payload Format for H.261 Video Streams
RFC 4629 RTP Payload Format for ITU-T Rec. H.263 Video
RFC 5168 XML Schema for Media Control
Current RFCs and drafts supported in SIP
Supported RFCs in SIP
•
•
•
•
•
RFC 1889 RTP: A Transport Protocol for Real-time Applications
RFC 2190 RTP Payload Format for H.263 Video Streams
RFC 2327 SDP: Session Description Protocol
The RFC (Request for Comments) series contains technical and
organizational documents about the Internet, including the technical
specifications and policy documents produced by the Internet
Engineering Task Force (IETF).
RFC 2396 Uniform Resource Identifiers (URI): Generic Syntax
RFC 2429 RTP Payload Format for the 1998 Version of ITU-T Rec.
H.263 Video (H.263+)
RFC 4796 The SDP Content Attribute
•
•
RFC 2617 Digest Authentication
RFC 4583 SDP Format for BFCP Streams
RFC 2782 DNS RR for specifying the location of services (DNS
SRV)
draft-ietf-sipping-cc-transfer-06.txt
draft-ietf-avt-rtp-h264-rcdo-01.txt
•
RFC 2833 RTP Payload for DTMF Digits, Telephony Tones and
Telephony Signals
draft-ietf-avt-rtp-h264-params-01.txt
•
•
•
RFC 2976 The SIP INFO Method
RFC 3016 RTP Payload Format for MPEG-4 Audio/Visual Streams
Media capabilities supported in SIP
The audio and video media capabilities supported in SIP are the same
as for H.323.
RFC 3047 RTP Payload Format for ITU-T Recommendation
G.722.1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
RFC 3261 SIP: Session Initiation Protocol
RFC 3262 Reliability of Provisional Responses in SIP
RFC 3263 Locating SIP Servers
RFC 3264 An Offer/Answer Model with SDP
RFC 3311 UPDATE method
RFC 3361 DHCP Option for SIP Servers
RFC 3420 Internet Media Type message/sipfrag
RFC 3515 Refer method
RFC 3550 RTP: A Transport Protocol for Real-Time Applications
RFC 3581 Symmetric Response Routing
RFC 3605 RTCP attribute in SDP
RFC 3711 The Secure Real-time Transport Protocol (SRTP)
RFC 3840 Indicating User Agent Capabilities in SIP
RFC 3890 A Transport Independent Bandwidth Modifier for SDP
RFC 3891 The SIP “Replaces” Header
RFC 3892 Referred-By Mechanism
RFC 3960 Early Media
RFC 3984 RTP Payload Format for H.264 Video
RFC 4028 Session Timers in SIP
RFC 4145 TCP-Based Media Transport in the SDP
RFC 4568 SDP:Security Descriptions for Media Streams
D14129.02—NOVEMBER 2008
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Appendices
Contents
Introduction
Getting started
About the menus
About the settings
Settings Library
Cameras
Contact us
TANDBERG Remote Control TRC5
Function keys: Represents shortcuts and advanced
functions. Each key reflects a soft key on screen.
Presentation: Press the
key to show/hide a presentation.
key to zoom the camera in
Microphone: Press the
key to toggle the microphones on/off.
Zoom: Press the + or – on the
and out.
Volume: Press the + or – on the
key to adjust the codec
volume.
Arrows:
•
•
•
Up/Down: Use the and arrow keys to navigate in the
menu.
OK/Select: Press the
Phone book: Press the
Home: Press the
key to confirm your choice or selection.
key to display the local Phone book.
key to key to show the menu on screen.
Arrow Right: Press the arrow key to expand the selected
menu item or to move to the right in a text field.
Arrow Left: Press the arrow key to go one step back in
the menu or to move to the left in a text field.
Layout: Press the
key to display the Layout menu, then
select a view in the menu.
Call: Using the
key:
1.@
4 ghi
2 abc
5 jkl
8 tuv
0
def 3
mno 6
wxyz 9
INITIATE A CALL: Select a name from the Phone book or enter the
name, number or URI and press the Call key to initiate the call.
End call/Standby: Press the
idle, press and hold the key to go into standby mode.
key to end a call, or when
SHORTCUT TO RECENT CALLS: Use the Call key as a shortcut to
Recent Calls when the Call menu is not visible.
7 pqrs
Alphanumeric keypad: Use the keypad in the same way as you
would use a cellular phone.
Clear: Press the key to remove characters in a text field.
abc/123
#
•
0-9, a-z, period (.), @, space, *: Press a key repeatedly to
toggle between the options displayed on each key.
•
abc/123 #: Press the # key to toggle between touch tones
mode (long press), lower case characters and numbers.
Waking up the system
IR transmitter range (DIP switch setting)
Grab the remote control and make sure your hand
touches the rubber line sensors going along both
sides of the remote control.
The IR transmitter has a short and long range. Open the battery
cover and remove the batteries to set the DIP switch.
•
•
Short range (1 m): Move the DIP switch down.
Longer range: Move the DIP switch up.
or: Touch any key on the remote control.
D14129.02—NOVEMBER 2008
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Appendices
Contents
Introduction
Getting started
About the menus
About the settings
Settings Library
Cameras
Contact us
TANDBERG Remote
Button codes - Remote control TRC5
Button codes - Remote control TRC5
IR Signal parameters
Control TRC5 key map
Dec
0
Hex
0
Address
Button name
Dec
33
34
35
36
37
38
39
–
Hex
21
22
23
24
25
26
27
–
Address
Button name
Ok
Name
Description
The TANDBERG Remote control TRC5 has the
following button codes and IR signal parameters.
0
0
0
0
0
0
Protocol
1
1
0
Number 1
Call
Reference frequency
End call
Phone book
Layout
2
2
0
0
0
0
0
0
0
0
0
0
0
Number 2
Number 3
Number 4
Number 5
Number 6
Number 7
Number 8
Number 9
Number 0
*
Address
3
3
IR wavelength
IR carrier frequency
4
4
Clear
5
5
6
6
7
7
41
42
43
44
45
46
–
29
2A
2B
2C
2D
2E
–
8
8
0
0
0
0
0
Soft key 1
Soft key 2
Soft key 3
Soft key 4
Soft key 5
9
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
20
#
–
–
–
–
–
–
0
Presenter
51
33
0
Home
0
0
Zoom out
Zoom in
0
0
0
Volume down
Volume up
Microphone off
0
0
0
0
Arrow up
Arrow down
Arrow left
Arrow right
D14129.02—NOVEMBER 2008
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Appendices
Contents
Introduction
Getting started
About the menus
About the settings
Settings Library
Cameras
Contact us
The PrecisionHD camera
This page describes the TANDBERG PrecisionHD camera, which was
the first TANDBERG HD camera.
Connecting the camera
Video out. For video out signals, connect from the HDMI on the
camera to a HDMI video input on the codec.
Power and camera control. For power in and camera control,
connect from the camera control & power on the camera to the
Camera port on the codec.
HDMI
•
HDMI is the main source for video out when connected to a Codec
C90. Maximum resolution is 1280x720p30
•
This output does not support HDCP (High Bandwidth Digital
Content Protection).
Cascaded cameras
VISCA
Daisy
chain
Power in
12 V DC
HDMI
video
out
Camera
control &
Power
Kensington
lock
The sockets named Extra Camera and Power In are used when
connecting cameras in daisy chain.
•
The first camera in the chain is powered up by the camera control
cable. The next cameras must use the 12V DC Power in.
Pin-out—VISCA Daisy chain
•
The daisy chained cameras are connected by using an extra
camera cable (maximum length ## m) between the Extra Camera
sockets.
Pin-out—VISCA camera control
Pin-out—TANDBERG camera cable
RJ45 (8 pin) to D-SUB
RJ 6 pins modular jack
Signal name
RJ 8 pins shielded modular jack
Pin
Pin
Signal name
Signal
name
RJ45
pin
D-SUB
pin
6
GND
8
+12V (presence 2.8mA current
source when connected in daisy
chain)
Kensington lock
5
4
3
2
1
GND
+12V DC
GND
RX
1
2
3
6
4
5
7
8
Twisted
pair
4
5
2
3
1
6
5
4
The Kensington lock may be used to prevent the camera to be moved
from its place or to prevent theft.
RXD (in)
7
6
5
4
3
2
1
GND
TXD (out)
Twisted
pair
TXD (out)
NC (no connect)
NC (no connect)
RXD (in)
Presence (12V in daisy chain)
GND
TX
NC
Twisted
pair
NC
GND
+12V DC
Twisted
pair
GND
+12V
D14129.02—NOVEMBER 2008
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Appendices
Contents
Introduction
Getting started
About the menus
About the settings
Settings Library
Cameras
Contact us
CE Declaration for Codec C90
For an official, signed version of this document, or details regarding documentation from
the technical construction file, please contact TANDBERG.
EC Declaration of conformity
MANUFACTURER:
PRODUCT NAME:
TYPE NUMBER:
DESCRIPTION:
TANDBERG Telecom AS
TANDBERG Codec C90
TTC6-09
Video Conferencing Equipment
DIRECTIVES:
LVD 2006/95/EC
This equipment complies with.
EMC 2004/108/EC
HARMONIZED STANDARDS:
EN 60950-1:2001, A11:2004
EN 55022 (2006)
Applied in order to verify compliance with
directives.
EN 55024 (1998) + A1 (2001) + A2 (2003)
EN 61000-3-2 (2006)
EN 61000-3-3 (1995) + A1 (2001) + A2 (2005)
TEST REPORTS and
Reports:
Certificates No.:
106684
CERTIFICATES ISSUED BY:
LVD (Nemko AS)
EMC (Nemko AS)
E08517.00
TECHNICAL CONSTRUCTION FILE NO.:
X14347
2008
YEAR WHICH THE CE-MARK WAS AFFIXED:
D14129.02—NOVEMBER 2008
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Appendices
Contents
Introduction
Getting started
About the menus
About the settings
Settings Library
Cameras
Contact us
China RoHS table
This product complies with the Chineese RoHS.
D14129.02—NOVEMBER 2008
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Appendices
Contents
Introduction
Getting started
About the menus
About the settings
Settings Library
Cameras
Contact us
TANDBERG Codec C90 dimensions
The TANDBERG Codec C90 dimensions in mm.
Front view
Left side view
32,0
465,0
486,0
442,0
Top view
D14129.02—NOVEMBER 2008
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Appendices
Contents
Introduction
Getting started
About the menus
About the settings
Settings Library
Cameras
Contact us
PrecisionHD 1080p camera dimensions
142,0
4,4
105,0
148,1
105,9 (eye centre)
20,5
32,2
62,4
2,5
2,5
220,0
125,4
190,0
ø
79,6
63,0
14,0
114,6
34,5
106,3°
191,0
ø
82,0
D14129.02—NOVEMBER 2008
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Appendices
Contents
Introduction
Getting started
About the menus
About the settings
Settings Library
Cameras
Contact us
•
•
1280x720@30 fps (720p30)
1280x720@25 fps (720p25)
•
•
•
•
•
1280x768@60fps (WXGA)
1024x768@60fps (XGA)
1280x1024@60fps (SXGA)
640x480@60fps (VGA)
800x600@60fps (SVGA)
set for balanced line level
Technical specifications
•
•
2 x RCA/Phono, Line Level: Stereo PC input
2 x RCA/Phono, Line Level: Stereo auxiliary/
DVD input
2 x DVI-I inputs, supported formats:
UNIT DELIVERED COMPLETE WITH:
•
2 x HDMI, digital: Stereo PC/DVD inputs
Analog (VGA):
Video conferencing codec, remote control,
rack mounting rails, LAN cable, power cable
•
•
•
•
•
•
•
•
•
•
•
•
•
1024x768@60, 70, 75, 85 fps (XGA)
1280x1024@60, 75 fps (SXGA)
Digital (DVI-D):
AUDIO OUTPUTS (8 OUTPUTS)
1 x COMPOSITE OUTPUT (BNC CONNECTOR),
supported formats:
•
•
2 x XLR, balanced line level, stereo main audio
BANDWIDTH
2 x RCA/Phono, line level, stereo main audio,
configurable to S/PDIF
•
PAL/NTSC
•
•
H.323/SIP up to 6 Mbps point-to-point
Up to 10 Mbps total MultiSite bandwidth
1920x1080@60 fps (1080p60)
1920x1080@50 fps (1080p50)
1920x1080@30 fps (1080p30)
1920x1080@25 fps (1080p25)
1280x720@60 fps (720p60)
1280x720@50 fps (720p50)
640x480@60 fps (480p60)
800x600@60 fps (SVGA)
•
2 x RCA/Phono, line level, stereo to recording
device
VESA Monitor Power Management
FIREWALL TRAVERSAL
•
•
1 x HDMI, digital, stereo main audio
LIVE VIDEO RESOLUTIONS (ENCODE/DECODE)
•
•
TANDBERG Expressway™ Technology
H.460.18, H.460.19 Firewall Traversal
1 x HDMI, digital, stereo to recording device
•
•
•
•
•
•
•
•
•
•
•
•
•
176x144@30fps (QCIF)
352x288@30fps (CIF)
DUAL STREAM
VIDEO STANDARDS
H.261, H.263, H.263+, H.264
512x288@30fps (w288p)
576x448@30fps (448p)
768x448@30fps (w448p)
704x576@30fps (4CIF)
•
•
•
•
H.239 (H.323) dual stream
BFCP (SIP) dual stream
•
1024x768@60, 70, 75, 85 fps (XGA)
1280x1024@60, 75 fps (SXGA)
Available in MultiSite from any site
VIDEO FEATURES
Support for resolutions up to 1080p30 in both
main stream and dual stream simultaneously
•
•
•
•
Native 16:9 Widescreen
Advanced Screen Layouts
Intelligent Video Management
Local Auto Layout
1024x576@30fps (w576p)
640x480@30fps (VGA)
2 x YPbPr inputs, supported formats:
•
•
•
•
•
•
•
•
•
1920x1080@60fps (1080p60)
1920x1080@50fps (1080p50)
1920x1080@30fps (1080p30)
1920x1080@25fps (1080p25)
1280x720@60fps (720p60)
1280x720@50fps (720p50)
1280x720@30fps (720p30)
720x576@50fps (576p50)
720x480@60fps (w480p60)
MULTISITE FEATURES
800x600@30fps (SVGA)
1024x768@30fps (XGA)
1280x1024@30fps (SXGA)
1280x720@30fps (HD720p30)
1920x1080@30fps (HD1080p30)**
•
•
4-way High Definition SIP/H.323 MultiSite
Full Individual audio and video transcoding up
to 1080p30
VIDEO INPUTS (13 INPUTS)
4 x HDMI inputs, supported formats:
•
Individual layouts in MultiSite CP (Takes out
SelfView)
•
•
•
•
•
•
•
•
•
•
1920x1080@60 fps (1080p60)
1920x1080@50 fps (1080p50)
1920x1080@30 fps (1080p30)
1920x1080@25 fps (1080p25)
1280x720@60 fps (720p60)
1280x720@50 fps (720p50)
640x480@60 fps (480p60)
800x600@60 fps (SVGA)
•
•
•
•
•
•
H.323/SIP/VoIP in the same conference
Best Impression (Automatic CP Layouts)
H.264, Encryption, Dual Stream from any site
IP Downspeeding
AUDIO STANDARDS
•
G.711, G.722, G.722.1, 64 bit & 128 bit MPEG4
AAC-LD, AAC-LD Stereo
AUDIO FEATURES
Dial in/Dial out
1 x S-Video/Composite input (BNC connectors)*
PAL/NTSC
•
•
•
•
•
•
CD-Quality 20KHz Mono and Stereo
Eight separate acoustic echo cancellers
8-port Audio mixer
Conference rates up to 10 Mbps
•
PROTOCOLS
1024x768@60, 70, 75, 85 fps (XGA)
1280x1024@60, 75 fps (SXGA)
Extended Display Identification Data (EDID)
•
•
H.323
SIP
Automatic Gain Control (AGC)
Automatic Noise Reduction
Active lip synchronization
VIDEO OUTPUTS (5 OUTPUTS)
4 x HD-SDI inputs, supported formats:
2 x HDMI outputs, 2 x DVI-I outputs, supported
formats:
EMBEDDED ENCRYPTION
•
•
•
•
1920x1080@30 fps (1080p30)
1920x1080@25 fps (1080p25)
1280x720@60 fps (720p60)
1280x720@50 fps (720p50)
•
•
•
•
H.323/SIP point-to-point and multipoint calls
Standards-based: H.235 v2 & v3 and AES
Automatic key generation and exchange
Supported in Dual Stream & MultiSite
AUDIO INPUTS (14 INPUTS)
•
•
•
1920x1080@60fps (HD1080p60)
1280x720@60fps (HD720p60)
1366x768@60fps (WXGA)
•
8 x microphone, 48V phantom powered, XLR
connector each with separate echo cancellers
and noise reduction, all microphones can be
D14129.02—NOVEMBER 2008
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Appendices
Contents
Introduction
Getting started
About the menus
About the settings
Settings Library
Cameras
Contact us
IP NETWORK FEATURES
STORAGE AND TRANSPORT TEMPERATURE
MTBF PRODUCT RELIABILITY/MTBF
•
•
•
•
•
•
1920x1080@25fps
•
•
•
DNS lookup for service configuration
Differentiated Services (QoS)
•
-20° C to 60° C (-4° F to 140° F) at RH 10–90%
(non-condensing)
The predicted reliability is expressed in the
expected random Mean Time Between Failures
(MTBF) for the electronic components based on
the Power On Hours:
1280x720@60fps
1280x720@50fps
1280x720@30fps
1280x720@25fps
IP adaptive bandwidth management (including
flow control)
APPROVALS
•
•
Power On Hours (POH) > 69 000 hours
Useful Life Cycle > 6 years
•
•
•
•
•
•
•
Directive 2006/95/EC (Low Voltage Directive)
•
•
•
•
•
•
•
•
Auto gatekeeper discovery
Dynamic playout and lip-sync buffering
H.245 DTMF tones in H.323
Date and Time support via NTP
Packet Loss based Downspeeding
URI Dialing
Automatic or manual focus/brightness/
whitebalance
— Standard EN 60950-1
Directive 2004/108/EC (EMC Directive)
— Standard EN 55022, Class B
— Standard EN 55024
•
•
•
•
Far-end camera control
ISO 9001 certificate is available upon request
Daisy-chain support (Visca protocol camera)
Dual HDMI and HD-SDI output
— Standard EN 61000-3-2/-3-3
Upside-down mounting with automatic flipping
of picture
November 2008
Approved according to UL 60950-1 and CSA
60950-1-07
TCP/IP
DHCP
•
Complies with FCC15B Class B
SYSTEM MANAGEMENT
•
•
Support for the TANDBERG Management Suite
SECURITY FEATURES
DIMENSIONS
Total management via embedded SNMP,
Telnet, SSH, XML, SOAP
•
•
•
•
•
Management via HTTPS and SSH
IP Administration Password
Menu Administration Password
Disable IP services
•
•
•
•
Length: 17.36”/44.1cm
Height: 3.67”/9.3cm
Depth: 11.8”/30cm
•
Remote software upload: via web server, SCP,
HTTP, HTTPS
•
•
1 x RS-232 local control and diagnostics
Remote control and on-screen menu system
Weight: 11.22 lbs/5.1 kg
Network Settings protection
NETWORK INTERFACES
DIRECTORY SERVICES
*not supported in version 1
**requires option
•
2*** x separate LAN/Ethernet (RJ-45)
10/100/1000 Mbit
•
•
•
Support for Local directories (My Contacts)
Corporate Directory
***only one LAN/Ethernet interface supported in
version 1
Unlimited entries using Server directory
supporting LDAP and H.350
OTHER INTERFACES
•
•
•
USB host for future usage
USB device for future usage
GPIO*
•
Unlimited number for Corporate directory
(through TMS)
All specifications subject to change without notice,
system specifics may vary.
•
•
•
•
200 number local directory
Received Calls
PRECISIONHD 1080p CAMERA
Placed Calls
•
•
•
•
•
•
•
•
1/3” CMOS
All images in these materials are for
representational purposes only, actual products
may differ.
Missed Calls with Date and Time
12 x zoom
+15°/-25° tilt, +/- 90° pan
43.5° vertical field of view
72° horizontal field of view
Focus distance 0.3m–infinity
1920 x 1080 pixels progressive @ 60fps
POWER
•
•
•
Auto-sensing power supply
TANDBERG and Expressway are registered
trademarks or trademarks of TANDBERG in the
U.S. and other countries.
100–240 VAC, 50/60 Hz
175 watts max. for codec and main camera
Other formats supported (configurable through
Dip-switch):
OPERATING TEMPERATURE AND HUMIDITY
All other trademarks are property of their respective
owners.
•
0° C to 35° C (32° F to 95° F) ambient
temperature
•
•
•
1920x1080@60fps (HDMI only)
1920x1080@50fps (HDMI only)
1920x1080@30fps
•
10% to 90% Relative Humidity (RH)
D14129.02—NOVEMBER 2008
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec C90
Administrator Guide
Contact us
Contents
Introduction
Getting started
About the menus
About the settings
Settings Library
Cameras
Appendices
U.S. HEADQUARTERS
EUROPEAN HEADQUARTERS
TANDBERG
TANDBERG
1212 Avenue of the Americas
24th Floor
Philip Pedersens vei 20
1366 Lysaker
New York, NY 10036
Norway
Telephone: +1 212 692 6500
Fax: +1 212 692 6501
Telephone: +47 67 125 125
Fax: +47 67 125 234
Video: +47 67 126 126
E-mail: tandberg@tandberg.com
Video: +1 212 692 6535
E-mail: tandberg@tandberg.com
D14129.02—NOVEMBER 2008
65
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Singer Sewing Machine 132K1 User Manual
Singer Sewing Machine 1371A1 User Manual
Sony Camcorder Accessories SPK HCC User Manual
Sony Carrying Case LCM PC1 User Manual
Sony DVD Player DVP SR400P User Manual
Sony Universal Remote RM VZ220 User Manual
Star Micronics Network Card IP NPC User Manual
Swann DVR DVR4 950 User Manual
Sybase Server DC38029 01 0500 01 User Manual
SysKonnect Network Card SK 9Exx User Manual