TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
A
d
v
a
n
c
e
d
c
o
n
fi
g
u
r
a
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Software version TC3.0
MARCH 2010
Administrator guide
For TANDBERG Codec C90 and Profile 65” Dual using C90
1
D14635.02—MARCH 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
TANDBERG Codec C90 and Profiles using C90
Administrator guide
In
t
r
o
d
u
c
t
io
n
A
d
v
a
n
c
e
d
c
o
n
fi
g
u
r
a
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Contents
Document revision history
The Video Input Matrix..........................................................48
About the matrix ...............................................................48
Configure the video inputs................................................48
Default configurations.......................................................48
Revision 1: Initial release
Revision 2: Correction for an error on page 49
TANDBERG DNAM for Profile 65”.........................................49
The DNAM Loudspeaker ..................................................49
The DNAM Amplifier .........................................................49
CE Declarations....................................................................50
TANDBERG Codec C90 ...................................................50
TANDBERG Profile using Codec C90...............................50
China RoHS table................................................................. 51
Supported RFCs in SIP......................................................... 52
Current RFCs and drafts supported in SIP ....................... 52
Media capabilities supported in SIP.................................. 52
Technical specifications........................................................53
TANDBERG Profile 65” Dual .............................................53
TANDBERG Codec C90 ...................................................55
3
D14635.02—MARCH 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
A
d
v
a
n
c
e
d
c
o
n
fi
g
u
r
a
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Introduction
Chapter 1
Introduction
4
D14635.02—MARCH 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
A
d
v
a
n
c
e
d
c
o
n
fi
g
u
r
a
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Introduction
The purpose of this document
The purpose of this document is to provide you with
information required to administrate your product at an
advanced level.
Introduction
Products covered in this guide
You may already be familiar with the administrator guides
for the Profile Series and Codec C Series. To help you find
•
•
TANDBERG Profile 65” Dual using C90
TANDBERG Codec C90
the information you need, TANDBERG has split the guides
into smaller and more accessible parts listed on the right
of this page.
Other documents you might find useful
Disclaimers and Notices
•
•
•
•
•
•
•
•
•
•
Video conference room primer guide
The objective of this documentation is to provide the
reader with assistance in using and configuring the
product. The capabilities of TANDBERG products and
other manufacturers’ products change over time and
so the required configuration may be different from
that indicated here. If you have any suggestions for
changes to this document, please feed them back
to TANDBERG through your TANDBERG Authorized
Service Representative.
Getting started guide for Profile Series, Codec C Series, Quick Set C20
User Guide for Profile Series, Codec C Series and Quick Set C20
Administrator guide for Profiles using Codec C20 and Quick Set C20
Administrator guide for Profiles using Codec C60 and Codec C60/C40
Administrator guide for Profiles using Codec C90 and Codec C90
Camera user guide for PrecisionHD 1080p/720p
If you need technical support, please contact your
TANDBERG Authorized Service Representative.
API guides for Codec C90, C60, C40
Physical interfaces guides for Codec C90, C60, C40
The specifications for the product and the information
in this Guide are subject to change at any time, without
notice, by TANDBERG. Every effort has been made to
Legal and safety information for Profile Series, Codec C Series and
Quick Set C20
supply complete and accurate information in this Guide;
however, TANDBERG assumes no responsibility or
liability for any errors or inaccuracies that may appear in
this document.
Download the user documentation
TANDBERG® is a registered trademark belonging to
Tandberg ASA. Other trademarks used in this document
are the property of their respective holders.
This Guide may be reproduced in its entirety, including
all copyright and intellectual property notices, in limited
quantities in connection with the use of this product.
Except for the limited exception set forth in the previous
sentence, no part of this Guide may be reproduced,
stored in a retrieval system, or transmitted, in any
form, or by any means, electronically, mechanically, by
photocopying, or otherwise, without the prior written
permission of TANDBERG.
© 2010 TANDBERG
5
D14635.02—MARCH 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
A
d
v
a
n
c
e
d
c
o
n
fi
g
u
r
a
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Introduction
disturb’ is active will be presented in the middle of the screen, if
you have no menus or presentation active.
New features and improvements
Configuration profiles
What’s new in this version
The information on this page describes the highlights and main
changes in the new version for the C Series line of codecs.
Do not disturb can be activated by holding down the disconnect
key until the Standby dialog box appears.
Enhanced usability features with Configuration Profiles. The
functionality is available from softkeys when you enter the
“Advanced Configuration” menu.
New menu languages
Software release notes
Finnish, Traditional Chinese, Portuguese Brazilian, Polish, Danish,
Dutch
Today’s bookings
For a complete overview of the news and changes, we
recommend reading the TANDBERG TC Software Release Notes
Systems provisioned by the TANDBERG Management System
(TMS) can display today’s current bookings in the GUI.
Call rate selection
The soft button to select call rate is now available from the ‘Enter
contact’ field in the call dialog box.
Confirm selection of video output resolution
User documentation
You may already be familiar with the user guides for the Profile
Series, Codec C Series and Quick Set C20. To help you find the
information you need, TANDBERG has split the guides into smaller
and more accessible parts.
When changing the output resolution, the system will prompt you
and let you keep or cancel the selected resolution. In the event
that the monitor doesn’t support the new selected resolution, no
prompt will be shown; selection will time out and thus the system
will revert to the previous resolution.
Improved web interface
The web interface lets you:
•
•
•
•
•
•
•
•
Check system info
The Administrator Guide has been split into:
System information, frame rate indicator
Upgrade software and add release and option keys
Configure the system using the advanced configuration
Upload custom wallpaper using png format.
Place calls and see the call status
Upload Certificates
The call status will now include frame rate, thus making it easy to
see if you are sending/receiving 30 or 60 frames per second. As
this is just an indicator and not a proper frame rate counter, it will
not show accurate sent or received frame rate. However you will
be able to see if the system is now sending or receiving 60 frames
per second.
•
•
•
•
•
Getting started guide
Video conference room primer guide
Camera user guide
Administrator guide (smaller size)
Legal and safety information
Download XML files
Autocomplete
Download system logs
When starting to type in a number in the call dialog box, it will now
provide matches from recent calls, corporate phonebook and
local contacts.
The System Integrator Guide has been split into:
•
•
API guides for Codec C90, C60, C40
Video enhancements
Physical interfaces guides for Codec C90, C60, C40
Telephone call icon
Optimal Definition Profiles
A telephone call icon will now be displayed along with the
telephone number when combined with a video call or
presentation.
The User Guides have been merged into one guide:
Each video input can now be configured to allow different optimal
definition profiles. You can set the profile level, which tells your
system how good lighting you have in your room, and you can set
when to prefer 60 frames per second over 30 frames per second.
•
User Guide for Profile Series, Codec C Series and Quick Set
C20
Russian Input method
The user documentation is available from our web site. Select
your product from the drop down list to see an overview of the
user documnetation for that product.
Overscan compensation
When Cyrillic is selected as input method, Russian can be used
as multitap. A Russian version of the remote control will be
available at the same time as the TC3.0 release.
Support for monitor overscan compensation, where both video
and GUI will be scaled to support monitors that do not support
the ability to display an image in pixel-by-pixel mode.
Do Not Disturb
A proper icon will now be displayed in the lower right corner, when
do not disturb is active. And a text box reminding you that ‘Do not
6
D14635.02—MARCH 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
A
d
v
a
n
c
e
d
c
o
n
fi
g
u
r
a
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Introduction
Video enhancements, continued...
Audio enhancements
New encoding and decoding resolutions
Equalizer
Supported systems: C40, C60, C90. Audio equalizer, available
in the API and the TANDBERG Audio Console. Can be turned on
and off from the GUI, but the equalizer values must be set using
the API.
•
•
WUXGA (1920*1200)
WXGA+ (1440*900) (only Codec C90 and C60)
Letterbox removal
Audio and video source association
The system will detect letterboxing or pillar boxing and scale the
image to fit the screen. If the system receives a 4/3 image with
letterboxing (16/9), it will scale the image to fit the entire screen.
Supported systems: C40, C60, C90. When set to on, you have
the ability to associate an audio input to a video input, meaning
the audio input will only be active when that video source is active.
Improved video layout control
Stereo echo cancellation
It is now possible to configure which layout family to be used as
default in any system state. This allows for having default self view
on the second monitor for dual monitor systems.
Supported systems: C90. Only available for the line inputs.
This functionality has to be configured using the API (dataport).
Integrator benefits
Improved packet loss resilience
•
•
For Integrators, GPIO is available on the C90 and C60
The packet loss concealment has been improved, which provides
noticeable better performance over previous software versions in
packet loss environments.
Improved Audio Console features. The Audio console
application is available from the TANDBERG Developer Zone
•
•
The new Factory Reset command will reset all configurations
and passwords, all logs will be deleted, all uploaded files
(wallpapers etc) will be deleted. The option keys and release
keys will not be deleted.
ClearPath (Experimental mode)
Available in TC3.0 in the Experimental menu as a technology
preview, and should only be used for demonstration purposes.
ClearPath is TANDBERG’s solution to minimize the negative
effects of packet loss in a non-optimal network.
New and changed API commands. See the API guides for the
Must be enabled from the API or GUI. See the: Experimental
Conference PacketLossResilience configuration.
Camera
With the TC3.0.0 release, the PrecisionHD 1080p camera will
automatically be upgraded to camera software release ID40056.
Included in this release is:
•
•
Ability to set DHCP to on over Visca.
Added visca commands for changing integration time manually
between 50 and 60Hz. To be used if the camera is not able to
detect the power frequency.
7
D14635.02—MARCH 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
A
d
v
a
n
c
e
d
c
o
n
fi
g
u
r
a
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Introduction
TANDBERG Profile 65” Dual at a
glance
The TANDBERG Profile 65” Dual is delivered with:
Presentation unit
Codec C90
Main system
•
•
•
•
Full HD video
High resolution data sharing
Full HD Multisite
PrecisionHD
1080p camera
Rich I/O capabilities
PrecisionHD 1080p
Full HD Camera designed for visual communication with:
2 x Monitor 65’’
•
•
12 x optical zoom
Fast and precise pan, tilt and zoom
Dual monitor 65”
Audio amplifier
(DNAM)
Full HD LCD Display
Audio module
Wide band audio module supporting:
Codec C90
Foot stand
•
•
•
20 kHz AAC-LD
Full echo canceling
Stereo
Audio amplifier
Optimized DNAM for TANDBERG Profile providing crystal clear
and natural audio.
Microphones
3 x Microphones
Remote control
3 x Microphones with cables
Remote control
•
TANDBERG Remote Control TRC5 with 4 x AAA batteries
Foot stand
Floor standing foot plate
8
D14635.02—MARCH 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
A
d
v
a
n
c
e
d
c
o
n
fi
g
u
r
a
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Introduction
Design Features
Integrator package
The integrator package of the TANDBERG Codec C90 comes
with the TANDBERG PrecisionHD 1080p camera and two
microphones and cables.
TANDBERG Codec C90 at a glance
•
The best, most powerful codec available with the ultimate
video and audio quality.
The TANDBERG Codec C90 is used in telepresence and
collaboration projects, having the ultimate collaboration engine
with HD video & audio, tremendous power and the highest level of
flexibility for any projects.
•
2U high, rack mountable, with special rack mounting solution
included.
•
•
•
Professional grade connectors.
Unmatched quality and flexibility.
Standards-compliant 1080p solution-compatible with
standards-based video without losing features.
Application Features
•
•
1080p30 HD Individual Transcoding embedded Multisite.
Collaborate on virtually anything with 5 simultaneous video
inputs.
•
HD Collaboration with 1080p30 or UXGA (UXGA ready and
available with future software).
•
•
Limitless integration possibilities.
Ideal for telepresence and collaboration studios, boardrooms,
auditoriums, education and tele-medicine applications.
Performance Features
•
•
Optimal Definition up to 1080p.
H.323/SIP up to 6 Mbps point-to-point; up to 10 Mbps total
MultiSite bandwidth.
•
Connect up to 12 HD sources and 8 microphones directly into
the interface.
•
•
•
Full Duplex Audio with High Quality Stereo Sound.
Full APIs, see the API Guide for Codec C90.
Takes advantage of the TANDBERG Total Solution with
Management, Transcoded HD MultiSite™, Recording and
Streaming, Firewall Traversal.
9
D14635.02—MARCH 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Advanced config.
Chapter 2
Advanced configuration settings
10
D14635.02—MARCH 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Advanced config.
The Audio settings, continued...
Description of the advanced configuration settings
In the following pages you will find a complete list of the system settings which are configured from
the Advanced configuration menu. Open the Home menu on screen and go to: Settings > Advanced
> Advanced configuration. The examples shows either the default value or an example of a value.
Audio Input Line [1..4] Equalizer ID
Select equalizer ID[1...8].
Valuespace: <1..8>
Range: Select EqualizerID 1 to 8.
The Audio settings
Example: Audio Input Line 1 Equalizer ID: 1
Audio Input Line [1..4] Equalizer Mode
Determines whether or not the selected equalizer is enabled.
Audio Input HDMI [3, 4] Level
Defines the input level of the selected HDMI input connector in steps of 1dB from -24dB to 0dB.
See the Audio Level tables in the Physical Interfaces Guide for the codec for a complete overview of the
menu values represented indB.
Valuespace: <On/Off>
On: Use the selected equalizer
Off: No equalizer
Valuespace: <-24..0>
Range: -24 to 0dB
Example: Audio Input Line 1 Equalizer Mode: Off
Example: Audio Input HDMI 3 Level: 0
Audio Input Line [1..4] VideoAssociation MuteOnInactiveVideo
Audio Input HDMI [3, 4] Mode
Enable association of a video source to a Line audio input.
Determines whether or not the audio channels on the HDMI input should be enabled. The HDMI input 3
and 4 have two audio channels.
Valuespace: <On/Off>
On: A video source is associated, and the audio will be muted if the associated video source is not
displayed.
Valuespace: <On/Off>
On: Set to On to enable the audio channels on the selected HDMI input.
Off: Set to On to disable the audio channels on the selected HDMI input.
Off: No video source is associated.
Example: Audio Input Line 1 VideoAssociation MuteOnInactiveVideo: Off
Example: Audio Input HDMI 3 Mode: On
Audio Input Line [1..4] VideoAssociation VideoInputSource
Audio Input HDMI [3..4] VideoAssociation MuteOnInactiveVideo
Select the associated video input source.
Enable association of a video source to a HDMI audio input.
Valuespace: <1/2/3/4/5>
Valuespace: <On/Off>
Range: Select one of the five video input sources for the Line input.
On: A video source is associated, and the audio will be muted if the associated video source is not
displayed.
Example: Audio Input Line 1 VideoAssociation VideoInputSource: 1
Off: No video source is associated.
Audio Input Line [1..4] Channel
Defines whether the Audio Line input is a mono signal or part of a multichannel signal.
Example: Audio Input HDMI 3 VideoAssociation MuteOnInactiveVideo: Off
Valuespace: <Left/Right/Mono>
Audio Input HDMI [3..4] VideoAssociation VideoInputSource
Select the associated video input source.
Left: The Audio Line input signal is the left channel of a stereo signal.
Right: The Audio Line input signal is the right channel of a stereo signal.
Mono: The Audio Line input signal is a mono signal.
Valuespace: <1/2/3/4/5>
Range: Select one of the five video input sources for the selected HDMI input.
Example: Audio Input 1 Channel: Left
Example: Audio Input HDMI 3 VideoAssociation VideoInputSource: 1
11
Download from Www.Somanuals.com. All Manuals Search And Download.
D14635.02—MARCH 2010
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Advanced config.
The Audio settings, cont...
The Audio settings, cont...
Audio Input Line [1..4] Level
Audio Input Microphone [1..8] Equalizer Mode
Defines the input level of the selected Line input connector in steps of 1dB from 0dB to 24dB.
Determines whether or not the selected equalizer is enabled.
See the Audio Level tables in the Physical Interfaces Guide for the codec for a complete overview of the
menu values represented in dB.
Valuespace: <On/Off>
On: Use the selected equalizer
Off: No equalizer
Valuespace: <0..24>
Range: 0 to 24dB
Example: Audio Input Microphone 1 Equalizer Mode: Off
Example: Audio Input Line 1 Level: 10
Audio Input Microphone [1..8] EchoControl Mode
Audio Input Line [1..4] LoopSuppression
Loop suppression detects whether a delayed signal loop is present from an audio Line output to an audio
Line input on the codec. If a loop is detected this unwanted feedback is suppressed.
The echo canceller continuously adjusts itself to the audio characteristics of the room and compensate for
any changes it detects in the audio environment. If the changes in the audio conditions are very significant
the echo canceller may take a second or two to re-adjust.
NOTE! Only loops between line output 3 and line input 3, and between line output 4 and line input 4 are
suppressible.
Valuespace: <On/Off>
On: Echo Control is normally set to On to prevent the far end from hearing their own audio. Once
Valuespace: <On/Off>
selected, echo cancellation is active at all times.
On: Set to On to activate Loop Suppression.
Off: Set to Off to deactivate Loop Suppression.
Off: Echo Control should be switched Off if external echo cancellation or playback equipment is used.
Example: Audio Input Microphone 1 EchoControl Mode: On
Example: Audio Input Line 3 LoopSuppression: On
Audio Input Microphone [1..8] EchoControl NoiseReduction
Audio Input Line [1..4] Mode
Determines whether or not an Audio Line input is enabled.
The system has a built-in noise reduction which reduces constant background noise (e.g. noise from
air-conditioning systems, cooling fans etc.). In addition, a high pass filter (Humfilter) reduces very low
frequency noise. Requires the Echo Control Mode to be enabled for the selected microphone.
Valuespace: <On/Off>
Valuespace: <On/Off>
On: Set to On to enable the Audio Line input.
Off: Set to Off to disable the Audio Line input.
On: The Noise Reduction should be set to On in the presence of low frequency noise.
Off: Turns Noise Reduction Off for the selected microphone connector.
Example: Audio Input Line 1 Mode: On
Example: Audio Input Microphone 1 EchoControl NoiseReduction: On
Audio Input Microphone [1..8] Equalizer ID
Select equalizer ID[1...8]
Audio Input Microphone [1..8] VideoAssociation MuteOnInactiveVideo
Enable association of a video source to the selected microphone connector.
Valuespace: <1..8>
Valuespace: <On/Off>
Range: Select EqualizerID 1 to 8.
On: A video source is associated, and the audio will be muted if the associated video source is not
Example: Audio Input Microphone 1 Equalizer ID: 1
displayed.
Off: No video source is associated.
Example: Audio Input Microphone 1 VideoAssociation MuteOnInactiveVideo: On
12
Download from Www.Somanuals.com. All Manuals Search And Download.
D14635.02—MARCH 2010
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Advanced config.
The Audio settings, cont...
The Audio settings, cont...
Audio Output HDMI [1, 3] Level
Audio Input Microphone [1..8] VideoAssociation VideoInputSource
Select the associated video input source.
Defines the output level of the selected HDMI output connector in steps of 1dB from -24dB to 0dB.
See the Audio Level tables in the Physical Interfaces Guide for the codec for a complete overview of the
menu values represented indB.
Valuespace: <1/2/3/4/5>
Range: Select one of the five video input sources for the microphone connector.
Valuespace: <-24..0>
Example: Audio Input Microphone 1 VideoAssociation VideoInputSource: 1
Range: -24 to 0dB
Example: Audio Output HDMI 1 Level: 0
Audio Input Microphone [1..8] Level
Defines the input level of the selected microphone connector in steps of 1dB from 0dB to 24dB.
Audio Output HDMI [1, 3] Mode
Determines whether or not the audio channel on the selected HDMI output connector should be enabled.
See the Audio Level tables in the Physical Interfaces Guide for the codec for a complete overview of the
menu values represented indB.
Valuespace: <0..24>
Valuespace: <On/Off>
Range: 0 to 24dB
On: Set to On to enable the audio channel on the selected HDMI output.
Off: Set to On to disable the audio channel on the selected HDMI output.
Example: Audio Input Microphone 1 Level: 15
Example: Audio Output HDMI 1 Mode: On
Audio Input Microphone [1..8] Mode
Determines whether or not athe selected microphone connector is enabled.
Audio Output Line [1..6] Channel
Defines whether the Audio Line output is a mono signal or part of a multichannel signal.
Valuespace: <On/Off>
On: Set to On to enable the microphone connector.
Off: Set to Off to disable the microphone connector.
Valuespace: <Left/Right/Mono>
Left: The Audio Line output signal is the left channel of a stereo signal.
Right: The Audio Line output signal is the right channel of a stereo signal.
Mono: The Audio Line output signal is a mono signal.
Example: Audio Input Microphone 1 Mode: On
Example: Audio Output Line 1 Channel: left
Audio Input Microphone [1..8] Type
The microphone connectors are intended for electret type microphones. The selected microphone
connector can be set to line or microphone mode.
Audio Output Line [1..6] Equalizer ID
Valuespace: <Microphone/Line>
Select equalizer ID[1...8]
Microphone: 48 V Phantom voltage and pre-amplification is On
Valuespace: <1..8>
Line: Select Line when you have a standard balanced line input. The phantom voltage and pre-
amplification is Off.
Range: Select EqualizerID 1 to 8.
Example: Audio Output Line 1 Equalizer ID: 1
Example: Audio Input Microphone 1 Type: Line
Audio Output Line [1..6] Equalizer Mode
Determines whether or not the selected equalizer is enabled.
Valuespace: <On/Off>
On: Use the selected equalizer
Off: No equalizer
Example: Audio Output Line 1 Equalizer Mode: Off
13
Download from Www.Somanuals.com. All Manuals Search And Download.
D14635.02—MARCH 2010
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Advanced config.
The Audio settings, cont...
Audio Output Line [1..6] Level
The Audio settings, cont...
Audio SoundsAndAlerts RingTone
Defines the output level of the selected Audio Output Line connector in steps of 1dB from -24dB to 0dB.
Selects the ring tone for incoming calls.
See the Audio Level tables in the Physical Interfaces Guide for the codec for a complete overview of the
menu values represented indB.
Valuespace: <Marbles/IceCrystals/Polaris/Alert/Discrete/Fantasy/Jazz/Nordic/Echo/Rhythmic>
Range: Select a tone from the list of ring tones.
Valuespace: <-24..0>
Example: Audio SoundsAndAlerts RingTone: Jazz
Range: -24 to 0dB
Example: Audio Output Line 1 Level: -10
Audio SoundsAndAlerts RingVolume
Sets the ring tone volume[0-100] for an incoming call in steps of 0.5dB from -34.5dB to 15dB.
Audio Output Line [1..6] Mode
Determines whether or not the selected Audio Line output connector is enabled.
Valuespace: <0..100>
Range: Select a value from 0 to 100. Volume 0 = Off.
Valuespace: <On/Off>
Example: Audio SoundsAndAlerts RingVolume: 50
On: Set to On to enable the Audio Line output.
Off: Set to Off to disable the Audio Line output.
Audio Volume
Example: Audio Output Line 1 Mode: On
Sets the volume level [0-100] on the loudspeaker output in steps of 0.5dB from -34.5dB to 15dB.
Valuespace: <0..100>
Audio Output Line [1, 3] Type
Determines if the selected Audio Line output connector is an analog or digital type output.
Range: Select a value from 0 to 100. Volume 0 = Off.
Example: Audio Volume: 70
Valuespace: <Auto/SPDIF>
Auto: If a TANDBERG Digital NAM is detected then SPDIF mode will be selected, otherwise analog
mode will be selected.
SPDIF: Set to SPDIF when you want the Audio Line 1 or 3 output to be in digital mode.
Example: Audio Output Line 1 Type: Auto
Audio Output Line [2, 4, 5, 6] Type
Line output 2, 4, 5, 6 are dedicated analog outputs, hence type can be set to analog only.
Valuespace: <Analog>
Can be set to analog only.
Example: Audio Output Line 2 Type: Analog
Audio SoundsAndAlerts KeyTones Mode
The system can produce a sound every time a key on the remote control is pressed.
Valuespace: <On/Off>
On: There will be a sound indicator when pressing keys on the remote control.
Off: The remote control Key Tones is switched off.
Example: Audio SoundsAndAlerts KeyTones Mode: Off
14
Download from Www.Somanuals.com. All Manuals Search And Download.
D14635.02—MARCH 2010
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Advanced config.
The Camera settings
The Camera settings, cont...
Cameras PowerLine Frequency
Cameras Camera [1..7] Flip
.Applies to cameras supporting PowerLine frequency anti-flickering, i.e PrecisionHD 1080p cameras.
With Flip mode (vertical flip) you can flip the image upside down.
Valuespace: <Auto/50Hz/60Hz>
Valuespace: <Auto/On/Off>
Auto: Set to Auto to enable power frequency auto detection in the camera.
50Hz/60Hz: Set to 50Hz or 60Hz.
Auto: When the camera is placed upside down the image is automatically flipped upside down. Use
this setting with cameras that can be mounted upside down, and that can auto detect that the camera
is mounted upside down.
Example: Cameras PowerLine Frequency: Auto
On: When set to On the video on screen is flipped. This setting is used with cameras that can be
mounted upside down, but cannot auto detect that the camera is mounted upside down.
Off: Set to Off to display the video on screen the normal way.
Cameras Camera [1..7] Backlight
Backlight is used to compensate for lights shining directly at the camera (usually the sun entering the
window) to avoid a too dark image from the room.
Example: Cameras Camera 1 Flip: Off
Valuespace: <On/Off>
Cameras Camera [1..7] Focus Mode
Set the camera focus mode.
On: Set to On to turn on the backlight compensation.
Off: Set to Off to turn the backlight compensation off.
Valuespace: <Auto/Manual>
Example: Cameras Camera 1 Backlight: Off
Auto: When set to Auto the focus will be updated throughout the call. When moving the camera, the
system will use auto focus for a few seconds to set the right focus of the new camera position. After a
few seconds auto focus is turned off to prevent continuous focus adjustments of the camera.
Cameras Camera [1..7] Brightness Level
Define the Brightness Level for the selected camera. Requires the Brightness Mode to be set to manual.
Manual: If set to Manual the focus is adjusted manually.
Example: Cameras Camera 1 Focus Mode: Auto
Valuespace: <1..31>
Range: Select a value from 1 to 31.
Cameras Camera [1..7] Gamma Level
Example: Cameras Camera 1 Brightness Level: 1
By setting the Gamma Level you can select which gamma correction table to use. This setting may be
useful in difficult lighting conditions, where changes to the brightness setting does not provide satisfactory
results. Requires the Gamma Mode to be set to Manual.
Cameras Camera [1..7] Brightness Mode
Adjust the camera brightness.
Valuespace: <0..7>
Range: Select a value from 0 to 7.
Valuespace: <Auto/Manual>
Auto: When set to Auto, the camera brightness is automatically set by the system.
Example: Cameras Camera 1 Gamma Level: 0
Manual: Set to Manual to enable manual control of the camera brightness, e.g. the level of the
brightness level setting will be used for the camera.
Cameras Camera [1..7] Gamma Mode
Example: Cameras Camera 1 Brightness Mode: Auto
Applies to cameras which supports Gamma mode. The Gamma Mode setting enables for gamma
corrections. Gamma describes the nonlinear relationship between image pixels and monitor brightness.
The TANDBERG PrecisionHD camera supports Gamma Mode. Not supported on The TANDBERG
PrecisionHD 1080p camera.
Valuespace: <Auto/Manual>
Auto: Auto is the default and the recommended setting.
Manual: In severe light conditions, you may switch mode to manual and specify explicitly which gamma
table to use by setting the Gamma Level.
Example: Cameras Camera 1 Gamma Mode: Auto
15
Download from Www.Somanuals.com. All Manuals Search And Download.
D14635.02—MARCH 2010
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Advanced config.
The Camera settings, cont...
Cameras Camera [1..7] IrSensor
The Camera settings, cont...
Cameras Camera [1..7] DHCP
The Camera IR setting determines whether the infrared receiver at the camera should be enabled or not.
The IR sensor LED is located in the front of the camera and flickers when the IR sensor is activated from
the remote control.
Applies to cameras which supports DHCP, i.e the PrecsisionHD 1080p cameras. The camera must be
connected to a LAN. When set, the command enables support for SW upgrade of daisy chained cameras.
It will enable the camera’s DHCP function and force start of MAC and IP address retrieval. Remember to
reset the DHCP when the camera is no longer connected to a LAN.
Valuespace: <On/Off>
Valuespace: <On/Off>
On: Set to On to enable the IR sensor on the camera.
Off: Set to Off to disable the IR sensor on the camera.
On: Set to On to enable DHCP in the camera. The camera is automatically re-booted. After re-boot the
DHCP is started and the IP address will be retrieved. Run the commnand “xStatus Camera” for result.
Example: Cameras Camera 1 IrSensor: On
Off: Set to Off will disable DHCP in the camera. NOTE: When camera is not connected to a LAN, this
setting should be applied.
Cameras Camera [1..7] Mirror
Example: Cameras Camera 1 DHCP: Off
With Mirror mode (horizontal flip) you can mirror the image on screen.
Valuespace: <Auto/On/Off>
Auto: When the camera is placed upside down the image is automatically mirrored. Use this setting
with cameras that can be mounted upside down, and that can auto detect that the camera is mounted
upside down.
On: Set to On to see the selfview in mirror mode, e.g. the selfview is reversed and the experience of
selfview is as seeing yourself in a mirror.
Off: Set to Off to see the selfview in normal mode, e.g. the experience of selfview is as seeing yourself
as other people see you.
Example: Cameras Camera 1 Mirror: Off
Cameras Camera [1..7] Whitebalance Level
Define the Whitebalance Level for the selected camera. Requires the Whitebalance Mode to be set to
manual.
Valuespace: <1..16>
Range: Select a value from 1 to 16.
Example: Cameras Camera 1 Whitebalance Level: 1
Cameras Camera [1..7] Whitebalance Mode
Set the camera whitebalance mode.
Valuespace: <Auto/Manual>
Auto: When set to Auto, the camera will continuously adjust the whitebalance depending on the
camera view.
Manual: Set to Manual to enable manual control of the camera whitebalance, e.g. the level of the
whitebalance level setting will be used for the camera.
Example: Cameras Camera 1 Whitebalance Mode: auto
16
Download from Www.Somanuals.com. All Manuals Search And Download.
D14635.02—MARCH 2010
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Advanced config.
The Conference settings
The Conference settings, cont...
Conference [1..1] DoNotDisturb Mode
Conference [1..1] AutoAnswer Delay
Defines how long (in seconds) an incoming call has to wait before it is answered automatically by the
system. Requires the Autoanswer Mode to be enabled.
The Do Not Disturb setting determines whether or not there should be an alert on incoming calls.
Valuespace: <On/Off>
Valuespace: <0..50>
On: Set to On when you want no alert to incoming calls. The calling side will receive a busy signal when
Range: 0-50 seconds
trying to call the codec.
Off: This is the default setting. The DoNotDisturb is automatically turned Off if the codec receives any
IR signal from the handheld remote control.
Example: Conference 1 AutoAnswer Delay: 0
Example: DoNotDisturb Mode: Off
Conference [1..1] AutoAnswer Mode
Set the Autoanswer mode.
Conference [1..1] IncomingMultisiteCall Mode
The Incoming Multisite Call setting determines whether or not the system should accept incoming calls to
an already active conference.
Valuespace: <On/Off>
On: The system will automatically answer all incoming calls.
Off: All incoming call must be answered manually by pressing the OK key or the green Call key on the
remote control.
Valuespace: <Allow/Deny>
Allow: When set to Allow, and with an ongoing MCU call/conference, the user can accept another
incoming call. This will result in the incoming call being added to the MCU conference.
Example: Conference 1 AutoAnswer Mode: Off
Deny: The system will not accept incoming calls when you are in a call. The calling side will receive a
busy signal.
Conference [1..1] AutoAnswer Mute
The Autoanswer Mute setting determines whether the microphone is muted when an incoming call is
automatically answered.
Example: Conference 1 IncomingMultisiteCall Mode: Allow
Valuespace: <On/Off>
Conference [1..1] FarEndControl Mode
Lets you decide if the remote side (far end) should be allowed to select your video sources and control
your local camera (pan, tilt, zoom).
On: The incoming call will be muted when automatically answered.
Off: The incoming call will not be muted.
Example: Conference 1 AutoAnswer Mute: Off
Valuespace: <On/Off>
On: Set to On when you want the far end to be able to select your video sources and control your local
camera (pan, tilt, zoom). You will still be able to control your camera and select your video sources as
normal.
Conference [1..1] MicUnmuteOnDisconnect
The MicUnmuteOnDisconnect setting determines if the microphones should be automatically unmuted
when all calls are disconnected. In a meeting room or other shared resource this could be done to prepare
the system for the next user.
Off: When set to Off the far end can not access any of the features above on your system.
Example: Conference 1 FarEndControl Mode: On
Valuespace: <On/Off>
On: Microphones will be unmuted when all calls are disconnected
Off: Microphones will not be unmuted when all calls are disconnected
Example: Conference 1 MicUnmuteOnDisconnect: On
17
Download from Www.Somanuals.com. All Manuals Search And Download.
D14635.02—MARCH 2010
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Advanced config.
The Conference settings, cont...
Conference [1..1] Encryption Mode
The Conference settings, cont...
Conference [1..1] VideoBandwidth MainChannel Weight
In Point to point calls (BestEffort mode): If the far end system supports encryption (AES-128), the call will
be encrypted. If not, the call will proceed without encryption.
The available transmit video bandwidth is distributed on the main channel and presentation channel
according to “MainChannel Weight” and “PresentationChannel Weight”. If the main channel weight is 2
and the presentation channel weight is 1, then the main channel will use twice as much bandwidth as the
presentation channel.
In MultiSite calls (BestEffort mode): In order to have encrypted MultiSite conferences, all sites must
support encryption. If not, the conference will be unencrypted.
Icons on screen: A padlock with the text “Encryption On” displays on screen, for a few seconds, when the
conference starts.
Valuespace: <1..10>
Range: Select a value from 1 to 10.
Valuespace: <Off/On/BestEffort>
Example: Conference 1 VideoBandwidth MainChannel Weight: 5
BestEffort: The system will use encryption whenever possible.
On: The system will only allow calls that are encrypted.
Off: The system will not use encryption.
Conference [1..1] VideoBandwidth PresentationChannel Weight
The available transmit video bandwidth is distributed on the main channel and presentation channel
according to “MainChannel Weight” and “PresentationChannel Weight”. If the main channel weight is 2
and the presentation channel weight is 1, then the main channel will use twice as much bandwidth as the
presentation channel.
Example: Conference 1 Encryption Mode: BestEffort
Conference [1..1] DefaultCall Protocol
Specify the Default Call Protocol to be used when placing calls from the system. The call protocol can also
be defined directly for each call when setting up a call.
Valuespace: <1..10>
Range: Select a value from 1 to 10.
Example: Conference 1 VideoBandwidth PresentationChannel Weight: 5
Valuespace: <H323/SIP>
H.323: Select H.323 to ensure that calls are set up as a H.323 calls.
SIP: Select SIP to ensure that calls are set up as a SIP calls.
Example: Conference 1 DefaultCall Protocol: H323
Conference [1..1] DefaultCall Rate
Specify the Default Call Rate to be used when placing calls from the system. The call rate can also be
defined directly for each call when setting up a call.
Valuespace: <64..6000>
Range: 64-6000kbps
Example: Conference 1 DefaultCall Rate: 768
Conference [1..1] VideoBandwidth Mode
In “Dynamic” mode the available transmit bandwidth for the video channels is distributed among the
currently active channels. This means that the main video channels will use the bandwidth of the
presentation channel, if there is no active presentation. In “Static” mode the bandwidth is assigned to each
video channel even if it is not active.
Valuespace: <Dynamic/Static>
Dynamic: The available transmit bandwidth for the video channels are distributed among the currently
active channels.
Static: The available transmit bandwidth is assigned to each video channel, even if it is not active.
Example: Conference 1 VideoBandwidth Mode: Dynamic
18
Download from Www.Somanuals.com. All Manuals Search And Download.
D14635.02—MARCH 2010
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Advanced config.
The GPIO settings
The H323 settings
GPIO Pin [1..4] Mode
H323 Profile [1..1] Authentication LoginName
The four GPIO pins can be configured individually. The state can be retrieved by “xStatus GPIO Pin [1..4]
The system sends the Authentication Login Name and the Authentication Password to a H.323
State”. The default pin state is High (+12V). When activated as output, they are set to 0V. To activate them
as input, they must be pulled down to 0V.
Gatekeeper for authentication. The authentication is a one way authentication from the codec to the H.323
Gatekeeper, i.e. the system is authenticated to the gatekeeper. If the H.323 Gatekeeper indicates that no
authentication is required, the system will still try to register. Requires the H.323 Gatekeeper Authentication
Mode to be enabled.
Valuespace: <InputNoAction/OutputManualState/OutputInCall/OutputMicrophonesMuted/
OutputPresentationOn/OutputAllCallsEncrypted/InputMuteMicrophones>
Valuespace: <S: 0, 50>
InputNoAction: The pin state can be set, but no operation is performed.
Format: String with a maximum of 50 characters.
OutputManualState: The pin state can be set by “xCommand GPIO ManualState Set PinX: <High/
Low>” (to +12V or 0V, respectively).
Example: H323 Profile 1 Authentication LoginName: “”
OutputInCall: The pin is activated when in call, deactivated when not in call.
OutputMicrophonesMuted: The pin is activated when microphones are muted, deactivated when not
muted.
H323 Profile [1..1] Authentication Password
The system sends the Authentication Login Name and the Authentication Password to a H.323
Gatekeeper for authentication. The authentication is a one way authentication from the codec to the H.323
Gatekeeper, i.e. the system is authenticated to the gatekeeper. If the H.323 Gatekeeper indicates that no
authentication is required, the system will still try to register. Requires the H.323 Gatekeeper Authentication
Mode to be enabled.
OutputPresentationOn: The pin is activated when presentation is active, deactivated when presentation
is not active.
OutputAllCallsEncrypted: The pin is activated when all calls are encrypted, deactivated when one or
more calls are not encrypted.
InputMuteMicrophones: When the pin is activated (0V), the microphones will be muted. When
deactivated (+ 12V), the microphones are unmuted.
Valuespace: <S: 0, 50>
Format: String with a maximum of 50 characters.
Example: GPIO Pin 1 Mode: InputNoAction
Example: H323 Profile 1 Authentication Password:
H323 Profile [1..1] Authentication Mode
Set the authentication mode.
Valuespace: <On/Off>
On: If the H.323 Gatekeeper Authentication Mode is set to On and a H.323 Gatekeeper indicates
that it requires authentication, the system will try to authenticate itself to the gatekeeper. Requires the
Authentication ID and Authentication Password to be defined on both the codec and the Gatekeeper.
Off: If the H.323 Gatekeeper Authentication Mode is set to Off the system will not try to authenticate
itself to a H.323 Gatekeeper, but will still try a normal registration.
Example: H323 Profile 1 Authentication Mode: Off
19
Download from Www.Somanuals.com. All Manuals Search And Download.
D14635.02—MARCH 2010
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Advanced config.
The H323 settings, cont...
H323 Profile [1..1] CallSetup Mode
The H323 settings, cont...
H323 Profile [1..1] H323Alias ID
The H.323 Call Setup Mode defines whether to use a Gatekeeper or Direct calling when establishing H323
calls.
Lets you specify the H.323 Alias ID which is used to address the system on a H.323 Gatekeeper and will
be displayed in the call lists. Example: “fi[email protected]”, “My H.323 Alias ID”
NOTE! Direct H.323 calls can be made even though the H.323 Call Setup Mode is set to Gatekeeper.
Valuespace: <S: 0, 49>
Valuespace: <Direct/Gatekeeper>
Format: String with a maximum of 49 characters
Direct: An IP-address must be used when dialling in order to make the H323 call.
Example: H323 Profile 1 H323Alias ID: “firstname.surname@company.com”
Gatekeeper: The system will use a Gatekeeper to make a H.323 call. When selecting this option the
H323 Profile Gatekeeper Address and H323 Profile Gatekeeper Discovery settings must also be
configured.
H323 Profile [1..1] PortAllocation
The H.323 Port Allocation setting affects the H.245 port numbers used for H.323 call signalling.
Example: H323 Profile 1 CallSetup Mode: Gatekeeper
Valuespace: <Dynamic/Static>
Dynamic: The system will allocate which ports to use when opening a TCP connection. The reason for
doing this is to avoid using the same ports for subsequent calls, as some firewalls consider this as a
sign of attack. When Dynamic is selected, the H.323 ports used are from 11000 to 20999. Once 20999
is reached they restart again at 11000. For RTP and RTCP media data, the system is using UDP ports
in the range 2326 to 2487. Each media channel is using two adjacent ports, ie 2330 and 2331 for RTP
and RTCP respectively. The ports are automatically selected by the system within the given range.
Firewall administrators should not try to deduce which ports are used when, as the allocation schema
within the mentioned range may change without any further notice.
H323 Profile [1..1] Gatekeeper Address
Specifies the IP address of the Gatekeeper. Requires the H.323 Call Setup Mode to be set to Gatekeeper
and the Gatekeeper Discovery to be set to Manual.
Valuespace: <S: 0, 255>
Format: String with a maximum of 255 characters.
Example: H323 Profile 1 Gatekeeper Address: “10.47.1.58”
Static: When set to Static the ports are given within a static predefined range [5555–6555].
Example: H323 Profile 1 PortAllocation: Dynamic
H323 Profile [1..1] Gatekeeper Discovery
Determines how the system shall register to a H.323 Gatekeeper.
Valuespace: <Manual/Auto>
Manual: The system will use a specific Gatekeeper identified by the Gatekeeper’s IP-address.
Auto: The system will automatically try to register to any available Gatekeeper. If a Gatekeeper
responds to the request sent from the codec within 30 seconds this specific Gatekeeper will be used.
This requires that the Gatekeeper is in auto discovery mode as well. If no Gatekeeper responds, the
system will not use a Gatekeeper for making H.323 calls and hence an IP-address must be specified
manually.
Example: H323 Profile 1 Gatekeeper Discovery: Manual
H323 Profile [1..1] H323Alias E164
The H.323 Alias E.164 defines the address of the system, according to the numbering plan implemented
in the H.323 Gatekeeper. The E.164 alias is equivalent to a telephone number, sometimes combined with
access codes.
Valuespace: <S: 0, 30>
Format: Compact string with a maximum of 30 characters. Valid characters are 0–9, * and #.
Example: H323 Profile 1 H323Alias E164: “90550092”
20
Download from Www.Somanuals.com. All Manuals Search And Download.
D14635.02—MARCH 2010
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Advanced config.
The Network settings
The Network settings, cont...
Network [1..1] IEEE8021X Eap Md5
Network [1..1] Assignment
Defines whether to use DHCP or Static IP assignment.
Message-Digest algorith 5. Is a Challenge Handshake Authentication Protocol that relies on a shared
secret. MD5 is a Weak security. EAP - Extensible Authentication Protocol. MD5 - Message Digest
Algorithm 5.
Changes to this setting requires a restart of the codec.
Valuespace: <Static/DHCP>
Valuespace: <On/Off>
Static: The IP Address, Subnet Mask and Default Gateway for the system must be specified in the
On: The EAP-MD5 protocol is enabled. Default mode is On.
Off: The EAP-MD5 protocol is disabled.
respective address fields.
DHCP: The system adresses are automatically assigend by the DHCP server.
Example: Network 1 IEEE8021X Eap Md5: On
Example: Network 1 Assignment: DHCP
Network [1..1] IEEE8021X Eap Peap
Network [1..1] DNS Domain Name
Protected Transport Layer Security. Developed by Microsoft, Cisco and RSA Security. Authenticates LAN
clients without the need for client certificates. EAP - Extensible Authentication Protocol. PEAP - Protected
Extensible Authentication Protocol.
DNS Domain Name is the default domain name suffix which is added to unqualified names.
Example: If the DNS Domain Name is “company.com” and the name to lookup is “MyVideoSystem”, this
will result in the DNS lookup “MyVideoSystem.company.com”.
Valuespace: <On/Off>
Valuespace: <S: 0, 64>
On: The EAP-PEAP protocol is enabled. Default mode is On.
Off: The EAP-PEAP protocol is disabled.
Format: String with a maximum of 64 characters.
Example: Network 1 DNS Domain Name: “company.com”
Example: Network 1 IEEE8021X Eap Peap: On
Network [1..1] DNS Server [1..5] Address
Defines the network addresses for DNS servers. Up to 5 addresses may be specified. If the network
addresses are unknown, contact your administrator or Internet Service Provider.
Network [1..1] IEEE8021X Eap TTLS
Tunneled Transport Layer Security. Developed by Funk Software and Certicom. Usually supported by
Agere Systems, Proxim and Avaya. Authenticates LAN clients without the need for client certificates. EAP -
Extensible Authentication Protocol. TTLS - Tunneled Transport Layer Security.
Valuespace: <S: 0, 64>
Format: String with a maximum of 64 characters.
Valuespace: <On/Off>
Example: Network 1 DNS Server 1 Address: “”
On: The EAP-TTLS protocol is enabled. Default mode is On.
Off: The EAP-TTLS protocol is disabled.
Network [1..1] IEEE8021X AnonymousIdentity
Example: Network 1 IEEE8021X Eap TTLS: On
The 802.1X Anonymous ID string is to be used as unencrypted identity with EAP types that support
different tunneled identity, like EAP-PEAP and EAP-TTLS. If set, the anonymous ID will be used for the
initial (unencrypted) EAP Identity Request.
Network [1..1] IEEE8021X Identity
The 802.1X Identity is the user name needed for 802.1X authentication.
Valuespace: <S: 0, 64>
Valuespace: <S: 0, 64>
Format: String with a maximum of 64 characters.
Format: String with a maximum of 64 characters.
Example: Network 1 IEEE8021X AnonymousIdentity: “”
Example: Network 1 IEEE8021X Identity: “”
21
Download from Www.Somanuals.com. All Manuals Search And Download.
D14635.02—MARCH 2010
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Advanced config.
The Network settings, cont...
Network [1..1] IEEE8021X Mode
The Network settings, cont...
Network [1..1] IPv4 QoS Mode
The system may be connected to an IEEE 802.1X LAN network with a port-based network access control
that is used to provide authenticated network access for Ethernet networks.
Defines whether IP Diffserv QoS should be used. The QoS (Quality of Service) is a method which
handles the priority of audio, video and data in the network. The QoS settings must be supported by the
infrastructure. DiffServ (Differentiated Services) is a computer networking architecture that specifies a
simple, scalable and coarse-grained mechanism for classifying, managing network traffic and providing
QoS priorities on modern IP networks.
Valuespace: <On/Off>
On: The 802.1X authentication is enabled.
Off: The 802.1X authentication is disabled. Default mode is Off.
Valuespace: <Off/Diffserv>
Example: Network 1 IEEE8021X Mode: Off
Off: When set to Off no QoS method is used.
Diffserv: Select Diffserv and then go to the Diffserv sub-menus (Audio, Data, Signalling and Video) to
configure these settings.
Network [1..1] IEEE8021X Password
Example: Network 1 IPv4 QoS Mode: diffserv
The 802.1X Password is the password needed for 802.1X authentication.
Valuespace: <S: 0, 32>
Network [1..1] IPv4 QoS Diffserv Audio
Format: String with a maximum of 32 characters.
The DiffServ Audio setting is used to define which priority Audio packets should have in an IP network.
Enter a priority, which ranges from 0 to 63 for the packets. The higher the number, the higher the priority.
These priorities might be overridden when packets are leaving the network controlled by the local network
administrator.
Example: Network 1 IEEE8021X Password: “***”
Network [1..1] IPv4 Address
Valuespace: <0..63>
Defines the Static IP address for the system. Only applicable if Static IP assignment is chosen.
Audio: A recommended value is DiffServ Code Point (DSCP) is AF41, which equals the value 34. If in
doubt, contact your network administrator.
Valuespace: <S: 0, 64>
Format: Compact string with a maximum of 64 characters.
Example: Network 1 IPv4 QoS Diffserv Audio: 0
Example: Network 1 IPv4 Address: “10.47.5.100”
Network [1..1] IPv4 QoS Diffserv Data
Network [1..1] IPv4 Gateway
Defines the IP default gateway. Only applicable if Static IP assignment is chosen.
The DiffServ Data setting is used to define which priority Data packets should have in an IP network.
Enter a priority, which ranges from 0 to 63 for the packets. The higher the number, the higher the priority.
These priorities might be overridden when packets are leaving the network controlled by the local network
administrator.
Valuespace: <S: 0, 64>
Format: Compact string with a maximum of 64 characters.
Valuespace: <0..63>
Example: Network 1 IPv4 Gateway: “10.47.5.100”
Data: A recommended value is DiffServ Code Point (DSCP) AF23, which equals the value 22. If in
doubt, contact your network administrator.
Network [1..1] IPv4 SubnetMask
Defines the IP subnet mask. Only applicable if Static IP assignment is chosen.
Example: Network 1 IPv4 QoS Diffserv Data: 0
Valuespace: <S: 0, 64>
Format: Compact string with a maximum of 64 characters.
Example: Network 1 IPv4 SubnetMask: “255.255.255.0”
22
Download from Www.Somanuals.com. All Manuals Search And Download.
D14635.02—MARCH 2010
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Advanced config.
The Network settings, cont...
Network [1..1] IPv4 QoS Diffserv Signalling
The Network settings, cont...
Network [1..1] TrafficControl Mode
The DiffServ Signalling setting is used to define which priority Signalling packets should have in an IP
Configure how video packets transmission speed shall be controlled.
network. Enter a priority, which ranges from 0 to 63 for the packets. The higher the number, the higher the
priority. These priorities might be overridden when packets are leaving the network controlled by the local
network administrator.
Valuespace: <On/Off>
On: Transmit video packets at maximum 20Mbps. Can be used to smooth out bursts in the outgoing
network traffic.
Valuespace: <0..63>
Off: Transmit video packets at link speed.
Signalling: A recommended value is DiffServ Code Point (DSCP) AF31 which equals the value 26. If in
Example: Network 1 TrafficControl: On
doubt, contact your network administrator.
Example: Network 1 IPv4 QoS Diffserv Signalling: 0
Network [1..1] IPv4 QoS Diffserv Video
The DiffServ Video setting is used to define which priority Video packets should have in an IP network.
Enter a priority, which ranges from 0 to 63 for the packets. The higher the number, the higher the priority.
These priorities might be overridden when packets are leaving the network controlled by the local network
administrator.
Valuespace: <0..63>
Video: A recommended value is DiffServ Code Point (DSCP) AF41, which equals the value 34. If in
doubt, contact your network administrator.
Example: Network 1 IPv4 QoS Diffserv Video: 0
Network [1..1] MTU
Set the ethernet MTU (Maximum Transmission Unit).
Valuespace: <400..1500>
Range: Select a value from 400 to 1500.
Example: Network 1 MTU: 1500
Network [1..1] Speed
Set the ethernet link speed.
Valuespace: <Auto/10half/10full/100half/100full/1000full>
Auto: Autonegotiate link speed.
10half: Force link to 10Mbps half-duplex.
10full: Force link to 10Mbps full-duplex.
100half: Force link to 100Mbps half-duplex.
100full: Force link to 100Mbps full-duplex.
1000full: Force link to 1Gbps full-duplex.
Example: Network 1 Speed: Auto
23
Download from Www.Somanuals.com. All Manuals Search And Download.
D14635.02—MARCH 2010
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Advanced config.
The NetworkServices settings
The NetworkServices settings, cont...
NetworkServices H323 Mode
NetworkServices NTP Address
Determines whether the system should be able to place and receive H.323 calls.
Enter the NTP Address to define the network time protocol server address. This address will be used if
NTP Mode is set to Manual, or if set to Auto and no address is supplied by a DHCP server.
NOTE! Changes in this setting requires the codec to be restarted.
Valuespace: <S: 0, 64>
Valuespace: <On/Off>
Format: String with a maximum of 64 characters.
On: Set to On to enable the possibility to place and receive H.323 calls.This is the default setting.
Off: Set to Off to disable the possibility to place and receive H.323 calls.
Example: NetworkServices NTP Address: “1.tandberg.pool.ntp.org”
Example: NetworkServices H323 Mode: On
NetworkServices NTP Mode
The Network Time Protocol (NTP) is used to synchronize the time of the system to a reference time server.
The time server will subsequently be queried every 24th hour for time updates. The time will be displayed
on the top of the screen. The system will use the time to timestamp messages transmitted to Gatekeepers
or Border Controllers requiring H.235 authentication. The system will use the time to timestamp messages
transmitted to Gatekeepers or Border Controllers that requires H.235 authentication. It is also used for
timestamping Placed Calls, Missed Calls and Received Calls.
NetworkServices HTTP Mode
HTTP is a web-interface for system management, call management such as call transfer, diagnostics and
software uploads.
Valuespace: <On/Off>
On: The HTTP protocol is enabled.
Off: The HTTP protocol is disabled.
Valuespace: <Auto/Manual>
Auto: The system will use the NTP server, by which address is supplied from the DHCP server in the
network. If no DHCP server is used, or the DHCP server does not provide the system with a NTP
server address, the system will use the static defined NTP server address specified by the user.
Example: NetworkServices HTTP Mode: On
Manual: The system will always use the static defined NTP server address specified by the user.
NetworkServices HTTPS Mode
HTTPS is a Web protocol that encrypts and decrypts user page requests as well as the pages that are
returned by the Web server.
Example: NetworkServices NTP Mode: Manual
Valuespace: <On/Off>
NetworkServices SIP Mode
Determines whether the system should be able to place and receive SIP calls.
On: The HTTPS protocol is enabled.
Off: The HTTPS protocol is disabled.
NOTE! Changes in this setting requires the codec to be restarted.
Example: NetworkServices HTTPS Mode: On
Valuespace: <On/Off>
On: Set to On to enable the possibility to place and receive SIP calls.This is the default setting.
Off: Set to Off to disable the possibility to place and receive SIP calls.
NetworkServices HTTPS VerifyServerCertificate
When the system connects to an external HTTPS server (like a phonebook server or an external manager),
this server will present a certificate to the system to identify itself. This setting tells the system if it should
verify that the certificate is signed by a trusted Certificate Authority (CA). This requires that list of trusted
CA’s is uploaded to the system in advance.
Example: NetworkServices SIP Mode: On
NetworkServices SNMP CommunityName
Valuespace: <On/Off>
Enter the name of the Network Services SNMP Community. SNMP Community names are used to
authenticate SNMP requests. SNMP requests must have a ‘password’ (case sensitive) in order to receive a
response from the SNMP Agent in the codec. The default password is “public”. If you have the TANDBERG
Management Suite (TMS) you must make sure the same SNMP Community is configured there too. Note!
The SNMP Community password is case sensitive.
On: Verify server certificates.
Off: Do not verify server certificates.
Example: NetworkServices HTTPS VerifyServerCertificate: Off
Valuespace: <S: 0, 50>
Format: String with a maximum of 50 characters.
Example: NetworkServices SNMP CommunityName: “public”
24
Download from Www.Somanuals.com. All Manuals Search And Download.
D14635.02—MARCH 2010
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Advanced config.
The NetworkServices settings, cont...
The NetworkServices settings, cont...
NetworkServices SNMP Host [1..3] Address
NetworkServices Telnet Mode
Enter the address of up to three SNMP Managers. All traps will then be sent to the hosts listed.
Telnet is a network protocol used on the Internet or local area network (LAN) connections.
The system’s SNMP Agent (in the codec) responds to requests from SNMP Managers (a PC program
etc.). SNMP Traps are generated by the SNMP Agent to inform the SNMP Manager about important
events. Can be used to send event created messages to the SNMP agent about different events like:
system reboot, system dialing, system disconnecting, MCU call, packet loss etc. Traps can be sent to
multiple SNMP Trap Hosts.
Valuespace: <On/Off>
On: The Telnet protocol is enabled.
Off: The Telnet protocol is disabled. This is the default factory setting.
Example: NetworkServices Telnet Mode: Off
Valuespace: <S: 0, 64>
Format: String with a maximum of 64 characters.
Example: NetworkServices SNMP Host 1 Address: “”
NetworkServices SNMP Mode
SNMP (Simple Network Management Protocol) is used in network management systems to monitor
network-attached devices (routers, servers, switches, projectors, etc) for conditions that warrant
administrative attention. SNMP exposes management data in the form of variables on the managed
The Phonebook settings
systems, which describe the system configuration. These variables can then be queried (set to ReadOnly)
and sometimes set (set to ReadWrite) by managing applications.
Phonebook Server [1..5] ID
Enter a name for the external phonebook.
Valuespace: <Off/ReadOnly/ReadWrite>
Valuespace: <S: 0, 64>
Off: Set to Off when you want to disable the SNMP network service.
ReadOnly: Set to ReadOnly when you want to enable the SNMP network service for queries only.
Format: String with a maximum of 64 characters.
Example: Phonebook Server 1 ID: “”
ReadWrite: Set to ReadOnly when you want to enable the SNMP network service for both queries and
commands.
Example: NetworkServices SNMP Mode: ReadWrite
Phonebook Server [1..5] URL
Enter the address (URL) to the external phonebook server.
NetworkServices SNMP SystemContact
Valuespace: <S: 0, 255>
Enter the name of the Network Services SNMP System Contact.
Format: String with a maximum of 255 characters.
Valuespace: <S: 0, 50>
Example: Phonebook Server 1 URL: “http://tms.company.com/tms/public/external/
phonebook/phonebook.asmx”
Format: String with a maximum of 50 characters.
Example: NetworkServices SNMP SystemContact: “”
NetworkServices SNMP SystemLocation
Enter the name of the Network Services SNMP System Location.
Valuespace: <S: 0, 50>
Format: String with a maximum of 50 characters.
Example: NetworkServices SNMP SystemLocation: “”
25
Download from Www.Somanuals.com. All Manuals Search And Download.
D14635.02—MARCH 2010
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Advanced config.
The Provisioning settings
The SerialPort settings
Provisioning ExternalManager Address
SerialPort BaudRate
Specifies the IP Address to the External Manager/Management system. If an External Manager address
and a path is configured, the system will post an HTTP message to this address when starting up.
When receiving this HTTP posting the External Manager (typically a management system) can return
configurations/commands to the unit as a result. If the DHCP Option 242 is returned in the DHCP
response from the DHCP server the system will interpret this as the External Manager address to use.
Specify the baud rate on the COM port (data port). The default value is 38400.
Other default parameters for the COM port are: Parity: None Databits: 8 Stopbits: 1 Flow control: None.
Valuespace: <9600/19200/38400/57600/115200>
Range: Select a baud rate from the baud rates listed (bps).
Valuespace: <S: 0, 64>
Example: SerialPort BaudRate: 38400
Format: String with a maximum of 64 characters.
Example: Provisioning ExternalManager Address: “”
SerialPort LoginRequired
The Serial Login setting determines whether or not there should be a login when connecting to the COM
port (data port).
Provisioning ExternalManager Path
Valuespace: <On/Off>
Specifies the path to the External Manager/Management system. If an External Manager address
and a path is configured, the system will post an HTTP message to this address when starting up.
When receiving this HTTP posting the External Manager (typically a management system) can return
configurations/commands to the unit as a result. If the DHCP Option 242 is returned in the DHCP
response from the DHCP server the system will interpret this as the External Manager address to use.
On: Login is required when connecting to the COM port (data port).
Off: The user can access the COM port (data port) without any login.
Example: SerialPort LoginRequired: On
Valuespace: <S: 0, 255>
Format: String with a maximum of 255 characters.
Example: Provisioning ExternalManager Path: “tms/public/external/management/
SystemManagementService.asmx”
Provisioning ExternalManager Protocol
Determines whether or not to use secure management.
Valuespace: <HTTP/HTTPS>
HTTP: Set to HTTP to disable secure management. Requires HTTP to be enabled in the Network
Services HTTP Mode setting.
HTTPS: Set to HTTPS to enable secure management. Requires HTTPS to be enabled in the Network
Services HTTPS Mode setting.
Example: Provisioning ExternalManager Protocol: http
Provisioning Mode
Provides the possibility of managing the codec (endpoint) by using an external manager/management
system.
Valuespace: <Off/TMS>
Off: The system will not try to register to any management system.
TMS: If set to TMS the system will try to register with a TMS server as described in Provisioning
ExternalManager settings. TMS is short for TANDBERG Management System. Contact your
TANDBERG representative for more information.
Example: Provisioning Mode: TMS
26
Download from Www.Somanuals.com. All Manuals Search And Download.
D14635.02—MARCH 2010
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Advanced config.
The SIP settings
The SIP settings, cont...
SIP Profile [1..1] Proxy [1..4] Address
SIP Profile [1..1] Authentication [1..1] LoginName
This is the user name part of the credentials used to authenticate towards the SIP proxy.
The Proxy Address is the manually configured address for the outbound proxy. It is possible to use a fully
qualified domain name, or an IP address. The default port is 5060 for TCP and UDP but another one can
be provided. If Outbound is enabled, multiple proxies can be addressed.
Valuespace: <S: 0, 50>
Format: String with a maximum of 50 characters.
Valuespace: <S: 0, 255>
Example: SIP Profile 1 Authentication 1 LoginName: “”
Format: Compact string with a maximum of 255 characters.
Example: SIP Profile 1 Proxy 1 Address: “”
SIP Profile [1..1] Authentication [1..1] Password
This is the password part of the credentials used to authenticate towards the SIP proxy.
SIP Profile [1..1] Proxy [1..4] Discovery
Set the SIP Proxy server discovery to auto or manual.
Valuespace: <S: 0, 50>
Format: String with a maximum of 50 characters.
Valuespace: <Auto/Manual>
Example: SIP Profile 1 Authentication 1 Password:
Manual: When Manual is selected, the manually configured SIP Proxy address will be used
Auto: When Auto is selected, the SIP Proxy address is obtained using Dynamic Host Configuration
Protocol (DHCP).
SIP Profile [1..1] DefaultTransport
Select the transport protocol to be used over the LAN.
Example: SIP Profile 1 Proxy 1 Discovery: Manual
Valuespace: <UDP/TCP/TLS/Auto>
UDP: The system will always use UDP as the default transport method.
TCP: The system will always use TCP as the default transport method.
SIP Profile [1..1] Type
Enables SIP extensions and special behaviour for a vendor or provider
TLS: The system will always use TLS as the default transport method. For TLS connections a SIP
CA-list can be uploaded using the web interface. If no such CA-list is available on the system then
anonymous Diffie Hellman will be used.
Valuespace: <Standard/Alcatel/Avaya/Cisco/Microsoft/Nortel/Experimental/Siemens>
Standard: Should be used when registering to standard SIP proxy like OpenSer.
Alcatel: Must be used when registering to a Alcatel-Lucent OmniPCX Enterprise R7 or later.
Avaya: Must be used when registered to a Avaya Communication Manager.
Auto: The system will try to connect using transport protocols in the following order: TLS, TCP, UDP.
Example: SIP Profile 1 DefaultTransport: Auto
Cisco: Must be used when registering to a Cisco CallManager version 5 or later.
Microsoft: Must be used when registering to a Microsoft LCS or OCS server.
Nortel: Must be used when registering to a Nortel MCS 5100 or MCS 5200 PBX.
Experimental: Can be used if auto is not working Note! This mode is for testing purposes only.
SIP Profile [1..1] Outbound
The client initiated connections mechanism for firewall traversal, connection reuse and redundancy. The
Example: SIP Profile 1 Type: Standard
Valuespace: <On/Off>
On: Set up multiple outbound connections to servers in the Proxy Address list.
Off: Connect to the single proxy configured first in Proxy Address list.
SIP Profile [1..1] URI
The SIP URI or number is used to address the system. This is the URI that is registered and used by the
SIP services to route inbound calls to the system. A Uniform Resource Identifier (URI) is a compact string
of characters used to identify or name a resource.
Example: SIP Profile 1 Outbound: Off
Valuespace: <S: 0, 255>
Format: Compact string with a maximum of 255 characters.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
D14635.02—MARCH 2010
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Advanced config.
The Standby settings
The Standby settings, cont...
Standby BootAction
Standby WakeupAction
Decide what the system is going to do on boot.
Decide what the system is going to do when leaving standby mode.
Valuespace: <None/Preset1/Preset2/Preset3/Preset4/Preset5/Preset6/Preset7/Preset8/
Valuespace: <None/Preset1/Preset2/Preset3/Preset4/Preset5/Preset6/Preset7/Preset8/
Preset9/Preset10/Preset11/Preset12/Preset13/Preset14/Preset15/RestoreCameraPosition/
DefaultCameraPosition>
Preset9/Preset10/Preset11/Preset12/Preset13/Preset14/Preset15/RestoreCameraPosition/
DefaultCameraPosition>
None: No action.
None: No action.
Preset 1..15: Activate the selected preset.
Preset 1..15: Activate the selected preset.
RestoreCameraPosition: Set the camera to the position it had before the last boot.
DefaultCameraPosition: Set the camera to the factory default position.
RestoreCameraPosition: Set the camera to the position it had before entering standby.
DefaultCameraPosition: Set the camera to the factory default position.
Example: Standby BootAction: DefaultCameraPosition
Example: Standby WakeupAction: RestoreCameraPosition
Standby Control
Determine whether the system should go into standby mode or not.
Valuespace: <On/Off>
On: Enter standby mode when the Standby Delay has timed out. Requires the Standby Delay to be set
to an appropriate value.
Off: Not entering standby mode.
Example: Standby Control: On
Standby Delay
Define how long (in minutes) the system shall be in idle mode before it goes into standby mode. Requires
the Standby Control to be enabled.
Valuespace: <1..480>
Range: 1-480 minutes
Example: Standby Delay: 10
Standby StandbyAction
NEW TC2.1 Decide what the system is going to do when going into standby mode.
Valuespace: <None/PrivacyPosition>
None: No action.
PrivacyPosition: Turns the camera to a sideways position for privacy.
Example: Standby StandbyAction: PrivacyPosition
28
Download from Www.Somanuals.com. All Manuals Search And Download.
D14635.02—MARCH 2010
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Advanced config.
The SystemUnit settings
The Time settings
SystemUnit CallLogging Mode
Time DateFormat
Enables/disables logging of calls received or placed by the system. The call logs may then be viewed via
the GUI or using the xHistory command.
Specifies the date format.
Valuespace: <DD_MM_YY/MM_DD_YY/YY_MM_DD>
Valuespace: <On/Off>
On: Enable logging.
Off: Disable logging.
DD_MM_YY: The date January 30th 2009 will be displayed: 30.01.09
MM_DD_YY: The date January 30th 2009 will be displayed: 01.30.09
YY_MM_DD: The date January 30th 2009 will be displayed: 09.01.30
Example: SystemUnit CallLogging Mode: On
Example: Time DateFormat: DD_MM_YY
SystemUnit IrSensor Mode
Time TimeFormat
Specifies the time format.
The System Unit IR Sensor setting determines whether the infrared receiver on the codec should be
enabled or not. The IR sensor LED is located in the front of the codec and flickers when an ir signal is
received from the remote control.
Valuespace: <24H/12H>
24H: Set the time format to 24 hours.
12H: Set the time format to 12 hours (AM/PM).
Valuespace: <On/Off/Auto>
On: Set to On to enable the IR sensor on the codec.
Off: Set to Off to disable the IR sensor on the codec.
Example: Time TimeFormat: 24H
Auto: The system will automatically disable the IR sensor on the codec if the IR sensor at camera is
enabled. Otherwise the IR sensor on the codec will be enabled.
Example: SystemUnit IrSensor Mode: On
SystemUnit MenuLanguage
The setting is used to select the language for the GUI (Graphical User Interface).
Valuespace: <English/Norwegian/Swedish/German/French/Italian/Japanese/Russian/Spanish/Korean/
Finnish/ChineseSimplified/ChineseTraditional/PortugueseBrazilian/Turkish/Polish>
Example: SystemUnit MenuLanguage: English
SystemUnit Name
Enter a System Name to define a name of the system unit. If the H.323 Alias ID is configured on the system
then this ID will be used instead of the system name. The system name will be displayed:
* When the codec is acting as an SNMP Agent
* Towards a DHCP server
Valuespace: <S: 0, 50>
Format: String with a maximum of 50 characters.
Example: SystemUnit Name: “Meeting Room Name”
29
Download from Www.Somanuals.com. All Manuals Search And Download.
D14635.02—MARCH 2010
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Advanced config.
The Time settings, cont...
The Video settings
Time Zone
Video DefaultPresentationSource
Specifies the time zone where the system is located, using Windows time zone description format.
Define which video input source shall be used as the default presentation source (e.g. when you press the
Presentation key on the remote control). The input source is configured to a video input connector. See
the Video Input Matrix table at the back of the codec and the description of the Video Input Matrix in the
Interfaces section.
Valuespace: <GMT-12:00 (International Date Line West)/GMT-11:00 (Midway Island, Samoa)/GMT-10:00
(Hawaii)/GMT-09:00 (Alaska)/GMT-08:00 (Pacific Time (US & Canada) Tijuana)/GMT-07:00 (Arizona)/
GMT-07:00 (Mountain Time (US & Canada))/GMT-07:00 (Chihuahua, La Paz, Mazatlan)/GMT-06:00
(Central America)/GMT-06:00 (Saskatchewan)/GMT-06:00 (Guadalajara, Mexico City, Monterrey)/GMT-
06:00 (Central Time (US & Canada))/GMT-05:00 (Indiana (East))/GMT-05:00 (Bogota, Lima, Quito)/
GMT-05:00 (Eastern Time (US & Canada))/GMT-04:30 (Caracas)/GMT-04:00 (La Paz)/GMT-04:00
(Santiago)/GMT-04:00 (Atlantic Time (Canada))/GMT-03:30 (Newfoundland)/GMT-03:00 (Buenos Aires,
Georgetown)/GMT-03:00 (Greenland)/GMT-03:00 (Brasilia)/GMT-02:00 (Mid-Atlantic)/GMT-01:00 (Cape
Verde Is.)/GMT-01:00 (Azores)/GMT (Casablanca, Monrovia)/GMT (Greenwich Mean Time : Dublin,
Edinburgh, Lisbon, London)/GMT+01:00 (West Central Africa)/GMT+01:00 (Amsterdam, Berlin, Bern,
Rome, Stockholm, Vienna)/GMT+01:00 (Brussels, Copenhagen, Madrid, Paris)/GMT+01:00 (Sarajevo,
Skopje, Warsaw, Zagreb)/GMT+01:00 (Belgrade, Bratislava, Budapest, Ljubljana, Prague)/GMT+02:00
(Harare, Pretoria)/GMT+02:00 (Jerusalem)/GMT+02:00 (Athens, Istanbul, Minsk)/GMT+02:00 (Helsinki,
Kyiv, Riga, Sofia, Tallinn, Vilnius)/GMT+02:00 (Cairo)/GMT+02:00 (Bucharest)/GMT+03:00 (Nairobi)/
GMT+03:00 (Kuwait, Riyadh)/GMT+03:00 (Moscow, St. Petersburg, Volgograd)/GMT+03:00 (Baghdad)/
GMT+03:30 (Tehran)/GMT+04:00 (Abu Dhabi, Muscat)/GMT+04:00 (Baku, Tbilisi, Yerevan)/GMT+04:30
(Kabul)/GMT+05:00 (Islamabad, Karachi, Tashkent)/GMT+05:00 (Ekaterinburg)/GMT+05:30 (Chennai,
Kolkata, Mumbai, New Delhi)/GMT+05:45 (Kathmandu)/GMT+06:00 (Sri Jayawardenepura)/GMT+06:00
(Astana, Dhaka)/GMT+06:00 (Almaty, Novosibirsk)/GMT+06:30 (Rangoon)/GMT+07:00 (Bangkok,
Hanoi, Jakarta)/GMT+07:00 (Krasnoyarsk)/GMT+08:00 (Perth)/GMT+08:00 (Taipei)/GMT+08:00 (Kuala
Lumpur, Singapore)/GMT+08:00 (Beijing, Chongqing, Hong Kong, Urumqi)/GMT+08:00 (Irkutsk, Ulaan
Bataar)/GMT+09:00 (Osaka, Sapporo, Tokyo)/GMT+09:00 (Seoul)/GMT+09:00 (Yakutsk)/GMT+09:30
(Darwin)/GMT+09:30 (Adelaide)/GMT+10:00 (Guam, Port Moresby)/GMT+10:00 (Brisbane)/GMT+10:00
(Vladivostok)/GMT+10:00 (Hobart)/GMT+10:00 (Canberra, Melbourne, Sydney)/GMT+11:00 (Magadan,
Solomon Is., New Caledonia)/GMT+12:00 (Fiji, Kamchatka, Marshall Is.)/GMT+12:00 (Auckland,
Wellington)/GMT+13:00 (Nuku alofa)>
Valuespace: <1..5>
Range: Select one of the five presentation sources
Example: Video DefaultPresentationSource: 3
Video Input DVI [3, 5] Type
The official DVI standard supports both digital and analog signals. In most cases the default AutoDetect
setting can detect whether the signal is analog RGB or digital. However, in some rare cases when DVI-I
cables are used (these cables can carry both the analog and digital signals) this detection might fail. This
setting makes it possible to override the AutoDetect and select the correct DVI video input. This setting
should also be used if the video input is an analog component (YPbPr) type signal. This is used by some
cameras (Sony EVI-HD1) and DVD/Blu-ray players. Since it is not possible to auto detect the difference
between AnalogRGB and AnalogYPbPr, the Analog YPbPr setting has to be selected.
Valuespace: <AutoDetect/Digital/AnalogRGB/AnalogYPbPr>
AutoDetect: Set to AutoDetect to automatically detect if the signal is analog RGB or digital.
Digital: Set to Digital to force the DVI video input to Digital when using DVI-I cables with both analog
and digital pins and AutoDetect fails.
AnalogRGB: Set to AnalogRGB to force the DVI video input to AnalogRGB when using DVI-I cables
with both analog and digital pins and AutoDetect fails.
AnalogYPbPr: Set to AnalogYPbPr to force the DVI video input to AnalogYPbPr, as the component
(YPbPr) signal cannot be auto detected.
Example: Video Input DVI 3 Type: AutoDetect
Example: Time Zone: “GMT (Greenwich Mean Time : Dublin, Edinburgh, Lisbon,
London)”
Video Input Source [1..5] CameraControl CameraId
Select the ID of the camera in the Visca chain that is connected to this camera source. The CameraId
setting represents the camera’s position in the Visca chain.
Cascaded cameras and Visca commands are described in the PrecisionHD 1080p User Guide. The user
Valuespace: <1..5>
Example: Video Input Source 1 CameraControl CameraId: 1
30
Download from Www.Somanuals.com. All Manuals Search And Download.
D14635.02—MARCH 2010
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Advanced config.
The Video settings, cont...
Video Input Source [1..5] CameraControl Mode
The Video settings, cont...
Video Input Source [4] Connector
Determines whether or not the camera control should be enabled for the selected video input source.
Select which video input connector to be active on connector group 4. The available options for Source 4
are listed below.
Valuespace: <On/Off>
Valuespace: <HDMI/HDSDI>
On: Set to On to enable camera control for the camera connected to the selected video input
connector.
HDMI: Select HDMI when you want to use the HDMI 4 connector as input.
HDSDI: Select HD-SDI when you want to use the HD-SDI 4 connector as input.
Off: Set to Off to disable camera control for the camera connected to the selected video input
connector.
Example: Video Input Source 4 Connector: HDMI
Example: Video Input Source 1 CameraControl Mode: On
Video Input Source [5] Connector
Select which video input connector to be active on connector group 5. The available options for Source 5
are listed below.
Video Input Source [1] Connector
Select which video input connector to be active on connector group 1. The available options for Source 1
are listed below.
Valuespace: <YC/Composite/DVI>
Valuespace: <HDMI/HDSDI/YPbPr>
DVI: Select DVI-I when you want to use the DVI-I 5 connector as input.
HDMI: Select HDMI when you want to use the HDMI 1 connector as input.
HDSDI: Select HD-SDI when you want to use the HD-SDI 1 connector as input.
YPbPr: Select YPbPr when you want to use the Y-Pb-Pr (Component) 1 connectors as input.
YC: Select YC when you want to use the S-Video (YC) input. Connect the S-Video input to the
connector marked as Y/Comp and C.
Composite: Select Comp when you want to use the Composite input. Connect the Composite input to
the connector marked as Y/Comp.
Example: Video Input Source 1 Connector: HDMI
Example: Video Input Source 5 Connector: DVI
Video Input Source [2] Connector
Select which video input connector to be active on connector group 2. The available options for Source 2
are listed below.
Video Input Source [1..5] Name
Customizable name of the connector group. Enter the name of the video input source 1-5.
Valuespace: <HDMI/HDSDI/YPbPr>
Valuespace: <S: 0, 50>
HDMI: Select HDMI when you want to use the HDMI 2 connector as input.
HDSDI: Select HD-SDI when you want to use the HD-SDI 2 connector as input.
YPbPr: Select YPbPr when you want to use the Y-Pb-Pr (Component) 2 connectors as input.
Format: String with a maximum of 50 characters.
Example: Video Input Source 1 Name: “”
Example: Video Input Source 2 Connector: HDMI
Video Input Source [3] Connector
Select which video input connector to be active on connector group 3. The available options for Source 3
are listed below.
Valuespace: <HDMI/HDSDI/DVI>
DVI: Select DVI-I when you want to use the DVI-I 3 connector as input.
HDMI: Select HDMI when you want to use the HDMI 3 connector as input.
HDSDI: Select HD-SDI when you want to use the HD-SDI 3 connector as input.
Example: Video Input Source 3 Connector: DVI
31
Download from Www.Somanuals.com. All Manuals Search And Download.
D14635.02—MARCH 2010
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Advanced config.
The Video settings, cont...
Video Input Source [1..5] OptimalDefinition Profile
The Video settings, cont...
Video Input Source [1..5] OptimalDefinition Threshold60fps
The system will automatically choose what resolution and framerate to transmit based on input resolution/
framerate, available bandwidth and wether ths source is configured for motion or sharpness. For motion
sources, this setting can be used to adjust how rapidly the system should increase the transmitted
resolution when increasing bandwidth. For instance, if the source is a camera input is 1920x1080p60, the
system will transmit 1920x720p60 at about 2.2Mb/sec and above with this setting set to normal, but will
will transmit 1920x720p60 at about 1.1Mb/sec and above with this setting set to high. In general you could
choose medium or high if you have good quality video inputs and good lighting conditions, while normal
would give a good experience in most conditions, including not optimal lighting.
For each video input, this setting tells the system the lowest resolution where it should transmit 60fps. So
for all resolutions lower than this, the maximum transmitted framerate would be 30fps, while above this
resolution 60fps would also be possible, if the available bandwidth is adequate.
Valuespace: <512_288/768_448/1024_576/1280_720/Never>
512_288: Set the threshold to 512x288.
768_448: Set the threshold to 768x448.
1024_576: Set the threshold to 1024x576.
Valuespace: <Normal/Medium/High>
1280_720: Set the threshold to 1280x720.
See Table 1: Optimal definition for systems supporting 1080p and Table 2: Optimal definition for
systems supporting 720p60.
Never: Do not set a threshold for transmitting 60fps.
Example: Video Input Source 1 OptimalDefinition Threshold60fps: 1280_720
Example: Video Input Source 1 OptimalDefinition Profile: Normal
Video Input Source [1..5] Quality
When encoding and transmitting video there will be a tradeoff between high resolution and high framerate.
For some video sources it is more important to transmit high framerate than high resolution and vice versa.
The Quality setting specifies whether to give priority to high frame rate or to high resolution for a given
source.
Table 1: Optimal definition, for systems supporting 1080p
w288p30
256kbit/s
128kbit/s
128kbit/s
w448p30
w576p30
720p30
1080p30
Valuespace: <Motion/Sharpness>
Normal
Medium
High
512 kbit/s
384 kbit/s
256 kbit/s
768 kbit/s
512 kbit/s
512 kbit/s
1152 kbit/s
768 kbit/s
768 kbit/s
2560 kbit/s
1920 kbit/s
1472 kbit/s
Motion: Gives the highest possible framerate. Used when there is a need for higher frame rates,
typically when a large number of participants are present or when there is a lot of motion in the picture.
Sharpness: Gives the highest possible resolution. Used when you want the highest quality of detailed
images and graphics.
Example: Video Input Source 1 Quality: Motion
Table 2: Optimal definition, for systems supporting 720p60
w144p60
128kbit/s
128kbit/s
128kbit/s
w288p60
w448p60
w576p60
720p60
Video Layout ScaleToFrame
Defines what to do if the aspect ratio of a video input source doesn’t match the aspect ratio of the
corresponding image frame in a composition. For example if you have a 4:3 input source (like XGA) to be
displayed on a 16:9 output (like HD720).
Normal
Medium
High
512 kbit/s
384 kbit/s
256 kbit/s
1152 kbit/s
768 kbit/s
512 kbit/s
1472 kbit/s
1152 kbit/s
768 kbit/s
2240 kbit/s
1472 kbit/s
1152 kbit/s
Valuespace: <Manual/MaintainAspectRatio/StretchToFit>
Manual: If the difference in aspect ratio between the video input source and the target image frame is
less than the ScaleToFrameThrshold configuration (in percent), the image is stretched to fit. Unless the
system will maintain the original aspect ratio.
MaintainAspectRatio: Will maintain the aspect ratio of the input source, and fill in black in the rest of the
frame (letter boxing or pillar boxing).
StretchToFit: Will stretch (horizontally or vertically) the input source to fit into the image frame.
Example: Video Layout ScaleToFrame: MaintainAspectRatio
32
Download from Www.Somanuals.com. All Manuals Search And Download.
D14635.02—MARCH 2010
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Advanced config.
The Video settings, cont...
Video Layout ScaleToFrameTreshold
The Video settings, cont...
Video OSD InputMethod InputLanguage
Only applicable if the ScaleToFrame configuration is set to manual. If the difference in aspect ratio between
the video input source and the target image frame is less than the ScaleToFrameThrshold configuration (in
percent), the image is stretched to fit. Unless the system will maintain the original aspect ratio.
The codec can be enabled for Cyrillic input characters in the GUI (Graphical User Interface). NOTE:
Requires that Video OSD inputMethod Cyrillic is set to On.
Valuespace: <Latin/Cyrillic>
Valuespace: <0..100>
Latin: Latin characters can be entered when using the remote control (default setting).
Range: Select a value from 0 to 100 percent.
Cyrillic characters can be entered using the remote control. NOTE: Requires a TANDBERG Remote
Control TRC5 with Cyrillic fonts.
Example: Video Layout ScaleToFrameTreshold: 5
Example: Video OSD InputMethod InputLanguage: Latin
Video Layout Scaling
Defines whether the system should automatically adjust aspect ratio for images or frames when it differs
between the image and the frame it is to be placed in.
Video OSD InputMethod Cyrillic
This configuration is used to hide or show the Cyrillic mode as menu input language in the GUI (Graphical
User Interface).
Valuespace: <On/Off>
On: Let the system automatically adjust aspect ratio.
Off: Do not do any aspect ratio changes automatically.
Valuespace: <On/Off>
On: Cyrillic mode is available as a menu input language in the GUI. This will enable the setting Video
OSD InputMethod InputLanguage.
Example: Video Layout Scaling: On
Off: Cyrillic mode is NOT available as a menu input language in the GUI.
Example: Video OSD InputMethod Cyrillic: Off
Video MainVideoSource
Define which video input source shall be used as the main video source. The input source is configured to
a video input connector. See the Video Input Matrix table at the back of the codec and the description of
the Video Input Matrix in the Interfaces section.
Video OSD Mode
The Video OSD (On Screen Display) Mode lets you define whether or not information and icons on screen
should be displayed.
Valuespace: <1..5>
Range: Select one of the five video sources
Valuespace: <On/Off>
On: Set to On to display the on screen menus, icons and indicators.
Off: Set to Off to hide the on screen menus, icons and indicators.
Example: Video MainVideoSource: 1
Example: Video OSD Mode: On
Video Monitors
The codec can be used with more than one monitor and this setting lets you set the codec’s monitor
layout mode to single, dual, presentation only on the dual monitor, or quadruple.
Video OSD Output
Valuespace: <Single/Dual/DualPresentationOnly/Quadruple>
Single: The same layout is shown on all monitors.
Dual: The layout is distributed on two monitors.
The Video OSD (On Screen Display) Output lets you define which monitor should display the on screen
menus, information and icons. By default the OSD output is displayed on the first monitor.
If you have a single monitor and you cannot see any OSD on the monitor: If the OSD output has been
set to the second monitor and the second monitor is not connected, then you cannot see any menus,
information or icons on the screen. To move the OSD output to the first monitor press the following
shortcut sequence on the remote control. Press the Disconnect key followed by: * # * # 0 x # (where x is
output 1 to 4).
DualPresentationOnly: All participants in the call will be shown on the first monitr, while the presentation
(if any) will be shown on the second monitor.
Quadruple: The layout is distributed on four monitors, so that each remote participant and the
presentation will be shown on separate monitors
Valuespace: <1..4>
Example: Video Monitors: Single
Range: Select 1 for HDMI 1 output, select 2 for DVI-I 2 output, select 3 for HDMI 3 output, or select 4
for DVI-I 4 output.
Example: Video OSD Output: 1
33
Download from Www.Somanuals.com. All Manuals Search And Download.
D14635.02—MARCH 2010
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Advanced config.
The Video settings, cont...
Video OSD TodaysBookings
The Video settings, cont...
Video Output HDMI [1, 3] Resolution
This setting can be used to display the systems bookings for today on the main OSD menu. This requires
that the system is bookable by an external booking system, like TMS (TANDBERG Management Suite).
Select the preferred resolution for the monitor connected to HDMI video output. This will force the selected
resolution on the monitor.
Valuespace: <On/Off>
Valuespace: <Auto/640_480_60/800_600_60/1024_768_60/1280_1024_60/1280_720_60/1920_1080_6
0/1280_768_60/1360_768_60/1366_768_60/1600_1200_60/1920_1200_60>
On: Displays information about this systems bookings on screen.
Off: Do not display todays bookings.
Auto: The system will automatically try to set the optimal resolution based on negotiation with the
connected monitor.
Example: Video OSD TodaysBookings: Off
Range: 640x480@60p, 800x600@60p, 1024x768@60p, 1280x1024@60p, 1280x720@60p,
1920x1080@60p, 1280x768@60p, 1360x768@60p, 1366x768@60p, 1600x1200@60p,
1920x1200@60p
Video Output HDMI [1, 3] MonitorRole
Example: Video Output HDMI 1 Resolution: 1920_1080_60
The monitor role describes what video stream will be shown on the monitor connected to the output
connector. Applicable only if the monitor configuration is set to dual or quadruple.
Valuespace: <First/Second/PresentationOnly/Third/Fourth>
First: Show main video stream.
Video Output DVI [2, 4] MonitorRole
The monitor role describes what video stream will be shown on the monitor connected to the output
connector. Applicable only if the monitor configuration is set to dual or quadruple.
Second: Show presentation video stream if active, or other participants.
PresentationOnly: Show presentation video stream if active, and nothing else.
Third: Use for remote participants (only for quadruple monitor setup).
Fourth: Use for remote participants (only for quadruple monitor setup).
Valuespace: <First/Second/PresentationOnly/Third/Fourth>
First: Show main video stream.
Second: Show presentation video stream if active, or other participants.
PresentationOnly: Show presentation video stream if active, and nothing else.
Third: Use for remote participants (only for quadruple monitor setup).
Fourth: Use for remote participants (only for quadruple monitor setup).
Example: Video Output HDMI 1 MonitorRole: First
Video Output HDMI [1, 3] OverscanLevel
Example: Video Output DVI 4 MonitorRole: First
Some TV’s or other monitors may not display the whole image sent out on the systems video output, but
cuts the outer parts of the image. In this case this setting can be used to let the system not use the outer
parts of video resolution. Both the video and the OSD menu will be scaled in this case.
Video Output DVI [2, 4] OverscanLevel
Valuespace: <Medium/High/None>
Some TV’s or other monitors may not display the whole image sent out on the systems video output, but
cuts the outer parts of the image. In this case this setting can be used to let the system not use the outer
parts of video resolution. Both the video and the OSD menu will be scaled in this case.
Medium: The system will not use the outer 3% of the output resolution.
High: The system will not use the outer 6% of the output resolution
None: The system will use all of the output resolution.
Valuespace: <Medium/High/None>
Medium: The system will not use the outer 3% of the output resolution.
High: The system will not use the outer 6% of the output resolution
None: The system will use all of the output resolution.
Example: Video Output HDMI 1 OverscanLevel: None
Example: Video Output DVI 2 OverscanLevel: None
34
Download from Www.Somanuals.com. All Manuals Search And Download.
D14635.02—MARCH 2010
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Advanced config.
The Video settings, cont...
Video Output DVI [2, 4] Resolution
The Video settings, cont...
Video Output Composite [5] Resolution
Select the preferred resolution for the monitor connected to video output DVI-I 2 or 4. This will force the
selected resolution on the monitor.
Select the preferred resolution for the monitor connected to video output composite 1. This will force the
selected resolution on the monitor.
Valuespace: <Auto/640_480_60/800_600_60/1024_768_60/1280_1024_60/1280_720_60/1920_1080_6
0/1280_768_60/1360_768_60/1366_768_60/1600_1200_60/1920_1200_60>
Valuespace: <PAL/NTSC>
Range: Select PAL or NTSC resolution.
Auto: The system will automatically try to set the optimal resolution based on negotiation with the
connected monitor.
Example: Video Output Composite 5 Resolution: NTSC
Range: 640x480@60p, 800x600@60p, 1024x768@60p, 1280x1024@60p, 1280x720@60p,
1920x1080@60p, 1280x768@60p, 1360x768@60p, 1366x768@60p, 1600x1200@60p,
1920x1200@60p
Video Selfview
The Video Selfview setting determines whether or not the main video source (selfview) should be displayed
on screen.
Example: Video Output DVI 2 Resolution: 1920_1080_60
Valuespace: <On/Off>
On: Set to On when you want selfview to be displayed on screen.
Off: Set to Off when you do not want selfview to be displayed on screen.
Video Output Composite [5] MonitorRole
The monitor role describes what video stream will be shown on the monitor connected to the output
connector. Applicable only if the monitor configuration is set to dual or quadruple.
Example: Video Selfview: On
Valuespace: <First/Second/PresentationOnly/Third/Fourth>
First: Show main video stream.
Video WallPaper
Second: Show presentation video stream if active, or other participants.
PresentationOnly: Show presentation video stream if active, and nothing else.
Third: Use for remote participants (only for quadruple monitor setup).
Fourth: Use for remote participants (only for quadruple monitor setup).
The Video Wallpaper setting determines whether or not a background picture should be displayed on
screen when idle.
Valuespace: <None/Growing/Summersky/Custom>
None: Set to None if you do not want a wallpaper to be displayed on screen.
Summersky, Growing: Select the wallpaper to be displayed on screen.
Example: Video Output Composite 5 MonitorRole: First
Custom: The custom wallpaper is uploaded from the web interface. Open a web browser and enter
the IP address of the codec. Select “Wallpaper” from the menu on top of the screen. Browse for the
file and press the “Upload” button. Toggle once between “None” and “Custom” wallpaper to make the
change take effect. See the Appendices section for further details about the web interface.
Video Output Composite [5] OverscanLevel
Some TV’s or other monitors may not display the whole image sent out on the systems video output, but
cuts the outer parts of the image. In this case this setting can be used to let the system not use the outer
parts of video resolution. Both the video and the OSD menu will be scaled in this case.
Example: Video Wallpaper: Summersky
Valuespace: <Medium/High/None>
Medium: The system will not use the outer 3% of the output resolution.
High: The system will not use the outer 6% of the output resolution
None: The system will use all of the output resolution.
Example: Video Output Composite 5 OverscanLevel: None
35
Download from Www.Somanuals.com. All Manuals Search And Download.
D14635.02—MARCH 2010
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Advanced config.
The Experimental menu
The Advanced configurations menu has an option called Experimental. The settings within this menu
can be used ‘as is’ and will not be further documented. NOTE! The Experimenal menu WILL change.
The Experimantal menu, cont...
Experimental CustomSoftbuttons State [1..2] Softbutton [1..5] Type
The Experimental settings can be used ‘as is’ and will not be further documented. NOTE: The
Experimental settings WILL change.
Experimental Audio Input Microphone [1..8] Channel
The Experimental settings can be used ‘as is’. NOTE: The Experimental settings WILL change.
Valuespace: <NotSet/MainSource/PresentationSource/CameraPreset/Actions/SpeedDial>
Example: Experimental CustomSoftbuttons State 1 Softbutton 1 Type: NotSet
Defines whether the microphone signal is a mono signal or part of a multichannel signal.
Valuespace: <Left/Right/Mono>
Experimental CustomSoftbuttons State [1..2] Softbutton [1..5] Value
The Experimental settings can be used ‘as is’ and will not be further documented. NOTE: The
Experimental settings WILL change.
Left: The microphone signal is the left channel of a stereo signal.
Right: The microphone signal is the right channel of a stereo signal.
Mono: The microphone signal is a mono signal.
Valuespace: <S: 0, 255>
Example: Experimental Audio Input Microphone 1 Channel: Mono
Example: Experimental CustomSoftbuttons State 1 Softbutton 1 Value: “”
Experimental Audio Input Microphone [1..8] EchoControl HighPassFilter
The Experimental settings can be used ‘as is’ and will not be further documented. NOTE: The
Experimental settings WILL change.
Experimental SoftwareUpgrade Mode
The Experimental settings can be used ‘as is’ and will not be further documented. NOTE: The
Experimental settings WILL change..
Valuespace: <On/Off>
Valuespace: <Auto/Manual>
Example: Experimental Audio Input Microphone 1 EchoControl HighPassFilter:
Example: Experimental SoftwareUpgrade Mode: Auto
Off
Experimental SoftwareUpgrade ServerAddress
Experimental AudioTracking Camera [1..7] Mode
The Experimental settings can be used ‘as is’ and will not be further documented. NOTE: The
Experimental settings WILL change.
The Experimental settings can be used ‘as is’ and will not be further documented. NOTE: The
Experimental settings WILL change.
Valuespace: <S: 0, 255>
Valuespace: <On/Off>
Example: Experimental SoftwareUpgrade ServerAddress: “http://csupdate.
Example: Experimental AudioTracking Camera 1 Mode: Off
tandberg.com/getswlist.py”
Experimental CapsetFilter
The Experimental settings can be used ‘as is’ and will not be further documented. NOTE: The
Experimental settings WILL change.
Experimental SystemUnit Controller Address
The Experimental settings can be used ‘as is’ and will not be further documented. NOTE: The
Experimental settings WILL change.
Valuespace: <S: 0, 32>
Valuespace: <S: 0, 255>
Example: Experimental CapsetFilter: “”
Example: Experimental SystemUnit Controller Address: “”
Experimental Conference [1..1] PacketLossResilience
The Experimental settings can be used ‘as is’ and will not be further documented. NOTE: The
Experimental settings WILL change.
Experimental UserInterfaces OSD PhonebookMerged
The Experimental settings can be used ‘as is’ and will not be further documented. NOTE: The
Experimental settings WILL change.
Valuespace: <On/Off>
Valuespace: <On/Off>
Example: Experimental Conference 1 PacketLossResilience: Off
Example: Experimental UserInterfaces OSD PhonebookMerged: Off
36
Download from Www.Somanuals.com. All Manuals Search And Download.
D14635.02—MARCH 2010
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
A
d
v
a
n
c
e
d
c
o
n
fi
g
u
r
a
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Password protection
Chapter 3
Password protection
37
D14635.02—MARCH 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
A
d
v
a
n
c
e
d
c
o
n
fi
g
u
r
a
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Password protection
Setting the codec administrator password
To define the administrator password on the codec:
Setting the menu password
To define a password for the Advanced menus:
Password protection
The system can be password protected in three ways:
1. Connect to the codec through the network or the serial data
port, using a command line interface (ssh, telnet or scp)
1. In the on-screen menu, go to Home > Settings > Advanced
•
•
•
The Advanced menu can be password protected with a menu
password.
> Set menu password.
2. Log in to the codec with user name (admin) and no password.
2. The password is a string with 0–255 characters.
3. Enter the new password in the Set password menu
4. Press Save.
The Codec can be password protected with an administrator
password.
3. Run the following API command and enter a password:
xCommand SystemUnit AdminPassword Set
Password: “****”
The Web interface is password protected with the same
administrator password as for the codec. NOTE! Requires a
reboot of the codec.
4. The password format is a string with 0–255 characters.
Log in to the Advanced menu
5. Reboot the codec.
NOTE! When a new password has been defined make sure
you save a copy of the password in a safe place. Contact your
TANDBERG representative if you have forgotten the password.
When a password is set, the password is required to get access
to the Advanced menu on screen.
Password protection of the web interface
The web interface is password protected with the same user
name and password as defined for the codec.
How to change the menu password
NOTE! To activate the administrator password on the web
interface, after having defined or changed the administrator
password, a reboot of the codec is required. Without a reboot
the administrator password will only apply when you log in to the
codec.
1. To change the password, go to Home > Settings >
Advanced > Set menu password.
2. Enter the new password in the Set password menu
3. Press Save.
Log in to the codec or the web interface
How to deactivate the menu password
•
You can log in to the codec with the user name and password,
either from a web interface or from a command line interface.
You will need to enter both the user name and password.
1. To deactivate the password, go to Home > Settings >
Advanced > Set menu password.
2. Leave the input field empty in the Set password menu.
•
The user name is admin, and cannot be changed.
3. Press Save to save the blank password. This will deactivate
the menu password.
How to deactivate the administrator password
1. Connect to the codec through the network, using a command
line interface (ssh, telnet or scp).
2. Login to the codec with the required user name (admin) and
password.
3. Run the following API command with a blank password:
xCommand SystemUnit AdminPassword Set
Password: ““
4. Reboot the codec.
38
D14635.02—MARCH 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
A
d
v
a
n
c
e
d
c
o
n
fi
g
u
r
a
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
u
d
io
m
a
t
t
e
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
About monitors
Chapter 4
About monitors
39
D14635.02—MARCH 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
A
d
v
a
n
c
e
d
c
o
n
fi
g
u
r
a
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
u
d
io
m
a
t
t
e
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
About monitors
About monitors when you have a
Codec C90
The video outputs at Codec C90
The main monitor
The main monitor can be connected to any of the video outputs
HDMI 1 (the default connector for the main monitor) HDMI 3 (the
default connector for the dual monitor), DVI-I 2 or DVI-I 4.
Connecting to HDMI 1
The HDMI 1 output is, by default, defined as the main monitor
connector. When you connect the main monitor to this output
the menu and icons (OSD - on screen display) will show on this
monitor.
DVI-I 4
HDMI 3
(the default connector
for the dual monitor)
Connecting to DVI-I 2, DVI-I 4, HDMI 3
DVI-I 2
When connecting the main monitor to the DVI–I 2, DVI–I 4 or
HDMI 3 output, you must move the OSD to this output.
HDMI 1
If you cannot see any menu on screen you must run a key
sequence on the remote control. The menu on screen, icons
and other information (OSD - on screen display) will be moved
to the selected output. At the same time, the resolution will be
set to the default value, which is 1024x768@60Hz for DVI and
1280x720@60Hz for HDMI.
(the default connector
for the main monitor)
Dual monitors
When you want to run a dual monitor setup, connect the second
monitor to video output HDMI 3 on the codec.
Moving the OSD using the remote control
If the main monitor is connected to DVI-I 2 video output you must
run the following shortcut or key sequence on the remote control.
Dual monitor configuration
Go to Advanced settings to set the monitor to dual:
•
Disconnect * # * # 0 x #
x=1 (HDMI 1); x=2 (DVI–I 2);
x=3 (HDMI 3); x=4 (DVI–I 4)
1. Navigate to Settings > Advanced > Advanced settings > Video
> Output > Monitor and set the Monitor to Dual.
Example: Set DVI-I 2 as the OSD output.
– * – # – * – # – 0 – 2 – #
Moving the OSD using API commands
You can also set the resolution and the OSD output by setting up
a serial port connection and running API commands. See the API
Guide for the codec for information about API commands.
40
D14635.02—MARCH 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
A
d
v
a
n
c
e
d
c
o
n
fi
g
u
r
a
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Audio matters
Chapter 5
Audio matters
41
D14635.02—MARCH 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
A
d
v
a
n
c
e
d
c
o
n
fi
g
u
r
a
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Audio matters
Dynamic audio API
Example 1:
When the call is established a remote input and remote output
pair are created and all the connections to these from the local
audio system are set up automatically.
With a set of xCommand Audio API commands, the audio system
is fully configurable:
The dynamic audio API offers a great flexibility when configuring
the system and it is simple to use. To have audio in your calls
you only need one local input with a microphone attached to it,
and one local output with an output connector attached to it.
•
A local input is defined as a mix of input connectors. A local
input can be created and deleted. You can add and remove
input connectors and update the local input settings.
•
A local output is a mix of local input and remote input signals.
All connectors attached to a local output receive the same
signal.
The Local input 1 has been defined
with two Microphones.
The Local output 2 has been
defined with two Line outputs.
•
•
A remote input and remote output pair is created for each call.
LOCAL INPUT 1
LOCAL OUTPUT 2
A remote output receives the signals from all local and remote
Inputs, except the remote input from the same site.
Local audio
MICROPHONE 1
setup
Line 5
•
The mixer matrix of each local and remote output can easily be
managed by disconnecting and connecting local and remote
inputs.
MICROPHONE 2
Line 6
REMOTE OUTPUT 4
REMOTE INPUT 3
Remote input
output pair
The audio from the Remote input 3
goes to the Local output 2.
The audio from the Local input 1
goes to the Remote output 4.
42
D14635.02—MARCH 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
A
d
v
a
n
c
e
d
c
o
n
fi
g
u
r
a
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Audio matters
The equalizer
The filter types
The system has 8 user defined equalizers, each made up of 6
The illustrations below shows the 5 different filter types and frequency response variations dependent on some of the parameter
variations. The Q-value for low pass, high pass, low shelf and high shelf filters should be set to 1/sqrt(2) in order to get maximally flat
responses. The Q-value (or Q-factor) is defined as Q=f0/bw. Where f0=resonance frequency in Hz; and bw=filter bandwith in Hz.
second order IIR sections, see the illustration below. Each of these
8 equalizers can be applied to one or more of the audio input and
output connectors on the codec.
dB
8
Peaking filter
Gain
Low pass and high pass filters
dB
2
Lowpass filter
Highpass filter
6
4
2
0
0
The Audio Console application
We recommend using the Audio Console, with the build in
equalizer GUI, to modify the equalizers. The Audio Console
application is found at the TANDBERG Developer Zone web page.
-2
Q
-6
-8
-10
-12
-14
-16
-18
-20
-2
-4
-6
-8
The equalizer filter parameters
Each section (1 … 6) of each user defined equalizer (1 … 8) can
be modified independently by setting the four parameters:
101
102
103
104
101
102
103
104
Frequency (Hz)
Frequency (Hz)
Low shelf filter
High shelf filter
dB
8
dB
8
•
•
•
•
Filter type (Peaking, low shelf, high shelf, low pass, high pass)
Frequency
Gain
Gain = 6 dB
Gain = 6 dB
Gain = 4 dB
Gain = 2 dB
6
4
6
4
2
0
Gain = 4 dB
Gain = 2 dB
Q-value
2
0
Gain = -2 dB
Gain = -4 dB
Gain = -6 dB
Gain = -2 dB
Gain = -4 dB
Gain = -6 dB
To switch off one of the six equalizer sections; set the second
order section to have a flat frequency response. This can be done
by setting the filter type to “none” or by setting the filter type to
“peaking” and the gain to “0” (zero).
-2
-4
-6
-2
-4
-6
-8
-8
101
102
103
104
101
102
103
104
Frequency (Hz)
Frequency (Hz)
The equalizer IIR filter
Section 1
Section 2
Section 3
Section 4
Section 5
Section 6
b0
b1
b2
b0
b1
b2
b0
b1
b2
b0
b1
b2
b0
b1
b2
b0
b1
b2
z-1
a1
z-1
a1
z-1
a1
z-1
a1
z-1
z-1
a1
a2
a1
z-1
a2
z-1
a2
z-1
a2
z-1
a2
z-1
z-1
a2
43
D14635.02—MARCH 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
A
d
v
a
n
c
e
d
c
o
n
fi
g
u
r
a
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Audio matters
Microphone reinforcement
To improve speech intelligibility in a large room, the local
Using microphone reinforcement in a large room
microphones are played out on speakers locally as well as being
sent to far end.
•
•
The room can be viewed as being divided in two zones. It
is assumed that there is a low acoustic coupling between
microphones in zone 1 and speakers in zone 2 and vice versa.
Loudspeaker
Loudspeaker
(far end)
(far end)
Microphones in zone 1 will be played out on all loudspeakers
in zone 2.
•
•
Microphones in both zones will be transmitted to far end.
Microphone 1
Microphone 2
The input signal from far end will be played out on
loudspeakers in both zones.
Zone 1
Loudspeaker
Loudspeaker
(far end + Mic 1 + Mic 2)
(far end + Mic 1 + Mic 2)
Microphone 3
Microphone 4
Zone 2
44
D14635.02—MARCH 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
A
d
v
a
n
c
e
d
c
o
n
fi
g
u
r
a
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
p
p
e
n
d
ic
e
s
C
o
n
t
a
c
t
us
Audio matters
Stereo
Local stereo circuit example (from the Audio Console)
Stereo in point to point call
Receive stereo
If the other participant sends stereo the codec will receive stereo.
To play stereo the local output still needs to be configured
correctly (see local stereo circuit example).
Transmit stereo
In order to send stereo, the other participant must be able to
receive stereo. Also, the local input with the stereo signal must be
configured correctly (see local stereo circuit example). In addition,
there must be a signal on one of the connectors connected to the
local input.
Stereo in Multisite
•
The TANDBERG Codec C90 sends and receives stereo signals
in multisite.
Presentation
Recorder
•
The TANDBERG Codec C60/C40 will only send and receive
mono signals in multisite.
The local input has two connectors: Line 1 and
Line 2. When these two connectors are mixed
together as a stereo signal, Line 1 is the left
channel and Line 2 is the right channel.
The local output has two connectors: Line 3 and
Line 4. The local output pans the stereo signal
according to the channel configuration of the
connectors. Line 3 receives the left channel and
Line 4 receives the right channel.
Examples of local stereo configuration
When you want to record a stereo presentation the audio system
can be configured as shown in the illustration.
Local stereo circuit example with API commands
In the example the local input has two connectors: Line 1 and Line
2. When these two connectors are mixed together as a stereo
signal, Line 1 is the left channel and Line 2 is the right channel.
The graphic gives a picture of how to configure the audio system for recording a stereo presentation. You can do the same from the API.
The belonging xCommands and xConfigurations are listed below.
And the local output has two connectors: Line 3 and Line 4. The
local output pans the stereo signal according to the channel
configuration of the connectors. Line 3 receives the left channel
and Line 4 receives the right channel.
In this example there is a local input with input id 5 and a local output with output id 6. Both are set to stereo by the channels parameter.
• xCommand Audio LocalInput Update Inputid:5 Name:”Presentation” MixerMode:Fixed AGC:On Mute:Off
Channels:2
• xCommand Audio LocalOutput Update Outputid:6 Name:”Recorder” Loudspeaker:No Channels:2
• xConfiguration Audio Input Line 1 Channel: Left
• xConfiguration Audio Input Line 2 Channel: Right
• xConfiguration Audio Output Line 3 Channel: Left
• xConfiguration Audio Output Line 4 Channel: Right
45
Download from Www.Somanuals.com. All Manuals Search And Download.
D14635.02—MARCH 2010
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
A
d
v
a
n
c
e
d
c
o
n
fi
g
u
r
a
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
C
o
n
t
a
c
t
us
Appendices
Chapter 6
Appendices
46
D14635.02—MARCH 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
A
d
v
a
n
c
e
d
c
o
n
fi
g
u
r
a
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
C
o
n
t
a
c
t
us
Appendices
Optimal Definition Profiles
Under ideal lighting conditions the bandwidth requirements can
be substantial reduced with the optimal definitions profiles.
Generally, we recommend the Optimal Definition set at Normal.
If lighting condition is conducive TANDBERG recommends that
you test the endpoint on the various Optimal Definition setting
prior to implementation.
To set the optimal definition profile
•
Go to: Settings > Advanced > Advanced settings > Video >
Input > Source [1..n] > OptimalDefinition > Profile
High (720p60)
Medium (w576p60)
Normal (w448p60)
•
Go to: Settings > Advanced > Advanced settings > Video >
Input > Source [1..n] > OptimalDefinition > Threshold60fps
Typically used in dedicated video
conferencing rooms. Requires good
lighting conditions for a good overall
experience.
Typically used in rooms with better than
normal, and consistent lighting.
This setting is typically used in office
environments where the environment is
normal to poorly lit.
The bandwidth requirements can be
reduced by up to 25%.
The Camera settings must be set to Motion to ensure the Optimal
Generally, we recommend the Optimal
Definition set at Normal.
Definition to work. With the Camera settings set to Sharpness, the
endpoint will transmit the highest resolution possible, regardless
of frames per second.
Under ideal conditions the bandwidth
requirements can be reduced by up to
50%.
To set the camera settings:
•
Go to: Settings > Advanced > Advanced settings > Camera.
Optimal definition profiles for systems supporting 1080p
30fps
w288p30
w448p30
w576p30
720p30
1080p30
Normal
Medium
High
256kbit/s
128kbit/s
128kbit/s
512 kbit/s
384 kbit/s
256 kbit/s
768 kbit/s
512 kbit/s
512 kbit/s
1152 kbit/s
768 kbit/s
768 kbit/s
2560 kbit/s
1920 kbit/s
1472 kbit/s
Optimal definition profiles for systems supporting 720p60
60fps
w144p60
w288p60
w448p60
w576p60
720p60
Normal
Medium
High
128kbit/s
128kbit/s
128kbit/s
512 kbit/s
384 kbit/s
256 kbit/s
1152 kbit/s
768 kbit/s
512 kbit/s
1472 kbit/s
1152 kbit/s
768 kbit/s
2240 kbit/s
1472 kbit/s
1152 kbit/s
47
D14635.02—MARCH 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
A
d
v
a
n
c
e
d
c
o
n
fi
g
u
r
a
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
C
o
n
t
a
c
t
us
Appendices
The Video Input Matrix
The video input matrix is found at the rear side of the codec and
illustrates the combinations in which the video inputs can be
connected.
Video input matrix
Input Sources
About the matrix
Connector Name
Only one video input source from each row can be active at any
time.
1
2
3
4
1st Camera
HDMI 1
HD-SDI 1 YPrPb 1
HD-SDI 2 YPrPb 2
HD-SDI 3 DVI-I 3
2nd Camera HDMI 2
The numbers in the left column represents the Video Input
Sources 1–5. The main connectors, which are used in basic
setup, are marked in orange color.
PC
HDMI 3
HDMI 4
HD-SDI 4
Comp. 5
–
Only one video input source from each
row can be active at any time.
The Comp. 5 and S-Video (YC) 5 inputs uses the same physical
connectors and can not be connected at the same time.
5
DVI-I 5
YC 5
Configure the video inputs
Go to the Advanced configuration menu on screen to configure
the video inputs.
Default configurations
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Video Input Source 1 Connector: HDMI
Video Input Source 2 Connector: HDMI
Video Input Source 3 Connector: DVI
Video Input Source 4 Connector: HDMI
Video Input Source 5 Connector: DVI
Navigate to: Settings > Advanced > Advanced Configurations >
Video > Input > Source 1. Configure the five video input sources:
•
Video Input Source [1–5] Connector: <HDMI/HDSDI/DVI/YC/
Composite/YPbPr> (the value space will differ by connector)
Video Input Source 1 Name: “Main Camera“
Video Input Source 2 Name: “Secondary Camera“
Video Input Source 3 Name: “PC“
•
•
Video Input Source [1–5] Name: <Enter a name, and save>
Video Input Source [1–5] Quality: <Motion/Sharpness>
Video Input Source 4 Name: “DVD“
Navigate to: Settings > Advanced > Advanced Configurations
> Video. Configure the main video source and the default
presentation source for the system. The values <1–5> represents
the video input sources [1–5].
Video Input Source 5 Name: “Document Camera“
Video Input Source 1 Quality: Motion
Video Input Source 2 Quality: Motion
Video Input Source 3 Quality: Sharpness
Video Input Source 4 Quality: Motion
•
•
Video MainVideoSource: <1..5>
Video Input Source 5 Quality: Sharpness
Video DefaultPresentationSource: <1..5>
Video MainVideoSource: 1 (which is the main camera)
Video DefaultPresentationSource: 3 (which is the PC)
48
D14635.02—MARCH 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
A
d
v
a
n
c
e
d
c
o
n
fi
g
u
r
a
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
C
o
n
t
a
c
t
us
Appendices
The DNAM Amplifier
TANDBERG DNAM for
Profile 65”
The TANDBERG DNAM (Digital Natural Audio
Module) used in Profile 65”, is built on two
specially designed and separate modules,
which is the amplifier and the loudspeaker
cabinet.
DNAM Loudspeaker
•
3 x 50W continuous average Center Output
Power (load specified by DNAM Center
Speakers).
•
2 x 50W continuous average Stereo Output
Power (load specified by TANDBERG
Loudspeaker Stereo Kit).
•
•
•
•
Full dynamic range for audio (high fidelity
range) or Integrated stereo speakers.
The DNAM Loudspeaker
Digital Signal Processing and Filtering on all
channels for best audio detail clarity.
•
•
•
3-way Center Speaker system
Frequency range 50Hz - 20kHz
Digital Crossover Filtering on center
channels.
DNAM Amplifier
2 x 100mm low- and midrange loudspeakers,
8 ohms nominal, reference quality (SEAS
Excel series)
15 pin D-SUB
(for loudspeakers)
In/out:
Audio In - SPDIF (stereo) or Analog (mono),
using the same connector.
•
•
•
•
1 x 25mm dome tweeter, 6 ohms nominal,
excellent quality
RCA (audio in)
RCA (loop out)
XLR–female
XLR–male
Differential In - (female XLR pinout: 1 - GND, 2 –
Signal (+), 3 – Signal (-))
Crossover filtered audio signals received
from DNAM amplifier
Loop Out - line out directly from the input,
always analog even with SPDIF in.
Power socket
Long time max power 70 Watt on all
loudspeakers
Stereo Out - (male XLR, common GND
configuration)
Enclosed MDF speaker cabinet
•
Fuse 2A 250V Slow, 5 x 20mm, Littelfuse
type 215002.
Integrated Stereo Speaker
2-way Stereo Speaker System, each side has:
•
1 x 100mm low- and midrange loudspeaker,
8 ohms nominal, reference quality (SEAS
Excel series)
•
1 x 25mm dome tweeter, 6 ohms nominal,
excellent quality
•
•
•
•
Passive crossover filter
Fuses
Frequency range 70 Hz - 20 kHz
Long time max power 70 Watt
Enclosed MDF speaker cabinet
49
Download from Www.Somanuals.com. All Manuals Search And Download.
D14635.02—MARCH 2010
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
A
d
v
a
n
c
e
d
c
o
n
fi
g
u
r
a
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
C
o
n
t
a
c
t
us
Appendices
CE Declarations
TANDBERG Codec C90
TANDBERG Profile using Codec C90
For an official, signed version of this document, or details regarding documentation from the technical
construction file, please contact TANDBERG.
For an official, signed version of this document, or details regarding documentation from the technical
construction file, please contact TANDBERG.
EC Declaration of conformity
EC Declaration of conformity
MANUFACTURER:
PRODUCT NAME:
TANDBERG Telecom AS
TANDBERG Codec C90
MANUFACTURER:
PRODUCT NAME:
TANDBERG Telecom AS
TANDBERG Telepresence T1
TANDBERG Profile 65 Dual C90
TYPE NUMBER:
DESCRIPTION:
TTC6-09
TYPE NUMBER:
DESCRIPTION:
TTC6-11
Video Conferencing Equipment
Video Conferencing Equipment
DIRECTIVES:
LVD 2006/95/EC
DIRECTIVES:
LVD 2006/95/EC
This equipment complies with.
EMC 2004/108/EC
This equipment complies with.
EMC 2004/108/EC
HARMONIZED STANDARDS:
EN 60950-1:2001, A11:2004
EN 55022 (2006)
HARMONIZED STANDARDS:
EN 60950-1:2006
Applied in order to verify compliance with
directives.
Applied in order to verify compliance with
directives.
EN 55022 (2006)
EN 55024 (1998) + A1 (2001) + A2 (2003)
EN 61000-3-2 (2006)
EN 55024 (1998) + A1 (2001) + A2 (2003)
EN 61000-3-2 (2006)
EN 61000-3-3 (1995) + A1 (2001) + A2 (2005)
EN 61000-3-3 (1995) + A1 (2001) + A2 (2005)
TEST REPORTS and
Reports/Certificates No.:
LVD (Nemko AS) 106684
EMC (Nemko AS) E08517.00
TEST REPORTS and
Reports / Certificates No.:
LVD (Nemko AS) 121982
EMC (Nemko AS) E08564.00
CERTIFICATES ISSUED BY:
CERTIFICATES ISSUED BY:
TECHNICAL CONSTRUCTION FILE NO.:
X14347
2008
TECHNICAL CONSTRUCTION FILE NO.:
X14383 rev. 2
2008
YEAR WHICH THE CE-MARK WAS
AFFIXED:
YEAR WHICH THE CE-MARK WAS
AFFIXED:
50
Download from Www.Somanuals.com. All Manuals Search And Download.
D14635.02—MARCH 2010
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
A
d
v
a
n
c
e
d
c
o
n
fi
g
u
r
a
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
C
o
n
t
a
c
t
us
Appendices
China RoHS table
This products described in this guide complies
with the Chineese RoHS.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
D14635.02—MARCH 2010
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
A
d
v
a
n
c
e
d
c
o
n
fi
g
u
r
a
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
C
o
n
t
a
c
t
us
Appendices
•
•
•
•
•
RFC 3984 RTP Payload Format for H.264 Video
RFC 4028 Session Timers in SIP
Current RFCs and drafts supported in SIP
Supported RFCs in SIP
•
RFC 1889 RTP: A Transport Protocol for Real-time
Applications
The RFC (Request for Comments) series contains technical
and organizational documents about the Internet, including the
RFC 4145 TCP-Based Media Transport in the SDP
technical specifications and policy documents produced by the
Internet Engineering Task Force (IETF).
•
•
•
•
RFC 2190 RTP Payload Format for H.263 Video Streams
RFC 2327 SDP: Session Description Protocol
RFC 4568 SDP:Security Descriptions for Media Streams
RFC 4574 The Session Description Protocol (SDP) Label
Attribute
RFC 2396 Uniform Resource Identifiers (URI): Generic Syntax
•
•
•
•
•
•
•
•
•
•
•
RFC 4582 The Binary Floor Control Protocol
RFC 4585 Extended RTP Profile for RTCP-Based Feedback
RFC 4587 RTP Payload Format for H.261 Video Streams
RFC 4629 RTP Payload Format for ITU-T Rec. H.263 Video
RFC 5168 XML Schema for Media Control
RFC 4796 The SDP Content Attribute
RFC 2429 RTP Payload Format for the 1998 Version of ITU-T
Rec. H.263 Video (H.263+)
•
•
RFC 2617 Digest Authentication
RFC 2782 DNS RR for specifying the location of services (DNS
SRV)
•
RFC 2833 RTP Payload for DTMF Digits, Telephony Tones and
Telephony Signals
RFC 4583 SDP Format for BFCP Streams
RFC 5589: SIP Call Control Transfer
•
•
RFC 2976 The SIP INFO Method
RFC 3016 RTP Payload Format for MPEG-4 Audio/Visual
Streams
draft-ietf-avt-rtp-h264-rcdo-02
•
RFC 3047 RTP Payload Format for ITU-T Recommendation
G.722.1
draft-ietf-avt-rtp-rfc3984bis-06
draft-ietf-sip-outbound-20: Managing Client Initiated
Connections
•
•
•
•
•
•
•
•
•
RFC 3261 SIP: Session Initiation Protocol
RFC 3262 Reliability of Provisional Responses in SIP
RFC 3263 Locating SIP Servers
Media capabilities supported in SIP
The audio and video media capabilities supported in SIP are the
same as for H.323.
RFC 3264 An Offer/Answer Model with SDP
RFC 3311 UPDATE method
RFC 3361 DHCP Option for SIP Servers
RFC 3420 Internet Media Type message/sipfrag
RFC 3515 Refer method
RFC 3550 RTP: A Transport Protocol for Real-Time
Applications
•
•
•
•
•
RFC 3581 Symmetric Response Routing
RFC 3605 RTCP attribute in SDP
RFC 3711 The Secure Real-time Transport Protocol (SRTP)
RFC 3840 Indicating User Agent Capabilities in SIP
RFC 3890 A Transport Independent Bandwidth Modifier for
SDP
•
•
•
RFC 3891 The SIP “Replaces” Header
RFC 3892 Referred-By Mechanism
RFC 3960 Early Media
52
D14635.02—MARCH 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
A
d
v
a
n
c
e
d
c
o
n
fi
g
u
r
a
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
C
o
n
t
a
c
t
us
Appendices
800 x 600@56, 60, 72, 75, 85 Hz (SVGA)
1920 x 1200@50 Hz (WUXGA)
1680 x 1050@60 Hz (WSXGA+)
1440 X 900@60 Hz (WXGA+)
1280 x 768@60, 75, 85 Hz (WXGA)
1400 x 1050@60, 75 Hz
1366 x 768@60 Hz
Analog YPbPr (DVI-A):
800 x 600@30 fps (SVGA)
Technical specifications
Same as YPbPr, ref. below.
1024 x 768@30 fps (XGA)
1280 x 1024@30 fps (SXGA)
1280 x 720@30 fps (720p30)
1920 x 1080@30 fps (1080p30)*
1280 x 768@30 fps (WXGA)
1440 x 900@30 fps (WXGA+)
1680 x 1050@30 fps (WSXGA+)
1600 x 1200@30 fps (UXGA)
512 x 288@60 fps (w288p60)*
768 x 448@60 fps (w448p60)*
1024 x 576@60 fps (w576p60)*
1280 x 720@60 fps (720p60)*
1920x1200@20fps (WUXGA)
Extended Display Identification Data (EDID)
TANDBERG Profile 65” Dual
2 x YPbPr inputs, supported formats:
1920 x 1080@60 Hz (1080p60)
1920 x 1080@50 Hz (1080p50)
1920 x 1080@30 Hz (1080p30)
1920 x 1080@25 Hz (1080p25)
1280 x 720@60 Hz (720p60)
1280 x 720@50 Hz (720p50)
1280 x 720@30 Hz (720p30)
720 x 576@50 Hz (576p50)
UNIT DELIVERED COMPLETE WITH:
FullHD LCD Display, Codec C90, PrecisionHD 1080p
camera, remote control, microphones, Digital Audio
Module, integrated speakers and cabling
1360 x 768@60 Hz
1280 x 960@60, 85 Hz
1280 x 800@60 Hz (WXGA)
1152 x 864@75 Hz
MONITOR
Two 65” Full HD LCD, 16:9, 1080 X 1920 resolution
848 x 480@60 Hz
BASE
720 x 576@50 Hz (576p50)
Floor standing foot plate
720 x 480@60 Hz (480p60)
4 x HD-SDI inputs, supported formats:
1920 x 1080@30 Hz (1080p30)
1920 x 1080@25 Hz (1080p25)
1280 x 720@60 Hz (720p60)
1280 x 720@50 Hz (720p50)
1280 x 720@30 Hz (720p30)
1280 x 720@25 Hz (720p25)
1 x S-Video/Composite input (BNC connector),
supported formats:
BANDWIDTH
AUDIO STANDARDS
H.323/SIP up to 6 Mbps point-to-point
Up to 10 Mbps total MultiSite bandwidth
G.711, G.722, G.722.1, 64 bit & 128 bit MPEG4 AAC-LD,
AAC-LD Stereo
PAL/NTSC
VIDEO OUTPUTS (5 OUTPUTS)
FIREWALL TRAVERSAL
AUDIO FEATURES
TANDBERG Expressway™ Technology
H.460.18, H.460.19 Firewall Traversal
2 x HDMI outputs, 2 x DVI-I outputs, supported
formats:
CD-Quality 20KHz Mono and Stereo
Eight separate acoustic echo cancellers
8-port Audio mixer
1920 x 1080@60 Hz (1080p60)
1920 x 1200@60Hz (WUXGA)
1600 x 1200@60 Hz (UXGA)
1366 x 768@60 Hz
2 x DVI-I inputs, supported formats:
VIDEO STANDARDS
Automatic Gain Control (AGC)
Automatic Noise Reduction
Active lip synchronization
H.261, H.263, H.263+, H.264
Digital (DVI-D):
Same as HDMI, ref. above.
VIDEO FEATURES
1360 x 768@60 Hz
Native 16:9 Wide screen
Advanced Screen Layouts
Intelligent Video Management
Local Auto Layout
Analog RGB (DVI-A):
AUDIO INPUTS (14 INPUTS)
1280 x 720@60 Hz (720p60)
1280 x 1024@60 Hz (SXGA)
1280 x 768@60 Hz (WXGA)
1024 x 768@60 Hz (XGA)
800 x 600@60 Hz (SVGA)
640 x 480@60 Hz (VGA)
1920 x 1080@60 Hz (1080p60)
1920 x 1200@50 Hz (WUXGA)
1680 x 1050@60 Hz (WSXGA+)
1600 x 1200@60 Hz (UXGA)
1440 x 900@60 Hz (WXGA+)
1400 x 1050@60, 75 Hz
8 x microphone, 48V phantom powered, XLR connector
each with separate echo cancellers and noise reduction,
all microphones can be set for balanced line level
9 embedded individual video compositors, one for every
output and one for every encoder
2 x RCA/Phono, Line Level: Stereo PC input
2 x RCA/Phono, Line Level: Stereo auxiliary/DVD input
2 x HDMI, digital: Stereo PC/DVD inputs
VIDEO INPUTS (13 INPUTS)
1366 x 768@60 Hz
VESA Monitor Power Management
AUDIO OUTPUTS (8 OUTPUTS)
4 x HDMI inputs, supported formats:
1920 x 1080@60, 59.94 Hz (1080p60)
1920 x 1080@50 Hz (1080p50)
1360 x 768@60 Hz
2 x XLR, balanced line level, stereo main audio
1 X Composite output (BNC connector), supported
formats:
1280 x 1024@60, 75, 85 Hz (SXGA)
1280 x 960@60, 85 Hz
2 x RCA/Phono, line level, stereo main audio, configurable
to S/PDIF
1920 x 1080@30, 29.97 Hz (1080p30)
1920 x 1080@25 Hz (1080p25)
PAL/NTSC
1280 x 800@60 Hz (WXGA)
1280 x 768@60, 75, 85 Hz (WXGA)
1280 x 720@60 Hz (720p60)
1152 x 864@75 Hz
2 x RCA/Phono, line level, stereo to recording device
1 x HDMI, digital, stereo main audio
LIVE VIDEO RESOLUTIONS (ENCODE/DECODE)
176 x 144@30 fps (QCIF)
1920 x 1080@24, 23.97 Hz (1080p24)
1280 x 720@60, 59.94 Hz (720p60)
1280 x 720@50 Hz (720p50)
1 x HDMI, digital, stereo to recording device
352 x 288@30 fps (CIF)
DUAL STREAM
512 x 288@30 fps (w288p)
576 x 448@30 fps (448p)
1024 x 768@60, 70, 75, 85 Hz (XGA)
848 x 480@60 Hz
720 x 480@60, 59.94 Hz (480p60)
640 x 480@60, 72, 75, 85 Hz (VGA)
1600 x 1200@50, 60 Hz (UXGA)
1280 x 1024@60, 75, 85 Hz (SXGA)
1024 x 768@60, 70, 75, 85 Hz (XGA)
H.239 (H.323) dual stream
BFCP (SIP) dual stream
Available in MultiSite from any site
768 x 448@30 fps (w448p)
704 x 576@30 fps (4CIF)
800 x 600@56, 60, 72, 75, 85 Hz (SVGA)
720 x 576@50 Hz
Support for resolutions up to 1080p30 in both main stream
and dual stream simultaneously
1024 x 576@30 fps (w576p)
640 x 480@30 fps (VGA)
720 x 480@60, 59.94 Hz (480p60)
640 x 480@60, 72, 75, 85 Hz (VGA)
53
Download from Www.Somanuals.com. All Manuals Search And Download.
D14635.02—MARCH 2010
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
A
d
v
a
n
c
e
d
c
o
n
fi
g
u
r
a
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
C
o
n
t
a
c
t
us
Appendices
Missed Calls with Date and Time
All specifications subject to change without notice, system
specifics may vary.
GPIO
TANDBERG Profile 65” Dual, continued...
GPIO–General purpose Input/Output
POWER
All images in these materials are for representational
purposes only, actual products may differ.
Auto-sensing power supply
100–240 VAC, 50/60 Hz
Max rating – 1400 Watts
Normal operation – 1100 Watts
Standby – 160 Watts
OTHER INTERFACES
USB host for future usage
USB device for future usage
MULTISITE FEATURES
TANDBERG and Expressway are registered trademarks or
trademarks of TANDBERG in the U.S. and other countries.
4-way High Definition SIP/H.323 MultiSite
Full Individual audio and video transcoding up to 1080p30
Individual layouts in MultiSite CP (Takes out SelfView)
H.323/SIP/VoIP in the same conference
Best Impression (Automatic CP Layouts)
H.264, Encryption, Dual Stream from any site
IP Downspeeding
All other trademarks are property of their respective
owners.
PRECISIONHD 1080P CAMERA
1/3” CMOS
MTBF PRODUCT RELIABILITY/MTBF
OPERATING TEMPERATURE AND HUMIDITY
0° C to 35° C (32° F to 95° F) ambient temperature
10% to 90% Relative Humidity (RH)
12 x zoom
The predicted reliability is expressed in the expected
random Mean Time Between Failures (MTBF) for the
electronic components for Codec C90 and PrecisionHD
1080p camera based on the Power On Hours:
+15°/-25° tilt, +/- 90° pan
43.5° vertical field of view
72° horizontal field of view
Focus distance 0.3m–infinity
Dial in/Dial out
STORAGE AND TRANSPORT TEMPERATURE
Power On Hours (POH) > 69 000 hours
Useful Life Cycle > 6 years
Conference rates up to 10 Mbps
-20° C to 60° C (-4° F to 140° F) at RH 10–90% (non-
condensing)
1920 x 1080 pixels progressive @ 60fps
PROTOCOLS
H.323
Other formats supported (configurable through Dip-
switch):
APPROVALS
ISO 9001 certificate is available upon request
March 2010
SIP
Directive 2006/95/EC (Low Voltage Directive)
— Standard EN 60950-1
1920 x 1080@60 Hz (HDMI only)
1920 x 1080@50 Hz (HDMI only)
1920 x 1080@30 Hz
EMBEDDED ENCRYPTION
Directive 2004/108/EC (EMC Directive)
— Standard EN 55022, Class A
— Standard EN 55024
H.323/SIP point-to-point and multipoint calls
Standards-based: H.235 v2 & v3 and AES
Automatic key generation and exchange
Supported in Dual Stream & MultiSite
1920 x 1080@25 Hz
1280 x 720@60 Hz
— Standard EN 61000-3-2/-3-3
Approved according to UL 60950-1 and CSA 60950-1-07
Complies with FCC15B Class A
1280 x 720@50 Hz
1280 x 720@30 Hz
IP NETWORK FEATURES
DNS lookup for service configuration
Differentiated Services (QoS)
1280 x 720@25 Hz
Automatic or manual focus/brightness/whitebalance
Far-end camera control
DIMENSIONS
Height: 65in/165cm
Width: 120in/300cm
Depth: 5.9in/15cm
IP adaptive bandwidth management (including flow
control)
Daisy-chain support (Visca protocol camera)
Dual HDMI and HD-SDI output
Auto gatekeeper discovery
Dynamic playout and lip-sync buffering
H.245 DTMF tones in H.323
Date and Time support via NTP
Packet Loss based Downspeeding
URI Dialing
Upside-down mounting with automatic flipping of picture
WEIGHT
SYSTEM MANAGEMENT
Weight: 660lbs/300kg
Support for the TANDBERG Management Suite
Total management via embedded SNMP, Telnet, SSH,
XML, SOAP
TCP/IP
Remote software upload: via web server, SCP, HTTP,
HTTPS
DHCP
1 x RS-232 local control and diagnostics
Remote control and on-screen menu system
Direct DNS dialing
802.1x network authentication
DIRECTORY SERVICES
SECURITY FEATURES
Management via HTTPS and SSH
IP Administration Password
Menu Administration Password
Disable IP services
Support for Local directories (My Contacts)
Corporate Directory
Unlimited entries using Server directory supporting LDAP
and H.350
Unlimited number for Corporate directory (through TMS)
200 number local directory
Received Calls
Network Settings protection
* requires option
NETWORK INTERFACES
** only one LAN/Ethernet interface supported
2** x separate LAN/Ethernet (RJ-45) 10/100/1000 Mbit
Placed Calls
54
Download from Www.Somanuals.com. All Manuals Search And Download.
D14635.02—MARCH 2010
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
A
d
v
a
n
c
e
d
c
o
n
fi
g
u
r
a
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
C
o
n
t
a
c
t
us
Appendices
848 x 480@60 Hz
1920 x 1080@30 Hz (1080p30)
1920 x 1080@25 Hz (1080p25)
1280 x 720@60 Hz (720p60)
1280 x 720@50 Hz (720p50)
1280 x 720@30 Hz (720p30)
720 x 576@50 Hz (576p50)
720 x 480@60 Hz (480p60)
1440 x 900@30 fps (WXGA+)
1680 x 1050@30 fps (WSXGA+)
1600 x 1200@30 fps (UXGA)
512 x 288@60 fps (w288p60)*
768 x 448@60 fps (w448p60)*
1024 x 576@60 fps (w576p60)*
1280 x 720@60 fps (720p60)*
1920x1200@20fps (WUXGA)
Technical specifications
800 x 600@56, 60, 72, 75, 85 Hz (SVGA)
720 x 576@50 Hz (576p50)
720 x 480@60, 59.94 Hz (480p60)
640 x 480@60, 72, 75, 85 Hz (VGA)
TANDBERG Codec C90
UNIT DELIVERED COMPLETE WITH:
4 x HD-SDI inputs, supported formats:
1920 x 1080@30 Hz (1080p30)
1920 x 1080@25 Hz (1080p25)
1280 x 720@60 Hz (720p60)
1280 x 720@50 Hz (720p50)
1280 x 720@30 Hz (720p30)
1280 x 720@25 Hz (720p25)
Video conferencing codec, remote control, rack mounting
rails, LAN cable, power cable
1 x S-Video/Composite input (BNC connector),
supported formats:
BANDWIDTH
AUDIO STANDARDS
PAL/NTSC
H.323/SIP up to 6 Mbps point-to-point
Up to 10 Mbps total MultiSite bandwidth
G.711, G.722, G.722.1, 64 bit & 128 bit MPEG4 AAC-LD,
AAC-LD Stereo
VIDEO OUTPUTS (5 OUTPUTS)
AUDIO FEATURES
FIREWALL TRAVERSAL
2 x HDMI outputs, 2 x DVI-I outputs, supported
formats:
CD-Quality 20KHz Mono and Stereo
Eight separate acoustic echo cancellers
8-port Audio mixer
2 x DVI-I inputs, supported formats:
TANDBERG Expressway™ Technology
H.460.18, H.460.19 Firewall Traversal
1920 x 1080@60 Hz (1080p60)
1920 x 1200@60Hz (WUXGA)
1600 x 1200@60 Hz (UXGA)
1366 x 768@60 Hz
Digital (DVI-D):
Same as HDMI, ref. above.
VIDEO STANDARDS
Automatic Gain Control (AGC)
Automatic Noise Reduction
Active lip synchronization
H.261, H.263, H.263+, H.264
Analog RGB (DVI-A):
1920 x 1080@60 Hz (1080p60)
1920 x 1200@50 Hz (WUXGA)
1680 x 1050@60 Hz (WSXGA+)
1600 x 1200@60 Hz (UXGA)
1440 x 900@60 Hz (WXGA+)
1400 x 1050@60, 75 Hz
1360 x 768@60 Hz
VIDEO FEATURES
1280 x 720@60 Hz (720p60)
1280 x 1024@60 Hz (SXGA)
1280 x 768@60 Hz (WXGA)
1024 x 768@60 Hz (XGA)
800 x 600@60 Hz (SVGA)
640 x 480@60 Hz (VGA)
Native 16:9 Widescreen
Advanced Screen Layouts
Intelligent Video Management
Local Auto Layout
AUDIO INPUTS (14 INPUTS)
8 x microphone, 48V phantom powered, XLR connector
each with separate echo cancellers and noise reduction,
all microphones can be set for balanced line level
2 x RCA/Phono, Line Level: Stereo PC input
2 x RCA/Phono, Line Level: Stereo auxiliary/DVD input
2 x HDMI, digital: Stereo PC/DVD inputs
VIDEO INPUTS (13 INPUTS)
1366 x 768@60 Hz
1360 x 768@60 Hz
4 x HDMI inputs, supported formats:
1920 x 1080@60, 59.94 Hz (1080p60)
1920 x 1080@50 Hz (1080p50)
1920 x 1080@30, 29.97 Hz (1080p30)
1920 x 1080@25 Hz (1080p25)
1920 x 1080@24, 23.97 Hz (1080p24)
1920 x 1200@50 Hz (WUXGA)
1680 x 1050@60 Hz (WSXGA+)
1600 x 1200@50, 60 Hz (UXGA)
1440 X 900@60 Hz (WXGA+)
1400 x 1050@60, 75 Hz
VESA Monitor Power Management
1280 x 1024@60, 75, 85 Hz (SXGA)
1280 x 960@60, 85 Hz
AUDIO OUTPUTS (8 OUTPUTS)
1 X Composite output (BNC connector), supported
formats:
2 x XLR, balanced line level, stereo main audio
1280 x 800@60 Hz (WXGA)
1280 x 768@60, 75, 85 Hz (WXGA)
1280 x 720@60 Hz (720p60)
1152 x 864@75 Hz
2 x RCA/Phono, line level, stereo main audio, configurable
to S/PDIF
PAL/NTSC
2 x RCA/Phono, line level, stereo to recording device
1 x HDMI, digital, stereo main audio
LIVE VIDEO RESOLUTIONS (ENCODE/DECODE)
176 x 144@30 fps (QCIF)
1024 x 768@60, 70, 75, 85 Hz (XGA)
848 x 480@60 Hz
1 x HDMI, digital, stereo to recording device
352 x 288@30 fps (CIF)
512 x 288@30 fps (w288p)
576 x 448@30 fps (448p)
DUAL STREAM
800 x 600@56, 60, 72, 75, 85 Hz (SVGA)
720 x 576@50 Hz
H.239 (H.323) dual stream
BFCP (SIP) dual stream
Available in MultiSite from any site
768 x 448@30 fps (w448p)
704 x 576@30 fps (4CIF)
720 x 480@60, 59.94 Hz (480p60)
640 x 480@60, 72, 75, 85 Hz (VGA)
1366 x 768@60 Hz
1360 x 768@60 Hz
1024 x 576@30 fps (w576p)
640 x 480@30 fps (VGA)
Support for resolutions up to 1080p30 in both main stream
and dual stream simultaneously
1280 x 1024@60, 75, 85 Hz (SXGA)
1280 x 960@60, 85 Hz
Analog YPbPr (DVI-A):
800 x 600@30 fps (SVGA)
1024 x 768@30 fps (XGA)
Same as YPbPr, ref. below.
MULTISITE FEATURES
1280 x 800@60 Hz (WXGA)
4-way High Definition SIP/H.323 MultiSite
Full Individual audio and video transcoding up to 1080p30
Individual layouts in MultiSite CP (Takes out SelfView)
H.323/SIP/VoIP in the same conference
Best Impression (Automatic CP Layouts)
Extended Display Identification Data (EDID)
1280 x 768@60, 75, 85 Hz (WXGA)
1280 x 720@60, 59.94 Hz (720p60)
1280 x 720@50 Hz (720p50)
1152 x 864@75 Hz
1280 x 1024@30 fps (SXGA)
1280 x 720@30 fps (720p30)
1920 x 1080@30 fps (1080p30)*
1280 x 768@30 fps (WXGA)
2 x YPbPr inputs, supported formats:
1920 x 1080@60 Hz (1080p60)
1920 x 1080@50 Hz (1080p50)
1024 x 768@60, 70, 75, 85 Hz (XGA)
55
Download from Www.Somanuals.com. All Manuals Search And Download.
D14635.02—MARCH 2010
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
A
d
v
a
n
c
e
d
c
o
n
fi
g
u
r
a
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
C
o
n
t
a
c
t
us
Appendices
All specifications are subject to change without notice,
system specifics may vary.
PRECISIONHD 1080P CAMERA
1/3” CMOS
POWER
TANDBERG Codec C90, continued...
Auto-sensing power supply
100–240 VAC, 50/60 Hz
All images in these materials are for representational
purposes only, actual products may differ.
12 x zoom
H.264, Encryption, Dual Stream from any site
IP Downspeeding
+15°/-25° tilt, +/- 90° pan
43.5° vertical field of view
72° horizontal field of view
Focus distance 0.3m–infinity
175 watts max. for codec and main camera
TANDBERG and Expressway are registered trademarks or
trademarks of TANDBERG in the U.S. and other countries.
OPERATING TEMPERATURE AND HUMIDITY
0° C to 35° C (32° F to 95° F) ambient temperature
10% to 90% Relative Humidity (RH)
Dial in/Dial out
All other trademarks are property of their respective
owners.
Conference rates up to 10 Mbps
1920 x 1080 pixels progressive @ 60fps
PROTOCOLS
H.323
MTBF PRODUCT RELIABILITY/MTBF
STORAGE AND TRANSPORT TEMPERATURE
Other formats supported (configurable through Dip-
switch):
The predicted reliability is expressed in the expected
random Mean Time Between Failures (MTBF) for the
electronic components based on the Power On Hours:
-20° C to 60° C (-4° F to 140° F) at RH 10–90% (non-
condensing)
SIP
1920 x 1080@60 Hz (HDMI only)
1920 x 1080@50 Hz (HDMI only)
1920 x 1080@30 Hz
EMBEDDED ENCRYPTION
Power On Hours (POH) > 69 000 hours
Useful Life Cycle > 6 years
APPROVALS
H.323/SIP point-to-point and multipoint calls
Standards-based: H.235 v2 & v3 and AES
Automatic key generation and exchange
Supported in Dual Stream & MultiSite
Directive 2006/95/EC (Low Voltage Directive)— Standard
EN 60950-1
1920 x 1080@25 Hz
1280 x 720@60 Hz
Directive 2004/108/EC (EMC Directive)— Standard EN
55022, Class B— Standard EN 55024— Standard EN
61000-3-2/-3-3
ISO 9001 certificate is available upon request
February 2010
1280 x 720@50 Hz
1280 x 720@30 Hz
IP NETWORK FEATURES
DNS lookup for service configuration
Differentiated Services (QoS)
Approved according to UL 60950-1 and CSA 60950-1-07
Complies with FCC15B Class B
1280 x 720@25 Hz
Automatic or manual focus/brightness/whitebalance
Far-end camera control
DIMENSIONS
IP adaptive bandwidth management (including flow
control)
Daisy-chain support (Visca protocol camera)
Dual HDMI and HD-SDI output
Length: 17.36in/44.1cm
Height: 3.67in/9.3cm
Depth: 11.8in/30cm
Auto gatekeeper discovery
Dynamic playout and lip-sync buffering
H.245 DTMF tones in H.323
Date and Time support via NTP
Packet Loss based Downspeeding
URI Dialing
Upside-down mounting with automatic flipping of picture
SYSTEM MANAGEMENT
WEIGHT
Support for the TANDBERG Management Suite
Weight: 11.22 lbs/5.1kg
Total management via embedded SNMP, Telnet, SSH,
XML, SOAP
TCP/IP
Remote software upload: via web server, SCP, HTTP,
HTTPS
DHCP
1 x RS-232 local control and diagnostics
Remote control and on-screen menu system
Direct DNS dialing
802.1x network authentication
DIRECTORY SERVICES
SECURITY FEATURES
Management via HTTPS and SSH
IP Administration Password
Menu Administration Password
Disable IP services
Support for Local directories (My Contacts)
Corporate Directory
Unlimited entries using Server directory supporting LDAP
and H.350
Unlimited number for Corporate directory (through TMS)
200 number local directory
Received Calls
Network Settings protection
NETWORK INTERFACES
2** x separate LAN/Ethernet (RJ-45) 10/100/1000 Mbit
Placed Calls
Missed Calls with Date and Time
GPIO
GPIO–General purpose Input/Output
* requires option
OTHER INTERFACES
USB host for future usage
USB device for future usage
** only one LAN/Ethernet interface supported
56
Download from Www.Somanuals.com. All Manuals Search And Download.
D14635.02—MARCH 2010
TANDBERG Codec C90 and Profiles using C90
Administrator guide
C
o
n
t
e
n
t
s
In
t
r
o
d
u
c
t
io
n
A
d
v
a
n
c
e
d
c
o
n
fi
g
u
r
a
t
io
n
P
a
s
s
w
o
r
d
p
r
o
t
e
c
t
io
n
A
b
o
u
t
m
o
n
it
o
r
s
A
u
d
io
m
a
t
t
e
r
s
A
p
p
e
n
d
ic
e
s
Contact us
U.S. HEADQUARTERS
TANDBERG
EUROPEAN HEADQUARTERS
TANDBERG
1212 Avenue of the Americas
24th Floor
Philip Pedersens vei 20
1366 Lysaker
New York, NY 10036
Telephone: +1 212 692 6500
Fax: +1 212 692 6501
Video: +1 212 692 6535
Norway
Telephone: +47 67 125 125
Fax: +47 67 125 234
Video: +47 67 126 126
E-mail: [email protected]
E-mail: [email protected]
57
Download from Www.Somanuals.com. All Manuals Search And Download.
D14635.02—MARCH 2010
|