Symphonic TV DVD Combo WF20D4 User Manual

OWNER’S  
MANUAL  
COLOR TV/DVD  
WF20D4 (20 inch)  
SUPPLIED ACCESSORIES  
Remote Control Unit  
Batteries  
Owner’s Manual  
Owner's Manual  
INSTRUCCIONES  
EN ESPAÑOL INCLUIDAS.  
NE228UD  
2 AA Batteries  
1EMN20057  
As an ENERGY STAR®  
Partner, our company has  
determined that this product meets  
the ENERGY STAR® guidelines for  
energy efficiency. ENERGY STAR®  
If you need additional assistance for set-up or operating after  
reading owner’s manual, please call TOLL FREE : 1-800-242-7158.  
Or visit our WEB SITE at http://www.funai-corp.com  
is a U.S. registered mark.  
Please read before using this equipment  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FIGURE A  
EXAMPLE OF ANTENNA GROUNDING AS PER  
NATIONAL ELECTRICAL CODE  
ANTENNA  
LEAD I N  
WI RE  
GROUND  
CL AMP  
ANTENNA  
DISCHARGE UNIT  
(NEC SECTION 810-20)  
ELECTRI C  
SERVICE  
EQUIPMENT  
GROUNDING CONDUCTORS  
(NEC SECTION 810-21)  
GROUND CLAMPS  
NEC  
-
NATIONAL ELECTRICAL CODE  
POWER SERVICE GROUNDING  
ELECTRODE SYSTEM  
(NEC ART 250, PART H)  
S2898A  
12.Power-Cord Protection-Power-supply cords should be  
routed so that they are not likely to be walked on or  
pinched by items placed upon or against them, paying par-  
ticular attention to cords at plugs, convenience receptacles,  
and the point where they exit from the appliance.  
19.Damage Requiring Service-Unplug this unit from the wall  
outlet and refer servicing to qualified service personnel  
under the following conditions:  
a. When the power-supply cord or plug is damaged or frayed.  
b. If liquid has been spilled, or objects have fallen into the  
unit.  
13.Outdoor Antenna grounding-If an outside antenna or  
cable system is connected to the unit, be sure the antenna or  
cable system is grounded so as to provide some protection  
against voltage surges and built-up static charges. Article  
810 of the National Electrical Code, ANSI/NFPA No. 70,  
provides information with respect to proper grounding of  
the mast and supporting structure, grounding of the lead-in  
wire to an antenna discharge unit, size of grounding con-  
ductors, location of antenna-discharge unit, connection to  
grounding electrodes, and requirements for the grounding  
electrode. (Fig. A)  
c. If the unit has been exposed to rain or water.  
d. If the unit does not operate normally by following the oper-  
ating instructions. Adjust only those controls that are cov-  
ered by the operating instructions, as improper adjustment  
of other controls may result in damage and will often  
require extensive work by a qualified technician to restore  
the unit to its normal operation.  
e. If the unit has been dropped or damaged in any way.  
f. When the unit exhibits a distinct change in performance-  
this indicates a need for service.  
14.Lightning-For added protection for this unit receiver dur-  
ing a lightning storm, or when it is left unattended and  
unused for long periods of time, unplug it from the wall  
outlet and disconnect the antenna or cable system. This will  
prevent damage to the unit due to lightning and power-line  
surges.  
20.Replacement Parts-When replacement parts are required,  
be sure the service technician has used replacement parts  
specified by the manufacturer that have the same character-  
istics as the original part. Unauthorized substitutions may  
result in fire, electric shock, injury to persons or other haz-  
ards.  
15.Power Lines-An outside antenna system should not be  
located in the vicinity of overhead power lines or other  
electric light or power circuits, or where it can fall into  
such power lines or circuits. When installing an outside  
antenna system, extreme care should be taken to keep from  
touching such power lines or circuits as contact with them  
might be fatal.  
21.Safety Check-Upon completion of any service or repairs to  
this unit, ask the service technician to perform routine safe-  
ty checks to determine that the unit is in proper operating  
condition.  
22.Heat-This unit product should be situated away from heat  
sources such as radiators, heat registers, stoves, or other  
products (including amplifiers) that produce heat.  
16.Overloading-Do not overload wall outlets and extension  
cords as this can result in a risk of fire or electric shock.  
17.Object and Liquid Entry-Never push objects of any kind  
into this unit through openings as they may touch danger-  
ous voltage points or short out parts that could result in a  
fire or electric shock. Never spill liquid of any kind on the  
unit.  
18.Servicing-Do not attempt to service this unit yourself as  
opening or removing covers may expose you to dangerous  
voltage or other hazards. Refer all servicing to qualified  
service personnel.  
EN  
3
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PRECAUTIONS  
LASER SAFETY  
IMPORTANT COPYRIGHT INFORMATION  
Unauthorized copying, broadcasting, public perfor-  
This unit employs a laser. Only a qualified service  
person should remove the cover or attempt to ser-  
vice this device, due to possible eye injury.  
mance and lending of discs are prohibited.  
This product incorporates copyright protection tech-  
nology that is protected by method claims of certain  
U.S. patents and other intellectual property rights  
owned by Macrovision Corporation and other rights  
owners. Use of this copyright protection technology  
must be authorized by Macrovision Corporation,  
and is intended for home and other limited viewing  
uses only unless otherwise authorized by  
CAUTION: USE OF CONTROLS OR ADJUST-  
MENTS OR PERFORMANCE OF PROCE-  
DURES OTHER THAN THOSE SPECIFIED  
HEREIN MAY RESULT IN HAZARDOUS  
RADIATION EXPOSURE.  
Macrovision Corporation. Reverse engineering or  
disassembly is prohibited.  
CAUTION: VISIBLE AND INVISIBLE LASER  
RADIATION WHEN OPEN AND INTERLOCK  
DEFEATED. DO NOT STARE INTO BEAM.  
LOCATION: INSIDE, NEAR THE DECK  
MECHANISM.  
FCC WARNING- This equipment may gener-  
ate or use radio frequency energy. Changes or  
modifications to this equipment may cause  
harmful interference unless the modifications  
are expressly approved in the instruction man-  
ual. The user could lose the authority to oper-  
ate this equipment if an unauthorized change  
or modification is made.  
This Class B digital apparatus complies with  
Canadian ICES-003.  
Cet appareil numérique de la classe B est con-  
forme à la norme NMB-003 du Canada.  
RADIO-TV INTERFERENCE  
This equipment has been tested and found to com-  
ply with the limits for a Class B digital device, pur-  
suant to Part 15 of the FCC Rules. These limits are  
designed to provide reasonable protection against  
harmful interference in a residential installation.  
This equipment generates, uses, and can radiate  
radio frequency energy and, if not installed and  
used in accordance with the instructions, may cause  
harmful interference to radio communications.  
However, there is no guarantee that interference  
will not occur in a particular installation. If this  
equipment does cause harmful interference to  
radio or television reception, which can be deter-  
mined by turning the equipment off and on, the  
user is encouraged to try to correct the interfer-  
ence by one or more of the following measures:  
1) Reorient or relocate the receiving antenna.  
2) Increase the separation between the equipment  
and receiver.  
CAUTION: TO PREVENT ELECTRIC SHOCK,  
MATCH WIDE BLADE OF PLUG TO WIDE  
SLOT, FULLY INSERT.  
ATTENTION: POUR ÉVITER LES CHOCS  
ÉLECTRIQUES, INTRODUIRE LA LAME LA  
PLUS LARGE DE LA FICHE DANS LA  
BORNE CORRESPONDANTE DE LA PRISE  
ET POUSSER JUSQU’AU FOND.  
A NOTE ABOUT RECYCLING  
This product’s packaging materials are recyclable  
and can be reused. Please dispose of any materials  
in accordance with your local recycling regula-  
tions.  
Batteries should never be thrown away or inciner-  
ated but disposed of in accordance with your local  
regulations concerning chemical wastes.  
3) Connect the equipment into an outlet on a cir-  
cuit different from that to which the receiver is  
connected.  
4) Consult the dealer or an experienced radio/TV  
technician for help.  
The serial number of this product may be found on the back of the unit. No other unit has the same serial  
number as yours. You should record the number and other vital information here and retain this book as a per-  
manent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.  
Date of Purchase  
Dealer Purchase from  
Dealer Address  
Dealer Phone No.  
Model No.  
Serial No.  
EN  
4
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LOCATION  
For safe operation and satisfactory performance of  
your unit, keep the following in mind when selecting  
a place for its installation:  
SYMBOLS USED IN THIS MANUAL  
The following symbols below appear in some head-  
ings and notes in this manual, with the following  
meanings  
Shield it from direct sunlight and keep it away from  
sources of intense heat.  
Avoid dusty or humid places.  
Avoid places with insufficient ventilation for proper  
heat dissipation. Do not block the ventilation holes at  
the top or bottom of the unit. Do not place the unit  
on a carpet because this will block the ventilation  
holes.  
Install unit in a horizontal position.  
Avoid locations subject to strong vibration.  
TV  
: Description refers to TV operation (in the TV mode).  
DVD-V  
: Description refers to playback of DVD video discs  
(in the DVD mode).  
CD  
: Description refers to playback of audio CDs  
(in the DVD mode).  
MP3  
: Description refers to playback of MP3 discs  
(in the DVD mode).  
Do not place the unit near strong magnetic fields.  
Avoid moving the unit to locations where tempera-  
ture differences are extreme.  
QUICK  
: Description refers to the items to be set by the  
QUICK mode (in the DVD mode).  
AVOID THE HAZARDS OF  
ELECTRICAL SHOCK AND FIRE  
Do not handle the power cord with wet hands.  
Do not pull on the power cord when disconnecting  
it from an AC wall outlet. Grasp it by the plug.  
If by accident, water is spilled on your unit, unplug  
the power cord immediately and take the unit to our  
Authorized Service Center for servicing.  
Do not put your fingers or objects into the unit disc  
loading tray.  
Do not place anything directly on top of the unit.  
WARNING  
Moisture condensation may occur inside the unit  
when it is moved from a cold place to a warm place  
or after heating a cold room or under conditions of  
high humidity. If a DVD is played in a unit which has  
moisture, it may damage the DVD and the unit.  
Therefore when the condensation occurs inside the  
unit, turn POWER on and allow at least 2 hours for  
the unit to dry out.  
EN  
5
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
C IMPORTANT SAFEGUARDS . . . . . . . . . . . . .2  
C SEARCH FUNCTION . . . . . . . . . . . . . . . . . .22  
TRACK SEARCH . . . . . . . . . . . . . . . . . . . . . .22  
TITLE / CHAPTER SEARCH . . . . . . . . . . . . .22  
TIME SEARCH . . . . . . . . . . . . . . . . . . . . . . . .22  
MARKER SETUP SCREEN . . . . . . . . . . . . . .22  
C PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . .4  
LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . .5  
AVOID THE HAZARDS OF ELECTRICAL  
SHOCK AND FIRE . . . . . . . . . . . . . . . . . . . . . .5  
WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . .5  
SYMBOLS USED IN THIS MANUAL . . . . . . .5  
C SPECIAL PLAYBACK FUNCTION . . . . . . . .23  
REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23  
PROGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . .23  
RANDOM PLAYBACK . . . . . . . . . . . . . . . . .23  
C TABLE OF CONTENTS . . . . . . . . . . . . . . . . . .6  
C FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . .7  
C PLAYING A MP3 DISC . . . . . . . . . . . . . . . . . .24  
MP3 PLAYBACK . . . . . . . . . . . . . . . . . . . . . .24  
REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24  
PROGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . .24  
RANDOM PLAYBACK . . . . . . . . . . . . . . . . .24  
C
OPERATING CONTROLS AND FUNCTIONS . . .8  
INSTALLING THE BATTERIES . . . . . . . . . . .9  
C PREPARATION FOR USE . . . . . . . . . . . . . . .10  
ANTENNA/CABLE CONNECTIONS . . . . . . .10  
CONNECTING TO EXTERNAL INPUT JACKS .11  
C CHANGING THE SETTINGS . . . . . . . . . . . .25  
SUBTITLE LANGUAGE . . . . . . . . . . . . . . . .25  
AUDIO LANGUAGE . . . . . . . . . . . . . . . . . . .25  
STEREO SOUND MODE . . . . . . . . . . . . . . . .25  
CAMERA ANGLE . . . . . . . . . . . . . . . . . . . . . .25  
BLACK LEVEL SETTING . . . . . . . . . . . . . . .25  
VIRTUAL SURROUND . . . . . . . . . . . . . . . . .25  
CONNECTING TO AN AMPLIFIER  
EQUIPPED WITH DIGITAL INPUT JACKS,  
MD DECK OR DAT DECK (for DVD only) . .11  
CONNECTING TO A DOLBY DIGITAL  
DECODER (for DVD) . . . . . . . . . . . . . . . . . . .12  
TV SECTION  
C SET UP FOR USE . . . . . . . . . . . . . . . . . . . . .13  
SELECTING THE LANGUAGE . . . . . . . . . . .13  
CHANNEL SET UP . . . . . . . . . . . . . . . . . . . . .13  
DELETING (OR ADDING) CHANNEL(S) . . .14  
C THE ON-SCREEN INFORMATION . . . . . . .26  
C CHANGING THE DVD SETUP ITEMS . . . .27  
LANGUAGE SETTING . . . . . . . . . . . . . . . . .27  
DISPLAY SETTING . . . . . . . . . . . . . . . . . . . .28  
AUDIO SETTINGS . . . . . . . . . . . . . . . . . . . . .28  
PARENTAL CONTROL . . . . . . . . . . . . . . . . .29  
INITIALIZE . . . . . . . . . . . . . . . . . . . . . . . . . . .29  
C TV OPERATION . . . . . . . . . . . . . . . . . . . . . . .15  
WATCHING A TV PROGRAM . . . . . . . . . . . .15  
DEGAUSSING . . . . . . . . . . . . . . . . . . . . . . . .15  
PICTURE CONTROL . . . . . . . . . . . . . . . . . . .15  
SLEEP TIMER . . . . . . . . . . . . . . . . . . . . . . . . .16  
CLOSED CAPTION SYSTEM . . . . . . . . . . . .16  
V-CHIP SET UP . . . . . . . . . . . . . . . . . . . . . . . .17  
C TROUBLESHOOTING GUIDE . . . . . . . . . . .30  
C MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . .32  
DVD SECTION  
C ABOUT THE DISCS . . . . . . . . . . . . . . . . . . . .19  
DISC HANDLING . . . . . . . . . . . . . . . . . . . . . .32  
C SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . .33  
C ESPAÑOL . . . . . . . . . . . . . . . . . . . . . . . . . . . .34  
C WARRANTY . . . . . . . . . . . . . . . . . . .Back Cover  
PLAYABLE DISCS . . . . . . . . . . . . . . . . . . . . .19  
DISC TYPES . . . . . . . . . . . . . . . . . . . . . . . . . .19  
C PLAYING A DISC . . . . . . . . . . . . . . . . . . . . . .20  
BASIC PLAYBACK . . . . . . . . . . . . . . . . . . . .20  
GENERAL FEATURES . . . . . . . . . . . . . . . . . .20  
DISC MENU . . . . . . . . . . . . . . . . . . . . . . . . . .20  
TITLE MENU . . . . . . . . . . . . . . . . . . . . . . . . .20  
RESUME . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21  
PAUSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21  
STEP BY STEP PLAYBACK . . . . . . . . . . . . .21  
FAST FORWARD/REVERSE SEARCH . . . . .21  
SLOW FORWARD / SLOW REVERSE . . . . .21  
EN  
6
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FEATURES  
TV Mode  
DVD Mode  
¡Dolby Digital sound  
181 channel capability PLL frequency synthesiz-  
er tuner with direct station call  
(A converter may be necessary to view scrambled cable  
channels.)  
This unit can handle Dolby Digital surround sound  
having 5.1 channels when connected to a Dolby Digital  
decoder.  
¡Still/fast/slow/step playback  
Various playback modes are available including still pic-  
tures, fast forward/reverse, slow motion and step frames.  
Infrared remote control  
Trilingual on screen menu display selectable in  
English, Spanish or French  
¡Random playback for audio CD and MP3  
This unit can shuffle the order of tracks to play them in  
random order.  
¡Sleep Timer  
The Sleep Timer function enables you to shut off the power  
without pressing POWER after a desired time period.  
¡Program playback for audio CD and MP3  
You can program the order of tracks to play them in any  
desired order.  
¡Closed Caption Decoder  
You may view specially labeled (cc) TV programs,  
movies, news, etc. with either a dialogue caption or text  
display added to the program.  
¡DVD menus in a desired language  
You can display DVD menus in a desired language, if  
available on a DVD.  
¡Auto Shut Off Function  
If there is no air signal input from the antenna terminal and  
no operation for 15 minutes, the unit will turn itself off  
automatically.  
¡Screen saver/Auto power-off functions  
The screen saver program starts when there is no input  
from the unit for 5 minutes in the stop mode. When the  
screen saver program is activated for 15 minutes, the  
power is automatically turned off.  
¡V-CHIP  
Enables parents to prevent their children from watching  
inappropriate material on TV.  
¡Subtitles in a desired language  
You can select a desired language for the display subtitles,  
if that language is available on a disc.  
¡Selecting a camera angle  
You can select the desired camera angle, if a disc contains  
sequences recorded from different angles.  
¡Choices for audio language and sound mode  
You can select the desired audio language and sound mode,  
if different languages and modes are available on a disc.  
¡Parental lock  
You can set the control level to limit playback of discs  
which may not be suitable for children.  
¡Automatic detection of discs  
This unit automatically detects if the loaded disc is DVD,  
audio CD or MP3 on disc.  
¡On-screen display  
Information about the current operation can be displayed  
on a TV screen, allowing you to confirm the currently  
active functions (such as program playback), on the TV  
screen using the remote control.  
¡Search  
Chapter search / Title search / Track search / Time search  
¡Repeat  
Chapter / Title / Track / Group / All / A-B  
¡Marker  
The part designated by user can be called back.  
¡Resume Play  
User can resume to playback from the part at which the  
play was stopped.  
¡Virtual Surround  
¡Bit rate indication  
¡DRC (Dynamic range control)  
You can control the range of sound volume.  
EN  
7
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATING CONTROLS AND FUNCTIONS  
[Fig. 1]  
TV/DVD FRONT PANEL  
OPEN/  
POWER  
VOLUME  
CHANNEL  
STOP  
SKIP  
PLAY  
SKIP  
PAUSE CLOSE  
VIDEO  
L–AUDIO–R  
–SEARCH–  
HEADPHONE  
1
2
3
4
5
6
7 8 9 10111213 14  
7. Remote Sensor Window  
[Fig. 2]  
REMOTE CONTROL  
8. STOP Button [page 20]  
Stops operation of the disc.  
9.SKIP H Button [page 21]  
Plays back from the beginning of the current  
chapter or track.  
SEARCH (REV) E Button (Front Panel)  
[page 21]  
During playback or in the pause mode, press and  
hold button down for a few seconds to change  
reverse playback speed.  
OPEN/  
CLOSE  
POWER PICTURE SELECT  
4
13  
34  
36  
1
4
2
5
8
0
3
6
CH.  
6
16  
7
SLEEP  
9
+100  
10. PLAY Button [page 20]  
VOL.  
5
Starts playback of the disc contents.  
Press to change to DVD mode when TV mode.  
+10  
17  
SKIP  
V.SURR  
MUTE  
9
11  
10  
35  
19  
18  
11. SKIP G Button [page 21]  
Plays back from the beginning of the next chapter  
or track.  
PLAY  
STOP  
REV  
FWD  
SEARCH (FWD) D Button (Front Panel)  
[page 21]  
8
DISC  
PAUSE SLOW  
DISPLAY  
MENU  
12  
23  
33  
During playback or in the pause mode, press and  
hold button down for a few seconds to change for-  
ward playback speed.  
32  
31  
30  
ENTER  
SETUP  
TITLE  
RETURN  
20  
21  
22  
12. PAUSE Button [page 21]  
CLEAR SEARCH MODE REPEAT  
A-B  
Pauses the current disc operation.  
29  
13. OPEN/CLOSE Button [page 20]  
Press to insert discs into or remove them from the  
tray.  
14. HEADPHONE Jack  
To connect headphone (not supplied) for personal  
listening.  
15. MODE Button [pages 23-25]  
Activates program playback or random playback  
mode when playing CDs or MP3.  
AUDIO SUBTITLE ANGLE  
MODE  
15  
24  
25  
28  
27  
26  
1. Disc loading tray  
2. VIDEO input Jack [page 11]  
Connect to the video output jack of a video  
camera or VCR.  
16. Number Buttons  
3. AUDIO L/R input Jacks [page 11]  
Connect to the audio output jacks of a video  
camera or VCR.  
TV Mode: [page 15]  
Press two digits to directly access the desired channel.  
Remember to press 0 before a single digit channel.  
+100 Button  
4. POWER Button [page 13]  
Press to turn the power on and off.  
Press to select cable channels which are higher than 99.  
DVD Mode: [page 22]  
5. VOLUME K/L (VOL.  
m/n) Buttons  
Press to control the volume level for the DVD and TV.  
Press to enter the desired number.  
+10 Button  
6. CHANNEL K/L (CH. K/L) Buttons [page 14]  
Press to select memorized channel.  
Press to change to TV mode when DVD mode.  
Press to enter the desired numbers which are greater  
than 9.  
EN  
8
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
[Fig. 3]  
TV/DVD REAR VIEW  
ANT.  
COAXIAL  
37  
38 39  
Press to accept a setting.  
17. SLEEP Button [page 16]  
Press SLEEP to display the sleep timer and start the  
function. The shut off time can be determined by the  
number of times you press this button. (0, 30, 60, 90  
or 120 minutes)  
32. Arrow Buttons  
TV Mode: [page 13]  
Press to select a setting mode from the menu on the  
TV screen.  
Press to select or adjust from a particular menu.  
18. REV h Button [page 21]  
Press to view the DVD picture in fast reverse  
motion. Press PAUSE, then press this button to begin  
slow motion playback. Press this button repeatedly  
to change the reverse speed of slow motion.  
DVD Mode: [page 20]  
Use when making settings while watching the  
display on a TV screen.  
33. DISC MENU Button [page 20]  
FWD g Button [page 21]  
Displays the menus in the DVD.  
Press to fast forward the Disc. Press PAUSE, then  
press this button to begin slow motion playback.  
Press this button repeatedly to change the forward  
speed of slow motion.  
34. SELECT Button [page 20]  
Press to change to TV mode, external input mode or  
DVD mode.  
NOTE: When you select the DVD mode by this  
button, press PLAY or OPEN/CLOSE first.  
Otherwise, the DVD features are not operated.  
19. V.SURR (VIRTUAL SURROUND) Button  
[page 25]  
Press to set virtual surround on/off.  
20. SETUP Button [pages 13,27-29]  
Press to enter or exit the TV menu or DVD setup  
mode.  
35. MUTE Button  
Press MUTE to turn off the sound portion of the TV  
program. (Volume level display turns LIGHT RED  
from LIGHT BLUE.) Press MUTE again or press  
21. TITLE Button [page 20]  
Displays the title menu.  
VOL.  
m
or  
nto restore sound.  
22. CLEAR Button [pages 22-24]  
36. PICTURE Button [page 15]  
Resets a setting.  
Press to enter picture adjustment mode.  
23. DISPLAY Button  
37. Power cord  
TV Mode:  
Connect to a standard AC outlet (120V/60Hz).  
NOTE: Remove the power cord from the hook to  
avoid breaking a wire before you connect to  
a standard AC outlet.  
Press to display the channel number on the screen.  
If you press it again, the channel number will disap-  
pear.  
DVD Mode: [page 26]  
38. COAXIAL digital audio out Jack (DVD Audio  
Displays the current status on the TV screen for  
checking purposes.  
Only) [pages 11, 12]  
Connect to the digital input of an external  
amplifier or decoder.  
24. SEARCH MODE Button [page 22]  
Press to locate a desired point.  
39. ANT. in Jack  
25. AUDIO Button [page 25]  
Press to select a desired audio language or sound  
mode.  
Connect to an antenna, cable system or satellite sys-  
tem.  
26. SUBTITLE Button [page 25]  
Press to select a desired subtitle language.  
INSTALLING THE BATTERIES  
27. REPEAT Button [page 23]  
Repeats playback of the current disc, title, chapter,  
group or track.  
28. ANGLE Button [page 25]  
Press to change the camera angle to see the sequence  
being played back from a different angle (if avail-  
able).  
1)Open the battery compartment cover by pressing the  
cover on the remote unit in the direction of the arrow.  
2)Insert 2 “AA” penlight batteries into the battery  
compartment in the direction indicated by the  
polarity (+/-) markings.  
29. REPEAT A-B Button [page 23]  
3)Replace the cover.  
Repeats playback of a selected section.  
30. RETURN Button [page 25]  
Returns to the previous operation in the DVD setup  
mode.  
31. ENTER Button [pages 13, 20]  
NOTES:  
¡Do not mix alkaline and manganese batteries.  
¡Do not mix old and new batteries.  
EN  
9
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREPARATION FOR USE  
ANTENNA/CABLE CONNECTIONS  
From Cable System or  
Satellite Box or  
Cable Box  
(Not supplied)  
VHF/UHF Antenna  
(Not supplied)  
OUT  
IN  
Satellite Dish  
VHF Antenna  
(Not supplied)  
UHF Antenna  
(Not supplied)  
From  
Cable System  
ANT.  
COAXIAL  
VHF/UHF  
Combiner  
(Not supplied)  
or  
or  
ANT.  
or  
75-ohm Coaxial  
Cable (Not supplied)  
Flat twin-lead cable  
[Fig. 4]  
Note to CATV system installer:  
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that  
provides guidelines for proper grounding and in particular, specifies that the cable ground shall be connect-  
ed to the grounding system of the building as close to the point of cable entry as practical.  
Bent pin  
NOTE:  
Before plugging the antenna into the ANT. IN jack of the unit, check that  
the pin is not bent. If it is bent, straighten the pin as illustrated, then plug  
the pin into the ANT. IN jack of the unit.  
Cable  
Plug  
(Needs to be straightened)(Straight pin)  
VHF/UHF COMBINED ANTENNA  
A VHF UHF 75 ohm combination antenna can be  
connected to ANT terminal.  
CABLE WITH CONVERTER/DESCRAM-  
BLER BOX OR SATELLITE BOX  
If your cable service supplies you with a converter  
box or if you use a satellite system, you can use the  
basic connection shown here.  
Channel selection must be made with the converter  
box or satellite box. This means that channels cannot  
be changed using the TV/ DVD Remote Control.  
VHF/UHF SEPARATE ANTENNAS  
In some areas it will be necessary to use an outdoor  
antenna.  
CABLE WITHOUT CONVERTER/  
DESCRAMBLER BOX  
Use this connection if your cable system connects  
directly to your unit without a converter box. Use the  
TV/ DVD Remote Control to select channels.  
TO VIEW A SCRAMBLED/UNSCRAMBLED  
CHANNEL  
1.Set the TV/DVD channel selector to the output  
channel of the Cable Converter Box or Satellite  
Box. (Ex. CH3)  
2.Select the channel to view on your Cable Converter  
Box or Satellite Box.  
EN  
10  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTING TO EXTERNAL INPUT JACKS  
When you watch a program recorded on another  
source (VCR or video camera), use the audio/video  
input jacks on the front of the unit.  
[Front of the TV/DVD]  
VIDEO L–AUDIO–R  
To the  
[Another source]  
audio out-  
put jacks  
Connect the audio/video output  
jacks of another source to the  
AUDIO L/R and VIDEO jacks of  
this unit. Then press SELECT until  
"AUX" appears on the screen.  
NOTE:  
AUX  
VIDEO  
L–AUDIO–R  
Audio/Video  
cables  
(not supplied)  
When you connect a monaural VCR (another  
source) to this unit, connect the Audio output jack  
of the monaural VCR (another source) to the  
AUDIO L jack of this unit. The audio will output in  
both L and R channel equally.  
etc.  
To the video  
output jack  
[Fig. 5]  
CONNECTING TO AN AMPLIFIER EQUIPPED WITH DIGITAL  
INPUT JACKS, MD DECK OR DAT DECK (for DVD only)  
Use an audio coaxial digital cable available at retail for the audio connections.  
Amplifier equipped with digital  
input jacks, MD deck,  
DAT deck, etc.  
ANT.  
COAXIAL  
To COAXIAL DIGITAL  
AUDIO INPUT jack  
To DIGITAL AUDIO OUT  
(PCM/BITSTREAM)  
COAXIAL jack  
(only DVD AUDIO OUT)  
[Fig. 6]  
NOTES:  
The audio source on a disc in a 5.1 channel Dolby Digital surround format cannot be recorded as digital  
sound by an MD or DAT deck.  
Be sure to turn off the power to all components in the system before connecting another component.  
Refer to the Owner's Manuals for the components to be connected to the unit.  
Set DOLBY DIGITAL to OFF for audio output in the setup mode. Playing a TV/DVD using incorrect set-  
tings may generate noise distortion and may also damage the speakers. (Refer to page 28 to set DOLBY  
DIGITAL to OFF.)  
EN  
11  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTING TO A DOLBY DIGITAL DECODER (for DVD)  
If using this unit to play a DVD disc in a 5.1 channel Dolby Digital surround format, it outputs a DOLBY  
DIGITAL Data stream from its COAXIAL digital audio out jack. By hooking the unit up to a Dolby Digital  
decoder, you can enjoy a more convincing, realistic ambience with powerful and high-quality surround sound  
as enjoyed in movie theaters.  
Use audio coaxial digital cables available at retail for the audio connections.  
Center  
speaker  
ANT.  
COAXIAL  
Front speaker  
(left)  
Front speaker  
(right)  
To DIGITAL AUDIO OUT  
(PCM/BITSTREAM)  
COAXIAL jack  
Dolby Digital decoder  
To COAXIAL DIGITAL  
AUDIO INPUT jack  
Subwoofer  
Surround  
speaker  
(left)  
Surround  
speaker  
(right)  
[Fig. 7]  
NOTES:  
Be sure to turn off the power to all components in the system before connecting another component.  
Refer to the Owner's Manuals for the components to be connected to the unit.  
If connected to a Dolby Digital decoder, set DOLBY DIGITAL to ON for audio output in the setup mode.  
(Refer to page 28 to set DOLBY DIGITAL to ON.)  
Unless connected to a Dolby Digital decoder, set DOLBY DIGITAL to OFF for audio output in the setup  
mode. Playing a TV/DVD using incorrect settings may generate noise distortion and may also damage the  
speakers.  
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are  
trademarks of Dolby Laboratories.  
EN  
12  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TV SECTION  
SET UP FOR USE  
SELECTING THE LANGUAGE  
CHANNEL SET UP  
TV  
TV  
You can program the tuner to scan all the channels  
you receive in your area.  
1 Plug in the TV/DVD power cord  
Plug the unit power cord into a standard  
AC outlet.  
NOTE: Channel memory programming is NOT  
needed when connected to a cable box or satellite  
box. Just select the unit channel selector to the output  
channel of the cable box or satellite box (Ex CH3),  
then select the channel to be viewed on the Cable  
Box or Satellite Box.  
NOTE:  
If any digits appear in the corner of  
the screen, press POWER without  
unplugging the power cord.  
Make sure ...  
Make sure ...  
Press POWER to turn on the unit.  
NOTE: This function effects only the language on  
Press POWER to turn on the unit.  
the screen menu and not the audio source.  
1 Select “CHANNEL SET UP”  
Press SETUP on the remote control.  
Press Arrow (K/L) to point to  
“CHANNEL SET UP”.  
- TV SETUP -  
- TV SETUP -  
2 Select “LANGUAGE”  
B
CHANNEL SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
CHANNEL SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
Press SETUP on the remote control.  
B
Press Arrow (K/L) to point to  
Then press ENTER.  
“LANGUAGE”.  
2 Begin auto ch programming  
Press Arrow (K/L) to point to  
“AUTO CH PROGRAMMING”.  
Then press ENTER.  
3 Select “ENGLISH”, “ESPAÑOLor “FRANÇAIS”  
Select “ENGLISH”, “ESPAÑOL”= Spanish or  
“FRANÇAIS”= French using ENTER.  
– CHANNEL SET UP –  
ADD / DELETE CH (CATV)  
AUTO CH PROGRAMMING  
B
The tuner scans and memorizes all  
the active channels in your area.  
4 Exit the Language mode  
Press SETUP to return to TV mode.  
NOTE: If for some reason the menu is in Spanish or  
French, press SETUP, press Arrow (K/L) to point to  
“IDIOMA [ESPAÑOL]” or “LANGAGE  
[FRANÇAIS]”, then press ENTER, then press  
SETUP on the remote control.  
3 After scanning  
The tuner stops on the lowest memorized channel.  
When AUTO CH PROGRAMMING is activated  
where there is no TV signal input, “NO TV SIG-  
NALS” will appear on the display after the com-  
pletion of the channel scanning.  
The unit may recognize TV channels to be CATV  
channels by the receiving conditions. In this case,  
try auto ch programming again after checking  
antenna connection.  
EN  
13  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DELETING (OR ADDING)  
CHANNEL(S)  
TV  
The channels you no longer receive or seldom watch  
can be deleted from the memory. (Of course, you can  
add the deleted channel into the memory again.)  
1 Select “CHANNEL SET UP”  
Press SETUP on the remote control.  
- TV SETUP -  
Press Arrow (K/L) to point to  
“CHANNEL SET UP”.  
B
CHANNEL SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
Then press ENTER.  
– CHANNEL SET UP –  
2 Select “ADD/DELETE CH”  
Press Arrow (K/L) to point to  
“ADD/DELETE CH”.  
B
ADD / DELETE CH (CATV)  
AUTO CH PROGRAMMING  
Press ENTER.  
3 Enter the desired channel number  
Press Arrow (K/L) until your  
desired channel number appears.  
(You can also use the number but-  
tons or CHANNEL(CH.) K/L to  
enter it) (Example: CH8)  
08  
ADD / DELETE  
You must precede single-digit  
channel numbers with a zero (Example: 02 ... 09).  
When selecting cable channels which are higher  
than 99, press +100 first, then press the last two  
digits. (Example: to select channel 125, first press  
+100, then press 2 and 5).  
4 Delete (or add) it from (or into) memory  
Press ENTER. The channel number changes to light  
red. The channel is deleted from memory.  
To delete another channel, repeat steps [3] and [4].  
If you press ENTER again, the channel is memo-  
rized again.  
Added channel: Light blue.  
Deleted channel: Light red.  
5 Exit the channel setup mode  
Press SETUP to return to TV mode.  
NOTE: To confirm that channel(s) has been deleted  
or added, press CHANNEL(CH.) K/L.  
EN  
14  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TV OPERATION  
WATCHING A TV PROGRAM  
PICTURE CONTROL  
TV  
TV  
1 Turn on the TV/DVD  
The unit’s picture controls – BRIGHT, CON-  
TRAST, COLOR, TINT and SHARPNESS – are  
preset to factory specifications. Although they are  
usually the best, you may need to make some further  
adjustments for a more natural looking image.  
Press POWER to turn on the unit.  
2 Select the channel number  
Press CHANNEL(CH.) K/L to select your desired  
channel number or press the number buttons.  
Notes for using the number buttons on the remote  
control:  
Make sure ...  
The unit is turned on.  
You must precede single-digit channel numbers  
with a zero (Example: 02 ... 09).  
When selecting cable channels which are higher  
than 99, press +100 first, then press the last two  
digits. (Example: to select channel 125, first press  
+100, then press 2 and 5).  
1 Select “PICTURE CONTROL”  
Press PICTURE on the remote control.  
2 Select item you want to adjust  
Press Arrow (K/L) until desired control is displayed.  
Remember:  
¡If the unit is connected to a cable box or satellite  
box, it must be on CH3 or CH4, then the channel  
to be viewed must be selected on the cable box or  
satellite box.  
BRIGHT  
CONTRAST  
COLOR  
BRIGHT  
TINT  
P
P
P
P
P
P
P
C
P
P
P
P
P
P
P +  
SHARPNESS  
3 Adjust sound  
Press VOLUME(VOL.) X/Y to  
3 Adjust the picture control  
Press Arrow (s / B) to adjust to your desired level  
adjust the volume.  
VOLUME 20  
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
within 5 seconds.  
NOTE:  
NOTE:  
If you press CHANNEL(CH.) K/L in the DVD  
mode, you can change the TV channels.  
At step [3], the picture adjustment display will dis-  
appear from the TV screen after about 5 seconds  
unless you press any buttons, even though you may  
not be finished. In this case, repeat from step [1].  
Even if you turn off the unit in the DVD mode,  
when you turn it on again, it will go into the TV  
mode.  
s
B
BRIGHT  
to decrease  
brightness  
to decrease  
contrast  
to increase  
brightness  
to increase  
contrast  
DEGAUSSING  
Magnetism from nearby appliances and speakers  
might affect the color of the TV picture.  
If this happens, move this unit away from the appli-  
ance. If the color is still not correct, disconnect power  
cord from AC outlet then reconnect it after 30 minutes.  
CONTRAST  
COLOR  
TINT  
SHARPNESS to soft  
to pale  
to brilliant  
to purple  
to green  
to clear  
If there is a power failure of any kind, the unit will  
retain its memory for this feature.  
EN  
15  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTE:  
SLEEP TIMER  
If the unit displays a black box on  
the TV screen, this means that the  
unit is set to the TEXT mode. To  
clear screen, select [CAPTION1],  
[CAPTION2] or [OFF].  
TV  
T
he Sleep Timer function enables you to shut off the power  
without pressing POWER after a desired time period.  
Make sure ...  
1 Set “SLEEP TIMER”  
The unit is turned on.  
Press SLEEP on the remote control.  
You may change the sleep time  
with pressing SLEEP repeatedly.  
1 Select “CAPTION”  
Press SETUP on the remote control.  
Press K or L to point to “CAP-  
TION”.  
- TV SETUP -  
The timer is set up to 120 minutes,  
30 minutes each time SLEEP is  
pressed.  
SLEEP 120 MINUTE  
CHANNEL SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
B
To cancel the sleep timer:  
Press SLEEP repeatedly until “SLEEP 0 MINUTE”  
is displayed.  
2 Select your desired caption menu  
Press ENTER until your desired  
caption menu appears.  
- TV SETUP -  
NOTES:  
CHANNEL SET UP  
V-CHIP SET UP  
When you disconnect the unit from the AC outlet,  
or if you have a power failure, the sleep time will  
be lost.  
LANGUAGE [ENGLISH]  
CAPTION [CAPTION1]  
([CAPTION1], [CAPTION2],  
[TEXT1] or [TEXT2])  
B
To view the time left for sleep timer press SLEEP  
once when SLEEP display disappears. After 10  
seconds, display will disappear again.  
3 Exit the caption setting mode  
Press SETUP to return to TV mode.  
CLOSED CAPTION SYSTEM  
TV  
TO CANCEL THE CLOSED CAPTION  
SYSTEM  
You can view specially labeled (cc) TV programs,  
movies, news, etc. with either a dialogue caption or  
text display.  
CAPTION mode: By choosing the caption mode, you  
can watch dramas, movies and news while captioning  
the dialogues and the contents of news.  
Repeat steps [1] to [2], select [OFF] using ENTER.  
Press SETUP on the remote control to return to TV  
mode.  
TEXT mode: By choosing the text mode, you can  
watch half screen text information if you want.  
1-2: You may get these captions or text information  
by selecting either “1” or “2”. Caption “2” is used,  
usually for a second language if available.  
WHEN THE CLOSED CAPTION MODE  
IS ON  
The On-Screen Display will disappear after 5 sec-  
onds.  
This is also true when MUTE is pressed.  
If there is a power failure of any kind, the unit will  
retain its memory for this feature.  
NOTE:  
Not all programs are broadcast with closed captions.  
Your television is designed to provide error free  
closed captions from high quality antenna, cable and  
VCR signals. Conversely, poor quality signals are  
likely to result in caption errors or no captions at all.  
Common signal conditions which may cause captions  
errors are listed below:  
Automobile ignition noise  
Electric motor brush noise  
Weak snowy reception on TV screen  
Multiplex signal reception displaying picture  
ghosts or airplane flutter.  
EN  
16  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
V-CHIP SET UP  
When you select a rating category and set it to  
[BLOCK], the higher rating will change to  
[BLOCK] automatically. Also, the lower rating will  
change to [VIEW] automatically.  
When you set “TV-Y” to [VIEW], all ratings will  
change to [VIEW] automatically.  
TV  
V-CHIP enables parents to prevent their children  
from watching inappropriate material on TV.  
V-CHIP reads the ratings for programming (except  
for news and sports programs, unedited movies on  
premium cable channels and Emergency Broadcast  
System signals), then denies access to programming  
if the program’s rating meets the limitations you  
select. In this case, “PROTECTED PROGRAM by  
...” message appears on the TV screen.  
Selection  
TV-Y  
Rating Category Explanations  
Appropriate for all children  
TV-Y7  
TV-G  
Appropriate for children seven and older  
General Audience  
TV-PG  
TV-14  
Parental Guidance suggested.  
Unsuitable for children under 14  
To block ratings, follow the steps below.  
TV-MA Mature audience only  
Programming may be rated by the Motion Picture  
Association of America (MPAA) or according to  
the Television Parental Guidelines. In order to  
block any inappropriate programming, set your  
limits in both places (MPAA RATING and TV  
RATING).  
When you select TV-Y7, TV-PG, TV-14 or TV-MA  
and you press ENTER, the sub-ratings will appear  
on the TV screen.  
If you select the rating category (example: TV-PG)  
and turn it [BLOCK] or [VIEW], the sub-ratings  
(example: V for Violence) will turn [BLOCK] or  
[VIEW] automatically.  
TV RATING SET UP  
You can set the sub-ratings to [BLOCK] or [VIEW]  
individually when the rating category is set to  
[BLOCK].  
Make sure ...  
The unit is turned on.  
To set the sub-ratings individually, follow the steps  
below.  
- TV SETUP -  
1 Select “V-CHIP SET UP”  
CHANNEL SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
Press SETUP on the remote control.  
B
When you select [TV-Y7]:  
Press Arrow (K/L) to point to  
V-CHIP SET UP”.  
Then press ENTER.  
TV–Y7  
FV  
[BLOCK]  
[BLOCK]  
Press Arrow (K/L) to select  
“FV” (Fantasy Violence).  
Then press ENTER to select  
[BLOCK] or [VIEW].  
B
2 Input Access code  
Press the number buttons to enter 4-  
digit access code. The default code  
is 0000.  
ACCESS CODE  
When you select [TV-PG], [TV-14] or [TV-MA]:  
Press Arrow (K/L) to select  
_
_
_
_
“D”(Suggestive Dialog),  
TV–PG  
[BLOCK]  
B
D
L
S
V
[BLOCK]  
[BLOCK]  
[BLOCK]  
[BLOCK]  
“L”(Coarse Language),  
“S”(Sexual Situation) or  
“V”(Violence). Then press  
ENTER to select [BLOCK] or [VIEW].  
NOTE: When you select [TV-MA], “D” does not  
appear on the TV screen.  
3 Select “TV RATING”  
Press Arrow (K/L) to point to  
“TV RATING”.  
– V-CHIP SET UP –  
B
TV RATING  
MPAA RATING  
CHANGE CODE  
The sub-ratings which are set to  
B
TV–Y  
TV–Y7  
TV–G  
TV–PG (DLSV)  
TV–14 (DLSV)  
TV–MA ( LSV)  
[VIEW]  
(
)
[VIEW]  
Then press ENTER.  
[VIEW]  
[BLOCK] appears next to the rat-  
ing category in the TV RATING  
menu.  
[BLOCK]  
[BLOCK]  
[BLOCK]  
4 Select your desired item  
Press Arrow (K/L) to point to your  
desired item.  
Then press ENTER to select  
[BLOCK] or [VIEW].  
B
TV–Y  
TV–Y7  
TV–G  
TV–PG (  
TV–14  
TV–MA(  
[VIEW]  
(
)
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
5 Exit the V-Chip setting mode  
Press SETUP on the remote control to return to orig-  
inal mode.  
)
)
)
(
EN  
17  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MPAA RATING SET UP  
CHANGE ACCESS CODE  
Make sure ...  
To change access code, follow the steps below.  
The unit is turned on.  
1 Select “V-CHIP SET UP”  
- TV SETUP -  
1 Select “V-CHIP SET UP”  
Press SETUP on the remote control.  
Press Arrow (K/L) to point to “V-  
CHIP SET UP”.  
Press SETUP on the remote con-  
- TV SETUP -  
CHANNEL SET UP  
trol.  
B
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
CHANNEL SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
B
Press Arrow (K/L) to point to “V-  
CHIP SET UP”.  
Then press ENTER.  
Then press ENTER.  
ACCESS CODE  
2 Enter 4-digit access code  
Press the number buttons. The  
default code is 0000.  
2 Enter 4-digit access code  
Press the number buttons. The  
default code is 0000.  
ACCESS CODE  
_
_
_
_
_
_
_
_
– V-CHIP SET UP –  
3 Select “CHANGE CODE”  
Press Arrow (K/L) to point to  
“CHANGE CODE".  
– V-CHIP SET UP –  
3 Select “MPAA RATING”  
Press Arrow (K/L) to point to  
“MPAA RATING”.  
TV RATING  
MPAA RATING  
CHANGE CODE  
TV RATING  
MPAA RATING  
CHANGE CODE  
B
B
Then press ENTER.  
Then press ENTER.  
4 Enter 4-digit access code  
Press the number buttons to enter  
your desired access code in the  
NEW CODE space. Then enter the  
same code in the CONFIRM  
4 Select your desired item  
Press Arrow (K/L) to point to your  
desired item.  
Then press ENTER to select  
[BLOCK] or [VIEW].  
NEW CODE  
G
[VIEW]  
PG  
[VIEW]  
_
_
_
_
_
PG–13  
R
NC–17  
X
[VIEW]  
B
[BLOCK]  
[BLOCK]  
[BLOCK]  
CONFIRM CODE  
_
_
_
CODE space. V-CHIP SET UP  
screen will appear on the screen.  
Selection  
G
Rating Category Explanations  
General Audience  
If you enter wrong code, repeat step [4], making  
sure you enter the same new code exactly in the  
confirm code space.  
PG  
PG-13  
R
Parental Guidance suggested.  
Unsuitable for children under 13  
Restricted; under 17 requires accompa-  
nying parent or adult guardian  
No one under 17 admitted  
5 Exit the V-Chip setting mode  
Press SETUP on the remote control to return to orig-  
inal mode.  
NC-17  
X
Mature audience only  
NOTE:  
When you select the rating category and set it to  
[BLOCK], the higher rating will change to  
[BLOCK] automatically. Also, the lower rating will  
change to [VIEW] automatically.  
When you set “G” to [VIEW], all ratings will  
change to [VIEW] automatically.  
If you unplug the power cord or a power failure  
occurs, the changed access code will be lost and  
will return to default (0000). Change your access  
code again as necessary.  
5 Exit the V-Chip setting mode  
Press SETUP on the remote control to return to origi-  
nal mode.  
EN  
18  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DVD SECTION  
ABOUT THE DISCS  
PLAYABLE DISCS  
DISC TYPES  
The following discs can be played back on this unit.  
[
]
DVD  
Data on a DVD is divided into sections called "titles" and  
then into subsections called "chapters", each of which is  
given a title or chapter number. Playback conditions are  
preset on some DVD video discs and these playback con-  
ditions take priority over user operations on this unit. If a  
function you selected does not run as desired, refer to the  
manual accompanying the disc.  
¡
¡
¡
¡
¡
¡
DVD video  
DVD+R/RW*  
CD-R/RW*  
DVD-R/RW*  
Audio CD  
MP3*  
* Depending on the types or the writing method of the  
medium some discs can not be played.  
• Some DVD-R/RW, DVD+R/RW or CD-R/RW discs  
made on personal computers or on DVD recorders may  
not be played back properly due to the factors such as  
scratches, dirt or special properties of the disc.  
• Discs made on personal computers may not be played  
back properly due to the different environment or the  
settings of the application you use. We recommend  
always to use the standardized, rightly formatted discs.  
(Please contact the sales agency for more detail).  
Example  
Title 1  
Title 2  
Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1 Chapter 2  
This unit conforms to the NTSC color system. You can-  
not play discs recorded in other color systems such as  
PAL or SECAM.  
[
]
AUDIO CD  
Data on an audio CD is divided into sections called  
“tracks”, each of which is given a track number.  
¡Some discs include region codes as shown below.  
Example  
Track 1  
Track 2  
Track 3  
Track 4  
Track 5  
Track 6  
¡The number inside the symbol refers to a region of the  
world and a disc encoded in a specific region format  
can only be played back on the unit with the same  
region code.  
[
]
MP3  
The following discs cannot be played back on this unit.  
Data on an MP3 is divided into sections called "groups",  
and then into subsections called "tracks", each of which is  
given a group or track number.  
¡
DVD with region codes other than 1 or ALL  
¡
¡
DVD-ROM  
DVD-RAM (Never play back, otherwise malfunc-  
tion may result.)  
Example  
Group 1  
Group 2  
¡
¡
¡
¡
¡
CD-ROM  
Track 1  
Track 2  
Track 3  
Track 4  
Track 5  
Track 6  
VSD  
CDV (Only plays back the audio part.)  
CD-G (Only plays back the sound.)  
CD-I (Never play back, otherwise malfunction  
may result.)  
¡
¡
SACD  
Photo CD (Never play back, otherwise malfunc-  
tion may result.)  
¡
¡
Video CD (Never play back, otherwise malfunc-  
tion may result.)  
DTS-CD  
Any other discs without compatibility indications.  
EN  
19  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PLAYING A DISC  
BASIC PLAYBACK  
GENERAL FEATURES  
DVD-V  
CD  
MP3  
DVD-V  
DVD may contain menus to navigate the disc and access  
special features. Press appropriate number buttons or  
Getting started  
¡Turn on the power of amplifier and any other com-  
use Arrow (  
K/L/s/B) to highlight your selection in the  
ponents, if necessary.  
DVD main menu and press ENTER to confirm.  
NOTES:  
¡Select DVD mode by pressing SELECT on the  
remote control. Then press PLAY or OPEN/CLOSE  
before you operate the DVD functions.  
1
Press POWER.  
¡The power will turn on.  
2
3
Press OPEN/CLOSE to open disc loading  
tray.  
¡Unless stated, all operations described are based on  
remote control use. Some operations can be carried  
out using the menu bar on the TV screen.  
Place the chosen disc in the tray, with the  
label facing up.  
DISC MENU  
DVD-V  
1
Press DISC MENU on the remote control.  
¡The DVD main menu will appear.  
2
3
If the feature is not available,  
may appear on the TV screen.  
symbol  
4
Press PLAY.  
¡The tray will close automatically and playback will  
then start from the first chapter or track of the disc.  
If the playback does not start automatically, press  
PLAY.  
If disc menu is available on the disc, audio  
language, subtitle options, chapters for the  
title and other options will appear for selec-  
tion.  
¡When you playback a DVD which features a title  
menu, it may appear on the screen. In this case, refer  
to “TITLE MENU”.  
4
Press Arrow (K/L/s/B) to select an item  
and ENTER to confirm selection.  
5
Press STOP to stop playback.  
TITLE MENU  
NOTES:  
¡When the DVD mode has been switched to the TV  
mode, the DVD mode shuts down first and then the  
TV picture and sound appears in about 4 seconds.  
Similarly, when POWER is pressed to turn off in the  
DVD mode, this mode shuts down first and then the  
unit’s power is turned off.  
¡A “prohibited icon” may appear at  
the top-right on the TV screen dur-  
ing operation, warning that a pro-  
hibited operation has been encoun-  
DVD-V  
1
Press TITLE on the remote control.  
¡The title menu will appear.  
2
3
If the feature is not available,  
may appear on the TV screen.  
symbol  
Press Arrow (K/L/s/B) to select an item  
and ENTER to confirm selection.  
tered by the DVD or the disc.  
¡With DVDs that use titles for playback program sig-  
nals, playback may start from the second title or it  
may skip these titles.  
¡During the playback of a two layered disc, pictures  
may stop for a moment. This happens when the 1st  
layer switches to the 2nd layer. This is not a mal-  
function.  
CALLING UP A MENU SCREEN  
DURING PLAYBACK  
¡Press DISC MENU to call up the DVD menu.  
¡Press TITLE to call up the title menu.  
NOTE:  
¡Contents of menus and corresponding menu opera-  
tions may vary between discs. Refer to the manual  
accompanying the disc for details.  
EN  
20  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FAST FORWARD/REVERSE  
SEARCH  
RESUME  
DVD-V  
CD  
MP3  
DVD-V  
CD  
MP3  
1
During playback, press STOP.  
¡Resume message will appear on the TV screen.  
1
During playback, press FWD  
¡g 1” or “h 1” appears on the screen.  
g
or REV  
h .  
2
Press PLAY, playback will resume from the  
point at which playback was stopped.  
2
To select another speed, repeat step [1] until  
your required speed appears on the screen.  
¡To cancel resume, press STOP twice.  
¡If the unit is turned off, resume function will be can-  
celled.  
¡For MP3, playback will resume from the beginning  
of the track at which playback was stopped.  
¡For DVDs, fast forward/reverse search speed is dif-  
ferent depending on the disc. Approximate speed is  
1(×2), 2(×8), 3(×50) and 4(×100).  
¡For audio CDs, approximate speed is ×16.  
¡For MP3, approximate speed is ×8  
¡
When you use buttons on the front panel, press and hold  
SKIPG / SEARCHg or SKIPH/ SEARCHh  
for a few seconds.  
PAUSE  
DVD-V  
CD  
MP3  
3
To return to normal playback, press PLAY.  
1
During playback, press PAUSE.  
¡Playback will pause and sound will be muted.  
SLOW FORWARD /  
SLOW REVERSE  
2
To continue playback, press PLAY.  
DVD-V  
1
2
During playback, press PAUSE.  
STEP BY STEP PLAYBACK  
Press FWD g or REV h .  
DVD-V  
¡“  
1” or “  
1” appears on the screen.  
3
To select another speed, repeat step [2] until  
your required speed appears on the screen.  
1
During playback, press PAUSE.  
¡Playback will pause and sound will be muted.  
¡Slow forward or reverse speed varies with the disc.  
Approximate speed is 1(1/16), 2(1/8) and 3(1/2).  
When you use buttons on the front panel, press and hold  
2
3
The disc goes forward by one frame each  
time PAUSE is pressed.  
¡
SKIP G/ SEARCH g or SKIP H/ SEARCH  
h
To exit step by step playback, press PLAY.  
for a few seconds.  
4
To return to normal playback, press PLAY.  
EN  
21  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SEARCH FUNCTION  
TRACK SEARCH  
TIME SEARCH  
CD  
MP3  
DVD-V  
CD  
There are three ways to begin playback on an Audio  
CD and MP3 at a specific track.  
1
2
During playback, press SEARCH MODE  
three times (CD: twice) to display the Time  
Search on the TV screen.  
Using the number buttons on the remote control  
Within 30 seconds, enter a desired disc  
time using the number buttons.  
1
Press the number buttons to enter the  
desired track number.  
¡Playback will start at the specified time.  
¡Press CLEAR to erase the incorrect input.  
¡When there is no need to enter a number, “0”  
appears automatically. For example, “ 0 : 0  
appears in the Time Search display if the total time  
of the disc is less than 10 minutes.  
¡Playback will start at the selected track.  
¡For single digit tracks (1-9), press a single number  
(eg. track 3, press 3).  
:
-
- -  
¡To play track 26, press +10, 2, 6.  
Using SEARCH MODE  
MARKER SETUP SCREEN  
1
Press SEARCH MODE.  
¡The Track search display appears.  
DVD-V  
CD  
2
Within 30 seconds, select a desired track  
number using the number buttons.  
Use markers to memorize your favorite places on a  
disc.  
¡For single digits press 0 first, if the total track of the  
disc is more than 10 tracks.  
¡Playback will start at the selected track.  
1
Press SEARCH MODE four times (CD: three  
times) during playback.  
Using SKIP  
H
G
¡The display screen and Markers will appear on the  
TV screen.  
During playback, press SKIP G to move the next  
track. Press it repeatedly to skip subsequent tracks.  
Press SKIP H to go back to beginning of the current  
track. Press it repeatedly to go to the previous tracks.  
¡If SKIP is pressed while the playback is paused, the  
playback will be paused again after skipping to the  
next track.  
2
3
Press Arrow (s /B) to select 1, 2, 3, 4, 5, 6,  
7, 8, 9, or 10 and ensure that “  
appears in the display.  
:
:
- - - - - - - -  
When you reach the desired point, press  
ENTER.  
NOTE:  
¡SKIP  
H
G are not available when playback is  
¡The title or track and elapsed playing time will  
appear in the TV screen.  
stopped.  
4
To return to the Marker later, press SEARCH  
MODE four times (CD: three times) during  
playback and Arrow (s /B) to choose the  
desired marker, then press ENTER.  
TITLE / CHAPTER SEARCH  
DVD-V  
NOTES:  
1
Press SEARCH MODE once for the Chapter  
search, twice for the Title search during  
playback.  
¡Opening the disc tray or turning off the power or  
selecting AC at step [2] and pressing ENTER will  
erase all Markers.  
_/2  
¡To clear a marker, using Arrow (s /B), position the  
cursor on to the marker number to be cleared and  
press CLEAR.  
¡You can mark up to 10 points.  
2
Enter the desired chapter/title number using  
the number buttons.  
¡Playback will start at the selected chapter or title.  
¡Press CLEAR to erase the incorrect input.  
¡For single digits press 0 first, if the total chapter or  
title of the disc is more than 10.  
5
Press SEARCH MODE or RETURN to exit.  
EN  
22  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPECIAL PLAYBACK FUNCTION  
REPEAT  
PROGRAM  
REPEAT is available only during playback.  
CD  
REPEAT TITLE / CHAPTER  
You may determine the order in which tracks will play.  
DVD-V  
1
In stop mode, press MODE.  
¡The PROGRAM screen will appear.  
To activate the repeat function, press REPEAT  
during playback.  
¡The repeat mode changes as described below every  
time you press the button.  
2
Press Arrow (/) to select a track, then  
press ENTER.  
¡Press CLEAR to erase the  
most recently entered pro-  
gram.  
TOTAL  
CHAPTER  
(current chapter repeat) (current title repeat)  
TITLE  
OFF  
(repeat off)  
NOTES:  
¡Repeat Title/Chapter is not available with some  
scenes.  
¡The REPEAT setting will be cleared when moving  
to other title or chapter.  
3
4
Repeat step [2] until you have selected all  
the tracks you want to play in the program.  
Press PLAY to play the programmed tracks.  
NOTES:  
REPEAT TRACK  
¡While the program is being played back, the STOP  
works as follows.  
CD  
¡Press STOP once and then PLAY again, playback  
will restart from the point where STOP was pressed.  
(Program continued)  
¡Press STOP twice and then PLAY again, playback will  
restart from the track in the usual way. (Program cleared)  
¡Up to 99 programs can be entered.  
To activate the repeat function, press REPEAT  
during playback.  
¡The repeat mode changes as described below every  
time you press the button.  
¡To erase all tracks in the program at once, select  
ALL CLEAR at the bottom of the list at Step [2].  
¡If you like to repeat the current track in the program,  
TRACK  
(current track repeat)  
ALL  
OFF  
(repeat off)  
(entire disc repeat)  
press REPEAT repeatedly until  
TRACK appears  
NOTES:  
during playback. If you like to repeat the entire pro-  
¡Repeat setting will be cleared when moving to other  
gram press REPEAT repeatedly until  
appears during playback.  
ALL  
track.  
¡Repeat playback does not function during repeat A-  
B playback.  
RANDOM PLAYBACK  
REPEAT A-B  
CD  
DVD-V  
CD  
This shuffles the playing order of tracks instead of  
playback in the sequence.  
1
2
Press REPEAT A-B at your chosen starting  
point.  
A- appears briefly on the TV screen.  
¡
¡
1
In stop mode, press MODE twice.  
¡RANDOM screen appears.  
RANDOM  
Press REPEAT A-B again at your chosen  
end point.  
A-B appears briefly on the TV screen and the  
CD-DA  
TOTAL 0:45:55  
RANDOM PROGRAM  
- - no indication - -  
repeat sequence begins.  
PLAY  
3
To exit the sequence, press REPEAT A-B.  
NOTES:  
2
Press PLAY to start random playback.  
NOTE:  
¡The repeat A-B section can only be set within the cur-  
rent title (for DVDs) or current track (for audio CDs).  
¡Repeat A-B is not available with some scenes in DVD.  
¡To cancel the A point which was set, press CLEAR.  
¡Repeat A-B playback does not function during title,  
chapter, track or all repeat playback.  
¡If you like to repeat the current track in the random  
selection, press REPEAT repeatedly until  
TRACK appears during playback. If you like to  
repeat the entire random selection press REPEAT  
repeatedly until  
ALL appears during playback.  
EN  
23  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PLAYING A MP3 DISC  
MP3 PLAYBACK  
PROGRAM  
MP3  
MP3  
When a CD with MP3 files is in the unit, press DISC This feature allows you to program an MP3 disc to  
MENU to call up the MP3 menu on the TV screen. play in a desired sequence.  
1
In stop mode, press Arrow (K/L) to select  
the desired group or track.  
1
In stop mode, press MODE.  
¡The PROGRAM screen will appear.  
¡If a group is selected, press  
B
or ENTER to go on to the  
track selection screen. Press  
Arrow (K/L) to choose a  
track, then press ENTER.  
¡If a track is selected, press  
ENTER to start playing  
tracks. Starting from the one you’ve just chosen the  
subsequent tracks will be played.  
¡Press TITLE to return to the first item.  
2
Select a desired track using Arrow  
(K/L/s/B). Then press ENTER.  
folder name 1  
folder name 2  
folder name 3  
folder name 4  
file name 1  
¡Press B when you want to go to the next hierarchy.  
¡Press s when you want to go back to the previous  
hierarchy.  
¡Press CLEAR to erase the most recently entered pro-  
gram.  
file name 2  
file name 3  
folder name 1  
3
Repeat step [2] until you have selected all  
the tracks you want to play in the program.  
2
Press STOP to stop playback.  
4
Press PLAY to start programmed playback.  
NOTES:  
NOTES:  
¡While the program is being played back, the STOP  
works as follows.  
¡Press STOP once and then PLAY again, playback  
will restart from the point where STOP was pressed.  
(Program continued)  
¡Press STOP twice and then PLAY again, playback will  
restart from the track in the usual way. (Program cleared)  
¡To erase all tracks in the program at once, select  
ALL CLEAR at the bottom of the list at Step [2].  
¡Folders are known as Groups; files are known as  
Tracks.  
3
¡MP3 files are accompanied by  
icon.  
¡Maximum of 255 folders can be recognized.  
¡Maximum of 512 files can be recognized.  
¡Up to 8 hierarchies can be created.  
This unit recommends the use of files recorded at the  
below specifications:  
¡Sampling frequency: 44.1kHz or 48kHz  
¡Constant bit rate: 112kbps ~ 320kbps.  
RANDOM PLAYBACK  
MP3  
REPEAT  
MP3  
1
In stop mode, press MODE twice.  
¡RANDOM screen appears.  
2
Press PLAY to start random playback.  
REPEAT is available only during playback.  
To activate the repeat function, press REPEAT  
during playback.  
¡The repeat mode changes as described below every  
time you press the button.  
TRACK  
(current track  
repeat)  
GROUP  
(current group  
repeat)  
ALL  
(entire disc  
repeat)  
OFF  
(repeat off)  
NOTE:  
¡Repeat setting will be cleared when moving to other  
track.  
EN  
24  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CHANGING THE SETTINGS  
SUBTITLE LANGUAGE  
CAMERA ANGLE  
DVD-V  
DVD-V  
The unit allows you to select a language for subtitles Some DVD discs contain scenes which have been shot  
during DVD disc (if available) playback. simultaneously from various angles. You can change  
the camera angle when the (  
screen.  
) icon appears on the  
1
2
Press SUBTITLE during playback.  
Press SUBTITLE repeatedly to select your  
desired subtitle language.  
1
Press ANGLE during playback.  
¡The selected angle will be displayed on the display  
¡The subtitle language will be displayed on the dis-  
play bar at the top of the screen.  
bar at the top of the screen.  
2
Press ANGLE repeatedly to select your  
desired angle.  
3
To turn off subtitles, press SUBTITLE  
repeatedly until OFF appears.  
NOTES:  
¡
Some discs allow audio language setting/subtitle language  
setting on the disc menu. (Operation varies between discs,  
so refer to the manual accompanying the disc.)  
BLACK LEVEL SETTING  
DVD-V  
¡If the desired language is not shown after pressing  
SUBTITLE several times, the disc does not have  
subtitles in that language.  
Adjust the Black Level Settings to make the black  
parts of the picture brighter.  
¡If you choose a Language that has a 3 letter language  
code, the code will be displayed every time you  
change the Subtitle language setting. If you choose  
any other languages, ‘---’ will be displayed instead.  
(Refer to page 27.)  
1
Press MODE during playback.  
OFF  
2
Press ENTER to switch ON/OFF.  
ON: Makes the dark parts brighter.  
AUDIO LANGUAGE  
OFF: Shows the original picture as recorded.  
DVD-V  
3
Press MODE twice or RETURN to exit.  
NOTE:  
The unit allows you to select a language during DVD  
disc (if multi languages are available) playback.  
¡The setting will be saved even if the unit is turned off.  
1
2
Press AUDIO during playback.  
VIRTUAL SURROUND  
Press AUDIO repeatedly to select your  
desired language.  
DVD-V  
CD  
MP3  
NOTE:  
¡Pressing AUDIO may not work on some DVDs with  
multiple audio languages (e.g. DVDs which allow  
audio language setting on the disc menu).  
You can enjoy surround-sound effect over two speak-  
ers on this unit.  
1
Press V.SURR once or MODE twice  
(CD/MP3: once) during playback.  
STEREO SOUND MODE  
CD  
OFF  
1
Press AUDIO repeatedly during playback to  
select between STEREO, L-CH or R-CH.  
2
3
Press ENTER to set it 1 (Natural effect) or 2  
(Emphasized effect) or OFF.  
¡STEREO - both right and left channels are active  
(stereo)  
L-CH - only left channel is active  
R-CH - only right channel is active  
NOTE:  
¡If the Virtual Surround setting is ON, the sound mode  
will be fixed to STEREO and can not be changed.  
Press V.SURR or MODE or RETURN to exit.  
NOTE (for CD play only):  
¡Virtual Surround will not be effective if the sound  
mode is set to something other than STEREO.  
EN  
25  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
THE ON-SCREEN INFORMATION  
DVD-V  
CD  
MP3  
You can check the information about the current disc by pressing DISPLAY on the remote control.  
For DVD-Vs  
For audio CDs  
1
Press DISPLAY during playback to show  
current Chapter.  
1
Press DISPLAY during playback to show the  
current Track.  
¡The elapsed and remaining  
playing time of the current  
chapter will be displayed.  
¡The elapsed and remaining playing time of the cur-  
rent track will be displayed.  
9/49  
0:00:00 -0:03:30  
2
Press DISPLAY again to show current Total  
Track.  
2
Press DISPLAY again to show current Title.  
¡The elapsed and remaining playing time of the cur-  
¡The elapsed and remaining playing time of the cur-  
rent track will be displayed.  
rent title will be displayed.  
3
Press DISPLAY again.  
¡The BIT RATE and the current repeat setting will be  
displayed.  
3
Press DISPLAY again to exit the display.  
¡If you are playing a dual layered disc, the layer num-  
ber will also be displayed (L0: Layer 0 is playing.  
L1: Layer 1 is playing).  
For MP3  
1
Press DISPLAY during playback.  
¡The name of the file currently in play will be dis-  
4
Press DISPLAY again to exit the display.  
played.  
2
Press DISPLAY again to show the track  
number, the elapsed time, the repeat status  
and the playback status at the top of the  
screen.  
¡
will be displayed when repeat play has been  
selected.  
T - indicates Track repeat  
G - indicates Group (folder) repeat  
A - indicates Disc repeat  
3
Press DISPLAY again to exit the display.  
EN  
26  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CHANGING THE DVD SETUP ITEMS  
LANGUAGE SETTING  
Language  
Code Language  
Code  
DVD-V  
A-B  
L-N  
Abkhazian  
Afar  
Afrikaans  
Albanian  
Amharic  
Arabic  
Armenian  
Assamese  
Aymara  
Azerbaijani  
Bashkir  
Basque  
Bengali;Bangla  
Bhutani  
Bihari  
Bislama  
Breton  
4748 Laothian  
4747 Latin  
4752 Latvian;Lettish  
6563 Lingala  
4759 Lithuanian  
4764 Macedonian  
5471 Malagasy  
4765 Malay  
5861  
5847  
5868  
5860  
5866  
5957  
5953  
5965  
5958  
5966  
5955  
5964  
5961  
5960  
6047  
6051  
6061  
Language options are not available with some discs.  
1
Press SETUP twice in STOP mode so that  
the DVD SETUP menu appears.  
¡If the menu does not appear, press PLAY, STOP,  
4771 Malayalam  
4772 Maltese  
4847 Maori  
then SETUP twice.  
5167 Marathi  
SETUP  
4860 Moldavian  
5072 Mongolian  
4854 Nauru  
QUICK  
CUSTOM  
INITIALIZE  
4855 Nepali  
4864 Norwegian [NOR]  
4853  
5971 Occitan  
4851 Oriya  
Oromo(Afan)  
5759 Panjabi  
4947 Pashto;Pushto  
7254 Persian  
4961 Polish  
5464 Portuguese [POR]  
4965 Quechua  
5047 Rhaeto-Romance  
6058 Romanian [RUM]  
5160 Russian [RUS]  
5161  
5166 Samoan  
Sangho  
5261 Sanskrit  
5256 Scots Gaelic  
5255 Serbian  
Bulgarian  
Burmese  
Byelorussian  
O-R  
6149  
6164  
6159  
6247  
6265  
5247  
6258  
6266  
6367  
6459  
6461  
6467  
2
Press Arrow L to select “CUSTOM”, then  
C-E  
press ENTER.  
Cambodian  
Catalan  
¡CUSTOM mode will appear.  
Chinese [CHI]  
Corsican  
Croatian  
3
Press Arrow (K/L) to select “LANGUAGE”,  
Czech  
then press ENTER to confirm.  
Danish [DAN]  
Dutch [DUT]  
English [ENG]  
Esperanto  
Estonian  
SETUP  
CUSTOM  
S
6559  
6553  
6547  
5350  
6564  
6554  
6566  
6660  
6560  
6550  
6555  
6565  
6557  
6558  
6561  
5165  
6567  
6569  
6568  
LANGUAGE  
DISPLAY  
AUDIO  
F-H  
Faroese  
Fiji  
PARENTAL  
Finnish [FIN]  
French [FRE]  
Frisian  
5264 Serbo-Croatian  
5271 Sesotho  
5358 Setswana  
5747 Shona  
4
Press Arrow (K/L) to select the next items,  
Galician  
then press ENTER.  
Georgian  
German [GER]  
Greek [GRE]  
Greenlandic  
Guarani  
5051 Sindhi  
AUDIO: Sets the audio language.  
5158 Singhalese  
5758 Siswat  
5360 Slovak  
SUBTITLE: Sets the subtitle language.  
DISC MENU: Sets the language for DVD menu.  
Gujarati  
Hausa  
Hebrew  
5367 Slovenian  
5447 Somali  
5569 Spanish [SPA]  
5455 Sundanese  
5467 Swahili  
5
Press Arrow (K/L) to select a setting, then  
press ENTER.  
Hindi  
Hungarian [HUN]  
I-K  
Icelandic [ICE]  
Indonesian  
Interlingua  
Interlingue  
Inupiak  
Swedish [SWE]  
¡If OTHER is selected on the AUDIO, SUBTITLE or  
DISC MENU screen, press four-digit number to  
enter the code for the desired language. (Refer to the  
language code list.)  
¡Only the languages supported by the disc can be  
selected.  
5565  
5560 Tagalog  
5547 Tajik  
5551 Tamil  
5557 Tatar  
5347 Telugu  
5566 Thai  
T
6658  
6653  
6647  
6666  
6651  
6654  
4861  
6655  
6661  
6665  
6664  
6657  
6669  
Irish [IRI]  
Italian [ITA]  
Japanese [JPN]  
Javanese  
Kannada  
Kashmiri  
5647 Tibetan  
5669 Tigrinya  
5760 Tonga  
5765 Tsonga  
5757 Turkish [TUR]  
6469 Turkmen  
5771 Twi  
6
Press SETUP to exit.  
Kazakh  
NOTE:  
Kinyarwanda  
Kirghiz  
Kirundi  
¡Language Setting for Audio and Subtitle is not avail-  
able with some discs. Then use the AUDIO and the  
SUBTITLE button. (Details are on page 25.)  
6460  
U-Z  
Korean [KOR]  
Kurdish  
5761 Ukrainian  
5767 Urdu  
Uzbek  
6757  
6764  
6772  
6855  
6861  
4971  
6961  
7054  
5655  
7161  
7267  
Vietnamese  
Volapuk  
Welsh  
Wolof  
Xhosa  
Yiddish  
TO CHANGE THE ON-SCREEN MENUS  
You can access the TV SETUP menu by pressing  
SETUP from the DVD mode. Refer to “Selecting the  
Language” on page 13 to changing the on-screen  
menus.  
Yoruba  
Zulu  
If you choose a Language that has a 3 letter language  
code, the code will be displayed every time you change  
the Audio or Subtitle language setting on page 25. If  
you choose any other languages, ‘---’ will be displayed  
instead. (3 letter language code is written in bracket.)  
EN  
27  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DISPLAY SETTING  
AUDIO SETTINGS  
DVD-V  
DVD-V  
You can change certain aspects of the DVD display  
screens and on-screen messages on the TV screen.  
Choose the appropriate Audio settings for your equip-  
ment as it only affects during the playback of DVD  
discs.  
1
Press SETUP twice in STOP mode so that  
the DVD SETUP menu appears.  
1
Press SETUP twice in STOP mode so that  
the DVD SETUP menu appears.  
¡If the menu does not appear, press PLAY, STOP,  
then SETUP twice.  
¡If the menu does not appear, press PLAY, STOP,  
then SETUP twice.  
SETUP  
SETUP  
QUICK  
CUSTOM  
INITIALIZE  
QUICK  
CUSTOM  
INITIALIZE  
2
Press Arrow L to select “CUSTOM”, then  
press ENTER.  
2
Press Arrow L to select “CUSTOM”, then  
press ENTER.  
¡CUSTOM mode will appear.  
¡CUSTOM mode will appear.  
3
Press Arrow (K/L) to select “DISPLAY”,  
then press ENTER to confirm.  
3
Press Arrow (K/L) to select “AUDIO”, then  
press ENTER to confirm.  
SETUP  
CUSTOM  
LANGUAGE  
DISPLAY  
AUDIO  
SETUP  
CUSTOM  
PARENTAL  
LANGUAGE  
DISPLAY  
AUDIO  
4
Press Arrow (K/L) to select the below  
items, then press ENTER.  
PARENTAL  
TV MODE:  
QUICK  
4
Press Arrow (K/L) to select the below  
items, then press ENTER.  
¡Press Arrow (K/L) for an item selection, then press  
ENTER.  
¡Select 4:3 LETTER BOX for black bars to appear on  
top and bottom of the screen.  
DRC (Dynamic Range Control):  
¡To compress the range of sound volume.  
¡The default setting is ON.  
¡Select 4:3 PAN & SCAN for a full height picture  
with both sides trimmed.  
¡The default setting is 4:3 LETTER BOX.  
DOWN SAMPLING:  
¡Set to ON when outputting in 48 kHz.  
¡The default setting is ON.  
When playing disc with copyright Protection  
¡If you select OFF, copyright protection will be acti-  
vated and sound will be down sampled at 48kHz.  
STILL MODE:  
¡Press Arrow (K/L) for an item selection, then press  
ENTER.  
¡Select “AUTO” usually.  
¡If you select “FIELD”, the picture in the still mode  
will be stabilized.  
¡If you select “FRAME”, the picture in the still mode  
will be highly defined.  
DOLBY DIGITAL:  
Set to On when the unit is connected to a Dolby Digital  
Decoder.  
(ON: Output by Dolby Digital)  
(OFF: Convert the Dolby Digital to PCM (2 channel  
stereo))  
QUICK  
ANGLE ICON:  
¡Press ENTER repeatedly to turn Angle icon ON or  
OFF.  
¡The default setting is ON.  
AUTO POWER OFF:  
¡The default setting is ON.  
¡Press ENTER repeatedly to turn Auto Power off ON  
or OFF.  
5
Press SETUP to exit.  
¡
The default setting is ON and the screen saver program  
starts when there is no input from the unit for 5 minutes  
in the stop mode. When the screen saver program is  
activated for 15 minutes, the power automatically turns  
off.  
5
Press SETUP to exit.  
EN  
28  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTROL LEVELS  
PARENTAL CONTROL  
¡
ALL  
All parental lock is cancelled.  
DVD-V  
¡
Level 8  
DVD software of any grade (adult/general/children)  
can be played back.  
Parental Control limits the disc viewing that exceed  
your settings (with a password or playback will stop).  
This feature allows you to prevent discs with alterna-  
tive scenes from being played by your children.  
¡
Levels 7 to 2  
Only DVD software intended for general use and  
children can be played back.  
¡
Level 1  
PARENTAL LEVEL  
Only DVD software intended for children can be  
played back, with those intended for adult and  
general use is prohibited.  
Parental Level allows you to set the rating level of  
your DVD discs. Playback will stop if the disc’s rat-  
ings exceed the level you set.  
1
Press SETUP twice in STOP mode so that  
the QUICK SETUP menu appears.  
IF YOU FORGET THE PASSWORD  
¡If the menu does not appear, press PLAY, STOP,  
1
Press 4, 7, 3, 7 at step [4]. Then enter your  
new password.  
then SETUP twice.  
SETUP  
¡Password will be cleared and parental level will be  
set to ALL.  
QUICK  
CUSTOM  
INITIALIZE  
2
Follow Steps [5]-[7] again.  
2
3
Press Arrow L to select “CUSTOM”, then  
press ENTER.  
INITIALIZE  
This allows you to return all selections of SETUP  
(except for PARENTAL) to their default settings.  
Press Arrow (K/L) to select “PARENTAL,  
then press ENTER.  
1
2
3
Press SETUP twice in STOP mode so that  
the INITIALIZE menu appears.  
SETUP  
CUSTOM  
LANGUAGE  
DISPLAY  
AUDIO  
Press Arrow (K/L) to select “INITIALIZE”,  
then press ENTER.  
PARENTAL  
Select “YES”, then press ENTER twice. All  
the settings (except for “PARENTAL) will be  
cleared.  
4
5
6
7
Enter your four-digit password then press  
ENTER.  
¡To cancel the initialization, select “NO”.  
Press Arrow (K/L) to select PARENTAL  
LEVEL, then press ENTER.  
4
Press SETUP to exit.  
Press Arrow (K/L) to select the desired  
level, then press ENTER.  
Press SETUP to exit  
NOTES:  
¡When doing this for the first time, enter any 4 digits.  
(except for 4737) That number will be used as the  
password from the second time onward.  
¡To change the password, press Arrow (K/L) to  
select CHANGE at step [5], then press ENTER.  
Enter the four-digit password, then press ENTER.  
¡With some DVDs, it may be difficult to find if they  
are compatible with parental lock. Be sure to check  
if the parental lock function operates in the way that  
you have set.  
¡Record the password in case you forget it.  
EN  
29  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING GUIDE  
If the unit does not perform properly when operated as instructed in this Owner’s Manual, check the unit, con-  
sulting the following checklist.  
Problem  
Corrective Action  
Make sure the power plug is connected to an AC outlet.  
Make sure the power is turned on.  
Check if the power plug is connected to an AC outlet.  
Check the batteries in the remote control.  
Aim the remote control directly at the remote sensor. If necessary,  
remove all the obstacles between the sensor and the remote.  
You have to be within 23 feet of the unit.  
No power  
The unit does not respond to  
the remote control.  
Check if the correct mode is selected. If not switch the mode by  
pressing SELECT on the remote control,whichever you need.  
TV Mode  
Problem  
Corrective Action  
No Picture or Sound  
Try a new channel, if OK, then possible station trouble.  
Make sure the power is turned on.  
Press SELECT on the remote control to select TV mode. Then try  
other TV feature.  
Is antenna connected to terminal on the back of the set?  
If outside antenna is being used, check for broken wire.  
If outside antenna is being used, check for broken wire.  
Check for local interference.  
Try a new channel, if OK, then possible station trouble.  
If outside antenna is being used, check for broken wire.  
Try a new channel, if OK, then possible station trouble.  
If outside antenna is being used, check for broken wire.  
Check for local interference.  
Try a new channel, if OK, then possible station trouble.  
Is antenna connected to terminal on the back of the set?  
If outside antenna is being used, check for broken wire.  
Adjust COLOR control.  
Try a new channel, if OK, then possible station trouble.  
Is antenna connected to terminal on the back of the set?  
If outside antenna is being used, check for broken wire.  
Check for local interference.  
Try a new channel, if OK, then possible station trouble.  
Is antenna connected to terminal on the back of the set?  
If outside antenna is being used, check for broken wire.  
Adjust CONTRAST & BRIGHT control.  
Try a new channel, if OK, then possible station trouble.  
Is antenna connected to terminal on the back of the set?  
If outside antenna is being used, check for broken wire.  
Check for local interference.  
Bars On Screen  
Picture Distorted or Blurred  
Picture Rolls Vertically  
Lines or Streaks in Picture  
No Color  
Poor Reception on Some Channels  
Ghosts in Picture  
Weak Picture  
Sound OK, Picture Poor  
Adjust CONTRAST & BRIGHT control.  
Try a new channel, if OK, then possible station trouble.  
Check for local interference.  
Magnetism from nearby appliances and geomagnetism might affect  
the color of the TV picture. Move the unit away from the appliances,  
the unit can repair itself automatically. If you want to repair immedi-  
ately, unplug the unit power cord, then plug it in again 30 minutes or  
so later. This automatically resets the unit.  
Picture OK, Sound Poor  
Different color marks on screen  
EN  
30  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Closed Caption Problem  
My unit is showing captions  
that are misspelled.  
Possible Remedy  
You are watching a live broadcast and spelling errors made by the  
closed captioning production company may pass through uncorrected.  
A prerecorded program will not show any misspelled words because  
of the normal time available for editing the captions.  
My unit will not show the text  
• Captions that are delayed a few seconds behind the actual dialogue  
in its entirety or there is a delay of are common for live broadcast. Most captioning production companies  
what is being said.  
can display a dialogue to a maximum of 220 words per minute. If a  
dialogue exceeds that rate, selective editing is used to insure that the  
captions remain up-to-date with the current TV screen dialogue.  
• Interference caused by building, power lines, thunderstorms, etc.  
may cause scrambled or incomplete captions to appear.  
My captions are scrambled with  
white boxes on the TV screen.  
My program guide listed a TV show • Broadcasters may at times use a time compression process to the  
as being closed captioned but none actual program so that additional advertising time can be given.  
of the captions were displayed.  
Since the decoder cannot read the compressed information,  
captions will be lost.  
My unit screen shows a black  
box on certain channels.  
You are in the TEXT mode. Select CAPTION mode or CAPTION  
[OFF].  
DVD Mode  
Problem  
Corrective Action  
• Insert a correct video disc that plays on this unit.  
• Press SELECT on the remote control to select DVD mode. Next,  
press PLAY or OPEN/CLOSE. Then, try other DVD feature.  
• Insert the disc.  
No picture  
Disc cannot be played  
No sound  
• Clean the disc.  
• Place the disc correctly, with the label side up.  
• Cancel the parental lock or change the control level.  
• Connect the audio cables firmly.  
• Turn the power of the audio component on.  
• Correct the audio output settings.  
• Correct the input settings on the audio component.  
• This unit does not support DTS audio. This is not a malfunction.  
• There are some cases where pictures may be slightly distorted, which  
are not a sign of a malfunction.  
No DTS audio is output  
Distorted picture  
• Although pictures may stop for a moment, this is not a malfunction.  
• The selected language is not available for audio or subtitles on the  
DVD.  
Audio or subtitle language  
does not match the set up  
This is not a malfunction  
The camera angle cannot be  
changed  
• The DVD does not contain sequences recorded from different camera  
angles. This is not a malfunction  
Audio or subtitle language cannot  
be changed  
• The DVD does not contain audio source or subtitles in the selected  
language. This is not a malfunction.  
“Prohibited icon” appears on the  
screen, prohibiting an operation  
CD sound dropout  
• That operation is prohibited by the unit or the disc.  
This is not a malfunction.  
• Scratched disc. Replace the disc with an unscratched one.  
No CD reproduction  
DVD picture dropout  
DVD picture freeze  
DVD picture in mosaic  
No DVD reproduction  
NOTES:  
Some functions are not available in specific modes, but this is not a malfunction. Read the description in  
this Owner’s Manual for details on correct operations.  
Playback from a desired track and random playback are not available during program playback.  
EN  
31  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
CABINET CLEANING  
SERVICING  
Wipe the front panel and other exterior surfaces of  
the unit with a soft cloth immersed in lukewarm  
water and wrung dry.  
Never use a solvent or alcohol. Do not spray insec-  
ticide liquid near the unit. Such chemicals may  
cause damage and discoloration to the exposed sur-  
faces.  
Should your unit become inoperative, do not try to  
correct the problem by yourself. There are no user-  
serviceable parts inside. Turn off, unplug the power  
cord and please call our help line at 1-800-242-  
7158, to locate an Authorized Service Center.  
IF THE LASER OPTICAL PICKUP UNIT IS DIRTY  
If the unit still does not perform properly when it is operated, while referring to the relevant sections and to  
"TROUBLESHOOTING GUIDE" in this Owner's Manual, the laser optical pickup unit may be dirty. Consult  
your dealer or an Authorized Service Center for inspection and cleaning of the laser optical pickup unit.  
DISC HANDLING  
Use discs which have the following logos on them.  
(Optical audio digital discs.)  
To clean-off, use a soft cloth.  
Do not use a hard cloth since this will mar the disc.  
Wipe the disc in a straight line from center to edge.  
Never wipe with a circular motion.  
Do not use detergent or abrasive cleaning agents.  
ReWritable  
Recordable  
Handle the discs so that fingerprints and dust do  
not adhere to the surfaces of the discs.  
Always store the disc in its protective case when it  
is not used.  
EN  
32  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPECIFICATIONS  
GENERAL SPECIFICATIONS  
ELECTRICAL SPECIFICATIONS  
Sound output:  
2 speakers, 1W, 8 ohm  
TV  
CRT :  
20 inch in-line gun,  
90˚ deflection tube  
NTSC-M  
OTHER SPECIFICATIONS  
Terminals  
Television system:  
Antenna input:  
VHF/UHF/CATV  
TV Standard  
75 ohm unbalanced (F-type)  
RCA connector [ 1  
RCA connector [ 2  
Closed caption system: §15.119/FCC  
Channel coverage:  
Video input:  
Audio L/R input:  
Headphone:  
Coaxial digital  
audio output  
(only DVD):  
VHF:  
UHF:  
CATV:  
2 ~ 13  
14 ~ 69  
2 ~13, A ~ W,  
W+1 ~ W+84,  
A-5 ~ A-1, 5A  
181 channel  
1/8” stereo (3.5 mm)  
One pin jack,  
500m Vpp (75 ohm)  
Digital encoded  
Tuning System:  
Channel access:  
Remote control:  
frequency synthesized  
tuning system  
Direct access keyboard,  
programmable  
scan and up/down  
infrared light system  
Operating  
temperature:  
5°C to 40°C  
(41°F~104°F)  
Power requirements: AC 120V, 60Hz  
Power consumption  
(Maximum) :  
Dimensions :  
80W  
H:20-3/16”(513.5mm)  
W:20-3/16”(512mm)  
D:19-13/16”(503mm)  
49.6lbs(21.0kg)  
DVD  
Weight :  
Discs:  
DVD video, Audio CD  
Output signal format: NTSC color  
Designs and specifications are subject to change without notice.  
If there is a discrepancy between languages, the default language will be English.  
EN  
33  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9. Botón SKIP  
H
INDICE  
Reproduce desde el inicio del capítulo o canción actual.  
Botón SEARCH (REV) h (panel delantero)  
Durante la reproducción o en el modo de pausa,  
mantenga presionado el botón durante unos segundos  
para cambiar la velocidad de reproducción hacia atrás.  
CONTROLES DE OPERACIÓN Y FUNCIONES . . . . . 34  
PANEL FRONTAL DEL TELEVISOR/DVD. . . . . . . . . . 34  
MANDO A DISTANCIA. . . . . . . . . . . . . . . . . . . . . . . . . 34  
VISTA POSTERIOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34  
PARA INSERTAR LAS PILAS . . . . . . . . . . . . . . . . . . . . 35  
PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 35  
CONEXIONES DE ANTENA/CABLE . . . . . . . . . . . . . . 35  
CONEXIÓN A TOMAS DE ENTRADA EXTERNA. . . . 36  
CONEXIÓN A UN AMPLIFICADOR EQUIPADO  
10. Botón PLAY  
Inicia la reproducción del contenido del disco.  
Púlselo para cambiar a un modo de DVD cuando esta  
en el modo de televisor.  
11. Botón SKIP  
G
CON TOMAS DE ENTRADA DIGITAL, PLATINA  
MD O PLATINA DAT (Para DVD) . . . . . . . . . . . . . . . . . 36  
CONEXCIONA UN DECODIFICADOR DOLBY  
Reproduce desde el inicio del siguiente capítulo o  
canción.  
Botón SEARCH (FWD) g (panel delantero)  
Durante la reproducción o en el modo de pausa,  
mantenga presionado el botón durante unos segundos  
para cambiar la velocidad de reproducción en avance.  
DIGITAL (Para DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37  
TV SECTION  
PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 37  
SELECCIÓN DE IDIOMA . . . . . . . . . . . . . . . . . . . . . . . 37  
AJUSTE DE CANAL . . . . . . . . . . . . . . . . . . . . . . . . . . . 38  
12. Botón PAUSE  
Hace una pausa en la operación del disco.  
13. Botón OPEN/CLOSE  
Púlselo para insertar discos en la bandeja o retirarlos  
de ella.  
DVD SECTION  
REPRODUCCIÓN DE UN DVD DE VÍDEO O UN  
CD DE AUDIO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38  
REPRODUCCION BASICA . . . . . . . . . . . . . . . . . . . . . . 38  
14.Toma HEADPHONE  
Para conectar auriculares (no suministrados) y  
escuchar en privado.  
CONTROLES DE  
15. Botón MODE  
Activa el modo de reproducción programada o el  
modo de reproducción aleatoria cuand se reproducen  
CDs o MP3.  
OPERACIÓN Y FUNCIONES  
PANEL FRONTAL DEL  
TELEVISOR/DVD  
16. Botones de números  
Modo del televisor:  
Pulse dos dígitos para tener acceso directamente al  
canal deseado.  
Consulte la figura 1 de la página 8  
Recuerde pulsar "0" antes de elegir un canal de un  
solo dígito.  
MANDO A DISTANCIA  
Botón +100  
Púlselo para seleccionar canales de televisión por  
cable cuyo número sea igual o superior al 100.  
Modo DVD:  
Consulte la figura 2 de la página 8  
VISTA POSTERIOR  
Púlselo para introducir el número deseado.  
Botón +10  
Púlselo para introducir los números deseados cuyo  
número sea igual o superior al 10.  
Consulte la figura 3 de la página 9  
1. Bandeja de carga del disco  
17. Botón SLEEP  
2.Toma de entrada VIDEO  
Pulse el botón SLEEP para visualizar el temporizador  
para dormir y activar la función. La hora de apagado  
puede determinarse por el número de veces que usted  
pulsa el botón. (0, 30, 60, 90 o 120 minutos)  
Conecte aquí la toma de salida de vídeo de una  
videocámara o de una videograbadora.  
3.Tomas de entrada AUDIO L/R  
18. Botón REV  
h
Conecte aquí las tomas de salida de audio de una  
videocámara o de una videograbadora.  
Presione para ver la imagena en DVD en retroceso  
rápido. Presione PAUSE y presione este botón para  
empezar la reproducción en cámara lenta. Presione  
repetidamente este botón para cambiar la velocidad en  
avance de la cámara lenta.  
4. Botón POWER  
Púlselo para conectar y desconectar la alimentación.  
5. Botones VOLUME K/L(VOL.  
m
/
n)  
Púlselos para controlar el nivel del volumen para el  
DVD y el televisor.  
Botón FWD  
g
Presione para avanzar rápidamente en el disco.  
Presione PAUSE y presione este botón para empezar  
la reproducción en cámara lenta. Presione  
repetidamente este botón para cambiar la velocidad  
de avance de la cámara lenta.  
6. Botones CHANNEL K/L(CH. K/L)  
Púlselo para seleccionar el canal memorizado.  
Púlselo para cambiar a un modo de televisor cuando  
esta en el modo de DVD.  
7. Ventanilla del sensor del mando a distancia  
19. Botón V.SURR  
8. Botón STOP  
Púlselo para activar/desactivar el envolvente virtual.  
Detiene la operación del disco.  
20. Botón SETUP  
Púlselo para activar o salir del modo de menús de  
televisor o preparación de DVD.  
ES  
34  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
21. Botón TITLE  
37. Cable de alimentaciónConéctelo a una toma de  
CA convencional (120 V/60 Hz).  
Visualiza el menú de títulos.  
NOTA: Retire el cable de alimentación del gancho  
para evitar romperlo antes de conectarlo a una  
toma de CA convencional.  
22. Botón CLEAR  
Repone un ajuste.  
23. Botón DISPLAY  
38.Toma de salida de audio digital COAXIAL  
(DVD Audio solamente)  
Modo del televisor:  
Púlselo para visualizar el número del canal en la  
pantalla. Si lo pulsa de nuevo, el número del canal  
desaparecerá.  
Conéctela a la entrada digital de un amplificador o  
decodificador externo.  
Modo de DVD:  
Visualiza el estado actual en la pantalla del televisor  
con fines de comprobación.  
39.Toma de entrada ANT.  
Conéctela a una antena, sistema de televisión por  
cable o sistema de satélite.  
24. Botón SEARCH MODE  
Púlselo para localizar un punto deseado.  
PARA INSERTAR LAS PILAS  
1) Abra la cubierta del compartimiento de las pilas  
empujando la cubierta del mando a distancia en el  
sentido de la flecha.  
2) Inserte 2 pilas "AA" en el compartimiento de las  
pilas, en el sentido indicado por las marcas de  
polaridad (+/-).  
25. Botón AUDIO  
Púlselo para seleccionar un idioma de audio o un  
modo de sonido deseado.  
26. Botón SUBTITLE  
Púlselo para seleccionar un idioma de subtítulos  
deseado.  
27. Botón REPEAT  
Repite la reproducción del disco, título, capítulo,  
groupo o pista actual.  
3) Vuelva a poner la cubierta.  
28. Botón ANGLE  
NOTAS:  
Púlselo para cambiar el ángulo de la cámara y ver,  
desde un ángulo diferente, la secuencia que está  
siendo reproducida.  
No mezcle pilas alcalinas y de manganeso.  
No mezcle pilas viejas y nuevas.  
29. Botón A-B REPEAT  
Repite la reproducción de una sección seleccionada.  
30. Botón RETURN  
PREPARACIÓN PARA LA  
UTILIZACIÓN  
Vuelve a la operación anterior en el modo de  
instalación del DVD.  
31. Botón ENTER  
Púlselo para establecer un ajuste.  
CONEXIONES DE  
ANTENA/CABLE  
32. Botones de flechas  
Modo de televisor:  
Púlselo para seleccionar un modo de ajuste desde el  
menú que aparece en la pantalla del televisor.  
Púlselo para seleccionar o ajustar desde un menú  
particular.  
Consulte la figura 4 de la página 10  
Nota para el instalador de sistemas CATV  
Esta nota tiene la finalidad de llamar la atención del  
instalador de sistemas CATV para que tenga en  
cuenta el Artículo 820-40 del NEC, el cual  
proporciona consejos para hacer una conexión a  
tierra apropiada y, en particular, especifica que la  
tierra del cable deberá estar conectada al sistema de  
puesta a tierra del edificio, tan cerca del punto de  
entrada del cable como sea posible.  
Modo de DVD:  
Se utiliza cuando se hacen ajustes mientras se  
observa la visualización en una pantalla de televisor.  
33. Botón DISC MENU  
Visualiza menús en el DVD.  
34. Botón SELECT  
Púlselo para cambiar a un modo de televisor, modo  
de entrada externa o modo de DVD.  
NOTA: Cuando seleccione el modo DVD con  
este botón, pulse primero PLAY u  
NOTA:  
Antes de enchufar la antena a la toma ANT.IN del  
televisor/DVD, compruebe que la clavija no esté  
doblada. Si esta doblada, póngala derecha como se  
muestra en la ilustración, y luego conéctela en la  
toma ANT.IN del televisor/DVD.  
Clavija doblada  
OPEN/CLOSE. De lo contrario, las funciones del  
DVD no se activarán.  
35. Botón MUTE  
Pulse el botón MUTE para apagar el sonido de un  
programa de TV. (La visualización del nivel del  
sonido cambia de ROJO CLARO a AZUL CLARO.)  
Pulse de nuevo el botón MUTE o el botón VOL m o  
n para restaurar el sonido.  
Cable  
Clavija  
(Necesita enderezarse)  
(Clavija derecha)  
36. Botón PICTURE  
Presione para entrar en el modo de ajuste de imagen.  
ANTENA COMBINADA DE VHF/UHF  
La antena combinada de VHF/UHF de 75 ohmios  
puede conectarse al terminal ANT.  
ES  
35  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTA:  
Cuando conecte una videograbadora monofónica  
(otra fuente) a este televisor/DVD, conecte la toma  
de salida de audio de la videograbadora  
ANTENA SEPARADAS DE VHF/UHF  
En algunas zonas será necesario utilizar una antena  
exterior.  
TELEVICION POR CABLE SIN CAJA  
DE CONVERTIDOR / DECODIFICADOR  
Utilice esta conexión si su sistema de televisión por  
cable se conecta directamente a su televisor/DVD sin  
una caja de convertidor. Utilice el mando a distancia  
del televisor/DVD para seleccionar los canales.  
monofónica (otra fuente) a la toma AUDIO L de  
este televisor/DVD. El audio saldrá igualmente por  
los canales izquierdo y derecho.  
Consulte la figura 5 de la página 11  
TELEVICION POR CABLE CON CAJA  
DE CONVERTIDOR/DECODIFICADOR  
O CAJA DE SATRLITE  
CONEXIÓN A UN  
AMPLIFICADOR EQUIPADO  
CON TOMAS DE ENTRADA  
DIGITAL, PLATINA MD O  
PLATINA DAT (Para DVD)  
Si su compañía de televisión por cable le suministra  
una caja de convertidor, o si usted utiliza un sistema  
de satélite, usted podrá utilizar la conexión básica  
mostrada aquí.  
La selección de los canales deberá hacerse con la caja  
de convertidor o con la caja de satélite. Esto significa  
que los canales no se podrán cambiar utilizando el  
mando a distancia del televisor/DVD.  
Utilice un cable digital coaxial de audio de venta en  
el comercio especializado para hacer las conexiones  
de audio.  
Consulte la figura 6 de la página 11  
NOTAS:  
PARA VER UN CANAL  
CODIFICADO/DECODIFICADO  
1) Ponga el selector de canales del televisor/DVD  
en la posición del canal de salida de la caja de  
convertidor de televisión por cable o de la caja de  
satélite. (Ej., CH3)  
La fuente de audio de un disco en un formato de  
sonido ambiental Dolby Digital de 5,1 canales no  
se puede grabar como sonido digital mediante una  
platina MD o DAT.  
2) Seleccione el canal que va a ver en su caja de  
convertidor de televisión por cable o caja de  
satélite.  
Asegúrese de desconectar la alimentación de todos  
los componentes antes de conectar otro  
componente.  
Consulte los manuales del propietario de los  
componentes que va a conectar al televisor/DVD.  
CONEXIÓN A TOMAS DE  
ENTRADA EXTERNA  
Cuando vea un programa grabado en otra fuente  
(videograbadora o videocámara), utilice las tomas de  
entrada de audio/vídeo de la parte delantera del  
televisor/DVD.  
Ponga DOLBY DIGITAL en OFF para la salida de  
audio en el modo de preparación. La reproducción  
en un televisor/DVD utilizando ajustes incorrectos  
puede causar distorsión de ruido, y también se  
pueden dañar los altavoces. (Consulte la página 28  
para poner DOLBY DIGITAL en OFF.)  
Conecte las tomas de salida de audio/vídeo de otra  
fuente a las tomas AUDIO L/R y VIDEO de este  
televisor/DVD. Luego pulse SELECT hasta que  
aparezca "AUX" en la pantalla.  
ES  
36  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONEXCIONA UN  
DECODIFICADOR DOLBY  
DIGITAL (Para DVD)  
TV SECTION  
PREPARACIÓN PARA LA  
UTILIZACIÓN  
Si utiliza este televisor/DVD para reproducir un disco  
DVD en un formato de sonido ambiental Dolby  
Digital de 5,1 canales, el televisor/DVD dará salida a  
un flujo de datos DOLBY DIGITAL desde su toma  
de salida de audio digital COAXIAL. Conectando el  
reproductor a un decodificador Dolby Digital, usted  
podrá disfrutar de un ambiente más convincente y  
real, con un sonido ambiental potente y de alta  
calidad similar al de los cines.  
SELECCIÓN DE IDIOMA  
TV  
1 Enchufe el cordón de alimentación  
del televisor/DVD  
Enchufe el cordón de alimentación del  
televisor/DVD en una toma de CA están-  
dar.  
Utilice cables digitales coaxiales de audio disponibles  
en el comercio especializado para hacer las  
conexiones de audio.  
NOTA:  
Si aparecen algunas cifras en la esquina de la pan-  
talla, pulse el botón POWER sin desenchufar el  
cordón de alimentación.  
Consulte la figura 7 de la página 12  
NOTAS:  
Asegúrese de desconectar la alimentación de todos  
los componentes del sistema antes de conector a  
otro componente.  
Asegúrese de que ...  
Pulse el botón POWER para encender el televi-  
sor/DVD.  
NOTA: Esta función afecta sólo el idioma en el menú  
de la pantalla y no la fuente de audio.  
Consulte los manuales del propietario de los  
componentes que vaya a conectar al televisor/DVD.  
Si conecta un decodificador Dolby Digital, ponga  
DOLBY DIGITAL en ON para la salida de audio  
en el modo de preparación. (Consulte la página 28  
para poner DOLBY DIGITAL en ON.)  
- TV SETUP -  
2 Seleccione “LANGUAGE”  
CHANNEL SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
A menos que se haga la conexión a un  
Pulse el botón SETUP en el mando  
B
decodificador Dolby Digital , ponga DOLBY  
DIGITAL en OFF para la salida de audio en el  
modo de preparación. La reproducción en el  
televisor/DVD utilizando ajustes incorrectos puede  
generar distorsión de ruido, y también puede  
estropear los altavoces.  
a distancia.  
Pulse el botón K o L para señalar  
“LANGUAGE”.  
3
Seleccione “ENGLISH”, “ESPAÑOL” o FRANÇAIS”  
Seleccione “ENGLISH”, “ESPAÑOL” o  
“FRANÇAIS” con el botón ENTER.  
4 Salga del modo de idioma  
Fabricado bajo licencia de Dolby  
Laboratories. “Dolby” y el símbolo de la D  
doble son marcas de fábrica de Dolby  
Laboratories.  
Pulse el botón SETUP en el mando a distancia para  
volver al modo del televisor.  
NOTA: Si, por alguna razón, el menú está en español  
o francés, pulse el botón SETUP en el mando a dis-  
tancia, pulse el botón K o L para señalar el  
“IDIOMA (ESPAÑOL)” o “LANGAGE  
(FRANÇAIS)”, a continuación, pulse el botón  
ENTER y pulse el botón SETUP en el mando a dis-  
tancia.  
ES  
37  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AJUSTE DE CANAL  
DVD SECTION  
TV  
REPRODUCCIÓN DE UN  
DVD DE VÍDEO O UN CD  
DE AUDIO  
Puede programar el sintonizador para buscar todos  
los canales que recibe en su localidad.  
NOTA: El canal preparado NO es necesario cuando  
esté conectado a una caja de cable o caja de satélite.  
Sólo tiene que seleccionar con el selector de canal del  
televisor/videograbadora al canal de salida de la caja  
de cabe o caja de satélite (por ejemplo el canal CH3).  
Seleccione el canal a ver en la caja de cable o caja de  
satélite.  
REPRODUCCION BASICA  
DVD-V  
CD  
MP3  
Para empezar  
¡Conecte el interruptor del amplificador y otros  
equipos, si fuera necesario.  
Asegúrese de que ...  
1 Pulse el boton POWER.  
¡La alimentación se conectará.  
Pulse el botón POWER para encender el televi-  
sor/DVD.  
1 Seleccione “AJUSTE DE CANAL”  
Pulse el botón SETUP en el mando  
a distancia.  
– M E N U –  
2 Pulse el botón OPEN/CLOSE.  
B
AJUSTE DE CANAL  
AJUSTE DE V-CHIP  
IDIOMA [ESPAÑOL]`  
TITULO [OFF]  
¡La bandeja de carga del disco se abrirá.  
Pulse el botón K o L para señalar  
“AJUSTE DE CANAL”.  
A continuación, pulse el botón  
ENTER.  
3 Ponga el dlsco en la bandeja con el lado  
de la eliguta hacia arriba.  
2 Empiece el prefijado automático  
Pulse el botón K o L para señalar  
“AUTOPROGRAMACION DE  
AJUSTE DE CANAL  
4 Pulse el botón PLAY.  
AGREGAR/BORRAR (CATV)  
B AUTOPROGRAMACION DE CA.  
CA”.  
¡La bandeja se cerrará automáticamente y la  
reproducción empezará luego desde el primer  
capítulo o pista del disco. Si la reproducción no  
empieza automáticamente, pulse PLAY.  
A continuación, pulse el botón  
ENTER.  
El sintonizador busca y memoriza  
todos los canales activos en su localidad.  
¡Cuando reproduzca un DVD que tenga grabado un  
menú de títulos, el menú aparecerá en la pantalla.  
3 Después de buscar  
El sintonizador se detiene en el canal memorizado  
más bajo.  
5
Pulse el botón STOP para detener la repro-  
ducción.  
Cuando se activa AUTOPROGRAMACION DE  
CA, donde no hay entrada de señal del televisor,  
aparecerá “NO HAY SEÑAL DE TV” en la pan-  
talla después de terminar la búsqueda de canales.  
El televisor/DVD puede reconocer los canales de  
TV para que sean canales de TV de antena de cable  
con las condiciones de recepción. En este caso,  
pruebe nuevamente con el prefijado automático en  
las condiciones de recepción fina.  
ES  
38  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MEMO  
ES  
39  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FUNAI CORPORATION  
LIMITED WARRANTY  
FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or workman-  
ship as follows:  
DURATION:  
PARTS:  
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from  
the date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded  
from this warranty.  
LABOR:  
FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date  
of original retail purchase.  
LIMITS AND EXCLUSIONS:  
THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE  
RECEIPT OR OTHER PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH  
THE PRODUCT TO OBTAIN SERVICE UNDER THIS WARRANTY  
This warranty shall not be extended to any other person or transferee.  
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing or  
if service was attempted by an unauthorized service center. This FUNAI CORPORATION Limited warranty does  
not apply to any product not purchased and used in the United States.  
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It  
does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not  
supplied by FUNAI CORP. or damage which results from accident, misuse, abuse, mishandling, misapplication,  
alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this prod-  
uct or damage which results from fire, flood, lightning or other acts of God.  
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE  
CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.  
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY  
GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE  
USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL  
OTHER WARRANTIES, EXPRESS OR IMPLIED AND OF ALL OTHER LIABILITIES ON THE PART OF  
FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY, AND FIT-  
NESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS REPRESENTA-  
TIVES IN THE UNITED STATES.  
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY A FUNAI AUTHORIZED  
SERVICE CENTER. THIS WARRANTY IS VALID WHEN THE UNIT IS CARRIED-IN TO FUNAI AUTHO-  
RIZED SERVICE FACILITY.  
IMPORTANT:  
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS  
THAT VARY FROM STATE TO STATE, IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE  
UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT  
FUNAI CORP.  
ATTENTION:  
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT  
WITHOUT PRIOR NOTICE.  
To locate your nearest FUNAI Authorized Service Center or for general service procedure,  
please call 1-800-242-7158 or write to the following:  
FUNAI CORPORATION, INC.  
SERVICE CENTER  
19900 Van Ness Avenue, Torrance, CA 90501  
Tel :1-800-242-7158  
Head Office: 100 North Street, Teterboro, NJ 07608  
PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.  
Printed in China  
1EMN20057  
T9002UC ★★★★★  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Sharp Microwave Oven R 1600 User Manual
Sharp Stereo System XL HP707 User Manual
Sony DVR DCR IP5 IP7BT User Manual
Sony Projector VPL PX32 User Manual
Sony VCR TRV828 User Manual
Spin Master Video Gaming Accessories Wiggly Wiggly Dance Mat User Manual
Stamina Products Rowing Machine 35 1399 User Manual
Stovax Stove Coal Effect Stove Range Conventional Flue User Manual
Subaru Robin Power Products Automobile Parts EH722 LP User Manual
Symphonic CRT Television CWF2703 User Manual