Sylvania TV VCR Combo 6719DF User Manual

OWNER’S  
MANUAL  
COLOR TV/VCR/DVD TRIPLE COMBO  
(19 inch)  
6719DF  
INSTRUCCIONES EN ESPAÑOL INCLUIDAS  
If you need additional operating assistance after reading this owner’s  
manual or to order replacement accessories, please call  
TOLL FREE : 1-800-968-3429.  
Please read before using this equipment  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FIGURE A  
EXAMPLE OF ANTENNA GROUNDING AS PER  
NATIONAL ELECTRICAL CODE  
ANTENNA  
LEAD I N  
WI RE  
GROUND  
CL AMP  
ANTENNA  
DISCHARGE UNIT  
(NEC SECTION 810-20)  
ELECTRI C  
SERVICE  
EQUIPMENT  
GROUNDING CONDUCTORS  
(NEC SECTION 810-21)  
GROUND CLAMPS  
NEC  
-
NATIONAL ELECTRICAL CODE  
POWER SERVICE GROUNDING  
ELECTRODE SYSTEM  
(NEC ART 250, PART H)  
S2898A  
13.Outdoor Antenna grounding - If an outside antenna or  
cable system is connected to the unit, be sure the antenna  
or cable system is grounded so as to provide some protec-  
tion against voltage surges and built-up static charges.  
Article 810 of the National Electrical Code, ANSI/NFPA  
No. 70, provides information with respect to proper  
grounding of the mast and supporting structure, grounding  
of the lead-in wire to an antenna discharge unit, size of  
grounding conductors, location of antenna-discharge unit,  
connection to grounding electrodes, and requirements for  
the grounding electrode. (Fig. A)  
19.Damage Requiring Service - Unplug this unit from the  
wall outlet and refer servicing to qualified service personnel  
under the following conditions:  
a. When the power-supply cord or plug is damaged or frayed.  
b. If liquid has been spilled, or objects have fallen into the unit.  
c. If the unit has been exposed to rain or water.  
d. If the unit does not operate normally by following the oper-  
ating instructions. Adjust only those controls that are cov-  
ered by the operating instructions, as improper adjustment  
of other controls may result in damage and will often  
require extensive work by a qualified technician to restore  
the unit to its normal operation.  
14.Lightning - For added protection for this unit receiver during  
a lightning storm, or when it is left unattended and unused for  
long periods of time, unplug it from the wall outlet and dis-  
connect the antenna or cable system. This will prevent dam-  
age to the unit due to lightning and power-line surges.  
e. If the unit has been dropped or damaged in any way.  
f. When the unit exhibits a distinct change in performance,  
this indicates a need for service.  
15.Power Lines - An outside antenna system should not be  
located in the vicinity of overhead power lines or other  
electric light or power circuits, or where it can fall into  
such power lines or circuits. When installing an outside  
antenna system, extreme care should be taken to keep from  
touching such power lines or circuits as contact with them  
might be fatal.  
20.Replacement Parts - When replacement parts are required,  
be sure the service technician has used replacement parts  
specified by the manufacturer that have the same characteris-  
tics as the original part. Unauthorized substitutions may result  
in fire, electric shock, injury to persons or other hazards.  
21.Safety Check - Upon completion of any service or repairs  
to this unit, ask the service technician to perform routine  
safety checks to determine that the unit is in proper operat-  
ing condition.  
16.Overloading - Do not overload wall outlets and extension  
cords as this can result in a risk of fire or electric shock.  
17.Object and Liquid Entry - Never push objects of any  
kind into this unit through openings as they may touch dan-  
gerous voltage points or short out parts that could result in  
a fire or electric shock. Never spill liquid of any kind on  
the unit.  
22.Heat - This unit product should be situated away from heat  
sources such as radiators, heat registers, stoves, or other  
products (including amplifiers) that produce heat.  
18.Servicing - Do not attempt to service this unit yourself as  
opening or removing covers may expose you to dangerous  
voltage or other hazards. Refer all servicing to qualified  
service personnel.  
- 3 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PRECAUTIONS  
LASER SAFETY  
IMPORTANT COPYRIGHT INFORMATION  
Unauthorized copying, broadcasting, public perfor-  
mance and lending of discs are prohibited.  
This product incorporates copyright protection tech-  
nology that is protected by U.S. patents and other  
intellectual property rights. Use of this copyright  
protection technology must be authorized by  
Macrovision, and is intended for home and other  
limited viewing uses only unless otherwise autho-  
rized by Macrovision. Reverse engineering or dis-  
assembly is prohibited.  
This unit employs a laser. Only a qualified service  
person should remove the cover or attempt to ser-  
vice this device, due to possible eye injury.  
CAUTION: USE OF CONTROLS OR ADJUST-  
MENTS OR PERFORMANCE OF PROCE-  
DURES OTHER THAN THOSE SPECIFIED  
HEREIN MAY RESULT IN HAZARDOUS  
RADIATION EXPOSURE.  
FCC WARNING- This equipment may gener-  
ate or use radio frequency energy. Changes or  
modifications to this equipment may cause  
harmful interference unless the modifications  
are expressly approved in the instruction man-  
ual. The user could lose the authority to oper-  
ate this equipment if an unauthorized change  
or modification is made.  
CAUTION: VISIBLE AND INVISIBLE LASER  
RADIATION WHEN OPEN AND INTERLOCK  
DEFEATED. DO NOT STARE INTO BEAM.  
LOCATION: INSIDE, NEAR THE DECK  
MECHANISM.  
RADIO-TV INTERFERENCE  
This Class B digital apparatus complies with  
Canadian ICES-003.  
This equipment has been tested and found to com-  
ply with the limits for a Class B digital device, pur-  
suant to Part 15 of the FCC Rules. These limits are  
designed to provide reasonable protection against  
harmful interference in a residential installation.  
This equipment generates, uses, and can radiate  
radio frequency energy and, if not installed and  
used in accordance with the instructions, may cause  
harmful interference to radio communications.  
However, there is no guarantee that interference  
will not occur in a particular installation. If this  
equipment does cause harmful interference to  
radio or television reception, which can be deter-  
mined by turning the equipment off and on, the  
user is encouraged to try to correct the interfer-  
ence by one or more of the following measures:  
1) Reorient or relocate the receiving antenna.  
2) Increase the separation between the equipment  
and receiver.  
Cet appareil numérique de la classe B est  
conforme à la norme NMB-003 du Canada.  
CAUTION: TO PREVENT ELECTRIC SHOCK,  
MATCH WIDE BLADE OF PLUG TO WIDE  
SLOT, FULLY INSERT.  
ATTENTION: POUR ÉVITER LES CHOC  
ÉLECTRIQUES, INTRODUIRE LA LAME LA  
PLUS LARGE DE LA FICHE DANS LA  
BORNE CORRESPONDANTE DE LA PRISE  
ET POUSSER JUSQU’AU FOND.  
A NOTE ABOUT RECYCLING  
Batteries should never be thrown away or inciner-  
ated but disposed of in accordance with your local  
regulations concerning chemical wastes.  
3) Connect the equipment into an outlet on a cir-  
cuit different from that to which the receiver is  
connected.  
4) Consult the dealer or an experienced radio/TV  
technician for help.  
The serial number of this product may be found on the back of the unit. No other unit has the same serial  
number as yours. You should record the number and other vital information here and retain this book as a per-  
manent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.  
Date of Purchase  
Dealer Purchase from  
Dealer Address  
Dealer Phone No.  
Model No.  
Serial No.  
- 4 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING  
LOCATION  
Moisture condensation may occur inside the unit  
when it is moved from a cold place to a warm place  
or after heating a cold room or under conditions of  
high humidity. If a DVD is played in a unit which has  
moisture, it may damage the DVD and the unit.  
Therefore when the condensation occurs inside the  
unit, turn the unit on and allow at least 2 hours for the  
unit to dry out.  
For safe operation and satisfactory performance of  
your unit, keep the following in mind when selecting  
a place for its installation:  
Shield it from direct sunlight and keep it away from  
sources of intense heat.  
Avoid dusty or humid places.  
Avoid places with insufficient ventilation for proper  
heat dissipation. Do not block the ventilation holes at  
the top or bottom of the unit. Do not place the unit  
on a carpet because this will block the ventilation  
holes.  
SYMBOLS USED IN THIS MANUAL  
The following symbols below appear in some head-  
ings and notes in this manual, with the following  
meanings.  
Install unit in a horizontal position.  
Avoid locations subject to strong vibration.  
Do not place the unit near strong magnetic fields.  
Avoid moving the unit to locations where tempera-  
ture differences are extreme.  
Be sure to remove disc and unplug the AC power  
cord from the outlet before carrying the unit.  
TV/VCR  
: Description refers to TV/VCR operation (in the  
TV/VCR mode).  
DVD-V  
: Description refers to playback of DVD video discs  
(in the DVD mode).  
AVOID THE HAZARDS OF  
CD  
ELECTRICAL SHOCK AND FIRE  
: Description refers to playback of Audio CDs  
(in the DVD mode).  
Do not handle the power cord with wet hands.  
Do not pull on the power cord when disconnecting  
it from an AC wall outlet. Grasp it by the plug.  
If by accident, water is spilled on your unit, unplug  
the power cord immediately and take the unit to our  
Authorized Service Center for servicing.  
QUICK  
: Description refers to the items to be set by the  
QUICK mode (in the DVD mode).  
Do not put your fingers or objects into the unit disc  
loading tray.  
Do not place anything directly on top of the unit.  
SUPPLIED ACCESSORIES  
Remote Control Unit  
Batteries  
Owner’s Manual  
Owner's Manual  
NE209UD  
2 AA Batteries  
1EMN20670  
If you need to replace these accessories, please refer to the PART NO. under the illustrations and call our  
help line mentioned on the front page.  
Depending on your antenna system, you may need different types of Combiners (Mixer) or Separators  
(Splitter). Contact your local electronics store for these items.  
- 5 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
C IMPORTANT SAFEGUARDS . . . . .2  
C SPECIAL PLAYBACK . . . . . . . . . .24  
RENTAL PLAYBACK . . . . . . . . . .24  
AUTO REPEAT PLAYBACK . . . . .24  
C SEARCH FUNCTION . . . . . . . . . . .37  
TRACK SEARCH . . . . . . . . . . . . .37  
TITLE / CHAPTER SEARCH . . . .37  
TIME SEARCH . . . . . . . . . . . . . . .37  
MARKER SETUP SCREEN . . . . . .37  
C PRECAUTIONS . . . . . . . . . . . . . . . .4  
LOCATION . . . . . . . . . . . . . . . . . . .5  
AVOID THE HAZARDS OF  
ELECTRICAL SHOCK AND FIRE .5  
C SEARCH . . . . . . . . . . . . . . . . . . . . .25  
ZERO RETURN . . . . . . . . . . . . . . .25  
WARNING . . . . . . . . . . . . . . . . . . . .5  
PICTURE SEARCH . . . . . . . . . . . .25  
TIME SEARCH . . . . . . . . . . . . . . .25  
INDEX SEARCH . . . . . . . . . . . . . .26  
C
SPECIAL PLAYBACK FUNCTION . . .38  
REPEAT . . . . . . . . . . . . . . . . . . . . .38  
PROGRAM . . . . . . . . . . . . . . . . . . .38  
RANDOM PLAYBACK . . . . . . . . .38  
SYMBOLS USED IN THIS  
MANUAL . . . . . . . . . . . . . . . . . . . . .5  
C SUPPLIED ACCESSORIES . . . . . . .5  
C TABLE OF CONTENTS . . . . . . . . . .6  
C FEATURES . . . . . . . . . . . . . . . . . . . .7  
C SPECIAL FEATURES . . . . . . . . . .27  
REAL TIME TAPE COUNTER . . .27  
AUTO REWIND-EJECT . . . . . . . .27  
C CHANGING THE SETTINGS . . . .39  
SUBTITLE LANGUAGE . . . . . . . .39  
AUDIO LANGUAGE . . . . . . . . . . .39  
STEREO SOUND MODE . . . . . . . .39  
CAMERA ANGLE . . . . . . . . . . . . .40  
BLACK LEVEL SETTING . . . . . . .40  
VIRTUAL SURROUND . . . . . . . . .40  
C RECORDING . . . . . . . . . . . . . . . . .28  
C OPERATING CONTROLS AND  
FUNCTIONS . . . . . . . . . . . . . . . . . . .9  
NORMAL RECORDING . . . . . . . .28  
INSTALLING THE BATTERIES . .11  
SKIPPING UNWANTED SCENES  
DURING RECORDING . . . . . . . . .28  
C PREPARATION FOR USE . . . . . . .12  
OTR (One Touch Recording) . . . . . .29  
ANTENNA/CABLE  
CONNECTION . . . . . . . . . . . . . . . .12  
COPYING A VIDEO CASSETTE  
(Requires a VCR or camcorder) . . .29  
C
THE ON-SCREEN INFORMATION . .41  
CONNECTING TO FRONT A/V  
INPUT JACKS . . . . . . . . . . . . . . . .13  
C CHANGING THE DVD SET UP  
C TIMER RECORDING . . . . . . . . . . .30  
ITEMS . . . . . . . . . . . . . . . . . . . . . . .42  
CONNECTING TO A STEREO  
AMPLIFIER EQUIPPED WITH DIGI-  
TAL INPUT JACKS (for DVD) . . .13  
AUTOMATIC  
TIMER RECORDING . . . . . . . . . .30  
CUSTOM MENU . . . . . . . . . . . . . .42  
LANGUAGE SETTING . . . . . . .42  
DISPLAY SETTING . . . . . . . . . .43  
AUDIO SETTING . . . . . . . . . . .43  
PARENTAL CONTROL . . . . . . .44  
OTHER SETTINGS . . . . . . . . . .44  
INITIALIZE . . . . . . . . . . . . . . . . . .44  
AUTO RETURN . . . . . . . . . . . . . . .32  
CONNECTING TO A DOLBY  
DIGITAL DECODER (for DVD) . .14  
C ON SCREEN DISPLAY . . . . . . . . .33  
C CABLE CHANNEL  
DESIGNATIONS . . . . . . . . . . . . . .33  
TV/VCR SECTION  
C TV OPERATION AND SETTINGS .15  
WATCHING A TV PROGRAM . . .15  
DEGAUSSING . . . . . . . . . . . . . . . .15  
PICTURE CONTROL . . . . . . . . . . .15  
SLEEP TIMER . . . . . . . . . . . . . . . .16  
CLOSED CAPTION SYSTEM . . . .16  
CHANNEL SET UP . . . . . . . . . . . .17  
DVD SECTION  
C TROUBLESHOOTING GUIDE . . .45  
C ABOUT THE DISCS . . . . . . . . . . . .34  
PLAYABLE DISCS . . . . . . . . . . . .34  
UNPLAYABLE DISCS . . . . . . . . . .34  
C MAINTENANCE . . . . . . . . . . . . . . .48  
DISC HANDLING . . . . . . . . . . . . .48  
C SPECIFICATIONS . . . . . . . . . . . . .49  
C ESPAÑOL . . . . . . . . . . . . . . . . . . . .50  
C WARRANTY . . . . . . . . . . .Back Cover  
C PLAYING A DISC . . . . . . . . . . . . . .35  
BASIC PLAYBACK . . . . . . . . . . . .35  
GENERAL FEATURES . . . . . . . . .35  
DISC MENU . . . . . . . . . . . . . . . . .35  
TITLE MENU . . . . . . . . . . . . . . . . .35  
RESUME . . . . . . . . . . . . . . . . . . . .36  
PAUSE . . . . . . . . . . . . . . . . . . . . . .36  
STEP BY STEP PLAYBACK . . . . .36  
CLOCK SET UP  
(AUTO / MANUAL) . . . . . . . . . . . .18  
DAYLIGHT-SAVING TIME . . . . . .19  
V-CHIP SET UP . . . . . . . . . . . . . . .20  
TV RATING SET UP . . . . . . . . .20  
MPAA RATING SET UP . . . . . .21  
CHANGE ACCESS CODE . . . . .21  
MENU LANGUAGE . . . . . . . . . . .21  
FAST FORWARD /  
FAST REVERSE . . . . . . . . . . . . . .36  
SLOW FORWARD /  
C VIDEO CASSETTE . . . . . . . . . . . . .22  
SLOW REVERSE . . . . . . . . . . . . . .36  
C PLAYBACK . . . . . . . . . . . . . . . . . . .23  
NORMAL PLAYBACK . . . . . . . . .23  
TRACKING ADJUSTMENT . . . . .23  
SLOW MOTION . . . . . . . . . . . . . .23  
STILL PICTURE . . . . . . . . . . . . . .23  
VERTICAL HOLD CONTROL . . .23  
ZOOM . . . . . . . . . . . . . . . . . . . . . .36  
- 6 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FEATURES  
TV/VCR Mode  
¡Rotary 4-head Record/Playback System  
¡Three different playback tape speeds : SP/LP/SLP  
Four heads ensure excellent picture quality and  
special effects playback.  
¡Two different recording tape speeds : SP/SLP  
¡Auto Head Cleaner  
Automatically cleans video heads as you insert or  
remove a cassette.  
¡Index Search  
Fast-forwards to start of next recording.  
¡Slow Motion  
¡Zero Return  
View recorded program at slower than normal  
speed.  
The tape returns to counter of 0:00:00 by rewinding  
or fast forwarding.  
¡Infrared remote control  
¡Still  
“Freeze” the picture at any time, for close viewing  
of a particular scene.  
¡Trilingual on screen TV/VCR setup display selec-  
table in English, Spanish or French  
¡Real time counter  
¡Digital Auto Tracking (DTR)  
Automatically adjusts the tracking for each tape  
you play.  
This shows the elapsed recording or playback time  
in hours, minutes and seconds. The “–” indication  
will appear when the tape is rewound further than  
the tape counter position “0:00:00”.  
¡Rental play mode  
Improves playback picture quality from worn tapes,  
such as rental tapes.  
¡181 channel capability PLL frequency synthesiz-  
er tuner with direct station call  
(A converter may be necessary to view scrambled  
cable channels.)  
¡Auto repeat  
Allows you to repeat the playing of a tape indefi-  
nitely without pressing [PLAY O].  
¡Auto Clock Setting  
Allows you to set the clock function from a PBS  
broadcast station.  
¡Time search  
Lets you set the unit to advance the tape by entering  
the desired playback time you want to skip.  
¡Closed Caption Decoder  
¡OTR (One Touch Recording)  
Instant timed recording from 30 to 480 minutes is  
possible by pressing [I REC/OTR].  
You may view specially labeled (cc) TV programs,  
movies, news, prerecorded tapes, etc. with either a  
dialogue caption or text display added to the pro-  
gram.  
¡1 Year, 8 events (including Daily and Weekly)  
Timer Recording  
¡Auto power on and off system  
The built-in timer allows you to record up to 8 pro-  
grams at different times on different channels up to  
1 year in advance. The Daily timer allows record-  
ings to be made of daily broadcasts and the Weekly  
timer allows recording to be made once a week up  
to the end of the tape.  
Automatically turns on the unit when you insert the  
cassette, turns off after auto-rewind and ejects  
when the beginning of the tape is reached.  
¡Auto rewind when the end of a tape is reached  
(This function doesn’t occur when using timer  
recording.)  
¡Auto return  
After timer recording is finished, the unit can  
return to the beginning of the recording.  
¡Smooth mode change  
TV/VCR mode and DVD mode automatically  
changes without control.  
¡Sleep timer  
Allows you to have the unit automatically turn off  
at a desired time.  
¡2 step picture search operation  
You can view a video program at a high speed or  
super high speed in either a forward or reverse  
direction in LP and SLP mode. For SP mode, only  
high speed is available.  
¡Timer Program Extension  
Allows you to shift the time schedule for automatic  
timer recording.  
¡V-CHIP  
Enables parents to prevent their children from  
watching inappropriate material on TV.  
- 7 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DVD Mode  
¡Dolby Digital sound  
¡On-screen display  
This unit can handle Dolby Digital surround sound  
having 5.1 channels when connected to a Dolby  
Digital decoder.  
Information about the current operation can be dis-  
played on a TV screen, allowing you to confirm the  
currently active functions (such as program play-  
back), on the TV screen using the remote control.  
¡Still/fast/slow/step playback  
¡Search  
Various playback modes are available including still  
pictures, fast forward/reverse, slow motion and step  
frames.  
Chapter search / Title search / Track search / Time  
search  
¡Repeat  
Chapter / Title / Track / All / A-B  
¡Random playback for Audio CD  
This unit can shuffle the order of tracks to play them  
in random order.  
¡Zoom  
Magnified screen can be displayed.  
¡Program playback for Audio CD  
You can program the order of tracks to play them in  
any desired order.  
¡Marker  
The part designated by user can be called back.  
¡DVD menus in a desired language  
You can display DVD menus in a desired language,  
if available on a DVD.  
¡Resume Play  
User can resume to playback from the part at which  
the play was stopped.  
¡Screen saver/Auto power-off functions  
¡Virtual Surround  
The screen saver program starts when there is no  
input from the unit for 5 minutes in the stop mode.  
After the screen saver program is activated for 15  
minutes, the power automatically turns off.  
¡Bit rate indication  
¡DRC (Dynamic range control)  
You can control the range of sound volume.  
¡Subtitles in a desired language  
You can select a desired language for the display  
subtitles, if that language is available on a disc.  
¡Selecting a camera angle  
You can select the desired camera angle, if a disc  
contains sequences recorded from different angles.  
¡Choices for audio language and sound mode  
You can select the desired audio language and sound  
mode, if different languages and modes are available  
on a disc.  
¡Parental lock  
You can set the control level to limit playback of  
discs which may not be suitable for children.  
¡Automatic detection of discs  
This unit automatically detects if the loaded disc is  
DVD or Audio CD.  
- 8 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATING CONTROLS AND FUNCTIONS  
- FRONT PANEL - [Fig.1]  
DVD buttons  
TV/VCR buttons  
1
2
3 4  
3
5
6
7 8 9 10 11 12 13 14 4 15 16 17 18 19 20 21  
5.C STOP Button [TV/VCR P.23 / DVD P.35]  
(Front panel) Stops operation of the disc.  
(Remote control) Stops operation of the disc or  
tape contents.  
[Fig. 2]  
- REMOTE CONTROL -  
6.A OPEN/CLOSE Button [DVD P.35]  
Press to insert a disc into or remove it from the  
tray.  
7.Disc loading tray  
8.DVD Indicator  
Lights up during DVD mode.  
POWER PICTURE SLEEP SELECT  
1
9
44  
22  
1
4
2
5
8
0
3
6
CH.  
11  
23  
7
PAUSE  
9
+100  
VOL.  
2
9.SELECT Button [TV/VCR P.15] [DVD P.35]  
+10  
24  
25  
26  
Press to change to TV/VCR mode, external input  
mode or DVD mode. You can see the mode  
(TV/VCR or DVD) on the front panel indicator.  
SPEED C.RESET  
ZOOM  
MUTE  
43  
42  
PLAY  
STOP  
3 (DVD)  
(DVD) 3  
(TV/VCR) 414  
10.TV/VCR Indicator  
15 (TV/VCR)  
Lights up during TV/VCR mode.  
DISC  
MENU  
5
41  
40  
39  
38  
RECORD  
K
L
11. CHANNEL (CH.)  
/
Buttons  
13  
Press to select memorized channels.  
DISPLAY  
SETUP  
ENTER  
27  
12. Recording Indicator  
TITLE  
RETURN  
Flashes during recording. Lights up in the Stand-  
by mode for Timer Recording.  
28  
29  
30  
CLEAR SEARCH MODE REPEAT  
A-B  
37  
13. I REC/OTR Button (Front Panel) [TV/VCR P.29]  
Press to start manual recording. Press repeatedly  
to start One Touch Recording.  
AUDIO SUBTITLE ANGLE  
MODE  
31  
32  
33  
36  
35  
34  
RECORD Button (Remote Control) [TV/VCR P.28]  
Press to start manual recording.  
14. E REW Button (for TV/VCR) [TV/VCR P.25]  
Press to rewind the tape or to view the picture  
rapidly in reverse during playback mode. (Rewind  
Search)  
15. F.FWD D Button (for TV/VCR) [TV/VCR P.25]  
Press to rapidly advance the tape or to view the  
picture rapidly in forward during playback mode.  
(Forward Search)  
1.POWER Button [TV/VCR P.15 / DVD P.35]  
Press to turn the power on and off.  
K
L
2.VOLUME (VOL.)  
/
Buttons  
Press to control the volume level for the DVD and TV.  
3.SKIP H / G Buttons (for DVD) [DVD P.37]  
Press once to skip chapters or tracks to a desired  
point.  
SEARCH E / D Buttons (for DVD) [DVD P.36]  
Press and hold to change forward or reverse play-  
back speed.  
16.  
C
A STOP/EJECT Button [TV/VCR P.22, 25]  
Press to stop the tape motion. Press in the stop  
mode to remove tape from the unit.  
17. Remote sensor window  
18. HEADPHONE Jack  
To connect headphone (not supplied) for personal  
listening.  
4.B PLAY Button [TV/VCR P.23 / DVD P.35]  
Starts playback of the disc or tape contents.  
- 9 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
- REAR PANEL - [Fig.3]  
AUDIO OUT  
COAXIAL  
ANT.  
45  
46  
47  
19. VIDEO input Jack  
30. CLEAR Button [DVD P.37]  
Connect to the video output jack of a video camera  
or VCR.  
Press to clear or cancel a setting currently entered.  
31. MODE Button [DVD P.38]  
20. AUDIO L/R input Jacks  
Connect to the audio output jacks of a video cam-  
era or VCR.  
Press to call up the program screen or the random  
screen in the stop mode.  
Press to call up the Black Level Setting screen or  
the Virtual Surround screen during playback.  
21. Cassette compartment  
32. SEARCH MODE Button [DVD P.37]  
22. PICTURE Button  
Press to locate a desired point.  
Press to adjust the picture.  
33. AUDIO Button [DVD P.39]  
Press to select a desired audio language or sound  
mode.  
23. Number Buttons  
TV/VCR Mode: [P.17]  
Press two digits to directly access the desired  
channel.  
Remember to press [0] before a single digit channel.  
+100 Button–  
Press to select cable channels which are higher  
than 99.  
34. SUBTITLE Button [DVD P.39]  
Press to select a desired subtitle language.  
35. REPEAT Button [DVD P.38]  
Repeats playback of the current disc, title, chapter,  
or track.  
DVD Mode: [P.37]  
Press to enter the desired number.  
+10 Button–  
Press to enter the desired numbers which are higher  
than 9.  
36. ANGLE Button [DVD P.40]  
Press to change the camera angle to see the  
sequence being played back from a different angle  
(if available).  
37. A-B Button [DVD P.38]  
24. PAUSE F Button [TV/VCR P.23 / DVD P.36]  
Repeats playback of a selected section.  
Pauses the current disc or tape operation.  
38. RETURN Button [TV/VCR P.31] [DVD P.37]  
25. SPEED Button [TV/VCR P.28]  
Press to choose the desired recording speed:  
SP/SLP.  
Returns to the previous screen in the setup menu.  
39. ENTER Button [TV/VCR P.16] [DVD P.35]  
Press to accept a setting.  
26. C.RESET Button [TV/VCR P.25]  
Press to reset counter to “0:00:00”.  
Press to cancel a setting of timer program.  
(Refer to page 31.)  
K
L
{
B
40.  
/
/
/
Buttons  
TV/VCR Mode: [P.15]  
Press to select a setting mode from the menu on  
the TV screen.  
Press to select or adjust from a particular menu.  
DVD Mode: [P.35]  
27. DISPLAY Button  
TV/VCR Mode: [P.33]  
Displays the counter or the current channel num-  
ber and current time on the TV screen.  
DVD Mode: [P.41]  
Press to select a menu item.  
41. DISC MENU Button [DVD P.35]  
Calls up the DVD menu.  
Displays the current status on the TV screen.  
42. ZOOM Button [DVD P.36]  
28. SETUP Button [TV/VCR P.16] [DVD P.42-44]  
Press to enter or exit the setup menu of TV or  
DVD.  
Enlarges part of a DVD-reproduced image.  
43. MUTE Button [TV/VCR P.15]  
Mutes the sound. Press it again to restore sound.  
29. TITLE Button [DVD P.35]  
44. SLEEP Button [TV/VCR P.16]  
Displays the title menu.  
Sets the Sleep Timer.  
- 10 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
45. ANT(ENNA). Jack [P.12]  
Connect to an antenna, cable system or satellite  
system.  
47. AUDIO OUT COAXIAL Jack [P.13]  
Connect to the digital input of an external  
amplifier or decoder (for DVD Audio only).  
46. Power cord [P.15]  
Connect to a standard AC outlet (120V/60Hz).  
NOTE:  
Remove the power cord from the hook to  
avoid breaking a wire before you connect to a  
standard AC outlet.  
NOTE:  
We do not recommend the use of universal remote controls. Not all of the functions may be controlled with  
a universal remote control.  
If you decide to use a universal remote control with this unit, please be aware that the code number given  
may not operate this unit. In this case, please call the manufacturer of the universal remote control.  
INSTALLING THE BATTERIES  
1)Open the battery compartment cover by pressing  
the cover on the remote unit in the direction of the  
arrow.  
2)Insert 2 “AA” penlight batteries into the battery  
compartment in the direction indicated by the  
polarity (+/-) markings.  
[BATTERY PRECAUTIONS]  
Be sure to follow the correct polarity as indicated  
in the battery compartment. Reversed batteries  
may cause damage to the device.  
Do not mix different types of batteries together  
(e.g. Alkaline and Carbon-Zinc) or old batteries  
with fresh ones.  
3)Replace the cover.  
If the device is not to be used for a long period of  
time, remove the batteries to prevent damage or  
injury from possible battery leakage.  
Do not try to recharge batteries not intended to be  
recharged; they can overheat and rupture.  
- 11 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREPARATION FOR USE  
ANTENNA/CABLE CONNECTION  
Plug the incoming cable into the ANT. jack on the rear of the unit.  
If your cable service supplies you with a converter box or if you use a  
satellite system, connect the box with this unit as shown below.  
Cable  
TV signal  
Antenna  
or  
Incoming cable from home Antenna /  
Cable Company (No Cable Box)  
AUDIO OUT  
COAXIAL  
ANT.  
Rear of the unit  
ANT.  
Cable Box or  
Satellite Box*  
OR  
OUT  
IN  
[Fig. 4]  
Incoming cable from Cable Company  
or Satellite Antenna  
*NOTE (DO NOT DISCONNECT FROM BOX)  
Some cable TV systems use scrambled signals and  
require a special converter to receive these channels.  
Consult your local cable company.  
Note to CATV system installer:  
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides  
guidelines for proper grounding and in particular, specifies that the cable ground shall be connected to the grounding  
system of the building as close to the point of cable entry as practical.  
Bent pin  
NOTE:  
Before plugging the antenna into the ANT. jack of the unit, check that the pin is  
not bent. If it is bent, straighten the pin as illustrated, then plug the pin into the  
ANT. jack of the unit.  
Cable  
Plug  
(Needs to be  
straightened)  
(Straight pin)  
NOTE:  
For your safety and to avoid damages to the unit, unplug the antenna cable from the ANT. jack  
before moving the unit.  
- 12 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTING TO FRONT A/V INPUT JACKS  
When you watch a program recorded on another source (VCR or video camera), use the  
Audio/Video input jacks on the front of the unit.  
AUX  
Connect the Audio/Video output jacks of another source to the AUDIO L/R and VIDEO  
jacks of this unit.  
K
L
Then press [SELECT] or [CH.  
/
] until “AUX” appears on the screen.  
DVD buttons  
TV/VCR buttons  
ex.  
VCR or video camera, etc.  
To the Audio output jacks  
(IN)  
Audio cable  
(commercially available)  
HEADPHONE VIDEO  
L
AUDIO  
R
(OUT)  
(OUT)  
To the Video output jack  
[Front of the unit]  
Video cable  
(commercially available)  
(IN)  
[Fig. 5]  
NOTE:  
When you connect a monaural VCR (another source) to this unit, connect the Audio output jack of the  
monaural VCR (another source) to the AUDIO L jack of this unit. The audio will output in both L and R  
channel equally.  
CONNECTING TO A STEREO AMPLIFIER EQUIPPED WITH  
DIGITAL INPUT JACKS (for DVD)  
Use an audio coaxial digital cable (commercially available) for the audio connections.  
Connect to an amplifier equipped with digital input jacks such as MD Deck or DAT Deck.  
AUDIO OUT  
COAXIAL  
A
A
NNTT..  
(OUT)  
ex.  
MD deck, DAT deck, etc.  
To AUDIO OUT  
COAXIAL jack  
(Only DVD AUDIO OUT)  
To Coaxial digital  
Audio input jack  
Audio coaxial digital cable  
(commercially available)  
(IN)  
[Fig. 6]  
NOTES:  
The audio source on a disc in a 5.1 channel Dolby Digital surround format cannot be recorded as digital  
sound by an MD or DAT deck.  
Be sure to turn off the power to all components in the system before connecting another component.  
Refer to the Owner’s Manuals for the components to be connected to the unit.  
Set “DOLBY DIGITAL” to “PCM” for audio output in the setup mode. Playing a unit using incorrect set-  
tings may generate noise distortion and may also damage the speakers. (Refer to page 43.)  
- 13 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTING TO A DOLBY DIGITAL DECODER (for DVD)  
If using this unit to play a DVD disc in a 5.1 channel Dolby Digital surround format, the unit outputs a  
DOLBY DIGITAL Data stream from its AUDIO OUT COAXIAL jack. By hooking the unit up to a Dolby  
Digital decoder, you can enjoy a more convincing, realistic ambience with powerful and high-quality surround  
sound as enjoyed in movie theaters.  
Use audio coaxial digital cables (commercially available) for the audio connections.  
Center  
speaker  
AUDIO OUT  
COAXIAL  
ANT.  
(OUT)  
Front speaker  
(left)  
Front speaker  
(right)  
To AUDIO OUT  
COAXIAL jack  
(Only DVD AUDIO OUT)  
Dolby Digital  
decoder  
To Coaxial digital  
Audio input jack  
(IN)  
Audio coaxial digital cable  
(commercially available)  
Subwoofer  
Surround  
speaker  
(left)  
Surround  
speaker  
(right)  
[Fig. 7]  
NOTES:  
Be sure to turn off the power to all components in the system before connecting another component.  
Refer to the Owner’s Manuals for the components to be connected to the unit.  
If connected to a Dolby Digital decoder, set “DOLBY DIGITAL” to “BITSTREAM” for audio output in the  
setup mode. (Refer to page 43.)  
Unless connected to a Dolby Digital decoder, set “DOLBY DIGITAL” to “PCM” for audio output in the  
setup mode. Playing a unit using incorrect settings may generate noise distortion and may also damage the  
speakers. (Refer to page 43.)  
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are  
trademarks of Dolby Laboratories.  
- 14 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TV/VCR SECTION  
TV OPERATION AND SETTINGS  
WATCHING A TV PROGRAM  
DEGAUSSING  
TV/VCR  
This television has a degaussing circuit that will clear  
up color errors on the TV screen that are caused by  
any excess magnetism which happens to get too close  
to the TV. This circuit is designed to operate once  
when the set is first plugged in. If minor color  
errors are seen in some locations on the screen,  
please unplug the TV for approximately 30 min-  
utes. When the TV is plugged back in, the degauss-  
ing circuit will operate once to clear them up. Repeat  
this procedure any time the TV screen is accidentally  
magnetized or when the TV is moved or relocated.  
TV/VCR  
1 Plug in the unit power cord  
Plug the unit power cord into a standard  
AC outlet.  
NOTE:  
If any digits appear in the corner of the  
screen, press [POWER] without  
unplugging the power cord.  
2 Turn on the unit  
Press [POWER] to turn on the unit.  
PICTURE CONTROL  
TV/VCR  
3 Select the channel number  
K
L
Press [CH.  
/
] or the Number buttons to select  
The unit’s picture controls – BRIGHT, CON-  
TRAST, COLOR, TINT and SHARPNESS – are  
preset to factory specifications. Although they are  
usually the best, you may need to make some further  
adjustments for a more natural looking image.  
your desired channel number.  
Notes for using the Number buttons:  
¡You must precede single-digit channel numbers  
with a zero (for example: 02, 03, 04 and so on).  
¡When selecting cable channels which are higher  
than 99, press [+100] first, then press the last two  
digits. (Example: to select channel 125, first press  
[+100] then press [2] and [5].)  
Make sure ...  
The unit must be turned on.  
1 Call up the menu  
4 Adjust sound  
Press [PICTURE].  
X
Y
Press [VOL.  
/
] to adjust the  
volume.  
2 Select item you want to adjust  
Press [K / L] until desired control is displayed.  
VOLUME 20  
Press [MUTE] to instantly mute  
the sound.  
Press it again to restore the previous sound level.  
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
BRIGHT  
CONTRAST  
COLOR  
TINT  
SHARPNESS  
NOTE:  
If you press [CH.  
can change the TV channels. Even if you turn off  
the unit in the DVD mode, when you turn it on  
again, it will go into the TV/VCR mode.  
BRIGHT  
K
L
/
] in the DVD mode, you  
P
P
P
P
P
P
P
C
P
P
P
P
P
P
P +  
3 Adjust the setting  
Press  
seconds.  
[
s
/
B]  
to adjust to your desired level within 5  
TO WATCH CABLE OR SATELLITE  
CHANNEL  
If the unit is connected to a cable box or satellite  
box, press [CH.  
according to the output channel setting of the  
device, and select desired channel on that device.  
s
to decrease  
brightness  
to decrease  
contrast  
B
BRIGHT  
to increase  
brightness  
to increase  
contrast  
K
L
/
] to select CH3 or CH4  
CONTRAST  
COLOR  
TINT  
SHARPNESS to soft  
to pale  
to brilliant  
TO WATCH EXTERNAL INPUT  
to purple  
to green  
to clear  
When an external equipment is connected to the  
front AUDIO/VIDEO input jacks, press  
K
L
[SELECT] or [CH.  
/
] repeatedly until  
Even if there is a power failure of any kind, the  
unit will retain its memory for this feature.  
“AUX” appears on the screen.  
- 15 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Playback of poorly recorded or worn VCR tapes.  
If the unit displays a black box  
on the TV screen, this means that  
the unit is set to the TEXT mode.  
To clear screen, select [CAP-  
SLEEP TIMER  
TV/VCR  
The Sleep Timer function turns off the unit without  
using [POWER] after a desired period of time.  
NOTE:  
TION1], [CAPTION2] or [OFF].  
Make sure ...  
The unit must be turned on.  
This function does not work during Recording  
mode.  
1 Select “CAPTION”  
1 Call up the Sleep Timer Setting  
- TV/VCR SETUP -  
Press [SETUP].  
TIMER PROGRAMMING  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
Press [SLEEP] so that “SLEEP 0 MINUTE” appears.  
Press [K / L] to point to  
“CAPTION”.  
B
2 Set sleep time  
TIME SEARCH  
INDEX SEARCH  
Press [SLEEP] repeatedly until  
your desired sleep time appears.  
Each additional press will increase  
the time by 30 minutes up to 120  
minutes.  
After 5 seconds, the Sleep Timer setting will disap-  
pear automatically.  
2 Select your desired caption mode  
Press [ENTER] repeatedly until  
- TV/VCR SETUP -  
TIMER PROGRAMMING  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
SLEEP 120 MINUTE  
your desired caption menu  
appears.  
([CAPTION1], [CAPTION2],  
[TEXT1] or [TEXT2])  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [CAPTION1]  
ZERO RETURN  
B
TIME SEARCH  
INDEX SEARCH  
TO CANCEL THE SLEEP TIMER  
3 Exit the caption setting mode  
Press [SLEEP] to call up the Sleep Timer Setting.  
Press [SLEEP] repeatedly until “SLEEP 0 MINUTE”  
appears.  
Press [SETUP] to exit the menu.  
NOTE:  
Even if there is a power failure of any kind, the  
unit will retain its memory for this feature.  
CLOSED CAPTION SYSTEM  
TV/VCR  
TO CANCEL THE CLOSED CAPTION  
SYSTEM  
Repeat steps 1 to 2 and select [OFF] using  
[ENTER]. Then press [SETUP] to return to TV  
mode.  
You can view specially labeled (cc) TV programs,  
movies, news and pre-recorded tapes with either a  
dialogue caption or text display.  
CAPTION mode: You can watch dramas, movies and  
news while captioning the dialogues and the contents  
of news.  
TEXT mode: You can watch half screen text informa-  
tion if you want.  
1-2: You may get these captions or text information  
by selecting either “1” or “2”. Caption “2” is  
usually used for a second language if available.  
NOTES:  
Not all programs are broadcast with closed cap-  
tions. Your unit is designed to provide error free  
closed captions from high quality antenna, cable  
and VCR signals. Conversely, poor quality signals  
are likely to result in caption errors or no captions  
at all. Common signal conditions which may cause  
caption errors are listed below:  
Automobile ignition noise  
Electric motor brush noise  
Weak snowy reception on TV screen  
Multiplex signal reception displaying picture  
ghosts or airplane flutter.  
- 16 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ADDING/DELETING CHANNELS  
The channels you no longer receive or seldom watch  
can be deleted from the memory. (Of course, you can  
add the deleted channel into the memory again.)  
CHANNEL SET UP  
TV/VCR  
Make sure ...  
The unit must be turned on.  
- TV/VCR SETUP -  
TIMER PROGRAMMING  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
1 Select “CHANNEL SET UP”  
AUTO CHANNEL PROGRAMMING  
Press [SETUP].  
B
Press [K / L] to point to  
“CHANNEL SET UP”, then press  
[ENTER].  
As the initial setting, this unit has memorized all  
channels, including the ones not available in your  
area. This feature automatically puts only available  
channels into the memory.  
TIME SEARCH  
INDEX SEARCH  
– CHANNEL SET UP –  
2 Select “ADD/DELETE CH”  
Press [K / L] to point to  
“ADD/DELETE CH”, then press  
[ENTER].  
- TV/VCR SETUP -  
TIMER PROGRAMMING  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
1 Select “CHANNEL SET UP”  
B
ADD / DELETE CH (CATV)  
AUTO CH PROGRAMMING  
Press [SETUP].  
B
Press [K / L] to point to  
“CHANNEL SET UP”, then press  
[ENTER].  
TIME SEARCH  
INDEX SEARCH  
3 Enter the desired channel number  
2 Begin channel scanning  
Press [K / L] to point to  
K
L
Press [CH.  
/
] or the Number  
– CHANNEL SET UP –  
buttons until your desired channel  
number appears. (You can also  
press [K / L] to enter it.)  
ADD / DELETE CH (CATV)  
AUTO CH PROGRAMMING  
“AUTO CH PROGRAMMING”,  
then press [ENTER].  
08  
B
ADD / DELETE  
The tuner scans and memorizes all  
the active channels in your area.  
You must precede single-digit  
channel numbers with a zero  
(Example: 02 ... 09).  
(Example: CH8)  
When selecting cable channels which are higher  
than 99, press [+100] first, then press the last two  
digits. (Example: to select channel 125, first press  
[+100] then press [2] and [5].)  
3 After scanning  
The tuner stops on the lowest memorized channel.  
NOTES:  
When “AUTO CH PROGRAM-  
MING” is activated where there  
is no TV signal input, “NO TV  
SIGNALS” will appear on the  
display after the completion of  
channel scanning.  
NO TV SIGNALS  
4 Delete (or add) it from (or into) memory  
Press [ENTER]. The channel number changes to  
light red. The channel is deleted from memory.  
To delete another channel, repeat steps 3 to 4.  
If you press [ENTER] again, the channel is memo-  
rized again.  
The unit may recognize CATV channels to be TV  
channels if reception condition is poor. In this case,  
check the antenna connection and try “AUTO CH  
PROGRAMMING” again when reception condi-  
tions are better.  
Added channel : Light blue  
Deleted channel : Light red  
Channel memory programming is NOT neces-  
sary when connected to a cable box or satellite  
box. Just select the channel for cable box or  
satellite input (ex. CH3) on the unit, then select  
your desired channel on the cable box or satel-  
lite box.  
5 Exit the channel setup mode  
Press [SETUP] to exit the menu.  
NOTE:  
To confirm that channel(s) has been deleted or  
K
L
].  
added, press [CH.  
/
- 17 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CLOCK SET UP  
5 Select the year  
Press [K / L] until your desired  
year appears.  
(Example: “2005”)  
Then press [B].  
(AUTO / MANUAL)  
– MANUAL CLOCK SET –  
MONTH DAY  
YEAR  
2 0 0 5  
TV/VCR  
0 5  
/
:
0 6 FRI  
The unit clock must be set correctly so that VCR  
timer recording is possible. It is suggested that the  
clock be set manually when first setting up the unit,  
then set to [ON] the auto clock setting which will  
periodically correct the setting if necessary.  
NOTE:  
If you cannot receive a station with time signals,  
auto clock setting cannot be performed. Use manu-  
al setting only.  
HOUR  
– –  
MINUTE  
– – – –  
6 Select the hour  
Press [K / L] until your desired  
hour appears.  
(Example: “5”, “PM”)  
Then press [B].  
– MANUAL CLOCK SET –  
MONTH DAY  
YEAR  
2 0 0 5  
0 5  
/
:
0 6 FRI  
HOUR  
0 5  
MINUTE  
– – PM  
MANUAL CLOCK SETTING  
Make sure ...  
7 Select the minute  
Press [K / L] until the  
desired minute appears.  
(Example: “40”)  
– MANUAL CLOCK SET –  
MONTH DAY YEAR  
The unit must be turned on.  
In the example below, the clock is to be set to:  
0 5  
/
0 6 FRI  
2 0 0 5  
DATE  
SETTING TIME  
May 6th, 2005  
5:40PM  
HOUR  
0 5  
MINUTE  
4 0 PM  
:
1 Select “SETTING CLOCK”  
Press [SETUP].  
Press [K / L] to point to  
“SETTING CLOCK”, then press  
[ENTER].  
8 Start the clock  
- TV/VCR SETUP -  
TIMER PROGRAMMING  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
B
5:40 PM  
Press [SETUP].  
Although seconds are not displayed,  
they begin counting from 00 when  
you press [SETUP]. Use this fea-  
ture to synchronize the clock with  
the correct time.  
TIME SEARCH  
INDEX SEARCH  
2 Select “MANUAL CLOCK SET”  
Press [K / L] to point to  
“MANUAL CLOCK SET”, then  
press [ENTER].  
NOTE:  
– SETTING CLOCK –  
AUTO CLOCK  
[ON]  
When unplugging the AC cord or if there is a  
power failure for more than 3 seconds, you may  
have to reset the clock.  
AUTO CLOCK CH SEARCH  
AUTO CLOCK CH  
MANUAL CLOCK SET  
D.S.T.  
[ 02 ]  
B
[OFF]  
TO CHANGE CLOCK SETTING  
If you want to change the clock,  
1)Follow steps 1 to 2.  
2)Select the item you want to change using [B] .  
3)Enter correct numbers using [K / L].  
4)Press [SETUP] to start the clock.  
If there is no local PBS station in your area or on  
your cable system, select “AUTO CLOCK” and  
press [ENTER] to turn [OFF] this function before  
this step.  
3 Select the month  
Press [K / L] until your desired  
month appears.  
– MANUAL CLOCK SET –  
MONTH DAY  
YEAR  
0 5  
/
:
– – – – – – – – –  
(Example: May “05”)  
Then press [B]. (Or press [s] to  
go back one step.)  
HOUR  
– –  
MINUTE  
– – – –  
4 Select the day  
Press [K / L] until your desired  
day appears.  
– MANUAL CLOCK SET –  
MONTH DAY YEAR  
0 5  
/
0 6 – – – – – – –  
(Example: 6th “06”)  
Then press [B].  
HOUR  
– –  
MINUTE  
– – – –  
:
- 18 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AUTOMATIC CLOCK SETTING  
Make sure ...  
4 Enter the channel number that contains the  
The unit must be turned on.  
Confirm the unit is receiving a RF (Radio  
Frequency) signal from either an antenna or cable  
Automatic Clock Setting Signal  
– SETTING CLOCK –  
Press [RETURN] to go back to  
AUTO CLOCK  
[ON]  
“SETTING CLOCK” menu.  
Press [L] to select  
AUTO CLOCK CH SEARCH  
system connection using the ANT. jack on the rear  
of the unit.  
NOTES:  
B
AUTO CLOCK CH  
MANUAL CLOCK SET  
D.S.T.  
[
45]  
“AUTO CLOCK CH”.  
[OFF]  
If a cable converter box is being used, make sure it  
is powered on.  
You must use the remote control to perform the  
clock setting procedure.  
Press [s / B] until you locate Auto Clock Set station  
number.  
5 Exit the setting clock mode  
Press [SETUP] to exit the menu.  
If the unit is connected directly to a cable converter  
box or satellite box, the local PBS station must be  
selected on the cable box itself and the unit must be  
set to the output channel of the cable converter box  
or satellite box (usually channel 3 or 4), to be able  
to set up or correct the clock automatically.  
NOTE:  
Once the unit is turned off, it will periodically  
check and set the correct date and time.  
DAYLIGHT-SAVING TIME  
1 Select “SETTING CLOCK”  
- TV/VCR SETUP -  
TIMER PROGRAMMING  
TV/VCR  
Select this feature and the unit’s clock automatically  
will advance one hour in April, then reverse one hour  
in October.  
When Daylight-Saving Time is ON, the clock will  
change automatically as follows:  
Press [SETUP].  
B
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
Press [K / L] to select  
“SETTING CLOCK”, then press  
[ENTER] .  
TIME SEARCH  
INDEX SEARCH  
First Sunday of April : At 2 AM the clock immedi-  
2 Set “AUTO CLOCK” to [ON]  
Press [ENTER] to select [ON].  
– SETTING CLOCK –  
ately changes to 3 AM. Any timer programming  
you have set to occur between 2 AM and 3 AM will  
not record.  
Last Sunday of October : At 2 AM the clock  
immediately changes to 1 AM.  
B
AUTO CLOCK  
[ON]  
AUTO CLOCK CH SEARCH  
AUTO CLOCK CH  
MANUAL CLOCK SET  
D.S.T.  
[ 02 ]  
[OFF]  
Make sure ...  
3 Begin “AUTO CLOCK CH SEARCH”  
The unit must be turned on.  
Press [L] to select “AUTO CLOCK  
CH SEARCH”.  
– SETTING CLOCK –  
AUTO CLOCK  
[ON]  
B
AUTO CLOCK CH SEARCH  
1 Select “SETTING CLOCK”  
Press [SETUP].  
Press [K / L] to point to  
“SETTING CLOCK”, then press  
[ENTER].  
Then press [ENTER].  
- TV/VCR SETUP -  
TIMER PROGRAMMING  
AUTO CLOCK CH  
MANUAL CLOCK SET  
D.S.T.  
[ 02 ]  
The unit begins searching for the  
B
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
[OFF]  
station which contains the auto  
clock set signal. The search for a  
TIME SEARCH  
INDEX SEARCH  
signal may take up to 20 seconds per channel.  
When the search has ended, “_ _”  
– AUTO CLOCK CH SEARCH –  
appears at the lower left of the  
screen.  
08  
10  
13  
2 Set “D.S.T.(Daylight-Saving Time) to [ON]  
Press [K / L] to point to “D.S.T.”,  
then press [ENTER] until [ON]  
appears.  
– SETTING CLOCK –  
Write down the number(s) that  
appear on the screen. They are the  
auto clock station(s) in your area.  
AUTO CLOCK  
[ON]  
_ _  
AUTO CLOCK CH SEARCH  
AUTO CLOCK CH  
MANUAL CLOCK SET  
D.S.T.  
[ 02 ]  
[ON]  
If no number(s) appear on the TV screen, there are  
no stations in your area which contain the Auto  
Clock signal. Auto Clock Setting is not possible.  
Please use Manual Clock Setting on page 18.  
B
3 Exit the Daylight-Saving Time mode  
Press [SETUP] to exit the menu.  
NOTE:  
During AUTO CLOCK CH SEARCH, the picture  
may be distorted.  
TO CANCEL THE DAYLIGHT-SAVING  
TIME  
Repeat steps 1 to 2 and select [OFF] using [ENTER].  
- 19 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTES:  
V-CHIP SET UP  
When you select a rating and set  
it to [BLOCK], the higher ratings  
will be blocked automatically.  
The lower ratings will be avail-  
able for viewing.  
TV–Y  
TV–Y7  
TV–G  
TV–PG (DLSV)  
TV–14 (DLSV)  
TV–MA( LSV)  
[VIEW]  
[VIEW]  
[BLOCK]  
[BLOCK]  
[BLOCK]  
[BLOCK]  
TV/VCR  
(
)
B
This feature enables parents to prevent their children  
from watching inappropriate material on TV. When  
you try to access a program which is blocked,  
“PROTECTED PROGRAM by ...” message appears  
on the TV screen.  
When you set the lowest rating to  
[VIEW], all other ratings will automatically be  
available for viewing.  
V-CHIP SET UP  
5 Setting “Sub-Ratings”  
Make sure ...  
TV–Y  
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
When you select the ratings of TV-  
B
TV–Y7  
TV–G  
(
)
The unit must be turned on.  
Y7, TV-PG, TV-14 or TV-MA you  
will have the option of setting sub  
rating categories.  
Press [K / L] to select a rating with  
sub-ratings you wish to block, then  
press [ENTER] twice.  
Press [K / L] to select a sub-rating,  
then press [ENTER] to set it to  
[BLOCK] or [VIEW].  
TV–PG (  
)
)
)
TV–14  
(
TV–MA(  
1 Select “V-CHIP SET UP”  
Press [SETUP].  
Press [K / L] to select “V-CHIP  
SET UP”, then press [ENTER].  
- TV/VCR SETUP -  
TIMER PROGRAMMING  
SETTING CLOCK  
CHANNEL SET UP  
TV–Y7  
FV  
[BLOCK]  
[BLOCK]  
USER’S SET UP  
B
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
B
INDEX SEARCH  
2 Enter Access code  
Press the Number buttons to  
enter the access code.  
TV–PG  
[BLOCK]  
B
D
L
S
V
[BLOCK]  
[BLOCK]  
[BLOCK]  
[BLOCK]  
ACCESS CODE  
_
_
_
_
For the first time set-up or in the  
event the unit has lost power,  
enter the default code of 0000.  
Selection  
TV-Y7  
FV  
Rating Category Explanations  
Fantasy Violence  
3 Select the desired item  
TV-PG, TV-14, TV-MA  
Press [K / L] to select “TV RATING”, “MPAA RAT-  
ING” or “CHANGE CODE”, then press [ENTER].  
Refer to the pages below to set up each item.  
– V-CHIP SET UP –  
D
L
S
Suggestive Dialog (TV-PG, TV-14 only)  
Coarse Language  
Sexual Situation  
Violence  
A
B
C
P 20 Step  
P 21 Step  
4
4
4
B TV RATING  
MPAA RATING  
CHANGE CODE  
V
NOTE:  
The blocked sub-ratings will  
appear next to the rating category  
in the “TV RATING” menu.  
P 21 Step  
TV–Y  
TV–Y7  
TV–G  
TV–PG (DLSV)  
TV–14 (DLSV)  
TV–MA ( LSV)  
[VIEW]  
(
)
[VIEW]  
[VIEW]  
B
[BLOCK]  
[BLOCK]  
[BLOCK]  
A
TV RATING SET UP  
Follow steps to in the “V-CHIP SET UP” sec-  
1
3
tion above.  
6 Exit the V-Chip setting mode  
Press [SETUP] to exit the menu.  
4 Blocking TV programs  
Press [K / L] to select a rating that  
you wish to block.  
Press [ENTER] repeatedly to set it  
to [BLOCK] or [VIEW].  
B
TV–Y  
TV–Y7  
TV–G  
TV–PG (  
TV–14  
TV–MA(  
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
NOTE:  
(
)
)
)
)
To change the rating, the TV must  
(
PROTECTED PROGRAM  
by TV-Y  
be turned to an unprotected pro-  
gram. If “PROTECTED PRO-  
GRAM by ...” appears on the  
screen, please change the channel  
to a station that is not protected.  
Selection  
TV-Y  
Rating Category Explanations  
Appropriate for all children  
TV-Y7  
TV-G  
Appropriate for children seven and older  
General Audience  
TV-PG  
TV-14  
Parental Guidance suggested  
Unsuitable for children under 14  
TV-MA Mature audience only  
- 20 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
B
MENU LANGUAGE  
MPAA RATING SET UP  
TV/VCR  
Follow steps to in the “V-CHIP SET UP” section  
on page 20.  
1
3
1 Select “LANGUAGE”  
Press [SETUP].  
Press [K / L] to point to  
“LANGUAGE”.  
- TV/VCR SETUP -  
4 Select your desired item  
Press [K / L] to point to your  
desired item, then press [ENTER]  
to select [BLOCK] or [VIEW].  
TIMER PROGRAMMING  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
G
[VIEW]  
PG  
[VIEW]  
PG–13  
R
NC–17  
X
[VIEW]  
B
[BLOCK]  
[BLOCK]  
[BLOCK]  
B
TIME SEARCH  
INDEX SEARCH  
Selection  
G
PG  
PG-13  
R
Rating Category Explanations  
General Audience  
Parental Guidance suggested.  
Unsuitable for children under 13  
Restricted; under 17 requires accompa-  
nying parent or adult guardian  
No one under 17 admitted  
2 Select “ENGLISH”, “ESPAÑOLor “FRANÇAIS”  
Press [ENTER] repeatedly to select “ENGLISH”,  
“ESPAÑOL”= Spanish or “FRANÇAIS”= French.  
3 Exit the Language mode  
Press [SETUP] to exit the menu.  
NOTES:  
NC-17  
X
Mature audience only  
This function effects only the language on the  
screen menu and not the audio source.  
When you select a rating and set it to [BLOCK],  
the higher ratings will be blocked automatically.  
The lower ratings will be available for viewing.  
When you set the lowest rating to [VIEW], all  
other ratings will automatically be available for  
viewing.  
If for some reason the menu is in Spanish or  
French, press [SETUP], press [K / L] to point to  
“IDIOMA [ESPAÑOL]” or “LANGAGE  
[FRANÇAIS]”, then press [ENTER] repeatedly to  
select desired language, then press [SETUP].  
5 Exit the V-Chip setting mode  
Press [SETUP] to exit the menu.  
C
CHANGE ACCESS CODE  
Follow steps to in the “V-CHIP SET UP” sec-  
1
3
tion on page 20.  
4 Enter New code  
NEW CODE  
X X X X  
Press the Number buttons to enter  
your desired access code in the  
“NEW CODE” space, then enter  
the same code in the “CONFIRM  
CONFIRM CODE  
_
_
_
_
CODE” space. When completed, the menu will  
return to “V-CHIP SET UP”.  
Make sure you enter exactly the same new code in  
the “CONFIRM CODE” space as one in the  
“NEW CODE” space. If they are different, the  
“NEW CODE” space is cleared for redoing.  
5 Exit the V-Chip setting mode  
Press [SETUP] to exit the menu.  
NOTE:  
Your personal access code will be erased and will  
return to the default (0000) when a power failure  
occurs or when you turn off the power using a  
wall switch. If you have forgotten the code, unplug  
the power cord for 10 seconds to restore the access  
code to 0000.  
- 21 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIDEO CASSETTE  
This unit will operate with any cassette that has the  
mark. For best results, we recommend the use of  
high-quality tapes. Do not use poor quality or damaged tapes.  
PRECAUTIONS  
INSERTING A CASSETTE  
Avoid moisture. Moisture condensation may occur  
Insert the cassette in the direction as shown. Push in  
gently, but continuously, on the center-back of the  
cassette until it is drawn into the unit. The unit will  
automatically turn on.  
on the tape if it is moved from a cold place to a  
warm place or vice versa. Before using a tape with  
these conditions, to avoid damage of the tape and  
your unit, wait until the tape has warmed to room  
temperature and the moisture has evaporated.  
Avoid extreme heat, high humidity and magnetic  
fields.  
Window  
Do not tamper with the cassette mechanism.  
Do not touch the tape with your fingers.  
WRONG  
CORRECT  
TWO DIFFERENT TAPE SPEEDS  
REMOVING A CASSETTE  
Before recording, select the tape speed from : SP  
mode (Standard Play) or SLP mode (Super Long  
Play).  
The table below shows the maximum recording/play-  
back time using T60, T120 or T160 tapes in each  
mode.  
1)In the stop mode, press [C A STOP/EJECT] on  
the unit. The cassette will be ejected.  
2)Pull the cassette out of the cassette compartment.  
3)Store the cassette in its case as shown.  
Tape Speed  
Type of tape  
SP mode  
Recording/Playback Time  
T60  
1 hour  
3 hours  
T120  
T160  
2 hours 2-2/3 hours  
6 hours 8 hours  
SLP mode  
ERASE PREVENTION  
NOTE:  
You can play back a tape recorded in LP mode  
(Long Play).  
You can prevent accidental  
erasing of recording by  
breaking off the tab on the  
back edge of the cassette.  
Tab  
If you decide to record on  
the tape again, cover the  
hole with plastic tape.  
Plastic Tape  
NOTE:  
In DVD mode, whether the cassette is with tab or  
without tab you insert, it doesn’t start playing until  
[B PLAY]  
you press  
.
In TV/VCR mode, if the cassette without tab is  
inserted, playback will automatically start.  
- 22 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PLAYBACK  
NORMAL PLAYBACK  
SLOW MOTION  
TV/VCR  
TV/VCR  
Press [PAUSE F], then press [D] to start the play-  
back in slow motion. The unit mutes the sound dur-  
ing slow motion. Press [PLAY O] to return to nor-  
mal playback.  
Make sure ...  
The unit must be turned on.  
1 Insert a prerecorded tape  
If the erase-prevention tab has been removed, the  
unit will start playback automatically.  
NOTE:  
If it is left in the Slow mode for more than 5 min-  
utes, the unit will automatically go into the stop  
mode.  
B
PLAY  
2 To begin playback  
Press [PLAY O].  
STILL PICTURE  
TV/VCR  
You can view a still picture on the TV screen during  
playback (the Still mode). Press [PAUSE F] during  
playback. Only tapes recorded in the SLP mode will  
show the least amount of lines. Press [PLAY O] to  
return to playback.  
3 To stop playback  
Press [STOP C].  
STOP  
NOTES:  
You can advance the picture one frame at a time by  
pressing [PAUSE F] during the Still mode.  
If it is left in the Pause mode for more than 5 min-  
utes, the unit will automatically switch to the stop  
mode.  
NOTES:  
Even in the DVD mode, you can start the VCR  
playback if you press [ PLAY] (of the TV/VCR  
side).  
B
VCR playback will stop and the mode will change  
to the DVD mode by pressing [SELECT],  
VERTICAL HOLD CONTROL  
B
[
A
PLAY] (DVD side) or [ OPEN/CLOSE].  
TV/VCR  
In the Pause/Still mode only, when the picture begins  
to vibrate vertically, stabilize the picture by pressing  
TRACKING ADJUSTMENT  
K
L
].  
[CH.  
NOTE:  
/
TV/VCR  
Tracking adjustment will be set automatically  
(Digital Tracking function) when you start play-  
back.  
If there are video noise lines on the screen, refer to  
TRACKING ADJUSTMENT on this page.  
Noise lines (black and white streaks) may appear  
on the playback picture when playing pre-recorded  
tapes or tapes recorded on other VCR. If this  
K
L
occurs, press [CH.  
/
] until the streaks disap-  
pear.  
You can reduce the noise lines by pressing  
K
L
[CH.  
/
] in Slow mode too. Tracking adjust-  
ment in Slow mode will not be set automatically.  
To return to the Digital Auto Tracking function,  
stop the tape once and start playback.  
- 23 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPECIAL PLAYBACK  
Make sure ...  
AUTO REPEAT PLAYBACK  
The unit must be turned on.  
Insert a prerecorded tape.  
TV/VCR  
The unit has the auto repeat function that allows you to  
repeat a tape indefinitely without pressing [PLAY O].  
ALL REPEAT: Repeat playback from the beginning  
to the end of the tape.  
BLANK REPEAT: Repeat playback from the begin-  
ning to a blank part, which is blank for more than  
10 seconds.  
RENTAL PLAYBACK  
TV/VCR  
This function enables you to improve the picture  
quality when playing back worn cassettes such as  
rented tapes.  
1 Select “USER’S SET UP”  
- TV/VCR SETUP -  
1 Select “USER’S SET UP”  
- TV/VCR SETUP -  
TIMER PROGRAMMING  
SETTING CLOCK  
Press [SETUP].  
TIMER PROGRAMMING  
CHANNEL SET UP  
SETTING CLOCK  
Press [SETUP].  
B
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
CHANNEL SET UP  
Press [K / L] to point to “USER’S  
SET UP”, then press [ENTER].  
B
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
Press [K / L] to point to “USER’S  
SET UP”, then press [ENTER].  
INDEX SEARCH  
INDEX SEARCH  
USER’S SET UP  
2 Set “RENTALto [ON]  
Press [K / L] to point to  
“RENTAL”.  
2 Select “ALLor “BLANK”  
Press [K / L] to point to “REPEAT  
PLAY”.  
Press [ENTER] repeatedly until  
your desired selection [ALL] or  
[BLANK] appears.  
USER’S SET UP  
B
RENTAL  
[ON]  
[OFF]  
[OFF]  
REPEAT PLAY  
AUTO RETURN  
RENTAL  
[OFF]  
[ALL]  
[OFF]  
B
REPEAT PLAY  
AUTO RETURN  
Press [ENTER] until [ON] appears.  
3 Exit the Rental setting  
Press [SETUP] to return to the TV mode.  
3 Exit the Repeat Play setting  
Press [SETUP] to return to the TV mode.  
4 Start playback  
Press [PLAY O] to start playback.  
“RENTAL PLAY B” appears.  
4 Start playback  
Press [PLAY O] to start the Repeat Play.  
“REPEAT PLAY B” appears.  
Once you select the Rental mode, it stays in effect  
even after you turn off the unit.  
Once you select the Repeat Play mode, it stays in  
effect even after you turn off the unit.  
If the Rental mode is set [ON], the “RENTAL  
PLAY B” display has priority.  
TO CANCEL THE RENTAL MODE  
Repeat steps 1 to 2 and select [OFF] using  
[ENTER]. Press [SETUP] to return to TV mode.  
Even if there is a power failure of any kind, the  
unit will retain its memory for this feature.  
TO CANCEL THE REPEAT PLAY MODE  
Repeat steps 1 to 2 and select [OFF] using  
[ENTER]. Press [SETUP] to return to TV mode.  
Even if there is a power failure of any kind, the  
unit will retain its memory for this feature.  
- 24 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SEARCH  
Make sure ...  
NOTE:  
Tapes recorded in the SP or LP mode will normally  
The unit must be turned on.  
display a noise bar on the TV screen and the pic-  
ture may revert to Black and White.  
Insert a tape.  
ZERO RETURN  
3 Return to normal speed  
Press [PLAY O].  
TV/VCR  
This function allows you to search easily a beginning  
point that you want to review by rewinding or fast  
forwarding.  
NOTE:  
TIME SEARCH  
TV/VCR  
Zero Return WILL NOT work on a blank tape or  
The Time Search function makes it possible to quick-  
ly advance the tape to your desired position simply  
by entering the exact amount of playback time you  
want to skip.  
a blank portion of a tape.  
1 Stop a tape at your desired point  
Rewind or fast forward the tape to the beginning  
point at which you want to review.  
NOTE:  
Time Search can be set up to a maximum of 9  
hours 50 minutes (9:50) by 10 minutes at a time.  
In the example below: To watch a program before/  
after 2 hour 50 minutes from the present position, in  
either direction.  
2 Reset the counter to 0:00:00  
Press [C.RESET] repeatedly.  
3 Begin recording or playback  
Press [RECORD] or [PLAY O].  
Press [STOP C] when recording or playback is com-  
pleted.  
- TV/VCR SETUP -  
1 Select “TIME SEARCH”  
TIMER PROGRAMMING  
SETTING CLOCK  
CHANNEL SET UP  
Press [SETUP].  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
INDEX SEARCH  
Press [K / L] to point to “TIME  
SEARCH”, then press [ENTER].  
B
4 To activate “ZERO RETURN”  
Press [SETUP].  
- TV/VCR SETUP -  
TIMER PROGRAMMING  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
2 Enter your desired time  
Press [K / L] until your desired time  
appears. (Example: “2:50” stands for  
2 hours 50 minutes)  
Press [K / L] to point to “ZERO  
RETURN”, then press [ENTER].  
The unit will begin rewinding and  
the counter will appear on the TV  
screen.  
TIME SEARCH  
2 : 50  
B
TIME SEARCH  
INDEX SEARCH  
If you wish to cancel the Time  
Search at this point, press  
[SETUP].  
The tape will automatically stop when the counter  
returns to 0:00:00 (approx.).  
3 Begin Time Search  
PICTURE SEARCH  
By pressing [s B], the unit will rewind or fast for-  
/
ward to the specified point.  
TV/VCR  
The time counts down during the search. When the  
display shows “0:00”, the tape will start playback  
automatically.  
This feature is very useful in finding or skipping over  
a particular scene on a tape. In this mode, the sound  
will be muted.  
TO CANCEL DURING TIME SEARCH  
Press [C A STOP/EJECT] on the unit or  
[STOP C]. This will delete the selected time.  
1 Start Picture Search  
During playback, press [D] or [E] to view at a  
high speed (in forward/reverse).  
2 Change searching speed  
Press [D] or [E] again to view at super high  
speed (in the LP/SLP modes only).  
- 25 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
- TV/VCR SETUP -  
INDEX SEARCH  
1 Select “INDEX SEARCH”  
Press [SETUP].  
Press [K / L] to point to “INDEX  
SEARCH”, then press [ENTER].  
TIMER PROGRAMMING  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TV/VCR  
This feature provides a method of indexing the start-  
ing point so that it can be easily returned to in either  
fast forward or rewind mode.  
TIME SEARCH  
INDEX SEARCH  
B
The index mark will be made automatically when  
[RECORD] is pressed. It will also be marked at  
the starting point of Timer recording and OTR.  
The index mark will not be recorded if [PAUSE  
F] is pressed and released during recording.  
The time gap between making the index marks on  
the tape should be greater than 1 minute for SP  
recording, 2 minutes for LP recording and 3 min-  
utes for SLP recording.  
2 Enter your desired number  
Press [K / L] until the number of  
programs that you want to skip  
appears.  
INDEX SEARCH  
0 3  
(Example: “03” for 3 programs)  
The Index Search mode will be canceled if the pro-  
cedures are not activated in 30 seconds.  
In some cases, the index mark at the beginning of  
video tape cannot be detected.  
Example: You are watching program number 4 and  
want to fast forward to program number 7. You  
must skip three programs.  
3 Begin Index Search  
Press [s B]. The unit begins rewinding or fast for-  
/
warding to the beginning of desired program.  
NOTE:  
Every time an index signal is skipped, the number  
in the program indicator decreases by one.  
CURRENT PLAYBACK PROGRAM  
Beginning of  
the tape  
End of  
the tape  
4 After Index Search  
When the preset program is reached, the unit will  
start playback automatically.  
Pro.1 Pro.2 Pro.3 Pro.4 Pro.5 Pro.6 Pro.7  
4
3
2
1
1
2
3
A video cassette must be inserted in the unit for  
this function to work.  
INDEX MARK  
The number of Index Searches can be set up to 20.  
This function will not operate in the Recording  
mode.  
When you want to cancel the Index Search while  
in progress, press [STOP C].  
- 26 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPECIAL FEATURES  
REAL TIME TAPE COUNTER  
AUTO REWIND-EJECT  
TV/VCR  
TV/VCR  
When the end of a tape is reached during record-  
ing, playback, or fast-forward, the tape will auto-  
matically rewind to the beginning. After rewinding  
finishes, the unit will eject the tape and turn itself  
off.  
This shows the elapsed recording or playback time in  
hours, minutes, and seconds. (The displayed time will  
not change on a blank tape or blank portions on the  
tape.) The “–” indication will appear when the tape has  
rewound further than “0:00:00” on the tape counter.  
This function is operative when Repeat Play is set  
to the [OFF] position.  
The tape will not auto-rewind during timer record-  
ing or One Touch Recording.  
- 27 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RECORDING  
Make sure ...  
The unit must be turned on.  
Insert a cassette tape with its erase-prevention tab in place. (If necessary, rewind or fast forward the tape to  
the point at which you want to begin recording.)  
NOTES:  
This unit will ONLY record and view the same channel.  
This unit cannot record the contents from the built-in DVD.  
SKIPPING UNWANTED  
NORMAL RECORDING  
SCENES DURING RECORDING  
TV/VCR  
TV/VCR  
You can ONLY watch the same TV program that is  
being recorded.  
Press [PAUSE F] to temporarily  
stop recording.  
PAUSE  
Press [PAUSE F] or [RECORD]  
to resume recording.  
NOTES:  
1 Select the channel to be recorded  
Press the Number buttons or  
SP  
CH 10  
K
L
].  
[CH.  
/
After 5 minutes, the unit will  
automatically switch to the Recording mode to pre-  
vent tape damage.  
NOTE:  
If Closed Caption mode is on, the On-Screen  
Display will appear for 5 seconds, then disappear.  
If the unit is connected to a cable box or satellite  
box, the unit must be on CH3 or CH4, then the  
channel to be recorded must be selected on the  
cable box or satellite box.  
2 Select the tape speed  
Press [SPEED] to select the desired  
tape speed (SP/ SLP).  
SP  
REC  
3 Begin recording  
Press [RECORD].  
SP  
4 Stop recording  
Press [STOP C].  
- 28 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Time(s)  
1 time  
Display  
Recording length  
(normal recording)  
OTR (One Touch Recording)  
2 times  
3 times  
0:30  
1:00  
30 minutes  
60 minutes  
TV/VCR  
This function enables you to set a recording length  
simply by pressing [ REC/OTR] on the unit.  
I
17 times  
8:00  
480 minutes  
Make sure ...  
The unit must be turned on.  
Insert a cassette tape with its erase-prevention tab  
in place. (If necessary, rewind or fast forward the  
COPYING A VIDEO CASSETTE  
(Requires a VCR or camcorder)  
tape to the point at which you want to begin  
recording.)  
NOTES:  
TV/VCR  
You can make copies of video tapes made by friends  
or relatives for your enjoyment.  
You can not copy a DVD to a videotape.  
You cannot start OTR with the remote control.  
I
Recording starts immediately when [ REC/OTR]  
is pressed.  
When [REC/OTR] is pressed 18 times, the unit  
WARNING: Unauthorized recordings of  
copyrighted video tapes may be an  
infringement of copyright laws.  
returns to the Normal Recording mode.  
To stop the OTR operation, press [C STOP] on  
the unit or on the remote control.  
To show the remaining time, press [DISPLAY] on  
the remote control so that “OTR” appears on the  
TV screen. (It will show up momentarily then dis-  
appear.)  
Connect your unit and a source (Playing) VCR using  
the following diagram.  
[This unit]  
[Fig.8]  
Recording stops when the display shows 0:00.  
Please note that in the SLP mode maximum  
recording time, assuming the tape is started at the  
beginning, is 8 hours using T-160 (or 6 hours  
using T-120).  
[Ex: Source VCR or  
camcorder]  
If the tape runs out before the end time, the unit  
will switch to the stop mode immediately, ejects  
the tape and turns itself off.  
Even if [POWER] is pressed during OTR, the unit  
continues recording.  
AUDIO  
Audio/Video  
cable  
(not supplied)  
L
OUT  
IN  
R
VIDEO  
OUT  
IN  
1 Select the channel to be recorded  
1)Insert a pre-recorded video cassette into the source  
VCR or camcorder.  
2)Insert a blank video cassette or one you want to  
record over, into the unit’s cassette compartment.  
3)Press [SPEED] on remote control for the unit to  
select the desired recording speed (SP/SLP).  
K
L
].  
Press the Number buttons or [CH.  
/
NOTE:  
If the unit is connected to a cable box or satellite  
box, the unit must be on CH3 or CH4, then the  
channel to be recorded is selected on the cable box  
or satellite box.  
K
L
4)Press [CHANNEL  
/
] on the unit until “AUX”  
appears on the screen.  
2 Select the tape speed  
I
5)Press [ REC/OTR] on the unit.  
Press [SPEED] to select the desired tape speed  
6)Begin playback of the tape in the source VCR or  
camcorder.  
(SP/SLP).  
NOTE:  
For best results during copying, use the front  
3 Begin OTR  
panel controls whenever possible. The remote  
control might affect the source VCR’s playback  
operation.  
I
OTR (2 : 30)  
Press [ REC/OTR] on the unit as  
many times as needed. The record-  
ing length will be determined by  
the number of times you press  
I
7)To stop copying, press [C A STOP/EJECT] on  
the unit, then stop the tape on the source VCR or  
camcorder.  
[
REC/OTR]. Each time it is  
SP  
pressed, the recording time will be  
increased by 30 minutes up to 8 hours.  
- 29 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TIMER RECORDING  
AUTOMATIC TIMER  
RECORDING  
1 Select “TIMER PROGRAMMING”  
- TV/VCR SETUP -  
Press [SETUP].  
B
TIMER PROGRAMMING  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
Confirm “TIMER PROGRAM-  
MING” is pointed by pressing [K],  
then press [ENTER].  
TV/VCR  
You may set the unit to start and end a recording  
while you are away. You can set 8 programs to record  
on specific days, daily or weekly within a 1 year  
period.  
TIME SEARCH  
INDEX SEARCH  
If you have not yet set the clock,  
“MANUAL CLOCK SET” appears. If so, follow  
steps 3 to 8 on page 18. Then set the timer record-  
ing.  
In the example below, the timer is being set to record:  
DATE:  
July 4th, 2005  
SETTING TIME: from 7:30PM to 8:50PM  
2 Select your desired program position (1 to 8)  
CHANNEL:  
TAPE SPEED:  
CH61  
SP  
Press [K / L] to select the desired  
– TIMER PROGRAMMING –  
CH DATE  
BEGIN END  
program position, then press [B].  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
Make sure ...  
B
If a cable box or satellite box is connected with the  
unit you will be limited to record only one channel,  
and the channel selector on the unit must be select-  
ed to the output channel of the boxes CH 3 or CH  
4 and then the actual channel to be recorded must  
be selected on the boxes.  
3 Set the channel number  
Press [K / L] until the desired  
channel number appears (Example:  
CH61), then press [B].  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
61 -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
Clock must be set to the correct time and date  
before setting the timer.  
B
The unit must be turned on to program it.  
Insert a cassette tape with its erase-prevention tab  
in place. (If necessary, rewind or fast forward the  
tape to the point at which you want to begin  
recording.)  
NOTE:  
If the unit is connected to a cable box or satellite  
box, the unit must be on CH3 or CH4, then the  
channel to be recorded is selected on the cable box  
or satellite box.  
The channel you want to record is properly set in  
advance. (Refer to page 17.)  
Avoid overlap of programs ...  
There is a chance that a program will not be record-  
ed, when programs overlap;  
4 Select once, every day or weekly recording  
For once recording :  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
Press [K] until the desired date  
appears.  
(Example: “7/04” for July 4th)  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
61 7/04 MON -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
The program with an earlier start has priority.  
Once the earliest program finishes, the overlapping  
programs will begin recording in sequence.  
B
Then press [B].  
When the starting time is the same, the program set  
on the highest position in the program list has pri-  
ority.  
The illustration below demonstrates the sequence  
of recordings.  
For every day recording : To record a TV program  
at the same time on the same channel every day.  
(Example: Monday through Sunday)  
– TIMER PROGRAMMING –  
CH DATE  
BEGIN END  
Program 1  
Program 2  
Program 3  
10:00AM - 11:00AM  
9:00AM - 10:00AM  
9:30AM - 12:00PM  
Press [L] until “EVRY DAY”  
appears, then press [B].  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
61 EVRY DAY -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
B
Recording Sequence  
For weekly recording : To record a TV program at  
the same time on the same channel every week.  
Program 1  
10:00AM-11:00AM  
Program 2  
9:00AM-10:00AM  
Program 3  
(Example: every Monday)  
– TIMER PROGRAMMING –  
CH DATE  
BEGIN END  
9:30AM-12:00PM  
Press [L] until “EVRY” and  
your desired day of the week  
appear together, then press [B].  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
61 EVRY MON -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
9:00AM  
10:00AM  
11:00AM  
12:00PM  
B
*Recording period is SHADED  
- 30 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTES:  
5 Set beginning hour  
Press [K / L] until the desired hour  
appears.  
(Example: “ 7, PM” for 7:30PM)  
Then press [B].  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
The display will not be turned on automatically at  
the time the programmed recording begins. To  
watch the currently recorded TV program or to  
play a DVD disc, press [POWER] and [SELECT]  
to choose the TV/VCR mode or the DVD mode.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
61 7/04 MON 7:12P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
M
B
If the tape runs out before the end time, the unit  
will switch to the stop mode immediately and the  
tape will be ejected.  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
6 Set beginning minute  
Press [K / L] until the desired  
minute appears.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
61 7/04 MON 7:30P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
M
B
TIMER PROGRAM EXTENSION  
(Example: “30” for 7:30PM)  
Then press [B].  
To shift the time schedule of an automatic timer  
recording.  
1)Press [POWER].  
2)Repeat step 1 on page 30.  
3)Press [RECORD] and select the desired program  
using [K / L].  
4)Press [RECORD] again.  
7 Set end hour  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
Press [K / L] until the desired hour  
appears.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
8:30PM- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
61 7/04 MON 7:30P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
M
B
(Example: “8, PM” for 8:50PM)  
Then press [B].  
Each additional push will shift forward the  
begin/end time for recording by 10 minutes. When  
the recording is already in progress, each additional  
push will shift forward the end time only. If you  
want to cancel while setting, press [PAUSE F] on  
the remote control. The recording time returns to  
the original time.  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
8 Set end minute  
Press [K / L] until the desired  
minute appears.  
(Example: “50” for 8:50PM)  
Then press [B].  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
8:50PM- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
61 7/04 MON 7:30P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
M
B
NOTE:  
9 Set the tape speed  
Press [K / L] until the desired tape  
speed appears. (Example: “SP”)  
When you shift forward the time schedule during  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
recording, the recording speed will automatically  
be set to the SLP mode.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
8:50PMSP  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
61 7/04 MON 7:30P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
M
B
5)Press [ENTER] or [RETURN] to exit the setting  
menu. Then press [SETUP] to return to original  
mode.  
10 Finish setting the program  
TO CORRECT A PROGRAM  
Press [ENTER] or [RETURN] to complete setting.  
While setting a program; press [s] to go back one  
step and enter the correct numbers using [K / L].  
To set another program, repeat steps 2 to 10.  
Press [SETUP] to exit the menu.  
After setting a program;  
1)Press [POWER].  
11 Set the timer  
Press [POWER] to set automatic timer recording.  
The recording indicator lights up.  
2)Repeat steps 1 to 2 on page 30.  
3)Press [B] (or press [s] to go back one step)  
until the part you want to correct begins flashing,  
then make the changes using [K / L].  
4)Press [POWER] to set automatic timer recording.  
You must turn off the unit to activate automatic  
timer recording.  
If power is not turned off and you continue watch-  
ing TV, TIMER REC STANDBY” starts flashing  
on the TV screen 2 minutes before the programmed  
start time.  
TO CANCEL AN AUTOMATIC TIMER  
RECORDING  
If the erase-prevention tab is removed, the cassette  
will be ejected when [POWER] is pressed to off.  
1)Press [POWER].  
2)If recording is in progress, press  
[C A STOP/EJECT] on the unit.  
3)Repeat steps 1 to 2 on page 30 and select a pro-  
gram you want to cancel.  
4)Press [C.RESET].  
5)Press [SETUP] to return to TV mode.  
- 31 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TO CONFIRM THE TIMER SETTING  
1)Press [POWER] so that the Recording indicator  
light goes off.  
AUTO RETURN  
TV/VCR  
2)Press [SETUP].  
With this feature, after timer recording is finished,  
the beginning of the recorded program(s) can be  
searched for automatically.  
3)Confirm “TIMER PROGRAMMING” is selected.  
4)Press [ENTER]. The details of programs appear on  
the TV screen.  
5)Press [SETUP] to return to TV mode.  
1 Select “USER’S SET UP”  
- TV/VCR SETUP -  
TIMER PROGRAMMING  
SETTING CLOCK  
Press [SETUP].  
CHANNEL SET UP  
B
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
Press [K / L] to point to “USER’S  
SET UP”, then press [ENTER].  
INDEX SEARCH  
2 Set “AUTO RETURN” to [ON]  
Press [K / L] to point to “AUTO  
RETURN”, then press [ENTER]  
until [ON] appears.  
USER’S SET UP  
RENTAL  
[OFF]  
[OFF]  
[ON]  
REPEAT PLAY  
AUTO RETURN  
B
3 Auto Return will begin  
When all the timer recordings are completed, the unit  
will rewind to the beginning of the recorded pro-  
gram(s).  
NOTE:  
If you press [POWER] while tape is rewinding,  
the Auto Return will stop.  
4 Watch the recorded program  
Press [PLAY O].  
TO CANCEL THE AUTO RETURN  
MODE  
Repeat steps 1 to 2 and select [OFF] using  
[ENTER].  
Even if there is a power failure of any kind, the  
unit will retain its memory for this feature.  
- 32 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ON SCREEN DISPLAY  
To check the Counter, Clock and Channel number on the TV screen, press [DISPLAY]. Each time you press  
[DISPLAY], the TV screen will change as follows:  
When the Closed Caption mode is OFF:  
When the Closed Caption mode is ON:  
Counter mode: After 5 seconds, only the counter  
remains. To clear it, press [DISPLAY].  
Clock mode: After 5 seconds, only the clock and  
the channel number remain. To clear them, press  
The On Screen Display disappear after 5 seconds.  
This is true even if [MUTE] or [PAUSE F] is  
pressed while recording.  
[DISPLAY].  
OFF mode  
Clock/Counter mode  
OFF mode Counter mode  
Clock mode  
STOP  
STOP  
5:40PM  
CH2  
STOP  
5:40 PM  
CH2  
SP  
COUNT 0:12:34  
SP  
SP  
COUNT 0:12:34  
After 5 seconds  
After 5 seconds  
5:40PM  
CH2  
COUNT 0:12:34  
Counter  
remains  
Clock & Channel  
remains  
CABLE CHANNEL DESIGNATIONS  
If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels  
with letters or letter-number combinations. Please check with your local cable company. The following is a  
chart of common cable channel designations.  
CATV channel  
TV Display  
5A  
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10  
10  
11  
11  
12  
12  
13  
13  
A
B
14  
15  
CATV channel  
TV Display  
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
CATV channel  
TV Display  
R
S
T
U
V
W
W+1  
37  
W+2  
38  
W+3  
39  
W+4  
40  
W+5  
41  
W+6  
42  
W+7  
43  
W+8  
44  
W+9  
45  
31  
32  
33  
34  
35  
36  
CATV channel  
TV Display  
W+10 W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24  
46 47 48 49 50 51 52 53 54 55 56 57 58 59 60  
W+25 W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39  
61 62 63 64 65 66 67 68 69 70 71 72 73 74 75  
W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54  
CATV channel  
TV Display  
CATV channel  
TV Display  
76  
W+55 W+56 W+57 W+58  
91 92 93 94  
77  
78  
79  
80  
81  
82  
83  
84  
85  
W+59 W+60 W+61 W+62 W+63 W+64  
100 101 102 103 104 105  
86  
87  
88  
89  
90  
CATV channel  
TV Display  
A-5  
95  
A-4  
96  
A-3  
97  
A-2  
98  
A-1  
99  
CATV channel  
TV Display  
W+65 W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79  
106  
W+80 W+81 W+82 W+83 W+84  
121 122 123 124 125  
107  
108  
109  
110  
111  
112  
113  
114  
115  
116  
117  
118  
119  
120  
CATV channel  
TV Display  
- 33 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DVD SECTION  
ABOUT THE DISCS  
PLAYABLE DISCS  
Recorded  
Playable  
discs  
Disc size  
Region code  
Disc types  
Mark (logo)  
signals  
DVD-Video  
or  
* 1,2,4,6,10,11  
Example  
12 cm  
or  
8 cm  
Title 1  
Title 2  
DVD-RW  
DVD-R  
Digital video  
(MPEG2)  
Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1  
Chapter 2  
-
-
-
* 1,3,4,5,6  
7,9,10  
DVD+RW  
DVD+R  
* 1,3,4,5,6,8,9,10  
Audio CD  
* 4,6,10  
Audio CD  
Example  
12 cm  
or  
8 cm  
Digital audio  
Track 1  
Track 2  
Track 5  
Track 6  
Track 3  
Track 4  
CD-RW  
CD-R  
* 4,5,6,9,10  
is a trademark of DVD Format/Logo Licensing Corporation.  
If you cannot play back a disc which bears one of the marks above, check the following notes.  
*1: This unit conforms to the NTSC color system. Discs recorded in other color systems such as PAL cannot  
be played back.  
*2: Certain DVD-Video discs do not operate as described in this manual due to the intentions of the disc’s producers.  
*3: Discs recorded in the VR (Video Recording) format cannot be played back.  
*4: Scratched or stained discs may not be played back.  
*5: Some discs cannot be played back because of incompatible recording conditions, characteristics of the  
recorder or special properties of discs.  
*6: You can play back discs which bear the marks above. If you use nonstandardized discs, this unit may not  
play them back. Even if they are played back, the sound or video quality will be compromised.  
*7: You may play back the unfinalized DVD-R/RW disc recorded in the video format on our brand’s DVD  
recorder. However, depending on the recording status of a disc, the disc may not be played back at all or  
normally (the picture or sound may not be smooth, etc.). In this case, you need to finalize the disc with  
the DVD recorder. Refer to the manual accompanying the DVD recorder.  
*8: Only the discs recorded in the video format and finalized can be played back.  
Unfinalized discs cannot be played back. Depending on the recording status of a disc, the disc may not be  
played back at all or normally (the picture or sound may not be smooth, etc.).  
*9: If there is too much recording space left on a disc (the used portion is less than 55mm across), it may not  
play back properly.  
*10: Do not glue paper or put stickers on to the disc. These may damage the disc and the unit may not read it correctly.  
*11: The number inside the symbol refers to a region of the world and a disc encoded in a specific region for-  
mat can only be played back on unit with the same region code.  
UNPLAYABLE DISCS  
¡NEVER play back the following discs. Otherwise, malfunction may result!  
DVD-RAM / CD-I / Photo CD / Video CD / DVD with region codes other than 1 or ALL /  
DTS-CD / DVD-ROM for personal computers / CD-ROM for personal computers / MP3  
¡On the following disc, the sound MAY NOT be heard.  
Super Audio CD  
NOTE: Only the sound recorded on the normal CD layer can be delivered.  
The sound recorded on the high density Super Audio CD layer cannot be delivered.  
¡Any other discs without compatibility indications  
EN  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PLAYING A DISC  
BASIC PLAYBACK  
GENERAL FEATURES  
DVD-V CD  
DVD-V  
VD may contain menus to navigate the disc and  
D
Getting started  
access special features. Press the appropriate  
Number buttons or [K / L / s / B] to highlight  
your selection in the DVD main menu and press  
[ENTER] to confirm.  
¡Turn on the power of amplifier and any other com-  
ponents, if necessary.  
1
Press [POWER].  
¡The power will turn on.  
NOTES:  
¡Select DVD mode by pressing [SELECT], then  
2
3
Press [A OPEN/CLOSE] to open disc load-  
ing tray.  
operate the DVD functions.  
¡Unless stated, all operations described are based on  
remote control use. Some operations can be carried  
out using the menu bar on the TV screen.  
Place the chosen disc in the tray, with the  
label facing up.  
DISC MENU  
DVD-V  
1
Press [DISC MENU].  
¡The DVD main menu will appear.  
¡If the feature is not available, symbol may appear  
on the TV screen.  
¡If disc menu is available on the disc, audio language,  
subtitle options, chapters for the title and other  
options will appear for selection.  
4
Press [PLAY O].  
¡The tray will close automatically and playback will  
then start from the first chapter or track of the disc.  
¡Closing the disc tray manually or by pressing  
[A OPEN/CLOSE] also starts playback.  
¡If the playback does not start automatically, press  
[PLAY O].  
2
Press [K / L / s / B] to select an item and  
press [ENTER] to confirm selection.  
¡When you playback a DVD which features a title  
menu, it may appear on the screen. In this case,  
refer to “TITLE MENU” on this page.  
TITLE MENU  
5
Press [STOP C] to stop playback.  
DVD-V  
1
Press [TITLE].  
NOTES:  
¡The title menu will appear.  
¡If the feature is not available, symbol may  
appear on the TV screen.  
¡When the DVD mode has been switched to the  
TV/VCR mode, the DVD mode shuts down first and  
then the TV picture and sound appears in about 4  
seconds. Similarly, when [POWER] is pressed to  
turn off in the DVD mode, this mode shuts down  
first and then the unit is turned off.  
¡A “prohibited icon” may appear at  
the top-right on the TV screen  
during operation, warning that a  
2
Press [K / L / s / B] to select an item, and  
press [ENTER] to confirm selection.  
CALLING UP A MENU SCREEN  
DURING PLAYBACK  
prohibited operation has been  
encountered by the DVD or the  
disc.  
¡Press [DISC MENU] to call up the DVD menu.  
¡Press [TITLE] to call up the title menu.  
¡With DVDs that use titles for playback program  
signals, playback may start from the second title or  
it may skip these titles.  
¡During the playback of a two layered disc, pictures  
may stop for a moment. This happens when the 1st  
layer switches to the 2nd layer. This is not a mal-  
function.  
NOTE:  
¡Contents of menu and corresponding menu opera-  
tions may vary between discs. Refer to the manual  
accompanying the disc for details.  
EN  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SLOW FORWARD /  
SLOW REVERSE  
RESUME  
DVD-V  
CD  
DVD-V  
1
During playback, press [STOP C].  
¡Resume message will appear on the TV screen.  
1
2
During playback, press [PAUSE F].  
Press and hold [D] or [E] for a few sec-  
onds.  
2
Press [PLAY O], playback will resume from  
the point at which playback was stopped.  
¡“  
1” or “  
1” appears on the screen.  
¡To cancel resume, press [STOP C] twice.  
¡The resume information stays on even when the  
power is turned off.  
3
To select another speed, repeat step 2 until  
your required speed number appears on the  
screen.  
PAUSE  
¡Slow forward or reverse speed varies with the disc.  
Approximate speed is 1 (1/16), 2 (1/8) and 3 (1/2).  
DVD-V  
CD  
¡
When you press buttons on the main unit, use  
[SEARCH ].  
E
/
D
1
During playback, press [PAUSE F].  
¡Playback will pause and sound will be muted.  
4
To return to normal playback, press [PLAY O].  
2
To continue playback, press [PLAY O].  
ZOOM  
STEP BY STEP PLAYBACK  
DVD-V  
DVD-V  
The Zoom function allows you to enlarge the video  
image and to pan through the enlarged image.  
1
During playback, press [PAUSE F].  
¡Playback will pause and sound will be muted.  
1
Press [ZOOM] during playback.  
¡Playback will continue.  
2
3
The disc goes forward by one frame each  
time [PAUSE F] is pressed.  
2
Press [ZOOM] repeatedly to select the  
required zoom factor: ZOOM1, ZOOM2,  
ZOOM3 or OFF.  
To exit step by step playback, press [PLAY O].  
FAST FORWARD /  
FAST REVERSE  
3
4
Press [K / L / s / B] to move the zoomed  
picture across the screen.  
DVD-V  
CD  
To exit zoom mode, press [ZOOM] to OFF.  
NOTES:  
1
During playback, press and hold [D] or  
[E] for a few seconds.  
¡Zooming function does not work while disc menu is  
shown.  
¡D 1” or “E 1” appears on the screen.  
¡Zooming function is not available on some discs.  
¡It may take several seconds to slide the zoomed pic-  
ture.  
¡The picture may be distorted if you operate other  
functions repeatedly (ex. [PAUSE ] or [E], etc.)  
in the zoom mode.  
2
To select another speed, repeat step 1 until  
your required speed number appears on the  
screen.  
F
¡For DVDs, fast forward/reverse search speed is dif-  
ferent depending on the disc. Approximate speed is  
1 (×2), 2 (×8), 3 (×20), 4 (×50) and 5 (×100).  
¡For Audio CDs approximate speed is 1 (×2), 2 (×8)  
and 3 (×30).  
¡When you press buttons on the main unit, use  
[SEARCH E / D].  
3
To return to normal playback, press [PLAY O].  
EN  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SEARCH FUNCTION  
TRACK SEARCH  
TIME SEARCH  
CD  
DVD-V  
CD  
There are three ways to begin playback on an Audio  
CD at a specific track.  
1
2
During playback, press [SEARCH MODE]  
three times (CD: twice) to display the Time  
Search on the TV screen.  
Using the Number buttons  
Within 30 seconds, enter a desired disc  
time using the Number buttons.  
1
Press the Number buttons to enter the  
desired track number.  
¡Playback will start at the specified time.  
¡Press [CLEAR] to erase the incorrect input.  
¡When there is no need to enter a number, “0”  
¡Playback will start at the selected track.  
¡For single digit tracks (1-9), press a single number  
(eg. track 3, press [3]).  
appears automatically. For example, “ 0 : 0  
:
- - -  
¡To play track 26, press [+10], [2], [6].  
appears in the Time Search display if the total time  
of the track or title is less than 10 minutes.  
Using [SEARCH MODE]  
MARKER SETUP SCREEN  
1
Press [SEARCH MODE].  
¡The track search display appears.  
DVD-V  
CD  
2
Within 30 seconds, select the desired track  
number using the Number buttons.  
Use markers to memorize your favorite places on a disc.  
1
Press [SEARCH MODE] four times  
(CD: three times) during playback.  
¡For single digits press [0] first, if the total track of  
the disc is 10 tracks or more.  
¡Playback will start at the selected track.  
¡The display screen and Markers will appear on the  
TV screen.  
Using [H / G]  
2
3
Press [s / B] to select 1, 2, 3, 4, 5, 6, 7, 8, 9,  
During playback, press [G] to move the next track.  
Press it repeatedly to skip subsequent tracks. Press  
[H] to go back to beginning of the current track.  
Press it repeatedly to go to the previous tracks.  
¡If [H / G] is pressed while the playback is  
paused, the playback will be paused again after  
skipping to the next track.  
or 10 and ensure that “  
appears in the display.  
:
:
- - - - - - - -  
When you reach the desired point, press  
[ENTER].  
¡The Title or Track and elapsed playing time will  
appear in the TV screen.  
NOTE:  
¡[H / G] are not operative when playback is  
stopped.  
4
To return to the Marker later, press  
[SEARCH MODE] four times (CD: three  
times) during playback and press [s / B]  
to choose the desired marker, then press  
[ENTER].  
TITLE / CHAPTER SEARCH  
DVD-V  
1
Press [SEARCH MODE] once for the  
Chapter search, twice for the Title search  
NOTES:  
¡Operations which erase all Markers:  
– Opening the disc tray.  
during playback.  
_/2  
– Turning off the power.  
– Pressing [SELECT].  
– Selecting “AC” at step 2 and pressing [ENTER].  
¡To clear a marker:  
2
Enter the desired chapter/title number using  
the Number buttons.  
– Press [s / B] to select a cursor on to the marker  
number and press [CLEAR].  
¡You can mark up to 10 points.  
¡Playback will start at the selected chapter or title.  
¡Press [CLEAR] to erase the incorrect input.  
¡For single digits press [0] first, if the total number of  
chapter or title of the disc is 10 or more.  
5
Press [SEARCH MODE] or [RETURN] to exit.  
EN  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPECIAL PLAYBACK FUNCTION  
REPEAT  
PROGRAM  
CD  
You may determine the order in which tracks will play.  
REPEAT is available only during playback.  
REPEAT TITLE / CHAPTER  
DVD-V  
1
In the stop mode, press [MODE].  
¡The “PROGRAM” screen will appear.  
To activate the repeat function, press [REPEAT]  
during playback.  
2
Press [/ ] to select a track, then press  
¡The repeat mode changes as described below every  
time you press the button.  
[ENTER].  
¡Press [CLEAR] to erase the  
most recently entered track.  
¡If the entire Program cannot be  
displayed at once on a screen,  
G” appears to go to the next  
page and H” appears to go  
back to the previous page.  
TOTAL 1:03:30  
1
5
3:30  
5:10  
CHAPTER  
TITLE  
OFF  
(repeat off)  
10 4:20  
11 3:00  
12 3:20  
17 4:10  
22 2:50  
2/3  
(current chapter repeat) (current title repeat)  
1/4  
NOTES:  
¡Repeat Title/Chapter is not available with some  
scenes.  
¡The REPEAT setting will be cleared when moving  
to other title or chapter.  
3
Repeat step 2 until you have selected all the  
tracks you want to play in the program.  
4
Press [PLAY O] to play the programmed tracks.  
REPEAT TRACK  
NOTES:  
CD  
¡While the program is being played back, pressing  
[STOP C] works as follows.  
To activate the repeat function, press [REPEAT]  
during playback.  
¡Press [STOP C] once and then [PLAY O] again,  
playback will restart from the point where  
[STOP C] was pressed. (Program continued)  
¡Press [STOP C] twice and then [PLAY O] again,  
playback will restart from the track in the usual  
way. (Program canceled)  
¡The repeat mode changes as described below every  
time you press the button.  
TRACK  
ALL  
OFF  
(repeat off)  
(current track repeat)  
(entire disc repeat)  
¡Up to 99 tracks can be entered.  
¡To erase all tracks in the program at once, select  
“ALL CLEAR” at the bottom of the list at step 2.  
¡If you like to repeat the current track in the program,  
NOTES:  
press [REPEAT] several times until “  
TRACK”  
¡Repeat setting will be cleared when moving to other  
appears during playback. If you like to repeat the  
track.  
entire program press [REPEAT] several times until  
¡Repeat playback does not function during A-B  
repeat playback.  
ALL” appears during playback.  
A-B REPEAT  
RANDOM PLAYBACK  
DVD-V CD  
CD  
1
¡“  
Press [A-B] at your chosen starting point.  
This function shuffles the playing order of tracks  
A-” appears briefly on the TV screen.  
instead of playback in the sequence.  
1
In the stop mode, press [MODE] twice.  
2
¡“  
Press [A-B] again at your chosen end point.  
¡“RANDOM” screen appears.  
A-B” appears briefly on the TV screen, and  
RANDOM  
CD-DA  
TOTAL 0:45:55  
the repeat sequence begins.  
RANDOM PROGRAM  
no indication  
-
-
-
-
3
To exit the sequence, press [A-B].  
PLAY  
NOTES:  
¡The A-B repeat section can only be set within the cur-  
rent title (for DVDs) or current track (for Audio CDs).  
¡A-B repeat is not available with some scenes in DVD.  
¡To cancel the A point which was set, press  
[CLEAR].  
2
Press [PLAY O] to start random playback.  
NOTE:  
¡
If you like to repeat the current track in the random  
selection, press [REPEAT] several times until  
TRACK” appears during playback. If you like to  
¡A-B repeat playback does not function during title,  
chapter, track or all repeat playback.  
repeat the entire random selection press [REPEAT]  
several times until “  
back.  
ALL” appears during play-  
EN  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CHANGING THE SETTINGS  
SUBTITLE LANGUAGE  
AUDIO LANGUAGE  
DVD-V  
DVD-V  
The unit allows you to select a language during DVD  
disc (if multi languages are available) playback.  
The unit allows you to select a language for subtitles  
during DVD disc (if available) playback.  
1
Press [AUDIO] during playback.  
1
Press [SUBTITLE] during playback.  
1.ENG Dolby D 3/2.1ch 48k/3  
¡The subtitle language will  
appear on the display bar at  
the top of the TV screen.  
1.ENG/6  
2
Press [AUDIO] repeatedly to select your  
desired language.  
2
3
Press [SUBTITLE] repeatedly to select your  
desired subtitle language.  
NOTE:  
To turn off subtitles, press [SUBTITLE]  
repeatedly until “OFF” appears.  
¡Pressing [AUDIO] may not work on some DVDs  
with multiple audio languages (e.g. DVDs which  
allow audio language setting on the disc menu).  
NOTES:  
¡Pressing [SUBTITLE] may not work on some  
DVDs with multiple subtitle languages. In this  
case, set it on the disc menu. (Operation varies  
between discs. Refer to the manual of the disc.)  
¡If the desired language is not shown after pressing  
[SUBTITLE] several times, the disc does not have  
subtitles in that language.  
STEREO SOUND MODE  
CD  
1
Press [AUDIO] repeatedly during playback to  
select between “STEREO”, “L-ch” or “R-ch”.  
¡When “NOT AVAILABLE”  
NOT AVAILABLE  
appears on the TV screen, it  
STEREO  
means no subtitle is recorded  
on the scene.  
¡If you choose a language that has a 3 letter lan-  
guage code, the code will be displayed every time  
you change the Subtitle language setting. If you  
choose any other languages, “---” will be displayed  
instead. (Refer to page 42.)  
¡
STEREO - both right and left channels are active (stereo)  
L-ch - only left channel is active  
R-ch - only right channel is active  
EN  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CAMERA ANGLE  
VIRTUAL SURROUND  
DVD-V  
DVD-V  
CD  
Some DVD discs contain scenes which have been shot You can enjoy surround-sound effect over two speak-  
simultaneously from various angles. You can change ers on this unit.  
the camera angle when the “  
screen.  
” icon appears on the  
1
Press [MODE] twice (CD: once) during play-  
back.  
OFF  
1
Press [ANGLE] during playback.  
¡The selected angle will be displayed on the display  
bar at the top of the screen.  
1 / 8  
2
3
Press [ENTER] to set it “1” (Natural effect),  
“2” (Emphasized effect) or “OFF”.  
¡If the “ANGLE ICON” setting is “OFF” in the  
“OTHERS” menu, the “  
(Refer to page 44.)  
Press [RETURN] to exit.  
” icon will not appear.  
NOTE: (for CD play only)  
¡Virtual Surround will not be effective if the sound  
mode is set to something other than STEREO.  
2
Press [ANGLE] repeatedly to select your  
desired angle.  
BLACK LEVEL SETTING  
DVD-V  
Adjust the Black Level Settings to make the black  
parts of the picture brighter.  
1
Press [MODE] during playback.  
OFF  
2
Press [ENTER] to switch “ON”or “OFF”.  
ON: Makes the dark parts brighter.  
OFF: Shows the original picture as recorded.  
(Initial setting)  
3
Press [MODE] twice or [RETURN] to exit.  
NOTE:  
¡The setting will be saved even if the unit is turned  
off.  
EN  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
THE ON-SCREEN INFORMATION  
DVD-V  
CD  
You can check the information about the current disc by pressing [DISPLAY].  
For DVD-Vs  
For Audio CDs  
1
Press [DISPLAY] during playback to show  
current Chapter.  
1
Press [DISPLAY] during playback to show  
the current Track.  
¡The elapsed and remaining  
playing time of the current  
chapter will be displayed.  
¡The elapsed and remaining  
playing time of the current  
track will be displayed.  
4/12 0:03:21 - 0:02:15  
T
9/49  
0:00:00 -0:03:30  
2
Press [DISPLAY] again to show current Title.  
2
Press [DISPLAY] again to show current Total  
Track.  
¡The elapsed and remaining  
playing time of the current  
title will be displayed.  
1/3 0:00:00 - 1:23:45  
¡The elapsed and remaining  
playing time of the total track  
will be displayed.  
4/12 0:13:45 - 0:45:40  
T
3
Press [DISPLAY] again.  
3
Press [DISPLAY] again to exit.  
¡The bit rate and the current  
repeat setting will be dis-  
played.  
¡If you are playing a dual layered disc, the layer  
number will also be displayed.  
T
L1  
NOTE:  
¡When you are playing a disc in PROGRAM or  
RANDOM mode, “ PROGRAM” (or RANDOM)  
(L0: Layer 0 is playing. L1: Layer 1 is playing)  
will be displayed at step 2.  
PROGRAM  
B
4
Press [DISPLAY] again to exit.  
EN  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CHANGING THE DVD SET UP ITEMS  
Language  
Code Language  
Code  
CUSTOM MENU  
A-B  
L-N  
Abkhazian  
Afar  
4748 Laothian  
4747 Latin  
5861  
5847  
5868  
5860  
5866  
5957  
5953  
5965  
5958  
5966  
5955  
5964  
5961  
5960  
6047  
6051  
6061  
DVD-V Afrikaans  
Amharic  
4752 Latvian;Lettish  
6563 Lingala  
4759 Lithuanian  
4764 Macedonian  
5471 Malagasy  
4765 Malay  
Albanian  
You can change the DVD player’s settings.  
Arabic  
1
Press [SETUP] twice in the stop mode so  
that the DVD SETUP menu appears.  
Armenian  
Assamese  
Aymara  
4771 Malayalam  
4772 Maltese  
4847 Maori  
Azerbaijani  
Bashkir  
Basque  
¡Press [L] to select “CUSTOM”  
then press [ENTER].  
SETUP  
QUICK  
CUSTOM  
INITIALIZE  
5167 Marathi  
Bengali;Bangla  
Bhutani  
Bihari  
4860 Moldavian  
5072 Mongolian  
4854 Nauru  
NOTE:  
¡If the menu does not appear, press [PLAY O] first,  
then press [STOP C]. Make sure the disc is in the  
stop mode, then slowly press [SETUP] twice.  
Bislama  
4855 Nepali  
Breton  
4864 Norwegian [NOR]  
O-R  
Bulgarian  
Burmese  
Byelorussian  
4853  
5971 Occitan  
4851 Oriya  
6149  
6164  
6159  
6247  
6265  
5247  
6258  
6266  
6367  
6459  
6461  
6467  
C-E  
Oromo(Afan)  
5759 Panjabi  
4947 Pashto;Pushto  
7254 Persian  
4961 Polish  
5464 Portuguese [POR]  
4965 Quechua  
2
Select the desired item.  
Cambodian  
Catalan  
¡Press [K / L] to select the desired item then press  
[ENTER] to confirm.  
Chinese [CHI]  
Corsican  
Croatian  
Refer to the pages below to set up each item.  
Czech  
Danish [DAN]  
Dutch [DUT]  
English [ENG]  
Esperanto  
Estonian  
5047 Rhaeto-Romance  
6058 Romanian [RUM]  
5160 Russian [RUS]  
SETUP  
CUSTOM  
A
P 42 Step  
3
3
3
3
3
LANGUAGE  
DISPLAY  
AUDIO  
PARENTAL  
OTHERS  
B
P 43 Step  
5161  
S
C
P 43 Step  
5166 Samoan  
Sangho  
5261 Sanskrit  
5256 Scots Gaelic  
5255 Serbian  
6559  
6553  
6547  
5350  
6564  
6554  
6566  
6660  
6560  
6550  
6555  
6565  
6557  
6558  
6561  
5165  
6567  
6569  
6568  
F-H  
D
P 44 Step  
Faroese  
Fiji  
E
P 44 Step  
Finnish [FIN]  
French [FRE]  
Frisian  
5264 Serbo-Croatian  
5271 Sesotho  
5358 Setswana  
5747 Shona  
A
LANGUAGE SETTING  
Galician  
Follow steps to in the “CUSTOM MENU” section  
1
2
Georgian  
German [GER]  
Greek [GRE]  
Greenlandic  
Guarani  
above.  
5051 Sindhi  
5158 Singhalese  
5758 Siswat  
5360 Slovak  
3
Press [K / L] to select the desired item then  
press [ENTER].  
Gujarati  
Hausa  
Hebrew  
5367 Slovenian  
5447 Somali  
5569 Spanish [SPA]  
5455 Sundanese  
5467 Swahili  
SETUP  
LANGUAGE  
AUDIO:  
AUDIO  
SUBTITLE  
DISC MENU  
ORIGINAL  
OFF  
ENGLISH  
Sets the audio language.  
Hindi  
Hungarian [HUN]  
I-K  
Icelandic [ICE]  
Indonesian  
Interlingua  
Interlingue  
Inupiak  
SUBTITLE:  
Swedish [SWE]  
Sets the subtitle language.  
DISC MENU:  
5565  
5560 Tagalog  
5547 Tajik  
5551 Tamil  
5557 Tatar  
5347 Telugu  
5566 Thai  
T
6658  
6653  
6647  
6666  
6651  
6654  
4861  
6655  
6661  
6665  
6664  
6657  
6669  
Sets the language for DVD menu.  
Irish [IRI]  
Italian [ITA]  
Japanese [JPN]  
Javanese  
Kannada  
Kashmiri  
4
Press [K / L] to select a setting then press  
[ENTER].  
SETUP  
LANGUAGE  
LANGUAGE  
LANGUAGE  
5647 Tibetan  
5669 Tigrinya  
5760 Tonga  
5765 Tsonga  
5757 Turkish [TUR]  
6469 Turkmen  
5771 Twi  
AUDIO  
¡If “OTHER” is selected on the  
“AUDIO”, “SUBTITLE” or  
“DISC MENU” screen, press  
four-digit number to enter the  
code for the desired language.  
(Refer to the language code  
list.)  
ORIGINAL  
ENGLISH  
FRENCH  
Kazakh  
Kinyarwanda  
Kirghiz  
Kirundi  
SETUP  
6460  
U-Z  
SUBTITLE  
OFF  
ENGLISH  
FRENCH  
Korean [KOR]  
Kurdish  
5761 Ukrainian  
5767 Urdu  
Uzbek  
6757  
6764  
6772  
6855  
6861  
4971  
6961  
7054  
5655  
7161  
7267  
Vietnamese  
Volapuk  
Welsh  
Wolof  
Xhosa  
Yiddish  
¡Only the languages supported  
by the disc can be selected.  
SETUP  
DISC MENU  
ENGLISH  
FRENCH  
SPANISH  
Yoruba  
Zulu  
5
Press [SETUP] to exit the menu.  
If you choose a language that has a 3 letter language  
code, the code will be displayed every time you change  
the AUDIO or SUBTITLE language setting above. If  
you choose any other languages, ‘---’ will be displayed  
instead. (3 letter language code is written in bracket.)  
NOTES:  
¡Language Setting for Audio and Subtitle are not  
valid for some discs due to default setting of the  
disc. In this case, set them by pressing [AUDIO] and  
[SUBTITLE]. (Refer to page 39.)  
¡If you select a language that is not supported by the  
disc, subtitle will automatically be set OFF and the  
first item of the audio languages will be automatically  
set.  
EN  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
B
C
DISPLAY SETTING  
AUDIO SETTING  
Choose the appropriate Audio settings for your equip-  
ment as it only affects during the playback of DVD  
discs.  
Follow steps to in the “CUSTOM MENU” section  
on page 42.  
1
2
3
Press [K / L] to select the below items then  
press [ENTER].  
Follow steps to in the “CUSTOM MENU” section  
on page 42.  
1
2
TV MODE:  
QUICK  
3
Press [K / L] to select the below items then  
press [ENTER].  
You can change certain aspects of the DVD display  
screens and on-screen messages on the TV screen.  
SETUP  
DRC  
DOWN SAMPLING  
DOLBY DIGITAL  
AUDIO  
DRC (Dynamic Range  
Control):  
¡To compress the range of  
soft to loud sound.  
¡4:3 LETTER BOX (default):  
To show black bars on top  
and bottom of the screen.  
SETUP  
DISPLAY  
ON  
ON  
BITSTREAM  
TV MODE  
STILL MODE  
4:3 LETTER BOX  
AUTO  
¡4:3 PAN & SCAN: To show  
a full height picture with both sides trimmed.  
¡The default setting is “ON”.  
SETUP  
AUDIO  
DOWN SAMPLING:  
¡ON : Output in 48 kHz.  
(default)  
DRC  
DOWN SAMPLING  
DOLBY DIGITAL  
ON  
ON  
BITSTREAM  
STILL MODE  
This function allows you to adjust picture resolution  
and quality in the still mode.  
:
¡OFF : Output the original  
sound.  
SETUP  
DISPLAY  
¡AUTO (default):  
When playing disc with copyright Protection  
¡If you select “OFF”, copyright protection will be  
activated and sound will be down sampled at 48kHz.  
Automatically select the best  
resolution setting (FRAME  
or FIELD) based on the data  
characteristics of the pictures.  
¡FIELD: Select “FIELD” when the pictures are still  
unstable even if “AUTO” is selected.  
FIELD stabilizes the pictures, although the picture  
quality may become coarse due to the limited  
amount of data.  
TV MODE  
STILL MODE  
4:3 LETTER BOX  
AUTO  
SETUP  
DRC  
DOWN SAMPLING  
DOLBY DIGITAL  
AUDIO  
DOLBY DIGITAL:  
QUICK  
ON  
ON  
BITSTREAM  
Set to “BITSTREAM” when  
the unit is connected to a  
Dolby Digital Decoder.  
¡BITSTREAM: Output a Dolby Digital signal  
¡FRAME: Select “FRAME” to display relatively  
motionless pictures in higher resolution.  
FRAME improves the picture quality, although it  
may unstabilizethe pictures due to simultaneous  
output of two field data.  
(default)  
¡PCM: Convert the Dolby Digital to PCM  
(2 channel stereo)  
4
Press [SETUP] to exit the menu.  
4
Press [SETUP] to exit the menu.  
QUICK MENU  
¡You can select the “TV MODE” or “DOLBY DIGITAL” from the QUICK menu quickly. To access the  
QUICK menu, select “QUICK” instead of “CUSTOM” at step on page 42.  
1
LANGUAGE SETTING FOR THE ON-SCREEN MENUS  
¡You can access the TV/VCR SETUP menu by pressing [SETUP] from the DVD mode. Refer to  
“MENU LANGUAGE” on page 21 to change the language for the on-screen menus.  
EN  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
D
PARENTAL CONTROL  
IF YOU FORGET THE PASSWORD  
Parental Control limits the disc viewing that exceed  
your setting (with a password or playback will stop).  
This feature allows you to prevent discs with alterna-  
tive scenes from being played by your children.  
1
Press the Number buttons [4], [7], [3], [7] at  
step 3. Then enter your new password.  
¡Password will be cleared and parental level will be  
set to “ALL”.  
PARENTAL LEVEL  
2
Proceed with steps 4 to 6 again.  
Parental Level allows you to set the rating level of  
your DVD discs. Playback will stop if the disc’s rat-  
ings exceed the level you set.  
E
OTHER SETTINGS  
Follow steps to in the “CUSTOM MENU” section  
on page 42.  
1
2
Follow steps to in the “CUSTOM MENU” section  
1
2
on page 42.  
3
Press [K / L] to select the below items,  
3
Enter your four-digit password then press  
[ENTER].  
then press [ENTER].  
SETUP  
OTHERS  
SETUP  
PARENTAL  
PASSWORD  
ANGLE ICON  
ON  
Enter current password.  
AUTO POWER OFF ON  
ANGLE ICON:  
¡Press [ENTER] repeatedly to turn Angle icon  
4
Press [K / L] to select “PARENTAL LEVEL”  
“ON” or “OFF”.  
then press [ENTER].  
SETUP  
PARENTAL  
¡The default setting is “ON”.  
PARENTAL LEVEL  
PASSWORD CHANGE  
ALL  
AUTO POWER OFF:  
¡Press [ENTER] repeatedly to turn Auto Power off  
“ON” or “OFF”.  
¡
The default setting is “ON” and the screen saver pro-  
gram starts when there is no input from the unit for 5  
minutes in the stop mode. After the screen saver pro-  
gram is activated for 15 minutes, the power is auto-  
matically turned off.  
5
6
Press [K / L] to select the desired level  
then press [ENTER].  
SETUP  
PARENTAL  
PARENTAL LEVEL  
ALL  
8
7 [NC-17]  
6 [R]  
4
Press [SETUP] to exit the menu.  
Press [SETUP] to exit the menu.  
NOTES:  
¡
When doing this for the first time, enter any 4 digits.  
(except for 4737) That number will be used as the pass-  
word. (in the event you forget the password, see below)  
INITIALIZE  
DVD-V  
¡To change the password, press [K / L] to select  
PASSWORD CHANGE” at step 4 then press  
[ENTER]. Enter the four-digit password, then  
press [ENTER].  
This allows you to return all selections of SETUP  
(except for “PARENTAL” and menu language) to  
their default settings.  
¡With some DVDs, it may be difficult to find if they  
are compatible with parental lock. Be sure to check  
if the parental lock function operates in the way that  
you have set.  
1
2
Press [SETUP] twice in the stop mode so  
that the “INITIALIZE” menu appears.  
Press [K / L] to select “INITIALIZE” then  
¡Record the password in case you forget it.  
press [ENTER].  
SETUP  
CONTROL LEVELS  
QUICK  
CUSTOM  
INITIALIZE  
¡
ALL  
All parental lock is cancelled.  
¡
Level 8  
DVD software of any grade (adult/general/children)  
can be played back.  
3
Press [K / L] to select “YES” then press  
[ENTER] twice.  
¡
Levels 7 to 2  
SETUP  
INITIALIZE  
All the settings (except for  
PARENTAL” and menu  
language) will be cleared.  
¡To cancel the initialization,  
select “NO”.  
Only DVD software intended for general use and  
children can be played back.  
Initialize?  
NO  
YES  
¡
Level 1  
Only DVD software intended for children can be  
played back, with those intended for adult and  
general use prohibited.  
4
Press [SETUP] to exit the menu.  
EN  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING GUIDE  
If the unit does not perform properly when operated as instructed in this Owner’s Manual, check the unit, con-  
sulting the following checklist.  
PROBLEM  
CORRECTIVE ACTION  
Make sure the power plug is connected to an AC outlet.  
Make sure the power is turned on.  
Check if the power plug is connected to an AC outlet.  
Check the batteries in the remote control.  
Aim the remote control directly at the remote sensor. If necessary,  
remove all the obstacles between the sensor and the remote control.  
You have to be within 23 feet of the unit.  
Check if the correct mode is selected. If not switch the mode by  
pressing [SELECT], whichever you need.  
No power  
No operation by infrared remote  
control  
TV/VCR Mode  
Sometimes a performance problem can be easily solved by checking seemingly apparent but often overlooked  
possibilities. Before arranging for service, check these items. It could save your time and money.  
PROBLEM  
No picture or sound  
CORRECTIVE ACTION  
Make sure the AC cord is connected to an AC outlet.  
Check antenna connection.  
Press [SELECT] to select TV mode.  
Then try other TV feature.  
Let the unit program its tuner memory.  
Adjust direction or replace antenna.  
Adjust picture controls.  
Check for broken pin of the antenna cable.  
Adjust volume control on remote control or main unit.  
Press [MUTE] to restore sound.  
No picture or poor picture on the  
unit  
No sound or poor sound  
Bars On Screen  
If outside antenna is being used, check for broken wire.  
Check for local interference.  
Picture Distorted or Blurred  
Try a new channel, if OK, then possible station trouble.  
If outside antenna is being used, check for broken wire.  
Try a new channel, if OK, then possible station trouble.  
If outside antenna is being used, check for broken wire.  
Check for local interference.  
Try a new channel, if OK, then possible station trouble.  
Is antenna connected to jack on the back of the set?  
If outside antenna is being used, check for broken wire.  
Adjust “COLOR” control.  
Try a new channel, if OK, then possible station trouble.  
Is antenna connected to jack on the back of the set?  
If outside antenna is being used, check for broken wire.  
Check for local interference.  
Try a new channel, if OK, then possible station trouble.  
Is antenna connected to jack on the back of the set?  
If outside antenna is being used, check for broken wire.  
Adjust “CONTRAST” & “BRIGHT” control.  
Try a new channel, if OK, then possible station trouble.  
Is antenna connected to jack on the back of the set?  
If outside antenna is being used, check for broken wire.  
Check for local interference.  
Picture Rolls Vertically  
Lines or Streaks in Picture  
No Color  
Poor Reception on Some Channels  
Ghosts in Picture  
Weak Picture  
Sound OK, Picture Poor  
Adjust “CONTRAST” & “BRIGHT” control.  
EN  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PROBLEM  
Picture OK, Sound Poor  
CORRECTIVE ACTION  
Try a new channel, if OK, then possible station trouble.  
Check for local interference.  
Make sure the timer recording is set correctly.  
Make sure the power is off.  
Make sure the unit’s clock is set correctly.  
Make sure the tape has an erase-prevention tab. If need, cover the  
hole with plastic tape.  
Adjust tracking control for a better picture using [CHANNEL K / L]  
on the unit.  
Head cleaning may be necessary. Refer to “AUTO HEAD  
CLEANING” on page 48.  
Make sure the AC cord is connected to an AC outlet.  
Check batteries in remote control.  
You can not copy a copyrighted video tape. You are experiencing  
Timer recording is not possible  
Cannot go into Record mode  
Playback picture is partially noisy  
No picture but the audio is OK in  
playback  
No operation by infrared Remote  
Control  
Video or color fades in and out  
when making a copy of a video tape  
copy guard protection.  
Magnetism from nearby appliances and geomagnetism might affect  
the color of the TV picture. Move the unit away from the appliances,  
the unit can repair itself automatically. If you want to repair immedi-  
ately, unplug the power cord, then plug it in again 30 minutes later  
or so. This automatically resets the unit.  
Different color marks on screen  
CLOSED CAPTION PROBLEM  
POSSIBLE REMEDY  
Misspelling in captions  
Error committed by the closed captioning production company.  
Possible in a live broadcast. Not in case of a prerecorded program.  
Text is not shown in its entirety or  
a delay occurs from what is being  
said.  
A few seconds of delay is common for live broadcast.  
Display capacity may not exceed 220 words per minute. If a dialogue  
exceeds that rate, selective editing is used to insure that the captions  
remain up-to-date with the current TV screen dialogue.  
Captions scrambled with white  
boxes  
Caused by interferences of building, power lines, thunderstorms, etc.  
No captions in a program which  
must contain closed caption  
The broadcast may use a time compression process to speed up the  
program. The decoder cannot read the compressed information and  
captions will be lost.  
No captions in a prerecorded  
videotape which indicated closed  
captions included.  
Possibility of a illegal copy or an erroneous copying process  
accidentally performed by the fabricator.  
Black box in the TV screen  
You are in TEXT mode. Select a CAPTION mode (“C1”, “C2”) or  
Caption “OFF”.  
EN  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DVD Mode  
PROBLEM  
CORRECTIVE ACTION  
Insert a correct video disc that plays on this unit.  
Press [SELECT] to select DVD mode, then try other DVD feature.  
Insert the disc.  
No picture  
Disc cannot be played  
Clean the disc.  
Place the disc correctly, with the label side up.  
Cancel the parental lock or change the control level.  
Connect the audio cables firmly.  
Turn the power of the audio component on.  
Correct the audio output settings.  
Correct the input settings on the audio component.  
This unit does not support DTS audio. This is not a malfunction.  
There are some cases where pictures may be slightly distorted,  
which are not a sign of a malfunction.  
No sound  
No DTS audio is output  
Distorted picture  
Although pictures may stop for a moment, this is not a malfunction.  
The selected language is not available for audio or subtitles on the  
DVD. (This is not a malfunction.)  
Audio or subtitle language  
does not match the set up  
The camera angle cannot be changed The DVD does not contain sequences recorded from different cam-  
era angles. (This is not a malfunction.)  
Audio or subtitle language cannot be The DVD does not contain audio source or subtitles in the selected  
changed  
language. (This is not a malfunction.)  
“Prohibited icon” appears on the  
screen, prohibiting an operation  
CD sound dropout  
No CD reproduction  
DVD picture dropout  
DVD picture freeze  
That operation is prohibited by the unit or the disc.  
(This is not a malfunction.)  
Scratched disc. Replace the disc with an unscratched one.  
DVD picture in mosaic  
No DVD reproduction  
NOTES:  
Some functions are not available in specific modes, but this is not a malfunction. Read the description in  
this Owner’s Manual for details on correct operations.  
Playback from a desired track and random playback are not available during program playback.  
EN  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
1.Please visit your local Audio/Video store and pur-  
CABINET CLEANING  
chase a good quality VHS Video Head Cleaner.  
2.If a Video Head Cleaner does not solve the prob-  
lem, please call our help line mentioned on the  
front page, to locate an Authorized Service Center.  
NOTES:  
Wipe the front panel and other exterior surfaces of  
the unit with a soft cloth immersed in lukewarm  
water and wrung dry.  
Never use a solvent or alcohol. Do not spray insec-  
ticide liquid near the unit. Such chemicals may  
cause damage and discoloration to the exposed sur-  
faces.  
Remember to read the instructions included with  
the video head cleaner before use.  
Clean video heads only when problems occur.  
AUTO HEAD CLEANING  
SERVICING  
Automatically cleans video heads as you insert or  
remove a cassette, so you can see a clearer picture.  
Should your unit become inoperative, do not try to  
correct the problem by yourself. There are no user-  
serviceable parts inside. Turn off, unplug the power  
cord and please call our help line mentioned on  
the front page, to locate an Authorized Service  
Center.  
Playback picture may become blurred or interrupt-  
ed while the TV program reception is clear. Dirt  
accumulated on the video heads after long periods  
of use or the usage of rental or worn tapes can  
cause this problem.  
If a streaky or snowy picture appears during play-  
back, the video heads in your unit may need to be  
cleaned.  
IF THE LASER OPTICAL PICKUP UNIT IS DIRTY  
If the unit still does not perform properly when it is operated, while referring to the relevant sections and to  
“TROUBLESHOOTING GUIDE” in this Owner’s Manual, the laser optical pickup unit may be dirty.  
Consult your dealer or an Authorized Service Center for inspection and cleaning of the laser optical pickup  
unit.  
DISC HANDLING  
Handle the discs so that fingerprints and dust do  
not adhere to the surfaces of the discs.  
To clean-off, use a soft cloth.  
Do not use a hard cloth since this will mar the disc.  
Wipe the disc in a straight line from center to edge.  
Never wipe with a circular motion.  
Do not use detergent or abrasive cleaning agents.  
Always store the disc in its protective case when it  
is not used.  
EN  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPECIFICATIONS  
GENERAL SPECIFICATIONS  
ELECTRICAL SPECIFICATIONS  
Sound output:  
2 speakers, 1W, 8 ohm  
TV/VCR  
CRT:  
19 inch in-line gun,  
90˚ deflection tube  
NTSC-M  
OTHER SPECIFICATIONS  
Terminals  
Television system:  
Closed caption system :§15.119/FCC  
Antenna input:  
VHF/UHF/CATV  
75 ohm unbalanced (F-type)  
RCA connector [ 1  
RCA connector [ 2  
Video Heads:  
Tape width:  
Tape speed  
SP:  
LP:  
SLP:  
Tuner channel  
TV VHF Low:  
TV VHF High:  
TV UHF:  
CATV  
Rotary four-head  
1/2 inch  
Video input:  
Audio L/R input:  
Headphone:  
Coaxial digital  
audio output:  
1/8" stereo (3.5mm)  
33.40mm/sec.  
16.67mm/sec.  
11.12mm/sec.  
One pin jack,  
500m Vpp (75 ohm)  
Digital encoded  
Remote control:  
#2~#6  
#7~#13  
#14~#69  
infrared light system  
Operating  
temperature:  
5˚C to 40˚C  
(41˚F~104˚F)  
Power requirements: AC 120V, 60Hz  
Power consumption  
VHF:  
5A  
MID band:  
SUPER band:  
HYPER band:  
A5~A1, A~I  
J~W  
W+1~W+84  
(Maximum):  
Picture tube:  
Dimensions:  
90W  
19"  
H :19-11/16"(500mm)  
W:21-7/8" (556mm)  
D :18-3/4" (477mm)  
45.2 lbs. (20.5kg)  
Weight:  
DVD  
Product type:  
Discs:  
DVD Player  
DVD video, Audio CD  
Output signal format: NTSC color  
Designs and specifications are subject to change without notice.  
If there is a discrepancy between languages, the default language will be English.  
EN  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12. Indicador de grabación  
INDICE  
Parpadea durante la grabación. Se ilumina durante el  
modo de espera de grabación controlada por  
temporizador.  
INDICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50  
CONTROLES DE OPERACIÓN Y FUNCIONES . . . . . 50  
PARA INSERTAR LAS PILAS . . . . . . . . . . . . . . . . . . . . 51  
PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 51  
CONEXIONES DE ANTENA/CABLE . . . . . . . . . . . . . . 51  
CONEXIÓN A TOMAS DE ENTRADA DELANTERAS 52  
CONEXIÓN A UN AMPLIFICADOR ESTÉREO  
13. Botón I REC/OTR (Panel frontal)  
Presione para empezar la grabación manual. Presione  
repetidamente para empezar la grabación instantánea (OTR).  
Botón RECORD (Mando a distancia)  
Presione para empezar la grabación manual.  
EQUIPADO CON TOMAS DE ENTRADA DIGITAL.  
(para DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52  
CONEXIÓN A UN DECODIFICADOR DOLBY DIGITAL  
(para DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52  
14. Botón E REW (para TV/VCR)  
Presione para rebobinar la cinta o para ver la imagen  
rápidamente en dirección de retroceso durante el modo  
de reproducción. (Búsqueda en dirección de retroceso)  
SECCIÓN DE TV/VCR  
15. Botón F.FWD D (para TV/VCR)  
FUNCIONES Y AJUSTES DE TV. . . . . . . . . . . . . . . . . 53  
PARA MIRAR UN PROGRAMA DE TV . . . . . . . . . . . . 53  
IDIOMA DEL MENÚ . . . . . . . . . . . . . . . . . . . . . . . . . . . 53  
AJUSTE DEL RELOJ . . . . . . . . . . . . . . . . . . . . . . . . . . . 53  
GRABACIÓN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54  
GRABACIÓN NORMAL . . . . . . . . . . . . . . . . . . . . . . . . 54  
Presione para adelantar rápidamente la cinta o para ver la  
imagen rápidamente en dirección de avance durante el modo  
de reproducción. (Búsqueda en dirección de avance)  
16. Botón  
C
A STOP/EJECT  
Presione para detener la cinta. Presione en el modo de  
parada para retirar la cinta de la unidad.  
SECCIÓN DE DVD  
17. Ventanilla del sensor de mando a distancia  
REPRODUCCIÓN BÁSICA . . . . . . . . . . . . . . . . . . . . . . 55  
MENÚ DE DISCO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55  
REANUDACIÓN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55  
18. Toma HEADPHONE  
Para conectar auriculares (no suministrados) y escuchar  
en privado.  
CONTROLES DE  
19. Toma de entrada VIDEO  
OPERACIÓN Y FUNCIONES  
Conecte aquí la toma de salida de video de una  
videocámara o de una videograbadora.  
20. Tomas de entrada AUDIO L/R  
Conecte aquí las tomas de salida de audio de una  
videocámara o de una videograbadora.  
• Consulte la figura 1 de la página 9 para el  
panel frontal de la unidad  
• Consulte la figura 2 de la página 9 para el  
mando a distancia  
21. Compartimiento del cassette  
• Consulte la figura 3 de la página 10 para la  
vista posterior  
22. Botón PICTURE  
Presione para ajustar la imagen.  
23. Botones numéricos  
1. Botón POWER  
Presione para encender y apagar la unidad.  
Modo TV/VCR:  
Presione dos cifras para acceder directamente al canal  
deseado.  
K
L
2. Botones VOLUME (VOL.)  
/
Presione para controlar el nivel de volumen del DVD y  
el televisor.  
No olvide presionar [0] antes de elegir un canal de una  
sola cifra.  
Botón +100  
Presione para seleccionar canales de televisión por  
cable cuyo número sea superior a 99.  
Modo DVD:  
Presione para introducir el número deseado.  
Botón +10  
Presione para introducir números superiors a 9.  
3. Botones SKIP H / G (para DVD)  
Presione una vez para omitir capítulos o pistas y  
desplazarse a un punto específico.  
Botones SEARCH E / D (para DVD)  
Mantenga el botón presionado para cambiar la  
velocidad de reproducción en avance o retroceso.  
4. Botón B PLAY  
Inicia la reproducción del contenido del disco o cinta.  
5. Botón C STOP  
(Panel frontal) Detiene la operación del disco.  
(Mando a distancia) Detiene la operación del disco o el  
casete.  
6. Botón A OPEN/CLOSE  
Presione para insertar un disco en la bandeja o retirarlo  
de ella.  
24. Botón PAUSE  
F
Hace una pausa en la reproducción del disco o cinta.  
25. Botón SPEED  
Presione para seleccionar la velocidad de grabación  
deseada: SP/SLP.  
26. Botón C.RESET  
Presione para poner el contador en 0:00:00.  
Presione también para cancelar un ajuste de programa  
de temporizador.  
7. Bandeja de carga del disco  
8. Indicador DVD  
27. Botón DISPLAY  
Se ilumina durante el modo DVD.  
Modo TV/VCR:  
9. Botón SELECT  
Indica el contador o el número del canal y la fecha  
actual en la pantalla del televisor.  
Modo DVD:  
Presione para cambiar al modo TV/VCR, modo de  
entrada externa o modo de DVD. El modo  
seleccionado (TV/VCR o DVD) se visualiza en el  
indicador del panel delantero.  
Indica el estado actual en la pantalla del televisor.  
28. Botón SETUP  
10. Indicador TV/VCR  
Presione para entrar o salir del menú de configración  
de televisor o DVD.  
Se ilumina durante el modo TV/VCR.  
K
L
11. Botones CHANNEL (CH.)  
/
29. Botón TITLE  
Utilice para seleccionar canales memorizados.  
Para visualizar el menú de títulos.  
ES  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
30. Botón CLEAR  
PARA INSERTAR LAS PILAS  
Presione para cancelar o borrar un ajuste entrado actualmente.  
31. Botón MODE  
1) Abra la cubierta del compartimiento de las pilas  
empujando la cubierta del mando a  
distancia en el sentido de la flecha.  
2) Inserte 2 pilas “AA” en el  
Presione para llamar la pantalla de la reproducción  
programada o la de reproducción aleatoria en el modo  
de parada.  
Presione para llamar la pantalla de ajuste del nivel del  
negro o la pantalla de sonido ambiental durante la  
reproducción.  
compartimiento de las pilas, en el  
sentido indicado por las marcas de polaridad (+/-).  
3) Vuelva a poner la cubierta.  
32. Botón SEARCH MODE  
Presione para localizar un punto deseado.  
33. Botón AUDIO (modo DVD)  
Presione para seleccionar un modo de sonido o idioma  
de audio deseado.  
PREPARACIÓN PARA LA  
UTILIZACIÓN  
34. Botón SUBTITLE  
Presione para seleccionar el idioma de subtítulos  
deseado.  
35. Botón REPEAT  
CONEXIONES DE ANTENA/CABLE  
Repite la reproducción del disco, título, capítulo o pista  
actual.  
Consulte la figura 4 de la página 12  
36. Botón ANGLE  
Presione para cambiar el ángulo de la cámara y ver la  
secuencia que se está reproduciendo desde un ángulo  
diferente (si existe).  
Nota para el instalador de sistemas CATV  
Esta nota tiene la finalidad de llamar la atención  
del instalador de sistemas CATV para que tenga  
en cuenta el Artículo 820-40 de la NEC, que  
proporciona recomendaciones para hacer una  
conexión a tierra apropiada y, en particular,  
especifica que la tierra del cable debe conectarse  
al sistema de puesta a tierra del edificio, tan cerca  
del punto de entrada del cable como sea posible.  
37. Botón A-B (modo DVD)  
Repite la reproducción de una sección seleccionada.  
38. Botón RETURN  
Permite volver a la pantalla anterior en el menú de  
configuración.  
39. Botón ENTER  
Presione para establecer un ajuste.  
K
L
40. Botones  
/
/
{ /  
B
Modo TV/VCR:  
Presione para seleccionar un modo de ajuste en el  
menú que aparece en la pantalla del televisor.  
Presione también para seleccionar o establecer ajustes  
en un menú en particular.  
NOTA:  
Antes de enchufar la antena a la toma ANT. de la  
unidad, compruebe que la clavija no esté doblada.  
Si esta doblada, póngala derecha como se muestra  
en la ilustración, y luego conéctela en la toma  
ANT. de la unidad.  
Modo DVD:  
Presione para seleccionar un ítem de menú.  
41. Botón DISC MENU  
Muestra menú del DVD.  
42. Botón ZOOM  
Clavija doblada  
Amplía parte de la imagen reproducida de un DVD.  
43. Botón MUTE  
Cable  
Suprime la salida de sonido. Presione de nuevo para  
restablecer el sonido.  
Clavija  
(Necesita enderezarse)  
(Clavija derecha)  
44. Botón SLEEP  
Utilice para ajustar el temporizador de dormir.  
NOTA:  
45. Toma ANT.  
Para su seguridad y para evitar que se dañe  
la unidad, desenchufe el cable de antena de la  
toma ANT. antes de mover la unidad.  
Conecte a una antena, sistema de televisión por cable o  
sistema de satélite.  
46. Cable de alimentación  
Conecte a un toma de CA estándar (120 V, /60 Hz).  
NOTA:  
Antes de conectar el cable de alimentación de una  
toma de CA estándar, retírelo del gancho para evitar  
dañarlo.  
47. Toma AUDIO OUT COAXIAL  
Conecte solamente a la entrada digital de un  
amplificador externo o decodificador (para audio de  
DVD solamente).  
ES  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONEXIÓN A TOMAS DE  
ENTRADA DELANTERAS  
CONEXIÓN A UN DECODIFICADOR  
DOLBY DIGITAL (para DVD)  
Cuando vea un programa grabado en otra fuente  
(videograbadora o videocámara), utilice las tomas de  
entrada AUDIO/VIDEO de la parte delantera de la  
unidad.  
Si utiliza esta unidad para reproducir un disco DVD  
grabado en formato de sonido envolvente Dolby  
Digital de 5,1 canales, la unidad emitirá un flujo de  
datos DOLBY DIGITAL desde su toma AUDIO  
OUT COAXIAL. Si conecta la unidad a un  
decodificador Dolby Digital, podrá disfrutar de una  
tonalidad más convincente y real, con un sonido  
envolvente potente y de alta calidad similar al de los  
cines.  
Conecte las tomas de salida de audio/vídeo de otra  
fuente a las tomas AUDIO L/R y VIDEO de esta  
unidad.  
K
L
] hasta  
Después, presione [SELECT] o [CH.  
que aparezca “AUX” en la pantalla.  
/
Utilice cables digitales coaxiales de audio  
(disponibles en el comercio) para hacer las  
conexiones de audio.  
Consulte la figura 5 de la página 13  
NOTA:  
Cuando conecte una videograbadora monofónica  
(otra fuente) a esta unidad, conecte la toma de  
salida de audio de la videograbadora monofónica  
(otra fuente) a la toma AUDIO L de esta unidad. El  
audio saldrá igualmente por los canales izquierdo y  
derecho.  
Consulte la figura 7 de la página 14  
NOTAS:  
Asegúrese de apagar todos los componentes del  
sistema antes de conectar otro componente.  
Consulte los manuales de instrucciones de los  
componentes que va a conectar a la unidad.  
Si conecta un decodificador Dolby Digital, ajuste  
CONEXIÓN A UN AMPLIFICADOR  
ESTÉREO EQUIPADO CON TOMAS  
DE ENTRADA DIGITAL (para DVD)  
Utilice un cable digital coaxial de audio (disponible en  
el comercio) para hacer las conexiones de audio.  
Conexión a un amplificador equipado con tomas de  
entrada digital, platina MD o platina DAT.  
la función “DOLBY DIGITAL” a “BITSTREAM”  
para salida de audio en el modo de configuración.  
A menos que se haga la conexión a un  
decodificador Dolby Digital, ajuste la función  
“DOLBY DIGITAL” a “PCM” para salida de  
audio en el modo de configuración. La  
reproducción en una unidad utilizando ajustes  
incorrectos puede generar ruido y distorsión, y  
también puede provocar daños a los altavoces.  
Consulte la figura 6 de la página 13  
NOTAS:  
Fabricado bajo licencia de Dolby Laboratories.  
“Dolby” y el símbolo de la doble D son marcas  
comerciales de Dolby Laboratories.  
La fuente de audio de un disco grabado en formato  
de sonido envolvente Dolby Digital de 5,1 canales  
no se puede grabar como sonido digital mediante  
uAnsaegpúlaretisneadMe DapoagDarAtTo.dos los componentes del  
sCisotnesmulateanlotessmdaencuoanleesctdaer ointrsotrucoccmiopnoensendtee.los  
Acojmuspteonlaenftuenscqióune vDa Oa LcoBnYecDtaIrGaITlaAuLnidaadP. CM”  
para salida de audio en el modo de configuración.  
La reproducción en una unidad utilizando ajustes  
incorrectos puede generar ruido y distorsión, y  
también puede provocar daños a los altavoces.  
ES  
52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IDIOMA DEL MENÚ  
SECCIÓN DE TV/VCR  
TV/VCR  
FUNCIONES Y AJUSTES  
DE TV  
1 Seleccione “LANGUAGE”  
Presione [SETUP].  
Presione [K / L] para apuntar a “LANGUAGE”.  
PARA MIRAR UN PROGRAMA DE TV  
TV/VCR  
2 Seleccione “ENGLISH”, “ESPAÑOL” o  
“FRANÇAIS”  
1 Enchufe el cable eléctrico  
Enchufe el cable eléctrico de la unidad en un  
tomacorriente de CA del hogar.  
NOTA:  
Presione [ENTER] repetidamente para seleccionar  
“ENGLISH” = inglés, “ESPAÑOL” o “FRANÇAIS”  
= francés.  
Si aparecen números en la esquina de la pantalla,  
3 Salga del modo de idioma  
Presione [SETUP] para salir del menú.  
NOTAS:  
presione [POWER] sin desenchufar el cable  
eléctrico.  
Esta función afecta sólo el idioma en el menú de la  
pantalla y no la fuente de audio.  
Si por alguna razón, el menú está en francés,  
presione [SETUP], presione [K / L] para apuntar  
al “LANGAGE [FRANÇAIS]” y presione  
[ENTER] repetidamente para seleccionar el  
idioma deseado y presione [SETUP].  
2 Encienda la unidad  
Presione [POWER] para encender la unidad.  
3 Seleccione el número de canal  
K
L
Presione [CH.  
/
] o los botones numéricos para  
seleccionar su número de canal deseado.  
Nota para el uso de los botones numéricos:  
¡Debe colocar un cero antes de los números de canal  
de una sola cifra (por ejemplo: 02, 03, 04, etc.).  
¡
Cuando seleccione canales de cable de más de 99,  
presione primero [+100] y después las dos últimas  
cifras. (Ejemplo: para seleccionar el canal 125,  
primero presione [+100] y después presione [2] y [5].)  
AJUSTE DEL RELOJ  
TV/VCR  
AJUSTE MANUAL DEL RELOJ  
Asegúrese ...  
La unidad debe estar encendida.  
En el siguiente ejemplo, el reloj debe estar en:  
4 Ajuste el sonido  
X
Y
Presione [VOL.  
/
] para ajustar el volumen.  
Presione [MUTE] para silenciar instantáneamente el  
sonido.  
Presione nuevamente para recuperar el nivel de  
sonido anterior.  
FECHA  
HORA DE AJUSTE  
6 de mayo, 2005  
5:40PM  
NOTA:  
1 Seleccione “AJUSTE RELOJ”  
Presione [SETUP].  
Presione [K / L] para selecciona “AJUSTE RELOJ”  
y presione [ENTER].  
K
L
Si presiona [CH.  
/
] en el modo DVD, puede  
cambiar los canales de TV. Incluso si apaga la  
unidad en el modo DVD, cuando vuelva a  
encender, volverá al modo TV/VCR.  
PARA VER CANALES DE CABLE O  
SATELITE  
2 Seleccione “AJUSTE MANUAL RELOJ”  
Presione [K / L] para seleccionar “AJUSTE  
MANUAL RELOJ” y presione [ENTER].  
Si la unidad está conectada a una caja de cable o  
K
L
] para  
caja de satélite, presione [CH.  
/
seleccionar CH3 o CH4 de acuerdo con el ajuste  
de canal de salida del dispositivo y seleccione el  
canal deseado en el dispositivo.  
3 Seleccione el mes  
Presione [K / L] hasta que aparezca el mes deseado.  
(Ejemplo: Mayo “05”)  
PARA VER UNA ENTRADA EXTERNA  
Presione [B]. (O presione [s] para volver un paso.)  
Cuando se conecta un equipo externo en las tomas  
de entrada AUDIO/VIDEO frontales, presione  
4 Seleccione el día  
Presione [K / L] hasta que aparezca el día deseado.  
(Ejemplo: 6º “06”)  
K
L
[SELECT] o [CH.  
/
] repetidamente hasta que  
aparezca “AUX” en la pantalla.  
Presione [B].  
ES  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GRABACIÓN  
5 Seleccione el año  
Presione [K / L] hasta que aparezca el año deseado.  
(Ejemplo: “2005”)  
GRABACIÓN NORMAL  
Presione [B].  
TV/VCR  
SOLO puede ver el mismo programa que se está  
grabando.  
6 Seleccione la hora  
Presione [K / L] hasta que aparezca la hora deseada.  
(Ejemplo: “5”, “PM”)  
1 Seleccione el canal a grabar  
Presione [B].  
K
L
].  
Presione los botones numéricos o [CH.  
/
NOTA:  
7 Seleccione los minutos  
Presione [K / L] hasta que aparezcan los minutos  
deseados.  
Si la unidad está conectada a una caja de cable o  
caja de satélite, la unidad debe estar en CH3 o  
CH4 y debe seleccionarse el canal a grabar en la  
caja de cable o caja de satélite.  
(Ejemplo: “40”)  
2 Seleccione la velocidad de la cinta  
8 Haga funcionar el reloj  
Presione [SPEED] para seleccionar la velocidad de  
Presione [SETUP].  
cinta deseada (SP/SLP).  
Aunque no aparezcan los segundos, empezará a  
contar desde 00 cuando presione [SETUP]. Utilice  
esta característica para sincronizar el reloj con la hora  
real.  
3 Empiece a grabar  
Presione [RECORD].  
4 Pare la grabación  
Presione [STOP C].  
ES  
54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REANUDACIÓN  
SECCIÓN DE DVD  
DVD-V CD  
REPRODUCCIÓN BÁSICA  
1
Durante la reproducción, presione [STOP C].  
DVD-V CD  
¡Aparecerá el mensaje de continuación en la pantalla  
Para empezar  
¡Conecte la alimentación del amplificador y otros  
de TV.  
componentes, si es necesario.  
2
Presione [PLAY O], la reproducción continuará  
desde el punto donde se paró la reproducción.  
1
Presione [POWER].  
¡La alimentación se conectará.  
¡Para cancelar la continuación, presione dos veces  
[STOP C].  
¡La información de continuación permanece activada  
incluso cuando apaga el interruptor principal.  
2
3
4
Presione [A OPEN/CLOSE] para abrir la  
bandeja de carga del disco.  
Ponga el disco deseado en la bandeja, con  
la etiqueta hacia arriba.  
Presione [PLAY O].  
¡La bandeja se cerrará automáticamente y la  
reproducción comenzará desde el primer capítulo o  
pista del disco.  
¡La reproducción también empieza cerrando  
manualmente la bandeja del disco o presionando  
[A OPEN/CLOSE].  
¡Si la reproducción no comienza automáticamente,  
presione [PLAY O].  
¡Cuando reproduzca un DVD que tenga grabado un  
menú de títulos, el menú podrá aparecer en la  
pantalla.  
5
Presione [STOP C] para detener la  
reproducción.  
MENÚ DE DISCO  
DVD-V  
1
Presione [DISC MENU].  
¡Aparecerá el menú principal de DVD.  
¡Si no existe la función, puede aparecer el símbolo  
en la pantalla de TV.  
¡
Si el menú de disco existe en el disco, aparecerán el  
idioma de audio, opciones de subtítulo, capítulos para el  
título y otras opciones para su selección.  
2
Presione [K / L / s / B] para seleccionar  
un ítem y presione [ENTER] para confirmar  
la selección.  
ES  
55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LIMITED WARRANTY  
FUNAI CORP. will repair this SYLVANIA product, free of charge in the USA in the event of defect in materials or  
workmanship as follows:  
DURATION:  
PARTS:  
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the  
date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this  
warranty.  
LABOR: FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of  
original retail purchase.  
LIMITS AND EXCLUSIONS:  
THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE  
RECEIPT OR OTHER PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH  
THE PRODUCT TO OBTAIN SERVICE UNDER THIS WARRANTY.  
This warranty shall not be extended to any other person or transferee.  
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing  
or if service was attempted by an unauthorized service center. This SYLVANIA Limited warranty does not apply to  
any product not purchased and used in the United States.  
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It  
does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not  
supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication,  
alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this  
product or damage which results from fire, flood, lightning or other acts of God.  
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE  
CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.  
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY  
GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE  
USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL  
OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF  
FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY AND  
FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS  
REPRESENTATIVES IN THE UNITED STATES.  
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY A FUNAI AUTHORIZED  
SERVICE CENTER. THIS WARRANTY IS ONLY VALID WHEN THE UNIT IS CARRIED-IN TO A FUNAI  
AUTHORIZED SERVICE FACILITY.  
IMPORTANT:  
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS  
THAT VARY FROM STATE TO STATE. IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE  
UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI  
CORP.  
ATTENTION:  
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT  
WITHOUT PRIOR NOTICE.  
To locate your nearest Authorized Service Center or for general service procedure, please call or  
write to the following:  
FUNAI CORPORATION, INC.  
SERVICE CENTER  
19900 Van Ness Avenue, Torrance, CA 90501  
Tel :1-800-968-3429  
Head Office: 100 North Street, Teterboro, NJ 07608  
PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.  
Printed in Thailand  
1EMN20670  
T0153UD ★★★★★  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Sherwood Stove EF 3 BAYI User Manual
Shindaiwa Trimmer 81642 User Manual
Shure Headphones SE420 User Manual
Sony Digital Camera AC UB10 User Manual
Sony DVD Player DVP CX777ES B User Manual
Sony Laptop FXA49 User Manual
Sony Projection Television KF 50SX100HK User Manual
Sony Speaker SA WX900 User Manual
Stamina Products Home Gym 50lb User Manual
Star Manufacturing Griddle 624TSPD User Manual