Sylvania TV VCR Combo 63134C 63194C User Manual

OWNER’S

MANUAL

COLOR TV/VCR

63134C (13 inch)

63194C (19 inch)

This Owner’s Manual is made of

recycled paper.

INSTRUCCIONES EN ESPAÑOL INCLUIDAS.

As an ENERGY STAR^®

Partner, our company has

determined that this product meets

the ENERGY STAR^®guidelines for

energy efficiency. ENERGY STAR^®is

a U.S. registered mark.

If you need additional assistance for set-up or operating

after reading owner’s manual, please call

TOLL FREE : 1-800-968-3429

Download from Www.Somanuals.com. All Manuals Search And Download.

Please read before using this equipment

FIGURE A

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

ANTENNA

LEAD I N

WI RE

GROUND

CL AMP

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

ELECTRI C

SERVICE

EQUIPMENT

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

NEC

NATIONAL ELECTRICAL CODE

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

S2898A

13.Outdoor Antenna grounding-If an outside antenna or

cable system is connected to the TV/VCR, be sure the

antenna or cable system is grounded so as to provide some

protection against voltage surges and built-up static

charges. Article 810 of the National Electrical Code,

ANSI/NFPA No. 70, provides information with respect to

proper grounding of the mast and supporting structure,

grounding of the lead-in wire to an antenna discharge unit,

size of grounding conductors, location of antenna-discharge

unit, connection to grounding electrodes, and requirements

for the grounding electrode. (Fig. A)

19.Damage Requiring Service-Unplug this TV/VCR from

the wall outlet and refer servicing to qualified service per-

sonnel under the following conditions:

a. When the power-supply cord or plug is damaged or frayed.

b. If liquid has been spilled, or objects have fallen into the

TV/VCR.

c. If the TV/VCR has been exposed to rain or water.

d. If the TV/VCR does not operate normally by following the

operating instructions. Adjust only those controls that are

covered by the operating instructions, as improper adjust-

ment of other controls may result in damage and will often

require extensive work by a qualified technician to restore

the TV/VCR to its normal operation.

14.Lightning-For added protection for this TV/VCR receiver

during a lightning storm, or when it is left unattended and

unused for long periods of time, unplug it from the wall

outlet and disconnect the antenna or cable system. This will

prevent damage to the TV/VCR due to lightning and

power-line surges.

e. If the TV/VCR has been dropped or damaged in any way.

f. When the TV/VCR exhibits a distinct change in perfor-

mance-this indicates a need for service.

15.Power Lines-An outside antenna system should not be

located in the vicinity of overhead power lines or other

electric light or power circuits, or where it can fall into

such power lines or circuits. When installing an outside

antenna system, extreme care should be taken to keep from

touching such power lines or circuits as contact with them

might be fatal.

20.Replacement Parts-When replacement parts are required,

be sure the service technician has used replacement parts

specified by the manufacturer that have the same character-

istics as the original part. Unauthorized substitutions may

result in fire, electric shock, injury to persons or other haz-

ards.

21.Safety Check-Upon completion of any service or repairs to

this TV/VCR, ask the service technician to perform routine

safety checks to determine that the TV/VCR is in proper

operating condition.

16.Overloading-Do not overload wall outlets and extension

cords as this can result in a risk of fire or electric shock.

17.Object and Liquid Entry-Never push objects of any kind

into this TV/VCR through openings as they may touch dan-

gerous voltage points or short out parts that could result in

a fire or electric shock. Never spill liquid of any kind on

the TV/VCR.

22.Heat-This TV/VCR product should be situated away from

heat sources such as radiators, heat registers, stoves, or

other products (including amplifiers) that produce heat.

18.Servicing-Do not attempt to service this TV/VCR yourself

as opening or removing covers may expose you to danger-

ous voltage or other hazards. Refer all servicing to quali-

fied service personnel.

CAUTION:TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY

INSERT.

ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE

LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

_{Download from Www.Somanuals.com}- 3_{. A}-_{ll Manuals Search And Download.}

9I03

PRECAUTIONS

IMPORTANT COPYRIGHT INFORMATION

LOCATION

For safe operation and satisfactory performance of

your TV/VCR, keep the following in mind when

selecting a place for its installation:

Shield it from direct sunlight and keep it away

from sources of intense heat.

Avoid dusty or humid places.

Avoid places with insufficient ventilation for proper

heat dissipation. Do not block the ventilation holes

at the top and bottom of the unit. Do not place the

unit on a carpet because this will block the ventila-

tion holes.

Unauthorized recording or use of broadcast televi-

sion programming, video tape, film or other copy-

righted material may violate applicable copyright

laws. We assume no responsibility for the unautho-

rized duplication, use, or other acts which infringe

upon the rights of copyright owners.

•

FCC WARNING- This equipment may gener-

ate or use radio frequency energy. Changes or

modifications to this equipment may cause

harmful interference unless the modifications

are expressly approved in the instruction man-

ual. The user could lose the authority to oper-

ate this equipment if an unauthorized change

or modification is made.

Install unit in a horizontal position.

Avoid locations subject to strong vibration.

Do not place the TV/VCR near strong magnetic fields.

Avoid moving TV/VCR to locations where temper-

•

ature differences are extreme.

This equipment has been tested and found to com-

ply with the limits for a Class B digital device, pur-

suant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and

used in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to

radio or television reception, which can be deter-

mined by turning the equipment off and on, the

user is encouraged to try to correct the interfer-

ence by one or more of the following measures:

1) Reorient or relocate the receiving antenna.

2) Increase the separation between the equipment

and receiver.

AVOID THE HAZARDS OF

ELECTRICAL SHOCK AND FIRE

•

Do not handle the power cord with wet hands.

Do not pull on the power cord when disconnecting

it from an AC wall outlet. Grasp it by the plug.

If, by accident, water is spilled on your unit, unplug

the power cord immediately and take the unit to an

Authorized Service Center for servicing.

Do not put your fingers or objects into the

TV/VCR cassette holder.

Do not place anything directly on top of the unit.

•

WARNING

Moisture condensation may occur inside the unit

when it is moved from a cold place to a warm place,

or after heating a cold room or under conditions of

high humidity. If a tape is played in a TV/VCR

which has moisture, it may damage the tape and

TV/VCR. Therefore if condensation occurs inside the

unit, turn the POWER button on and allow at least 2

hours for the unit to dry out.

3) Connect the equipment to an outlet on a circuit

different from that to which the receiver is con-

nected.

4) Consult the dealer or an experienced radio/TV

technician for help.

The serial number of this product may be found on the back of the unit. No other TV/VCR has the same serial

number as yours. You should record the number and other vital information here and retain this book as a per-

manent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.

Date of Purchase

Dealer Purchase from

Dealer Address

Dealer Phone No.

Model No.

Serial No.

_{Download from Www.Somanuals.co}-_m4_{. A}-_{ll Manuals Search And Download.}

9I03

TABLE OF CONTENTS

C IMPORTANT SAFEGUARDS . . . . . . . . . . . . .2

C PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . .4

C FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

C SUPPLIED ACCESSORIES . . . . . . . . . . . . . . .6

C OPERATING CONTROLS AND FUNCTIONS 7

C RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .20

NORMAL RECORDING . . . . . . . . . . . . . . . . .20

OTR (One Touch Recording) . . . . . . . . . . . . . .21

TIMER RECORDING . . . . . . . . . . . . . . . . . . .21

TIMER PROGRAM EXTENSION . . . . . . . . .22

HINTS FOR AUTOMATIC TIMER

RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .23

C PREPARATION FOR USE . . . . . . . . . . . . . . . .9

ANTENNA/CABLE CONNECTIONS . . . . . . .9

EXTERNAL INPUT MODE . . . . . . . . . . . . . .10

INSTALLING THE BATTERIES . . . . . . . . . . .10

AUTO RETURN . . . . . . . . . . . . . . . . . . . . . . .23

WAKE UP TIMER . . . . . . . . . . . . . . . . . . . . . .23

SLEEP TIMER . . . . . . . . . . . . . . . . . . . . . . . . .24

C COPYING A VIDEO TAPE . . . . . . . . . . . . . . .24

C SET UP FOR USE . . . . . . . . . . . . . . . . . . . . .10

CHANNEL SET UP FOR THE FIRST TIME .10

CLOCK SET UP (AUTO / MANUAL) . . . . . .11

CHANNEL SET UP AGAIN . . . . . . . . . . . . . .12

DELETING (OR ADDING) CHANNEL . . . . .12

SELECTING THE LANGUAGE . . . . . . . . . . .13

DAYLIGHT-SAVING TIME . . . . . . . . . . . . . .13

C ON SCREEN DISPLAY . . . . . . . . . . . . . . . . .25

C SPECIAL FEATURES . . . . . . . . . . . . . . . . . .25

REAL TIME TAPE COUNTER . . . . . . . . . . . .25

AUTO REWIND-EJECT . . . . . . . . . . . . . . . . .25

C MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . .25

C TROUBLESHOOTING GUIDE . . . . . . . . . . .26

C SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . .27

C CABLE CHANNEL DESIGNATIONS . . . . . .27

C WARRANTY . . . . . . . . . . . . . . . . . . .Back Cover

C TV OPERATION . . . . . . . . . . . . . . . . . . . . . . .14

WATCHING A TV PROGRAM . . . . . . . . . . . .14

GAME MODE . . . . . . . . . . . . . . . . . . . . . . . . .14

DEGAUSSING . . . . . . . . . . . . . . . . . . . . . . . .14

PICTURE CONTROL . . . . . . . . . . . . . . . . . . .14

CLOSED CAPTION SYSTEM . . . . . . . . . . . .15

V-CHIP SET UP . . . . . . . . . . . . . . . . . . . . . . . .15

C PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . .17

NORMAL PLAYBACK . . . . . . . . . . . . . . . . . .17

AUTO REPEAT PLAYBACK . . . . . . . . . . . . .18

SEARCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

SLOW MOTION . . . . . . . . . . . . . . . . . . . . . . .19

RENTAL PLAYBACK . . . . . . . . . . . . . . . . . . .19

VERTICAL HOLD CONTROL . . . . . . . . . . . .20

STILL PICTURE . . . . . . . . . . . . . . . . . . . . . . .20

TRACKING ADJUSTMENT . . . . . . . . . . . . . .20

A NOTE ABOUT RECYCLING

This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in

accordance with your local recycling regulations.

Batteries should never be thrown away or incinerated but disposed of in accordance with your local regula-

tions concerning chemical wastes.

_{Download from Www.Somanuals.com}- 5_{. A}-_{ll Manuals Search And Download.}

9I03

FEATURES

Rotary 4-head Record/Playback System–Four

heads ensure excellent picture quality and special

effects playback.

Index Search–Fast-forwards to start of next recording.

Slow Motion–View recorded program at slower

than normal speed.

Infrared remote control

Bilingual on screen menu display selectable in

English or Spanish

Auto Head Cleaner–Automatically cleans video

•

heads as you insert or remove a cassette.

Zero Return–The tape returns to counter of

0:00:00 by rewinding or fast forwarding.

Still–“Freeze” the picture at any time, for close

viewing of a particular scene. Only tapes recorded

in SLP mode will show a fairly clear picture.

Digital Auto Tracking (DTR)–Automatically

adjusts the tracking for each tape you play.

Rental play mode–Improves playback picture

quality from worn tapes, such as rental tapes.

Auto repeat–Allows you to repeat the playing of a

tape indefinitely without pressing the PLAY button.

Time search–Lets you set the TV/VCR to advance

the tape by entering the desired playback time you

want to skip.

•

Real time counter–This shows the elapsed record-

ing or playback time in hours, minutes, and sec-

onds. The “–” indication will appear when the tape

is rewound further than the tape counter position

“0:00:00”.

181 channel capability PLL frequency synthesiz-

er tuner with direct station call–(A converter may

be necessary to view scrambled cable channels.)

Auto Clock Setting–Allows you to set the clock

from a PBS broadcast station.

Closed caption system–You may view specially

labeled (cc) TV programs, movies, news, prere-

corded tapes, etc. with either a dialogue caption or

text display added to the program.

Game mode–Automatically sets external input

mode and allows the TV/VCR display to be suit-

able for use with TV games.

Auto power on and off system–Automatically

turns on the TV/VCR when you insert the cassette,

turns off after auto-rewind, and ejects when the

beginning of the tape is reached.

Auto rewind when the end of a tape is

reached–This function doesn’t occur when using

timer recording.

2 Step picture search operation–You can view a

video program at a high speed or super high speed

in either a forward or reverse direction in LP and

SLP mode. For SP mode only high speed.

Three different playback tape speeds : SP/LP/SLP

Two different recording tape speeds : SP/SLP

•

OTR (One Touch Recording)–Instant timed

recording from 30 to 480 minutes is possible at the

push of the REC/OTR button.

•

1 Year, 8 events (including Daily and Weekly

Timer Recording)–The built-in timer allows you to

record up to 8 programs at different times on dif-

ferent channels up to 1 year in advance. The Daily

timer allows recordings to be made of daily broad-

casts, and the Weekly timer allows recording to be

made once a week up to the end of the tape.

Auto return–After timer recording is finished, the

TV/VCR can return to the beginning of the record-

ing.

Wake-up/Sleep timer–Allows you to have the

TV/VCR automatically turn on or off at a desired

time.

Timer Program Extension–Allow you to shift the

time schedule for automatic timer recording.

V-CHIP–Enables parents to prevent their children

from watching inappropriate material on TV.

•

SUPPLIED ACCESSORIES

Remote Control Unit

PART NO. (NO146UD)

2 AA Batteries

Rod Antenna (13” model only)

PART NO. (0EMN00673 or

0EMN01599 or0EMN01755)

If you need to replace these accessories, please refer to the PART NO. under the illustrations and call 1-800-

968-3429.

Depending on your antenna system, you may need different types of Combiners (Mixer) or Separators

(Splitter). Contact your local electronics store for these items.

We do not recommend the use of universal remote controls. Not all of the functions may be controlled with

a universal remote control. If you decide to use a universal remote control with this unit, please be aware

that the code number given may not operate this unit. In this case, please call the manufacturer of the uni-

versal remote control.

•

_{Download from Www.Somanuals.co}-_m6_{. A}-_{ll Manuals Search And Download.}

9I03

OPERATING CONTROLS AND FUNCTIONS

This manual covers 13 and 19 . The operation of the two models are exactly the same except the

appearance. 19 model is illustrated in this manual.

- TV/VCR FRONT PANEL -

VIDEO AUDIO

POWER

CHANNEL

STOP/EJECT

REW PLAY F.FWD

REC/OTR EARPHONE

VOLUME

1 2 3 4 5 6 7 8 9101112

- REMOTE CONTROL -

1 VIDEO input jack– Connect to the video output

jack of your video camera or another VCR.

2 AUDIO input jack– Connect to the audio output

jack of your audio equipment, video camera or

another VCR.

WAKE-UP

/SLEEP

POWER

EJECT

CHANNEL

RETURN

3 POWER button– Press to turn TV/VCR on and

off. Press to activate timer recording.

VOLUME X / Y buttons– Adjust the volume level.

CHANNEL

VOLUME

5 CHANNEL K / L buttons– Press to select the

desired channels for viewing or recording.

You may display the main menu on the TV screen

by pressing repeatedly this button on the TV/VCR.

TRACKING function– Press to minimize video

‘noise’ (lines or dots on screen) during playback or

Slow mode. (See page 20.)

6 Remote Sensor Window– Receives the infrared

signals from the remote control.

7 STOP button– Press to stop the tape motion.

EJECT button– Press in the Stop mode to remove

tape from TV/VCR.

+100

DISPLAY

MUTE

PLAY

REW

F.FWD

STOP

SPEED PAUSE/STILL

RECORD

T-PROG.

CLEAR

GAME

SLOW

COUNTER

RESET

L button–

Press to select setting modes from the on screen

menu.

•

Press to enter digits when setting program.

(for example: setting clock or timer program)

•

8 REW button– Press to rewind the tape, or to view

the picture rapidly in reverse during playback

mode. (Rewind Search)

s button–

Press to select a mode from a particular menu.

(for example: LANGUAGE or USER’S SET UP)

•

_{Download from Www.Somanuals.com}- 7_{. A}-_{ll Manuals Search And Download.}

9I03

- REAR VIEW -*

ANT.

18 SPEED button– Press to choose the desired

recording speed:SP/SLP.

9 PLAY button– Press to begin playback.

K button–

19 T-PROG. CLEAR button– Press to cancel a setting

of timer program. (See page 23.)

Press to select setting modes from the on screen

menu.

•

COUNTER RESET button– Press to reset counter

to 0:00:00.

Press to enter digits when setting program.

•

(for example: setting clock or timer program)

10 F.FWD button– Press to rapidly advance the tape,

or to view the picture rapidly in forward during

playback mode. (Forward Search)

20 GAME button– Sets the game mode and external

input mode at the same time. (See page 14.)

21 SLOW button– Press to start slow motion playback.

22 PAUSE/STILL button– Press to temporarily stop

the tape during the recording or to view a still pic-

ture during playback.

Frame Advance function– Press to advance the

picture one frame at a time during Still mode.

23 MUTE button– Mutes the sound. Press it again to

resume sound.

24 CHANNEL RETURN button– Press to go back to

the previously viewed channel. For example,

pressing this button once will change channel dis-

play from 3 (present channel) to 10 (previously

viewed channel), and pressing it a second time

will return from 10 to 3.

25 WAKE UP/SLEEP button– Sets the Wake up or

Sleep Timer. (See page 23 and 24.)

26 EJECT button– Press in the Stop mode to remove

a tape from the TV/VCR.

27 Power cord– Connect to a standard AC outlet

(120V/60Hz).

28 ANT. terminal– Connect to an antenna or cable

system.

B button–

When setting program (for example: setting clock

or timer program), press to determine your selec-

tion and proceed to the next step you want to input.

Press to determine setting modes from on screen

menu.

•

Press to select a mode from a particular menu.

•

(for example: LANGUAGE or USER’S SET UP)

11 REC button– Press for manual recording.

OTR button– Activates One Touch Recording.

(only on the TV/VCR)

12 RECORD indicator– Flashes during recording.

Lights up in the Stand-by mode for Timer Recording.

13 EARPHONE jack– Connects to earphones (not

supplied) for personal listening. The size of jack is

1/8” monaural (3.5mm).

14 Cassette compartment

15 Number buttons– Press to select desired channels

for viewing or recording. To select channels from

1 to 9, first press the 0 button and then 1 to 9.

+100 button– When selecting cable channels which

are higher than 99, press this button first, then press

the last two digits. (To select channel 125, first press

the “+100” button then press “2” and “5”).

16 MENU button– Press to display the main menu on

the TV screen.

17 DISPLAY button– Display the counter or the cur-

rent channel number and current time on the TV

screen. (See page 25.)

_{Download from Www.Somanuals.co}-_m8_{. A}-_{ll Manuals Search And Download.}

9I03

PREPARATION FOR USE

ANTENNA/CABLE CONNECTIONS

From Cable System or

Satellite Dish

VHF/UHF Antenna

(Not supplied)

Satellite Box or

Cable Box

(Not supplied)

Rod Antenna

(Supplied with 13” model only)

OUT

VHF Antenna

(Not supplied)

UHF Antenna

(Not supplied)

From

Cable System

VHF/UHF

Combiner

(Not supplied)

ANT.

75-ohm Coaxial

Cable (Not supplied)

Flat twin-lead cable

VHF/UHF COMBINED ANTENNA

VHF/UHF SEPARATE ANTENNAS

The VHF/UHF Rod Antenna (supplied with 13”

model only) is detachable. Insert the stem of the

antenna into the hole on the upper-back portion of

the TV/VCR.Connect the VHF/UHF Rod Antenna or

VHF/UHF Combination Antenna to the ANT. termi-

nal of the TV/VCR as shown in the diagram. For the

best reception, fully extend the VHF/UHF Rod

Antenna and make the necessary adjustments. (Avoid

touching the top section when adjusting.)

NOTE:

In some areas it will be necessary to use an outdoor

antenna.

CABLE WITHOUT CONVERTER/

DESCRAMBLER BOX

Use this connection if your cable system connects

directly to your TV/VCR without a converter box.

By using this connection you can:

1) Use the TV/VCR remote to select channels.

2) Program one or more unscrambled channels for

Automatic Timer Recording.

NOTE: This unit will ONLY record and view the

same channel.

Before plugging the Rod antenna into antenna termi-

nal, check that the pin is not bent. If it is bent,

straighten the pin as illustrated, then plug the pin into

antenna terminal.

CABLE WITH CONVERTER/

DESCRAMBLER BOX OR SATELLITE

BOX

Bent pin

If your cable service supplies you with a converter

box or if you use a satellite system, you can use the

basic connection shown in the diagram.

By using this connection you can also record scram-

bled channels. However, channel selection must be

made with the converter box or satellite box. This

means that channels cannot be changed using the

TV/VCR Remote Control. Unattended timer record-

ing is limited to one channel at a time.

Cable Plug

(Straight pin)

(Needs to be straightened)

NOTE:

The connection of an indoor antenna may not always

give acceptable TV reception.

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that

provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connect-

ed to the grounding system of the building as close to the point of cable entry as practical.

_{Download from Www.Somanuals.com}- 9_{. A}-_{ll Manuals Search And Download.}

9I03

TO RECORD A SCRAMBLED/UNSCRAMBLED

CHANNEL

INSTALLING THE BATTERIES

1) Set the TV/VCR channel selector to the output

channel of the Cable Converter Box or Satellite

Box. (Example: CH3)

2) Select the channel to record from your Cable

Converter Box or Satellite Box.

1)Open the battery compartment cover by pressing

the cover on the remote unit in the direction of the

arrow.

2)Insert 2 “AA” penlight batteries into the battery

compartment in the direction indicated by the

polarity (+/-) markings.

3)Replace the cover.

EXTERNAL INPUT MODE

When using an external input signal (another VCR or

video camera), connect the player’s audio/video out-

put cables to the AUDIO IN/ VIDEO IN jacks of

your TV/VCR. Then press the CHANNEL K or

button until “AUX” appears on the screen.

NOTE: “AUX” is found below the

lowest memorized channel.

AUX

(Example: CH2)

SET UP FOR USE

You can program the tuner to scan all the channels you receive in your area.

NOTE: Channel memory programming is NOT needed when connected to a cable box or satellite box. Just

select the TV/VCR channel selector to the output channel of the cable box or satellite box (Ex CH3). Then

select the channel to be viewed on the Cable Box or Satellite Box.

CHANNEL SET UP FOR THE

4 Begin auto preset

– SET UP –

FIRST TIME

Press the PLAY/K or STOP/L but-

LANGUAGE

[ENGLISH] ESPAÑOL

ton to point to “AUTO PRESET”.

1 Plug in the TV/VCR power cord

AUTO PRESET

Then press the F.FWD/B button.

The tuner scans and memorizes all

active channels in your area.

NOTES:

The TV/VCR distinguishes between standard TV

channels and cable channels.

If you want to play or record a video tape

BEFORE presetting the tuner, you must press the

MENU button on the remote control. To preset the

tuner again, see “CHANNEL SET UP AGAIN” on

page 12.

Plug the TV/VCR power cord into a

standard AC outlet.

NOTE:

If some digits appear in the corner of

the screen, press the POWER button

without unplugging the power cord.

•

2 Turn on the TV/VCR

Press the POWER button to turn on the TV/VCR

The TV/VCR may memorize TV channels as

CATV channels if reception conditions are poor. If

this happens, try the AUTO MEMO action again

when reception conditions are better.

•

3 Select “ENGLISH” or “ESPAÑOL”

Select “ENGLISH” or

– SET UP –

“ESPAÑOL”=Spanish using the

LANGUAGE

[ENGLISH] ESPAÑOL

F.FWD/B or REW/s button. “[ ]”

indicate the selected language.

AUTO PRESET

5 After scanning

The tuner stops on the lowest memorized channel.

If you want to recall the selected channels, you can

select the desired channel directly with the remote

control number buttons or CHANNEL K or L button.

- 10 -

9I03

Download from Www.Somanuals.com. All Manuals Search And Download.

1 Select “SETTING CLOCK”

Press the MENU button on the

remote control.

Press the PLAY/K or STOP/L but-

ton to point to “SETTING

CLOCK”.

– M E N U –

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

TO SELECT A DESIRED CHANNEL

You can select the desired channel by using the

CHANNEL K or L button or directly pressing the

number buttons on the remote control.

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

Note for using the number buttons:

Then, press the F.FWD/B button.

When selecting cable channels which are higher

•

than 99, press the +100 button first, then, press the

last two digits. (Example: to select channel 125,

first press the +100 button then press “2” and “5”).

– SETTING CLOCK –

2 Set “AUTO CLOCK” to [ON]

Press the F.FWD/B or REW/s

button repeatedly until [ON]

appears.

AUTO CLOCK

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ON]

[AUTO]

You must proceed single-digit channel numbers

with a zero (Example: 02 ... 09).

•

[OFF]

CLOCK SET UP

3 Enter the channel number for the PBS station

(AUTO / MANUAL)

Press the PLAY/K or STOP/L but-

– SETTING CLOCK –

ton to point to “AUTO CLOCK

CH”.

Then press the F.FWD/B or

REW/s button until the channel

number for your local PBS station

appears.

Set the clock accurately for proper automatic timer

recording. If the Public Broadcasting Station (PBS)

is available in your area, follow “AUTO CLOCK

SETTING”. If it is not, follow “MANUAL CLOCK

SETTING”.

AUTO CLOCK

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ON]

[AUTO]

[OFF]

If you do not know the PBS channel number, leave it

set to [AUTO] which is located before [2]. The

TV/VCR will search automatically all available chan-

nels for the local PBS station, and will select that

channel.

AUTO CLOCK SETTING

You can have the TV/VCR set the clock automatical-

ly by using the Public Broadcasting Station (PBS)

channel in your area. Once you have set the clock by

using the following procedure, the TV/VCR will

automatically monitor the correct time and date

being broadcast by the PBS station in your area,

using a new service called Extended Data Service

(XDS).

4 Exit the Auto Clock Setting

Press the MENU button on the remote control to

return to TV mode.

Make sure ...

5 Turn off the TV/VCR

Turn the TV/VCR off. The Auto Clock functions

automatically while the TV/VCR is off.

TV/VCR power must be turned on.

Confirm that the antenna connections are correct.

The cable converter box must be turned on if your

TV/VCR is connected directly to it. (See NOTES:)

•

If you choose [AUTO],

The TV/VCR must search until the PBS channel is

found. It must scan each channel for a couple of

seconds to determine if that channel is transmitting

the XDS signal.

The channel is properly set in advance.

•

NOTES:

Auto clock setting only needs to be set once. But it

can be done again if the clock’s time has become

incorrect for some reason.

•

If the time that is automatically set by this selected

•

PBS station is incorrect, it may not be your local

PBS station, but one from a different time zone.

Or if no channel is broadcasting the XDS signal in

your area, no time will show. In these cases, you

must manually enter the correct local PBS station,

or set the clock manually and turn off the Auto

Clock Setting feature.

If the TV/VCR is connected directly to a cable

•

converter box or satellite box, the local PBS station

must be selected on the cable box itself, and the

TV/VCR must be set to the output channel of the

cable converter box or satellite box (usually chan-

nel 3 or 4), to be able to set up or correct the clock

automatically.

MANUAL CLOCK SETTING

Make sure ...

TV/VCR power must be turned on.

In the example below, the clock is to be set to:

If you do not know what your local PBS station is,

then follow “Manual Clock Settings”.

The TV/VCR cannot control the channels of the

cable converter box or satellite box.

•

DATE

May 7th, 2002

SETTING TIME 5:40PM

- 11 -

9I03

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTE:

When unplugging the AC cord or if there is a power

failure for more than 3 seconds, you may have to

reset the clock.

– M E N U –

1 Select “SETTING CLOCK”

Press the MENU button on the

remote control. Press the PLAY/K

or STOP/L button to point to “SET-

TING CLOCK”.

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

TO CHANGE CLOCK SETTING

INDEX SEARCH

If you want to change the clock,

1)Follow steps [1] and [2].

Then, press the F.FWD/B button.

2)Select where you want to change using the

F.FWD/B or REW/s button.

3)Enter correct numbers using the PLAY/K or

STOP/L button.

4)Press the MENU button on the remote control to

start the clock.

– SETTING CLOCK –

2 Select “MANUAL CLOCK

AUTO CLOCK

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ON]

SET”

[AUTO]

[OFF]

Press the PLAY/K or STOP/L but-

ton to point to “MANUAL CLOCK

SET”.

Then, press the F.FWD/B button.

PLEASE NOTE:

– MANUAL CLOCK SET –

MONTH DAY YEAR

If there is no local PBS station in your area or on

your cable system, select “AUTO CLOCK” and press

the F.FWD/B or REW/s button to turn [OFF] this

function. Then you can manually adjust the clock.

3 Select the month

Press the PLAY/K or STOP/L but-

ton until your desired month

appears. (Example: May → 05)

Then, press the F.FWD/B button.

0 5

– – – – – – – – –

HOUR

– –

MINUTE

– – – –

CHANNEL SET UP AGAIN

Make sure ...

– MANUAL CLOCK SET –

MONTH DAY YEAR

4 Select the day

Press the PLAY/K or STOP/L but-

ton until your desired day appears.

(Example: 7th → 07)

Press the POWER button to turn on the TV/VCR.

•

0 5

0 7 – – – – – – –

HOUR

– –

MINUTE

– – – –

1 Select “CHANNEL SET UP”

Then, press the F.FWD/B button.

– M E N U –

Press the MENU button on the

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

remote control.

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

– MANUAL CLOCK SET –

MONTH DAY YEAR

5 Select the year

Press the PLAY/K or STOP/L but-

ton until your desired year appears.

(Example: 2002)

Press the PLAY/K or STOP/L but-

ton to point to “CHANNEL SET

UP”.

0 5

0 7 TUE 2 0 0 2

TIME SEARCH

INDEX SEARCH

HOUR

– –

MINUTE

– – – –

Then, press the F.FWD/B button.

2 Begin auto preset

– CHANNEL SET UP –

– MANUAL CLOCK SET –

MONTH DAY YEAR

6 Select the hour

Press the PLAY/K or STOP/L but-

ton until your desired hour appears.

(Example: 5, PM)

ADD / DELETE CH (TV)

AUTO PRESET

Press the PLAY/K or STOP/L but-

ton to point to “AUTO PRESET”.

Then, press the F.FWD/B button.

The tuner scans and memorizes all

the active channels in your area.

0 5

0 7 TUE 2 0 0 2

HOUR

0 5

MINUTE

– – PM

Then, press the F.FWD/B button.

– MANUAL CLOCK SET –

MONTH DAY YEAR

7 Select the minute

Press the PLAY/K or STOP/L but-

ton until the desired minute appears.

(Example: 40)

3 After scanning

The tuner stops on the lowest memorized channel.

0 5

0 7 TUE 2 0 0 2

HOUR

0 5

MINUTE

4 0 PM

DELETING (OR ADDING)

CHANNEL

The channels you no longer receive or seldom watch

can be deleted from the memory. (Of course, you

can add the deleted channel into the memory again.)

5:40 PM

8 Start the clock

Press the MENU button on the

remote control.

Although seconds are not displayed,

they begin counting from 00 when

you press the MENU button on the remote control.

Use this feature to synchronize the clock with the

correct time.

- 12 -

9I03

Download from Www.Somanuals.com. All Manuals Search And Download.

1 Select “CHANNEL SET UP”

Press the MENU button on the

remote control.

Press the PLAY/K or STOP/L but-

ton to point to “CHANNEL SET

UP”.

2 Select “ENGLISH” or “ESPAÑOL”

Select “ENGLISH” or “ESPAÑOL”= Spanish using

the F.FWD/B or REW/s button.

– M E N U –

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

3 Exit the Language mode

Press the MENU button on the remote control to

return to TV mode.

TIME SEARCH

INDEX SEARCH

Then, press the F.FWD/B button.

NOTE: If for some reason the menu is in Spanish,

press the MENU button on the remote control, press

the PLAY/K button to point to “IDIOMA

[ESPAÑOL]”, then press the F.FWD/B button, then

press the MENU button on the remote control.

– CHANNEL SET UP –

2 Select “ADD/DELETE CH”

Press the PLAY/K or STOP/L but-

ton to point to “ADD/DELETE

CH”.

ADD / DELETE CH (TV)

AUTO PRESET

Press the F.FWD/B button.

DAYLIGHT-SAVING TIME

Select this feature and the TV/VCR’s clock automati-

cally will advance one hour in April, then reverse one

hour in October.

When Daylight-Saving Time is ON, the clock will

change automatically as follows:

First Sunday of April : At 2 AM the clock imme-

3 Enter the desired channel number

Press the PLAY/K or STOP/L but-

ton until your desired channel num-

ber appears. (You can also use the

number buttons or the CHANNEL

K/L button to enter it.) (Example:

CH8)

ADD / DELETE

•

diately changes to 3 AM. Any timer programming

you have set to occur between 2 AM and 3 AM

will not record.

4 Delete (or add) it from (into) memory

Press the F.FWD/B or REW/s button. The channel

number changes to light red. The channel is deleted

from memory.

Last Sunday of October : At 2 AM the clock

immediately changes to 1 AM.

Make sure ...

Press the POWER button to turn on the TV/VCR.

•

To delete another channel, repeat steps [3] and [4].

If you press the F.FWD/B or REW/s button

again, the channel is memorized again.

•

1 Select “SETTING CLOCK”

Added channel: Light blue.

Deleted channel: Light red.

– M E N U –

Press the MENU button on the

TIMER PROGRAMMING

PICTURE CONTROL

remote control.

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

Press the PLAY/K or STOP/L but-

ton to point to “SETTING CLOCK”.

Then, press the F.FWD/B button.

5 Exit the channel setup mode

Press the MENU button on the remote control to

returns to TV mode.

TIME SEARCH

INDEX SEARCH

NOTE: To confirm that channel(s) has been deleted

or added, press the CHANNEL K or L button.

2 Set “D.S.T.” (Daylight-Saving Time) to [ON]

– SETTING CLOCK –

Press the PLAY/K or STOP/L but-

ton to point to “D.S.T.”.

Then, press the F.FWD/B or

REW/s button until [ON] appears.

AUTO CLOCK

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ON]

[AUTO]

SELECTING THE LANGUAGE

Make sure ...

[ON]

Press the POWER button to turn on the TV/VCR.

NOTE: This function effects only the language on

the screen menu and not the audio source.

•

3 Exit the Daylight-Saving Time mode

Press the MENU button on the remote control to

return to TV mode.

– M E N U –

1 Select “LANGUAGE”

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

Press the MENU button on the

CHANNEL SET UP

USER’S SET UP

TO CANCEL THE DAYLIGHT-SAVING

TIME

Repeat steps [1] to [2], select [OFF] using the

F.FWD/B or REW/s button.Then, press the MENU

button on the remote control to return to TV mode.

remote control.

Press the PLAY/K or STOP/L but-

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

ton to point to “LANGUAGE”.

- 13 -

9I03

Download from Www.Somanuals.com. All Manuals Search And Download.

TV OPERATION

WATCHING A TV PROGRAM

PICTURE CONTROL

The TV/VCR’s picture controls – BRIGHT, CON-

TRAST, COLOR, TINT and SHARPNESS – are

preset to factory specifications. Although they are

usually the best, you may need to make some further

adjustments for a natural looking image.

NOTES:

1 Turn on the TV/VCR

Press the POWER button to turn on the TV/VCR.

2 Select the channel number

Press the CHANNEL K or L button to select your

desired channel number or press the number buttons

on the remote control.

Remember: If the TV/VCR is connected to a cable

box or satellite box, the TV/VCR must be on CH3 or

CH4, then the channel to be viewed must be selected

on the cable box or satellite box.

Procedures must be followed within 5 seconds or

the Picture Control mode will be cancelled.

•

When setting the Picture Control, the Game mode

will be cancelled.

•

Make sure ...

TV/VCR power must be turned on.

•

1 Select “PICTURE CONTROL”

3 Adjust sound

Press the VOLUME or button

to adjust the volume.

Press the MENU button on the

– M E N U –

TIMER PROGRAMMING

remote control.

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

Press the PLAY/K or STOP/L but-

ton to point to ”PICTURE CON-

TROL”.

VOLUME 20

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

Then, press the F.FWD/B button.

GAME MODE

2 Select item you want to adjust

Press the PLAY/K or STOP/L button until desired

This function enables you to decrease the TV screen

contrast and making it suitable for use with a TV

GAME.

control is displayed.

BRIGHT

CONTRAST

NOTE: This function can not be set during recording.

BRIGHT

COLOR

–

P +

TINT

Press the GAME button on the

GAME

remote control. “GAME” appears

on the screen.

SHARPNESS

3 Adjust the picture control

When you press the GAME button;

Press the F.FWD/B or REW/s button to adjust to

The TV/VCR comes on automatically if it is off.

The TV/VCR will be in external input mode auto-

•

your desired level.

matically.

REW/s

to decrease

brightness

to decrease

contrast

F.FWD/B

to increase

brightness

to increase

contrast

TO CANCEL THE GAME MODE

Press the GAME button or CHANNEL K or L but-

ton on the remote control.

BRIGHT

CONTRAST

COLOR

TINT

SHARPNESS to soft

to pale

to brilliant

DEGAUSSING

Magnetism from nearby appliances might affect the

color of the TV picture.

to purple

to green

to clear

If this happens, move this unit away from the appli-

ance. If the color is still not correct, disconnect

power cord from AC outlet then reconnect it after 30

minutes.

If there is a power failure of any kind, the unit will

retain its memory for this feature.

•

- 14 -

9I03

Download from Www.Somanuals.com. All Manuals Search And Download.

TO CANCEL THE CLOSED CAPTION

SYSTEM

Repeat steps [1] and [2], select [OFF] using the

F.FWD/B or REW/s button. Press the MENU but-

ton on the remote control to return to TV mode.

CLOSED CAPTION SYSTEM

You can view specially labeled (cc) TV programs,

movies, news, pre-recorded tapes with either a dia-

logue caption or text display.

CAPTION mode: By choosing the caption mode, you

can watch dramas, movies and news while captioning WHEN THE CLOSED CAPTION MODE

the dialogues and the contents of news.

TEXT mode: By choosing the text mode, you can

watch half screen text information if you want.

1-2: You may get these captions or text information

by selecting either “1” or “2”. Caption “2” is usually

used for a second language if available.

IS ON

The On-Screen Display will disappear after 5 sec-

onds.

This is also true when the MUTE button is pressed,

and when the PAUSE/STILL button is pressed

•

while recording.

If there is a power failure of any kind, the unit will

retain its memory for this feature.

•

NOTE:

Not all programs are broadcast with closed captions.

Your television is designed to provide error free

closed captions from high quality antenna, cable and

VCR signals. Conversely, poor quality signals are

likely to result in caption errors or no captions at all.

V-CHIP SET UP

V-CHIP enables parents to prevent their children

Common signal conditions which may cause captions from watching inappropriate material on TV.

errors are listed below:

V-CHIP reads the ratings for programming (except

for news and sports programs, unedited movies on

premium cable channels, and Emergency Broadcast

System signals), then denies access to programming

if the program’s rating meets the limitations you

select. In this case, “PROTECTED PROGRAM by

...” message appears on the TV screen.

Automobile ignition noise

Electric motor brush noise

Weak snowy reception on TV screen

Multiplex signal reception displaying picture

•

ghosts or airplane flutter.

Playback of poorly recorded or worn VCR tapes.

NOTE:

•

To block certain ratings, follow the steps below.

Programming may be rated by the Motion Picture

•

If the TV/VCR displays a black box on the TV

screen, this means that the TV/VCR

is set to the TEXT mode. To clear

screen, select [CAPTION1], [CAP-

TION2] or [OFF].

Association of America (MPAA) or according to

the Television Parental Guidelines. In order to

block any inappropriate programming, set your

limits in both places (MPAA RATING and TV

RATING).

Make sure ...

TV/VCR power must be turned on.

•

TV RATING SET UP

Make sure ...

– M E N U –

1 Select “CAPTION”

TIMER PROGRAMMING

TV/VCR power must be turned on.

•

PICTURE CONTROL

SETTING CLOCK

Press the MENU button on the

CHANNEL SET UP

USER’S SET UP

remote control.

Press the PLAY/K or STOP/L but-

ton to point to “CAPTION”.

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

1 Select “V-CHIP SET UP”

– M E N U –

TIMER PROGRAMMING

PICTURE CONTROL

Press the MENU button on the

SETTING CLOCK

CHANNEL SET UP

remote control.

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

Press the PLAY/K or STOP/L but-

ton to point to “V-CHIP SET UP”.

Then, press the F.FWD/B button.

2 Select your desired caption menu

INDEX SEARCH

– M E N U –

Press the F.FWD/B or REW/s

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

button until your desired caption

menu appears.

([CAPTION1], [CAPTION2],

[TEXT1] or [TEXT2])

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [CAPTION1]

ZERO RETURN

2 Select “TV RATING”

– V-CHIP SET UP –

TV RATING

MPAA RATING

TIME SEARCH

Press the PLAY/K or STOP/L but-

ton to point to “TV RATING”.

Then, press the F.FWD/B button.

INDEX SEARCH

3 Exit the caption setting mode

Press the MENU button on the remote control to

return to TV mode.

- 15 -

9I03

Download from Www.Somanuals.com. All Manuals Search And Download.

3 Select your desired item

Press the PLAY/K or STOP/L but-

ton to point to your desired item.

Then, press the F.FWD/B button to

select [BLOCK] or [VIEW].

4 Exit the V-Chip setting mode

Press the MENU button on the remote control to

return to original mode.

TV–Y

TV–Y7

TV–G

TV–PG (

TV–14

TV–MA(

[VIEW]

(

)

(

MPAA RATING SET UP

Make sure ...

When you select the rating category and turn it

•

TV/VCR power must be turned on.

[BLOCK], the higher rating will turn [BLOCK]

automatically. Also, the lower rating will turn

[VIEW] automatically.

When you turn “TV-Y” to [VIEW], then all ratings

will turn to [VIEW] automatically.

•

1 Select “V-CHIP SET UP”

Press the MENU button on the

remote control.

– M E N U –

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

Selection

TV-Y

TV-Y7

TV-G

Rating Category Explanations

Appropriate for all children

Appropriate for children seven and older

General Audience

Press the PLAY/K or STOP/L but-

ton to point to “V-CHIP SET UP”.

Then, press the F.FWD/B button.

INDEX SEARCH

TV-PG

TV-14

Parental Guidance suggested.

Unsuitable for children under 14

– V-CHIP SET UP –

2 Select “MPAA RATING”

TV RATING

MPAA RATING

Press the PLAY/K or STOP/L but-

ton to point to “MPAA RATING”.

Then, press the F.FWD/B button.

TV-MA Mature audience only

When you select TV-Y7, TV-PG, TV-14, or TV-MA

and you press the F.FWD/B button, the sub-ratings

will appear on the TV screen.

If you select the rating category (example: TV-PG)

and turn it [BLOCK] or [VIEW], the sub-ratings

(example: V for Violence) will turn [BLOCK] or

[VIEW] automatically.

You can set the sub-ratings to [BLOCK] or [VIEW]

individually when the rating category is set to

[BLOCK].

3 Select your desired item

Press the PLAY/K or STOP/L but-

ton to point to your desired item.

Then, press the F.FWD/B button to

select [BLOCK] or [VIEW].

[VIEW]

PG–13

NC–17

[VIEW]

[BLOCK]

Selection

Rating Category Explanations

General Audience

To set the sub-ratings individually, follow the steps

below.

PG-13

Parental Guidance suggested.

Unsuitable for children under 13

Restricted; under 17 requires accompa-

nying parent or adult guardian

No one under 17 admitted

When you select [TV-Y7]:

•

Press the STOP/L or PLAY/K

button to select “FV” (Fantasy

Violence).

TV–Y7

[BLOCK]

NC-17

Then, press the F.FWD/B button

to select [BLOCK] or [VIEW].

Mature audience only

When you select the rating category and turn it

[BLOCK], the higher rating will turn [BLOCK]

automatically. Also, the lower rating will turn

[VIEW] automatically.

When you turn “G” to [VIEW], then all ratings

will turn to [VIEW] automatically.

•

When you select [TV-PG], [TV-

•

14] or [TV-MA]:

TV–PG

[BLOCK]

Press the STOP/L or PLAY/K

button to select “D”(Suggestive

Dialog), “L”(Coarse Language),

“S”(Sexual Situation), or

“V”(Violence). Then, press the

F.FWD/B button to select

[BLOCK] or [VIEW].

[BLOCK]

TV–Y

TV–Y7

TV–G

TV–PG (DLSV)

TV–14 (DLSV)

TV–MA ( LSV)

[VIEW]

(

)

[VIEW]

4 Exit the V-Chip setting mode

Press the MENU button on the remote control to

return to original mode.

[VIEW]

[BLOCK]

Note: When you select [TV-MA],

“D” does not appear on the TV screen.

The sub-ratings which set to [BLOCK] appears

next to the rating category in the TV RATING

menu.

•

- 16 -

9I03

Download from Www.Somanuals.com. All Manuals Search And Download.

PLAYBACK

This TV/VCR will operate with any cassette that has the

mark. For best results, we

recommend the use of high-quality tapes. Do not use poor quality or damaged tapes.

INSERTING A CASSETTE

Insert the cassette in the direction as shown. Push in

NORMAL PLAYBACK

gently, but continuously, on the center-back of the

cassette until it is drawn into the TV/VCR. The

TV/VCR will automatically turn on.

Make sure ...

TV/VCR power must be turned on.

•

1 Insert a prerecorded tape

If the erase-protection tab has been removed, the

TV/VCR will start playback automatically.

Window

2 To begin playback

Press the PLAY button.

WRONG

CORRECT

PLAY

Note: If any menu is activated on

the screen, the PLAY button does

not function. Press the MENU but-

ton to clear the menu, then press the

PLAY button.

PRECAUTIONS

Avoid moisture. Moisture condensation may occur

on the tape if it is moved from a cold place to a

warm place or visa versa. Before using a tape with

these conditions, to avoid damage of the tape and

your TV/VCR, wait until the tape has warmed to

room temperature and the moisture has evaporated.

Avoid extreme heat, high humidity and magnetic

fields.

•

3 To stop playback

Press the STOP button when playback is completed.

•

Do not tamper with the cassette mechanism.

Do not touch the tape with your fingers.

•

- 17 -

9I03

Download from Www.Somanuals.com. All Manuals Search And Download.

AUTO REPEAT PLAYBACK

The TV/VCR has an auto repeat function that allows

you to repeat a tape indefinitely without touching the

PLAY button.

ALL REPEAT: Repeat playback from the beginning

to the end of the tape.

PICTURE SEARCH

This feature is very useful in finding or skipping over

a particular scene on a tape. In this mode, the sound

will be muted.

1)You may view a video tape at a high speed in

either a forward or reverse direction by pressing

the F.FWD or REW button during playback (in the

SP / LP / SLP modes).

2)Press it again and the TV/VCR will now search in

super high speed (in the LP / SLP modes only).

NOTE: Tapes recorded in the SP or LP mode will

display a noise bar on the TV screen and the pic-

ture may revert to Black and White. This is normal.

3)Press the PLAY button to return to normal speed.

BLANK REPEAT: Repeat playback from the begin-

ning to a blank part of more than 10 seconds.

1 Select “USER’S SET UP”

– M E N U –

TIMER PROGRAMMING

Press the MENU button on the

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

remote control.

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

Press the PLAY/K or STOP/L but-

ton to point to “USER’S SET UP”.

Then, press the F.FWD/B button.

INDEX SEARCH

ZERO RETURN

This function allows you to search easily a beginning

point that you want to review by rewinding or fast

forwarding.

2 Select “ALL” or “BLANK”

Press the PLAY/K or STOP/L but-

ton to point to “REPEAT PLAY”.

Press the F.FWD/B or REW/s

button repeatedly until your desired

selection [ALL] or [BLANK]

appears.

USER’S SET UP

–

RENTAL

REPEAT PLAY

AUTO RETURN

[OFF]

[ALL]

[OFF]

NOTE:

Zero Return WILL NOT work on a blank tape or a

blank portion of a tape.

1 Stop a tape at your desired point

Rewind or fast forward the tape to the beginning

point from which you want to review.

3 Exit the Repeat Play setting

Press the MENU button on the remote control to

return to the TV mode.

2 Reset the counter to 0:00:00

Press the COUNTER RESET button repeatedly.

4 Start playback

Press the PLAY button to start the Repeat Play.

”REPEAT PLAY B” appears.

3 Begin recording or playback

Press the RECORD or PLAY button.

Press the STOP button when recording or playback is

completed.

Once you select the Repeat Play mode, it stays in

effect even after you turn off the TV/VCR.

If the Rental mode is set [ON], the “RENTAL

PLAY B” display has priority.

•

TO CANCEL THE REPEAT PLAY MODE

4 To activate “ZERO RETURN” mode

– M E N U –

Press the MENU button on the

Repeat steps [1] and [2], select [OFF] using the

F.FWD/B or REW/s button on the remote control.

Press the MENU button on the remote control to

return to TV mode.

If there is a power failure of any kind, the unit

will retain its memory for this feature.

TIMER PROGRAMMING

PICTURE CONTROL

remote control.

Press the PLAY/K or STOP/L but-

ton to point to “ZERO RETURN”.

Then, press the F.FWD/B button.

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

The counter will appear on the TV screen.

The tape will automatically stop when the counter

returns to 0:00:00.

- 18 -

9I03

Download from Www.Somanuals.com. All Manuals Search And Download.

3)Press the F.FWD/B or REW/s button to start

index search. If you want to go forward, press the

F.FWD/B button. If you want to go back, press

the REW/s button.

TIME SEARCH

The Time Search function makes it possible to

quickly advance the tape to your desired position

simply by entering the exact amount of playback

time you want to skip.

After index search, the TV/VCR will play the tape

•

automatically.

In some cases, the index mark at the beginning of

video tape cannot be detected.

NOTES:

•

Time Search can be set up to a maximum of 9

hours 50 minutes (9:50) by 10 minutes at a time.

•

SLOW MOTION

This function will not operate in recording mode.

•

In the example below: To watch a program that is 2

hours, 50 minutes from the present tape position, in

either direction.

Press the SLOW button to reduce the playback speed.

The TV/VCR mutes the sound during slow motion.

Press the PLAY button to return to normal playback.

NOTE: If left in the Slow mode for more than five

minutes, the TV/VCR will automatically go into the

Stop mode.

1 Insert a tape.

2 Select “TIME SEARCH” mode

Press the TIME SEARCH button (with each push it

will increase by 10 minutes).

RENTAL PLAYBACK

This function enables you to improve the picture

quality when playing back worn cassettes such as

rented tapes.

3 Enter your desired time

Press the PLAY/K or STOP/L but-

TIME SEARCH

2 : 50

ton until your desired time appears.

(Example: “2:50” stands for 2

hours 50 minutes)

If you wish to cancel the Time Search at this point,

press the MENU button on the remote control.

1 Select “USER’S SET UP”

– M E N U –

Press the MENU button on the

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

remote control.

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

Press the PLAY/K or STOP/L but-

ton to point to “USER’S SET UP”.

Then, press the F.FWD/B button.

INDEX SEARCH

4 Begin Time Search

By pressing the REW/s or F.FWD/B button, the

TV/VCR will rewind or fast forward to the specified

point.

The time counts down as the searching progresses.

When 0:00 is reached, the tape will start playback

automatically.

USER’S SET UP

–

2 Set “RENTAL” to [ON]

Press the PLAY/K or STOP/L but-

ton to point to “RENTAL”.

Press the F.FWD/B or REW/s

button until [ON] appears.

RENTAL

REPEAT PLAY

AUTO RETURN

[ON]

[OFF]

3 Exit the Rental setting

Press the MENU button on the remote control to

return to the TV mode.

TO CANCEL THE TIME SEARCH at this

point

Press the STOP/EJECT button on the TV/VCR or the

remote control. This will delete the selected time.

4 Start playback

Press the PLAY button to start playback. “RENTAL

PLAY B” appears.

Once you select the Rental mode, it stays in effect

INDEX SEARCH

– M E N U –

An index signal is recorded on the

tape automatically when the record-

ing is started. To view a recording at

a specific start point:

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

•

even after you turn off the TV/VCR.

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

TO CANCEL THE RENTAL MODE

INDEX SEARCH

1)Press the MENU button on the

Repeat steps [1] and [2], select [OFF] using the

F.FWD/B or REW/s button on the remote control.

Press the MENU button on the remote control to

return to TV mode.

If there is a power failure of any kind, the unit

will retain its memory for this feature.

remote control. Press the PLAY/K or STOP/L but-

ton to point to “INDEX SEARCH”, then press the

F.FWD/B button.

2)Press the PLAY/K or STOP/L button within 30

seconds until the number of programs that you

want to skip appears.

- 19 -

9I03

Download from Www.Somanuals.com. All Manuals Search And Download.

VERTICAL HOLD CONTROL

TRACKING ADJUSTMENT

In the Pause/Still mode only, when the picture begins

to vibrate vertically, stabilize the picture by pressing

the CHANNEL K or L button.

Tracking adjustment will be set automatically

(Digital Tracking function) when you start play-

back.

•

NOTE:

However when playing pre-recorded tapes or tapes

recorded on units other than your own, noise lines

(black and white streaks) may appear on the play-

back picture. If this occurs, you can adjust the

tracking control manually by pressing the CHAN-

NEL K or L button until the streaks disappear. To

return to the DTR function, stop the tape once and

start playback again.

You can reduce the noise lines by pressing the

CHANNEL K or L button in slow mode, too.

Tracking adjustment in Slow mode will not be set

automatically.

If there are video noise lines on the screen, see Tracking

Adjustment section.

STILL PICTURE

You can view a still picture on the TV screen during

playback (the Still mode). Press the PAUSE/STILL

button during playback. Only tapes recorded in the

SLP mode will show the least amount of lines. Press

the PLAY button to return to playback.

NOTES:

•

You can advance the picture one frame at a time by

pressing the PAUSE/STILL button during the Still

mode.

If it is left in the Still mode for more than five min-

utes, the TV/VCR will automatically switch to the

Stop mode.

•

NOTE:

In Still mode, press the SLOW button and press the

CHANNEL K or L button until streaks disappear.

To return to Still mode, press the PAUSE/STILL

button again.

•

RECORDING

Make sure ...

Before recording, make sure:

TV/VCR power is turned on.

•

The desired channel is selected by pressing the num-

ber buttons on the remote control or the CHANNEL

Up/Down button. (If the TV/VCR is connected to a

cable box or satellite box, the TV/VCR must be on

CH3 or CH4, then the channel to be recorded is

selected on the cable box or satellite box. )

There is a tape with its safety tab into the VCR.

The desired recording speed is selected in SP(stan-

dard play) or SLP(super long play) mode by press-

ing the TAPE SPEED button on the VCR.

Insert a cassette tape with its erase prevention tab

in place. (If necessary, rewind or fast forward the

tape to the point at which you want to begin

recording.)

NOTE: This unit will ONLY record and view the

same channel.

NORMAL RECORDING

1)Begin the recording by pressing the RECORD but-

ton.

Tape Speed

Type of tape

SP mode

Recording/Playback Time

T60

1 hour

3 hours

T120

T160

To temporarily stop recording or resume it, press

the PAUSE/STILL button. After the VCR has been

in Pause mode for 5 minutes, it will stop automati-

cally to protect the tape and the video head.

NOTES:

2 hours 2-2/3 hours

6 hours 8 hours

SLP mode

ERASE PREVENTION

You can prevent acciden-

tal erasing of recording

by breaking off the tab

on the back edge of the

cassette.

After five minutes, the TV/VCR will automatically

switch to the Recording mode to prevent tape

damage.

If “CLOSED CAPTION (ON)” is selected, the

On-Screen Display will appear for 5 seconds, then

disappear.

•

If you decide to record

on the tape again, cover

the hole with plastic

tape.

•

2)Stop the recording by pressing the STOP button

when recording is completed.

Tab

Plastic Tape

- 20 -

9I03

Download from Www.Somanuals.com. All Manuals Search And Download.

Avoid overlap of programs ...

There is a chance that a program will not be record-

ed. When programs overlap:

OTR (One Touch Recording)

This function enables you to set the recording length

simply by pressing the REC/OTR button on the

VCR.

The program with the earliest start time will record

first.

•

Once the earliest program finishes recording, the

overlapping programs will record in the order of

the program number.

The illustration below demonstrates the sequence

of recording.

•

1)Begin OTR by pressing the

OTR(2 : 30)

REC/OTR button on the VCR

repeatedly until the desired

recording length appears.

•

Recording stops when 0:00 is

reached.

Recording Sequence

NOTES:

Program 1

10:00AM-11:00AM

Program 2

9:00AM-10:00AM

Program 3

This function CANNOT be done from the remote

•

control.

9:30AM-12:00PM

To stop the OTR operation, press the STOP button

on the TV/VCR or on the remote control.

•

9:00AM

10:00AM

11:00AM

12:00PM

*Recording period is SHADED

If the tape runs out before the end time, the

TV/VCR will switch to the Stop mode immediate-

ly, eject the tape and turn itself off.

•

1 Select “TIMER PROGRAMMING”

Press the MENU button on the remote control.

Push(es) Display

Recording length

(continuous recording)

30 minutes

– M E N U –

Confirm “TIMER PROGRAM-

MING” is pointed to by pressing

the PLAY/K button.

1 push

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

2 pushes

3 pushes

4 pushes

0:30

1:00

1:30

60 minutes

90 minutes

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

Press the F.FWD/B button.

ZERO RETURN

TIME SEARCH

INDEX SEARCH

If you have not yet set the clock,

•

“MANUAL CLOCK SET” appears. If so, follow

stops [3] to [8] on page 11. Then set the timer

recording.

17 pushes

8:00

480 minutes

TIMER RECORDING

2 Select your desired program position (1~8)

You may set the TV/VCR to start and end a record-

ing while you are away. You can set 8 programs to

record on specific days, daily or weekly within a 1

year period.

– TIMER PROGRAMMING –

Press the PLAY/K or STOP/L but-

CH DATE

BEGIN END

ton to select the desired program

position.

Then, press the F.FWD/B button.

- - -/- - - - - -:- -

-:- - - -

In the example below, the timer is being set to record:

DATE:

July 5th, 2002

SETTING TIME: from 7:30PM to 8:50PM

3 Set the channel number

Press the PLAY/K or STOP/L but-

ton until the desired channel num-

ber appears.

(Example: CH61)

Then, press the F.FWD/B button.

Remember:

If your TV/VCR is connected to a cable or satellite

box, you must set the TV/VCR to channel 3 or 4 to

match the output channel of the box.

CHANNEL:

TAPE SPEED:

CH61

– TIMER PROGRAMMING –

CH DATE BEGIN END

- - -/- - - - - -:- -

61 -/- - - - - -:- -

- - -/- - - - - -:- -

-:- - - -

Make sure ...

If your TV/VCR is connected to a cable or satellite

box, you must set the TV/VCR to channel 3 or 4

to match the output channel of the box.

Clock is set to the correct time and date before set-

ting the timer.

TV/VCR power is turned on to program it.

To insert a cassette tape with its erase prevention

tab in place. (If necessary, rewind or fast forward

the tape to the point at which you want to begin

recording.)

•

4 Select once, every day or weekly recording

For once recording :

– TIMER PROGRAMMING –

To set the channel you want to record

Press the PLAY/K (up) button

until the desired date appears.

(Example: “7/05” for July 5th).

Then, press the F.FWD/B but-

ton.

CH DATE

BEGIN END

•

- - -/- - - - - -:- -

61 7/05 FRI -:- -

- - -/- - - - - -:- -

-:- - - -

- 21 -

9I03

Download from Www.Somanuals.com. All Manuals Search And Download.

For every day recording : To

record a TV program at the same

time on the same channel every

day. (Example: Monday through

Sunday)

– TIMER PROGRAMMING –

CH DATE BEGIN END

10 Finish setting the program

Press the F.FWD/B or REW/s button. The program

is now completed.

- - -/- - - - - -:- -

61 EVRY DAY -:- -

- - -/- - - - - -:- -

-:- - - -

To set another program, repeat steps [2] to [10].

Press the MENU button on the remote control to

•

Press the STOP/L (down) but-

ton until “EVRY DAY” appears. Then, press the

F.FWD/B button.

return to original mode.

11 Set the timer

Press the POWER button to set automatic timer

recording. The RECORD indicator lights up.

For weekly recording : To record a TV program at

the same time on the same channel every week.

(Example: every Monday)

You must turn off the TV/VCR to activate automat-

ic timer recording.

– TIMER PROGRAMMING –

•

CH DATE

BEGIN END

Press the STOP/L (down) button

until “EVRY” and your desired

day of the week appear together.

Then, press the F.FWD/B but-

ton.

- - -/- - - - - -:- -

61 EVRY MON -:- -

- - -/- - - - - -:- -

-:- - - -

If power is not turned off and you continue watch-

ing TV, “TIMER REC STANDBY” starts flashing

on the TV screen 2 minutes before the programmed

start time.

– TIMER PROGRAMMING –

CH DATE BEGIN END

5 Set beginning hour

TIMER PROGRAM EXTENSION

Press the PLAY/K or STOP/L but-

ton until the desired hour appears.

(Example: “ 7, PM” for 7:30PM)

Then, press the F.FWD/B button.

- - -/- - - - - -:- -

-:- - - -

61 7/05 FRI 7:12^P

- - -/- - - - - -:- -

To shift the time schedule of an automatic timer

recording.

1)Press the POWER button.

2)Repeat step [1] on page 21.

6 Set beginning minute

– TIMER PROGRAMMING –

CH DATE BEGIN END

3)Press the RECORD button and select the desired

program using the PLAY/K or STOP/L button.

4)Press the RECORD button again.

Each additional push will shift forward the

begin/end time for recording by 10 minutes. When

the recording is already in progress, each additional

push will shift forward the end time only. If you

want to cancel while setting, press the

PAUSE/STILL button on the remote control. The

recording time returns to the original time.

NOTE: When you shift forward the time schedule

during recording, the recording speed will automati-

cally be set to the SLP mode.

Press the PLAY/K or STOP/L but-

ton until the desired minute appears.

(Example: “30” for 7:30PM)

- - -/- - - - - -:- -

-:- - - -

61 7/05 FRI 7:30^P

- - -/- - - - - -:- -

Then, press the F.FWD/B button.

– TIMER PROGRAMMING –

CH DATE BEGIN END

7 Set end hour

Press the PLAY/K or STOP/L but-

ton until the desired hour appears.

(Example: “8, PM” for 8:50PM)

Then, press the F.FWD/B button.

- - -/- - - - - -:- -

-:- - - -

8:30^PM - -

-:- - - -

61 7/05 FRI 7:30^P

- - -/- - - - - -:- -

– TIMER PROGRAMMING –

CH DATE BEGIN END

8 Set end minute

5)Press the F.FWD/B or REW/s button to exit the

setting menu. Then press the MENU button on the

remote control to return to original mode.

Press the PLAY/K or STOP/L but-

ton until the desired minute appears.

(Example: “50” for 8:50PM)

Then, press the F.FWD/B button.

- - -/- - - - - -:- -

-:- - - -

8:50^PM- -

-:- - - -

61 7/05 FRI 7:30^P

- - -/- - - - - -:- -

TO CORRECT A PROGRAM

While setting a program; press the REW/s but-

ton to go back one step and enter the correct num-

•

– TIMER PROGRAMMING –

CH DATE BEGIN END

9 Set the tape speed

Press the PLAY/K or STOP/L but-

ton until the desired tape speed

appears. (Example: SP)

bers using the PLAY/K or STOP/L button.

After setting a program;

1)Press the POWER button.

- - -/- - - - - -:- -

-:- - - -

8:50^PMSP

-:- - - -

•

61 7/05 FRI 7:30^P

- - -/- - - - - -:- -

2)Repeat steps [1] - [2] on page 21.

3)Press the F.FWD/B button (or press the REW/s

button to go back one step) until the part you

want to correct begins flashing, then make the

changes pressing the PLAY/K or STOP/L but-

ton.

4)Press the POWER button to set automatic timer

recording.

- 22 -

9I03

Download from Www.Somanuals.com. All Manuals Search And Download.

TO CANCEL AN AUTOMATIC TIMER

RECORDING

USER’S SET UP

–

2 Set “AUTO RETURN” to [ON]

Press the PLAY/K or STOP/L but-

ton to point to “AUTO RETURN”.

Press the F.FWD/B or REW/s

button until [ON] appears. Then,

RENTAL

REPEAT PLAY

AUTO RETURN

[OFF]

[ON]

After setting a program;

1)Press the POWER button.

•

2)Repeat steps [1] ~ [2] under TIMER RECORD-

ING, page 21, and select a program you want to

cancel.

3)Press the T-PROG. CLEAR button.

4)Press the MENU button on the remote control to

return to TV mode.

press the MENU button on the remote control to

return to TV mode.

3 Auto Return will begin

When all the timer recordings are completed, the

TV/VCR will rewind to the beginning of the recorded

While recording is in progress;

1)Press POWER button.

•

program(s).

NOTE:

2)Press the STOP/EJECT button on the TV/VCR.

If you press the POWER button while tape is

rewinding, the Auto Return will stop.

TO CHECK THE BEGIN/END TIME

1)Press the POWER button so that the REC indicator

goes off.

•

2)Press the MENU button on the remote control.

3)Confirm “TIMER PROGRAMMING” is pointed

to.

4 Watch the recorded program

Press the PLAY button.

4)Press the F.FWD/B button. The details of pro-

grams appear on the TV screen.

5)Press the MENU button on the remote control to

return to TV mode.

TO CANCEL THE AUTO RETURN

MODE

Repeat steps [1] and [2], select [OFF] using the

F.FWD/B or REW/s button. Then, press the MENU

button on the remote control to return to TV mode.

If there is a power failure of any kind, the unit

will retain its memory for this feature.

HINTS FOR AUTOMATIC

TIMER RECORDING

Make sure the channel you want to record is prop-

erly set in advance.

•

WAKE UP TIMER

The Wake Up Timer function turns on the TV/VCR

without using the POWER button after a desired

period of time.

It is not necessary to press the RECORD button for

•

timer recording.

Recording begins automatically at the Start time.

If you are recording using a Timer mode, you may

not operate the unit manually.

The erase-prevention tab on the cassette must be in

place (or you must put tape over the hole).

If the erase-prevention tab is removed, the cassette

will be ejected when the POWER button is pressed

to off.

•

NOTES:

•

Use the remote control for this procedure.

Clock must be set to the correct time before setting

•

the timer.

If you want to select [TAPE], you must insert a

cassette tape in the TV/VCR. The tape will start

playback automatically on your desired time.

•

If the tape runs out before the end time, the

TV/VCR will switch to the Stop mode immediate-

ly, and the tape will be ejected.

•

1 Select “WAKE UP TIMER”

Press the WAKE-UP/SLEEP button

on the remote control once, and

confirm “ON/OFF” is pointed.

Press the F.FWD/B or REW/s

button until [ON] appears.

AUTO RETURN

With this feature, after timer recording is finished,

the beginning of the recorded program(s) can be

searched for automatically.

WAKE UP B ON/OFF

[ON]

TIMER

TV/TAPE

TIME

[TV]

[12:00AM]

– M E N U –

1 Select “USER’S SET UP”

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

Press the MENU button on the

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

remote control.

Press the PLAY/K or STOP/L but-

ton to point to “USER’S SET UP”.

Then, press the F.FWD/B button.

INDEX SEARCH

- 23 -

9I03

Download from Www.Somanuals.com. All Manuals Search And Download.

SLEEP TIMER

The Sleep Timer function turns off the TV/VCR

without using the POWER button after a desired

period of time.

2 Select “TV” or “TAPE”

Press the PLAY/K or STOP/L but-

ton until it points to “TV/TAPE”.

Press the F.FWD/B or REW/s

button, and select [TV] or [TAPE].

WAKE UP

TIMER

ON/OFF

B TV/TAPE

TIME

[ON]

[TV]

NOTE:

[12:00AM]

This function does not operate during Recording

•

mode.

3 Set wake up time

1 Select “SLEEP TIMER”

Press the WAKE UP/SLEEP button on the remote

control until “SLEEP TIMER” appears.

Press the PLAY/K or STOP/L but-

ton until it points to “TIME”.

Press the F.FWD/B or REW/s

button until your desired wake up

time appears.

WAKE UP

TIMER

ON/OFF

TV/TAPE

B TIME

[ON]

[TV]

[12:00AM]

2 Set sleep time

Press the PLAY/K, STOP/L,

F.FWD/B or REW/s button until

your desired sleep time appears.

Each additional push will increase (or decrease) the

time by 10 minutes.

SLEEP TIMER [2:00]

Each additional push will increase

4 Exit the Wake Up Timer setting

Press the MENU button on the remote control to

return to TV mode.

the time by 30 minutes up to 120 minutes.

Press the MENU button on the remote control to exit

the Sleep Timer setting.

TO CANCEL THE WAKE UP TIMER

TO CANCEL THE SLEEP TIMER

Press the WAKE-UP/SLEEP button on the remote

control once, and confirm “ON/OFF” is pointed.

Press the F.FWD/B or REW/s button until [OFF]

appears.

Press the WAKE UP/SLEEP button on the remote

control until “SLEEP TIMER” appears.

To view the time left for sleep timer, press the

WAKE-UP/SLEEP button twice, then press the

MENU button on the remote control to exit the sleep

timer setting.

COPYING A VIDEO TAPE

You can make copies of video tapes made by friends

or relatives for your enjoyment.

1)Insert a pre-recorded video cassette into the Source

(Playing) VCR or camcorder.

2)Insert a blank video cassette, or one you want to

record over, into the TV/VCR’s cassette compart-

ment.

3)Press the SPEED button on remote control for the

TV/VCR to select the desired recording speed

(SP/SLP).

WARNING: Unauthorized recordings of

copyrighted video tapes may be an

infringement of copyright laws.

Connect your TV/VCR and a Source (Playing) VCR

using the following diagram.

4)Press the CHANNEL K or L button on the

TV/VCR until “AUX” appears on the screen.

NOTE: “AUX” is found below the lowest numbered

memorized channel. (Example: CH2)

5)Press the RECORD button on the TV/VCR.

6)Begin playback of the tape in the source (Playing)

VCR or camcorder.

[The TV/VCR]

VIDEO AUDIO

NOTE: For best results during copying, use the

TV/VCR’s front panel controls whenever possible.

The remote control might affect the source (Playing)

VCR’s playback operation.

[Ex: Source (playing)

VCR or camcorder]

Audio/Video

adapter cable

AUDIO

(not supplied)

OUT

VIDEO

- 24 -

9I03

Download from Www.Somanuals.com. All Manuals Search And Download.

ON SCREEN DISPLAY

To check the Counter, Clock and Channel number on the TV screen, press the DISPLAY button on the remote

control. Each time you press the DISPLAY button on the remote control, the TV screen will change as follows:

WHEN THE CLOSED CAPTION MODE IS OFF:

Counter mode: After 5 seconds, only

the counter remains. To clear it, press

the DISPLAY button.

Clock mode: After 5 seconds, only

the clock and the channel number

remain. To clear them, press the DIS-

PLAY button.

•

5:40PM

CH2

Press

once

Press

once

COUNT 0:12:34

Press once

OFF mode

Clock/Counter mode

WHEN THE CLOSED CAPTION MODE IS ON:

The On Screen Display disappears after 5 seconds.

•

STOP

5:40 PM

CH2

This is true even if the MUTE button is pressed, or the

PAUSE/STILL button is pressed while recording.

COUNT 0:12:34

SPECIAL FEATURES

REAL TIME TAPE COUNTER

AUTO REWIND-EJECT

This shows the elapsed recording or playback time in

When the end of a tape is reached during record-

ing, playback, or fast-forward, the tape will auto-

matically rewind to the beginning. After rewinding

finishes, the TV/VCR will eject the tape and turn

itself to off.

This function is operative when Repeat Play is set

to the [OFF] position.

•

hours, minutes, and seconds. (The displayed time

will not change on a blank tape or blank portions on

the tape.)The “–” indication will appear when the

tape has rewound further than “0:00:00” on the tape

counter.

•

The tape will not auto-rewind during timer record-

ing or One Touch Recording.

MAINTENANCE

back, the video heads in your TV/VCR may need

to be cleaned.

CABINET CLEANING

Wipe the front panel and other exterior surfaces of

the TV/VCR with a soft cloth immersed in luke-

warm water and wrung dry.

•

1.Please visit your local Audio/Video store and pur-

chase a good quality VHS Video Head Cleaner.

2.If a Video Head Cleaner does not solve the prob-

lem, please call our help line at 1-800-968-3429, to

locate an Authorized Service Center.

NOTES:

Remember to read the instructions included with

the video head cleaner before use.

Clean video heads only when problems occur.

Never use a solvent or alcohol. Do not spray insec-

•

ticide liquid near the TV/VCR. Such chemicals

may cause damage and discoloration to the

exposed surfaces.

•

AUTO HEAD CLEANING

•

Automatically cleans video heads as you insert or

remove a cassette, so you can see a clear picture.

•

SERVICING

Should your TV/VCR become inoperative, do not

try to correct the problem by yourself. There are no

user-serviceable parts inside. Turn off, unplug the

power cord, and please call our help line at 1-800-

968-3429, to locate an Authorized Service Center.

Playback picture may become blurred or interrupt-

•

ed while the TV program reception is clear. Dirt

accumulated on the video heads after long periods

of use, or the usage of rental or worn tapes can

cause this problem.

If a streaky or snowy picture appears during play-

- 25 -

9I03

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING GUIDE

If you have followed the instructions contained in this manual and have difficulty in operating your TV/VCR,

locate the PROBLEM in the left column below. Check the corresponding CORRECTIVE ACTION column to

remedy the problem.

PROBLEM

CORRECTIVE ACTION

Make sure the AC cord is connected to an AC outlet.

Make sure the power is turned on.

Make sure the AC cord is connected to an AC outlet.

Check antenna connection.

Let the TV/VCR program its tuner memory.

Adjust direction or replace antenna.

Adjust picture controls.

Adjust volume control on remote control or main unit.

Press the MUTE button to restore sound.

Make sure the timer recording is set correctly.

Make sure the power is off.

Make sure the TV/VCR clock is set correctly.

Make sure the tape has an erase-prevention tab. If need, cover the

hole with plastic tape.

No power.

•

No picture and sound.

No picture or poor picture on

TV/VCR.

No sound or poor sound.

•

Timer recording is not possible.

Cannot go into Record mode.

•

Playback picture is partially noisy.

Adjust tracking control for a better picture using the CHANNEL

or L button on the TV/VCR.

Head cleaning may be necessary. Refer to “AUTO HEAD

CLEANING” on page 25.

•

No picture but the audio is OK in

playback.

•

No operation by infrared Remote

Control.

Video or color fades in and out

Make sure the AC cord is connected to an AC outlet.

Check batteries in remote control.

You can not copy a copyrighted video tape. You are experiencing

copy guard protection.

•

when making a copy of a video tape

CLOSED CAPTION PROBLEM

My TV/VCR is showing captions

that are misspelled.

POSSIBLE REMEDY

• You are watching a live broadcast and spelling errors made by the

• closed captioning production company may pass through uncorrected.

• A prerecorded program will not show any misspelled words because

• of the normal time available for editing the captions.

My TV/VCR will not show the text • Captions that are delayed a few seconds behind the actual dialogue

in its entirety or there is a delay of • are common for live broadcast. Most captioning production companies

what is being said.

• can display a dialogue to a maximum of 220 words per minute. If a

• dialogue exceeds that rate, selective editing is used to insure that the

• captions remain up-to-date with the current TV screen dialogue.

• Interference caused by building, power lines, thunderstorms, etc.

• may cause scrambled or incomplete captions to appear.

My captions are scrambled with

white boxes on the TV screen.

My program guide listed a TV show • Broadcasters may at times use a time compression process to speed

as being closed captioned but none • up the actual program so that additional advertising time can be

of the captions were displayed.

• given. Since the decoder cannot read the compressed information,

• captions will be lost.

My prerecorded video tape does not • The video tape was either an illegal copy or the tape duplicating

show any captions. The tape box • company accidentally left out the captioning signals during the

mentions it being closed captioned. • copying process.

My TV screen shows a black box

on certain channels.

• You are in the TEXT mode. Select CAPTION mode to CAPTION

• [OFF].

- 26 -

9I03

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIFICATIONS

GENERAL SPECIFICATIONS

ELECTRICAL SPECIFICATIONS

CRT :

13 or 19 inch in-line gun, 90˚

deflection tube

NTSC-M

Video input level :

Audio input level :

0.5~2.0Vp-p

-15dBs

Television system :

Closed caption system :§15.119/FCC

Video S/N ratio : More than 46dB

Audio S/N ratio : More than 43dB

Video Heads :

Tape width :

Tape speed

SP :

LP :

SLP :

Tuner channel

TV VHF Low :

TV VHF High :

TV UHF :

CATV

Rotary four-head

1/2 inch

OTHER SPECIFICATIONS

[ 63134C ]

Power requirement : AC 120V/60Hz

Power consumption : 65W

33.40mm/sec.

16.67mm/sec.

11.12mm/sec.

Dimensions :

H:15-3/8” (389mm)

W:14-1/2” (367mm)

D:14-7/8” (377mm)

23.1 lbs (10.5kg)

#2~#6

#7~#13

#14~#69

Weight :

[ 63194C ]

Power requirement : AC 120V/60Hz

Power consumption : 80W

VHF :

MID band :

SUPER band :

HYPER band :

Terminals

A5~A1, A~I

J~W

W+1~W+84

Dimensions :

H:19-1/2” (493mm)

W:19-3/8” (491mm)

D:18-3/4” (475mm)

43.0 lbs (19.5kg)

Weight :

Antenna input :

VHF/UHF 75 ohms

unbalanced

RCA connector [ 1

1/8” monaural (3.5 mm)

Designs and specifications are subject to change

without notice.

If there is a discrepancy between languages, the

default language will be English.

•

Video input :

Audio input :

Earphone :

CABLE CHANNEL DESIGNATIONS

If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels

with letters or letter-number combinations. Please check with your local cable company. The following is a

chart of common cable channel designations.

CATV channel

TV Display

CATV channel

TV Display

CATV channel

W+1

W+2

W+3

W+4

W+5

W+6

W+7

W+8

W+9

TV Display

CATV channel

W+10 W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24

46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

W+25 W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39

61 62 63 64 65 66 67 68 69 70 71 72 73 74 75

W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54

TV Display

CATV channel

TV Display

CATV channel

TV Display

W+59 W+60 W+61 W+62 W+63 W+64

100 101 102 103 104 105

W+55 W+56 W+57 W+58

A-5

A-4

A-3

A-2

A-1

CATV channel

TV Display

CATV channel

W+65 W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79

TV Display

106

W+80 W+81 W+82 W+83 W+84

121 122 123 124 125

107

108

109

110

111

112

113

114

115

116

117

118

119

120

CATV channel

TV Display

- 27 -

9I03

Download from Www.Somanuals.com. All Manuals Search And Download.

INDICE

CONTROLES DE OPERACIÓN Y

SUS FUNCIONES . . . . . . . . . . . . . . . . . . . . . . . .28

INSTALACIÓN DE LAS PILAS . . . . . . . . . . . . .31

PREPARACIÓN DE CANALES POR

CONEXIONES DE ANTENA/CABLE . . . . . . . .30 PRIMERA VEZ . . . . . . . . . . . . . . . . . . . . . . . . . .31

MODO DE ENTRADA EXTERNA . . . . . . . . . . .31 AJUSTE DEL RELOJ . . . . . . . . . . . . . . . . . . . . .31

CONTROLES DE OPERACIÓN Y SUS FUNCIONES

Este manual sirve para los modelos de 13" y 19". A excepción de la apariencia, la operación de los dos modelos es exac-

tamente la misma. En este manual se muestra el modelo de 19".

NOTA:

No recomendamos utilizar mandos a distancia universales. No todas las funciones pueden ser controladas mediante un

mando a distancia universal. Si decide utilizar un mando a distancia universal con esta unidad, tenga en cuenta que con el

número de código dado tal vez no se pueda controlar la unidad. En este caso, póngase en contacto con el fabricante del

mando a distancia universal.

- PANEL DELANTERO -

VIDEO AUDIO

POWER

CHANNEL

STOP/EJECT

REW PLAY F.FWD

REC/OTR EARPHONE

VOLUME

1 2 3 4 5 6 7 8 9101112

1 Toma de entrada de vídeo (VIDEO)– Conéctela a

la toma de salida de vídeo de su videocámara u otra

videograbadora.

2 Toma de entrada de audio (AUDIO)– Conéctela a

la toma de salida de audio de su equipo de audio,

videocámara u otra videograbadora.

3 Botón de la alimentación (POWER)– Púlselo para

encender y apagar el televisor/videograbadora. Púlselo

para activar la grabación con temporizador.

4 Botones de volumen (VOLUME X / Y)– Ajustan

el nivel del volumen.

5 Botones de canales (CHANNEL K/ L)– Púlselos

para seleccionar los canales deseados para ver o grabar.

6 Ventanilla sensora del mando a distancia–

Recibe las señales infrarrojas procedentes del mando a

distancia.

7 Botón de parada (STOP)– Púlselo para detener la

cinta.

Botón de expulsión (EJECT)–Púlselo en el modo

de parada para expulsar la cinta del

televisor/videograbadora.

- CONTROL REMOTO -

WAKE-UP

POWER

/SLEEP

EJECT

CHANNEL

RETURN

CHANNEL

VOLUME

+100

DISPLAY

MUTE

PLAY

REW

F.FWD

STOP

RECORD

SPEED PAUSE/STILL

T-PROG.

CLEAR

GAME

SLOW

COUNTER

RESET

Botón L–

Púlselo para seleccionar los modos de ajuste desde el

menúde la pantalla.

Púlselo para introducir dígitos cuando establezca un

programa.

•

(Por ejemplo: Para ajustar el reloj o establecer un pro-

grama de temporizador)

- 28 -

0I29

Download from Www.Somanuals.com. All Manuals Search And Download.

- PANEL TRASERO -

ANT.

minimizar el ruido de vídeo (líneas o puntos en la pan

talla) durante la reproducción.

8 Botón de rebobinado (REW)– Púlselo para

rebobinar la cinta, o para ver la imagen en retroceso

rápido durante el modo de reproducción. (Búsqueda

con rebobinado)

14 Compartimiento del videocasete

15 Botones numerados– Púlselos para seleccionar los

canales deseados para ver o grabar. Para seleccionar

canales del 1 al 9, pulse primero el botón 0 y luego el

botón 1 a 9.

Botón s–

Púlselo para seleccionar un modo desde un menúpar-

ticular.

•

Botón +100– Cuando seleccione canales de tele-

visión por cable cuyo número sea superior al 99, pulse

primero este botón, y luego pulse los dos últimos dígi-

tos. (Para seleccionar el canal 125, pulse primero el

botón “+100” y luego el “2” y el “5”.)

(Por ejemplo: IDIOMA o ADJUST DE USER)

9 Botón de reproducción (PLAY)– Púlselo para ini-

ciar la reproducción.

Botón K–

Púlselo para seleccionar los modos de ajuste desde el

menúde la pantalla.

Púlselo para introducir dígitos cuando establezca un

programa.

(Por ejemplo: Para ajustar el reloj o establecer un pro-

grama de temporizador)

•

16 Botón de menú (MENU)– Púlselo para visualizar el

menúprincipal en la pantalla del televisor.

17 Botón del visualizador (DISPLAY)– Visualiza el

contador o el número del canal actual y la hora actual

en la pantalla del televisor.

18 Botón de velocidad de cinta (SPEED)– Púlselo

10 Botón de avance rápido (F.FWD)– Púlselo para

avanzar rápidamente la cinta, o para ver la imagen en

avance rápido durante el modo de reproducción.

(Búsqueda con avance rápido)

para elegir la velocidad de grabación deseada: SP/SLP.

19 Botón T-PROG. CLEAR– Púlselo para cancelar un

programa de temporizador.

Botón de reposición del contador (COUNTER

RESET)– Púlselo para reponer el contador a 0:00:00.

Botón B–

Cuando establezca un programa (por ejemplo: para

ajustar el reloj o para establecer un programa de tem-

porizador), púlselo para determinar su elección y vaya

al paso siguiente que quiera introducir.

Púlselo para determinar los modos de ajuste desde el

menúde la pantalla.

Púlselo para seleccionar un modo desde un menúpar-

ticular.

(Por ejemplo: IDIOMA o ADJUST DE USER)

•

20 Botón de juego (GAME)– Establece el modo del

juego y el modo de entrada externa al mismo tiempo.

21 Botón de cámera lenta (SLOW)– Pulselo para

activar la reproducción a cámera lenta.

•

22 Botón de pausa/imagen fija (PAUSE/STILL)–

Púlselo para detener temporalmente la cinta durante la

grabación o para ver una imagen fija durante la repro-

ducción.

23 Botón de silenciamiento (MUTE)– Silencia el

11 Botón de grabación (REC)– Púlselo para iniciar la

sonido. Púlselo de nuevo para recuperar el sonido.

grabación manual.

24 Botón de retorno de canal (CHANNEL

RETURN)– Púlselo para volver al canal anterior. Por

ejemplo, pulsando una vez este botón, la visualización

del canal cambiará de 3 (canal actual) a 10 (canal ante-

rior), y al pulsarlo por segunda vez, el canal cambiará

del 10 al 3.

25 Botón del temporizador despertador/para

dormir (WAKE-UP/SLEEP)– Ajusta el tempo-

rizador para despertarse/dormir.

Botón de grabación de un toque (OTR)– Activa

la grabación de un toque. (Sólo en el

televisor/videograbadora)

12 Indicador de grabación (RECORD)– Parpadea

durante la grabación.

Se enciende en el modo de espera de la grabación con

temporizador.

13 Toma de auriculares (EARPHONE)– Para conec-

tar los auriculares (no suministrados) y escuchar en

privado. La toma es mono y tiene un tamaño de 3,5

mm.

26 Botón de expulsión (EJECT)–Púlselo en el modo

de parada para expulsar la cinta del

televisor/videograbadora.

Se puede mostrar el menú principal en la pantalla del

televisor pulsando repetidamente este botón del televi-

sor/videograbadora.

27 Cordón de alimentación– Conéctelo a la toma de

CA estándar (120V/60Hz).

28 Terminal de antena (ANT.)– Para conectar una

Función de seguimiento– Pulse los botones para

antena o sistema de televisión por cable.

- 29 -

0I29

Download from Www.Somanuals.com. All Manuals Search And Download.

CONEXIONES DE ANTENA/CABLE

Desde el cable coaxial o

caja de emisiones vía

satélite de 75 ohm del

sistema de Cable

Caja de CATV

o caja de emi-

siones vía satélite

(no incluído)

Antena combinada de

VHF/UHF

(no incluído)

Antena de varilla UHF/VHF

(incluído para solamente 13”)

OUT

Antena VHF

(no incluído)

Desde el

sistema de Cable

Antena UHF

(no incluído)

Combinador de

VHF/UHF

(no incluído)

ANT.

Cable coaxial

de 75 ohm (no incluído)

CABLE CON CONVERTIDOR/DESCODIFICADOR

O CONVERTIDOR DE EMISIONES VÍA SATÉLITE

Si su servicio de televisión por cable le suministra un con-

vertidor, o si usted utiliza un sistema de emisiones vía

satélite, usted podrá utilizar las conexiones básicas.

Utilizando estas conexiones, usted también podrá grabar

canales codificados. Sin embargo, la selección de los

canales deberá hacerse con el convertidor de televisión por

cable con el convertidor de emisiones vía satélite. Esto sig-

nifica que los canales no podrán ser cambiados con el

mando a distancia del televisor/videograbadora. La

grabación inatendida se limita a un canal cada vez.

ANTENA COMBINADA DE VHF/UHF

La antena de varilla de VHF/UHF (incluído para solamente

13”) es desmontable. Inserte el vástago de la antena en el

agujero de la parte trasera superior del

televisor/videograbadora.

Conecte la varilla de antena de VHF/UHF o la antena com-

binada de VHF/UHF al terminal ANT. del

televisor/videograbadora.

ANTENAS SEPARADAS DE VHF/UHF

En algunos lugares será necesario utilizar una antena exte-

rior.

PARA GRABAR UN CANAL

CODIFICADO/DESCODIFICADO

CABLE SIN CONVERTIDOR/DESCODIFICADOR

1. Ajuste el selector de canales del televisor/videograbado-

ra al canal de salida del convertidor de televisión por

cable o del convertidor de emisiones vía satélite. (Ej.:

CA3)

2. Seleccione el canal que desee grabar de su convertidor

de televisión por cable o del convertidor de emisiones

vía satélite.

Utilice esta conexión si su sistema de televisión por cable

se conecta directamente a su televisor/videograbadora sin

convertidor.Utilizando esta conexión usted podrá:

1)Utilizar el mando a distancia del televisor/videograbado-

ra para seleccionar canales.

2)Programar uno o más canales sin codificar para realizar

la grabación automática con temporizador.

NOTA: Con esta unidad SÓLO se podrá grabar y ver un

mismo canal al mismo tiempo.

- 30 -

0I29

Download from Www.Somanuals.com. All Manuals Search And Download.

MODO DE ENTRADA EXTERNA

AJUSTE DEL RELOJ

Cerciórese...

Cuando utilice una señal de entrada externa (otra

videograbadora o una videocámara), conecte los cables de

salida de audio/vídeo del equipo de reproducción a las

tomas AUDIO IN/VIDEO IN de su

televisor/videograbadora. Y luego pulse el botón CHAN-

NEL K o L hasta que “AUX” aparezca en la pantalla.

La alimentación del televisor/videograbadora deberá

•

estar conectada.

En el ejemplo de abajo, el reloj va a ajustarse así:

FECHA: 7 de mayo de 2002

HORA: 5:40 PM

1) Pulse el botón MENU en el mando a distancia.

Pulse el botón PLAY/K o STOP/L para indicar

“AJUSTE RELOJ”.

Usted puede programar el temporizador para que explore

todos los canales que puedan recibirse en su zona.

Luego, pulse el botón F.FWD/B.

INSTALACIÓN DE LAS PILAS

2) Pulse el botón PLAY/K o STOP/L para indicar

“AJUSTE MANUAL RELOJ”.

1)Abra la tapa del compartimiento de las pilas del mando

a distancia presionándola en el sentido de la flecha.

2)Inserte 2 pilas tamaño “AA” en el compartimiento de las

pilas, en el sentido indicado por las marcas de polaridad

(+/-).

Luego, pulse el botón F.FWD/B.

3) Pulse el botón PLAY/K o STOP/L hasta que aparezca

el mes deseado. (Ejemplo: Mayo - 05)

Luego, pulse el botón F.FWD/B.

4) Pulse el botón PLAY/K o STOP/L hasta que aparezca

el día del mes deseado. (Ejemplo: 7 - 07)

3)Vuelva a poner la tapa.

Luego, pulse el botón F.FWD/B.

5) Pulse el botón PLAY/K o STOP/L hasta que aparezca

el año deseado. (Ejemplo: 2002)

Luego, pulse el botón F.FWD/B.

6) Pulse el botón PLAY/K o STOP/L hasta que aparezca

la hora deseada. (Ejemplo: 5, PM)

Luego, pulse el botón F.FWD/B.

7) Pulse el botón PLAY/K o STOP/L hasta que aparezca

el minuto deseado. (Ejemplo: 40)

PREPARACIÓN DE CANALES POR

PRIMERA VEZ

8) Pulse el botón MENU en el mando a distancia. Aunque

los segundos no se visualizan, éstos empiezan a contar

desde 00 cuando se pulsa MENU en el mando a distan-

cia. Utilice esta función para sincronizar el reloj con la

hora correcta.

1) Enchufe el cable de alimentación del

televisor/videograbadora en una toma de CA estándar.

NOTA: Si aparezcan algunos digitos en el rincón de la

pantalla, pulse el botón POWER sin desenchufar el cable

de alimentación.

2) Pulse el botón POWER para encender el

televisor/videograbadora.

3) Seleccione “ENGLISH” o “ESPAÑOL” utilizando el

botón F.FWD/B o REW/s. “[ ]” indica el idioma

seleccionado.

4) Pulse el botón PLAY/K o STOP/L para señalar

“AUTOPRESELECCION”.

Luego pulse el botón F.FWD/B. El sintonizador explo-

rará y memorizará todos los canales activos de su área.

NOTAS:

El televisor/videograbadora distingue entre los canales

de televisión estándar y los canales de televisor por

cable.

•

Si desea reproducir o grabar una cinta ANTES de prea-

justar el sintonizador, usted tendrá que pulsar el botón

MENU en el mando a distancia. Para preajustar de

nuevo el sintonizador, consulte “REPETICIÓN DE LA

PREPARACIÓN DE CANALES”.

•

La unidad de televisor/videograbadora puede reconocer

los canales de TV como ellos de TV por cable a causa

de los condiciones de recepción. En este caso, pruebe el

preajuste automático de nuevo en los condiciones finas

de recepción.

•

5) El sintonizador se para en el canal memorizado más

bajo. Si desea recuperar canales seleccionados, usted

podrá seleccionar directamente el canal deseado con los

botones numerados del mando a distancia o con los

botones CHANNEL K o L.

- 31 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LIMITED WARRANTY

FUNAI CORP. will repair this SYLVANIA product, free of charge in the USA in the event of defect in materials

or workmanship as follows:

DURATION:

PARTS:

FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from

the date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded

from this warranty.

LABOR:

FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date

of original retail purchase.

LIMITS AND EXCLUSIONS:

This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail

purchase will be required together with the product to obtain service under this warranty.

This warranty shall not be extended to any other person or transferee.

This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing

or if service was attempted by an unauthorized service center. This FUNAI CORPORATION Limited warranty

does not apply to any product not purchased and used in the United States.

This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It

does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product

not supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplica-

tion, alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this

product or damage which results from fire, flood, lightning or other acts of God.

THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE

CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.

FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY

GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE

USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL

OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF

FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY, AND FIT-

NESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS REPRESENTA-

TIVES IN THE UNITED STATES.

ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY A FUNAI AUTHORIZED

SERVICE CENTER. THIS WARRANTY IS VALID WHEN THE UNIT IS TAKEN TO A FUNAI AUTHO-

RIZED SERVICE FACILITY.

IMPORTANT:

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS

THAT VARY FROM STATE TO STATE, IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE

UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT

FUNAI CORP.

ATTENTION:

FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT WITH-

OUT PRIOR NOTICE.

To locate your nearest SYLVANIA Authorized Service Center or for general service procedure,

please call 1-800-968-3429 or write to the following:

FUNAI CORPORATION, INC.

Customer Service

100 North Street; Teterboro, NJ 07608

Tel :1-800-968-3429

PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.

Printed in Malaysia

0EMN01975

T5314 / 7314UQ * * * * *

Download from Www.Somanuals.com. All Manuals Search And Download.

Soleus Air Air Conditioner SG TTW 12ESE User Manual
Sony CRT Television KV 32S40 User Manual
Sony Digital Camera VF 30PK S User Manual
Sony Headphones MDR EX71SL User Manual
Sony Stereo System CMT HX70BTR User Manual
SpectraLink Cordless Telephone JPI300 User Manual
StarTechcom Stereo Receiver VGA2HD2 User Manual
State Industries Water Heater SRGSS02207 User Manual
Stiga Lawn Mower 8211 0229 06 User Manual
Sunrise Medical Mobility Aid S 646 User Manual