Sylvania TV DVD Combo SRTD420 User Manual

OWNER’S

MANUAL

COLOR TV/DVD

SRTD420 (20 inch)

SUPPLIED ACCESSORIES

Remote Control Unit

Batteries

Owner’s Manual

Owner's Manual

INSTRUCCIONES

EN ESPAÑOL INCLUIDAS.

NE226UD

2 AA Batteries

0EMN02492

As an ENERGY STAR^®

Partner, our company has

determined that this product meets

the ENERGY STAR^®guidelines for

energy efficiency. ENERGY STAR^®

is a U.S. registered mark.

If you need additional operating assistance after reading this

owner’s manual, please call

TOLL FREE : 1-800-968-3429.

Download from Www.Somanuals.com. All Manuals Search And Download.

Please read before using this equipment

FIGURE A

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

ANTENNA

LEAD I N

WI RE

GROUND

CL AMP

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

ELECTRI C

SERVICE

EQUIPMENT

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

NEC

NATIONAL ELECTRICAL CODE

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

S2898A

12.Power-Cord Protection-Power-supply cords should be

routed so that they are not likely to be walked on or

pinched by items placed upon or against them, paying par-

ticular attention to cords at plugs, convenience receptacles,

and the point where they exit from the appliance.

19.Damage Requiring Service-Unplug this TV/DVD from

the wall outlet and refer servicing to qualified service per-

sonnel under the following conditions:

a. When the power-supply cord or plug is damaged or frayed.

b. If liquid has been spilled, or objects have fallen into the

TV/DVD.

13.Outdoor Antenna grounding-If an outside antenna or

cable system is connected to the TV/DVD, be sure the

antenna or cable system is grounded so as to provide some

protection against voltage surges and built-up static

charges. Article 810 of the National Electrical Code,

ANSI/NFPA No. 70, provides information with respect to

proper grounding of the mast and supporting structure,

grounding of the lead-in wire to an antenna discharge unit,

size of grounding conductors, location of antenna-discharge

unit, connection to grounding electrodes, and requirements

for the grounding electrode. (Fig. A)

c. If the TV/DVD has been exposed to rain or water.

d. If the TV/DVD does not operate normally by following the

operating instructions. Adjust only those controls that are

covered by the operating instructions, as improper adjust-

ment of other controls may result in damage and will often

require extensive work by a qualified technician to restore

the TV/DVD to its normal operation.

e. If the TV/DVD has been dropped or damaged in any way.

f. When the TV/DVD exhibits a distinct change in perfor-

mance-this indicates a need for service.

14.Lightning-For added protection for this TV/DVD receiver

during a lightning storm, or when it is left unattended and

unused for long periods of time, unplug it from the wall

outlet and disconnect the antenna or cable system. This will

prevent damage to the TV/DVD due to lightning and

power-line surges.

20.Replacement Parts-When replacement parts are required,

be sure the service technician has used replacement parts

specified by the manufacturer that have the same character-

istics as the original part. Unauthorized substitutions may

result in fire, electric shock, injury to persons or other haz-

ards.

15.Power Lines-An outside antenna system should not be

located in the vicinity of overhead power lines or other

electric light or power circuits, or where it can fall into

such power lines or circuits. When installing an outside

antenna system, extreme care should be taken to keep from

touching such power lines or circuits as contact with them

might be fatal.

21.Safety Check-Upon completion of any service or repairs to

this TV/DVD, ask the service technician to perform routine

safety checks to determine that the TV/DVD is in proper

operating condition.

22.Heat-This TV/DVD product should be situated away from

heat sources such as radiators, heat registers, stoves, or

other products (including amplifiers) that produce heat.

16.Overloading-Do not overload wall outlets and extension

cords as this can result in a risk of fire or electric shock.

17.Object and Liquid Entry-Never push objects of any kind

into this TV/DVD through openings as they may touch dan-

gerous voltage points or short out parts that could result in

a fire or electric shock. Never spill liquid of any kind on

the TV/DVD.

18.Servicing-Do not attempt to service this TV/DVD yourself

as opening or removing covers may expose you to danger-

ous voltage or other hazards. Refer all servicing to qualified

service personnel.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

PRECAUTIONS

LASER SAFETY

IMPORTANT COPYRIGHT INFORMATION

Unauthorized copying, broadcasting, public perfor-

mance and lending of discs are prohibited.

This unit employs a laser. Only a qualified service

person should remove the cover or attempt to ser-

vice this device, due to possible eye injury.

This product incorporates copyright protection tech-

nology that is protected by method claims of certain

U.S. patents and other intellectual property rights

owned by Macrovision Corporation and other rights

owners. Use of this copyright protection technology

must be authorized by Macrovision Corporation,

and is intended for home and other limited viewing

uses only unless otherwise authorized by

CAUTION: USE OF CONTROLS OR ADJUST-

MENTS OR PERFORMANCE OF PROCE-

DURES OTHER THAN THOSE SPECIFIED

HEREIN MAY RESULT IN HAZARDOUS

RADIATION EXPOSURE.

Macrovision Corporation. Reverse engineering or

disassembly is prohibited.

CAUTION: VISIBLE AND INVISIBLE LASER

RADIATION WHEN OPEN AND INTERLOCK

DEFEATED. DO NOT STARE INTO BEAM.

LOCATION: INSIDE, NEAR THE DECK

MECHANISM.

FCC WARNING- This equipment may gener-

ate or use radio frequency energy. Changes or

modifications to this equipment may cause

harmful interference unless the modifications

are expressly approved in the instruction man-

ual. The user could lose the authority to oper-

ate this equipment if an unauthorized change

or modification is made.

This Class B digital apparatus complies with

Canadian ICES-003.

Cet appareil numérique de la classe B est con-

forme à la norme NMB-003 du Canada.

RADIO-TV INTERFERENCE

This equipment has been tested and found to com-

ply with the limits for a Class B digital device, pur-

suant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and

used in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to

radio or television reception, which can be deter-

mined by turning the equipment off and on, the

user is encouraged to try to correct the interfer-

ence by one or more of the following measures:

1) Reorient or relocate the receiving antenna.

2) Increase the separation between the equipment

and receiver.

CAUTION: TO PREVENT ELECTRIC SHOCK,

MATCH WIDE BLADE OF PLUG TO WIDE

SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOCS

ÉLECTRIQUES, INTRODUIRE LA LAME LA

PLUS LARGE DE LA FICHE DANS LA

BORNE CORRESPONDANTE DE LA PRISE

ET POUSSER JUSQU’AU FOND.

A NOTE ABOUT RECYCLING

This product’s packaging materials are recyclable

and can be reused. Please dispose of any materials

in accordance with your local recycling regulations.

Batteries should never be thrown away or incinerat-

ed but disposed of in accordance with your local

regulations concerning chemical wastes.

3) Connect the equipment into an outlet on a cir-

cuit different from that to which the receiver is

connected.

4) Consult the dealer or an experienced radio/TV

technician for help.

The serial number of this product may be found on the back of the unit. No other TV/DVD has the same serial

number as yours. You should record the number and other vital information here and retain this book as a per-

manent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.

Date of Purchase

Dealer Purchase from

Dealer Address

Dealer Phone No.

Model No.

Serial No.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

LOCATION

SYMBOLS USED IN THIS MANUAL

The following symbols below appear in some head-

ings and notes in this manual, with the following

meanings

For safe operation and satisfactory performance of

your TV/DVD, keep the following in mind when

selecting a place for its installation:

Shield it from direct sunlight and keep it away from

sources of intense heat.

•

: Description refers to TV operation (in the TV mode).

Avoid dusty or humid places.

Avoid places with insufficient ventilation for proper

heat dissipation. Do not block the ventilation holes at

the top and bottom of the unit. Do not place the unit

on a carpet because this will block the ventilation

holes.

Install unit in a horizontal position.

Avoid locations subject to strong vibration.

Do not place the TV/DVD near strong magnetic fields.

Avoid moving TV/DVD to locations where temper-

•

DVD-V

•

: Description refers to playback of DVD video discs

(in the DVD mode).

: Description refers to playback of audio CDs

(in the DVD mode).

•

MP3

•

: Description refers to playback of MP3 discs

(in the DVD mode).

•

QUICK

ature differences are extreme.

: Description refers to the items to be set by the

QUICK mode (in the DVD mode).

AVOID THE HAZARDS OF

ELECTRICAL SHOCK AND FIRE

Do not handle the power cord with wet hands.

Do not pull on the power cord when disconnecting

it from an AC wall outlet. Grasp it by the plug.

•

If, by accident, water is spilled on your unit, unplug

the power cord immediately and take the unit to an

Authorized Service Center for servicing.

•

Do not put your fingers or objects into the

TV/DVD disc loading tray.

•

Do not place anything directly on top of the unit.

•

WARNING

Moisture condensation may occur inside the unit

when it is moved from a cold place to a warm place,

or after heating a cold room or under conditions of

high humidity. If a DVD is played in a TV/DVD

which has moisture, it may damage the DVD and

TV/DVD. Therefore when the condensation occurs

inside the unit, turn POWER on and allow at least 2

hours for the unit to dry out.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

TABLE OF CONTENTS

C IMPORTANT SAFEGUARDS . . . . . . . . . . . . .2

C SEARCH FUNCTION . . . . . . . . . . . . . . . . . .22

TRACK SEARCH . . . . . . . . . . . . . . . . . . . . . .22

TITLE / CHAPTER SEARCH . . . . . . . . . . . . .22

TIME SEARCH . . . . . . . . . . . . . . . . . . . . . . . .22

MARKER SETUP SCREEN . . . . . . . . . . . . . .22

C PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . .4

LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

AVOID THE HAZARDS OF ELECTRICAL

SHOCK AND FIRE . . . . . . . . . . . . . . . . . . . . . .5

WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

SYMBOLS USED IN THIS MANUAL . . . . . . .5

C SPECIAL PLAYBACK FUNCTION . . . . . . . .23

REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

PROGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . .23

RANDOM PLAYBACK . . . . . . . . . . . . . . . . .23

C TABLE OF CONTENTS . . . . . . . . . . . . . . . . . .6

C FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

C PLAYING A MP3 DISC . . . . . . . . . . . . . . . . . .24

MP3 PLAYBACK . . . . . . . . . . . . . . . . . . . . . .24

REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

PROGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . .24

RANDOM PLAYBACK . . . . . . . . . . . . . . . . .24

OPERATING CONTROLS AND FUNCTIONS . . .8

INSTALLING THE BATTERIES . . . . . . . . . . .9

C PREPARATION FOR USE . . . . . . . . . . . . . . .10

ANTENNA/CABLE CONNECTIONS . . . . . . .10

CONNECTING TO FRONT A/V INPUT JACKS . .11

C CHANGING THE SETTINGS . . . . . . . . . . . .25

SUBTITLE LANGUAGE . . . . . . . . . . . . . . . .25

AUDIO LANGUAGE . . . . . . . . . . . . . . . . . . .25

STEREO SOUND MODE . . . . . . . . . . . . . . . .25

CAMERA ANGLE . . . . . . . . . . . . . . . . . . . . . .25

BLACK LEVEL SETTING . . . . . . . . . . . . . . .25

VIRTUAL SURROUND . . . . . . . . . . . . . . . . .25

CONNECTING TO AN AMPLIFIER/RECEIVER

EQUIPPED WITH DIGITAL INPUT JACKS

(DVD, CD, MP3 sound only) . . . . . . . . . . . . . . .11

CONNECTING TO AN AMPLIFIER/RECEIVER

WITH A DOLBY DIGITAL DECODER

(for DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

TV SECTION

C SET UP FOR USE . . . . . . . . . . . . . . . . . . . . .13

SELECTING THE LANGUAGE . . . . . . . . . . .13

CHANNEL SET UP . . . . . . . . . . . . . . . . . . . . .13

DELETING (OR ADDING) CHANNEL . . . . .14

C THE ON-SCREEN INFORMATION . . . . . . .26

C CHANGING THE DVD SETUP ITEMS . . . .27

LANGUAGE SETTING . . . . . . . . . . . . . . . . .27

DISPLAY SETTING . . . . . . . . . . . . . . . . . . . .28

AUDIO SETTINGS . . . . . . . . . . . . . . . . . . . . .28

PARENTAL CONTROL . . . . . . . . . . . . . . . . .29

INITIALIZE . . . . . . . . . . . . . . . . . . . . . . . . . . .29

C TROUBLESHOOTING GUIDE . . . . . . . . . . .30

C TV OPERATION . . . . . . . . . . . . . . . . . . . . . . .15

WATCHING A TV PROGRAM . . . . . . . . . . . .15

DEGAUSSING . . . . . . . . . . . . . . . . . . . . . . . .15

PICTURE CONTROL . . . . . . . . . . . . . . . . . . .15

SLEEP TIMER . . . . . . . . . . . . . . . . . . . . . . . . .16

CLOSED CAPTION SYSTEM . . . . . . . . . . . .16

V-CHIP SET UP . . . . . . . . . . . . . . . . . . . . . . . .17

C MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . .32

DISC HANDLING . . . . . . . . . . . . . . . . . . . . . .32

DVD SECTION

C ABOUT THE DISCS . . . . . . . . . . . . . . . . . . . .19

C SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . .33

C ESPAÑOL . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

C WARRANTY . . . . . . . . . . . . . . . . . . .Back Cover

PLAYABLE DISCS . . . . . . . . . . . . . . . . . . . . .19

DISC TYPES . . . . . . . . . . . . . . . . . . . . . . . . . .19

C PLAYING A DISC . . . . . . . . . . . . . . . . . . . . . .20

BASIC PLAYBACK . . . . . . . . . . . . . . . . . . . .20

GENERAL FEATURES . . . . . . . . . . . . . . . . . .20

DISC MENU . . . . . . . . . . . . . . . . . . . . . . . . . .20

TITLE MENU . . . . . . . . . . . . . . . . . . . . . . . . .20

RESUME . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

PAUSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

STEP BY STEP PLAYBACK . . . . . . . . . . . . .21

FAST FORWARD/REVERSE SEARCH . . . . .21

SLOW FORWARD / SLOW REVERSE . . . . .21

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

FEATURES

TV Mode

DVD Mode

¡Dolby Digital sound

This TV/DVD can output a Dolby Digital audio signal

from the digital audio output jack.

181 channel capability PLL frequency synthesiz-

er tuner

(A converter may be necessary to view scrambled cable

channels.)

•

¡Still/fast/slow/step playback

Various playback modes are available including still pic-

tures, fast forward/reverse, slow motion and frame by

frame.

Infrared remote control

•

Trilingual on screen menu display selectable in

English, Spanish, or French

¡Random playback for audio CD and MP3

This TV/DVD can shuffle the order of tracks to play them

in random order.

¡Sleep Timer

The Sleep Timer function enables the unit to turn off the

power without pressing POWER after a preselected time

period.

¡Program playback for audio CD and MP3

You can program the order of tracks to play in any desired

order.

¡Closed Caption Decoder

You may view specially labeled (cc) TV programs,

movies, news, etc. with either a dialogue caption or text

display added to the program.

¡DVD menus in a desired language

You can display DVD menus in a desired language, if

available on a DVD disc.

¡Auto Shut Off Function

¡Screen saver/Auto power-off functions

If there is no air signal input from the antenna terminal and

no operation for 15 minutes, the TV/DVD will turn itself

off automatically.

The screen saver program starts when there is no input

from the TV/DVD for five minutes in the stop mode.

When the screen saver program has been in opperation for

15 minutes, the power will automatically turn off.

¡V-CHIP

Enables parents to prevent their children from watching

inappropriate material on TV.

¡Subtitles in a desired language

You can select a desired language for the display subtitles,

if that language is available on a DVD disc.

¡Selecting a camera angle

You can select the desired camera angle, if a DVD disc

contains sequences recorded from different angles.

¡Choices for audio language and sound mode

You can select the desired audio language and sound mode,

if different languages and modes are available on a DVD

disc.

¡Parental lock

You can set the control level to limit playback of DVD

discs which may not be suitable for children.

¡Automatic detection of discs

This TV/DVD automatically detects if the loaded disc is

DVD, audio CD or MP3.

¡On-screen display

Information about the current operation can be displayed

on a TV screen, allowing you to confirm the currently

active functions (such as program playback), on the TV

screen using the remote control.

¡Search

Chapter search / Title search / Track search / Time search

¡Repeat

Chapter / Title / Track / Group / All / A-B

¡Marker

The location on a specific DVD disc designated by the

user can be accessed later.

¡Resume Play

User can resume to playback from the location at which

play was stopped.

¡Virtual Surround

¡Bit rate indication

¡DRC (Dynamic range control)

You can control the range of the difference between the

loudest abd softest sounds.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

OPERATING CONTROLS AND FUNCTIONS

[Fig. 1]

TV/DVD FRONT PANEL

OPEN/

POWER

VOLUME

CHANNEL

STOP

SKIP

PLAY

SKIP

PAUSE

VIDEO

L–AUDIO–R

–SEARCH–

HEADPHONE

1 2

7 8 9 101112 13 14

7. Remote Sensor Window

8. STOP Button [page 20]

Stops operation of the disc.

[Fig. 2]

REMOTE CONTROL

9.SKIP H Button [page 22]

Begins playback from beginning of current

chapter or track

OPEN/

POWER PICTURE SELECT

SEARCH (REV) E Button (Front Panel)

[page 21]

During playback or in the pause mode, press and

hold button down for a few seconds to change

reverse playback speed.

CH.

SLEEP

+100

10. PLAY Button [page 20]

VOL.

Begins playback of disc.

+10

V.SURR

SKIP

Press to change to DVD mode when in TV mode.

MUTE

11. SKIP G Button [page 22]

Begins playback from beginning of next chapter.

PLAY

STOP

REV

FWD

SEARCH (FWD) D Button (Front Panel)

[page 21]

During playback or in the pause mode, press and

hold button down for a few seconds to change for-

ward playback speed.

DISC

PAUSE SLOW

DISPLAY

ENTER

SETUP

TITLE

RETURN

12. PAUSE Button [page 21]

Pauses the current disc movement.

CLEAR SEARCH MODE REPEAT

A-B

13. OPEN/CLOSE Button [page 20]

Press to open disc tray to insert a disc or to open to

remove a disc.

14. HEADPHONE Jack

To connect headphone (not supplied) for personal

listening.

AUDIO SUBTITLE ANGLE

MODE

15. MODE Button [pages 23-25]

Activates program playback or random playback

mode when playing CDs or MP3.

1. Disc loading tray

2. VIDEO input Jack [page 11]

Connect to the video output jack of a video

camera, VCR or Video game system.

3. AUDIO L/R input Jacks [page 11]

Connect to the audio output jacks of a video

camera, VCR or Video game system.

4. POWER Button [page 13]

Press to turn the power on and off.

5. VOLUME K/L (VOL. m/n) Buttons

Press to control the volume level.

16. Number Buttons

TV Mode: [page 15]

Press two digits to directly access the desired channel.

Remember to press 0 before a single digit channel.

+100 Button

Press to select cable channels which are higher than 99.

DVD Mode: [page 22]

Press to enter the desired number.

+10 Button

Press to enter the desired numbers which are greater

than 9.

6. CHANNEL K/L (CH. K/L) Buttons [page 13]

Press to select memorized channel.

Press to change to TV mode when in DVD mode.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

[Fig. 3]

TV/DVD REAR VIEW

ANT.

COAXIAL

38 39

32. Arrow Buttons

17. SLEEP Button [page 16]

TV Mode: [page 13]

Press SLEEP to display the sleep timer and begin

operation. The shut off time can be determined by

the number of times you press this button. (0, 30,

60, 90, or 120 minutes)

Press to select a setting mode from the menu on the

TV screen.

Press to select or adjust from a particular menu.

DVD Mode: [page 20]

18. REV h Button [page 21]

Use when making settings while watching the

display on a TV screen.

Press to view the DVD picture in fast reverse

motion. Press PAUSE, then press this button to begin

slow motion playback. Press this button repeatedly

to change the reverse speed of slow motion.

33. DISC MENU Button [page 20]

Displays the menus available on a DVD disc.

34. SELECT Button [page 20]

Press to change to TV mode, FRONT A/V input

mode or DVD mode.

FWD g Button [page 21]

Press to fast forward the Disc. Press PAUSE, then

press this button to begin slow motion playback.

Press this button repeatedly to change the forward

speed of slow motion.

NOTE: When you select the DVD mode by this

button, press PLAY or OPEN/CLOSE first.

Otherwise, the DVD features do not function.

19. V.SURR (VIRTUAL SURROUND) Button

[page 25]

Press to set virtual surround on/off.

35. MUTE Button

20. SETUP Button [pages 13,27-29]

Press to enter or exit the TV menu or DVD setup

mode.

Press MUTE to turn off the sound

portion of the TV program. (Volume level display

turns LIGHT RED from LIGHT BLUE.) Press

MUTE again or press VOL. m or n to restore

sound.

21. TITLE Button [page 20]

Displays the title menu on DVD disc.

36. PICTURE Button [page 15]

22. CLEAR Button [pages 22-24]

Press to enter picture adjustment mode.

Resets a setting.

37. Power cord

23. DISPLAY Button

Connect to a standard AC outlet (120V/60Hz).

NOTE: Remove the power cord from the hook on

the back of the TV to avoid breaking a wire

before you connect to a standard AC outlet.

38. COAXIAL digital audio out Jack (DVD, CD, MP3

Audio Only) [pages 11, 12]

TV Mode:

Press to display the channel number on the screen.

If you press it a secound time, the channel number

will disappear.

DVD Mode: [page 26]

Displays the current DVD status on the TV screen.

Connect to the digital input of an external

amplifier or receiver.

24. SEARCH MODE Button [page 22]

Press to locate a desired point.

39. ANT. in Jack

25. AUDIO Button [page 25]

Connect to an antenna, cable system, or satellite sys-

tem.

Press to select a desired audio language or sound

mode available on a DVD disc.

26. SUBTITLE Button [page 25]

Press to select a desired subtitle language.

27. REPEAT Button [page 23]

Repeats playback of the current disc, title, chapter

or track.

INSTALLING THE BATTERIES

1)Open the battery compartment cover by pressing the

cover on the remote unit in the direction of the arrow.

2)Insert 2 “AA” penlight batteries into the battery

compartment in the direction indicated by the

polarity (+/-) markings.

28. ANGLE Button [page 25]

Press to change the camera angle to see the sequence

being played back from a different angle available on

a DVD disc

29. REPEAT A-B Button [page 23]

Repeats playback of a selected section.

3)Replace the cover.

30. RETURN Button [page 25]

Returns to the previous operation in the DVD setup

mode.

NOTES

31. ENTER Button [pages 13, 20]

¡Do not mix alkaline and manganese batteries.

¡Do not mix old and new batteries.

Press to accept a setting.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

PREPARATION FOR USE

ANTENNA/CABLE CONNECTIONS

From Cable System or

Satellite Box or

Cable Box

(Not supplied)

VHF/UHF Antenna

(Not supplied)

OUT

Satellite Dish

VHF Antenna

(Not supplied)

UHF Antenna

(Not supplied)

From

Cable System

ANT.

COAXIAL

VHF/UHF

Combiner

(Not supplied)

ANT.

75-ohm Coaxial

Cable (Not supplied)

Flat twin-lead cable

[Fig. 4]

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides

guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding

system of the building as close to the point of cable entry as practical.

Bent pin

NOTE:

Before plugging the antenna into the ANT. IN jack of the TV/DVD, check that

the pin is not bent. If it is bent, straighten the pin as illustrated, then plug the pin

into the ANT. IN jack of the TV/DVD.

Cable

Plug

(Needs to be straightened)(Straight pin)

VHF/UHF COMBINED ANTENNA

A VHF UHF 75 ohm combination antenna can be

connected to ANT terminal.

CABLE WITH CONVERTER/DESCRAM-

BLER BOX OR SATELLITE BOX

If your cable service supplies you with a converter

box or if you use a satellite system, you can use the

basic connection shown here.

VHF/UHF SEPARATE ANTENNAS

Channel selection must be made with the converter

box or satellite box. This means that channels cannot

be changed using the TV/ DVD Remote Control.

In some areas it will be necessary to use an outdoor

antenna.

CABLE WITHOUT CONVERTER/

DESCRAMBLER BOX

Use this connection if your cable system connects

directly to your TV/DVD without a converter box.

Use the TV/ DVD Remote Control to select channels.

TO VIEW A SCRAMBLED/UNSCRAMBLED

CHANNEL

1.Set the TV/DVD channel selector to the output

channel of the Cable Converter Box or Satellite

Box. (Ex. CH3)

2.Select the channel to view at your Cable Converter

Box or Satellite Box.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

CONNECTING TO FRONT A/V INPUT JACKS

When you watch a program recorded on an another

[Front of the TV/DVD]

source (VCR, video camera or Video game system),

use the audio/video input jacks on the front of the

TV/DVD.

To the

[Another source]

audio out-

put jacks

Connect the audio/video output

jacks of the source to the AUDIO

L/R and VIDEO jacks of this

TV/DVD. Then press SELECT until

"AUX" appears on the screen.

NOTE:

AUX

VIDEO

L–AUDIO–R

Audio/Video

cables

(not supplied)

When you connect a monaural VCR (another

etc.

•

source) to this TV/DVD, connect the Audio output

jack of the monaural VCR (another source) to the

AUDIO L jack of this TV/DVD. The audio will

distributed in both L and R channel equally.

To the video

output jack

[Fig. 5]

CONNECTING TO AN AMPLIFIER/RECEIVER EQUIPPED WITH

DIGITAL INPUT JACKS (DVD, CD, MP3 sound only)

Use an audio coaxial digital cable available at retail stores for the audio connections.

Amplifier/Receiver equipped with

digital input jacks.

ANT.

COAXIAL

To COAXIAL DIGITAL

AUDIO INPUT jack

To DIGITAL AUDIO OUT

(PCM/BITSTREAM)

COAXIAL jack

(only DVD, CD, MP3 AUDIO OUT)

[Fig. 6]

NOTES:

The audio source on a disc in a 5.1 channel Dolby Digital surround format cannot be recorded as digital

sound by an MD or DAT deck.

•

Be sure to turn off the power to all components in the system before making connections.

Refer to the Owner's Manuals for the components to be connected to the TV/DVD.

Set DOLBY DIGITAL to OFF for audio output in the setup mode. Playing a TV/DVD using incorrect set-

tings may generate noise distortion, and may also damage the speakers. (See page 28 to set DOLBY

DIGITAL to OFF.)

•

This will only allow 2-channel DVD sound to be listened to on the amplifier.

•

–

_{Download from Www.Somanuals.co}1_m1_{. All Manuals Search And Download.}

0C28

CONNECTING TO AN AMPLIFIER/ RECEIVER WITH A

DOLBY DIGITAL DECODER (for DVD)

To use this TV/DVD to play a DVD disc in a 5.1 channel Dolby Digital surround format, the TV/DVD can

outputs a DOLBY DIGITAL Data stream from its COAXIAL digital audio out jack. By hooking the player up

to a receiver with Dolby Digital decoder, you can enjoy high-quality surround sound as enjoyed in movie the-

aters.

Use audio coaxial digital cables available at retail stores for the audio connections.

Center

speaker

ANT.

COAXIAL

Front speaker

(left)

Front speaker

(right)

Ampliifier/RReceivveer with

Dolby Digital decoder

To DIGITAL AUDIO OUT

(PCM/BITSTREAM)

COAXIAL jack

To COAXIAL DIGITAL

AUDIO INPUT jack

Subwoofer

Surround

speaker

(left)

Surround

speaker

(right)

[Fig. 7]

NOTES:

Be sure to turn off the power to all components in the system before connecting another component.

Refer to the Owner's Manuals for the components to be connected to the TV/DVD.

If connected to a receiver with Dolby Digital decoder, set DOLBY DIGITAL to ON for audio output in the

setup mode. (See page 28 to set DOLBY DIGITAL to ON.)

•

Unless connected to a receiver with Dolby Digital decoder, set DOLBY DIGITAL to OFF for audio output

in the setup mode. Playing a TV/DVD using incorrect settings may generate noise distortion, and may also

damage the speakers.

•

Only DVD audio is available using the digital audio out jack.

•

Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are

trademarks of Dolby Laboratories.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

TV SECTION

SET UP FOR USE

SELECTING THE LANGUAGE

CHANNEL SET UP

You can program the TVs tuner to program all the

1 Plug in the TV/DVD power cord

Plug the TV/DVD power cord into a

standard AC outlet.

channels you receive in your area.

NOTE: Channel memory programming is NOT

needed when connected to a cable box or satellite

box. Just select the TV/DVD channel selector to the

output channel of the cable box or satellite box (Ex

CH3). Then select the channel to be viewed on the

Cable Box or Satellite Box.

NOTE:

If any digits appear in the corner of

the screen, press POWER without

unplugging the power cord.

•

Make sure ...

Press POWER to turn on the TV/DVD.

•

Press POWER to turn on the TV/DVD.

•

NOTE: This function effects only the language on

the screen menu and not the audio source.

1 Select “CHANNEL SET UP”

Press SETUP on the remote control.

Press Arrow (K/L) to point to

“CHANNEL SET UP”.

- TV SETUP -

2 Select “LANGUAGE”

CHANNEL SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

CHANNEL SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

Press SETUP on the remote control.

Press Arrow (K/L) to point to

“LANGUAGE”.

Then, press ENTER.

2 Begin auto ch programming

Press Arrow (K/L) to point to

“AUTO CH PROGRAMMING”.

Then, press ENTER.

3 Select “ENGLISH”, “ESPAÑOL” or “FRANÇAIS”

Select “ENGLISH”, “ESPAÑOL”= Spanish or

“FRANÇAIS”= French using ENTER.

– CHANNEL SET UP –

ADD / DELETE CH (CATV)

AUTO CH PROGRAMMING

The tuner scans and memorizes all

the active channels in your area.

4 Exit the Language mode

Press SETUP to return to TV mode.

NOTE: If for some reason the menu is in Spanish or

French, press SETUP, press Arrow (K/L) to point to

“IDIOMA [ESPAÑOL]” or “LANGAGE

[FRANÇAIS]”, then press ENTER, then press

SETUP on the remote control.

3 After scanning

The tuner stops on the lowest memorized channel.

•

When AUTO CH PROGRAMMING is activated

where there is no TV signal input, “NO TV SIG-

NALS” will appear on the display after the com-

pletion of the channel scanning.

CHANNEL PRESETTING:

The TV may memorize TV channels as CATV

•

channels if reception conditions are poor. If this

happens, check the antenna connections and try the

AUTO PRESET CH action again, or wait until

reception conditions are better and then try it again.

–

_{Download from Www.Somanuals.co}1_m3_{. All Manuals Search And Download.}

0C28

DELETING (OR ADDING)

CHANNEL

The channels you no longer receive or seldom watch

can be deleted from the memory. (Of course, you can

add the deleted channel into the memory again.)

1 Select “CHANNEL SET UP”

Press SETUP on the remote control.

- TV SETUP -

Press Arrow (K/L) to point to

“CHANNEL SET UP”.

CHANNEL SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

Then, press ENTER.

– CHANNEL SET UP –

2 Select “ADD/DELETE CH”

Press Arrow (K/L) to point to

“ADD/DELETE CH”.

ADD / DELETE CH (CATV)

AUTO CH PROGRAMMING

Press ENTER.

3 Enter the desired channel number

Press Arrow (K/L) until your

desired channel number appears.

(You can also use the number but-

tons or CHANNEL(CH.) K/L to

enter it) (Example: CH8)

ADD / DELETE

You must proceed single-digit

•

channel numbers with a zero (Example: 02 ... 09).

When selecting cable channels which are higher

than 99, press +100 first, then, press the last two

digits. (Example: to select channel 125, first press

+100, then press 2 and 5).

•

4 Delete (or add) it from (into) memory

Press ENTER. The channel number changes to light

red. The channel is deleted from memory.

To delete another channel, repeat steps [3] and [4].

If you press ENTER again, the channel is memo-

rized again.

•

Added channel: Light blue.

Deleted channel: Light red.

5 Exit the channel setup mode

Press SETUP to return to TV mode.

NOTE: To confirm that channel(s) has been deleted

or added, press CHANNEL(CH.) K/L.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

TV OPERATION

WATCHING A TV PROGRAM

PICTURE CONTROL

1 Turn on the TV/DVD

Press POWER to turn on the TV/DVD.

The TV/DVD’s picture controls – BRIGHT, CON-

TRAST, COLOR, TINT and SHARPNESS – are

preset to factory specifications. Although they are

usually the best, you may need to make some further

adjustments for your individual preference.

2 Select the channel number

Press CHANNEL(CH.) K/L to select your desired

channel number, or press the number buttons.

Notes for using the number buttons on the remote

control:

Make sure ...

TV/DVD power must be turned on.

•

You must proceed single-digit channel numbers

with a zero (Example: 02 ... 09).

When selecting cable channels which are higher

than 99, press +100 first, then press the last two

digits. (Example: to select channel 125, first press

+100, then press 2 and 5).

•

1 Select “PICTURE CONTROL”

Press PICTURE on the remote control.

•

2 Select item you want to adjust

Press Arrow (K/L) until desired control is displayed.

Remember:

¡If the TV/DVD is connected to a cable box or

satellite box, the TV/DVD must be on CH3 or

CH4, then the channel to be viewed must be select-

ed on the cable box or satellite box.

BRIGHT

CONTRAST

COLOR

BRIGHT

TINT

–

P +

SHARPNESS

3 Adjust sound

Press VOLUME(VOL.)

adjust the volume.

3 Adjust the picture control

Press Arrow (s / B) to adjust to your desired level

VOLUME 20

within 5 seconds.

NOTE:

If you press CHANNEL(CH.) K/L in the DVD

mode, you can change the TV channels.

•

At step [3], the picture adjustment display will dis-

appear from the TV screen after about 5 seconds

unless you press any buttons, even though you may

not be finished. In this case, repeat from step [1].

•

When you turn off the TV/DVD in the DVD mode,

when you turn it on again, it will return to the TV

mode.

Arrow Button

{

Arrow Button

to decrease

brightness

to increase

brightness

BRIGHT

DEGAUSSING

This television has a degaussing circuit that will clear

up color errors on the TV screen that are caused by

any excess magnetism which happens to get too

close to the TV. This circuit is designed to operate

once when the set is first plugged in. If minor color

errors are seen in some locations on the screen,

please unplug the TV for approximately 15 minutes.

When the TV is plugged back in, the degaussing cir-

cuit will operate once to clear them up. Repeat this

procedure any time the TV screen is accidentally

magnetized, or when the TV is moved or relocated.

to increase

contrast

to decrease

contrast

CONTRAST

to pale

to purple

to soft

to brilliant

to green

COLOR

TINT

to clear

SHAPNESS

If there is a power failure of any kind, the unit will

retain its memory of the setting you have selected.

•

–

_{Download from Www.Somanuals.co}1_m5_{. All Manuals Search And Download.}

0C28

NOTE:

SLEEP TIMER

If the TV/DVD displays a black

box on the TV screen, this means

that the TV/DVD is set to the

TEXT mode. To clear screen, select

[CAPTION1], [CAPTION2] or

[OFF].

he Sleep Timer function enables you to shut off the power

without pressing POWER after a selected time period.

1 Set “SLEEP TIMER”

Make sure ...

Press SLEEP on the remote control.

You may change the sleep time

with pressing SLEEP repeatedly.

TV/DVD power must be turned on.

•

The timer can be set up to 120 min-

utes. Each time SLEEP is pressed,

the sleep time increases 30 minutes.

- TV SETUP -

1 Select “CAPTION”

Press SETUP on the remote control.

Press K or L to point to “CAP-

SLEEP 120 MINUTE

CHANNEL SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

TION”.

To cancel the sleep timer:

Press SLEEP repeatedly until “SLEEP 0 MINUTE”

is displayed.

2 Select your desired caption menu

Press ENTER until your desired

NOTES:

- TV SETUP -

When you disconnect the unit from the AC outlet,

or if you have a power failure, the sleep time will

be cancelled.

•

CHANNEL SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

caption menu appears.

([CAPTION1], [CAPTION2],

[TEXT1] or [TEXT2])

To view the time left for sleep timer press SLEEP

once when SLEEP display disappears. After 10

seconds, display will disappear again.

•

3 Exit the caption setting mode

Press SETUP to return to TV mode.

CLOSED CAPTION SYSTEM

You can view specially labeled (cc) TV programs,

movies, news, etc. with either a dialogue caption or

text display.

TO CANCEL THE CLOSED CAPTION

SYSTEM

Repeat steps [1] and [2], select [OFF] using ENTER.

Press SETUP on the remote control to return to TV

mode.

CAPTION mode: By choosing the caption mode, you

can watch dramas, movies and news while captioning

the dialogues and the contents of news appears.

TEXT mode: By choosing the text mode, you can

watch half screen text information if you want.

1-2: You may view these captions or text information

by selecting either “1” or “2”. Caption “2” is used,

usually for a second language if available.

WHEN THE CLOSED CAPTION MODE

IS ON

The On-Screen Display will disappear after 5 sec-

onds.

This is also true when MUTE is pressed.

If there is a power failure of any kind, the unit will

retain its memory of this feature.

NOTE:

•

Not all programs are broadcast with closed captions.

Your television is designed to provide error free

closed captions from high quality antenna, cable and

VCR signals. Conversely, poor quality signals are

likely to result in caption errors or no captions at all.

Common signal conditions which may cause captions

errors are listed below:

Automobile ignition noise

Electric motor noise

Weak or snowy reception on TV screen

Multiplex signal reception displaying picture

•

ghosts.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

V-CHIP SET UP

When you select a rating category and turn it

[BLOCK], the higher rating will turn [BLOCK]

automatically. Also, the lower rating will turn

[VIEW] automatically.

When you turn “TV-Y” to [VIEW], all ratings will

turn to [VIEW] automatically.

•

V-CHIP enables parents to prevent their children

from watching inappropriate material on TV.

V-CHIP reads the ratings for programming (except

for news and sports programs, unedited movies on

premium cable channels, and Emergency Broadcast

System signals), then denies access to programming

if the program’s rating meets the limitations you

select. In this case, “PROTECTED PROGRAM by

...” message appears on the TV screen.

Selection

TV-Y

Rating Category Explanations

Appropriate for all children

TV-Y7

TV-G

Appropriate for children seven and older

General Audience

TV-PG

TV-14

Parental Guidance suggested.

Unsuitable for children under 14

To block ratings, follow the steps below.

TV-MA Mature audience only

Programming may be rated by the Motion Picture

•

Association of America (MPAA) or according to

the Television Parental Guidelines. In order to

block any inappropriate programming, set your

limits in both places (MPAA RATING and TV

RATING).

When you select TV-Y7, TV-PG, TV-14, or TV-MA

and you press ENTER, the sub-ratings will appear

on the TV screen.

If you select the rating category (example: TV-PG)

and turn it [BLOCK] or [VIEW], the sub-ratings

(example: V for Violence) will turn [BLOCK] or

[VIEW] automatically.

TV RATING SET UP

You can set the sub-ratings to [BLOCK] or [VIEW]

individually when the rating category is set to

[BLOCK].

Make sure ...

TV/DVD power must be turned on.

•

To set the sub-ratings individually, follow the steps

below.

- TV SETUP -

1 Select “V-CHIP SET UP”

Press SETUP on the remote control.

Press Arrow (K/L) to point to “V-

CHIP SET UP”.

Then, press ENTER.

CHANNEL SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

When you select [TV-Y7]:

•

TV–Y7

[BLOCK]

Press Arrow (K/L) to select

“FV” (Fantasy Violence).

Then, press ENTER to select

[BLOCK] or [VIEW].

2 Input Access code

Press the number buttons to enter 4-

digit access code. The default code

is 0000.

ACCESS CODE

When you select [TV-PG], [TV-14] or [TV-MA]:

Press Arrow (K/L) to select

•

“D”(Suggestive Dialog),

TV–PG

[BLOCK]

“L”(Coarse Language),

“S”(Sexual Situation), or

“V”(Violence). Then, press

ENTER to select [BLOCK] or [VIEW].

NOTE: When you select [TV-MA], “D” does not

appear on the TV screen.

3 Select “TV RATING”

Press Arrow (K/L) to point to “TV

RATING”.

– V-CHIP SET UP –

TV RATING

MPAA RATING

CHANGE CODE

The sub-ratings which set to

TV–Y

TV–Y7

TV–G

TV–PG (DLSV)

TV–14 (DLSV)

TV–MA ( LSV)

[VIEW]

(

)

[VIEW]

Then, press ENTER.

[VIEW]

[BLOCK] appears next to the rat-

ing category in the TV RATING

menu.

[BLOCK]

4 Select your desired item

Press Arrow (K/L) to point to your

desired item.

Then, press ENTER to select

[BLOCK] or [VIEW].

TV–Y

TV–Y7

TV–G

TV–PG (

TV–14

TV–MA(

[VIEW]

(

)

[VIEW]

5 Exit the V-Chip setting mode

Press SETUP on the remote control to return to orig-

inal mode.

)

(

–

_{Download from Www.Somanuals.co}1_m7_{. All Manuals Search And Download.}

0C28

MPAA RATING SET UP

CHANGE ACCESS CODE

Make sure ...

To change access code, follow the steps.

TV/DVD power must be turned on.

•

1 Select “V-CHIP SET UP”

Press SETUP on the remote con-

trol.

Press Arrow (K/L) to point to “V-

CHIP SET UP”.

- TV SETUP -

1 Select “V-CHIP SET UP”

Press SETUP on the remote control.

Press Arrow (K/L) to point to “V-

CHIP SET UP”.

- TV SETUP -

CHANNEL SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

CHANNEL SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

Then, press ENTER.

ACCESS CODE

2 Enter 4-digit access code

Press the number buttons. The

default code is 0000.

2 Enter 4-digit access code

Press the number buttons. The

default code is 0000.

ACCESS CODE

– V-CHIP SET UP –

3 Select “CHANGE CODE”

Press Arrow (K/L) to point to

“CHANGE CODE".

– V-CHIP SET UP –

3 Select “MPAA RATING”

Press Arrow (K/L) to point to

“MPAA RATING”.

TV RATING

MPAA RATING

CHANGE CODE

TV RATING

MPAA RATING

CHANGE CODE

Then, press ENTER.

4 Enter 4-digit access code

Press the number buttons to enter

your desired access code in the

NEW CODE space. Then, enter the

same code in the CONFIRM

CODE space. V-CHIP SET UP

screen appear on the screen.

NEW CODE

Selection

PG-13

Rating Category Explanations

General Audience

CONFIRM CODE

Parental Guidance suggested.

Unsuitable for children under 13

Restricted; under 17 requires accompa-

nying parent or adult guardian

No one under 17 admitted

If you enter wrong code, repeat step 4, making

•

NC-17

sure you enter the same new code exactly in the

confirm code space.

Mature audience only

5 Exit the V-Chip setting mode

Press SETUP on the remote control to return to orig-

inal mode.

4 Select your desired item

Press Arrow (K/L) to point to your

desired item.

Then, press ENTER to select

[BLOCK] or [VIEW].

[VIEW]

PG–13

NC–17

[VIEW]

[BLOCK]

NOTE: IF YOU FORGET YOUR ACCESS

CODE NUMBER

If you unplug the power cord or if a power failure

occurs, your changed access code will be lost and

the code will return to default (0000). Change your

access code again as necessary.

When you select the rating cate-

•

gory and turn it [BLOCK], the higher rating will

turn [BLOCK] automatically. Also, the lower rat-

ing will turn [VIEW] automatically.

When you turn “G” to [VIEW], all ratings will turn

to [VIEW] automatically.

•

5 Exit the V-Chip setting mode

Press SETUP on the remote control to return to origi-

nal mode.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

DVD SECTION

ABOUT THE DISCS

PLAYABLE DISCS

DISC TYPES

The following discs can be played back on this TV/DVD.

[

]

DVD

Data on a DVD is divided into sections called "titles", and

then into subsections called "chapters", each of which is

given a title or chapter number. Playback conditions are

preset on some DVD video discs, and these playback con-

ditions take priority over user operations on this

TV/DVD. If a function you selected does not run as

desired, refer to the manual accompanying the disc.

DVD video

DVD+R/RW*

CD-R/RW*

DVD-R/RW*

Audio CD

MP3*

* Depending on the types or the writing method of the

medium some discs can not be played.

• Some DVD-R/RW, DVD+R/RW, or CD-R/RW discs

made on personal computers, or on DVD recorders may

not be played back properly due to the factors such as

scratches, dirt or special properties of the disc.

• Discs made on personal computers may not be played

back properly due to the different environment or the

settings of the application you use. We recommend

always to use the standardized formatted discs.

Example

Title 1

Title 2

Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1 Chapter 2

This TV/DVD conforms to the NTSC color system. You

cannot play discs recorded in other color systems such as

PAL or SECAM.

[

]

AUDIO CD

Data on an audio CD is divided into sections called

“tracks”, each of which is given a track number.

¡Some discs include region codes as shown below.

Example

Track 1

Track 2

Track 3

Track 4

Track 5

Track 6

¡The number inside the symbol refers to a region of the

world, and a disc encoded in a specific region format

can only be played back on TV/DVD with the same

region code.

The following discs cannot be played back on this

TV/DVD.

[

]

MP3

Data on an MP3 is divided into sections called "groups",

and then into subsections called "tracks", each of which is

given a group or track number.

DVD with region codes other than 1 or ALL

DVD-ROM

DVD-RAM (Never play back, otherwise malfunc-

tion may result.)

Example

Group 1

Group 2

CD-ROM

Track 1

Track 2

Track 3

Track 4

Track 5

Track 6

VSD

CDV (Only plays back the audio part.)

CD-G (Only plays back the sound.)

CD-I (Never play back, otherwise malfunction

may result.)

SACD

Photo CD (Never play back, otherwise malfunc-

tion may result.)

Video CD (Never play back, otherwise malfunc-

tion may result.)

Any other discs without compatibility indications.

–

_{Download from Www.Somanuals.co}1_m9_{. All Manuals Search And Download.}

0C28

PLAYING A DISC

BASIC PLAYBACK

GENERAL FEATURES

DVD-V

MP3

DVD-V

DVD may contain menus to navigate the disc and

access special features. Press appropriate numerical key

or use Arrow (L/K/s/B) to highlight your selection in

the DVD main menu and press ENTER to confirm.

NOTES

¡Select DVD mode by pressing SELECT on the

remote control. Then, press PLAY or OPEN/CLOSE

before you operate the DVD functions.

Getting started

Press POWER.

¡The power will turn on.

Press OPEN/CLOSE to open disc loading

tray.

Place the chosen disc in the tray, with the

label facing up.

¡Unless stated, all operations described are based on

remote control use. Some operations can be carried

out using the menu bar on the TV screen.

DISC MENU

DVD-V

Press DISC MENU on the remote control.

Press PLAY.

¡The DVD main menu will appear.

¡The tray will close automatically and playback will

then start from the first chapter or track of the disc.

If the playback does not start automatically, press

PLAY.

If the feature is not available,

may appear on the TV screen.

symbol

¡When you playback a DVD which features a title

menu, it may appear on the screen. In this case, refer

to “TITLE MENU”.

If disc menu is available on the disc, audio

language, subtitle options, chapters for the

title and other options will appear for selec-

tion.

Press STOP to stop playback.

Press Arrow (L/K/s/B) to select an item,

and ENTER to confirm selection.

NOTES

¡When the DVD mode has been switched to the TV

mode, the DVD mode shuts down first and then a

TV picture and sound appears in about 4 seconds.

Similarly, when POWER is pressed to turn off in the

DVD mode, the mode shuts down first and then the

TV/DVD’s power is turned off.

TITLE MENU

DVD-V

Press TITLE on the remote control.

¡The title menu will appear.

¡A “prohibited icon” may appear at

the top-right on the TV screen dur-

ing operation, warning that a pro-

hibited operation has been encoun-

tered by the DVD or the disc.

¡With DVDs that use titles for playback program sig-

nals, playback may start from the second title, or it

may skip these titles.

¡During the playback of a two layered disc, pictures

may stop for a moment. This happens when the 1st

layer switches to the 2nd layer. This is not a mal-

function.

If the feature is not available,

may appear on the TV screen.

symbol

Press Arrow (L/K/s/B) to select an item,

and ENTER to confirm selection.

RECALLING A MENU SCREEN

DURING PLAYBACK

For DVD-Vs

¡Press DISC MENU to display the DVD menu.

¡Press TITLE to display the title menu.

NOTE

¡Contents of menus and corresponding menu opera-

tions may vary between discs. Refer to the manual

accompanying the disc for details.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

FAST FORWARD/REVERSE

RESUME

DVD-V

MP3

DVD-V

MP3

During playback, press STOP.

¡Resume message will appear on the TV screen.

During playback, press FWD g or REV h.

¡“g 1” or “h 1” appears on the screen.

Press PLAY, playback will resume from the

point at which playback was stopped.

To select another speed, repeat step1 until

your required speed appears on the screen.

¡To cancel resume, press STOP twice.

¡If the TV/DVD is turned off, resume function will be

cancelled.

¡For MP3, playback will resume from the beginning

of the track at which playback was stopped.

¡For DVDs, fast forward/reverse search speed is dif-

ferent depending on the disc. Approximate speed is

1(×2), 2(×8), 3(×50) and 4(×100).

¡For audio CDs, approximate speed is ×16.

¡For MP3, approximate speed is ×8

¡When you use buttons on the main unit, press and hold

SKIPG/ SEARCHg or SKIPH/ SEARCHh

for a few seconds.

PAUSE

DVD-V

MP3

To return to normal playback, press PLAY.

During playback, press PAUSE.

¡Playback will pause and sound will be muted.

SLOW FORWARD /

SLOW REVERSE

To continue playback, press PLAY.

DVD-V

STEP BY STEP PLAYBACK

During playback, press PAUSE.

DVD-V

Press FWD g or REV h .

¡“

1” or “

1” appears on the screen.

During playback, press PAUSE.

To select another speed, repeat step2 until

your required speed appears on the screen.

¡Playback will pause and sound will be muted.

¡Slow forward or reverse speed varies with the disc.

Approximate speed is 1(1/16), 2(1/8) and 3(1/2).

¡When you use buttons on the main unit, press and hold

SKIPG/ SEARCHg or SKIPH/ SEARCHh

for a few seconds.

The disc goes forward by one frame each

time PAUSE is pressed.

To exit step by step playback, press PLAY.

To return to normal playback, press PLAY .

–

_{Download from Www.Somanuals.co}2_m1_{. All Manuals Search And Download.}

0C28

SEARCH FUNCTION

TRACK SEARCH

TIME SEARCH

MP3

DVD-V

There are three ways to begin playback on an Audio

CD and MP3 at a specific track.

During playback, press SEARCH MODE

three times (CD: twice) to display the Time

Search on the TV screen.

Using the number buttons on the remote control

Within 30 seconds, enter a desired disc

time using the number buttons.

Press the number buttons to enter the

desired track number.

¡Playback will start at the specified time.

¡Press CLEAR to erase the incorrect input.

¡When there is no need to enter a number, “0”

appears automatically. For example, “ 0 : 0

appears in the Time Search display if the total time

of the disc is less than 10 minutes.

¡Playback will start at the selected track.

¡For single digit tracks (1-9), press a single number

(eg. track 3, press 3).

”

- -

¡To play track 26, press +10, 2, 6.

Using SEARCH MODE

MARKER SETUP SCREEN

Press SEARCH MODE.

¡The Track search display appears.

DVD-V

Within 30 seconds, select a desired track

number using the number buttons.

Use markers to memorise your favorite places on a

disc.

¡For single digits press 0 first.

¡Playback will start at the selected track.

Press SEARCH MODE four times (CD: three

times) during playback.

Using SKIP

¡The display screen and Markers will appear on the

TV screen.

During playback, press SKIP G to move the next

track. Press it repeatedly to skip subsequent tracks.

Press SKIP H to go back to beginning of the current

track. Press it repeatedly to go to the previous tracks.

¡If SKIP is pressed while the playback is paused, the

playback will be paused again after skipping to the

next track.

Press Arrow (s / B) to select 1, 2, 3, 4, 5, 6,

7, 8, 9, or 10 and ensure that “

appears in the display.

”

- - - - - - - -

When you reach the desired point, press

ENTER.

NOTE

¡SKIP

G is not available when playback is

¡The title or track and elapsed playing time will

stopped.

appear in the TV screen.

To return to the Marker later, press SEARCH

MODE four times (CD: three times) during

playback and Arrow (s / B) to choose the

desired marker, then press ENTER.

TITLE / CHAPTER SEARCH

DVD-V

NOTES

¡Opening the disc tray or turning off the power or

selecting AC at step 2 and pressing ENTER will

erase all Markers.

Press SEARCH MODE once for the Chapter

search, twice for the Title search during

playback.

¡To clear a marker, using Arrow (s /B), position the

_/2

cursor on to the marker number to be cleared and

press CLEAR.

¡You can mark up to 10 points.

Enter the desired chapter/title number using

the number buttons.

Press SEARCH MODE or RETURN to exit.

¡Playback will start at the selected chapter or track.

¡Press CLEAR to erase the incorrect input.

¡For single digits press 0 first.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

SPECIAL PLAYBACK FUNCTION

REPEAT

PROGRAM

REPEAT is available only during playback.

You may determine the order in which tracks will play.

REPEAT TITLE / CHAPTER

DVD-V

In stop mode, press MODE.

¡The PROGRAM screen will appear.

To activate the repeat function, press REPEAT

during playback.

¡The repeat mode changes as described below every

time you press the button.

Press Arrow (▲/▲) to select a track, then

press ENTER.

¡Press CLEAR to erase the

most recently entered pro-

gram.

TOTAL

CHAPTER

(current chapter repeat) (current title repeat)

TITLE

OFF

(repeat off)

NOTES

¡Repeat Title/Chapter is not available with some

scenes.

¡The REPEAT setting will be cleared when moving

to other title or chapter.

Repeat step 2 until you have selected all the

tracks you want to play in the program.

Press PLAY to play the programmed tracks.

NOTES

REPEAT TRACK

¡While the program is being played back, the STOP

works as follows.

¡Press STOP once and then PLAY again, playback

will restart from the point where STOP was pressed.

(Program continued)

¡Press STOP twice and then PLAY again, playback will

restart from the track in the usual way. (Program cleared)

¡Up to 99 programs can be entered.

¡To erase all programs at once, select ALL CLEAR at

the bottom of the list at Step2.

¡If you like to repeat the current track in the program,

To activate the repeat function, press REPEAT

during playback.

¡The repeat mode changes as described below every

time you press the button.

TRACK

ALL

OFF

(repeat off)

(current track repeat)

(entire disc repeat)

press REPEAT repeatedly until

TRACK appears

NOTES

during playback. If you like to repeat the entire pro-

¡Repeat setting will be cleared when moving to other

gram press REPEAT repeatedly until

appears during playback.

ALL

track.

¡Repeat playback does not function during repeat A-

RANDOM PLAYBACK

B playback.

REPEAT A-B

DVD-V CD

This shuffles the playing order of tracks instead of

playback in sequence as recorded on the disc.

Press REPEAT A-B at your chosen starting

point.

A- appears briefly on the TV screen.

In stop mode, press MODE twice.

¡RANDOM screen appears.

RANDOM

Press REPEAT A-B again at your chosen

end point.

CD-DA

TOTAL 0:45:55

RANDOM PROGRAM

- - no indication - -

A-B appears briefly on the TV screen, and the

repeat sequence begins.

PLAY

To exit the sequence, press REPEAT A-B.

NOTES

Press PLAY to start random playback.

NOTE

¡The repeat A-B section can only be set within the cur-

rent title (for DVDs), or current track (for audio CDs).

¡Repeat A-B is not available with some scenes in DVD.

¡To cancel the A point which was set, press CLEAR.

¡Repeat A-B playback does not function during title,

chapter, track or all repeat playback.

¡If you like to repeat the current track in the random

selection, press REPEAT repeatedly until

TRACK appears during playback. If you like to

repeat the entire random selection press REPEAT

repeatedly until

ALL appears during playback.

–

_{Download from Www.Somanuals.co}2_m3_{. All Manuals Search And Download.}

0C28

PLAYING A MP3 DISC

MP3 PLAYBACK

PROGRAM

MP3

When a CD with MP3 files is loaded into the This feature allows you to program an MP3 disc to

TV/DVD, press DISC MENU to display the MP3 play in a desired sequence.

menu on the TV screen.

In stop mode, press MODE.

¡The PROGRAM screen will appear.

In stop mode, press Arrow (K/L) to select

the desired group or

Select a desired track using Arrow

(K/L/s/B). Then, press ENTER.

track.

folder name 1

¡If a group is selected, press

folder name 2

folder name 3

folder name 4

file name 1

file name 2

file name 3

or ENTER to go on to the

track selection screen. Press

Arrow (K /L ) to choose a

track, then press ENTER.

¡If a track is selected, press ENTER to start playing

tracks. Starting from the one you’ve just chosen the

subsequent tracks will be played.

¡Press B when you want to go to the next hierarchy.

¡Press s when you want to go back to the previous

hierarchy.

¡Press CLEAR to erase the most recently entered pro-

gram.

folder name 1

Repeat step 2 until you have selected all the

tracks you want to play in the program.

¡Press TITLE to return to the first item.

Press PLAY to start programmed playback.

NOTES

Press STOP to stop playback.

¡While the program is being played back, the STOP

works as follows.

¡Press STOP once and then PLAY again, playback

will restart from the point where STOP was pressed.

(Program continued)

¡Press STOP twice and then PLAY again, playback will

restart from the first track. (Program cleared)

¡To erase all programs at once, select ALL CLEAR at

the bottom of the list at Step2.

NOTES

¡Folders are known as Groups; files are known as

Tracks.

¡MP3 files are accompanied by

¡Maximum of 255 folders can be recognized.

¡Maximum of 512 files can be recognized.

¡Up to 8 hierarchies can be created.

This TV/DVD recommends the use of files recorded at

the below specifications:

icon.

¡Sampling frequency: 44.1kHz or 48kHz

¡Constant bit rate: 112kbps ~ 320kbps.

RANDOM PLAYBACK

MP3

REPEAT

REPEAT is available only during playback.

In stop mode, press MODE twice.

¡RANDOM screen appears.

MP3

Press PLAY to start random playback.

To activate the repeat function, press REPEAT

during playback.

¡The repeat mode changes as described below every

time you press the button.

TRACK

(current track

repeat)

GROUP

(current group

repeat)

ALL

(entire disc

repeat)

OFF

(repeat off)

NOTE

¡Repeat setting will be cleared when moving to other

track.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

CHANGING THE SETTINGS

SUBTITLE LANGUAGE

CAMERA ANGLE

DVD-V

The TV/DVD allows you to select a language for sub- Some DVD discs contain scenes which have been shot

titles during DVD disc (if available) playback. simultaneously from various angles. You can change

the camera angle when the (

screen.

) icon appears on the

Press SUBTITLE during playback.

Press SUBTITLE repeatedly to select your

desired subtitle language.

Press ANGLE during playback.

¡The selected angle will be displayed on the display

¡The subtitle language will be displayed on the dis-

play bar at the top of the screen.

bar at the top of the screen.

Press ANGLE repeatedly to select your

desired angle.

To turn off subtitles, press SUBTITLE

repeatedly until OFF appears.

NOTES

Some discs allow audio language setting/subtitle language

BLACK LEVEL SETTING

setting on the disc menu. (Operation varies between discs,

so refer to the manual accompanying the disc.)

DVD-V

¡If the desired language is not shown after pressing

SUBTITLE several times, the disc does not have

subtitles in that language.

Adjust the Black Level Settings to make the black

parts of the picture brighter.

¡If you choose a Language that has a 3 letter language

code, the code will be displayed every time you

change the Subtitle language setting. If you choose

any other languages, ‘---’ will be displayed instead.

(Refer to page 27.)

Press MODE during playback.

OFF

Press ENTER to switch ON/OFF.

ON: Makes the dark parts brighter.

AUDIO LANGUAGE

OFF: Shows the original picture as recorded.

DVD-V

Press MODE twice or RETURN to exit.

NOTE

The TV/DVD allows you to select a language during

DVD disc (if multi languages are available) playback.

¡The setting will be saved even if the TV/DVD is

turned off.

Press AUDIO during playback.

VIRTUAL SURROUND

Press AUDIO repeatedly to select your

desired language.

DVD-V

MP3

NOTE

¡Pressing AUDIO may not work on some DVDs with

multiple audio languages (e.g. DVDs which allow

audio language setting on the disc menu).

You can enjoy surround-sound effect over two speak-

ers on this TV/DVD.

Press V.SURR once or MODE twice

(CD/MP3: once) during playback.

STEREO SOUND MODE

OFF

Press AUDIO repeatedly during playback to

select between STEREO, L-CH or R-CH.

Press ENTER to set it 1 (Natural effect) or 2

(Emphasized effect) or OFF.

¡STEREO - both right and left channels are active

(stereo)

L-CH - only left channel is active

R-CH - only right channel is active

NOTE

¡If the Virtual Surround setting is ON, the sound

mode will be fixed to STEREO, and can not be

changed.

Press V.SURR or MODE or RETURN to exit.

NOTE (for CD play only)

¡Virtual Surround will not be effective if the sound

mode is set to something other than STEREO.

–

_{Download from Www.Somanuals.co}2_m5_{. All Manuals Search And Download.}

0C28

THE ON-SCREEN INFORMATION

DVD-V

MP3

You can check the information about the current disc by pressing DISPLAY on the remote control.

For DVD-Vs

For audio CDs

Press DISPLAY during playback to show

current Chapter.

Press DISPLAY during playback to show the

current Track.

¡The elapsed and remaining

playing time of the current

chapter will be displayed.

¡The elapsed and remaining playing time of the cur-

rent track will be displayed.

9/49

0:00:00 -0:03:30

Press DISPLAY again to show current Total

Track.

Press DISPLAY again to show current Title.

¡The elapsed and remaining playing time of the cur-

rent track will be displayed.

rent title will be displayed.

Press DISPLAY again.

¡The BIT RATE and the current repeat setting will be

displayed.

Press DISPLAY again to exit the display.

¡If you are playing a dual layered disc, the layer num-

ber will also be displayed (L0: Layer 0 is playing.

L1: Layer 1 is playing).

For MP3

Press DISPLAY during playback.

¡The name of the file currently in play will be dis-

Press DISPLAY again to exit the display.

played.

Press DISPLAY again to show the track

number, the elapsed time, the repeat status,

and the playback status at the top of the

screen.

will be displayed when repeat play has been

selected.

T - indicates Track repeat

G - indicates Group (folder) repeat

A - indicates Disc repeat

Press DISPLAY again to exit the display.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

CHANGING THE DVD SETUP ITEMS

LANGUAGE SETTING

Language

Code Language

Code

DVD-V

A-B

L-N

Abkhazian

Afar

Afrikaans

Albanian

Amharic

Arabic

Armenian

Assamese

Aymara

Azerbaijani

Bashkir

Basque

Bengali;Bangla

Bhutani

Bihari

Bislama

Breton

4748 Laothian

4747 Latin

4752 Latvian;Lettish

6563 Lingala

4759 Lithuanian

4764 Macedonian

5471 Malagasy

4765 Malay

4771 Malayalam

4772 Maltese

4847 Maori

5861

5847

5868

5860

5866

5957

5953

5965

5958

5966

5955

5964

5961

5960

6047

6051

6061

Language options are not available with some discs.

Press SETUP twice in STOP mode so that

the DVD SETUP menu appears.

¡If the menu does not appear, press PLAY, STOP,

then SETUP twice.

5167 Marathi

SETUP

4860 Moldavian

5072 Mongolian

4854 Nauru

4855 Nepali

4864 Norwegian [NOR]

4853

5971 Occitan

4851 Oriya

Oromo(Afan)

5759 Panjabi

4947 Pashto;Pushto

7254 Persian

4961 Polish

5464 Portuguese [POR]

4965 Quechua

5047 Rhaeto-Romance

6058 Romanian [RUM]

5160 Russian [RUS]

5161

5166 Samoan

Sangho

5261 Sanskrit

5256 Scots Gaelic

5255 Serbian

5264 Serbo-Croatian

5271 Sesotho

5358 Setswana

5747 Shona

QUICK

CUSTOM

INITIALIZE

Bulgarian

Burmese

Byelorussian

O-R

6149

6164

6159

6247

6265

5247

6258

6266

6367

6459

6461

6467

Press Arrow L to select “CUSTOM”, then

C-E

press ENTER.

Cambodian

Catalan

Chinese [CHI]

Corsican

Croatian

¡CUSTOM mode will appear.

Press Arrow (K/L) to select “LANGUAGE”,

Czech

then press ENTER to confirm.

Danish [DAN]

Dutch [DUT]

English [ENG]

Esperanto

Estonian

SETUP

CUSTOM

6559

6553

6547

5350

6564

6554

6566

6660

6560

6550

6555

6565

6557

6558

6561

5165

6567

6569

6568

LANGUAGE

DISPLAY

AUDIO

F-H

Faroese

Fiji

Finnish [FIN]

French [FRE]

Frisian

PARENTAL

Press Arrow (K/L) to select the next items,

Galician

then press ENTER.

Georgian

German [GER]

Greek [GRE]

Greenlandic

Guarani

Gujarati

Hausa

Hebrew

Hindi

Hungarian [HUN]

I-K

Icelandic [ICE]

Indonesian

Interlingua

Interlingue

Inupiak

Irish [IRI]

Italian [ITA]

Japanese [JPN]

Javanese

Kannada

Kashmiri

5051 Sindhi

AUDIO: Sets the audio language.

5158 Singhalese

5758 Siswat

5360 Slovak

5367 Slovenian

5447 Somali

5569 Spanish [SPA]

5455 Sundanese

5467 Swahili

SUBTITLE: Sets the subtitle language.

DISC MENU: Sets the language for DVD menu.

Press Arrow (K/L) to select a setting, then

press ENTER.

Swedish [SWE]

¡If OTHER is selected on the AUDIO, SUBTITLE or

DISC MENU screen, press four-digit number to

enter the code for the desired language. (Refer to the

language code list.)

¡Only the languages supported by the disc can be

selected.

5565

5560 Tagalog

5547 Tajik

5551 Tamil

5557 Tatar

5347 Telugu

5566 Thai

5647 Tibetan

5669 Tigrinya

5760 Tonga

5765 Tsonga

5757 Turkish [TUR]

6469 Turkmen

5771 Twi

6658

6653

6647

6666

6651

6654

4861

6655

6661

6665

6664

6657

6669

Press SETUP to exit.

Kazakh

NOTE

Kinyarwanda

Kirghiz

Kirundi

Korean [KOR]

Kurdish

¡Language Setting for Audio and Subtitle is not avail-

able with some discs. Then use the AUDIO and the

SUBTITLE button. Details are on page 25.

6460

U-Z

5761 Ukrainian

5767 Urdu

Uzbek

6757

6764

6772

6855

6861

4971

6961

7054

5655

7161

7267

Vietnamese

Volapuk

Welsh

Wolof

Xhosa

Yiddish

TO CHANGE THE ON-SCREEN MENUS

You can access the TV SETUP menu by pressing

SETUP from the DVD mode. Refer to “Selecting the

Language” on page 13 to changing the on-screen

menus.

Yoruba

Zulu

If you choose a Language that has a 3 letter language

code, the code will be displayed every time you change

the Audio or Subtitle language setting on page 25. If

you choose any other languages, ‘---’ will be displayed

instead. (3 letter language code is written in bracket.)

–

_{Download from Www.Somanuals.co}2_m7_{. All Manuals Search And Download.}

0C28

DISPLAY SETTING

AUDIO SETTINGS

DVD-V

You can change certain aspects of the DVD display

screens and on-screen messages on the TV screen.

Choose the appropriate Audio settings for your equip-

ment as it only affects during the playback of DVD

discs.

Press SETUP twice in STOP mode so that

the DVD SETUP menu appears.

Press SETUP twice in STOP mode so that

the DVD SETUP menu appears.

¡If the menu does not appear, press PLAY, STOP,

then SETUP twice.

¡If the menu does not appear, press PLAY, STOP,

then SETUP twice.

SETUP

QUICK

CUSTOM

INITIALIZE

QUICK

CUSTOM

INITIALIZE

Press Arrow L to select “CUSTOM”, then

press ENTER.

Press Arrow L to select “CUSTOM”, then

press ENTER.

¡CUSTOM mode will appear.

Press Arrow (K/ L) to select “DISPLAY”,

then press ENTER to confirm.

Press Arrow (K/ L) to select “AUDIO”, then

press ENTER to confirm.

SETUP

CUSTOM

LANGUAGE

DISPLAY

AUDIO

SETUP

CUSTOM

PARENTAL

LANGUAGE

DISPLAY

AUDIO

Press Arrow (K/L) to select the below

items, then press ENTER.

PARENTAL

TV MODE:

QUICK

Press Arrow (K/L) to select the below

items, then press ENTER.

¡Press Arrow (K/L) for an item selection, then press

ENTER.

¡Select 4:3 LETTER BOX for black bars to appear on

top and bottom of the screen.

DRC (Dynamic Range Control):

¡To compress the range of the difference between

loud and soft sounds.

¡Select 4:3 PAN & SCAN for a full height picture

with both sides trimmed.

¡The default setting is ON.

¡The default setting is 4:3 LETTER BOX.

STILL MODE:

DOWN SAMPLING:

¡Set to ON when outputting a 48 kHz signal.

¡The default setting is ON.

When playing disc with copyright Protection

¡If you select OFF, copyright protection will be acti-

vated and sound will be down sampled at 48kHz.

¡Press Arrow (K/L) for an item selection, then press

ENTER.

¡Select “AUTO” usually.

¡If you select “FIELD”, the picture in the still mode

will be stable.

¡If you select “FRAME”, the picture in the still mode

will be highly defined.

DOLBY DIGITAL:

QUICK

ANGLE ICON:

Set to ON when the unit is connected to an

amplifier/receiver with a Dolby Digital Decoder.

ON: Outputs a Dolby Digital signal

OFF: Converts the Dolby Digital signal into a PCM

(2 channel stereo)

¡Press ENTER repeatedly to turn Angle icon ON or

OFF.

¡The default setting is ON.

AUTO POWER OFF:

¡Press ENTER repeatedly to turn Auto Power off ON

¡The default setting is ON.

or OFF.

The default setting is ON and it will turn the TV/DVD

off automatically after 15 minutes of no use.

Press SETUP to exit.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

CONTROL LEVELS

PARENTAL CONTROL

ALL

All parental lock is cancelled.

DVD-V

Level 8

DVD software of any grade (adult/general/children)

can be played back.

Parental Control limits the disc viewing that exceed

your settings. This feature allows you to prevent discs

with objectionable scenes from being played by your

children.

Levels 7 to 2

Only DVD software intended for general use and

children can be played back.

Level 1

PARENTAL LEVEL

Only DVD software intended for children can be

played back, with those intended for adult and

general use is prohibited.

Parental Level allows you to set the rating level of

your DVD discs. Playback will stop if the disc’s rat-

ings exceed the level you select.

Press SETUP twice in STOP mode so that

the QUICK SETUP menu appears.

IF YOU FORGET THE PASSWORD

¡If the menu does not appear, press PLAY, STOP,

then SETUP twice.

Press 4, 7, 3, 7 at step 4. Then enter your

new password.

¡Password will be cleared and parental level will be

SETUP

set to ALL.

QUICK

CUSTOM

INITIALIZE

Follow Steps [5]-[7] again.

Press Arrow L to select “CUSTOM”, then

press ENTER.

INITIALIZE

This allows you to return all selections of SETUP

(except for PARENTAL) to their default settings.

Press Arrow (K/L) to select “PARENTAL”,

then press ENTER.

Press SETUP twice in STOP mode so that

the INITIALIZE menu appears.

SETUP

CUSTOM

LANGUAGE

DISPLAY

AUDIO

Press Arrow (K/L) to select “INITIALIZE”,

then press ENTER.

PARENTAL

Select “YES”, then press ENTER twice. All

the settings (except for “PARENTAL”) will be

cleared.

Enter your four-digit password then press

ENTER.

¡To cancel the initialization, select “NO”.

Press Arrow (K/L) to select PARENTAL

LEVEL, then press ENTER.

Press SETUP to exit.

Press Arrow (K/L) to select the desired

level.

Press SETUP to exit

NOTES

¡When doing this for the first time, enter any 4 digits.

(except for 4737) That number will be used as the

default password from the second time onward.

¡To change the password, press Arrow (K/L) to

select CHANGE at step 5, then press ENTER. Enter

the four-digit password, then press ENTER.

¡With some DVDs, it may be difficult to find if they

are compatible with parental lock. Be sure to check

if the parental lock function operates in the way that

you have set for each DVD disc in question.

¡Record the password in case you forget it.

–

_{Download from Www.Somanuals.co}2_m9_{. All Manuals Search And Download.}

0C28

TROUBLESHOOTING GUIDE

If the TV/DVD does not perform properly when operated as instructed in this Owner’s Manual, check the

TV/DVD, consulting the following checklist.

Problem

Corrective Action

No power

Make sure the power plug is connected to an AC outlet.

Make sure the power is turned on.

Check if the power plug is connected to an AC outlet.

Check the batteries in the remote control.

•

The TV/DVD does not respond to

the remote control.

•

Aim the remote control directly at the remote sensor. If necessary,

remove all the obstacles between the sensor and the remote.

You have to be within 23 feet of the TV/DVD.

•

Check if the correct mode is selected. If not switch the mode by

pressing SELECT on the remote control,whichever you need.

TV Mode

Problem

Corrective Action

No Picture or Sound

• ^{Try a new channel, if OK, then possible station trouble.}

• ^{Make sure the power is turned on.}

• ^{Press SELECT on the remote control to select TV mode. Then try}

• ^o^Is^th^a^enr^te^Tⁿ^V^na^fe^o^a^r^tu^c^r^a^e^b^.^{le connected to terminal on the back of the set?}

• ^{If outside antenna is being used, check for broken wire.}

Bars On Screen

• ^{Check for local interference}

• ^{Check incoming CATV cable for loose or bad connections.}

Picture Distorted or Blurred

• ^{Try a new channel, if OK, then possible station trouble.}

• If outside antenna is being used, check for broken wire.

• ^{Check incoming CATV cable for loose or bad connections.}

Picture Rolls Vertically

Lines or Streaks in Picture

• ^{Try a new channel, if OK, then possible station trouble.}

• ^{If outside antenna is being used, check for broken wire.}

• ^{Check for local interference.}

• ^{Check incoming CATV cable for loose or bad connections.}

No Color

• ^{Try a new channel, if OK, then possible station trouble.}

• ^{Is antenna or cable connected to terminal on the back of the set?}

• ^{If outside antenna is being used, check for broken wire.}

• ^{Adjust COLOR control.}

• ^{Check incoming CATV cable for loose or bad connections.}

Poor Reception on Some Channels • ^{Try a new channel, if OK, then possible station trouble.}

Ghosts in Picture

• ^{Is antenna or cable connected to terminal on the back of the set?}

• If outside antenna is being used, check for broken wire.

• ^{Check for local interference.}

• ^{Check incoming CATV cable for loose or bad connections.}

Weak Picture

• ^{Try a new channel, if OK, then possible station trouble.}

• ^{Is antenna or cable connected to terminal on the back of the set?}

• ^{If outside antenna is being used, check for broken wire.}

• ^{Adjust CONTRAST & BRIGHT control.}

• ^{Check incoming CATV cable for loose or bad connections.}

Sound OK, Picture Poor

• ^{Try a new channel, if OK, then possible station trouble.}

• ^{Is antenna or cable connected to terminal on the back of the set?}

• ^{If outside antenna is being used, check for broken wire.}

• ^{Check for local interference.}

• ^{Adjust CONTRAST & BRIGHT control.}

Picture OK, Sound Poor

• Try a new channel, if OK, then possible station trouble.

• Check for local interference.

Different color marks on screen

• ^{Magnetism from nearby unsealeded speakers or appliances might}

affect the color of the TV picture. Move the TV/DVD away from the

speakers or appliances. The TV/DVD can repair itself automatically

by unplugging the TV/DVD power cord, and then plug it in again 30

minutes or so later.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

Closed Caption Problem

My TV/DVD is showing captions

that are misspelled.

Possible Remedy

• You are watching a live broadcast and spelling errors made by the

• closed captioning production company may pass through uncorrected.

• A prerecorded program will not show any misspelled words because

• of the time available for editing the captions.

My TV/DVD will not show the text • Captions that are delayed a few seconds behind the actual dialogue

in its entirety or there is a delay of • are common for live broadcast. Most captioning production companies

what is being said.

• can display a dialogue to a maximum of 220 words per minute. If a

• dialogue exceeds that rate, selective editing is used to insure that the

• captions remain up-to-date with the current TV screen dialogue.

• Interference caused by building, power lines, thunderstorms, etc.

• may cause scrambled or incomplete captions to appear.

My captions are scrambled with

white boxes on the TV screen.

My program guide listed a TV show • Broadcasters may at times use a time compression process to the

as being closed captioned but none • actual program so that additional advertising time can be given.

of the captions were displayed.

• Since the decoder cannot read the compressed information,

• captions will be lost.

My TV/DVD screen shows a black • You are in the TEXT mode. Select CAPTION mode or CAPTION

box on certain channels.

• [OFF].

DVD Mode

Problem

Corrective Action

No picture

• Insert a correct video disc that plays on this TV/DVD.

• Press SELECT on the remote control to select DVD mode. Next,

press PLAY or OPEN/CLOSE. Then, try other DVD feature.

• Insert the disc.

Disc cannot be played

No sound

• Clean the disc.

• Place the disc correctly, with the label side up.

• Cancel the parental lock or change the control level.

• Connect the audio cables firmly.

• Turn the power of the audio component on.

• Correct the audio output settings.

• Correct the input settings on the audio component.

• This TV/DVD does not support DTS audio. This is not a malfunction.

• There are some cases where pictures may be slightly distorted, which

are not a sign of a malfunction.

No DTS audio is output

Distorted picture

• Although pictures may stop for a moment, this is not a malfunction.

• The selected language is not available for audio or subtitles on the

DVD disc.

Audio or subtitle language

does not match the set up

This is not a malfunction

The camera angle cannot be

changed

• The DVD disc does not contain sequences recorded from different

camera angles. This is not a malfunction

Audio or subtitle language cannot

• The DVD disc does not contain audio source or subtitles in the

selected language. This is not a malfunction.

• That operation is prohibited by the TV/DVD or the disc.

This is not a malfunction.

• Scratched disc. Replace the disc with unscratched one.

• Dirty disc. Replace or cleaw disc.

be changed

“Prohibited icon” appears on the

screen, prohibiting an operation

CD sound dropout

No CD reproduction

DVD picture dropout

DVD picture freeze

DVD picture in mosaic

No DVD reproduction

NOTES:

Some functions are not available in specific modes, but this is not a malfunction. Read the description in

this Owner’s Manual for details on correct operations.

•

Playback from a desired track and random playback are not available during program playback.

•

–

_{Download from Www.Somanuals.co}3_m1_{. All Manuals Search And Download.}

0C28

MAINTENANCE

CABINET CLEANING

SERVICING

Wipe the front panel and other exterior surfaces of

the TV/DVD with a soft cloth immersed in luke-

warm water and wrung dry.

Never use a solvent or alcohol. Do not spray insec-

ticide liquid near the TV/DVD. Such chemicals

may cause damage and discoloration to the

exposed surfaces.

Should your TV/DVD become inoperative, do not

try to correct the problem by yourself. There are no

user-serviceable parts inside. Turn off, unplug the

power cord, and please call our help line at 1-800-

488-1222, to locate an Authorized Service Center.

•

IF THE LASER OPTICAL PICKUP UNIT IS DIRTY

If the TV/DVD still does not perform properly when it is operated while referring to the relevant sections and to

"TROUBLESHOOTING GUIDE" in this Owner's Manual, the laser optical pickup unit may be dirty. Consult

your dealer or an Authorized Service Center for inspection and cleaning of the laser optical pickup unit.

•

DISC HANDLING

Use discs which have the following logos on them.

(Optical audio digital discs.)

•

To clean-off, use a soft cloth.

Do not use a hard cloth since this will mar the disc.

Wipe the disc in a straight line from center to edge.

Never wipe with a circular motion.

•

ReWritable

Recordable

Do not use detergent or abrasive cleaning agents.

Handle the discs so that fingerprints and dust do

not adhere to the surfaces of the discs.

•

Always store the disc in its protective case when it

is not used.

•

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

SPECIFICATIONS

GENERAL SPECIFICATIONS

ELECTRICAL SPECIFICATIONS

Sound output:

2 speakers, 1W, 8 ohm

CRT :

20 inch in-line gun,

90˚ deflection tube

NTSC-M

OTHER SPECIFICATIONS

Terminals

Television system:

Antenna input:

VHF/UHF/CATV

TV Standard

75 ohm unbalanced (F-type)

RCA connector [ 1

RCA connector [ 2

Closed caption system: §15.119/FCC

Channel coverage:

Video input:

Audio L/R input:

Headphone:

Coaxial digital

audio output

(DVD, CD, MP3

Audio only):

VHF:

UHF:

CATV:

2 ~ 13

14 ~ 69

2 ~13, A ~ W,

W+1 ~ W+84,

A-5 ~ A-1, 5A

181 channel

1/8” stereo (3.5 mm)

One pin jack,

500m Vpp (75 ohm)

Digital encoded

Tuning System:

Channel access:

frequency synthesized

tuning system

Direct access keyboard,

programmable

scan and up/down

Remote control:

infrared light system

Operating

temperature:

5°C to 40°C

(41°F~104°F)

Power requirements: AC 120V, 60Hz

Power consumption

(Maximum) :

Dimensions :

80W

H:20-3/16”(514mm)

W:20-3/16”(512mm)

D:19-13/16”(503mm)

49.6lbs(21.0kg)

DVD

Discs:

DVD video, Audio CD

Weight :

Output signal format: NTSC color

Designs and specifications are subject to change without notice.

If there is a discrepancy between languages, the default language will be English.

•

–

_{Download from Www.Somanuals.co}3_m3_{. All Manuals Search And Download.}

0C28

9. Botón SKIP

INDICE

Reproduce desde el inicio del capítulo o canción actual.

Botón SEARCH (REV) h (panel delantero)

Durante la reproducción o en el modo de pausa,

mantenga presionado el botón durante unos segundos

para cambiar la velocidad de reproducción hacia atrás.

■ CONTROLES DE OPERACIÓN Y FUNCIONES . . . . . 34

PANEL FRONTAL DEL TELEVISOR/DVD. . . . . . . . . . 34

MANDO A DISTANCIA. . . . . . . . . . . . . . . . . . . . . . . . . 34

VISTA POTERIOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

PARA INSERTAR LAS PILAS . . . . . . . . . . . . . . . . . . . . 35

■ PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 35

CONEXIONES DE ANTENA/CABLE . . . . . . . . . . . . . . 35

CONEXIÓN A TOMAS DE ENTRADA EXTERNA. . . . 36

CONEXIÓN A UN AMPLIFICADOR EQUIPADO

10. Botón PLAY

Inicia la reproducción del contenido del disco.

Púlselo para cambiar a un modo de DVD cuando esta

en el modo de televisor.

11. Botón SKIP

CON TOMAS DE ENTRADA DIGITAL, PLATINA

MD O PLATINA DAT (Para DVD) . . . . . . . . . . . . . . . . . 36

CONEXCIONA UN DECODIFICADOR DOLBY

Reproduce desde el inicio del siguiente capítulo o

canción.

Botón SEARCH (FWD) g (panel delantero)

Durante la reproducción o en el modo de pausa,

mantenga presionado el botón durante unos segundos

para cambiar la velocidad de reproducción en avance.

DIGITAL (Para DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

TV SECTION

■ PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 37

SELECCIÓN DE IDIOMA . . . . . . . . . . . . . . . . . . . . . . . 37

AJUSTE DE CANAL . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

12. Botón PAUSE

Hace una pausa en la operación del disco.

13. Botón OPEN/CLOSE

Púlselo para insertar discos en la bandeja o retirarlos

de ella.

DVD SECTION

■ REPRODUCCIÓN DE UN DVD DE VÍDEO O UN

CD DE AUDIO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

REPRODUCCION BASICA . . . . . . . . . . . . . . . . . . . . . . 38

14.Toma HEADPHONE

Para conectar auriculares (no suministrados) y

escuchar en privado.

CONTROLES DE

15. Botón MODE

Activa el modo de reproducción programada o el

modo de reproducción aleatoria cuand se reproducen

CDs o MP3.

OPERACIÓN Y FUNCIONES

PANEL FRONTAL DEL

TELEVISOR/DVD

16. Botones de números

Modo del televisor:

Pulse dos dígitos para tener acceso directamente al

canal deseado.

Consulte la figura 1 de la página 8

Recuerde pulsar "0" antes de elegir un canal de un

solo dígito.

MANDO A DISTANCIA

Botón +100

Púlselo para seleccionar canales de televisión por

cable cuyo número sea igual o superior al 100.

Modo DVD:

Consulte la figura 2 de la página 8

VISTA POSTERIOR

Púlselo para introducir el número deseado.

Botón +10

Púlselo para introducir los números deseados cuyo

número sea igual o superior al 10.

17. Botón SLEEP

Consulte la figura 3 de la página 9

1. Bandeja de carga del disco

2.Toma de entrada VIDEO

Pulse el botón SLEEP para visualizar el temporizador

para dormir y activar la función. La hora de apagado

puede determinarse por el número de veces que usted

pulsa el botón. (0, 30, 60, 90 o 120 minutos)

Conecte aquí la toma de salida de vídeo de una

videocámara o de una videograbadora.

3.Tomas de entrada AUDIO L/R

18. Botón REV

Conecte aquí las tomas de salida de audio de una

videocámara o de una videograbadora.

Presione para ver la imagena en DVD en retroceso

rápido. Presione PAUSE y presione este botón para

empezar la reproducción en cámara lenta. Presione

repetidamente este botón para cambiar la velocidad en

avance de la cámara lenta.

4. Botón POWER

Púlselo para conectar y desconectar la alimentación.

5. Botones VOLUME o/p(VOL.m/n)

Púlselos para controlar el nivel del volumen para el

DVD y el televisor.

Botón FWD

Presione para avanzar rápidamente en el disco.

Presione PAUSE y presione este botón para empezar

la reproducción en cámara lenta. Presione

repetidamente este botón para cambiar la velocidad

de avance de la cámara lenta.

6. Botones CHANNEL o/p(CH.o/p)

Púlselo para seleccionar el canal memorizado.

Púlselo para cambiar a un modo de televisor cuando

esta en el modo de DVD.

7. Ventanilla del sensor del mando a distancia

19. Botón V.SURR

8. Botón STOP

Púlselo para activar/desactivar el envolvente virtual.

Detiene la operación del disco.

20. Botón SETUP

Púlselo para activar o salir del modo de menús de

televisor o preparación de DVD.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

21. Botón TITLE

37. Cable de alimentaciónConéctelo a una toma de

CA convencional (120 V/60 Hz).

Visualiza el menú de títulos.

NOTA: Retire el cable de alimentación del gancho

para evitar romperlo antes de conectarlo a una

toma de CA convencional.

22. Botón CLEAR

Repone un ajuste.

23. Botón DISPLAY

38.Toma de salida de audio digital COAXIAL

(DVD Audio solamente)

Modo del televisor:

Púlselo para visualizar el número del canal en la

pantalla. Si lo pulsa de nuevo, el número del canal

desaparecerá.

Conéctela a la entrada digital de un amplificador o

decodificador externo.

Modo de DVD:

Visualiza el estado actual en la pantalla del televisor

con fines de comprobación.

39.Toma de entrada ANT.

Conéctela a una antena, sistema de televisión por

cable o sistema de satélite.

24. Botón SEARCH MODE

Púlselo para localizar un punto deseado.

25. Botón AUDIO

PARA INSERTAR LAS PILAS

1) Abra la cubierta del compartimiento de las pilas

empujando la cubierta del mando a distancia en el

sentido de la flecha.

2) Inserte 2 pilas "AA" en el compartimiento de las

pilas, en el sentido indicado por las marcas de

polaridad (+/-).

Púlselo para seleccionar un idioma de audio o un

modo de sonido deseado.

26. Botón SUBTITLE

Púlselo para seleccionar un idioma de subtítulos

deseado.

27. Botón REPEAT

Repite la reproducción del disco, título, capítulo o

pista actual.

3) Vuelva a poner la cubierta.

28. Botón ANGLE

NOTAS:

Púlselo para cambiar el ángulo de la cámara y ver,

desde un ángulo diferente, la secuencia que está

siendo reproducida.

No mezcle pilas alcalinas y de manganeso.

•

No mezcle pilas viejas y nuevas.

•

29. Botón A-B REPEAT

Repite la reproducción de una sección seleccionada.

30. Botón RETURN

PREPARACIÓN PARA LA

UTILIZACIÓN

Vuelve a la operación anterior en el modo de

instalación del DVD.

31. Botón ENTER

Púlselo para establecer un ajuste.

CONEXIONES DE

ANTENA/CABLE

32. Botones de flechas

Modo de televisor:

Púlselo para seleccionar un modo de ajuste desde el

menú que aparece en la pantalla del televisor.

Púlselo para seleccionar o ajustar desde un menú

particular.

Consulte la figura 4 de la página 10

Nota para el instalador de sistemas CATV

Esta nota tiene la finalidad de llamar la atención del

instalador de sistemas CATV para que tenga en

cuenta el Artículo 820-40 del NEC, el cual

proporciona consejos para hacer una conexión a

tierra apropiada y, en particular, especifica que la

tierra del cable deberá estar conectada al sistema de

puesta a tierra del edificio, tan cerca del punto de

entrada del cable como sea posible.

Modo de DVD:

Se utiliza cuando se hacen ajustes mientras se

observa la visualización en una pantalla de televisor.

33. Botón DISC MENU

Visualiza menús en el DVD.

34. Botón SELECT

Púlselo para cambiar a un modo de televisor, modo

de entrada externa o modo de DVD.

NOTA: Cuando seleccione el modo DVD con

este botón, pulse primero PLAY u

NOTA:

Antes de enchufar la antena a la toma ANT.IN del

televisor/DVD, compruebe que la clavija no esté

doblada. Si esta doblada, póngala derecha como se

muestra en la ilustración, y luego conéctela en la

toma ANT.IN del televisor/DVD.

Clavija doblada

OPEN/CLOSE. De lo contrario, las funciones del

DVD no se activarán.

35. Botón MUTE

Pulse el botón MUTE para apagar el sonido de un

programa de TV. (La visualización del nivel del

sonido cambia de ROJO CLARO a AZUL CLARO.)

Pulse de nuevo el botón MUTE o el botón VOL m o

n para restaurar el sonido.

Cable

Clavija

(Necesita enderezarse)

(Clavija derecha)

36. Botón PICTURE

Presione para entrar en el modo de ajuste de imagen.

ANTENA COMBINADA DE VHF/UHF

La antena combinada de VHF/UHF de 75 ohmios

puede conectarse al terminal ANT.

–

_{Download from Www.Somanuals.co}3_m5_{. All Manuals Search And Download.}

0C28

NOTA:

Cuando conecte una videograbadora monofónica

(otra fuente) a este televisor/DVD, conecte la toma

de salida de audio de la videograbadora

ANTENA SEPARADAS DE VHF/UHF

En algunas zonas será necesario utilizar una antena

exterior.

•

TELEVICION POR CABLE SIN CAJA

DE CONVERTIDOR / DECODIFICADOR

Utilice esta conexión si su sistema de televisión por

cable se conecta directamente a su televisor/DVD sin

una caja de convertidor. Utilice el mando a distancia

del televisor/DVD para seleccionar los canales.

monofónica (otra fuente) a la toma AUDIO L de

este televisor/DVD. El audio saldrá igualmente por

los canales izquierdo y derecho.

Consulte la figura 5 de la página 11

TELEVICION POR CABLE CON CAJA

DE CONVERTIDOR/DECODIFICADOR

O CAJA DE SATRLITE

CONEXIÓN A UN

AMPLIFICADOR EQUIPADO

CON TOMAS DE ENTRADA

DIGITAL, PLATINA MD O

PLATINA DAT (Para DVD)

Si su compañía de televisión por cable le suministra

una caja de convertidor, o si usted utiliza un sistema

de satélite, usted podrá utilizar la conexión básica

mostrada aquí.

La selección de los canales deberá hacerse con la caja

de convertidor o con la caja de satélite. Esto significa

que los canales no se podrán cambiar utilizando el

mando a distancia del televisor/DVD.

Utilice un cable digital coaxial de audio de venta en

el comercio especializado para hacer las conexiones

de audio.

Consulte la figura 6 de la página 11

NOTAS:

PARA VER UN CANAL

CODIFICADO/DECODIFICADO

1) Ponga el selector de canales del televisor/DVD

en la posición del canal de salida de la caja de

convertidor de televisión por cable o de la caja de

satélite. (Ej., CH3)

La fuente de audio de un disco en un formato de

•

sonido ambiental Dolby Digital de 5,1 canales no

se puede grabar como sonido digital mediante una

platina MD o DAT.

2) Seleccione el canal que va a ver en su caja de

convertidor de televisión por cable o caja de

satélite.

Asegúrese de desconectar la alimentación de todos

los componentes antes de conectar otro

componente.

Consulte los manuales del propietario de los

componentes que va a conectar al televisor/DVD.

•

CONEXIÓN A TOMAS DE

ENTRADA EXTERNA

Ponga DOLBY DIGITAL en OFF para la salida de

•

audio en el modo de preparación. La reproducción

en un televisor/DVD utilizando ajustes incorrectos

puede causar distorsión de ruido, y también se

pueden dañar los altavoces. (Consulte la página 28

para poner DOLBY DIGITAL en OFF.)

Cuando vea un programa grabado en otra fuente

(videograbadora o videocámara), utilice las tomas de

entrada de audio/vídeo de la parte delantera del

televisor/DVD.

Conecte las tomas de salida de audio/vídeo de otra

fuente a las tomas AUDIO L/R y VIDEO de este

televisor/DVD. Luego pulse SELECT hasta que

aparezca "AUX" en la pantalla.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

CONEXCIONA UN

DECODIFICADOR DOLBY

DIGITAL (Para DVD)

TV SECTION

PREPARACIÓN PARA LA

UTILIZACIÓN

Si utiliza este televisor/DVD para reproducir un disco

DVD en un formato de sonido ambiental Dolby

Digital de 5,1 canales, el televisor/DVD dará salida a

un flujo de datos DOLBY DIGITAL desde su toma

de salida de audio digital COAXIAL. Conectando el

reproductor a un decodificador Dolby Digital, usted

podrá disfrutar de un ambiente más convincente y

real, con un sonido ambiental potente y de alta

calidad similar al de los cines.

SELECCIÓN DE IDIOMA

1 Enchufe el cordón de alimentación

del televisor/DVD

Enchufe el cordón de alimentación del

televisor/DVD en una toma de CA están-

dar.

Utilice cables digitales coaxiales de audio disponibles

en el comercio especializado para hacer las

conexiones de audio.

NOTA:

Si aparecen algunas cifras en la esquina de la pan-

talla, pulse el botón POWER sin desenchufar el

cordón de alimentación.

•

Consulte la figura 7 de la página 12

NOTAS:

Asegúrese de desconectar la alimentación de todos

los componentes del sistema antes de conector a

otro componente.

•

Asegúrese de que ...

Pulse el botón POWER para encender el televi-

sor/DVD.

NOTA: Esta función afecta sólo el idioma en el menú

de la pantalla y no la fuente de audio.

•

Consulte los manuales del propietario de los

componentes que vaya a conectar al televisor/DVD.

Si conecta un decodificador Dolby Digital, ponga

DOLBY DIGITAL en ON para la salida de audio

en el modo de preparación. (Consulte la página 28

para poner DOLBY DIGITAL en ON.)

•

- TV SETUP -

2 Seleccione “LANGUAGE”

CHANNEL SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

A menos que se haga la conexión a un

Pulse el botón SETUP en el mando

•

decodificador Dolby Digital , ponga DOLBY

DIGITAL en OFF para la salida de audio en el

modo de preparación. La reproducción en el

televisor/DVD utilizando ajustes incorrectos puede

generar distorsión de ruido, y también puede

estropear los altavoces.

a distancia.

Pulse el botón K o L para señalar

“LANGUAGE”.

Seleccione “ENGLISH”, “ESPAÑOL” o “FRANÇAIS”

Seleccione “ENGLISH”, “ESPAÑOL” o

“FRANÇAIS” con el botón ENTER.

4 Salga del modo de idioma

Pulse el botón SETUP en el mando a distancia para

volver al modo del televisor.

NOTA: Si, por alguna razón, el menú está en español

o francés, pulse el botón SETUP en el mando a dis-

tancia, pulse el botón K para señalar el “IDIOMA

(ESPAÑOL)” o “LANGAGE (FRANÇAIS)”, a con-

tinuación, pulse el botón ENTER y pulse el botón

SETUP en el mando a distancia.

Fabricado bajo licencia de Dolby

Laboratories. “Dolby” y el símbolo de la D

doble son marcas de fábrica de Dolby

Laboratories.

–

_{Download from Www.Somanuals.co}3_m7_{. All Manuals Search And Download.}

0C28

AJUSTE DE CANAL

DVD SECTION

REPRODUCCIÓN DE UN

DVD DE VÍDEO O UN CD

DE AUDIO

Puede programar el sintonizador para buscar todos

los canales que recibe en su localidad.

NOTA: El canal preparado NO es necesario cuando

esté conectado a una caja de cable o caja de satélite.

Sólo tiene que seleccionar con el selector de canal del

televisor/videograbadora al canal de salida de la caja

de cabe o caja de satélite (por ejemplo el canal CH3).

Seleccione el canal a ver en la caja de cable o caja de

satélite.

REPRODUCCION BASICA

DVD-V

MP3

Para empezar

¡Conecte el interruptor del amplificador y otros

equipos, si fuera necesario.

Asegúrese de que ...

1 Pulse el boton POWER.

¡La alimentación se conectará.

Pulse el botón POWER para encender el televi-

sor/DVD.

•

1 Seleccione “AJUSTE DE CANAL”

Pulse el botón SETUP en el mando

a distancia.

Pulse el botón K o L para señalar

“AJUSTE DE CANAL”.

A continuación, pulse el botón

ENTER.

– M E N U –

2 Pulse el botón OPEN/CLOSE.

AJUSTE DE CANAL

AJUSTE DE V-CHIP

IDIOMA [ESPAÑOL]`

TITULO [OFF]

¡La bandeja de carga del disco se abrirá.

3 Ponga el dlsco en la bandeja con el lado

de la eliguta hacia arriba.

2 Empiece el prefijado automático

Pulse el botón K o L para señalar

“AUTOPROGRAMACION DE

AJUSTE DE CANAL

–

4 Pulse el botón PLAY.

AGREGAR/BORRAR (CATV)

B AUTOPROGRAMACION DE CA.

CA”.

¡La bandeja se cerrará automáticamente y la

reproducción empezará luego desde el primer

capítulo o pista del disco. Si la reproducción no

empieza automáticamente, pulse PLAY.

A continuación, pulse el botón

ENTER.

El sintonizador busca y memoriza

todos los canales activos en su localidad.

¡Cuando reproduzca un DVD que tenga grabado un

menú de títulos, el menú aparecerá en la pantalla.

3 Después de buscar

El sintonizador se detiene en el canal memorizado

más bajo.

Pulse el botón STOP para detener la repro-

ducción.

Cuando se activa AUTOPROGRAMACION DE

•

CA, donde no hay entrada de señal del televisor,

aparecerá “NO HAY SEÑAL DE TV” en la pan-

talla después de terminar la búsqueda de canales.

El televisor/DVD puede reconocer los canales de

•

TV para que sean canales de TV de antena de cable

con las condiciones de recepción. En este caso,

pruebe nuevamente con el prefijado automático en

las condiciones de recepción fina.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

MEMO

–

_{Download from Www.Somanuals.co}3_m9_{. All Manuals Search And Download.}

0C28

Get it fixed, at your home or ours!

Your Home

For repair in your home-of all major brand appliances,

lawn and garden equipment, or heating and cooling systems,

no matter who made it, no matter who sold it!

For the replacement parts, accessories and

owner's manuals that you need to do-it-yourself.

For Sears professional installation of home appliances

and items like garage door openers and water heaters.

1-800-4-MY-HOME ^R(1-800-469-4663)

Call anytime, day or night (U.S.A. and Canada)

www.sears.com

www.sears.ca

Our Home

For repair of carry-in items like vacuums, lawn equipment,

and electronics, call or go on-line for the location of your nearest

Sears Parts & Repair Center.

1-800-488-1222

Call anytime, day or night (U.S.A. only)

www.sears.com

To purchase a protection agreement on a product serviced by Sears:

1-800-827-6655 (U.S.A.)

1-800-361-6665 (Canada)

Para pedir servicio de reparación

a domicilio, y para ordenar piezas:

Au Canada pour service en français:

1-800-LE-FOYER^MC

1-888-SU-HOGAR^SM

(1-800-533-6937)

www.sears.ca

(1-888-784-6427)

Registered Trademark / ^TMTrademark / ^SMService Mark of Sears, Roebuck and Co.

Marca Registrada / ^TMMarca de Fábrica / ^SMMarca de Servicio de Sears, Roebuck and Co.

^MCMarque de commerce / ^MDMarque déposée de Sears, Roebuck and Co.

90 Day Full Warranty

If this (product) experiences any failure due to a defect in material or workmanship within 90 days from the date

of purchase, return it to your nearest Sears Parts & Repair Center, and Sears will repair it free of charge.

After 90 days and until one (1) year from the date of purchase, Sears will replace defective parts free of charge.

You pay for labor.

After 90 days and until two (2) years from the date of purchase, Sears will replace the Picture Tube if it is defec-

tive. You pay for labor.

This warranty applies only if this (product) is used for private household purposes.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179

For the location of a Sears Service Center in your area : 1-800-488-1222

Printed in China

0EMN02492

T9005UF ▲▲▲▲▲

Download from Www.Somanuals.com. All Manuals Search And Download.

Sharp Projector XG NV51XE User Manual
Shop Vac Vacuum Cleaner 86L650 User Manual
Sony CRT Television 3KD 32NX200U User Manual
Sony Digital Camera DSC H50 User Manual
Sony MP3 Player SRF X90 User Manual
Sony Stereo Receiver 3 875 814 111 User Manual
Sony Stereo System STR DE615 User Manual
Sony Video Game Headset SBH50 User Manual
Stanley Black Decker Pole Saw CS25 28 User Manual
SUPER MICRO Computer Computer Hardware RSCR2UT2E8R User Manual