Sylvania TV DVD Combo 6620LDG User Manual

If you need additional operating assistance  
after reading this owner's manual or to order  
replacement accessories, please call  
TOLL FREE : 1-800-968-3429.  
Or visit our WEB SITE at  
6620LDG (20 inch)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
14.Lightning-For added protection for this unit receiver during a  
lightning storm, or when it is left unattended and unused for  
long periods of time, unplug it from the wall outlet and dis-  
connect the antenna or cable system. This will prevent damage  
to the unit due to lightning and power-line surges.  
15.Power Lines-An outside antenna system should not be located  
in the vicinity of overhead power lines or other electric light or  
power circuits, or where it can fall into such power lines or  
circuits. When installing an outside antenna system, extreme  
care should be taken to keep from touching such power lines  
or circuits as contact with them might be fatal.  
b. If liquid has been spilled, or objects have fallen into the unit.  
c. If the unit has been exposed to rain or water.  
d. If the unit does not operate normally by following the oper-  
ating instructions. Adjust only those controls that are cov-  
ered by the operating instructions, as improper adjustment  
of other controls may result in damage and will often  
require extensive work by a qualified technician to restore  
the unit to its normal operation.  
e. If the unit has been dropped or damaged in any way.  
f. When the unit exhibits a distinct change in performance,  
this indicates a need for service.  
16.Overloading-Do not overload wall outlets and extension  
cords as this can result in a risk of fire or electric shock.  
17.Object and Liquid Entry-Never push objects of any kind  
into this unit through openings as they may touch dangerous  
voltage points or short out parts that could result in a fire or  
electric shock. Never spill liquid of any kind on the unit.  
18.Servicing-Do not attempt to service this unit yourself as opening  
or removing covers may expose you to dangerous voltage or  
other hazards. Refer all servicing to qualified service personnel.  
19.Damage Requiring Service-Unplug this unit from the wall  
outlet and refer servicing to qualified service personnel  
under the following conditions:  
20.Replacement Parts-When replacement parts are required, be  
sure the service technician has used replacement parts speci-  
fied by the manufacturer that have the same characteristics as  
the original part. Unauthorized substitutions may result in fire,  
electric shock, injury to persons or other hazards.  
21.Safety Check-Upon completion of any service or repairs to this  
unit, ask the service technician to perform routine safety checks  
to determine that the unit is in proper operating condition.  
22.Heat-This unit product should be situated away from heat  
sources such as radiators, heat registers, stoves, or other  
products (including amplifiers) that produce heat.  
a. When the power-supply cord or plug is damaged or frayed.  
IMPORTANT COPYRIGHT INFORMATION  
Unauthorized copying, broadcasting, public performance  
and lending of discs are prohibited.  
This product incorporates copyright protection technology that  
is protected by U.S. patents and other intellectual property  
rights. Use of this copyright protection technology must be  
authorized by Macrovision, and is intended for home and other  
limited viewing uses only unless otherwise authorized by  
Macrovision. Reverse engineering or disassembly is prohibited.  
LASER SAFETY  
This unit employs a laser. Only a qualified service person  
should remove the cover or attempt to service this device,  
due to possible eye injury.  
CAUTION: USE OF CONTROLS OR ADJUSTMENTS  
OR PERFORMANCE OF PROCEDURES OTHER THAN  
THOSE SPECIFIED HEREIN MAY RESULT IN HAZ-  
ARDOUS RADIATION EXPOSURE.  
CAUTION: VISIBLE AND INVISIBLE LASER RADIA-  
TION WHEN OPEN AND INTERLOCK DEFEATED.  
DO NOT STARE INTO BEAM.  
FCC WARNING- This equipment may generate or use  
radio frequency energy. Changes or modifications to this  
equipment may cause harmful interference unless the mod-  
ifications are expressly approved in the owner’s manual.  
The user could lose the authority to operate this equipment  
if an unauthorized change or modification is made.  
LOCATION: INSIDE, NEAR THE DECK MECHA-  
NISM.  
This Class B digital apparatus complies with Canadian  
ICES-003.  
Cet appareil numérique de la classe B est conforme à la  
norme NMB-003 du Canada.  
RADIO-TV INTERFERENCE  
This equipment has been tested and found to comply with  
the limits for a Class B digital device, pursuant to Part 15 of  
the FCC Rules. These limits are designed to provide reason-  
able protection against harmful interference in a residential  
installation. This equipment generates, uses, and can radiate  
radio frequency energy and, if not installed and used in  
accordance with the instructions, may cause harmful inter-  
ference to radio communications.  
However, there is no guarantee that interference will not  
occur in a particular installation. If this equipment does  
cause harmful interference to radio or television reception,  
which can be determined by turning the equipment off and  
on, the user is encouraged to try to correct the interference  
by one or more of the following measures:  
CAUTION: TO PREVENT ELECTRIC SHOCK,  
MATCH WIDE BLADE OF PLUG TO WIDE SLOT,  
FULLY INSERT.  
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES,  
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE  
DANS LA BORNE CORRESPONDANTE DE LA PRISE ET  
POUSSER JUSQU’AU FOND.  
A NOTE ABOUT RECYCLING  
This product’s packaging materials are recyclable and can  
be reused. Please dispose of any materials in accordance  
with your local recycling regulations.  
Batteries should never be thrown away or incinerated but  
disposed of in accordance with your local regulations con-  
cerning chemical wastes.  
1) Reorient or relocate the receiving antenna.  
2) Increase the separation between the equipment and receiver.  
3) Connect the equipment into an outlet on a circuit differ-  
ent from that to which the receiver is connected.  
4) Consult the dealer or an experienced radio/TV technician for help.  
The serial number of this product may be found on the back of the unit. No other unit has the same serial number as yours.  
You should record the number and other vital information here and retain this book as a permanent record of your purchase  
to aid identification in case of theft. Serial numbers are not kept on file.  
Date of Purchase  
Dealer Purchase from  
Dealer Address  
Dealer Phone No.  
Model No.  
Serial No.  
- 3 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SUPPLIED ACCESSORIES  
Remote Control Unit  
Batteries  
Owner’s Manual  
( 1EMN21903 )  
( NE240UD )  
2 AA Batteries  
If you need to replace these accessories, please refer to the PART NO. under the illustrations and call our  
help line mentioned on the front page.  
Depending on your antenna system, you may need different types of Combiners (Mixer) or Separators  
(Splitter). Contact your local electronics store for these items.  
LOCATION  
MOISTURE WARNING  
For safe operation and satisfactory performance of  
your unit, keep the following in mind when selecting  
a place for its installation:  
Moisture condensation may occur inside the unit when  
it is moved from a cold place to a warm place or after  
heating a cold room or under conditions of high humid-  
ity. If a DVD is played in a unit which has moisture, it  
may damage the DVD and the unit. Therefore when the  
condensation occurs inside the unit, turn the unit on  
and allow at least 2 hours for the unit to dry out.  
The stand of this TV is  
folded when you purchased.  
Place this TV face-down  
on a flat surface covered  
with the soft cloth.  
Do not bend from this side.  
Bend the stand slowly to  
forward until it clicks.  
SYMBOLS USED IN THIS MANUAL  
The following symbols below appear in some head-  
ings in this manual.  
If you want to fold the stand again,  
insert a thin rod into the hole in  
the right side of the stand as  
illustrated, bend the stand back-  
ward while you keep pushing the  
hole.  
: Description refers to playback of DVD video discs  
(in the DVD mode).  
Shield it from direct sunlight and  
keep it away from sources of intense heat.  
: Description refers to playback of Audio CDs  
(in the DVD mode).  
Avoid dusty or humid places.  
Avoid places with insufficient ventilation for  
proper heat dissipation. Do not block the ventilation  
holes at the top or bottom of the unit. Do not place  
the unit on a carpet because this will block the  
ventilation holes.  
: Description refers to playback of CD-RW/-R with  
MP3 files (in the DVD mode).  
Install unit in a horizontal position.  
QUICK  
Avoid locations subject to strong vibration.  
Do not place the unit near strong magnetic fields.  
Avoid moving the unit to locations where  
temperature differences are extreme.  
Be sure to remove a disc and unplug the AC power  
cord from the outlet before carrying the unit.  
: Description refers to the items to be set by the  
QUICK mode (in the DVD mode).  
TILT STAND  
You can adjust the stand to change the angle of the  
TV (-5° to 10°).  
TO AVOID THE HAZARDS OF  
ELECTRICAL SHOCK AND FIRE  
10˚  
-5˚  
Do not handle the power cord with wet hands.  
Do not pull on the power cord when disconnecting  
it from an AC wall outlet. Grasp it by the plug.  
If by accident, water is spilled on your unit, unplug  
the power cord immediately and take the unit to our  
Authorized Service Center for servicing.  
Do not put your fingers or objects into the unit disc slot  
Do not place anything directly on top of the unit.  
.
EN  
- 4 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2  
IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . . . . . . . .2  
SEARCH FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . .21  
TRACK SEARCH . . . . . . . . . . . . . . . . . . . . . . . . . . . .21  
TITLE / CHAPTER SEARCH . . . . . . . . . . . . . . . . . . .21  
TIME SEARCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22  
MARKER SET UP SCREEN . . . . . . . . . . . . . . . . . . .22  
SUPPLIED ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . .4  
LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4  
TO AVOID THE HAZARDS OF  
SPECIAL PLAYBACK FUNCTION . . . . . . . . . . . . . . . . .23  
REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23  
A-B REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23  
PROGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24  
RANDOM PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . .24  
ELECTRICAL SHOCK AND FIRE . . . . . . . . . . . . . . . .4  
MOISTURE WARNING . . . . . . . . . . . . . . . . . . . . . . . .4  
SYMBOLS USED IN THIS MANUAL . . . . . . . . . . . . . .4  
TILT STAND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4  
TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . .5  
FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6  
CHANGING THE SETTINGS . . . . . . . . . . . . . . . . . . . . .25  
SUBTITLE LANGUAGE . . . . . . . . . . . . . . . . . . . . . . .25  
AUDIO LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . . . .25  
STEREO SOUND MODE . . . . . . . . . . . . . . . . . . . . . .25  
CAMERA ANGLE . . . . . . . . . . . . . . . . . . . . . . . . . . .26  
BLACK LEVEL SETTING . . . . . . . . . . . . . . . . . . . . . .26  
VIRTUAL SURROUND . . . . . . . . . . . . . . . . . . . . . . . .26  
OPERATING CONTROLS AND FUNCTIONS . . . . . . . . . .7  
INSTALLING THE BATTERIES . . . . . . . . . . . . . . . . . .8  
PREPARATION FOR USE . . . . . . . . . . . . . . . . . . . . . . . .9  
ANTENNA/CABLE CONNECTION . . . . . . . . . . . . . . . .9  
EXTERNAL CONNECTION . . . . . . . . . . . . . . . . . . . . .10  
THE ON-SCREEN INFORMATION . . . . . . . . . . . . . . . . .27  
TV SECTION  
CHANGING THE DVD SET UP ITEMS . . . . . . . . . . . . . .28  
CUSTOM MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . .28  
D LANGUAGE SETTING . . . . . . . . . . . . . . . . . . . .28  
E DISPLAY SETTING . . . . . . . . . . . . . . . . . . . . . .28  
F AUDIO SETTINGS . . . . . . . . . . . . . . . . . . . . . . .29  
TV OPERATION AND SETTINGS . . . . . . . . . . . . . . . . .11  
INITIAL SET UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11  
WATCHING A TV PROGRAM . . . . . . . . . . . . . . . . . .11  
CHANNEL SET UP . . . . . . . . . . . . . . . . . . . . . . . . . .12  
PICTURE CONTROL . . . . . . . . . . . . . . . . . . . . . . . . .13  
BACK LIGHT SETTING . . . . . . . . . . . . . . . . . . . . . . .13  
SLEEP TIMER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13  
CLOSED CAPTION SYSTEM . . . . . . . . . . . . . . . . . .14  
MTS (Multi-Channel Television Sound) System . . . . . .14  
V-CHIP SET UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15  
G
H
PARENTAL CONTROL . . . . . . . . . . . . . . . . . . . .29  
OTHER SETTINGS . . . . . . . . . . . . . . . . . . . . . .30  
INITIALIZE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30  
LANGUAGE CODE LIST . . . . . . . . . . . . . . . . . . . . . .31  
CABLE CHANNEL DESIGNATIONS . . . . . . . . . . . . .31  
TROUBLESHOOTING GUIDE . . . . . . . . . . . . . . . . . . . .32  
A
B
C
TV RATING SET UP . . . . . . . . . . . . . . . . . . . . . .15  
MPAA RATING SET UP . . . . . . . . . . . . . . . . . . .16  
CHANGE ACCESS CODE . . . . . . . . . . . . . . . . .16  
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35  
DISC HANDLING . . . . . . . . . . . . . . . . . . . . . . . . . . . .35  
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35  
ESPAÑOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36  
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover  
MENU LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . . . .16  
DVD SECTION  
ABOUT THE DISCS . . . . . . . . . . . . . . . . . . . . . . . . . . . .17  
PLAYABLE DISCS . . . . . . . . . . . . . . . . . . . . . . . . . . .17  
UNPLAYABLE DISCS . . . . . . . . . . . . . . . . . . . . . . . .17  
PLAYING A DISC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18  
BASIC PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . .18  
DISC MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19  
TITLE MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19  
RESUME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19  
PAUSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19  
STEP BY STEP PLAYBACK . . . . . . . . . . . . . . . . . . .19  
FAST FORWARD / FAST REVERSE . . . . . . . . . . . . .20  
SLOW FORWARD / SLOW REVERSE . . . . . . . . . . . .20  
ZOOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20  
- 5 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FEATURES  
TV Mode  
MTS/SAP Tuner  
Infrared remote control  
Trilingual on screen TV setup display available in  
English, Spanish or French  
181 channel capability PLL frequency synthesizer  
tuner with direct station call (A converter may be  
necessary to view scrambled cable channels.)  
Auto power off system–If there is no air signal input  
from the antenna terminal and no operation for 15  
minutes, the unit will turn itself off automatically.  
Sleep timer–Allows you to have the unit automati-  
cally turn off at a desired time.  
V-CHIP–Enables parents to prevent their children  
from watching inappropriate material on TV.  
Closed Caption Decoder–You may view specially  
labeled (cc) TV programs, movies, news, etc. with  
either a dialogue caption or text display added to  
the program.  
DVD Mode  
Dolby Digital sound  
Parental lock  
You can set the control level to limit playback of  
discs which may not be suitable for children.  
This unit can handle Dolby Digital Multi-channel sur-  
round sound when connected to a Dolby Digital  
decoder.  
Automatic detection of discs  
This unit automatically detects if the loaded disc is  
DVD, Audio CD or  
Still/fast/slow/step playback  
Various playback modes are available including  
still pictures, fast forward/reverse, slow motion and  
step frames.  
.
CD-RW/-R with MP3 files  
On-screen display  
Information about the current operation can be dis-  
played on a TV screen, allowing you to confirm the  
currently active functions (such as program play-  
back), on the TV screen using the remote control.  
Random playback for Audio CD and MP3  
This unit can shuffle the order of tracks to play  
them in random order.  
Program playback for Audio CD and MP3  
You can program the order of tracks to play them  
in any desired order.  
Search  
Chapter search / Title search / Track search / Time  
search  
DVD menus in a desired language  
You can display DVD menus in a desired language,  
if available on a DVD.  
Repeat  
Chapter / Title / Track / Group / All / A-B  
Zoom  
Screen saver  
Allows you to enlarge video image.  
If the screen saver program is set to ON, it starts  
when there is no input from the unit for 5 minutes  
in stop mode.  
Marker  
The part designated by user can be called back.  
Resume Play  
User can resume to playback from the part at  
which the play was stopped.  
Subtitles in a desired language  
You can select a desired language for the display  
subtitles, if that language is available on a disc.  
Virtual Surround  
Bit rate indication  
Selecting a camera angle  
You can select the desired camera angle, if a disc  
contains sequences recorded from different angles.  
DRC (Dynamic range control)  
You can control the range of sound volume.  
Choices for audio language and sound mode  
You can select the desired audio language and  
sound mode, if different languages and modes are  
available on a disc.  
EN  
- 6 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATING CONTROLS AND FUNCTIONS  
NOTE  
O
When you select DVD mode, press [PLAY ] or [EJECT A] first or insert a disc into the disc slot.  
Otherwise, the DVD features are not operated.  
- REMOTE CONTROL  
9.SETUP button (P.12, P.28)  
Press to enter or exit the setup menu of TV/DVD.  
10. TITLE button (P.19)  
POWER PICTURE SELECT  
EJECT  
CH.  
Press to display the title menu.  
1
2
15  
16  
11. CLEAR button (P.21)  
1
4
2
5
8
0
3
6
Press to clear/cancel a setting currently entered.  
Press to clear “DISC INSIDE” display.  
17  
3
4
12. MODE button (P.24)  
7
SLEEP  
9
+100  
Press to call up the program/random screen in  
stop mode.  
VOL.  
18  
+10  
Press to call up the Black Level Setting/Virtual  
Surround screen during playback.  
SKIP  
ZOOM  
MUTE  
19  
20  
21  
5
6
13. SEARCH MODE button (P.21)  
Press to locate a desired point.  
PLAY  
STOP  
REV  
FWD  
14. AUDIO button  
22  
For TV mode (P.14): Press to select TV sound  
mode (STEREO/SAP/MONO).  
For DVD mode (P.25): Press to select a desired  
audio language (if available).  
DISC  
MENU  
PAUSE SLOW  
DISPLAY  
7
8
9
10  
11  
23  
24  
25  
ENTER  
SETUP  
TITLE  
RETURN  
15. EJECT A button (P.18)  
26  
27  
Press to remove a disc from the unit.  
CLEAR SEARCH MODE REPEAT  
A-B  
16. SELECT button (P.11)  
AUDIO SUBTITLE ANGLE  
MODE  
Press to select the TV mode, external input mode  
or DVD mode.  
12  
13  
14  
28  
29  
30  
K
L
17. CH.  
/
buttons (P.11)  
Press to select memorized channels.  
X
Y
18. VOL.  
/
buttons (P.11)  
[Fig. 1]  
Press to control the volume level for the DVD and  
1.POWER button (P.11, P.18)  
Press to turn the power on and off.  
2.PICTURE button (P.13)  
Press to adjust the picture.  
TV.  
19. MUTE button (P.11)  
Press to mute the sound or press it again to  
restore sound.  
3.Number buttons (P.11, P.21)  
20. ZOOM button (P.20)  
Press to select a desired channel number directly.  
+100 button (For TV mode)  
Press to enlarge the part of a DVD-reproduced  
image.  
Press to select channels higher than 99.  
+10 button (For DVD mode)  
E
21. REV  
button (P.20)  
Press to view the DVD picture in fast/slow  
reverse motion.  
Press to enter desired numbers higher than 9.  
4.SLEEP button (P.13)  
D
FWD  
button (P.20)  
Press to set the Sleep Timer.  
5.SKIP H / G buttons (P.21)  
Press once to skip chapters/tracks to a desired point.  
6.PLAY O button (P.18)  
Press to playback the disc.  
7.PAUSE F button (P.19)  
Press to pause the current disc operation.  
Press to view in fast/slow forward motion.  
22. STOP C button (P.18)  
Press to stop operation of the disc.  
23. DISC MENU button (P.19)  
Calls up the DVD menu.  
24. ENTER button (P.12, P.19)  
Press to accept a setting.  
8.DISPLAY button  
For TV mode (P.14)  
25.  
K
(Up) /  
(P.12, P.19)  
L
(Down) / { (Left) / B (Right) buttons  
:
Press to display the current channel number on  
Press to select or adjust menu items.  
the TV screen.  
For DVD mode (P.27)  
:
P
ress to display the current status on the TV screen.  
- 7 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
26. RETURN button (P.22)  
29. REPEAT button (P.23)  
Press to return to the previous screen in the setup  
menu.  
Repeats playback of the current disc, title,  
chapter, group or track.  
27. A-B button (P.23)  
30. SUBTITLE button (P.25)  
Press to repeat the playback of a selected section.  
Press to select a desired subtitle language.  
28. ANGLE button (P.26)  
Press to change the camera angle to see the  
sequence being played back from a different angle  
(if available).  
- CONTROL PANEL  
31. MENU button  
31 323334 35 36 37 38  
Press to enter or exit the setup menu of TV/DVD.  
32. STOP C button (P.18)  
Press to stop operation of the disc.  
33. PLAY B button (P.18)  
DVD  
Press to playback of the disc.  
A
34. EJECT button (P.18)  
Press to remove a disc from the unit.  
Y
X
35. VOLUME  
/
buttons (P.11)  
Press to control the volume level for the DVD and  
TV.  
L
K
36. CHANNEL  
/
buttons (P.11)  
Press to select memorized channels.  
37. SELECT button (P.11)  
Press to select to TV mode, external input mode  
or DVD mode.  
38. POWER button (P.11, P.18)  
Press to turn the power on and off.  
39. Remote sensor window  
[Fig. 2]  
39  
INSTALLING THE BATTERIES  
BATTERY PRECAUTIONS  
1 Open the battery compartment cover by  
pressing the cover on the remote control unit  
in the direction of the arrow.  
Be sure to follow the correct polarity as indicated  
in the battery compartment. Reversed batteries  
may cause damage to the device.  
2 Insert 2 “AA” penlight batteries into the bat-  
tery compartment in the direction indicated by  
the polarity (+/-) markings.  
Do not mix different types of batteries together  
(e.g. Alkaline and Carbon-Zinc) or old batteries  
with fresh ones.  
If the device is not to be used for a long period of  
time, remove the batteries to prevent damage or  
injury from possible battery leakage.  
3 Replace the cover.  
Do not try to recharge batteries not intended to be  
recharged; they can overheat and rupture.  
NOTE  
We do not recommend the use of universal remote controls. Not all of the functions may be controlled  
with a universal remote control.  
If you decide to use a universal remote control with this unit, please be aware that the code number given  
may not operate this unit. In this case, please call the manufacturer of the universal remote control.  
EN  
- 8 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREPARATION FOR USE  
ANTENNA/CABLE CONNECTION  
NOTE  
Cables used here are commercially available.  
For your safety and to avoid damages to the unit, unplug the antenna cable from the ANT jack  
before moving the unit.  
- ANTENNA/CABLE CONNECTION  
IF YOU HAVE A JACK ON THE WALL  
Connect the TV to the wall-mounted antenna jack  
with an RF cable (commercially available).  
[Rear of this unit]  
IF YOU HAVE A WIRED CABLE  
DIGITAL  
AUDIO OUT  
(COAXIAL)  
Connect the TV to the wired antenna cable.  
2
O
E
R
L
D
I
V
O
P
I
D
U
A
T
N
E
r
N
Y
NOTE  
O
M
P
C
b
P
Before plugging the antenna into the ANT jack of the  
P
R
L
unit, check that the pin is not bent. If it is bent,  
straighten the pin as illustrated, then plug the pin into  
the ANT jack of the unit.  
O
I
D
U
A
1
O
E
O
E
ID  
V
D
I
V
O
E
D
I
V
-
S
T
N
A
E
N
O
H
P
D
A
E
H
Bent pin  
from Cable TV signal  
or Antenna  
Cable  
Plug  
RF Cable  
(Needs to be  
straightened)  
(Straight pin)  
ANT  
- CABLE/SATELLITE BOX CONNECTION  
WHEN USING CABLE BOX/SATELLITE  
BOX  
[Rear of this unit]  
If your cable service supplies you with a converter  
box or if you use a satellite system, you can use the  
basic connection shown above.  
L
O
A
O
X
T
U
L
T
I
G
I
)
D
A
(
I
D
A
I
U
A
O
C
Channel selection must be made with the converter  
box or satellite box. This means that channels cannot  
be changed using the remote control of this unit.  
2
O
E
R
L
D
I
Cable Box  
or Satellite Box  
V
O
I
D
U
A
T
N
E
N
Y
O
P
M
P
C
Pb  
Pr  
R
L
O
I
D
U
A
1
O
OUT  
IN  
E
O
D
I
E
V
D
I
V
S-VIDEO  
T
N
A
E
N
O
H
P
D
A
E
H
75-ohm  
Coaxial Cable  
T
N
A
from Cable Company  
or Satellite dish  
NOTE  
Note to CATV system installer:  
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides  
guidelines for proper grounding and in particular, specifies that the cable ground shall be connected to the grounding  
system of the building as close to the point of cable entry as practical.  
- 9 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EXTERNAL CONNECTION  
You can connect this unit to your own Audio/Video  
equipment.  
Be sure to turn off the power to all components in  
the system before connecting another component.  
L
O
T
U
Refer to the Owner’s Manuals for the equipment  
to be connected to the unit.  
ITA  
IO  
IG  
AUDIO  
D
A
D
U
XIAL)  
A
O
(C  
2
O
E
D
R
L
I
V
O
P
I
D
U
A
T
N
E
r
N
Y
O
M
P
C
b
VIDEO2  
VIDEO1  
P
NOTE  
P
R
L
O
I
D
When you use the external input, select “VIDEO1” or  
“VIDEO2” by pressing [SELECT]. (Refer to page 11.)  
U
A
1
O
E
O
E
ID  
V
D
I
V
S-VIDEO  
T
N
A
E
N
O
H
P
D
A
E
H
To use the VIDEO1 input jacks, select “VIDEO1”.  
To use the VIDEO2 input jacks, select “VIDEO2”.  
- VIDEO1 INPUT  
Use this connection if your own A/V equipment (e.g.  
VCR) has Video output and Audio out jacks. When  
using S-Video cable, better picture is available.  
ex.  
Audio Cable  
(OUT)  
(OUT)  
R
IO  
L
D
U
A
Video Cable  
OR  
1
O
E
ID  
V
O
E
E
ID  
V
Video Cassette  
Recorder  
O
ID  
-V  
S
S-Video Cable (OUT)  
NOTE  
If your own equipment is monaural (has only one Audio jack), connect the Audio cable to AUDIO L jack of this unit.  
If you connect Video jack and S-VIDEO jack simultaneously, the S-VIDEO jack is given priority over the VIDEO jack.  
- VIDEO2 INPUT  
Use this connection if your own A/V equipment (e.g.  
video camera, video game) has Component Video  
output (Y, Pb, Pr) jacks. You can enjoy the best pic-  
ture with this connection.  
ex.  
2
O
E
A
ID  
V
(OUT)  
(OUT)  
Audio Cable  
R
IO  
L
D
U
Video Camera  
COMPONENT  
Y
Component  
Video Cable  
Pb  
Pr  
Video Game  
- AUDIO OUTPUT  
You can enjoy DVD sound with more  
presence by connecting digital audio  
equipment such as Dolby Digital decoder.  
To coaxial digital  
audio input jack  
Home Audio System  
L
O
IA  
A
IO  
X
IT  
D
A
IG  
U
D
A
T
)
U
L
O
(C  
Dolby Digital decoder  
NOTE  
The audio source on a disc in a Dolby Digital Multi-channel surround format cannot be recorded as digital sound by an MD or DAT deck.  
If connected to a Dolby Digital decoder, set “DOLBY DIGITALto “BITSTREAM” for audio output in the setup mode. (Refer to page 29.)  
Unless connected to a Dolby Digital decoder, set “DOLBY DIGITALto “PCM” for audio output in the setup mode. Playing  
a unit using incorrect settings may generate noise distortion and may also damage the speakers. (Refer to page 29.)  
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol  
are trademarks of Dolby Laboratories.  
EN  
- 10 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TV SECTION  
TV OPERATION AND SETTINGS  
INITIAL SET UP  
WATCHING A TV PROGRAM  
When you turn on the power for the first time,  
the SELECT LANGUAGE screen is displayed.  
Select the language for screen display and perform  
auto programming of the channels.  
1 Press[POWER] to turn on the unit.  
TV  
TV  
POWER  
NOTE  
-
HELPFUL HINTS  
-
If the TV screen shows snow  
noise and there is no operation  
for more than 5 seconds,  
1. PLEASE CHECK TO SEE IF THE  
ANTENNA/CABLE/SATELLITE IS  
PROPERLY CONNECTED.  
1 After antenna or cable connection is  
completed, connect the power cord  
into a standard AC outlet.  
2. DID YOU PERFORM “AUTO PRESET CH”  
?
3. PLEASE REFER TO FRONT PAGE OF THE  
OWNER’S MANUAL OR REAR PANEL FOR  
SUPPORT LINE INFORMATION.  
“HELPFUL HINTS” appears.  
NOTE  
Follow the instructions listed on-screen.  
If those settings do not work properly, please call our  
help line on the front page of this owner's manual.  
• If any digits are displayed in the corner of the  
screen, press [POWER] without unplugging  
the power cord.  
2 Press [CH. K / L] or the Number buttons to  
select the desired channel number.  
2 Press [POWER] to turn on the unit.  
1
4
7
2
5
8
3
6
POWER  
CH.  
OR  
9
+100  
SELECT LANGUAGE  
3 Press one of the keys listed  
0
+10  
K
L
X
ENGLISH  
ESPAÑOL  
FRANÇAIS  
NEXT:PRESS CH  
DESPUÉS:PRESIONE CH  
APRÈS:PRESSEZ VOL  
below to select the desired  
language of on-screen menu.  
NOTE  
K
For channel number selection with number buttons:  
ENGLISH: [CH.  
ESPAÑOL: [CH.  
FRANÇAIS: [VOL.  
]
]
L
To select single-digit channel number, press  
[0] first. (e.g. Press [0] [2] for channel 2.)  
X
]
To select cable channels which are higher  
4 Confirm the antenna (or cable)  
INITIAL SETUP  
than 99, press [+100/+10] first.  
PLEASE CONNECT ANTENNA OR CABLE  
OR SATELLITE TO THIS UNIT.  
THEN PRESS CH  
IN ORDER TO PERFORM  
“AUTO PRESET CH ”.  
K
connection and press [CH. ].  
(e.g. Press [+100/+10] [2] [5] for channel 125.)  
K
,
The tuner scans and memorizes  
3 Press [VOL. X / Y] to select the desired vol-  
all active channels in your area.  
ume level.  
5When the scanning is  
completed, the tuner stops  
on the lowest memorized  
channel.  
CH 15  
VOL.  
VOLUME 20  
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
(Example)  
Press [MUTE] to instantly mute the sound.  
Press it again to restore the previous volume level.  
NOTE  
If [MENU] is pressed during channel scanning,  
the tuner stops scanning and the lowest memo-  
rized channel is displayed.  
The INITIAL SETUP menu is displayed  
every time you turn on the unit unless the  
scanning is completed.  
NOTE  
If you press [CH. K / L] in the DVD mode,  
you can change the TV channels. Even if you  
turn off the unit in the DVD mode, when you  
turn it on again, it will go into the TV mode.  
TO WATCH CABLE OR SATELLITE  
CHANNEL  
If the unit is connected to a cable box or satellite  
box, press [CH. K / L] to select CH3 or CH4  
according to the output channel setting of the device  
and select desired channel on that device.  
In case no channel can be  
received by the channel scan-  
NO TV SIGNALS  
ning, “NO TV SIGNALS” is  
displayed on the screen. Turn  
off the unit and check the  
antenna connection, then  
follow steps 1 to 5 again.  
TO WATCH EXTERNAL INPUT  
You can change the setting after completing  
INITIAL SET UP by LANGUAGE menu or  
CHANNEL SET UP menu. (Refer to  
“MENU LANGUAGE” on page 16 or  
“CHANNEL SET UP” on page 12).  
When an external equipment is connected to  
AUDIO/VIDEO input jacks on the right side, press  
[SELECT] or [CH. K / L] repeatedly until  
“VIDEO1” or “VIDEO2” appears on the screen.  
- 11 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ADDING/DELETING CHANNELS  
The channels you no longer receive or seldom watch  
can be deleted from the memory. (Of course, you can  
add the deleted channel into the memory again.)  
CHANNEL SET UP  
AUTO CHANNEL PROGRAMMING  
As the initial setting, this unit has memorized all  
channels, including the ones not available in your  
area. This feature automatically puts only available  
channels into the memory.  
1 Press [SETUP] then press [K] or [L] to point  
to “CHANNEL SET UP”.  
- TV SET UP -  
1 Press [SETUP] then press [K] or [L] to point  
B
CHANNEL SET UP  
V-CHIP SET UP  
SETUP  
LANGUAGE [ENGLISH]  
to “CHANNEL SET UP”.  
CAPTION  
[OFF]  
BACK LIGHT [BRIGHT]  
- TV SET UP -  
B
CHANNEL SET UP  
V-CHIP SET UP  
SETUP  
LANGUAGE [ENGLISH]  
CAPTION  
[OFF]  
2 Press [ENTER] then press [K] or [L] to point  
BACK LIGHT [BRIGHT]  
to “ADD/DELETE CH”.  
– CHANNEL SET UP –  
2 Press [ENTER] then press [K] or [L] to point  
B
ADD / DELETE CH (CATV)  
AUTO PRESET CH  
ENTER  
to “AUTO PRESET CH”.  
– CHANNEL SET UP –  
ADD / DELETE CH (CATV)  
B
AUTO PRESET CH  
ENTER  
3 Press [ENTER] then press the Number but-  
L] to select the desired  
K
/
tons or [CH.  
channel number.  
3 Press [ENTER].  
15  
1
2
5
8
3
6
ENTER  
4
7
ENTER  
9
The tuner scans and memorizes all the active  
channels in your area.  
The tuner stops on the lowest memorized channel.  
+100  
0
+10  
ADD/DELETE  
4 Press [ENTER] then the channel number  
turned to red. The channel is deleted from  
memory. If the channel number turned to  
blue, the channel is added into memory.  
NOTE  
When “AUTO PRESET CH” is activated  
where there is no TV signal input, “NO TV  
SIGNALwill appear on the display after the  
completion of channel scanning.  
ENTER  
The unit may recognize CATV channels to be  
TV channels if reception condition is poor. In  
this case, check the antenna connection and  
try “AUTO PRESET CH” again when recep-  
tion conditions are better.  
Auto channel programming is NOT neces-  
sary when connected to a cable box or  
satellite box. Just select the channel for  
cable box or satellite input (ex. CH3 or  
CH4) on the unit, then select your desired  
channel on the cable box or satellite box.  
To delete another channel, repeat steps 3 to 4.  
If you press [ENTER] again, the channel is  
memorized again.  
Added channel : Light blue  
Deleted channel : Light red  
5 Press [SETUP] to exit the menu.  
SETUP  
NOTE  
To confirm that channel(s) has(have) been  
deleted or added, press [CH. K / L].  
EN  
- 12 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
POWER PICTURE SELECT  
EJECT  
BACK LIGHT SETTING  
1 Press [SETUP] then press [K] or [L] to point  
3
SLEEP  
0
to “BACK LIGHT”.  
+10  
- TV SET UP -  
SKIP  
ZOOM  
MUTE  
CHANNEL SET UP  
V-CHIP SET UP  
SETUP  
LANGUAGE [ENGLISH]  
CAPTION  
[OFF]  
B
BACK LIGHT [BRIGHT]  
PLAY  
STOP  
REV  
FWD  
2 Press [ENTER] then press [s] or [B] to  
DISC  
MENU  
PAUSE SLOW  
DISPLAY  
select to “BRIGHT”, “NORMALor “DARK”.  
ENTER  
ENTER  
SETUP  
TITLE  
RETURN  
CLEAR SEARCH MODE REPEAT  
A-B  
3Press [SETUP].  
AUDIO SUBTITLE ANGLE  
MODE  
SETUP  
Shaded buttons are used for following operation.  
PICTURE CONTROL  
SLEEP TIMER  
The Sleep Timer function turns off the unit without  
using [POWER] after a desired period of time.  
The unit’s picture controls, brightness, contrast,  
color, tint and sharpness, are preset to factory specifi-  
cations. Although they are usually the best, you may  
need to make some further adjustments for a more  
natural looking image.  
1 Press [SLEEP].  
1
Press [PICTURE] then press [K] or [L] to select  
the desired control “BRIGHTNESS”, “CONTRAST”,  
“COLOR”, “TINT” or “SHARPNESS”.  
SLEEP  
SLEEP 0 MINUTE  
PICTURE  
2 Press [SLEEP] repeatedly until the desired  
BRIGHTNESS  
sleep time is displayed.  
-
+
SLEEP  
2 Press  
[s] or [B] to adjust to your desired  
level within 5 seconds.  
Each press increases the time by 10 minutes up  
to 90 minutes.  
After 5 seconds, the Sleep Timer setting will  
disappear automatically.  
If you select “SLEEP 0 MINUTE”, Sleep Timer  
setting is canceled.  
BRIGHTNESS  
CONTRAST  
COLOR  
to decrease  
to increase  
brightness  
to increase  
contrast  
brightness  
to decrease  
contrast  
to pale  
to brilliant  
TINT  
SHARPNESS  
to purple  
to soft  
to green  
to clear  
Even if there is a power failure of any kind, the  
unit will retain its memory for this feature.  
NOTE  
The picture control display will disappear automati-  
cally after 10 seconds unless you press any buttons.  
- 13 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTE  
CLOSED CAPTION SYSTEM  
You can view specially labeled (cc) TV programs,  
movies, news and pre-recorded tapes with either a  
dialogue caption or text display.  
Even if there is a power failure of any  
kind, the unit will retain its memory for  
this feature.  
CAPTION mode: You can watch dramas, movies and  
news while captioning the dialogues and the contents  
of news.  
TEXT mode: You can watch half screen text informa-  
tion if you want.  
1-2: You may get these captions or text information  
by selecting either “1” or “2”. “2” is usually used for  
a second language if available.  
MTS (Multi-Channel Television  
Sound) System  
TO SELECT TV SOUND MODE  
1 Press [AUDIO] repeatedly to select the MTS  
output mode.  
NOTE  
Not all programs are broadcast with closed cap-  
AUDIO  
tions. Your unit is designed to provide error-free  
closed captions from high quality antenna, cable  
and VCR signals. Conversely, poor quality sig-  
nals are likely to result in caption errors or no  
captions at all. Common signal conditions which  
may cause caption errors are listed below:  
STEREO  
The output mode changes as described below  
every time you press [AUDIO].  
STEREO  
SAP*  
MONO  
Automobile ignition noise  
Electric motor brush noise  
Weak snowy reception on TV screen  
Multiplex signal reception displaying picture  
ghosts or airplane flutter  
* Second Audio Program (SAP):  
Sometimes broadcasters add another channel of  
audio to the programs they air. This is usually a  
secondary language or perhaps a radio station.  
After 5 seconds, the current audio status will  
disappear from the TV screen.  
If the unit displays a black box on the TV  
screen, this means that the unit is set to the  
TEXT mode. To clear screen, select  
“CAPTION1”, “CAPTION2” or “OFF”.  
NOTE  
The initial setting is “STEREO”.  
This setting is saved even if the unit is turned  
off or the AC cord is unplugged.  
TO CHECK THE SOUND STATUS  
By pressing [DISPLAY], the status shown below  
will appear on the display when you receive a broad-  
cast on the unit tuner channel you are watching.  
1 Press [SETUP] then press [K] or [L] to point  
to “CAPTION”.  
- TV SET UP -  
CH 123  
STEREO/SAP  
CHANNEL SET UP  
SETUP  
V-CHIP SET UP  
3)  
2)  
1)  
LANGUAGE [ENGLISH]  
B
CAPTION  
[OFF]  
BACK LIGHT [BRIGHT]  
2 Press [ENTER] repeatedly to select the  
desired caption menu “CAPTION1”,  
“CAPTION2”, “TEXT1” or “TEXT2”.  
- TV SET UP -  
1) When a program is broadcast in stereo,  
“STEREO” appears on the TV screen.  
CHANNEL SET UP  
V-CHIP SET UP  
2) When a program is broadcast in second audio,  
LANGUAGE [ENGLISH]  
ENTER  
[CAPTION1]  
B
CAPTION  
“SAP” appears on the TV screen.  
BACK LIGHT [BRIGHT]  
3) When a program broadcast both in stereo and sec-  
ond audio, “STEREO/SAP” appears on the TV  
screen.  
If you select “OFF”, Closed Caption System set-  
ting is canceled.  
3 Press [SETUP] to exit the menu.  
SETUP  
EN  
- 14 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TV RATING SET UP  
1
4
2
5
8
0
3
6
A
CH.  
Follow steps to in the V-CHIP SET UP.  
1
3
7
SLEEP  
9
+100  
4 Press [K] or [L] to select the desired TV rat-  
ing to be blocked then press [ENTER] repeat-  
edly to set “BLOCK” or “VIEW”.  
VOL.  
+10  
ZOOM  
SKIP  
MUTE  
B
TV–Y  
TV–Y7  
TV–G  
TV–PG (  
TV–14  
TV–MA(  
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
(
)
PLAY  
STOP  
ENTER  
)
)
)
REV  
FWD  
(
DISC  
MENU  
PAUSE SLOW  
DISPLAY  
Selection  
TV-Y  
TV-Y7  
TV-G  
TV-PG  
TV-14  
Rating Category Explanations  
Appropriate for all children  
Appropriate for children seven and older  
General Audience  
Parental Guidance suggested.  
Unsuitable for children under 14  
ENTER  
SETUP  
TITLE  
RETURN  
Shaded buttons are used for following operation.  
TV-MA Mature audience only  
V-CHIP SET UP  
NOTE  
V-CHIP SET UP  
This feature enables parents to prevent their children  
from watching inappropriate material on TV. When  
you try to access a program which is blocked, “PRO-  
TECTED PROGRAM by ...message appears on  
the TV screen.  
When you select a rating and set it to  
“BLOCK”, the higher ratings will be blocked  
automatically. The lower ratings will be avail-  
able for viewing.  
TV–Y  
TV–Y7  
TV–G  
TV–PG (DLSV )  
TV–14 (DLSV)  
TV–MA ( LSV)  
[VIEW]  
(
)
[VIEW]  
1 Press [SETUP] then press [K] or [L] to point  
B
[BLOCK]  
[BLOCK]  
[BLOCK]  
[BLOCK]  
to “V-CHIP SET UP”.  
- TV SET UP -  
CHANNEL SET UP  
V-CHIP SET UP  
B
SETUP  
When you set the lowest rating to “VIEW”, all  
other ratings will automatically be available  
for viewing.  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
BACK LIGHT [BRIGHT]  
2 Press [ENTER] then press the Number  
5 When you select the ratings of TV-Y7, TV-PG,  
TV-14 or TV-MA you will have the option of  
setting sub rating categories.  
Buttons to enter the access code.  
1
4
7
2
5
8
3
6
9
ACCESS CODE  
Press [K] or [L] to select a rating with sub-  
ratings you wish to block, then press  
[ENTER] twice.  
_
_
_
_
ENTER  
0
Press [K] or [L] to select a sub-rating, then  
press [ENTER] to set it to “BLOCK” or “VIEW”.  
For the first time set-up or in the event the unit  
has lost power, enter the default code of 0000.  
Selection  
TV-Y7  
FV  
Rating Category Explanations  
3 Press [K] or [L] to select “TV RATING”,  
MPAA RATING” or “CHANGE CODE” then  
Fantasy Violence  
press [ENTER].  
TV-PG, TV-14, TV-MA  
– V-CHIP SET UP –  
D
L
S
Suggestive Dialog (TV-PG, TV-14 only)  
B TV RATING  
MPAA RATING  
Coarse Language  
Sexual Situation  
Violence  
CHANGE CODE  
ENTER  
V
A
B
C
NOTE  
TV RATING:  
MPAA RATING: See  
CHANGE CODE: See  
See  
TV RATING SET UP  
MPAA RATING SET UP  
CHANGE ACCESS CODE  
The blocked sub-ratings will appear next to  
the rating category in the “TV RATING”  
menu.  
- 15 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Make sure you enter exactly the same new code  
in the “CONFIRM CODE” space as one in the  
“NEW CODE” space. If they are different, the  
“NEW CODE” space is cleared for redoing.  
6 Press [SETUP] to exit the menu.  
SETUP  
NOTE  
5 Press [SETUP] to exit the menu.  
To change the rating, the TV must be turned  
SETUP  
to an unprotected program. If “PROTECTED  
PROGRAM by ...appears on the screen,  
please change the channel to a station that is  
not protected.  
NOTE  
Your personal access code will be erased and  
will return to the default (0000) when a power  
failure occurs or when you turn off the power  
using a wall switch. If you have forgotten the  
code, unplug the power cord for 10 seconds  
to restore the access code to 0000.  
B MPAA RATING SET UP  
Follow steps to in the V-CHIP SET UP on page  
1
3
15.  
4 Press [K] or [L] to point to your desired item,  
then press [ENTER] to select “BLOCK” or  
“VIEW”.  
MENU LANGUAGE  
1 Press [SETUP] then press [K] or [L] to point  
G
[VIEW]  
to “LANGUAGE”.  
PG  
[VIEW]  
PG–13  
R
NC–17  
X
[VIEW]  
ENTER  
- TV SET UP -  
B
[BLOCK]  
[BLOCK]  
[BLOCK]  
CHANNEL SET UP  
V-CHIP SET UP  
SETUP  
B
LANGUAGE [ENGLISH]  
CAPTION  
[OFF]  
BACK LIGHT [BRIGHT]  
Selection  
G
Rating Category Explanations  
General Audience  
PG  
PG-13  
R
Parental Guidance suggested  
Unsuitable for children under 13  
Restricted; under 17 requires accompa-  
nying parent or adult guardian  
No one under 17 admitted  
2 Press [ENTER] repeatedly to select  
“ENGLISH”, “ESPAÑOL= Spanish or  
“FRANÇAIS”= French.  
ENTER  
NC-17  
X
Mature audience only  
3 Press [SETUP] to exit the menu.  
When you select a rating and set it to “BLOCK”,  
the higher ratings will be blocked automatically.  
The lower ratings will be available for viewing.  
When you set the lowest rating to “VIEW”, all other  
ratings will automatically be available for viewing.  
SETUP  
NOTE  
This function effects only the language on the  
screen menu and not the audio source.  
5 Press [SETUP] to exit the menu.  
If for some reason the menu is in Spanish or  
SETUP  
French, press [SETUP], press [K] or [L] to  
point to “IDIOMA [ESPAÑOL]” or  
“LANGAGE [FRANÇAIS]”, then press  
[ENTER] repeatedly to select desired  
language, then press [SETUP].  
CHANGE ACCESS CODE  
C
Follow steps to in the V-CHIP SET UP on page  
1
3
15.  
4 Press the Number buttons to enter your  
desired access code in the “NEW CODE”  
space, then enter the same code in the  
“CONFIRM CODE” space. When completed,  
the menu will return to “V-CHIP SET UP”.  
NEW CODE  
1
4
7
2
5
8
3
6
9
X X X X  
CONFIRM CODE  
_
_
_
_
0
EN  
- 16 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DVD SECTION  
ABOUT THE DISCS  
PLAYABLE DISCS  
Recorded  
signals  
Playable  
discs  
Disc size  
Disc type  
Region code  
Mark (logo)  
DVD-Video  
* 1,2,4,6,10,11  
or  
DVD-RW  
DVD-R  
* 1,3,4,5,  
6,7,9,10  
Example  
Title 1  
Title 2  
Digital video 5 inches  
Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1 Chapter 2  
(MPEG2)  
(12cm)  
DVD+RW  
DVD+R  
* 1,3,4,5,  
6,8,9,10  
Audio CD  
* 4,6,10  
Digital audio  
Audio CD  
MP3  
Example  
Track 1 Track 2 Track 3 Track 4 Track 5 Track 6  
5 inches  
(12cm)  
Example  
Digital audio  
CD-RW  
CD-R  
* 4,5,6,9,10  
Group 1  
Group 2  
or  
MP3  
Track 1 Track 2 Track 3 Track 4 Track 5 Track 6  
is a trademark of DVD Format/Logo Licensing Corporation.  
If you cannot play back a disc which bears one of the marks above, check the following notes.  
*1: This unit conforms to the NTSC color system. Discs recorded in other color systems such as PAL cannot be played back.  
*2: Certain DVD-Video discs do not operate as described in this manual due to the intentions of the disc’s producers.  
*3: Discs recorded in the VR (Video Recording) format cannot be played back.  
*4: Scratched or stained discs may not be played back.  
*5: Some discs cannot be played back because of incompatible recording conditions, characteristics of the  
recorder or special properties of discs.  
*6: You can play back discs which bear the marks above. If you use nonstandardized discs, this unit may not  
play them back. Even if they are played back, the sound or video quality will be compromised.  
*7: You may play back the unfinalized DVD-R/RW disc recorded in the video format on our brand’s DVD recorder. However, depend-  
ing on the recording status of a disc, the disc may not be played back at all or normally (the picture or sound may not be smooth,  
etc.). In this case, you need to finalize the disc with the DVD recorder. Refer to the manual accompanying the DVD recorder.  
*8: Only the discs recorded in the video format and finalized can be played back.  
Unfinalized discs cannot be played back. Depending on the recording status of a disc, the disc may not be  
played back at all or normally (the picture or sound may not be smooth, etc.).  
3
*9: If there is too much recording space left on a disc (the used portion is less than 2- / " (55mm) across), it may not play back properly.  
16  
*10: Do not glue paper or put stickers on to the disc. These may damage the disc and the unit may not read it correctly.  
*11: The number inside the symbol refers to a region of the world and a disc encoded in a specific region for-  
mat can only be played back on unit with the same region code.  
UNPLAYABLE DISCS  
NEVER play back the following discs. Otherwise, the unit may result in malfunction.  
DVD-RAM / CD-i / Photo CD / Video CD / DVD with region codes other than 1 or ALL /  
DTS-CD / DVD-ROM for personal computers / CD-ROM for personal computers  
Never insert a disc which is broken or whose form is abnormal (other than 5 inch (12cm) round disc).  
On the following disc, the sound MAY NOT be heard.  
Super Audio CD  
NOTE  
Only the sound recorded on the normal CD layer can be delivered.  
The sound recorded on the high density Super Audio CD layer cannot be delivered.  
Any other discs without compatibility indications  
EN  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PLAYING A DISC  
POWER PICTURE SELECT  
EJECT  
NOTE  
When the DVD mode has been switched to the  
TV mode, the DVD mode shuts down first and  
then the TV picture and sound appears in about  
4 seconds. Similarly, when [POWER] is  
pressed to turn off in the DVD mode, this mode  
shuts down first and then the unit is turned off.  
3
SKIP  
ZOOM  
MUTE  
may appear at the top-right on the TV  
PLAY  
STOP  
REV  
FWD  
screen during operation, warning that a pro-  
hibited operation has been encountered by the  
DVD or the disc.  
With DVDs that use titles for playback pro-  
gram signals, playback may start from the  
second title or it may skip these titles.  
During the playback of a two layered disc,  
pictures may stop for a moment. This happens  
when the 1st layer switches to the 2nd layer.  
This is not a malfunction.  
DISC  
MENU  
PAUSE SLOW  
DISPLAY  
ENTER  
SETUP  
TITLE  
RETURN  
Shaded buttons are used for following operation.  
If the disc doesn’t come out at step 5, press  
and hold [EJECT A] on the unit to remove  
the disc from the unit.  
BASIC PLAYBACK  
GETTING STARTED  
MP3 PLAYBACK  
Turn on the power of amplifier and any other compo-  
nents, if necessary.  
1 In stop mode, press [DISC MENU], then press  
[K] or [L] to select the desired group or track.  
1 Press [POWER] then the power will turn on.  
POWER  
DISC  
folder name 1  
folder name 2  
MENU  
2 Open the disc door manually.  
folder name 3  
folder name 4  
file name 1  
file name 2  
file name 3  
folder name 1  
If a group is selected, press [B] or [ENTER] to go  
on to the track selection screen. Press [s] to go  
back to previous screen.(except for the top page.)  
3 Insert a disc with the label facing back of the  
unit to start playing it. By simply placing the  
disc gently into the slot, it will be loaded auto-  
matically, then close the disc door manually.  
If a track is selected, press [ENTER] to start  
playing tracks. Starting from the one you’ve just  
chosen the subsequent tracks will be played.  
If the entire file list cannot be displayed at once  
on a screen, “n” appears to go to the next page.  
Press [TITLE] to return to the top file of the  
highest hierarchy in the program and file list.  
2 Press [STOP C] to stop playback.  
STOP  
Playback will start from the first chapter/track of the disc.  
If the playback does not start automatically,  
press [PLAY O].  
When you playback a DVD which features a  
NOTE  
Folders are known as Groups; files are known as Tracks.  
3
MP3 files are accompanied by  
icon.  
title menu, it may appear on the screen. In this  
Maximum of 255 folders can be recognized.  
Maximum of 999 files can be recognized.  
Up to 8 hierarchies can be created.  
case, refer to “TITLE MENU” on page 19.  
4 Press [STOP C] to stop playback.  
This unit recommends the use of files recorded  
at the below specifications:  
STOP  
Sampling frequency: 44.1kHz or 48kHz  
5
Press [EJECT A] to remove the disc from the unit.  
Constant bit rate: 32kbps ~ 320kbps  
EJECT  
For MP3 file recorded in Variable Bit Rate (VBR),  
the unit may not display the actual elapsed time.  
EN  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DISC MENU  
RESUME  
1 Press [DISC MENU].  
1 During playback, press [STOP C].  
DISC  
MENU  
Resume ON  
STOP  
Press ’PLAY’ to play from here.  
To play the beginning,  
press ’STOP’ first and then ’PLAY’.  
The DVD main menu will appear.  
If the feature is not available,  
appear on the TV screen.  
symbol may  
If disc menu is available on the disc, audio lan-  
guage, subtitle options, chapters for the title and  
other options will appear for selection.  
Resume message will appear on the TV screen.  
2 Press [K], [L], [s] or [B] to select an item  
2 Press [PLAY O], playback will resume from  
and press [ENTER] to confirm selection.  
the point at which playback was stopped.  
PLAY  
ENTER  
To cancel resume, press [STOP C] twice.  
For MP3, playback will resume from the begin-  
ning of the current track.  
The resume information stays on even when the  
power is turned off.  
TITLE MENU  
PAUSE  
1 Press [TITLE].  
TITLE  
The title menu will appear.  
If the feature is not available,  
appear on the TV screen.  
1 During playback, press [PAUSE F].  
symbol may  
PAUSE  
2 Press [K], [L], [s] or [B] to select an item  
Playback will pause and sound will be muted.  
then press [ENTER] to confirm selection.  
2 To continue playback, press [PLAY O].  
ENTER  
PLAY  
STEP BY STEP PLAYBACK  
CALLING UP A MENU SCREEN  
DURING PLAYBACK  
Press [DISC MENU] to call up the DVD menu or  
press [TITLE] to call up the title menu.  
1 During playback, press [PAUSE F].  
NOTE  
PAUSE  
Contents of menu and corresponding menu  
operations may vary between discs. Refer to  
the manual accompanying the disc for details.  
Playback will pause and sound will be muted.  
2 The disc goes forward by one frame each  
time [PAUSE F] is pressed.  
PAUSE  
3
To exit step by step playback, press [PLAY O].  
PLAY  
EN  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FAST FORWARD /  
FAST REVERSE  
ZOOM  
The Zoom function allows you to enlarge the video  
image and to pan through the enlarged image.  
1 During playback, press [FWD g] or  
[REV h].  
1 Press [ZOOM] during playback.  
REV  
FWD  
ZOOM  
SLOW  
Playback will continue.  
g 1” or h 1” appears on the screen.  
2 Press [ZOOM] repeatedly to select the  
required zoom factor: ZOOM1, ZOOM2,  
ZOOM3 or OFF.  
2 To select another speed, repeat step 1 until  
your required speed number appears on the  
screen.  
ZOOM  
For DVDs, fast forward/reverse search speed is  
different depending on the disc. Approximate  
speed is 1(×2), 2(×8), 3(×20), 4(×50) and  
5(×100).  
3 Press [K], [L], [s] or [B] to move the  
zoomed picture across the screen.  
For Audio CDs and  
CD-RW/-R with MP3 files,  
approximate speed is 1(×2), 2(×8) and 3(×30).  
3
To return to normal playback, press [PLAY O].  
PLAY  
4 To exit zoom mode, press [ZOOM] to OFF.  
ZOOM  
SLOW FORWARD /  
SLOW REVERSE  
NOTE  
Zooming function does not work while disc  
menu is shown.  
Zooming function is not available on some  
discs.  
It may take several seconds to slide the  
zoomed picture.  
1 During playback, press [PAUSE F].  
PAUSE  
The picture may be distorted if you operate  
other functions repeatedly (ex. [PAUSE F] or  
[REV h], etc.) in the zoom mode.  
2 Press [FWD g] or [REV h].  
REV  
FWD  
SLOW  
1” or “  
1” appears on the screen.  
3 To select another speed, repeat step 2 until  
your required speed number appears on the  
screen.  
Slow forward or reverse speed varies with the  
disc. Approximate speed is 1(1/16), 2(1/8) and  
3(1/2).  
4
To return to normal playback, press [PLAY O].  
PLAY  
EN  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SEARCH FUNCTION  
2 Within 30 seconds, select the desired track  
1
2
5
8
0
3
CH.  
number using the Number buttons.  
4
6
1
4
7
2
5
8
3
6
9
7
SLEEP  
9
+100  
VOL.  
+10  
0
SKIP  
ZOOM  
MUTE  
To select single-digit track number, press [0]  
first if the total number of track in the disc is 10  
or more. (e.g. Press [0] [3] for track number 3.)  
Playback will start at the selected track.  
PLAY  
STOP  
REV  
FWD  
DISC  
MENU  
PAUSE SLOW  
DISPLAY  
Using [SKIP H / G  
]
During playback, press [SKIP G] to move the next  
track. Press it repeatedly to skip subsequent tracks.  
Press [SKIP H] to go back to beginning of the cur-  
rent track. Press it repeatedly to go to the previous  
tracks.  
ENTER  
SETUP  
TITLE  
RETURN  
CLEAR SEARCH MODE REPEAT  
A-B  
If [SKIP H / G] is pressed while the play-  
back is paused, the playback will be paused  
again after skipping to the next track.  
Shaded buttons are used for following operation.  
NOTE  
TRACK SEARCH  
[SKIP H / G] are not operative when  
playback is stopped.  
There are three ways to begin playback on an Audio CD and  
at a specific track.  
CD-RW/-R with MP3 files  
TITLE / CHAPTER SEARCH  
Using the Number buttons  
1 Press the Number buttons to enter the  
desired track number.  
1 Press [SEARCH MODE] once for the Chapter  
search, twice for the Title search during play-  
back.  
1
4
7
2
5
8
3
6
9
+100  
_/2  
SEARCH MODE  
0
+10  
once  
Playback will start at the selected track.  
To select single-digit track number, press single  
number. (e.g. Press [3] for track number 3.)  
To select track numbers which are higher than 9,  
press [+100/+10] first.  
2 Within 30 seconds, enter the desired chapter/  
title number using the Number buttons.  
1
4
7
2
5
8
3
6
9
(e.g. Press [+100/+10] [2] [5] for track number  
25.)  
0
Using [SEARCH MODE]  
Playback will start at the selected chapter or  
title.  
Press [CLEAR] to erase the incorrect input.  
To select single-digit chapter/title number, press  
[0] first if the total number of chapter/title in the  
disc 10 or more. (e.g. Press [0] [2] for  
chapter/title 2.)  
1 Press [SEARCH MODE].  
SEARCH MODE  
The track search display appears.  
EN  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TIME SEARCH  
MARKER SET UP SCREEN  
Use markers to memorize your favorite places on a disc.  
1 During playback, press [SEARCH MODE]  
repeatedly to display the Time Search on the  
TV screen.  
1 Press [SEARCH MODE] repeatedly during  
playback to display the Marker screen.  
_:_ _:_ _ TOTAL 1:29:00  
SEARCH MODE repeatedly  
1
2
3
4
5
6
7
8
9
10 AC  
SEARCH MODE  
_ _  
_
_:_ _:_ _  
repeatedly  
2 Within 30 seconds, enter a desired disc time  
2 Press [s] or [B] to select 1, 2, 3, 4, 5, 6, 7,  
using the Number buttons.  
8, 9, or 10 and ensure that “  
:
:
- - - - - - - -  
appears in the display.  
1
4
7
2
5
8
3
6
9
0
3 When you reach the desired point, press  
Playback will start at the specified time.  
Press [CLEAR] to erase the incorrect input.  
When there is no need to enter a number, “0”  
appears automatically. For example,  
[ENTER].  
ENTER  
“ 0 : 0 : ” appears in the Time Search display  
if the total time of the track or title is less than  
10 minutes.  
- - -  
The Title or Track and elapsed playing time will  
appear in the TV screen.  
4 To return to the Marker later, press [SEARCH  
MODE] repeatedly during playback to display  
the Marker screen. Then press [s] or [B] to  
choose the desired marker, then press  
[ENTER].  
SEARCH MODE  
ENTER  
repeatedly  
NOTE  
Operations which erase all Markers:  
– Turning off the power.  
– Ejecting a disc from the unit.  
– Pressing [SELECT].  
Selecting “AC” at step 2 and pressing [ENTER].  
To clear a marker:  
– Press [s] or [B] to select a cursor on to  
the marker number and press [CLEAR].  
You can mark up to 10 points.  
5 Press [SEARCH MODE] or [RETURN] to  
exit.  
SEARCH MODE  
RETURN  
OR  
EN  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPECIAL PLAYBACK FUNCTION  
PLAY  
For MP3  
REV  
FWD  
STOP  
DISC  
MENU  
1 Press [REPEAT] during playback.  
PAUSE SLOW  
DISPLAY  
REPEAT  
ENTER  
The repeat mode changes as described below  
every time you press the button.  
SETUP  
TITLE  
RETURN  
CLEAR SEARCH MODE REPEAT  
A-B  
TRACK  
(current track  
repeat)  
GROUP  
(current group  
repeat)  
ALL  
(entire disc  
repeat)  
OFF  
(repeat off)  
AUDIO SUBTITLE ANGLE  
MODE  
Shaded buttons are used for following operation.  
NOTE  
Repeat Track/Group setting will be cleared  
when moving to other track or group.  
REPEAT  
REPEAT is available only during playback.  
A-B REPEAT  
For DVD-Vs  
1 To activate the repeat function, press  
[REPEAT] during playback.  
REPEAT  
1 Press [A-B] at your chosen starting point.  
A-B  
The repeat mode changes as described below  
every time you press the button.  
A-” appears briefly on the TV screen.  
2 Press [A-B] again at your chosen end point.  
CHAPTER  
(current chapter repeat) (current title repeat)  
TITLE  
OFF  
(repeat off)  
A-B  
A-B” appears briefly on the TV screen, and  
the repeat sequence begins.  
NOTE  
Repeat Title/Chapter is not available with  
some scenes.  
Repeat setting will be cleared when moving  
to other title or chapter.  
3 To exit the sequence, press [A-B].  
A-B  
NOTE  
The A-B repeat section can only be set within  
the current title (for DVDs) or current track  
(for Audio CDs).  
A-B repeat is not available with some scenes in DVD.  
To cancel the A point which was set, press  
[CLEAR].  
For Audio CDs  
1 To activate the repeat function, press  
[REPEAT] during playback.  
REPEAT  
A-B repeat playback does not function during  
title, chapter, track or all repeat playback.  
The repeat mode changes as described below  
every time you press the button.  
TRACK  
(current track repeat)  
ALL  
OFF  
(repeat off)  
(entire disc repeat)  
NOTE  
Repeat setting will be cleared when moving  
to other track.  
Repeat playback does not function during  
A-B repeat playback.  
- 23 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PROGRAM  
RANDOM PLAYBACK  
You may determine the order in which tracks will play. This function shuffles the playing order of tracks  
instead of playback in the sequence.  
1 In stop mode, press [MODE].  
1 In stop mode, press [MODE] twice.  
MODE  
RANDOM  
CD-DA  
TOTAL 0:45:55  
The “PROGRAM” screen will appear.  
MODE  
RANDOM PROGRAM  
no indication  
twice  
-
-
-
-
2 Press [] or [] to select a track, then press  
PLAY  
[ENTER].  
<Example : CD>  
“RANDOM” screen appears.  
TOTAL 1:03:30  
1
5
3:30  
5:10  
10 4:20  
11 3:00  
12 3:20  
17 4:10  
22 2:50  
2/3  
2 Press [PLAY O] to start random playback.  
ENTER  
1/4  
PLAY  
<Example : CD>  
Press [CLEAR] to erase the most recently  
NOTE  
If you like to repeat the current track in the ran-  
dom selection, press [REPEAT] several times  
until “  
you like to repeat the entire random selection  
press [REPEAT] several times until “  
appears during playback.  
entered track.  
If the entire Program cannot be displayed at  
once on a screen, Gappears to go to the next  
page and Happears to go back to the previ-  
ous page.  
TRACK” appears during playback. If  
ALL”  
While an MP3 folder is open:  
Press [ B] when you want to go to the next  
hierarchy.  
Press [s ] when you want to go back to the  
previous hierarchy.  
3 Repeat step 2 until you have selected all the  
tracks you want to play in the program.  
4
Press [PLAY O] to play the programmed tracks.  
PLAY  
NOTE  
While the program is being played back,  
pressing [STOP C] works as follows.  
Press [STOP C] once and then [PLAY O]  
again, playback will restart from the point  
where [STOP C] was pressed. (Program con-  
tinued)  
Press [STOP C] twice and then [PLAY O]  
again, playback will restart from the track in  
the usual way. (Program canceled)  
Up to 99 tracks can be entered.  
To erase all tracks in the program at once, select  
“ALL CLEAR” at the bottom of the list at step 2.  
If you like to repeat the current track in the  
program, press [REPEAT] several times until  
TRACK” appears during playback. If you  
like to repeat the entire program press  
[REPEAT] several times until “  
appears during playback.  
ALL”  
EN  
- 24 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CHANGING THE SETTINGS  
DISPLAY  
ENTER  
AUDIO LANGUAGE  
SETUP  
TITLE  
RETURN  
CLEAR SEARCH MODE REPEAT  
A-B  
AUDIO SUBTITLE ANGLE  
The unit allows you to select a language during DVD  
MODE  
disc (if multi languages are available) playback.  
Shaded buttons are used for following operation.  
1 Press [AUDIO] during playback.  
1.ENG Dolby D 3/2.1ch 48k/3  
SUBTITLE LANGUAGE  
AUDIO  
2 Press [AUDIO] repeatedly to select your  
The unit allows you to select a language for subtitles  
during DVD disc (if available) playback.  
desired language.  
AUDIO  
1 Press [SUBTITLE] during playback.  
NOTE  
1.ENG/6  
Pressing [AUDIO] may not work on some  
SUBTITLE  
DVDs with multiple audio languages (e.g.  
DVDs which allow audio language setting on  
the disc menu).  
The subtitle language will appear on the display  
bar at the top of the TV screen.  
2 Press [SUBTITLE] repeatedly to select your  
desired subtitle language.  
STEREO SOUND MODE  
SUBTITLE  
3 To turn off subtitles, press [SUBTITLE]  
repeatedly until “OFF” appears.  
1
Press [AUDIO] repeatedly during playback to  
select between “STEREO”, “L-ch” or “R-ch”.  
SUBTITLE  
STEREO  
AUDIO  
NOTE  
Pressing [SUBTITLE] may not work on  
STEREO : Both right and left channels are active  
(stereo)  
some DVDs with multiple subtitle languages.  
In this case, set it on the disc menu.  
(Operation varies between discs. Refer to the  
manual of the disc.)  
L-ch :  
R-ch :  
Only left channel is active  
Only right channel is active  
If the desired language is not shown after  
pressing [SUBTITLE] several times, the disc  
does not have subtitles in that language.  
When “NOT AVAILABLE” appears on the TV  
screen, it means no subtitle is recorded on the  
scene.  
NOT AVAILABLE  
If you choose a language that has a 3 letter  
language code, the code will be displayed  
every time you change the Subtitle language  
setting. If you choose any other languages,  
“---” will be displayed instead. (Refer to page  
31.)  
- 25 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CAMERA ANGLE  
VIRTUAL SURROUND  
Some DVD discs contain scenes which have been shot You can enjoy surround-sound effect over two speak-  
simultaneously from various angles. You can change ers on this unit.  
the camera angle when the “  
screen.  
icon appears on the  
1 Press [MODE] repeatedly during playback  
then press [ENTER] to set it “1”, “2” or “OFF”.  
1 Press [ANGLE] during playback.  
OFF  
MODE  
ENTER  
repeatedly  
1 / 8  
ANGLE  
1: Natural effect  
The selected angle will be displayed on the dis-  
play bar at the top of the screen.  
2: Emphasized effect  
OFF: Original Sound  
If the “ANGLE ICON” setting is “OFF” in the  
2 Press [MODE] to exit.  
“OTHERS” menu, the “  
icon will not  
MODE  
appear. (Refer to page 30.)  
2 Press [ANGLE] repeatedly to select your  
You can also exit the menu by pressing  
[RETURN].  
desired angle.  
ANGLE  
NOTE  
For Audio CD play only:  
Virtual Surround will not be effective if the  
sound mode is set to something other than  
“STEREO”. (Refer to “STEREO SOUND  
MODE” on page 25.)  
BLACK LEVEL SETTING  
Adjust the Black Level Settings to make the black  
parts of the picture brighter.  
1 Press [MODE] during playback then press  
[ENTER] to switch “ON” or “OFF”.  
OFF  
MODE  
ON: Makes the dark parts brighter.  
OFF: Shows the original picture as recorded.  
(Initial setting)  
2 Press [MODE] twice or [RETURN] to exit.  
MODE twice OR  
RETURN  
NOTE  
The setting will be saved even if the unit is  
turned off.  
EN  
- 26 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
THE ON-SCREEN INFORMATION  
DISPLAY  
2 Press [DISPLAY] again to show current Total  
ENTER  
Track.  
SETUP  
TITLE  
RETURN  
ALL:  
Current track number / Total tracks  
4/12 0:13:45 - 0:45:40  
T
Shaded buttons are used for following operation.  
Current repeat setting appears only  
when the repeat setting is active  
T: Track repeat  
A: All Tracks repeat  
You can check the information about the current disc  
by pressing [DISPLAY].  
A
B: A-B repeat  
Remaining time of the entire disc  
Elapsed time of the entire disc  
For DVD-Vs  
3 Press [DISPLAY] again to exit.  
1 Press [DISPLAY] during playback to show  
current Chapter.  
Angle icon, appears only when avail-  
able on the DVD  
NOTE  
Current playback status  
11/16 0:00:00 - 0:03:30  
When you are playing a disc in PROGRAM  
or RANDOM mode, “ PROGRAM” (or  
“RANDOM”) will be displayed at step 2.  
Remaining time of the current chapter  
Elapsed time of the current chapter  
CH(Chapter):  
Current chapter number / Total chapters  
2
Press [DISPLAY] again to show current Title.  
For MP3  
1/3 0:00:00 - 1:23:45  
1 Press [DISPLAY] during playback.  
Remaining time of the current title  
Current playback status  
Elapsed time of the current title  
3
TRACK 01  
TT(Title):  
Current title number / Total titles  
The name of the file currently in play  
will be displayed.  
3 Press [DISPLAY] again.  
2 Press [DISPLAY] again.  
T
L1  
TR(Track):  
Layer numbers, appears only when  
playing a two-layered Disc  
L0: Layer 0 is playing  
Current track number / Total tracks  
1/36 0:01:15  
T
Current repeat setting, if active  
T: Track repeat  
L1: Layer 1 is playing  
G: Group (folder) repeat  
A: Disc repeat  
Current repeat setting appears only  
when the repeat setting is active  
C: Chapter repeat / T: Title repeat /  
Elapsed playing time of the current  
track  
A
B: A-B repeat  
BIT RATE: The amount of audio and  
video data currently being read  
3 Press [DISPLAY] again to show the  
current playback mode.  
4 Press [DISPLAY] again to exit.  
(Only when you are playing a disc in PROGRAM or  
RANDOM mode.)  
PROGRAM  
RANDOM  
or  
4 Press [DISPLAY] again to exit.  
For Audio CDs  
1 Press [DISPLAY] during playback to show the  
current Track.  
Current playback status  
4/12 0:03:21 - 0:02:15  
T
Remaining time of the current track  
Elapsed time of the current track  
TR(Track):  
Current track number / Total tracks  
- 27 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CHANGING THE DVD SET UP ITEMS  
QUICK MENU  
D
LANGUAGE SETTING  
You can select the “TV MODE” or “DOLBY  
DIGITALfrom the QUICK menu quickly. To  
access the QUICK menu, select “QUICK”  
Follow steps to in the  
CUSTOM MENU  
.
1
2
3 Press [K] or [L] to select the desired item  
instead of “CUSTOM” at step  
.
1
then press [ENTER].  
TV SET UP MENU IN DVD MODE  
SETUP  
LANGUAGE  
You can access the TV SETUP menu by press-  
AUDIO  
SUBTITLE  
DISC MENU  
ORIGINAL  
OFF  
ENGLISH  
ENTER  
ing [SETUP] from the DVD mode, and select  
only “LANGUAGE” and “BACK LIGHT”.  
AUDIO:  
Sets the audio language.  
SUBTITLE: Sets the subtitle language.  
DISC MENU: Sets the language for DVD menu.  
DISPLAY  
ENTER  
SETUP  
TITLE  
RETURN  
4 Press [K] or [L] to select a setting then press  
[ENTER].  
SETUP  
LANGUAGE  
LANGUAGE  
LANGUAGE  
AUDIO  
Shaded buttons are used for following operation.  
You can change the DVD player’s settings.  
ORIGINAL  
ENGLISH  
FRENCH  
ENTER  
SETUP  
CUSTOM MENU  
SUBTITLE  
OFF  
ENGLISH  
FRENCH  
1 In stop mode, press [SETUP] twice, [L] to  
SETUP  
select “CUSTOM” then press [ENTER].  
DISC MENU  
ENGLISH  
FRENCH  
SETUP  
twice  
SPANISH  
SETUP  
If “OTHER” is selected on the “AUDIO”,  
QUICK  
CUSTOM  
INITIALIZE  
ENTER  
“SUBTITLE” or “DISC MENU” screen, press  
four-digit number to enter the code for the  
desired language. (Refer to page 31.)  
NOTE  
Only the languages supported by the disc can be selected.  
If the menu does not appear, press [PLAY O]  
first, then press [STOP C]. Make sure the  
disc is in stop mode, then slowly press  
[SETUP] twice.  
5 Press [SETUP] to exit the menu.  
SETUP  
NOTE  
2 Press [K] or [L] to select the desired item  
then press [ENTER] to confirm.  
Language Setting for Audio and Subtitle are  
not valid for some discs due to default setting  
of the disc. In this case, set them by pressing  
[AUDIO] and [SUBTITLE]. (Refer to page  
25.)  
SETUP  
CUSTOM  
LANGUAGE  
DISPLAY  
AUDIO  
ENTER  
PARENTAL  
OTHERS  
If you select a language that is not supported  
by the disc, subtitle will automatically be set  
OFF and the first item of the audio languages  
will be automatically set.  
Refer to the pages below to set up each item.  
D
E
F
G
H
LANGUAGE: See  
LANGUAGE SETTING  
DISPLAY SETTING  
AUDIO SETTINGS  
PARENTAL CONTROL  
OTHER SETTINGS  
DISPLAY:  
AUDIO:  
See  
See  
DISPLAY SETTING  
E
PARENTAL: See  
OTHERS: See  
Follow steps to in the  
CUSTOM MENU  
.
1
2
EN  
- 28 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DRC (Dynamic Range Control):  
3 Press [K] or [L] to select the below items then  
SETUP  
AUDIO  
press [ENTER].  
DRC  
ON  
DOWN SAMPLING  
DOLBY DIGITAL  
ON  
BITSTREAM  
SETUP  
DISPLAY  
TV MODE  
STILL MODE  
4:3 LETTER BOX  
AUTO  
ENTER  
To compress the range of soft to loud sound.  
The default setting is “ON”.  
TV MODE:  
DOWN SAMPLING:  
QUICK  
SETUP  
AUDIO  
You can change certain aspects of the DVD display  
screens and on-screen messages on the TV screen.  
DRC  
ON  
DOWN SAMPLING  
DOLBY DIGITAL  
ON  
BITSTREAM  
SETUP  
DISPLAY  
TV MODE  
STILL MODE  
4:3 LETTER BOX  
AUTO  
ON : Output in 48 kHz. (default)  
OFF : Output the original sound.  
When playing disc with copyright protection  
If you select “OFF”, copyright protection will be  
activated and sound will be down sampled at  
48kHz.  
4:3 LETTER BOX (default): To show black bars  
on top and bottom of the screen.  
4:3 PAN & SCAN: To show a full height picture  
with both sides trimmed.  
DOLBY DIGITAL:  
Set to “BITSTREAM” when the unit is connected  
to a Dolby Digital Decoder.  
QUICK  
STILL MODE  
This function allows you to adjust picture resolu-  
tion and quality in the still mode.  
:
SETUP  
AUDIO  
SETUP  
DISPLAY  
DRC  
ON  
DOWN SAMPLING  
DOLBY DIGITAL  
ON  
BITSTREAM  
TV MODE  
STILL MODE  
4:3 LETTER BOX  
AUTO  
BITSTREAM: Output a Dolby Digital signal (default)  
AUTO (default): Automatically select the best  
resolution setting (FRAME or FIELD) based on  
the data characteristics of the pictures.  
FIELD: Select “FIELD” when the pictures are  
still unstable even if “AUTO” is selected.  
FIELD stabilizes the pictures, although the pic-  
ture quality may become coarse due to the limit-  
ed amount of data.  
PCM:  
Convert the Dolby Digital to PCM  
(2 channel stereo)  
4 Press [SETUP] to exit the menu.  
SETUP  
G PARENTAL CONTROL  
FRAME: Select “FRAME” to display relatively  
motionless pictures in higher resolution.  
FRAME improves the picture quality, although it  
may unstabilize the pictures due to simultaneous  
output of two field data.  
Parental Control limits the discs viewing that exceed  
your setting (with a password or playback will stop).  
This feature allows you to prevent discs with alterna-  
tive scenes from being played by your children.  
4 Press [SETUP] to exit the menu.  
PARENTAL LEVEL  
SETUP  
Parental Level allows you to set the rating level of  
your DVD discs. Playback will stop if the disc’s rat-  
ings exceed the level you set.  
AUDIO SETTINGS  
Choose the appropriate Audio settings for your equip-  
ment as it only affects during the playback of DVD  
discs.  
F
Follow steps to in the on  
CUSTOM MENU  
1
2
page 28.  
3 Enter your four-digit password then press  
[ENTER].  
Follow steps to in the on  
CUSTOM MENU  
1
2
1
4
7
2
5
8
3
6
9
SETUP  
PARENTAL  
page 28.  
PASSWORD  
Enter current password.  
ENTER  
3 Press [K] or [L] to select the below items then  
press [ENTER].  
0
SETUP  
AUDIO  
Press [4], [7], [3], [7] then enter your password  
if you forget the password.  
DRC  
DOWN SAMPLING  
DOLBY DIGITAL  
ON  
ON  
BITSTREAM  
ENTER  
- 29 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ANGLE ICON:  
4 Press [K] or [L] to select “PARENTAL LEVEL”  
Press [ENTER] repeatedly to turn Angle icon  
“ON” or “OFF”.  
then press [ENTER].  
SETUP  
PARENTAL  
The default setting is “ON”.  
SCREEN SAVER:  
PARENTAL LEVEL  
PASSWORD CHANGE  
ALL  
ENTER  
Press [ENTER] repeatedly to turn Screen Saver  
“ON” or “OFF”.  
5 Press [K] or [L] to select the desired level  
The default setting is “OFF”.  
If you select “ON”, the screen saver program  
starts when there is no input from the unit for 5  
minutes in stop mode.  
then press [ENTER].  
SETUP  
PARENTAL  
PARENTAL LEVEL  
ALL  
ENTER  
8 [Adult]  
7 [NC-17]  
6 [R]  
4 Press [SETUP] to exit the menu.  
SETUP  
6 Press [SETUP] to exit the menu.  
SETUP  
INITIALIZE  
NOTE  
This allows you to return all selections of SETUP  
(except for PARENTALand menu language) to  
their default settings.  
When doing this for the first time, enter any 4  
digits. (except for 4737) That number will be  
used as the password. (in the event you forget  
the password, see below)  
To change the password, press [K] or [L] to  
select PASSWORD CHANGE” at step 4  
then press [ENTER]. Enter the four-digit  
password, then press [ENTER].  
With some DVDs, it may be difficult to find if  
they are compatible with parental control. Be  
sure to check if the parental control function  
operates in the way that you have set.  
1 Press [SETUP] twice in stop mode so that the  
“INITIALIZE” menu appears.  
SETUP  
twice  
2 Press [K] or [L] to select “INITIALIZE” then  
press [ENTER].  
Record the password in case you forget it.  
SETUP  
QUICK  
CUSTOM  
ENTER  
INITIALIZE  
CONTROL LEVELS  
ALL  
3 Press [K] or [L] to select “YES” then press  
All parental controls are canceled.  
Level 8  
DVD software of any grade (adult/general/children)  
can be played back.  
Levels 7 to 2  
Only DVD software intended for general use and  
children can be played back.  
Level 1  
Only DVD software intended for children can be  
played back, with those intended for adult and gen-  
eral use prohibited.  
[ENTER] twice.  
SETUP  
INITIALIZE  
Initialize?  
NO  
ENTER  
YES  
twice  
All the settings (except for PARENTALand  
menu language) will be cleared.  
To cancel the initialization, select “NO”.  
4 Press [SETUP] to exit the menu.  
SETUP  
OTHER SETTINGS  
H
Follow steps to in the on  
CUSTOM MENU  
1
2
page 28.  
3 Press [K] or [L] to select the below items then  
press [ENTER].  
SETUP  
OTHERS  
ANGLE ICON  
SCREEN SAVER  
ON  
OFF  
ENTER  
EN  
- 30 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LANGUAGE CODE LIST  
Language  
Code Language  
Code Language  
Code Language  
Code  
6560  
6550  
6555  
6565  
6557  
6558  
6561  
5165  
6567  
6569  
6568  
Shona  
Sindhi  
Finnish [FIN]  
French [FRE]  
Frisian  
5255  
5264  
5271  
5358  
5747  
5051  
5158  
5758  
5360  
5367  
5447  
5569  
5455  
5467  
Lingala  
5860  
5866  
5957  
5953  
5965  
5958  
5966  
5955  
5964  
5961  
5960  
6047  
6051  
6061  
A-B  
Abkhazian  
Afar  
Afrikaans  
Albanian  
Amharic  
Arabic  
Armenian  
Assamese  
Aymara  
Azerbaijani  
Bashkir  
Basque  
Bengali;Bangla  
Bhutani  
Bihari  
Bislama  
Breton  
4748  
4747  
4752  
6563  
4759  
4764  
5471  
4765  
4771  
4772  
4847  
5167  
4860  
5072  
4854  
4855  
4864  
4853  
5971  
4851  
Lithuanian  
Macedonian  
Malagasy  
Malay  
Malayalam  
Maltese  
Maori  
Singhalese  
Siswat  
Slovak  
Slovenian  
Somali  
Spanish [SPA]  
Sundanese  
Swahili  
Swedish [SWE]  
T
Galician  
Georgian  
German [GER]  
Greek [GRE]  
Greenlandic  
Guarani  
Gujarati  
Hausa  
Hebrew  
Hindi  
Hungarian [HUN]  
I-K  
Icelandic [ICE]  
Indonesian  
Interlingua  
Interlingue  
Inupiak  
Irish [IRI]  
Italian [ITA]  
Japanese [JPN]  
Javanese  
Kannada  
Marathi  
Moldavian  
Mongolian  
Nauru  
Tagalog  
Tajik  
Tamil  
6658  
6653  
6647  
6666  
6651  
6654  
4861  
6655  
6661  
6665  
6664  
6657  
6669  
Nepali  
Norwegian [NOR]  
O-R  
Occitan  
Oriya  
Oromo(Afan)  
Panjabi  
Tatar  
5565  
5560  
5547  
5551  
5557  
5347  
5566  
5647  
5669  
5760  
5765  
5757  
6469  
5771  
6460  
5761  
5767  
6149  
6164  
6159  
6247  
6265  
5247  
6258  
6266  
6367  
6459  
6461  
6467  
Telugu  
Thai  
Tibetan  
Tigrinya  
Tonga  
Bulgarian  
Burmese  
Byelorussian  
Pashto;Pushto  
Persian  
Tsonga  
Turkish [TUR]  
Turkmen  
Twi  
C-E  
Polish [POL]  
Portuguese [POR]  
Quechua  
Rhaeto-Romance  
Romanian [RUM]  
Russian [RUS]  
S
Samoan  
Sangho  
Sanskrit  
Cambodian  
Catalan  
Chinese [CHI]  
Corsican  
5759  
4947  
7254  
4961  
5464  
4965  
5047  
6058  
5160  
5161  
5166  
U-Z  
Kashmiri  
Kazakh  
Kinyarwanda  
Kirghiz  
Kirundi  
Korean [KOR]  
Kurdish  
Ukrainian  
Urdu  
Uzbek  
6757  
6764  
6772  
6855  
6861  
4971  
6961  
7054  
5655  
7161  
7267  
Croatian  
Czech [CZE]  
Danish [DAN]  
Dutch [DUT]  
English [ENG]  
Esperanto  
Estonian  
6559  
6553  
6547  
5350  
6564  
6554  
6566  
6660  
Vietnamese  
Volapuk  
Welsh  
Scots Gaelic  
Serbian  
Wolof  
Xhosa  
L-N  
F-H  
Laothian  
Latin  
Latvian;Lettish  
5861  
5847  
5868  
Serbo-Croatian  
Sesotho  
Setswana  
Yiddish  
Yoruba  
Zulu  
Faroese  
Fiji  
5261  
5256  
If you choose a language that has a 3 letter language code, the code will be displayed every time you change the  
AUDIO or SUBTITLE language setting above. If you choose any other languages, ‘---’ will be displayed instead. (3  
letter language code is written in bracket.)  
CABLE CHANNEL DESIGNATIONS  
If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels  
with letters or letter-number combinations. Please check with your local cable company. The following is a  
chart of common cable channel designations.  
CATV channel  
TV Display  
5A  
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10  
10  
11  
11  
12  
12  
13  
13  
A
B
14  
15  
CATV channel  
TV Display  
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
CATV channel  
R
S
T
U
V
W
W+1  
37  
W+2  
38  
W+3  
39  
W+4  
40  
W+5  
41  
W+6  
42  
W+7  
43  
W+8  
44  
W+9  
45  
TV Display  
31  
32  
33  
34  
35  
36  
CATV channel  
W+10 W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24  
46 47 48 49 50 51 52 53 54 55 56 57 58 59 60  
W+25 W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39  
61 62 63 64 65 66 67 68 69 70 71 72 73 74 75  
W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54  
TV Display  
CATV channel  
TV Display  
CATV channel  
TV Display  
76  
77  
78  
79  
80  
81  
82  
83  
84  
85  
W+59 W+60 W+61 W+62 W+63 W+64  
100 101 102 103 104 105  
86  
87  
88  
89  
90  
W+55 W+56 W+57 W+58  
A-5  
95  
A-4  
96  
A-3  
97  
A-2  
98  
A-1  
99  
CATV channel  
TV Display  
91  
92  
93  
94  
CATV channel  
W+65 W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79  
TV Display  
106  
W+80 W+81 W+82 W+83 W+84  
121 122 123 124 125  
107  
108  
109  
110  
111  
112  
113  
114  
115  
116  
117  
118  
119  
120  
CATV channel  
TV Display  
- 31 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING GUIDE  
If the unit does not perform properly when operated as instructed in this Owner’s Manual, check the unit, con-  
sulting the following checklist.  
PROBLEM  
CORRECTIVE ACTION  
• Make sure the power plug is connected to an AC outlet.  
• Make sure the power is turned on.  
No power  
No operation by infrared remote  
control  
• Check if the power plug is connected to an AC outlet.  
• Check the batteries in the remote control.  
• Aim the remote control directly at the remote sensor. If necessary,  
remove all the obstacles between the sensor and the remote control.  
• Refer to the infrared signal on page 34.  
You have to be within 23 feet (7m) of the unit.  
• Check if the correct mode is selected. If not, switch the mode by  
pressing [SELECT], whichever you need.  
TV Mode  
Sometimes a performance problem can be easily solved by checking seemingly apparent but often overlooked  
possibilities. Before arranging for service, check these items. It could save your time and money.  
PROBLEM  
No picture or sound  
CORRECTIVE ACTION  
• Make sure the AC cord is connected to an AC outlet.  
• Check antenna connection.  
• Press [SELECT] to select TV mode.  
Then try other TV feature.  
• Let the unit program its tuner memory.  
No picture or poor picture on the  
unit  
• Adjust direction or replace antenna.  
• Adjust picture controls.  
• Check for broken pin of the antenna cable.  
• Adjust volume control on remote control or main unit.  
• Press [MUTE] to restore sound.  
No sound or poor sound  
Bars on screen  
• If outside antenna is being used, check for broken wire.  
• Check for local interference.  
Picture distorted or blurred  
• Try a new channel, if OK, then possible station trouble.  
• If outside antenna is being used, check for broken wire.  
• Try a new channel, if OK, then possible station trouble.  
• If outside antenna is being used, check for broken wire.  
• Check for local interference.  
Picture rolls vertically  
Lines or streaks in picture  
No color  
• Try a new channel, if OK, then possible station trouble.  
• Is antenna connected to jack on the back of the set?  
• If outside antenna is being used, check for broken wire.  
• Adjust “COLOR” control.  
Poor reception on some channels  
Ghosts in picture  
• Try a new channel, if OK, then possible station trouble.  
• Is antenna connected to jack on the back of the set?  
• If outside antenna is being used, check for broken wire.  
• Check for local interference.  
Weak picture  
• Try a new channel, if OK, then possible station trouble.  
• Is antenna connected to jack on the back of the set?  
• If outside antenna is being used, check for broken wire.  
• Adjust “CONTRAST” & “BRIGHTNESS” control.  
EN  
- 32 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PROBLEM  
Sound OK, picture poor  
CORRECTIVE ACTION  
• Try a new channel, if OK, then possible station trouble.  
• Is antenna connected to jack on the back of the set?  
• If outside antenna is being used, check for broken wire.  
• Check for local interference.  
• Adjust “CONTRAST” & “BRIGHTNESS” control.  
• Try a new channel, if OK, then possible station trouble.  
• Check for local interference.  
Picture OK, sound poor  
No operation by infrared remote  
control  
• Make sure the AC cord is connected to an AC outlet.  
• Check batteries in remote control.  
CLOSED CAPTION PROBLEM  
POSSIBLE REMEDY  
Misspelling in captions  
• Error committed by the closed captioning production company.  
Possible in a live broadcast. Not in case of a prerecorded program.  
• A few seconds of delay is common for live broadcast.  
• Display capacity may not exceed 220 words per minute. If a dialogue  
exceeds that rate, selective editing is used to insure that the captions  
remain up-to-date with the current TV screen dialogue.  
Text is not shown in its entirety or  
a delay occurs from what is being  
said.  
Captions scrambled with white  
boxes  
• Caused by interferences of building, power lines, thunderstorms, etc.  
No captions in a program which  
must contain closed caption  
• The broadcast may use a time compression process to speed up the  
program. The decoder cannot read the compressed information and  
captions will be lost.  
Black box in the TV screen  
You are in TEXT mode. Select a CAPTION mode (“CAPTION1”,  
“CAPTION2”) or Caption “OFF”.  
NOTE  
The LCD panel is manufactured to provide many years of useful life. Occasionally a few non active pixels  
may appear as a fixed point of blue, green or red. This is not to be considered a defect in the LCD screen.  
- 33 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DVD Mode  
PROBLEM  
CORRECTIVE ACTION  
• Insert a correct video disc that plays on this unit.  
• Press [SELECT] to select DVD mode, then try other DVD feature.  
• Insert the disc.  
No picture  
Disc cannot be played  
• Clean the disc.  
• Place the disc correctly, with the label facing back of the unit.  
• Cancel the parental control or change the control level.  
• Connect the audio cables firmly.  
No sound  
• Turn the power of the audio component on.  
• Correct the audio output settings.  
• Correct the input settings on the audio component.  
• This unit does not support DTS audio. This is not a malfunction.  
• There are some cases where pictures may be slightly distorted, which  
are not a sign of a malfunction.  
No DTS audio is output  
Distorted picture  
• Although pictures may stop for a moment, this is not a malfunction.  
• The selected language is not available for audio or subtitles on the  
DVD. (This is not a malfunction.)  
Audio or subtitle language  
does not match the set up  
The camera angle cannot be changed • The DVD does not contain sequences recorded from different camera  
angles. (This is not a malfunction.)  
Audio or subtitle language cannot be • The DVD does not contain audio source or subtitles in the selected  
changed  
language. (This is not a malfunction.)  
“Prohibited icon” appears on the  
screen, prohibiting an operation  
CD sound dropout  
• That operation is prohibited by the unit or the disc.  
(This is not a malfunction.)  
• Scratched disc. Replace the disc with an unscratched one.  
No CD reproduction  
DVD picture dropout  
DVD picture freeze  
DVD picture in mosaic  
No DVD reproduction  
Disc cannot be inserted  
Disc cannot be taken out  
• Check if any disc is already in.  
• Unplug and plug again the power cord to the outlet, and then press  
[EJECT A] on the remote control.  
• Press and hold [EJECT A] on the unit for more than 5 seconds.  
NOTE  
Some functions are not available in specific modes, but this is not a malfunction. Read the description in  
this Owner’s Manual for details on correct operations.  
Playback from a desired track and random playback are not available during program playback.  
IR SIGNAL CHECK  
Use the AM radio or the digital camera to check if the remote control  
properly sends out the infrared signal. It will help to define the cause of malfunction.  
Using AM radio  
•Tune the AM radio to no broadcasting band.  
Press any button on remote control toward the radio.  
If the radio receives the signal from remote control properly,  
the sound will flutter.  
Using digital camera  
(including built-in camera of cellular phone)  
•Press and hold any button on remote control toward  
a digital camera. The remote control is working  
if you confirm infrared light through the digital camera.  
EN  
- 34 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
CABINET CLEANING  
DISC HANDLING  
Handle the discs so that fingerprints and dust do not  
adhere to the surfaces of the discs.  
Wipe the front panel and other exterior surfaces of the  
unit with a soft cloth immersed in lukewarm water and  
wrung dry.  
Never use a solvent or alcohol. Do not spray insecticide  
liquid near the unit. Such chemicals may cause damage  
and discoloration to the exposed surfaces.  
SERVICING  
Should your unit become inoperative, do not try to cor-  
Always store the disc in its protective case when it is not used.  
rect the problem by yourself. There are no user-service-  
able parts inside. Turn off, unplug the power cord and  
please call our help line mentioned on the front page,  
to locate an Authorized Service Center.  
IF THE LASER OPTICAL PICKUP UNIT  
IS DIRTY  
To clean-off, use a soft cloth.  
If the unit still does not perform properly when it is oper-  
Do not use a hard cloth since this will mar the disc.  
Wipe the disc in a straight line from center to edge.  
Never wipe with a circular motion.  
ated, while referring to the relevant sections and to  
“TROUBLESHOOTING GUIDE” in this Owner’s  
Manual, the laser optical pickup unit may be dirty.  
Consult your dealer or an Authorized Service Center for  
inspection and cleaning of the laser optical pickup unit.  
Do not use detergent or abrasive cleaning agents.  
PICTURE SCREEN CLEANING  
If the liquid crystal display panel should require clean-  
ing, wipe it with a cotton or soft cloth. Before cleaning  
the picture screen, disconnect the power cord.  
SPECIFICATIONS  
GENERAL SPECIFICATIONS  
ELECTRICAL SPECIFICATIONS  
Sound output:  
2 speakers, 1W, 8 ohm  
TV  
OTHER SPECIFICATIONS  
LCD :  
Television system :  
Closed caption system : §15.119/FCC  
Channel coverage:  
VHF:  
UHF:  
CATV:  
20 inch  
Terminals  
NTSC-M  
Antenna input:  
VHF/UHF/CATV  
75 ohm unbalanced (F-type)  
Mini DIN 4-pin jack  
RCA connector [ 1  
S-Video input:  
2 ~ 13  
14 ~ 69  
2 ~13, A ~ W,  
W+1 ~ W+84,  
A-5 ~ A-1, 5A  
181 channels  
frequency synthesized  
tuning system  
Direct access keyboard,  
programmable  
scan and up/down  
Video input:  
Audio L/R input:  
RCA connector [ 4  
Component video input:  
One pin jack (Y), 1Vpp (75 ohm)  
Two pin jacks (Pr)/(Pb), 700mVpp (75 ohm)  
Coaxial digital audio output:  
Tuning System:  
Channel access:  
One pin jack, 500mVpp (75 ohm)  
Headphone:  
1/8" stereo (3.5mm)  
Digital encoded  
Remote control:  
infrared light system  
Operating  
temperature:  
5°C to 40°C  
(41°F~104°F)  
AC 120V, 60Hz  
Power requirements:  
Power consumption  
(Maximum):  
LCD:  
Dimensions:  
DVD  
61W  
20"  
Product type:  
Discs:  
DVD Player  
DVD video, Audio CD  
CD-RW/-R with MP3 files  
H :18-5/16" (465mm)  
W :23-3/8" (594mm)  
D : 9-1/8" (231mm)  
14.8lbs. (6.7kg)  
Weight:  
Designs and specifications are subject to change without notice.  
If there is a discrepancy between languages, the default language will be English.  
- 35 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INDICE  
INDICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36  
CONTROLES DE OPERACIÓN Y FUNCIONES . . . . . 36  
PARA INSERTAR LAS PILAS . . . . . . . . . . . . . . . . . . . . 37  
PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 38  
CONEXIONES DE ANTENA/CABLE . . . . . . . . . . . . . . 38  
CONEXIÓN EXTERNA . . . . . . . . . . . . . . . . . . . . . . . . . 39  
SECCIÓN DE DVD  
REPRODUCCIÓN DE UN DISCO . . . . . . . . . . . . . . . . 42  
REPRODUCCIÓN BÁSICA . . . . . . . . . . . . . . . . . . . . . . 42  
MENÚ DE DISCO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43  
REANUDACIÓN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43  
SECCIÓN DE TV  
OPERACIÓN DE TV Y AJUSTES . . . . . . . . . . . . . . . . . 40  
INSTALACIÓN INICIAL . . . . . . . . . . . . . . . . . . . . . . . . 40  
PARA MIRAR UN PROGRAMA DE TV . . . . . . . . . . . . 40  
AJUSTE DE CANAL . . . . . . . . . . . . . . . . . . . . . . . . . . . 41  
IDIOMA DE MENÚ . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41  
CONTROLES DE OPERACIÓN Y FUNCIONES  
NOTA  
Para elegir el modo de DVD presione primero [PLAY O] o [EJECT A], o introduzca un disco en la ranu-  
ra. De otra manera, el DVD no funcionará.  
- MANDO A DISTANCIA  
• Para saber cómo funciona el mando a distancia, consulte la [Fig.1] de la página 7.  
1.Botón POWER  
11. Botón CLEAR  
Presione para encender y apagar la unidad.  
Presione para cancelar o borrar un ajuste intro-  
ducido actualmente.  
2.Botón PICTURE  
Presione para ajustar la imagen.  
3.Botones numéricos  
Presione para seleccionar directamente el número  
de canal deseado.  
Botón +100 (para modo TV)  
Presione para seleccionar canales cuyo número  
sea superior a 99.  
Botón +10 (para modo DVD)  
Presione para introducir los números superiores a  
9 deseados.  
Presione para borrar la pantalla “DISCO ADEN-  
TRO”.  
12. Botón MODE  
Presione para visualizar la pantalla de la repro-  
ducción programada o la de reproducción aleato-  
ria en el modo de parada.  
Presione para visualizar la pantalla de ajuste del  
nivel del negro o la pantalla de sonido envolvente  
durante la reproducción.  
13. Botón SEARCH MODE  
Presione para localizar un punto deseado.  
4.Botón SLEEP  
Presione para ajustar el temporizador de reposo.  
14. Botón AUDIO  
Para modo TV: Presione para seleccionar el  
modo de sonido de TV (ESTEREO/SAP/MONO).  
Para modo DVD: Presione para seleccionar un  
idioma de audio deseado (si está disponible).  
5.Botones SKIP H /  
G
Presione una vez para omitir capítulos o pistas y  
desplazarse a un punto específico.  
6.Botón PLAY  
Presione para reproducir el disco.  
7.Botón PAUSE  
O
15. Botón EJECT  
A
Presione para extraer un disco de la unidad.  
F
16. Botón SELECT  
Presione para hacer una pausa en la reproducción  
del disco actual.  
Presione para seleccionar el modo TV, modo de  
entrada externa o modo de DVD.  
8.Botón DISPLAY  
Para modo TV  
17. Botones CH. K /  
L
:
Presione para seleccionar canales memorizados.  
Presione para visualizar el número actual de canal en  
la pantalla del televisor.  
18. Botones VOL. X /  
Y
Para modo DVD  
:
Presione para controlar el nivel de volumen del  
DVD y el televisor.  
Presione para visualizar el estado actual en la pan-  
talla del televisor.  
19. Botón MUTE  
9.Botón SETUP  
Presione para entrar o salir del menú de configu-  
ración del TV/DVD.  
Presione para silenciar el sonido. Presiónelo de  
nuevo para restablecer el sonido.  
20. Botón ZOOM  
10. Botón TITLE  
Presione para ampliar la parte de la imagen repro-  
ducida en un DVD.  
Presione para visualizar el menú de títulos.  
ES  
- 36 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
26. Botón RETURN  
21. Botón REV  
h
Presione para volver a la pantalla anterior en el  
menú de configuración.  
Presione para ver la imagen en DVD en retroceso  
o en cámara lenta de retroceso.  
27. Botón A-B  
Botón FWD  
Presione para mover en avance rápido o en  
cámara lenta en el disco.  
g
Presione para repetir la reproducción de una sec-  
ción seleccionada.  
28. Botón ANGLE  
22. Botón STOP  
C
Presione para cambiar el ángulo de la cámara y  
ver la secuencia que se está reproduciendo desde  
un ángulo diferente (si existe).  
Presione para detener la reproducción del disco.  
23. Botón DISC MENU  
Muestra el menú del DVD.  
29. Botón REPEAT  
24. Botón ENTER  
Repite la reproducción del disco, título, capítulo,  
grupo o pista actual.  
Presione para establecer un ajuste.  
25. Botones  
K
(Arriba) /  
L
(Abajo) /{  
(Izquierda) /  
30. Botón SUBTITLE  
B
(Derecha)  
Presione para seleccionar el idioma de los subtí-  
tulos.  
Presione para seleccionar o ajustar los ítems del  
menú.  
- PANEL DE CONTROL  
• Para ver la ilustración del panel de control, vaya a la página 8, [Fig. 2].  
31. Botón MENU  
36. Botones CHANNEL L /  
K
Presione para entrar o salir del menú de configu-  
ración del TV/DVD.  
Presione para seleccionar canales memorizados.  
37. Botón SELECT  
32. Botón STOP  
Presione para detener la reproducción del disco.  
33. Botón PLAY  
Presione para reproducir el disco.  
34. Botón EJECT  
Presione para extraer un disco de la unidad.  
35. Botones VOLUME Y /  
C
Presione para seleccionar el modo TV, modo de  
entrada externa o modo de DVD.  
B
38. Botón POWER  
Presione para encender y apagar la unidad.  
A
39. Ventanilla del sensor de mando a distancia  
X
Presione para controlar el nivel de volumen del  
DVD y el televisor.  
PARA INSERTAR LAS PILAS  
PRECAUCIONES A LA HORA DE  
INSERTAR LAS PILAS  
1 Abra la cubierta del compartimiento de las  
pilas empujando la cubierta del mando a dis-  
tancia en el sentido de la flecha.  
Asegúrese de seguir la polaridad correcta, tal como  
se indica en el compartimiento de las pilas. Si se  
colocan las pilas con la polaridad invertida se  
pueden ocasionar daños a la unidad.  
2 Inserte 2 pilas “AA” en el compartimiento de  
las pilas, en el sentido indicado por las mar-  
cas de polaridad (+/-).  
No mezcle distintos tipos de pilas (ej. alcalina y de  
carbón-zinc) o pilas viejas con nuevas.  
3 Vuelva a poner la cubierta.  
Si no va a usarse la unidad durante un período  
largo de tiempo, quite las pilas para prevenir daños  
o lesiones ocasionadas por posibles fugas de las  
pilas.  
No intente recargar las pilas que no sean para  
recargar; pueden sobrecalentarse y estropearse.  
NOTA  
No se recomienda el uso de mandos a distancia universales. No todas las funciones pueden controlarse  
con un mando a distancia universal.  
Si decide usar un mando a distancia universal con esta unidad, sea consciente de que el número de código  
suministrado puede no adecuarse a la unidad. En este caso, llame al fabricante del mando a distancia uni-  
versal.  
- 37 -  
ES  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREPARACIÓN PARA LA UTILIZACIÓN  
CONEXIONES DE ANTENA/CABLE  
NOTA  
Los cables utilizados aquí están disponibles en los comercios.  
Para su seguridad y para evitar daños a la unidad, desconecte el cable de antena de la toma ANT  
antes de trasladar la unidad.  
- CONEXIONES DE ANTENA/CABLE  
SI TIENE UNA TOMA DE PARED  
Conecte el televisor a la toma de antena de pared con  
el cable RF (disponible en los comercios).  
[Parte posterior de  
este unidad]  
SI TIENE CABLE DE HILOS  
DIGITAL  
AUDIO OUT  
(COAXIAL)  
Conecte el televisor al cable de antena.  
2
O
E
R
L
D
I
V
O
P
I
D
U
A
T
N
E
r
N
Y
NOTA  
O
M
P
C
b
P
Antes de conectar la antena en la toma ANT de la unidad,  
compruebe que la patilla no esté torcida. Si lo está, ponga la  
patilla recta tal como se muestra en la ilustración y a contin-  
uación conecte la patilla a la toma ANT de la unidad.  
Patilla torcida  
P
R
L
O
I
D
U
A
1
O
E
O
E
ID  
V
D
I
V
O
E
D
I
V
-
S
T
N
A
E
N
O
H
P
D
A
E
H
desde Señal del TV  
cable o Antena  
Cable  
Conector  
Cable RF  
(Debe ponerse  
recta)  
(patilla recta)  
ANT  
- CONEXIÓN CON CAJA DE CONVERTIDOR /CAJA DE SATÉLITE  
CUANDO SE USA UNA CAJA DE CON-  
VERTIDOR/CAJA DE SATÉLITE  
[Parte posterior de este unidad]  
Si su compañía de televisión por cable le suministra  
una caja de convertidor o si usa un sistema de  
satélite, podrá utilizar la conexión básica que se  
muestra anteriormente.  
La selección de los canales deberá hacerse con la  
caja de convertidor o caja de satélite. Esto significa  
que no es posible cambiar de canal utilizando el  
mando a distancia de la unidad.  
L
O
A
O
X
T
U
L
T
I
G
I
)
D
A
(
I
D
A
I
U
A
O
C
2
O
E
R
L
D
I
Caja de convertidor  
o caja de satélite  
V
O
I
D
U
A
T
N
E
N
Y
O
P
M
P
C
Pb  
Pr  
R
L
O
I
D
U
A
1
O
SALIDA  
ENTRADA  
E
O
D
I
E
V
D
I
V
S-VIDEO  
T
N
A
E
N
O
H
P
D
A
E
H
Cable coaxial  
de 75 ohmios  
T
N
A
desde Compañia de Cable o  
plato del satélite  
NOTA  
Para el instalador de sistemas CATV:  
Esta nota tiene la finalidad de llamar la atención del instalador de sistemas CATV para que tenga en cuenta el  
Artículo 820-40 de la NEC, que proporciona recomendaciones para hacer una conexión a tierra apropiada y, en par-  
ticular, especifica que la tierra del cable debe conectarse al sistema de puesta a tierra del edificio, tan cerca del punto  
de entrada del cable como sea posible.  
ES  
- 38 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONEXIÓN EXTERNA  
Puede conectar esta unidad a su equipo de audio/vídeo.  
Asegúrese de apagar todos los componentes del  
sistema antes de conectar otro componente.  
Consulte los manuales de instrucciones de los  
componentes que va a conectar a la unidad.  
NOTA  
Cuando utilice las tomas de entrada externa, seleccione  
“AUX1” o “AUX2” presionando [SELECT]. (Consulte  
la página 40.)  
L
O
UT  
)
ITA  
IO  
IG  
AUDIO  
L
D
A
D
U
XIA  
A
O
(C  
2
O
E
D
R
L
I
V
O
I
D
U
A
T
N
E
r
N
Y
O
P
M
P
C
b
VIDEO2  
VIDEO1  
P
P
R
L
O
I
D
U
A
1
O
E
O
E
ID  
V
D
I
V
S-VIDEO  
T
N
A
Para utilizar la tomas VIDEO1, seleccione  
“AUX1”.  
E
N
O
H
P
D
A
E
H
Para utilizar la tomas VIDEO2, seleccione  
“AUX2”.  
Use esta conexión si su propio equipo A/V (ej.  
videograbadora) tiene tomas de salida de audio y  
vídeo. Cuando se usa un cable Vídeo-S, se obtiene  
una imagen mejor.  
- ENTRADA DE VÍDEO1  
ej.  
Cable de audio (SALIDA)  
R
IO  
L
D
U
A
(SALIDA)  
Cable de vídeo  
1
O
E
ID  
V
O
E
E
ID  
V
O
Videograbadora  
O
ID  
-V  
S
Cable VIDEO-S (SALIDA)  
NOTA  
Si su propio equipo es monofónico (sólo tiene una toma de audio), conecte el cable de audio a la toma AUDIO L de esta unidad.  
Si conecta la toma VIDEO y la toma S-VIDEO simultáneamente, se da prioridad a la S-VIDEO.  
Use esta conexión si el equipo A/V (ej. videocámara  
o videojuego) tiene tomas de salida de vídeo COM-  
PONENTE (Y,Pb,Pr). Podrá disfrutar de una mejor  
imagen con esta conexión.  
ej.  
- ENTRADA DE VÍDEO2  
2
O
E
ID  
V
(SALIDA)  
(SALIDA)  
Cable de audio  
R
IO  
L
D
U
A
COMPONENT  
Y
Cable de vídeo  
componente  
Pb  
Pr  
Videojuego  
Podrá disfrutar de un sonido de DVD con  
más presencia desconectando el equipo de  
audio digital, tal como el descodificador  
Dolby Digital.  
- SALIDA DE AUDIO  
A toma de ENTRADA  
DIGITAL COAXIAL DE AUDIO  
Equipo doméstico de audio  
Descodificador Dolby Digital  
L
O
IA  
A
IO  
X
IT  
D
A
IG  
U
O
D
A
T
)
U
L
(C  
NOTA  
La fuente de audio de un disco en formato ambiental multicanal Dolby Digital no puede ser grabado  
como sonido digital por una platina MD o DAT.  
Si conecta un descodificador Dolby Digital, ajuste la función “DOLBY DIGITALa “BITSTREAM” para  
salida de audio en el modo de configuración.  
A menos que se haga la conexión a un decodificador “DOLBY DIGITALa “PCM” para salida de audio  
en el modo de configuración.  
La reproducción en una unidad utilizando ajustes incorrectos puede generar ruido y distorsión, y también  
puede provocar daños a los altavoces.  
Fabricado bajo licencia de Dolby Laboratories. “Dolby” y el símbolo de la doble D son marcas comerciales de  
Dolby Laboratories.  
- 39 -  
ES  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECCIÓN DE TV  
OPERACIÓN DE TV Y AJUSTES  
INSTALACIÓN INICIAL  
PARA MIRAR UN PROGRAMA DE TV  
Cuando se enciende la unidad por primera vez, se  
muestra la pantalla de SELECT LANGUAGE.  
Seleccione el idioma de visualización de pantalla y  
ejecute la autoprogramación del canal.  
1 Presione [POWER] para encender la unidad.  
TV  
TV  
POWER  
NOTA  
-
SUGERENCIAS ÚTILES  
-
Si la pantalla del TV muestra  
"interferencias de nieve" y  
no funciona bien durante  
más de 5 segundos,  
aparecerá “SUGERENCIAS ÚTILES”.  
Siga las instrucciones de la pantalla.  
1. VERIFIQUE ANTENA/CABLE/STATÉLITE  
ESTÁ BIEN CONECTADO.  
2. VERIFIQUE “PREA. AUTO CA.” ESTÁ  
BIEN AJUSTADO.  
3. LEA LA PÁGINA FRONTAL DEL MANUAL  
1
Después de finalizar la conexión de la  
antena o del cable, conecte el cable de  
alimentación a una toma estándar de CA.  
DEL USUARIO  
EL NO. TEL. DE AYUDA  
O
PANEL TRASERO PARA  
LOS CLIENTES.  
A
NOTA  
• Si se visualiza algún dígito en la esquina de la  
pantalla, presione [POWER] sin desconectar  
el cable de alimentacíaon.  
Si este ajuste no funciona correctamente,  
llame a nuestro teléfono de asistencia (en la  
portada en este manual del usuario).  
2
Presione [CH. K / L] o los botones numéricos  
para seleccionar el número de canal deseado.  
2 Presione [POWER] para encender la unidad.  
POWER  
1
4
7
2
5
8
3
6
SELECT LANGUAGE  
3 Presione cualquier tecla para  
CH.  
9
O
K
ENGLISH  
ESPAÑOL  
FRANÇAIS  
NEXT:PRESS CH  
DESPUÉS:PRESIONE CH  
APRÈS:PRESSEZ VOL  
seleccionar el idioma del  
menú de pantalla.  
K
+100  
L
X
0
+10  
NOTA  
ENGLISH: [CH.  
ESPAÑOL: [CH.  
FRANÇAIS: [VOL.  
]
]
Para seleccionar el número de canal medi-  
ante los botones numéricos:  
L
X
]
Para seleccionar un número de canal de un  
solo dígito, presione primero [0] (ej. Para el  
4
Confirme la conexión de la antena  
INSTALACIÓN INICIAL  
CABLE  
canal 2, presione [0] [2]).  
CONECTE LA ANTENA  
O
O
K
(o del cable) y presione [CH. ].  
SATÉLITE EN ESTA UNIDAD.  
PRESIONE CH K,  
PARA REALIZAR EL  
“PREA. AUTO CA.”.  
Para seleccionar canales por cable cuyos números  
El sintonizador explora y  
memoriza todos los canales  
activos de su zona.  
sean superiores a 99, presione primero[+100/+10]  
(ej. Para el canal 125, presione [+100/+10] [2] [5]).  
3 Presione [VOL. X / Y] para seleccionar el  
5 Cuando la exploración ha  
finalizado, el sintonizador se  
detiene en el canal  
CA 15  
nivel de volumen deseado.  
VOL.  
VOLUMEN 20  
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
(Ejemplo)  
memorizado más bajo.  
NOTA  
Presione [MUTE] para silenciar el sonido al instante.  
Vuelva a presionarlo para restaurar el nivel de  
volumen anterior.  
Si [MENU] se presiona durante la exploración  
de canales, el sintonizador interrumpe la  
exploración y se muestra el canal memorizado  
más bajo.  
NOTA  
Si presiona [CH. K / L] en el modo DVD,  
puede cambiar los canales del televisor. Incluso  
si apaga la unidad en el modo DVD, cuando  
vuelve a encenderlo se pondrá en el modo TV.  
El menú INSTALACIÓN INICIAL se muestra  
cada vez que usted enciende la unidad a menos  
que la exploración se haya finalizado.  
En caso de que no pueda  
PARA VER UN CANAL POR CABLE O SATÉLITE  
Si la unidad está conectada a una caja de convertidor o  
caja de satélite, presione [CH. K / L] para seleccionar  
CA3 o CA4 según el ajuste de canal de salida del  
aparato, y seleccione en él el canal deseado.  
recibirse ningún canal mediante  
la exploración de canales, “NO  
NO HAY SEÑAL DE TV  
HAY SEÑAL DE TV” aparece  
en pantalla. Apague la unidad y  
compruebe la conexión de la  
PARA VER SEÑALES DE ENTRADA DE  
UN DISPOSITIVO EXTERNO  
Cuando conecte un equipo externo a las tomas de  
entrada delanteras AUDIO/VIDEO, presione  
[SELECT] o [CH. K / L] repetidamente hasta que  
aparezca en la pantalla “AUX1” o “AUX2”.  
antena; a continuación, siga los pasos 1 a 5 otra vez.  
Puede cambiar el después de finalizar la INSTA-  
LACIÓN INICIAL mediante el menú IDIOMA o el  
menú AJUSTE DE CANAL. (Consulte “IDIOMA DE  
MENÚ ” o “AJUSTE DE CANAL” en página 41).  
ES  
- 40 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AJUSTE DE CANAL  
IDIOMA DE MENÚ  
PROGRAMACIÓN AUTOMÁTICA DE CANAL  
1 Presione [SETUP] y a continuación presione  
[K] o [L] para seleccionar el “IDIOMA”.  
De acuerdo con la configuración de fábrica, esta  
unidad ha memorizado todos los canales, incluidos  
los que no están disponibles en su localidad. Esta  
función solo pone automáticamente en memoria los  
canales disponibles.  
- TV PREP. -  
AJUSTE DE CANAL  
AJUSTE DE V-CHIP  
SETUP  
B
IDIOMA  
TITULO  
[ESPAÑOL]  
[OFF]  
LUZ DE FONDO [BRILLO]  
1 Presione [SETUP] y a continuación presione  
2 Presione [ENTER] repetidamente para selec-  
cionar “ENGLISH” = inglés, “ESPAÑOL” o  
“FRANÇAIS”= francés.  
[
K] o [L] para señalar “AJUSTE DE CANAL.  
- TV PREP. -  
B
AJUSTE DE CANAL  
AJUSTE DE V-CHIP  
SETUP  
IDIOMA  
TITULO  
[ESPAÑOL]  
[OFF]  
ENTER  
LUZ DE FONDO [BRILLO]  
3 Presione [SETUP] para salir del menú.  
SETUP  
2 Presione [ENTER] y a continuación presione  
[
K] o [L] para señalar “PREA. AUTO CA..  
– AJUSTE DE CANAL –  
NOTA  
AGREGAR/BORRAR CA (CATV)  
Esta función selecciona sólo el idioma del  
menú de pantalla; no la fuente de audio.  
B
PREA. AUTO CA.  
ENTER  
Si por alguna razón el menú está en español o  
en francés, presione [SETUP], luego [K] o  
[L] para seleccionar “LANGUAGE [ENG-  
LISH]” o “LANGAGE [FRANÇAIS]”, y a  
continuación presione [ENTER] repetida-  
mente para seleccionar el idioma deseado y  
luego presione [SETUP].  
3 Presione [ENTER].  
ENTER  
El sintonizador explora y memoriza todos los  
canales activos de su localidad.  
El sintonizador se detiene en el canal memorizado  
inferior.  
NOTA  
Cuando está activado “PREA. AUTO CA.”  
donde no hay entrada de señal de TV, apare-  
cerá “NO HAY SEÑAL DE TV” en la pan-  
talla después de completarse la exploración  
de los canales.  
La unidad puede reconocer canales CATV  
como canales de TV si las condiciones de  
recepción son malas. En este caso, com-  
pruebe la conexión de la antena y vuelva a  
intentar “PREA. AUTO CA.cuando las  
condiciones de recepción mejoren.  
La autoprogramación del canal NO es  
necesaria cuando la unidad está conectada  
a una caja de convertidor o caja de satélite.  
Sólo tiene que seleccionar el canal para  
caja de convertidor o entrada de satélite  
(ej. CA3 o CA4) de la unidad y a contin-  
uación seleccione el canal que desee en la  
caja de convertidor o la caja de satélite.  
- 41 -  
ES  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECCIÓN DE DVD  
REPRODUCCIÓN DE UN DISCO  
POWER PICTURE SELECT  
EJECT  
5 Precione [EJECT A] para extraer la disco de  
la unidad.  
EJECT  
3
SKIP  
ZOOM  
MUTE  
NOTA  
Cuando el modo DVD se ha cambiado al modo  
TV, el modo DVD se desactiva primero y a  
continuación aparece la imagen y suena el  
sonido en el TV al cabo de unos 4 segundos.  
De la misma manera, cuando se presiona  
[POWER] para apagar la unidad en el modo  
DVD, este modo se desactiva primero y a con-  
tinuación se apaga la unidad.  
PLAY  
STOP  
REV  
FWD  
DISC  
MENU  
PAUSE SLOW  
DISPLAY  
ENTER  
SETUP  
TITLE  
RETURN  
Puede aparecer “  
en la parte superior  
derecha de la pantalla del TV durante su fun-  
cionamiento, que avisa de que el DVD o el  
disco han encontrado una operación prohibida.  
Con los DVD que utilizan títulos para señales  
de reproducción programada, la reproducción  
puede empezar desde el segundo título y  
puede omitir estos títulos.  
Los botones sombreados se utilizan para las sigu-  
ientes operaciones.  
REPRODUCCIÓN BÁSICA  
PARA EMPEZAR  
Durante la reproducción de un disco de dos  
capas, las imágenes pueden detenerse durante  
un rato. Esto ocurre cuando la 1ª capa cambia  
a la 2ª. No se trata de una anomalía.  
Si es necesario, encienda el amplificador y cualquier  
otro componente.  
Si el disco no expulsa en el paso 5, presione y  
1 Presione [POWER] para encender la unidad.  
A
detenga [EJECT ] en la unidad para  
expulsar el disco.  
POWER  
REPRODUCCIÓN DE MP3  
2 Abra la bandeja del disco manualmente.  
1
En el modo de parada, presione [DISC MENU] y precione  
K
L
[ ] o [ ] para seleccionar el grupo o pista que desee.  
LISTA DE ARCHIVOS  
NOMBRE DE DISCO  
Nombre de carpeta 1  
Nombre de carpeta 2  
Nombre de carpeta 3  
Nombre de carpeta 4  
Nombre de archivo 1  
Nombre de archivo 2  
Nombre de archivo 3  
DISC  
3
Introduzca el disco elegido con la etiqueta hacia la  
parte trasera de la unidad para reproducirlo. Al  
presionar suavemente el disco para introducirlo en la  
MENU  
Nombre de carpeta 1  
ranura, su reproducción empezará automáticamente  
,
luego cierre la puerta del disco manualmente.  
Si ha selecciona un grupo, presione [B] o  
[ENTER] para ir a la pantalla de selección de  
pistas. Presione [s] para volver a la pantalla  
anterior (excepto la página superior).  
Si ha seleccionado una pista, presione [ENTER] para  
empezar a reproducir pistas. Si empieza por la que  
acaba de elegir se reproducirán las pistas siguientes.  
La reproducción empezará desde el primer capí-  
tulo/pista del disco.  
Si no puede visualizarse enseguida en pantalla la  
lista entera de archivos, aparece la “ ”para ir a la  
n
Si la reproducción no empieza automáticamente,  
presione [PLAY O].  
Cuando reproduzca un DVD que incluya un menú  
página siguiente.  
Presione [TITLE] para volver al archivo superior  
de la jerarquía más alta del programa y de la  
lista de archivos.  
de títulos, este menú puede aparecer en pantalla.  
4
Presione [STOP C] para detener la reproducción.  
C
2
Presione [STOP ] para detener la reproducción.  
STOP  
STOP  
ES  
- 42 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTA  
REANUDACIÓN  
Las carpetas se conocen como grupos; los  
archivos, como pistas.  
Los archivos MP3 van acompañados de  
3
iconos.  
Se puede reconocer un máximo de 255 carpetas.  
Se puede reconocer un máximo de 999 archivos.  
Pueden crearse hasta 8 jerarquías.  
1 Durante la reproducción, presione [STOP C].  
Se recomienda para esta unidad el uso de archivos  
grabados según las especificaciones siguientes:  
REANUDACIÓN ACTIVADA  
STOP  
Presione 'PLAY' para reproducir  
desde aquí.  
Para reproducir desde el inicio,  
primero presione 'STOP' y luego 'PLAY'.  
Frecuencia de muestreo: 44,1 kHz o 48kHz  
Velocidad de transmisión de bits constante:  
32kbps ~ 320kbps  
Para archivos MP3 grabados en velocidad de trans-  
misión de bits variable (VBR), la unidad puede no  
mostrar el tiempo real transcurrido.  
Aparecerá el mensaje de reanudación en la pan-  
talla del TV.  
2 Presione [PLAY O], la reproducción contin-  
uará desde el punto donde se paró la repro-  
ducción.  
MENÚ DE DISCO  
PLAY  
1 Presione [DISC MENU].  
Para cancelar el modo de reanudación, presione  
dos veces [STOP C].  
Para MP3, la reproducción se reanudará desde el  
principio de la pista actual.  
La información de reanudación permanece activa-  
da incluso cuando apaga el interruptor principal.  
DISC  
MENU  
Aparecerá el menú principal de DVD.  
Si esta función no está disponible,  
el símbo-  
lo puede aparecer en la pantalla del televisor.  
Si el menú de disco está disponible en el disco,  
aparecerán las opciones de idioma de audio, de  
subtítulos, capítulos del título y otras para su  
selección.  
2 Presione [K], [L], [s] o [B] para seleccionar  
un ítem y presione [ENTER] para confirmar la  
selección.  
ENTER  
- 43 -  
ES  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LIMITED WARRANTY  
FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or workmanship  
as follows:  
DURATION:  
PARTS:  
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the  
date of original retail purchase. Certain parts and LCD image burn-in are not covered under this  
warranty.  
LABOR: FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of  
original retail purchase.  
LIMITS AND EXCLUSIONS:  
THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE  
RECEIPT OR OTHER PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH  
THE PRODUCT TO OBTAIN SERVICE UNDER THIS WARRANTY.  
This warranty shall not be extended to any other person or transferee.  
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing or  
if service was attempted by an unauthorized service center. This limited warranty does not apply to any product not  
purchased and used in the United States.  
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It  
does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not  
supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication,  
alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this  
product or damage which results from fire, flood, lightning or other acts of God.  
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE  
CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.  
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY  
GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE  
USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL  
OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF  
FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY AND  
FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS  
REPRESENTATIVES IN THE UNITED STATES.  
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY AN AUTHORIZED  
SERVICE CENTER. THIS WARRANTY IS ONLY VALID WHEN THE UNIT IS CARRIED-IN TO AN  
AUTHORIZED SERVICE CENTER.  
IMPORTANT:  
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS  
THAT VARY FROM STATE TO STATE. IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE  
UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI  
CORP.  
ATTENTION:  
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT  
WITHOUT PRIOR NOTICE.  
WARRANTY STATEMENT REGARDING NON AUTHORIZED REPAIRS:  
To obtain warranty service, you must take the product, or deliver the product freight prepaid, in either its original  
packaging or packaging affording an equal degree of protection, to any AUTHORIZED SERVICE CENTER.  
FUNAI CORP. will not reimburse you for any service done by unauthorized service providers without prior  
written approval.  
To locate your nearest AUTHORIZED SERVICE CENTER or for general service inquiries,  
please contact us at:  
FUNAI CORPORATION  
Customer Service  
Tel :1-800-968-3429  
19900 Van Ness Avenue, Torrance, CA 90501  
Printed in China  
1EMN21903  
L2653UD ★★★★★  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Sharp All in One Printer UX A260 User Manual
Sherwood Stereo Receiver R 771 User Manual
Shuttle Computer Group Personal Computer SH61R4 User Manual
Sony Microphone ECM ZS90 User Manual
Sony MP3 Player TCS 30D User Manual
Specialized Bicycle Accessories HPRT 0027 User Manual
SRS Labs Home Theater System SR554 User Manual
Sterling Fan 25001301 User Manual
SWR Sound Car Speaker 1X10T User Manual
Symphonic Flat Panel Television CSTL1506 User Manual