Sylvania TV DVD Combo 6519DB User Manual

OWNER’S

MANUAL

19-INCH COLOR TV/DVD

6519DB

SUPPLIED ACCESSORIES

ACCESSORIES

Remote Control Unit N0287UD

Batteries 2 AA Batteries

PART NO.

INSTRUCCIONES EN ESPAÑOL INCLUIDAS.

If you need additional assistance for set-up or operating

after reading owner’s manual, please call

TOLL FREE : 1-800-968-3429

Please read before using this equipment.

Download from Www.Somanuals.com. All Manuals Search And Download.

FIGURE A

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

ANTENNA

LEAD I N

WI RE

GROUND

CL AMP

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

ELECTRI C

SERVICE

EQUIPMENT

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

NEC

NATIONAL ELECTRICAL CODE

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

S2898A

12.Power-Cord Protection-Power-supply cords should be

routed so that they are not likely to be walked on or

pinched by items placed upon or against them, paying par-

ticular attention to cords at plugs, convenience receptacles,

and the point where they exit from the appliance.

19.Damage Requiring Service-Unplug this TV/DVD from

the wall outlet and refer servicing to qualified service per-

sonnel under the following conditions:

a. When the power-supply cord or plug is damaged or frayed.

b. If liquid has been spilled, or objects have fallen into the

TV/DVD.

13.Outdoor Antenna grounding-If an outside antenna or

cable system is connected to the TV/DVD, be sure the

antenna or cable system is grounded so as to provide some

protection against voltage surges and built-up static

charges. Article 810 of the National Electrical Code,

ANSI/NFPA No. 70, provides information with respect to

proper grounding of the mast and supporting structure,

grounding of the lead-in wire to an antenna discharge unit,

size of grounding conductors, location of antenna-discharge

unit, connection to grounding electrodes, and requirements

for the grounding electrode. (Fig. A)

c. If the TV/DVD has been exposed to rain or water.

d. If the TV/DVD does not operate normally by following the

operating instructions. Adjust only those controls that are

covered by the operating instructions, as improper adjust-

ment of other controls may result in damage and will often

require extensive work by a qualified technician to restore

the TV/DVD to its normal operation.

e. If the TV/DVD has been dropped or damaged in any way.

f. When the TV/DVD exhibits a distinct change in perfor-

mance-this indicates a need for service.

14.Lightning-For added protection for this TV/DVD receiver

during a lightning storm, or when it is left unattended and

unused for long periods of time, unplug it from the wall

outlet and disconnect the antenna or cable system. This will

prevent damage to the TV/DVD due to lightning and

power-line surges.

20.Replacement Parts-When replacement parts are required,

be sure the service technician has used replacement parts

specified by the manufacturer that have the same character-

istics as the original part. Unauthorized substitutions may

result in fire, electric shock, injury to persons or other haz-

ards.

15.Power Lines-An outside antenna system should not be

located in the vicinity of overhead power lines or other

electric light or power circuits, or where it can fall into

such power lines or circuits. When installing an outside

antenna system, extreme care should be taken to keep from

touching such power lines or circuits as contact with them

might be fatal.

21.Safety Check-Upon completion of any service or repairs to

this TV/DVD, ask the service technician to perform routine

safety checks to determine that the TV/DVD is in proper

operating condition.

22.Heat-This TV/DVD product should be situated away from

heat sources such as radiators, heat registers, stoves, or

other products (including amplifiers) that produce heat.

16.Overloading-Do not overload wall outlets and extension

cords as this can result in a risk of fire or electric shock.

17.Object and Liquid Entry-Never push objects of any kind

into this TV/DVD through openings as they may touch dan-

gerous voltage points or short out parts that could result in

a fire or electric shock. Never spill liquid of any kind on

the TV/DVD.

18.Servicing-Do not attempt to service this TV/DVD yourself

as opening or removing covers may expose you to danger-

ous voltage or other hazards. Refer all servicing to qualified

service personnel.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

PRECAUTIONS

LASER SAFETY

IMPORTANT COPYRIGHT INFORMATION

Unauthorized copying, broadcasting, public perfor-

mance and lending of discs are prohibited.

This unit employs a laser. Only a qualified service

person should remove the cover or attempt to ser-

vice this device, due to possible eye injury.

FCC WARNING- This equipment may gener-

ate or use radio frequency energy. Changes or

modifications to this equipment may cause

harmful interference unless the modifications

are expressly approved in the instruction man-

ual. The user could lose the authority to oper-

ate this equipment if an unauthorized change

or modification is made.

CAUTION: USE OF CONTROLS OR ADJUST-

MENTS OR PERFORMANCE OF PROCE-

DURES OTHER THAN THOSE SPECIFIED

HEREIN MAY RESULT IN HAZARDOUS

RADIATION EXPOSURE.

CAUTION: VISIBLE AND INVISIBLE LASER

RADIATION WHEN OPEN AND INTERLOCK

DEFEATED. DO NOT STARE INTO BEAM.

LOCATION: INSIDE, NEAR THE DECK

MECHANISM.

RADIO-TV INTERFERENCE

This equipment has been tested and found to com-

ply with the limits for a Class B digital device, pur-

suant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and

used in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to

radio or television reception, which can be deter-

mined by turning the equipment off and on, the

user is encouraged to try to correct the interfer-

ence by one or more of the following measures:

1) Reorient or relocate the receiving antenna.

2) Increase the separation between the equipment

and receiver.

This Class B digital apparatus complies with

Canadian ICES-003.

Cet appareil numérique de la classe B est con-

forme à la norme NMB-003 du Canada.

CAUTION: TO PREVENT ELECTRIC SHOCK,

MATCH WIDE BLADE OF PLUG TO WIDE

SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOC

ÉLECTRIQUES, INTRODUIRE LA LAME LA

PLUS LARGE DE LA FICHE DANS LA

BORNE CORRESPONDANTE DE LA PRISE

ET POUSSER JUSQU’AU FOND.

3) Connect the equipment into an outlet on a cir-

cuit different from that to which the receiver is

connected.

4) Consult the dealer or an experienced radio/TV

technician for help.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

LOCATION

WARNING

For safe operation and satisfactory performance of

your TV/DVD, keep the following in mind when

selecting a place for its installation:

Moisture condensation may occur inside the unit

when it is moved from a cold place to a warm place,

or after heating a cold room or under conditions of

high humidity. If a DVD is played in a TV/DVD

which has moisture, it may damage the DVD and

TV/DVD. Therefore when the condensation occurs

inside the unit, turn the POWER button on and allow

at least 2 hours for the unit to dry out.

Shield it from direct sunlight and keep it away from

sources of intense heat.

•

Avoid dusty or humid places.

Avoid places with insufficient ventilation for proper

heat dissipation. Do not block the ventilation holes at

the top and bottom of the unit. Do not place the unit

on a carpet because this will block the ventilation

holes.

•

Install unit in a horizontal position.

Avoid locations subject to strong vibration.

Do not place the TV/DVD near strong magnetic fields.

Avoid moving TV/DVD to locations where temper-

•

ature differences are extreme.

AVOID THE HAZARDS OF

ELECTRICAL SHOCK AND FIRE

Do not handle the power cord with wet hands.

Do not pull on the power cord when disconnecting

it from an AC wall outlet. Grasp it by the plug.

•

If, by accident, water is spilled on your unit, unplug

the power cord immediately and take the unit to our

Authorized Service Center for servicing.

•

Do not put your fingers or objects into the

TV/DVD disc loading tray.

•

Do not place anything directly on top of the unit.

•

A NOTE ABOUT RECYCLING

This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in

accordance with your local recycling regulations.

Batteries should never be thrown away or incinerated but disposed of in accordance with your local regula-

tions concerning chemical wastes.

The serial number of this product may be found on the back of the unit. No other TV/DVD has the same serial

number as yours. You should record the number and other vital information here and retain this book as a per-

manent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.

Date of Purchase

Dealer Purchase from

Dealer Address

Dealer Phone No.

Model No.

Serial No.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

TABLE OF CONTENTS

PAUSING PLAYBACK OR DISPLAYING

A STILL PICTURE . . . . . . . . . . . . . . . . . . . . .22

C IMPORTANT SAFEGUARDS . . . . . . . . . . . . .2

C PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . .4

RESUMING PLAYBACK FROM THE

POINT WHERE PLAYBACK STOPPED . . . .22

LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

AVOID THE HAZARDS OF ELECTRICAL

SHOCK AND FIRE . . . . . . . . . . . . . . . . . . . . . .5

STEPPING THROUGH FRAMES . . . . . . . . . .22

FAST FORWARD/REVERSE . . . . . . . . . . . . .23

SLOW MOTION . . . . . . . . . . . . . . . . . . . . . . .23

STARTING FROM A DESIRED TRACK . . . .23

STARTING FROM A DESIRED TIME COUNT .23

WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

C FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

C SUPPLIED ACCESSORIES . . . . . . . . . . . . . . .7

C OPERATING CONTROLS AND FUNCTIONS 8

PLAYING FROM A DESIRED TITLE OR

CHAPTER . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

C PREPARATION FOR USE . . . . . . . . . . . . . . .10

ANTENNA/CABLE CONNECTIONS . . . . . . .10

INSTALLING THE BATTERIES . . . . . . . . . . .12

RANDOM (Audio CD) . . . . . . . . . . . . . . . . . .24

REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

A-B REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . .25

PROGRAM (Audio CD) . . . . . . . . . . . . . . . . .25

CONNECTING TO EXTERNAL INPUT JACKS .12

CONNECTING TO A STEREO SYSTEM (for DVD) .13

C SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . .26

CONNECTING TO AN AMPLIFIER

EQUIPPED WITH DIGITAL INPUT JACKS,

MD DECK OR DAT DECK (for DVD) . . . . . .13

CHANGING THE AUDIO LANGUAGE OR

SOUND MODE . . . . . . . . . . . . . . . . . . . . . . . .26

CHANGING THE SUBTITLE LANGUAGE . .27

CONNECTING TO A DOLBY DIGITAL

DECODER OR DTS DECODER (for DVD) . .14

CHANGING THE CAMERA ANGLE

(Multi-Angle Pictures) . . . . . . . . . . . . . . . . . . .27

TV SECTION

C SET UP FOR USE . . . . . . . . . . . . . . . . . . . . .15

CHANGING THE ON-SCREEN DISPLAY . . .28

C CHANGING THE SETUP ITEMS . . . . . . . . .29

LANGUAGE SETTINGS . . . . . . . . . . . . . . . .29

VIDEO SETTINGS . . . . . . . . . . . . . . . . . . . . .30

AUDIO SETTINGS . . . . . . . . . . . . . . . . . . . . .30

PARENTAL LOCK . . . . . . . . . . . . . . . . . . . . .31

OTHER SETTINGS . . . . . . . . . . . . . . . . . . . . .32

LANGUAGE SELECTION . . . . . . . . . . . . . . .15

CHANNEL PRESETTING . . . . . . . . . . . . . . .15

C OPERATIONS . . . . . . . . . . . . . . . . . . . . . . . . .16

WATCHING A TV PROGRAM . . . . . . . . . . . .16

SELECTING THE SLEEP TIMER . . . . . . . . .16

CLOSED CAPTION . . . . . . . . . . . . . . . . . . . .16

PICTURE ADJUSTMENT . . . . . . . . . . . . . . . .17

V-CHIP SET UP . . . . . . . . . . . . . . . . . . . . . . . .18

C LANGUAGE CODE LIST . . . . . . . . . . . . . . . .33

C TROUBLESHOOTING GUIDE . . . . . . . . . . .34

DVD SECTION

C ABOUT THE DISCS . . . . . . . . . . . . . . . . . . . .20

C MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . .37

DISC HANDLING . . . . . . . . . . . . . . . . . . . . . .37

PLAYABLE DISCS . . . . . . . . . . . . . . . . . . . . .20

DISC TYPES . . . . . . . . . . . . . . . . . . . . . . . . . .20

SYMBOLS USED IN THIS MANUAL . . . . . .20

C SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . .38

C WARRANTY . . . . . . . . . . . . . . . . . . .Back Cover

C PLAYING A DISC . . . . . . . . . . . . . . . . . . . . . .21

PLAYING A DVD VIDEO OR AN AUDIO CD .21

USING THE DVD MENUS . . . . . . . . . . . . . . .21

USING THE TITLE MENU . . . . . . . . . . . . . . .22

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

FEATURES

¡Tinted, Bright Black Matrix Picture Tube

¡Parental lock

You can set the control level to limit playback of discs

which may not be suitable for children.

¡181 Channel Selection

All VHF/UHF channels plus up to 125 cable channels.

¡Automatic detection of discs

This player automatically detects if a loaded disc is DVD

or audio CD.

¡PLL Frequency Synthesized Tuning

The latest PLL frequency synthesized electronic tuning

system provides free and easy channel selection, and lets

you tune directly to any channel using the channel number ¡On-screen display

buttons (0~9 and +100-key) on the remote control.

¡On-Screen Function Display.

¡Full-Function Remote Control

¡Sleep Timer

Information about the current operation can be displayed

on a TV screen, allowing you to confirm the currently

active functions (such as program playback), on the TV

screen using the remote control.

¡DTS (Digital Theater System)

Sound system different from Dolby Digital sound system

¡Closed Caption Decoder

You may view specially labeled (cc) TV programs,

movies, news, prerecorded tapes, etc. with either a

dialogue caption or text display added to the program.

¡Search

Chapter search: Search for the chapter designated by user

is possible.

Title search:

Search for the title designated by user is

possible.

¡Auto Shut Off Function

If there is no air signal input from the antenna terminal and

no operation for 15 minutes, the TV will turn itself off

automatically.

Track search: Search for the track designated by user is

possible.

Time search: Search for the time designated by user is

possible.

¡V-CHIP

Enables parents to prevent their children from watching

inappropriate material on TV.

¡Repeat

Chapter:

Repeated playback of the chapter of the

disc being played is possible.

Title:

Repeated playback of the title of the disc

being played is possible.

DVD

¡Dolby Digital sound

Track:

Repeated playback of the track of the disc

being played is possible.

This player can handle Dolby Digital surround sound

having 5.1 channels when connected to a Dolby Digital

decoder.

Disc(audio CD): Repeated playback of the entire disc being

played is possible.

A-B:

The part between A and B designated by

user is possible.

¡Still/fast/slow/step playback

Various playback modes are available including still pic-

tures, fast forward/reverse, slow motion and step frames.

¡Zoom

4-time magnified screen can be displayed.

¡Random playback for audio CD

This player can shuffle the order of tracks to play them in

random order.

¡Marker

The part designated by user can be called back.

¡Program playback for audio CD

You can program the order of tracks to play them in any

desired order.

¡Resume Play

User can resume to playback from the part at which the

play was stopped.

¡DVD menus in a desired language

You can display DVD menus in a desired language, if

available on a DVD.

¡SRS TruSurround

You can enjoy stereophonic virtual space on your existing

stereo system.

¡Screen saver/Auto power-off functions

The screen saver program starts when there is no input

from the player for five minutes in the stop mode. When

the screen saver program is activated for 30 minutes, the

power is automatically turned off.

¡Dimmer

Brightness of the display can be varied.

¡Bit rate indication

¡Dynamic range control

¡Subtitles in a desired language

You can select a desired language for the display subtitles,

if that language is available on a disc.

This unit employs TruSurround system

of SRS Labs, Inc. as virtual

technology.

¡Selecting a camera angle

You can select the desired camera angle, if a disc contains

sequences recorded from different angles.

TruSurround and the

SRS Labs, Inc.

symbol are trademarks of

¡Choices for audio language and sound mode

You can select the desired audio language and sound

mode, if different languages and modes are available on a

disc.

TruSurround technology is incorporated under license

from SRS Labs, Inc.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

OPERATING CONTROLS AND FUNCTIONS

[Fig. 1]

TV/DVD FRONT PANEL

VOLUME

CHANNEL

STOP

SKIP

PLAY

SKIP

PAUSE OPEN/CLOSE

HEADPHONE

POWER

VIDEO

L-AUDIO-R

8 181018 12 13 14

5.VOLUME K/L buttons

Press to control the volume level for the DVD and TV.

[Fig. 2]

REMOTE CONTROL

6.CHANNEL K/L buttons

Press to select memorized channel.

Press to change to TV mode when DVD mode.

7.Remote Sensor Window

8.STOP button

Stops operation of the disc.

9.REV button

Fast reverses playback to a desired point.

10. PLAY button

OPEN/

POWER PICTURE SELECT

CH.

SLEEP

+100

VOL.

Starts playback of the disc contents.

Press to change to DVD mode when TV mode.

+10

SKIP

ZOOM

MUTE

11. FWD button

Fast forwards playback to a desired point.

12. PAUSE button

PLAY

STOP

REV

FWD

Pauses the current disc operation.

13. OPEN/CLOSE button

DISC

Press to insert discs into or remove them from the

tray.

PAUSE

DISPLAY

SETUP

14. HEADPHONE jack

ENTER

To connect headphone (not supplied) for personal

listening.

TITLE

RETURN

CLEAR SEARCH MODE REPEAT

A-B

15. MODE button

Activates program playback or random playback mode.

AUDIO SUBTITLE ANGLE

MODE

16. NUMBER button

TV Mode:

Press two digits to directly access the desired

channel.

Remember to press a "0" before a single digit

channel.

+100 button–

1.Disc loading tray

2.VIDEO input jack

Connect to the video output jack of a video

camera or VCR.

3.AUDIO L/R input jacks

Press to select cable channels which are equal or

greater than number 100.

DVD Mode:

Press to enter the desired number.

+10 button–

Connect to the audio output jacks of a video

camera or VCR.

Press to enter the desired numbers which are

equal or greater than number 10.

4.POWER button

Press to turn the power on and off.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

[Fig. 3]

REAR VIEW

ANT.

AUDIO OUT DIGITAL OUT

COAXIAL

39 38

31. ENTER button

17. SLEEP button

Press to accept a setting.

Press the SLEEP button to display the sleep timer

and start the function. The shut off time can be

determined by the number of times you press the

button. (0, 10, 20, 30,..90, 0 minutes)

32. Arrow buttons

TV Mode:

Press to select a setting mode from the menu on

the TV screen.

18. SKIP buttons

Press to select or adjust from a particular menu.

DVD Mode:

Skip chapters or tracks to a desired point.

19. ZOOM Button

Use when making settings while watching the

display on a TV screen.

Enlarges part of a DVD-reproduced image.

20. SETUP button

33. DISC MENU button

Press to enter or exit the TV menu or DVD setup

mode.

Displays the menus in the DVD.

34. SELECT button

21. TITLE button

Press to change to TV mode, external input mode

or DVD mode.

Displays the title menu.

22. CLEAR button

35. MUTE button

Resets a setting.

Press the MUTE button to turn off the sound

portion of the TV program. (Volume level display

turns LIGHT RED from LIGHT BLUE.) Press the

MUTE button again or press the VOL(ume) K or

L button to restore sound.

23. DISPLAY button

TV Mode:

Press to display the channel number on the

screen. If you press it again, the channel number

will disappear.

36. PICTURE button

DVD Mode:

Press to enter picture adjustment mode.

Displays the current status on the TV screen for

checking purposes.

37. Power cord

Connect to a standard AC outlet (120V/60Hz).

NOTE: Remove the power cord from the hook to

avoid breaking a wire before you connect

to a standard AC outlet.

24. SEARCH MODE button

Press to locate a desired point.

25. AUDIO button

Press to select a desired audio language or sound

mode.

38. COAXIAL digital audio out jack

Connect to the digital input of an external

amplifier or decoder.

26. SUBTITLE button

Press to select a desired subtitle language.

39. AUDIO L/R output jack

27. REPEAT button

Connect to the analog audio input of an external

amplifier or decoder.

Repeats playback of the current disc, title, chapter

or track.

NOTE: The AUDIO output jacks (red/white) on

the rear panel serve to give out DVD

sound, not TV sound and external input

sound.

28. ANGLE button

Press to change the camera angle to see the

sequence being played back from a different angle.

29. A-B REPEAT button

40. ANT. in jack

Repeats playback of a selected section.

Connect to an antenna, cable system, or satellite

system.

30. RETURN button

Returns to the previous operation.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

PREPARATION FOR USE

ANTENNA/CABLE CONNECTIONS

VHF/UHF COMBINED ANTENNA

The VHF/UHF Rod Antenna (not supplied) is detachable. Insert the stem of the antenna into the hole on the

upper-back portion of the TV/DVD. Connect the VHF/UHF Rod Antenna or VHF/UHF Combination Antenna

to the ANT. terminal of the TV/DVD as shown in the diagram below. For the best reception, fully extend the

VHF/UHF Rod Antenna and make the necessary adjustments. (Avoid touching the top section when adjusting.)

NOTE:

Before plugging the Rod antenna into antenna terminal, check that the pin is not bent. If it is bent, straighten

the pin as illustrated, then plug the pin into antenna terminal.

Bent pin

Cable Plug

(Straight pin)

(Needs to be straightened)

VHF/UHF Antenna

(Not supplied)

Rod Antenna

(Not supplied)

ANT.

AUDIO OUT DIGITAL OUT

COAXIAL

[Fig. 4]

NOTE:

The connection of an indoor antenna may not always give acceptable TV reception.

VHF/UHF SEPARATE ANTENNAS

In some areas it will be necessary to use an outdoor antenna.

VHF Antenna (Not supplied)

VHF/UHF

Combiner

(Not

supplied)

UHF Antenna

(Not supplied)

ANT.

AUDIO OUT DIGITAL OUT

COAXIAL

ANT.

Flat twin-lead cable

[Fig. 5]

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

CABLE WITHOUT CONVERTER/

DESCRAMBLER BOX

Use this connection if your cable system connects directly to your TV/DVD without a converter box.

From Cable System

75-ohm Coaxial

Cable (Not

supplied)

ANT.

AUDIO OUT DIGITAL OUT

COAXIAL

[Fig. 6]

CABLE WITH CONVERTER/

DESCRAMBLER BOX OR SATELLITE BOX

If your cable service supplies you with a converter box or if you use a satellite system, you can use the basic

connection shown here.

Satellite Box or

Cable Box (Not supplied)

OUT

From Cable System

or Satellite Dish

75-ohm Coaxial

Cable

(Not supplied)

ANT.

AUDIO OUT DIGITAL OUT

COAXIAL

[Fig. 7]

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC

that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be

connected to the grounding system of the building as close to the point of cable entry as practical.

–

_{Download from Www.Somanuals.co}1_m1_{. All Manuals Search And Download.}

0C28

INSTALLING THE BATTERIES

1)Open the battery compartment cover by pressing the cover on the remote unit in the direction of the arrow.

2)Insert 2 "AA" penlight batteries into the battery compartment in the direction indicated by the polarity (+/-)

markings.

3)Replace the cover.

CONNECTING TO EXTERNAL INPUT JACKS

When you watch a program recorded on an another source (VCR or video camera), use the audio/video input

jacks on the front of the TV/DVD.

Connect the audio/video output jacks of another source to the AUDIO L/R and VIDEO jacks of this TV/DVD.

Then press the SELECT button until "VIDEO" appears on the screen.

NOTE:

When you connect a monaural VCR (another source) to this TV/DVD, connect the Audio output jack of the

monaural VCR (another source) to the AUDIO L jack of this TV/DVD. The audio will output in both L and

R channel equally.

•

To the audio

output jacks

[Another source]

Audio/Video

coaxial cable

(not supplied)

VIDEO L-AUDIO-R

etc.

To the video

output jack

[Fig. 8]

[Front of the TV/DVD]

Antenna/Cable Connections Continued on the Next Page.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

CONNECTING TO A STEREO SYSTEM (for DVD)

ANT.

AUDIO OUT DIGITAL OUT

COAXIAL

Stereo system

To Right (red) and Left (white)

AUDIO OUT jacks

(only DVD AUDIO OUT)

To ANALOG AUDIO INPUT jacks

[Fig. 9]

NOTES:

Be sure to turn off the power to all components in the system before connecting another component.

Refer to the Owner's Manuals for your, stereo system and any other components to be connected to the

TV/DVD.

•

The AUDIO output jacks (red/white) on the rear panel serve to give out DVD sound, not TV sound and

external input sound.

•

CONNECTING TO AN AMPLIFIER EQUIPPED WITH DIGITAL

INPUT JACKS, MD DECK OR DAT DECK (for DVD)

Use an audio coaxial digital cable (commercially available) for the audio connections.

ANT.

AUDIO OUT DIGITAL OUT

COAXIAL

To DIGITAL AUDIO OUT

(PCM/BITSTREAM)

COAXIAL jack

Amplifier equipped with digital

input jacks, MD deck,

DAT deck, etc.

(only DVD AUDIO OUT)

To COAXIAL DIGITAL

AUDIO INPUT jack

[Fig. 10]

NOTES:

The audio source on a disc in a 5.1 channel Dolby Digital surround format cannot be recorded as digital

sound by an MD or DAT deck.

•

Be sure to turn off the power to all components in the system before connecting another component.

Refer to the Owner's Manuals for the components to be connected to the TV/DVD.

Set DOLBY DIGITAL and DTS to OFF for audio output in the setup mode. Playing a TV/DVD using

incorrect settings may generate noise distortion, and may also damage the speakers.

When DOLBY DIGITAL is set to OFF and VIRTUAL 3D to ON for audio output in the setup mode and

you select the audio source in a 5.1 channel Dolby Digital surround format, the audio will be muted.

•

–

_{Download from Www.Somanuals.co}1_m3_{. All Manuals Search And Download.}

0C28

CONNECTING TO A DOLBY DIGITAL DECODER

OR DTS DECODER (for DVD)

If using this TV/DVD to play back a TV/DVD in a 5.1 channel Dolby Digital surround or DTS surround for-

mat, the TV/DVD outputs a Dolby Digital or DTS data stream from its COAXIAL digital audio out jack. By

hooking the player up to a Dolby Digital or DTS decoder, you can enjoy a more convincing, realistic ambi-

ence with powerful and high-quality surround sound of a professional standard such as can be heard in movie

theaters.

Use audio coaxial digital cables (commercially available) for the audio connections.

Center

speaker

Front speaker

(left)

ANT.

Front speaker

(right)

AUDIO OUT DIGITAL OUT

COAXIAL

Dolby Digital

or DTS decoder

To DIGITAL AUDIO OUT

(PCM/BITSTREAM)

COAXIAL jack

To COAXIAL DIGITAL

AUDIO INPUT jack

Subwoofer

Surround

speaker

(left)

Surround

speaker

(right)

[Fig. 11]

NOTES:

Be sure to turn off the power to all components in the system before connecting another component.

Refer to the Owner's Manuals for the components to be connected to the TV/DVD.

If connected to a Dolby Digital decoder, set DOLBY DIGITAL to ON for audio output in the setup mode.

If connected to a DTS decoder, set DTS to ON for audio output in the setup mode.

Unless connected to a Dolby Digital decoder or a DTS decoder, set DOLBY DIGITAL and DTS to OFF for

audio output in the setup mode. Playing a TV/DVD using incorrect settings may generate noise distortion,

and may also damage the speakers.

•

When DOLBY DIGITAL is set to OFF and VIRTUAL 3D to ON for audio output in the setup mode and

you select the audio source in a 5.1 channel Dolby Digital surround format, the audio will be muted.

•

Manufactured under license from Dolby

Laboratories. “Dolby” and the double-D

symbol are trademarks of Dolby

Laboratories. Confidential Unpublished

“DTS” and “DTS Digital Out” are trademarks

of Digital Theater Systems, Inc.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

TV SECTION

SET UP FOR USE

Getting started

CHANNEL SET

LANGUAGE [ENGLISH]

ESPAÑOL

FRANÇAIS

V-CHIP SET UP

CAPTION [OFF]

Press the Arrow K or L button to

point to "CHANNEL SET". Then,

press the Arrow B button.

Connect the power cord to a standard AC outlet.

NOTE: If some digits appear in the corner of the

screen, press the POWER button without unplugging

the power cord.

Press the Arrow K or L button to

point to "AUTO MEMO". Then,

press the Arrow B button.

ADD/DELETE

AUTO MEMO

Press the POWER button to turn on the TV/DVD.

The tuner scans and memorizes all

active channels in your area.

Press the SELECT button on the remote control until

channel number or "TV" appears on the screen.

Then press the TV button.

The TV distinguishes between standard TV chan-

nels and cable channels.

•

When AUTO MEMO action is completed, the low-

est memorized channel reappears on the screen.

When you press the Arrow K or L button after

selecting AUTO MEMO, the tuner will stop at the

memorized channels only.

LANGUAGE SELECTION

If you want to change the language of the on-screen

menu, follow the procedure below.

The TV/VCR may memorize TV channels as

CATV channels if reception conditions are poor. If

this happens, try the AUTO MEMO action again

when reception conditions are better.

•

CHANNEL SET

LANGUAGE [ENGLISH]

Press the SETUP button so that the

ESPAÑOL

FRANÇAIS

setup display appears on the TV

V-CHIP SET UP

CAPTION [OFF]

screen.

[ADD/DELETE FUNCTION]

1)Press the SETUP button so that the setup display

appears on the TV screen.

CHANNEL SET

LANGUAGE [ENGLISH]

ESPAÑOL

FRANÇAIS

V-CHIP SET UP

CAPTION [OFF]

LANGUAGE [ENGLISH]

2)Press the Arrow K or L button

ESPAÑOL

Press the Arrow K or L button to

point to "LANGUAGE".

FRANÇAIS

V-CHIP SET UP

CAPTION [OFF]

to point to "CHANNEL SET".

Then, press the Arrow B button.

3)Press the Arrow K or L button

to point to "ADD/DELETE".

Then press the Arrow B button.

ADD/DELETE

AUTO MEMO

4)Use the Arrow K or L button to

select the channel you wish to

put into memory or to erase from memory.

NOTE: The display will return to the screen in

about 10 seconds. Perform "ADD/DELETE" func-

tion while this display appears on the screen.

Select "ENGLISH", "ESPAÑOL" = Spanish or

"FRANÇAIS" = French by using the Arrow B or s

button.

Press the SETUP button to exit the setup.

NOTE: An on-screen display language must be

selected each for the TV mode and DVD mode.

Press the Arrow B or s button to light up the

channel number in LIGHT BLUE if you wish to

add the channel into memory.

•

Press the Arrow B or s button to light up the

channel number in LIGHT RED if you wish to

erase the channel from memory.

CHANNEL PRESETTING

To preset a channel or to change a preset channel,

follow the procedure below.

•

5)Press the SETUP button to exit the setup.

CHANNEL SET

LANGUAGE [ENGLISH]

ESPAÑOL

FRANÇAIS

V-CHIP SET UP

CAPTION [OFF]

Press the SETUP button so that the

setup display appears on the TV

screen.

–

_{Download from Www.Somanuals.co}1_m5_{. All Manuals Search And Download.}

0C28

OPERATIONS

DEGAUSSING

WATCHING A TV PROGRAM

Magnetism from nearby appliances might affect the

color of the TV picture.

If this happens, move this unit away from the appli-

ance. If the color is still not correct, disconnect power

cord from AC outlet then reconnect it after 30 minutes.

Select the desired channel with the CH(annel) K or

L button.

Adjust the volume to the desired listening level using

the VOL(ume) K or L button.

CLOSED CAPTION

This TV can receive C1 and C2 of Caption and Text.

CAPTION MODE

1)Characters can be displayed on the TV screen when

the received broadcast signal contains the Caption

Signals.

Adjust picture controls for a natural looking image.

(See "PICTURE ADJUSTMENT".)

Note: Suppose that the TV/DVD is shut off or in any

2)Paint-on mode: Displays input characters on the

screen immediately.

Pop-on mode: Once characters are stored in mem-

ory, it is displayed all at once.

other mode than TV. Press the CHANNEL K or L

button on the TV/DVD, and the TV/DVD will be in

the TV mode to watch television.

Roll-up mode: Displays the characters continuous-

ly by scrolling (max. 4 lines)

SELECTING THE SLEEP TIMER

NOTE: If the CAPTION C1 or C2 is selected but the

caption signal is not included, characters will not be

displayed.

The sleep timer function enables you to shut off the

power without pressing the POWER button after a

desired time period.

TEXT MODE

1)Displays the text on the screen by scrolling (max. 7

lines)

Press the SLEEP button on the remote control.

2)If the received broadcast signal does not contain

the caption or text signal, no change will occur.

NOTES:

You may change the sleep time

with pressing the SLEEP button on

1)When your TV receives a special effects playback

signal (i.e., Search, Slow, Still) from a VCR’s

video output channel (CH3 or CH4), your TV may

not display the correct caption or text.

2)Captions and texts may not match the TV voice

exactly.

3)Interference may cause the closed caption system

not to function properly.

4)The caption or text characters will not be displayed

while the setup display or function’s display is

shown.

the remote control repeatedly. The

timer is set up to 90 minutes, 10

minutes each time the SLEEP button is pushed. (The

timer display counts up and sleep timer will be dis-

played on the screen when you press the SLEEP but-

ton on remote control.)

SLEEP 10

To cancel the sleep timer:

Press the SLEEP button repeatedly until "SLEEP 0"

is displayed.

NOTES:

When you disconnect the unit from the AC outlet,

or if you have a power failure, the sleep time will

be lost.

•

When the TV mode is changed to the DVD mode,

the sleep time will be lost.

•

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

5)If you see this screen!!

Select the feature you wish to adjust with the Arrow

K or L button and adjust it with the Arrow B or s

button.

If your TV displays a black box on the screen, this

means that your TV is set to TEXT mode. To clear

screen, select CAPTION C1, C2 or CAPTION

[OFF].

GAME MODE

Set to the most suitable position for TV GAME.

[B] : ON

[s] : OFF

BRIGHT

CLOSED CAPTION SELECTION

You may view specially labeled (cc) TV programs,

movies, news, prerecorded tapes, etc. with either a

dialogue caption or text display added to the pro-

gram.

Adjust until the whitest parts of the picture are as

bright as you prefer.

[B] : increase brightness

[s] : decrease brightness

CONTRAST

Adjust to increase or decrease contrast.

[B] : increase contrast

[s] : decrease contrast

COLOR

Press the SETUP button so that the setup display

appears on the TV screen.

Adjust to be brilliant or pale color.

[B] : be brilliant color

[s] : be pale color

Press the Arrow K or L button to point to "CAP-

TINT

TION".

Adjust to obtain natural skin tones.

[B] : greenish tone

[s] : reddish tone

Press the Arrow B or s button to select the mode

you wish.

NOTES:

In the above steps, the picture adjustment display

•

will disappear from the TV screen after about 10

seconds unless you press any buttons, even though

you may not be finished. Press the SETUP and

Arrow B button so that "PICTURE" mode is

selected. Then, press the Arrow K or L button

repeatedly until the display returns to the screen.

When done, press the SETUP button to exit the

setup.

B or s

: Press the Arrow

button.

If you adjust the other Picture control after you set

•

CHANNEL SET

LANGUAGE [ENGLISH]

ESPAÑOL

FRANÇAIS

V-CHIP SET UP

CAPTION [OFF]

CHANNEL SET

LANGUAGE [ENGLISH]

ESPAÑOL

FRANÇAIS

V-CHIP SET UP

CAPTION [ C1]

the Game mode to [ON], the Game mode is set to

[OFF] automatically. If you want to set the Game

mode, reset it to [ON].

: Press the Arrow L or L button.

CHANNEL SET

LANGUAGE [ENGLISH]

ESPAÑOL

FRANÇAIS

V-CHIP SET UP

CAPTION [ C2]

[

]

[

]

[

]

[

]

GAME MODE

BRIGHT

CONTRAST

COLOR

OFF

CHANNEL SET

LANGUAGE [ENGLISH]

ESPAÑOL

CHANNEL SET

LANGUAGE [ENGLISH]

ESPAÑOL

FRANÇAIS

V-CHIP SET UP

CAPTION [ T2]

V-CHIP SET UP

CAPTION [ T1]

PICTURE ADJUSTMENT

[

]

[

]

TINT

Press the PICTURE button.

–

_{Download from Www.Somanuals.co}1_m7_{. All Manuals Search And Download.}

0C28

V-CHIP SET UP

• G:

General Audience

V-CHIP enables parents to prevent their children

from watching inappropriate material on TV.

V-CHIP reads the ratings for programming (except

for news and sports programs, unedited movies on

premium cable channels, and Emergency Broadcast

System signals), then denies access to programming

if the program's rating meets the limitations you

select. In this case, "PROTECTED PROGRAM by

..." message appears on the TV screen. You can

watch the protected program by entering access code

(default 0000).

• PG:

• PG-13:

• R:

Parental Guidance suggested.

Unsuitable for children under 13

Restricted; under 17 requires

accompanying parent or adult

guardian

No one under 17 admitted

Mature audience only

• NC-17:

• X:

When you select the rating category and turn it

[BLOCK], the higher rating will turn [BLOCK]

automatically. Also, the lower rating will turn

[VIEW] automatically.

•

To block ratings, follow the steps below.

When you turn "G" to [BLOCK] or [VIEW], the

all ratings will turn to [BLOCK] or [VIEW] auto-

matically.

When you turn "X" to [VIEW], the all ratings will

turn to [VIEW] automatically.

•

Programming may be rated by the Motion Picture

•

Association of America (MPAA) or according to

the Television Parental Guidelines. In order to

block any inappropriate programming, set your

limits in both places (MPAA RATING and TV

RATING).

You cannot access the menu when the "PROTECT-

•

ED PROGRAM by ..." message appears. In this

case, change to the unblocked channel, then press

the SETUP button.

Press the SETUP button to exit the setup.

[TV RATING SET UP]

[MPAA RATING SET UP]

Press the SETUP button so that the setup display

appears on the TV screen.

Press the SETUP button so that the setup display

appears on the TV screen.

CHANNEL SET

LANGUAGE [ENGLISH]

Press the Arrow K or L button to

point to "V-CHIP SET UP". Then,

press the Arrow B button.

ESPAÑOL

FRANÇAIS

CHANNEL SET

LANGUAGE [ENGLISH]

ESPAÑOL

FRANÇAIS

V-CHIP SET UP

CAPTION [OFF]

V-CHIP SET UP

Press the Arrow K or L button to

point to "V-CHIP SET UP". Then,

press the Arrow B button.

CAPTION [OFF]

ACCESS CODE

Use the number buttons to enter 4-

digit access code. The default code

is 0000.

ACCESS CODE

Use the number buttons to enter 4-

digit access code. The default code

is 0000.

TV RATING

MPAA RATING

CHANGE CODE

Press the Arrow K or L button to

point to "TV RATING". Then,

press the Arrow B button.

TV RATING

MPAA RATING

CHANGE CODE

Press the Arrow K or L button to

point to "MPAA RATING". Then,

press the Arrow B button.

TV-Y

TV-Y7

TV-G

TV-PG (

TV-14

TV-MA (

[VIEW]

) [VIEW]

[VIEW]

) [VIEW]

Press the Arrow K or L button to

point to your desired item. Then,

press the Arrow B button to select

[BLOCK] or [VIEW].

(

[VIEW]

[BLOCK]

PG-13

NC-17

Press the Arrow K or L button to

point to your desired item.

Then, press the Arrow B button to

select [BLOCK] or [VIEW].

(

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

[CHANGE ACCESS CODE]

To change access code, follow the steps.

• TV-Y:

• TV-Y7:

Appropriate for all children

Appropriate for children seven and

older

• TV-G:

General Audience

Press the SETUP button so that the setup display

appears on the TV screen.

• TV-PG:

• TV-14:

• TV-MA:

Parental Guidance suggested.

Unsuitable for children under 14

Mature audience only

CHANNEL SET

LANGUAGE [ENGLISH]

ESPAÑOL

FRANÇAIS

V-CHIP SET UP

CAPTION [OFF]

When you select the rating category and turn it

[BLOCK], the higher rating will turn [BLOCK]

automatically. Also, the lower rating will turn

[VIEW] automatically.

Press the Arrow K or L button to

point to "V-CHIP SET UP". Then,

press the Arrow B button.

•

When you turn "TV-Y" to [BLOCK] or [VIEW],

the all ratings will turn to [BLOCK] or [VIEW]

automatically.

When you turn "TV-MA" to [VIEW], the all rat-

ings will turn to [VIEW] automatically.

•

ACCESS CODE

Use the number buttons to enter 4-

digit access code. The default code

is 0000.

When you select TV-Y7, TV-PG, TV-14, or TV-MA

and you press the Arrow B button, the sub-ratings

will appear on the TV screen.

If you select the rating category (example: TV-PG)

and turn it [BLOCK] or [VIEW], the sub-ratings

(example: V for Violence) will turn [BLOCK] or

[VIEW] automatically.

TV RATING

MPAA RATING

CHANGE CODE

Press the Arrow K or L button to

point to "CHANGE CODE". Then,

press the Arrow B button.

You can set the sub-ratings to [BLOCK] or [VIEW]

individually when the rating category is set to

[BLOCK]. To set the sub-ratings individually, follow

the steps below.

Use the number buttons to enter

your desired access code in the

NEW CODE space. Then enter the

same code in the CONFIRM

CODE space. V-CHIP SET UP

screen appear on the screen.

NEW CODE

TV-Y7

[BLOCK]

When you select [TV-Y7]:

Press the Arrow K or L button

to select "FV" (Fantasy

•

CONFIRM CODE

[BLOCK]

Violence). Then, press the Arrow

B button to select [BLOCK] or

[VIEW].

When you select [TV-PG],

[TV-14] or [TV-MA]:

NEW CODE

TV-PG

[BLOCK]

If you enter wrong code, repeat

x x x x

•

step 5, making sure you enter

the same new code exactly in

the confirm code space.

[BLOCK]

CONFIRM CODE

•

Press the Arrow K or L button

to select "D"(Suggestive

Dialog), "L"(Coarse Language),

"S"(Sexual Situation), or

"V"(Violence). Then, press the

Arrow B button to select [BLOCK] or [VIEW].

NOTE: When you select [TV-MA], "D" does not

appear on the TV screen.

TV-Y

TV-Y7

TV-G

TV-PG (DLSV)[BLOCK]

TV-14 (DLSV)[BLOCK]

TV-MA ( LSV)[BLOCK]

[VIEW]

)[VIEW]

[BLOCK]

(

Press the SETUP button to exit the setup.

Note:

If you unplug the power code or power failure

•

occures, the changed access code will be lost and

will return to default (0000). Change your access

code again as necessary.

The sub-ratings which set to [BLOCK] appears

next to the rating category in the TV RATING

menu.

•

Press the SETUP button to exit the setup.

–

_{Download from Www.Somanuals.co}1_m9_{. All Manuals Search And Download.}

0C28

DVD SECTION

ABOUT THE DISCS

Photo CD

PLAYABLE DISCS

(Never play back, otherwise malfunction may

result.)

The following discs can be played back on this DVD

player.

Video CD

(Never play back, otherwise malfunction may

result.)

Maximum

Playback Time

Disc Type

Logo

Contents Disc Size

Any other discs without compatibility indications

Approx. 4 h

(single-sided)

Approx. 8 h

12 cm

Sound

and

Pictures

(double-sided)

DVD

Video

DISC TYPES

Approx. 80 min

(single-sided)

Approx. 160 min

(double-sided)

[

]

DVD

8 cm

Data on a DVD is divided into sections called "titles", and

then into subsections called "chapters", each of which is

given a title or chapter number. Playback conditions are

preset on some DVD video discs, and these playback con-

ditions take priority over user operations on this player. If

a function you selected do not run as desired, refer to the

manual accompanying the disc.

12 cm

74 min

Audio

Sound

8 cm

20 min

(singles)

This player conforms to the NTSC color system. You can-

not play discs recorded in other color systems such as

PAL or SECAM.

Example

¡Some discs include region codes as shown below.

Title 1

Title 2

Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1 Chapter 2

¡The number inside the symbol refers to a region of the

world, and a disc encoded in a specific region format

can only be played back on DVD players with the same

region code.

[

]

AUDIO CD

Data on an audio CD is divided into sections called

“tracks”, each of which is given a track number.

The following discs cannot be played back on this

DVD player.

Example

Track 1

Track 2

Track 3

Track 4

Track 5

Track 6

DVD with region codes other than 1 or ALL.

DVD-ROM

DVD-RAM (Never play back, otherwise mal-

function may result.)

CD-ROM

VSD

CDV (Only plays back the audio part.)

CD-G (Only plays back the sound.)

CD-R

(Never play back, otherwise malfunction may

result.)

CD-I

(Never play back, otherwise malfunction may

result.)

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

PLAYING A DISC

PLAYING A DVD VIDEO

Notes

OR AN AUDIO CD

¡When the DVD mode has been switched to the TV

mode, the DVD mode shut down first and then TV

picture and sound appears in about 4 seconds.

Similarly, when the POWER button is pressed off in

the DVD mode, this mode shut down first and then

the set’s power is turned off.

DVD

Getting started

Turn on the power of the TV, amplifier and any other

components which are connected to the DVD player.

(Change the input system to suit the DVD player, and ¡A “prohibited icon” may appear at

check that the sound volume is correct.)

the top-right on the TV screen

during operation, warning that a

prohibited operation has been

encountered by the DVD player

or the disc.

Press the POWER button.

¡The power will turn on.

Press the OPEN/CLOSE button.

¡If a disc is dirty or has scratches, the pictures may

appear distorted and the playback operation may

stop. In such cases, clean the disc and unplug the

power cord and then plug it again before resuming

playback.

¡The disc loading tray will open.

Place a disc into the tray.

¡Make sure the disc is sitting properly in the correct

recess, with the label side up.

¡With DVDs that use some titles for playback

program signals, playback may start from the second

title, or it may skip these titles.

USING THE DVD MENUS

DVD

Press the PLAY button.

Some DVDs contain their own menus, such as a

guidance menu which describes the contents of the

disc or a selection menu for sound, language and other

customized settings.

¡The tray will close automatically, and playback will

then start from the first chapter or track of the disc.

You need to press the PLAY button only when the

tray has been closed by pressing the OPEN/CLOSE

button.

Press the DISC MENU button.

¡When you play back the DVD which a title menu is

recorded, the menu may appear on the screen. In this

case, refer to “USING THE TITLE MENU”.

¡The DVD menu will appear.

Select the desired title.

¡Press the arrow buttons (L/K/B/s) to change the

setting, and then press the ENTER button.

Press the STOP button to stop play.

Playback will start from the selected title.

–

_{Download from Www.Somanuals.co}2_m1_{. All Manuals Search And Download.}

0C28

RESUMING PLAYBACK FROM

THE POINT WHERE

USING THE TITLE MENU

PLAYBACK STOPPED

DVD

With a DVD containing a title menu, you can select

desired titles from the menu.

Press the STOP button during playback.

Press the TITLE button.

¡Playback will stop, and then

appear the resuming message at

the center.

¡The title menu will appear.

Press 'PLAY' to play from here

To play beginning, press 'STOP' first

and the 'PLAY'.

Select the desired title.

¡Press the arrow buttons (L/K/B/s) to change the

setting, and then press the ENTER button.

Press the PLAY button. Playback will start

from the point where the previous playback

session was stopped.

Play B

CALLING UP A MENU SCREEN

DURING PLAYBACK

Notes

For DVDs

¡Resuming playback is not available with some discs.

¡Press the DISC MENU button to call up the DVD

menu.

¡If you switch to the TV mode during DVD playback,

the resuming

¡Press the TITLE button to call up the title menu.

¡It is possible to switch from the DVD play mode to

the TV mode. Even if the power is turned off, the

resume function enables to playback on from the

previously interrupted point. But note that the

Marker commands are not saved.

Note

¡Contents of menus and corresponding menu

operations may vary between discs. Refer to the

manual accompanying the disc for details.

¡The resume function can be reset by pressing the

STOP button twice or by opening the disc loading

tray.

PAUSING PLAYBACK OR

DISPLAYING A STILL PICTURE

DVD

STEPPING THROUGH FRAMES

Press the PAUSE button during playback.

DVD

¡Playback will pause, with sound

Pause F

muted.

Press the PAUSE button while playback is

paused.

Pause F

¡The next picture frame is dis-

played with sound muted each

time the button is pressed.

Press the PLAY button to resume playback.

Play B

Press the PLAY button to resume playback.

Play B

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

FAST FORWARD/REVERSE

Press the numeric buttons to enter the

desired track number.

DVD

The selected track will be located, and playback will start.

You can also press the SEARCH MODE button, use

the numeric buttons to enter the track number, when

the track number is entered in the

Press the FWD g or REV h button dur-

ing playback.

entry box, playback of the desired

Track: __ / 26

¡For DVDs, pressing the FWD g or REV h

button cycles the playback speed in three steps.

track will start automatically.

¡For audio CDs, the playback speed is ×16 fixed.

REV

Button

FWD D

Button

Ex2

Dx2

TRICKS WITH THE SKIP BUTTONS (H, G)

Ex8

Dx8

If the SKIP button G is pressed during playback or

while playback is paused, the current track is

skipped and the next track is played. When the SKIP

button H is pressed once, the top of the current

track is located for replaying. When the SKIP button

H is pressed again while Within 2-second

playback, the previous track is located.

Ex32

Press the PLAY button to return to normal

playback speed.

SLOW MOTION

STARTING FROM A DESIRED

TIME COUNT

DVD

Press the FWD g button while playback is

paused. (Sound remains muted.)

Press the SEARCH MODE button.

¡Slow motion mode will be activated.

¡Pressing the FWD g button cycles the playback ¡Press the button twice for DVDs

Time _:__:__

Total Time 1:29:00

speed in three steps. Select an appropriate speed

or two times for audio CDs.

while referring to the speed indication on the screen.

FWD D

Button

×1/16

Press the numeric buttons to set the desired

×1/8

time count.

Time _:__:__

Total Time 1:29:00

×1/2

¡Example: 1 hour, 23 minutes and

30 seconds

1 → 2 → 3 → 3 → 0

Press the PLAY button to return to normal

playback speed.

Notes

¡In the case of DVD, Time Search in Title is effec-

tive. (But Time Search in Chapter is ineffective.)

¡Slow playback is not available with audio CDs.

¡In the case of CD, Time Search in Track is effective.

(But Time Search in the entire disc is ineffective.)

¡The reverse of slow playback is not available.

¡Playback from a desired time count is not available

with some discs.

STARTING FROM A DESIRED

TRACK

¡Specific time playback is not available with some

discs or if the unit is in stop mode.

–

_{Download from Www.Somanuals.co}2_m3_{. All Manuals Search And Download.}

0C28

PLAYING FROM A DESIRED

TITLE OR CHAPTER

REPEAT

DVD

Press the REPEAT button.

You can also press the SEARCH MODE button, use

the numeric buttons to enter the chapter number.

For DVDs

¡A single title or chapter is played back repeatedly.

Perform the title search and the

chapter search after setting them on

the same screen at the same time.

Changeover by K/L buttons.

¡Pressing the REPEAT button cycles the display on

the screen as follows.

Title 1 / 4

Chapter:__ / 17

Repeat

[Title]

The current Title is

played back repeatedly.

Repeat

[Chapter]

The current Chapter is

played back repeatedly.

Note

Title 1 / 4

Chapter:__ / 17

Repeat

[Off]

No repeat playback.

¡Playback from a desired title or

chapter is not available with some

DVDs.

RANDOM (Audio CD)

For audio CDs

¡The whole disc or a single track is played back

repeatedly.

¡Pressing the REPEAT button cycles the display on

the screen through All, Repeat Track and Off.

Press the MODE button in stop mode.

¡The program setting menu screen will appear.

Repeat

[All]

The whole Disc is

played back repeatedly.

Press the MODE button again.

Audio CD

Random

Repeat

[Track]

The current Track is

played back repeatedly.

Start

PLAY Exit

MODE

Repeat

No repeat playback.

[Off]

Press the PLAY button. Random playback

will then start.

If the REPEAT button is pressed once dur-

ing program/random playback, the pro-

gram/random playback is performed

repeatedly.

Note

¡Program playback is not available during random

playback.

If the REPEAT button is pressed again, the

current track is played back repeatedly.

Notes

¡Repeat playback is not available with some discs.

¡The REPEAT setting will be cleared when moving

to other title, chapter or track.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

A-B REPEAT

PROGRAM (Audio CD)

DVD

You can define a section to be played back repeatedly.

Press the MODE button in stop mode.

Audio CD

¡The program screen will appear.

Program

Press the A-B REPEAT button during playback.

Total

[Track]

– –

[Time]

0:00:00

¡The starting point (A) will then be

Repeat

[ A -

Track

00 / 15

]

Start

Random

PLAY Delete

MODE Exit

CLEAR

RETURN

selected.

Press the numeric buttons to enter the

desired track numbers.

Audio CD

Program

02 05 07 14 01 09 13 10 03 11

08 04

¡The total playback time for the

selected tracks will appear on the

TOTAL line.

Total

[Track]

Press the A-B REPEAT button again at the

end point (B) of the desired section.

[Time]

0:47:29

Track

04 / 15

Start

Random

PLAY Delete

MODE Exit

CLEAR

RETURN

¡The selected section will be

Repeat

[ A - B ]

played back repeatedly.

Press the PLAY button.

¡Playback will start in the programmed order.

¡While the program is being played back, the STOP

button works as follows.

To exit A-B repeat playback, press the A-B

REPEAT button and set it to OFF.

¡Press the STOP button once and then the PLAY

button again, playback will restart from the point

where the STOP button was pressed. (Program

continued)

Repeat

[ off ]

¡Press the STOP button twice and then the PLAY

button again, playback will restart from the first tune

in the program in the usual way. (Program

continued)

Notes

¡With DVDs, the A-B repeat section can be set only

within the current title.

¡Press the STOP button three times and then the

PLAY button again, playback will restart from the

track in the usual way. (Program cleared)

¡With audio CDs, the A-B repeat section can be set

within the current track.

¡A-B repeat is not available with some scenes in

DVD.

Notes

¡To cancel the A point which was set, press RETURN

¡Adding programs is not possible during program

playback. You must stop the current playback before

such operations can be carried out.

button.

¡Press the CLEAR button to cancel a program. The

most recently entered program will then be deleted.

¡Numbers which exceed the number of tracks on the

disc in the tray are not accepted.

¡Playback from a desired track and random playback

are not available during program playback.

¡Program settings are cleared when the power is

turned off or the disc loading tray is opened.

¡If the track no. is once set in the program, the setting

cannot be changed.

–

_{Download from Www.Somanuals.co}2_m5_{. All Manuals Search And Download.}

0C28

SETTINGS

CHANGING THE AUDIO

LANGUAGE OR SOUND MODE

ZOOM PLAYBACK

(enlargement onscreen)

DVD

Images can be enlarged four times on the screen to The DVD player has a function which allows you to

your taste.

select the desired audio language and sound mode.

Press the ZOOM button during playback.

For DVDs

¡An image will be enlarged at the center of the Press the AUDIO button during playback, and then

screen.

press the AUDIO button to select the desired audio

language.

¡Press the ZOOM button again, and the image will be

back to the previous size.

¡The audio language can be changed if multiple

languages are recorded on the DVD being played.

Zoom [on]

Audio 1 , English/8

Audio 2 , French/8

Audio 8 , Japanese/8

When the cursor (K/L/s/ B) button is pressed

during zoom play, the part to be zoomed moves.

¡The zooming frame can be moved from the center

.... 4 steps to the right. 4 steps to the left. 4 steps to

the top. 4 steps to the bottom.

Bonjour

HELLO

Notes

¡Pressing the Audio button may not work on some

DVDs with multiple audio languages (e.g. DVDs

which allow audio language setting on the disc

menu). Operation varies between discs, so refer to

the manual accompanying the disc.

¡If a desired language is not shown after pressing the

Audio button several times, the disc does not have

an audio source in that language.

¡The audio language resets to the one which has been

selected in the setup mode, every time the power is

turned on or discs are replaced. If that language is

not available on a disc, a language defined by the

disc is selected.

Note

¡Zooming function does not work while operation

display screen is shown.

¡The screen display will disappear after about 5

seconds.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

CHANGING THE SUBTITLE

LANGUAGE

CHANGING THE CAMERA

ANGLE (Multi-Angle Pictures)

DVD

The DVD player has a function which allows you to The DVD player has a function which allows you to

select the desired language for subtitles.

select the desired camera angle.

Press the SUBTITLE button during playback, and

then press the SUBTITLE button to select the

desired subtitle language.

Press the ANGLE button during playback.

¡If the disc contains sequences recorded from differ-

ent camera angles, the angle icon ( ) will appear

¡The subtitle language can be changed if the subtitles

are recorded in multiple languages on the DVD

being played.

at the top-right of the screen. You can change the

camera angle when the icon appears on the screen.

¡The camera angle cannot be changed if the disc does

not contain sequences recorded from different

camera angles.

¡The subtitle language cannot be changed if the

subtitles are recorded in a single language on the

DVD being played.

Subtitle 1 , English/8

Subtitle 1

Press the ANGLE button while the angle

number is shown on the screen.

Subtitle 2 , French/8

Subtitle 2

Angle 1 / 8

Angle 1

Angle 2 / 8

Subtitle Off

Angle 2

No subtitles

Angle 8 / 8

Angle 8

Bonjour

HELLO

Note

¡The screen display will disappear after about 5

seconds.

¡Pressing the SUBTITLE button cycles the subtitle

language from SUBTITLE 1, SUBTITLE 2 and all

the languages recorded through to off.

Notes

¡Some discs allow subtitle language setting on the

disc menu. (Operation varies between discs, so refer

to the manual accompanying the disc.)

¡If the desired language is not shown after pressing

the SUBTITLE button several times, the disc does

not have subtitles in that language.

¡The subtitle language resets to the one which has

been selected in the setup mode, every time the

power is turned on or discs are replaced. If that

language is not available on a disc, a language

defined by the disc is selected.

¡It may take time to display the subtitles in the

selected language.

¡The screen display will disappear after about 5

seconds.

¡When “Subtitle Not Available” appears onscreen, it

means no subtitle is recorded on the scene.

–

_{Download from Www.Somanuals.co}2_m7_{. All Manuals Search And Download.}

0C28

CHANGING THE ON-SCREEN

DISPLAY

For DVDs

Kind of disc in playbacking

DVD

Play

Picture in play back

Current playback status

Current repeat status

Current title number

Current chapter number

Repeat

[Chapter]

DVD

Title

Chapter

Time

0:17:52

-1:38:46

Bit Rate

You can check the information about the disc by

pressing the DISPLAY button on the remote control.

• Chapter

Title

18 / 30

1 /

Time

Audio

1:56:38

1.English / 4

Elapsed time of the current title and

Remaining time of the current title.

Info. Window

For audio CDs and DVDs

Playback Setup Window

Playback Setup Window (DVD)

Press the DISPLAY button, the display appears on the

screen.

ITEM

Chapter

DISPLAY CONTENTS

Current chapter number / the number of

total chapters

Current title number / the number of total

titles

Title

For the selecting the item of the Playback Setup

Time

Audio

Total time of the current title

Window, press the K L

then press the ENTER button.

button to select the item,

Audio No., audio language / the number

of available audio languages in the disc

Subtitle No., subtitle language / the

number of available subtitle languages in

the disc

Subtitle

Angle

For audio CDs

Off : Subtitle is not displays.

Not Available : Subtitle is not included.

Kind of disc in playbacking

Current playback status

Current repeat status

Current track number

Nomal playback

Audio CD

Play

01 02 03 04 05 06 07 08 09 10

11 12

Repeat

[Track]

Angle No. / total number of the angles

1/1 : Multi angle is not included in the

disc.

Track

Play Mode

Normal

Track

Time

Maker

2 / 12

0:05:13

...

Programedplayback

Random playback

Time

[Track]

0:01:46

-0:03:27

Place the cursor and press the ENTER

button to activate the Marker function.

Time Display Track

[Track]

Elapsed time of the current track and

Remaining time of the current track.

[All]

Elapsed time of the current disc and

Remaining time of the current disc.

[Set the marker]

Info. Window

Playback Setup Window

K L

button, position the cursor on

Using

to the marker number shown as “Not

Set”. Press the ENTER button when the

screen to be reviewed appears.

Up to 5 points can be marked.

Playback Setup Window (CD)

[Call back the marker]

ITEM

Track

DISPLAY CONTENTS

Marker

K L

button, position the cursor on

Using

to the marker number to be called back

and press the ENTER button.

Current track number / the number of

total tracks

[Clear the marker]

Time

Total time of the current track

K L

button, position the cursor on

Using

Place the cursor and press the ENTER

button to activate the Marker function.

to the marker number to be cleared and

press the CLEAR button.

[Set the marker]

To clear all markers, place the cursor on

“All Clear Markers” and press the

ENTER button.

K L

button, position the cursor on

Using

to the marker number shown as “Not

Set”. Press the ENTER button when the

screen to be reviewed appears.

SRS

TruSurround

The current setting (On/Off) is displayed.

Up to 5 points can be marked.

[Call back the marker]

Marker

K L

button, position the cursor on

Using

To exit the display (DVD and CD):

Press the RETURN button.

to the marker number to be called back

and press the ENTER button.

[Clear the marker]

In the playback Setup Window, press the RETURN button to

change the present indication to the former one.

K L

button, position the cursor on

Using

to the marker number to be cleared and

press the CLEAR button.

To clear all markers, place the cursor on

“All Clear Markers” and press the

ENTER button.

The time informations displays on the left

side of the screen (Track/All)

Time Display

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

CHANGING THE SETUP ITEMS

Note

Press the K/L buttons to select a desired

item, and then press the ENTER button.

¡When you change the setup items, press the STOP

button if you are in playback mode.

¡If Other is selected on the Audio, Subtitle or Disc

Menu setting screen, the Language Code setting

screen will appear. Press the numeric buttons to

enter the desired language code while referring to

LANGUAGE SETTINGS

Press the SETUP button.

the list on page 25.

Language Controls

Language

Display

Audio

Subtitle

Disc Menu

Player Menu

English

Language

Display

Audio

¡The setup screen appears.

Audio

Irish

Portuguese

Dutch

.......

Parental

Other

Select

Set : ENTER

Parental

Select

Set : ENTER

Cancel :

Exit : SETUP

Cancel :

Exit : SETUP

Press the K/L buttons to select Language,

and then press the ENTER button.

Press the SETUP button.

¡The setup mode will be canceled and the ordinary

screen will appear.

Language Controls

Audio

Subtitle

Disc Menu

Player Menu

English

Language

Display

Audio

Note

Parental

Select

Set : ENTER

Cancel :

Exit : SETUP

¡Language Setting for Audio and Subtitle is not avail-

able with some discs. Then use the Audio and

Subtitle button. Details are on pages 18 and 19.

Press the K/L buttons to select an item, and

then press the ENTER button.

Language Controls

Audio

Subtitle

Disc Menu

Player Menu

English

Language

Display

Audio

(Voice is played back in selected

language.)

Audio

Original

English

French

Spanish

Parental

Select

Set : ENTER

Exit : SETUP

Cancel :

Language Controls

Audio

Subtitle

Disc Menu

Player Menu

English

(Subtitles are shown in selected

language.)

Language

Display

Audio

Subtitle

Off

English

Spanish

French

Parental

Select

Set : ENTER

Cancel :

Exit : SETUP

Language Controls

Audio

Subtitle

Disc Menu

Player Menu

English

(The disc menu appears in select-

ed language.)

Language

Display

Audio

Disc Menus

Original

English

French

Spanish

Parental

Select

Set : ENTER

Cancel :

Exit : SETUP

Language Controls

Audio

Subtitle

Disc Menu

Player Menu

English

(The on-screen display appears in

selected language.)

Language

Display

Audio

Player Menu

English

Français

Español

Parental

Select

Set : ENTER

Cancel :

Exit : SETUP

–

_{Download from Www.Somanuals.co}2_m9_{. All Manuals Search And Download.}

0C28

Press the K/L buttons to select a desired

item, and then press the ENTER button.

DISPLAY SETTINGS

Press the SETUP button.

Language

¡The setup screen will appear.

Display

Audio

Press the SETUP button.

Parental

¡The setup mode will be canceled and the ordinary

Select

Set : ENTER

Cancel :

Exit : SETUP

screen will appear.

Press the K/L buttons to select Display and

then press the ENTER button.

Display Controls

TV Aspect 4:3 Pan & Scan

On Screen Info On

Panel Display Bright

Language

Display

Audio

Angle Icon

Parental

Select

Set : ENTER

Cancel :

Exit : SETUP

Press the K/L buttons to select an item, and

then press the ENTER button.

Display Controls

TV Aspect

On Screen Info On

Angle Icon On

4:3 Pan & Scan

Language

Display

Audio

(Default : 4:3 Pan & Scan)

4:3 Pan & Scan : Full height picture,

trimmed both sides

Background Color Gray

TV Aspect

4:3 Pan & Scan

4:3 Letterbox

4:3 Letter Box : Wide screen with

black bars on top and bottom

Parental

Select

Set : ENTER

Cancel :

Exit : SETUP

Notes

• Some discs do not contain pan and scan images.

• Some discs do not contain letter box images.

Display Controls

TV Aspect

On Screen Info On

Angle Icon On

Background Color Gray

4:3 Pan & Scan

On Screen Info (Default : On)

Display or not display the disc status

(Example “PLAYB”).

Language

Display

Audio

Parental

Select

Set : ENTER

Exit : SETUP

Cancel :

Display Controls

TV Aspect 4:3 Pan & Scan

On Screen Info On

Angle Icon On

Background Color Gray

Language

Display

Audio

Angle Icon (Default : On)

Display or not display the Angle icon

on the screen.

Parental

Select

Set : ENTER

Exit : SETUP

Cancel :

Display Controls

On Screen Info On

Angle Icon

Language

Display

Audio

Background Color (Default : Gray)

Select gray or blue

Background Color Gray

Auto Power Off On

Parental

Select

Set : ENTER

Cancel :

Exit : SETUP

Display Controls

On Screen Info

Angle Icon

Background Color Blue

Auto Power Off On

Language

Display

Audio

Auto Power Off (Default : On)

Set or not set to turn off after the

screen saver is started and no keys are

pressed for 30 minutes..

Parental

Select

Set : ENTER

Cancel :

Exit : SETUP

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

Audio Controls

Digital Audio Out ...

Dynamic Range On

Downmix Mode Dolby Surround

Down Sampling 48kHz

Down Sampling (Default :

48kHz)

Language

Display

Audio

AUDIO SETTINGS

Set the output for the DVD

recorded in PCM 96kHz (96kHz

or 48kHz)

Press the SETUP button.

Parental

Select

Set : ENTER

Language

Cancel :

Exit : SETUP

¡The setup screen will appear.

Display

Audio

Parental

Select

Set : ENTER

Cancel :

Exit : SETUP

Press the K/L buttons to select a desired

item, and then press the ENTER button.

Press the K/L buttons to select Audio and

then press the ENTER button.

¡If PCM, Dolby Digital or DTS MPEG is selected on

the Digital Audio Out setting screen, press the K/L

buttons again to select a further item, and then press

the ENTER button.

Audio Controls

Digital Audio Out

Dynamic Range On

...

Language

Display

Audio

Downmix Mode Dolby Surround

Down Sampling 48kHz

Parental

Select

Set : ENTER

Dolby Digital (Default : Off)

Cancel :

Exit : SETUP

Audio Controls

Digital Audio Out ...

Dynamic Range On

Downmix Mode Dolby Surround

Down Sampling 48kHz

Language

Display

Audio

On : Output by Dolby Digital.

Set to On when the unit is con-

nected to Dolby Digital Decoder.

Digital Audio Out

Dolby Digital Off

DTS

MPEG

Off

Press the K/L buttons to select an item, and

Parental

Select

Set : ENTER

Exit : SETUP

Cancel :

then press the ENTER button.

Audio Controls

Digital Audio Out ...

Dynamic Range On

Downmix Mode Dolby Surround

Digital audio out setting (Next

step)

Audio Controls

Digital Audio Out

Dynamic Range On

Downmix Mode Dolby Surround

Down Sampling 48kHz

DTS (Default : Off)

...

Language

Display

Audio

Language

Display

Audio

Down Sampling 48kHz

On : Output DTS sound

Set to On when the unit is con-

nected to DTS Decoder.

Digital Audio Out

Dolby Digital Off

Digital Audio Out

Dolby Digital Off

DTS

MPEG

Off

DTS

MPEG

Off

Parental

Select

Set : ENTER

Exit : SETUP

Parental

Select

Set : ENTER

Exit : SETUP

Cancel :

Audio Controls

Digital Audio Out ...

Dynamic Range On

Downmix Mode Dolby Surround

Down Sampling 48kHz

Audio Controls

Digital Audio Out

Dynamic Range On

Downmix Mode Dolby Surround

Down Sampling 48kHz

Dynamic Range (Default : Off)

On : Dynamic range is available

MPEG (Default : Off)

On : Output by MPEG

Off : Convert the MPEG to PCM

Set to On when the unit is con-

nected to MPEG2 Decoder.

...

Language

Display

Audio

Language

Display

Audio

Digital Audio Out

Dolby Digital Off

DTS

MPEG

Off

¡This function is for controlling

the range of sound volume. By

compressing the range of sound

volume, it is possible not only to

suppress the output of loud

sound at night and but also to

raise the volume of low sound.

Parental

SSelect

Cancel :

Set : ENTER

Select

Set : ENTER

Exit : SETUP

Cancel :

Press the SETUP button.

¡The setup mode will be canceled and the ordinary

screen will appear.

¡However, this function is effec-

tive only for the sound recorded

by Dolby Digital recording.

When the sound recorded by

Dolby Digital 5.1ch is outputted,

the sound is compressed auto-

matically even with this function

being set at “Off”.

Audio Controls

Digital Audio Out ...

Dynamic Range On

Downmix Mode Dolby Surround

Down Sampling 48kHz

Downmix Mode

Language

Display

Audio

(Default : Dolby Surround)

Dolby Surround: When the player

is connected to an audio compo-

nent that conforms to

Parental

Select

Set : ENTER

Exit : SETUP

Cancel :

Dolby Surround Pro Logic

STEREO: When the player is con-

nected to a normal audio compo-

nent

–

_{Download from Www.Somanuals.co}3_m1_{. All Manuals Search And Download.}

0C28

CONTROL LEVELS

PARENTAL LOCK

Level 8

DVD software of any grade (adult/general/children)

can be played back.

Press the SETUP button.

Language

¡The setup screen will appear.

Display

Audio

Levels 7 to 2

Only DVD software intended for general use and

children can be played back.

Parental

Select

Set : ENTER

Cancel :

Exit : SETUP

Level 1

Press the K/L buttons to select Parental,

Only DVD software intended for children can be

played back, with those intended for adult and

general use prohibited.

and then press the ENTER button.

Language

Display

Password

Enter current password...

Notes

Audio

_ _ _ _

Parental

Select

Set : ENTER

¡With some DVDs, it may be difficult to find if they

are compatible with parental lock. Be sure to check

if the parental lock function operates in the way that

you have set.

Cancel :

Exit : SETUP

Press the numeric buttons to enter the 4-

digit password, and then press the ENTER

button.

¡Record the password in case you forget it.

¡When doing this for the first time, enter any 4 digits.

That number will be used as the password from the IF YOU FORGET THE PASSWORD

second time onward.

1) Open the tray.

Parental Contorols

Parental Level

Change

7[NC-17]

¡By entering the password, you

can then change the control level

and password settings.

Language

Display

Audio

2) Press the 1, 2, 3, 4, then DISPLAY button on the

remote control. the default setup screen will appear.

Then, press the ENTER button.

Parental

Select

Set : ENTER

Cancel :

Exit : SETUP

3) Disconnect the power once and reconnect, then

proceed the step 1 to 4 of the PARENTAL LOCK

again.

Press the K/L buttons to select an item, and

Note: If you proceed the above steps, ALL the

settings of the DVD player will be cleared. To use

the DVD player under the previous settings, set

each setting item all over again.

then press the ENTER button.

When Parental Level is selected

¡Press the K/L buttons to select an item from 8 to 1

and then press the ENTER button.

¡When Change is selected, press the numeric buttons

to enter the four digits password. Then press the

ENTER button.

Parental Contorols

Parental Level

Change

7[NC-17]

Language

Display

Audio

Parental Level

4 [PG-13]

3 [PG]

Parental

Select

Set : ENTER

Cancel :

Exit : SETUP

Parental Contorols

Parental Level

Change

7[NC-17]

Language

Display

Audio

Password

Enter current password

_ _ _ _

Parental

Select

Set : ENTER

Cancel :

Exit : SETUP

Press the RETURN button.

¡The setup screen will appear.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

LANGUAGE CODE LIST

DVD

No.

Language

Country code

No.

Language

Country code

Afar

4747

4748

4752

4759

4764

4765

4771

4772

4847

4851

4853

4854

4855

4860

4861

4864

4947

4961

4965

4971

5047

5051

5072

5158

5160

5161

5165

5166

5167

5247

5255

5256

5261

5264

5271

5347

5350

5358

5360

5367

5447

5455

5464

5467

5471

5547

5551

5557

5560

5565

5566

5569

5647

5655

5669

5747

5757

5758

5759

5760

5761

5765

5767

5771

5847

5860

5861

5866

Latvian;Lettish

Malagasy

Maori

5868

5953

5955

5957

5958

5960

5961

5964

5965

5966

5971

6047

6051

6058

6061

6149

6159

6164

6247

6258

6265

6266

6367

6459

6460

6461

6467

6469

6547

6550

6553

6554

6555

6557

6558

6559

6560

6561

6563

6564

6565

6566

6567

6568

6569

6647

6652

6653

6654

6655

6657

6658

6660

6661

6664

6665

6666

6669

6757

6764

6772

6855

6861

6961

7054

7161

7254

7267

Abkhazian

Afrikaans

Amharic

Arabic

Macedonian

Malayalam

Mongolian

Moldavian

Marathi

Assamese

Aymara

Azerbaijani

Bashkir

Malay

Byelorussian

Bulgarian

Bihari

Maltese

Burmese

Nauru

Bislama

Nepali

Bengali;Bangla

Tibetan

Breton

Dutch (DUT)

Norwegian

Occitan

Catalan

(Afan)Oromo

Oriya

Panjabi

Corsican

Czech

Welsh

Polish

Danish

Pashto;Pushto

Portuguese

Quechua

Rhaeto-Romance

Kirundi

German (GER)

Bhutani

Greek

English (ENG)

Esperanto

Spanish (SPA)

Estonian

Basque

Romanian

Russian

Kinyarwanda

Sanskrit

Sindhi

Persian

Finnish

Sangho

Fiji

100 Serbo-Croatian

101 Singhalese

102 Slovak

103 Slovenian

104 Samoan

105 Shona

106 Somali

107 Albanian

108 Serbian

109 Siswat

110 Sesotho

111 Sundanese

112 Swedish

113 Swahili

114 Tamil

115 Telugu

116 Tajik

117 Thai

118 Tigrinya

119 Turkmen

120 Tagalog

121 Setswana

122 Tonga

Faroese

French (FRE)

Frisian

Irish

Scots Gaelic

Galician

Guarani

Gujarati

Hausa

Hindi

Croatian

Hungarian

Armenian

Interlingua

Interlingue

Inupiak

Indonesian

Icelandic

Italian (ITA)

Hebrew

Japanese (JPN)

Yiddish

Javanese

Georgian

Kazakh

Greenlandic

Cambodian

Kannada

Korean (KOR)

Kashmiri

Kurdish

123 Turkish

124 Tsonga

125 Tatar

126 Twi

127 Ukrainian

128 Urdu

129 Uzbek

130 Vietnamese

131 Volapuk

132 Wolof

Kirghiz

Latin

Lingala

Laothian

Lithuanian

133 Xhosa

134 Yoruba

135 Chinese (CHI)

136 Zulu

–

_{Download from Www.Somanuals.co}3_m3_{. All Manuals Search And Download.}

0C28

TROUBLESHOOTING GUIDE

Sometimes a performance problem can be easily solved by checking seemingly apparent but often overlooked

possibilities. Before arranging for service, check these items. It could save your time and money.

Problem

Corrective Action

Remote Control Doesn’t Work

Is TV/DVD plugged in?

Power at outlet?

Check batteries in Remote Control.

If outside antenna is being used, check for broken wire.

Check for local interference.

•

Bars On Screen

Picture Distorted or Blurred

Try a new channel, if OK, then possible station trouble.

If outside antenna is being used, check for broken wire.

Try a new channel, if OK, then possible station trouble.

If outside antenna is being used, check for broken wire.

Check for local interference.

Try a new channel, if OK, then possible station trouble.

Is antenna connected to terminal on the back of the set?

If outside antenna is being used, check for broken wire.

Adjust COLOR control.

Try a new channel, if OK, then possible station trouble.

Is antenna connected to terminal on the back of the set?

If outside antenna is being used, check for broken wire.

Check for local interference.

Try a new channel, if OK, then possible station trouble.

Is antenna connected to terminal on the back of the set?

If outside antenna is being used, check for broken wire.

Adjust CONTRAST & BRIGHT control.

Try a new channel, if OK, then possible station trouble.

Is antenna connected to terminal on the back of the set?

If outside antenna is being used, check for broken wire.

Check for local interference.

Adjust CONTRAST & BRIGHT control.

Try a new channel, if OK, then possible station trouble.

Check for local interference.

Picture Rolls Vertically

Lines or Streaks in Picture

No Color

Poor Reception on Some Channels

Ghosts in Picture

Weak Picture

Sound OK, Picture Poor

Picture OK, Sound Poor

No Picture or Sound

Try a new channel, if OK, then possible station trouble.

Is TV/DVD plugged in?

Power at outlet?

Is TV/DVD’S POWER button on?

Is antenna connected to terminal on the back of the set?

If outside antenna is being used, check for broken wire.

Turn off with POWER button and then turn it on after about a minute.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

Closed Caption Problem

My TV is showing captions

that are misspelled.

Possible Remedy

• You are watching a live broadcast and spelling errors made by the

• closed captioning production company may pass through uncorrected.

• A prerecorded program will not show any misspelled words because

• of the normal time available for editing the captions.

My TV will not show the text

• Captions that are delayed a few seconds behind the actual dialogue

in its entirety or there is a delay of • are common for live broadcast. Most captioning production companies

what is being said.

• can display a dialogue to a maximum of 220 words per minute. If a

• dialogue exceeds that rate, selective editing is used to insure that the

• captions remain up-to-date with the current TV screen dialogue.

• Interference caused by building, power lines, thunderstorms, etc.

• may cause scrambled or incomplete captions to appear.

My captions are scrambled with

white boxes on the TV screen.

My program guide listed a TV show • Broadcasters may at times use a time compression process to the

as being closed captioned but none • actual program so that additional advertising time can be given.

of the captions were displayed.

• Since the decoder cannot read the compressed information,

• captions will be lost.

My TV screen shows a black box

on certain channels.

• You are in the TEXT mode. Select CAPTION mode or CAPTION

• [OFF].

–

_{Download from Www.Somanuals.co}3_m5_{. All Manuals Search And Download.}

0C28

DVD

If the TV/DVD does not perform properly when operated as instructed in this Owner’s Manual, check the

player, consulting the following checklist.

Symptom

No power.

let.

Cause

Loose power plug.

Remedy

Insert the power plug firmly into the wall out-

•

The player does not

respond to the

The remote control is not aimed Aim the remote control directly at the sensor

•

at the sensor on the TV/DVD.

Obstacles present between the

remote control and the sensor.

The remote control is too far

away from the TV/DVD.

Dead batteries.

on the TV/DVD.

Remove the obstacles from the signal path.

•

remote control.

Use the remote control within 7m of

the TV/DVD.

Replace the batteries.

Connect the video cables firmly.

Insert a correct video disc that plays on this

TV/DVD.

Insert a disc.

Clean the disc.

Place the disc correctly, with the label side up.

Cancel the parental lock or change the control

level.

•

No picture

Loose video connection.

Wrong disc.

Disc cannot be

played

No disc.

Dirty disc.

Disc is placed upside down.

Parental lock is active.

•

No sound

Loose audio connection.

The power of the connected

audio component is off.

Connect the audio cables firmly.

Turn the power of the audio component on.

•

Wrong audio output settings.

Wrong input settings on the

connected audio component.

Immediately after playing,

press fast forward or in reverse.

Correct the audio output settings.

Correct the input settings on the audio

component.

There are some cases where pictures may be

slightly distorted, which are not a sign of a

malfunction.

No malfunction.

•

Distorted picture

Audio or subtitle

language does not

match the setup.

The camera angle

cannot be changed.

The selected language is not

available for audio or subtitles

on the DVD.

The DVD does not contain

sequences recorded from

different camera angles.

The DVD does not contain

audio source or subtitles in the

selected language.

That operation is prohibited by

the TV/DVD or disc.

•

Audio or subtitle

language cannot be

changed.

"Prohibited icon"

appears on the

screen, prohibiting

an operation.

CD sound dropout

No CD reproduction

DVD picture dropout

DVD picture freeze

DVD picture in mosaic

No DVD reproduction

Scratched disc

Replace the disc with unscratched one.

•

NOTES:

Some functions are not available in specific modes, but this is not a malfunction. Read the description in

this Owner’s Manual for details on correct operations.

•

Playback from a desired track and random playback are not available during program playback.

•

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

MAINTENANCE

CABINET CLEANING

SERVICING

Wipe the front panel and other exterior surfaces of

the TV/DVD with a soft cloth immersed in luke-

warm water and wrung dry.

Never use a solvent or alcohol. Do not spray insec-

ticide liquid near the TV/DVD. Such chemicals

may cause damage and discoloration to the

exposed surfaces.

Should your TV/DVD become inoperative, do not

try to correct the problem by yourself. There are no

user-serviceable parts inside. Turn off, unplug the

power cord, and please call our help line at 1-800-

968-3429, to locate an Authorized Service Center.

•

IF THE LASER OPTICAL PICKUP UNIT IS DIRTY

If the player still does not perform properly when it is operated while referring to the relevant sections and to

"TROUBLESHOOTING GUIDE" in this Owner's Manual, the laser optical pickup unit may be dirty. Consult

your dealer or an Authorized Service Center for inspection and cleaning of the laser optical pickup unit.

•

To clean-off, use a soft cloth.

•

DISC HANDLING

Do not use a hard cloth since this will mar the disc.

Wipe the disc in a straight line from center to edge.

Never wipe with a circular motion.

Use discs which have the following logos on them.

(Optical audio digital discs.)

•

Do not use detergent or abrasive cleaning agents.

Handle the discs so that fingerprints and dust do

not adhere to the surfaces of the discs.

Always store the disc in its protective case when it

is not used.

•

–

_{Download from Www.Somanuals.co}3_m7_{. All Manuals Search And Download.}

0C28

SPECIFICATIONS

GENERAL SPECIFICATIONS

ELECTRICAL SPECIFICATIONS

Sound output:

2 speakers, 1W, 8 ohm

Television system:

NTSC-M

TV Standard

OTHER SPECIFICATIONS

Terminals

Closed caption system: §15.119/FCC

Channel coverage:

Antenna input:

VHF/UHF/CATV

75 ohm unbalanced (F-type)

RCA connector [ 1

RCA connector [ 2

VHF:

UHF:

CATV:

2 ~ 13

14 ~ 69

Video input:

Audio L/R input:

Headphone:

Coaxial digital

audio output

(only DVD):

2 ~13, A ~ W,

W+1 ~ W+84,

A-5 ~ A-1, 5A

181 channel

frequency synthesized

tuning system

Direct access keyboard,

programmable

scan and up/down

1/8” stereo (3.5 mm)

Tuning System:

Channel access:

One pin jack,

500m Vpp (75 ohm)

Analog audio L/R

output (only DVD): RCA connector [ 2

Remote control:

Digital encoded

infrared light system

Operating

temperature:

5ºC to 40ºC

DVD

(41ºF~104ºF)

Power requirements: AC 120V, 60Hz

Power consumption

Product type:

Discs:

Output signal format: NTSC color

Frequency response

(out put jack)

DVD (linear sound): 20 Hz to 22 kHz

(sample rate: 48 kHz)

DVD Player

DVD video, Audio CD

(Maximum):

Picture tube:

Dimensions:

90W

19"

H:19-5/8” (498mm)

W:19-3/16” (487mm)

D:18-21/32” (474mm)

41.9 lbs (19kg)

Remote Control Unit with

2"AA"batteries

Owner’s Manual

20 Hz to 44 kHz

(sample rate: 96 kHz)

20 Hz to 20 kHz

Weight:

Accessories:

CD:

Signal-to-noise ratio

(S/N ratio)(out put jack)

CD:

100 dB (EIAJ)

Dynamic range

(out put jack)

DVD (linear sound): 85 dB

CD:

84 dB (EIAJ)

Total distortion factor

CD:

Wow and flutter:

0.07% (EIAJ)

Below the measurement

limitation (+/-0.001%

W PEAK) (EIAJ)

Designs and specifications are subject to change without notice and without our legal obligation.

If there is a discrepancy between languages, the default language will be English.

•

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

7.Ventanilla del sensor del mando a distancia

8.Botón STOP

Detiene la operación del disco.

9.Botón REV

Reproduce rápidamente hacia atrás hasta un

punto deseado.

INDICE

ꢀꢀCONTROLES DE OPERACIÓN Y FUNCIONES . . . . . 39

PANEL FRONTAL DEL TELEVISOR/DVD. . . . . . . . . . 39

MANDO A DISTANCIA. . . . . . . . . . . . . . . . . . . . . . . . . 39

VISTA POSTERIOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

ꢀꢀPREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 40

CONEXIONES DE ANTENA/TELEVISIÓN

10. Botón PLAY

POR CABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

INSTALACIÓN DE LAS PILAS. . . . . . . . . . . . . . . . . . . 41

CONEXIÓN A TOMAS DE ENTRADA EXTERNA. . . . 41

CONEXIÓN A UN SISTEMA ESTÉREO (Para DVD) . . 41

CONEXIÓN A UN AMPLIFICADOR EQUIPADO CON

TOMAS DE ENTRADA DIGITAL, PLATINA MD O

PLATINA DAT (Para DVD) . . . . . . . . . . . . . . . . . . . . . . 41

CONEXIÓN A UN DECODIFICADOR DOLBY DIGITAL

O A UN DECODIFICADOR DTS (Para DVD) . . . . . . . . 41

Inicia la reproducción del contenido del disco.

Púlselo para cambiar a un modo de DVD cuando

modo de televisor.

11. Botón FWD

Reproduce rápidamente hacia adelante hasta un

punto deseado.

12. Botón PAUSE

Hace una pausa en la operación del disco.

13. Botón OPEN/CLOSE

TV SECTION

Púlselo para insertar discos en la bandeja o

retirarlos de ella.

ꢀꢀPREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . . . 42

SELECCIÓN DE IDIOMA . . . . . . . . . . . . . . . . . . . . . . . 42

PREAJUSTE DE CANALES. . . . . . . . . . . . . . . . . . . . . . 42

DVD SECTION

14. Toma HEADPHONE

Para conectar auriculares (no suministrados) y

escuchar en privado.

ꢀꢀREPRODUCCIÓN DE UN DISCO . . . . . . . . . . . . . . . . 43

REPRODUCCIÓN DE UN DVD DE VÍDEO O UN CD DE

AUDIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

15. Botón MODE

Activa el modo de reproducción programada o el

modo de reproducción aleatoria.

16. Botones de números

CONTROLES DE

OPERACIÓN Y FUNCIONES

Modo del televisor:

Pulse dos dígitos para tener acceso directamente

al canal deseado.

PANEL FRONTAL DEL

TELEVISOR/DVD

Recuerde pulsar "0" antes de elegir un canal de

un solo dígito.

Botón +100

Consulte la figura 1 de la página 8

Púlselo para seleccionar canales de televisión por

cable cuyo número sea igual o superior al 100.

Modo DVD:

Púlselo para introducir el número deseado.

Botón +10

MANDO A DISTANCIA

Consulte la figura 2 de la página 8

Púlselo para introducir los números deseados

cuyo número sea igual o superior al 10.

17. Botón SLEEP

VISTA POSTERIOR

Pulse el botón SLEEP para visualizar el tempo-

rizador para dormir y activar la función. La hora

de apagado puede determinarse por el número de

veces que usted pulsa el botón. (0, 10, 20, 30, 90,

0 minutos)

Consulte la figura 3 de la página 9

1.Bandeja de carga del disco

2.Toma de entrada VIDEO

Conecte aquí la toma de salida de vídeo de una

videocámara o de una videograbadora.

18. Botones SKIP

Salta capítulos o pistas hasta un punto deseado.

3.Tomas de entrada AUDIO L/R

Conecte aquí las tomas de salida de audio de una

videocámara o de una videograbadora.

4.Botón POWER

Púlselo para conectar y desconectar la alimentación.

19. Botón ZOOM

Amplia parte de una imagen de DVD reproducida.

20. Botón SETUP

Púlselo para activar o salir del modo de menús de

televisor o preparación de DVD.

5.Botones VOLUME K/L

Púlselos para controlar el nivel del volumen para

el DVD y el televisor.

21. Botón TITLE

Visualiza el menú de títulos.

22. Botón CLEAR

6.Botones CHANNEL K/L

Repone un ajuste.

Púlselo para seleccionar el canal memorizado.

Púlselo para cambiar a un modo de televisor cuan-

do modo de DVD.

23. Botón DISPLAY

–

_{Download from Www.Somanuals.co}3_m9_{. All Manuals Search And Download.}

0C28

Modo del televisor:

38. Toma de salida de audio digital COAXIAL

Conéctela a la entrada digital de un amplificador o

decodificador externo.

Púlselo para visualizar el número del canal en la

pantalla. Si lo pulsa de nuevo, el número del canal

desaparecerá.

Modo de DVD:

Visualiza el estado actual en la pantalla del televi-

sor con fines de comprobación.

39. Toma de salida AUDIO L/R

Conéctela a la entrada de audio analógico de un

amplificador o decodificador externo.

NOTA: Las tomas de entrada de audio (roha y

blanca) en el lado trasero sirven para pro-

ducir no el son televisor ni el son de

entrada externa, sino el son DVD.

24. Botón SEARCH MODE

Púlselo para localizar un punto deseado.

25. Botón AUDIO

Púlselo para seleccionar un idioma de audio o un

modo de sonido deseado.

40. Toma de entrada ANT.

Conéctela a una antena, sistema de televisión por

cable o sistema de satélite.

26. Botón SUBTITLE

Púlselo para seleccionar un idioma de subtítulos

deseado.

27. Botón REPEAT

Repite la reproducción del disco, título, capítulo o

pista actual.

PREPARACIÓN PARA LA

UTILIZACIÓN

28. Botón ANGLE

Púlselo para cambiar el ángulo de la cámara y

verde, desde un ángulo diferente, la secuencia que

está siendo reproducida.

CONEXIONES DE ANTENA/

TELEVISIÓN POR CABLE

29. Botón A-B REPEAT

Repite la reproducción de una sección seleccionada.

ANTENA COMBINADA DE VHF/UHF

La antena de varilla de VHF/UHF (no suministrada)

es desmontable. Inserte el vástago de la antena en el

agujero de la parte superior del televisor/DVD.

Conecte la antena de varilla de VHF/UHF o la antena

combinada de VHF/UHF al terminal ANT. del televi-

sor/DVD como se muestra en el diagrama de abajo.

Para obtener la mejor recepción, extienda completa-

mente la antena de varilla de VHF/UHF y haga los

ajustes necesarios. (Evite tocar la sección superior

cuando haga el ajuste.)

30. Botón RETURN

Para volver a la operación anterior.

31. Botón ENTER

Púlselo para establecer un ajuste.

32. Botones de flechas

Modo de televisor:

Púlselo para seleccionar un modo de ajuste desde

el menú que aparece en la pantalla del televisor.

Púlselo para seleccionar o ajustar desde un menú

particular.

Modo de DVD:

Se utiliza cuando se hacen ajustes mientras se

observa la visualización en una pantalla de televisor.

NOTA:

33. Botón DISC MENU

Antes de enchufar la antena de varilla en un terminal

de antena, compruebe que la clavija no esté doblada.

Si lo está, enderece la clavija como se muestra en la

ilustración y luego enchufe la clavija en el terminal

de antena.

Visualiza menús en el DVD.

34. Botón SELECT

Púlselo para cambiar a un modo de televisor,

modo de entrada externa o modo de DVD.

35. Botón MUTE

Pulse el botón MUTE para apagar el sonido de un

programa de TV. La visualización del nivel del

sonido cambia de ROJO CLARO a AZUL

CLARO.) Pulse de nuevo el botón MUTE o el

botón VOL K o L para restaurar el sonido.

Consulte la figura 4 de la página 10

NOTA:

La conexión de una antena interior puede que no pro-

porcione siempre una recepción de TV aceptable.

36. Botón PICTURE

Presione para entrar en el modo de ajuste de ima-

gen.

ANTENAS SEPARADAS DE VHF/UHF

En algunas áreas será necesario utilizar una antena

exterior.

37. Cable de alimentación

Conéctelo a una toma de CA convencional (120

V/60 Hz).

NOTA: Retire el cable de alimentación del gancho

para evitar romperlo antes de conectarlo a

una toma de CA convencional.

Consulte la figura 5 de la página 10

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

TELEVISIÓN POR CABLE SIN CAJA DE

CONVERTIDOR/DECODIFICADOR

Utilice esta conexión si su sistema de televisión por

cable se conecta directamente a su televisor/DVD sin

necesidad de caja de convertidor.

CONEXIÓN A UN SISTEMA

ESTÉREO (Para DVD)

Consulte la figura 9 de la página 13

NOTAS:

Consulte la figura 6 de la página 11

Asegúrese de desconectar la alimentación a todos

los componentes del sistema antes de hacer la

conexión a otro componente.

•

TELEVISIÓN POR CABLE CON CAJA

DE CONVERTIDOR/DECODIFICADOR

O CAJA DE SATÉLITE

Si su proveedor de servicios de televisión por cable le

suministra una caja de convertidor o si usted utiliza

un sistema de satélite, podrá utilizar la conexión bási-

ca mostrada aquí.

Consulte el manual del propietario de su sistema

estéreo y de cualquier otro componente que vaya a

conectar al televisor/DVD.

Las tomas de entrada de audio (roha y blanca) en el

lado trasero sirven para producir no el son televisor

ni el son de entrada externa, sino el son DVD.

CONEXIÓN A UN

Consulte la figura 7 de la página 11

AMPLIFICADOR EQUIPADO

CON TOMAS DE ENTRADA

DIGITAL, PLATINA MD O

PLATINA DAT (Para DVD)

INSTALACIÓN DE LAS PILAS

1) Abra la tapa del compartimiento de las pilas del

mando a distancia presionándola en el sentido de

la flecha.

Utilice un cable digital coaxial (de venta en el comer-

cio) para las conexiones de audio.

2) Inserte 2 pilas tamaño "AA" en su compartimiento

colocando las polaridades (+/-) en sus posiciones

correspondientes.

Consulte la figura 10 de la página 13

NOTAS:

3) Vuelva a poner la tapa.

La fuente de audio de un disco del formato de

•

sonido ambiental Dolby Digital de 5,1 canales no

puede ser grabada como sonido digital por una

platina MD o DAT.

CONEXIÓN A TOMAS DE

ENTRADA EXTERNA

Cuando vea un programa grabado en otra fuente

(videograbadora o videocámara), utilice las tomas de

entrada de audio/vídeo de la parte delantera del tele-

visor/DVD.

Asegúrese de desconectar la alimentación de todos

los componentes del sistema antes de hacer la

conexión a otro componente.

•

Consulte los manuales del propietario de los com-

ponentes que vaya a conectar al televisor/DVD.

•

Conecte las tomas de salida de audio/vídeo de otra

fuente a las tomas AUDIO L/R y VIDEO de este tele-

visor/DVD. Y luego pulse el botón SELECT hasta

que "VIDEO" aparezca en la pantalla.

Ponga DOLBY DIGITAL y DTS en OFF para la

•

salida de audio en el modo de preparación. La

reproducción en el televisor/DVD utilizando los

ajustes incorrectos puede generar distorsión de

ruido, y también puede estropear los altavoces.

NOTA:

El audio se silenciará cuando DOLBY DIGITAL se

•

ponga en OFF y VIRTUAL 3D se ponga en ON

para la salida de audio en el modo de preparación y

usted seleccione la fuente de audio del formato de

sonido ambiental Dolby Digital de 5,1 canales.

Cuando conecte una videograbadora monoaural

•

(otra fuente) a este televisor/DVD, conecte la toma

de salida de audio de la videograbadora monoaural

(otra fuente) a la toma AUDIO L de este televi-

sor/DVD. El audio saldrá igualmente en los canales

L y R.

Consulte la figura 8 de la página 12

Conexiones de antena/televisión por cable

Continúa en la página siguiente.

–

_{Download from Www.Somanuals.co}4_m1_{. All Manuals Search And Download.}

0C28

CONEXIÓN A UN

DECODIFICADOR DOLBY

DIGITAL O A UN

TV SECTION

PREPARACIÓN PARA LA

UTILIZACIÓN

Para empezar

DECODIFICADOR DTS

(Para DVD)

Si se utiliza este televisor/DVD para reproducir

fuentes del formato de sonido ambiental Dolby

Digital de 5,1 canales o de sonido ambiental DTS, el

televisor/DVD dará salida a un flujo de datos Dolby

Digital o DTS desde su toma de salida de audio digi-

tal COAXIAL. Conectando el reproductor a un

decodificador Dolby Digital o DTS, usted podrá dis-

frutar de un ambiente más convincente y real con un

sonido ambiental potente y de alta calidad de tipo

profesional tal como el que se oye en salas de cine.

Utilice cables digitales coaxiales (de venta en el com-

ercio) para las conexiones de audio.

Conecte el cable de alimentación a una toma de CA

convencional.

NOTA: Si aparecen algunos dígitos en la esquina de

la pantalla, pulse el botón POWER sin des-

enchufar el cable de alimentación.

Pulse el botón POWER para encender el

televisor/DVD.

Consulte la figura 11 de la página 14

NOTAS:

Pulse el botón SELECT del mando a distancia hasta

que el número del canal o "TV" aparezca en la pan-

talla. Luego pulse el botón TV.

Asegúrese de desconectar la alimentación de todos

los componentes del sistema antes de hacer la

conexión a otro componente.

•

SELECCIÓN DE IDIOMA

Si desea cambiar el idioma del menú en pantalla, siga

el procedimiento de abajo.

Consulte los manuales del propietario de los com-

ponentes que vaya a conectar al televisor/DVD.

Si conecta un decodificador Dolby Digital, ponga

DOLBY DIGITAL en ON para la salida de audio

en el modo de preparación.

Si conecta un decodificador DTS, ponga DTS en

ON para la salida de audio en el modo de

preparación.

•

Pulse el botón MENU para que la visualización del

menú aparezca en la pantalla del televisor.

A menos que se haga la conexión a un decodifi-

•

cador Dolby Digital o DTS, ponga DOLBY DIGI-

TAL y DTS en OFF para la salida de audio en el

modo de preparación. La reproducción en el televi-

sor/DVD utilizando los ajustes incorrectos puede

generar distorsión de ruido, y también puede estro-

pear los altavoces.

Pulse el botón de flecha K o L para apuntar a

"LENGUAJE".

Seleccione "ENGLISH" (inglés), "ESPAÑOL" o

"FRANÇAIS" (francés) utilizando el botón de flecha

B o s.

El audio se silenciará cuando DOLBY DIGITAL se

•

ponga en OFF y VIRTUAL 3D se ponga en ON

para la salida de audio en el modo de preparación y

usted seleccione la fuente de audio del formato de

sonido ambiental Dolby Digital de 5,1 canales.

Pulse el botón MENU para salir del menú.

NOTA: Para el modo del televisor y el modo del

DVD se deberá seleccionar un idioma de

visualización en pantalla.

Fabricado bajo licencia de Dolby

Laboratories. “Dolby” y el símbolo de la D

doble son marcas de fábrica de Dolby

Laboratories. Trabajos confidenciales sin

PREAJUSTE DE CANALES

“DTS” y “DTS Digital Out” son marcas de

fábrica de Digital Theater Systems, Inc.

Para preajustar un canal o cambiar un canal de prea-

juste, siga el procedimiento de abajo.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

DVD SECTION

Pulse el botón MENU para que la visualización del

menú aparezca en la pantalla del televisor.

REPRODUCCIÓN DE UN

DISCO

Pulse el botón de flecha K o L para apuntar a

"CANALES PROGRAMADOS". Luego pulse el

botón de flecha B.

REPRODUCCIÓN DE UN DVD

DE VÍDEO O UN CD DE AUDIO

DVD

Pulse el botón de flecha K o L para apuntar a

"MEMO AUTOMÁTICA". Luego pulse el botón de

flecha B.

El sintonizador explora y memoriza todos los canales

activos de su zona.

Para empezar

Conecte la alimentación del televisor, amplificador y

cualquier otro componente que esté conectado al

reproductor DVD. (Cambie el sistema de entrada para

adaptarlo al reproductor DVD, y compruebe que el

volumen del sonido sea correcto.)

El televisor distingue entre los canales de TV con-

vencional y los canales de televisión por cable.

•

Cuando termine la función AUTO MEMO, el canal

memorizado más bajo vuelve a aparecer en la pan-

talla.

•

Pulse el botón POWER.

Cuando pulse el botón de flecha K o L después de

seleccionar AUTO MEMO, el sintonizador se

detendrá en los canales sin memorizar solamente.

•

¡La alimentación se conectará.

El televisor puede considerar canales de TV como

•

Pulse el botón OPEN/CLOSE.

canales CATV según las condiciones de la recep-

ción. En este caso, active de nuevo la función

AUTO MEMO en condiciones de recepción fina.

¡La bandeja de carga del disco se abrirá.

[FUNCIÓN DE ADICIÓN/BORRADO]

1) Pulse el botón MENU para que la visualización

del menú aparezca en la pantalla del televisor.

2) Pulse el botón de flecha K o L para apuntar a

"CANALES PROGRAMADOS". Luego pulse el

botón de flecha B.

Ponga un disco en la bandeja.

¡Asegúrese de que el disco esté correctamente asen-

tado en el hueco correcto, con el lado de la etiqueta

hacia arriba.

3) Pulse el botón de flecha K o L para apuntar a

"AÑADIR/BORRAR". Luego pulse el botón de

flecha B.

Pulse el botón PLAY.

4) Utilice el botón de flecha K o L para seleccionar

el canal que desee memorizar o borrar de la

memoria.

¡La bandeja se cerrará automáticamente y la repro-

ducción empezará desde el primer capítulo o pista

del disco. Necesitará pulsar el botón PLAY sólo

cuando la bandeja haya sido cerrada pulsando el

botón OPEN/CLOSE.

NOTA: La visualización volverá a la pantalla en

unos 10 segundos. Realice la función

"AÑADIR/BORRAR" mientras aparece la

visualización en la pantalla.

¡Cuando reproduzca un DVD que tenga grabado un

menú de títulos, el menú tal vez aparezca en la pan-

talla. En este caso, consulte "UTILIZACIÓN DEL

MENÚ DE TÍTULOS".

Pulse el botón de flecha B o s para encender el

número de canal en AZUL CLARO si usted desea

añadir el canal a la memoria.

•

Pulse el botón de flecha B o s para encender el

número de canal en ROJO CLARO si usted desea

borrar el canal a la memoria.

•

Pulse el botón STOP para detener la reproducción.

5) Pulse el botón MENU para salir del menú.

–

_{Download from Www.Somanuals.co}4_m3_{. All Manuals Search And Download.}

0C28

LIMITED WARRANTY

FUNAI CORP. will repair this SYLVANIA product, free of charge in the USA in the event of defect in materials or

workmanship as follows:

DURATION:

PARTS:

FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the

date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this

warranty.

LABOR: FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of

original retail purchase.

LIMITS AND EXCLUSIONS:

This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail

purchase will be required together with the product to obtain service under this warranty.

This warranty shall not be extended to any other person or transferee.

This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing

or if service was attempted by an unauthorized service center. This SYLVANIA Limited warranty does not apply to

any product not purchased and used in the United States.

This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It

does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not

supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication,

alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this

product or damage which results from fire, flood, lightning or other acts of God.

THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE

CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.

FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY

GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE

USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL

OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF

FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY, AND

FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS

REPRESENTATIVES IN THE UNITED STATES.

ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY A FUNAI AUTHORIZED

SERVICE CENTER. THIS WARRANTY IS VALID WHEN THE UNIT IS CARRIED-IN TO FUNAI

AUTHORIZED SERVICE FACILITY.

IMPORTANT:

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS

THAT VARY FROM STATE TO STATE, IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE

UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI

CORP.

ATTENTION:

FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT

WITHOUT PRIOR NOTICE.

To locate your nearest SYLVANIA Authorized Service Center or for general service procedure,

please call 1-800-968-3429 or write to the following:

FUNAI CORPORATION, INC.

Customer Service

100 North Street; Teterboro, NJ 07608

Tel :1-800-968-3429

PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.

Printed in Malaysia

0EMN01856

TD250UA ####

Download from Www.Somanuals.com. All Manuals Search And Download.

Sharp Laptop ZR 5000 User Manual
Silicon Image Computer Drive SSDS00 3650H R User Manual
Snapper Snow Blower 1694921 User Manual
Sony Stereo System CMT GPX6 User Manual
Sony Webcam VPCF11 User Manual
Spirit Treadmill CT 800 User Manual
Stanton Music Mixer SK FIVE User Manual
Star Manufacturing Food Warmer HFD 1 User Manual
Sunwave Tech Universal Remote SRC 3060 User Manual
Symbol Technologies Network Router AP 4131 User Manual