Sylvania TV DVD Combo 6509DD User Manual

OWNER’S  
MANUAL  
9-INCH COLOR TV/DVD  
6509DD  
This Owner’s Manual is made of  
recycled paper.  
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.  
As an ENERGY STAR®  
Partner, our company has  
determined that this product meets  
the ENERGY STAR® guidelines for  
energy efficiency. ENERGY STAR® is  
a U.S. registered mark.  
If you need additional assistance for set-up or operating after  
reading owner’s manual, please call TOLL FREE : 1-800-968-3429.  
Or visit our WEB SITE at http://www.funai-corp.com  
Download from Www.SoPmlaenauaslse.croema. dAllbMeafnouarles SuesaircnhgAnthd iDsowenqlouaidp. ment  
FIGURE A  
EXAMPLE OF ANTENNA GROUNDING AS PER  
NATIONAL ELECTRICAL CODE  
ANTENNA  
LEAD I N  
WI RE  
GROUND  
CL AMP  
ANTENNA  
DISCHARGE UNIT  
(NEC SECTION 810-20)  
ELECTRI C  
SERVICE  
EQUIPMENT  
GROUNDING CONDUCTORS  
(NEC SECTION 810-21)  
GROUND CLAMPS  
NEC  
-
NATIONAL ELECTRICAL CODE  
POWER SERVICE GROUNDING  
ELECTRODE SYSTEM  
(NEC ART 250, PART H)  
S2898A  
12.Power-Cord Protection-Power-supply cords should be  
routed so that they are not likely to be walked on or  
pinched by items placed upon or against them, paying par-  
ticular attention to cords at plugs, convenience receptacles,  
and the point where they exit from the appliance.  
19.Damage Requiring Service-Unplug this TV/DVD from  
the wall outlet and refer servicing to qualified service per-  
sonnel under the following conditions:  
a. When the power-supply cord or plug is damaged or frayed.  
b. If liquid has been spilled, or objects have fallen into the  
TV/DVD.  
13.Outdoor Antenna grounding-If an outside antenna or  
cable system is connected to the TV/DVD, be sure the  
antenna or cable system is grounded so as to provide some  
protection against voltage surges and built-up static  
charges. Article 810 of the National Electrical Code,  
ANSI/NFPA No. 70, provides information with respect to  
proper grounding of the mast and supporting structure,  
grounding of the lead-in wire to an antenna discharge unit,  
size of grounding conductors, location of antenna-discharge  
unit, connection to grounding electrodes, and requirements  
for the grounding electrode. (Fig. A)  
c. If the TV/DVD has been exposed to rain or water.  
d. If the TV/DVD does not operate normally by following the  
operating instructions. Adjust only those controls that are  
covered by the operating instructions, as improper adjust-  
ment of other controls may result in damage and will often  
require extensive work by a qualified technician to restore  
the TV/DVD to its normal operation.  
e. If the TV/DVD has been dropped or damaged in any way.  
f. When the TV/DVD exhibits a distinct change in perfor-  
mance-this indicates a need for service.  
14.Lightning-For added protection for this TV/DVD receiver  
during a lightning storm, or when it is left unattended and  
unused for long periods of time, unplug it from the wall  
outlet and disconnect the antenna or cable system. This will  
prevent damage to the TV/DVD due to lightning and  
power-line surges.  
20.Replacement Parts-When replacement parts are required,  
be sure the service technician has used replacement parts  
specified by the manufacturer that have the same character-  
istics as the original part. Unauthorized substitutions may  
result in fire, electric shock, injury to persons or other haz-  
ards.  
15.Power Lines-An outside antenna system should not be  
located in the vicinity of overhead power lines or other  
electric light or power circuits, or where it can fall into  
such power lines or circuits. When installing an outside  
antenna system, extreme care should be taken to keep from  
touching such power lines or circuits as contact with them  
might be fatal.  
21.Safety Check-Upon completion of any service or repairs to  
this TV/DVD, ask the service technician to perform routine  
safety checks to determine that the TV/DVD is in proper  
operating condition.  
22.Heat-This TV/DVD product should be situated away from  
heat sources such as radiators, heat registers, stoves, or  
other products (including amplifiers) that produce heat.  
16.Overloading-Do not overload wall outlets and extension  
cords as this can result in a risk of fire or electric shock.  
17.Object and Liquid Entry-Never push objects of any kind  
into this TV/DVD through openings as they may touch dan-  
gerous voltage points or short out parts that could result in  
a fire or electric shock. Never spill liquid of any kind on  
the TV/DVD.  
18.Servicing-Do not attempt to service this TV/DVD yourself  
as opening or removing covers may expose you to danger-  
ous voltage or other hazards. Refer all servicing to qualified  
service personnel.  
EN  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
0C28  
PRECAUTIONS  
IMPORTANT COPYRIGHT INFORMATION  
LASER SAFETY  
Unauthorized copying, broadcasting, public perfor-  
mance and lending of discs are prohibited.  
This unit employs a laser. Only a qualified service  
person should remove the cover or attempt to ser-  
vice this device, due to possible eye injury.  
FCC WARNING- This equipment may gener-  
ate or use radio frequency energy. Changes or  
modifications to this equipment may cause  
harmful interference unless the modifications  
are expressly approved in the instruction man-  
ual. The user could lose the authority to oper-  
ate this equipment if an unauthorized change  
or modification is made.  
CAUTION: USE OF CONTROLS OR ADJUST-  
MENTS OR PERFORMANCE OF PROCE-  
DURES OTHER THAN THOSE SPECIFIED  
HEREIN MAY RESULT IN HAZARDOUS  
RADIATION EXPOSURE.  
CAUTION: VISIBLE AND INVISIBLE LASER  
RADIATION WHEN OPEN AND INTERLOCK  
DEFEATED. DO NOT STARE INTO BEAM.  
LOCATION: INSIDE, NEAR THE DECK  
MECHANISM.  
RADIO-TV INTERFERENCE  
This equipment has been tested and found to com-  
ply with the limits for a Class B digital device, pur-  
suant to Part 15 of the FCC Rules. These limits are  
designed to provide reasonable protection against  
harmful interference in a residential installation.  
This equipment generates, uses, and can radiate  
radio frequency energy and, if not installed and  
used in accordance with the instructions, may cause  
harmful interference to radio communications.  
However, there is no guarantee that interference  
will not occur in a particular installation. If this  
equipment does cause harmful interference to  
radio or television reception, which can be deter-  
mined by turning the equipment off and on, the  
user is encouraged to try to correct the interfer-  
ence by one or more of the following measures:  
1) Reorient or relocate the receiving antenna.  
2) Increase the separation between the equipment  
and receiver.  
This Class B digital apparatus complies with  
Canadian ICES-003.  
Cet appareil numérique de la classe B est con-  
forme à la norme NMB-003 du Canada.  
CAUTION: TO PREVENT ELECTRIC SHOCK,  
MATCH WIDE BLADE OF PLUG TO WIDE  
SLOT, FULLY INSERT.  
ATTENTION: POUR ÉVITER LES CHOC  
ÉLECTRIQUES, INTRODUIRE LA LAME LA  
PLUS LARGE DE LA FICHE DANS LA  
BORNE CORRESPONDANTE DE LA PRISE  
ET POUSSER JUSQU’AU FOND.  
A NOTE ABOUT RECYCLING  
This product’s packaging materials are recyclable  
and can be reused. Please dispose of any materials  
in accordance with your local recycling regula-  
tions.  
Batteries should never be thrown away or inciner-  
ated but disposed of in accordance with your local  
regulations concerning chemical wastes.  
3) Connect the equipment into an outlet on a cir-  
cuit different from that to which the receiver is  
connected.  
4) Consult the dealer or an experienced radio/TV  
technician for help.  
The serial number of this product may be found on the back of the unit. No other TV/DVD has the same serial  
number as yours. You should record the number and other vital information here and retain this book as a per-  
manent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.  
Date of Purchase  
Dealer Purchase from  
Dealer Address  
Dealer Phone No.  
Model No.  
Serial No.  
EN  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
0C28  
LOCATION  
SUPPLIED ACCESSORY  
For safe operation and satisfactory performance of  
your TV/DVD, keep the following in mind when  
selecting a place for its installation:  
Remote Control Unit  
(PART NO.: NE207UD)  
Shield it from direct sunlight and keep it away from  
sources of intense heat.  
Avoid dusty or humid places.  
Avoid places with insufficient ventilation for proper  
heat dissipation. Do not block the ventilation holes at  
the top and bottom of the unit. Do not place the unit  
on a carpet because this will block the ventilation  
holes.  
Install unit in a horizontal position.  
Avoid locations subject to strong vibration.  
2 AA Batteries  
Indoor Antenna  
(PART NO.:  
0EMN00723 or 0EMN01183)  
Matching Adapter  
(300ohm-75ohm)  
(PART NO.: 1813641 or  
1780258 or UCPGANTPK004)  
Car Battery Cord  
(PART NO.: WPC0202GA001  
or WPC0202HHH001)  
Do not place the TV/DVD near strong magnetic fields.  
Avoid moving TV/DVD to locations where temper-  
ature differences are extreme.  
AVOID THE HAZARDS OF  
SYMBOLS USED IN THIS MANUAL  
The following symbols below appear in some head-  
ings and notes in this manual, with the following  
meanings  
ELECTRICAL SHOCK AND FIRE  
Do not handle the power cord with wet hands.  
Do not pull on the power cord when disconnecting  
it from an AC wall outlet. Grasp it by the plug.  
If, by accident, water is spilled on your unit, unplug  
the power cord immediately and take the unit to our  
Authorized Service Center for servicing.  
Do not put your fingers or objects into the  
TV/DVD disc loading tray.  
Do not place anything directly on top of the unit.  
TV  
: Description refers to TV operation (in the TV mode).  
DVD-V  
: Description refers to playback of DVD video discs  
(in the DVD mode).  
CD  
: Description refers to playback of audio CDs  
(in the DVD mode).  
WARNING  
MP3  
: Description refers to playback of MP3 discs  
(in the DVD mode).  
Moisture condensation may occur inside the unit  
when it is moved from a cold place to a warm place,  
or after heating a cold room or under conditions of  
high humidity. If a DVD is played in a TV/DVD  
which has moisture, it may damage the DVD and  
TV/DVD. Therefore when the condensation occurs  
inside the unit, turn POWER on and allow at least 2  
hours for the unit to dry out.  
QUICK  
: Description refers to the items to be set by the  
QUICK mode (in the DVD mode).  
EN  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
0C28  
TABLE OF CONTENTS  
C IMPORTANT SAFEGUARDS . . . . . . . . . . . . .2  
C PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . .4  
C FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . .7  
C SEARCH FUNCTION . . . . . . . . . . . . . . . . . .21  
TRACK SEARCH . . . . . . . . . . . . . . . . . . . . . .21  
TITLE / CHAPTER SEARCH . . . . . . . . . . . . .21  
TIME SEARCH . . . . . . . . . . . . . . . . . . . . . . . .21  
MARKER SETUP SCREEN . . . . . . . . . . . . . .21  
C
OPERATING CONTROLS AND FUNCTIONS . . .8  
INSTALLING THE BATTERIES . . . . . . . . . . .9  
C SPECIAL PLAYBACK FUNCTION . . . . . . . .22  
REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22  
PROGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . .22  
RANDOM PLAYBACK . . . . . . . . . . . . . . . . .22  
C PREPARATION FOR USE . . . . . . . . . . . . . . .10  
ANTENNA/CABLE CONNECTIONS . . . . . . .10  
INDOOR ANTENNA . . . . . . . . . . . . . . . . . . .10  
CONNECTING TO EXTERNAL INPUT JACKS .11  
C PLAYING A MP3 DISC . . . . . . . . . . . . . . . . . .23  
MP3 PLAYBACK . . . . . . . . . . . . . . . . . . . . . .23  
TRACK SELECTION . . . . . . . . . . . . . . . . . . .23  
PROGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . .23  
RANDOM PLAYBACK . . . . . . . . . . . . . . . . .23  
CONNECTING TO A STEREO SYSTEM . . . .12  
CONNECTING TO AN AMPLIFIER  
EQUIPPED WITH DIGITAL INPUT JACKS,  
MD DECK OR DAT DECK (for DVD only) . .12  
CONNECTING TO A DOLBY DIGITAL  
DECODER (for DVD) . . . . . . . . . . . . . . . . . . .13  
C CHANGING THE SETTINGS . . . . . . . . . . . .24  
SUBTITLE LANGUAGE . . . . . . . . . . . . . . . .24  
AUDIO LANGUAGE . . . . . . . . . . . . . . . . . . .24  
STEREO SOUND MODE . . . . . . . . . . . . . . . .24  
CAMERA ANGLE . . . . . . . . . . . . . . . . . . . . . .24  
BLACK LEVEL SETTING . . . . . . . . . . . . . . .24  
VIRTUAL SURROUND . . . . . . . . . . . . . . . . .24  
TV SECTION  
C SET UP FOR USE . . . . . . . . . . . . . . . . . . . . .14  
CHANNEL SET UP FOR THE FIRST TIME . .14  
DELETING (OR ADDING) CHANNEL . . . . .14  
CHANNEL SET UP AGAIN . . . . . . . . . . . . . .15  
SELECTING THE LANGUAGE . . . . . . . . . . .15  
C TV OPERATION . . . . . . . . . . . . . . . . . . . . . . .16  
WATCHING A TV PROGRAM . . . . . . . . . . . .16  
DEGAUSSING . . . . . . . . . . . . . . . . . . . . . . . .16  
PICTURE CONTROL . . . . . . . . . . . . . . . . . . .16  
SLEEP TIMER . . . . . . . . . . . . . . . . . . . . . . . . .17  
C THE ON-SCREEN INFORMATION . . . . . . .25  
C CHANGING THE DVD SETUP ITEMS . . . .26  
LANGUAGE SETTING . . . . . . . . . . . . . . . . .26  
DISPLAY SETTING . . . . . . . . . . . . . . . . . . . .27  
AUDIO SETTINGS . . . . . . . . . . . . . . . . . . . . .27  
PARENTAL CONTROL . . . . . . . . . . . . . . . . .28  
DVD SECTION  
C ABOUT THE DISCS . . . . . . . . . . . . . . . . . . . .18  
PLAYABLE DISCS . . . . . . . . . . . . . . . . . . . . .18  
DISC TYPES . . . . . . . . . . . . . . . . . . . . . . . . . .18  
C TROUBLESHOOTING GUIDE . . . . . . . . . . .29  
C MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . .31  
C PLAYING A DISC . . . . . . . . . . . . . . . . . . . . . .19  
BASIC PLAYBACK . . . . . . . . . . . . . . . . . . . .19  
GENERAL FEATURES . . . . . . . . . . . . . . . . . .19  
DISC MENU . . . . . . . . . . . . . . . . . . . . . . . . . .19  
TITLE MENU . . . . . . . . . . . . . . . . . . . . . . . . .19  
RESUME . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20  
PAUSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20  
STEP BY STEP PLAYBACK . . . . . . . . . . . . .20  
FAST FORWARD/REVERSE SEARCH . . . . .20  
SLOW FORWARD / SLOW REVERSE . . . . .20  
ZOOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20  
DISC HANDLING . . . . . . . . . . . . . . . . . . . . . .31  
C SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . .32  
C WARRANTY . . . . . . . . . . . . . . . . . . .Back Cover  
EN  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
0C28  
FEATURES  
TV Mode  
DVD Mode  
¡Dolby Digital sound  
181 channel capability PLL frequency synthesiz-  
er tuner with direct station call  
(A converter may be necessary to view scrambled  
cable channels.)  
Infrared remote control  
Trilingual on screen menu display selectable in  
English, Spanish, or French  
This player can handle Dolby Digital surround sound  
having 5.1 channels when connected to a Dolby Digital  
decoder.  
¡Still/fast/slow/step playback  
Various playback modes are available including still pic-  
tures, fast forward/reverse, slow motion and step frames.  
¡Random playback for audio CD and MP3  
This player can shuffle the order of tracks to play them in  
random order.  
¡Sleep Timer  
T
he Sleep Timer function enables you to shut off the power  
without pressing POWER after a desired time period.  
¡Program playback for audio CD and MP3  
You can program the order of tracks to play them in any  
desired order.  
¡Auto Shut Off Function  
If there is no air signal input from the antenna terminal and  
no operation for 15 minutes, the TV will turn itself off  
automatically.  
¡DVD menus in a desired language  
You can display DVD menus in a desired language, if  
available on a DVD.  
¡Screen saver/Auto power-off functions  
The screen saver program starts when there is no input  
from the player for five minutes in the stop mode. When  
the screen saver program is activated for 15 minutes, the  
power is automatically turned off.  
¡Subtitles in a desired language  
You can select a desired language for the display subtitles,  
if that language is available on a disc.  
¡Selecting a camera angle  
You can select the desired camera angle, if a disc contains  
sequences recorded from different angles.  
¡Choices for audio language and sound mode  
You can select the desired audio language and sound mode,  
if different languages and modes are available on a disc.  
¡Parental lock  
You can set the control level to limit playback of discs  
which may not be suitable for children.  
¡Automatic detection of discs  
This player automatically detects if the loaded disc is  
DVD, audio CD or MP3 on disc.  
¡On-screen display  
Information about the current operation can be displayed  
on a TV screen, allowing you to confirm the currently  
active functions (such as program playback), on the TV  
screen using the remote control.  
¡Search  
Chapter search / Title search / Track search / Time search  
¡Repeat  
Chapter / Title / Track / Group / All / A-B  
¡Zoom  
Magnified screen can be displayed.  
¡Marker  
The part designated by user can be called back.  
¡Resume Play  
User can resume to playback from the part at which the  
play was stopped.  
¡Virtual Surround  
¡Bit rate indication  
¡DRC (Dynamic range control)  
You can control the range of sound volume.  
EN  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
0C28  
OPERATING CONTROLS AND FUNCTIONS  
[Fig. 1]  
[Fig. 3]  
TV/DVD FRONT PANEL  
TV/DVD REAR VIEW  
DC 13.2V  
ANT.  
L
AUDIO OUT  
R
VIDEO  
L
AUDIO  
R
POWER  
VOLUME  
CHANNEL  
STOP  
SKIP  
PLAY  
SKIP  
PAUSE  
OPEN/CLOSE HEADPHONE  
SEARCH  
COAXIAL  
13  
1 2  
3
4
5
6
7 8 9 101112 14  
37  
38  
39  
40  
41  
[Fig. 2]  
REMOTE CONTROL  
OPEN/  
CLOSE  
POWER PICTURE SELECT  
4
13  
34  
6.CHANNEL K/L (CH.K/L) Buttons [page 14]  
Press to select memorized channel.  
36  
1
4
2
5
8
0
3
6
CH.  
6
Press to change to TV mode when DVD mode.  
16  
7.Remote Sensor Window  
8.STOP Button [page 19]  
Stops operation of the disc.  
7
SLEEP  
9
+100  
VOL.  
5
+10  
ZOOM  
17  
SKIP  
MUTE  
9.SKIP H Button [page 21]  
Plays back from the beginning of the current  
chapter or track.  
9
11  
10  
35  
19  
18  
PLAY  
STOP  
REV  
FWD  
SEARCH (REV) E Button (Front Panel)  
[page 20]  
8
DISC  
MENU  
PAUSE SLOW  
DISPLAY  
During playback or in the pause mode, press and  
hold button down for a few seconds to change  
reverse playback speed.  
12  
23  
33  
32  
31  
30  
ENTER  
SETUP  
TITLE  
RETURN  
10. PLAY Button [page 19]  
20  
21  
22  
Starts playback of the disc contents.  
Press to change to DVD mode when TV mode.  
11. SKIP G Button [page 21]  
Plays back from the beginning of the next chapter  
or track.  
CLEAR SEARCH MODE REPEAT  
A-B  
29  
AUDIO SUBTITLE ANGLE  
MODE  
15  
24  
25  
28  
27  
26  
SEARCH (FWD) D Button (Front Panel)  
[page 20]  
During playback or in the pause mode, press and  
hold button down for a few seconds to change for-  
ward playback speed.  
1.Disc loading tray  
2.VIDEO input Jack [page 11]  
Connect to the video output jack of a video  
camera or VCR.  
12. PAUSE Button [page 20]  
Pauses the current disc operation.  
13. OPEN/CLOSE Button [page 19]  
Press to insert discs into or remove them from the  
tray.  
3.AUDIO L/R input Jacks [page 11]  
Connect to the audio output jacks of a video  
camera or VCR.  
14. HEADPHONE Jack  
To connect headphone (not supplied) for personal  
listening.  
4.POWER Button [page 14]  
Press to turn the power on and off.  
5.VOLUME K/L (VOL. m/n) Buttons  
Press to control the volume level for the DVD and TV.  
EN  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
0C28  
sequence being played back from a different angle.  
15. MODE Button [pages 22-24]  
Activates program playback or random playback mode  
when playing CDs or MP3.  
29. REPEAT A-B [page 22]  
Repeats playback of a selected section.  
16. Number Button  
30. RETURN Button [page 24]  
TV Mode: [page 14]  
Returns to the previous operation.  
Press two digits to directly access the desired  
channel.  
31. ENTER Button [pages 14, 19]  
Press to accept a setting.  
Remember to press a "0" before a single digit  
32. Arrow Buttons  
channel.  
+100 Button–  
TV Mode: [page 14]  
Press to select a setting mode from the menu on  
the TV screen.  
Press to select cable channels which are equal or  
greater than number 100.  
Press to select or adjust from a particular menu.  
DVD Mode: [page 19]  
DVD Mode: [page 21]  
Press to enter the desired number.  
+10 Button–  
Use when making settings while watching the  
display on a TV screen.  
Press to enter the desired numbers which are  
equal or greater than number 10.  
33. DISC MENU Button [page 19]  
Displays the menus in the DVD.  
17. SLEEP Button [page 17]  
34. SELECT Button [pages 11, 19]  
Press to change to TV mode, external input mode  
or DVD mode.  
Press SLEEP to display the sleep timer and start  
the function. The shut off time can be determined  
by the number of times you press this button. (0,  
30, 60, 90, or 120 minutes)  
NOTE: When you select the DVD mode by this  
button, press PLAY or OPEN/CLOSE first.  
Otherwise, the DVD features are not operated.  
18. REV h Button [page 20]  
Press to view the DVD picture in fast reverse  
motion. Press PAUSE, then press this button to begin  
slow motion playback. Press this button repeatedly  
to change the reverse speed of slow motion.  
35. MUTE Button  
Press MUTE to turn off the sound  
portion of the TV program. (Volume level display  
turns LIGHT RED from LIGHT BLUE.) Press  
MUTE again or press VOL. m or n to restore  
sound.  
FWD g Button [page 20]  
Press to fast forward the Disc. Press PAUSE, then  
press this button to begin slow motion playback.  
Press this button repeatedly to change the forward  
speed of slow motion.  
36. PICTURE Button [page 16]  
Press to enter picture adjustment mode.  
19. ZOOM Button [page 20]  
37. Power cord  
Expands the picture to fill the entire screen.  
Connect to a standard AC outlet (120V/60Hz).  
NOTE: Remove the power cord from the hook to  
avoid breaking a wire before you connect  
to a standard AC outlet.  
20. SETUP Button [pages 14, 26-28]  
Press to enter or exit the TV menu or DVD setup  
mode.  
21. TITLE Button [page 19]  
38. AUDIO L/R output Jack  
Connect to the analog audio input of an external  
amplifier or decoder.  
Displays the title menu.  
22. CLEAR Button [pages 21-23]  
39. COAXIAL digital audio out Jack (DVD Audio  
Only)  
Resets a setting.  
23. DISPLAY Button  
Connect to the digital input of an external  
amplifier or decoder.  
TV Mode:  
Press to display the channel number on the  
screen. If you press it again, the channel number  
will disappear.  
40. ANT. in Jack  
Connect to an antenna, cable system, or satellite  
system.  
DVD Mode: [page 25]  
Displays the current status on the TV screen for  
checking purposes.  
41. DC 13.2V Jack  
Connect to the Car Battery Cord.  
24. SEARCH MODE Button [page 21]  
Press to locate a desired point.  
INSTALLING THE BATTERIES  
25. AUDIO Button [page 24]  
Press to select a desired audio language or sound  
mode.  
1)Open the battery compartment cover by pressing the  
cover on the remote unit in the direction of the arrow.  
2)Insert 2 “AA” penlight batteries into the battery  
compartment in the direction indicated by the  
polarity (+/-) markings.  
26. SUBTITLE Button [page 24]  
Press to select a desired subtitle language.  
27. REPEAT Button [page 22]  
Repeats playback of the current disc, title, chapter  
or track.  
3)Replace the cover.  
28. ANGLE Button [page 24]  
NOTES  
Press to change the camera angle to see the  
¡Do not mix alkaline and manganese batteries.  
¡Do not mix old and new batteries.  
EN  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
0C28  
PREPARATION FOR USE  
ANTENNA/CABLE CONNECTIONS  
From Cable System or  
Satellite Box or  
Cable Box  
(Not supplied)  
VHF/UHF Antenna  
(Not supplied)  
OUT  
IN  
Satellite Dish  
VHF Antenna  
(Not supplied)  
UHF Antenna  
(Not supplied)  
From  
Cable System  
DC 13.2V  
ANT.  
L
AUDIO OUT  
R
COAXIAL  
VHF/UHF  
Combiner  
(Not supplied)  
or  
or  
ANT.  
or  
75-ohm Coaxial  
Cable (Not supplied)  
Flat twin-lead cable  
[Fig. 4]  
Note to CATV system installer:  
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides  
guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding  
system of the building as close to the point of cable entry as practical.  
Bent pin  
NOTE:  
Before plugging the an antenna into the ANT. IN jack of the TV/DVD, check that  
the pin is not bent. If it is bent, straighten the pin as illustrated, then plug the pin  
into the ANT. IN jack of the TV/DVD.  
Cable  
Plug  
(Needs to be straightened)(Straight pin)  
VHF/UHF COMBINED ANTENNA  
A VHF UHF 75 ohm combination antenna can be  
connected to ANT terminal.  
CABLE WITH CONVERTER/DESCRAM-  
BLER BOX OR SATELLITE BOX  
If your cable service supplies you with a converter  
box or if you use a satellite system, you can use the  
basic connection shown here.  
Channel selection must be made with the converter  
box or satellite box. This means that channels cannot  
be changed using the TV/ DVD Remote Control.  
TO VIEW A SCRAMBLED/UNSCRAMBLED  
CHANNEL  
1.Set the TV/DVD channel selector to the output  
channel of the Cable Converter Box or Satellite  
Box. (Ex. CH3)  
VHF/UHF SEPARATE ANTENNAS  
In some areas it will be necessary to use an outdoor  
antenna.  
CABLE WITHOUT CONVERTER/  
DESCRAMBLER BOX  
Use this connection if your cable system connects  
directly to your TV/DVD without a converter box.  
Use the TV/ DVD Remote Control to select channels.  
2.Select the channel to view at your Cable Converter  
Box or Satellite Box.  
INDOOR ANTENNA  
Indoor Antenna  
(Supplied)  
The Indoor Antenna (supplied) is detachable. Insert the stem of the antenna into the  
hole on the upper-back portion of the TV/DVD. Connect the Indoor Antenna to the  
TV/DVD as shown in the diagram. For the best reception, fully extend the Indoor  
Antenna and make the necessary adjustments. (Avoid touching the top section when  
adjusting.)  
Flat twin-lead cable  
Matching  
Adapter  
(Supplied)  
NOTE:  
The connection of an Indoor antenna may not always give acceptable TV reception.  
D
C
1
3
.
2
V
ANT.  
L
AUDIO OUT  
R
COAXIAL  
ANT.  
[Fig. 5]  
EN  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
0C28  
CONNECTING TO EXTERNAL INPUT JACKS  
When you watch a program recorded on an another  
[Front of the TV/DVD]  
source (VCR or video camera), use the audio/video  
input jacks on the front of the TV/DVD.  
Connect the audio/video output  
VIDEO  
L
AUDIO  
R
POWER  
[Another source]  
To the audio  
output jacks  
jacks of another source to the  
AUDIO L/R and VIDEO jacks of  
this TV/DVD. Then press SELECT  
until "AUX" appears on the screen.  
NOTE:  
AUX  
Audio/Video  
cables  
(not supplied)  
VIDEO  
L
AUDIO  
R
When you connect a monaural VCR (another  
etc.  
source) to this TV/DVD, connect the Audio output  
jack of the monaural VCR (another source) to the  
AUDIO L jack of this TV/DVD. The audio will  
output in both L and R channel equally.  
To the video  
output jack  
[Fig. 6]  
MOBILE CONNECTION  
WARNING:The driver should never watch the TV/DVD while operating a motor vehicle.  
CAUTION:  
When used in moving vehicle, be sure that the unit is secure at all the times to prevent injury.  
Consult a professional installer.  
If you use the TV/DVD with the vehicles engine off, recharge the vehicles battery after about  
every 4 hours of use to prevent it from running down. After you finish using the TV/DVD be sure  
you unplug the car-battery cord from the cigarette-lighter socket.  
Do not use this TV/DVD while driving.  
Do not leave this TV/DVD in a car.  
This TV/DVD is not designed for use in a car.  
NOTES:  
1) The supplied indoor antenna is adequate when  
your vehicle is stationary. For best reception on  
the road, use a high-quality VHF/UHF mobile TV  
antenna.  
2) Attach the car battery cord to the DC13.2V(12V)  
connector on the back of the TV/DVD. Then, con-  
nect the other end to your vehicle’s cigarette-  
lighter socket.  
Be sure your vehicle has a 13.2-volt (12-volt), neg-  
ative-ground electrical system.  
Be sure you use only the supplied car battery cord.  
Using another cord could damage the TV/DVD.  
Be sure the socket is free of ashes and other debris.  
Be sure to push the car battery cord’s plug com-  
pletely into the cigarette-lighter socket.  
Always unplug the car battery from the cigarette-  
lighter socket before you unplug it from the  
TV/DVD.  
To the vehicle's  
cigarette-lighter socket  
VHF/UHF Combination  
Mobile Antenna  
(Not supplied)  
You must disconnect the car battery cord from the  
TV/DVD before you can use the AC power.  
Be sure to replace the fuse with only the same type,  
6A, 250V.  
Car battery cord  
(Supplied)  
ANT.  
DC 13.2V  
DC13.2V  
ANT.  
AUDIO OUT  
R
COAXIAL  
EN  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
0C28  
CONNECTING TO A STEREO SYSTEM  
Stereo system  
DC 13.2V  
L
AUDIO OUT  
R
ANT.  
L
AUDIO OUT  
R
COAXIAL  
COAXIAL  
To ANALOG AUDIO INPUT jacks  
To Right (red) and Left (white)  
AUDIO OUT jacks  
[Fig. 7]  
NOTES:  
Be sure to turn off the power to all components in the system before connecting another component.  
Refer to the Owner's Manuals for your, stereo system and any other components to be connected to the  
TV/DVD.  
The monaural sound is output from the stereo system when the TV/DVD is in the TV mode.  
CONNECTING TO AN AMPLIFIER EQUIPPED WITH DIGITAL  
INPUT JACKS, MD DECK OR DAT DECK (for DVD only)  
Use an audio coaxial digital cable available at retail for the audio connections.  
Amplifier equipped with digital  
input jacks, MD deck,  
DAT deck, etc.  
DC 13.2V  
L
AUDIO OUT  
R
ANT.  
L
AUDIO OUT  
R
COAXIAL  
COAXIAL  
To COAXIAL DIGITAL  
AUDIO INPUT jack  
To DIGITAL AUDIO OUT  
(PCM/BITSTREAM)  
COAXIAL jack  
(only DVD AUDIO OUT)  
[Fig. 8]  
NOTES:  
The audio source on a disc in a 5.1 channel Dolby Digital surround format cannot be recorded as digital  
sound by an MD or DAT deck.  
Be sure to turn off the power to all components in the system before connecting another component.  
Refer to the Owner's Manuals for the components to be connected to the TV/DVD.  
Set DOLBY DIGITAL to OFF for audio output in the setup mode. Playing a TV/DVD using incorrect set-  
tings may generate noise distortion, and may also damage the speakers. (See page 27 to set DOLBY  
DIGITAL to OFF.)  
EN  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
0C28  
CONNECTING TO A DOLBY DIGITAL DECODER (for DVD)  
If using this TV/DVD to play a DVD disc in a 5.1 channel Dolby Digital surround format, the TV/DVD out-  
puts a DOLBY DIGITAL Data stream from its COAXIAL digital audio out jack. By hooking the player up to  
a Dolby Digital decoder, you can enjoy a more convincing, realistic ambience with powerful and high-quality  
surround sound as enjoyed in movie theaters.  
Use audio coaxial digital cables available at retail for the audio connections.  
Center  
speaker  
Front speaker  
(left)  
Front speaker  
(right)  
DC 13.2V  
L
Dolby Digital decoder  
To COAXIAL DIGITAL  
AUDIO INPUT jack  
AUDIO OUT  
R
ANT.  
L
AUDIO OUT  
R
COAXIAL  
COAXIAL  
Subwoofer  
Surround  
speaker  
(left)  
Surround  
speaker  
(right)  
To DIGITAL AUDIO OUT  
(PCM/BITSTREAM)  
COAXIAL jack  
[Fig. 9]  
NOTES:  
Be sure to turn off the power to all components in the system before connecting another component.  
Refer to the Owner's Manuals for the components to be connected to the TV/DVD.  
If connected to a Dolby Digital decoder, set DOLBY DIGITAL to ON for audio output in the setup mode.  
(See page 27 to set DOLBY DIGITAL to ON.)  
Unless connected to a Dolby Digital decoder, set DOLBY DIGITAL to OFF for audio output in the setup  
mode. Playing a TV/DVD using incorrect settings may generate noise distortion, and may also damage the  
speakers.  
Manufactured under license from Dolby Laboratories. Dolbyand the double-D symbol are  
trademarks of Dolby Laboratories.  
EN  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
0C28  
TV SECTION  
SET UP FOR USE  
You can program the tuner to scan all the channels you receive in your area.  
NOTE: Channel memory programming is NOT needed when connected to a cable box or satellite box. Just  
select the TV/DVD channel selector to the output channel of the cable box or satellite box (Ex CH3). Then  
select the channel to be viewed on the Cable Box or Satellite Box.  
CHANNEL SET UP FOR THE  
FIRST TIME  
DELETING (OR ADDING)  
CHANNEL  
TV  
TV  
The channels you no longer receive or seldom watch  
can be deleted from the memory. (Of course, you can  
add the deleted channel into the memory again.)  
1 Plug in the TV/DVD power cord  
Plug the TV/DVD power cord into a  
standard AC outlet.  
NOTE:  
- TV SETUP -  
1 Select CHANNEL SET UP”  
Press SETUP on the remote control.  
Press K or L to point to “CHAN-  
NEL SET UP”.  
If some digits appear in the corner of  
the screen, press POWER without  
unplugging the power cord.  
B
CHANNEL SET UP  
LANGUAGE [ENGLISH]  
2 Turn on the TV/DVD  
Press POWER to turn on the TV/DVD.  
Then, press ENTER.  
2 Select ADD/DELETE CH”  
Press K or L to point to  
“ADD/DELETE CH”.  
CHANNEL SET UP –  
B
ADD / DELETE CH (TV)  
AUTO PRESET  
3 Select the On Screen  
Language  
Press K or L to point to “LAN-  
GUAGE”.  
SET UP –  
LANGUAGE  
B
Then, press ENTER.  
[ENGLISH] ESP  
FRA  
AUTO PRESET  
Then, press ENTER to select  
“ENGLISH” or “ESP”=Spanish or  
“FRA” =French. “[ ]” indicate the selected language.  
3 Enter the desired channel number  
Press K or L until your desired  
channel number appears. (You can  
also use Number or CH. K/L to  
enter it.) (Example: CH8)  
08  
SET UP –  
4 Begin auto preset  
Press K or L to point to “AUTO  
ADD / DELETE  
LANGUAGE  
[ENGLISH] ESP  
FRA  
PRESET”. Then, press ENTER.  
The tuner scans and memorizes all  
active channels in your area.  
B
AUTO PRESET  
4 Delete (or add) it from (into) memory  
Press ENTER. The channel number changes to light  
red. The channel is deleted from memory.  
NOTES:  
The TV/DVD distinguishes between standard TV  
channels and cable(CATV) channels.  
Added channel: Light blue.  
Deleted channel: Light red.  
The TV/DVD may memorize TV channels as  
CATV channels if reception conditions is poor. If  
this happens, try AUTO PRESET action again  
when reception conditions are better. See “CHAN-  
NEL SET UP AGAIN” on page 15.  
To delete another channel, repeat steps [3] and [4].  
If you press ENTER again, the channel is memo-  
rized again.  
5 After scanning  
5 Exit the channel setup mode  
Press SETUP on the remote control to returns to TV  
mode.  
NOTE: To confirm that channel(s) has been deleted  
or added, press CHANNEL(CH.) K or L.  
The tuner stops on the lowest memorized channel.  
If you want to recall the selected channels, you can  
select the desired channel directly with Number or  
CHANNEL(CH.) K or L.  
EN  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
0C28  
CHANNEL SET UP AGAIN  
TV  
- TV SETUP -  
1 Select CHANNEL SET UP”  
Press SETUP on the remote control.  
Press K or L to point to “CHAN-  
NEL SET UP”.  
B
CHANNEL SET UP  
LANGUAGE [ENGLISH]  
Then, press ENTER.  
2 Begin auto preset  
CHANNEL SET UP –  
Press K or L to point to “AUTO  
PRESET”. Then, press ENTER.  
The tuner scans and memorizes all  
the active channels in your area.  
NOTES:  
ADD / DELETE CH (TV)  
AUTO PRESET  
B
The TV/DVD distinguishes between standard TV  
channels and cable(CATV) channels.  
The TV/DVD may memorize TV channels as  
CATV channels if reception conditions is poor. If  
this happens, try AUTO PRESET action again  
when reception conditions are better.  
3 After scanning  
The tuner stops on the lowest memorized channel.  
SELECTING THE LANGUAGE  
TV  
NOTE: This function effects only the language on  
the screen menu and not the audio source.  
- TV SETUP -  
1 Select LANGUAGE”  
Press SETUP on the remote control.  
Press K or L to point to “LAN-  
GUAGE”.  
CHANNEL SET UP  
LANGUAGE [ENGLISH]  
B
Then, press ENTER to select  
“ENGLISH” or “ESPAÑOL”=  
Spanish or “FRANÇAIS”= French.  
2 Exit the Language mode  
Press SETUP on the remote control to return to TV  
mode.  
NOTE: If Spanish or French is selected accidentally,  
1)Press SETUP on the remote control.  
2)Press K or L to point to “IDIOMA [ESPAÑOL]”  
or “LANGAGE” [FRANÇAIS].  
3)Press ENTER to select your desired language.  
4)Press SETUP to exit.  
EN  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
0C28  
TV OPERATION  
WATCHING A TV PROGRAM  
PICTURE CONTROL  
TV  
TV  
The TV/DVD’s picture controls – BRIGHT, CON-  
TRAST, COLOR, TINT and SHARPNESS – are  
preset to factory specifications. Although they are  
usually the best, you may need to make some further  
adjustments for a natural looking image.  
1 Turn on the TV/DVD  
Press POWER to turn on the TV/DVD.  
2 Select the channel number  
Press CHANNEL(CH.) K or L to select your desired  
channel number or press Number on the remote con-  
trol.  
Make sure ...  
TV/DVD power must be turned on.  
Note for using the Number on the remote control:  
¡When selecting cable channels which are higher  
than 99, press +100 first, then, press the last two  
digits. (Example: to select channel 125, first press  
“+100” then press “2” and “5”).  
1 Select PICTURE CONTROL”  
Press PICTURE on the remote control.  
¡You must precede single-digit channel numbers  
with a zero (For example: 02, 03, 04 and so on).  
Remember:  
¡If the TV/DVD is connected to a cable box or  
satellite box, the TV/DVD must be on CH3 or  
CH4, then the channel to be viewed must be select-  
ed on the cable box or satellite box.  
2 Select item you want to adjust  
Press K or L until desired control is displayed.  
BRIGHT  
CONTRAST  
COLOR  
TINT  
BRIGHT  
P
P
P
P
P
P
P
C
P
P
P
P
P
P
P +  
SHARPNESS  
3 Adjust sound  
X
Y
Press VOLUME(VOL.) or to  
3 Adjust the picture control  
adjust the volume.  
Press B or s to adjust to your desired level within  
VOLUME 20  
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
5 seconds.  
NOTE:  
NOTE:  
At step 3, the picture adjustment display will disap-  
If you press the CHANNEL(CH.) o or p in the  
DVD mode, you can change the TV channels.  
Even if you turn off the TV/DVD in the DVD  
mode, when you turn it on again, it will go into the  
TV mode.  
pear from the TV screen after about 5 seconds  
unless you press any buttons, even though you may  
not be finished. In this case, repeat from step [1].  
s
B
BRIGHT  
to decrease  
brightness  
to decrease  
contrast  
to increase  
brightness  
to increase  
contrast  
DEGAUSSING  
Magnetism from nearby appliances and speakers  
might affect the color of the TV picture.  
If this happens, move this unit away from the appli-  
ance. If the color is still not correct, disconnect power  
cord from AC outlet then reconnect it after 30 minutes.  
CONTRAST  
COLOR  
TINT  
SHARPNESS to soft  
to pale  
to brilliant  
to purple  
to green  
to clear  
If there is a power failure of any kind, the unit will  
retain its memory for this feature.  
EN  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
0C28  
SLEEP TIMER  
TV  
he Sleep Timer function enables you to shut off the power  
T
without pressing POWER after a desired time period.  
1 Set SLEEP TIMER”  
Press SLEEP on the remote control.  
You may change the sleep time  
with pressing SLEEP on the remote  
control repeatedly. The timer is set  
SLEEP 120 MINUTE  
up to 120 minutes, 30 minutes each  
time SLEEP is pressed.  
To cancel the sleep timer:  
Press SLEEP repeatedly until "SLEEP 0 MINUTE"  
is displayed.  
NOTES:  
When you disconnect the unit from the AC outlet,  
or if you have a power failure, the sleep time will  
be lost.  
To view the time left for sleep timer press SLEEP  
once when SLEEP display disappears. After 10  
seconds, display will disappear again.  
EN  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
0C28  
DVD SECTION  
ABOUT THE DISCS  
PLAYABLE DISCS  
DISC TYPES  
The following discs can be played back on this TV/DVD.  
[
]
DVD  
Data on a DVD is divided into sections called "titles", and  
then into subsections called "chapters", each of which is  
given a title or chapter number. Playback conditions are  
preset on some DVD video discs, and these playback con-  
ditions take priority over user operations on this player. If  
a function you selected does not run as desired, refer to  
the manual accompanying the disc.  
¡
¡
¡
¡
¡
¡
DVD video  
DVD+R/RW*  
CD-R/RW*  
DVD-R/RW*  
Audio CD  
MP3*  
* Depending on the types or the writing method of the  
medium some discs can not be played.  
• Some DVD-R/RW, DVD+R/RW, or CD-R/RW discs  
made on personal computers, or on DVD recorders may  
not be played back properly due to the factors such as  
scratches, dirt or special properties of the disc.  
• Discs made on personal computers may not be played  
back properly due to the different environment or the  
settings of the application you use. We recommend  
always to use the standardized, rightly formatted discs.  
(Please contact the sales agency for more detail).  
Example  
Title 1  
Title 2  
Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1 Chapter 2  
This player conforms to the NTSC color system. You can-  
not play discs recorded in other color systems such as  
PAL or SECAM.  
[
]
AUDIO CD  
Data on an audio CD is divided into sections called  
“tracks”, each of which is given a track number.  
¡Some discs include region codes as shown below.  
Example  
Track 1  
Track 2  
Track 3  
Track 4  
Track 5  
Track 6  
¡The number inside the symbol refers to a region of the  
world, and a disc encoded in a specific region format  
can only be played back on TV/DVD with the same  
region code.  
The following discs cannot be played back on this  
TV/DVD.  
[
]
MP3  
Data on an MP3 is divided into sections called "groups",  
and then into subsections called "tracks", each of which is  
given a group or track number.  
¡
DVD with region codes other than 1 or ALL.  
¡
¡
DVD-ROM  
Example  
DVD-RAM (Never play back, otherwise malfunc-  
tion may result.)  
Group 1  
Group 2  
¡
¡
¡
¡
¡
Track 1  
Track 2  
Track 3  
Track 4  
Track 1  
Track 2  
CD-ROM  
VSD  
CDV (Only plays back the audio part.)  
CD-G (Only plays back the sound.)  
CD-I (Never play back, otherwise malfunction  
may result.)  
¡
¡
SACD  
Photo CD (Never play back, otherwise malfunc-  
tion may result.)  
¡
Video CD (Never play back, otherwise malfunc-  
tion may result.)  
Any other discs without compatibility indications.  
EN  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
0C28  
PLAYING A DISC  
BASIC PLAYBACK  
GENERAL FEATURES  
DVD may contain menus to navigate the disc and  
access special features. Press appropriate numerical  
key or use Arrow (L/K/B/s) to highlight your selec-  
tion in the DVD main menu and press ENTER to con-  
firm.  
DVD-V  
CD  
Getting started  
¡Turn on the power of amplifier and any other com-  
ponents, if necessary.  
NOTES  
¡Select DVD mode by pressing SELECT on the  
remote control. Then, press PLAY or OPEN/CLOSE  
before you operate the DVD functions.  
1
Press POWER.  
¡The power will turn on.  
2
3
Press OPEN/CLOSE to open disc loading  
tray.  
¡Unless stated, all operations described are based on  
remote control use. Some operations can be carried  
out using the menu bar on the TV screen.  
Place the chosen disc in the tray, with the  
label facing up.  
DISC MENU  
DVD-V  
1
Press DISC MENU.  
¡The DVD main menu will appear.  
2
3
If the feature is not available,  
may appear on the TV screen.  
symbol  
4
Press PLAY.  
¡The tray will close automatically, and playback will  
then start from the first chapter or track of the disc.  
If the playback does not start automatically, press  
PLAY.  
If disc menu is available on the disc, audio  
language, subtitle options, chapters for the  
title and other options will appear for selec-  
tion.  
¡When you playback the DVD which a title menu is  
recorded, it may appear on the screen. In this case,  
refer to “TITLE MENU”.  
4
Press Arrow (L/K/B/s) to select an item,  
and ENTER to confirm selection.  
5
Press STOP to stop playback.  
TITLE MENU  
NOTES  
DVD-V  
¡When the DVD mode has been switched to the TV  
mode, the DVD mode shuts down first and then TV  
picture and sound appears in about 4 seconds.  
Similarly, when POWER is pressed to turn off in the  
DVD mode, this mode shuts down first and then the  
TV/DVD’s power is turned off.  
¡A “prohibited icon” may appear at  
the top-right on the TV screen dur-  
ing operation, warning that a pro-  
hibited operation has been encoun-  
1
Press TITLE.  
¡The title menu will appear.  
2
3
If the feature is not available,  
may appear on the TV screen.  
symbol  
Press Arrow (L/K/B/s) to select an item,  
and ENTER to confirm selection.  
tered by the DVD or the disc.  
¡With DVDs that use titles for playback program sig-  
nals, playback may start from the second title, or it  
may skip these titles.  
¡During the playback of a two layered disc, pictures  
may stop for a moment. This happens when the 1st  
layer switches to the 2nd layer. This is not a mal-  
function.  
CALLING UP A MENU SCREEN  
DURING PLAYBACK  
For DVD-Vs  
¡Press DISC MENU to call up the DVD menu.  
¡Press TITLE to call up the title menu.  
NOTE  
¡Contents of menus and corresponding menu opera-  
tions may vary between discs. Refer to the manual  
accompanying the disc for details.  
EN  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
0C28  
SLOW FORWARD /  
SLOW REVERSE  
RESUME  
DVD-V  
CD  
DVD-V  
1
During playback, press STOP.  
¡Resume message will appear on the TV screen.  
1
2
3
During playback, press PAUSE.  
Press FWD g or REV h .  
2
Press PLAY, playback will resume from the  
point at which playback was stopped.  
Press FWD g or REV h repeatedly to  
select the required speed: 1/16, 1/8, 1/2 of  
the normal playback.  
¡To cancel resume, press STOP twice.  
¡If turn off the TV/DVD, resume function will be  
cancelled.  
4
To return to normal playback, press PLAY.  
Note for using buttons on the main unit:  
Press PAUSE, then, press and hold down the SKIP G/  
SEARCHg or SKIPH /SEARCHh on the  
TV/DVD for a few seconds to begin Search in 1/16  
speed of the normal playback. Press and hold down  
again to change speed to 1/8. Repeat this procedure to  
change to 1/2.  
PAUSE  
DVD-V  
CD  
1
During playback, press PAUSE.  
¡Playback will pause and sound will be muted.  
2
To continue playback, press PLAY.  
ZOOM  
STEP BY STEP PLAYBACK  
DVD-V  
DVD-V  
The Zoom function allows you to enlarge the video  
image and to pan through the enlarged image.  
1
During playback, press PAUSE.  
¡Playback will pause and sound will be muted.  
1
Press ZOOM during playback.  
¡Playback will continue.  
2
3
The disc goes forward by one frame each  
time PAUSE is pressed.  
2
Press ZOOM repeatedly to select the  
required zoom factor: ZOOM1, ZOOM2,  
ZOOM3, or OFF.  
To exit step by step playback, press PLAY.  
FAST FORWARD/REVERSE  
SEARCH  
3
4
Use the Arrow (K/L/s / B) to move the  
zoomed picture across the screen.  
DVD-V  
CD  
MP3  
To exit zoom mode, press ZOOM to OFF.  
NOTES  
1
During playback, press FWD g or REV  
repeatedly to select the required forward or  
reverse speed: x2, x8, x50, x100.  
h
¡Zooming function does not work while disc menu is  
shown.  
¡Zooming function is not available on some discs.  
¡For audio CDs, the speed is fixed at ×16.  
¡For MP3, the speed is fixed at ×8.  
2
To return to normal playback, press PLAY.  
Note for using buttons on the main unit:  
During playback, press and hold down the SKIP G /  
SEARCHg or SKIPH /SEARCHh on the  
TV/DVD for a few seconds to begin Search in x2  
speed. Press and hold down again to change speed to  
x8. Repeat this procedure to change to x50 and x100.  
EN  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
0C28  
SEARCH FUNCTION  
TRACK SEARCH  
TIME SEARCH  
CD  
DVD-V  
CD  
There are three ways to begin playback on an Audio  
CD at a specific Track.  
1
2
During playback, press SEARCH MODE  
three times (CD: twice) to display the Time  
Search on the TV screen.  
Using Number on the remote control  
Within 30 seconds, enter a desired disc  
time using Number on the remote control.  
1
Press Number to enter the desired Track  
number.  
¡Playback will start at the specified time.  
¡Press CLEAR to erase the incorrect input.  
¡Playback will start at the selected track.  
¡For single digit tracks (1-9), press a single number  
(eg. track 3, press 3).  
¡To play track 26, press +10, 2, 6.  
MARKER SETUP SCREEN  
DVD-V  
CD  
Using SEARCH MODE  
1
Press SEARCH MODE.  
¡The track search display appears.  
Use markers to memorise your favorite places on a  
disc.  
2
Within 30 seconds, select a desired track  
number using Number on the remote control.  
1
Press SEARCH MODE four times (CD: three  
times) during playback.  
¡For single digits press 0 first.  
¡Playback will start at the selected track.  
¡The display screen and Markers will appear on the  
TV screen.  
Using SKIP  
H
G
During playback, press SKIP G to move the next  
track. Press it repeatedly to skip subsequent tracks.  
Press SKIP H to go back to beginning of the current  
track. Press it repeatedly to go to the previous tracks.  
¡If SKIP is pressed while the playback is paused, the  
playback will be paused again after skipping to the  
next track.  
2
3
Press Arrow (s /B) to select 1, 2, 3, 4, 5, 6,  
7, 8, 9, or 10 and ensure that - : - - : - -”  
appears in the display.  
When reaches the desired point, press  
ENTER.  
¡The Title or Track and elapsed playing time will  
appear in the TV screen.  
NOTE  
¡SKIP  
H
G are not available when playback is  
stopped.  
4
To return to the Marker later, press SEARCH  
MODE four times (CD: three times) during  
playback and Arrow (s /B) to choose the  
desired marker, then press ENTER.  
TITLE / CHAPTER SEARCH  
NOTES  
DVD-V  
¡Opening the disc tray or turning off the power or  
select AC at step 2 and press ENTER will erase all  
Markers.  
¡To clear a marker, using Arrow (s /B), position the  
cursor on to the marker number to be cleared and  
press CLEAR.  
1
Press SEARCH MODE once for the Chapter  
search, twice for the Title search during  
playback.  
/2  
¡You can mark up to 10 points.  
5
Press SEARCH MODE or RETURN to exit.  
2
Enter the desired chapter/title number using  
Number on the remote control.  
¡Playback will start at the selected Chapter or Track.  
¡Press CLEAR to erase the incorrect input.  
¡For single digits press 0 first.  
EN  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
0C28  
SPECIAL PLAYBACK FUNCTION  
REPEAT  
PROGRAM  
REPEAT is available only during playback.  
CD  
REPEAT TITLE / CHAPTER  
You may determine the order in which tracks will play.  
DVD-V  
1
In stop mode, press MODE.  
¡The PROGRAM screen will appear.  
To activate the repeat function, press REPEAT  
during playback.  
¡The repeat mode changes as described below every  
time you press the button.  
2
Press L or M to select a track, then press  
ENTER.  
CHAPTER  
(current chapter repeat) (current title repeat)  
TITLE  
OFF  
(repeat off)  
¡Press CLEAR to erase the  
most recently entered pro-  
gram.  
TOTAL  
NOTES  
¡Repeat Title/Chapter is not available with some  
scenes.  
¡The REPEAT setting will be cleared when moving  
to other title or chapter.  
3
4
Repeat step 2 until you have selected all the  
tracks you want to play in the program.  
Press PLAY to play the programmed tracks.  
NOTES  
REPEAT TRACK  
CD  
¡While the program is being played back, the STOP  
works as follows.  
¡Press STOP once and then PLAY again, playback  
will restart from the point where STOP was pressed.  
(Program continued)  
¡Press STOP twice and then PLAY again, playback will  
restart from the track in the usual way. (Program cleared)  
¡Up to 99 programs can be entered.  
¡If you like to repeat the current track in the program,  
To activate the repeat function, press REPEAT  
during playback.  
¡The repeat mode changes as described below every  
time you press the button.  
TRACK  
(current track repeat)  
ALL  
OFF  
(repeat off)  
(entire disc repeat)  
press REPEAT repeatedly until  
TRACK appears  
during playback. If you like to repeat the entire pro-  
NOTES  
gram press REPEAT repeatedly until  
appears during playback.  
ALL  
¡Repeat setting will be cleared when moving to other  
track.  
¡Repeat playback does not function during repeat A-  
B playback.  
RANDOM PLAYBACK  
REPEAT A-B  
CD  
DVD-V CD  
This shuffles the playing order of tracks instead of  
playback in the sequence.  
1
2
Press REPEAT A-B at your chosen starting  
point.  
A- appears briefly on the TV screen.  
¡
¡
1
In stop mode, press MODE twice.  
¡RANDOM screen appears.  
RANDOM  
Press REPEAT A-B again at your chosen  
end point.  
CD [AUDIO]  
TOTAL 0:45:55  
RANDOM PROGRAM  
- - no indication - -  
A-B appears briefly on the TV screen, and the  
repeat sequence begins.  
PLAY  
3
To exit the sequence, press REPEAT A-B.  
NOTES  
¡The repeat A-B section can only be set within the cur- NOTE  
rent title (for DVDs), or current track (for audio CDs). ¡If you like to repeat the current track in the random  
2
Press PLAY to start random playback.  
¡Repeat A-B is not available with some scenes in DVD.  
¡To cancel the A point which was set, press CLEAR.  
¡Repeat A-B playback does not function during title,  
chapter, track or all repeat playback.  
selection, press REPEAT repeatedly until  
TRACK appears during playback. If you like to  
repeat the entire random selection press REPEAT  
repeatedly until  
ALL appears during playback.  
EN  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
0C28  
PLAYING A MP3 DISC  
MP3 PLAYBACK  
TRACK SELECTION  
MP3  
MP3  
When a CD with MP3 files is in the TV/DVD, the  
MP3 menu will appear on the TV screen in stop mode.  
1
Press SEARCH MODE during playback.  
¡The FILE LIST will appear.  
1
In stop mode, press Arrow (K/L) to select  
the desired group track.  
2
Select a desired track using Arrow  
(K/L/s/B).  
¡If a group is selected, press  
or ENTER to go on to the  
track selection screen. Press  
Arrow (K /L ) to choose a  
B
¡Press B when you want to go to the next hierarchy.  
¡Press s when you want to go back to the previous  
hierarchy.  
track, then press ENTER.  
¡If a track is selected, press  
ENTER to start playing  
tracks. Starting from the one you’ve just chosen the  
subsequent tracks will be played.  
¡Choose FIRST PLAY to start playback from the  
beginning of the listed tracks.  
3
Press PLAY to start playback.  
NOTES  
¡Press SEARCH MODE to exit.  
¡Some selections may take a while to be recognized.  
PROGRAM  
¡Press TITLE to return to the first item.  
MP3  
2
Press STOP to stop playback.  
NOTES  
This feature allows you to program an MP3 disc to  
play in a desired sequence.  
¡Folders are known as Groups; files are known as  
Tracks.  
¡MP3 files are accompanied by  
3
icon.  
¡Maximum of 255 folders can be recognized.  
¡Maximum of 256 files can be recognized.  
¡Up to 8 hierarchies can be created.  
1
In stop mode, press MODE.  
¡The PROGRAM screen will appear.  
This player recommends the use of files recorded at  
the below specifications:  
¡Sampling frequency: 44.1kHz or 48kHz  
¡Constant bit rate: 112kbps ~ 320kbps.  
2
Select a desired track using Arrow  
(K/L/s/B). Then, press ENTER.  
¡Press B when you want to go to the next hierarchy.  
¡Press s when you want to go back to the previous  
hierarchy.  
¡Press CLEAR to erase the most recently entered pro-  
gram.  
3
Repeat step 2 until you have selected all the  
Tracks you want to play in the program.  
4
Press PLAY to start programmed playback.  
RANDOM PLAYBACK  
MP3  
1
In stop mode, press MODE twice.  
¡RANDOM screen appears.  
2
Press PLAY to start random playback.  
EN  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
0C28  
CHANGING THE SETTINGS  
SUBTITLE LANGUAGE  
CAMERA ANGLE  
DVD-V  
DVD-V  
The DVD allows you to select a language for subtitles Some DVD discs contain scenes which have been shot  
during DVD disc (if available) playback. simultaneously from various angles. You can change  
the camera angle when the (  
screen.  
) icon appears on the  
1
2
Press SUBTITLE during playback.  
Press SUBTITLE repeatedly to select your  
desired subtitle language.  
1
Press ANGLE during playback.  
¡The selected angle will be displayed on the display  
¡The subtitle language will be displayed on the dis-  
play bar at the top of the screen.  
bar at the top of the screen.  
2
Press ANGLE repeatedly to select your  
desired angle.  
3
To turn off subtitles, press SUBTITLE  
repeatedly until OFF appears.  
NOTES  
BLACK LEVEL SETTING  
¡
Some discs allow audio language setting/subtitle language  
setting on the disc menu. (Operation varies between discs,  
so refer to the manual accompanying the disc.)  
DVD-V  
¡If the desired language is not shown after pressing  
SUBTITLE several times, the disc does not have  
subtitles in that language.  
Adjust the Black Level Settings to make the black  
parts of the picture brighter.  
¡If you choose a Language that has a 3 letter language  
code, the code will be displayed every time you  
change the Subtitle language setting. If you choose  
any other languages, ‘---’ will be displayed instead.  
(Refer to page 26.)  
1
Press MODE during playback.  
ON  
AUDIO LANGUAGE  
2
Press ENTER to switch ON/OFF.  
ON: Makes the dark parts brighter.  
DVD-V  
OFF: Shows the original picture as recorded.  
The TV/DVD allows you to select a language during  
DVD disc (if multi language available) playback.  
3
Press MODE twice or RETURN to exit.  
VIRTUAL SURROUND  
1
2
Press AUDIO during playback.  
Press AUDIO repeatedly to select your  
desired language.  
DVD-V  
CD  
MP3  
NOTE  
You can enjoy stereophonic visual space on your exist-  
ing stereo system.  
¡Pressing AUDIO may not work on some DVDs with  
multiple audio languages (e.g. DVDs which allow  
audio language setting on the disc menu).  
1
Press MODE twice (CD/MP3: once) during  
playback.  
STEREO SOUND MODE  
OFF  
CD  
2
3
Press ENTER to set it 1 (Natural effect) or 2  
(Emphasized effect) or OFF.  
1
Press AUDIO repeatedly during playback to  
select between STEREO, L-CH or R-CH.  
¡STEREO - both right and left channels are active  
(stereo)  
L-CH - only left channel is active  
R-CH - only right channel is active  
NOTE  
Press MODE or RETURN to exit.  
NOTE (for CD play only)  
¡Virtual Surround will not be effective if the sound  
mode is set to something other than STEREO.  
¡If the Virtual Surround setting is ON, the sound  
mode will be fixed to STEREO, and can not be  
changed.  
EN  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
0C28  
THE ON-SCREEN INFORMATION  
DVD-V  
CD  
MP3  
You can check the information about the current disc by pressing DISPLAY on the remote control.  
For DVD-Vs  
For audio CDs  
1
Press DISPLAY during playback to show  
current Chapter.  
1
Press DISPLAY during playback to show  
the current Track.  
¡The elapsed and remaining  
playing time of the current  
chapter will be displayed.  
¡The elapsed and remaining playing time of the cur-  
rent track will be displayed.  
9/49  
0:00:00 -0:00:00  
2
Press DISPLAY again to show current Total  
Track.  
2
Press DISPLAY again to show current Title.  
¡The elapsed and remaining playing time of the cur-  
¡The elapsed and remaining playing time of the cur-  
rent total track will be displayed.  
rent title will be displayed.  
3
Press DISPLAY again.  
¡The BIT RATE and the current repeat setting will be  
displayed.  
3
Press DISPLAY again to exit the display.  
¡If you are playing a dual layered disc, the layer num-  
ber will also be displayed (L0: Layer 0 is playing.  
L1: Layer 1 is playing).  
For MP3  
1
Press DISPLAY during playback.  
¡The name of the file currently in play will be dis-  
4
Press DISPLAY again to exit the display.  
played.  
2
Press DISPLAY again to show the track  
number, the repeat status, and the playback  
status at the top of the screen.  
¡
will be displayed when repeat play has been  
selected.  
T - indicates Track repeat  
G - indicates Group (folder) repeat  
A - indicates Disc repeat  
3
Press DISPLAY again to exit the display.  
EN  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
0C28  
CHANGING THE DVD SETUP ITEMS  
LANGUAGE SETTING  
Language  
Code Language  
Code  
DVD-V  
A-B  
L-N  
Abkhazian  
Afar  
Afrikaans  
Albanian  
Amharic  
Arabic  
Armenian  
Assamese  
Aymara  
Azerbaijani  
Bashkir  
Basque  
Bengali;Bangla  
Bhutani  
Bihari  
Bislama  
Breton  
4748 Laothian  
4747 Latin  
4752 Latvian;Lettish  
6563 Lingala  
4759 Lithuanian  
4764 Macedonian  
5471 Malagasy  
4765 Malay  
5861  
5847  
5868  
5860  
5866  
5957  
5953  
5965  
5958  
5966  
5955  
5964  
5961  
5960  
6047  
6051  
6061  
Language options are not available with some discs.  
1
Press SETUP twice in STOP mode so that  
the DVD SETUP menu appears.  
¡If the menu does not appear, press PLAY, STOP,  
4771 Malayalam  
4772 Maltese  
4847 Maori  
then SETUP twice.  
5167 Marathi  
4860 Moldavian  
5072 Mongolian  
4854 Nauru  
QUICK SETUP  
TV MODE  
DOLBY DIGITAL ON  
4:3 LETTER BOX  
4855 Nepali  
4864 Norwegian [NOR]  
4853  
5971 Occitan  
4851 Oriya  
Oromo(Afan)  
5759 Panjabi  
4947 Pashto;Pushto  
7254 Persian  
4961 Polish  
5464 Portuguese [POR]  
4965 Quechua  
5047 Rhaeto-Romance  
6058 Romanian [RUM]  
5160 Russian [RUS]  
5161  
5166 Samoan  
Sangho  
5261 Sanskrit  
5256 Scots Gaelic  
5255 Serbian  
Bulgarian  
Burmese  
Byelorussian  
O-R  
6149  
6164  
6159  
6247  
6265  
5247  
6258  
6266  
6367  
6459  
6461  
6467  
2
Press B to select CUSTOM, then press  
C-E  
ENTER.  
Cambodian  
Catalan  
¡CUSTOM mode will appear.  
Chinese [CHI]  
Corsican  
Croatian  
3
Press Arrow (s / B) to select LANGUAGE,  
Czech  
then press ENTER to confirm.  
Danish [DAN]  
Dutch [DUT]  
English [ENG]  
Esperanto  
Estonian  
S
6559  
6553  
6547  
5350  
6564  
6554  
6566  
6660  
6560  
6550  
6555  
6565  
6557  
6558  
6561  
5165  
6567  
6569  
6568  
LANGUAGE  
F-H  
AUDIO  
SUBTITLE  
DISC MENU  
ORIGINAL  
OFF  
ENGLISH  
Faroese  
Fiji  
Finnish [FIN]  
French [FRE]  
Frisian  
5264 Serbo-Croatian  
5271 Sesotho  
5358 Setswana  
5747 Shona  
4
Press Arrow (K/L) to select the next items,  
Galician  
then press ENTER.  
Georgian  
German [GER]  
Greek [GRE]  
Greenlandic  
Guarani  
AUDIO:  
5051 Sindhi  
5158 Singhalese  
5758 Siswat  
5360 Slovak  
¡Sets the audio language.  
SUBTITLE:  
¡Sets the subtitle language.  
DISC MENU:  
Gujarati  
Hausa  
Hebrew  
5367 Slovenian  
5447 Somali  
5569 Spanish [SPA]  
5455 Sundanese  
5467 Swahili  
¡Sets the language for DVD menu.  
Hindi  
Hungarian [HUN]  
I-K  
Icelandic [ICE]  
Indonesian  
Interlingua  
Interlingue  
Inupiak  
Swedish [SWE]  
5
Press Arrow (K/L) to select a setting, then  
5565  
5560 Tagalog  
5547 Tajik  
5551 Tamil  
5557 Tatar  
5347 Telugu  
5566 Thai  
T
press ENTER.  
6658  
6653  
6647  
6666  
6651  
6654  
4861  
6655  
6661  
6665  
6664  
6657  
6669  
¡If OTHER is selected on the AUDIO, SUBTITLE or  
DISC MENU screen, press four-digit number to  
enter the code for the desired language. (Refer to the  
language code list below.)  
¡Only the languages supported by the disc can be  
selected.  
Irish [IRI]  
Italian [ITA]  
Japanese [JPN]  
Javanese  
Kannada  
Kashmiri  
5647 Tibetan  
5669 Tigrinya  
5760 Tonga  
5765 Tsonga  
5757 Turkish [TUR]  
6469 Turkmen  
5771 Twi  
Kazakh  
Kinyarwanda  
Kirghiz  
Kirundi  
6
Press SETUP to exit.  
NOTE  
6460  
U-Z  
¡Language Setting for Audio and Subtitle is not avail-  
able with some discs. Then use the AUDIO and the  
SUBTITLE button. Details are on page 24.  
Korean [KOR]  
Kurdish  
5761 Ukrainian  
5767 Urdu  
Uzbek  
6757  
6764  
6772  
6855  
6861  
4971  
6961  
7054  
5655  
7161  
7267  
Vietnamese  
Volapuk  
Welsh  
Wolof  
Xhosa  
Yiddish  
TO CHANGE THE ON-SCREEN MENUS  
You can access the TV SETUP menu by pressing  
SETUP from the DVD mode. Refer to “Selecting the  
Language” on page 15 to changing the on-screen  
menus.  
¡In case of selecting from the DVD mode, you cannot  
select “CHANNEL SET UP” menu.  
Yoruba  
Zulu  
If you choose a Language that has a 3 letter language  
code, the code will be displayed every time you change  
the Audio or Subtitle language setting on page 24. If  
you choose any other languages, ‘---’ will be displayed  
instead. (3 letter language code is written in bracket.)  
EN  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
0C28  
DISPLAY SETTING  
AUDIO SETTINGS  
Choose the appropriate Audio settings for your equip-  
ment as it only affect during the playback of DVD  
discs.  
DVD-V  
You can change certain aspects of the DVD display  
screens and on-screen messages on the TV screen.  
1
Press SETUP twice in STOP mode so that  
the DVD SETUP menu appears.  
1
Press SETUP twice in STOP mode so that  
the DVD SETUP menu appears.  
¡If the menu does not appear, press PLAY, STOP,  
¡If the menu does not appear, press PLAY, STOP,  
then SETUP twice.  
then SETUP twice.  
QUICK SETUP  
TV MODE  
4:3 LETTER BOX  
DOLBY DIGITAL ON  
QUICK SETUP  
TV MODE  
4:3 LETTER BOX  
DOLBY DIGITAL ON  
2
Press B to select CUSTOM, then press  
ENTER.  
2
Press B to select CUSTOM, then press  
ENTER.  
¡CUSTOM mode will appear.  
¡CUSTOM mode will appear.  
3
Press Arrow (s /B) to select AUDIO, then  
press ENTER to confirm.  
3
Press Arrow (s /B) to select DISPLAY, then  
press ENTER to confirm.  
AUDIO  
DRC  
OFF  
ON  
DOLBY DIGITAL  
DISPLAY  
DOWN SAMPLING ON  
TV MODE  
4:3 LETTER BOX  
ON  
ANGLE ICON  
AUTO POWER OFF ON  
4
Press Arrow (K/L) to select the below  
items, then press ENTER.  
DRC (Dynamic Range Control):  
¡To compress the range of sound volume.  
¡The default setting is OFF.  
4
Press Arrow (K/L) to select the below  
items, then press ENTER.  
TV MODE:  
QUICK  
¡Press Arrow (K/L) for an item selection, then press  
ENTER.  
¡Select 4:3 LETTER BOX for a black bars appears  
on top and bottom of the screen.  
¡Select 4:3 PAN & SCAN for a full height picture  
with both sides trimmed.  
¡The default setting is 4:3 LETTER BOX.  
DOLBY DIGITAL:  
Set to On when the unit is connected to a Dolby Digital  
Decoder.  
(ON: Output by Dolby Digital)  
(OFF: Convert the Dolby Digital to PCM (2 channel  
stereo))  
QUICK  
¡The default setting is ON.  
ANGLE ICON:  
DOWN SAMPLING:  
¡Set to ON when outputting in 48 kHz.  
¡The default setting is ON.  
When playing disc with copyright Protection  
¡If you select OFF, copyright protection will be acti-  
vated and sound will be down sampled at 48kHz.  
¡Press ENTER repeatedly to turn Angle icon ON or  
OFF.  
¡The default setting is ON.  
AUTO POWER OFF:  
¡Press ENTER repeatedly to turn Auto Power off ON  
or OFF.  
5
Press SETUP to exit.  
¡The default setting is ON and it will turn the  
TV/DVD to off automatically after 15 minutes of no  
use.  
5
Press SETUP to exit.  
EN  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
0C28  
PARENTAL CONTROL  
CONTROL LEVELS  
DVD-V  
¡
ALL  
All parental lock is cancelled.  
Parental Control limits the disc viewing that exceed  
your settings. (with a password or playback will stop.)  
This feature allows you to prevent discs with alterna-  
tive scenes from being played by your children.  
¡
Level 8  
DVD software of any grade (adult/general/children)  
can be played back.  
¡
Levels 7 to 2  
PARENTAL LEVEL  
Only DVD software intended for general use and  
children can be played back.  
¡
Only DVD software intended for children can be  
played back, with those intended for adult and  
general use prohibited.  
Parental Level allows you to set the rating level of  
your DVD discs. Playback will stop if the disc’s rat-  
ings exceed the level you set.  
Level 1  
1
Press SETUP twice in STOP mode so that  
the QUICK SETUP menu appears.  
¡If the menu does not appear, press PLAY, STOP,  
then SETUP twice.  
IF YOU FORGET THE PASSWORD  
QUICK SETUP  
1
Press 4, 7, 3, 7 at step 4. Then enter your  
new password.  
TV MODE  
4:3 LETTER BOX  
DOLBY DIGITAL ON  
¡Password will be cleared and parental level will be  
set to ALL.  
2
3
Press B to select CUSTOM, then press  
ENTER.  
2
Proceed the above Steps 5-7 again.  
Press Arrow (s/B) to select PARENTAL,  
then press ENTER.  
PARENTAL  
PARENTAL LEVEL ALL  
4
5
6
7
Enter your four-digit password then press  
ENTER.  
Press Arrow (K/L) to select PARENTAL  
LEVEL, then press ENTER.  
Press Arrow (K/L) to select the desired  
level.  
Press SETUP to exit  
NOTES  
¡When doing this for the first time, enter any 4 digits.  
(except for 4737) That number will be used as the  
password from the second time onward.  
¡To change the password, press Arrow (K/L) to  
select CHANGE at step 5, then press ENTER. Enter  
the four-digit pass-word, then press ENTER.  
¡With some DVDs, it may be difficult to find if they  
are compatible with parental lock. Be sure to check  
if the parental lock function operates in the way that  
you have set.  
¡Record the password in case you forget it.  
EN  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
0C28  
TROUBLESHOOTING GUIDE  
If the TV/DVD does not perform properly when operated as instructed in this Owner’s Manual, check the  
player, consulting the following checklist.  
Problem  
Corrective Action  
Make sure the power plug is connected to an AC outlet.  
Make sure the power is turned on.  
Check if the power plug is connected to an AC outlet.  
Check the batteries in the remote control.  
Aim the remote control directly at the remote sensor. If necessary,  
remove all the obstacles between the sensor and the remote.  
You have to be within 23 feet of the TV/DVD.  
No power.  
The TV/DVD does not respond to  
the remote control.  
Check if the correct mode is selected. If not switch the mode by  
pressing SELECT on the remote control,whichever you need.  
TV Mode  
Problem  
Corrective Action  
No Picture or Sound  
Try a new channel, if OK, then possible station trouble.  
Make sure the power is turned on.  
Press SELECT on the remote control to select TV mode. Then try  
other TV feature.  
Is antenna connected to terminal on the back of the set?  
If outside antenna is being used, check for broken wire.  
If outside antenna is being used, check for broken wire.  
Check for local interference.  
Try a new channel, if OK, then possible station trouble.  
If outside antenna is being used, check for broken wire.  
Try a new channel, if OK, then possible station trouble.  
If outside antenna is being used, check for broken wire.  
Check for local interference.  
Try a new channel, if OK, then possible station trouble.  
Is antenna connected to terminal on the back of the set?  
If outside antenna is being used, check for broken wire.  
Adjust COLOR control.  
Try a new channel, if OK, then possible station trouble.  
Is antenna connected to terminal on the back of the set?  
If outside antenna is being used, check for broken wire.  
Check for local interference.  
Try a new channel, if OK, then possible station trouble.  
Is antenna connected to terminal on the back of the set?  
If outside antenna is being used, check for broken wire.  
Adjust CONTRAST & BRIGHT control.  
Try a new channel, if OK, then possible station trouble.  
Is antenna connected to terminal on the back of the set?  
If outside antenna is being used, check for broken wire.  
Check for local interference.  
Bars On Screen  
Picture Distorted or Blurred  
Picture Rolls Vertically  
Lines or Streaks in Picture  
No Color  
Poor Reception on Some Channels  
Ghosts in Picture  
Weak Picture  
Sound OK, Picture Poor  
Adjust CONTRAST & BRIGHT control.  
Try a new channel, if OK, then possible station trouble.  
Check for local interference.  
Magnetism from nearby appliances and geomagnetism might affect  
the color of the TV picture. Move the TV/DVD away from the appli-  
ances, the TV/DVD can repair itself automatically. If you want to  
repair immediately, unplug the TV/DVD power cord, then plug it in  
again 30 minutes or so later.  
Picture OK, Sound Poor  
Different color marks on screen.  
EN  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
0C28  
DVD Mode  
Problem  
Corrective Action  
• Connect the video cables firmly.  
No picture.  
• Insert a correct video disc that plays on this TV/DVD.  
• Press SELECT on the remote control to select DVD mode. Next,  
press PLAY or OPEN/CLOSE. Then, try other DVD feature.  
• Insert the disc.  
.
Disc cannot be played  
• Clean the disc.  
• Place the disc correctly, with the label side up.  
• Cancel the parental lock or change the control level.  
• Connect the audio cables firmly.  
.
No sound  
• Turn the power of the audio component on.  
• Correct the audio output settings.  
• Correct the input settings on the audio component.  
• This TV/DVD does not support DTS audio. This is not a malfunction.  
.
No DTS audio is output  
.
There are some cases where pictures may be slightly distorted, which are not a  
sign of a malfunction.  
Distorted picture  
• Although pictures may stop for a moment, this is not a malfunction.  
Audio or subtitle language  
does not match the set up  
The selected language is not available for audio or subtitles on the DVD.  
This is not a malfunction  
The camera angle cannot be changed • The DVD does not contain sequences recorded from different camera  
angles. This is not a malfunction  
Audio or subtitle language cannot be • The DVD does not contain audio source or subtitles in the selected  
changed  
language. This is not a malfunction.  
“Prohibited icon” appears on the  
screen, prohibiting an operation  
CD sound dropout  
• That operation is prohibited by the player or the disc.  
This is not a malfunction.  
• Scratched disc. Replace the disc with unscratched one.  
No CD reproduction  
DVD picture dropout  
DVD picture freeze  
DVD picture in mosaic  
No DVD reproduction  
NOTES:  
Some functions are not available in specific modes, but this is not a malfunction. Read the description in  
this Owner’s Manual for details on correct operations.  
Playback from a desired track and random playback are not available during program playback.  
EN  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
0C28  
MAINTENANCE  
CABINET CLEANING  
SERVICING  
Wipe the front panel and other exterior surfaces of  
the TV/DVD with a soft cloth immersed in luke-  
warm water and wrung dry.  
Never use a solvent or alcohol. Do not spray insec-  
ticide liquid near the TV/DVD. Such chemicals  
may cause damage and discoloration to the  
exposed surfaces.  
Should your TV/DVD become inoperative, do not  
try to correct the problem by yourself. There are no  
user-serviceable parts inside. Turn off, unplug the  
power cord, and please call our help line at 1-800-  
968-3429, to locate an Authorized Service Center.  
IF THE LASER OPTICAL PICKUP UNIT IS DIRTY  
If the player still does not perform properly when it is operated while referring to the relevant sections and to  
"TROUBLESHOOTING GUIDE" in this Owner's Manual, the laser optical pickup unit may be dirty. Consult  
your dealer or an Authorized Service Center for inspection and cleaning of the laser optical pickup unit.  
DISC HANDLING  
Use discs which have the following logos on them.  
(Optical audio digital discs.)  
To clean-off, use a soft cloth.  
Do not use a hard cloth since this will mar the disc.  
Wipe the disc in a straight line from center to edge.  
Never wipe with a circular motion.  
ReWritable  
Recordable  
Do not use detergent or abrasive cleaning agents.  
Handle the discs so that fingerprints and dust do  
not adhere to the surfaces of the discs.  
Always store the disc in its protective case when it  
is not used.  
EN  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
0C28  
SPECIFICATIONS  
GENERAL SPECIFICATIONS  
ELECTRICAL SPECIFICATIONS  
Sound output:  
2 speakers, 1W, 8 ohm  
TV  
CRT :  
9 inch in-line gun,  
90˚ deflection tube  
NTSC-M  
OTHER SPECIFICATIONS  
Terminals  
Television system:  
Antenna input:  
VHF/UHF/CATV  
TV Standard  
75 ohm unbalanced (F-type)  
RCA connector [ 1  
RCA connector [ 2  
Closed caption system: §15.119/FCC  
Channel coverage:  
Video input:  
Audio L/R input:  
Headphone:  
Coaxial digital  
audio output  
(only DVD):  
VHF:  
UHF:  
CATV:  
2 ~ 13  
14 ~ 69  
2 ~13, A ~ W,  
W+1 ~ W+84,  
A-5 ~ A-1, 5A  
181 channel  
1/8” stereo (3.5 mm)  
One pin jack,  
500m Vpp (75 ohm)  
Tuning System:  
Channel access:  
Analog audio L/R  
output:  
Remote control:  
frequency synthesized  
tuning system  
Direct access keyboard,  
programmable  
scan and up/down  
RCA connector [ 2  
Digital encoded  
infrared light system  
Operating  
temperature:  
5°C to 40°C  
(41°F~104°F)  
Power requirement : AC 120V/60Hz  
DC 13.2V  
Power consumption : AC 55W / DC 60W  
(Maximum)  
DVD  
Dimensions:  
H:12-1/4” (311mm)  
W:10-7/8” (276mm)  
D:12-1/2” (318mm)  
17.6 lbs (8.0 kg)  
Discs:  
DVD video, Audio CD  
Output signal format: NTSC color  
Frequency response  
Weight:  
(output jack)  
DVD (linear sound): 20 Hz to 22 kHz  
(sample rate: 48 kHz)  
20 Hz to 44 kHz  
(sample rate: 96 kHz)  
20 Hz to 20 kHz  
CD:  
Signal-to-noise ratio  
(S/N ratio)(output jack)  
CD:  
100 dB (EIAJ)  
Dynamic range  
(output jack)  
DVD (linear sound): 85 dB  
CD:  
84 dB (EIAJ)  
Total distortion factor  
CD:  
Wow and flutter:  
0.07% (EIAJ)  
Below the measurement  
limitation (+/-0.001%  
W PEAK) (EIAJ)  
Designs and specifications are subject to change without notice.  
If there is a discrepancy between languages, the default language will be English.  
EN  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
0C28  
Botón SEARCH (REV) h (panel delantero)  
Durante la reproducción o en el modo de pausa,  
mantenga presionado el botón durante unos  
segundos para cambiar la velocidad de  
reproducción hacia atrás.  
INDICE  
CONTROLES DE OPERACIÓN Y FUNCIONES . . . . . 33  
PANEL FRONTAL DEL TELEVISOR/DVD. . . . . . . . . . 33  
MANDO A DISTANCIA. . . . . . . . . . . . . . . . . . . . . . . . . 33  
VISTA POTERIOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33  
PARA INSERTAR LAS PILAS . . . . . . . . . . . . . . . . . . . . 34  
PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 34  
CONEXIONES DE ANTENA/CABLE . . . . . . . . . . . . . . 34  
LA ANTENA INTERIOR . . . . . . . . . . . . . . . . . . . . . . . . 35  
CONEXIÓN A TOMAS DE ENTRADA EXTERNA. . . . 35  
CONEXION MOVIL . . . . . . . . . . . . . . . . . . . . . . . . . . . 35  
CONEXIÓN A UN SISTEMA ESTÉREO . . . . . . . . . . . . 36  
CONEXIÓN A UN AMPLIFICADOR EQUIPADO CON  
TOMAS DE ENTRADA DIGITAL, PLATINA MD O  
10. Botón PLAY  
Inicia la reproducción del contenido del disco.  
Púlselo para cambiar a un modo de DVD cuando  
esta en el modo de televisor.  
11. Botón SKIP G  
Reproduce desde el inicio del siguiente capítulo  
o canción.  
Botón SEARCH (FWD) g (panel delantero)  
Durante la reproducción o en el modo de pausa,  
mantenga presionado el botón durante unos  
segundos para cambiar la velocidad de  
reproducción en avance.  
PLATINA DAT (Para DVD) . . . . . . . . . . . . . . . . . . . . . . 36  
CONEXCIONA UN DECODIFICADOR DOLBY  
DIGITAL (Para DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36  
12. Botón PAUSE  
TV SECTION  
Hace una pausa en la operación del disco.  
13. Botón OPEN/CLOSE  
PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 37  
SELECCIÓN DE IDIOMA . . . . . . . . . . . . . . . . . . . . . . . 37  
BORRADO (O AGREGACION) DE CANALES . . . . . . 37  
Púlselo para insertar discos en la bandeja o  
retirarlos de ella.  
DVD SECTION  
14. Toma HEADPHONE  
REPRODUCCIÓN DE UN DVD DE VÍDEO O UN  
CD DE AUDIO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38  
REPRODUCCION BASICA . . . . . . . . . . . . . . . . . . . . . . 38  
Para conectar auriculares (no suministrados) y  
escuchar en privado.  
15. Botón MODE  
Activa el modo de reproducción programada o el  
modo de reproducción aleatoria cuand se  
reproducen CDs o MP3.  
CONTROLES DE  
OPERACIÓN Y FUNCIONES  
16. Botones de números  
PANEL FRONTAL DEL  
TELEVISOR/DVD  
Modo del televisor:  
Pulse dos dígitos para tener acceso directamente  
al canal deseado.  
Consulte la figura 1 de la página 8  
Recuerde pulsar "0" antes de elegir un canal de  
un solo dígito.  
MANDO A DISTANCIA  
Botón +100  
Púlselo para seleccionar canales de televisión por  
cable cuyo número sea igual o superior al 100.  
Modo DVD:  
Consulte la figura 2 de la página 8  
VISTA POSTERIOR  
Púlselo para introducir el número deseado.  
Botón +10  
Consulte la figura 3 de la página 8  
Púlselo para introducir los números deseados  
cuyo número sea igual o superior al 10.  
17. Botón SLEEP  
1. Bandeja de carga del disco  
2. Toma de entrada VIDEO  
Conecte aquí la toma de salida de vídeo de una  
videocámara o de una videograbadora.  
3. Tomas de entrada AUDIO L/R  
Conecte aquí las tomas de salida de audio de una  
videocámara o de una videograbadora.  
4. Botón POWER  
Pulse el botón SLEEP para visualizar el  
temporizador para dormir y activar la función.  
La hora de apagado puede determinarse por el  
número de veces que usted pulsa el botón. (0,  
30,60,90 o 120 minutos)  
18. Botón REV h  
Púlselo para conectar y desconectar la alimentación.  
5. Botones VOLUME o/p(VOL.m/n)  
Púlselos para controlar el nivel del volumen para  
el DVD y el televisor.  
6. Botones CHANNEL o/p(CH.o/p)  
Púlselo para seleccionar el canal memorizado.  
Púlselo para cambiar a un modo de televisor  
cuando esta en el modo de DVD.  
Presione para ver la imagen en DVD en retroceso  
rápido. Presione PAUSE y presione este botón para  
empezar la reproducción en cámara lenta. Presione  
repetidamente este botón para cambiar la velocidad  
en avance de la cámara lenta.  
Botón FWD g  
Presione para avanzar rápidamente en el disco.  
Presione PAUSE y presione este botón para  
empezar la reproducción en cámara lenta.  
Presione repetidamente este botón para cambiar  
la velocidad de avance de la cámara lenta.  
19. Botón ZOOM  
7. Ventanilla del sensor del mando a distancia  
8. Botón STOP  
Detiene la operación del disco.  
9. Botón SKIP H  
Expand la Imagen para que llene toda la pantalla.  
Reproduce desde el inicio del capítulo o canción actual.  
ES  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
0C28  
20. Botón SETUP  
NOTA: Retire el cable de alimentación del gancho  
para evitar romperlo antes de conectarlo a  
una toma de CA convencional.  
Púlselo para activar o salir del modo de menús  
de televisor o preparación de DVD.  
21. Botón TITLE  
38. Toma de salida AUDIO L/R  
Conéctela a la entrada de audio analógico de un  
amplificador o decodificador externo.  
39. Toma de salida de audio digital COAXIAL  
(DVD Audio solamente)  
Visualiza el menú de títulos.  
22. Botón CLEAR  
Repone un ajuste.  
23. Botón DISPLAY  
Conéctela a la entrada digital de un amplificador  
o decodificador externo.  
Modo del televisor:  
Púlselo para visualizar el número del canal en la pantalla.  
Si lo pulsa de nuevo, el número del canal desaparecerá.  
Modo de DVD:  
40. Toma de entrada ANT.  
Conéctela a una antena, sistema de televisión por  
cable o sistema de satélite.  
Visualiza el estado actual en la pantalla del  
televisor con fines de comprobación.  
24. Botón SEARCH MODE  
Púlselo para localizar un punto deseado.  
25. Botón AUDIO  
41. Toma DC 13.2V  
Conecte en el cable de batería del coche.  
PARA INSERTAR LAS PILAS  
1) Abra la cubierta del compartimiento de las pilas  
empujando la cubierta del mando a distancia en el  
sentido de la flecha.  
2) Inserte 2 pilas "AA" en el compartimiento de las  
pilas, en el sentido indicado por las marcas de  
polaridad (+/-).  
Púlselo para seleccionar un idioma de audio o un  
modo de sonido deseado.  
26. Botón SUBTITLE  
Púlselo para seleccionar un idioma de subtítulos deseado.  
27. Botón REPEAT  
Repite la reproducción del disco, título, capítulo  
o pista actual.  
3) Vuelva a poner la cubierta.  
28. Botón ANGLE  
Púlselo para cambiar el ángulo de la cámara y  
ver, desde un ángulo diferente, la secuencia que  
está siendo reproducida.  
NOTAS:  
No mezcle pilas alcalinas y de manganeso.  
No mezcle pilas viejas y nuevas.  
29. Botón A-B REPEAT  
Repite la reproducción de una sección seleccionada.  
30. Botón RETURN  
PREPARACIÓN PARA LA  
UTILIZACIÓN  
Para volver a la operación anterior.  
31. Botón ENTER  
Púlselo para establecer un ajuste.  
32. Botones de flechas  
CONEXIONES DE  
ANTENA/CABLE  
Modo de televisor:  
Púlselo para seleccionar un modo de ajuste desde  
el menú que aparece en la pantalla del televisor.  
Púlselo para seleccionar o ajustar desde un menú  
particular.  
Consulte la figura 4 de la página 10  
Nota para el instalador de sistemas CATV  
Esta nota tiene la finalidad de llamar la atención del  
instalador de sistemas CATV para que tenga en  
cuenta el Artículo 820-40 del NEC, el cual  
proporciona consejos para hacer una conexión a  
tierra apropiada y, en particular, especifica que la  
tierra del cable deberá estar conectada al sistema de  
puesta a tierra del edificio, tan cerca del punto de  
entrada del cable como sea posible.  
Modo de DVD:  
Se utiliza cuando se hacen ajustes mientras se observa  
la visualización en una pantalla de televisor.  
33. Botón DISC MENU  
Visualiza menús en el DVD.  
34. Botón SELECT  
Púlselo para cambiar a un modo de televisor,  
modo de entrada externa o modo de DVD.  
NOTA:  
NOTA: Cuando seleccione el modo DVD con  
este botón, pulse primero PLAY u  
Antes de enchufar la antena a la toma ANT.IN del  
televisor/DVD, compruebe que la clavija no esté  
doblada. Si esta doblada, póngala derecha como se  
muestra en la ilustración, y luego conéctela en la  
toma ANT.IN del televisor/DVD.  
OPEN/CLOSE. De lo contrario, las funciones  
del DVD no se activarán.  
35. Botón MUTE  
Pulse el botón MUTE para apagar el sonido de  
un programa de TV. (La visualización del nivel  
del sonido cambia de ROJO CLARO a AZUL  
CLARO.) Pulse de nuevo el botón MUTE o el  
botón VOL m o n para restaurar el sonido.  
36. Botón PICTURE  
Clavija doblada  
Cable Clavija  
(Necesita enderezarse) (Clavija derecha)  
Presione para entrar en el modo de ajuste de imagen.  
37. Cable de alimentación  
ANTENA COMBINADA DE VHF/UHF  
La antena combinada de VHF/UHF de 75 ohmios  
puede conectarse al terminal ANT.  
Conéctelo a una toma de CA convencional  
(120 V/60 Hz).  
ES  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
0C28  
NOTA:  
Cuando conecte una videograbadora monofónica  
(otra fuente) a este televisor/DVD, conecte la toma  
de salida de audio de la videograbadora  
ANTENA SEPARADAS DE VHF/UHF  
En algunas zonas será necesario utilizar una antena  
exterior.  
TELEVICION POR CABLE SIN CAJA  
DE CONVERTIDOR / DECODIFICADOR  
Utilice esta conexión si su sistema de televisión por  
cable se conecta directamente a su televisor/DVD sin  
una caja de convertidor. Utilice el mando a distancia  
del televisor/DVD para seleccionar los canales.  
monofónica (otra fuente) a la toma AUDIO L de  
este televisor/DVD. El audio saldrá igualmente por  
los canales izquierdo y derecho.  
Consulte la figura 6 de la página 11  
TELEVICION POR CABLE CON CAJA  
DE CONVERTIDOR/DECODIFICADOR  
O CAJA DE SATRLITE  
CONEXION MOVIL  
ADVERTENCIA: El conductor nunca debe  
mirar el TV/DVD mientras conduce un  
vehículo.  
Si su compañía de televisión por cable le suministra  
una caja de convertidor, o si usted utiliza un sistema  
de satélite, usted podrá utilizar la conexión básica  
mostrada aquí.  
PRECAUCION:  
Cuando se utiliza en un vehículo en  
movimiento, cerciórese que la unidad está  
asegurada en todo momento para evitar que  
sufra heridas. Consulte con un instalador  
profesional.  
Si utiliza el TV/DVD con el motor del vehículo  
parado, vuelva a cargar la batería del  
vehículo después de unas 4 horas de uso  
para evitar que se agote. Después de  
terminar de utilizar el TV/DVD cerciórese de  
desenchufar el cable de batería de coche de  
la toma del encendedor de cigarrillos.  
No utilice este TV/DVD durante la  
conducción.  
La selección de los canales deberá hacerse con la caja  
de convertidor o con la caja de satélite. Esto significa  
que los canales no se podrán cambiar utilizando el  
mando a distancia del televisor/DVD.  
PARA VER UN CANAL  
CODIFICADO/DECODIFICADO  
1) Ponga el selector de canales del televisor/DVD  
en la posición del canal de salida de la caja de  
convertidor de televisión por cable o de la caja de  
satélite. (Ej., CH3)  
2) Seleccione el canal que va a ver en su caja de  
convertidor de televisión por cable o caja de  
satélite.  
No deje el TV/DVD en un coche.  
Este TV/DVD no fue diseñado para utilizar en  
un coche.  
1) La antena interior entregada es adecuada cuando  
el vehículo está estacionado. Para una mejor  
recepción en la calle o carretera, utilice una antena  
de TV móvil de VHF/UHF de alta calidad.  
2) Enchufe el cable de batería de coche en el conec-  
tor DC13,2 V (12V) en la parte trasera del  
TV/DVD.  
LA ANTENA INTERIOR  
La antena interior (suministrada) es desmontable.  
Inserte el vástago de la antena en el orificio de la  
parte posterior superior del televisor/DVD. Conecte  
la antena interior al televisor/DVD. Para obtener la  
mejor recepción, extienda completamente la antena  
interior y luego haga los ajustes necesarios. (Evite  
tocar la sección superior cuando haga los ajustes.)  
NOTA:  
• La conexión de una antena interior puede no dar  
siempre una recepción de TV aceptable.  
Para la toma del encendedor  
de cigarrillos del vehículo.  
Consulte la figura 5 de la página 10  
Antena móvil con  
combinación de  
VHF/UHF (no entregada)  
CONEXIÓN A TOMAS DE  
ENTRADA EXTERNA  
Cuando vea un programa grabado en otra fuente  
(videograbadora o videocámara), utilice las tomas de  
entrada de audio/vídeo de la parte delantera del  
televisor/DVD.  
Conecte las tomas de salida de audio/vídeo de otra  
fuente a las tomas AUDIO L/R y VIDEO de este  
televisor/DVD. Luego pulse SELECT hasta que  
aparezca "AUX" en la pantalla.  
Cable de batería  
de coche  
(entregado)  
ANT.  
DC 13.2V  
DC13.2V  
ANT.  
AUDIO OUT  
R
COAXIAL  
ES  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
0C28  
NOTAS:  
Ponga DOLBY DIGITAL en OFF para la salida de  
audio en el modo de preparación. La reproducción  
en un televisor/DVD utilizando ajustes incorrectos  
puede causar distorsión de ruido, y también se  
pueden dañar los altavoces. (Consulte la página 29  
para poner DOLBY DIGITAL en OFF.)  
Cerciórese que su vehículo tiene un sistema eléctri-  
co con tierra negativa de 13,2 voltios (12 voltios).  
Cerciórese de utilizar sólo el cable de batería de  
coche entregado. El uso de otros cables puede  
dañar el TV/DVD.  
Cerciórese que la toma está limpia de cenizas y  
otros restos.  
Cerciórese de enchufar firmemente el cable de  
batería de coche en la toma del encendedor de ciga-  
rrillos.  
Desenchufe siempre la batería del coche de la toma  
del encendedor de cigarrillos antes de desenchufar-  
lo del TV/DVD.  
Debe desconectar el cable de batería de coche del  
TV/DVD antes de poder utilizar la electricidad de  
CA.  
CONEXCIONA UN  
DECODIFICADOR DOLBY  
DIGITAL (Para DVD)  
Si utiliza este televisor/DVD para reproducir un disco  
DVD en un formato de sonido ambiental Dolby  
Digital de 5,1 canales, el televisor/DVD dará salida a  
un flujo de datos DOLBY DIGITAL desde su toma  
de salida de audio digital COAXIAL. Conectando el  
reproductor a un decodificador Dolby Digital, usted  
podrá disfrutar de un ambiente más convincente y  
real, con un sonido ambiental potente y de alta  
calidad similar al de los cines.  
Cerciórese de cambiar el fusible sólo por uno del  
mismo tipo, 6A, 250V.  
Utilice cables digitales coaxiales de audio disponibles  
en el comercio especializado para hacer las  
conexiones de audio.  
CONEXIÓN A UN SISTEMA  
ESTÉREO  
Consulte la figura 9 de la página 13  
NOTAS:  
Asegúrese de desconectar la alimentación de todos  
los componentes del sistema antes de conector a  
otro componente.  
Consulte los manuales del propietario de los  
componentes que vaya a conectar al televisor/DVD.  
Si conecta un decodificador Dolby Digital, ponga  
Consulte la figura 7 de la página 12  
NOTAS:  
Asegrese de desconectar la alimentación de todos  
los componentes del sistema antes de conectar otro  
componente.  
Consulte el manual del propietario de su sistema  
estéreo y de cualquier otro componente que vaya a  
conectar al televisor/DVD.  
Se escucha un sonido monoaural del sistema  
estéreo cuando el TV/DVD está en el modo de TV.  
DOLBY DIGITAL en ON para la salida de audio  
en el modo de preparación. (Consulte la página 29  
para poner DOLBY DIGITAL en ON.)  
A menos que se haga la conexión a un  
CONEXIÓN A UN  
decodificador Dolby Digital , ponga DOLBY  
DIGITAL en OFF para la salida de audio en el  
modo de preparación. La reproducción en el  
televisor/DVD utilizando ajustes incorrectos puede  
generar distorsión de ruido, y también puede  
estropear los altavoces.  
AMPLIFICADOR EQUIPADO  
CON TOMAS DE ENTRADA  
DIGITAL, PLATINA MD O  
PLATINA DAT (Para DVD)  
Utilice un cable digital coaxial de audio de venta en  
el comercio especializado para hacer las conexiones  
de audio.  
Fabricado bajo licencia de Dolby  
Laboratories. “Dolby” y el símbolo de la D  
doble son marcas de fábrica de Dolby  
Laboratories.  
Consulte la figura 8 de la página 12  
NOTAS:  
La fuente de audio de un disco en un formato de  
sonido ambiental Dolby Digital de 5,1 canales no  
se puede grabar como sonido digital mediante una  
platina MD o DAT.  
Asegúrese de desconectar la alimentación de todos  
los componentes antes de conectar otro  
componente.  
Consulte los manuales del propietario de los  
componentes que va a conectar al televisor/DVD.  
ES  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
0C28  
5 Tras la exploración  
TV SECTION  
El sintonizador se detiene en el canal memorizado  
más bajo. Si desea recuperar los canales  
seleccionados, podrá seleccionar los canales  
directamente con los botones de números o  
CHANNEL(CH.) K o L.  
PREPARACIÓN PARA LA  
UTILIZACIÓN  
Puede programar el sintonizador para explorar todos  
los canales que pueda recibir en su zona.  
NOTA: La programación de la memoria de canales  
no es necesaria cuando se hace la conexión a una caja  
de televisión por cable o a una caja de satélite. Ponga  
el selector de canales del televisor/DVD en la  
posición correspondiente al canal de salida de la caja  
de televisión por cable o caja de satélite (ej., CH3).  
Luego seleccione el canal que va a ver en la caja de  
televisión por cable o en la caja de satélite.  
BORRADO  
(O AGREGACION) DE CANALES  
TV  
Los canales que ya no reciban más o que se vean  
muy raramente podrán borrarse de la memoria. (Por  
supuesto, podrá volver a agregar en la memoria los  
canales que haya borrado de la misma.)  
SELECCIÓN DE IDIOMA  
1 Seleccione “AJUSTE DE CANAL”  
Pulse SETUP en el mando a distancia. Pulse K o L  
para apuntar a "AJUSTE DE CANAL".  
Luego, pulse ENTER.  
TV  
1 Preparacion de canales por primera vez  
Enchufe el cable de alimentación del televisor/DVD  
en una toma de CA.  
NOTA:  
2 Seleccion “AGREGAR/BORRAR”  
Pulse K o L para apuntar a "AGREGAR/BORRAR".  
Luego, pulse ENTER.  
Si aparecen algunos dígitos en la esquina de la  
pantalla, pulse POWER sin desenchufar el cable de la  
alimentación.  
3 Introduzca el número del canal deseado  
Pulse K o L hasta que aparezca el número del canal  
deseado. (Podrá utilizar también los botones de  
números o CH. K/L para introducirlos.)  
(Ejemplo: CH8)  
2 Encienda el televisor/DVD  
Pulse POWER para encender el televisor/DVD.  
3 Seleccione el idioma de la pantalla  
Pulse K o L para apuntar a "LANGUAGE".  
Luego, pulse ENTER para seleccionar "ENGLISH" o  
"ESP" = Spanish o "FRA" = French. "[ ]" indica el  
idioma seleccionado.  
4 Bórrelo de la memoria o agréguelo a ella  
Pulse ENTER. Los números de los canales se  
encienden en rojo. El canal se borra de la memoria.  
Canal agregado: Azul claro  
Canal borrado: Rojo claro  
4 Inicie el preajuste automático  
Pulse K o L para apuntar a  
"AUTOPRESELECCION". Luego, pulse ENTER. El  
sintonizador explora y memoriza todos los canales  
activos de su zona.  
¡Para borrar otro canal, repita los pasos [3] y [4].  
¡Si pulsa de nuevo ENTER, el canal se memorizará  
de nuevo.  
NOTAS:  
• El televisor/DVD distingue entre los canales de TV  
estándar y los canales de televisión por cable  
(CATV).  
5 Salga del modo de preparación de  
canales  
• El televisor/DVD puede memorizar canales de TV  
como canales de CATV si las condiciones de la  
recepción no son buenas. Si pasa esto, vuelve a  
intentar la acción AUTOPRESELECCION cuando  
las condiciones de la recepción sean mejores.  
Pulse SETUP en el mando a distancia para volver al  
modo del televisor.  
NOTA:  
Para confirmar que los canales hayan sido borrado o  
agregados, pulse CHANNEL(CH.) K o L.  
ES  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
0C28  
DVD SECTION  
REPRODUCCIÓN DE UN  
DVD DE VÍDEO O UN CD  
DE AUDIO  
REPRODUCCION BASICA  
DVD-V  
CD  
Para empezar  
¡Conecte el interruptor del amplificador y otros  
equipos, si fuera necesario.  
1 Pulse el boton POWER.  
¡La alimentación se conectará.  
2 Pulse el botón OPEN/CLOSE.  
¡La bandeja de carga del disco se abrirá.  
3 Ponga el dlsco en la bandeja con el lado  
de la eliguta hacia arriba.  
4 Pulse el botón PLAY.  
¡La bandeja se cerrará automáticamente y la  
reproducción empezará luego desde el primer  
capítulo o pista del disco. Si la reproducción no  
empieza automáticamente, pulse PLAY.  
¡Cuando reproduzca un DVD que tenga grabado un  
menú de títulos, el menú aparecerá en la pantalla.  
5
Pulse el botón STOP para detener la  
reproducción.  
ES  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
0C28  
MEMO  
ES  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
0C28  
LIMITED WARRANTY  
FUNAI CORP. will repair this SYLVANIA product, free of charge in the USA in the event of defect in materials or  
workmanship as follows:  
DURATION:  
PARTS:  
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the  
date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this  
warranty.  
LABOR: FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of  
original retail purchase.  
LIMITS AND EXCLUSIONS:  
THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE  
RECEIPT OR OTHER PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH  
THE PRODUCT TO OBTAIN SERVICE UNDER THIS WARRANTY.  
This warranty shall not be extended to any other person or transferee.  
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing  
or if service was attempted by an unauthorized service center. This SYLVANIA Limited warranty does not apply to  
any product not purchased and used in the United States.  
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It  
does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not  
supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication,  
alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this  
product or damage which results from fire, flood, lightning or other acts of God.  
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE  
CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.  
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY  
GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE  
USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL  
OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF  
FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY, AND  
FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS  
REPRESENTATIVES IN THE UNITED STATES.  
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY A FUNAI AUTHORIZED  
SERVICE CENTER. THIS WARRANTY IS VALID WHEN THE UNIT IS CARRIED-IN TO FUNAI  
AUTHORIZED SERVICE FACILITY.  
IMPORTANT:  
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS  
THAT VARY FROM STATE TO STATE, IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE  
UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI  
CORP.  
ATTENTION:  
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT  
WITHOUT PRIOR NOTICE.  
To locate your nearest SYLVANIA Authorized Service Center or for general service procedure,  
please call 1-800-968-3429 or write to the following:  
FUNAI CORPORATION, INC.  
Customer Service  
100 North Street; Teterboro, NJ 07608  
Tel :1-800-968-3429  
PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.  
Printed in Malaysia  
0EMN02108  
TD001UB #####  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Sennheiser Microphone SKM 100 User Manual
Sharp Freezer SJ PT55R User Manual
Sharp Projector XGC455W User Manual
Smooth Fitness Home Gym CE 74E User Manual
Sony Ericsson Network Card GC82 User Manual
Sony Microcassette Recorder ICD SX35 User Manual
SRS Labs Robotics SRS Robot Level 1 Kit User Manual
Sunbeam Fan 9100020009040 User Manual
Sunbeam Scale 78411 04 User Manual
System Sensor Smoke Alarm A05 1003 002 User Manual