OWNER S
MANUAL
ATSC/NTSC STB
6900DTD
®
As an ENERGY STAR
Partner, our company has determined
that this product meets the ENERGY
STAR® guidelines for energy efficiency.
ENERGY STAR® is a U.S. registered mark.
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.
If you need additional assistance for set-up or operating
after reading owner’s manual, please call
-
-
TOLL FREE : 1 800 968-3429
Please read before using this equipment.
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
THIS SYMBOL INDICATES THAT DAN-
GEROUS VOLTAGE CONSTITUTING A
RISK OF ELECTRIC SHOCK IS PRESENT
WITHIN THIS UNIT.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THIS SYMBOL INDICATES THAT THERE
ARE IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS IN THE
LITERATURE ACCOMPANYING THE
APPLIANCE.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSON-
NEL.
The caution marking is located on the rear of the cabinet.
IMPORTANT SAFEGUARDS
1.Read instructions-All the safety and operating instructions
should be read before the appliance is operated.
AMEUBLES- Cet appareil ne doit être
placé que sur un meuble (avec ou sans
roulettes) recommandé par le fabricant.
Si vous l’installez sur un meuble à
roulettes, déplacez les deux ensembles
avec précaution. Un arrêt brusque, l’util-
isation d’une force excessive et des surfaces irrégulières
risquent de déstabiliser l’ensemble et de le renverser.
2.Retain Instructions-The safety and operating instructions
should be retained for future reference.
3.Heed Warnings-All warnings on the appliance and in the
operating instructions should be adhered to.
4.Follow Instructions-All operating and use instructions
should be followed.
9. Ventilation-Slots and openings in the cabinet and the back
or bottom are provided for ventilation and to ensure reliable
operation of this product and to protect it from overheating,
and these openings must not be blocked or covered. The
openings should never be blocked by placing this product
on a bed, sofa, rug, or other similar surface. This product
should never be placed near or over a radiator or heat regis-
ter. This product should not be placed in a built-in installa-
tion such as a bookcase or rack unless proper ventilation is
provided or the manufacturer’s instructions have been
adhered to.
5.Cleaning-Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners. Use
a damp cloth for cleaning.
EXCEPTION: A product that is meant for uninterrupted
service and, that for some specific reason, such as the possi-
bility of the loss of an authorization code for a CATV con-
verter, is not intended to be unplugged by the user for clean-
ing or any other purpose, may exclude the reference to
unplugging the appliance in the cleaning description other-
wise required in item 5.
6.Attachments-Do not use attachments not recommended by
this product manufacturer as they may cause hazards.
10.Power Sources-This product should be operated only from
the type of power source indicated on the marking label. If
you are not sure of the type of power supply to your home,
consult your appliance dealer or local power company. For
this products intended to operate from battery power, or
other sources, refer to the operating instructions.
7.Water and Moisture-Do not use this product near water-for
example, near a bath tub, wash bowl, kitchen sink, or laun-
dry tub, in a wet basement, or near a swimming pool, and
the like.
11.Grounding or Polarization-This product is equipped with
a polarized alternating-current line plug(a plug having one
blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you
are unable to insert the plug fully into the outlet, try revers-
ing the plug. If the plug should still fail to fit, contact your
electrician to replace your obsolete outlet. Do not defeat
the safety purpose of the polarized plug.
8.Accessories-Do not place this product on an unstable cart,
stand, tripod, bracket, or table. This product may fall, caus-
ing serious injury to someone, and serious damage to the
appliance. Use only with a cart, stand, tripod, bracket, or
table recommended by the manufacturer, or sold with this
product. Any mounting of the appli-
ance should follow the manufactur-
er’s instructions and should use a
mounting accessory recommended
by the manufacturer. An appliance
and cart combination should be
moved with care.
Quick stops, excessive force, and
uneven surfaces may cause the
12.Power-Cord Protection-Power-supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying par-
ticular attention to cords at plugs, convenience receptacles,
and the point where they exit from the appliance.
appliance and cart combination to
overturn.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
FIGURE A
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
ANTENNA
LEAD I N
WI RE
GROUND
CL AMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRI C
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
NEC
-
NATIONAL ELECTRICAL CODE
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
S2898A
13.Outdoor Antenna grounding-If an outside antenna or
cable system is connected to this product, be sure the
antenna or cable system is grounded so as to provide some
protection against voltage surges and built-up static
charges. Article 810 of the National Electrical Code,
ANSI/NFPA No. 70, provides information with respect to
proper grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge unit,
size of grounding conductors, location of antenna-discharge
unit, connection to grounding electrodes, and requirements
for the grounding electrode. (Fig. A)
19.Damage Requiring Service-Unplug this product from the
wall outlet and refer servicing to qualified service person-
nel under the following conditions:
a. When the power-supply cord or plug is damaged or frayed.
b. If liquid has been spilled, or objects have fallen into this
product.
c. If this product has been exposed to rain or water.
d. If this product does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions, as improper adjust-
ment of other controls may result in damage and will often
require extensive work by a qualified technician to restore
this product to its normal operation.
14.Lightning-For added protection for this product receiver
during a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall
outlet and disconnect the antenna or cable system. This will
prevent damage to this product due to lightning and power-
line surges.
e. If this product has been dropped or damaged in any way.
f. When this product exhibits a distinct change in perfor-
mance-this indicates a need for service.
15.Power Lines-An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into
such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them
might be fatal.
20.Replacement Parts-When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer that have the same character-
istics as the original part. Unauthorized substitutions may
result in fire, electric shock, injury to persons or other haz-
ards.
21.Safety Check-Upon completion of any service or repairs to
this product, ask the service technician to perform routine
safety checks to determine that this product is in proper
operating condition.
16.Overloading-Do not overload wall outlets and extension
cords as this can result in a risk of fire or electric shock.
17.Object and Liquid Entry-Never push objects of any kind
into this product through openings as they may touch dan-
gerous voltage points or short out parts that could result in
a fire or electric shock. Never spill liquid of any kind on
this product.
22.Heat-This product should be situated away from heat
sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
18.Servicing-Do not attempt to service this product yourself
as opening or removing covers may expose you to danger-
ous voltage or other hazards. Refer all servicing to quali-
fied service personnel.
CAUTION:TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE
LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
PRECAUTIONS
IMPORTANT COPYRIGHT INFORMATION
LOCATION
For safe operation and satisfactory performance of
your this product, keep the following in mind when
selecting a place for its installation:
Shield it from direct sunlight and keep it away
from sources of intense heat.
Avoid dusty or humid places.
Avoid places with insufficient ventilation for proper
heat dissipation. Do not block the ventilation holes
at the top and bottom of the unit. Do not place the
unit on a carpet because this will block the ventila-
tion holes.
Unauthorized recording or use of broadcast televi-
sion programming, video tape, film or other copy-
righted material may violate applicable copyright
laws. We assume no responsibility for the unautho-
rized duplication, use, or other acts which infringe
upon the rights of copyright owners.
•
•
•
FCC WARNING- This equipment may gener-
ate or use radio frequency energy. Changes or
modifications to this equipment may cause
harmful interference unless the modifications
are expressly approved in the instruction man-
ual. The user could lose the authority to oper-
ate this equipment if an unauthorized change
or modification is made.
Install unit in a horizontal position.
Avoid locations subject to strong vibration.
Do not place this product near strong magnetic fields.
Avoid moving this product to locations where tem-
•
•
•
•
perature differences are extreme.
This equipment has been tested and found to com-
ply with the limits for a Class B digital device, pur-
suant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be deter-
mined by turning the equipment off and on, the
user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment
and receiver.
AVOID THE HAZARDS OF
ELECTRICAL SHOCK AND FIRE
•
•
Do not handle the power cord with wet hands.
Do not pull on the power cord when disconnecting
it from an AC wall outlet. Grasp it by the plug.
If, by accident, water is spilled on your unit, unplug
the power cord immediately and take the unit to our
Authorized Service Center for servicing.
Do not put your fingers or objects into this product
cassette holder.
Do not place anything directly on top of the unit.
•
•
•
3) Connect the equipment into an outlet on a cir-
cuit different from that to which the receiver is
connected.
4) Consult the dealer or an experienced radio/TV
technician for help.
The serial number of this product may be found on the back of the unit. No others has the same serial number
as yours. You should record the number and other vital information here and retain this book as a permanent
record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.
Date of Purchase
Dealer Purchase from
Dealer Address
Dealer Phone No.
Model No.
Serial No.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Before Using
Information on digital broadcasting
ATSC
NTSC
Receives both
ATSC and NTSC
Analog/digital
terrestrial signals
Analog/digital
terrestrial antenna
STB
TV
Digital broadcasting is the most advanced format of broadcasting, employing a new technology for
compression of audio and video signals which allows broadcasters to transmit digital signals using existing
terrestrial systems.
Due to this dramatic progress, new features of broadcasting service such as widescreen formats and higher
definition can provide a way to experience the full benefits of digital transmission.
High Definition Television (HDTV*) broadcasts can provide pictures twice as sharp as a conventional
broadcast and features sound encoded with Dolby® digital* 5.1 surround sound. When connected to a
receiver (sold separately) that features Dolby® digital decoding will provide a true theater experience in the
home.
Digital broadcasting has overcome problems experienced with analog television such as ghosting, "snowy"
pictures and interference. Digital television has a dramatic effect on these problems by its very nature.
In addition, the number of channels available has dramatically increased, so that you can make the best choice
among the variety of programs anytime with a clear picture.
The benefits extend not only to HDTV. It will also be possible to transmit multiple Standard Definition
Television (SDTV*) programs within the same bandwidth. Some data capacity could also be allocated to
provide more effective closed captioning or multiple language soundtracks.
Your current TV should be used for its entire service life.
STB will make this possible.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Before Using
Major features of STB
•
•
•
•
Capable of receiving digital (ATSC*), analog (NTSC*), and cable (NTSC) broadcasts
Capable of receiving High Definition TV broadcasts
Capable of receiving Dolby® digital 5.1 audio
Alternate languages for OSD are available.
(English, Spanish, French)
•
•
Component video output jacks (Y/ Pb/ Pr)
Sub-channels* are available through a single digital channel.
ATSC:
HDTV:
ATSC (Advanced Television Systems Committee) is
the group that has been working to establish the
standards for digital television broadcasting and
digital television equipment - including both SDTV
and HDTV.
High Definition Television:
HDTV signal formats are 1080i (interlaced scan) and
720p (progressive scan). HDTV provides the highest
resolution picture and audio in either stereo or 5.1
channel surround sound.
NTSC:
Dolby® Digital:
NTSC (National Television Standards Committee)
refers to the group that first established the standards
used for conventional analog television broadcasting
and TV equipment.
Dolby® Digital (when available) provides 6
independent soundtrack channels through the coaxial
output jack.
STB has a Dolby Digital output (labeled DIGITAL
AUDIO (COAXIAL)) that can be connected to an
external Digital Audio receiver/ decoder equipped
with a coaxial input. With additional equipment you
can enjoy more dynamic and realistic sound at home.
Sub-Channel:
Because of the compression of audio and video
signals, each digital channel is able to carry different
programs on sub-channels through a single channel.
You can select them by simply pressing CH o /
p
SDTV:
buttons on your remote control when available.
Standard Definition Television:
SDTV signal formats are 480p and 480i. SDTV
provides lower resolution, yet presents a very sharp,
clear picture. Lower resolution allows broadcasters to
transmit multiple programs per channel.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Before Using
Location of controls
FRONT PANEL
1 2
3
4
5 6 7
1 POWER button:
Turns STB on and off.
2 POWER indicator:
Lights up while STB is on.
NOTE:
When turning the STB on, the power indicator will blink first and light up.
When turning the STB off, the power indicator will blink first and go off.
3 Remote control sensor:
Receives signals from your remote control and enables you to control STB from a distance.
4 Navigation buttons o / p/ s / B:
Press to move the selected item or menu up, down, left or right.
5 SETUP button:
Press to enter or exit SETUP menu.
6 ENTER button:
In SETUP menu, press to determine your selection.
7 CHANNEL o / p buttons:
Press to change the channels up or down.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Before Using
REAR PANEL
1
2
3 4 5 6 8 7
1 ANT. IN Jack:
Use to connect an antenna to STB.
2 DIGITAL AUDIO (COAXIAL) Jack:
Use to connect a decoder or an amplifier to STB with a digital coaxial cable.
NOTE:
You must use this jack and a Dolby® Digital receiver for Dolby® Digital 5.1 playback.
3 AUDIO R/ L Jacks: (2 pairs)
Use to connect your TV, a stereo system or a VCR to STB with standard audio cables.
NOTE for audio output:
There will be both digital audio output and analog audio output during digital broadcast. There will be
only analog audio output during analog broadcast. When you want digital audio output during digital
broadcast, the digital audio (coaxial) jack must be used.
Refer to the page describing the connection to a decoder with Dolby® Digital.
4 VIDEO Jack: (Composite)
Use to connect your TV or a VCR to STB with a standard video cable.
5 S-VIDEO Jack:
Use to connect your TV to STB with an S-Video cable.
NOTE:
When you use an S-Video cable, a composite video cable (yellow) is not necessary.
6 COMPONENT VIDEO Jacks (Y/ Pb/ Pr):
Use to connect your TV to STB with component video cables.
NOTE:
This connection is required to display a high definition broadcast.
Y (green), Pb (blue), Pr (red)
7 Resolution selection switch (1080i/ 480p/ 480i):
Use to select the STB video output resolution 1080i, 480p and 480i. The default setting is 480i.
8 AC power cord:
Connect to AC outlet.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Before Using
REMOTE CONTROL
1 POWER button:
6
Turns STB on and off.
2 Number buttons:
7
8
1
2
Use to input channel numbers and passwords, and
to set time.
3 ENTER button:
In SETUP menu, press to determine your
selection.
9
10
4 CH o / p buttons:
Press to change the channels up or down.
3
4
5 Navigation buttons o / p / s / B:
Press to move the highlight up, down, left or
right.
11
5
The video pauses by pressing STILL o button
while you can listen to the program audio.
6 SETUP button:
Press to enter or quit SETUP menu.
7 AUDIO button:
Use to select an alternate audio track while
watching a TV program.
8 PREVIOUS button:
Use to go back to the previous screen in SETUP
menu or to exit.
9 INFO button:
Use to display further information on the channel
banner or to exit.
10 EPG button:
Use to display EPG (Electronic Program Guide)
or to exit.
11 CH RETURN button:
Use to return to the channel you were last
watching.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Before Using
Accessories
Installing batteries
You will find STB and the following accessories
when unpacking the carton box of STB:
1 Unsnap the battery cover from the back
of the remote control.
STB
6900DTD
Remote controller unit and AA batteries (x2)
(PART No.: NE120UD)
2 Install two AA batteries making sure
the polarity (+ / -) direction is correct.
Owners manual (PART No.: 0EMN02308)
NOTE:
When replacing batteries, make sure to replace them
in pairs.
3 Snap the battery cover back.
CAUTION:
•
Do not mix battery types.
(alkaline and manganese)
•
Do not recharge, short-circuit, heat, burn or
disassemble batteries.
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in
accordance with your local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regula-
tions concerning chemical wastes.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Before Using
Reference to SETUP menu
SETUP WIZARD
( Refer to page 25 through page 29. )
SETUP WIZARD
SETUP WIZARD guides you
through initial setup.
"SETUP"
"QUIT"
:
:
"Create new setup"
"Keep old setup"
QUIT
SETUP
Setting the clock (Manual)
(5/8)
Language for screen (1/8)
( Refer to page 25. )
SETUP WIZARD 1/8
SETUP WIZARD 5/8
( Refer to page 27. )
Enter current time.
YEAR 2001
--
--
--
--
---
--
DATE
TIME
SET
Channel scanning (2/8)
Setting the clock (Auto)
(6/8)
( Refer to page 26. )
SETUP WIZARD 2/8
SETUP WIZARD 6/8
( Refer to page 28. )
Now the system is scanning for channels.
Select a channel for auto clock setting.
Searching.
2
OFF
1
2
3
4
34%
Digital
Analog
SKIP
Daylight savings time
(DST) (3/8)
Screen ratio (7/8)
( Refer to page 29. )
SETUP WIZARD 3/8
SETUP WIZARD 7/8
( Refer to page 26.)
Select screen ratio.
16:9
Do you observe daylight saving time
(DST)?
4:3
ON
OFF
Time zone (4/8)
( Refer to page 26. )
Display mode (8/8)
( Refer to page 29. )
SETUP WIZARD 4/8
SETUP WIZARD 8/8
Select your time zone.
Select display mode.
LETTERBOX
CENTRAL
ZOOM
FULL
12
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Before Using
CHANNEL
DISPLAY
( Refer to page 43, 46, 49, 51.)
( Refer to page 54, 56.)
CHANNEL
DISPLAY
QUIT
QUIT
SCREEN RATIO
DISPLAY MODE
4:3
ADD/DELETE
ANTENNA
LETTERBOX
CHANNEL
DISPLAY
CLOCK
CHANNEL
AUTOSCAN
DISPLAY
CLOCK
DETAIL
DETAIL
Adding channels /
Deleting channels
( Refer to page 43, 46. )
Selecting screen formats
(Screen ratio)
( Refer to page 54. )
ADD/DELETE
DISPLAY
13-0
QUIT
CHANNEL
DISPLAY
CLOCK
QUIT
SCREEN
ADD
Select screen ratio.
13
22
23
55
DISPLAY
DELETE
CHANNEL
DISPLAY
CLOCK
16:9
4:3
DETAIL
DETAIL
Selecting screen formats
(Display mode)
( Refer to page 56. )
DISPLAY
Adjusting antenna
( Refer to page 49. )
ANTENNA
26-1
QUIT
CHANNEL
DISPLAY
CLOCK
QUIT
SCRE
Select display mode.
WEAK
STRONG
DISP
CHANNEL
DISPLAY
CLOCK
LETTERBOX
ZOOM
NOW
75
75
PEAK
PREVIOUS
FULL
DETAIL
DETAIL
Receiving channels (Autoscan)
( Refer to page 51. )
AUTOSCAN
QUIT
AutoScan will rescan all channels.
This may take
a
while to complete.
CHANNEL
DISPLAY
CLOCK
PREVIOUS
NEXT
DETAIL
13
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Before Using
CLOCK
( Refer to page 59, 60, 62, 64. )
CLOCK
2002/ 1/31( THU ) 2 50PM
QUIT
CHANNEL
DISPLAY
CLOCK
DST
ON
TIME ZONE
MANUAL
AUTO
CENTRAL
OFF
DETAIL
Setting the clock (Daylight Savings Time)
( Refer to page 60. )
CLOCK
QUIT
CHANNEL
Do you observe daylight saving time
(DST)?
DISPLAY
CLOCK
ON
OFF
DETAIL
Setting the clock (Time Zone)
( Refer to page 60. )
CLOCK
Select your time zone.
QUIT
CHANNEL
DISPLAY
CLOCK
CENTRAL
DETAIL
Setting the clock (Manual)
( Refer to page 62. )
CLOCK
Enter current time.
QUIT
CHANNEL
DISPLAY
CLOCK
YEAR 2002
DATE
TIME
1
2
31 THU
50 PM
SET
DETAIL
Adjusting the clock automatically
( Refer to page 64. )
CLOCK
Select a channel for auto clock setting.
QUIT
Searching.
2
OFF
CHANNEL
DISPLAY
CLOCK
1
2
3
4
DETAIL
14
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Before Using
DETAIL
( Refer to page 66, 69, 70, 71, 73, 77, 81, 84. )
DETAIL
QUIT
V-CHIP / CC
CHANNEL
DISPLAY
CLOCK
MENU LANGUAGE
ENGLISH
DETAIL
Setting for V-CHIP/CC
Setting for V-CHIP/CC
( Refer to page 69. )
( Refer to page 71. )
V-CHIP / CC
V-CHIP / CC
QUIT
QUIT
CHANNEL
DISPLAY
CLOCK
V-CHIP / CC
STB
OFF
Choose either STB or TV for
V-CHIP/CC setting.
CHANNEL
DISPLAY
CLOCK
MPAA RATING
TV RATING
If you choose "TV",
V-CHIP/CC functions are
processed in TV, not in STB.
CC SELECTION
NEW PASSWORD
TV
STB
DETAIL
DETAIL
V-CHIP/CC password
window
Setting MPAA rating
( Refer to page 73. )
V-CHIP / CC
( Refer to page 70. )
V-CHIP / CC
Set MPAA rating
QUIT
CHANNEL
DISPLAY
CLOCK
QUIT
CHANNEL
DISPLAY
CLOCK
X
Enter password.
NC-17
R
PG-13
PG
G
NR
DETAIL
DETAIL
Choosing the screen language
Setting TV rating
( Refer to page 77. )
V-CHIP / CC
( Refer to page 84. )
DETAIL
Set TV rating
QUIT
QUIT
CHANNEL
DISPLAY
CLOCK
V-CHIP / CC
Select menu language.
FV
V
S
L
D
TV-MA
CHANNEL
DISPLAY
CLOCK
MENU LANGU
TV-14
TV-PG
TV-G
TV-Y7
TV-Y
DETAIL
DETAIL
Setting CC options
( Refer to page 81. )
V-CHIP / CC
Select CC.
QUIT
CHANNEL
DISPLAY
CLOCK
OFF
V-CHIP / CC
CC1
CC2
MPAA RATING
TV RATING
CC3
CC4
TEXT1
TEXT2
TEXT3
TEXT4
CC SELECTION
NEW PASSWORD
DETAIL
Setting a new password
( Refer to page 66. )
V-CHIP / CC
QUIT
Enter password.
CHANNEL
DISPLAY
CLOCK
Confirm password.
DETAIL
15
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Connections
Connections to antenna
Use a standard antenna cable to connect the wall jack to the ANT IN Jack on STB.
STB connection to the antenna
NOTE:
Antenna and antenna cable are not included.
To the antenna
Rear panel of STB
WHEN CONNECTING TO CABLE BOX ALSO:
NOTE:
Antenna, antenna cable and Cable box are not included.
Incoming cable
signals
CABLE BOX
TV
ANT-IN
Jack
To the antenna
ANT
IN
ANT
OUT
Antenna cable
STB
Refer to following
pages for the
connection to TV.
ANT. IN
1 Use a standard antenna cable to connect the wall jack to the
ANT IN Jack on STB.
Note to the Cable TV System
Installer :
NOTE:
This reminder is provided to call
the Cable TV system installer’s
attention to Article 820-40 of the
National Electrical Code, which
provides guidelines for proper
grounding - in particular,
specifying that the cable ground
shall be connected to the grounding
system of the building, as close to
the point of cable entry as possible.
Refer to the following pages for the connection to TV.
2 Use an incoming cable to connect to an antenna input jack on
the cable box.
3 Use a standard antenna cable to connect an antenna output jack
on the cable box to an antenna input jack on the TV.
4 After completing the connection to TV, plug the AC power
cord of the TV into the AC outlet, then turn the TV on.
5 Select the output channel from the cable box e.g., ch3 or ch 4.
NOTE:
Refer to the TV owner’s manual for further information.
6 Plug the AC power cord of STB into the AC outlet, then turn
STB on.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Connections
CAUTION
When you connect the antenna cable to another device, be sure to use a splitter as shown below.
NOTE:
Antenna, antenna cable and Splitter are not included.
Right
Antenna cable
Splitter
e.g.: Connection to VCR
RF-IN
Antenna
cables
RF-OUT
STB
ANT. IN
Wrong
e.g.: Connection to VCR
RF-IN
Antenna
cables
RF-OUT
STB
ANT. IN
17
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Connections
Connections to other devices
There will be various ways of connecting STB to other devices. Make your connection according to your
choice of devices, screen format, and sound format.
You will find some sample connections in the following pages.
•
•
All jacks on STB will not need to be connected.
When you change the connections, all devices should be turned off.
•
Refer to each owner’s manual for further information on other devices.
STB connection using COMPONENT video output to TV
NOTE:
e.g.: Connection to HDTV
Component video cable and audio cable are not included.
Rear panel of STB
Component
video cable
Audio cable
To audio input jacks (L, R)
To component video input jacks (Y/ Pb/ Pr)
Resolution Selection Switch (1080i, 480p, 480i)
Refer to the TV owner s manual for the video resolution of your TV.
TV Format
1080i
Position of Resolution Selection Switch
If your TV is capable of displaying 1080i,
then select 1080i as shown.
If your TV is capable of displaying 480p,
then select 480p as shown.
480p
If your TV is capable of displaying 480i,
then select 480i as shown.
480i
18
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Connections
1 Use a standard antenna cable to connect the wall jack to the ANT IN jack on STB.
2 Use a standard audio cable to connect the audio output jacks (L, R) of STB to the audio input jacks (L, R) on
the TV.
NOTE:
If your TV is monaural (MONO) and has only one audio jack, use a standard audio cable (white) to
connect the audio output jack (white) on STB to the audio input jack (white) on the TV. The red cable and
jack will not be used.
3 Use a component video cable to connect the component video output jacks (Y/ Pb/ Pr) on STB to the
component video input jacks (Y/ Pb/ Pr) on the TV.
4 Set the video resolution selection switch to “1080i.”
NOTE:
For the capability of your TV and further information, refer to TV owner’s manual.
5 After completing the connection to the TV, plug the AC power cord of the TV into the AC outlet, then turn
the TV on.
6 Set the TV to the input mode.
NOTE:
Refer to the TV owner’s manual for further information.
7 Plug the AC power cord of STB into the AC outlet, then turn STB on.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Connections
STB connection using S-VIDEO output to SDTV
NOTE:
S-video cable and audio cable are not included.
Rear panel of STB
Audio cable
To audio input jacks (L, R)
S-video cable
To S-video input jack
1 Use a standard antenna cable to connect the wall jack to the ANT IN jack on STB.
2 Use a standard audio cable to connect the audio output jacks (L, R) of STB to the audio input jacks (L, R) on
the TV.
3 Use an S-video cable to connect the S-VIDEO output jack on STB to an S-video input jack on the TV.
4 Set the resolution selection switch to “480i.”
5 After completing the connection to the TV, plug the AC power cord of the TV into the AC outlet, then turn
the TV on.
6 Set the TV to the input mode.
NOTE:
Refer to the TV owner’s manual for further information.
7 Plug the AC power cord of STB into the AC outlet, then turn STB on.
NOTE:
When using an S-video cable to connect, the resolution of the video signal output will always be 480i.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Connections
STB connection using VIDEO output to SDTV
NOTE:
Audio cable and video cable are not included.
Rear panel of STB
Audio cable
Video cable
To audio input jacks (L, R)
To a video input jacks
1 Use a standard antenna cable to connect the wall jack to the ANT. IN jack on STB.
2 Use a standard audio cable to connect the audio output jacks (L, R) of STB to the audio input jacks (L, R) on
the TV.
NOTE:
If your TV is monaural (MONO) and has only one audio jack, connect a standard audio cable (white) from
the audio output jack (white) on STB to an audio input jack (white) on the TV. The red cable and jack will
not be used.
3 Use a standard video cable to connect the video output jack on STB to a video input jack on the TV.
4 Set the resolution selection switch to “480i.”
5 After completing the connection to the TV, plug the AC power cord of the TV into the AC outlet, then turn
the TV on.
6 Set the TV to the input mode.
NOTE:
Refer to the TV owner’s manual for further information.
7 Plug the AC power cord of STB into the AC outlet, then turn STB on.
NOTE:
When using a standard video cable to connect, the resolution of the video signal output will always be 480i.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Connections
STB connection to a standard stereo system
NOTE:
Component video cable and audio cable are not included.
Rear panel of STB
Component video cable
STEREO COMPONENT
To component video input
jacks (Y/ Pb/ Pr)
Audio cable
To audio input jacks
(L, R)
1 Use a standard antenna cable to connect the wall jack to the ANT. IN jack on STB.
2 Use a standard audio cable to connect the audio output jacks (L, R) on STB to the audio input jacks (L, R)
on the stereo.
3 Connect STB and the TV with a video cable.
NOTE:
Refer to the pages describing the connection to TV.
4 Set the video resolution selection switch to “1080i.”
NOTE:
For the capability of your TV and further information, refer to TV owner’s manual.
5 Plug the AC power cord of the stereo into the AC outlet, then turn the stereo on.
6 Set the stereo to the input mode to which you connected the audio from the STB.
NOTE:
Refer to the stereo owner's manual for further information.
7 Plug the AC power cord of STB into the AC outlet, then turn STB on.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Connections
STB connection to a decoder with Dolby Digital
NOTE:
Coaxial digital audio cable and component video cable are not included.
Rear panel of STB
To component video input
jacks (Y/ Pb/ Pr)
Digital Decoder
Coaxial digital
audio cable
To Coaxial digital
audio input jack
Component
video cable
1 Use a standard antenna cable to connect the wall jack to the ANT. IN jack on STB.
2 Connect a coaxial digital audio cable (purchase locally) from DIGITAL AUDIO (COAXIAL) output jack
on STB to a coaxial digital audio input jack on the digital decoder.
3 Connect STB and the TV with a video cable.
NOTE:
Refer to the pages describing the connection to TV for connecting to the TV.
4 Set the video resolution selection switch to “1080i.”
NOTE:
For the capability of your TV and further information, refer to TV owner’s manual.
5 Plug the AC power cord of the decoder into an AC outlet, then turn the decoder on.
6 Set the decoder to the input mode.
NOTE:
Refer to the decoder owner's manual for further information.
7 Plug the AC power cord of STB into an AC outlet, then turn them on.
NOTE:
STB will output the sound from the DIGITAL AUDIO (COAXIAL) output only when receiving a digital
broadcast.
Dolby® information:
Manufactured under license from Dolby Laboratories. "Dolby" and the double-D symbol are trademarks
of Dolby Laboratories.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Connections
STB connection to TV and Video devices (VCR, DVD recorder, etc)
NOTE:
e.g.: Connection to VCR
Audio cables and video cables are not included.
Rear panel of STB
To audio input
jacks (L, R)
Audio cable
Video cable
Audio
cable
VCR
To video input
jack
Video
cable
1 Use a standard antenna cable to connect the wall jack to the ANT IN jack on STB.
2 Use a standard audio cable to connect the set of audio output jacks (L, R) on STB to the set of audio input
jacks (L, R) on the VCR.
NOTE:
If your VCR is monaural (MONO) and has only one audio jack, use a standard audio cable (white) to
connect the audio output jack (white) on STB to the audio input jack (white) on the VCR. The red cable
and jack will not be used.
3 Use a standard video cable to connect the video output jack on STB to the video input jack on the VCR.
4 Set the video resolution selection switch to “480i.”
NOTE:
No matter where the switch is, the video resolution with this connection will be always 480i.
For screen ratio and display mode, the settings in Setup menu will be effective.
For the capability of your TV and further information, refer to TV owner’s manual.
5 Use a standard video cable to connect the video output jack on the VCR to the video input jack on the TV.
6 Use a standard audio cable to connect the set of audio output jacks (L, R) on the VCR to the audio input
jacks (L, R) on the TV.
7 Plug all AC power cords into AC outlets, then turn all devices on.
8 Set the TV and VCR to input mode.
NOTE:
Refer to the owner’s manuals of the TV and the VCR for further information.
NOTE:
When using a standard video cable to connect, the resolution of the video signal output will always be 480i.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Initial Setups (Setup Wizard)
Initial setup
1 SETUP WIZARD will appear.
SETUP WIZARD
SETUP WIZARD is the very convenient menu for
you to make the initial settings of STB.
Screen:
SETUP WIZARD
When STB is turned on for the first time after
connecting the AC power cord, SETUP WIZARD is
displayed on the screen automatically. You can
complete the following items for the initial Setups
through this menu.
SETUP WIZARD guides you
through initial setup.
"SETUP"
"QUIT"
:
:
"Create new setup"
"Keep old setup"
•
•
•
•
•
•
•
Language for screen
Channel Scanning
Daylight savings time (DST)
Time zone
Year/ date/ time
Clock
QUIT
SETUP
2 Select SETUP using s / B navigation
buttons, then press ENTER.
Screen ratio and display mode
•
SETUP WIZARD 1/8 will appear.
Remote:
8
1,2,3,6,7,
8,9,10,11,
12,13
SETUP WIZARD 1/8
1,2,3,6,7,
8,10,12,
13
25
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Initial Setups (Setup Wizard)
3 Select a desired language using o /
p
5 SETUP WIZARD 3/8 will appear.
navigation buttons, then press ENTER.
The selected language will be activated.
SETUP WIZARD 2/8 will appear.
•
•
SETUP WIZARD 3/8
Do you observe daylight saving time
(DST)?
ON
OFF
6 Select ON or OFF for Daylight Savings
Time (DST) using s / B navigation
buttons, then press ENTER.
•
SETUP WIZARD 4/8 will appear.
4 STB starts scanning channels.
•
•
Wait until the scanning is complete.
When the scanning is complete, “100%” will be
indicated in the box, then the next screen appears.
SETUP WIZARD 4/8
Select your time zone.
SETUP WIZARD 2/8
Now the system is scanning for channels.
CENTRAL
34%
Digital
Analog
SKIP
To skip the scanning:
Press ENTER.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Initial Setups (Setup Wizard)
7 Select the desired time zone using o /
s / B navigation buttons, then press
p
8 Enter YEAR, DATE and TIME using o /
s / B navigation buttons or number
buttons.
p
/
/
ENTER.
•
SETUP WIZARD 5/8 will appear.
•
Every time you enter a number, press ENTER to
move the cursor.
•
When going back and forth, press s /B
navigation buttons to move the cursor.
SETUP WIZARD 5/8
Enter current time.
YEAR 2001
--
--
--
--
---
--
DATE
TIME
SET
NOTE :
SETUP WIZARD 5/8
Enter current time.
YEAR 2001
Refer to “INFORMATION on Time Zones ” on page
61.
12 13 THU
10 30 PM
DATE
TIME
SET
NOTE:
After all information is entered, the cursor will move
to SET.
TIP:
To enter the YEAR, enter the last 2 digits of the year.
The year will be entered. (e.g., Enter “03” using
number buttons; 2003 will be shown.)
27
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Initial Setups (Setup Wizard)
9 Press ENTER when the cursor is on
SET.
10 Select the desired channel to search
from the channel map using o /
p
•
•
Your settings will be activated.
navigation buttons.
SETUP WIZARD 6/8 will appear, then STB will
start searching channels with Automatic Clock
Adjustments to keep the time correct.
SETUP WIZARD 6/8
Select a channel for auto clock setting.
Searching.
SETUP WIZARD 6/8
3
4
7
10 34
3
4
5
6
7
Select a channel for auto clock setting.
Searching.
48 52
2
OFF
2
3
4
5
NOTE:
The channel numbers with clock data will become
black in the channel map.
NOTE:
: Indicates that there are more channels above or
below.
: Indicates the top or bottom of the channel map.
When not using the auto-clock setting:
Select OFF on the channel map, then press ENTER.
CLOCK
Select a channel for auto clock setting.
Searching.
3
4
7
10 34
OFF
2
48 52
3
4
5
TIP:
OFF is located at the top of the channel map. Keep
pressing o navigation button to search.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Initial Setups (Setup Wizard)
NOTE:
Refer to “Selecting screen formats” on page 54 for
further information.
11 Press ENTER.
•
SETUP WIZARD 7/8 will appear.
13 Select the desired display mode using o /
p navigation buttons, then press ENTER.
SETUP WIZARD is completed.
•
STB will now start receiving broadcasts.
SETUP WIZARD 7/8
Select screen ratio.
16:9
World News 25
WWOR
26-1
ENGLISH STEREO
4:3
12 Select the desired screen ratio using o /
p navigation buttons, then press
ENTER.
NOTE:
•
SETUP WIZARD 8/8 will appear.
Refer to “Selecting screen formats” on page 54 for
further information.
SETUP WIZARD 8/8
Select display mode.
LETTERBOX
ZOOM
FULL
29
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Basic Operation
Watching TV
1 Turn the TV on and select the input to
which the STB is connected to.
STB is capable of receiving analog (NTSC format)
and digital (ATSC format) broadcasts.
All available channels from any of these broadcast
sources can be tuned in using the CH o/p buttons
and number buttons on your remote control.
Each channel number consists of a main channel
number and a sub-channel number.
2 Turn the STB on.
•
The power indicator on the STB front panel will
blink and light up.
Remote:
2
3
3 Selecting a desired channel.
When using CH o/p buttons:
3
3
3
•
•
Press CH o button to tune a higher channel
number.
Press CH p button to tune a lower channel
number.
TIP:
Be sure to complete AUTOSCAN in SETUP
WIZARD or in the SETUP menu so that STB
receives all channels available to be watched (ATSC
and NTSC).
30
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Basic Operation
2. Press ENTER.
When using number buttons (E.g., entering
26-1):
•
STB will tune in channel 26-1, and the program
being broadcast will be displayed.
1. Enter the main channel number, press the “–”
button, then enter the sub-channel number.
NOTE:
Sub-channel numbers from NTSC are always 0.
NOTE:
Every channel number consists of a main channel
and a sub-channel.
When selecting only with a main channel
number (E.g., entering 55 ):
Screen:
Puffy the Vampire Slayer
WWOR
26-1
TV-Y
2:00PM- 3:00PM
ENGLISH MONAURAL
Doublement Palace: Puffy takes a new job at a fast food restaurant
to make ends meet. Sarah Michelle Gellar, Nicholas BrendonAlyson
Hannigan, Elizabeth Anne Allen, Kari Rocha.
•
X appears momentarily as an alternate sub-
channel, then STB receives the sub-channel with
the smallest sub-channel number from either
NTSC or ATSC.
An alternate Sub-channel
26-1
55-X
Main channel Sub-channel
TIP:
When entering a 3-digit channel number, press the
“+100” button first, then enter the main channel
number.
SCANNING
Be sure to press the “–” button before entering the
sub-channel number.
The School
55-1
OTHER STEREO
31
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Basic Operation
When returning to the channel you were last
watching:
About sub-channel broadcasting:
There may be different programs being broadcast on
sub-channels through a single channel from ATSC.
You can watch each sub-channel program being
broadcast by selecting one of the sub-channels.
NTSC
ATSC
18:00
18:30
19:00
19:30
20:00
CH4-1
•
STB will tune back in the channel you were last
watching.
CH4-1 CH4-2 CH4-3
CH4-1
CH4-0
CH4-1
CH4-2
: changes automatically
: change manually by pressing CH / button
on your remote control.
NOTE:
NO SIGNAL will appear on the screen after the sub-
channel broadcast is over.
You will need to change the channel to continue
watching another TV program.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Basic Operation
1 Press INFO to display a channel
Channel banner
banner.
•
Channel information will appear in the channel
banner.
The channel banner provides you with information
on the channel you have selected.
Remote:
Screen:
1,2
Puffy the Vampire Slayer
WWOR
26-1
TV-Y
ENGLISH STEREO
2:00PM- 3:00PM
Doublement Palace: Puffy takes a new job at a fast food restaurant
to make ends meet. Sarah Michelle Gellar, Nicholas Brendon, Alyson
Hannigan, Elizabeth Anne Allen, Kari Rocha.
2 Press INFO to clear.
NOTE:
When tuning in a channel from NTSC:
The indicators “Program title” and “Program
description” are always as shown below.
EPG not provided.
7-0
NONE
MONAURAL
No description provided.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Basic Operation
Components of Channel Banner
Logo for broadcast source :
Indicates whether the channel is a
digital broadcast or an analog
broadcast.
Program title
Puffy the Vampire Slayer
WWOR
Channel number :
Indicates the current channel number.
26-1
Program rating
TV-Y
2:00PM- 3:00PM
ENGLISH MONAURAL
Doublement Palace: Puffy takes a new job at a fast food restaurant
to make ends meet. Sarah Michelle Gellar, Nicholas Brendon, Alyson
Hannigan, Elizabeth Anne Allen, Kari Rocha.
Program description
Audio type :
Indicates the current audio type.
Information icons
(See below for detail.)
Location bar :
Indicates the start and end times,
and the current status of progress.
Information icons
DTV:
NTSC:
HD (High Definition):
SD (Standard Definition):
SD (Standard Definition):
LOCK:
CC (Closed Caption):
V-CHIP/CC:
34
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Basic Operation
Choosing audio
and language
When the channel you are tuning in provides
alternate audio formats and languages, you can
change to any alternate.
1
When you are tuning in ATSC, language and format
can be set at the same time through an audio-map.
Audio map: (Only when tuning in ATSC)
Audio format and language outputs from a
broadcasting station are stored in an audio-map.
For example, when three language are available, the
sequence below will repeat and the desired audio
format and language can be set.
First Language (STEREO)
First Language (MONAURAL)
Second Language (STEREO)
Second Language (MONAURAL)
Third Language (STEREO)
Third Language (MONAURAL)
35
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Basic Operation
When tuning in ATSC:
The sequence will repeat according to audio-map
when the AUDIO button is pressed.
1 Press AUDIO button.
Remote:
No description provided.
CAT0001
77-1
ENGLISH 1/3 STEREO
When tuning in NTSC:
The sequence will repeat as shown below when
available.
Screen:
EPG not provided.
ENGLISH 1/3 STEREO
7-0
MONAURAL
ENGLISH 1/3 MONAURAL
SPANISH 2/3 STEREO
SPANISH 2/3 MONAURAL
OTHER 3/3 STEREO
MONAURAL
STEREO
OTHER 3/3 MONAURAL
SAP
NOTE:
(When available)
OTHER will be indicated when alternate languages
are not English, Spanish, or French.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Basic Operation
Picture Still
1 Press STILL o button while watching
TV.
You can stop the picture on the screen anytime by
pressing STILL o button.
•
STILL will be indicated on the lower left while
the picture is displayed.
Remote:
Screen:
1
STILL
NOTE:
During STILL, the programs audio will continue.
2 Press any button to quit.
•
The picture currently being broadcast will appear.
NOTE:
If the TV is left on STILL for a long period of time,
the still image may cause a burn-in effect damaging
the TV screen.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Basic Operation
RESTRICTED PROGRAM
On screen messages
Some messages are displayed on the screen during
channel changing or during programs.
When you have set V-CHIP and you receive a
program that meets any setting of yours, the whole
screen becomes gray, then RESTRICTED
PROGRAM appears in the center.
Please refer to “Setting for V-CHIP/CC” on page 69
for further information.
NO SIGNAL
When STB cannot receive a channel signal, the
whole screen becomes gray, then NO SIGNAL
appears in the center.
This may occur when:
•
•
•
the signal is too weak
the channel is not broadcasting
the antenna cable is not connected
RESTRICTED PROGRAM
Screen:
26-1
NOTE:
Press INFO button to verify the rating of a program
currently being received.
NO SIGNAL
Remote:
SCANNING
No description provided.
TV-14 D
Cowboy
When STB is trying to receive a signal, the whole
screen becomes gray, then SCANNING appears in
the center.
51-1
ENGLISH STEREO
No description provided.
RESTRICTED PROGRAM
26-1
SCANNING
The rating of this program
38
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
Electronic Program Guide (EPG)
1 Press EPG button while watching TV.
•
EPG will appear on the screen.
Electronic Program Guide (EPG) is an application for
digital channels that lists current and scheduled
programs that are or will be available on each
channel and a short summary or commentary for
each program.
Remote:
EPG is the electronic equivalent of a printed
television program guide.
You can view a list of programs scheduled for from
the next few hours up to the next seven days.
Screen:
NOTE:
CURRENT TIME:
EPG
(
)
1 / 31 THU 3 : 03PM
For displaying EPG, you will need to set TIME
ZONE, DST, and MANUAL of CLOCK in SETUP
WIZARD or in SETUP menu.
3:00PM
4:00PM
(
)
TODAY THU
22-
23-
26-
26-
55-
58-
0
0
1
2
1
0
NTSC
NTSC
EPG not provided.
EPG not provided.
State of the Union
Smallville
WWOR
WPIX
WB11 news at Ten
NTSC
22-0
EPG not provided.
EPG not provided.
No description provided.
4
NOTE:
Refer to Components of Electronic Program Guide
(EPG) for details on page 41.
3
1,4
2
39
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
2 Select the desired program using o / p / 3 Press ENTER.
s / B navigation buttons.
The cursor will move as you press any navigation
button.
When selecting a program being broadcast:
The selected program will appear.
•
•
State the Union
WWOR
26-1
CURRENT TIME:
ENGLISH STEREO
EPG
(
)
1 / 31 THU 3 : 03PM
3:00PM
4:00PM
(
)
TODAY THU
22-
23-
26-
26-
55-
58-
0
0
1
2
1
0
NTSC
NTSC
EPG not provided.
EPG not provided.
State of the Union
Smallville
WWOR
WPIX
WB11 news at Ten
NTSC
26-1
EPG not provided.
State of the Union
3:00PM-5:00PM
NONE
President Georgy W. Bush addresses Congress
and the nation; Minority Leader Richard
Gephardt gives the Democratic response.
When clearing EPG:
Press EPG or PREVIOUS.
The program previously watched will appear.
When viewing EPG for the next two hours up
to the next seven days:
Press B navigation button.
•
EPG for the next two hours will appear.
NOTE:
By pressing B navigation button, EPG will move
ahead.
When going back to the previous page:
Press s navigation button.
EPG not provided.
22-0
MONAURAL
•
The previous page of EPG will appear.
NOTE:
By pressing s navigation button, EPG will move
back.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
Components of Electronic Program Guide (EPG)
Current bar :
Indicates the current time
(so you can see how close you are to the start or end time of the program).
CURRENT TIME:
EPG
Current time
(
)
1 / 31 THU 3 : 01PM
3:00PM
4:00PM
Day of broadcasting
(
)
TODAY THU
22- 0
23- 0
NTSC
NTSC
EPG not provided.
EPG not provided.
State of the Union
Smallville
Program list
Channel numbers and digital
broadcasting station :
* "NTSC" programs are from
NTSC service.
26- 1
26- 2
26- 3
55- 1
WWOR
WPIX
Cursor :
Highlights the program currently
selected.
WB11 News at Ten
Matlock
WCBSDT
26-2
WB11 News at Ten
4:00PM-5:00PM
Tong, Watkins.
Program information :
Indicates the Information of the
program currently highlighted.
Program viewing :
G
Shows the program being
broadcast on the channel you are
choosing.
NOTE 1:
Descriptions for programs from NTSC are always
“EPG not provided.”
NOTE 2:
For channel numbers with blanked description, the broadcasting
station may not provide signals for EPG.
Information icons
LOCK:
Indicates that the current program is blocked according to your V-CHIP setting.
CC (Closed Caption):
Indicates that the program being broadcast is available with closed captioning.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
Setup menu for preference
includes:
•
•
•
ADD / DELETE:
You can add or delete channels in the channel map.
ANTENNA:
You can verify and adjust the signal strength of each channel to get a clearer picture.
AUTOSCAN:
You can get available channels automatically into the channel map by completing AUTOSCAN.
includes:
•
•
SCREEN RATIO:
You can fit the screen ratio to your TV screen.
DISPLAY MODE:
You can choose the display mode as you prefer.
includes:
•
•
•
•
Daylight Saving Time (DST):
You can set the Daylight Savings Time (DST).
TIME ZONE:
You can set the time zone.
MANUAL:
You can set the clock manually.
AUTO:
You can adjust the clock automatically using the channel clock data included in the signal from digital
broadcast sources.
includes:
•
•
V-CHIP/ CC:
You can make some settings for V-CHIP and closed caption including your own password.
MENU LANGUAGE:
You can choose the language you prefer for the screen menu.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
E.g., When adding the digital channel 26-1.
Adding channels
1 Press SETUP to display SETUP menu.
•
SETUP menu will appear.
ADD/ DELETE
You can add channels in the channel map.
Remote:
ADD:
You can add desired channels to the channel map.
Once you add channels to a channel map, you will be
allowed to select the channels in order using CH o /
p buttons.
NOTE:
Screen:
When you add digital and analog channels with the
same main channel number, you will need to add
each channel.
SETUP
QUIT
CHANNEL
DISPLAY
CLOCK
1,6
DETAIL
4
2,3,4,5
2,3,5
43
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
2 Select CHANNEL using o / p navigation 4 To add, first enter the digital channel
buttons, then press ENTER.
CHANNEL menu will appear.
number 26-1.
•
ADD/DELETE
QUIT
26-1
CHANNEL
ADD
QUIT
13
22
23
55
DELETE
CHANNEL
DISPLAY
CLOCK
ADD/DELETE
ANTENNA
CHANNEL
DISPLAY
CLOCK
AUTOSCAN
DETAIL
DETAIL
TIP:
You can enter simply 26 (main channel number) for a
digital channel.
3 Select ADD/ DELETE using o /
p
navigation buttons, then press ENTER.
ADD/ DELETE menu will appear.
NOTE:
•
For an analog channel, a sub-channel number must
be entered.
ADD/DELETE
13-0
QUIT
ADD
13
22
23
55
DELETE
CHANNEL
DISPLAY
CLOCK
DETAIL
44
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
INFORMATION on Channel Map
5 Select ADD using o / p navigation
buttons, then press ENTER.
ADD/DELETE
•
26-1 will be added to the channel map.
26-1
QUIT
CHANNEL
DISPLAY
CLOCK
ADD
13
22
23
26
DELETE
DETAIL
Channel map
ADD/DELETE
26-1
: Indicates an analog
channel.
QUIT
CHANNEL
DISPLAY
CLOCK
ADD
13
22
23
26
DELETE
: Indicates a digital
channel.
DETAIL
Added
NOTE:
Digital channels can be added only with main
channel numbers. When the digital channel added to
a channel-map has sub-channels, however, the sub-
channels can be selected using CH o / p buttons.
To continue adding:
Repeat Steps 4 and 5 to add channels.
6 Press SETUP to exit SETUP menu.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
E.g., To delete the digital channel 26-1.
Deleting channels
1 Press SETUP to display SETUP menu.
•
SETUP menu will appear.
ADD/ DELETE
You can add and delete channels in the channel map.
Remote:
DELETE :
You can delete channels from the channel-map.
NOTE:
When you delete digital and analog channels with the
same main channel number, you will need to delete
each channel.
Screen:
NOTE:
SETUP
Once you delete channels from a channel-map, you
cannot select those channels using CH o / p buttons.
QUIT
CHANNEL
DISPLAY
CLOCK
1,6
DETAIL
4
2 Select CHANNEL using o / p navigation
buttons, then press ENTER.
2,3,4,5
•
CHANNEL menu will appear.
2,3,4,5
6
CHANNEL
QUIT
ADD/DELETE
ANTENNA
CHANNEL
DISPLAY
CLOCK
AUTOSCAN
DETAIL
46
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
3 Select ADD/DELETE using o /
p
4 Select DELETE using o / p navigation
buttons, then press ENTER.
navigation buttons, then press ENTER.
•
ADD/ DELETE menu will appear.
•
The cursor will move to the channel map.
ADD/DELETE
ADD/DELETE
13-0
13-0
QUIT
QUIT
ADD
ADD
13
22
23
26
13
22
25
26
DELETE
DELETE
CHANNEL
DISPLAY
CLOCK
CHANNEL
DISPLAY
CLOCK
DETAIL
DETAIL
47
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
5 Select the digital channel number 26
using o / p navigation buttons.
6 Press ENTER when the cursor is on the
digital channel 26.
•
26-1 will be indicated in the box at the top of the
screen.
•
The digital channel number 26 will be deleted.
ADD/DELETE
55-1
Indicated
QUIT
ADD
ADD/DELETE
26-1
13
22
23
55
DELETE
CHANNEL
DISPLAY
CLOCK
QUIT
ADD
13
22
23
26
DELETE
CHANNEL
DISPLAY
CLOCK
DETAIL
To continue deleting:
DETAIL
Repeat Steps 5 and 6.
NOTE:
TIP:
: Indicates that there are more channels above or
below.
: Indicates the top or bottom of the channel map.
When adding a channel number previously deleted,
add the channel number by the steps in the ADD
menu or renew the whole channel map with the
AUTOSCAN menu.
7 Press SETUP to exit SETUP menu.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
E.g., when adjusting the digital channel 26-1.
Adjusting antenna
1 Select channel 26-1 to adjust using
number button or CH o / p buttons.
ANTENNA
•
Channel 26-1 will be tuned in.
You can verify the signal strength of each channel to
get a clearer picture for both digital and analog
broadcasts.
Remote:
2,6
or
1
3,4
1,5
3,4
Screen:
49
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
•
ANTENNA menu will appear, then STB starts
receiving the signal strength of the channel.
2 Press SETUP to display SETUP menu.
•
SETUP menu will appear.
ANTENNA
26-1
SETUP
QUIT
QUIT
CHANNEL
DISPLAY
CLOCK
WEAK
STRONG
CHANNEL
DISPLAY
CLOCK
NOW
56
75
PEAK
PREVIOUS
DETAIL
DETAIL
5 Adjust the antenna direction to get the
best reception.
3 Select CHANNEL using o / p navigation
buttons, then press ENTER.
•
A status bar stretches to the right according to the
signal strength.
•
CHANNEL menu will appear.
•
The value will be indicated on the left of the
status bar so that you can adjust the antenna
direction.
ANTENNA
26-1
QUIT
WEAK
STRONG
CHANNEL
DISPLAY
CLOCK
NOW
75
CHANNEL
75
PEAK
PREVIOUS
QUIT
DETAIL
ADD/DELETE
ANTENNA
CHANNEL
DISPLAY
CLOCK
Current value
Peak value
AUTOSCAN
When adjusting other channels
continuously:
DETAIL
Select the desired channel for adjusting using CH o /
p buttons, then adjust.
4 Select ANTENNA using o / p navigation
buttons, then press ENTER.
6 Press SETUP to exit SETUP menu.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
Receiving channels
1 Press SETUP to display SETUP menu.
•
SETUP menu will appear.
AUTOSCAN
Remote:
STB has the convenient function to get available
channels automatically.
AUTOSCAN is capable of receiving available
channels, both analog and digital, and storing those
channels in a channel map.
Channels once stored in a channel map can be
selected using CH o / p buttons.
Screen:
CAUTION:
SETUP
If AUTOSCAN is skipped, digital channels may not
be received even when channel numbers are correctly
entered.
QUIT
CHANNEL
DISPLAY
CLOCK
NOTE:
We recommend a complete AUTOSCAN to receive
all available channels properly.
DETAIL
2 Select CHANNEL using o / p navigation
buttons, then press ENTER.
1,4
•
CHANNEL menu will appear.
2,3,4
5
2,3,4
CHANNEL
QUIT
ADD/DELETE
ANTENNA
CHANNEL
DISPLAY
CLOCK
AUTOSCAN
DETAIL
51
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
3 Select AUTOSCAN using o /
p
4 Select NEXT using s / B navigation
buttons, then press ENTER.
navigation buttons, then press ENTER.
•
AUTOSCAN menu will appear.
•
Scanning window will appear, then STB will start
scanning for all available channels.
AUTOSCAN
AUTOSCAN
QUIT
Now the system is scanning for channels.
AutoScan will rescan all channels.
This may take a while to complete.
CHANNEL
DISPLAY
CLOCK
0%
Digital
Analog
PREVIOUS
NEXT
DETAIL
QUIT
NOTE:
It will depend on the location, however, it usually
takes approximately 3 minutes to complete.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
5 AUTOSCAN is complete.
To cancel AUTOSCAN during scanning:
Press SETUP or ENTER to cancel.
•
•
SETUP menu will go off automatically.
STB will receive broadcasts right after
AUTOSCAN is complete.
•
AUTOSCAN CANCELLED will appear on the
screen.
AUTOSCAN
Now the system is scanning for channels.
100%
Digital
Analog
QUIT
2-0
EPG not provided.
AUTOSCAN CANCELLED
7-0
MONAURAL
AUTOSCAN COMPLETED
CAUTION:
If AUTOSCAN is cancelled during scanning, some
channels not yet scanned may not be received.
It is recommended to complete AUTOSCAN.
NOTE:
Press CH o / p buttons to verify whether STB is
receiving channels being broadcast.
When NO SIGNAL appears on the screen:
Verify the antenna connection, then complete
AUTOSCAN again.
2-0
NO SIGNAL
53
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
Selecting screen formats
1 Press SETUP to display SETUP menu.
•
SETUP menu will appear.
STB allows you to select a screen ratio and a display
mode (aspect ratio) to match the formats of the
program being broadcast and your TV screen.
You can also change to aspect ratios you prefer to
watch.
Remote:
SCREEN RATIO
There are two screen ratios used in manufacturing
TVs. These are standard TV format (4:3), and
widescreen format (16:9).
Screen:
NOTE:
SETUP
Aspect ratio is the format for broadcasting and
displaying which are defined by the ratio of the
screen width to height.
QUIT
CHANNEL
DISPLAY
CLOCK
DETAIL
1,5
2 Select DISPLAY using o / p navigation
buttons, then press ENTER.
2,3,4
2,3,4
•
DISPLAY menu will appear.
DISPLAY
QUIT
SCREEN RATIO
4:3
DISPLAY MODE
LETTERBOX
CHANNEL
DISPLAY
CLOCK
DETAIL
54
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
3 Select SCREEN RATIO using o /
p
5 Press ENTER to exit SETUP menu.
navigation buttons, then press ENTER.
Screen ratio options will appear.
•
NOTE:
The screen ratio should be selected to fit your TV
screen.
Refer to the TV owner’s manual for further
information
DISPLAY
QUIT
SCREEN
Select screen ratio.
DISPLAY
CHANNEL
DISPLAY
CLOCK
16:9
4:3
DETAIL
4 Select the desired screen ratio using o /
p navigation buttons, then press
ENTER.
•
The screen ratio will be set.
DISPLAY
QUIT
SCREEN RATIO
4:3
DISPLAY MODE
LETTERBOX
CHANNEL
DISPLAY
CLOCK
DETAIL
55
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
DISPLAY MODE
1 Press SETUP to display SETUP menu.
•
SETUP menu will appear.
Remote:
1,5
2,3,4
2,3,4
Screen:
SETUP
QUIT
CHANNEL
DISPLAY
CLOCK
DETAIL
2 Select DISPLAY using o / p navigation
buttons, then press ENTER.
•
DISPLAY menu will appear.
DISPLAY
QUIT
SCREEN RATIO
4:3
DISPLAY MODE
LETTERBOX
CHANNEL
DISPLAY
CLOCK
DETAIL
56
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
NOTE:
You can choose the display mode as you prefer.
Refer to “INFORMATION on Screen Ratio and
Display Mode” on page 58 for further information.
3 Select DISPLAY MODE, using o /
p
navigation buttons , then press ENTER.
•
Display mode options will appear.
5 Press SETUP to exit SETUP menu.
CAUTION:
If the TV is left in LETTERBOX or SIDEBAR for a
long period of time, the still image may cause a burn-
in effect damaging the TV screen.
DISPLAY
QUIT
INFORMATION on 4:3 TV
When your 4:3 TV (capable of receiving a 1080i
signal) with the screen ratio 4:3 receives a 1080i
video output signal from STB, black/gray bars
may appear at the top and bottom of the screen.
That is because STB has been set to the screen
ratio to 4:3 and the display mode SIDEBAR.
SCRE
Select display mode.
DISP
CHANNEL
DISPLAY
CLOCK
LETTERBOX
ZOOM
FULL
DETAIL
appear because of TV settings.
4 Select the desired display mode using
o / p navigation buttons, then press
ENTER.
1080i video
output signal
4:3 TV
STB
•
The display mode will be set.
appear because of STB settings.
We recommend setting the STB screen ratio to
16:9, then setting the display mode as prefered,
or changing the resolution selection switch on
the rear panel of the STB to “480p” or “480i.”
DISPLAY
QUIT
SCREEN RATIO
4:3
DISPLAY MODE
LETTERBOX
CHANNEL
DISPLAY
CLOCK
DETAIL
57
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
INFORMATION on Screen Ratio and Display Mode
For standard 4:3 TVs displaying widescreen 16:9 broadcasts, your choices are:
4:3 TV screen
16:9 broadcast
Letter Box
Displays the entire picture image while fitting the picture to the screen by applying gray bars to
the top and bottom of the screen.
No information will be lost.
Zoom
Expands the picture image to fill the screen while cropping some images on the left and right.
Picture information on the left and right side will be lost.
Full
Displays the entire picture image while fitting the picture to the screen by stretching the image
vertically, so that it fills the screen.
No information will be lost, but there may be a slight distortion of the picture.
For widescreen 16:9 TVs displaying standard 4:3 broadcasts, your choices are:
16:9 TV screen
4:3 broadcast
Sidebar
Displays the entire picture centering the image by applying gray bars to the left and right sides of
the screen.
No information will be lost.
Zoom
Expands the picture image to fill the screen while cropping some images on the top and bottom.
Picture information on the top and bottom will be lost.
Full
Displays the entire picture image while fitting the picture to the screen by stretching the image
horizontally, so that it fills the screen.
No information will be lost, but there may be a slight distortion of the picture.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
Setting the clock
1 Press SETUP to display SETUP menu.
•
SETUP menu will appear.
To get the EPG (Electronic Program Guide) and
Channel banner, you need to set the CLOCK
correctly.
Remote:
NOTE:
The clock function is featured for displaying EPG so
there may be 5 minute-time lag a day at the
maximum. Therefore we recommend to set the Auto
clock setting to ON to use the clock function
effectively.
Screen:
In the CLOCK menu, set Daylight Savings Time
(DST) and TIME ZONE before setting the clock.
Those settings will be influential when setting the
current time.
SETUP
QUIT
CHANNEL
DISPLAY
CLOCK
NOTE:
Before going to MANUAL menu, set Daylight
Savings Time (DST) and TIME ZONE.
DETAIL
1,6
2 Select CLOCK using o / p navigation
buttons, then press ENTER.
4
•
CLOCK menu will appear.
2,3,4,5
2,3,4
CLOCK
2002/ 1/31( THU ) 2 50PM
QUIT
CHANNEL
DISPLAY
CLOCK
DST
ON
TIME ZONE
MANUAL
AUTO
CENTRAL
OFF
DETAIL
59
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
3 Select Daylight Savings Time (DST)
using o / p navigation buttons, then
press ENTER.
5 Select TIME ZONE using o /
p
navigation buttons, then press ENTER.
TIME ZONE setting menu will appear.
•
•
Daylight savings time setting menu will appear.
CLOCK
CLOCK
Select your time zone.
QUIT
QUIT
CHANNEL
CHANNEL
DISPLAY
CLOCK
DETAIL
CENTRAL
Do you observe daylight saving time
(DST)?
DISPLAY
CLOCK
ON
OFF
DETAIL
4 Select ON or OFF using s /
B
navigation buttons, then press ENTER.
Daylight savings time will be set, then CLOCK
menu will appear.
•
CLOCK
2002/ 1/31( THU ) 2 50PM
QUIT
DST
ON
TIME ZONE
MANUAL
AUTO
CENTRAL
CHANNEL
DISPLAY
CLOCK
OFF
DETAIL
60
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
INFORMATION on Time Zones
6 Select the desired time zone using o /
p/ s / B navigation buttons, then press
ENTER.
ALASKA:
ALASKA
•
The TIME ZONE will be set, then CLOCK menu
will appear.
HAWAII:
HAWAII
PACIFIC:
PACIFIC
CLOCK
2002/ 1/31( THU ) 2 50PM
MOUNTAIN:
QUIT
DST
ON
MOUNTAIN
TIME ZONE
MANUAL
AUTO
CENTRAL
CHANNEL
DISPLAY
CLOCK
OFF
CENTRAL:
CENTRAL
DETAIL
EASTERN:
EASTERN
ATLANTIC:
ATLANTIC
61
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
8 Enter YEAR, DATE, and TIME using o /
s / B navigation buttons or number
p
7 Select MANUAL using o / p navigation
buttons, then press ENTER.
/
•
The current time setting menu will appear.
buttons.
•
•
Press ENTER to set each value, then the cursor
will move to the next.
When going back and forth, press s /
B
navigation buttons to move the cursor.
CLOCK
Enter current time.
QUIT
YEAR 2002
CHANNEL
DATE
1
31 THU
50 PM
DISPLAY
CLOCK
DETAIL
TIME
2
SET
CLOCK
Enter current time.
QUIT
YEAR 2002
CHANNEL
DATE
3
31 SUN
52 PM
DISPLAY
CLOCK
DETAIL
TIME
1
SET
NOTE:
After all information is entered, the cursor will move
to SET.
TIP:
To enter the YEAR, enter the last 2 digits of the year.
The year will be entered. (e.g., Enter “03” using
number buttons; 2003 will be shown.)
62
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
9 Press ENTER when the cursor is on
SET.
•
Your settings will be activated.
Activated
CLOCK
2002/ 3/31( SUN ) 1 52PM
QUIT
CHANNEL
DISPLAY
CLOCK
DST
ON
TIME ZONE
MANUAL
AUTO
CENTRAL
OFF
DETAIL
10 Press SETUP to exit SETUP menu.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
1 Press SETUP to display SETUP menu.
Adjusting the clock
•
SETUP menu will appear.
automatically
STB is capable of adjusting the clock automatically
using the channel clock data included in the signal
from digital broadcast sources.
Remote:
In this menu, STB will search for channels with
clock data, then select a channel to adjust the clock.
STB will then adjust the clock using the channel
selected.
Screen:
SETUP
QUIT
CHANNEL
DISPLAY
CLOCK
1,10
2,3,4,5,6,
7,9,10
DETAIL
2,3,4,5,6,
7,9
2 Select CLOCK using o / p navigation
buttons, then press ENTER.
•
CLOCK menu will appear.
CLOCK
2002/ 1/31( THU ) 2 50PM
QUIT
CHANNEL
DISPLAY
CLOCK
DST
ON
TIME ZONE
MANUAL
AUTO
CENTRAL
OFF
DETAIL
64
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
3 Select AUTO using o / p navigation
buttons, then press ENTER.
5 Select the desired channel using o /
p
navigation buttons, then press ENTER.
The selected channel will be set, then the clock of
STB will be activated.
•
Auto clock setting menu will appear, then STB
will start searching for channels with clock data.
•
CLOCK
CLOCK
2002/ 1/31( THU ) 2 50PM
Select a channel for auto clock setting.
QUIT
QUIT
Searching.
DST
ON
2
TIME ZONE
MANUAL
AUTO
CENTRAL
OFF
1
CHANNEL
DISPLAY
CLOCK
CHANNEL
DISPLAY
CLOCK
2
3
4CH
4
DETAIL
DETAIL
TIP:
When not using the auto-clock setting:
You can select the desired channel being searched on
the channel map by moving the cursor even when
STB is in the searching mode.
Select OFF from the channel-map, then press ENTER.
TIP:
OFF is located at the top of the channel map. Keep
pressing o navigation button to search.
6 Press ENTER to exit SETUP menu.
4 When searching is complete, the
channel numbers being searched for
will become black on the channel map.
•
“Channel search completed.” will be indicated.
CLOCK
Select a channel for auto clock setting.
QUIT
4
OFF
2
CHANNEL
DISPLAY
CLOCK
3
4
5
Channel search
completed.
DETAIL
65
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
Setting a new password
1 Press SETUP to display SETUP menu.
•
SETUP menu will appear.
You will need to change the 4-digit password to
protect your V-CHIP/CC setting.
“0000” has been stored as the default password.
Remote:
NOTE:
Once the power supply is stopped due to the power
failure or the unplugging AC power cord for approx.
5 seconds, the password will go back to the default
password “0000.”
NOTE:
Screen:
Don’t forget your password.
It will be needed to set the V-CHIP/CC.
SETUP
QUIT
CHANNEL
DISPLAY
CLOCK
1,7
DETAIL
5
2,3,4,5
2 Select DETAIL using o / p navigation
button, then press ENTER.
•
DETAIL menu will appear.
2,3,4
DETAIL
QUIT
V-CHIP / CC
CHANNEL
DISPLAY
CLOCK
MENU LANGUAGE
ENGLISH
DETAIL
66
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
3 Select V-CHIP/CC using o / p navigation 4 Enter the default password “0000.”
•
“ * ” will appear for each digit.
button, then press ENTER.
V-CHIP/CC password window will appear.
•
V-CHIP / CC
QUIT
V-CHIP / CC
QUIT
Enter password.
CHANNEL
Enter password.
DISPLAY
CLOCK
DETAIL
CHANNEL
DISPLAY
CLOCK
DETAIL
After entering the default password, V-CHIP/CC
menu will appear.
V-CHIP / CC
QUIT
V-CHIP / CC
STB
OFF
CHANNEL
DISPLAY
CLOCK
MPAA RATING
TV RATING
CC SELECTION
NEW PASSWORD
DETAIL
67
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
6 Enter a new 4-digit password in the
upper space, then enter again in the
lower space to confirm.
5 Select NEW PASSWORD using o /
p
navigation buttons, then press ENTER.
•
Password setting menu will appear.
V-CHIP / CC
QUIT
V-CHIP / CC
QUIT
Enter password.
CHANNEL
Confirm password.
DISPLAY
CLOCK
DETAIL
Enter password.
CHANNEL
Confirm password.
DISPLAY
CLOCK
DETAIL
7 V-CHIP/CC menu will appear.
•
Your new password is stored.
V-CHIP / CC
QUIT
V-CHIP / CC
STB
OFF
CHANNEL
DISPLAY
CLOCK
MPAA RATING
TV RATING
CC SELECTION
NEW PASSWORD
DETAIL
8 Press SETUP to exit SETUP menu.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
Setting for V-CHIP/CC
V-CHIP/CC
In V-CHIP/CC menu, you will make some important
settings for the viewing programs you select.
First of all, you will need to set your 4-digit
password for your V-CHIP setting.
1,7
Then you can proceed with making your settings.
STB incorporates V-CHIP technology to block the
viewing of movies and television programs according
to their rating categories.
4
When V-CHIP and Closed Caption (CC) systems are
built into your TV, you can use STB V-CHIP/CC
settings.
2,3,4,5,6
In this menu, you will choose STB or TV as your
standard to transmit V-CHIP/CC information.
When V-CHIP/CC is set to STB, the settings will be
valid. Please set the rating level on the STB.
When set to TV, the settings are not valid. Please set
the rating level on the TV.
2,3,5,6
NOTE:
STB has been selected as the default before purchase.
V-CHIP is built into a TV or other video
devices to work in conjunction with the TV
Parental Guidelines. It electronically reads
television-programming ratings and allows
parents to block programs they believe are
unsuitable for their children.
There are two rating categories in use, TV
ratings for TV programs and MPAA ratings
for theatrical movies being broadcast.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
1 Press SETUP to display SETUP menu.
3 Select V-CHIP/CC using o / p navigation
buttons, then press ENTER.
•
SETUP menu will appear.
•
V-CHIP/CC password window will appear.
Remote:
Screen:
V-CHIP / CC
QUIT
SETUP
QUIT
CHANNEL
DISPLAY
CLOCK
Enter password.
CHANNEL
DISPLAY
CLOCK
DETAIL
DETAIL
2 Select DETAIL using o / p navigation
buttons, then press ENTER.
•
DETAIL menu will appear.
DETAIL
QUIT
V-CHIP / CC
CHANNEL
DISPLAY
CLOCK
MENU LANGUAGE
ENGLISH
DETAIL
70
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
4 Enter your 4-digit password.
5 Select V-CHIP/CC using o / p navigation
buttons, then press ENTER.
•
“ * ” will appear for each digit.
•
V-CHIP/CC setting menu will appear.
V-CHIP / CC
V-CHIP / CC
QUIT
QUIT
Choose either STB or TV for
V-CHIP/CC setting.
CHANNEL
If you choose "TV",
Enter password.
DISPLAY
CHANNEL
V-CHIP/CC functions are
processed in TV, not in STB.
CLOCK
DISPLAY
CLOCK
DETAIL
TV
STB
DETAIL
NOTE:
To set V-CHIP/CC settings, choose STB.
After the correct password is entered, V-CHIP/CC
menu will appear.
When choosing “STB” controls V-CHIP Ratings:
•
•
•
The STB settings of V-CHIP/CC will become
effective.
You will need to make the settings of V-CHIP/CC
with STB.
You can watch the program according to the STB
settings of V-CHIP/CC.
V-CHIP / CC
QUIT
V-CHIP / CC
STB
OFF
CHANNEL
DISPLAY
CLOCK
MPAA RATING
TV RATING
CC SELECTION
NEW PASSWORD
When choosing “TV” controls V-CHIP Ratings:
DETAIL
•
•
•
The STB settings of V-CHIP/CC will not become
effective.
You can watch the program according to the TV
settings of V-CHIP/CC.
You will need to make the settings of V-CHIP/CC
with the TV.
NOTE:
For the TV settings, refer to the TV owner’s
manual.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
6 Select STB or TV using s / B navigation
buttons, then press ENTER.
V-CHIP / CC
QUIT
V-CHIP / CC
STB
OFF
CHANNEL
DISPLAY
CLOCK
MPAA RATING
TV RATING
CC SELECTION
NEW PASSWORD
DETAIL
7 Press SETUP to exit SETUP menu.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
Setting MPAA rating
MPAA RATING
The MPAA (Motion Picture Association of America)
uses the standard movie ratings.
1,7
Age Label
Description
Not Rated by MPAA
NR
G
General Audience
4
Parental Guidance Suggested.
Some material may not be suitable for
children.
PG
2,3,4,5,6
Parents Strongly Cautioned.
Some material may be inappropriate for
children under 13.
PG-13
R
Restricted.
Under 17 requires accompanying parent
or guardian.
2,3,5,6
No one 17 and under admitted.
Some material is intended to be viewed
by adults only.
NC-17
X
No one 17 and under admitted.
Some material is explicitly sexual and is
intended to be viewed by adults only.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
1 Press SETUP to display SETUP menu.
3 Select V-CHIP/CC using o / p navigation
buttons, then press ENTER.
•
SETUP menu will appear.
•
V-CHIP/CC password window will appear.
Remote:
Screen:
V-CHIP / CC
QUIT
SETUP
QUIT
CHANNEL
DISPLAY
CLOCK
Enter password.
CHANNEL
DISPLAY
CLOCK
DETAIL
DETAIL
2 Select DETAIL using o / p navigation
buttons, then press ENTER.
•
DETAIL menu will appear.
DETAIL
QUIT
V-CHIP / CC
CHANNEL
DISPLAY
CLOCK
MENU LANGUAGE
ENGLISH
DETAIL
74
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
4 Enter your 4-digit password.
5 Select MPAA RATING using o /
p
navigation buttons, then press ENTER.
MPAA rating setting menu will appear.
•
“ * ” will appear for each digit.
•
V-CHIP / CC
Set MPAA rating
V-CHIP / CC
QUIT
QUIT
X
NC-17
CHANNEL
R
Enter password.
PG-13
PG
G
DISPLAY
CLOCK
DETAIL
CHANNEL
DISPLAY
CLOCK
DETAIL
NR
After entering the correct password, V-CHIP/CC
menu will appear.
V-CHIP / CC
QUIT
V-CHIP / CC
STB
OFF
CHANNEL
DISPLAY
CLOCK
MPAA RATING
TV RATING
CC SELECTION
NEW PASSWORD
DETAIL
75
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
6 Select PG-13 using o / p navigation
buttons, then press ENTER.
7 Press SETUP to exit SETUP menu.
E.g., when you want to block all PG-13
movies:
•
Lock indicators will be added to programs rated
PG-13 and above.
V-CHIP / CC
Set MPAA rating
QUIT
X
NC-17
CHANNEL
R
PG-13
PG
G
DISPLAY
CLOCK
DETAIL
NR
NOTE:
All movie programs rated PG-13 and above will be
blocked. When STB receives broadcasts of those
programs, STB will block both video and audio
signals to output, and RESTRICTED PROGRAM
will appear on the screen.
TIP:
Pressing ENTER will unblock a previously blocked
rating so that it can be selected.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
Setting TV rating
TV RATING
(TV Parental Guidelines)
TV rating allows parents to block out programs they
don’t want their children to see.
TV rating consists of the age labels and the content
labels.
1
The following are the descriptions for each label:
4
Age Label
TV-MA
Description
Mature Audience Only :
Specifically designed to be viewed by
adults and therefore may be unsuitable
for children under 17.
2,3,4,5
Possible content label : L, S, V
Parents Strongly Cautioned:
Contains some material that many
parents would find unsuitable for children
under 14 years of age.
2,3,5
TV-14
Possible content label : D, L, S, V
Parental Guidance Suggested :
Contains material that parents may find
suitable for younger children.
TV-PG
TV-G
Possible content label : D, L, S, V
General Audience :
Most parents would find this program
appropriate for all ages.
Directed to Older Children :
Designed for children age 7 and above.
Possible content label : FV
TV-Y7
TV-Y
All Children :
Designed to be appropriate for all children.
Content Label
Description
suggestive dialogue
D
L
coarse language
sexual situations
violence
S
V
FV
fantasy violence
NOTE:
When you block a particular rating or content label,
all categories above that will also be blocked.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
1 Press SETUP to display SETUP menu.
3 Select V-CHIP/CC using o / p navigation
buttons, then press ENTER.
•
SETUP menu will appear.
•
V-CHIP/CC password window will appear.
Remote:
Screen:
V-CHIP / CC
QUIT
SETUP
QUIT
CHANNEL
DISPLAY
CLOCK
Enter password.
CHANNEL
DISPLAY
CLOCK
DETAIL
DETAIL
2 Select DETAIL using o / p navigation
buttons, then press ENTER.
•
DETAIL menu will appear.
DETAIL
QUIT
V-CHIP / CC
CHANNEL
DISPLAY
CLOCK
MENU LANGUAGE
ENGLISH
DETAIL
78
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
4 Enter your 4-digit password.
5 Select TV RATING using o /
p
navigation buttons, then press ENTER.
TV rating setting menu will appear.
•
“ * ” will appear for each digit.
•
V-CHIP / CC
Set TV rating
V-CHIP / CC
QUIT
QUIT
FV
V
S
L
D
TV-MA
TV-14
TV-PG
TV-G
CHANNEL
DISPLAY
CLOCK
Enter password.
CHANNEL
DISPLAY
CLOCK
DETAIL
TV-Y7
TV-Y
DETAIL
After the correct password is entered, V-CHIP/CC
menu will appear.
INFORMATION on TV ratings
Content labels
V-CHIP / CC
QUIT
V-CHIP / CC
V-CHIP / CC
STB
OFF
CHANNEL
DISPLAY
CLOCK
MPAA RATING
TV RATING
Set TV rating
FV
QUIT
CHANNEL
DISPLAY
CLOCK
V
S
L
D
TV-MA
TV-14
TV-PG
TV-G
CC SELECTION
NEW PASSWORD
DETAIL
TV-Y7
TV-Y
DETAIL
Age-based category
Possible content labels
79
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
To set age-based ratings:
To set content-based ratings:
E.g., when you want to block all TV-14
programs
E.g., when you want to block only TV-14
programs that contain higher levels of
violence
1. Select TV-14 using o / p navigation buttons,
then press ENTER.
1. Select TV-14-V using o / p / s / B navigation
•
Lock indicators will be added to all TV-14 and
higher categories.
buttons, then press ENTER.
Lock indicators will be added to TV-14-V and
above.
•
V-CHIP / CC
V-CHIP / CC
Set TV rating
QUIT
Set TV rating
FV
V
S
L
D
QUIT
TV-MA
TV-14
TV-PG
TV-G
FV
V
S
L
D
CHANNEL
DISPLAY
CLOCK
TV-MA
TV-14
TV-PG
TV-G
CHANNEL
DISPLAY
CLOCK
TV-Y7
TV-Y
TV-Y7
TV-Y
DETAIL
DETAIL
NOTE:
All TV-14 and higher programs will be blocked,
along with all the labels of their possible contents.
When STB receives broadcasts of those programs,
STB will block both video and audio signals to
output, and RESTRICTED PROGRAM will appear
on the screen.
NOTE:
All TV-14-V and higher programs will be blocked.
When STB receives broadcasts of those programs,
STB will block both video and audio signals to
output, and RESTRICTED PROGRAM will appear
on the screen.
2. Press SETUP to exit SETUP menu.
2. Press SETUP to exit SETUP menu.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
Selecting CC options
1 Press SETUP to display SETUP menu.
•
SETUP menu will appear.
Remote:
CC SELECTION
Closed Caption (CC) provides you with on-screen
text versions of the audio content for the program
being broadcast.
In this menu, you are allowed to turn Closed Caption
signal On or Off, to set a language for the closed
caption and to choose a format for the closed caption.
Screen:
NOTE:
SETUP
OFF has been selected as the default before purchase.
QUIT
CHANNEL
DISPLAY
CLOCK
1,7
DETAIL
4
2,3,4,5,6
2 Select DETAIL using o / p navigation
buttons, then press ENTER.
•
DETAIL menu will appear.
2,3,5,6
DETAIL
QUIT
V-CHIP / CC
CHANNEL
DISPLAY
CLOCK
MENU LANGUAGE
ENGLISH
DETAIL
81
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
3 Select V-CHIP/CC using o / p navigation 4 Enter your 4-digit password.
•
“ * ” will appear for each digit.
buttons, then press ENTER.
V-CHIP/CC password window will appear.
•
V-CHIP / CC
QUIT
V-CHIP / CC
QUIT
Enter password.
CHANNEL
Enter password.
DISPLAY
CLOCK
DETAIL
CHANNEL
DISPLAY
CLOCK
DETAIL
After the correct password is entered, V-CHIP/CC
menu will appear.
V-CHIP / CC
QUIT
V-CHIP / CC
STB
OFF
CHANNEL
DISPLAY
CLOCK
MPAA RATING
TV RATING
CC SELECTION
NEW PASSWORD
DETAIL
82
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
5 Select CC SELECTION using o /
p
7 Press SETUP to exit SETUP menu.
navigation buttons, then press ENTER.
CC options menu will appear.
•
Use when Closed Caption is not desired.
V-CHIP / CC
are the primary caption and text services.
The captioning or text is displayed in the same
language as the program's dialog.
(up to 4 lines of script on the screen, where it does
not obstruct relevant parts of the picture)
Select CC.
QUIT
OFF
V-CHIP / CC
CC1
CHANNEL
DISPLAY
CLOCK
CC2
MPAA RATING
CC3
TV RATING
CC4
TEXT1
TEXT2
TEXT3
TEXT4
CC SELECTION
NEW PASSWORD
serve as the preferred data channels.
The captioning or text is often a secondary
language translation, simplified English, or
displayed at a slower rate.
DETAIL
6 Select the desired CC option using o /
p navigation buttons, then press
ENTER.
are rarely available and broadcasters use them
only in special conditions, such as when CC1 and
CC3 are not available, or TEXT1 and TEXT3 are
not available.
•
The selected CC option will be set.
V-CHIP / CC
QUIT
V-CHIP / CC
STB
CC1
CHANNEL
DISPLAY
CLOCK
MPAA RATING
TV RATING
CC SELECTION
NEW PASSWORD
DETAIL
83
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
Choosing the screen language
1 Press SETUP to display SETUP menu.
•
SETUP menu will appear.
MENU LANGUAGE
Remote:
English, French, and Spanish are available for the
screen menu. You can choose the language you
prefer.
NOTE:
ENGLISH has been selected as the default before
purchase.
Screen:
SETUP
1,5
QUIT
CHANNEL
DISPLAY
CLOCK
2,3,4
2,3,4
DETAIL
2 Select DETAIL using o / p navigation
buttons, then press ENTER.
•
DETAIL menu will appear.
DETAIL
QUIT
V-CHIP / CC
CHANNEL
DISPLAY
CLOCK
MENU LANGUAGE
ENGLISH
DETAIL
84
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Advanced Operation
3 Select MENU LANGUAGE using o /
p
4 Select the desired language using o /
p
navigation buttons, then press ENTER.
Language menu will appear.
navigation buttons (E.g., select French),
then press ENTER.
The selected language will be set, and the
selected language will be indicated on screen.
•
•
DETAIL
QUIT
V-CHIP / CC
Select menu language.
CHANNEL
DISPLAY
CLOCK
MENU LANGU
DETAIL
5 Press SETUP to exit SETUP menu.
85
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Appendix
Troubleshooting
Before requesting service for this unit, check the table below for a possible cause of the problem you are
experiencing. Some simple checks or a minor adjustment on your part may eliminate the problem and restore
proper operation.
Symptom
No power
Remedy
• Make sure that the AC power cord is securely plugged into the power outlet.
• Make sure that STB is turned on.
• Make sure to point the remote control unit at the remote control sensor.
• You may be too far from STB. Try moving closer.
• Remove any obstacles between the remote control and the remote control
sensor.
• Make sure that the batteries are installed in the correct direction (+ and –).
• The batteries may be depleted. Replace them with new ones.
• Before using the remote control unit to operate, press buttons on the front
panel of STB instead.
The STB is not
responding to the remote
control unit
• Make sure that the video cable is correctly connected.
• Make sure that video devices (TV or monitor) are turned on.
• Make sure that video devices (TV or monitor) are correctly set to STB video
output channel. Refer to the TV owner’s manual for further information.
• Check the video cable. Either an S-video cable or a standard video cable is
required. Do not connect them at the same time.
No picture
• Check the antenna and the antenna cable. There may be damage or
interfering sources.
Picture is not clear
(when receiving analog
signals)
• Check the antenna and the antenna cable. There may be damage or
interfering sources.
"Snowy" picture
(when receiving analog
signals)
• Check the antenna outside. The antenna may be swaying because of the
wind.
Striped picture or black
and white picture
(when receiving analog
signals)
• There may be interfering sources.
Blocked noise on picture
(when receiving digital
signals)
• There may be interfering sources.
No EPG or the provided
information is wrong
• Make sure that the clock had been correctly set.
In CLOCK in SETUP menu, you need to set correctly DST, TIME ZONE
and MANUAL.
86
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Appendix
Symptom
Remedy
• Make sure that the audio cable is correctly connected.
• Make sure that audio devices (stereo, TV, decoder) are turned on.
• Make sure that audio devices (stereo, decoder) are correctly set to STB audio
output channel.
• Check the audio cable. Either a standard audio cable or a coaxial digital
audio cable is required. Do not connect them at the same time.
• When TV has only one audio input jack, use a standard audio cable (white)
to connect the audio output jack (white) on STB to the audio input jack on
the TV. The standard audio cable (red) and the audio output jack (red) are
not required.
No sound
• When receiving analog signals, coaxial digital audio does not produce digital
audio. Only when receiving digital signals, does coaxial digital audio
produce digital audio.
• When pressing AUDIO, STEREO and MONAURAL will repeat in
sequence. However, this will not affect the channels through the digital
audio out jack.
Audio problems when
using coaxial digital
audio cable
• Make sure that AUTOSCAN in SETUP WIZARD or SETUP menu has been
completed. It will be required when you setup STB for the first time or when
STB is moved to a location where other channels are broadcast.
• The selected channel does not exist at that time. There are not always sub-
channels being broadcast.
• When AUTOSCAN is interrupted and not completed, some channels will
not be received. Make sure to complete AUTOSCAN in SETUP menu.
No reception of digital
signals
The entered channel
number changes
automatically
• Many digital channels have alternate channel numbers. STB changes the
numbers automatically to the ones signifying the broadcasting stations.
These are the numbers used for analog broadcasts.
• Some channels are not received with AUTOSCAN in SETUP menu.
However, when you are sure they exist, find alternate channel numbers for
them (described above), then add the channel numbers with ADD in SETUP
menu. You may get the information on the web site of the broadcasting
stations.
No reception of channels
with weak signal
(AUTOSCAN)
When you forget the
password for V-CHIP
• Unplug the AC power cord and wait for approx. 5 seconds, then enter the
default number "0000."
Closed captioning
display (TEXT mode)
does not go off even
after changing channels
through STB.
• Change the TV setting to the other mode except VIDEO mode.
• Change channels through the TV.
87
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Appendix
Specifications
Glossary and Acronyms
Product
STB for ATSC/NTSC
ATSC:
ATSC (Advanced Television Systems Committee) is
the group that has been working to establish the
standards for digital television broadcasting and
digital television equipment - including both SDTV
and HDTV.
Connecting Jacks
ANT IN
F connector (75 ohm)
Video Output (component)
3-pin jack (Y, Pb, Pr)
S-Video Output
Audio map:
Mini DIN 4-pin jack (75 ohm)
Video Output
1-pin jack, 1Vpp
Analog Audio Output
2-pin jack (L, R)
Audio format and language outputs from a
broadcasting station are stored in an audio-map.
For example, when three language are available, the
sequence below will repeat and the desired audio
format and language can be set.
450 mVrms (100k ohm)
Digital Audio Output
1-pin jack (Dolby Digital)
Audio output jack:
Audio output jack is located on the rear panel of STB
and send audio signal to other device connected by a
audio cable.
Power Source
120 VAC+/-10 %, 60 Hz+/-0.5 %
Autoscan:
Power Consumption
AUTOSCAN is capable of receiving available
channels, both analog and digital, and storing those
channels in a channel map.
25 W (Power on), Less than 1 W (Power off)
ENERGY STAR adopted.
Channels once stored in a channel map can be
selected using CH o / p buttons.
Operating Condition
41 F° (5 C°) - 104 F° (40 C°)
Component video output jack (Y/ Pb/ Pr):
Component video output jack is located on the rear
panel of STB and provide superior picture to other
connections. And you can select the video resolution
by using the resolution selection switch.
Dimensions (W x H x D)
14-3/16"(W) x 2-15/16"(H) x 13(D)
(360 mm x 75 mm x 330 mm)
Weight
6.36 lbs. (2.89 Kg)
Designs and Specifications are Subject to change
without notice.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Appendix
Digital audio (coaxial) output jack:
Digital audio (coaxial) output jack send digital audio
data to audio devices equipped with a digital audio
(coaxial) input jack.
SD:
Standard Definition
SDTV:
Standard Definition Television:
Dolby® Digital:
Dolby® Digital (when available) provides 6
SDTV signal formats are 480p and 480i. SDTV
provides lower resolution, yet presents a very sharp,
independent soundtrack channels through the coaxial clear picture. Lower resolution allows broadcasters to
output jack.
transmit multiple programs per channel.
STB has a Dolby Digital output (labeled DIGITAL
AUDIO (COAXIAL)) that can be connected to an
external Digital Audio receiver/ decoder equipped
with a coaxial input. With additional equipment you
can enjoy more dynamic and realistic sound at home.
Sub-Channel:
Because of the compression of audio and video
signals, each digital channel is able to carry different
programs on sub-channels through a single channel.
You can select them by simply pressing CH o /
p
DST:
buttons on your remote control when available.
Daylight Savings Time
S-Video output jack:
Electronic Program Guide (EPG):
EPG is the electronic equivalent of a printed
television program guide.
S-Video output jack is located on the rear panel of
STB and provides a high-quality picture to video
devices equipped with an S-Video input jacks.
You can view a list of programs scheduled for from
the next few hours up to the next seven days.
Video output jack:
HD:
High Definition
Video output jack is located on the rear panel of STB
and send video signal to other device connected by a
video cable.
HDTV:
High Definition Television:
HDTV signal formats are 1080i (interlaced scan) and
720p (progressive scan). HDTV provides the highest
resolution picture and audio in either stereo or 5.1
channel surround sound.
MPAA:
Motion Picture Association of America
A guild governing rating assignments to movies.
NTSC:
NTSC (National Television Standards Committee)
refers to the group that first established the standards
used for conventional analog television broadcasting
and TV equipment.
Password:
A stored 4-digit number that you must provide in
order to make settings for V-CHIP/CC.
89
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Guía para rápida consulta
Ubicación de los controles
PANEL FRONTAL
PANEL TRASERO
1
2
3
4
5
6
8 7
1
2
3
4
5
6
7
1 Botón POWER:
1 Toma ANT. IN:
Para encender y apagar el STB.
Use esta toma para conectar una antena al STB.
2 Indicador POWER:
2 Toma DIGITAL AUDIO (COAXIAL):
Use esta toma para conectar un decodificador o
amplificador al STB mediante un cable coaxial
digital.
Se ilumina cuando el STB está encendido.
NOTA:
Cuando se enciende el STB, el indicador POWER
primero parpadea y luego se ilumina de manera
constante.
NOTA:
Para poder reproducir en el modo Dolby® Digital
5.1, deberá usar esta toma y un receptor Dolby®
Digital.
Cuando se apaga el STB, el indicador POWER
primero parpadea y luego se apaga.
3 Sensor de mando a distancia:
3 Tomas AUDIO R/ L: (2 pares)
Recibe las señales desde el mando a distancia, lo
que permite controlar el STB a distancia.
Use estas tomas para conectar el televisor, un
sistema estereofónico o una videograbadora al
STB mediante cables de audio estándar.
4 Botones de navegación o / p/ s / B:
Presione estos botones para mover el ítem o
menú seleccionado hacia arriba, hacia abajo,
hacia la izquierda o hacia la derecha.
4 Toma VIDEO: (compuesto)
Use esta toma para conectar el televisor o una
videograbadora al STB mediante un cable de
vídeo estándar.
5 Botón SETUP:
Presione este botón para entrar en el menú
SETUP o para salir de él.
5 Toma S-VIDEO:
Use esta toma para conectar el televisor al STB
mediante un cable S-vídeo.
6 Botón ENTER:
En el menú SETUP, presione este botón para
registrar la opción seleccionada.
NOTA:
Cuando se utiliza un cable S-vídeo, no es
necesario usar un cable de vídeo compuesto
(amarillo).
7 Botones CHANNEL o / p:
Presione este botón para cambiar de canal en
dirección de ascenso o descenso.
6 Tomas COMPONENT VIDEO (Y/ Pb/ Pr):
Use estas tomas para conectar el televisor al STB
mediante cables de vídeo de componente.
NOTA:
Esta conexión es necesaria para visualizar
emisiones de alta definición.
Y (verde), Pb (azul), Pr (rojo)
7 Interruptor selector de resolución
(1080i/ 480p/ 480i):
Use este interruptor para seleccionar la resolución
de salida de vídeo del STB: 1080i, 480p o 480i.
8 Cable de alimentación de CA:
Conéctelo a una toma de CA.
90
Download from Www.Somanuals.com. All Manuals Search And Download.
ES
Guía para rápida consulta
4 Botones CH o / p:
CONTROL REMOTO
Presione este botón para cambiar de canal en
dirección de ascenso o descenso.
6
5 Botones de navegación o / p / s / B:
Presione estos botones para mover el cursor hacia
arriba, hacia abajo, hacia la izquierda o hacia la
derecha.
7
8
1
2
Para hacer una pausa en el vídeo y seguir
escuchando el programa de audio, presione el
botón STILL o.
9
10
3
4
6 Botón SETUP:
Presione este botón para entrar en el menú
SETUP o para salir de él.
11
5
7 Botón AUDIO:
Use este botón para seleccionar una pista de
audio alternativa mientras ve un programa de TV.
8 Botón PREVIOUS:
Use este botón para retroceder a la pantalla
anterior del menú SETUP o para salir de este
menú.
9 Botón INFO:
Use este botón para visualizar información
adicional en el recuadro de canal o para salir.
1 Botón POWER:
Para encender y apagar el STB.
10 Botón EPG:
Use este botón para visualizar la EPG (Guía de
programas electrónicos) o para salir.
2 Botones numéricos:
Use estos botones para introducir números de
canal y contraseñas, así como para ajustar la hora.
11 Botón CH RETURN:
Use este botón para volver al último canal que
estaba viendo.
3 Botón ENTER:
En el menú SETUP, presione este botón para
registrar la opción seleccionada.
Instalación de las pilas
NOTA:
1 Quite la tapa del compartimiento de las
pilas, situada en la parte posterior del
mando a distancia.
Al cambiar las pilas, asegúrese de reemplazar las dos
pilas al mismo tiempo.
3 Coloque la tapa del compartimiento de
las pilas.
PRECAUCIÓN:
•
No utilice simultáneamente pilas de distinto tipo.
(alcalinas y de manganeso)
No recargue, cortocircuite, caliente, queme ni
desarme las pilas.
2 Instale dos pilas AA, asegurándose de
que la polaridad (+ / -) de las mismas
sea correcta.
•
91
Download from Www.Somanuals.com. All Manuals Search And Download.
ES
Guía para rápida consulta
Conexiones de antena
Use un cable de antena estándar para conectar la toma mural a la toma ANT IN del STB.
Conexión del STB a la antena
NOTA:
La antena y el cable de antena no vienen
incluidos con el producto.
A la antena
Panel trasero del STB
AL CONECTAR EL EQUIPO A UNA CAJA PARA CABLE:
NOTA:
Señales de televisión
por cable entrantes
La antena, el cable de antena y la caja para
cable no vienen incluidos con el equipo.
CAJA PARA CABLE
A la antena
Toma TV
ANT-IN
ANT
IN
ANT
OUT
Cable de antena
STB
Para la conexión
al televisor,
ANT. IN
consulte las
páginas siguientes.
1 Use un cable de antena estándar para conectar la toma mural a la toma ANT IN del STB.
NOTA:
Para la conexión al televisor, consulte las páginas siguientes.
2 Use un cable entrante para realizar la conexión a la toma de entrada de antena de la caja para cable.
3 Use un cable de antena estándar para conectar la toma de salida de antena de la caja para cable a la toma
de entrada de antena del televisor.
4 Después de completar la conexión al televisor, conecte el cable de alimentación de CA del televisor a la
toma de CA y encienda el televisor.
5 Seleccione el canal de salida en la caja para cable, es decir, el canal 3 o 4.
NOTA:
Para más información, consulte el manual de instrucciones de su televisor.
6 Conecte el cable de alimentación de CA del STB a la toma de CA y luego encienda el STB.
92
Download from Www.Somanuals.com. All Manuals Search And Download.
ES
Guía para rápida consulta
Conexión del STB a un SDTV utilizando la salida VIDEO
NOTA:
El cable de audio y el cable vídeo no vienen
incluidos con el producto.
Panel trasero del STB
Cable de audio
A las tomas de entrada
Cable de vídeo
de audio (L, R)
A la toma de entrada de vídeo
1 Use un cable de antena estándar para conectar la toma mural a la toma ANT IN del STB.
2 Use un cable de audio estándar para conectar las tomas de salida de audio (L, R) del STB a las tomas de
entrada de audio (L, R) del televisor.
NOTA:
Si su televisor es monofónico (MONO) y sólo tiene una toma de audio, conecte un cable de audio estándar
(blanco) entre la toma de salida de audio (blanca) del STB y la toma de entrada de audio (blanca) del
televisor. En este caso, el cable y la toma rojos no se utilizan.
3 Use un cable de vídeo estándar para conectar la toma de salida de vídeo del STB a la toma de entrada de
vídeo del televisor.
4 Ajuste el interruptor selector de resolución a la posición "480i."
5 Después de completar la conexión al televisor, conecte el cable de alimentación de CA del televisor a la
toma de CA y encienda el televisor.
6 Ponga el televisor en el modo de entrada.
NOTA:
Para más información, consulte el manual de instrucciones de su televisor.
7 Conecte el cable de alimentación de CA del STB a la toma de CA y luego encienda el STB.
NOTA:
Si se utiliza un cable de vídeo estándar para realizar la conexión, la resolución de la señal de vídeo de salida
siempre será 480i.
93
Download from Www.Somanuals.com. All Manuals Search And Download.
ES
Guía para rápida consulta
Configuración inicial
1 Aparecerá el SETUP WIZARD.
ASISTENTE PARA LA CONFIGURACIÓN
(SETUP WIZARD)
El SETUP WIZARD es un práctico menú que le
ayuda hacer los ajustes iniciales del STB.
2 Seleccione SETUP utilizando los
botones de navegación s / B y, a
continuación, presione ENTER.
•
Aparecerá la pantalla SETUP WIZARD 1/8.
Cuando se enciende el STB por primera vez después
de conectar el cable de alimentación de CA, el
SETUP WIZARD aparece automáticamente en la
pantalla. En este menú se pueden configurar los
siguientes ítems para el ajuste inicial del equipo.
3 Seleccione el idioma deseado
utilizando los botones de navegación
o
/
p y, a continuación, presione ENTER.
•
•
El idioma seleccionado se activará.
Aparecerá la pantalla SETUP WIZARD 2/8.
•
•
•
•
•
•
•
Idioma para la pantalla
Búsqueda de canales
Horario de ahorro de luz diurna (DST)
Zona horaria
Año/ fecha/ hora
Reloj
4 El STB comienza a buscar canales.
•
•
Espere hasta que la exploración finalice.
Cuando la exploración finalice, se visualizará
"100%" en el cuadro y luego aparecerá la pantalla
siguiente.
Formato de la pantalla y modo de visualización
Para omitir la exploración:
Presione ENTER.
5 Aparecerá la pantalla SETUP WIZARD
3/8.
6 Seleccione ON u OFF para Horario de
ahorro de luz diurna (DST) utilizando
los botones de navegación s / B y, a
continuación, presione ENTER.
8
1,2,3,6,7,
8,9,10,11,
12,13
•
Aparecerá la pantalla SETUP WIZARD 4/8.
7 Seleccione la zona horaria deseada
utilizando los botones de navegación
o
/
p / s / B y, a continuación, presione
1,2,3,6,7,
8,10,12,
13
ENTER.
•
Aparecerá la pantalla SETUP WIZARD 5/8.
NOTA:
Consulte "INFORMATION on Time Zone
(INFORMACIÓN sobre las zonas horarias)" en la
página 61.
94
Download from Www.Somanuals.com. All Manuals Search And Download.
ES
Guía para rápida consulta
8 Introduzca el año (YEAR), fecha (DATE) 11 Presione ENTER.
•
Aparecerá la pantalla SETUP WIZARD 7/8.
y hora (TIME) utilizando los botones de
navegación o / p / s / B o los botones
numéricos.
12 Seleccione el formato de pantalla
deseado utilizando los botones de
navegación o / p y, a continuación,
presione ENTER.
•
•
Cada vez que introduzca un número, presione
ENTER para mover el cursor.
Si desea retroceder o avanzar, presione los
botones de navegación s / B para mover el
cursor.
•
Aparecerá la pantalla SETUP WIZARD 8/8.
NOTA:
NOTA:
Para más información, consulte la sección "Selecting
screen formats (Selección de formatos de pantalla)"
en la página 54.
Una vez que haya introducido toda la información, el
cursor se moverá a SET.
RECOMENDACIÓN:
13 Seleccione el modo de visualización
deseado utilizando los botones de
navegación o / p y, a continuación,
presione ENTER.
Para ajustar el año (YEAR), introduzca los 2 últimos
dígitos del año. El año quedará registrado. (Por
ejemplo, si introduce "03" con los botones
numéricos, se visualizará 2003.)
•
Esto completa el procedimiento del SETUP
WIZARD.
El STB comenzará a recibir emisiones.
9 Cuando el cursor se encuentre en SET,
presione ENTER.
•
•
Los ajustes realizados se activarán.
Aparecerá la pantalla SETUP WIZARD 6/8 y el
STB comenzará a buscar canales con "ajuste
automático de reloj" para mantener la hora
correcta.
NOTA:
Para más información, consulte la sección "Selecting
screen formats (Selección de formatos de pantalla)"
en la página 54.
10 Seleccione el canal deseado en el
mapa de canales utilizandolos botones
de navegación o / p.
NOTA:
Los números de los canales que contienen datos de
reloj cambiarán a color negro en el mapa de canales.
NOTA:
: Indica que hay más canales hacia arriba o hacia
abajo.
: Indica el límite superior o inferior del mapa de
canales.
Si no desea usar la función de ajuste
automático de reloj:
Seleccione OFF en el mapa de canales y presione
ENTER.
RECOMENDACIÓN:
OFF se encuentra en el extremo superior del mapa de
canales. Presione repetidamente el botón de
navegación o para desplazarse a esta posición.
95
Download from Www.Somanuals.com. All Manuals Search And Download.
ES
LIMITED WARRANTY
FUNAI CORP. will repair this SYLVANIA product, free of charge in the USA in the event of defect in materials or
workmanship as follows:
DURATION:
PARTS:
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the
date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this
warranty.
LABOR:
FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date
of original retail purchase.
LIMITS AND EXCLUSIONS:
This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail
purchase will be required together with the product to obtain service under this warranty.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing or
if service was attempted by an unauthorized service center. This SYLVANIA Limited warranty does not apply to any
product not purchased and used in the United States.
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It
does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not
supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication,
alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this
product or damage which results from fire, flood, lightning or other acts of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE
CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY
GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE
USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF
FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY, AND
FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS
REPRESENTATIVES IN THE UNITED STATES. ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE
PERFORMED BY A FUNAI AUTHORIZED SERVICE CENTER. THIS WARRANTY IS VALID WHEN THE
UNIT IS CARRIED-IN TO FUNAI AUTHORIZED SERVICE FACILITY.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS
THAT VARY FROM STATE TO STATE, IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE
UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI
CORP.
ATTENTION:
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT
WITHOUT PRIOR NOTICE.
To locate your nearest SYLVANIA Authorized Service Center or for general service procedure,
please call 1-800-968-3429 or write to the following:
FUNAI CORPORATION, INC.
SERVICE CENTER
19900 Van Ness Avenue, Torrance, CA 90501
Tel :1-800-968-3429
Head Office: 100 North Street, Teterboro, NJ 07608
PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.
ST201UB
0EMN02308 *****
Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
|