5
8
Made In The
8 8
8 5
5
U S A
Download from Www.Somanuals.com. All Manuals Search And Download.
··
·
Exercise special care when mowing around fixed objects
in order to prevent the blades from striking them. Never
deliberately run tow vehicle or mower onto or over any
foreign object.
·
·
Use mower only as the manufacturer intended and as
described in the manual.
Do not operate mower if it has been dropped or damaged
in any manner. Always have damage repaired before
using your mower.
·
·
·
Dress properly. Do not operate mower when barefoot or
wearing open sandals. Wear only solid shoes with good
traction when mowing.
Always make cutting height adjustments before starting
your mower. Never attempt to do this while the engine is
running.
Keep your eyes and mind on your mower and the area
being cut.
Do not let other interests distract you.
Do not put hands or feet near or under rotating parts.
Keep clear of the discharge opening at all times.
Before cleaning, inspecting, or repairing your mower,
stop the engine and make absolutely sure the blade and all
moving parts have stopped. Then disconnect the spark
plug wire and keep it away from the spark plug to prevent
accidental starting.
Do not operate your mower if it vibrates abnormally.
Excessive vibration is an indication of damage; stop the
engine, safely check for the cause of vibration and repair
as required.
ALWAYS DISCONNECT SPARK PLUG
WIRE AND PLACE IT WHERE IT CANNOT
CONTACT SPARK PLUG IN ORDER TO
PREVENT ACCIDENTAL STARTING WHEN
SETTING UP, TRANSPORTING, ADJUSTING
OR MAKING REPAIRS.
·
·
·
·
·
Read, understand, and follow all instructions in the
manual and on the machine before starting.
Read this operator's manual carefully. Become familiar
with the controls and know how to operate your mower
properly.
Only allow responsible adults who are familiar with the
instructions to operate the machine.
Clear the area of objects such as rocks, toys, wire, etc.
which could be picked up and thrown by the blade.
Be sure the area is clear of other people before mowing.
Stop machine if anyone enters the area.
·
·
·
·
·
·
Never operate your mower without proper guards, plates,
or other safety devices in place.
Do not attempt to operate the tow vehicle when not in
drivers seat.
·
·
Never carry passengers.
Do not mow in reverse unless absolutely necessary.
Always look down and behind before and while backing.
Be aware of the mower discharge direction and do not
point it at anyone. Do not operate the mower without the
guards in place.
·
Slopes are a major factor related to loss-of-control and tip over
accidents, which can result in severe injury or death. All
slopes require extra caution. If you feel uneasy on it, do not
mow it.
·
·
Slow down before turning.
Never leave a running machine unattended. Always turn
off blades, and stop engine.
·
·
·
Turn off blades when not mowing.
Mow only in daylight or good artificial light.
Do not operate the machine while under the influence of
alcohol or drugs.
Watch for traffic when operating near or crossing
roadways.
Use extra care when loading or unloading the machine
into a trailer or truck.
Disengage power to mower and stop engine when
·
·
·
Mow up and down slopes.
Remove obstacles such as rocks, tree limbs, etc.
Watch for holes, ruts, or bumps; uneven terrain could
overturn the machine; tall grass can hide obstacles.
Use slow speed. Choose a low gear so that you will not
have to stop or shift while on the slope.
Keep all movement on the slopes slow and gradual. Do
not make sudden changes in speed or direction.
·
·
·
·
·
transporting or not in use.
Download from Www.Somanuals.com. All Manuals Search And Download.
·
Avoid starting or stopping on a slope. If tires lose
traction, disengage the blades and proceed slowly straight
down the slope.
·
·
·
Stop and inspect the equipment if you strike an object.
Repair, if necessary, before restarting.
Never make adjustments or repairs with the engine
running.
Mower blades are sharp and can cut. Wrap the blade(s) or
wear gloves, and use extra caution when servicing them.
Do not turn on slopes unless necessary, and then, turn
slowly and gradually downhill, if possible.
Do not mow near drop-offs, ditches, or embankments.
The mower could suddenly turn over if a wheel is over
the edge of a cliff or ditch, or if an edge caves in.
Do not mow on wet grass. Reduced traction could cause
sliding.
III.
TRAGIC ACCIDENTS CAN OCCUR IF
THE OPERATOR IS NOT ALERT TO
THE PRESENCE OF CHILDREN.
CHILDREN ARE OFTEN ATTRACTED
TO THE MACHINE AND THE MOWING
ACTIVITY. NEVER ASSUME THAT
CHILDREN WILL REMAIN WHERE YOU
LAST SAW THEM.
Keep children out of the mowing area and under the
watchful care of another responsible adult.
Be alert and turn machine off if children enter the area.
Before and when backing, look behind and down for
small children.
Never carry children. They may fall off and be seriously
injured or interfere with safe machine operation.
Never allow children to operate the machine.
Use extra care when approaching blind corners, shrubs,
trees, or other objects that may obscure vision.
·
·
·
Use extra care handling gasoline and other fuels. They
are flammable and vapors are explosive.
-
-
Use only an approved container.
Never remove gas cap or add fuel with the engine
running.
-
Allow engine to cool before refueling. Do not
smoke while refueling.
-
-
Never refuel the machine indoors.
Never store the machine or fuel container inside
where there is an open flame, like that of a water
heater.
·
·
Never run a machine inside a closed area.
·
·
Never tamper with safety devices. Check their proper
operation regularly.
Keep machine free of grass, leaves, or other debris build-
up; clean oil or fuel spillage; allow machine to cool before
storing.
Download from Www.Somanuals.com. All Manuals Search And Download.
Replace decal immediately if damaged. Order by part number from
Swisher Mower and Machine Co. Inc.
D55-DANGER DECAL
D20-CAUTION DECAL
D30-WARNING DECAL
D28-OFF/ON DECAL
D10-ENGAGE DECAL
D99116-MED. SILVER LOGO DECAL
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Replace decal immediately if damaged. Order by part number from
Swisher Mower and Machine Co. Inc.
D82-44 RUGGED CUT DECAL
D29- DANGER DECAL
Download from Www.Somanuals.com. All Manuals Search And Download.
TRAGIC ACCIDENTS CAN OCCUR IF THE OPERATOR IS NOT ALERT TO THE PRESENCE OF
CHILDREN. CHILDREN ARE OFTEN ATTRACTED TO THE MACHINE AND THE MOWING
ACTIVITY. NEVER ASSUME THAT CHILDREN WILL REMAIN WHERE YOU LAST SAW THEM.
·
·
Move blade clutch lever to disengaged (vertical) position.
Turn key switch to OFF position.
·
·
·
Place cutter behind tow vehicle and back up to it for
attaching.
Slide tow bar of cutter over the tow vehicles hitch so that
holes line up.
Insert hitch pin until it extends through the bottom of the
tow bar.
This trail mower has been designed to run offset from the
center of the tow vehicle in order to make the unit more
flexible in a wide range of mowing situations.
·
·
·
The adjustable tow hitch of this mower can be assembled
from straight behind the tow vehicle to approximately 20”
offset to either side
·
·
Place safety latch over the end of the hitch pin.
Secure control console to tow vehicle, making sure it can
be reached from the operating position (see pre-assembly
instructions. Use provided Velcro straps to secure control
cable to cutter frame, hitch, and tractor.
(refer to fig. 1)
Install hitch tube (2) over the front torsion bar (1) on
mower (Note: the hitch tube can be placed anywhere
along the length of the torsion bar). Secure the hitch tube
in place using four 3/8-16 x 2 ½ bolts (4) and 3/8 -16
nyloc nuts (5).
Install the “L” hitch (3) into the hitch tube, and loosely
secure with two 5/16-18 x 2 12 bolts (6) and 5/16-18
nyloc nuts (7). The “L” hitch will be secured in place
after the front to back adjustment has been determined
(see next step).
·
·
·
Disengage the blade.
Shut off cutter engine.
Place cutter deck in the highest position.
SHUT OFF MOWER ENGINE AND REMOVE
SPARK PLUG WIRE FROM SPARK PLUG
BEFORE MAKING ANY ADJUSTMENTS TO
THE MOWER.
To obtain the best cutting results, the mower deck should be
adjusted so that it is parallel to the ground. To check front to
back adjustment, measure from the bottom edge of the deck to
the ground at both the front and rear of the deck. This next
series of instructions is best done with the mower and tow
vehicle together.
The cutting height range of this unit is from approximately 2
1/2 to 6 inches. Heights are measured from the ground to the
blade tip with the engine not running. Rotate height
adjustment crank handle in a clockwise direction to raise the
cutter and in a counter clockwise direction to lower.
·
Install the hitch swivel (8) to the tow bar of the tow
vehicle. (refer to fig. 1)
·
Raise the hitch tube of the mower until the bottom of the
deck is parallel to the ground. Note the position of the
clevis on the “L” hitch in relation to the hitch swivel on
the tow vehicle. The “L” hitch will have to be moved up
or down to match this height.
·
·
Fill engine with oil (see engine manual for proper
procedure and requirements).
Add gasoline. Fill fuel tank using fresh clean unleaded
gas.
·
Set the mower back on the ground, remove the hardware,
slide the “L” hitch into the predetermined position, and
reinstall the nuts and bolts. The hardware can now be
tightened.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
·
Start engine, engage blade control to start blades rotating
and allow blades to rotate for approximately five minutes
to break in mower and engine.
FILL TO BOTTOM OF FUEL TANK FILLER
NECK.DO NOTOVERFILL WIPE OFF
SPILLED OIL OR FUEL. DO NOT
STORE, SPILL, OR USE GASOLINE NEAR
OPEN FLAME.
·
·
·
Starting the engine: To start the engine, be sure that the
blade control lever is in the disengaged (vertical) position.
Turn key switch to the start position.
Engaging the blade: Move lever from the disengaged
(vertical) position down to the engaged (horizontal)
position.
Disengaging the blade: Move the lever from the engaged
(horizontal) position up to the disengaged (vertical)
position.
KEEP THE BLADE CLUTCH LEVER IN
“DISENGAGED” POSITION WHEN
STARTING ENGINE.
·
·
Make sure spark plug wire is properly connected.
Place throttle control in “CHOKE” position if the engine
is cold. A warm engine may not require choking to start.
Grasp starter handle with one hand. Pull rope out slowly
until engine reaches start of compression cycle (rope will
pull slightly harder at this point).
·
·
Pull rope with a rapid, continuous, full arm stroke. Keep
a firm grip on starter handle and let rope rewind slowly.
Do not let starter handle snap back against starter.
When engine starts, move throttle control to the “RUN”
position (full throttle).
·
·
Move blade clutch lever to disengaged (vertical) position.
Turn key switch to OFF position.
·
·
Allow engine to warm up for a few minutes before
engaging blades.
Note: If at a high altitude (above 3000 feet) or in cold
Temperatures (below 32F), the carburetor fuel
mixture may need to be adjusted for best
performance (see Service and Adjustments section of
the engine manual.)
NEVER CARRY CHILDREN. THEY MAY
FALL OFF AND BE SERIOUSLY INJURED
OR INTERFERE WITH SAFE OPERATION.
·
·
Mowing should be started with the tow vehicle in low
gear and speed increased only as mowing conditions will
safely permit. This speed should not exceed 3 ½ mph.
Better mowing results will be obtained in those areas with
the least amount of growth. While your mower will cut
through dense growth, you will experience a substantial
increase in the horsepower required and some change in
the finished appearance as compared to those areas with
the least amount of growth.
CHECK AREA UNDER AND AROUND
MOWER FOR ANY OBJECTS THAT COULD
BE THROWN FROM UNDER MOWER.
MAKE SURE THAT MOWER DISCHARGE
AREA IS CLEAR.
·
Mowing conditions will vary from place to place,
including the types of grass and brush that are being
mowed. When mowing tall grass and brush you may find
that the pressure of the wheel tracks may cause certain
grasses and brush to be pushed downward and will not be
mowed properly. If this condition exists you may have to
mow the area twice, the first mowing with the mower
raised and the second mowing at the normal height that
you have chosen. If it is practical, better results will be
found if the second mowing is at a right angle in travel to
the previous mowing.
TRAGIC ACCIDENTS CAN OCCUR IF
THE OPERATOR IS NOT ALERT TO
THE PRESENCE OF CHILDREN.
CHILDREN ARE OFTEN ATTRACTED
TO THE MACHINE AND THE MOWING
ACTIVITY. NEVER ASSUME THAT
CHILDREN WILL REMAIN WHERE YOU
LAST SAW THEM.
Break in your belts, pulleys, and engine before you actually
begin mowing for the first time.
·
When mowing thick grass and brush you will find that the
performance of the mower will be greatly improved if the
Download from Www.Somanuals.com. All Manuals Search And Download.
speed of travel is reduced. This allows the mower the
time necessary to make its initial cut, and then the
subsequent cuts that chop the materials into small pieces
to be discharged properly. Failure to do this will result in
a poor finished look and the possibility of stalling the
engine.
Do not mow grass when it is wet. Wet grass will
accumulate under the mower deck and leave undesirable
clumps. Allow grass to dry before mowing.
·
·
Always operate mower engine at full throttle when
mowing to assure the best mowing performance and
proper discharge of material. Regulate ground speed by
selecting a low enough gear to give the mower cutting
performance as well as the quality of cut desired.
When mowing extremely dense brush and saplings, do
not attempt to mow over any area that the tow vehicle
·
cannot
maneuver
through.
The warranty on this cutter does not cover items that have been subjected to operator abuse or negligence. To receive full value from
the warranty, operator must maintain unit as instructed in this manual.
Some adjustments will need to be made periodically to maintain your unit properly.
All adjustments in the service and adjustments section of this manual should be checked at least once each season.
·
·
·
Replace the spark plug.
Clean or replace the air filter.
Check blades and belts for wear.
A new spark plug and clean air filter assure proper air-fuel mixture and help your engine run better and last longer.
·
·
·
·
Check engine oil level. (Do this twice to insure an accurate reading.)
Check condition of air filter and clean or replace if necessary.
Check blade operation.
Check for loose fasteners.
Make sure all nuts and bolts are tight and cotter pins and retainer springs are secure. Keep blades sharp. Observe all safety
precautions.
For best results cutter blades must be kept sharp. The blades can be sharpened with a few strokes of a file or grinding wheel. Do Not
attempt to sharpen while on the cutter.
DO NOT HANDLE MOWER BLADES WITH
BARE HANDS. CARELESS OR IMPROPER
HANDLING MAY RESULT IN SERIOUS
INJURY.
Your cutter has been produced with components designed for your unit. Although standard V-belts, bearings, blades, pulleys, etc.
may look like parts used elsewhere, many are of a different construction and could, in some cases cause a malfunction in the operation
of the machine.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
4846
B527
BB105
Download from Www.Somanuals.com. All Manuals Search And Download.
ITEM #
PART #
4865
DESCRIPTION
DECK WELDMENT
5/16-18 X 1 1/4 FLNGE BOLT
5/16-18 FLNGE NUT
ITEM #
30
31
PART #
6681
DESCRIPTION
IDLER ARM
1
2
NB-253
NB-181
WHRT44TEC
WHRT44BS
NB-504
NB-181
4853
NB-588
NB-121
NB-281
NB-250
NB-180
9023
1/2-13 X 2 1/2 BOLT
1/2-13 TWO-WAY LOC NUT
1/2-13 NYLOC NUT
1/4-20 X 3/4 BOLT
1/4-20 NYLOC NUT
CLEVIS U-CLIP
4
4
5
WIR HRNES-TEC
WIR HRNES-BRIGGS&STRTON
5/16-18 X 1 1/4 BOLT
5/16-18 FLNGE NUT
32
33
34
35
36
6
7
8
RUBBER FLAP STRAP
RUBBER FLAP
1/2-13 X 1 1/2 BOLT
1/2-13 NUT
1/2-13 NYLOC NUT
4839
682S
BELT ENGAGE ARM
IDLER SPRING
1/4-20 X 1 BOLT
4843
NB-617
NB-213
NB-281
6745
NB-114
NB-238
NB-216
4836
NB-596
NB-170
4834
NB-195
4844
NB-126
4864
4860
NB-107
NB-182
T2PB
NB-596
NB-170
4850
NB-102
NB-139
NB-180
NB-501
NB-181
NB-556
B99S
1/4-20 NUT
1/4-20 NYLOC NUT
5/16-18 X 1 FLNGE BOLT
5/16-18 NYLOC NUT
5/16 FLAT WASHER
SPACER
9
10
11
LONG EYEBOLT
37
1/2-20 X 1/2 SELF-TAPPING BOLT
3/8-24 X 1 ENG BOLT
3/8-24 TWO-WAY LOC NUT
MOTOR BASE
12
13
38
39
40
BT35
682S
3 LINK CHAIN
IDLER SPRING
5/16-18 X 3/4 FLNGE BOLT
5/16-18 FLNGE NUT
TIRE/WHEEL ASSEMBLY
13/16 X 1 1/4 X 1/8 WASHER
PULLEY COVER
NB-619
NB-212
NB-280
NB-194
BP370S
BP370
BT297
B527
3/8-16 X 2 1/2 BOLT
3/8-16 NUT
3/8-16 TWO-WAY LOC NUT
1/4 NYLON WASHER
BRAKE PAD CLIP
BRAKE PAD
14
15
16
17
18
19
20
1/8 X 1 COTTER PIN
41
42
43
44
45
46
HEIGHT ADJUSTMENT BAR
REAR TORSION BAR
3/8-16 X 1 1/2 BOLT
BRAKE SPRING
IDLER PULLEY
T HANDLE
3/8-16 NYLOC NUT
4463
3/8 PLASTIC BUSHING
5/16-18 X 3/4 FLNGE BOLT
5/16-18 FLNGE NUT
TOP HEIGHT ADJUST SECTION
3/8-16 X 1 1/4 BOLT
3/8-16 TWO-WAY LOC NUT
1/4-20 X 1 1/2 BOLT
1/4-20 NYLOC NUT
BLACK PLASTIC KNOB
CRANK HANDLE
NB-560
NB-180
NB-591
NB-181
KSM
1/4-20 X 1 1/4 BOLT
1/4-20 NYLOC NUT
5/16-18 X 1 1/2 TORX BOLT
5/16-18 NYLOC NUT
KEY SWITCH
21
47
22
23
NB-618
NB-280
NB-104Z
NB-180
4857
48
49
50
4852
ENGAGE CONSOLE MOUNT PLATE
1/4-20 X 2 1/2 BOLT
1/4 SAE WASHER
1/4-20 WING NUT
3/32 X 3/4 COTTER PIN
1/4 SAE WASHER
1/4 X 1 1/2 CLEVIS PIN
T HANDLE LINK
24
NB-141
NB-274
NB-608
NB-597
NB-274
NB-518
4461
4847
4805
4809(L&R)
BR20CC
BA50
25
26
27
4874
4851
51
BOTTOM HEIGHT ADJUST SECTION
5/16-18 X 1/2 FLNGE BOLT
AUXILARY PULLEY COVER
3/8-16 X 2 1/2 BOLT
NB-252
4837
NB-619
NB-212
NB-182
28
29
52
53
54
ENGAGE CONSOLE
FRONT TORSION BRACKETS
REAR TORSION BRACKETS
ENGAGE CABLE
3/8-16 NUT
3/8-16 NYLOC NUT
55
NOT SHOWN
NOT SHOWN
BELT
Download from Www.Somanuals.com. All Manuals Search And Download.
Each mower has its own model number. Each engine has its
own model number. The model number for the mower will be
found on the right hand side of the drive belt housing. The
model number for the engine will be found on the top of the
blower fan housing.
All mower parts listed herein may be ordered directly from
Swisher Mower & Machine Co. Inc. or your nearest Swisher
dealer.
All engine parts may be ordered from the nearest dealer of the
engine supplied with your mower.
5
WHEN ORDERING PARTS, PLEASE HAVE THE
FOLLOWING INORMATION AVAILABLE:
8
* PRODUCT - TRAILMOWER
* SERIAL NUMBER - _______________
* MODEL NUMBER - _______________
* ENGINE MODEL NUMBER - _______________
TYPE - _______________
* PART NUMBER
* PART DESCRIPTION
TELEPHONE - 1-800-222-8183
FAX - 1-660-747-8650
1602 CORPORATE DRIVE P.O. BOX 67
WARRENSBURG, MO 64093
SWISHER MOWER & MACHINE CO. INC.
PRINTED IN U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Sharp Stereo System XL S10 User Manual
Snapper Lawn Aerator 4568 User Manual
Sony Speaker System CMT V10iPN User Manual
SOYO Computer Hardware SY 6ZB User Manual
SportDOG Pager DSL 400 User Manual
Stiga Baby Carrier 8211 0276 08 User Manual
Stiga Lawn Mower 13 2715 16 User Manual
Sunbeam Blood Pressure Monitor 7682 User Manual
Swann Security Camera SW215 DMD User Manual
TANDBERG Security Camera 75 MXP User Manual