®
Oskar Mini
3 cup food processor
Instruction Booklet
LC3200
Please read these instructions carefully
and retain for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Sunbeam’s Safety Precautions
Features of your Sunbeam Oskar® Mini
Attachments for your Sunbeam Oskar® Mini
Using your Sunbeam Oskar® Mini
Fitting/using the tools on your Oskar® Mini
Storing your Sunbeam Oskar® Mini
Handy hints for processing
4
6
8
9
11
13
15
17
18
Care and cleaning
Recipes
Important instructions – retain for
future use.
Download from Www.Somanuals.com. All Manuals Search And Download.
Sunbeam’s Safety Precautions
Sunbeam is very safety conscious when
designing and manufacturing consumer products,
but it is essential that the product user also
exercise care when using an electrical appliance.
Listed below are precautions which are essential
for the safe use of an electrical appliance:
• Read carefully and save all the instructions
provided with an appliance.
• Do not use an appliance for any purpose
other than its intended use.
• Do not place an appliance on or near a hot gas
flame, electric element or on a heated oven.
• Do not place on top of any other appliance.
• Do not let the power cord of an appliance hang
over the edge of a table or bench top or touch
any hot surface.
• Always turn the power off at the power outlet
before you insert or remove a plug. Remove
by grasping the plug - do not pull on the cord.
• Turn the power off and remove the plug
when the appliance is not in use and
before cleaning.
• Do not use your appliance with an extension
cord unless this cord has been checked
and tested by a qualified technician or
service person.
• Always use your appliance from a power
outlet of the voltage (A.C. only) marked
on the appliance.
• This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
• Do not operate any electrical appliance with
a damaged cord or after the appliance has
been damaged in any manner. If damage is
suspected, return the appliance to the nearest
Sunbeam Appointed Service Centre
for examination, repair or adjustment.
• For additional protection, Sunbeam
recommend the use of a residual current
device (RCD) with a tripping current not
exceeding 30mA in the electrical circuit
supplying power to your appliances.
• Do not immerse the appliance in water
or any other liquid unless recommended.
• Appliances are not intended to be operated
by means of an external timer or separate
remote control system.
• This appliance is intended to be used in
household and similar applications such
as: staff kitchen areas in shops, offices and
other working environments; farm houses; by
clients in hotels, motels and other residential
type environments; bed and breakfast type
environments.
• Children should be supervised to ensure that
they do not play with the appliance.
• The temperature of accessible surfaces may be
high when the appliance is operating.
• Never leave an appliance unattended while
in use.
If you have any concerns regarding the performance and use of your appliance,
Ensure the above safety precautions are understood.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Sunbeam’s Safety Precautions
SAFETY PRECAUTIONS FOR YOUR
SUNBEAM FOOD PROCESSOR LC3200.
• All blades and attachments should be
removed with care before cleaning.
• Always use extreme care when handling
processing blades and cutting discs. These
are extremely sharp and may cause injury if
handled incorrectly. Always store processing
blades and cutting discs in their respective
covers or processing containers.
• Do not over fill the processor.
• Do not exceed the max indicator 3 cups /
750mL when processing dry ingredients.
• Do not exceed the liquid max indicator
2 cups/500mL when processing liquids.
• Do not process for longer than the time
periods recommended in the operating
chart.
• Unplug from power outlet when not in use,
before putting on or taking off attachments,
and before cleaning.
• Always remove the blade before emptying
the processor bowl of its contents.
• Do not put hot liquids or ingredients into the
food processor bowl. Allow to cool to room
temperature prior to processing.
• Do not operate this food processor for more
than 10 seconds using heavy loads. None
of the recipes in this instruction booklet are
considered to be heavy loads.
• Avoid contacting moving parts at all times.
• Place the processor bowl onto the base of
the processor before fitting any attachments.
Important instructions – retain for
future use.
If you have any concerns regarding the performance and use of your appliance,
Ensure the above safety precautions are understood.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Features of Your Sunbeam
®
Oskar Mini
Processing cover
The processing cover activates the automatic
safety system. The Oskar® Mini will not operate
unless the cover is correctly positioned on the
processing bowl and locked into place.
600 watt motor
The base houses a 600 watt motor, which
provides consistent processing results.
On / off button
For easy use the large ON / OFF button starts
and stops the operation of the food processor.
Pulse
The 'Pulse' feature allows for total control over
processing tasks.
Storage drawer
Unique drawer design enables attachments to be
stored conveniently within the appliance when
not in use.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Food pusher
Assists in guiding food through the chute
to ensure food hits the blade vertically for
best processing results. The food pusher also
doubles as a measuring cup.
Feed tube
The feed tube is used to guide ingredients
down into the selected blades and allows you
to add ingredients during other processing
tasks.
Spindle
Drives all the food processing attachments.
The spindle must be in place to operate the
food processor.
Processing bowl
The processing bowl achieves a 3 cup / 750mL
processing capacity for dry ingredients and a
2 cup / 500mL capacity for liquids.
Cord storage facility
For added convenience the unused cord length
can easily be pushed into the base of the
processor for storage.
Non-slip feet
Keeps the food processor secure on the bench
top during use.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Attachments for your Sunbeam
®
Oskar Mini
1. Processing blade
3. Reversible shredding disc - fine and coarse
Stainless steel smooth edged processing blade
is designed for cutting, kneading, whisking and
emulsifying.
Ideal control, the reversible stainless steel
shredding blades allow for the choice of fine
or coarse results.
2. Reversible slicing blade - thick and thin
The reversible stainless steel slicing blade
allows both thick & thin slicing.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Using your Sunbeam Oskar
Mini
Before using your Oskar® Mini
3.Rotate the handle clockwise to lock, as
indicated by the graphics on the left side
of the motorbase, see figure 2.
• Wash the processing bowl, cover and all
attachments in warm water using a mild
detergent. Dry each part thoroughly
before use.
• Before you assemble the food processor,
ensure that the power cord is unplugged.
1.Place the motor base facing you on a dry,
level surface.
2.Place the processing bowl onto the motor
base, the bowl will only sit correctly on the
base when the handle is positioned to the
right, see figure 1.
Fig 2
4.Position the lid onto the processing bowl
You will notice a solid grey arrow � to
.
the left of the holding lip on the lid, when
placing the lid onto the bowl this arrow
needs to align with the solid grey arrow �
on the handle of the bowl. To lock, turn the
lid clockwise, as indicated by the graphics,
on the top of the handle, see figure 3.
Fig 1
Fig 3
9
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Using your Sunbeam Oskar Mini continued
Important: If the processing bowl and cover
are not correctly assembled, the Oskar® Mini
will not function.
3.After you have completed processing, press
the On/Off button to stop processing.
Note: For maximum control when using your
food processor, before turning on your food
processor load the feed tube. Always use the
food pusher for more evenly processed foods
and never use your fingers.
Using your Oskar® Mini
1.Plug the power cord into a 230-240V AC
power outlet and turn the power ‘ON’.
2.Using the On/Off button on the control
panel, press once to start processing.
The Pulse function remains on as long as the
Pulse button is pressed down.
Important: The Oskar® Mini is fitted with
a safety thermal cut-out device and will
shut off in the event of overload. If this
occurs, switch the appliance off and it will
automatically reset when cool.
Further ingredients can also be added while
processing by pouring through the feed tube
once the food pusher has been removed.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Fitting/using the tools on your
®
Oskar Mini
Note: All attachments must be firmly
attached to the spindle. Always adjust the
attachments until you are sure that they are
correctly fitted.
Warning: Use caution, as blades are sharp.
Always handle the processing blade by its
central plastic section.
4.Place food into the processing bowl.
5.Fit the processing cover to the processing
bowl, see figure 3 and place the food
pusher in the feed tube.
6.Plug the power cord into a 230-240V AC
power outlet and turn the power ‘ON’.
Placing the spindle
1.Fit the spindle onto the drive shaft and
ensure the blade locks into place, see
figure 4.
7.Start processing using the On/Off or Pulse
buttons.
8.When processing is complete, remove the
spindle and blade from the processing bowl
before removing the processed food.
Fig 4
Processing blade
1.Fit the processor bowl and spindle as
detailed previously in figures 1, 2 & 4.
2.Fit the processing blade over the spindle
and press firmly into place, see figure 5.
Fig 5
11
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Fitting/using the tools on your Oskar Mini continued
Reversible grating, or slicing blades
1.Fit the processor bowl and spindle as
detailed previously, in figures 1, 2 and 4.
2.Select the 'Reversible' disc of your choice
- Shredding (fine or coarse), Slicing (thin or
thick).
3.Fit the disc over the spindle and press
firmly into place, see figure 6.
Warning: Use caution as the blades are sharp.
Fig 6
4.Fit the processing cover to the processing
bowl as previously shown in figure 3 and
place the food pusher in the feed tube.
5.Plug the power cord into a 230-240V AC
power outlet and turn the power ‘ON’.
6.Start processing using the On/Off button.
7.When processing is complete, remove the
disc and spindle from the processing bowl
before removing the processed food.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Storingyour Sunbeam Oskar Mini
The Sunbeam Oskar® Mini was designed so
that all attachments can be stored
within the unit itself, see figure 8.
3.Place one of the 'Reversible Shredding
discs' in storage drawer as indicated in
figure 10.
Fig 10
Fig 8
Storage drawer
The ‘Reversible Slicing blade’ and 'Reversible
Shredding' disc, are both stored in the
storage drawer.
1.Slide out the storage drawer at the base of
the food processor.
2.Place the reversible slicing blade in the
storage drawer as indicated in figure 9.
Fig 9
13
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Storing your Sunbeam Oskar Mini continued
Cord storage
The power cord can be stored by pushing it
into the back of the motor base, see
figure 11.
Fig 11
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Handyhints for processing
Liquid Max Indicator
Note: When processing sauces or semi-liquid
ingredients, stop the food processor and
scrape down the container sides.
The processing bowl can be filled up to the
max 3 cup / 750mL indicator for processing
dry ingredients only. For processing liquids
do not fill past the liquid max 2 cup / 500mL
indicator.
Using the Feed Tube
The most important factor for successful
slicing and shredding is the way in which the
food is placed into the feed tube.
Note: Do not process water in this food
processor.
Chopping
When slicing, shredding and grating
For the best, most consistent results, you
should try to process pieces of food that are
approximately equal in size. When you break,
cut or tear food into uniform pieces before
you begin processing, the finished results will
be more uniform.
Cut all ingredients to a size that fits
comfortably into the feed tube. Pack the
feed tube and, while holding food steady
and upright with the food pusher, press
down evenly until all ingredients are sliced
or shredded. The more firmly you push,
the thicker the slices or shreds. Do not use
excessive force or you may damage the food
processor.
More consistent processing results are
achieved if the container is not overloaded.
Mincing
Pre-cut meat into cubes approximately 2cm
square.
Note: Never use fingers to push food down
the feed tube. Always use the food pusher.
Vegetables
For best results when slicing.
When processing vegetables such as onions,
peel and quarter or cut large vegetables into
eighths.
The feed tube should always be packed firmly
to allow each piece of food to support the
others. There will always be a small portion
of food left unprocessed between the food
pusher and the blade.
Mixing
The quantities that can be processed within
the Processing bowl will vary with the density
of the mixture.
Adding Ingredients
When various recipes require dry ingredients
such as flour, add them directly into the
processing bowl before processing. There
is no need to sift ingredients when using
your food processor. Liquid ingredients may
be added while the processor is operating
by pouring through the feed tube in the
processor cover.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Handy hints for processing continued
Preparation for slicing foods
For best results when shredding and grating
Pack the food items vertically in the feed tube,
see figure 12.
Remember that softer foods such as cheese
(cheddar, mozzarella or swiss) should be well
chilled before processing. Harder foods such
as parmesan or Romano cheese should be at
room temperature before processing.
Note: When grating parmesan cheese do not
apply a lot of pressure to the food pusher.
Disassembly
When processing is completed, remove the
cover from the processing bowl first and
then remove the processing bowl with the
processing blade still in place.
To remove the processing bowl firstly unlock
the processing cover by rotating it in a
anti-clockwise direction until the cover is
unlocked.
Note: Always wait for the blades to stop
moving completely before removing the cover.
Fig 12
Warning: Use extreme caution, as blades are
sharp. Always handle the processing blade by
its central plastic section.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Careand cleaning
When you have finished processing, unplug
the Oskar® Mini from the power outlet.
Dishwasher Use
All plastic components deteriorate through
the prolonged use of a dishwasher for
cleaning.
All accessories and processor tools can be
washed in hot soapy water except for the
processor body. Clean the processor body by
wiping with a damp cloth.
If using the dishwasher place parts only on
the top rack of your dishwasher.
Warning: Care must be taken when handling
the metal blades as these items are extremely
sharp.
Note: Always unplug the Oskar® Mini before
cleaning.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Recipes
White bean dip
Makes: 1½ cups
Artichoke, green onion & ricotta dip
Makes: 2 cups
Preparation: 10 mins
Preparation: 10 mins
2 x 400g cans white beans, rinsed, drained
1 teaspoon finely grated lemon rind
2 tablespoons freshly squeezed lemon juice
2 tablespoons olive oil
340g marinated artichokes, drained, chopped
250g fresh ricotta
3 green onions, trimmed, chopped
1 tablespoon freshly squeezed lemon juice
1 tablespoon warm water
2 garlic cloves, crushed
Grilled asparagus, to serve
1 large garlic clove, crushed
Bagel chips, to serve
1.Using the processing bowl fitted with the
processing blade, place all ingredients
into the food processor. Process
mixture, scrapping down the side of bowl
occasionally, until smooth.
1.Using the processing bowl fitted with the
processing blade, place all ingredients
into the food processor. Process
mixture, scrapping down the side of bowl
occasionally, until smooth.
2.Transfer to a serving bowl. Taste and
season with salt. Serve with grilled
asparagus, if desired.
2.Transfer to a serving bowl. Taste and
season with salt. Serve with bagel chips.
Garlic feta dip
Makes: 1 cup
Preparation: 10 mins
200g reduced-fat creamy feta, crumbled
200g low-fat fresh ricotta
2 tablespoons olive oil
2 large garlic cloves, crushed
1.Using the processing bowl fitted with the
processing blade, place all ingredients
into the food processor. Process
mixture, scrapping down the side of bowl
occasionally, until smooth.
2.Transfer to a bowl. Taste and season with
salt. Serve as part of an antipasto platter.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Recipes continued
Pesto
Salsa Verde
Serves: 4
Makes: 2 cups
Preparation: 10 mins
Serves: 4
Preparation: 5 mins
1 cup flat leaf parsley
½ cup dill
125g fresh basil leaves
3 cloves garlic
½ cup mint leaves
2 teaspoons lemon juice
sea salt
2 cloves garlic
1 tablespoon small capers
1 tablespoon grated lemon rind
Sea salt and freshly ground black pepper
¾ cup extra virgin olive oil
freshly ground black pepper
1 cup extra virgin olive oil
½ pine nuts, roasted
60g pecorino or parmesan, grated
1.Using the processing bowl fitted with the
processing blade, place all ingredients
into the food processor. Process
mixture, scrapping down the side of bowl
occasionally, until a chunky texture is
achieved.
1.Using the processing bowl fitted with
the processing blade, place the basil,
garlic, juice, salt, pepper and oil into the
food processor. Pulse mixture until just
combined.
Serving suggestion: Serve with grilled or
barbecued fish fillets or chicken breast
fillets.
2.Push down any ingredients that may have
come up the sides of the bowl and add the
nuts and cheese. Pulse mixture again until
a desired texture is achieved.
To serve: Boil a large pot of boiling water
with a little oil in it. Boil 500g pasta until
just tender. Drain pasta well but do not
rinse. Place hot pasta back in to pot and stir
through half of the pesto sauce. Add more
pesto to taste if desired. Serve with extra
cheese and a sprinkle of toasted pine nuts.
Store remaining pesto in an airtight jar in the
refrigerator with a little extra oil on top to
prevent browning. Discard after 5 days.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Recipes continued
Whole Egg Mayonnaise
Makes: about 3 cups
Zucchini tossed in Angel Hair Pasta
Serves: 4
Preparation: 2 mins
Preparation: 20 mins (+ marinating)
Cooking: 10 mins
2 eggs
2 small green zucchini
2 tablespoons lemon juice
1 tablespoon Dijon mustard
pinch sea salt
2 small yellow zucchini
3 cloves garlic, crushed
½ cup (125ml) extra virgin olive oil
500g angel hair pasta
2 cups vegetable or light olive oil
1.Using the processing bowl fitted with
the processing blade, place eggs, juice,
mustard and salt in the food processor.
Process until combined.
1 large onion, chopped
1 ½ tablespoons chopped fresh thyme
¼ cup (60ml) freshly squeezed lemon juice
sea salt and freshly ground black pepper
shaved parmesan, to serve
2.With the motor still running remove the
food pusher and start to pour in the oil
in a slow, thin stream until the mixture is
creamy and all the oil has been added.
1.Using the processing bowl fitted with
slicing blade; slice the zucchini, in
batches, to about a 4mm thickness.
3.Store in the refrigerator in an airtight
container for 2 weeks.
2.Place the zucchini slices into a bowl with
the crushed garlic and a little of the olive
oil; stir through and leave for 30 minutes.
3.Remove the slicing blade and insert the
processing blade; add onions and roughly
chop.
4.Meanwhile have a large pot of salted
boiling water ready for the pasta. It is best
to cook the pasta so that it is ready when
the zucchini is just cooked. Cook the
pasta until just tender.
5.Heat remaining oil in a large deep sided
frying pan and cook onions until they are
translucent. Add the zucchini rounds and
thyme and cook, stirring, until the zucchini
just starts to soften. Add the hot drained
pasta, lemon juice and salt and pepper to
taste. Stir through to combine.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Recipes continued
Feta and spinach triangles
Makes: 4
Quiche Lorraine
Serves: 6-8
Preparation: 25 mins
Cooking: 15 mins
Preparation: 20 mins
Cooking: 50 mins
1 tablespoon olive oil
1/3 cup packaged breadcrumbs
185g tasty cheese
1 medium brown onion, chopped finely
1 teaspoon paprika
6 bacon rashers, rind removed, roughly
chopped
¼ teaspoon chilli powder
100g baby spinach leaves
200g feta, crumbled
1 small onion, chopped finely
4 eggs
1 cup milk
4 sheets filo pastry
½ cup cream
30g butter, melted
½ cup self raising flour
pepper to taste
1.Preheat oven to 200ºC. Grease and line
two oven trays.
1.Take the spindle and insert the shredding
disc with the course shredder facing up.
2.Heat oil in medium frying pan. Cook
onion and spices, stirring until onion has
softened. Add spinach and cook, stirring,
about 3 minutes or until just wilted.
2.Using the processing bowl fitted with the
shredding disc, position the cheese in the
feed tube. Using the food pusher, grate
the cheese.
3.Using the processing bowl fitted with the
processing blade, process spinach in food
processor about 1 minute or until leaves
are chopped finely. Combine in medium
bowl with feta.
3.Preheat oven to 180°c. Lightly spray a
quiche dish with vegetable oil spray. Coat
the inside of the dish with the bread
crumbs.
4.Lay one sheet of the pastry on board.
Brush with some of the butter and top with
another sheet of the pastry. Repeat with
remaining butter and pastry.
4.Cook bacon in a frying pan until tender,
remove from pan and drain on absorbent
paper; cool.
5.In a large bowl combine the bacon, cheese
and onion.
5.Cut filo into four rectangles; top each
rectangle with spinach mixture. Brush
edges of pastry with butter; roll to enclose
filling. Brush each parcel with remaining
butter. Place on prepared oven tray. Bake,
about 10 minutes or until browned lightly.
6.Using the processing bowl fitted with the
processing blade; combine the remaining
ingredients in the food processor. Process
for 20 seconds.
7.Place the bacon mixture into the prepared
quiche dish and pour the egg mixture over
the top.
8.Bake in oven for about 50 minutes or until
cooked. Stand for 10 minutes before
cutting.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Recipes continued
Date and craisin balls
Makes: approx 16
Pistachio and fig pinwheels
Makes: approximately 24
Preparation: 15 mins
Preparation: 5 mins
Cooking: 25 mins
1 cup toasted muesli
1 cup rolled oats
30g butter
2 tablespoons maple syrup
1 teaspoon finely grated orange rind
200g dried figs, chopped
1 cup toasted pistachio
2 sheets ready rolled puff pastry
1 egg, beaten lightly
1/2 cup dried pitted dates, chopped
½ cup craisin
¼ cup honey
60g butter, melted
¾ cup desiccated coconut
1.Using the processing bowl fitted with the
processing blade, place muesli, dates,
honey and butter into the food processor.
Process about 45 seconds or until
combined.
1.Preheat oven 180ºC. Grease two baking
trays.
2.Melt butter in medium saucepan, add
syrup, rind and figs. Bring to a boil, reduce
heat, simmer, uncovered about 5 minutes.
Allow to cool to room temperature.
Note: Do not process for longer than 1½
minutes.
2.Place coconut into a shallow dish. Using
level tablespoons muesli mixture per ball,
roll mixture into small balls. Toss muesli
balls, 1 at a time, in coconut to coat.
Place in an airtight container. Cover and
refrigerate until required.
3.Meanwhile, using the processing bowl
fitted with the processing blade, process
pistachio in the food processor, about 1
minute or until chopped finely, transfer
to a medium bowl. Place fig mixture in
processor bowl. Process about 1 minute or
until pureed. Add fig to pistachio and stir
to combine.
4.Lay one sheet of the pastry on board. Top
with half of the pistachio and fig mixture
and roll to enclose. Cut into 1cm slices.
Place on prepared tray. Brush with egg
wash. Bake, about 15 minutes or until
browned lightly. Serve sprinkled with icing
sugar.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Recipes continued
Honey Pikelets
Baby Food
Preparation: 5 mins (+ 30 mins chilling)
Tips for freezing baby food: Food can be
frozen in a clean ice cube tray in portions,
covered, and once frozen, transferred to a
resealable bag. Portions can then be thawed
as you need it.
Cooking: 10 mins
3 large eggs
¼ cup honey
1 cup milk
1 ½ cups self raising flour
pinch salt
Potato and Pumpkin
250g potatoes
1.Using the processing bowl fitted with the
processing blade, add all ingredients
into the processor bowl and pulse until
combined. Scrape down sides of processor
and pulse again until smooth.
320g pumpkin
1.Peel potato and chop into small pieces.
Peel pumpkin and remove seeds. Cut into
pieces a little larger than the potato (the
potatoes take longer to cook).
2.Pour mixture into a jug and refrigerate for
30 minutes.
3.Place tablespoon amounts of mixture into
a lightly greased frying pan until golden on
each side.
2.Boil vegetables until tender but do not
overcook; strain and reserve some of the
liquid. Allow to cool to room temperature.
4.Serve with butter.
3.Using the processing bowl fitted with
the processing blade, place half of the
vegetables into the food processor with 1
tablespoon of the reserved liquid. Process
mixture, scrapping down the side of bowl
occasionally, until the desired texture
is achieved. Repeat with remaining
vegetables and 1 tablespoon of the
reserved liquid.
4.Warm before serving.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Recipes continued
Potato, Cauliflower, Broccoli and Cheese
1 small potato
Pumpkin, Zucchini and Sweet Potato
330g pumpkin
140g cauliflower
1 medium (170g) zucchini
125g sweet potato
95g broccoli
10g grated cheese
1.Peel pumpkin and sweet potato and cut
into chunks. Peel the zucchini and cut
into rounds.
1.Peel potato and chop into chunks. Cut the
cauliflower and broccoli into pieces.
2.Boil the pumpkin and sweet potato first
until almost soft; then add the zucchini
and cook until tender but do not overcook;
strain and reserve some of the liquid.
Allow to cool to room temperature.
2.Boil the potato first until almost soft; then
add the other vegetables and cook until
tender but do not overcook; strain and
reserve some of the liquid. Allow to cool to
room temperature.
3.Using the processing bowl fitted with
the processing blade, place half of the
vegetables into the food processor with 1
tablespoon of the reserved liquid. Process
mixture, scrapping down the side of bowl
occasionally, until the desired texture
is achieved. Repeat with remaining
vegetables and 1 tablespoon of the
reserved liquid.
3.Using the processing bowl fitted with
the processing blade, place half of the
vegetables into the food processor with 1
tablespoon of the reserved liquid. Process
mixture, scrapping down the side of bowl
occasionally, until the desired texture
is achieved. Repeat with remaining
vegetables and 1 tablespoon of the
reserved liquid.
4.Warm before serving.
4.Remove vegetables from processor and stir
through cheese.
5.Warm before serving.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Recipes continued
Apple and Pear
Pear, Banana and Papaya
1 large brown pear
1 small banana
1 medium green apple
2 large brown pears
¼ papaya
1.Peel fruit and chop into chunks.
1.Peel pear and chop into chunks.
2.Boil fruit until tender but do not overcook;
strain and reserve some of the liquid. Allow
to cool to room temperature.
2.Boil pear until tender; strain and reserve
some of the liquid. Allow to cool for to
room temperature.
3.Using the processing bowl fitted with
the processing blade, place half of the
fruit into the food processor with 1
tablespoon of the reserved liquid. Process
mixture, scrapping down the side of bowl
occasionally, until the desired texture is
achieved. Repeat with remaining fruit and
1 tablespoon of the reserved liquid.
3.Peel banana; chop into chunks. Peel
papaya and remove seeds; chop into
chunks.
4.Using the processing bowl fitted with
the processing blade, place half of the
fruit into the food processor with 1
tablespoon of the reserved liquid. Process
mixture, scrapping down the side of bowl
occasionally, until the desired texture is
achieved. Repeat with remaining fruit and
1 tablespoon of the reserved liquid.
4.Serve warm or cold.
5.Serve warm or cold.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
Download from Www.Somanuals.com. All Manuals Search And Download.
12 Month Replacement Guarantee
In the unlikely event that this appliance develops any malfunction
within 12 months of purchase (3 months commercial use) due to
faulty materials or manufacture, we will replace it for you
free of charge.
Should you experience any difficulties with
your appliance, please phone our customer
service line for advice on 1300 881 861 in
Australia, or 0800 786 232 in New Zealand.
Alternatively, you can send a written claim
to Sunbeam at the address listed below.
On receipt of your claim, Sunbeam will
seek to resolve your difficulties or, if the
appliance is defective, advise you on how
to obtain a replacement or refund.
In Australia you are entitled to a
replacement or refund for a major failure and
for compensation for any other reasonably
foreseeable loss or damage. You are also
entitled to have the goods repaired or
replaced if the goods fail to be of acceptable
quality and the failure does not amount to
a major failure.
Should your appliance require repair or
service after the guarantee period, contact
your nearest Sunbeam service centre.
Your Sunbeam 12 Month Replacement
Guarantee naturally does not cover misuse
or negligent handling and normal wear and
tear.
For a complete list of Sunbeam’s authorised
service centres visit our website or call:
Australia
Similarly your 12 Month Replacement
Guarantee does not cover freight or any other
costs incurred in making a claim. Please
retain your receipt as proof of purchase.
1300 881 861
Units 5 & 6, 13 Lord Street
Botany NSW 2019 Australia
The benefits given to you by this guarantee
are in addition to your other rights and
remedies under any laws which relate to the
appliance.
New Zealand
0800 786 232
26 Vestey Drive, Mt Wellington
Auckland, New Zealand
Our goods come with guarantees that cannot
be excluded under the Australian Consumer
Law and under the New Zealand Consumer
Guarantees Act.
Download from Www.Somanuals.com. All Manuals Search And Download.
Need help with your appliance?
Contact our customer service team or visit
our website for information and tips on
getting the most from your appliance.
In Australia
Or call 1300 881 861
In New Zealand
Or call 0800 786 232
is a registered trademark.
‘Oskar Mini’ is a trademark of Sunbeam Corporation.
Made in China.
Due to minor changes in design or otherwise,
the product may differ from the one shown in this leaflet.
© Copyright. Sunbeam Corporation Limited 2011.
ABN 45 000 006 771
Units 5 & 6, 13 Lord Street
Botany NSW 2019 Australia
Unit 3, Building D
26 Vestey Drive
Mt Wellington Auckland
New Zealand
Sunbeam Corporation is a division of GUD Holdings Ltd.
8/11
Download from Www.Somanuals.com. All Manuals Search And Download.
|