OPERATION AND PARTS MANUAL
MODEL T-20H
TRASH PUMP
Revision #0 (05/29/03)
STOWCONSTRUCTIONEQUIPMENT
A DIVISION OF MULTIQUIP INC.
POST OFFICE BOX 6254
PARTS DEPARTMENT:
800-427-1244
FAX: 800-672-7877
SERVICE DEPARTMENT/TECHNICAL ASSISTANCE:
800-478-1244
CARSON, CA 90749
310-537-3700 • 888-252-STOW [888-252-7869]
FAX:310-537-1986 • FAX:800-556-1986
E-MAIL: [email protected] • WWW: stowmfg.com
FAX:310-631-5032
Download from Www.Somanuals.com. All Manuals Search And Download.
HERE'S HOW TO GET
HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
PARTS DEPARTMENT
800-427-1244 or 310-537-3700
FAX: 800-672-7877 or 310-637-3284
SERVICE DEPARTMENT
800-421-1244
FAX: 310- 537-4259
TECHNICAL ASSISTANCE
800-478-1244
FAX: 310- 631-5032
WARRANTY DEPARTMENT
888-661-4279, or 310-661-4279
FAX: 310- 537-1173
STOW T-20H TRASH PUMP — PARTS MANUAL— REV. #0 (05/29/03) — PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
STOWT-20H — TABLE OF CONTENTS
HondaGX160K1TX2 Engine
Air Cleaner (Dual) Assembly.............................. 34-35
Camshaft Assembly ........................................... 36-37
Carburetor Assembly ......................................... 38-39
Control Assembly ............................................... 40-41
Crankcase Cover Assembly............................... 42-43
Crankshaft Assembly ......................................... 44-45
Cylinder Barrel Assembly................................... 46-47
Cylinder Head Assembly.................................... 48-49
Fan Cover Assembly .......................................... 50-51
Flywheel Assembly ............................................ 52-53
Fuel Tank Assembly ........................................... 54-55
Ignition Coil Assembly ........................................ 56-57
Muffler Assembly ............................................... 58-59
Piston Assembly................................................. 60-61
Recoil Starter Assembly..................................... 62-63
Gasket Kit Assembly ............................................... 65
Labels ................................................................ 66-67
STOW T-20H Gasoline
Powered Trash Pump
Here’s How To Get Help ............................................ 2
Table of Contents ...................................................... 3
Parts Ordering Procedures .................................... 4-5
Safety Message Alert Symbols .............................. 6-7
Rules For Safe Operation ...................................... 8-9
Pump Specifications/Dimensions .............................10
Engine Specifications ...............................................11
General Information .................................................12
Pump Components ..................................................13
Basic Engine ............................................................14
Pre-Inspection (Engine) ...........................................15
Pre-Set-up (Pump)...................................................16
Initial Start-up (Engine) ...................................... 17-18
Maintenance (Pump) ......................................... 20-21
Maintenance (Engine)........................................ 22-23
Preparation for Long-Term Storage.........................24
Troubleshooting (Pump)...........................................26
Troubleshooting (Pump/Engine) ..............................27
Explanation Of Code In Remarks Column ...............28
Suggested Spare Parts ............................................29
Pump Assy. ........................................................ 30-33
Terms and Condition Of Sale
—
Parts .................... 68
Specification and part number
are subject to change without
notice.
PAGE 4 —STOW T-20H TRASH PUMP — PARTS MANUAL — REV. #0 (05/29/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS ORDERING PROCEDURES
When ordering parts,
please supply the following information:
❒
Dealeraccountnumber
❒
❒
❒
❒
❒
❒
Dealernameandaddress
Shipping address (if different than billing address)
Returnfaxnumber
Applicable model number
Quantity,part number and description of each part
Specifypreferredmethodofshipment:
Note:Unlessotherwiseindicatedbycustomer, all
orders are treated as “Standard Orders”, and will
ship within 24 hours.We will make every effort to
ship “Air Shipments” the same day that the order is
received, if prior to 2PM west coast time. “Stock
Orders” must be so noted on fax or web forms.
✓
✓
✓
✓
✓
✓
FedEx or UPS Ground
FedEx or UPS Second Day or Third Day
FedEx or UPS Next Day
Federal Express Priority One
DHL
Truck
Place Your Parts Order Via Web or Fax
For Even More Savings!
Here’s how to get help...
Please have the model and serial number on
hand when calling.
Parts Department
Extra Discounts!
800-427-1244
310-537-3700
Fax:800-672-7877
Fax:310-637-3284
All parts orders which include complete part numbers
and are received by our automated web parts order
system, or by fax qualify for the following extra
discounts:
Mayco Parts
800-306-2926
310-537-3700
Fax:800-672-7877
Fax:310-637-3284
Ordered
via
Standard
orders
Stock orders
($750 list and above)
Service Department
800-478-1244
310-537-3700
Fax
3%
5%
10%
10%
Fax:310-537-4259
Web
MQ Power Service Department
Special freight allowances
when you order 10 or more
line items via Web or Fax!**
FedEx Ground Service at no charge for freight
800-835-2551
310-537-3700
Fax:310-638-8046
Warranty Department
800-421-1244, Ext. 279
310-537-3700, Ext. 279
Fax:310-537-1173
No other allowances on freight shipped by any other
carrier.
Multiquip’s Main Phone Numbers
800-421-1244
310-537-3700
Fax:310-537-3927
NOTE:DISCOUNTSARESUBJECTTOCHANGE
MULTIQUIP INC.
Direct TOLL-FREE access
to our Parts Department:
Toll-free nationwide — 800-427-1244
18910WILMINGTON AVENUE
POST OFFICE BOX 6254
CARSON, CALIFORNIA 90749
310-537-3700 • 800-421-1244
FAX:310-537-3927
WWW:multiquip.com
STOW T-20H TRASH PUMP — PARTS MANUAL— REV. #0 (05/29/03) — PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
STOWT-20H — SAFETY MESSAGE ALERT SYMBOLS
FORYOUR SAFETY ANDTHE SAFETY OF OTHERS!
HAZARD SYMBOLS
Safety precautions should be followed at all times when operating
this equipment. Failure to read and understand the Safety
Messages and Operating Instructions could result in injury to
yourself and others.
Lethal Exhaust Gases
Engine exhaust gases contain poisonous
This Owner's Manual has been
developed to provide complete
instructions for the safe and efficient
operation of the STOW ModelT-20H
carbon monoxide. This gas is colorless and
odorless, and can cause death if inhaled.
NEVER operate this equipment in a confined
area or enclosed structure that does not
provide ample free flow air.
Trash Pump. Refer to the engine
manufacturers instructions for data
relative to its safe operation.
Before using these pumps,
ensure that the operating
individual has read and
understands all instructions in
this manual.
Explosive Fuel
GASOLINE is extremely flammable, and its
vapors can cause an explosion if ignited. DO
NOT start the engine near spilled fuel or
combustible fluids. DO NOT fill the fuel tank
while the engine is running or hot. DO NOT
overfill tank, since spilled fuel could ignite if it
comes into contact with hot engine parts or
sparks from the ignition system. Store fuel in
approved containers, in well-ventilated areas
and away from sparks and flames. NEVER
SAFETY MESSAGE ALERT SYMBOLS
The three (3) Safety Messages shown below will inform you
about potential hazards that could injure you or others. The
Safety Messages specifically address the level of exposure to
the operator, and are preceded by one of three words: DANGER,
WARNING, or CAUTION.
Burn Hazards
DANGER: You WILL be KILLED or
SERIOUSLY injured if you do not follow
Engine components can generate extreme heat.
To prevent burns, DO NOT touch these areas
while the engine is running or immediately after
operations. Never operate the engine with heat
shields or heat guards removed.
WARNING: You CAN be KILLED or
SERIOUSLY injured if you do not follow
directions.
Rotating Parts
CAUTION: You CAN be injured if you
do not follow directions.
NEVER operate equipment with covers, or
guards removed. Keep fingers, hands, hair and
clothing away from all moving parts to prevent
injury.
Potential hazards associated with the STOW T-20H Trash Pump
operation will be referenced with Hazard Symbols which appear
throughout this manual, and will be referenced in conjunction
with Safety Message Alert Symbols.
PAGE 6 —STOW T-20H TRASH PUMP — PARTS MANUAL — REV. #0 (05/29/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOWT-20H — SAFETY MESSAGE ALERT SYMBOLS
Accidental Starting
Respiratory Hazard
ALWAYS place the engine ON/OFF switch in
the OFF position when the pump is not in use.
ALWAYS wear approved respiratory
protection.
Equipment Damage Messages
Sight and Hearing hazard
Other important messages are provided throughout this manual
to help prevent damage to your pump, other property, or the
surrounding environment.
ALWAYS wear approved eye and hearing
protection.
This pump, other property, or the
surrounding environment could be
damaged if you do not follow
instructions.
STOW T-20H TRASH PUMP — PARTS MANUAL— REV. #0 (05/29/03) — PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES FOR SAFE OPERATION
■
NEVER touch the hot exhaust manifold,
muffler or cylinder.Allow these parts to
cool before servicing engine or pump.
DANGER:
Failure to follow instructions in this manual may
lead to serious injury or even death! This
equipment is to be operated by trained and
qualified personnel only!This equipment is for
industrial use only.
The following safety guidelines should always be used when
operating the trash pump:
■
■
HighTemperatures – Allow the engine to cool before adding
fuel or performing service and maintenance functions. Contact
with hot! components can cause serious burns.
GENERAL SAFETY
■
DO NOT operate or service this equipment before
readingthisentiremanual.
The engine of this pump requires an adequate free flow of
cooling air. NEVER! operate the pump in any enclosed or
narrow area where free flow of the air is restricted. If the air
flow is restricted it will
■
■
This equipment should not be operated by
persons under 18 years of age.
NEVER operate this equipment without proper
protective clothing, shatterproof glasses, steel-
toed boots and other protective devices required
by the job.
cause serious damage
to the pump or engine
and may cause injury to
people and property.
Remember the pump's
engine
gives
off
DEADLY gases.
■
■
NEVER operate this equipment when not feeling
well due to fatigue, illness or taking medicine.
■
■
ALWAYS refuel in a well-ventilated area, away from sparks
NEVER operate this equipment under the
influence or drugs or alcohol.
and open flames.
ALWAYS use extreme caution when working with flammable
liquids. When refueling, stop the engine and allow it to cool.
DO NOT smoke around or near the machine. Fire or explosion
could result from fuel vapors, or if fuel is spilled on a hot
engine.
■
■
■
Whenever necessary, replace nameplate, operation and safety
decals when they become difficult read.
■
NEVER operate the pump in an explosive
atmosphere or near combustible
materials. An explosion or fire could result
causing severe bodily harm or even
death.
ALWAYS check the machine for loosened threads or bolts
before starting.
ALWAYS wear proper respiratory (mask) hearing and eye
protection equipment when operating the pump.
■
■
Topping-off to filler port is dangerous, as it tends to spill fuel.
Refer to the Engine Owner's Manual for engine technical
questions or information.
■
■
NEVER use accessories or attachments, which are not
recommended by Multiquip for this equipment. Damage to
the equipment and/or injury to user may result.
Manufacturer does not assume responsibility for any accident
due to equipment modifications.
PAGE 8 —STOW T-20H TRASH PUMP — PARTS MANUAL — REV. #0 (05/29/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES FOR SAFE OPERATION
■
■
■
■
NEVER Run engine without air cleaner. Severe engine
■
■
High Temperatures – Always stop engine and allow the
engine to cool before adding fuel, oil or performing service
and maintenance functions. Contact with hot components can
cause serious burns.
damage may occur.
ALWAYS read, understand, and follow procedures in
Operator’s Manual before attempting to operate equipment.
NEVER disconnect any "emergency or safety devices".
These devices are intended for operator safety. Disconnection
of these devices can cause severe injury, bodily harm or even
death! Disconnection of any of these devices will void all
warranties.
ALWAYS be sure the operator is familiar with proper safety
precautions and operation techniques before using pump.
ALWAYS store equipment properly when it is not being used.
Equipment should be stored in a clean, dry location out of the
reach of children.
Maintenance Safety
■
■
■
■
NEVER leave the pump unattended, turn off engine when
unattended.
NEVER lubricate components or attempt service on a running
machine.
Unauthorized equipment modifications will void all
warranties.
■
ALWAYS allow the machine a proper amount of time to cool
before servicing.
NEVER pump volatile, explosive, flammable or low flash point
fluids.These fluids could ignite or explode.
■
■
Keep the machinery in proper running condition.
Fix damage to the machine immediately and always replace
broken parts, or missing decals.
■
■
NEVER operate the pump in an explosive atmosphere.
Before starting the pump, check that the clean-out cover is
securely fasten.
■
■
■
Dispose of hazardous waste properly.Examples of potentially
hazardous waste are used motor oil, fuel and fuel filters.
■
■
ALWAYS ensure pump is on level ground before use.
DO NOT use food or plastic containers to dispose of
hazardous waste.
Become familiar with the components of the pump before
operating.
DO NOT pour waste, oil or fuel directly onto the ground,
down a drain or into any water source.
■
■
ALWAYS replace any worn or damaged warning decals.
NEVER pump corrosive chemicals or water containing toxic
substances. These fluids could create serious health and
environmental hazards. Contact local authorities for
assistance.
Emergencies
■
ALWAYS know the location of the
nearest fire extinguisher.
■
NEVER open the priming plug when pump is hot. Hot water
inside could be pressurized much like the radiator of an
automobile. Allow pump to cool to the touch before loosening
plug.
■
■
ALWAYS know the location of the nearest
first aid kit.
■
■
NEVER open the pump housing during operation or start the
pump with the clean-out cover removed.The rotating impeller
inside the pump can cut or sever objects caught in it.
In emergencies always know the location of the
nearest phone or keep a phone on the job site.
Also know the phone numbers of the nearest
ambulance, doctor and fire department. This
information will be invaluable in the case of an
emergency.
NEVER block or restrict flow from discharge hose. Remove
kinks from discharge line before starting pump. Operation
with a blocked discharge line can cause water inside pump
to overheat.
■
■
ALWAYS fill the pump casing with water before starting the
engine. Failure to maintain water inside the pump housing
will cause severe damage to the pump.
In winter drain water from pump housing to prevent freezing.
STOW T-20H TRASH PUMP — PARTS MANUAL— REV. #0 (05/29/03) — PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
STOWT-20H — SPECIFICATIONS/DIMENSIONS (PUMP)
Table 1. Specifications (Pump)
Model
T-20H
Type
Trash Pump
Suction & Discharge Size
2.00 in. (51 mm.)
Maximum Pumping
Capacity
158 gallons/minute
(598 liters/minute)
Pump
Max. Solids Diameter
Max. Lift
1.00 in. (25 mm.)
25 ft. (7.62 meters)
79 ft. (24 meters)
Max. Head
26.0 x 18.0 X 22.0 in.
(66 X 45 X 56 cm.)
Dimension
(L x W x H)
115 lbs. (52 Kg.)
Dry Net Weight
Figure 1. T-20H Dimensions
PAGE 10 —STOW T-20H TRASH PUMP — PARTS MANUAL — REV. #0 (05/29/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOWT-20H — SPECIFICATIONS/DIMENSIONS (ENGINE)
Table 2. Specifications (Engine)
Model
HONDA GX160K1TX2
Air-cooled 4 stroke, Single
Cylinder, OHV, Horizontal
Shaft Gasoline Engine
Type
2.7 in. x 1.8 in.
(68 mm x 45 mm)
Bore X Stroke
Displacement
Max Output
163 cc (9.9 cu-in)
5.5 H.P./3600 R.P.M.
Engine
Approx. 0.95 U.S. gallons
(3.6 liters)
Fuel Tank Capacity
Unleaded Automobile
Gasoline
Fuel
Lube Oil Capacity
.60 liters (0.63 qts)
Centrifugal Fly-weight Type
Recoil Start
Speed Control
Method
Starting Method
12.0 x 14.4 x 13.2 in.
(304 x 362 x 335 mm)
Dimension
(L x W x H)
Dry
Net Weight
33.1 lbs (15 Kg.)
STOW T-20H TRASH PUMP — PARTS MANUAL— REV. #0 (05/29/03) — PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
STOWT-20H — GENERAL INFORMATION
Elevation
APPLICATION
Higher elevations will effect the performance of the pump. Due to
less atmospheric pressure at higher altitudes, pumps DO NOT
have the priming ability that they have at sea level. This is due to
the “thinner air” or lack of oxygen at higher altitudes.
The STOW Model T-20H Trash Pump is designed to be used
for de-watering applications. Both the suction and discharge
ports on theT-20H pump use a 2-inch diameter opening, which
allows the pump to pump at a rate of approximately 158 gallons/
minute (gpm) or 598 liters/minute (lpm).
A general rule of thumb is that for every 1,000 feet of elevation
above sea level a pump will lose one foot of priming ability.
Trash or self priming pumps are designed to purge air from the
suction line and create a partial vacuum in the pump body.The
reduced atmospheric pressure inside the pump allows water to
flow through the suction line and into the pump body. The
centrifugal force created by the rotating impeller pressurizes the
water and expels it from the pump.
For example, in Flagstaff, Arizona where the elevation is
approximately 7,000 feet, the pump would have a suction lift of
only 18 feet rather than the 25 feet at sea level. Table 3 shows
suction lift at various elevations.
Power Plant
Table 3. Suction Lift at Various Elevations
This trash pump is powered by an 5.5 horsepower air cooled 4-
stroke, single cylinder HONDA GX-160 gasoline engine that
incorporates a low "Oil Alert Feature"
Altitude
Suction Lift in Feet (Meters)
Feet (Meters)
Sea Level
10.0 (3.048) 15.0 (4.572) 20.0 (6.096) 25.0 (7.620)
8.80 (2.680) 13.2 (4.023) 17.6 (5.364) 22.0 (6.705)
7.80 (2.377) 11.7 (3.566) 15.6 (4.754) 19.5 (5.943)
6.90 (2.103) 10.4 (3.169) 13.8 (4.206) 17.3 (5.273)
6.20 (1.889) 9.30 (2.834) 12.4 (3.779) 15.5 (4.724)
Oil Alert Feature
2,000 (610)
4,000 (1,219)
6,000 (1,829)
8,000 (2,438)
In the event of low oil or no oil, the HONDA GX-160 engine has
a built-in oil alarm engine shut-down feature. In the event the oil
level is low the engine will automatically shut-down.
Trash Pump
10,000 (3,048) 5.70 (1.737) 8.60 (2.621) 11.4 (3.474) 14.3 (4.358)
Trash pumps derive their name from their ability to handle a
greater amount of debris and solids than standard centrifugal
pumps.These pumps generally handle solids up to 1/2 the size
of the discharge opening making them less likely to clog. Also
trash pumps are capable of handling water with 25% solids by
weight.
Table 4 shows percentage drops in performance as elevation
increases.
Table 4. Performance Loss at Various
Elevations
The advantage of using a trash pump is that it can be quickly and
easily disassembled in the field "without tools" and easily
cleaned when clogged.
Altitude
Discharge Flow
Discharge Head
Suction Lift
Feet (Meters
This pump is intended to be used for dewatering applications
and is capable of suction lifts up to 25 feet at sea level. For
optimal suction lift performance keep the suction hose or line as
short as possible. In general always place the pump as close to
the water as possible.
Sea Level
100%
97%
95%
93%
91%
88%
100%
95%
91%
87%
83%
78%
2,000 (610)
4,000 (1,219)
6,000 (1,829)
8,000 (2,438)
10,000 (3,048)
Pump Support
The pump should always be placed on solid stationary ground
in a level position.
NEVER place the pump on soft soil. The suction hose or pipe
connection should always be checked for tightness and leaks. A
small suction leak in the hose or fittings could prevent the pump
from priming.
PAGE 12 —STOW T-20H TRASH PUMP — PARTS MANUAL — REV. #0 (05/29/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOWT-20H — PUMP COMPONENTS
Figure 2 shows a typical application using the STOW T-20H trash pump. Please note that this pump is intended for the removal of
clean water and water containing some debris and solids. Maximum size of solids should not exceed 1 inch (25 mm) in diameter. DO
NOT set strainer on bottom of water bed. Placing the strainer above the water bed will prevent the pump from drawing in excessive
amounts of sand and foreign debris.
Figure 2. STOWT-20H Pump Applic
1. Pump – The STOW Model T-20H is 2-inch trash pump 6. Suction Port – Connect a 2-inch inlet hose to this port.
used in general de-watering applications. Typical
dewatering applications consist of manholes, septic tanks,
fast and slow seepage ditch water, silt water, mud water
and muck water.
Use two worm clamps to secure the hose.
7. Suction Hose – Connect this flexible rubber hose to the
suction port on the pump. Make sure that the hose lays flat
and is not kinked. Use only recommended type suction
hose. Contact Multiquip parts department for ordering
information
2. Fill Cap – Prior to operation, the pump casing should be
filled with water.Remove this cap to add water to the pump.
After the initial prime, a sufficient amount of water will be
retained in the casing so that the operator will not need to
re-prime later.
8. Clean-out Cover Handles –To gain access to the pump's
clean-out area, grip both handles, then pull to remove cover.
Make sure both locking knobs have been released before
attempting to remove clean-out cover.
If the casing is dry or has insufficient water, the pump will
have difficulty in priming which could lead to premature
mechanical seal wear thus causing damage to the pump.
9. Drain Plug – Remove this plug to drain water from the
pump.
3. Discharge Port – Connect a 2-inch discharge hose to this
10. Clean-out Cover – Remove cover to gain access to the
port.
clean-out area.
4. Worm Clamp – Used to secure the hose to the inlet and
outlet ports on the pump. Use two clamps to secure the
hose on the inlet side of the pump.
11. Locking Knobs– Turn both knobs clockwise to secure
clean-out cover, turn counter-clockwise to release cover.
12. Strainer – Always attach a strainer to bottom side of the
suction hose to prevent large objects and debris from
entering the pump. Strainer should be positioned so that it
will remain completely under water.Running the pump with
the strainer above water for long periods can damage pump.
5. Discharge Hose – Connect this flexible rubber hose to
the discharge port on the pump. Make sure that the hose
lays flat and is not kinked. Use only recommended type
discharge hose. Contact Multiquip parts department for
ordering information.
STOW T-20H TRASH PUMP — PARTS MANUAL— REV. #0 (05/29/03) — PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
STOWT-20H — BASIC ENGINE
Figure 3. Engine Controls and Components
INITIAL SERVICING
6. Choke Lever – Used in the starting of a cold engine, or in
cold weather conditions. The choke enriches the fuel
mixture.
The engine (Figure 3) must be checked for proper lubrication and
filled with fuel prior to operation. Refer to the manufacturers engine
manual for instructions & details of operation and servicing. The
engine shown above is a HONDA engine, operation for other
types of engines may vary somewhat.
7. Air Cleaner – Prevents dirt and other debris from entering
the fuel system. Remove wing-nut on top of air filter
cannister to gain access to filter element.
1. Fuel Filler Cap – Remove this cap to add unleaded
gasoline to the fuel tank. Make sure cap is tightened
securely. DO NOT over fill.
Operating the engine without an
air filter, with a damaged air filter,
or a filter in need of replacement
will allow dirt to enter the engine,
causing rapid engine wear.
DANGER
Adding fuel to the tank should be done only when
the engine is stopped and has had an opportunity to
cool down. In the event of a fuel spill, DO NOT attempt to start the
engine until the fuel residue has been completely wiped up, and the
area surrounding the engine is dry.
8. Spark Plug – Provides spark to the ignition system. Set
spark plug gap to 0.6 - 0.7 mm (0.028 - 0.031 inch) Clean
spark plug once a week.
9. Muffler – Used to reduce noise and emissions.
2. Throttle Lever – Used to adjust engine RPM speed (lever
advanced forward SLOW, lever back toward operator
FAST).
WARNING
3. Engine ON/OFF Switch – ON position permits engine
Engine components can generate extreme heat.
To prevent burns, DO NOT touch these areas
starting, OFF position stops engine operations.
4. Recoil Starter (pull rope) – Manual-starting method. Pull
the starter grip until resistance is felt, then pull briskly and
smoothly.
while the engine is running or immediately after operating. NEVER
operate the engine with the muffler removed.
10. Fuel Tank – Holds unleaded gasoline. For additional
5. FuelValve Lever – OPEN to let fuel flow, CLOSE to stop
information refer to engine owner's manual.
the flow of fuel.
PAGE 14 —STOW T-20H TRASH PUMP — PARTS MANUAL — REV. #0 (05/29/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOWT-20H — PRE-INSPECTION (ENGINE)
3. Insertandremovethedipstickwithoutscrewingitintothefiller
neck. Check the oil level shown on the dipstick.
CAUTION
NEVER operate the pump
in a confined area or
enclosed area structure that
does not provide ample free
flow of air.
4. If the oil level is low (Figure 5), fill to the edge of the oil filler
holewiththerecommendedoiltype(Table5).Maximum oil
capacity is 1.16 quarts (1.1 liters)
ALWAYS wear approved eye and hearing
protection before operating the pump.
Before Starting
Figure 5. Engine Oil Dipstick (Oil Level)
Table 5. Oil Type
1.
Read safety instructions at the
beginning of manual.
2.
Clean the pump, removing dirt and
dust, particularly the engine
cooling air inlet, carburetor and air
cleaner.
Season
Summer
Spring/Fall
Winter
Temperature
25°C or Higher
25°C~10°C
Oil Type
SAE 10W-30
SAE 10W-30/20
SAE 10W-10
3.
4.
5.
Check the air filter for dirt and dust. If air filter is dirty, replace
air filter with a new one as required.
0°C or Lower
Check carburetor for external dirt and dust. Clean with dry
compressed air.
Check fastening nuts and bolts for tightness.
Explosive Fuel
DANGER
Engine Oil Check
1.
To check the engine oil level, place the pump on secure
level ground with the engine stopped.
Motor fuels are highly flammable and can be
dangerous if mishandled. DO NOT smoke
while refueling. DO NOT attempt to refuel the
pump if the engine is hot! or running.
2.
Remove the filler dipstick from the engine oil filler hole
(Figure 4) and wipe clean.
Fuel Check
1. Remove the gasoline cap located on top of fuel tank.
2. Visually inspect to see if the fuel level is low. If fuel is low,
replenish with unleaded fuel.
3. When refueling, be sure to use a strainer for filtration. DO
NOT top-off fuel. Wipe up any spilled fuel immediately!
Figure 4. Engine Oil Dipstick (Removal)
STOW T-20H TRASH PUMP — PARTS MANUAL— REV. #0 (05/29/03) — PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
STOWT-20H — PRE-SETUP (PUMP)
Before Starting
Suction and discharge hoses are
NOTE
1. Read safety instructions at the
beginning of manual.
available from Multiquip. Contact
your nearest dealer for more
information.
2. Place pump as near to water as
possible,onafirmflat,levelsurface.
5. The discharge hose is usually a collapsible (thin-walled)
hose, however if a thin-walled discharge hose is not avail-
able, a rigid suction hose can be substituted in its place.
3. Toprimepump,removefillcap(Figure2)andfillpumpcasing
with water.If the pump casing is not filled with water before
starting, it will not begin pumping.
6. Make sure the suction strainer (Figure 2) is clean and
securely attached to the water end of the suction hose. The
strainer is designed to protect the pump by preventing large
objects from being pulled into the pump.
CAUTION :
Pump casing must be filled with water
before using pump. Otherwise pump will
not be able to begin pumping.
CAUTION :
The strainer should be positioned so it will
remain completely under water. Running the
pump with the strainer above water for long
periods can damage the pump.
WARNING :
DO NOT open fill cap if pump is hot!Water
inside may be under pressure.
CAUTION :
DO NOT pump flammable fluids, corrosive
chemicals or fluids containing toxic substances.
These fluids can create potentially dangerous
health and environmental hazards. Contact
local authorities for assistance.
4. Checkforleaksbetweenpumpandengine.Ifwaterisleaking
between the pump and engine housing, the seal inside the
pumpmaybewornordamaged.Continued operationofthe
pumpisnot recommended.Furtherusageofthe pumpunder
theseconditionsmaycauseseverewaterdamagetoengine.
Hoses and Clamps
CAUTION :
This pump uses a water-cooled mechanical
1. Check that all hoses are securely attached to the pump.
Make certain suction hose (Figure 2) does not have any air
leakage.Tighten hose clamps and couplings as required.
seal to prevent water from seeping into the
engine. The passage of water through the
pump casing lubricates the seal and prevents
it from overheating. NEVER! operate the pump
without water in the casing as this will cause
damage to the mechanical seal.
2. Itisrecommendedthat 2 clampsbeusedwhensecuringthe
suction hose to the inlet side (suction) of the pump.
3. Remember suction hoses must be rigid enough not to
collapse when the pump is in operation.
4. Check that the discharge hose (Figure 2) is not restricted.
Place hose so that it lays as straight as it is possible on the
ground. Remove any twists or sharp bends from hose which
may block the flow of water.
PAGE 16 —STOW T-20H TRASH PUMP — PARTS MANUAL — REV. #0 (05/29/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOWT-20H — INITIAL START-UP (ENGINE)
3. Place the choke lever (Figure 8) in the "OPEN " position if
CAUTION :
starting a cold engine.
DO NOT attempt to operate the pump until the Safety, General
Information and Inspection sections of this manual have been
read and thoroughly understood.
This section is intended to assist the operator with the initial
start-up of the trash pump. It is extremely important that this
section be read carefully before attempting to use the pump in
the field.
Starting the Engine (HONDA engine)
Figure 8. Engine Choke Lever (Open)
1. Place the engine fuel valve lever (Figure 6) to the "ON"
position.
4. Placethechokelever(Figure 9)inthe"CLOSED"position
if starting a warm engine or the temperature is warm.
Figure 6. Engine FuelValve Lever (ON Position)
2. Move the throttle lever (Figure 7) away from the slow
position, about 1/3 of the way toward the fast position.
Figure 9. Engine Choke Lever (Closed)
5. Place the engine ON/OFF switch (Figure 10) in the "ON "
position.
Figure 7. Throttle Lever (1/3 Start Position)
Figure 10. Engine ON/OFF Switch (ON Position)
STOW T-20H TRASH PUMP — PARTS MANUAL— REV. #0 (05/29/03) — PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
STOWT-20H — INITIAL START-UP (ENGINE)
6. Grasp the starter grip (Figure 11) and slowly pull it out.The
CAUTION :
resistancebecomesthehardestatacertainposition,corre-
spondingtothecompressionpoint.Pullthestartergripbriskly
andsmoothlyforstarting.
ALWAYS run engine at full speed while
pumping.
Stopping The Engine
Normal Shutdown
1. Movethethrottlelever tothe IDLEposition (Figure14)and
run the engine for three minutes at low speed.
Figure 11. Starter Grip
7. If the engine has started, slowly return the choke lever
(Figure 12 ) to the CLOSED position. If the engine has not
started repeat steps 1 through 6.
Figure 14.Throttle Lever (Idle)
2. Aftertheenginecools,turntheengineON/OFFswitchtothe
“OFF” position (Figure 15).
Figure 12. Choke Lever (Closed)
8. Beforethepumpisplacedintooperation,runtheenginefor
severalminutes. Checkfor fuelleaks,andnoisesthatwould
associate with a lose component.
Figure 15. Engine ON/OFF Switch (OFF)
3. Place the fuel shut-off lever (Figure 16) in the OFF
9. To begin pumping, place the throttle lever (Figure 13) in the
position.
"RUN"position.
Figure 16. Fuel Valve Lever (OFF)
Emergency Showdown
1. MovethethrottleleverquicklytotheIDLE position,andplace
Figure 13. Throttle Lever (Run)
the engine ON/OFF switch in the OFF position.
PAGE 18 —STOW T-20H TRASH PUMP — PARTS MANUAL — REV. #0 (05/29/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
STOW T-20H TRASH PUMP — PARTS MANUAL— REV. #0 (05/29/03) — PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
STOWT-20H — MAINTENANCE (PUMP)
Pump Vacuum Test
Adjusting Impeller Clearance
1. If it is necessary to replace impeller or volute, be sure
clearance between impeller and volute is adjusted
CAUTION :
DO NOT attempt to start the engine unless
the pump has previously been primed with
correctly.
2. The impeller should be as close to the volute as possible
without rubbing against it. Clearance is adjusted by
adding or removing shims from behind the impeller.
water. Severe pump damage will occur if
pump has not been primed.
To perform the pump vacuum test do the following:
3. Check clearance between impeller and insert by slowly
pulling starter rope to turn impeller. Remove spark plug
to make it easier to turn impeller.
1. Remove the pump fill cap (Figure 2), and fill the pump
with water.
2. Start the engine as outlined in the initial start-up section,
and wait for the pump to begin pumping.
It is important not to remove too
many shims or the clearance
between the impeller and volute
will become too wide and pump
performance will be reduced.
Remember as the impeller wear
3. As shown in Figure 17 (next page), place a water hose
inside the discharge opening of the pump, and turn on
the water.This flow of water into the discharge opening
will prevent the pump from running dry.
down, additional shims may be required to maintain the
clearance between the impeller and insert.
4. Place the Pump Vacuum Tester (P/N 7000030) over
the pump suction (inlet) opening (Figure 17) with the
vacuum gauge facing upwards. It may be necessary to
apply a small amount of water around the rubber seal of
the vacuum tester to make a good suction fit.
4. Check the impeller every six months for wear, and for
clearance between the impeller face and the volute. Also
check the shaft seal for wear, as well as the shaft sleeve.
Pump Cleaning
5. Check and make sure that there are no air leaks between
the vacuum tester and the inlet port on the pump. If air
leaks are present reseat vacuum tester.
After pumping water containing large amounts of dirt and
debris, perform the following:
6. Run the pump for a few minutes while monitoring the
vacuum gauge. If the gauge indicates a reading between
-25 and -20 in. Hg. (inches of mercury) then it can be
assumed that the pump is working correctly.
1. Remove the drain plug from the pump housing (Figure 2)
and drain any water left in the pump.
2. Loosen the two locking hand knobs (turn counter-
clockwise) and remove clean-out cover.
25 in. Hg (inches of mercury)
translates into 25 feet of lift at sea
level.
3. Clean and remove dirt, debris from pump casing.Inspect
impeller and volute for wear. Replace any damaged or
worn parts.
7. If the vacuum tester gauge indicates a reading CAUTION :
below -20 in. Hg, it can then be assumed that the pump
is not functioning correctly, and corrective action needs
to be taken.
The impeller may develop sharp edges.
Use extreme care when cleaning around
the impeller to prevent being cut.
6. To test the flapper valve, shut down the engine. The
vacuum tester should remain attached to the pump
suction inlet port by vacuum. This indicates the pump's
flapper valve is seating properly to hold water in the
suction hose when the engine is stopped.This prevents
backflow and allows for faster priming when the engine
is restarted.
PAGE 20 —STOW T-20H TRASH PUMP — PARTS MANUAL — REV. #0 (05/29/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOWT-20H — MAINTENANCE (PUMP)
ing may vary
ude. See Tables 3
Figure 17. Pump VacuumTester
STOW T-20H TRASH PUMP — PARTS MANUAL— REV. #0 (05/29/03) — PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
STOWT-20H — MAINTENANCE (ENGINE)
Engine Maintenance
Perform engine maintenance procedures as referenced by
Table 6 below:
Table 6. Engine Maintenance Schedule
FIRST
EVERY
EVERY
EVERY
YEAR
OR
EVERY
2 YEARS
OR
MONTH 3 MONTHS 6 MONTHS
OR
DESCRIPTION (3)
OPERATION
BEFORE
OR
OR
10 HRS.
25 HRS.
50 HRS.
100 HRS.
200 HRS.
CHECK
CHANGE
CHECK
X
Engine Oil
X
X
X
Air Cleaner
All Nuts & Bolts
Spark Plug
CHANGE
X (1)
Re-tighten If
Necessary
CHECK-CLEAN
REPLACE
CHECK
X
X
X
Cooling Fins
Spark Arrester
Fuel Tank
CLEAN
X
X
CLEAN
Fuel Filter
CHECK
X
Idle Speed
CHECK-ADJUST
CHECK-ADJUST
CHECK
X (2)
Valve Clearance
Fuel lines
X (2)
Every 2 years (replace if necessary) (2)
(1) Service more frequently when used in DUSTY areas.
(2) These items should be serviced by your servic dealer, unless you have the proper tools and are mechanically
proficient. Refer to the HONDA shop Manual for service procedures
(3) For commercial use, log hours of operation to determine proper maintenance intervals.
Reference manufacturer engine
manual for specific servicing
instructions.
PAGE 22 —STOW T-20H TRASH PUMP — PARTS MANUAL — REV. #0 (05/29/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOWT-20H — MAINTENANCE (ENGINE)
DANGER :
Maintenance
Performtheenginemaintenanceproceduresasindicatedbelow:
DO NOT use gasoline as a cleaning solvent,
because that would create a risk of fire or
explosion.
DAILY
■
Thoroughly remove dirt and oil from the engine and control
area.Clean or replace the air cleaner elements as necessary.
Check and retighten all fasteners as necessary. Check the
spring box and bellows for oil leaks. Repair or replace as
needed.
ENGINEAIRCLEANER
1. Remove the air cleaner cover and foam filter element as
shown in Figure 20.
WEEKLY
■
Remove the fuel filter cap and clean the inside of the fuel
tank.
2. Tap the paper filter element (Figure 20) several times on a
hard surface to remove dirt, or blow compressed air [not
exceeding 30 psi (207 kPa, 2.1 kgf/cm2)] through the filter
elementfromtheaircleanercaseside.NEVER brushoffdirt.
Brushingwillforcedirtintothefibers.Replacethepaperfilter
element if it is excessively dirty.
■
■
Remove or clean the filter at the bottom of the tank.
Remove and clean the spark plug (Figure 18), then adjust
the spark gap to 0.028 ~0.031 inch (0.6~0.7 mm).This unit
has electronic ignition, which requires no adjustments.
3. Cleanfoamelementinwarm,soapywaterornonflammable
solvent. Rinseanddrythoroughly. Diptheelementinclean
engineoilandcompletelysqueezeouttheexcessoilfromthe
element before installing.
Figure 18. Spark Plug Gap
ENGINEOIL
1. Drain the engine oil when the oil is warm as shown in
Figure 19.
2. Remove the oil drain bolt and sealing washer and allow
the oil to drain into a suitable container.
3. Replace engine oil with recommended type oil as listed
in Table 5. Engine oil capacity is 1.16 quarts (1.1 liters).
DO NOT overfill.
4. Install drain bolt with sealing washer and tighten se-
curely.
Figure 20. Engine Air Cleaner
Figure 19. Engine Oil (Draining)
STOW T-20H TRASH PUMP — PARTS MANUAL— REV. #0 (05/29/03) — PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
STOWT-20H — PREPARATION FOR LONG -TERM STORAGE
Pump Storage
For storage of the pump for over 30 days, the following is
required:
z
z
Drain the fuel tank completely.
Run the engine until the fuel in the injection system is
completely consumed.
z
Completely drain used oil from the engine crankcase
and fill with fresh clean oil, then follow the procedures
described in the engine manual for engine storage.
z
z
Remove the drain plug from the pump and drain out any
water from left in the housing.
Remove the pump cover and clean inside of pump
housing. Coat inside of pump housing with a light film of
oil to reduce corrosion. A spray can of oil works well for
this application.
z
z
z
Cover suction and discharge ports with duct tape to
prevent any foreign matter from falling into pump.
Cover pump and engine with plastic covering or
equivalent and store in a clean, dry place.
To protect the water cooled-seals, place one-half pint of
lubricating oil (new or used) through the discharge opening
on the pump and crank the engine several times. This
will prevent excessive corrosion and also keep the
mechanical seal lubricated.
PAGE 24 —STOW T-20H TRASH PUMP — PARTS MANUAL — REV. #0 (05/29/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
STOW T-20H TRASH PUMP — PARTS MANUAL— REV. #0 (05/29/03) — PAGE 25
Download from Www.Somanuals.com. All Manuals Search And Download.
STOWT-20H — TROUBLESHOOTING (ENGINE)
TABLE 7. ENGINE TROUBLESHOOTING
SYMPTOM
Difficult to start
POSSIBLE PROBLEM
SOLUTION
Ignition plug being bridge?
Carbon deposit at ignition?
Check ignition system.
Clean or replace ignition.
Replace insulators.
Fuel is available but spark plug
will not ignite. (Power available
at high tension cable).
Short circuit due to defective
insulators?
Improper spark gap?
Set spark plug gap to the correct gap.
Check stop switch circuit. Replace stop switch if defective.
Replace ignition coil.
Short circuit at stop switch?
Ignition coil defective?
Fuel is available but spark plug
will not ignite. (Power NOT
available at high tension cable).
Muffler clogged with carbon
deposits?
Clean or replace muffler.
Mixed fuel quality is
inadequate?
Check fuel to oil mixture.
Fuel is available and spark plug
ignites (compression normal).
Fuel in use inadequate (water,
dust)?
Flush fuel sytem and replace with fresh fuel.
Air Cleaner clogged?
Defective cylinder head gasket?
Cylinder worn?
Clean or replace air cleaner.
Tighten cylinder head bolts or replace head gasket.
Replace cylinder.
Fuel is available and spark plug
ignites (compression low ).
Spark plug loose?
Tighen spark plug.
Operation not satisfactory
Air cleaner clogged?
Air in fuel line?
Clean or replace air cleaner.
Bleed (remove air) from fuel line.
Not enough power available
(compression normal, no miss-
firing).
Fuel level in carbureator float
chamber improper?
Adjust carbureator float
Carbon deposits in cylinder?
Ignition coil defective?
Clean or replace cylinder
Flush fuel sytem and replace with fresh fuel.
Replace ignition wires, clean ignition.
Flush fuel sytem and replace with fresh fuel.
Not enough power available
(compression normal, miss-
firing).
Ignition plug often shorts?
Fuel in use inadequate (water,
dust)?
Excessive carbon depostion in
combustion chamber?
Clean or replace crankcase.
Clean or replace muffler.
Engine overheats.
Exhaust or muffler clogged with
carbon.
Spark plug heat value incorrect? Replace spark plug with correct type spark plug.
PAGE 26 —STOW T-20H TRASH PUMP — PARTS MANUAL — REV. #0 (05/29/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOWT-20H — TROUBLESHOOTING (ENGINE/PUMP)
TABLE 7. ENGINE TROUBLESHOOTING (Continued)
SYMPTOM
POSSIBLE PROBLEM
SOLUTION
Operation not satisfactory
Governor adjustment improper?
Governor spring defective?
Fuel flow erratic?
Adjust governor to correct lever.
Clean or replace ignition.
Check fuel line.
Rotational speed fluctuates.
Air taken in through suction
line?
Check suction line.
Dust in rotating part?
Spring spring failure?
Clean recoil starter assembly.
Replace sprial spring.
Recoil starter not working
properly.
TABLE 8. PUMP TROUBLESHOOTING
SYMPTOM
POSSIBLE PROBLEM
SOLUTION
Not enough priming water in the housing?
Engine speed too low?
Add water.
Increase throttle.
Clean strainer.
Strainner plugged?
Suction hose damaged?
Replace or repair hose, and clamps
Check that fittings are tight and properly sealed.
Move pump closer to water.
Air leak at suction port?
Pump does not take on water.
Pump is located too high above water line?
Debris collecting in pump housing?
Clean pump housing.
Adjust clearance by adding shims or replace impeller.
Min. .006" - Max. .020"
Too much distance between impeller and volute.
Water leaking out weep hole between pump and Check condition of mechanical seal and gaskets,
engine?
between pump end and engine housing.
Engine speed too low?
Increase throttle speed.
Pump takes in water, little or no Suction strainer partially plugged?
Clean strainer.
discharge.
Impeller/Volute worn?
Adjust clearance by adding shims or replace
impeller/volute
Tighten, replace or add clamp. (Keep extra seals on
pump)
Fittings/clamps are not sealed properly?
Suction hose leaks at inlet.
Hose diameter is too large?
Use smaller diameter hose or replace hose.
Check pressure, add additional clamp.
Check hose.
Pressure too high?
Discharge does not stay on
coupling.
Hose kinked or end blocked?
Impeller jammed or blocked?
Open pump cover and clean dirt and debris from
inside housing.
Impeller does not turn: pump is
hard to start.
Adjust clearance by removing shim from behind
impeller.
Impeller and volute binding?
Defective engine?
See Engine Owner's Manual.
STOW T-20H TRASH PUMP — PARTS MANUAL— REV. #0 (05/29/03) — PAGE 27
Download from Www.Somanuals.com. All Manuals Search And Download.
STOWT-20H — EXPLANATION OF CODE IN REMARKS COLUMN
How to read the marks and remarks used in this parts
book.
he contents of this catalog are
ubject to change without notice.
Items Found In the “Remarks” Column
Serial Numbers-Where indicated, this indicates a serial
number range (inclusive) where a particular part is used.
Model Number-Where indicated, this shows that the
corresponding part is utilized only with this specific model
number or model number variant.
Items Found In the “Items Number” Column
All parts with same symbol in the number column, , #,
+
, %, or
*
>
, belong to the same assembly or kit..
If more than one of the same
reference number is listed, the
last one listed indicates newest (or
latest) part avaliable.
PAGE 28 —STOW T-20H TRASH PUMP — PARTS MANUAL — REV. #0 (05/29/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOWT-20H — SUGGESTED SPARE PARTS
STOWT-20H TRASH PUMP 1TO 3 UNITSWITH
HONDA GX160K1TX2 ENGINE
Qty.
P/N
Description
2 ............ KITT20H ............... KIT, PUMP, MECHANICAL SEAL, O-RINGS
2 ............ 0631211101 .......... DRAIN CAP, FLOODING
2 ............ 0480350300 .......... O-RING FLOODING DRAIN CAP
1 ............ 0811582543 .......... MECHANICAL SEAL SLEEVE
1 ............ 0480240160 .......... O-RING, MECHANICAL SEAL SLEEVE
1 ............ 9395030030 .......... IMPELLER
3 ............ 17210ZE1505 ....... ELEMENT AIR CLEANER DUAL
3 ............ 9807956846 .......... SPARK PLUG
1 ............ 17620ZH7023 ....... CAP, FUEL WITH GASKET
1 ............ 28462ZH8003 ....... ROPE STARTER
1 ............ 1317350350 .......... CHECKVALVE
Part number on this Suggested
Spare Parts List may super cede/
replace the P/N shown in the text
pages of this book.
STOW T-20H TRASH PUMP — PARTS MANUAL— REV. #0 (05/29/03) — PAGE 29
Download from Www.Somanuals.com. All Manuals Search And Download.
STOWT-20H — PUMP ASSY.
PAGE 30 —STOW T-20H TRASH PUMP — PARTS MANUAL — REV. #0 (05/29/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOWT-20H — PUMP ASSY.
PUMP ASSY.
NO.
1
2
3
4
5
6
7
8
PART NO.
PART NAME
QTY.
1
1
1
1
1
1
1
1
1
2
2
2
1
1
1
1
REMARKS
GX160K1TX2
1841100010
9349100020
1841100160
1841100171
1841100740
1247100250
1841040030
1841000131
07904330200014
92950001900014
0483400700
0489353850
0489452300
0482200750
0480240160
0480350300
1841330410
1269330370
1317350350
0631211101
0811582543
0801123325
0723302040
1841200270
1247220280
0641400430
92952140100018
18412140200018
07472304050
1201390610
0191150525
0451250080
0131151235
0135051235
0135051295
ENGINE, HONDA
CASING NPS3"
CASING COVER
SUCTION COVER NPS3"
DRAIN COVER
SUCTION PLATE
DRAIN COVER HANDLE
IMPELLER
VOLUTE CASING
NIPPLE NPS3"×NPT3"
DRAIN COVER SET HANDLE
O’RING (NIPPLE)
O’RING (CASING) f3.5×f385
O’RING (DRAIN COVER) f4.7×f230
O’RING (VOLUTE CASING)
O’RING (MECHANICAL SEAL S
O’RING (FLOODING DRAIN CAP
PACKING, SUCTION PLATE
PACKING, SUCTION COVER
CHECKVALVE
CAP, FLOODING DRAIN
MECHANICAL SEAL SLEEVE ............................ 1 ............... f25.4XF30X56L
MECHANICAL SEAL ........................................... 1 ............... CERAMIC×CUB F30
CUSHION RUBBER
BOLT, HINGE M16×90
9
10
11
12
13
*
14
*
15
*
16
*
17
2
1
1
1
18
19
20
21
22
2
23
24
*
4
2
2
2
1
1
1
1
4
4
2
2
2
25
26
27
28
29
30
31
32
33
34
35
36
PIN, HINGE f12×65
SPLIT PIN 4×30
PIPE FRAME
ENGINE BASE
STRAINER NPT2"
PLATE, CASING COVER SET
BOLT (CASING COVER) M8X20
SEAL WASHER M8
CAP SCREW (CASING) M12×35
CAP SCREW SET W/SEAL RING M12×35
CAP SCREW SET W/SEAL RING M12×95
37
38
39
40
41
42
43
44
45
0131150830
0141050825
0141090510
0181050820
0105050840
0105051035
0209150080
0205450100
0401450050
CAP SCREW (SUCTI ON) M8×30
SCREW (DRAIN COVER HANDLE) M8×25
SCREW (CHECKVALVE) M5×10
BOLT WITH SPRINGWASHER M8×20
BOLT (ENGINE) M8×40
4
2
2
2
4
2
4
10
2
BOLT (PUMP) M10×35
FLANGE NUT (ENGINE) M8
NUT (PUMP CUSHION RUBBER) M10
WASHER
STOW T-20H TRASH PUMP — PARTS MANUAL— REV. #0 (05/29/03) — PAGE 31
Download from Www.Somanuals.com. All Manuals Search And Download.
STOWT-20H — PUMP ASSY.
PUMP ASSY.
PAGE 32 —STOW T-20H TRASH PUMP — PARTS MANUAL — REV. #0 (05/29/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOWT-20H — PUMP ASSY.
PUMP ASSY.
NO.
46
47
48
49
PART NO.
PART NAME
WASHER M8
QTY.
2
2
10
2
1
1
2
2
REMARKS
0401450080
0451250080
0451250100
18410002000014
0852832516
0852852516
0458220080
0105090820
KITT20H
SPRING WASHER M8
SPRINGWASHER M10
DRAIN COVER PUSH PLATE
ADJUST LINER “45×25.4 t0.3
ADJUST LINER “45×25.4 t0.5
SEAL WASHER M8
50
50-1
51
52
53
*
*
BOLT (VOLUTE CASING) M8×20
KIT, PUMP ........................................................ 1 ......... INCLUDES ITEMS W/
*
STOW T-20H TRASH PUMP — PARTS MANUAL— REV. #0 (05/29/03) — PAGE 33
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1TX2 ENGINE — AIR CLEANER (DUAL) ASSY.
AIR CLEANER (DUAL) ASSY.
PAGE 34 —STOW T-20H TRASH PUMP — PARTS MANUAL — REV. #0 (05/29/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1TX2 ENGINE — AIR CLEANER (DUAL) ASSY.
AIR CLEANER (DUAL) ASSY.
NO.
1
2
PART NO.
PART NAME
QTY. REMARKS
16271ZE1000
17210ZE1505
17218ZE1505
17230ZE1820
17232891000
17238ZE7010
17239ZE1000
17410ZE1020
90201415000
90325044000
90325044000
957010602000
GASKET, ELBOW
1
ELEMENT, AIR CLEANER (DUAL)............... 1 ...... INCLUDES ITEMS W/
FILTER (OUTER)
COVER, AIR CLEANER (DUAL)
GROMMET, AIR CLEANER
COLLAR, AIR CLEANER
COLLAR B, AIR CLEANER
ELBOW, AIR CLEANER ............................... 1 ...... INCLUDES ITEMS W/#
NUT, CAP (6 MM)
WINGNUT, TOOL BOX SETTING
WINGNUT, TOOL BOX SETTING
BOLT, FLANGE (6 X 20)
*
3
*
4
1
1
1
2
1
5
*
6#
7#
8
9
2
1
1
1
11
12
13
STOW T-20H TRASH PUMP — PARTS MANUAL— REV. #0 (05/29/03) — PAGE 35
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1TX2 ENGINE — CAMSHAFT ASSY.
CAMSHAFT ASSY.
PAGE 36 —STOW T-20H TRASH PUMP — PARTS MANUAL — REV. #0 (05/29/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1TX2 ENGINE — CAMSHAFT ASSY.
CAMSHAFT ASSY.
NO.
1
2
3
4
PART NO.
PART NAME
QTY. REMARKS
14100ZE1812
14410ZE1010
14431ZE1000
14441ZE1010
14451ZE1013
14568ZE1000
14711ZF1000
14721ZH8810
14751ZF1000
14771ZE1000
14773ZE1000
14781ZE1000
14791ZE1010
90012ZE0010
90206ZE1000
CAMSHAFT ASSY. ...................................... 1 ...... INCLUDES ITEMS W/
*
ROD, PUSH
ARM, VLAVE ROCKER
LIFTER, VALVE
PIVOT, ROCKER ARM
SPRING, WEIGHT RETURN
VALVE, IN.
VALVE, EX. (STELITE)
SPRING VALVE
RETAINER, IN. VALVE SPRING
RETAINER, EX. VALVE SPRING
ROTATOR, VALVE
PLATE, PUSH ROD GUIDE
BOLT, PIVOT (8MM)
NUT, PIVOT ADJ.
2
2
2
2
1
1
1
2
1
1
1
1
2
2
5
6
*
7
8
9
10
11
12
13
14
15
STOW T-20H TRASH PUMP — PARTS MANUAL— REV. #0 (05/29/03) — PAGE 37
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1TX2 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
PAGE 38 —STOW T-20H TRASH PUMP — PARTS MANUAL — REV. #0 (05/29/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1TX2 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
NO.
PART NO.
PART NAME
QTY. REMARKS
1V
16010ZE1812
16011ZE0005
16013ZE0005
16015ZE0831
16016ZH7W01
16024ZE1811
16028ZE0005
16044ZE0005
16100ZH8W51
16124ZE0005
16166ZH8W50
16173001004
16211ZE1000
16212ZH8800
16220ZE1020
16221ZH8801
16610ZE1000
16953ZE1812
16954ZE1811
16956ZE1811
16957ZE1812
16967ZE0811
93500030060H
9430520122
GASKET SET
1
1
1
1
1
1
1
1
2
VALVE SET, FLOAT
FLOAT SET
CHAMBER SET, FLOAT
SCREW SET
SCREW SET, DRAIN
SCREW SET B
CHOKE SET
CARBURETOR ASSY. (BE65B B) ................ 1 ...... INCLUDES ITEMS W/
SCREW, THROTTLE STOP
NOZZLE, MAIN
*
3
*
4
*
5
*
6
*
7
*
8
*
9
*
10
*
11
*
12
*
13
*
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
O-RING
INSULATOR, CARBURETOR
GASKET, INSULATOR
SPACER, CARBURETOR
GASKET, CARBURETOR
LEVER, CHOKE (STD)
LEVER, VALVE
PLATE, LEVER SETTING
SPRING, VALVE LEVER
GASKET, VALVE
CUP, FUEL STRAINER
SCREW, PAN (3 X 6)
PIN, SPRING (2 X 12)
JET, MAIN (#65) OPTIONAL
JET, MAIN (#68) OPTIONAL
JET, MAIN (#70)
14
15
16
17
INCLUDES ITEMS W/#
18
*
19
*
20
*
21
*
22
*
23
*
24#
25
25
99101ZH80650
99101ZH80680
99101ZH80700
99204ZE00350
25
26
*
*
JET, SET, PILOT (#35)
STOW T-20H TRASH PUMP — PARTS MANUAL— REV. #0 (05/29/03) — PAGE 39
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1TX2 ENGINE — CONTROL ASSY.
CONTROL ASSY.
PAGE 40 —STOW T-20H TRASH PUMP — PARTS MANUAL — REV. #0 (05/29/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1TX2 ENGINE — CONTROL ASSY.
CONTROL ASSY.
NO.
1
4
5
6
PART NO.
PART NAME
QTY. REMARKS
16500ZH8030
16551ZE0010
16555ZE1000
16561ZE1020
16562ZE1020
16571ZH8020
16574ZE1000
16575ZH8000
16578ZE1000
16580ZH8030
16584883300
90013883000
90015ZE5010
90114SA0000
93500050250A
9405006000
CONTROL ASSY. ......................................... 1 ...... INCLUDES ITEMS W/
*
ARM, GOVERNOR
ROD, GOVERNOR
SPRING, GOVERNOR
SPRING,THROTTLE RETURN
LEVER, CONTROL
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
7
8
9
*
SPRING, LEVER
*
10
WASHER, CONTROL LEVER
SPACER, CONTROL LEVER
BASE, CONTROL
SPRING, CONTROL ADJUSTING
BOLT, FLANGE (6 X 12) (CT200)
BOLT, GOVERNOR ARM
NUT, SELF-LOCK (6MM)
SCREW, PAN (5 X 25)
NUT, FLANGE (6MM)
*
12
*
13
*
14
*
17
18
19
*
22
*
24
STOW T-20H TRASH PUMP — PARTS MANUAL— REV. #0 (05/29/03) — PAGE 41
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1TX2 ENGINE — CRANKCASE COVER ASSY.
CRANKCASE COVER ASSY.
PAGE 42 —STOW T-20H TRASH PUMP — PARTS MANUAL — REV. #0 (05/29/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1TX2 ENGINE — CRANKCASE COVER ASSY.
CRANKCASE COVER ASSY.
NO.
1
3
4
5
9#
10+
PART NO.
PART NAME
QTY. REMARKS
11300ZE1641
11381ZH8801
15600ZE1003
15600ZG4003
15625ZE1003
15625ZE1003
91202883005
9430108140
COVER ASSY., CRANKCASE (U-TYPE) ..... 1 ...... INCLUDES ITEMS W/
*
GASKET, CASE COVER
CAP ASSY., OIL FILLER ............................. 1 ...... INCLUDES ITEMS W/#
CAP ASSY., OIL FILLER ............................. 1 ...... INCLUDES ITEMS W/+
GASKET, OIL FILLER CAP
GASKET, OIL FILLER CAP
OIL SEAL (25 X 41 X 6)
PIN A, DOWEL (8 X 14)
BOLT, FLANGE (8 X 32)
BEARING, RADIAL BALL (6205)
1
1
1
1
2
6
1
11
12
13
*
957010803200
961006205000
14
*
STOW T-20H TRASH PUMP — PARTS MANUAL— REV. #0 (05/29/03) — PAGE 43
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1TX2 ENGINE — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
PAGE 44 —STOW T-20H TRASH PUMP — PARTS MANUAL — REV. #0 (05/29/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1TX2 ENGINE — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
NO.
1
PART NO.
13310ZE1660
PART NAME
CRANKSHAFT (T-TYPE)
QTY. REMARKS
1
STOW T-20H TRASH PUMP — PARTS MANUAL— REV. #0 (05/29/03) — PAGE 45
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1TX2 ENGINE — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
PAGE 46 —STOW T-20H TRASH PUMP — PARTS MANUAL — REV. #0 (05/29/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1TX2 ENGINE — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
NO.
2
3
3
4
5#
6#
8
PART NO.
PART NAME
QTY. REMARKS
12000ZH8811
15510ZE1023
15510ZE1033
16510ZE1000
16511ZE1000
16512ZE1000
16531ZE1000
16541ZE1000
90131ZE1000
90451ZE1000
90601ZE1000
90602ZE1000
91001ZF1003
91202883005
91353671003
9405010000
CYLINDER ASSY. (OIL ALERT) ................... 1 ...... INCLUDES ITEMS W/
*
SWITCH ASSY., OIL LEVEL........................ 1 ...... USE UP TO ENGINE S/N 4367320
SWITCH ASSY., OIL LEVEL........................ 1 ...... USE FROM ENGINE S/N 4367321
GOVERNOR ASSY....................................... 1 ...... INCLUDES ITEMS W/#
WEIGHT, GOVERNOR
HOLDER, GOVERNORWEIGHT
SLIDER, GOVERNOR
2
1
1
1
2
1
2
1
1
1
1
1
2
1
2
9
SHAFT, GOVERNOR ARM
BOLT, DRAIN PLUG
10
11
12
13
WASHER,THRUST (6MM)
WASHER, DRAIN PLUG (10.2MM)
CLIP, GOVERNOR HOLDER
BEARING, RADIAL BALL (6205)
OIL SEAL (25 X 41 X 6)
O-RING (13.5 X 1.5) (ARAI)
NUT, FLANGE (10MM)
WASHER, PLAIN (6MM)
PIN, LOCK (8MM)
BOLT, FLANGE (6 X 12)
14
*
15
*
16
17
18
19
20
9410106800
9425108000
957010601200
STOW T-20H TRASH PUMP — PARTS MANUAL— REV. #0 (05/29/03) — PAGE 47
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1TX2 ENGINE — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
PAGE 48 —STOW T-20H TRASH PUMP — PARTS MANUAL — REV. #0 (05/29/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1TX2 ENGINE — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
NO.
PART NO.
PART NAME
QTY. REMARKS
1
12210ZH8000
12204ZE1306
12205ZE1315
12216ZE5300
12251ZF1800
12310ZE1010
12391ZE1000
15721ZH8000
90016ZE1000
90043ZE1020
90047ZE1000
9430110160
CYLINDER HEAD......................................... 1 ...... INCLUDES ITEMS W/
*
2
3
GUIDE, VALVE (OS) (OPTIONAL)
GUIDE, EX. VALVE (OS) (OPTIONAL) ........ 1 ...... INCLUDES ITEMS W/#
CLIP, VALVE GUIDE
GASKET, CYLINDER HEAD
COVER, HEAD
GASKET, CYLINDER HEAD COVER
TUBE, BREATHER
BOLT, FLANGE (6 X 13)
BOLT, STUD ( 6 X 109)
BOLT, STUD (8 X 32)
PIN A, DOWELL (10 X 16)
BOLT, FLANGE (8 X 60)
SPARK PLUG (BPR5ES) (NGK)
SPARK PLUG (BPR6ES) (NGK)
1
*
*
4 #
1
1
1
1
1
4
2
2
2
4
1
1
*
5
6
7
8
9
10
11
12
14
15
15
957230806000
9807955846
9807956846
STOW T-20H TRASH PUMP — PARTS MANUAL— REV. #0 (05/29/03) — PAGE 49
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1TX2 ENGINE — FAN COVER ASSY.
FAN COVER ASSY.
PAGE 50 —STOW T-20H TRASH PUMP — PARTS MANUAL — REV. #0 (05/29/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1TX2 ENGINE — FAN COVER ASSY.
FAN COVER ASSY.
NO.
2
4
7
8
11
11
13
14
17
19
PART NO.
PART NAME
QTY.
REMARKS
19610ZE1000ZC
19612ZH8810
90601ZH7013
19630ZH8000
36100ZE1015
36100ZH7003
90013883000
90022888010
34150ZH7003
957010600800
COVER, FAN *NH1* (BLACK)
PLATE, SIDE (OIL ALERT)
CLIP, HARNESS
1
1
1
1
1
1
6
1
1
1
SHROUD
SWITCH ASSY., ENGINE STOP
SWITCH ASSY., ENGINE STOP
BOLT, FLANGE (6 X 12) (CT200)
BOLT, FLANGE (6 X 20) (CT200)
ALERT UNIT, OIL
BOLT, FLANGE (6 X 8)
STOW T-20H TRASH PUMP — PARTS MANUAL— REV. #0 (05/29/03) — PAGE 51
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1TX2 ENGINE — FLYWHEEL ASSY.
FLYWHEEL ASSY.
PAGE 52 —STOW T-20H TRASH PUMP — PARTS MANUAL — REV. #0 (05/29/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1TX2 ENGINE — FLYWHEEL ASSY.
FLYWHEEL ASSY.
NO.
1
2
4
5
5
8
PART NO.
PART NAME
KEY, SPECIAL WOODRUFF (25 X 18)
FAN, COOLING
PULLEY, STARTER
FLYWHEEL
FLYWHEEL (LAMP)
NUT, SPECIAL (14MM)
QTY. REMARKS
13331357000
19511ZE1000
28451ZH8003
31100ZE1010
31100ZE1810
90201878003
1
1
1
1
1
1
STOW T-20H TRASH PUMP — PARTS MANUAL— REV. #0 (05/29/03) — PAGE 53
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1TX2 ENGINE — FUELTANK ASSY.
FUEL TANK ASSY.
PAGE 54 —STOW T-20H TRASH PUMP — PARTS MANUAL — REV. #0 (05/29/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1TX2 ENGINE — FUELTANK ASSY.
FUEL TANK ASSY.
NO.
1
2
3
5
PART NO.
PART NAME
RUBBER, SUPPORTER (107MM)
JOINT, FUEL TANK
TANK, FUEL *NH1* (BLACK)
CAP, FUEL FILLER ...................................... 1 ...... INCLUDES ITEMS W/
GASKET, FUEL FILLER CAP
O-RING (13.5 X 1.5) (ARAI)
NUT, FLANGE (6MM)
BULK HOSE, FUEL (4.5 X 3000)
(4.5 X 140)
QTY. REMARKS
16854ZH8000
16955ZE1000
17510ZE1020ZF
17620ZH7023
17631ZH7003
91353671003
9405006000
1
1
1
*
6
1
1
2
1
*
11
12
13
950014500360M
14
15
9500202080
957010602500
CLIP, TUBE (B8)
BOLT, FLANGE (6 X 25)
2
1
STOW T-20H TRASH PUMP — PARTS MANUAL— REV. #0 (05/29/03) — PAGE 55
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1TX2 ENGINE — IGNITION COIL ASSY.
IGNITION COIL ASSY.
PAGE 56 —STOW T-20H TRASH PUMP — PARTS MANUAL — REV. #0 (05/29/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1TX2 ENGINE — IGNITION COIL ASSY.
IGNITION COIL ASSY.
NO.
1
2
7
11
PART NO.
PART NAME
QTY. REMARKS
30500ZE1033
30700ZE1013
36101ZE1010
90121952000
COIL ASSY., IGNITION
CAP ASSY., NOISE SUPPRESSOR
WIRE, STOP SWITCH (370MM)
BOLT, FLANGE (6 X 25)
1
1
1
2
STOW T-20H TRASH PUMP — PARTS MANUAL— REV. #0 (05/29/03) — PAGE 57
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1TX2 ENGINE — MUFFLER ASSY.
MUFFLER ASSY.
PAGE 58 —STOW T-20H TRASH PUMP — PARTS MANUAL — REV. #0 (05/29/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1TX2 ENGINE — MUFFLER ASSY.
MUFFLER ASSY.
NO.
1
1
3
7
PART NO.
PART NAME
QTY. REMARKS
18310ZF1000
18310ZH8810
18320ZF1H01
18355ZE1000
18381ZH8800
90050ZE1000
90055ZE1000
94001080000S
MUFFLER
1
1
1
1
1
4
1
2
MUFFLER (OPTIONAL)
PROTECTOR, MUFFLER
ARRESTER, SPARK (OPTIONAL)
GASKET, MUFFLER
SCREW, TAPPING (5 X 8)
SCREW, TAPPING (4 X 6) (OPTIONAL)
NUT, HEX (8MM)
8
11
12
15
STOW T-20H TRASH PUMP — PARTS MANUAL— REV. #0 (05/29/03) — PAGE 59
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1TX2 ENGINE — PISTON ASSY.
PISTON ASSY.
PAGE 60 —STOW T-20H TRASH PUMP — PARTS MANUAL — REV. #0 (05/29/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1TX2 ENGINE — PISTON ASSY.
PISTON + RINGS ASSY.
NO.
1
1
1
1
2
2
2
2
3
4
4
5
*
6
PART NO.
PART NAME
QTY.
REMARKS
13010ZH8941
13011ZH8941
13012ZH8941
13013ZH8941
13101ZH8000
13102ZH8000
13103ZH8000
13104ZH8000
13111ZE1000
132A0ZE1000
13200ZE1010
90001ZE1000
90551ZE1000
RING SET, PISTON (STD)
RING SET, PISTON (OS 0.25)
RING SET, PISTON (OS 0.50)
RING SET, PISTON (0.75) OPTION
PISTON (STD)
1
1
1
1
1
1
1
1
1
PISTON (OS 0.25)
PISTON (OS 0.50)
PISTON (0.75)
PIN, PISTON
ROD ASSY., CONNECTING (US 0.25) 1 ......... INCLUDES ITEMS W/
*
ROD ASSY., CONNECTING
BOLT, CONNECTING ROD
CLIP, PISTON PIN (18MM)
1
2
2
STOW T-20H TRASH PUMP — PARTS MANUAL— REV. #0 (05/29/03) — PAGE 61
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1TX2 ENGINE — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
PAGE 62 —STOW T-20H TRASH PUMP — PARTS MANUAL — REV. #0 (05/29/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1TX2 ENGINE — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
NO.
PART NO.
PART NAME
QTY. REMARKS
1
28400ZH8013ZB
28410ZH8003ZB
28420ZH8013
28422ZH8013
28433ZH8003
28441ZH8003
28442ZH8003
28443ZH8003
28461ZH8003
28462ZH8003
90003ZH8003
90008ZE2003
STARTER ASSY., RECOIL “NH1”(BLACK) ............ 1 ..... INCLUDES ITEMS W/
*
2
CASE, RECOIL STARTER “NH1”(BLACK)
REEL, RECOIL STARTER
RATCHET, STARTER
GUIDE, RATCHET
SPRING, FRICTION
SPRING, RECOIL STARTER
SPRING, RETURN
KNOB, RECOIL STARTER
ROPE, RECOIL STARTER
SCREW, SETTING
1
1
2
1
1
1
2
1
1
1
3
*
3
*
4
*
5
*
6
*
7
*
8
*
9
*
10
*
11
*
12
BOLT, FLANGE (6 X 10)
STOW T-20H TRASH PUMP — PARTS MANUAL— REV. #0 (05/29/03) — PAGE 63
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
PAGE 64 —STOW T-20H TRASH PUMP — PARTS MANUAL — REV. #0 (05/29/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1TX2 ENGINE — GASKET KIT ASSY.
GASKET KIT ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
06111ZH8405
11381ZH8800
11381ZH8801
12251ZF1800
12391ZE1000
16212ZH8800
16221ZH8801
18381ZH8800
GASKET KIT............................................. 1...... INCLUDES ITEMS W/
*
2
*
1
*
3
*
4
*
5
*
6
*
7
*
GASKET, CASE COVER
GASKET, CASE COVER
GASKET, CYLINDER HEAD
GASKET, CYLINDER HEAD COVER
GASKET, INSULATOR
GASKET, CARBURETOR
GASKET, MUFFLER
1
1
1
1
1
1
1
STOW T-20H TRASH PUMP — PARTS MANUAL— REV. #0 (05/29/03) — PAGE 65
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1TX2 ENGINE — LABELS ASSY.
LABELS ASSY.
PAGE 66 —STOW T-20H TRASH PUMP — PARTS MANUAL — REV. #0 (05/29/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1TX2 ENGINE — LABELS ASSY.
LABELS ASSY.
NO.
1
PART NO.
PART NAME
QTY. REMARKS
87521ZH8020
87522ZE1810
87522ZH9000
87528ZE1810
87530ZH8810
87532ZH8810
87586ZH7W00
EMBLEM (5.5)
1
1
1
1
1
1
1
2
3
6
7
MARK, CAUTION (EXTERNAL)
LABEL, CAUTION
MARK, CHOKE
LABEL, SPECIFICATION (EXT.)
MARK, OIL ALERT (E)
LABEL, FUEL CAUTION
8
15
STOW T-20H TRASH PUMP — PARTS MANUAL— REV. #0 (05/29/03) — PAGE 67
Download from Www.Somanuals.com. All Manuals Search And Download.
Effective: October 1, 2002
TERMS AND CONDITIONS OF SALE — PARTS
PAYMENT TERMS
5. Partsmustbeinnewandresalablecon- Multiquipreservestherighttoquoteandsell
dition,intheoriginalMultiquippackage(if directtoGovernmentagencies,andtoOriginal
any), and with Multiquip part numbers Equipment Manufacturer accounts who use
Terms of payment for parts are net 10 days.
FREIGHTPOLICY
clearlymarked.
our products as integral parts of their own
products.
All parts orders will be shipped collect or
prepaidwiththechargesaddedtotheinvoice.
All shipments are F.O.B. point of origin.
Multiquip’sresponsibilityceaseswhenasigned
manifesthasbeenobtainedfromthecarrier,
andanyclaimforshortageordamagemustbe
settledbetweentheconsigneeandthecarrier.
6. Thefollowingitemsarenotreturnable:
SPECIALEXPEDITINGSERVICE
a. Obsolete parts. (If an item is in the
price book and shows as being re- A$35.00surchargewillbeaddedtotheinvoice
placedbyanotheritem,itisobsolete.) forspecialhandlingincludingbusshipments,
insuredparcelpostorincaseswhereMultiquip
mustpersonallydeliverthepartstothecarrier.
(such as gaskets, seals, “O” rings,
b. Any parts with a limited shelf life
andotherrubberparts)thatwerepur- LIMITATIONSOFSELLER’SLIABILITY
MINIMUMORDER
chasedmorethansixmonthspriorto
thereturndate.
Multiquip shall not be liable hereunder for
damagesinexcessofthepurchasepriceofthe
The minimum charge for orders from Mul-
tiquipis$15.00net.Customerswillbeasked
for instructions regarding handling of orders
notmeetingthisrequirement.
c. Anylineitemwithanextendeddealer item with respect to which damages are
netpriceoflessthan$5.00.
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
otherspecial,consequentialorincidentaldam-
ages.
d. Special order items.
RETURNEDGOODSPOLICY
e. Electricalcomponents.
f. Paint,chemicals,andlubricants.
g. Decalsandpaperproducts.
h. Itemspurchasedinkits.
Returnshipmentswillbeacceptedandcredit
willbeallowed,subjecttothefollowingprovi-
sions:
LIMITATIONOFWARRANTIES
Nowarranties,expressorimplied,aremade
in connection with the sale of parts or trade
accessoriesnorastoanyenginenotmanufac-
tured by Multiquip. Such warranties made in
connectionwiththesaleofnew,completeunits
are made exclusively by a statement of war-
rantypackagedwithsuchunits,andMultiquip
neitherassumesnorauthorizesanypersonto
assume for it any other obligation or liability
whatever in connection with the sale of its
products.Apartfromsuchwrittenstatementof
warranty, there are no warranties, express,
impliedorstatutory,whichextendbeyondthe
descriptionoftheproductsonthefacehereof.
1. AReturnedMaterialAuthorizationmust
be approved by Multiquip prior to ship-
ment.
7. Thesenderwillbenotifiedofanymaterial
receivedthatisnotacceptable.
2. ToobtainaReturnMaterialAuthorization,
alistmustbeprovidedtoMultiquipParts
Salesthatdefinesitemnumbers,quanti-
ties, and descriptions of the items to be
returned.
8. Suchmaterialwillbeheldforfiveworking
days from notification, pending instruc-
tions.Ifareplyisnotreceivedwithinfive
days,thematerialwillbereturnedtothe
senderathisexpense.
a. Thepartsnumbersanddescriptions
must match the current parts price
list.
9. Creditonreturnedpartswillbeissuedat
dealer net price at time of the original
purchase,lessa15%restockingcharge.
b. The list must be typed or computer
generated.
10. In cases where an item is accepted, for
which the original purchase document
can not be determined, the price will be
basedonthelistpricethatwaseffective
twelvemonthspriortotheRMAdate.
c. The list must state the reason(s) for
thereturn.
d. The list must reference the sales
order(s)orinvoice(s)underwhichthe
itemswereoriginallypurchased.
11. Credit issued will be applied to future
purchasesonly.
e. The list must include the name and
phonenumberofthepersonrequest-
ingtheRMA.
PRICINGANDREBATES
Prices are subject to change without prior
notice.Pricechangesareeffectiveonaspe-
cificdateandallordersreceivedonorafterthat
datewillbebilledattherevisedprice.Rebates
3. AcopyoftheReturnMaterialAuthoriza-
tionmustaccompanythereturnshipment.
4. Freight is at the sender’s expense. All forpricedeclinesandaddedchargesforprice
partsmustbereturnedfreightprepaidto increaseswillnotbemadeforstockonhand
Multiquip’sdesignatedreceivingpoint.
atthetimeofanypricechange.
PAGE 68 —STOW T-20H TRASH PUMP — PARTS MANUAL — REV. #0 (05/29/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
STOW T-20H TRASH PUMP — PARTS MANUAL— REV. #0 (05/29/03) — PAGE 69
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND PARTS MANUAL
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HANDWHEN CALLING
PARTS DEPARTMENT
800-427-1244 or 310-537-3700
FAX: 800-672-7877 or 310-637-3284
SERVICE DEPARTMENT
800-421-1244
FAX: 310- 537-4259
TECHNICAL ASSISTANCE
800-478-1244
FAX: 310- 631-5032
WARRANTY DEPARTMENT
888-661-4279, or 310-661-4279
FAX: 310- 537-1173
STOWCONSTRUCTIONEQUIPMENT
A DIVISION OF MULTIQUIP INC.
POST OFFICE BOX 6254
PARTS DEPARTMENT:
800-427-1244
FAX: 800-672-7877
SERVICE DEPARTMENT/TECHNICAL ASSISTANCE:
800-478-1244
CARSON, CA 90749
310-537-3700 • 888-252-STOW [888-252-7869]
FAX:310-537-1986 • FAX:800-556-1986
E-MAIL: [email protected] • WWW: stowmfg.com
FAX:310-631-5032
Download from Www.Somanuals.com. All Manuals Search And Download.
|