INSTRUCTION
MANUAL
P-30FACC 30 WATT RMS
P-30FACD 30 WATT RMS
P-60FACC 60 WATT RMS
P-60FACD 60 WATT RMS
WARNING: TO PREVENT FIRE
OR SHOCK HAZARD, DO NOT
EXPOSE UNITS NOT
SPECIFICALLY DESIGNED FOR
OUTDOOR USE TO RAIN OR
MOISTURE.
RISK OF ELECTRIC
SHOCK, DO NOT OPEN!
CAUTION: TO REDUCE THE RISK
OF ELECTRIC SHOCK, DO NOT
OPEN COVER. NO USER
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
WARNING: REMOVAL OF THE
COVER SHOULD ONLY BE PER-
FORMED BY QUALIFIED SERVICE
PERSONNEL - NOT USER SER-
VICEABLE. THE UNIT SHOULD
ALWAYS BE UNPLUGGED BEFORE
REMOVING THE COVER, AND
REMAIN UNPLUGGED WHILE THE
COVER IS REMOVED.
PRECAUTIONS
1.Unpacking
After removing the amplifier from the carton, inspect for any exterior damage to
the unit. If damage is noted, notify the carrier at once so that a claim can be
justified. Save all packing material. This is important when the claim is
processed.
2.Ventilation
To offset heat generated by the unit, it is necessary to provide ample ventilation
around the unit. Avoid blocking or impeding the ventilation holes in the unit. To
prevent unnecessary problems, install the unit in a place free from any
vibrations, direct sunlight, humidity or dust circulation.
cabinet
3.Avoid spilling liquids or allowing materials to enter the
If the unit gets wet or any foreign material enters the cabinet, immediately
disconnect the A.C. line cord and consult your dealer or qualified technician.
200 NEW HIGHWAY, AMITYVILLE, NY11701
PHONE : 1-800-645-5516, 631-957-8700 IN METRO NY
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and Connections
FRONT PANEL
FACC
19
17 16 15 14 13
18
EJECT
AUTO-REVERSE
Background Music Cassette Player
PROGRAM
4
5
1
2
3
6
7
8
9
10
11
12
FACD
20
1) MIC-1 input jack (1/4’’ phone jack)
2) Output level indicator
3) MIC-1 Volume control
4) MIC-2 Volume control
5) MIC-3 Volume control
6) MIC-4 Volume control
7) Line input selector switch
8) Line input volume control
9) Bass control
11) Master volume control
12) Power on/off switch with LED indicator
13) Zone 4 selector switch
14) Zone 2 selector switch
15) Zone 1 selector switch
16) Zone 3 selector switch
17) All zone selector switch
18) Auto – reverse cassette player unit
19) FM/AM tuner unit
10)Treble control
20) CD player unit
3
Download from Www.Somanuals.com. All Manuals Search And Download.
REAR PANEL
FACC
10
8
9
11
15
16
17
18 19 20 21 22 23
12
13
14
1
2
5
6
7
3
4
FACD
8
9
10
11
15
16
17
18 19 20 21 22 23
12
13
14
1
2
5
6
7
3
4
1) Speaker outputs
2) Ground
13) AC 115V/230V selector switch BENEATH
SMALL METAL COVER(SEE ABOVE).
14) AC fuse holder
3) FM antenna input
4) AM antenna input
15) LINE output RCA jacks
5) MOH output terminals*
6) Manual muting terminals
16) AUX input RCA jacks
17) MIC-4 (XLR connector) input
18) MIC-3 (XLR connector) input
19) MOH output level control*
20) MIC-1 VOX on/off switch
7) TEL/PAGING input terminals (Balanced)**
8) Zone 1 output terminals
9) Zone 2 output terminals
10) Zone 3 output terminals
21) MIC-2 (XLR connector) input
22) TEL/PAGING input level control**
23) MIC-1 (XLR connector) input
11) Zone 4 output terminals
12) AC input cable receptacle
*MOH = Music on hold
**TEL/PAGING= Connection input terminals for
general or emergency paging.
**TEL/PAGING is not to be connected directly to a
telephone circuit or TNV circuit.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
FRONT PANEL
1) MIC-1 input jack (1/4’’ phone jack). Accepts a balanced low impedance microphone with
a standard 1/4’’ phone plug.
2) Output level indicator. Indicates power output. Do not overload amp.
3) MIC-1 Volume control. Adjusts audio level of MIC-1.
4) MIC-2 Volume control. Adjusts audio level of MIC-2.
5) MIC-3 Volume control. Adjusts audio level of MIC-3.
6) MIC-4 Volume control. Adjusts audio level of MIC-4.
7) Line input selector switch. Allows for selection of high impedance AUX input or music
source from tuner, CD player or cassette player.
8) Line input volume control. Adjusts audio level of line input.
9) Bass control. Low frequency tone control.
10) Treble control. High frequency tone control.
11) Master volume control. Controls all volume levels simultaneously.
12) Power on/off switch with LED indicator. Illuminates when power is on.
13) Zone 4 selector switch. Allows for selection the Zone 4 paging with 70V or 25V line
output. (internally selected, see page 10)
14) Zone 2 selector switch. Allows for selection the Zone 2 paging with 70V or 25V line
output. (internally selected, see page 10)
15) Zone 1 selector switch. Allows for selection the Zone 1 paging with 70V or 25V line
output. (internally selected, see page 10)
16) Zone 3 selector switch. Allows for selection the Zone 3 paging with 70V or 25V line
output. (internally selected, see page 10)
17) All zone selector switch. Allows for selection the All zone paging with 70V or 25V line
output. (internally selected, see page 10)
18) Auto – reverse cassette player unit. (see page 7)
19) FM/AM tuner unit. (see page 8)
20) CD player unit. (see page 7)
REAR PANEL
1) Speaker outputs. Speaker lines must be connected to “COM” and one (and only one) of the
remaining screw terminals.
2) Ground. Cabinet enclosure unit ground.
3) FM antenna input. Connect supplied dipole antenna using supplied 75Ω matching
transformer or coaxial cable to the antenna connector.
4) AM antenna input. Connect the supplied wire loop antenna to the AM spring loaded
terminals.
5) MOH output terminals. Provided two MOH outputs 600 Ohm, 1 Volt and 8 Ohm, 1 Watt.
6) Manual muting terminals. Provides manual contact closure muting of the AUX and MIC-2~4
inputs during paging.
7) TEL / PAGING balanced input terminals. Accepts a balanced telephone paging signal.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
8 ~ 11) Zone 1~4 output terminals. In addition to the normal 70V and 25V line outputs, there
are four groups of 70V or 25V (internally selected, see page 10) line terminals for 4 zones
which can be selected using the push buttons on the front panel.
12) AC input cable receptacle . AC inlet with three pin socket for use of either 115VAC or
230VAC selected by slide switch on rear panel (see page 4). The amplifier is factory set at
115VAC main voltage. (230VAC operation requires AC plug adaptor.)
13) AC 115V/230V selector switch (Beneath small metal cover, see drawing of rear panels
on page 4). Allows for selection of either 115VAC or 230VAC operation. For operating on
230VAC main voltage, remove the small metal cover with a screw driver and slide the
voltage select switch’s actuator from 115VAC(factory set, left side) to 230VAC(right side),
then re-mount the small metal cover with the 230VAC sticker showing on back of small
metal cover and tighten screws.
14) AC fuse holder. Line fuse for the amplifiers:
P–30FACC and P–30FACD
-
2A for 115VAC
1A for 230VAC
3A for 115VAC
1.6A for 230VAC
-
-
P–60FACC and P–60FACD
-
15) LINE output RCA jacks. This booster output supplies the input signal to an additional power
amplifier. This signal is after tone control and master volume control. In this fashion, very large
systems requiring more power can be accommodated.
16) AUX input RCA jacks. High impedance input available with parallel RCA jacks (for stereo
accessories combined for mono.)
17) MIC-4 (XLR connector) input. Accepts a balanced low impedance microphone signal
with an XLR connector.
18) MIC-3 (XLR connector) input. Accepts a balanced low impedance microphone signal
with an XLR connector.
19) MOH output level control. Controls volume of MOH output. (Music on hold)
20) MIC-1 VOX on/off switch. Allows for disabling of MIC-1 input VOX muting of the MIC-2~4
and AUX input during paging. This allows for multiple MIC paging/operation.
21) MIC-2 (XLR connector) input. Accepts a balanced low impedance microphone signal
with an XLR connector.
22) TEL/PAGING input level control. Controls audio level of telephone input.
23) MIC-1 (XLR connector) input. Accepts a balanced low impedance microphone signal
with an XLR connector.
Note: Screw terminal designations: G-GND, HOT-Signal positive, COM-Signal negative/common.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
CD PLAYER UNIT
1. CD display
2. Repeat button
3. Random button
4. Program button
5. CD power on/off button
6. Previous track button
7. Next track button
8. Play/pause button
9. Stop/eject button
CD PLAYER OPERATION
1. Select CD mode with LINE selector switch.
2. Press POWER button on CD player.
3. Load disc (label side up) into player and PLAY begins automatically.
4. Press PAUSE button and symbol ll appears in the display and play is suspended.
Press PAUSE button again to resume play.
5. Pressing
button selects the next track and
button the previous track.
6. Press the RANDOM button, random appears in the display and tracks are played in random
sequence.
7. Press the REPEAT button once and symbol
appears on the display and the current track
appears and indicates repeat
is repeated. When the button is pressed twice the symbol
play of the disc. To cancel these functions press the REPEAT button again.
8. Programming the CD player – in STOP mode.
(a) Press the PROGRAM button
(b) Use the next
or previous
button to select a track.
(c) Press REPEAT button to activate memory of the selected tracks in your program. Repeat
stages (b) and (c) to continue programming.
(d) Press the PLAY button to start the program (Note: The program repeats itself until the CD
player is stopped).
CASSETTE PLAYER UNIT
1. Eject switch
2. Cassette slot
3. Direction indicators
4. Fast wind/program buttons
CASSETTE PLAYER OPERATION
The cassette mechanism is an auto-reverse type which detects when the end of the tape has
been reached and will automatically reverse the direction of the tape and play the opposite side of
the cassette. This function will continue until the cassette is remove from the player.
NOTE: Due to the abrasive nature of cassette tapes some oxide from the tape will be deposited
on to the cassette heads and rollers and therefore the mechanism will need cleaning at regular
intervals. Cleaning cassettes can be purchased from most good hi-fi stores. DO NOT use C120 (120
minute) cassettes.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
INSERTING A CASSETTE
The cassette should be inserted edge first with the exposed tape on the right-hand side, push the
cassette into the mechanism until the cassette drops into position.
REMOVING THE CASSETTE
Firmly press the eject button, the cassette will be automatically ejected.
FAST WIND
The cassette can be fast wound in either direction (forward or reverse) to any position on the tape by
pressing and holding one of the fast wind buttons and will be stopped automatically after releasing the
button.
DIRECTION CHANGE
The side of the cassette currently playing can be reversed to play the other side of the cassette at
any time by pressing both fast wind buttons simultaneously.
FM/AM TUNER UNIT
4
5
6
7
1. Tuner display
2. Memory button
FUNCTION
FM/AM TUNER
3. Shift button
MEMORY
4. FM/AM selection button
5. Frequency Up / Down button
6. Scan button
7. Set memory button
2
3
1
TUNER OPERATION
For FM reception connect the supplied dipole antenna and 75Ω adaptor or an outdoor antenna
using 75Ω coaxial cable to the connector at the rear of the unit. (see page 4)
For AM reception connect the supplied antenna to the AM spring loaded terminals.
1. Select TUNER mode with the Line selector switch.
2. Select FM or AM.
3. Use the UP/DOWN buttons to set a frequency station manually or the SCAN button to
automatically search for the desired station.
4. To program a station press the MEM (Memory) button.
5. Press a MEMORY button (M1 to M5) or SHIFT button and memory button (M6 to M10) to store
a frequency.
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC CAUTION: To assure continued compliance, (example-use only shielded interface cables
when connecting to computer or peripheral devices). Any changes or modifications not expressly
approved by the party responsible for compliance could void the user’s authority to operate this
equipment.
OVERCOMING GROUND LOOP PROBLEMS
If the amplifier is mounted in a rack unit (Use rack mount part # PBM-RK2), or is used with
equipment having its own ground, it is necessary to ensure that ground loops and the associated
problems of hum on the output signal are not introduced by the ground wiring. (see warning)
WARNING
To overcome this problem if it occurs, the electrical and the mechanical ground on the amplifier
may be separated by completely removing the wire connecting the power source to ground.
CONSULT AN ELECTRONICS TECHNICIAN TO ACCOMPLISH THIS TO AVOID POTENTIAL
PERSONAL INJURY OR A HAZARDOUS CONDITION.
SPEAKER CONNECTION
The rear panel of the amplifier contains a 7 screw terminal strip for connection of speakers.
BE CAREFUL TO CONNECT SPEAKERS PROPERLY, see impedance and line voltage instructions
below.
The speaker lines are to be connected directly between the appropriate COM terminal on the 7 screw
terminal strip and the terminal corresponding to the impedance of the speaker(s) or of the line voltage
selected. (70V or 25V)
For 4, 8 and 16 OHM CONNECTIONS (refer to figure 3).
Connect the cables to the terminals on the 7 screw terminal strip provided. Use the screw terminals
which correspond to the impedance of the speaker(s). One lead must always be connected to the
COM. This is just an example. If in doubt consult a qualified technician.
(+)
(+)
(+)
(+)
TWO 8
Ω
SPEAKERS
TWO 4
Ω
SPEAKERS
(IN PARALLEL)
(IN SERIES)
FIGURE 3
9
Download from Www.Somanuals.com. All Manuals Search And Download.
For 25V and 70V CONSTANT VOLTAGE LINE CONNECTIONS
(refer to figure 4).
IMPORTANT NOTICE: When the 25V and 70V constant line voltages are used, a line
matching transformer must be used with each speaker. All
transformers must be connected in parallel.
Jumper positions for
70V or 25V selection.
70V
25V
HOW TO CONNECT LINE MATCHING TRANSFORMERS IN PARALLEL
(25 VOLT LINE OR 70 VOLT LINE)
ALWAYS CONNECT LINE TRANSFORMERS IN PARALLEL
NEVER CONNECT LINE TRANSFORMERS IN SERIES
70V Transf.
25V Transf.
FIGURE 4
SPEAKER IMPEDANCES:
Speaker impedance taps for 4, 8 and 16 Ohm speakers are provided on a terminal strip on the rear
panel of the unit. Also, outputs for 25V and 70V constant line voltage are provided. To connect the
power output directly to a speaker or PA horn or a combination of speakers and/or PA horns which
have a resulting voice coil impedance of 4,8 or 16 Ohm, connect to the COM and the proper
impedance tap on the terminal strip. Be sure the speaker(s) or PA horn(s) is capable of handling a
reasonable power output from the amplifier or permanent damage to the speaker(s) or PA horn(s) may
result. Also, be careful not to overload the amplifier with too many speakers or PA horns. If it is
desired to use a number and variety of speakers, the speakers must be arranged in various series or
parallel arrays to provide proper impedance matching or the 25V or 70V constant line voltage must be
used (parallel connection only). If you are not familiar with impedance matching, consult a professional
installer or technician for advice. If the 25V or 70V constant line voltages are used, a line matching
transformer must be used with each speaker. Again do not overload or use incompatible speakers.
Line transformers are the preferred method for multi-speaker installation.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
CABLE REQUIREMENTS
Output cabling need not be shielded in most cases and should be of sufficient gauge to minimize
losses due to the resistance of the wire over long runs (insertion loss). Cable thinner than 18
gauge is not recommended. Long runs require 16 gauge or heavier.
In some cases, where the output cable is run in close proximity to unshielded intercom cables,
electrical cables, radio transmission antennas or other sources of interference or when the
amplifier is being used for paging from a telephone system, the amplifier may require shielded
output cabling to prevent audio feedback or interference.
PRIORITY PAGE:THE AMPLIFIER FEATURES A VOICE ACTIVATED PRIORITY PAGE CIRCUIT
AND AUTOMATICALLY MUTES ALL PROGRAM MATERIAL (TUNER/TAPE/CD, ETC.) FROM THE
AMPLIFIERS OUTPUT AND PERMITS MICROPHONE # 1 AND THE TELEPHONE INPUT TO
OVERRIDE FOR PAGING ANNOUNCEMENTS.
TELEPHONE LINE: A TELEPHONE LINE INPUT OF 600 OHMS IS PROVIDED.
THERE ARE MANY OTHER FEATURES OFFERED. PLEASE READ MANUAL COMPLETELY.
WHENEVER IN DOUBT ABOUT INSTALLATION, CONSULT WITH A PROFESSIONAL
INSTALLER OR TECHNICIAN OR PERSONAL INJURY, DAMAGE TO THIS AMPLIFIER
AND/OR SPEAKERS MAY RESULT AND YOUR WARRANTY MAY BE VOIDED.
PHANTOM POWER JUMPER POSITIONING
These adjustments are to be made by qualified technical personnel – Be
certain unit is disconnected from A/C power source prior to removing unit’s
cover or electrical shock or injury may result. The unit provides a Phantom
Power DC 15V for electret condenser microphone use.
Jumper location is to enable (ON) or disable (OFF) Phantom Power feature.
Note: Units come with Phantom Power enable (ON).
ON
OFF
JUMP-4
(MIC-4)
ON
OFF
ON
OFF
ON
OFF
JUMP-3
JUMP-1
(MIC-3)
(MIC-1)
(MIC-2)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Determining Your Amplifier Needs
for Sound Systems
Wattage Tap Requirement Chart
Set
Wattage
Taps
Number of
Speakers at
Set Tap
Total Wattage
Requirement per
Tap Setting
Step 1: Fill out Wattage Tap Requirement Chart (to right)
determining the number of speakers that will
be used at each wattage tap for the amplifier.
10
50
Ex A)
5
X
_____________
=
_____________
60
30
20
15
10
7.5
5
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
Step 2: Multiple the number of speakers by each wattage
tap to determine Total Wattage Requirement per
Tap setting (See Ex A).
Step 3: Add all the figures in shaded area to determine
the total Wattage Requirement for the amplifier.
4
3.75
2.5
2
1.50
1.25
1.00
0.50
0.25
Step 4: Match total Wattage Requirement to the bottom
chart "Recommended Amplifier Wattage Chart"
to determine acceptable RMS Wattage your
amplifier should have.
Step 5: Repeat this process for each amplifier system
required.
0.125 X _____________
Total Sum of Shaded Area
Represents Total Wattage
Requirement
_____________
Recommended Amplifier Wattage Chart
Acceptable Amplifier RMS Wattage
15 Watt 30 Watt 60 Watt 120 Watt
If Sum Wattage Total is 12 Watts or Less
X
X
X
X
If Sum Wattage Total is between 13 and 24 Watts
If Sum Wattage Total is between 25 and 48 Watts
If Sum Wattage Total is between 49 and 96 Watts
If Sum Wattage Total is between 97 and 204 Watts
If Sum Wattage Total is between 205 and 216 Watts
If Sum Wattage Total is between 217 and 240 Watts
If Sum Wattage Total is between 241 and 288 Watts
X*
X*
X*
X*
X
X
X
X*
X*
X*
X*
X
X
X
X*
X*
X*
X*
X*
X*
X*
X*
* RMS Amplifier used in conjuction with Speco Technologies’ P-240A Power Booster Amp
For more information contact us at:
Toll Free: 1-800-645-5516 In Metro NY: 631-957-8700 Fax: 631-957-9142 or 631-957-3880
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Specifications
Type
Model
PA Amplifier with Music Sources
P - 30FACD P - 60FACC
AC 115V/230V ,50/60Hz ±10% , Switchable
P - 30FACC
P - 60FACD
Supply
Main Voltage
Output power
Music Max
RMS Rated
45W
30W
45W
30W
90W
60W
90W
60W
Outputs
Speaker outputs:
4Ω,8Ω,16Ω,25V,70V
Line out:600Ω,1V
MOH output :
ZONE outputs:
8Ω 1Watt / 600Ω,1V balanced. 25V or 70V 4 zones + All
Inputs
MIC-1:250Ω,1mV,balanced with phantom power selectable (Jump 1)
MIC-2:250Ω,1mV,balanced with phantom power selectable (Jump 2)
MIC-3:250Ω,1mV,balanced with phantom power selectable (Jump 3)
MIC-4:250Ω,1mV,balanced with phantom power selectable (Jump 4)
AUX:47KΩ,200mV,unbalanced.
See page 11
TEL: 0.1~1V,600Ω,adjustable, balanced
Frequency response
Total harmonic distortion
Signal to noise ratio
60~15K Hz at ±3dB
Less than1% at 1KHz, at rated power
All Volume Controls C.C.W : 75dB below rated power.
MIC-1~MIC-4 : 60 dB below rated power
AUX : 70 dB below rated power
TEL : 70 dB below rated power
Tone Controls
Controls
Bass : ±10 dB at 100Hz
Treble: ±10 dB at 10KHz
MIC-1~MIC-4 volume controls
Line(AUX/Tuner/CD/Cassette) volume control
Master volume control
TEL input level control
MIC-1 VOX on/off switch
MOH output level control
Tone controls (Bass, Treble)
Zone1, Zone 2, Zone 3, Zone 4 and All zone
AC 115V / 230V Voltage Selector Switch.
Output level meter (3 LEDS)
Indicators
AC power consumption
Priority (VOX)
100 VA
100 VA
170 VA
170 VA
Priority level (Using for MIC-1, the XLR connector or phone jack)
TEL / Emer MIC-1 MIC-2 MIC-3 MIC-4 AUX / Tuner/ CD-Tape
3
2
1
1
1
1
Dimensions ( H x W x D )
Weight
3.5”(H) x 16.9”(W) x 11.8”(D)
Approx :15.4 lbs Approx : 18.7 lbs
Approx : 15.4 lbs
Approx : 18.7 lbs
Color
Mounting options
Music Source
Black
Table top or, 19” rack mountable(Use # PBM-RK2 rack mount bracket)
TM-2 : FM / AM Digital Tuner
Unit
TM-2 : FM / AM Digital
Tuner Unit
TM-2 : FM / AM Digital Tuner TM-2 : FM / AM Digital
Unit
Tuner Unit
CD-2 : CD player unit
CD-2 : CD player unit
CP-2 : Auto-reverse cassette
player unit
CP-2 : Auto-reverse cassette
player unit
CP-2 Auto-Reverse Cassette Player Unit
CD-2 CD Player Unit
Type
Model
WOW / Flutter
Tape Speed
Frequency response
S / N
Auto-Reverse Cassette Player Unit
CP-2
Type
Model
Distortion
S / N
CD Player Unit
≦ 0.45 %
CD-2
2940 ~ 3090 Hz
125Hz ~ 6.3KHz ± 4dB
≧ 40 dB
≦ 3 %
500 mV (0~1V adjustable)
< 0.1 %
>80 dB
850 mV
Output
Distortion
Output
Functions
Eject/stop, Pause/play, Next, Previous,
Power, Program, Random, Repeat.
Functions
Eject, Auto-reverse, Program
TM-2 FM/AM Digital Tuner Unit with 20 Programmable Presets
Type
Model
FM / AM Digital Tuner Unit
TM-2
Tuning range
FM: 87.5~108 MHz
AM: 522~1620 KHz
FM: 2ì V ( 26 dB S /N )
AM: 30ì V ( 20 dB S /N )
30Hz ~ 15 KHz (+1 / -3 dB)
Sensitivity
Frequency response
Distortion
S / N
Output
< 1 %
>63 dB (1 mV, FM )
500 mV (0~1V adjustable)
Functions
FM/AM, Down, Up, Scan, Mem
M1, M2, M3, M4, M5, Shift
13
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ
ꢁ
ꢂ
ꢃ
ꢄ
ꢅ
ꢄ
ꢁ
ꢄ
ꢁ
ꢄ
ꢃ
ꢂ
ꢁ
ꢄ
ꢁ
ꢀ
ꢊ
ꢄ
ꢁ
ꢀ
ꢊ
ꢄ
ꢃ
ꢂ
ꢁ
ꢀ
ꢊ
ꢚ5ꢗꢊꢀ
ꢚ5ꢗꢊꢁ
ꢚ5ꢗꢊꢂ
ꢇ ꢈꢉ
ꢂꢌꢉꢐꢄꢁ
ꢂꢑꢒꢈꢊꢀ
ꢂꢑꢓꢈꢊꢀ
ꢊ ꢈꢉ
ꢎ ꢈꢉ
ꢎ ꢈꢐ
ꢃ
ꢊꢋꢌꢍꢉ
ꢂꢅ
ꢏꢅ
ꢃ
ꢀ
ꢊ
ꢃ
ꢀ
ꢊ
ꢀ
ꢊ
ꢃ
ꢃ
ꢓꢌꢊꢔꢀ ꢙꢚꢂꢇꢉ ꢈꢐ ꢒꢀꢈꢗ
ꢃꢓꢌꢊ ꢀ ꢙꢚꢂꢇꢉꢈꢈꢐ ꢒꢀꢈꢗ
ꢂꢑꢒꢈꢊꢀ ꢌꢅꢉꢛꢒꢀ ꢂꢅꢑꢈꢒꢈꢄꢁ ꢏꢅꢑꢈꢒꢈꢚꢁ
ꢂꢑꢓꢈꢊꢀ ꢌꢅꢉꢀ ꢂꢅꢑꢈꢓꢈꢄꢁ ꢏꢅꢑꢈꢓꢈꢁ
ꢒꢔꢈꢈꢕ ꢈꢖ
ꢗꢘꢈꢈꢕ ꢈꢖ
ꢂ
ꢂ
ꢂ
ꢂ
ꢋꢗꢊꢄ
ꢈ
ꢈ
ꢋꢗꢊꢁ
ꢋꢗꢊꢂ
ꢚ5ꢗꢊꢃ
ꢄ
ꢚ5ꢗꢊꢄ
ꢄ
ꢄ
ꢁ
ꢀ
ꢊ
ꢄ
ꢁ
ꢀ
ꢊ
ꢁ
ꢀ
ꢊ
ꢁ
ꢀ
ꢊ
ꢋꢑꢊꢁ
ꢌꢕꢙꢒꢕꢙ
ꢖꢃꢒ
ꢋꢔꢛꢜꢈ
ꢛꢜꢈ ꢛꢜꢈ ꢛꢜꢈ
ꢖ
ꢉꢏꢗꢊꢀ
ꢍꢊꢘꢐꢁꢄꢘ
6ꢌꢋꢜꢃ
ꢌ$
ꢗ
ꢍ
ꢅ
ꢄ
ꢃ
ꢂ
ꢁ
ꢀ
ꢗ
ꢃ
ꢂ
ꢃ
ꢃ
ꢂ
ꢃ
ꢂ
ꢍ
ꢍꢊꢘꢐꢁꢄꢘ
6ꢌꢋꢜꢂ
ꢌ$
ꢎꢄꢊꢗ
ꢀꢁꢊꢏ
ꢅ
ꢃ
ꢄꢊꢗ
ꢂ
ꢉꢕ$ꢒꢔꢀ
ꢋꢄꢊꢅ
ꢙꢂ
ꢄ
ꢃ
ꢂ
ꢁ
ꢀ
ꢋꢀꢊꢀ
ꢋꢀꢊꢗ
ꢙꢃ
ꢖ
ꢎꢄꢊꢀ
ꢃꢏꢍ
ꢃꢍꢊꢒ
ꢋꢄꢊꢀ
ꢙꢁ
ꢄꢊꢅ
ꢀꢊꢁ ꢄꢊꢍꢖ
ꢀꢊꢐꢄꢊ
ꢍꢊꢘꢐꢁꢄꢘ
6ꢌꢋꢜꢁ
ꢌ$
ꢙꢗ
ꢋꢀꢊꢅ
ꢙꢃ
ꢋꢗꢊꢀ
ꢄꢊꢄ
ꢀꢊꢐꢄꢊ
ꢄ
ꢓ
ꢉꢄꢊꢀ
ꢄꢀꢁ
ꢎꢄꢊꢁ
ꢃꢏꢍ
ꢎꢄꢀꢊ
ꢃꢏꢍ
ꢕꢄꢊꢀꢇ
ꢁꢊꢅꢗ
ꢄꢊꢑ
ꢍ
ꢀ
ꢍ
ꢀ
ꢍꢊꢘꢐꢁꢄꢘ
6ꢌꢋꢜꢀ
ꢌ$
ꢄꢀꢊ
ꢁꢁꢐꢁꢄ
ꢁ
ꢀꢊꢁ
ꢄꢊꢃ
ꢀꢊꢐꢄꢊ
ꢎꢄꢊꢄ
ꢀꢏ
ꢆꢋꢌꢋ
ꢂ
ꢀꢊꢐꢄꢊ
ꢋꢑꢊꢄ
ꢅ
ꢄꢀꢀ
ꢂꢂꢒ
ꢔ
ꢋꢑꢊꢃ
ꢖ
ꢎꢄꢊꢑ
ꢄꢏꢅ
ꢎꢄꢀꢀ
ꢂꢏꢂ
ꢀ
ꢄꢊꢂ
ꢃꢍꢁ
ꢎꢄꢊꢂ
ꢃꢍꢏ
ꢎꢄꢊꢅ
ꢃꢏꢍ
ꢎꢄꢊꢃ
ꢀꢏ
ꢙꢁ
ꢋꢄꢊꢁ
ꢖ
ꢄꢊꢁ
ꢄꢀꢃ
ꢄꢁꢅ
ꢄꢃꢊ
ꢖ
ꢀꢁꢊꢏ
ꢎꢄꢊꢍ
ꢃꢍꢁ
ꢖ
ꢃꢍꢂ
ꢄꢀꢑ
ꢎꢄꢀꢗ
ꢀꢁꢊꢏ
ꢄꢊꢀ
ꢖ
ꢖ
ꢉꢕ$ꢒꢔꢁ
ꢖ
ꢖ
ꢖ
ꢖ
ꢖ
ꢖ
ꢖ
ꢖ
ꢖ
ꢖ
ꢖ
ꢍꢒ
ꢀ
ꢌꢙ
ꢖ
ꢍꢊꢘ
ꢃꢍꢊꢒ
ꢖ
ꢎꢄꢀꢁ
ꢃꢏꢍ
ꢎꢄꢃꢑ
ꢄꢀꢍ
ꢀꢊꢁ ꢄꢀꢗꢖ
ꢀꢊꢐꢄꢊ
ꢁꢄꢘ
ꢄꢀꢅ
ꢀꢊꢐꢄꢊ
ꢂ
ꢀꢊꢊ
ꢓ
ꢔ
ꢌ$
ꢉꢄꢊꢁ
ꢄꢁꢃ
ꢎꢄꢀꢂꢖ
ꢃꢏꢍ
ꢎꢄꢁꢀ
ꢃꢏꢍ
ꢎꢄꢁꢁ
ꢂꢏꢂ
ꢀꢁꢂꢃꢂꢀꢄꢅ
ꢕꢄꢊꢀꢖꢆ
ꢁꢊꢅꢗ
ꢌꢕꢙꢒꢕꢙ
ꢄꢁꢊ
ꢀꢅꢖ!"#
ꢄꢁꢀ
ꢁꢁꢐꢁꢄ
ꢁ
ꢄꢀꢄ
ꢀꢊꢐꢄꢊ
ꢀꢊꢁ
ꢎꢄꢀꢅ
ꢀꢏ
ꢋꢀꢀꢊ
ꢙꢄ
ꢆꢋꢌꢋ
ꢂ
ꢀꢊꢐꢄꢊ
ꢗ!"#
ꢃ!"#
ꢁ
ꢎꢄꢁꢂ
ꢃꢏꢍ
ꢄꢁꢁ
ꢂꢂꢒ
ꢎꢄꢁꢊ
ꢄꢏꢅ
ꢀ
ꢄꢁꢂ
ꢃꢍꢁ
ꢎꢄꢀꢃ
ꢃꢍꢏ
ꢎꢄꢀꢍ
ꢃꢏꢍ
ꢎꢄꢀꢄ
ꢀꢏ
ꢌ$
ꢃꢍꢁ
&ꢄꢊꢀ
ꢈꢅꢅꢍ
ꢀꢁꢊꢏ
ꢎꢄꢀꢑ
ꢎꢄꢂꢊ
ꢃꢍꢂ
ꢄꢀꢂ
ꢖ
ꢖ
ꢉꢕ$ꢒꢔꢂ
ꢖ
ꢖ
ꢖ
ꢄꢂꢂ
ꢖ
ꢖ
ꢖ
ꢀꢁꢊꢏ
ꢖ
ꢎꢄꢁꢃ
ꢃꢏꢍ
ꢃꢍꢊꢒ
ꢄꢂꢁ
ꢀꢊꢁ ꢄꢂꢀꢖ
ꢀꢊꢐꢄꢊ
ꢄꢂꢊ
ꢀꢊꢐꢄꢊ
ꢄ
ꢓ
ꢋꢄꢊꢂ
ꢉꢄꢊꢂ
ꢄꢂꢍ
ꢙꢂ
ꢎꢄꢁꢄ
ꢃꢏꢍ
ꢎꢄꢂꢂ
ꢃꢏꢍ
ꢎꢄꢂꢃ
ꢂꢏꢂ
ꢕꢄꢊꢁꢇ
ꢋꢂꢊꢀ
ꢙꢃ
ꢄꢂꢃ
ꢄꢁꢑ
ꢁꢁꢐꢁꢄ
ꢁ
ꢘꢎꢂꢊꢀ
ꢄꢊꢏꢆ
ꢄꢁꢗ
ꢀꢊꢐꢄꢊ
ꢀꢊꢁ
ꢁꢊꢅꢗ
ꢎꢄꢁꢗ
ꢀꢏ
ꢋꢀꢊꢃ
ꢙꢁ
ꢋꢀꢊꢄ
ꢆꢋꢌꢋ
ꢂ
ꢄꢂꢅ
ꢂꢂꢒ
ꢀꢊꢐꢄꢊ
ꢅ
ꢙꢅ
ꢔ
ꢎꢄꢂꢄ
ꢃꢏꢍ
ꢎꢄꢂꢁ
ꢄꢏꢅ
ꢀ
ꢄꢁꢍ
ꢃꢍꢁ
ꢎꢄꢁꢅ
ꢃꢍꢏ
ꢎꢄꢁꢑ
ꢃꢏꢍ
ꢎꢄꢁꢍ
ꢀꢏ
ꢎꢄꢂꢀ
ꢀꢁꢊꢏ
ꢀ
ꢖ
ꢖ
ꢇꢔ
ꢃꢍꢁ
&ꢄꢊꢁ
ꢈꢅꢅꢍ
ꢖ
ꢀ
ꢒꢙꢖ
ꢃꢍꢂ
ꢄꢁꢄ
ꢇꢓ
ꢄꢊꢀ
ꢖ
ꢄꢄꢊ
ꢀꢊꢊꢐꢀꢅ
ꢖ
ꢖ
ꢉꢕ$ꢒꢔꢃ
ꢖ
ꢖ
ꢖ
ꢄꢃꢄ
ꢎꢄꢃꢁ
ꢀꢁꢊꢏ
ꢀꢀꢄꢐꢁꢂꢊꢘ
ꢈꢄꢊꢀ
ꢖ
ꢖ
ꢎꢄꢂꢅ
ꢃꢏꢍ
ꢖ
ꢘꢎꢂꢊꢁ
ꢄꢊꢏꢆ
ꢃꢍꢊꢒ
ꢎꢄꢄꢊ
ꢀꢊꢏ
ꢋꢂꢊꢗ
ꢙꢁ
ꢋꢂꢊꢍ
ꢙꢁ
ꢋꢂꢊꢅ
ꢙꢂ
ꢄꢃꢅ
ꢀꢊꢁ ꢄꢖꢃꢍ
ꢀꢊꢐꢄꢊ
ꢎꢄꢃꢃ
ꢀꢊꢏ
ꢄꢂꢗ
ꢁꢁꢊꢐꢁꢄ
ꢉꢄꢊꢃ
ꢋꢄꢊꢃ
ꢙꢂ
ꢋꢀꢊꢁ
ꢙꢁ
ꢋꢀꢊꢂ
ꢙꢄ
ꢄꢃꢗ
ꢀꢊꢐꢄꢊ
ꢂ
ꢓ
ꢔ
ꢖ
ꢖ
ꢖ
ꢖ
ꢄꢄꢀ
ꢖ
ꢎꢄꢂꢍ
ꢃꢏꢍ
ꢎꢄꢃꢅ
ꢃꢏꢍ
ꢎꢄꢃꢍ
ꢂꢏꢂ
ꢕꢄꢊꢁꢆ
ꢁꢊꢅꢗ
ꢎꢄꢊꢀ
ꢀꢊꢏ
ꢄꢊꢀ
ꢖ
ꢄꢃꢃ
ꢀꢊꢁ
ꢄꢃꢂ
ꢁꢁꢐꢁꢄ
ꢁ
ꢘꢎꢂꢊꢂ
ꢄꢊꢏꢆ
ꢄꢊꢁ
ꢖ
ꢖ
ꢄꢃꢁ
ꢀꢊꢐꢄꢊ
ꢎꢄꢃꢊ
ꢀꢏ
ꢀ
ꢎꢄꢄꢀ
ꢀꢊꢊ
ꢆꢋꢌꢋ
ꢂ
ꢀꢊꢐꢄꢊ
ꢁ
ꢖ
ꢖ
ꢎꢄꢃꢗ
ꢃꢏꢍ
ꢘꢎꢂꢊꢄ
ꢄꢊꢏꢆ
ꢀ
ꢄꢃꢑ
ꢂꢂꢒ
ꢎꢄꢃꢄ
ꢄꢏꢅ
ꢀ
ꢄꢃꢀ
ꢃꢍꢁ
ꢎꢄꢂꢗ
ꢃꢍꢏ
ꢎꢄꢃꢀ
ꢃꢏꢍ
ꢎꢄꢂꢑ
ꢀꢏ
ꢋꢂꢊꢄ
ꢙꢁ
ꢋꢄꢊꢀ
ꢖ
ꢖ
ꢚꢂꢊꢀꢔꢁ ꢚꢂꢊꢀꢔꢀ
ꢇ ꢈꢉꢆꢊ
ꢃꢍꢁ
&ꢄꢊꢂ
ꢈꢅꢅꢍ
ꢖ
ꢙꢁ
ꢖ
ꢀꢁꢊꢏ
ꢎꢄꢃꢂ
ꢘꢎꢂꢊꢃ
ꢄꢊꢏꢆ
ꢃꢍꢂ
ꢄꢂꢑ
ꢇ
ꢇ
ꢖ
ꢖ
ꢖ
ꢖ
ꢖ
ꢖ
ꢖ
ꢄꢄꢁ
ꢃꢍꢊꢐꢁꢄ
ꢎꢄꢄꢍ
ꢀꢊꢊ
ꢖ
ꢖ
ꢄꢂꢄ
ꢃꢍꢂ
ꢉꢄꢊꢄ
ꢎ
ꢆꢁꢆ
ꢋꢂꢊꢁ
ꢙꢁ
ꢋꢍꢊꢀ
ꢙꢁ
ꢖ
ꢖ
ꢋꢄꢊꢄ
ꢙꢃ
ꢄꢄꢃ
ꢎꢄꢄꢅ
ꢀꢊꢊ
ꢈꢍꢊꢀ
ꢛꢜꢈ
ꢆꢕ%
ꢄꢄꢄ
ꢃꢍꢂ
ꢎꢂꢊꢀ
ꢀꢗꢏ
ꢎꢂꢊꢁ
ꢀꢗꢏ
ꢎꢂꢊꢂ
ꢀꢗꢏ
ꢎꢂꢊꢃ
ꢀꢗꢏ
ꢀꢐꢄꢊ
ꢎꢄꢄꢁ
ꢃꢍꢏ
ꢖ
ꢖ
ꢖ
ꢖ
ꢖ
ꢛꢝꢋꢜꢖꢌꢕꢙ
ꢖ
ꢎꢄꢄꢂ
ꢀꢊꢊ
ꢛꢝꢋꢜꢌꢕꢙ
ꢆꢁ
ꢋꢂꢊꢂ
ꢙꢅ
ꢋꢂꢊꢃ
ꢙꢅ
ꢎ
ꢀꢁꢂꢀꢃꢄꢅꢆ
ꢀꢁꢂꢋꢌꢍꢀꢎꢇꢅ
ꢀ
ꢁꢆꢇꢃꢂꢀꢄꢅ
ꢎꢄꢄꢃ
ꢀꢊꢊ
ꢄꢄꢅ
ꢃꢍꢂ
ꢎꢄꢄꢄ
ꢃꢍꢏ
ꢄꢄꢍ
ꢃꢍꢊꢒ
ꢀ
ꢋꢃꢊꢀ
ꢙꢂ
ꢖ
ꢖ
ꢖ
ꢖ
ꢎꢃꢊꢀ
ꢀꢁꢏ
ꢃꢊꢀ
ꢂꢂꢁ
ꢁ
ꢎꢃꢊꢁ
ꢀꢁꢊꢏ
ꢎꢃꢊꢂ
ꢅꢏꢗ
ꢁ
ꢀ
ꢎꢃꢊꢄ
ꢅꢏꢗ
ꢃꢊꢁ
ꢂꢂꢂ
ꢆ
ꢆ
ꢇꢆꢚꢚ
ꢆ
ꢀꢀꢄꢘꢐꢁꢂꢊꢘ
ꢂ
ꢀꢄꢊꢏ
ꢎꢃꢊꢅ
ꢘꢎꢃꢊꢀ
ꢃꢊꢂ
ꢀꢄꢃ
ꢙꢜꢎ
ꢄꢊꢏꢆꢖ
ꢘꢎꢃꢊꢁ
ꢄꢊꢏꢆꢖ
ꢎꢃꢊꢃ
ꢀꢏꢄ
ꢃꢊꢃ
ꢀꢄꢂ
$ꢆꢚꢙꢜꢎ
ꢘꢎꢃꢊꢂ
ꢁ
ꢙ),3'
ꢚ)4'
ꢇꢌꢆꢕꢌꢂꢍꢇꢏ
ꢀꢁꢂꢃꢄꢅꢆꢇ ꢀꢁꢂꢃꢄꢅꢆꢆ ꢀꢁ ꢃꢄꢅꢆꢇ ꢀꢁ ꢃꢄꢅꢆꢆ
ꢁ
ꢄꢊꢏꢆ
ꢎ'()*)!+
ꢎꢜꢘꢔꢆ
ꢖ
ꢖ
ꢈ/,'2ꢖꢖꢖꢖꢖꢖꢖꢖꢖꢖꢖ
)3'2ꢖꢖꢖꢖꢖꢖꢖꢖꢖꢖꢖꢖꢒꢔꢂꢊ ꢆꢔꢀ
ꢚ"'',ꢖꢖꢖꢖꢖꢖꢀꢖꢖꢖꢖꢖꢖ!-
ꢈ./0+ꢖꢇ12 ꢛꢇ
ꢁ
Download from Www.Somanuals.com. All Manuals Seꢃarch And Download.
ꢀ
ꢁ
ꢂ
ꢄ
ꢅ
ꢀ
ꢁ
ꢂ
ꢃ
ꢄ
ꢅ
ꢀꢁꢁꢂ ꢀꢁꢁꢁ ꢀꢁꢂꢁ
ꢀꢁꢂꢂ ꢀꢁꢂꢊ ꢄꢁꢃꢅ ꢄꢁꢃꢆ
ꢀꢁꢂꢃ
ꢄꢁꢅꢆ
ꢎꢏꢐꢇꢑꢒ
ꢎꢏꢉꢇꢑꢒ
ꢀꢁꢂꢃꢄ ꢀꢁꢂꢃꢄ
ꢅꢄꢆꢇ
ꢅꢄꢆꢇ
ꢄꢁꢆꢇ ꢄꢁꢆꢂ ꢄꢁꢆꢅ ꢄꢁꢆ ꢄꢁꢆꢆ ꢈꢁꢉꢊꢋꢌꢁꢇꢁꢈꢍꢁꢇꢆ ꢓꢔꢏꢁꢇꢁ
ꢉꢊꢈꢋꢌꢍ
ꢎꢏꢐꢇꢑꢒ
ꢎꢏꢉꢇꢑꢒ
ꢈ
ꢈ
ꢉꢊꢈꢋꢌꢍ
ꢈꢀꢉꢂ
ꢀꢉꢖ
ꢈꢀꢉꢃ
ꢊꢀꢁꢁ
ꢀꢍꢄ
ꢛꢀꢁꢖ ꢗꢕꢈ
ꢔꢕ
ꢘꢝꢚ
ꢔꢕꢃꢀꢃꢎ
ꢊꢀꢁꢂ
ꢃꢌ
ꢓꢀꢉꢃ
ꢕꢀꢉꢄ
ꢅ
ꢊꢀꢁꢉ
ꢃꢌꢍ
ꢀꢎꢀꢄ
ꢐ
ꢃꢌꢍ
ꢊꢀꢁꢀ
ꢀꢀꢄ
ꢀꢉꢒꢄꢉ
ꢊꢀꢂꢅ
ꢀꢍ
ꢊꢀꢂꢄ
ꢁꢁꢍ
ꢊꢀꢂꢃ
ꢀꢏ
ꢈꢀꢉꢎ
ꢔꢕꢃꢀꢃꢎ
ꢐ
ꢐ
ꢕꢀꢉꢀ
ꢐ
ꢓꢀꢉꢋ
ꢀꢎꢀꢄ
ꢚꢀꢉꢁ
ꢀꢀꢃ
ꢃꢑꢌꢒꢄꢉ
ꢊꢀꢃꢃ
ꢅꢎꢉꢍ
ꢊꢀꢃꢉ
ꢂ'ꢂ
ꢓꢀꢉꢎ
ꢕꢀꢁꢉ
ꢈꢀꢉꢌ
ꢔꢕꢃꢀꢃꢎ
ꢊꢀꢀꢄ
ꢀꢉꢉ
ꢀꢀꢉ
ꢁꢁꢉꢒꢁꢄ
ꢀꢀꢀ
ꢃꢌꢂ
ꢅꢉꢉ$)*
ꢁ
ꢅ
ꢊꢀꢃꢄ
ꢀꢄꢍ
ꢓꢀꢉꢌ
ꢀꢎꢀꢄ
(ꢀꢁꢉꢀꢉꢉ
ꢊꢀꢂꢁ
ꢃꢌꢉ
ꢀꢐꢃ
ꢊꢀꢀꢃ
ꢀꢄꢉ
ꢀꢀꢂ
ꢀꢉꢁ
ꢝꢀꢉꢀ
ꢀꢖ
ꢀꢉꢋ
ꢈꢅꢅꢌ
ꢐ
ꢎ
ꢐ
ꢊꢀꢀꢎ
ꢅꢎꢍ
ꢀꢁꢌ
ꢃꢑꢌꢒꢄꢉ
ꢊꢀꢃꢀ
ꢃꢍꢌ
ꢈꢀꢀꢉ
ꢈꢀꢉꢋ
ꢎꢑꢁꢖ
ꢊꢀꢂꢋ
ꢃꢍꢌ
ꢀꢁꢃ
ꢀꢒꢄꢉ
ꢓꢀꢀꢉ
ꢀꢎꢀꢄ
ꢊꢀꢂꢂ
ꢂꢂꢍ
(ꢏꢂꢎꢉꢕ
ꢚꢁ
ꢕꢀꢉꢅ
ꢚꢃ
ꢃꢌꢉꢒꢀꢅ
ꢀꢉꢎ
ꢀꢉꢃ
ꢀꢂꢉ
ꢀꢒꢄꢉ
ꢔꢕꢃꢀꢃꢎ
ꢀꢁꢅ
ꢀꢉꢁ
ꢀꢁꢂ
ꢃꢌꢉ
ꢀ!ꢒꢎ$)*
ꢏꢝꢚ+
ꢗ
ꢐ
ꢐ
ꢂꢐꢜꢐꢄ
ꢀꢐꢉꢐꢜꢐꢀꢐꢁ
ꢌ
ꢊꢀꢂꢌ
ꢀꢏ
ꢊꢀꢀꢌ
ꢀꢉꢒꢉꢑꢄ!
ꢀꢁꢎ
ꢃꢌꢂ
ꢀꢁꢋ
ꢁꢁꢒꢁꢄ
ꢊꢀꢃꢅ
ꢂꢂꢍ
ꢊꢀꢃꢂ
ꢃꢍꢌ
ꢊꢀꢃꢁ
ꢀꢉꢉꢍ
ꢊꢀꢂꢎ
ꢀꢉꢉꢍ
ꢀꢀꢁ
ꢃꢌꢒꢁꢄ
ꢊꢀꢀꢅ
ꢀ
ꢚꢀꢉꢀ
ꢀꢉꢀ
ꢐ
ꢐ
ꢐ
ꢐ
ꢐ
ꢐ
ꢐ
ꢐ
ꢐ
ꢐ
ꢐ
ꢐ
ꢐ
ꢐ
ꢐ
ꢘꢏ (ꢀꢁꢉꢀꢉꢉ
ꢈꢀꢐ
ꢐ
ꢀꢒꢄꢉ
ꢙꢘꢚ
ꢊꢀꢉꢄ
ꢃꢍꢌ
ꢊꢀꢉꢅ
ꢔꢕꢃꢀꢃꢎ
ꢖ"#
ꢊꢁꢀꢀ
ꢂ
ꢀ
ꢀꢉꢉ
ꢖ$%&
ꢀꢉꢂ
ꢃꢑꢌꢒꢄꢉ
ꢊꢀꢉꢀ
ꢅꢎꢉ
ꢊꢀꢉꢁ
ꢀꢏ
ꢊꢀꢉꢌ
ꢀꢏ
ꢊꢀꢉꢎ
ꢂꢂꢍ
ꢊꢀꢉꢋ
ꢂꢍꢂ
ꢐ
ꢝꢀꢉꢂ
ꢌꢎꢀꢁ
ꢐ
ꢈꢀꢉꢁ
ꢔꢕꢃꢀꢃꢎ
ꢂꢑꢂꢖꢐꢄ!
ꢕꢀꢀꢅ
ꢚꢁ
ꢐ
ꢀꢂꢀ
ꢁꢁꢉꢒꢁꢄ
ꢕꢀꢀꢌ
ꢓꢀꢉꢂ
ꢀꢎꢀꢄ
ꢚꢘꢐ ꢕꢀꢁꢉ
ꢀꢂꢁ
ꢀꢉꢒꢄꢉ
ꢊꢀꢉꢃ
ꢁꢁꢍꢐ
ꢀꢉꢄ
ꢀꢒꢄꢉ
ꢈꢀꢉꢀ
ꢔꢕꢃꢀꢃꢎ
ꢚꢁ
ꢓꢀꢉꢁ
ꢀꢎꢀꢄ
ꢝꢀꢉꢃ
ꢌꢎꢀꢎ
ꢐ
ꢐ
ꢐ
ꢚꢁ
ꢊꢁꢀꢁ
ꢂꢑꢂꢒꢉꢑꢄ!
ꢓꢀꢉꢀ
ꢀꢎꢀꢄ
ꢕꢀ
ꢕꢀꢀꢄ
ꢚꢂ
ꢂ
ꢀ
ꢖ$%&
ꢖ"#
ꢀꢉꢁ
ꢀꢉꢂ
ꢊꢀꢉꢂ
ꢂꢋꢉ
ꢚꢁ
ꢀꢉꢉꢒꢁꢄ
ꢀꢉꢃ
ꢊꢀꢀꢁ
ꢁꢌꢍ
ꢊꢀꢀꢉ
ꢀꢏ
ꢕꢀꢀꢃ
ꢐ
ꢐ/!ꢃꢉꢂ
ꢈ
ꢖꢊꢀꢉꢀ
ꢁꢉꢉꢍ
ꢀꢉꢅ
ꢀꢒꢄꢉ
ꢊꢀꢀꢋ
ꢀꢉꢍ
ꢐ
ꢚꢃ
ꢀꢉꢌ
ꢀꢉꢒꢄꢉ
ꢊꢀꢀꢀ
ꢀꢉꢉꢍ
ꢐ
ꢇꢛ
ꢇꢜ
ꢖꢊꢀꢉꢁ
ꢀꢉꢍ
ꢕꢁ
ꢐ
ꢐ
ꢐ
ꢐ
ꢐ
ꢐ
ꢐ
ꢐ
ꢐ
ꢀꢂꢂ
ꢀꢉꢒꢄꢉ
ꢐ
ꢐ
ꢖꢊꢀꢉꢂ
ꢀꢉꢍꢆ
ꢐ
ꢐ
ꢐ
ꢐ
ꢈꢀꢀꢎ
ꢚꢁ
ꢀꢂꢃ
ꢁꢁꢉꢒꢁꢄ
ꢀꢃꢂ
ꢀꢉꢉꢒꢁꢄ
ꢊꢀꢄꢀ
ꢀꢉꢍ
ꢊꢀꢄꢉ
ꢀꢉꢉ
ꢎꢑꢁꢖ
ꢕꢀꢉꢁ
ꢚꢁ
ꢀꢄꢉ
ꢀꢉꢉ
ꢐ
ꢀꢂꢋ
ꢁꢁꢉꢒꢀꢅ
ꢀꢅꢋ
ꢃꢌꢂ
ꢀꢌꢉ
ꢀꢉꢉꢒꢁꢄ
ꢐ
ꢐ
ꢐ
ꢊꢀꢄꢁ
ꢃꢌꢍ
ꢈ
ꢄ
ꢄ
ꢊꢀꢄꢃ
ꢛ
ꢛ
ꢜ
ꢀꢉꢍ
ꢈꢀꢀꢁ
ꢔꢕꢃꢀꢃꢎ
ꢀꢄꢃ
ꢀꢉꢒꢄꢉ
ꢌ
ꢀꢅꢃ
ꢂꢂꢁ
ꢝꢀꢉꢌꢇ
ꢃꢄꢄꢎ
ꢐ
ꢐ
ꢐ
ꢀꢃꢉ
ꢀꢉꢒꢄꢉ
ꢊꢀꢎꢀ
ꢂꢂꢉ
ꢊꢀꢋꢀ
ꢃꢑꢌ
ꢝꢀꢉꢅꢇ
ꢁꢉꢅꢎ
ꢕꢀꢀꢉ
ꢚꢄ
ꢌ
ꢓꢀꢁꢁ
ꢃꢁꢌꢎ
ꢀꢄꢀ
ꢁꢁꢉꢒꢀꢅ
ꢊꢀꢄꢂ
ꢃꢌꢍ
ꢈꢀꢀꢃ
ꢔꢕꢃꢀꢃꢎ
ꢕꢀꢉꢂ
ꢄ
ꢊꢀꢃꢌ
ꢃꢌꢍ
ꢊꢀꢅꢌ
ꢃꢌꢍ
ꢐ
ꢐ
ꢐ
ꢅ
ꢐ
ꢊꢀꢅꢎ
ꢊꢀꢎꢉ
ꢀꢉꢍ
ꢊꢀꢎꢁ
ꢂꢂꢉ
ꢅ
ꢜ
ꢊꢀꢅꢅ
ꢀꢍ
ꢀꢂꢎ
ꢀꢉꢒꢄꢉ
ꢂꢂꢍ
ꢀꢄꢂ
ꢁꢁꢉ
ꢀꢅꢂ
ꢀꢉꢒꢄꢉ
ꢇ
ꢇ
ꢈꢅꢅꢋ
ꢊꢀꢄꢄ
ꢄꢅꢍ
ꢐ
ꢐ
ꢓꢀꢁꢉ
ꢖꢊꢀꢉꢄ
ꢀꢍ
ꢃꢌꢍ
ꢊꢀꢌꢀ
ꢊꢀꢋꢂ
ꢁꢍꢁ
ꢀꢃꢁ
ꢀꢉꢒꢄꢉ
ꢀꢃꢋ
ꢀꢉꢒꢄꢉ
ꢀꢃꢀ
ꢀꢉ
ꢊꢀꢌꢉ
ꢃꢌꢉ
ꢓꢀꢀꢎ
ꢈꢅꢅꢌ
ꢊꢀꢎꢌ
ꢃꢍꢌ
ꢊꢀꢎꢎ
ꢂꢂꢉ
ꢊꢀꢋꢃ
ꢉꢑꢁꢒꢄ!
ꢀꢉꢍ
ꢀꢅꢌ
ꢊꢀꢄꢅ
ꢀꢍ
ꢊꢁꢉꢃ
ꢂꢂꢍ
ꢊꢁꢀꢂ
ꢁꢍꢁ
ꢊꢀꢎꢄ
ꢁꢍꢁ
ꢊꢀꢌꢁ
ꢊꢀꢌꢂ
ꢀꢉꢍ
ꢈꢀꢀꢂ
ꢔꢕꢃꢀꢃꢎ
ꢂ
ꢁ
ꢓꢀꢀꢌ
ꢀꢎꢀꢄ
ꢛ
ꢜ
ꢀꢃꢎ
ꢀꢉꢒꢄꢉ
ꢊꢀꢅꢂ
ꢝꢀꢉꢅꢆ
ꢀꢄꢁ
ꢁꢁꢒꢁꢄ
ꢓꢀꢀꢅ
ꢀꢎꢀꢄ
ꢀꢉꢒꢄꢉ
ꢀꢃꢃ
ꢀꢒꢄꢉ
ꢊꢀꢅꢋ
ꢂꢂꢍ
ꢁꢍꢁ
ꢊꢀꢎꢅ
ꢁꢁꢉ
ꢊꢁꢀꢉ
ꢀꢃꢄ
ꢀꢉꢉ
ꢀ
ꢁ
ꢂ
ꢊꢁꢉꢂ
ꢉꢑꢁꢒꢄ!
ꢃ
ꢀꢉꢉ
ꢊꢀꢎꢂ
ꢂꢂꢉ
ꢐ
ꢝꢀꢉꢄ
ꢈꢀꢀꢀ
ꢔꢕꢃꢀꢃꢎ
ꢊꢀꢋꢄ
ꢃꢍꢌ
ꢊꢀꢋꢅ
ꢂꢂꢉ
ꢁꢉꢅꢎ
ꢝꢀꢉꢌꢆ
ꢃꢄꢄꢎ
ꢀꢂꢅ
ꢐ
ꢀꢃꢅ
ꢓꢀꢀꢋ
ꢈꢅꢅꢋ
ꢊꢁꢉꢁ
ꢁꢍꢁ
ꢋ
ꢎ
ꢌ
ꢅ
ꢄ
ꢃ
ꢂ
ꢁ
ꢀ
ꢀ
ꢊꢀꢅꢁ
ꢀꢉꢍ
ꢀꢄꢄ
ꢀꢉꢒꢄꢉ
ꢐ
ꢊꢀꢄꢌ
ꢃꢍꢌ
ꢊꢀꢎꢃ
ꢂꢂꢉ
ꢊꢁꢀꢃ
ꢁꢁꢍ
ꢁꢁꢒꢁꢄ
ꢀꢉꢒꢄꢉ
ꢊꢀꢄꢎ
ꢀꢄꢍꢐ
ꢐ
ꢐ
ꢂ
ꢐ
ꢓꢀꢁꢂ
ꢈꢅꢅꢋ
ꢀꢅꢄ
ꢀꢉꢒꢄꢉ
ꢊꢀꢌꢋ
ꢀꢉꢍ
ꢀꢂꢌ
ꢀꢃꢌ
ꢁꢁꢉ
ꢊꢁꢉꢄ
ꢀꢍꢄ
ꢊꢁꢉꢅ
ꢀꢉꢍ
ꢐ
ꢐ
ꢊꢀꢅꢉ
ꢅꢍꢎ
ꢈꢀꢀꢄ
ꢔꢕꢃꢀꢃꢎ
ꢕꢀꢉꢃ
ꢚꢁ ꢀꢉꢒꢄꢉ
ꢊꢁꢉꢀ
ꢃꢑꢌ
ꢃꢁꢌꢎ
ꢓꢀꢁꢄ
ꢈꢀꢀꢋ
ꢊꢀꢄꢋ
ꢀꢄꢍ
ꢐ
ꢐ
ꢐ
ꢈꢀꢁꢁ ꢈꢀꢁꢂ
ꢔꢕꢃꢀꢃꢎ ꢔꢕꢃꢀꢃꢎ
ꢐ
ꢓꢀꢀꢂ
ꢀꢎꢀꢄ
ꢓꢀꢀꢄ
ꢆꢀꢉꢀꢄ
ꢔꢕꢃꢀꢃꢎ
ꢊꢀꢅꢀ
ꢀꢍꢄ
ꢀꢅꢀ
ꢁꢁꢉꢒꢀꢅ
ꢀꢅꢁ
ꢄꢅꢉ
ꢕꢀꢉꢎ
ꢀꢅꢅ
ꢂꢂꢁ
ꢚꢃ
ꢊꢀꢅꢃ
ꢁꢁ
ꢊꢀꢅꢄ
ꢀꢉꢍ
ꢃꢍꢌ
ꢊꢀꢌꢅ
ꢈ
ꢀꢅꢎ
ꢀꢉꢒꢄꢉ
ꢓꢀꢀꢃ
ꢈꢅꢅꢌ
ꢊꢀꢌꢄ
ꢃꢌꢍ
ꢐ
ꢐ
ꢀꢄꢅ
ꢀꢉꢉꢒꢁꢄ
ꢀꢄꢎ
ꢀꢉꢉꢒꢁꢄ
ꢃꢍꢌ
ꢊꢁꢀꢎ
ꢊꢁꢉꢌ
ꢊꢁꢉꢎ
ꢊꢁꢉꢋ
ꢈꢀꢀꢅ
ꢔꢕꢃꢀꢃꢎ
ꢀꢌꢀ
ꢁꢁꢒꢁꢄ
ꢀꢉꢉ
ꢀꢉꢉ
ꢀꢉꢉ
ꢀꢄꢌ
ꢀꢉꢉꢒꢁꢄ
ꢊꢀꢌꢌ
ꢀꢉꢍ
ꢀꢌꢂ
ꢃꢌꢒꢄꢉ
ꢔꢕꢃꢀꢃꢎ
ꢈꢀꢁꢉ
ꢀꢅꢉ
ꢃꢌꢒꢁꢄ
ꢀꢌꢁ
ꢃꢌꢒꢄꢉ
ꢈꢀꢁꢀ
ꢔꢕꢃꢀꢃꢎ
ꢊꢀꢌꢎ
ꢀꢉꢉꢍ
ꢀꢄꢋ
ꢀꢉꢉꢒꢁꢄ
ꢐ
ꢐ
ꢐ
ꢐ
ꢐ
ꢐ
ꢐ
ꢐ
ꢐ
ꢐ
ꢈꢀꢀꢌ
ꢔꢕꢃꢀꢃꢎ
ꢆ
ꢆ
ꢕꢀꢉꢌ
ꢚꢁ
ꢍꢆꢁꢁꢎꢃ
ꢐ
ꢚ"&7,
/"8,
ꢀꢁꢂꢃꢁꢄꢅꢀꢆ
ꢊ,-"."$#
ꢊ+ꢖꢜꢆ
ꢜꢅꢉ6ꢆ
ꢀꢁꢂꢃꢄꢅꢆꢇ
ꢜꢅꢉ6ꢆ
ꢈ
ꢀꢁꢂꢃꢄꢅꢆꢆ
ꢈ2&,5ꢐꢐꢐꢐꢐꢐꢐꢐꢐꢐꢐ
6"7,5ꢐꢐꢐꢐꢐꢐꢐꢐꢐꢐꢐꢐ ꢜꢂꢉ6ꢆꢜꢁ
/),,&ꢐꢐꢐꢐꢐꢐꢁꢐꢐꢐꢐꢐꢐ$0
ꢈ123#ꢐꢇ45 (ꢇ
ꢁ
Download from Www.Somanuals.com. All Manuals Seꢃarch And Download.
ꢀ
ꢁ
ꢂ
ꢄ
ꢅ
|