HT-7246IHR
540 Line Color Dome Camera
Intensifier Series
Wall & Ceiling Mountable
200 New Highway
Amityville, NY 11701
631-957-8700
Please read this manual thoroughly before operation and keep
it handy for further reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONS
™
PACKAGE CONTENTS
™
™
THIS DOME CAMERA SHOULD BE ONLY INSTALLED BY
QUALIFIED PERSONNEL
Please make sure that the following items are included
in the package:
TO PREVENT A FIRE OR ELECTRICAL HAZARD PLEASE
USE PROER POWER CABLE THE DOME COVER SHOULD
BE TREATED WITH CARE
1 HT-7246IHR Camera
4 Mounting Screws
™
™
DO NOT CELAN THE COVER WITH AN ABRAISIVE
CLEANING MATERIAL - PLEASE USE A SOFT CLOTH OR
TISSUE TO CLEAN THE DOME COVER
1 Chameleon Dome Cover
THERE ARE NO USER-SERVIEABLE PARTS INSIDE.
PLEASE DO NOT DISASSEMBLE THIS CAMERA OTHER
THAN TO MAKE INITIAL ADJUSTMENTS.
Please leave this manual with the end-user for future
reference.
™
™
™
™
PLEASE USE A UL APPROVED REGULATED 24 VOLT AC
OR 12 VOLT DC POWER SUPPLY
PLEASE USE APPROPRIATE LOW VOLTAGE POWER
CABLE TO PREVENT FIRE OR ELECTRICAL SHOCK.
PLEASE INSURE THAT YOUR INSTALLATION AREA CAN
SUPPORT THE WEIGHT OF THE CAMERA.
PLEASE HANDLE THIS CAMERA CAREFULLY:
- DON’T USE A STRONG OR ABRASIVE DETERGENT WHEN
CLEANING THE CAMERA.
- DON’T EXPOSE THE CAMERA TO DIRECT SUN
3
4
Download from Www.Somanuals.com. All Manuals Search And Download.
CAMERA INSTALLATION
CHAMELEON DOME INSTALLATION
4.
If you wish to change the color of the HT-7246IHR,
place the Chameleon Dome over the camera
Connections:
1. When using 12-Volts DC (constant voltage 600mA)
-CONNECT POWER TO THE POWER JACK.
POWER INPUT:RED
connect
CENTER:(+)
2. When using 24-Volts AC (40 VA)
-CONNECT ACCESSORY CABLE TO THE POWER JACK AND
CONNECT 24V AC TO THE LEAD.
PO WER INPUT:RED
connect
AC 24V
C ENTER:(+)
Place the Chameleon Dome over the HT-7246IHR and push until
It snaps into position.
3. CONNECT VIDEO CABLE
-CONNECT BNC CABLE TO THE BNC JACK.
● Notes : Optional painting before installation
YELLOW:VIDEO OUT
* Painting method for the Chameleon Dome
* Spray the color of your choice onto the Chameleon cover
* If necessary, apply a second coat
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
INTERNAL COMPONENTS
2. Joy Stick
1. Mechanical
(2) JOY STICK
UP
SET BY JOY STICK
RIGHT
LEFT
(1) DC Auto iris
2.8~11mm Lens
DOWN
(1) DC AUTO-IRIS LENS
Adjust between TÅÆW (TELE ÅÆ WIDE) to set the
angle (focal length) Set the focus by adjusting 쏒N
NOTE: BOTH OF THE ABOVE ADJUSTMENTS GET LOCKED
INTO POSITION THROUGH THE USE OF "LOCKING HANDLES".
(2) JOY STICK
TO SET THE OSD (ON SCREEN DISPLAY) , PRESS THE JOY
STICK FOR ONE SECOND AND SET AS DESCRIBED
IN THE MANUAL
7
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
♣ SLC
♣ OSD (ON SCREEN DISPLAY)
All camera functions are menu driven for easy use.
When the image is in front of strong background lighting,
your camera allows you to get a properly balanced image.
♣ INTENSIFIER
♣ Dynamic Noise Reduction
1/3 inch high density CCD and digital processor permit
high quality pictures to be captured in very low light
conditions.
The Intensifier camera has a DSP chip that can
remove image noise efficiently showing clean
images in low light conditions.
♣ High Resolution
♣ ELECTRONIC DAY / NIGHT
Horizontal resolution of 540 TV lines is
The Intensifier camera can show color pictures in all lighting
conditions, or you can have it automatically switch to a B/W
picture in low light conditions
achieved by using a SONY Double Speed CCD with
410,000 pixels, yielding pictures with a high S/N ratio.
♣ Motion Detection
♣ MANUAL / AUTO IRIS LENS
The Intensifier camera will work with auto iris,manual iris and
fixed iris lenses.
Built in motion detector with adjustable areas of coverage will
flash a warning on the screen when motion is detected.
9
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating your camera
◈OSD Menu Setting
◈OSD Function
LENS OPTION
●DC ●MANUAL
SHUTTER
UP
SET BY JOY STICK
RIGHT
●OFF
●F/L ●MANUAL
WHITE BALANCE
●ATW ●AWC MANUAL●
LEFT
SLC – ( Speco Light Compensation )
●OFF ●LOW ●MIDDLE ●HIGH
DOWN
Auto Gain
●OFF ●LOW ●MIDDLE ●HIGH
SET UP MENU
REDUCE NOISE
●OFF ●LOW ●MIDDLE ●HIGH
INTENSIFIER
●AUTO
●OFF
™
Push the Joy stick for one second, and the OSD appears
on the screen. Move the Joy Stick up, down, left & right to
control the OSD functions.
NEXT PAGE
●CAMERA TITEL ●DAY/NIGHT ●SYNC
●MOTION ●PRIVACY ●REVERSE
●DETAIL ●DEFAULT ●PAGE 1
EXIT
11
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating your camera - LENS
Operating your camera - SET UP
1. Press the SET button (JOYSTICK) to access the SETUP mode.
1) Setting up the LENS
●SETUP menu is displayed on the monitor screen.
Select the lens pressing the RIGHT button.
① On the SETUP menu screen, move the arrow indicator to the lens
using the UP or DOWN button.
② Select the desired feature using the LEFT or RIGHT button.
2. Select the desired feature using the UP or DOWN button.
●Each time you press the UP or DOWN button, the arrow
indicator moves up or down.
●Move the arrow indicator to the desired feature item.
3. Change the status of the selected feature using the LEFT
or RIGHT button.
4. When completed, move the arrow indicator to ‘EXIT’ and press
the SET button.
Notes
•
•
●You can access the sub-menu by using the SET button.
●For the mode with ’---’, you may not access submenu.
13
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating your camera – SHUTTER SPEED CONTROL①
2) Shutter status and speed control
You can control brightness of the screen by the shutter speed.
① Press the SET button to display the setup menu and move the arrow
indicator to ‘SHUTTER’ using the UP or DOWN button.
② Set ‘SHUTTER’ to the desired mode using the LEFT or RIGHT
button.
▶OFF : Deactivation
▶When DC LENS is selected, press the SET button To
control the BRIGHTNESS.
Notes
▶FLK (1/100) : Flicker mode
●AUOT IRIS LENS (DC TYPE) is recommended
15
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating your camera –SHUTTER SPEED CONTROL ②
▶MANUAL : When setting the shutter speed manually,
▶ELC : You can control the BRIGHTNESS.
You can select a speed from ‘1/60’ to ‘1/200,000’sec
③ When completed, press ‘SET’
Notes
●Avoid pointing the camera directly at a fluorescent lamp.
●When the SHUTTER menu is set to FLK mode, the INTENSIFIER
will not work.
17
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating your camera - BACKLIGHT
3) SLC (Speco Light Compensation) – BLC/WDR
4) AUTO GAIN (AGC)
A built-in SR chip provides intelligent light level control to overcome
severe Backlight conditions.
AGC allows a brighter picture in low light conditions. Higher GAIN level
will yield a brighter screen, but you might notice an increase in noise.
① Press the SET button to display the SETUP menu and move the arrow
indicator to ‘AGC’ using the UP or DOWN button.
① Press the SET button to display the SETUP menu and move the
arrow indicator to ‘SLC’ using the UP or DOWN button.
② SET ‘SLC’ to the desired mode using the LEFT or RIGHT buttons.
② SET ‘AUTO GAIN’ to the desired mode using the LEFT or RIGHT button.
▶OFF
▶LOW
▶MIDDLE
▶HIGH
▶LOW
▶MIDDLE
▶HIGH
▶OFF
19
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating your camera - WHITE BALANCE
5) WHITE BALANCE
▶MANUAL : To fine adjust, select the Manual mode. You can increase
or decrease the red or blue factor while monitoring the difference on
the screen. Set to ‘MANUAL’ mode and press the SET button. Increase
or decrease the value for RED(R-Gain) and BLUE(B-Gain), watching
the color of the picture, and press the SET button when you obtain the
best color.
① Press the SET button to display the SETUP menu and move the
arrow indicator to ‘WHITE BALANCE’ using the UP or DOWN button.
② Set ‘WHITE BAL.’ to the desired mode using LEFT or RIGHT button.
Notes
●Proper White Balance may not be obtained under the following
conditions. In these cases select the AWC mode.
-When the scene contains mostly a high color temperature object, such
as a blue sky or sunset.
-When the scene is dim.
-If your camera faces a fluorescent lamp directly or is installed in an
area with constantly changing illumination.
▶ATW (Auto Tracking White Balance)
: When color temperature is 2400~12000K, select this mode.
(ex. A fluorescent lamp, outdoor). This is the best setting for most conditions
▶AWC (Auto White Balance Control)
: The white balance is automatically adjusted for a specific environment.
In order to obtain the best result, press the set button while the camera
focuses on white paper. If the environment including the light source is
changed, you have to adjust the white balance again.
21
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating your camera - INTENSIFIER
Operating your camera - INTENSIFIER
6) REDUCE NOISE (Dynamic Noise Reduction)
7) INTENSIFIER
DNR reduces the video noise on the screen.
① Press the SET button to display the SETUP menu and move
the arrow to ‘REDUCE NOISE’ using the UP or DOWN button.
② SET ‘REDUCE NOISE’ to the desired mode using the LEFT
or RIGHT button.
Allows you to get clear images under night or low light conditions.
① Press the SET button to display the SETUP menu and move the
arrow indicator to ‘INTENSIFIER’ using the UP or DOWN button.
② SET ‘INTENSIFIER’ to the desired mode using the LEFT or RIGHT
button.
▶OFF : Deactivation
▶LOW : Low reduction of the noise
▶AUTO : When your camera is under night or low-lighting
level, select this mode. This mode allows the
▶MIDDLE : Middle reduction of the noise
camera to switch into B/W in low light conditions.
▶HIGH : High reduction of the noise
▶OFF : Deactivation
Notes
Notes
● If you press the “auto” button in the Intensifier mode you can
Control the amount of intensification from 2X ~ 128X.
● Increasing the amount of Intensification results in brighter pictures
under low light conditions, and may increase image lag.
● Increasing the amount of intensification may cause image noise
which is to be expected as a normal condition..
●If you change the ‘GAIN’ menu from AGC-L to AGC-H, sensitivity is
increased as well as noise on the screen.
●When the “Gain” menu is off, REDUCE NOISE will not work.
23
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating your camera - CAMERA TITLE②
Operating your camera - CAMERA TITLE①
8) NEXT PAGE
③ Press SET button to access the SETUP mode.
④ You can enter up to 15 characters.
① Press the SET button to display the SETUP menu and move the
arrow indicator to ‘NEXT PAGE’ using the UP or DOWN button.
② SET ‘NEXT PAGE’ to the desired mode using the LEFT or RIGHT
button.
a. Move the cursor to character-enter location by using the LEFT
or RIGHT button.
b. Select the desired character by using the UP or DOWN button.
c. Press SET button to confirm the blinking character. The first
character is saved and the cursor in the bottom of the screen
moves to the next position.
d. Repeat above steps until you create the full name you want.
e. Select the position at which the CAMERA TITLE will be located on
the screen.
-Move the cursor to ‘POS’ and press SET button.
-Select the position by using the 4-directional buttons, then press
the SET button to confirm the position.
(1) CAMERA TITLE
f. When completed, move the cursor to ‘END’ and press SET button.
① Press the SET button to display the SETUP menu and move the arrow
indicator to ‘CAMERA TITLE’ using the UP or DOWN button.
② SET ‘ON’ using the LEFT or RIGHT button.
Notes
Notes
● If you make a mistake while entering a name
move the cursor to ‘CLR’, press ‘SET’ button.
After erasing the character from right to left, correct the character
again.
● If the CAMERA TITLE feature is set to ‘OFF’, the name will not
be displayed on the monitor.
25
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating your camera – DAY/NIGHT/SYNC
(3) SYNC : Two SYNCHRONIZATION modes are available - INTERNAL and
EXTERNAL LINE-LOCK.
(2) COLOR : You can choose color and B/W mode electronically.
① Press the SET button to display the setup menu and move the arrow
indicator to ‘COLOR’ using the UP and DOWN button.
① Press the SET button to display the setup menu and move the arrow indicator
to ‘SYNC’ using the UP and DOWN button.
② SET ‘COLOR’ to the desired mode using the LEFT or RIGHT button.
② SET to the desired mode using the LEFT or RIGHT button.
▶COLOR : The camera will always display a color picture
▶AUTO : The camera will switch into the B/W mode under
▶INT : Internal synchronization
low light conditions.
Notes
▶L/L : If you choose ‘L/L’, you can adjust the desired phase.
-Press the SET button.
●OSD Key may not work for 3 seconds when the
COLOR/BW mode is changed.
-You can adjust the desired phase from 0 to 270.
Notes
●When used in 24V AC power the L/L mode can be used.
●In 12V DC, the SYNC menu defaults to ‘Internal.
27
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating your camera – MOTION DETECTION
(4) Whenever your camera detects motion, THE WORDS “motion detected’
will appear on the screen.
① Press the SET button to display the setup menu and move the arrow
indicator to ‘MOTION’ using the UP and DOWN button.
② SET ‘MOTION’ to the desired mode using the LEFT or RIGHT button.
▶OFF : Deactivation
Max.
Min.
▶ON : MOTION. activated
-Press SET button.
-Move the arrow indicator to ‘AREA SET’ using UP and
DOWN button, and then press the SET button.
- Set the areas you want to observe.
30
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating your camera - PRIVACY
Operating your camera - REVERSE
(5) PRIVACY : To mask area that you want to be private.
① Press the SET button to display the setup menu and move the arrow
to ‘PRIVACY’ using the UP and DOWN button.
(6) REVERSE
① Press the SET button to display the setup menu and move the
arrow indicator to ‘REVERSE’ using the UP and DOWN button.
② SET ‘REVERSE’ to the desired mode using the LEFT or RIGHT
button.
② SET ‘PRIVACY’ to the desired mode using the LEFT or RIGHT button.
▶OFF : Deactivation
▶ON : Reverse the image RIGHT or LEFT.
▶OFF : Deactivation
▶ON : PRIVACY mode activated
-Press the SET button.
-Move the arrow to the area you want to mask.
-Set ‘ON’ using LEFT or RIGHT button.
-Press the SET button and then set the area’s
bounds as for Motion detection.
32
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating your camera - DETAIL
Operating your camera - RESET/RETURN
(7) DETAIL
(8) DEFAULT : Use to reset your camera to FACTORY DEFAULT
SETTINGS.
① Press the SET button to display the setup menu and move the arrow
indicator to ‘DETAIL’ using the UP and DOWN button.
(9) PAGE 1 : Save the setting of NEXT PAGE function, and then
move to SET UP menu.
② SET ‘DETAIL’ to the desired mode using the LEFT or RIGHT button.
▶OFF : Deactivation
▶ON : DETAIL control mode (level 0~31)
When the level is up, the sharpness will increase.
Control this level to get your best picture quality.
If the level is too high, you can get an unnatural image
with video noise.
34
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If you have trouble operating your camera, refer to the following.
Problem
Solution
Problem
Solution
The color of the
picture is not
matched.
●Check that you have properly set the ‘WHITE
BALANCE’ menu
Nothing appears on
the screen.
●Check that the power cord and line connection
between the camera and monitor are proper.
●Check that you have properly connected VIDEO
cable the camera VIDEO output jack.
The image on the
screen flickers.
●Is the camera facing to direct sunlight or
fluorescent lighting? Change the camera position.
The image on the
screen is dim.
●Is lens stained with dirt? Clean your lens with a soft,
clean cloth.
L/L mode cannot
be selected.
●Have you connected your camera to DC power
source? Connect it to an AC power source.
●Set the monitor for the proper condition.
●If the camera is exposed to too strong light
change the camera position.
●Adjust the lens’ focus properly.
The image on the
screen is dark.
●Adjust the contrast feature of the monitor.
●If you have an intermediate device, set the
75Ω/Hi-z properly.
The camera is not
working properly.
●Check that you have properly connected
the camera to an appropriate power source.
MOTION DETECTION
function is not active.
●Have you set ‘MOTION DET.’ menu to off?
●Have you set ‘MD LEVEL’ to too low?
●Have you set ‘MD ARAEA’ properly
36
35
Download from Www.Somanuals.com. All Manuals Search And Download.
DIMENSIONS
SPECIFICATIONS
ITEM
HT-7246IHR
* SIDE VIEW
Power Source
12VDC & 24VAC ( Dual Voltage )
230mA (DC) / 3.8W (AC)
Power Consumption
I mage Sensor
1/3” SONY SUPER HAD CCD, 410,000 pixels
811(H) x 508(V) , 1/3” CCD
Total Pixels
Effective Pixels
LENS Type
768(H) x 494(V) , 1/3” CCD
DC AUTO IRIS VARIFOCAL 2.8~11mm
1 : 1.3 ~2.0
Maximum Aperture Ratio
Scanning System
2 : 1 Interlaced 525 Lines / 60 Fields / 30 Frames
Synchronization
Internal / Line Lock selectable
1.0V [p-p] NTSC Composite, 75Ω / BNC Connector
540 TV Lines
Video Output
Resolution
Gain Control
AGC-L, AGC-M, AGC-H, OFF selectable
1/60 ~ 1/200,000 sec
* TOP VIEW
Electric Shutter Speed
INTENSIFIER
Built-in ( selectable limit ~ X128)
W-ATW / S-ATW / AWC / MANUAL
0.002Lux (intensifier) 0.3Lux(shutter)
50dB (Weight On)
WHITE BALANCE
Min. Illumination
S/N ( Y signal)
REDUCE NOISE
Motion Detection
On Screen Display ( O.S.D )
PRIVACY Function
Operational Temperature
Operational Humidity
ON / LOW / MIDDLE / HIGH
MD1 / MD2 / OFF
Built - in
ON / OFF (4 Programmable Zone)
-29℃ ~ +50℃ (-20℉ ~122℉)
30% ~90% RH
38
27
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
39
Download from Www.Somanuals.com. All Manuals Search And Download.
|