In-Ground Basketball System
Owners Manual
Customer Service Center
• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.
Write Model Number
From Box Here:
REQUIRED TOOLS AND MATERIALS:
WARNING!
• 3 Capable Adults
• (2) Stepladders 8 ft. (2.4 m)
•
• Carpenter’s Level
• 15’ Tape Measure
• Safety Goggles
• Container to Mix
• (2 each) Wrenches and/or Socket Wrenches and
Sockets (Deep-Well Sockets are Recommended).
READ AND UNDERSTAND
OPERATOR'S MANUAL
BEFORE USING THIS UNIT.
• Shovel & Post Hole
Digger
3/8"
1/2"
9/16"
3/4"
15/16"
• Optional: Large &
Small Adjustable
Wrenches
FAILURE TO FOLLOW
OPERATING INSTRUCTIONS
COULD RESULT IN INJURY
OR DAMAGE TO
• Phillips Screwdriver
• (1) Utility Knife
3/8"
1/2"
9/16"
3/4"
15/16"
PROPERTY.
Toll-Free Customer Service Number for U.S: 1-800-558-5234 Canada Only: 1-800-284-8339
© COPYRIGHT 2006 by SPALDING
07/06
ID# M8809511
1
Download from Www.Somanuals.com. All Manuals Search And Download.
1.
Ensure ground is level with playing
surface, then dig pole hole.
PLAYING
SURFACE
WARNING!
24" (61 cm)
36" (91.4 cm)
GROUND
SURFACE
CONTACT UTILITIES
BEFORE DIGGING.
2.
Install nut (2) to J-bolt (1) as
shown. Repeat procedure for
other three J-bolts (1).
2
2-1/2”
(6.35 cm)
3
2
IMPORTANT!
Make sure nuts are 2-1/2”
(6.35cm) from top of
J-Bolts.
1
2
NOTE:
Make sure J-bolts (1) are
in the illustrated position.
1
3.
Install threaded ends of J-bolts (1) through holes in
mounting plate (3) and secure as shown.
NOTE:
Nuts on the top of plate are
used for leveling the pole after
system is fully assembled.
07/06
ID# M8809511
3
Download from Www.Somanuals.com. All Manuals Search And Download.
4.
Fill hole with concrete. Tamp down concrete to release air
pockets and build drainage hill.
5.
Insert J-bolts (1) from mounting plate (3) into cement as shown.
Move assembly around to release any air pockets in cement,
then rest mounting plate on cement drainage hill. Apply some
pressure to level mounting plate on top of drainage hill. Level
mounting plate and square with playing surface. Clean off any
excess cement on mounting plate at this time.
IMPORTANT!
PLAYING SURFACE
Front of mounting plate (3)
must be parallel with
playing surface.
3
WARNING!
DO NOT PROCEED UNTIL
CONCRETE HAS CURED! A
MINIMUM OF 72 HOURS. ALLOW
ADDITIONAL TIME FOR COLD,
WET OR HUMID WEATHER.
1
IMPORTANT!
Check leveling of mounting
plate several times with
carpenter’s level while
concrete is curing.
ID# M8809511
07/06
4
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING!
THREE PEOPLE REQUIRED
FOR THIS PROCEDURE.
FAILURE TO FOLLOW THIS
WARNING COULD RESULT
IN SERIOUS INJURY
5
AND/OR PROPERTY
DAMAGE.
6.
Upright pole (5). Assemble lower pole flange
onto protruding J-bolts (1) as shown. The flange
will then rest on the nuts (2).
IMPORTANT!
Holes in pole must be
parallel with playing
surface.
PLAYING SURFACE
7.
Secure pole (5) flange to mounting plate (3)
as shown. Tighten completely.
NOTE:
Position crank jack
mounting as shown.
5
2
6
2
6
2
6
2
6
6
6
1
PLA
SURF
6
YIN
6
A
C
E
G
1
3
07/06
ID# M8809511
5
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Beginning with upper support arm (8) secure support
arms to pole. Continue by securing lower support
arm (9) as shown.
WARNING!
THREE PEOPLE REQUIRED
FOR THIS PROCEDURE.
FAILURE TO FOLLOW THIS
WARNING COULD RESULT
IN SERIOUS INJURY
AND/OR PROPERTY
DAMAGE.
IMPORTANT!
Do Not Over Tighten.
27
27
27
27
14
27
13
8
13
27
12
27
27
27
27
9
13
14
27
27
7
13
12
12
7
14
27
ID# M8809511
07/06
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Secure backboard to support arms (8 and 9) as shown.
9.
Use same hardware combination for attaching both elevator tubes to the
backoard.
IMPORTANT!
Do Not Over Tighten.
14
27
27
13
8
10
27
13
9
27
07/06
ID# M8809511
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Secure jack brackets (21) to to mounting bracket as shown.
10.
14
13
13
11
21
21
20
YING
E
PLA
C
A
REAR VIEW
SURF
11.
NOTE:
Position U-joint of crank jack (20)
as shown. Where tubes on crank
jack join, hold steady to keep both
tubes from rotating. Rotate handle
clockwise on crank jack to the
fully extended position.
IMPORTANT!
Hold Here.
ID# M8809511
07/06
8
Download from Www.Somanuals.com. All Manuals Search And Download.
A. Replace spacer in jack (20) with spacer (4). Insert through top of
screw jack (20) as shown.
12.
A.
WARNING!
B. Install crank jack (20) U-joint to lower support arm (9) as shown.
TWO PEOPLE REQUIRED FOR
THIS PROCEDURE. FAILURE TO
FOLLOW THIS WARNING COULD
RESULT IN SERIOUS INJURY
AND/OR PROPERTY DAMAGE.
20
4
20
9
20
B.
27
27
14
9
27
12
27
13
27
13
REAR VIEW
20
IMPORTANT!
Do Not Over Tighten.
07/06
ID# M8809511
9
Download from Www.Somanuals.com. All Manuals Search And Download.
13.
Rotate jack handle until jack (20) aligns with jack brackets (21). Secure crank jack (20)
to jack brackets (21) as shown.
WARNING!
TWO PEOPLE REQUIRED FOR
THIS PROCEDURE. FAILURE TO
FOLLOW THIS WARNING COULD
RESULT IN SERIOUS INJURY
AND/OR PROPERTY DAMAGE.
20
15
14
15
13
28
21
13
REAR VIEW
NOTE:
Some adjustment will be necessary
to align the lower crank jack and
bushings to jack brackets (21).
ID# M8809511
07/06
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Apply height indicator labels (18 and 19) to height indicators (16).
A.
14.
B. Attach height indicators (16) to lower arm in areas as shown by turning screws (17) into place with a
phillips screwdriver.
Set-up For Right Side
Set-up For Left Side
16
IMPORTANT!
16
Note Orientation of Height
Indicators: 10’ Mark Should
Face Away From Backboard.
10
10
9
7
8
9
8 7
18
10
9
7
8
19
10
9
8 7
16
16
0
17
17
07/06
ID# M8809511
11
Download from Www.Somanuals.com. All Manuals Search And Download.
15.
Install net (30) to rim as shown.
A.
B.
D.
C.
30
30
Attach rim assembly (29). For rim assembly, see
instructions included with rim.
16.
23
29
Rim Assembly
24
25
22
25
26
Remove rim cover
prior to installing rim
assembly to board.
IMPORTANT!
Refer To Instructions
Included With Rim
Hardware For Rim
Assembly.
Carefully cut and peel
protective film away from
board prior to attaching rim.
ID# M8809511
07/06
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Check leveling at this time. Pole (5) should
be level in all directions. After system is
leveled, completely tighten nuts (2) above
pole flange.
17.
5
NOTE:
If adjustment is necessary, adjust
system by rotating the nuts (2)
between mounting plate (3) and
pole flange.
2
Apply height adjustment label (31) to
front of pole as shown.
18.
REGULATION
RIM HEIGHT IS
10 FEET (3.05 m).
31
07/06
ID# M8809511
13
Download from Www.Somanuals.com. All Manuals Search And Download.
32
Secure pole pad (32) as
shown.
19.
NOTE:
Pole pad may NOT be
included in this model.
Height Adjustment
20.
Rotate crank handle to raise or lower backboard.
NOTE:
If height adjustment is difficult to
operate, you may have over
tightened the areas indicated.
ID# M8809511
07/06
14
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
Item Qty. Part No. Description
Item Qty. Part No. Description
1
2
4
200573 J-Bolt, 1/2-13 x 24” Long
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
1
1
1
2
4
2
2
6
204739 Label, Height Indicator, Right
204740 Label, Height Indicator, Left
222880 Crank, Jack
12 265575 Nut, Hex, 5/8-11
3
1
1
1
8
2
1
1
4
2
4
900661 Anchor Plate
4
205714 Spacer, 0.53 I.D. x 1 O.D. x 5” Long
908284 Pole
908292 Bracket, Crank Jack Support
205702 Nut, Hex, 3/8-16
5
6
200704 Washer, 5/8” x 1.5 O.D.
205125 Spacer, 0.53 I.D. x 0.75 O.D. x 1.88” Long
908282 Support Arm, Upper
205701 Bolt, Carriage, 3/8-16 x 3.5” Long
205700 Bolt, Hex, Tap, 3/8-16 x 3.5” Long
203309 Washer, Flat, 3/8”
7
8
9
908283 Support Arm, Lower
4* 203300 Washer, 3/8 Locking,
28 204670A Bushing, Plastic
10
11
12
13
14
15
16
17
205711 Bolt, Hex Head, 1/2-13 x 2-1/4” Long
205516 Bolt, Hex Head, 1/2-13 x 5.75” Long
224728 Bolt, Hex Head, 1/2-13 x 9.25” Long
1
1
1
1
1
1
205076 Bolt, Hex, 1/2-13 x 5.5” Long
Rim
20 202651 Washer, Flat, 1/2”
11 206340 Lock Nut, Hex 1/2-13
Net
200685 Label, Height Adjustment
216555 Pole Pad, Hydra-Rib (May Not Be Included)
216555S Pole Pad, Spalding (May Not Be Included)
2
2
4
205082 Spacer, 0.53 I.D. x 0.75 O.D. x .38 Long
204735 Height Indicator
204733 Screw, #8 x .050” Long
* You May Have Extra Parts With This Model.
HARDWARE IDENTIFIER (BOLTS)
Item #24 (2)
Item #17 (4)
Item #10 (4)
Item #23 (2)
Item #11 (3)
Item #28 (1)
07/06
ID# M8809511
15
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE IDENTIFIER (NUTS, WASHERS & STEEL SPACERS)
Item #4 (1)
Item #6 (8)
Item #22 (4)
Item #26 (4)*
Item #2 (12)
Item #13 (20)
Item #14 (11)
Item #7 (2)
Item #25 (6)
HARDWARE IDENTIFIER (PLASTIC & NYLON SPACERS)
Item #15 (2)
Item #27 (28)
* You May Have Extra Parts With This Model.
ID# M8809511
07/06
16
Download from Www.Somanuals.com. All Manuals Search And Download.
|