Sony Video Game Controller HDCU 950 User Manual

HD CAMERA CONTROL UNIT

HDCU-950

SD ENCODER UNIT

HKCU-951

HD FRAME RATE CONVERTER UNIT

HKCU-953

INSTALLATION AND MAINTENANCE MANUAL

1st Edition (Revised 3)

Serial No. 10001 and Higher : HDCU-950

Serial No. 10001 and Higher : HKCU-951

Serial No. 10001 and Higher : HKCU-953

Download from Www.Somanuals.com. All Manuals Search And Download.

For HDCU-950

Laser Diode Properties

Material

Attention-when the product is installed in Rack:

: In GaAsP

Wave length

Emission duration : Continuous

Laser output power: _8 dBm

: 1310 40 nm

1. Prevention against overloading of branch circuit

When this product is installed in a rack and is

supplied power from an outlet on the rack, please

make sure that the rack does not overload the supply

circuit.

For HDCU-950

2. Providing protective earth

When this product is installed in a rack and is

supplied power from an outlet on the rack, please

confirm that the outlet is provided with a suitable

protective earth connection.

CLASS 1

LASER PRODUCT

LASER KLASSE 1

PRODUKT

3. Internal air ambient temperature of the rack

When this product is installed in a rack, please make

sure that the internal air ambient temperature of the

rack is within the specified limit of this product.

This HD camera control unit is classified as a CLASS 1

LASER PRODUCT.

The CLASS 1 LASER PRODUCT label is located on the

left side panel.

4. Prevention against achieving hazardous

condition due to uneven mechanical loading

When this product is installed in a rack, please make

sure that the rack does not achieve hazardous

condition due to uneven mechanical loading.

For HDCU-950

CAUTION

5. Install the equipment while taking the operating

temperature of the equipment into consideration

For the operating temperature of the equipment, refer

to the specifications of the Operation Manual.

Use of controls or adjustments or performance of

procedures other than those specified herein

may result in hazardous radiation exposure.

HDCU-950 IMM

1 (P)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents

Manual Structure

Purpose of this manual ........................................................................................ 3 (E)

Related manuals................................................................................................... 3 (E)

Contents ............................................................................................................... 4 (E)

Trademark............................................................................................................ 4 (E)

1. Installation Overview

1-1. Checking the ROM and Software Version............................................1-1 (E)

1-2. Standard Accessories ............................................................................1-1 (E)

1-3. Power Cord............................................................................................1-2 (E)

1-4. Matching Connectors and Cables..........................................................1-2 (E)

1-4-1. Connector Input/Output Signal ............................................1-2 (E)

1-4-2. Connection Connectors ........................................................1-6 (E)

1-4-3. Note when Connecting CAMERA Connector .....................1-6 (E)

1-5. Circuit Boards Layouts .........................................................................1-7 (E)

1-6. Setting of Switches on Boards ..............................................................1-8 (E)

1-6-1. AT-149 Board ......................................................................1-8 (E)

1-6-2. AU-281 Board (Front Panel)..............................................1-11 (E)

1-6-3. AVP-4 Board......................................................................1-12 (E)

1-6-4. DRX-1 Board .....................................................................1-14 (E)

1-6-5. DTX-1 Board .....................................................................1-16 (E)

1-6-6. RC-91 Board ......................................................................1-18 (E)

1-6-7. EN-145 Board (HKCU-951) ..............................................1-20 (E)

1-6-8. FC-88 Board (HKCU-953) ................................................1-22 (E)

1-7. Functions of Indicators on Boards ......................................................1-23 (E)

1-7-1. AT-149 Board ....................................................................1-23 (E)

1-7-2. AU-281 Board ....................................................................1-23 (E)

1-7-3. AVP-4 Board......................................................................1-24 (E)

1-7-4. DRX-1 Board .....................................................................1-24 (E)

1-7-5. DTX-1 Board .....................................................................1-25 (E)

1-7-6. RC-91 Board ......................................................................1-26 (E)

1-7-7. EN-145 Board (HKCU-951) ..............................................1-26 (E)

1-7-8. FC-88 Board (HKCU-953) ................................................1-27 (E)

1-8. Installing the HKCU-951/953 .............................................................1-27 (E)

1-8-1. Installing the HKCU-951 ...................................................1-27 (E)

1-8-2. Installing the HKCU-953 ...................................................1-29 (E)

1-9. Installing the RM-B750.......................................................................1-31 (E)

1-9-1. Connecting/Disconnecting the Flexible Card Wire ...........1-31 (E)

1-9-2. Installing the RM-B750......................................................1-32 (E)

1-10. Installing in 19-inch Rack ...................................................................1-34 (E)

HDCU-950 IMM

1 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

2. System Setup

2-1. System Connection................................................................................2-1 (E)

2-1-1. Standard System ...................................................................2-2 (E)

2-1-2. Standard HD/SD System ......................................................2-3 (E)

2-1-3. HD/SD Film Like System ....................................................2-4 (E)

2-1-4. Analog NTSC/PAL System .................................................2-5 (E)

2-2. Setting the System Format ....................................................................2-6 (E)

2-2-1. Setting the Multi-Format ......................................................2-6 (E)

2-2-2. Setting the Reference Input ..................................................2-7 (E)

2-3. Audio System ........................................................................................2-8 (E)

2-3-1. Setting the Intercom System ................................................2-8 (E)

2-3-2. Setting the Microphone ......................................................2-10 (E)

2-4. Systems ...............................................................................................2-11 (E)

2-4-1. Setting the Tally System ....................................................2-11 (E)

2-4-2. Setting the Camera Number ...............................................2-12 (E)

2-4-3. Connecting the Control, Intercom and

Tally Audio Signals............................................................2-12 (E)

2-5. Video Signal System ...........................................................................2-14 (E)

2-5-1. Selecting the Input/Output Signal ......................................2-14 (E)

2-5-2. Adjusting the Signal Phase.................................................2-14 (E)

2-5-3. Setting Aspect Ratio Conversion during Down-convert....2-15 (E)

2-5-4. Level Adjustment of the VBS Signal

(only when HKCU-951 is installed) ..................................2-17 (E)

2-5-5. Adjusting the Level of Signals for Waveform Monitor .....2-18 (E)

2-5-6. Adjusting the Level of Signals for Picture Monitor ...........2-21 (E)

2-5-7. Setting the RET Input.........................................................2-22 (E)

2-6. Note on Using the Large Lens Adapter CA-905L ..............................2-26 (E)

3. Service Overview

3-1. Cleaning of Connector/Cable ................................................................3-1 (E)

3-2. Recommended Replacement Parts ........................................................3-2 (E)

3-2-1. Power Fan.............................................................................3-2 (E)

3-3. Character Display Function...................................................................3-3 (E)

HDCU-950 IMM

2 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual Structure

Purpose of this manual

This manual is the installation and maintenance manual of the following models :

HD Camera Control Unit

SD Encoder Unit

HD Frame Rate Converter Unit

HDCU-950

HKCU-951

HKCU-953

This manual is intended for use by trained system and service engineers, and

describes the information regarding the installation of the unit and the information

required for initial service.

Related manuals

Beside this Installation and Maintenance Manual, the following manuals are avail-

able for the unit.

. Operation Manual (Supplied with HDCU-950)

This manual describes how to operate the HDCU-950.

. Maintenance Manual (Available on request)

This manual intended for use by trained system and service engineers describes

(the circuit overview, the main part replacements, electrical alignment, etc.)

required for parts-level service.

For obtaining, contact your local Sony Sales Office/Service Center.

Part number : 9-967-988-0X

. HDCU-950 e-Manual (Available on request)

This electronic manual intended for use by trained system and service engineers

describes (detailed parts list, block diagrams, schematic diagrams, and board

layouts.) required for parts-level service.

For obtaining, contact your local Sony Sales Office/Service Center.

. “Semiconductor Pin Assignments” CD-ROM (Available on request)

This “Semiconductor Pin Assignments” CD-ROM allows you to search for

semiconductors used in B&P Company equipment.

Semiconductors that cannot be searched for on this CD-ROM are listed in the

maintenance manual for the corresponding unit. The maintenance manual contains

a complete list of all semiconductors and their ID Nos., and thus should be used

together with the CD-ROM.

Part number: 9-968-546-XX

HDCU-950 IMM

3 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

Contents

The following is a summary of the sections of this manual.

Section 1 Installation Overview

Describes how to checking the ROM version, connectors and cables, setting of

switches on boards, function of the indicators on boards, installing in 19-inch rack,

etc.

Section 2 System Setup

Describes how to set and adjust when connecting the unit to the camera system.

Section 3 Service Overview

Describes recommended replacement parts, how to cleaning connector/cables and

charactor display function.

Trademark

Trademark or registered trademark used in this manual is follows.

. Clear-Com is a registered trademark of Clear-Com Intercom Systems.

HDCU-950 IMM

4 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

Section 1

Installation Overview

1-1. Checking the ROM and Software Version

When connecting the following peripheral equipment to the unit, confirm that the versions of the ROMs

and software which are installed in each model. If the version is lower than the following one, the ROM

needs to be replaced and the software needs to be upgraded.

In this case, contact your local Sony Sales Office/Service Center.

ROM

Peripheral equipment

Board

Ref. No.

ROM version

MSU-700A

MSU-750

CPU-293

CPU-286

AT-89 or AT-89A

AT-100

IC5, IC6

IC4, IC5

IC10

Ver. 1.10 or higher

Ver. 3.20 or higher

Ver. 2.80 or higher

Ver. 2.73 or higher

CNU-700

CNU-500

RCP-720/721

RCP-730/731

RCP-740/741

RCP-700/701

MPU-79

IC10

MPU-79

IC10

MPU-92

IC6

Software

Peripheral equipment

Board

Software version

RCP-750/751

RM-B750

MPU-123

MPU-124

AT-130

Ver. 1.01 or higher

Ver. 1.00 or higher

Ver. 1.20 or higher

HDC-950/900

1-2. Standard Accessories

The HDCU-950 and optional boards consist of the following components.

. HDCU-950

HDCU-950 unit

Operation manual

Maintenance manual

4-pin plug connector (M)

Remote indicator assembly

(1)

. HCKU-951

EN-145 board

VDA-61 board

(1)

. HKCU-953

FC-88 board

SDI-73 board

(1)

HDCU-950 IMM

1-1 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-3. Power Cord

1-4. Matching Connectors and Cables

1-3. Power Cord

1-4. Matching Connectors and Cables

1-4-1. Connector Input/Output Signal

BNC Connector

The power cord is not supplied with this unit. Be sure to

use the specified power cord.

Do not use the damaged power cord.

HDCU-950

For U.S.A. and Canada

1 Power cord 125 V 10 A (2.4 m) : ! 1-551-812-11

1125 digital signal

2 Plug holder (black) :

2-990-242-01

RET (1 to 3) IN : BNC

Conforms to BTA-S004B, 1.485 Gbps/1.4835 Gbps

SMPTE 292M

AC inlet

SERIAL OUT (1 to 2, MONI) : BNC

Conforms to BTA-S004B, 0.8 V p-p, 75 Z, 1.485 Gbps/

1.4835 Gbps

SMPTE 292M

For Europe

REFERENCE IN : BNC

1 Power cord 250 V 10 A (2.5 m) : ! 1-782-929-11

0.3 V, ternary SYNC, 75 Z

2 Plug holder (brown) :

3-613-640-01

Or, black burst signal 0.286 V p-p, 75 Z

AC inlet

SD (525/625) digital signal

RET (1 to 3) IN : BNC

Component serial signal : 270 Mbps

SMPTE 259M

SD SDI OUT (1 to 2) : BNC

Component serial signal : 0.8 V p-p, 75 Z, 270 Mbps

SMPTE 259M

For Japan

Specified power cord : DK-2401 or equivalent

1 Power cord set (Approx. 2.4 m)

Analog signal

PIX OUT : BNC

1.0 V p-p, 75 Z

2 Plug holder (brown)

3-613-640-01

3 Conversion adapter 3P-2P ! 1-793-461-11

WF OUT : BNC

To avoid an electric shock, be sure to connect the ground

to earth when the conversion adapter 3P-2P specified in

No. 3 of the above illustration, is used.

1.0 V p-p, 75 Z

SYNC OUT : BNC

0.3 V, ternary SYNC, 75 Z

Or, 0.3 V p-p, SD SYNC, 75 Z selectable

AC inlet

Other

PROMPTER IN : BNC

1.0 V p-p, 75 Z

HDCU-950 IMM

1-2 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-4. Matching Connectors and Cables

CAMERA connector (optical/electrical composite connector)

HKCU-951 (525/625 analog signal)

Y/G OUT : BNC

VIDEO

Y/P^B/P^R

Y : 1.0 V p-p (video: 0.714 V, sync : 0.286 V ), 75 Z

G : 0.7 V, 75 Z

Conforms to BTA-S004B, 1.485 Gbps/

1.4835 Gbps serial

SMPTE 292M

B-Y/B OUT : BNC

RET VIDEO

Y/P^B/P^R

B-Y : 0.756 V p-p, 75 Z (when 75 % color bar is input)

B : 0.7 V, 75 Z

Conforms to BTA-S004B, 1.485 Gbps/

1.4835 Gbps serial

SMPTE 292M

R-Y/R OUT : BNC

R-Y : 0.756 V p-p, 75 Z (when 75 % color bar is input)

R : 0.7 V, 75 Z

INCOM

MIC

DIGITAL AUDIO (AES/EBU)

CAMERA COMMAND

PROMPTER

2ch

VBS OUT : BNC

1.0 V p-p, 75 Z

HKCU-953

1125 digital signal

HD SDI OUT (1 to 2) : BNC

Conforms to BTA-S004B, 0.8 V p-p, 75 Z, 1.485 Gbps/

1.4835 Gbps

SMPTE 292M

Analog signal

FRAME REFERENCE IN : BNC

0.3 V, ternary SYNC, 75 Z

Or, black burst signal 0.286 V p-p, 75 Z

FRAME REFERENCE OUT : BNC

THROUGH OUT/0.3 V p-p, FRAME SYNC pulse, 75 Z

HDCU-950 IMM

1-3 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-4. Matching Connectors and Cables

MIC1/MCI2 (XLR 3-pin, Male)

*1 : CHU MIC 1/2 AMP GAIN

CONT0

CONT1

CONT2

CHU MIC AMP GAIN

60 dB

50 dB

40 dB

30 dB

20 dB

L (H)

H (L)

L (H)

_ EXT VIEW _

(0 dBu = 0.775 Vrms)

The setup for HDCU-700A mode is shown in parenthesis ( ).

In the case of HDCU-700A mode : S423-2/AT-149 → ON

No. Signal

Specifications

MIC OUT (G)

0 dBu/_20 dBu

*2 :

MIC OUT (X)

MIC OUT (Y)

(Selectable with S502,

S503/AVP-4)

8pin

15pin

MIC GAIN CONT

MIC 1 and 2 ON

MIC 1 ON

MIC 2 ON

MIC REMOTE (D-sub 15-pin, Female)

(WF REMOTE (D-sub 15-pin, Female))

INTERNAL set

*3 :

CONT1

CONT2

ASPECT

SQ (16 : 9)

EC (4 : 3)

_ EXT VIEW _

INTERNAL set

LB (4 : 3)

In the case of MIC REMOTE mode : S423-3/AT-149 →

OFF

In the case of WF REMOTE mode : S423-3/AT-149→ ON

No. Signal

Specifications

Recall system

+5.5 V OUT

Max. 250 mA

TALLY GND

GND for TALLY

No.

Signal

Specifications

G TALLY OUT

R TALLY OUT

CHU MIC CONT2

ON (GND) : Max. 30 mA IN

*1 Refer to the right column.

No connection

LOW ACTIVE

AMP

CONT1

GAIN IN

CONT0

RECALL2 (G)

RECALL3 (B)

RECALL1 (R)

RECALL4 (SEQ)

GND

MIC1 GAIN CONT

ON/OFF IN

GND

*2 Refer to the right column.

GND for +5.5 V

TALLY OUT

R/G TALLY OUT

ON (GND) : Max. 30 mA IN

No connection

LOW ACTIVE

ASPECT REMOTE

ON/OFF

L : REMOTE

RECALL5 (ENC)

RECALL6 (R+B)

RECALL7 (R+G)

RECALL8 (G+B)

ASPECT CONT1

*3 Refer to the right column.

CTL

CONT2

MIC2 GAIN CONT

ON/OFF IN

*2 Refer to the right column.

HDCU-950 IMM

1-4 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-4. Matching Connectors and Cables

INCOM/TALLY/PGM (D-sub 25-pin, Female)

WF MODE (4-pin, Female)

_ EXT VIEW _

No.

Signal

Specifications

(0 dBu = 0.775 Vrms)

SEQ CONT OUT (G)

OPEN COLLECTOR

+(PNP)/_(NPN)

No.

Signal

Specifications

ENG (R) (X) OUT

ENG (R) (Y) OUT

ENG (G)

ENG SYSTEM RECEIVE

0 dBu BALANCED

GND for ENG

SEQ CONT OUT (X)

(Selectable with S301/RC-91)

STAIR CASE OUT (X) *4

STAIR CASE OUT (G) GND for STAIR CASE

ENG (T) (X) IN

ENG (T) (Y) IN

PGM1 (X) IN

PGM1 (Y) IN

PGM1 (G) IN

GND

ENG SYSTEM TALK

0 dBu BALANCED

_20 dBu/0 dBu

*4 : Stair Case signal

(Selectable with

S500/AVP-4)

DC 0 2 V

GND for AUX

AUX3

RCP/CNU (8-pin, Female)

R TALLY (X) IN

R TALLY (Y) IN

GND

ON : 24 Vdc, TTL (H), SHORT

OFF : 0 Vdc, TTL (L), OPEN

CHASSIS GND

PROD (R) (X) OUT

PROD (R) (Y) OUT

PROD (G)

PROD SYSTEM

RECEIVE 0 dBu BALANCED

GND for PROD

_ EXT VIEW _

Specifications

PROD (T) (X) IN

PROD (T) (Y) IN

PGM2 (X) IN

PGM2 (Y) IN

PGM2 (G) IN

AUX4

PROD SYSTEM TALK

0 dBu BALANCED

_20 dBu/0 dBu

No.

Signal

TX (+)

CCU SERIAL DATA

TX (_)

(Selectable with

RX (+)

RCP/CNU/BVP/MSU/

VCS SERIAL DATA

GND for TX

S501/AVP-4)

RX (_)

TX GND

AUX5

POWER (+) OUT

POWER (_) OUT

SPARE

RCP POWER, +30 V

GND for POWER

G TALLY (X) IN

G TALLY (Y) IN

ON : 24 Vdc, TTL (H), SHORT

OFF : 0 Vdc, TTL (L), OPEN

HDCU-950 IMM

1-5 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-4. Matching Connectors and Cables

INCOM (5-pin, Female)

Connector

Connector/cable

HDCU-950

1-569-370-12 PLUG, BNC or

BELDEN8281 Cable or

RET IN (1-3)

SERIAL OUTPUT (1-2, MONI) equivalent

SD SDI OUT (1-3)

_ EXT VIEW _

(0 dBu = 0.775 Vrms)

HKCU-953

HD SDI OUT (1-2)

No.

Signal

Specifications

MIC1/MIC2

1-508-083-00 XLR 3-pin female

INCOM (T) IN (Y)

INCOM (T) IN (X)

_20 dB

(3-pin, Male)

or CANNON XLR-3-11C

equivalent

(CARBON MIC)

_40 dB

MIC REMOTE

1-506-582-11 D-sub 15-pin, male

or JAE DA-CI-J10 equivalent

(ECM MIC)

(WF REMTOE)

(D-sub 15-pin, Female)

INCOM/TALLY/PGM

(D-sub 25-pin, Female)

WF MODE

_60 dB

(DYNAMIC MIC)

GND for INCOM

D-sub 25-pin, male

INCOM (T) IN (G)

INCOM (R) OUT (X)

JAE DA-25PF-N equivalent

1-560-155-00 PLUG, 4-pin male

(supplied)

Max. 12 dBu

No connection

(4-pin, Female)

RCP/CNU

1-766-848-11 PLUG, 8-pin male

or CCA cable assembly (optional)

CCA-5-30 (30 m), CCA-5-10

(10 m), CCA-5-3 (3 m)

1-508-370-11 XLR 5-pin, male

or CANNON XLR-5-12C

equivalent

(8-pin, Female)

1-4-2. Connection Connectors

When connecting cables to each connector of the connec-

tor panel during installation or service, connect the follow-

ing connectors or equivalent to the tip.

INCOM

(5-pin, Female)

Connector

Connector/cable

*1 : Caution in making the optical/electric signal composite cable:

When making the optical/electric signal composite cable used for this

camera system, the connection connectors specified in this manual

must be used in order to comply with the limits for EMC regulations.

HDCU-950

CAMERA

LEMO®

PUW. 3K. 93C. TLCC96 *1

(HDC-900/950/930 side)

CCU

LEMO®

1-4-3. Note when Connecting CAMERA

Connector

FUW. 3K. 93C. TLMC96 *1

1-569-370-12 PLUG, BNC

HDCU-950

Before connecting the unit to the camera adapter, clean the

following optical contact blocks.

REFERENCE IN

PIX OUT

For the cleaning procedure, refer to Section 3-1, “Cleaning

of Connector/Cable”.

WF OUT

SYNC OUT

PROMPTER IN

. CAMERA connector of the unit

. CCU connector of the camera adaptor side

. Optical/electric signal composite cable

HKCU-951

Y/G OUT

B-Y/B OUT

R-Y/R OUT

VBS OUT

HKCU-953

FRAME REFERENCE IN

FRAME REFERENCE OUT

HDCU-950 IMM

1-6 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-5. Circuit Boards Layouts

TX-83 board

CN-2220 board

RX-67board

SDI-70 board

HIF-5 board

CN-2219 board

AU-281 board

VDA-61 board

(HKCU-951) or

DIF-124 board

DIF-124 board or

SDI-73 board (HKCU-953)

CN-2227 board

CN-2226 board

CN-2224 board

AT-149 board

CN-2225 board

MB-951 board

AVP-4 board

EN-145 board (HKCU-951) or

RC-91 board

DTX-1 board

DRX-1 board

RC-91 board or

FC-88 board (HKCU-953)

To install the optional board is required depending on the system to be used. For details, refer to Sections

1-8. “Installing the HKCU-951/953” and 2. “System Setup”.

HDCU-950 IMM

1-7 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-6. Setting of Switches on Boards

1-6-1. AT-149 Board

POWER

S404 S409 S408

/1.001

90H

S403

S406

S407

S410

S402

S416 S412

S417

REFERENCE

REF IN

LOCK

S427

REM

S423 S424

S422 S421

S428

H PHASE

STEP

S405

COARSE

ADV

DELAY

AT-149 board (A side/panel side)

. 404 (MARKER SEL)

Sets the type of the aspect marker.

Do not change the settings of the switches described

“Factory use only” and unused switches.

Setting switches

Aspect marker

4 : 3

. S202

Factory use only

Factory setting : OFF

13 : 9

14 : 9

15 : 9

14.94 : 9

16 : 8.649

16 : 6.75

Not used

. S402 (SKIN GATE LEV)

When S408 on the AT-149 board is set to LOC, adjusts

the zebra level of the skin gate of the MONITOR output

signal.

8 through F

Interlocking aspect ratio of the

down-converter

Factory setting : 8

. S403 (MOD LEVEL)

When S408 on the AT-149 board is set to LOC, this

Factory setting : 8

switch is valid.

. 405 (H PHASE STEP)

When S410 on the AT-149 board is set to ON, adjusts

the aspect modulation level of the MONITOR output

signal.

Performs the coarse adjustment of the H phase when

S427 on the AT-149 board is set to position other than

REM. Perform the fine adjustment using S428 on the

AT-149 board.

Factory setting : 8

. S406 (V PHASE)

Adjusts the vertical phase with regard to the reference

signal in unit of line.

Factory setting : 8

. S407 (CONVERSION DELAY PHASE)

Performs the fine adjustment of the delay amount of the

signal between HD and SD that is set by S417 on the

AT-149, in unit of 1H or 2.2 usec.

HDCU-950 IMM

1-8 (E)

Factory setting : 0

Download from Www.Somanuals.com. All Manuals Search And Download.

1-6. Setting of Switches on Boards

. S408 (MARKER REMOTE/LOCAL SEL)

Selects either the HDCU-950 or the RCP/MSU connect-

ed outside in order to control the aspect marker and skin

gate signal to be inserted in the HD SDI MONITOR

output signal and in the PIX output signal that are output

from the MONI connector on the rear panel.

REM :Control is performed by RCP/MSU etc., con-

nected outside.

. S414 (FIBER/COAX-1/COAX-2 SEL)

When S423-8 on the AT-149 board is set to ON, select

the camera signal reception mode of the HDCU-950.

When S423-8 on the AT-149 board is set to OFF

(factory setting), the signal is connected by the normal

optical/electrical composite cable.

FIBER : Connection by normal optical/electrical

composite cable

COAX-1 :One-way connection using a BNC cable^*1

COAX-2 :Bi-directional connection using two BNC

cables^*2

LOC : Control is performed by the switches (S402,

S403, S409 and S410) on the AT-149 board.

Factory setting : REM

Factory setting : FIBER

. S409 (MARKER)

*1: After receiving the HD-SDI signal output from the camera, the signal

is locked and each signal is output correctly. (RET3 connector is

used for the HD-SDI signal input connector from the camera.)

*2: Connecting the camera equipped with the HD-SDI input/output is

possible using the two BNC cables instead of the optical/electrical

composite cable. Then the normal operation is possible except the

power feeding function. (As to the HD-SDI output signal to the

camera, the output signal from HD SDI MONITOR is used.)

However, this function cannot be used by default at present. If you

want to use this function, consult your local Sony Sales Office/

Service Center.

When S408 on the AT-149 board is set to LOC, this

switch enables selection whether the ASPECT MARK-

ER signal is inserted or not in the HD SDI MONITOR

output signal and in the PIX output signal that are output

from the MONI connector on the rear panel.

ON : Inserted

OFF : Not inserted

Factory setting : OFF

. S416 (REF-10F-BB) (NTSC only)

Sets this switch when the multi frame is going to be

locked using the 10F-BB signal (SMPTE318M) as a

reference signal.

. S410 (MODULAT)

When S408 on the AT-149 board is set to LOC, this

switch enables selection whether the HD SDI MONI-

TOR output signal that is output from the MONI connec-

tor on the rear panel, receives the aspect modulation

processing or not.

ON : Sets the 10F-BB signal as reference.

OFF : When the 10F-BB signal is not input to REFER-

ENCE.

Factory setting : OFF

ON : Processing is ON

OFF : Processing is OFF

Factory setting : OFF

. S417 (CONVERSION DELAY)

Selects delay amount between the HD-SDI output signal

and the SDI signal after the HD-SDI signal is down-

converted.

. S411 (RCP-PORT)

Not used.

90H :

Minimum delay mode equivalent to 90H

lines of HD signal.

Factory setting :

(

indicates the switch lever

position)

1FRAM : Unity phase mode with 1 frame delay

Factory setting : 90H

. S412 (SYNC OUT HD/SD)

. S418 (FIELD FREQUENCY SEL)

. S419 (INTR/PROG/540P SEL)

Selects the type of the SYNC signal to be output from

the SYNC OUT connector on the rear panel.

HD : HD SYNC signal output

SD : SD SYNC signal output

Factory setting : SD

When S420 on the AT-149 board is set to the position

other than REMOTE, sets the conversion format of the

MAIN HD SDI output signal that is output from the HD

SDI OUT1 and 2 connectors on the rear panel.

. S413

Not used.

The MULTIFORMAT setting of the camera side shall

have the same setting too.

Factory setting :

(

indicates the switch lever

position)

HDCU-950 IMM

1-9 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-6. Setting of Switches on Boards

. S423 (CCU MODE SET 1)

Sets the CCU mode.

Factory setting : 60V (S418)

INTR (S419)

Factory setting : All OFF

FORMAT

S420

S418

S419

-1 : Sets the SD signal format when S420 on the AT-149

board is set to position other than REMOTE.

ON : PAL (625/50)

1080/60 (or 59.94) i

1.000

(or 1.001)

60V

INTR

1080/30 (or 29.97) PsF

1.000

(or 1.001)

60V

PROG

OFF : NTSC (525/60)

-2 : The remote control code of MIC GAIN can be

switched to that of the HDCU-700A.

ON : HDCU-700A mode

1080/50i

1.000

50V

48V

INTR

1080/25PsF

PROG

OFF : Standard (default)

1080/24 (or 23.98) PsF

1.000

(or 1.001)

-3 : Selects the function of the MIC REMOTE connector

on the rear panel.

540/60 (or 59.94) PsF

1.000

60V

540P

(or 1.001)

ON : WFM REMOTE CTL

OFF : MIC REMOTE CTL

-4 : Set the switch to OFF. (900)

-5 : Set the switch to OFF. (RCP-POW)

-6 : The PIX select control from the RCP can be disabled.

ON : Enabled

540P and the formats other that what are describe above,

are not supported at present.

OFF : Disabled

. S420 (FRAME FREQ.SELECT)

Select coefficient between x _1.000and x

-7 : Set the switching control of PIX/WFM.

ON : Controllable only from RCP

OFF : Controllable from both MSU and RCP

-8 : Sets the reception mode of the camera HD-SDI

signal using the electrical coaxial cable. Set this

switch to OFF during ordinary operation.

ON : Depending on the setting of S414 on the AF-

149 board.

1.001

depending upon the HD signal frame frequency.

/1.001 :

/1.000 :

_1.001times

1 time

REMOTE : Control is performed by RCP/MSU, etc.,

connected outside.

Factory setting : REMOTE

OFF : Connection by normal optical/electrical

composite cable

. S421 (1-8 CCU No.)

This switch is mainly used to set the CCU numbers when

RCP is connected to the HDCU-950.

Use switches 1 to 8 to set the CCU numbers from 1 to 96

in BCD notation.

. S424-1 to 8

Factory use only

Factory setting : All OFF

Use switches 1 to 4 to set the first digit and use switches

5 to 8 to set the second digit. (“a” to “f” are invalid.)

. S427 (REFERENCE SIGNAL SEL)

Selects the type and phase control methods of the

external sync signal.

OFF ON

First

digit

HD : Sync-locks to the HD reference signal.

(Supports automatically the frame frequency of

the reference signal to be input.)

BB : Sync-locks to the SD reference signal (BB).

(When the HKCU-951 is mounted, VBS OUT is

SC-locked.)

REM :Control is performed by RCP/MSU, etc.,

connected outside.

Factory setting : REM

Second

digit

CCU No.

Factory setting : All OFF

. S422-1 to 5 (CCU MODE SET 2)

Sets the CCU mode.

Set all to OFF during ordinary operation.

Factory setting : All OFF

-6 : (RCP Sim-Cont)

-7 : (P-B CHARA MIX)

-8 : (TRUNK)

. S428 (H PHASE COARSE)

Performs the fine adjustment of the H phase when S427 on

the AT-149 board is set to position other than REM. Perform

the coarse adjustment using S405 on the AT-149 board.

Factory setting : CENTER

HDCU-950 IMM

1-10 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-6. Setting of Switches on Boards

1-6-2. AU-281 Board (Front Panel)

. S4 (TALK GAIN)

Sets the microphone input level according to the type of

headset microphone to be connected to the INCOM

connector on the front panel.

DYNAMIC : When using a dynamic microphone

(_60 dB)

ECM :

When using a electric condenser micro-

phone (_40 dB)

POWER

CAM

CABLE

ALRAM

OPEN

MAIN

CARBON : When using a carbon microphone

SHORT

(_20 dB)

Factory setting : CARBON

INCOM MIC-ON

PROD

PRIV

OFF

S5 (TALK DYNAMIC/ECM MIC UNBALANCE GND)

When the headset microphone to be connected to the

INCOM connector on the front panel is DYNAMIC or

ECM, this switch sets the input level according to the

type (balanced/unbalanced) of the headset microphone.

GND : In case of unbalanced type (upper side)

OPEN : In case of balanced type (lower side)

Factory setting : OPEN

PGM

ENG

AU-281 board (Front panel)

. S1 (POWER)

Turns ON/OFF the main power of this unit.

ON : Power ON

OFF : Power OFF

Factory setting : OFF

. S2 (INCOM SELECT)

Selects the line to which the INCOM connector on the

front panel is connected.

PROD : Producer line

PRIV: Private (When the unit is disconnected from

the producer line or engineer line, only the

intercom between the unit and the camera is

possible.)

ENG : Engineer line

Factory setting : PRIV

. S3 (INCOM MIC)

Performs the switching operations between ON/OFF of

the headset microphone connected to the INCOM

connector on the front panel and receiving audio/PGM

(program audio) of the producer line (or engineer line).

MIC-ON : Turns ON the headset microphone.

MIC-OFF : Turns OFF the headset microphone.

PGM :

The program audio is output to the INCOM

connector on the front panel.

Factory setting : MIC-OFF

Selecting the receiving audio is valid when S11 on the

AVP-4 board is OFF.

HDCU-950 IMM

1-11 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-6. Setting of Switches on Boards

1-6-3. AVP-4 Board

S15

S16

AVP

POWER

INTERCOM

PGM1

MIX

S501

S500

S11

S12

PGM2

PGM1

LEVEL

S14

PGM2

LEVEL

SIDE

TONE

S503

S502

2WIRE CANCEL

PROD

S711

S611

S710

ENG

MIC LEVEL

NORM

S103

S102

S101

S100

S610

MIC1

MIN

NORM

MIC2

MIN

AVP-4 board (A side/panel side)

. S11 (FP INCOM MODE SEP/MIX/OFF)

Selects the receiving audio of the producer line (or

engineer line) and also selects the mix mode of the PGM

(program audio).

Do not change the settings of the switches described

“Factory use only”.

. S1 (FP PGM SEL PGM1/MIX/PGM2)

SEP : The receiving audio and the PGM (program

audio) are output in the right and left channels

separately.

MIX : The receiving audio and the PGM (program

audio) are mixed and output.

Selects the PGM (program audio) that is output to the

INCOM connector on the front panel.

PGM 1 : PGM CH-1

MIX :

PGM CH-1 + PGM CH-2

PGM 2 : PGM CH-2

Factory setting : PGM 1

OFF : Not mixed. (Depends on the setting of S3 on the

AU-281 board.)

. S2 (MIC 1 LEVEL)

There is not the mix mode of the producer line and the

. S3 (MIC 2 LEVEL)

engineer line.

Use these switches to select AMP GAIN of MIC CH-1/

CH-2 of the camera head using this unit. Set GAIN to

either 60 dB (NORMAL), 50 dB, 40 dB, 30 dB or 20 dB

(MIN) according to MIC sensitivity and audio conditions

during shooting.

Factory setting : OFF

. S12 (INPUT INCOM SELECT)

Set this switch to either channel 1 (PROD) or channel 2

(PROD, ENG) according to the intercom system. When

channel 1 is set, PROD is selected regardless of the

setting of the ENG/PROD select switches of the camera

side and the CCU side.

Factory setting : [NORM] (60 dB)

Factory setting : Channel 2

. S14 (PGM INPUT SEL ANA/SDI)

Selects the type of the PGM (program audio).

ANA :Analog system PGM (Input signals to the

INCOM/TALLY/PGM connectors)

SDI : Embedded digital audio of the SDI signal

selected by S605 on the DTX-1 board.

Factory setting : ANA

HDCU-950 IMM

1-12 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-6. Setting of Switches on Boards

. S15 (MIC DELAY)

. S501 (PGM 2 SEL)

This switch is used to match the amount of delay of MIC

and AES/EBU format audio signal with the video signal.

About 5 msec. is delayed per one step.

Example) :7 : 1 FRAME DELAY (30 FRAME/SEC)

8 : 1 FRAME DELAY (25 FRAME/SEC)

Factory setting : 0

Set the input signal level of the PGM (program audio)

CH-2 to either 0 dBu or _20 dBu.

Factory setting : 0 dBu

. 502 (MIC 2 OUT LEVEL)

Set the AUDIO signal level of the MIC-2 connector on

the rear panel to either 0 dBu or _20 dBu.

Factory setting : 0 dBu

. S16-1 to 8

Factory use only

Factory setting : All OFF

. S503 (MIC 1 OUT LEVEL)

Set the AUDIO signal level of the MIC-1 connector on

the rear panel to either 0 dBu or _20 dBu.

Factory setting : 0 dBu

. S100 (R TALLY POWER/CONTACT)

. S102 (R TALLY POWER/TTL)

Set these switches according to the signal standard of the

R TALLY signal to be input in the INCOM/TALLY/

PGM connector on the rear panel. Refer to the following

table for the relation between signals and switch setups.

Factory setting : CONTACT (S100)

. S610 (PROD RTS/CLEAR)

. S611 (PROD INCOM ENG SELECT)

Selects the intercom system of the producer line.

Factory setting : 4W (S611)

TTL (S102)

RTS (S610)

S611

S610

. S101 (G TALLY POWER/CONTACT)

. S103 (G TALLY POWER/TTL)

Set these switches according to the signal standard of the

G TALLY signal to be input in the INCOM/TALLY/

PGM connector on the rear panel. Refer to the following

table for the relation between signals and switch setups.

Factory setting : CONTACT (S101)

4-wire system

RTS system

RTS

Clear-Com system

. S710 (ENG RTS/CLEAR)

. S711 (ENG INCOM ENG SELECT)

TTL (S103)

Selects the intercom system of the engineer line.

Factory setting : 4W (S711)

RTS (S710)

Setting the tally system

Red tally

Green tally

S711

S710

Switch

S100

S102

S101

S103

4-wire system

RTS system

Signal

standard

POWER/

CONTACT TTL

POWER/

CONTACT TTL

POWER/

RTS

Clear-Com system

Contact

supply

CONTACT

POWER

24 V voltage POWER

supply

POWER

TTL

POWER

TTL

5 V voltage POWER

supply

. S500 (PGM 1 SEL)

Set the input signal level of the PGM (program audio)

CH-1 to either 0 dBu or _20 dBu.

Factory setting : 0 dBu

HDCU-950 IMM

1-13 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-6. Setting of Switches on Boards

1-6-4. DRX-1 Board

DRX

POWER

S204

S206

S202

PsF

540P

S201

S205

CHARACTER

REW

S203

DRX-1 board (A side/panel side)

. S205 (CB SEL)

Do not change the settings of the switches described

“Factory use only”.

Selects the color bar signal that is output from the HD

SDI OUT 1 and 2 connectors (of the HDCU-950/HKCU-

953) on the rear panel.

. S201 (GRAY ON/OFF)

Setting switches Color bar

When you turn off the power of the camera or when the

communication with the camera is cut, this switch

selects the signal to be output from the CCU.

ON : Gray signal

OFF : Color bar signal

Factory setting : OFF

16 : 9-100%-CB (non-sprit) BAR

16 : 9-75%-CB (non-sprit)

4 : 3-100CB (non-sprit)

4 : 3-75%-CB (non-sprit)

16 : 9 SMPTE-CB (_I, +Q)

16 : 9 SMPTE-CB (0%)

. S202-1 to 8

Factory use only

Factory setting : All OFF

4 : 3 SMPTE-CB (_I, +Q)

4 : 3 SMPTE-CB (0%)

Multi Format-A ARIB-75%-SMPTE-CB

Multi Format-B ARIB-100%-SMPTE-CB

Multi Format-C ARIB-CB (+I)

Multi Format-C SMPTE-CB (_I, +Q)

. S203 (CHARACTER)

The character page to be mixed into the signal that is

output from the MONI connector on the rear panel, can

be changed with REW/FF.

REW :Returns to previous page.

FF : Goes to next page.

Factory setting : 0

Factory setting : CENTER

. S204

Factory use only

Factory setting : 0

HDCU-950 IMM

1-14 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-6. Setting of Switches on Boards

. S206

Factory setting : All OFF

-1, 2

Factory use only

-3 (MAIN/MONI CHANGE)

When this switch is set to ON, the character signal and

the marker signal are mixed with the all output signals

except the HD-SDI-MONITOR output.

ON : Change mode

OFF : Normal mode

-4 (MONI CHARACTER OFF)

Selects whether the character signal and the marker

signal are mixed or not to the signal to be output from

the MONI connector on the rear panel.

ON : Forced-OFF (Not mixed)

OFF : Normal mode (Mixed)

-5 (GRAY SIGNAL BAR-CHAR ON/OFF)

This switch enables mixing of the color bar character

with the gray signal that is output when camera is turned

off.

ON : GRAY BAR-CHAR ON

OFF : GRAY BAR-CHAR OFF

HDCU-950 IMM

1-15 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-6. Setting of Switches on Boards

1-6-5. DTX-1 Board

DTX

POWER

S607 S608

OPTICAL

CONDITION

CCU

S610

S606

S603

CHU

LOCK

S604

RETURN SET

S601

REM

S605

DTX-1 board (A side/panel side)

S603-1, -3, -5, -7 S603-2, -4, -6, -8

Aspect ratio

Do not change the settings of the switches described

“Factory use only”.

Letter box^*1

Edge-crop^*1

Squeeze^*1

OFF

. S601 (SD RETURN FORMAT)

OFF

It is interlocked with

the down-conversion

aspect ratio of the

RC-91 board output.

Selects the signal format that is input to the RET1 to 3

connectors on the rear panel when S605 on the DTX-1

board is set to SD.

VBS (20) :Analog VBS

SDI (80) : SD SDI (D1)

Factory setting : SDI

*1 : Letter box : The HD video signal of 16 : 9 (or aspect ratio set with

S604 on the DTX-1 board) is inserted in the picture

frame of 4 : 3 as it is and converted to the SD signal.

(The black level is inserted in the top and bottom of the

picture.)

Edge-crop : Video signal as large as 4 : 3 is cut from the HD video

signal and is converted to the SD signal.

Squeeze : The HD video signal of 16 : 9 is converted to the SD

signal as it is.

. S603 (SD RET ASPECT)

This switch is valid when S605 on the DTX-1 board is

set to SD.

Selects the aspect ratio of the SD return signal to be

input to the RET1 to 3 and RET4 (PROMPTER) connec-

tors on the rear panel when S601 on the DTX-1 board is

set to SD.

S603-1, -2 : RET1

S603-3, -4 : RET2

Factory setting : All OFF

. S604 (LB ASPECT)

This switch is valid when S605 on the DTX-1 board is

set to SD.

Select the aspect ratio of the letter box, when S603 on

the DTX-1 board is set to letter box.

S604-1, -2 : RET1

S603-5, -6 : RET3

S603-7, -8 : RET4 (PROMPTER)

S604-3, -4 : RET2

S604-5, -6 : RET3

S604-7, -8 : RET4 (PROMPTER)

S604-1, -3, -5, -7

S604-2, -4, -6, -8

Aspect ratio

13 : 9

14 : 9

15 : 9

16 : 9

OFF

Factory setting : All OFF

HDCU-950 IMM

1-16 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-6. Setting of Switches on Boards

. S605 (RETURN SET)

. S607 (RETURN MODE)

Sets the format of the return signal to be input to the

RET1 to 3 connectors on the rear panel.

HD : Sets the RET1 to 3 to the HD-SDI.

SD : Sets the RET1 to 3 to SD. (Depends on the

setting of S601, S603 and S604 on the DTX-1

board.)

Perform setting of the return signal.

Factory setting : All OFF

-1 (RET-DLY)

Sets the SD return signal and the delay amount of the

phase during up-convert.

ON : Up-convert in the least time

OFF : 1-field delays at maximum.

-2 (RET4-VBS)

REM :Sets the format of each return signal from RM/

MSU, etc. connected outside.

Factory setting : REM

Sets whether the PROMPTER connecter on the rear

panel is used or not as RET4 (VBS input).

ON : Uses it as PROMPTER input.

OFF : Uses it as RETURN4 (VBS input).

-3 to 8

. S606 (RET FC SET)

Sets the frame conversion type of the return signal to be

input to the RET1 to 3 and RET4 (PROMPTER) connec-

tors on the rear panel.

Factory use only

S606-1, -2 : RET1

S606-3, -4 : RET2

. S608-1 to 8

S606-5, -6 : RET3

Factory use only

S606-7, -8 : RET4 (PROMPTER)

Factory setting : All OFF

S606-1, -3,

-5, -7

S606-2, -4,

-6, -8

Type of frame conversion

. S610 (FC SEQUENCE)

Phase at the conversion cycle can be changed during the

frame frequency conversion of the return signal. (Timing

to delete the field can be freely selected during conver-

sion of 60i → 48i and 50i → 48i.)

THROUGH :

Frame conversion is not

performed.

OFF

A (24PsF conversion) :

When the camera side is

24PsF, the forced-reverse

conversion is performed.

(Conversion to reconstruct

24PsF)

Factory setting : 0

OFF

B (48i conversion) :

When the camera side is

24PsF, the forced-reverse

conversion is performed.

(Conversion to 48i format

by simple skipping)

OFF

AUTO :

Depends on the setting of

S1-1 on the FC-88 board.

Factory setting : All OFF

HDCU-950 IMM

1-17 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-6. Setting of Switches on Boards

1-6-6. RC-91 Board

POWER

525

625

REM

LOCAL

S11

S10

CENT

VAR

S301

RIGHT

LEFT

RC-91 board (A side/panel side)

. S6 (ASPECT REMOTE/LOCAL)

Sets whether RCP/MSU connected outside controls or

not the aspect ratio of the SD signal.

REM : Control is performed by RCP/MSU, etc.

connected outside.

Do not change the settings of the switches described

“Factory use only” and unused switches.

. S1 (SET-UP ON/OFF)

Selects whether SETUP is added or not to the VBS

signal to be output from PIX OUT/WF OUT connector

on the rear panel.

LOCAL :Set using the switch on the RC-91 board.

Factory setting : REM

ON : Added

. S7 (ASPECT SEL)

OFF : Not added

Factory setting : OFF

This switch is valid when S6 on the RC-91 board is set

to LOCAL. Selects the aspect ratio to down-convert the

HD signal to SD signal.

. S2, S3, S4

Not used.

SQ (Squeeze) : The HD video signal of 16 : 9 is

output to the SD OUT.

Factory setting :Left side when viewed from the panel

side.

LB (Letter Box) : The picture (13 : 9, 14 : 9, 15 : 9 or

16 : 9) having the aspect ratio

selected by S10-3 and S10-4 on the

RC-91 board is inserted in the

. S5 (CB-SEL)

Selects the color bar signal to be output from the SD SDI

OUT 1 and 2 connectors and the VBS OUT connector

(when the HKCU-951 is installed) on the rear panel.

picture of 4 : 3 as it is, and the signal

is output to the SD OUT.

(Top and bottom are blanked and the

right and left most ends are cut when

the screen is 13 : 9, 14 : 9 or 15 : 9.)

EC (Edge-Crop) : The right and left most ends are cut

and the picture of 4 : 3 aspect ratio is

output to the SD OUT. (Set the

Setting switches

Color bar

100%-CB (non-split)

100% & 75%-CB (non-split)

75%-CB (non-split)

cutting position using S8 on the RC-

91 board.)

Factory setting : SQ

Pseudo SMPTE-CB

Mode to down-convert HD-CB

Not used

5-F

Factory setting : 0

HDCU-950 IMM

1-18 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-6. Setting of Switches on Boards

. S8 (EC POSITION SEL)

-6 (WF-SYNC) :

This switch is valid when S6 on the RC-91 board is set

to LOCAL.

When S7 on the RC-91 board is set to EC or LB, and

S10-3 and S10-4 on the RC-91 board are set to 13 : 9, 14

: 9, or 15 : 9, select the cutting position.

CENT : Cuts out the center.

When mode other than ENC is selected in WF output,

this switch sets whether SYNC is added or not.

-7 (Bar CHARACTER OFF) :

Sets the character with a bar added to the SD signal to

OFF.

ON : Forced-OFF

VAR : Changes the horizontal cutting position with

S9 on the RC-91 board.

OFF : Normal mode

-8 (PIX CHARACTER OFF) :

Factory setting : CENT

Selects whether the character signal is mixed or not to

the signal to be output from the PIX connector on the

rear panel.

. S9 (EC POSITION CONT)

This switch is valid when S6 on the RC-91 board is set

to LOCAL.

ON : Forced-OFF (Not mixed)

OFF : Normal mode (Mixed)

When S8 on the RC-91 board is set to VAR, adjust the

horizontal cutting position.

. S11-1 to 8

Factory use only

Factory setting : All OFF

The cutting position moves left.

The cutting position moves right.

LEFT

RIGHT

. 301 (SEQ CONT POLARITY)

Set this switch according to the used waveform monitor.

+ : PNP open collector output

. S10

Factory setting : All OFF

_ : NPN open collector output

-1 (MONI) :

Factory setting : _

Selects whether the SD SDI OUT2 connector on the rear

panel is set or not as SD SDI MONITOR output.

ON : SD SDI MONITOR

OFF : SD SDI (MAIN)

-2 : Not used.

-3, -4 (LB0/LB1 SEL) :

These switches are valid when S6 on the RC-91 board is

set to LOCAL.

When S7 on the RC-91 board is set to LB, select the

aspect ratio (13 : 9, 14 : 9, 15 : 9 or 16 : 9) of the picture.

S10-3

S10-4

Aspect ratio

OFF

16 : 9

15 : 9

14 : 9

13 : 9

OFF

-5 (MIN-DLY) :

Regardless of the setting of S417 on the AT-149 board,

down-conversion to the SD signal is performed with the

minimum delay.

ON : Minimum delay

OFF : Normal mode (Depends on the setting of S417

on the AT-149 board.)

HDCU-950 IMM

1-19 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-6. Setting of Switches on Boards

1-6-7. EN-145 Board (HKCU-951)

POWER

S402

S401

VBS

S101

S103

S104

LEVEL

SYNC

CHROMA

COMPONENT

S106

S107

S102

R/R-Y

G/Y

S201

B/B-Y

SC PHASE

ADV

S105

DELAY

EN-145 board (A side/panel side)

. S105 (SC PHASE)

Do not change the settings of the switches described

Adjusts the SC phase with regard to the reference signal

“Factory use only” and unused switches.

(BB).

ADV :

Phase advances

. S101 (SD ANA OUT RGB/YCD)

DELAY : Phase delays

Selects the signal that is output from the Y/G, B-Y/B and

R-Y/R connectors on the rear panel.

YCD : Y/B-Y/R-Y

Factory setting : CENTER

. S106-1 to 4

RGB : RGB

Factory use only

Factory setting : RGB

Factory setting : All OFF

. S102

. S107

Not used.

Factory setting : All OFF

Factory setting : A

-1 (ASPECT-F) :

Selects whether the aspect flag is added or not to the

VBS output.

ON : Added (in case if 16 : 9 NTSC)

OFF : Not added

. S103 (SDI A OUTPUT SDI/VBS)

Selects either SDI signal or VBS signal to be output to

the SD SDI OUT1 connector on the rear panel.

SDI : SDI signal

-2 (WIDE-Q FIL) :

VBS : VBS signal

ON : WIDE-Q

Factory setting : SDI

OFF : NARROW-Q

-3 (CHROMA BOOST) :

By setting it to ON, the chroma amount increases by

about 2%.

. S104 (SDI B OUTPUT SDI/VBS)

Selects either SDI signal or VBS signal to be output to

the SD SDI OUT2 connector on the rear panel.

SDI : SDI signal

VBS :VBS signal

Factory setting : SDI

-4 (WFM-VBS) :

The VBS signal that is SC-locked in the EN-145 board

can be output as the VBS (ENC) of the WF output

signal.

ON : VBS (SC-locked by SC-PLL) of the EN-145

board.

OFF : VBS (not SC-locked by SC-PLL) of the RC-91

board.

HDCU-950 IMM

1-20 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-6. Setting of Switches on Boards

. S201

-1, 2 (CB CONT)

Selects the color bar to be output from the ANALOG

COMPOSITE (VBS) generator.

Setting switches

Color bar

S201-1

OFF

SD COMPONENT-CB

SD COMPOSITE-CB

SMPTE-CB

S201-2

OFF

EIAJ/EBU

Factory setting : S201-1 → ON

S201-2 → OFF

-3, 4

Not used.

Factory setting : OFF

. S401 (G/Y SYNC SEL)

Selects whether SYNC is added or not to the G/Y signal

of SD.

ON : Added

OFF : Not added

Factory setting : ON

. S402 (SETUP SEL)

Selects whether SETUP is added or not to the VBS

signal of SD when S427-1 on the AT-149 board is set to

OFF (NTSC).

ON : Added

OFF : Not added

Factory setting: OFF

HDCU-950 IMM

1-21 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-6. Setting of Switches on Boards

1-6-8. FC-88 Board (HKCU-953)

POWER

CONVERT

FRAME

REF IN

LOCK

S3 S2

FC-88 board (A side/panel side)

. S2 (FRAME CONVERT ON/OFF)

When the video format is set to the local setting (S420

on the AT-149 board is set to the mode other than

REMOTE), ON/OFF setting of the FRAME CON-

VERTER function is enabled.

Do not change the settings of the switches described

“Factory use only” and unused switches.

. S1 (MODE SET)

Factory setting : All OFF

-1 (50i → 60i : ENABLE) :

Selects whether 50i → 60i conversion is valid or not.

ON : 50i → 60i is valid.

OFF : Through output without conversion

ON : Turns ON the FRAME CONVERTER function,

and converts the FRAME frequency when the

camera format is set to 24PsF.

When the SD format is set to 525 (NTSC)

(S423-1 on the AT-149 board is set to OFF),

24 PsF → 60i (2 to 3 Pull Down)

-2 (FC-CONV-MODE) :

Selects the conversion mode of the frame conversion.

ON : Frame overlay

OFF : 2 to 3 Pull down

When the SD format is set to 625 (PAL) (S423-

1 on the AT-149 board is set to ON), 24 PsF →

50i

-3 (SUB MODE 1) :

Selects whether the SUB-REFERENCE setting is

detected automatically or not.

ON : Manual setting (Depends on the setting of S1-4

on the FC-88 board)

OFF : Turns OFF the FRAME CONVERTER function

and delays the same signal as the MAIN HD-

SDI output by a few clocks, and outputs it.

Factory setting : OFF

OFF : Automatic detection

. S3

-4 (SUB-REF MODE 2) :

Not used.

When S1-3 on the FC-88 board is set to ON, sets

whether SUB-REFERENCE is connected or not.

ON : SUB-REFERENCE is not available

OFF : SUB-REFERENCE is available

-5 (FC-PHASE ENABLE) :

Factory setting : OFF

. S5 (GEN LOCK)

Selects the FRAME REFERENCE signal to be input.

0 : AUTO

The FC-SDI-OUT phase setting becomes valid with the

HD-SD delay setting.

1 : FRAME REF HD

2 : FRAME REF SD

ON : DRX-SDI-OUT phase adjustment

OFF : FC-SDI-OUT phase adjustment

3 : FRAME REF S. SYNC

Factory setting : 0

. S6-1 to 8

Factory use only

Factory setting : All OFF

HDCU-950 IMM

1-22 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-7. Functions of Indicators on Boards

1-7-1. AT-149 Board

1-7-2. AU-281 Board

POWER

CABLE

ALRAM

CAM

OPEN

MAIN

POWER

D101

D106

D105

SHORT

/1.001

90H

REFERENCE

REF IN

INCOM MIC-ON

OFF

PGM

PROD

PRIV

D107

D108

LOCK

ENG

REM

H PHASE

STEP

COARSE

ADV

DELAY

AU-281 board (panel side)

AT-149 board (A side/panel side)

D3 (green) : MAIN POWER display

Lights up when the power is supplied to the unit correctly.

D101 (green) : Power display

Lights up when the voltage used on this board is normally

supplied.

D4 (green) : CAM POWER display

Lights up when DC180 V power is supplied to the con-

nected camera correctly.

D105 (yellow) : 90H display

Lights up when the delay amount of the SD signal for

downconvert is set to 90H.

D5 (red) : CABLE OPEN display

Lights up when OPEN of the power cable using optical/

electrical composite cable is detected.

Blinks when ALARM (attenuation) of the optical level is

detected.

The delay amount is set with S417 on the AT-149 board.

For details, refer to Section 1-6-1. “Setting of Switches on

Boards _ AT-149 Board”.

D-106 (green) : /1.001 display

Lights up when the SG operation CLOCK frequency is

74.17582 MHz.

Lights up when the frame frequency coefficient of the HD

signal is set to 1/1.001 times.

D6 (red) : CABLE SHORT display

Lights up when short-circuit in the power cable using

optical/electrical composite cable.

The frame frequency coefficient is set with S420 on the

AT-149 board. For details, refer to Section 1-6-1. “Setting

of Switches on Boards _ AT-149 Board”.

D107 (green) : REF IN display

Lights up when the REFERENCE signal is input to the

REFERENCE connector on the rear panel.

D108 (red) : UNLOCK display

Lights up when the unit cannot be synchronized with the

external REFERENCE signal in the external sync mode.

HDCU-950 IMM

1-23 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-7. Functions of Indicators on Boards

1-7-3. AVP-4 Board

D201, D202, D203 (green) : MAIN OUTPUT display

Displays the frame frequency of the MAIN HD SDI output

signal of this unit and camera.

Blinks when the format setting is incorrect.

D201 lights up : Lights up when the frame frequency is 30

Hz (or 29.97 Hz)

D202 lights up : Lights up when the frame frequency is 25

Hz.

DRX

POWER

D201

D202

D203 lights up : Lights up when the frame frequency is 24

Hz (or 23.98 Hz)

The format is set with S418 to S420 on the AT-149 board.

For details, refer to Section 1-6-1. “Setting of Switches on

Boards _ AT-149 Board”.

D203

D204

D205

PsF

540P

CHARACTER

REW

D204 (yellow) : PsF display

Lights up during progressive operation of the camera.

Blinks when the format setting is incorrect.

AVP-4 board (A side/panel side)

The format is set with S418 to S420 on the AT-149 board.

For details, refer to Section 1-6-1. “Setting of Switches on

Boards _ AT-149 Board”.

D1 (green) : POWER display

Lights up when the voltage used on this board is normally

supplied.

D205 (red) : 540P display

Lights up when the connected camera is operated in the

540P mode.

1-7-4. DRX-1 Board

Blinks when the format setting is incorrect.

The format is set with S419 on the AT-149 board. For

details, refer to Section 1-6-1. “Setting of Switches on

Boards _ AT-149 Board”.

DRX

POWER

D201

D202

D203

D204

D205

PsF

540P

CHARACTER

REW

DRX-1 board (A side/panel side)

D2 (green) : POWER display

Lights up when the voltage used on this board is normally

supplied.

HDCU-950 IMM

1-24 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-7. Functions of Indicators on Boards

1-7-5. DTX-1 Board

DTX

POWER

OPTICAL

CONDITION

CCU

D605

D606

D607

CHU

D608

D609

D610

CHU

LOCK

D611

RETURN SET

REM

DTX-1 board (A side/panel side)

D608, D609, D610 : OPTICAL CONDIITON (CHU) display

Displays the optical level received on the camera side.

(0 dBm = 1 mW)

When D607 and D610 light up, be sure to clean the

CAMERA connector of the unit, CCU connector of the

camera side and the optical/electrical composite cable.

When D606 and D609 light up, perform the cleaning as

well. For the cleaning procedure, refer to Section 3-1.

D608 (green) lights up:

Normal (The optical reception level is

D609 (yellow) lights up:

_17 dBm or more.)

Normal (The optical reception level is _17 dBm to _20 dBm)

D610 (red) lights up:

Abnormal (The optical reception level is less than _20 dBm.)

D3 (green) : POWER display

Lights up when the voltage used on this board is normally

supplied.

Attenuates about 0.5 dB by every 1 km of cable.

D605, D606, D607 : OPTICAL CONDIITON (CCU) display

Displays the optical level received on the HDCU-950 side.

(0 dBm = 1 mW)

D605 (green) lights up :

Normal (The optical reception level is _17 dBm or more.)

D606 (yellow) lights up :

Attenuates about 0.5 dB by each relay connector.

D611 (green) : CHU LOCK display

Lights up when communication with the connected camera

is normally established.

Normal (The optical reception level is _17 dBm to _20 dBm)

D607 (red) lights up :

Abnormal (The optical reception level is less than _20 dBm.)

Attenuates about 0.5 dB for every 1 km of cable.

Attenuates about 0.5 dB for each relay connector.

HDCU-950 IMM

1-25 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-7. Functions of Indicators on Boards

1-7-6. RC-91 Board

1-7-7. EN-145 Board (HKCU-951)

POWER

D103

VBS

525

625

LEVEL

SYNC

REM

CHROMA

LOCAL

COMPONENT

R/R-Y

G/Y

CENT

B/B-Y

VAR

SC PHASE

ADV

RIGHT

LEFT

DELAY

RC-91 board (A side/panel side)

EN-145 board (A side/panel side)

D4 (green) : POWER display

Lights up when the voltage used on this board is normally

supplied.

D103 (green) : POWER display

Lights up when the voltage used on this board is normally

supplied.

D3, D5 (green) : MAIN OUTPUT display

Displays the format setting of the SD system.

Blinks when the format setting is incorrect.

D3 (green) lights up :

When the SD system is set to 525/59.94i (NTSC).

D5 (green) lights up :

When the SD system is set to 625/50i (PAL).

For details of the SD system setting, refer to Section 2-2,

“Setting the System Format _ SD system”.

HDCU-950 IMM

1-26 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-7. Functions of Indicators on Boards

1-8. Installing the HKCU-951/953

1-7-8. FC-88 Board (HKCU-953)

1-8. Installing the HKCU-951/953

1-8-1. Installing the HKCU-951

Installation

POWER

D103

D105

Front side (EN-145 board)

1. Turn off the power and disconnect the power cord

from the wall outlet.

CONVERT

2. Loosen the two screws (with drop-safe) and open the

front panel in the direction of the arrow.

FRAME

REF IN

D104

D107

LOCK

Front panel

Screw

(with drop-safe)

FC-88 board (A side/panel side)

D103 (green) : POWER display

Lights up when the voltage used on this board is normally

supplied.

D104 (green) : SUB REF IN display

Lights up when the sub reference for frame lock is input.

Screw (with drop-safe)

D105 (green) : CONVERT display

Lights up when the shooting mode of the camera is set to

24PsF and the 60i or 50i signal is output from the HKCU-

953.

3. Insert the EN-145 board in the right most blank slot.

Check that the EN-145 board is securely connected to

the motherboard (MB-951 board).

D107 (red) : UNLOCK display

Lights up when the frame reference signal is not synchro-

nized with the main reference signal.

EN-145 board

HDCU-950 IMM

1-27 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-8. Installing the HKCU-951/953

Rear side (VDA-61 board)

1. Remove the two screws and remove the blank panel by

holding the handle.

2. Insert the VDA-61 board in the slot.

. Because there is a difference of the depth between

the upper groove and the lower groove, insert the

VDA-61 board in a straight line after inserting it in

the lower groove.

Store the removed blank panel in a safe place.

. Check that the VDA-61 board is securely connected

to the motherboard (MB-951 board).

3. Secure the VDA-61 board with the two screws

removed in step 1.

Upper groove

B3 x 5

Handle

Blank panel

B3 x 5

Lower groove

VDA-61 board

There is a difference of the depth.

HDCU-950 IMM

1-28 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-8. Installing the HKCU-951/953

1-8-2. Installing the HKCU-953

Installation

4. Insert the RC-91 board removed in step 3 in the right

most slot.

Insert the FC-88 board in the second slot from the right

most slot.

Front side (FC-88 board)

1. Turn off the power and disconnect the power cord

from the wall outlet.

Check that the FC-88 and RC-91 boards are securely

connected to the motherboard (MB-951 board).

2. Open the front panel. (Refer to Section 1-8-1, step 2.)

3. Pull up the lever in the direction of arrow A to unlock

and pull out the RC-91 board.

RC-91 board

Levers

FC-88 board

RC-91 board

HDCU-950 IMM

1-29 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-8. Installing the HKCU-951/953

Rear side (SDI-73 board)

1. Remove the two screws and remove the blank panel by

holding the handle.

2. Remove the two screws and remove the DIF-124

board.

3. Insert the DIF-124 board removed in step 2 in the left

most slot.

Insert the SDI-73 board in the second slot from the left

most.

. Because there is a difference of the depth between

the upper groove and the lower groove, insert the

SDI-73 (or DIF-124) board in a straight line after

inserting it in the lower groove.

Store the removed blank panel in a safe place.

. Check that the SDI-73 and DIF-124 boards are

securely connected to the motherboard (MB-951

board).

4. Secure the DIF-124 board with the four screws

removed in steps 1 and 2.

Upper grooves

B3 x 5

Handle

DIF-124 board

SDI-73 board

B3 x 5

Blank panel

B3 x 5

Lower grooves

DIF-124 board

There is a difference of the depth.

B3 x 5

HDCU-950 IMM

1-30 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-9. Installing the RM-B750

1-9-1. Connecting/Disconnecting the

Flexible Card Wire

Contact surface

The flexible card wires are used to connect between the

following boards. Life of flexile card wire will be signifi-

cantly shortened if it is folded. Be very careful not to fold

the flexible card wire.

. One flexible card wire between the AU-281 board (CN2)

of the unit and the VA-211 board (CA2) of the RM-

B750 (when the RM-B750 is installed)

Recessed portion

Connector

. One flexible card wire between the VA-211 board

(CN14) and MPU-124 board (CN104) of the RM-B750

Type A

Removal

Connector

1. Turn off the main power.

2. Slide the portion “A” in the direction of the arrow to

unlock and pull out the flexible card wire.

Installation

Recessed portion

. Do not insert the flexible card wire sideways.

. Confirm that there is no stain or dust on the contact

surface of the flexible card wire.

Insulated surface (Blue)

Type B

1. Slide the portion “A” in the direction of the arrow and

securely insert the insulated surface (Blue) of the

flexible card wire into the connector in the direction

that is shown against the recessed portion of the

connector.

2. Return the portion “A” to its original position and lock

the connector.

HDCU-950 IMM

1-31 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-9. Installing the RM-B750

1-9-2. Installing the RM-B750

3. Disconnect the connector (CN104) from the MPU-124

board and the connector (CN2) from the VA-211

board respectively.

This section describes the installation procedure when the

front panel of the remote control unit RM-B750 is used by

being installed to the unit.

Life of flexile card wire will be significantly shortened

if it is folded. Be very careful not to fold the flexible

card wire.

Removing the Front Panel from the RM-B750

1. Loosen the screw (with drop-safe) of the RM-B750

and open the cover in the direction of the arrow.

4. Remove the screw and remove the front panel in the

direction of the arrow.

MPU-124 board

(CN104)

Screw

(with drop-safe)

Front panel

B3 x 5

Flexible card wire

VA-211 board

Cover

CN2

Flexible card wire

2. Loosen the four screws (with drop-safe) and open the

front panel and the rear panel in the direction of the

respective arrows.

Rear panel

Front panel

Screws

(with

drop-safe)

Screws

(with drop-safe)

HDCU-950 IMM

1-32 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-9. Installing the RM-B750

11. Connect the flexible card wire to the connector (CN2)

of the AU-281 board.

Installing the Front Panel to the Unit

5. Turn off the power and disconnect the plug from the

outlet.

. Do not insert the flexible card wire sideways. Insert

it securely to the deep end as shown in the Fig 1.

If the connection is not performed correctly, it may

cause an failure.

6. Open the front panel of the unit.

(Refer to Section 1-8-1. step 2)

7. Remove the screw.

. Life of flexile card wire will be significantly short-

ened if it is folded. Be very careful not to fold the

flexible card wire.

. Install the connector so that the excessive force is

not given to it.

8. Slide the front panel in the direction of the arrow to

extract the pin from the potbellied hole and remove the

front panel.

Potbellied hole

12. Close the front panel of the RM-B750 in the direction

of the arrow and secure it with the two screws (with

drop-safe).

Insulated surface (Blue)

B3 x 5

Front panel

9. Insert the pin into the potbellied hole of the front panel

of the RM-B750 removed in step 4 and slide the pin in

the direction of the arrow.

7.5 mm or less

7.5 mm or more

Fig. 1

CN2

Front panel of

the RM-B750

Confirm that the pin is hooked to the potbellied hole so

that front panel does not drop.

Screw

(with drop-safe)

10. Secure the front panel of the RM-B750 with the screw

removed in step 7.

Potbellied hole

AU-281 board

Flexible card wire

S206

Screw (with drop-safe)

13. Upon completion of front panel installation, check that

the switch S206 (CCU-PW) on the MPU-124 board of

the RM-B750 is ON.

B3 x 5

Front panel of

the RM-B750

The switch S206 (CCU-PW) on the MPU-124 board is

the power ON/OFF switch for the RM-B750. If it is set

to OFF, the panel functions are stopped.

HDCU-950 IMM

1-33 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-10. Installing in 19-inch Rack

Installation

The two HDCU-950 can be mounted in parallel in a 19-

inch EIA standard rack by using the rack mount adapter

RMM-301 (optional). (Height three unit)

1. Secure the RMM-301 in the 19-inch EIA standard rack

with the four B5 screws (6 mm or longer).

If the rack falls due to the weight of the equipment, it may

57.2 mm

cause death or major injury.

To prevent the rack from falling or moving, be sure to fix

the rack to the floor.

B5 screw

(6 mm or longer)

If the rack falls, death or serious injury may result.

When attaching the unit, be sure to fix the rack to the floor

and be careful not to attach at a height of 1.2 m or higher

from the floor.

RMM-301

B5 screw

(6 mm or longer)

Use the specified rack mount adapter.

If not, injury could occur by drop of the unit because

strength of the shelf board is not enough.

2. Secure the unit with the supplied four screws (B4 x 6)

and the four washers.

Mount the unit with more than two persons.

A one-man job may cause injury.

Be careful not to catch your finger or hand in the rack

mount rail.

Mount in the rack in a stable position.

Injury could occur by drop of the unit in unbalance

condition of installation or removal.

Install in a posture of stability and carefully.

Required Parts

. Rack mount adapter RMM-301

1 set

. Screw (B4 x 6) (supplied with the RMM-301) 4 pcs

Sony part No. : 7-682-560-04

. Washer (W4, SMALL)

(supplied with the RMM-301)

Sony part No. : 7-688-004-03

. B5 screw (6 mm or longer)

4 pcs

B4 x 6

HDCU-950 IMM

1-34 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

Section 2

System Setup

2-1. System Connection

This unit can support input and output of multiple formats. It can also support various types of user’s

format by installing the optional circuit boards.

The slots to which the circuit boards are inserted and the internal switches setting differ depending upon

the system used. They need to be set according to the system used.

For the installation procedure, refer to “1-8. Installing the HKCU-951/953”. For details of the slots in use

on each board and for details of the switch setting on board, refer to this section and “1-6. Setting of

Switches on Boards”.

List of optional boards

Model name

Board name

(Slots on the front)

(Slots on the rear)

SD Encoder Unit HKCU-951

EN-145

FC-88

VDA-61

SDI-73

HD Frame Rate Converter Unit HKCU-953

HKCU-951: Install the HKCU-951 when you want to use the analog composite signal or analog component signal as the main signal.

HKCU-953: Install the HKCU-953 when you want to shoot picture in 24PsF mode of the camera, and you need the HD (SD) signal

created by the 2 to 3 Pulled Down method.

HDCU-950 (without optional board installed)

HDCU-950 with HKCU-953

CAMERA

REFERENCE

PROMPTER

REFERENCE

PROMPTER

MIC1

SD SDI

OUT 1

SD SDI

OUT 1

HD SDI

OUT 1

SD SDI

OUT 2

SD SDI

OUT 2

HD SDI

OUT 2

SERIAL

OUT 1

SERIAL

OUT 1

RET1

RET2

RET3

RET1

RET2

RET3

MIC2

SYNC OUT

PIX

OUT

SERIAL

OUT 2

PIX

OUT

FRAME

REF IN

SERIAL

OUT 2

OUT

MONI

RCP/CNU

WF MODE

OUT

WF MODE

MIC REMOTE

INCOM/TALLY/PGM

HDCU-950 with HKCU-951

CAMERA

REFERENCE

PROMPTER

MIC1

SD SDI

VBS

OUT

OUT 1

SD SDI

OUT 2

SERIAL

OUT 1

RET1

RET2

RET3

Y/G

MIC2

SYNC OUT

PIX

OUT

SERIAL

OUT 2

B-Y/B

R-Y/R

OUT

MONI

RCP/CNU

WF MODE

MIC REMOTE

INCOM/TALLY/PGM

HDCU-950 IMM

2-1 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

2-1. System Connection

2-1-1. Standard System

PIX/WF

(HDCU-950)

VCS-700

HDCU-950

HKCU-951

HKCU-953

CNU-700

HDC-950 + CA-905L

MSU-700A/750

PIX/WF (HDCU-950)

HDCU-950

HKCU-951

HKCU-953

HDC-950 + CA-905L

HDC-950

HDCU-950

HKCU-951

HKCU-953

HDC-950

HD-SDI Monitor

HDCU-950

HKCU-951

HKCU-953

MSU-700A/750

RCP-700/701

RCP-720/721

RCP-730/731

RCP-740/741

RCP-750/751

Combination of boards

Board name

Slot 1

Slot2

Slot3

Slot4

Slot5

Slot6

HDCU-950

Front side

AT-149

AVP-4

DTX-1

SDI-70

DTX-1

SDI-70

DTX-1

SDI-70

DRX-1

HIF-5

DRX-1

HIF-5

DRX-1

HIF-5

RC-91

DIF-124

RC-91

DIF-124

FC-88

Rear side

Front side

Rear side

Front side

Rear side

CN-2219

AT-149

CN-2220

AVP-4

HKCU-951 installed

HKCU-953 installed

EN-145

VDA-61

RC-91

DIF-124

CN-2219

AT-149

CN-2220

AVP-4

CN-2219

CN-2220

SDI-73

HDCU-950 IMM

2-2 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

2-1. System Connection

2-1-2. Standard HD/SD System

Example of connection

SYNC OUT (HD)

HD REFERENCE SIGNAL

PROMPTER SIGNAL

PROMPTER IN

SERIAL RET INPUT 1 to 3

HD-SDI RETURN VIDEO SIGNAL

REFERENCE SIGNAL

REFERENCE IN

HDC-950 + CA-905L

SERIAL OUTPUT 1, 2

HD-SDI SIGNAL

CAMERA

REFERENCE

PROMPTER

MIC1

SD SDI

OUT 1

SD SDI

OUT 2

SERIAL

OUT 1

RET1

RET2

RET3

SD ANALOG Monitor

MIC2

SYNC OUT

PIX

OUT

SERIAL

OUT 2

OUT

MONI

RCP/CNU

WF MODE

Waveform Monitor

HD-SDI Monitor

MIC REMOTE

INCOM/TALLY/PGM

HDCU-950

SYNC OUT (HD)

HD REFERENCE SIGNAL

SERIAL RET INPUT 1 to 3

HD-SDI RETURN VIDEO SIGNAL

SERIAL OUTPUT 1, 2

HD-SDI SIGNAL

HDC-950 + CA-905L

CAMERA

REFERENCE

PROMPTER

MIC1

SD SDI

OUT 1

SD ANALOG Monitor

SD SDI

OUT 2

SERIAL

OUT 1

RET1

RET2

RET3

MIC2

SYNC OUT

PIX

OUT

SERIAL

OUT 2

OUT

MONI

RCP/CNU

WF MODE

Waveform Monitor

MIC REMOTE

INCOM/TALLY/PGM

HDCU-950

HD-SDI Monitor

SD ANALOG VIDEO SIGNAL

Next HDCU-950

SD REFERENCE SIGNAL

CNU-700

Terminated at 75 Z

Download from Www.Somanuals.com. All Manuals Search And Download.

HDCU-950 IMM

2-3 (E)

2-1. System Connection

2-1-3. HD/SD Film Like System

Example of connection

SYNC OUT

SYNC SIGNAL

PROMPTER IN

PROMPTER SIGNAL

SDI RETURN VIDEO SIGNAL

REFERENCE SIGNAL

HD-SDI SIGNAL

SERIAL RET INPUT 1 to 3

REFERENCE IN

SERIAL

OUTPUT 1, 2

HDC-950 + CA-905L

HD SDI OUT 1, 2

FRAME REF IN

HD-SDI SIGNAL

SUB REFERENCE SIGNAL

SD-SDI SIGNAL

CAMERA

REFERENCE

PROMPTER

MIC1

SD SDI

OUT 1

HD SDI

OUT 1

SD SDI

OUT 2

HD SDI

OUT 2

SERIAL

OUT 1

RET1

RET2

RET3

MIC2

SYNC OUT

PIX

OUT

FRAME

REF IN

SERIAL

OUT 2

Picture Monitor

OUT

MONI

RCP/CNU

OUT

WF MODE

MIC REMOTE

INCOM/TALLY/PGM

Waveform Monitor

HDCU-950

SYNC OUT

SYNC SIGNAL

SDI RETURN VIDEO SIGNAL

HD-SDI SIGNAL

SERIAL RET INPUT

1 to 3

SERIAL

OUTPUT 1, 2

HDC-950 + CA-905L

HD SDI OUT 1, 2

HD-SDI SIGNAL

SD-SDI SIGNAL

CAMERA

REFERENCE

PROMPTER

MIC1

SD SDI

OUT 1

HD SDI

OUT 1

SD SDI

OUT 2

HD SDI

OUT 2

SERIAL

OUT 1

RET1

RET2

RET3

MIC2

SYNC OUT

PIX

OUT

FRAME

REF IN

SERIAL

OUT 2

Picture Monitor

OUT

MONI

RCP/CNU

OUT

WF MODE

MIC REMOTE

INCOM/TALLY/PGM

Waveform Monitor

HDCU-950

SD ANALOG VIDEO SIGNAL

SD REFERENCE SIGNAL

Next HDCU-950

CNU-700

Terminated at 75 Z

Download from Www.Somanuals.com. All Manuals Search And Download.

HDCU-950 IMM

2-4 (E)

2-1. System Connection

2-1-4. Analog NTSC/PAL System

Example of connection

SD SYNC REFERENCE SIGNAL

PROMPTER SIGNAL

SYNC OUT

PROMPTER IN

RET INPUT 1 to 3

ANALOG RETURN VIDEO SIGNAL

REFERENCE SIGNAL

REFERENCE IN

RGB/

HDC-950 + CA-905L

Component OUT

ANALOG COMPONENT VIDEO SIGNAL

ANALOG COMPOSITE VIDEO SIGNAL

VBS OUT

CAMERA

REFERENCE

PROMPTER

MIC1

SD SDI

OUT 1

VBS

OUT

SD SDI

OUT 2

SERIAL

OUT 1

RET1

RET2

RET3

Y/G

MIC2

SYNC OUT

PIX

OUT

SERIAL

OUT 2

B-Y/B

R-Y/R

OUT

MONI

RCP/CNU

WF MODE

MIC REMOTE

INCOM/TALLY/PGM

HDCU-950

SYNC OUT

SD SYNC REFERENCE SIGNAL

ANALOG RETURN VIDEO SIGNAL

RET INPUT 1 to 3

RGB/

Component OUT

ANALOG COMPONENT VIDEO SIGNAL

ANALOG COMPOSITE VIDEO SIGNAL

VBS OUT

HDC-950 + CA-905L

CAMERA

REFERENCE

PROMPTER

MIC1

SD SDI

OUT 1

VBS

OUT

SD SDI

OUT 2

SERIAL

OUT 1

RET1

RET2

RET3

Y/G

MIC2

SYNC OUT

PIX

OUT

SERIAL

OUT 2

B-Y/B

R-Y/R

OUT

MONI

RCP/CNU

WF MODE

MIC REMOTE

INCOM/TALLY/PGM

HDCU-950

Next HDCU-950

WF 2

PIX 2

SD ANALOG VIDEO SIGNAL

SD REFERENCE SIGNAL

VCS

VCS-700

PIX 1

WF 1

REMOTE

PIX A

WF A

CNU-700

HDCU-950 IMM

Terminated at 75 Z

2-5 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

2-2. Setting the System Format

2-2-1. Setting the Multi-Format

Set format of the signal that is output from this unit.

Normally the Multi-Format is set from RM/MSU or a device that is connected outside. However, it can also be set by the

switches on the AT-149 board or FC-88 (HKCU-953) board.

1. Setting the HD-SDI output

Set format of the signal that is output as the HD-SDI signal. At the same time, this setting becomes the shooting mode of

the camera.

(1) Set the field frequency coefficient.

Setup switch : S420 on the AT-149 board (Factory setting : REMOTE)

1.001 :

1.000 :

Set the field frequency to 1/1.001 times

(Set the field frequency to 1.001 when using NTSC (525/60) signal in the SD system.)

Set the field frequency to 1 time.

(Set the field frequency to 1.000 when using PAL (625/50) signal in the SD system.)

REMOTE : Set it with RM/MSU, etc., that is connected outside.

(2) Set the field frequency.

Setup switch: S418 on the AT-149 board (Factory setting: 60 V)

60 V : When the FC-88 board (HKCU-953) is not used but either the 60 field HD signal or the NTSC SD (525/60)

signal is used.

50 V : When the FC-88 board (HKCU-953) is not used but either the 50 field HD signal or the PAL SD (625/50)

signal is used.

48 V : Only the 24PsF progressive system is supported.

(3) Set the shooting mode of the camera.

Setup switch : S419 on the AT-149 board (Factory setting : INTR)

INTR : When shooting with interlacing system.

PROG : When shooting with progressive (PsF) system.

540P : When shooting with 540-60P system. (At present, this function is not supported.)

If you select a format of 48i (48 field interlace) or other format that is not supported by the HDCU-950, the setting causes

an error and the indicators (D201 to D205) on the AT-149 board flash.

2. Setting the SD signal output

When S420 on the AT-149 board is set to the position other than REMOTE, set the SD signal output to NTSC (525/60) or

PAL (625/50).

Setup switch : S423-1 on the AT-149 board (Factory setting : OFF)

ON : PAL (625/50)

OFF : NTSC (525/60)

3. Setting the frame conversion (when the HKCU-953 is installed)

When the shooting mode of the camera is set to 24PsF, set the HD-SDI signal format that is output from the HKCU-953.

Setup switch : S2 on the FC-88 board (Factory setting: OFF)

ON : When the shooting mode of the camera is set to 24PsF, the frame frequency conversion is implemented.

OFF : The frame frequency is not converted. The same signal as the main HD-SDI signal is output.

The setting of the frame conversion frequency must follow the set format of the SD signal output.

When S423-1 on the AT-149 board is set to OFF (NTSC), the frame frequency is converted to 60i (30 Hz).

When S423-1 on the AT-149 board is set to ON (PAL), the frame frequency is converted to 50i (25 Hz).

HDCU-950 IMM

2-6 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

2-2. Setting the System Format

2-2-2. Setting the Reference Input

Normally the reference input is set from RM/MSU or a device that is connected outside. However, it can also be set by the

switch on the AT-149 board.

1. Setting the reference input signal format

Setup switch : REFERENCE switch (S427) on the AT-149 panel (Factory setting : REM)

HD : When the HD analog ternary SYNC is used. (This unit supports the frame frequency automatically.)

BB : When the BB (black burst) signal of SD is used.

REM :When the reference is set from RM/MSU or a device that is connected outside.

When a position other than REM is set, all of the REFERENCE settings including the phase adjustment must be locally set.

When the SD signal output is set to NTSC in setting the Multi-Format, if the 10F-BB signal to which the 10 frame se-

quence flag is added as the reference signal of SD is used, the frame sequence of the 24PsF signal and the 60i signal can be

locked even if the sub reference signal is not input by setting S416 on the AT-149 board to ON.

2. Setting the sub reference input signal (when the HKCU-953 is installed)

The sub reference signal can be set with S5 on the FC-88 board (HKCU-953). However, the input signal can automatically

be identified by setting the switch to AUTO.

Set the switch to AUTO normally. Input the frame frequency signal that is different from the main reference signal for the

sub reference signal

Setup switch : S5 on the FC-88 board (Factory setting : 0)

0 (AUTO) :

1 (FRAME REF HD) :

2 (FRAME REF SD) :

Identifies the sub reference input signal automatically.

When the ternary SYNC of HD is input.

When the composite SYNC of SD is input.

3 (FRAME REF S.SYNC) : When the frame SYNC pulse gate signal that is output from the other CCU is input.

When the sub reference is not input, the pulse gate signal of the frame sync is output from the loop-through output terminal.

You can lock the frame sequence between multiple CCUs if you connect this signal to the sub reference input of other

CCUs.

HDCU-950 IMM

2-7 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

2-3. Audio System

. Selecting the producer line :

Set switches S610/611 (PROD SELECT) on the AVP-4

2-3-1. Setting the Intercom System

board according to the system used.

Factory setting : 4W (S611)

This unit can be connected to the intercom lines (producer

line and engineer line) of the two independent systems and

can be switch them.

RTS (S610)

. Selecting the engineer line :

Set switches S710/711 (ENG SELECT) on the AVP-4

The intercom systems conforming to this unit are 4W, RTS

and Clear-Com. The internal switches of the unit need to

be set according to the system used.

board according to the system used.

Factory setting : 4W (S711)

RTS (S710)

. When the intercom line is 1 channel :

Set switch S12 (INPUT INCOM SELECT) on the AVP-

4 board to 1 ch. Then, connect the intercom line to the

producer line of this unit.

When the switch is set in this position, connection of the

intercom line of this unit is fixed to the producer line

regardless of the setting of the INCOM PROD/ENG

switch of the HDC-950/930 and the INCOM SELECT

switch on the front panel of this unit.

. When the intercom line is 2 channels :

Set switch S12 (INPUT INCOM SELECT) on the AVP-

4 board to 2ch.

S500

S501

RV401

Factory setting : 2ch

S711

S611

Adjusting the RTS cancel

When the RTS intercom system is used, the following

adjustment also needs to be made.

(1) Connect a headset to the INCOM connector on the

front and perform the procedure described in the follow-

ing paragraph “2. Setting the headset microphone”.

(2) Fully rotate the SIDE TONE control of the AVP-4

board panel counter-clockwise to minimize the side tone.

(3) Set the INCOM SELECT switch on the front panel to

PROD.

(4) Speak into the microphone of the headset and adjust

the 2WIRE CANCEL PROD control of the AVP-4

board panel to minimize the side tone.

S710 S610

S12

(5) Set the INCOM SELECT switch on the front panel to

ENG.

PGM SELECT switch

PGM LEVEL control

SIDE TONE control

2WIRE CANCEL PROD control

2WIRE CANCEL ENG control

(6) Speak into the microphone of the headset and adjust

the 2WIRE CANCEL ENG control of the AVP-4

board panel to minimize the side tone.

(7) Return the SIDE TONE control on the AVP-4 board panel

to its original position or to the desired position of user.

AVP-4 board (A side/panel side)

1. Selecting the intercom system

Select a system (4W, RTS or Clear-Com) respectively for

the engineer line and the producer line according to the

system used. Then, select the number of intercom line

systems (1ch or 2ch).

When setting S611 and S711 to RTS, be sure to connect

them to the RTS system. Otherwise, they oscillate and

have adverse effects on the peripheral circuits.

HDCU-950 IMM

2-8 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

2-3. Audio System

2. Setting the headset microphone

. Selecting the PGM audio signal

Set switch S4 (TALK GAIN) on the AU-281 board

according to the type of headset microphone to be connect-

ed to the INCOM connector on the front.

When using a carbon microphone : CARBON

(Sensitivity _20 dB, power is supplied.) (factory setting)

When using a electric condenser microphone : ECM

(Sensitivity _40 dB, power is supplied.)

Set the PGM audio signal of the headset connected to the

INCOM connector on the front with the PGM SELECT

switch on the AVP-4 board panel according to user’s

request.

Selecting PGM 1 : PGM 1 (Factory setting)

Selecting mix of PGM 1 and PGM 2 :Mix

Selecting PGM 2 : PGM 2

Adjusting the mix amount of the PGM audio signal

Use the PGM 1, 2 LEVEL control on the AVP-4 board

panel and adjust mix amount of the PGM audio signal of

the headset connected to the INCOM connector on the

front according to user’s request.

When using a dynamic microphone : DYNAMIC

(Sensitivity _60 dB, power is not supplied.)

4. Selecting an intercom line to be connected to

the INCOM connector

POWER

CAM

CABLE

ALRAM

OPEN

MAIN

Use the switch on the front panel to select the intercom line

to be connected to the INCOM connector on the front as

follows.

SHORT

INCOM MIC-ON

PROD

PRIV

OFF

INCOM SELECT switch

. When connecting to the producer line :

Set the INCOM SELECT switch to PROD.

. When connecting to the engineer line :

Set the INCOM SELECT switch to ENG.

. When connecting only a camera :

Set the INCOM SELECT switch to PRIV. When this

position is set, the intercom from outside is cut and the

system consists of the intercom and camera.

PGM

ENG

. Adjusting the TALK level

Adjust the headset TALK level with control RV401

(TALK LEV) on the AVP-4 board according to user’s

request.

. Adjusting amount of the side tone

Use the SIDE TONE control on the AVP-4 board panel and

adjust amount of the side tone to be connected to the

INCOM connector on the front according to user’s request.

When switch S12 (INPUT INCOM SELECT) on the AVP-

4 board is set to 1 ch, the INCOM SELECT switch on the

front panel of the unit and the camera are fixed to the

producer line regardless of the setting.

3. Setting the input level of the PGM audio signal

Set switches S500 (PGM1 SEL) and S501 (PGM2 SEL) on

the AVP-4 board to 0 dBu or _20 dBu according to each

level of audio 1 and 2 of the system.

5. Setting the AVP-4 board switch

The flow of the switch setting on the AVP-4 board and the

intercom signals is as follows.

PGM 1/PGM 2

INCOM/TALLY/PGM

Factory setting : 0 dBu

connector on the rearpanel

S501

Program line 2

PGM 2

0dB/–20dB

S500

3. Select the

X 4

PGM audio input level

Program line 0

PGM 1

G 5

0dB/–20dB

S610,611

System intercom

X @/

Y 8

G 7

X 5

Y !.

INCOM 1

ENG/PROD (Camera side)

2CH/1CH (S12)

Talk

Producer line

Receive

PRIV(Front panel)

4W/RTS/Clear-Com

S710,711

INCOM 1

ENG/PROD (Camera side)

2CH/1CH (S12)

X !\

Y 3

G 2

X 1

Y !]

Talk

Engineer line

Receive

PRIV(Front panel)

RV201,202

4W/RTS/Clear-Com

3. Set the mix amout of

PGM audio signal

1. Select the input 4W/RTS/

Clear-Com

INCOM SELECT switch

on board panel

4. Setting for the

INCOM connector

on the front panel

To the INCOM connector on the front panel

HDCU-950 IMM

2-9 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

2-3. Audio System

Setting the microphone input gain of the video camera

2-3-2. Setting the Microphone

Pin No.

This unit can output the two independent microphone lines

(MIC 1, MIC 2) of video camera HDC-950/930 as it

receives these MIC signals.

60 dB

50 dB

40 dB

30 dB

20 dB

L (H)

H (L)

L (H)

Controlling the Microphone Input Gain Using the

Remote Control

H :

L :

+5 V or OPEN

GND

This unit can adjust the input gain of the MIC connector of

camera HDC-950/930 using the remote control in the

range of 60 dB to 20 dB in 10 dB steps using either of the

following methods.

Input resistance : Pulled-up 100 kZ +5 V

The setup for HDCU-700A mode is shown in parenthesis ( ).

In the case of HDCU-700A mode : S423-2/AT-149 → ON

3. Adjusting the MIC signal phase

1. Adjusting the microphone input gain using

the MIC LEVEL switch

MIC LEVEL switch

AVP-4 board (panel side)

When the MIC REMOTE connector on the rear is connect-

ed to nothing or the levels of pin-8 (MIC 1) and pin-15

(MIC 2) of the MIC REMOTE connector are High, use the

MIC LEVEL switch on the AVP-4 board panel of the unit

to set the microphone input level.

S15

AVP-4 board (A side)

Factory setting : NORM (60 dB)

When the PGM microphone signal phase is in advance

with respect to the video signal phase in use, adjust the

audio phase using the switch S15 (MIC DELAY) on the

AVP-4 board to adjust amount of audio delay. Each step

of the switch corresponds to about 5 ms delay.

Example 7 : 1 FRAME DELAY (30 FRAME/SEC)

8 : 1 FRAME DELAY (25 FRAME/SEC)

2. Adjusting the microphone input gain using

the MIC REMOTE connector

Set the microphone input gain control to ON or OFF via

pin-8 and pin-15 of the MIC REMOTE connector on the

rear as shown below. The input gain can be controlled via

pin-5, pin-6 and pin-7 as shown in the table on the top-

right.

Factory setting : 0

Setting the microphone input control of the video camera

Pin No.

Microphone connector

MIC IN CH-1

MIC IN CH-2

OFF

Internal setup (MIC LEVEL switch on the

AVP-4 board panel)

HDCU-950 IMM

2-10 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

2-3. Audio System

2-4. Systems

Setting the Microphone Output Level

2-4-1. Setting the Tally System

This unit supports the red tally and the green tally. It also

supports the MAKING CONTACT and supplying power

(24 V/TTL). Set the switches on the AVP-4 board accord-

ing to the system used as follows :

S503

S502

RV500

RV501

S101 S100

S103 S102

AVP-4 board (A side)

Select the microphone output signal level (0 dB, _20 dBu)

from the MIC 1, 2 connector on the rear using the switches

on the AVP-4 board.

Setting the output level of MIC 1 :

Switch S503 (MIC 1 OUT LEVEL)

Setting the output level of MIC 2 :

Switch S603 (MIC 2 OUT LEVEL)

Factory setting : 0 dBu (both S502 and S503)

AVP-4 board (A side)

Set the tally system as shown in the following table.

Setting the tally system

The microphone output signal level from the MIC 1, 2

connector on the rear can be adjusted using the volume on

the AVP-4 board.

Red tally

S100

Green tally

S101

Switch

S102

S103

Setting the output level of MIC 1 :

MAKING

CONTACT

1RV500 (MIC 1 OUT LEVEL)

Setting the output level of MIC 2 :

1RV501 (MIC 2 OUT LEVEL)

CONTACT

Supplying

24 V power

POWER

TTL

POWER

TTL

Supplying

5 V power

Switches S100 and S101 are set to CONTACT when the unit is shipped from

the factory.

HDCU-950 IMM

2-11 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

2-4. Systems

2-4-2. Setting the Camera Number

2-4-3. Connecting the Control, Intercom and

Tally Audio Signals

System that does not use CNU-700/500

Use switch S421 on the AT-149 board to set the camera

number.

An example of connection is described on the next page.

Use switches 1 to 4 to set the first digit and use switches 5

to 8 to set the second digit. “0” to “f” can be set as each

digit, but “a” to “f” are invalid. Camera numbers 1 to 96

can be set.

In case of cascaded connection of the DVS-V1201

SD digital video routing switcher :

Set unit address switch “5” of REMOTE2 of the DVS-

V1201 SD digital video routing switcher to ON and set the

other switches to OFF. For cascaded connection of the

DVS-V1201 SD digital video routing switcher when at

least 13 cameras are used, set unit address switch “6” of

the second camera to ON and set the other switches to

OFF.

S421

AT-149 board (A side)

(Example of setting)

First digit

Second digit

Camera

number

System that uses CNU-700/500

The CCU connector number on the rear of the CNU-700/

500 is the camera number. For example, the camera

number of the CCU video camera that is connected to the

CCU 1 connector is 1.

HDCU-950 IMM

2-12 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

2-4. Systems

HDCU-950 [1]

+B M3

CAMERA

REFERENCE

PROMPTER

MIC1

SD SDI

OUT 1

SD SDI

OUT 2

SERIAL

OUT 1

RET1

RET2

RET3

MIC2

SYNC OUT

PIX

OUT

SERIAL

OUT 2

OUT

MONI

RCP/CNU

WF MODE

RCP/CNU

INTERCOM/

TALLY/PGM

MIC REMOTE

INCOM/TALLY/PGM

INTERCOM/PROGRAM/

AUDIO/TALLY

MIC OUT

MIC OUTPUT

MIC CONTROL and TALLY

MIC REMOTE or WF REMOTE

WF MODE

WF MONITOR CONTROL

WF MONITOR

SEQ CONTROL

HDCU-950 [2]

+B M3

CAMERA

REFERENCE

PROMPTER

MIC1

SD SDI

OUT 1

SD SDI

OUT 2

SERIAL

OUT 1

RET1

RET2

RET3

MIC2

SYNC OUT

PIX

OUT

SERIAL

OUT 2

OUT

MONI

RCP/CNU

WF MODE

INTERCOM/

TALLY/PGM

MIC REMOTE

INCOM/TALLY/PGM

INTERCOM/PROGRAM/

AUDIO/TALLY

MIC OUT

MIC OUTPUT

MIC CONTROL and TALLY

MIC REMOTE or WF REMOTE

WF MODE

WF MONITOR CONTROL

WF MONITOR

SEQ CONTROL

RCP/CNU

CNU-700

CCU1

CCU2

VCS

VSC-700

MSU

REMOTE

MSU-700A

CCU/CNU

WF MODE

RCP1

RCP2

RS232C

WF MONITOR CONTROL

HDS-X3400

REMOTE3

CCU/CNU

REMOTE2

DVS-V1201

REMOTE1

RCP-740/741 [1]

PREVIEW

RCP-740/741 [2]

SWITCHER

HDCU-950 IMM

2-13 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

2-5. Video Signal System

Adjusting the Phase of the Sync Signal

Adjust the phase of the output signal to match it with that

of the reference signal. Perform the adjustment using the

switch on the AT-149/EN-145 board (HKCU-951) panel of

the unit. The adjustment also can be performed on the

maintenance menu of the MSU-700A/750. For more

details, refer to the System Manual.

The equipment that is used for this unit and the HDC-950/

930 series camera system were set to the specified level

when shipped from the factory. Before operating, check

the signal levels between each equipment and adjust them

if required. Some adjustments can be performed using the

maintenance menu of the MSU-700A/750 instead of using

the control or switches on the board. Perform the basic

adjustments on the board and perform the fine adjustments

on the maintenance menu.

How to adjust on the AT-149 board/EN-145 board

(HKCU-951) of the unit

2-5-1. Selecting the Input/Output Signal

REFERENCE SIGNAL

SELECT switch

H PHASE STEP switch

Select the input/output terminal signal of the rear panel

according to the video system to be installed.

H PHASE COARSE switch

2-5-2. Adjusting the Signal Phase

AT-149 board (panel side)

Adjust the signal phase of the unit. Before adjustment,

input the next sync signal to the unit and each of the

equipment used.

SC PHASE switch

HDCU-950

EN-145 board (panel side)

REFERENCE

1. Select the type of external sync signal using the

REFERENCE SIGNAL selector switch on the AT-149

board panel.

HD ternary SYNC : 0.6 V p-p

black burst signal : 40 IRE (0.3 V p-p)

(SMPTE318M (10F-BB) is also acceptable.)

HD : HD ternary SYNC

BB : BB (black burst) signal

REM :Control is perfomed by MSU, etc,. connected

outside.

Factory setting : REM

When the VBS signal of HKCU-951 is used when (SC

phase lock is required), use the black burst signal.

2. When setting HD in step 1 :

HKCU-953

1) Coarse-adjust the H phase using H PHASE STEP

switch on the AT-149 board panel, then fine-

adjust it using the H PHASE COARSE switch on

the AT-149 board panel.

FRAME REFERENCE

HD ternary SYNC : 0.6 V p-p

black burst signal : 40 IRE (0.3 V p-p)

When selecting BB in step 1 :

sequence pulse :

40 IRE (0.3 V p-p)

1) Coarse-adjust the H phase using H PHASE SETP

switch on the AT-149 board panel, then fine-

adjust it using the H PHASE COARSE switch on

the AT-149 board panel.

2) Adjust the SC phase using switch SC PHASE on

the EN-145 board (HKCU-951) panel (when the

BB signal is selected as a reference).

CNU-700/500

Signal in which sync signal is included

Signal level :

40 IRE (0.3 V p-p)

Waveform monitor

Sync signal specified by waveform monitor

When using 10F-BB (NTSC 10-field sequence BB) of

SMPTE318M as BB, the frame sequences of the 30 Hz

frame frequency and the 24 Hz frame frequency can be

locked by setting switch S416 (REF-10F-BB) on the

AT-149 board to ON.

HDCU-950 IMM

2-14 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

2-5. Video Signal System

2-5-3. Setting Aspect Ratio Conversion

during Down-convert

How to set using the MIC REMOTE connector at

the rear of the unit

1. Set switch S423-3 (MIC REMOTE/WF REMOTE) on

the AT-149 board to MIC REMOTE (OFF).

2. Set pin-12 (ASPECT REMOTE ON/OFF) of the MIC

REMOTE connector at the rear to L.

3. Set pin-13 (ASPECT CTL CONT1) and pin-14

(ASPECT CTL CONT2) of the MIC REMOTE

connector at the rear according to the desired aspect

ratio while referring to the following table.

In the HDC-950/930 series camera system, the aspect ratio

can be switched by using the HDCU-950 and MSU-700A/

750 according to the system during HD-SD down-convert.

Set the desired aspect ratio using the MIC REMOTE

connector at the rear of the unit or the switch on the AT-

149 and RC-91 boards.

The aspect ratio also can be set on the maintenance menu

or the configuration menu of the MSU-700A/750. For

more details, refer to the System Manual. The aspect ratio

of the following four types can be switched in this system.

Pin-13

Pin-14

Aspect ratio

(ASPECT

CTL CONT1)

(ASPECT

CTL CONT2)

Squeeze (16 : 9)

Edge-crop (4 : 3)

Squeeze :

The HD video signal of 16 : 9 is converted to

the SD signal as it is. (16 : 9)

Edge-crop :

Video signal as large as 4 : 3 is cut from the

HD video signal and is converted to the SD

signal. (4 : 3)

Depends on the

setting switches on

the RC-91 board.

Letter box :

The HD video signal of 16 : 9 is inserted into

the picture frame of 4 : 3 as it is and convert-

ed to the SD signal. (4 : 3) (The black level is

inserted into the top and bottom of the

picture.)

Letter box (4 : 3)

How to set on the RC-91 board of the unit

1. Set ASPECT REMOTE/LOCAL switch on the RC-91

board panel to LOCAL.

2. Set ASPECT SEL switch, EC POSITION SEL switch

and EC POSITION CONT switch on the RC-91 board

panel according to the desired aspect ratio.

Semi-letter box : Video signal as large as 15 : 9, 14 : 9 or 13 :

9 is cut from the HD video signal, is inserted

into the picture frame of 4 : 3 and is convert-

ed to the SD signal. (4 : 3)

(The black level is inserted into the top and

bottom of the picture.)

When setting ASPECT SEL switch to EC (edge-crop),

CROP POSITION (horizontal cutting position) can be

changed by using EC POSITION SEL switch and EC

POSITION CONT switch.

S10

For more details, refer to Section 1-6-6, “Setting of

Switches on Boards_RC-91 Board”.

ASPECT SEL switch

EC POSITION SEL switch

EC POSITION CONT switch

RC-91 board (A side/panel side)

S423

AT-149 board (A side)

HDCU-950 IMM

2-15 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

2-5. Video Signal System

Examples of display

16 : 9 picture (picture from camera)

Letter box (16 : 9)

S7/RC-91 → LB

S10-3, -4/RC-91 → OFF

The 16 : 9 ratio picture is inserted into

the 4 : 3 ratio picture without changing

the ratio and is output in the SD SDI format.

Horizontal cutting position of 16 : 9

Horizontal cutting position of 15 : 9

Horizontal cutting position of 14 : 9

Horizontal cutting position of 13 : 9

Horizontal cutting position of 4 : 3 (12 : 9)

Semi-letter box (15 : 9)

S7/RC-91 → LB

S10-3/RC-91 → OFF

S10-4/RC-91 → ON

Picture whose aspect ratio is converted

(SD SDI output)

The picture that is cut out with the aspect

ratio of 15 : 9, is inserted into the 4 : 3 ratio

picture and is output in the SD SDI format.

Edge-crop

S7/RC-91 → EC

The crop position can be changed by

using S8 and S9 on the RC-91 board.

Semi-letter box (14 : 9)

S7/RC-91 → LB

S10-3/RC-91 → ON

S10-4/RC-91 → OFF

The picture that is cut out with the aspect

ratio of 14 : 9, is inserted into the 4 : 3 ratio

picture and is output in the SD SDI format.

Squeeze

S7/RC-91 → SQ

The 16 : 9 ratio picture is output in the

SD SDI format without changing the ratio.

Semi-letter box (13 : 9)

S7/RC-91 → LB

S10-3, -4/RC-91 → ON

The picture that is cut out with the aspect

ratio of 13 : 9, is inserted into the 4 : 3 ratio

HDCU-950 IMM

2-16 (E)

picture and is output in the SD SDI format.

Download from Www.Somanuals.com. All Manuals Search And Download.

2-5. Video Signal System

2-5-4. Level Adjustment of the VBS Signal

(only when HKCU-951 is installed)

3. Set the VBS LEVEL and the VBS SYNC control on

the EN-145 board panel to their mechanical center.

Then adjust RV201 (VBS GAIN) and RV204 (SYNC)

in the EN-145 board so that the color bar signal has the

specified amplitude.

Adjust the level of the VBS signal output from the unit

using the color bar signal.

Use the switch on the EN-145 board (HKCU-951) and the

control on the panel of the unit for adjustment.

Measurement point : VBS OUT connector on the

HDCU rear panel

Specifications :

A = 100 1 IRE [for NTSC]

A = 700 7 mV p-p [for PAL]

(VBS LEVEL control)

How to adjust using the EN-145 board (HKCU-

951) of the unit

B = 40.0 0.4 IRE [for NTSC]

B = 300 3 mV p-p [for PAL]

(VBS SYNC control)

[for NTSC]

[for PAL]

RV204

RV201

Adjust the VBS CHROMA control on the EN-145 board

panel until every spots of the color bar signal fall into the

specified locations “4” on vectorscope.

[for NTSC]

[for PAL]

S107

VBS LEVEL control

VBS SYNC control

VBS CHROMA control

EN-145 board (A side/panel side)

1. Check the switch S107-3 on the EN-145 board to OFF.

Factory setting : OFF

2. Press the BARS button of the MSU-700A/750, RCP-

700 series, etc. to display the color bars on the wave-

form or vector monitor.

HDCU-950 IMM

2-17 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

2-5. Video Signal System

2-5-5. Adjusting the Level of Signals for

Waveform Monitor

How to adjust using the VCS-700

In the system with the MSU-700A/750, CNU-700/500 or

VCS-700, the video output signal of the unit can be

checked on the waveform or vector monitor connected to

the WF A OUTPUT connector and the WF B OUTPUT

connector of the VCS-700.

Connect the WF OUT connector of the DIF-124 board to

the WF 1 connector of the VCS-700 and connect the PIX

OUT connector to the PIX 1 connector. Then adjust the

signal level using the color bar signal.

The video output signal of the unit can be checked on the

waveform monitor connected to the WF OUT connector.

Adjust the WF output signal level using the color bar

signal.

In the system with the MSU-700A/750, CNU-700/500 or

VCS-700, the video output signal can be checked on the

waveform monitor connected to the VCS-700.

1. Press the BARS button of the MSU-700A/750, RCP-

740/741, etc., or press the ENC button of the WAVE-

FORM MONITOR buttons (or MONITOR SELECT

buttons) to display the color bars on the waveform or

vector monitor.

Adjusting the WF Output Signal Level

How to adjust on the RC-91 board of the unit

2. Set the CONTROL switch of the VCS-700 to RESET.

3. Adjust the color bars signal using the WFM 1 LEVEL

and WFM 1 CHROMA controls of the VCS-700 so

that it is within the specified level.

RV305

RV301

Measurement point : PIX OUT connector on the VCS-

700

Specification :

A = 100 1 IRE [for NTSC]

A = 700 7 mV p-p [for PAL]

(WFM 1 LEVEL control)

[for NTSC]

[for PAL]

RC-91 board (A side)

1. Press the BARS button of the MSU-700A/750, RCP-

740/741, etc., or press the ENC button of the WAVE-

FORM MONITOR buttons (or MONITOR SELECT

buttons) to display the color bars on the waveform

monitor.

2. Adjust the color bar signal using control RV301

(WFM GAIN) and RV305 (WF CHROMA) on the

RC-91 board so that it is within the specified level.

Measurement point : WF OUT connector on the

HDCU rear panel

Each luminescent spot on the vector monitor must be

within the “4” range.

(WFM 1 CHROMA control)

Specification :

A = 100 1 IRE [for NTSC]

A = 700 7 mVp-p [for PAL]

[for NTSC]

[for PAL]

[for NTSC]

[for PAL]

HDCU-950 IMM

2-18 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

2-5. Video Signal System

How to adjust using the MSU-700A/750

Each luminescent spot on the vector monitor must be

The signal level can be adjusted by using the MSU-700A/

750 instead of using the controls of the VCS-700.

within the “4” range.

(WF Chroma)

[for NTSC]

[for PAL]

1. Press the MAINTENANCE button of the MODE

block of the MSU-700A/750 so that the button lights.

The maintenance menu is displayed.

Exit

Maintenance Menu

Auto

Setup

CAM SW

Setting

Adjusting

Lens

VCS

Adjusting Adjusting

Adjusting

SuperMotion

Setting

Adjusting the Staircase Signal

Adjust the staircase signal to display signals in the sequen-

tial mode on the waveform monitor. If the signal of the

sequential mode is not normally displayed on the wave-

form monitor, perform this adjustment.

When the waveform monitor is connected to the unit,

perform the adjustment using controls RV303 (STAIR

STEP POSITION) and RV304 (STAIR STEP LEVEL) on

the RC-91 board panel of the unit. When the VCS-700 is

connected, refer to the VCS-700 Maintenance Manual.

2. Press [VCS|Adjusting].

The VCS monitor level adjustment item menu is

displayed.

Clear

Home

Monitor

Level

RV303

RV304

VCS Monitor Level

Middle High 100%

S301

Chara-

cter on

Low

WF Level WF Chroma

3. Adjust the color bars signal of the WF Level and WF

Chroma so that it is within the specified level.

Measurement point : PIX OUT connector on the VCS-

700

Specification :

A = 100 1 IRE [for NTSC]

A = 700 7 mV p-p [for PAL]

(WF Level)

RC-91 board (A side)

[for NTSC]

[for PAL]

1. Press the SEQ button of the WAVEFORM MONITOR

buttons (or MONITOR SELECT buttons) of the MSU-

700A/750, RCP-740/741, etc.

2. Adjust the position of the signal to be displayed using

control RV303 (STAIR STEP POSITION) on the RC-

91 board.

3. Use control RV304 (STAIR STEP LEVEL) on the

RC-91 board so that the intervals of signals A and B to

be displayed are almost equal.

HDCU-950 IMM

2-19 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

2-5. Video Signal System

Press the SEQ button of the WAVEFORM MONITOR

button (or the MONITOR SELECT button) of the MSU-

700A/750, RCP-740/741, etc., to output the waveform

monitor control signal of the unit, synchronizing with the

output signal of the WF OUT connector.

The control method of the sequential mode depends on the

waveform monitor used. If required, change the polarity of

the control from the setting of switch S301 (SEQ) on the

RC-91 board.

If adjustment is not possible even after the polarity is

changed, perform the adjustment on the waveform monitor

side.

HDCU-950 IMM

2-20 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

2-5. Video Signal System

2-5-6. Adjusting the Level of Signals for

Picture Monitor

How to adjust using the VCS-700

In the system with the MSU-700A/750, CNU-700/500 or

VCS-700, the video output signal of the unit can be

checked on the waveform or vector monitor connected to

the PIX A OUTPUT and PIX B OUTPUT connectors of

the VCS-700.

Connect the PIX OUT connector of the DIF-124 board to

the PIX 1 connector of the VCS-700 using the color bars

signal.

The video output signal can be checked on the waveform

or vector monitor connected to the PIX OUT connector.

Use the color bars to adjust the level of the PIX output

signal.

In addition, in the system with the MSU-700A/750, CNU-

700/500 or VCS-700, the video signal of the unit can be

checked on the waveform or vector monitor connected to

the VCS-700.

1. Press the BARS button of the MSU-700A/750, RCP-

740/741, etc., or press the ENC button of the WAVE-

FORM MONITOR buttons (or MONITOR SELECT

buttons) to display the color bars on the waveform or

vector monitor.

How to adjust on the RC-91 board of the unit

2. Adjust the color bars signal using the PIX 1 LEVEL

and PIX 1 CHROMA controls on the VCR-700 board

so that it is within the specified level.

RV302

Measurement point : PIX OUT connector on the VCS-

700

Specification :

A = 100 1 IRE [for NTSC]

A = 700 7 mV p-p [for PAL]

(PIX 1 LEVEL control)

[for NTSC]

[for PAL]

RC-91 board (A side)

1. Press the BARS button of the MSU-700A/750, RCP-

740/741, etc., and press the ENC button of the PIC-

TURE MONITOR buttons (or MONITOR SELECT

buttons) to display the color bars on the waveform

monitor.

2. Adjust the color bar signal using control RV302 (PIX

GAIN) on the RC-91 board so that it is within the

specified level.

Each luminescent spot on the vector monitor must be

within the “4” range.

(PIX 1 CHROMA control)

[for NTSC]

[for PAL]

Measurement point : PIX OUT connector on the

HDCU rear panel

Specification :

A = 100 1 IRE [for NTSC]

A = 700 7 mV p-p [for PAL]

[for NTSC]

[for PAL]

HDCU-950 IMM

2-21 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

2-5. Video Signal System

2-5-7. Setting the RET Input

Setting the Aspect Ratio for Up-conversion

Set format of the return signal that is input to RET 1 to

RET 3 connectors on the rear panel of this unit.

Set the desired aspect ratio using the switch on the DTX-1

boards.

When the RETURN SET switch on the DTX-1 board panel

is set to SD for setting the return signal format, set the

aspect ratio for up-conversion to each return input.

The aspect ratio also can be set on the maintenance menu

or the configuration menu of the MSU-700A/750. For

more details, refer to the System Manual.

Setup switch : S603 and S604 on the DTX-1 board

(Factory setting : All OFF)

S603-1, -2 : RET 1

S603-3, -4 : RET 2

S603-5, -6 : RET 3

Setting Format of the Return Signal

S603-7, -8 : PROMPTER (RET 4)

Setup switch : RETURN SET switch (S605) on the DTX-1

panel (Factory setting : REM)

HD : When HD-SDI signal is input as return signal.

SD : When SD-SDI or analog VBS signal is input as

return signal.^*

S603-1, -3, -5, -7 S603-2, -4, -6, -8

Aspect ratio

Letter box^*1

Edge-crop^*1

Squeeze^*1

OFF

REM :When the reference is set from RM/MSU or a

device that is connected outside.

OFF

It is interlocked with

the down conversion

aspect ratio of the

RC-91 board output.

* : To select either the SD-SDI or analog VBS signal, set the switch S601

on the DTX-1 board. For details, refer to Section 1-6-5. “Setting of

Switches on Boards _ DTX-1 Board”.

*1 Letter box : The HD video signal of 16 : 9 (or aspect ratio set with S604

on the DTX-1 board) is inserted into the picture frame of 4 :

3 as it is and converted to the SD signal. (4 : 3) (The black

level is inserted into the top and bottom of the picture.)

Edge-crop : Video signal as large as 4 : 3 is cut from the HD video signal

and is converted to the SD signal. (4 : 3)

When the PROMPTER connector on the rear panel of this

unit is used as RET 4, set the switch S607-2 on the DTX-1

board to OFF.

Squeeze : The HD video signal of 16 : 9 is converted to the SD signal

as it is. (16 : 9)

For details, refer to Section 1-6-5. “Setting of Switches on

Boards _ DTX-1 Board”.

S604-1, -2 : RET 1

S604-3, -4 : RET 2

S604-5, -6 : RET 3

S604-7, -8 : PROMPTER (RET 4)

S601

S604-1, -3, -5, -7

S604-2, -4, -6, -8

Aspect ratio

S604

S603

S605

13 : 9

14 : 9

15 : 9

16 : 9

OFF

RETURN SET switch

DTX-1 board (A side/panel side)

HDCU-950 IMM

2-22 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

2-5. Video Signal System

How to set the aspect ratio

1. Set RETURN SET switch on the DTX-1 board panel to SD.

2. Set the switch S601 (SD RETURN FORMAT) on the DTX-1 board, to SDI.

3. Set S603 (SD RET ASPECT) and S604 (LB ASPECT) on the DTX-1 board according to the desired

aspect ratio.

For more details, refer to Section 1-6-5, “Setting of Switches on Boards_DTX-1 Board”.

Examples of display

RETURN VIDEO input picture

Picture on the HDC-950/930 viewfinder

Edge-crop

S603-1, -3, -5, -7/DTX-1 → ON

The rightmost end and the leftmost end are

cut and replaced by black on the viewfinder.

S603-2, -4, -6, -8/DTX-1 → OFF

Squeeze

S603-1, -3, -5, -7/DTX-1 → OFF

S603-2, -4, -6, -8/DTX-1 → ON

The same picture as the camera output

picture is shown.

Letter box

Letter box (16 : 9)

S603-1 to -8/DTX-1 → ON

S604-1 to -8/DTX-1 → OFF

The same picture as the camera output

picture is shown.

HDCU-950 IMM

2-23 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

2-5. Video Signal System

Edge-crop

Semi-letter box (15 : 9)

When the signal was up-converted in the edge-crop

mode

S603-1 to -8/DTX-1 → ON

S604-1, -3, -5, -7/DTX-1 → OFF

S604-2, -4, -6, -8/DTX-1 → ON

Edge-crop

Semi-letter box (14 : 9)

When the signal was up-converted in the edge-crop

mode

S603-1 to -8/DTX-1 → ON

S604-1, -3, -5, -7/DTX-1 → ON

S604-2, -4, -6, -8/DTX-1 → OFF

Edge-crop

Semi-letter box (13 : 9)

S603-1 to -8/DTX-1 → ON

S604-1 to -8/DTX-1 → ON

When the signal was up-converted in the edge-crop

mode

HDCU-950 IMM

2-24 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

2-5. Video Signal System

Setting the Frame Frequency Conversion

When the HKCU-953 is installed and the operation frame

frequency of the camera is set to 24F (24PsF), set the

frame frequency conversion of the return signal.

Setup switch : S606 on the DTX-1 board

(Factory setting : All OFF)

S606-1, -2 : RET 1

S606-3, -4 : RET 2

S606-5, -6 : RET 3

S606-7, -8 : PROMPTER (RET 4)

S603-1, -3, S603-2, -4,

Type of the frame

conversion

-5, -7

-6, -8

THROUGH :

Frame frequency is not

converted.

OFF

A (24PsF conversion) :

When the camera is 24PsF,

the forced-reverse conversion

is performed. (Conversion to

reconstruct 24PsF)

OFF

B (48i conversion) :

When the camera is 24PsF,

the forced-reverse conversion

is perfomed. (Conversion to

48i format by simple skipping)

OFF

AUTO :

Depends on the setting of

S1-1 on the FC-88 board.

Setup switch : S610 on the DTX-1 board

(Factory setting : 0)

You can set phase of the frame frequency conversion

manually. For details, refer to Section 1-6-5. “Setting of

Switches on Boards _ DTX-1 Board”.

HDCU-950 IMM

2-25 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

2-6. Note on Using the Large Lens Adapter CA-905L

When attaching the large lens adapter CA-905L to the camera to be connected to the HDCU-950, note the

following.

Viewfinder

Use of the 6-type color LCD viewfinder HDVF-C700W is recommended.

Because the 7-type B/W viewfinder HDVF-700A consumes a large amount of power, the maximum

camera cable length in this case is limited to 300 meters.

Note that the 7-type color viewfinder HDVF-7700 cannot be used with the HDCU-950.

Lens

If you want to use a lens (such as a vibration-proof lens or high-magnification lens) which consumes a

large current, it is recommended to operate the lens on an external power supply.

The power consumption for a lens that draws a large current increases for the time being when using the

lens. If the power for the lens is supplied from the camera, the power to the camera may be stopped if the

protection circuit detects a voltage drop in case of using a long cable.

Utility Power Supply

The HDCU-950 supplies power to the camera at DC 180 V. Therefore, the utility power outlet of the

large lens adapter CA-905L cannot be used.

HDCU-950 IMM

2-26 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

Section 3

Service Overview

3-1. Cleaning of Connector/Cable

Cleaning

Before connecting the unit to the camera, it is recommend-

ed to clean the following optical contact portions.

. CAMERA connector of the unit

Male connector

Clean the tip of the white optical contacts by a cotton swab

moistened with alcohol.

. CCU connector of the camera side

. Optical/electrical cable

Optical contacts (white)

Follow the procedures below for cleaning.

Tools Required

. Alignment sleeve remover HC-001

(for female connector)

Sony P/N : J-6480-010-A

Female connector

Insert the shorter nose end when removing/installing the

alignment sleeve.

Grasp not the shock absorber portion of the remover but

the handle in use.

The optical contacts for female connector are in an unex-

posed state. In cleaning, it is necessary to be exposed by

removing the alignment sleeve in advance. Proceed as

follows.

1. Insert the alignment sleeve remover into the alignment

sleeve in the straight line and turn it clockwise.

Shock absorber

Handle

Alignment sleeve

Use the shorter nose end.

. Cotton swabs (commercially available)

Use a cotton swab whose diameter is about 4 mm.

If a cotton swab whose diameter exceeds 5 mm is used,

the cotton swab cannot be inserted into the end of the

connector and the tip of the optical contact cannot be

cleaned.

Alignment sleeve remover

HDCU-950 IMM

3-1 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

3-1. Cleaning of Connector/Cable

3-2. Recommended Replacement Parts

2. When the turn stops, pull out the remover in the

straight line forcedly.

3-2. Recommended Replacement Parts

3-2-1. Power Fan

The alignment sleeve can be removed/reinstalled with

the sleeve itself attached to the tip of the remover.

Great care should be taken so as not to lose or damage

the alignment sleeve.

The recommended replacement fan should be used in the

switching regulator of this unit.

The lifespan of the fan is about 30,000 hours, which means

that the fan can be used for about three and a half years if

the power is on all the time, so the fan should be replaced

according to service conditons.

(Alignment sleeve: Sony P/N 9-980-074-01)

Alignment sleeve

For the replacement procedure, refer to the separately

available maintenance manual.

Replacement Part

Part :

Power fun

Part No. : 9-885-022-85

3. Clean the tip of the white optical contacts by a cotton

swab moistened with alcohol.

Optical contacts (white)

4. Insert the remover with the alignment sleeve attached

to its tip, and push it until it clicks.

5. Rotate the remover counterclockwise to install the

alignment sleeve, and extract the remover.

HDCU-950 IMM

3-2 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

3-3. Character Display Function

The contents of the pages displayed on the HD monitor (or

SD analog monitor) are as follows.

This unit has the built-in character generation circuit. The

character information such as the settings, state and self-

diagnosis of the unit can be mixed with the HD SDI video

signal and the SD video signal. The mixed signal can be

output from the MONI OUT (DRX-1 board output) and the

PIX OUT (RC-91 board output) connector respectively.

They can be displayed on the HD monitor and the SD

analog monitor.

Page

Title

Displays OFF (CHARACTER button

OFF)

Camera Lens/Filter Status

Camera Status

System Status

Diagnosis

The character MIX function can be forcibly turned OFF by

turning OFF S206-4 (HD SDI) on the DRX-1 board or

S10-8 (SD SDI) on the RC-91 board.

System Diag 1/3

System Diag 2/3

System Diag 3/3

AT Diag

Operating procedure

AVP Diag

In order to show the setting, the state and the self-diagnosis

display on the HD monitor and the SD analog monitor,

press the CHARACTER button of the RCP so that the

button lights, or operate the CHARACTER switch on the

panel surface of the DRX-1 board.

To change the page, press the CHARACTER button of the

RCP. The page can also be changed by pressing the

CHARACTER switch on the panel surface of the DRX-1

board panel.

12-1

12-2

13-1

13-2

DTX Diag

DRX Diag

Slot-5 Diag (RC-91/DIF-124 Board)

Slot-5 Diag (FC-88/SDI-73 Board)

Slot-6 Diag (EN-145/VDA-61 Board)

Slot-6 Diag (RC-91/DIF-124 Board)

ROM Version

When the CHARACTER button of the RCP (or CHAR-

ACTER switch on the panel surface of the DRX-1 board)

is kept pressed, the pages are changed continuously. After

all the pages are displayed, the cycling display stops on the

final page and the CHARACTER button of the RCP goes

off. To display the character information again, press the

CHARACTER button of the RCP.

Required equipment

. HD monitor

Sony BVM-D20F1J or equivalent

. SD monitor

Sony BVM-1911/2811 or equivalent

. Remote control unit

Sony RCP-700 series

. HDVS camera system

HDC-950/930

The first page is blank. When selecting the first page, the

display of characters is OFF.

S206

S203

S10

CHARACTER switch

DRX-1 board (A side/panel side)

RC-91 board (A side)

HDCU-950 IMM

3-3 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

3-3. Character Display Function

Page 1

Page 3

Camera Lens/Filter Status Display

System Status Display

* System Status *

HDC-950 1080/59.94I

Gen Lock : SD

DRX:1080/59.94I

FC :1080/59.94I

RC : 525/59.94I

RET1:HD SDI 59.94I

2:HD SDI 59.94I

3:HD SDI 59.94I

4:SD VBS SQ

F:CLS

No. Contents

Displays the setting state of the lens extender.

Displays the type of camera connected to the unit.

(HDC-950/HDC-930/UNDEFINED)

Displays the setting state of the ND filter and CC filter.

Displays the type of external sync signal.

(Free/SD/HD)

Displays the message when the optical reception level

lowers.

Displays the setup format of the DRX-1 board.^*1

Displays the setting state of the aperture of the lens.

Displays the setup format of the board mounted in the

fifth slot from the left of the front side.^*1

Displays the setup format of the board mounted in the

sixth (right most) slot from the left of the front side.^*1

Page 2

Camera Status Display

Displays the type of signal that is input to the RET 1

connector on the rear panel of the unit.

Displays the type of signal that is input to the RET 2

connector on the rear panel of the unit.

White

R: 0

G: 0

B: 0

Black

R: 0

G: 0

B: 0

M: 0

Flare

R: 0

G: 0

B: 0

Displays the type of signal that is input to the RET 3

connector on the rear panel of the unit.

BLK

0 OFF

Detail

1 ON

Displays the type of signal that is input to the RET 4

(PROMPTER) connector on the rear panel of the unit.

*1 : For details, refer to Section 2, “System Setup”.

F:CLS

Contents

Displays information of White/Black/Black γ/Flare/Detail, etc.

HDCU-950 IMM

3-4 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

3-3. Character Display Function

Page 4

Page 5

Diagnosis Display

System Diag (1/3) Display

* System Diag 1/3 *

Optical Condition

CAMERA

CCU

* Diagnosis *

AT :OK

AVP:OK

DTX:OK

DRX:OK

FC :OK

RC :OK

Fan Power OK

Timer

264H

No. Contents

Displays the self-diagnosis result of the AT-149 board

(OK/NG).^*2

State of the optical reception level of the camera and

camera control unit (OK/CARE/WARNING/NG)^*3

CARE:

The optical level is _17 to _20 dBm.

Displays the self-diagnosis result of the AVP-4 board

(OK/NG).^*2

WARNING: The optical level is _20 dBm or less.

NG:

The state when the optical level is low and

any signal cannot be obtained.

Displays the self-diagnosis result of the DTX-1 board

(OK/NG).^*2

When either of CARE, WARNING or NG appears on the

CCU side, clean the connector or cable while referring to

Section 3-1. When either of CARE or WARNING or NG

appears on the camera side, clean the connector or cable

while referring to the Maintenances Manual of the camera.

Displays the self-diagnosis result of the DRX-1 board

(OK/NG).^*2

Displays the self-diagnosis result of the board mounted in

the fifth slot from the left of the front side (OK/NG).^*2

State of the fan of the power supply block (OK/NG)

NG : The fan of the switching regulator is defective.

Displays the self-diagnosis result of the board mounted in

the sixth (right most) slot from the left of the front side

(OK/NG).^*2

Displays the accumulated power-on hours to the AT-149

board

*2 : For the contents of the self-diagnosis of each board, refer to pages 8 to

*3 : The optical sending/receiving level state of the main unit also can be

checked using the indicator on the panel surface of the DTX-1 board.

For details, refer to Section 1-7-5. “Functions of the Indicators on the

Boards _ DTX-1 Board”.

14 of the character display.

HDCU-950 IMM

3-5 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

3-3. Character Display Function

Page 6

Page 7

System Diag (2/3) Display

System Diag (3/3) Display

* System Diag 2/3 *

* System Diag 3/3 *

CAMERA Cable Connect

Data OK

Power ON

Intercom

CAMERA CH1 PROD

MIC ON

CH2 PROD

MIC ON

RCP/CNU Cable Connect

Data OK

Power OFF

CAMERA MIC Gain

CH1 60dB Local

CH2 60dB Local

PANEL

Cable Open

Data --

Power ON

No. Contents

State of camera cable connection (Open/Connect)

Setting state of the intercom channel 1 of the camera

side (ENG/PROD)

Existence of data from the camera (__/Wait/Sense/OK)

__ :

The communication with the camera cannot be

established.

Setting state of the intercom channel 2 of the camera

side (ENG/PROD)

Wait : The communication with camera is in the wait

Gain and control state of the microphone circuit of the

camera side (Remote/Local)

state.

Sense : The communication with the camera is being

established.

State of the power supply of the camera (ON/OFF)

State of cable connection of the RCP/CNU connector on

the rear panel of the unit (Open/Connect)

Existence of the data from the RCP/CNU connector on

the rear panel of the unit (__/Wait/Sense/OK)

__ :

The communication with the equipment

connected to the RCP/CNU connector cannot be

established.

Wait : The communication with the equipment

connected to the RCP/CNU connector is in the

wait state.

Sense : The communication with the equipment

connected to the RCP/CNU connector is being

established.

Power is supplied or not to the RCP/CNU connector on

the rear panel.

ON : 30 V power is supplied for RCP.

OFF : Power is turned off.

State of cable connection with the front panel (Open/

Connect)

Existence of the data from the front panel (__/Wait/

Sense/OK)

__ :

The communication with the equipment

connected to the PANEL connector cannot be

established.

Wait : The communication with the equipment

connected to the PANEL connector is in the wait

state.

Sense : The communication with the equipment

connected to the PANEL connector is being

established.

Power is supplied or not to the front RM panel.

ON :

30 V power is supplied for the front panel.

OFF : Power is turned off.

HDCU-950 IMM

3-6 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

3-3. Character Display Function

Page 8

Page 9

AT Diag Display

AVP Diag Display

Displays the details of self-diagnosis of the AT-149 board

of the unit.

Displays the details of self-diagnosis of the AVP-4 board

of the unit.

* AT Diag *

* AVP Diag *

System Frequency 1.001

CHU Format Setting

Remote 1080/59.94I

Ref.H Phase SD Local

HD-SD DLY 90H

Marker Setting Remote

PLD V1.00 Confing Done

AVP Mode

Normal

CCU Mode

Normal

No. Contents

Display of system frequency coefficient (1.001/1.000)^*4

Displays the version of the PLD (IC300 on the AVP-4

board) and the state of the PLD. (Config Done/Config

NG)

Config Done: PLD (IC300 on the AVP-4 board) started

correctly.

Display of Remote/Local state of camera format setting

and setup format

Setting of the reference signal and display of the

Removal/Local state (SD Local/SD Remote/HD Local/HD

Remote)

Config NG: PLD (IC300 on the AVP-4 board) did not

start correctly.

State of the operation mode of the AVP-4 board (Normal/

Test)

Setting state of delay amount (setting of S417 on the AT-

149 board) when converting the format from the HD

signal to SD signal (1 Frame/90H)^*4

Aspect marker added to the monitor signal and state of

modulation chroma removal (setting of S408 on the AT-

149 board) (Local/Remote)^*4

State of the operation mode (setting of S424 on the AT-

149 board)^*5of the AT-141 board (Normal/Test)

*4 : For details, refer to Section 1-6-1. “Setting of Switches on Boards _ AT-

149 Board”.

*5 : Set S424 to all OFF so that it is set to normal mode.

HDCU-950 IMM

3-7 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

3-3. Character Display Function

Page 10

Page 11

DTX Diag Dispaly

DRX Diag Dispaly

Displays the details of self-diagnosis of the DTX-1 board

of the unit.

Displays the details of self-diagnosis of the DRX-1 board

of the unit.

* DTX Diag *

* DRX Diag *

CB Select

Bar-16:9(100%)

Return Setting:Remote

Return Delay :1Field

RET4(VBS)

:ON

Return FC mode:Auto

PLD V1.00 Config Done

DTX Mode

PLD V1.00 Config Done

DRX Mode

Normal

No. Contents

Setting state of S605 on the DTX-1 board (HD/SD/

Remote)^*6

Setting state of the HD output color bar (setting of S205

on the DRX-1 board)^*7

Setting state of the phase (setting of S607-1 on the DTX-

1 board) with the SD return signal during up-conversion

(SYS/MIN)^*6

Displays the state of the PLD (IC401 on the DRX-1

board) version and PLD (Config Done/Config NG)

Config Done : PLD (IC401 on the DRX-1 board) started

correctly.

Config NG: PLD (IC401 on the DRX-1 board) did not

start correctly.

Setting state whether the PROMPTER connector on the

rear panel is used or not with REM4 (setting of S607-2 on

the DTX-1 board) (ON/OFF)^*6

State of the operation mode on the DRX-1 board

(Normal/Test)

State of the frame frequency conversion mode (setting of

S606 on the DTX-1 board) of the return signal (Through/

A/B/Auto)^*6

*7 : For details, refer to Section 1-6-4. “Setting of Switches on Boards _

DRX-1 Board”.

Displays the state of the PLD (IC401 on the DTX-1

board) version and PLD. (Config Done/Config NG)

Config Done :PLD (IC401 on the DTX-1 board) started

correctly.

Config NG : PLD (IC401 on the DTX-1 board) did not

start correctly.

State of the operation mode on the DTX-1 board (Normal/

Test)

*6 : For details, refer to Section 1-6-5. “Setting of Switches on Boards _

DTX-1 Board”.

HDCU-950 IMM

3-8 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

3-3. Character Display Function

Page 12-1

Page 12-2

Slot-5 Diag Dispaly

Displays the details of self-diagnosis of the RC-91 board

when it is mounted in the fifth slot from the left on the

front side of the unit.

Displays the details of self-diagnosis of the FC-88 board

when it is mounted in the fifth slot from the left on the

front side of the unit.

* Slot-5 Diag *

Front: FC

IN :1080/59.94I

* Slot-5 Diag *

Front: RC

Squeeze

OUT :1080/59.94I

PLD V1.00 Config Done

Mode

Sub-Ref:HD 23.97i

Rear: SDI

PLD V1.00 Config Done

Mode

Normal

Rear: DIF

Output-A

Output-B

SD SDI

No. Contents

Displays the aspect ratio conversion mode during down-

conversion.

State of the MAIN INPUT signal format of the frame

converter

Displays the state of the PLD (IC301 and IC504 on the

RC-91 board) version and PLD. (Config Done/Config NG)

Config Done : PLD (IC301 and IC504 on the RC-91

board) started correctly.

Config NG : PLD (IC301 and IC504 on the RC-91

board) did not start correctly.

State of the conversion format of the frame converter

MAIN OUTPUT signal

Displays the state of the PLD (IC301 on the FC-88 board)

version and PLD. (Config Done/Config NG)

Config Done : PLD (IC301 on the FC-88 board) started

correctly.

State of the operation mode on the RC-91 board (Normal/

Test)

Config NG : PLD (IC301 on the FC-88 board) did not

start correctly.

Displays when the DIF-124 board is installed in the rear

correctly.

State of the operation mode on the FC-88 board (Normal/

Test)

Displays the type of signal that is output from the SD SDI

OUT1 connector on the rear panel. (SD SDI/VBS)^*8

Displays the signal format of the reference signal that is

input to the FRAME REF IN connector (Sub-Ref) on the

rear panel (with HKCU-953).

Displays the type of signal that is output from the SD SDI

OUT2 connector on the rear panel. (SD SDI/VBS/MONI

SDI)^*9

Displays when the SDI-73 board is installed in the rear

correctly.

*8 : When the HKCU-951 is installed, set the switch with S103 on the EN-

145 board. When the HKCU-951 is not installed, the switch is fixed to

SD SDI.

For details, refer to Section 1-6-7. “Setting of Switches on Boards _ EN-

145 Board”.

*9 : When S10-1 on the RC-91 board and the HKCU-951 are installed, set

the switch with S104 on the EN-145 board.

For details, refer to Sections 1-6-6 and 1-6-7. “Setting of Switches on

Boards _ RC-91 Board and EN-145 Board”.

HDCU-950 IMM

3-9 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

3-3. Character Display Function

Page 13-1

Page 13-2

Slot-6 Diag Dispaly

Displays the details of self-diagnosis of the EN-145 board

when the EN-145 board is mounted in the sixth slot (right

most) from the left of the front side of the unit.

Displays the details of self-diagnosis of the RC-91 board

when the RC-91 board is mounted in the sixth slot (right

most) from the left of the front side of the unit.

* Slot-6 Diag *

Front: RC

Squeeze

* Slot-6 Diag *

Front: EN

PLD V1.00 Config Done

Mode

PLD V1.00 Config Done

Mode

Normal

Rear: DIF

Output-A

Output-B

Rear: VDA

SD SDI

No. Contents

Displays the state of the PLD (IC310 on the EN-145

board) version and PLD. (Config Done/Config NG)

Config Done : PLD (IC310 on the EN-145 board)

started correctly.

Config NG : PLD (IC310 on the EN-145 board) did not

start correctly.

Displays the aspect ratio conversion mode during down-

conversion.

Displays the state of the PLD (IC301 and IC504 on the

RC-91 board) version and PLD. (Config Done/Config NG)

Config Done : PLD (IC301 and IC504 on the RC-91

board) started correctly.

State of the operation mode on the EN-145 board

(Normal/Test)

Config NG : PLD (IC301 and IC504 on the RC-91

board) did not start correctly.

Displays when the VDA-61 board is mounted in the rear

correctly.

State of the operation mode on the RC-91 board (Normal/

Test)

Displays when the DIF-124 board is installed in the rear

correctly.

Displays the type of signal that is output from the SD SDI

OUT1 connector on the rear panel. (SD SDI/VBS)^*10

Displays the type of signal that is output from the SD SDI

OUT2 connector on the rear panel. (SD SDI/VBS/MONI

SDI)^*11

*10 :When the HKCU-951 is installed, set the switch with S103 on the EN-

145 board. When the HKCU-951 is not installed, the switch is fixed to

SD SDI.

For details, refer to Section 1-6-7. “Setting of Switches on Boards _

EN-145 Board”.

*11 :When S10-1 on the RC-91 board and the HKCU-951 are installed, set

the switch with S104 on the EN-145 board.

For details, refer to Sections 1-6-6 and 1-6-7. “Setting of Switches on

Boards _ RC-91 Board and EN-145 Board”.

HDCU-950 IMM

3-10 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

3-3. Character Display Function

Page 14

ROM Version Dispaly

Displays the ROM versions of the unit and the peripheral

equipment of the unit.

* ROM Version *

CHU HDC-950

CCU HDCU-950

1.20DM01

1.02

MSU MSU-700A/750

1.10

No. Contents

Displays the ROM version of the camera.

Displays the ROM (IC510 and IC553 on the AT-149

board) version of the HDCU-950.

Displays the ROM version of the equipment that is

connected to the RCP/CNU connector on the rear panel

of he HDCU-950.

HDCU-950 IMM

3-11 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

SAFETY CHECK-OUT

After correcting the original service problem,

perform the following safety checks before

releasing the set to the customer :

The material contained in this manual consists of

information that is the property of Sony Corporation.

Sony Corporation expressly prohibits the duplication of

any portion of this manual or the use thereof for any

purpose other than the operation or maintenance of the

equipment described in this manual without the express

written permission of Sony Corporation.

Check the metal trim, “metallized” knobs,

screws, and all other exposed metal parts for AC

leakage. Check leakage as described below.

LEAKAGE TEST

The AC leakage from any exposed metal part to

earth ground and from all exposed metal parts to

any exposed metal part having a return to

chassis, must not exceed 3.5 mA. Leakage

current can be measured by any one of three

methods.

Le matériel contenu dans ce manuel consiste en

informations qui sont la propriété de Sony Corporation.

Sony Corporation interdit formellement la copie de

quelque partie que ce soit de ce manuel ou son emploi

pour tout autre but que des opérations ou entretiens de

l’équipement à moins d’une permission écrite de Sony

Corporation.

1. A commercial leakage tester, such as the

Simpson 229 or RCA WT-540A. Follow the

manufacturers’ instructions to use these

instruments.

Das in dieser Anleitung enthaltene Material besteht aus

Informationen, die Eigentum der Sony Corporation sind.

Die Sony Corporation untersagt ausdrücklich die

Vervielfältigung jeglicher Teile dieser Anleitung oder den

Gebrauch derselben für irgendeinen anderen Zweck als

die Bedienung oder Wartung der in dieser Anleitung

2. A battery-operated AC milliammeter. The

Data Precision 245 digital multimeter is

suitable for this job.

3. Measuring the voltage drop across a resistor

by means of a VOM or battery-operated AC

voltmeter. The “limit” indication is 5.25 V, so

analog meters must have an accurate low-

voltage scale. The Simpson 250 and Sanwa

SH-63Trd are examples of a passive VOM

that is suitable. Nearly all battery operated

digital multimeters that have a 20 V AC range

are suitable. (See Fig. A)

beschriebenen

Ausrüstung

ohne

ausdrückliche

schriftliche Erlaubnis der Sony Corporation.

To Exposed Metal

Parts on Set

voltmeter

(5.25V)

0.15 µF

1.5 kZ

Earth Ground

Fig A. Using an AC voltmeter to check AC leakage.

HDCU-950 IMM

Download from Www.Somanuals.com. All Manuals Search And Download.

Printed in Japan

2003. 6 16

Sony Corporation

HDCU-950 (SY) J, E

3-619-324-04

B&P Company

Download from Www.Somanuals.com. All Manuals Search And Download.

Servis Rhino Lawn Mower CY84 User Manual
Sharp Speaker HTSB350 User Manual
Singer CD Player ACC 31 User Manual
Singer Sewing Machine 11 29 User Manual
Smooth Fitness Bicycle RB5 User Manual
Sony Camcorder Accessories MPK TRV2 User Manual
Standard Horizon Fish Finder CPF180I User Manual
Sterling Plumbing Outdoor Shower 71140112 User Manual
Sylvania Flat Panel Television 6620LF4 User Manual
Sylvania Flat Panel Television LD427SSX User Manual