4-674-967-11(1)
Operating Instructions
Mode d’emploi
Wireless LAN PC Card
(IEEE 802.11g: 2.4 GHz/54 Mbps)
PCWA-C300S
© 2003 Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC RF Exposure
•
Le terme “IC” avant le muméro d’homologation
ne signifie seulement que les normes d’Industrie
du Canada ont été respectées.
Install and connect this product by following
descriptions in its Operating Instructions before
using it.
About the supplied software
This equipment generates and radiates radio
frequency energy.
THE SUPPLIED SOFTWARE IS SUPPLIED
PURSUANT TO THE APPLICABLE END-
USER LICENSE AGREEMENT.
SAR (Specific Absorption Rate) for this device
was measured in accordance with
FCC OET Bulletin 65. Supplement C and
guidelines established in IEEE C95.1-1991.
•
•
•
Copyright laws prohibit reproducing the
software or the software manual in whole or in
part, or renting the software without the
permission of the copyright holder.
In order to comply with FCC RF exposure limits
please maintain at least 4 mm (0.16 in.) spacing
between the user and the antenna of this device
while it is in use.
In no event will SONY be liable for any
financial damage or loss of profits, including
claims made by third parties, arising out of the
use of the software supplied with this product.
In the event a problem occurs with this software
as a result of defective manufacturing, SONY
will replace it at SONY’s option or issue a
refund; however, SONY bears no other
responsibility.
This product can only be used with desktop
computers and laptop (notebook) computers with
side mounted PCMCIA slots.
This device cannot be used with other types of
host devices, such as PDAs.
Users are not permitted to make changes or
modify the system in any way.
•
•
The software provided with this product cannot
be used with equipment other than that which is
designated for use with.
Please note that, due to continued efforts to
improve quality, the software specifications
may be changed without notice.
For customers in Canada
•
This class B digital apparatus complies with
Canadian ICES-003.
•
Operation is subject to the following two
conditions; (1) this device may not cause
interference, and (2) this device must accept
any interference, including interference that
may cause undesired operation of the device.
Program © 2001, 2002, 2003 Sony Corporation,
© 2000-2003 Atheros Communications, Inc., All
Rights Reserved
•
•
To prevent radio interference to the licensed
service, this device is intended to be operated
indoors and away from windows to provide
maximum shielding. Equipment (or its transmit
antenna) that is installed outdoors is subject to
licensing.
Documentation © 2003 Sony Corporation
Sony, VAIO,
,
, and the
Eco Info logo are trademarks of Sony
Corporation.
The term “IC” before the equipment
certification number only signifies that Industry
Canada technical specifications were met.
Microsoft and Windows are registered trademarks
of Microsoft Corporation in the United States of
America and/or other countries.
Pour les utilisateurs au Canada
Cet appareil numérique de la classe B est
conforme à la norme NMB-003 du Canada.
L’utilisation de ce dispositif est autorisée
seulement aux conditions suivantes : (1) il ne
doit pas produire de brouillage et (2)
MMX and Pentium are registered trademarks of
Intel Corporation.
•
All other trademarks are trademarks of their
respective owners.
•
l'utilisateur du dispositif doit être prêt à
accepter tout brouillage radioélectrique reçu,
même si ce brouillage est susceptible de
compromettre le fonctionnement du dispositif.
•
Pour empêcher que cet appareil cause du
brouillage au service faisant l'objet d'une
licence, il doit être utilisé à l’intérieur et devrait
être placé loin des fenêtres afin de fournir un
écran de blindage maximal. Si le matériel (ou
son antenne d’émission) est installé à
l’extérieur, il doit faire l'objet d'une licence.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of contents
Overview ................................................ 5
Capabilities..................................... 5
System requirements ...................... 8
Documentation and Help file................ 10
Additional information
Manually installing, verifying, and
removing the supplied software ....... 31
Installing the Wireless LAN PC Card
driver manually......................... 31
Installing the Wireless Panel
Getting started
manually ................................... 39
Unpacking............................................. 12
Supplied software ......................... 12
Installing the supplied software ............ 13
Connecting to the Access Point with
Wireless Panel (Windows Me/
2000 operating system)............. 41
Making Access Point Connection
Verifying Wireless LAN PC Card
driver installation ...................... 42
Settings ............................................ 20
Windows Me or Windows 2000
operating system ....................... 20
Uninstalling the Wireless LAN PC
Card driver ................................ 50
Windows XP operating system .... 24
Uninstalling the Wireless Panel ... 53
Precautions ........................................... 56
Specifications ....................................... 57
Getting help .......................................... 57
Glossary ................................................ 58
Troubleshooting.................................... 60
Removing the Wireless LAN PC Card and
Precautions When Inserting it .......... 28
To remove the Wireless LAN PC
Card .......................................... 28
If your computer has two PC Card
slots ........................................... 28
Wireless LAN connection
Checking the communication status ..... 29
Checking the wireless signal
strength ..................................... 29
Checking network information .... 29
Using the Wireless Panel ...................... 30
Opening the Wireless Panel ......... 30
•
•
•
In this manual, Microsoft® Windows® Millennium Edition is referred to as Windows Me.
In this manual, Microsoft® Windows® 2000 Professional is referred to as Windows 2000.
In this manual, Microsoft® Windows® XP Professional and Microsoft® Windows® XP Home Edition are
referred to as Windows XP.
Notes
•
•
The user interface of the Sony supplied software may differ slightly from that shown in this manual.
This manual is written based on the assumption that you are familiar with basic operations of the
Windows operating system. For computer operations, refer to manuals that come with your computer.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview
Capabilities
The Wireless LAN PC Card (IEEE 802.11g: 2.4 GHz/54 Mbps)
PCWA-C300S is a PC Card type wireless network card. With this card, you
can build a wireless LAN, allowing multiple computers to communicate
and exchange data without needing any physical connection. The supplied
Wireless Panel software lets you easily configure the card for multiple
networks. For example, you can store different settings required for
networking at the office and at home, or quickly switch between Access
Point (Infrastructure) Network connection mode and Peer to Peer (Ad-Hoc)
Network connection mode. This greatly facilitates use of the card in various
environments and for a range of applications.
z Hints
• The network mode can easily be switched using the supplied Wireless Panel software.
• To use the card in Access Point Network connection mode, an IEEE 802.11g or IEEE
802.11b compliant Wireless LAN Access Point* (available separately) is necessary.
With the Windows Me or Windows 2000 operating system:
Access Point (Infrastructure) Network
connection mode
Peer to Peer (Ad-Hoc) Network
connection mode
*
If using the separately available Wireless LAN Access Point PCWA-A320, also refer to
the documentation supplied with the unit.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
With the Windows XP operating system:
Available Wireless Networks
Windows XP Service Pack 1:
Available Wireless Networks
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessing the Internet from various points within your
home (Access Point Network connection mode)
With a separately available Access Point you can easily build a wireless
network. By connecting a DSL modem, cable modem, or ISDN router to
the Access Point, you can access the Internet from the living room,
bedroom, or any other convenient location in the house. Equipping multiple
computers with a Wireless LAN PC Card also allows you to exchange files
between the computers via the Access Point.
ADSL modem
etc.
z Hint
The illustration above gives an example of a system configuration using the Access Point
Network connection mode. Two computers equipped with Wireless LAN PC Cards
establish communications with the Wireless Broadband Router PCWA-AR300. The
Wireless Broadband Router is connected to the ADSL modem, therefore it is possible to
access the Internet through this wireless connection.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Direct communication between computers
(Peer to Peer Network connection mode)
The Peer to Peer Network connection mode enables computers equipped
with Wireless LAN PC Cards to communicate directly. This allows file
sharing in locations where the Wireless LAN Access Point is not present.
System requirements
To use the supplied software, the following system requirements must be
met:
❑Windows®-compatible PC:
– 128 MB RAM or more
– Card Bus compliant PC Card slot
– CD-ROM drive (for software installation)
❑Operating system:
– Microsoft® Windows® Millennium Edition
– Microsoft® Windows® 2000 Professional
– Microsoft® Windows® XP Home Edition
– Microsoft® Windows® XP Professional
❑Display:
High color (16-bit color) or higher, 800 × 480 pixels or higher
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
• Correct operation is not assured for all computers, even if satisfying the above system
requirements.
• Correct operation in an OS upgrade environment is not assured, except for factory
provided Windows XP operating system upgrade packages for Sony VAIO® series
computers.
• For Internet access via the wireless LAN, an IEEE 802.11g or IEEE 802.11b compliant
Wireless LAN Access Point (available separately) is necessary.
• An Internet Service Provider (ISP) is required for Internet access.
Precaution when using the PCWA-C300S
Because of the particular shape of the PCWA-C300S, it may not be possible to insert
it into all computers.
The antenna is obstructed. The
PCWA-C300S cannot be inserted.
1 The PCWA-C300S has an antenna
protruding up 0.4 in. (9 mm). If
obstructions 0.6 in. (15 mm) in length or
more come in contact with it when you
insert the PCWA-C300S into the PC card
slot, you cannot fully insert the wireless
LAN PC card into the slot.
Computer
Wireless LAN PC Card PCWA-C300S
The PC card slot is longer than
3.3 in. (85 mm). The PCWA-C300S
cannot be inserted.
2 If the PC card slot of your computer is
more than 3.3 in. (85 mm) in length, you
cannot fully insert the PCWA-C300S into
the slot.
Computer
Wireless LAN PC Card PCWA-C300S
For details, visit
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Documentation and Help file
This product comes with the following documentation and help files.
❑Operating Instructions (this document)
Explains how to install the Wireless LAN PC Card and how to configure
all settings of the card.
❑Quick Start Guide
This document explains how to install software required to use the
Wireless LAN PC Card (IEEE 802.11g: 2.4 GHz/54 Mbps)
PCWA-C300S. The document also contains answers to frequently asked
questions and common problems.
❑Wireless Panel Online Help
This is the Online Help of the supplied Wireless Panel software. Refer to
it for instructions on how to use the software.
Access the Wireless Panel Online Help as follows.
❑ Access from the Easy Installation Wizard
1
On the main menu of the Easy Installation Wizard, click
“Documents”.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
2
On the screen that opens, click “Wireless Panel Online Help”.
❑ Access from Wireless Panel
1
Install the Wireless Panel software, following the instructions in this
manual.
2
3
Start the Wireless Panel.
Right-click the Wireless Panel icon on your Windows operating
system taskbar and click Help on the shortcut menu.
z Hint
You can also access Help by clicking
on the Wireless Panel title bar.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking
Your Wireless LAN PC Card comes with the following items:
• Wireless LAN PC Card
• CD-ROM (Setup disc)
• Quick Start Guide
• Operating Instructions
• Warranty card
Supplied software
The supplied CD-ROM contains the following software.
❑Wireless LAN PC Card driver
This device driver is necessary to the operation of the Wireless LAN PC
Card.
❑Wireless Panel
Wireless Panel is a utility software that lets you configure the computer
for the wireless LAN and monitor the communication status. The
software is also used to switch between networks.
Normally, the Wireless Panel appears as an icon on your Windows
operating system taskbar, which shows the communication status.
When using the card for the first time, see page 13 for
information on how to install the Wireless LAN PC Card driver
and the Wireless Panel.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the supplied software
This section explains how to use the supplied CD-ROM to install the
Wireless LAN PC Card device driver and Wireless Panel. You must insert
the Wireless LAN PC Card into your computer before installing the device
driver and Wireless Panel.
The installation procedures are performed with an easy-to-use wizard.
Before you start, verify the following.
• The wizard located on the CD-ROM supplied with the Wireless LAN PC
Card. Make sure that your CD-ROM drive is ready for use.
• When using the Wireless LAN PC Card in Access Point Network
Connection mode, you must install the Access Point and make the
necessary settings before proceeding. For details about these procedures,
refer to your Access Point user’s guide.
Notes
• To install the supplied software on a computer running the Windows 2000 operating
system, log on with a user account listed in “Administrators”. To install the supplied
software on a computer running the Windows XP operating system, log on with a user
account with administrator access privileges. You cannot install the software or modify
settings when logged on with any other account.
• To change any of the Wireless Panel settings on a computer running the Windows 2000
operating system, log on with a user account listed in “Administrators”. You cannot
modify settings when logged on with any other account.
• Exit all other Windows operating system programs.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Important
Computer Firewall Functions
When using the Windows XP “Internet Connection Firewall” function
Enabling the Windows XP “Internet Connection Firewall” function may prevent
you from being able to access your computer through wireless communication. (This
function is inactive under the Windows XP operating system default settings.)
Because of this function, you may not be able to connect to your network when you
change your Access Point settings. If this happens, deactivate the “Internet
Connection Firewall” function, connect to the network, and then reactivate the
function. For details, refer to Windows XP Help.
Note
Network security is an important issue. You are urged to consider carefully how best to protect your
computer.
When using a personal firewall function provided by virus scanning
or network security software
Virus scanning and network security software sometimes includes a function called
a “personal firewall” that is designed to prevent illegal access by outside entities.
Depending on the software, the security level of this function may be initially set to
a high level. If this high security level setting is left in effect, it may be impossible
for an outside entity to access your computer. This can cause problems such as not
being able to connect to the network when changing the Access Point’s settings. In
this event, lower the security level in order to permit the network connection. For
details, refer to the manuals provided with your software.
Notes
•
•
Pay special attention to security issues.
For questions regarding firewall functions, please contact your firewall software manufacturer.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
1 When using the Wireless LAN PC Card in Access Point
Network Connection mode, turn on the Access Point.
2 Insert the supplied CD-ROM into the CD-ROM drive of your
computer.
The Easy Installation Wizard starts automatically.
z Hint
If the Easy Installation Wizard does not appear when you insert the supplied
CD-ROM into your CD-ROM drive, double-click “Setup.exe” (
) on the
CD-ROM. Depending on the settings of your computer, the file name may be
“Setup”.
3 When the following message appears, click “OK”.
4 Click the button that corresponds to your type of CD-ROM
drive.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
If you are using an external CD-ROM drive, follow the instructions on
the screen and copy the contents of the CD-ROM to your hard disk.
When the copy is complete, click “Main Menu”.
The Main Menu of the Easy Installation Wizard appears.
5 Click “Install Driver”.
The following screen appears.
Insert the Wireless LAN PC Card and follow the instructions on the
screen to install the device driver.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Insert the Wireless LAN PC Card in the PC card slot.
You do not need to turn off your computer when you insert the
Wireless LAN PC Card.
Insert in arrow
direction
To PC Card slot
Notes
• If your computer has two PC Card slots, insert the Wireless LAN PC Card into the
top slot. If inserted into the bottom slot, the antenna of the Wireless LAN PC Card
will block the top slot. See section “If your computer has two PC Card slots” on
page 28.
• Depending on the depth and configuration of PC card slots on your computer, you
may not be able to insert the Wireless LAN PC Card.
Push the Wireless LAN PC Card into the slot until it is firmly seated. If
the card does not fit easily, do not force it in. Take the card out and try
reinserting it.
When you insert the Wireless LAN PC Card, the device driver installed
automatically. When installation is complete, proceed to step 7.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
7 When installation is complete, the following screen appears.
Click “Continue”.
8 Click “Install Software Utility”.
The utility installation starts.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
9 Follow the instructions on the screen to complete the
installation.
This completes the installation of the software.
Once Wireless Panel is installed,
system taskbar.
appears on your Windows operating
What to do next
Make Access Point connection settings.
When using the Windows Me or Windows 2000 operating system, proceed
to page 20.
When using the Windows XP operating system, proceed to page 24.
z Hint
When using the Windows XP operating system, click “Main Menu” as necessary to return
to the first screen of the wizard, or click
to close the Easy Installation Wizard.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Making Access Point Connection Settings
After installing the necessary software, you must make the necessary
settings to establish a connection with the Access Point.
If you want to establish a connection in Peer to Peer Network connection
mode, refer to the Wireless Panel Help for details about the necessary
settings.
Windows Me or Windows 2000 operating system
1 Click “Connect to Access Point”.
The following screen appears.
2 Make the appropriate settings.
1
2
20
Download from Www.Somanuals.com. All Manuals Search And Download.
1Network Name (SSID)
This is a unique ID used to identify wireless networks. The setting
can be made individually for Access Point Network connection
mode and Peer to Peer Network connection mode. When connecting
to an existing network, consult your network administrator
regarding the proper settings. When changing an existing Network
Name, you can use up to 32 alphanumeric characters (including
symbols).
z Hints
• Opening the “Network Name” drop-down list will show the Network Names
of any Access Points within range. You can then select a Network Name from
the list.
• When using the Wireless LAN Access Point PCWA-A320, the default
Network Name (SSID) of the Access Point is shown on the ID label of the
Access Point. For details on the position of the label and other information,
refer to the manuals provided with the Access Point.
2WEP
If Data Encryption (WEP) is enabled for the Access Point to which
you connect, select this item. When this item is selected, you also
need to enter the encryption key (WEP key) in the “Key” and
“Confirm key” fields.
The data encryption function serves to prevent unauthorized access
to the network. For security reasons, it is strongly recommended
that you enable this feature. The setting can be configured
individually for Access Point Network connection mode and Peer to
Peer Network connection mode. When connecting to an existing
network, consult your network administrator regarding the proper
settings. For information on how to control this setting at the Access
Point, refer to the manuals of the Access Point.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Key
If data encryption (WEP) is enabled for the Access Point, enter the
encryption key (WEP key) here. Because this key functions as a
password that enables communication with the network, the key
entered here must be exactly the same as that set for the Access
Point. Only computers for which the key has been configured
correctly can join the network. The number of characters depends
on the “ASCII/Hex” and “Length” settings (see table below).
ASCII
Hexadecimal
Permissible characters
Alphanumeric characters
5 or 13 characters
0 to 9, A to F, a to f
10 or 26 characters
Maximum number
of characters
Confirm key
Re-enter the encryption key that you entered in the “Key” box.
z Hint
This product supports a function called “roaming” which allows the creation of a
wireless network with multiple Access Points for wider coverage. When using
this function, configure all Access Points to the same Network Name (SSID) and
Data Encryption (WEP) settings.
3 When you are done, click “Next”.
The following screen appears.
4 Make sure that the settings are correct, and then click
“Connect”.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Wait until the Wireless LAN PC Card connects to the Access Point.
When the Wireless LAN PC Card establishes the connection with the
Access Point, the following screen appears.
This completes the Access Point connection settings procedure.
z Hint
You can change the connection settings and network connection mode from
Wireless Panel. For details about how to use Wireless Panel, refer to the Wireless
Panel Help.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows XP operating system
After installing the necessary software, you must make the necessary
settings to establish a connection with the Access Point.
If you want to establish a connection in Peer to Peer Network connection
mode, refer to the Wireless Panel Help for details about the necessary
settings.
Note
Before configuring the Wireless LAN PC Card
Perform the following steps to confirm that the “Use Windows to configure my wireless
network settings” check box is selected. This option is selected by default.
1 Click “Start”, “Control Panel”, and double-click “Network
Connections”.
zHint
If “Network Connections” is not displayed, click “Switch to Classic View”.
2 Right-click “Wireless Network Connection *” (“*” is a
number that differs according to the computer settings),
and click “Properties” on the shortcut menu.
3 Click the “Wireless Network” tab.
4 Confirm that the “Use Windows to configure my wireless
network settings” check box is selected. If not, select it.
1 Click “Start”, point to “Connect To”, and click “Show all
connections”.
The “Network Connections” window appears.
2 Right-click “Wireless Network Connection *” (“*” is a number
that differs according to the computer settings), and click
“View Available Wireless Networks” on the shortcut menu.
The “Connect to Wireless Network” dialog box appears.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
z Hints
•
If the computer is not connected to a wireless network, an “x” is shown for the
“Wireless Network Connection *” icon in the “Network Connections” window.
• If you have installed Windows XP Service Pack 1, see page 26.
3 From the “Available Wireless Networks” list in the “Connect
to Wireless Network” dialog box, select the Access Point to
which you want to connect.
z Hint
The “Available Wireless Networks” list shows the names of Access Points within
communication range of the computer. When using the Wireless LAN Access Point
PCWA-A320, the default Network Name (SSID) of the Access Point is shown on
the ID label of the card. For details on the position of the label and other
information, refer to the manuals of the Access Point. Because the Network Name of
an Access Point may have been changed, consult your network administrator if you
are not sure.
4 If Data Encryption (WEP) is enabled for the Access Point,
enter the encryption key (WEP key) in the “Network key”
field.
The key entered here must be exactly the same as that set for the
Access Point. Permissible characters and their maximum number are
detailed below.
ASCII
Hexadecimal
Permissible characters
Alphanumeric characters
5 or 13 characters
0 to 9, A to F, a to f
10 or 26 characters
Maximum number
of characters
25
Download from Www.Somanuals.com. All Manuals Search And Download.
z Hints
• ASCII and hexadecimal characters are automatically identified.
• The data encryption (WEP) function serves to prevent unauthorized access to the
network. When the function is enabled, only computers configured with the
correct encryption key (WEP key) can join the network. For security reasons, it is
strongly recommended that you enable this feature. The setting can be made
individually for Access Point Network connection mode and Peer to Peer Network
connection mode. When connecting to an existing network, consult your network
administrator regarding the proper settings. For information on how to control this
setting at the Access Point, refer to the manuals of the Access Point.
❑ When using Service Pack 1
If you installed Windows XP Service Pack 1, steps 3 and 4 must be
performed as follows.
3 From the “Available Wireless Networks” list in the
“Connect to Wireless Network” dialog box, select the
Access Point to which you want to connect.
4 Depending on the Data Encryption (WEP) settings of the
Access Point, proceed as follows.
• Data Encryption (WEP) at selected Access Point is
enabled
Enter the encryption key (WEP key) in the “Network key” field.
(The input is shown only as asterisks.) For verification, the same
string must be entered once more in the “Confirm network key”
field.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
• Data Encryption (WEP) at selected Access Point is
disabled
Select the “Allow me to connect to the selected wireless network,
even though it is not secure” check box. (For security reasons,
enabling data encryption is recommended.)
5 Click “Connect”.
Connection to the Access Point is established.
If the Access Point has already been configured, the setup procedure is
now complete.
If you want to change the Access Point settings, refer to the manuals of
the Access Point for information on how to proceed.
Note
To use an Access Point to connect to the Internet, you must change the Access Point
default settings.
z Hint
For additional information on the wireless network capabilities of the Windows XP
operating system, refer to Windows XP “Help and Support”. (Click “Start”, and
click “Help and Support”, enter “wireless” into the Search field, and click the green
arrow icon.) You may also wish to consult the Windows XP operating system
documentation.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing the Wireless LAN PC Card
and Precautions When Inserting it
This section explains how to remove the Wireless LAN PC Card and
outlines precautions when inserting the card in a computer with two card
slots arranged one above the other.
z Hint
You do not need to turn off your computer when you insert or remove the Wireless LAN
PC Card.
To remove the Wireless LAN PC Card
1 Quit any software accessing the wireless LAN (e.g. Internet
Explorer).
2 Click
on your Windows operating system taskbar.
3 Click “Safely remove Sony 802.11g Wireless LAN Adapter”
or “Stop Sony 802.11g Wireless LAN Adapter” on the
shortcut menu that appears.
If your computer has two PC Card slots
Notes
• When using a computer which has two PC Card slots arranged vertically (one above the
other), insert the Wireless LAN PC Card into the top slot. If inserted into the bottom
slot, the antenna of the Wireless LAN PC Card will block the top slot.
• If you insert the Wireless LAN PC Card into a slot other than the one you usually use,
the computer treats the card as a new device and automatically begins installing device
drivers for it. Completing the driver installation makes it possible to use the Wireless
LAN PC Card in that slot. Installation is performed automatically by the installation
wizard. (For instructions on how to uninstall the Wireless LAN PC Card driver, see
page 50.)
z Hint
If you are using the Windows Me or Windows 2000 operating system, you can register up
to 32 networks for each PC card slot. However, you have to register each network
individually. You cannot share the settings across slots.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking the communication status
Checking the wireless signal strength
The communication status is shown by the signal level indicator on your
Windows operating system taskbar.
Signal level indicator
Meaning of indicator appearance
Excellent
Good
Poor
Out of range
Card not inserted
(Wireless LAN PC Card is not inserted or not
recognized correctly)
Peer to Peer
(Communicating in Peer to Peer Network connection
mode)
Checking network information
To obtain information about the network to which you are connected,
proceed as follows.
Double-click the signal level indicator on your Windows operating system
taskbar.
The Wireless Panel main screen appears, and information about the
network connection is shown. For details, refer to the Wireless Panel Help.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Wireless Panel
The Wireless Panel is a software application that shows information about
the communication status of the computer connected to the wireless
network. Normally, the Wireless Panel runs in the background and only
shows the radio signal condition by means of the signal level indicator on
your Windows operating system taskbar. The main screen of the Wireless
Panel contains more detailed information. When running under operating
systems other than Windows XP, communication setup and network
switching are also performed using the Wireless Panel.
Notes
• To use the Wireless Panel under the Windows 2000 operating system to modify
communication settings, log on with a user account listed in “Administrators”. You
cannot modify settings when logged on with any other account.
• On a computer running the Windows XP operating system, communication setup and
network switching are not performed with the Wireless Panel but with built-in
functions of the Windows XP operating system. However, the Wireless Panel can be
used to check the communication status.
Opening the Wireless Panel
To open the Wireless Panel, proceed as follows.
Double-click the signal level indicator on your Windows operating
system taskbar.
The Wireless Panel appears.
z Hints
• For information on the signal level indicator, see “Checking the wireless signal
strength” on page 29.
• When you move the mouse pointer over an item in the Wireless Panel screen, a short
description of that item appears.
• For details about how to use Wireless Panel, refer to the Wireless Panel Help. For
details about how to access Help, see page 10.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Manually installing, verifying, and
removing the supplied software
Installing the Wireless LAN PC Card driver manually
Notes
• To install the supplied software on a computer running the Windows 2000 operating
system, log on with a user account listed in “Administrators”. To install the supplied
software on a computer running the Windows XP operating system, log on with a user
account with administrator access privileges. You cannot install the software or modify
settings when logged on with any other account.
• Exit all other Windows operating system programs.
1 Insert the supplied CD-ROM into the CD-ROM drive of your
computer.
2 In the Easy Installation Wizard dialog box, click “Exit”.
3 If your computer has only one PC card slot and it is currently
used, copy the “Driver” folder from the supplied CD-ROM to
the hard disk of your computer before inserting the Wireless
LAN PC Card.
The following explanation assumes that a folder called “temp” was
created on drive C and that the data was copied to this folder.
4 Insert the Wireless LAN PC Card into the PC Card slot of the
computer.
5 Install the Wireless LAN PC Card driver.
The actual procedure differs slightly, depending on whether you are
using the Windows Me, Windows 2000, or Windows XP operating
system. See the section specific to your operating system.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows Me operating system:
1 Select “Specify the location of the driver” and click “Next”.
2 Select the “Specify a location” check box.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Click “Browse” and specify the location of the driver in the
dialog box that appears.
z Hint
If the “Driver” folder from the CD-ROM has been copied to the “temp” folder on
drive C, enter “C:\temp\Driver\WinMe”.
4 Click “OK”.
5 Click “Next”.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Click “Next”.
The driver is installed.
7 Click “Finish”.
Restart the computer.
Windows 2000 operating system:
1 Click “Next”.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Select “Search for a suitable driver for my device” and click
“Next”.
3 Select the “Specify a location” check box and click “Next”.
4 Click “Browse” and specify the location of the driver in the
dialog box.
z Hint
If the “Driver” folder from the CD-ROM has been copied to the “temp” folder on
drive C, enter “C:\temp\Driver\WinXP2K”.
5 Click “OK”.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Click “Next”.
The driver is installed.
7 Click “Finish”.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows XP operating system:
1 Select “Install from a list or specific location” and click
“Next”.
2 Select the “Include this location in the search” check box
and click “Browse”.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
3 In the dialog box that appears, select the folder that
contains the driver and click “OK”.
z Hint
If the “Driver” folder from the CD-ROM has been copied to the “temp” folder on
drive C, select “C:temp\Driver\WinXP2K”.
4 Click “OK”.
5 Click “Next”.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Click “Finish”.
Installing the Wireless Panel manually
Note
When using the Windows 2000 operating system, log on with a user account listed in
“Administrators”. When using the Windows XP operating system, log on with a user
account with administrator access privileges.
Before installation
• Install the Access Point and connect it to a power outlet when using the
Access Point Network connection mode.
• Complete installation of the Wireless LAN PC Card driver. (See page 31)
• Exit all other Windows operating system programs.
1 Insert the supplied CD-ROM into the CD-ROM drive of your
computer.
2 In the Easy Installation Wizard dialog box, click “Exit”.
3 If your computer has only one PC card slot and it is currently
used, copy the “WPanel” folder from the supplied CD-ROM
to the hard disk of your computer before inserting the
Wireless LAN PC Card.
The following explanation assumes that a folder called “temp” was
created on drive C and that the data was copied to this folder.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Go to the “WPanel” folder copied from the CD-ROM and
double-click “Setup.exe”.
Depending on your computer’s settings, the file name “Setup.exe” may
be displayed as “Setup”. If there are multiple files named “Setup” in
the same folder, double-click the one with the following icon.
5 Click “Next”.
6 The “License Agreement” dialog box appears. Click “Yes” to
accept.
The “Choose Destination Location” dialog box appears.
7 Click “Next”.
The Wireless Panel software is installed.
8 Click “Finish”.
Once Wireless Panel is installed,
system taskbar.
appears on your Windows operating
If you installed Wireless Panel manually, see the following for details about
how to connect to the Access Point.
• With the Windows Me and Windows 2000 operating systems, see
“Connecting to the Access Point with Wireless Panel (Windows Me/2000
operating system)” on page 41.
• With the Windows XP operating system, see “Making Access Point
Connection Settings” on page 20.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to the Access Point with Wireless Panel
(Windows Me/2000 operating system)
1 Double-click
on your Windows operating system taskbar.
The Wireless Panel screen appears.
2 Click the “Network List” tab, select a wireless network from
the list, and click “Register”.
The “Registering Network” dialog box appears.
3 If data encryption (WEP) is enabled for the Access Point,
select the “WEP” check box, enter the encryption key in the
“Key” box, and then confirm it by entering it again in the
“Confirm key” box.
4 Click “Connect”.
The Wireless LAN PC Card connects to the Access Point.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Verifying Wireless LAN PC Card driver installation
To verify that the Wireless LAN PC Card driver has been installed
properly, perform the following steps.
Windows Me operating system:
1 Click “Start”, point to “Settings”, and click “Control Panel”.
Control Panel appears.
2 Double-click the “System” icon.
z Hint
If the “System” icon is not shown, select “View all Control Panel options”.
3 Click the “Device Manager” tab.
4 Click “View devices by type”.
5 Double-click “Network adapters”.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Double-click “Sony 802.11g Wireless LAN Adapter”.
The “Sony 802.11g Wireless LAN Adapter Properties” dialog box
appears.
Note
The Wireless LAN PC Card is not working properly in the following cases:
• “Sony 802.11g Wireless LAN Adapter” is shown with an “X” or “!” symbol.
c Click “Sony 802.11g Wireless LAN Adapter” and click “Remove” to uninstall
the driver. Then repeat the installation process.
• Double-clicking “Network Adapters” does not display “Sony 802.11g Wireless
LAN Adapter”.
c Remove the Wireless LAN PC Card. Then repeat the installation process.
• Double-clicking “Other devices” displays “Ethernet Controller”.
c Click “Ethernet Controller”, then click “Remove” to uninstall the driver. Repeat
the installation process.
7 Confirm that the message “This device is working properly.”
is displayed under “Device status”.
Note
If “This device is working properly.” is not shown, the Wireless LAN PC Card is not
working correctly. Perform steps 1 - 5, click “Sony 802.11g Wireless LAN
Adapter”, then click “Remove” to uninstall the driver. After uninstalling, restart the
computer and repeat the installation process.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
8 Click “OK” to close the “Sony 802.11g Wireless LAN Adapter
Properties” dialog box.
The “System Properties” dialog box appears.
9 Click “OK” to close the “System Properties” dialog box.
Control Panel appears.
10 Click
to close Control Panel.
If the computer you are using incorporates another Ethernet interface
besides the Wireless LAN PC Card, disable the other interface as follows.
1 Click “Start”, point to “Settings”, and click “Control Panel”.
Control Panel appears.
2 Double-click the “System” icon.
z Hint
If the “System” icon is not shown, select “View all Control Panel options”.
3 Click the “Device Manager” tab and double-click “Network
adapters”.
4 Double-click the network adapter to disable.
5 Click the “General” tab, then select the “Disable in this
hardware profile” check box.
6 Click “OK” to close the Properties dialog box for the network
adapter to disable.
The “System Properties” dialog box appears.
7 Click “OK” to close the “System Properties” dialog box.
Control Panel appears.
8 Click
to close Control Panel.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 2000 operating system:
1 Click “Start”, point to “Settings”, and click “Control Panel”.
Control Panel appears.
2 Double-click the “System” icon.
The “System Properties” dialog box appears.
3 Click the “Hardware” tab, then click “Device Manager”.
The “Device Manager” window appears.
4 In the “View” menu, click “Devices by type”.
5 Double-click “Network adapters”.
6 Double-click “Sony 802.11g Wireless LAN Adapter”.
The “Sony 802.11g Wireless LAN Adapter Properties” dialog box
appears.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
The Wireless LAN PC Card is not working properly in the following cases:
• “Sony 802.11g Wireless LAN Adapter” is shown with an “X” or “!” symbol.
c Right-click “Sony 802.11g Wireless LAN Adapter” and click “Remove” to
uninstall the driver. Then repeat the installation process.
• Double-clicking “Network Adapters” does not display “Sony 802.11g Wireless
LAN Adapter”.
c Remove the Wireless LAN PC Card. Then repeat the installation process.
• Double-clicking “Other devices” displays “Ethernet Controller”.
c Right-click “Ethernet Controller”, then click “Remove” to uninstall the driver.
Repeat the installation process.
7 Confirm that the message “This device is working properly.”
is displayed under “Device status”.
Note
If “This device is working properly.” is not shown, the Wireless LAN PC Card is not
working correctly. Perform steps 1 - 5, right-click “Sony 802.11g Wireless LAN
Adapter”, then click “Remove” to uninstall the driver. After uninstalling, restart the
computer and repeat the installation process.
8 Click “OK” to close the “Sony 802.11g Wireless LAN Adapter
Properties” dialog box.
The “Device Manager” window appears.
9 Click
to close the “Device Manager” window.
The “System Properties” dialog box appears.
10 Click “OK” to close the “System Properties” dialog box.
Control Panel appears.
11 Click
to close Control Panel.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
If the computer you are using incorporates another Ethernet interface
besides the Wireless LAN PC Card, disable the other interface as follows.
1 Click “Start”, point to “Settings”, and click “Network and Dial-
up Connections”.
The “Network and Dial-up Connections” window appears.
2 Select the network adapter to disable.
3 On the “File” menu, click “Disable”.
4 Click
window.
to close the “Network and Dial-up Connections”
Windows XP operating system:
1 Click “Start” and click “Control Panel”.
Control Panel appears.
2 Double-click the “System” icon.
The “System Properties” dialog box appears.
z Hint
If the “System” icon is not displayed, click “Switch to Classic View”.
3 Click the “Hardware” tab, then click “Device Manager”.
The “Device Manager” window appears.
4 On the “View” menu, click “Devices by type”.
5 Double-click “Network adapters”.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Double-click “Sony 802.11g Wireless LAN Adapter”.
The “Sony 802.11g Wireless LAN Adapter Properties” dialog box
appears.
Note
The Wireless LAN PC Card is not working properly in the following cases:
• “Sony 802.11g Wireless LAN Adapter” is shown with an “X” or “!” symbol.
c Right-click “Sony 802.11g Wireless LAN Adapter” and click “Remove” to
uninstall the driver. Then repeat the installation process.
• Double-clicking “Network Adapters” does not display “Sony 802.11g Wireless
LAN Adapter”.
c Remove the Wireless LAN PC Card. Then repeat the installation process.
• Double-clicking “Other devices” displays “Ethernet Controller”.
c Right-click “Ethernet Controller”, then click “Remove” to uninstall the driver.
Repeat the installation process.
7 Confirm that the message “This device is working properly.”
is displayed under “Device status”.
Note
If “This device is working properly.” is not shown, the Wireless LAN PC Card is not
working correctly. Perform steps 1 - 5, right-click “Sony 802.11g Wireless LAN
Adapter”, then click “Remove” to uninstall the driver. After uninstalling, restart the
computer and repeat the installation process.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
8 Click “OK” to close the “Sony 802.11g Wireless LAN Adapter
Properties” dialog box.
The “Device Manager” window appears.
9 Click
to close the “Device Manager” window.
The “System Properties” dialog box appears.
10 Click “OK” to close the “System Properties” dialog box.
Control Panel appears.
11 Click
to close Control Panel.
If the computer you are using incorporates another Ethernet interface
besides the Wireless LAN PC Card, disable the other interface as follows.
1 On the “Start” menu, click “Control Panel”, and double-click
“Network Connections”.
The “Network Connections” window appears.
Note
If “Network Connections” is not displayed, click “Switch to Classic View” on the
left of Control Panel.
2 From “LAN or high-speed Internet”, select the network
adapter to disable.
3 On the “File” menu, click “Disable”.
4 Click
to close the “Network Connections” window.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Uninstalling the Wireless LAN PC Card driver
To uninstall the Wireless LAN PC Card driver, proceed as follows.
z Hint
For information on how to install the Wireless LAN PC Card driver, see page 31.
Windows Me operating system:
1 Click “Start”, point to “Settings”, and click “Control Panel”.
Control Panel appears.
2 Double-click the “System” icon.
The “System Properties” dialog box appears.
z Hint
If the “System” icon is not shown, select “View all Control Panel options”.
3 Click the “Device Manager” tab.
4 Click “View devices by type”.
5 Double-click “Network adapters”.
6 Click “Sony 802.11g Wireless LAN Adapter”, then click
“Remove”.
The “Confirm Device Removal” dialog box appears.
7 Click “OK” to uninstall.
The message “To finish removing your hardware, you must restart
your computer. Do you want to restart your computer now?” appears.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
8 Remove the Wireless LAN PC Card from its slot, then click
“Yes”.
The computer restarts. This completes uninstallation of the driver.
Windows 2000 operating system:
Notes
• With the Windows 2000 operating system, only users with administrator access
privileges can uninstall drivers. Log on to the Windows 2000 operating system with a
user account listed in “Administrators”.
• Exit all programs before running the uninstall process.
1 Click “Start”, point to “Settings”, and click “Control Panel”.
Control Panel appears.
2 Double-click the “System” icon.
The “System Properties” dialog box appears.
3 Click the “Hardware” tab, then click “Device Manager”.
The “Device Manager” window appears.
4 On the “View” menu, click “Devices by type”.
5 Double-click “Network adapters”, and double-click “Sony
802.11g Wireless LAN Adapter”.
The “Sony 802.11g Wireless LAN Adapter Properties” dialog box
appears.
6 Click the “Driver” tab, then click “Uninstall”.
The “Confirm Device Removal” dialog box appears.
7 Click “OK”.
The Device Manager window appears.
8 Click
to close the “Device Manager” window.
The “System Properties” dialog box appears.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
9 Click “OK” to close the “System Properties” dialog box.
Control Panel appears.
10 Click
to close Control Panel.
Windows XP operating system:
Notes
• With the Windows XP operating system, only users with administrator access privileges
can uninstall drivers. Log on to the Windows XP operating system with a user account
with administrator access privileges.
• Exit all programs before running the uninstall process.
1 Click “Start” and click “Control Panel”.
Control Panel appears.
2 Double-click the “System” icon.
The “System Properties” dialog box appears.
z Hint
If the “System” icon is not displayed, click “Switch to Classic View”.
3 Click the “Hardware” tab, then click “Device Manager”.
The “Device Manager” window appears.
4 On the “View” menu, click “Devices by type”.
5 Double-click “Network adapters”, and Double-click “Sony
802.11g Wireless LAN Adapter”.
The “Sony 802.11g Wireless LAN Adapter Properties” dialog box
appears.
6 Click the “Driver” tab, then click “Uninstall”.
The “Confirm Device Removal” dialog box appears.
7 Click “OK”.
The Device Manager window appears.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
8 Click
to close the Device Manager window.
The “System Properties” dialog box appears.
9 Click “OK” to close the “System Properties” dialog box.
Control Panel appears.
10 Click
to close Control Panel.
Uninstalling the Wireless Panel
To uninstall the Wireless Panel, proceed as follows.
Note
Exit the Wireless Panel with the icon on your Windows operating system taskbar before
proceeding.
z Hint
For information on how to install the Wireless Panel, see page 39.
Windows Me operating system:
Note
Exit all programs before running the uninstall process.
1 Click “Start”, point to “Settings”, and click “Control Panel”.
Control Panel appears.
2 Double-click the “Add/Remove Programs” icon.
The “Add/Remove Programs Properties” dialog box appears.
3 Select “Wireless Panel” and click “Add/Remove”.
The “Confirm File Deletion” dialog box appears.
4 Click “OK”.
The software uninstall process is carried out.
5 Click “Finish”.
The uninstall process is complete.
Download from Www.Somanuals.com. All Manuals Search And Download.
53
Windows 2000 operating system:
Notes
• With the Windows 2000 operating system, only users with administrator access
privileges can uninstall software. Log on to the Windows 2000 operating system with a
user account listed in “Administrators”.
• Exit all programs before running the uninstall process.
1 Click “Start”, point to “Settings”, and click “Control Panel”.
Control Panel appears.
2 Double-click the “Add/Remove Programs” icon.
The “Add/Remove Programs” dialog box appears.
3 Select “Wireless Panel” and click “Change/Remove”.
The “Confirm File Deletion” dialog box appears.
4 Click “OK”.
The software uninstall process is carried out, and then the InstallShield
completion dialog box appears.
5 Click “Finish”.
The uninstall process is complete.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows XP operating system:
Notes
• With the Windows XP operating system, only users with administrator access privileges
can uninstall software. Log on to the Windows XP operating system with a user account
with administrator access privileges.
• Exit all programs before running the uninstall process.
1 Click “Start” and click “Control Panel”.
Control Panel appears.
2 Double-click the “Add or Remove Programs” icon.
The “Add or Remove Programs” window appears.
z Hint
If the “Add or Remove Programs” icon is not displayed, click “Switch to Classic
View”.
3 Select “Wireless Panel” and click “Change/Remove”.
The “Confirm File Deletion” dialog box appears.
4 Click “OK”.
The software uninstall process is carried out, and then the maintenance
completion dialog box appears.
5 Click “Finish”.
The uninstall process is complete.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning
Precautions
Clean the casing with a soft cloth, lightly
moistened with water or a mild detergent
solution. Do not use any type of abrasive
pad, scouring powder, or solvent such as
alcohol or benzene as it may damage the
finish of the casing.
Safety
Do not drop or cause a mechanical shock
to the Wireless LAN PC Card, as this may
damage the unit.
Installation
Do not expose the Wireless LAN PC Card
to the following conditions:
• Unstable surfaces
• High humidity or poor ventilation
• Excessive dust
• Direct sunlight or extreme heat
• Closed cars
• Magnetized location (near magnets,
speakers, or televisions)
• Locations exposed to frequent vibration
• Locations where the transmission of
radio waves may be obstructed by metal
plates or concrete walls
Operation
If the Wireless LAN PC Card is moved
directly from a cold location to a warm
locations, or if it is placed in a very damp
environment, moisture may condense on
the parts inside. The Wireless LAN PC
Card may not operate properly if moisture
condensation occurs.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Getting help
This section describes how to get help and
support from Sony, as well as
troubleshooting tips for your Wireless
LAN PC Card.
Protocol support
TCP/IP compliant
Standard compliance
IEEE 802.11b
IEEE 802.11g
About Sony’s Support Options
Radio frequency
Sony provides several support options for
your Wireless LAN PC Card.
2.4 GHz wireless network:
2.4 to 2.4835 GHz (ISM band)
❑Operating Instructions explains
how to use your Wireless LAN PC
Card.
Modulation
DS-SS
OFDM
❑Quick Start Guide explains how to
install software required to use the
Wireless LAN PC Card (IEEE 802.11g:
2.4 GHz/54 Mbps) PCWA-C300S. The
document also contains answers to
frequently asked questions and common
problems.
General
Power requirements
3.3 V DC (supplied from the computer
through the PC card adapter)
Current
Peak current at transmission: 700 mA
Peak current at reception: 370 mA
Connector
❑Wireless Panel Online Help is the
Online Help of the supplied Wireless
Panel utility software. Refer to it for
instructions on how to use the software.
PC Card Card Type II (Card Bus)
Dimensions
Approx. 2.2 × 0.2 × 3.6 inches
(Approx. 54 × 5 × 91 mm) (W × H × D)
(Antenna height: 0.55 inches (Approx. 14 mm))
Mass
❑The Sony Wireless LAN products
support Web site
Approx. 1.4 oz. (Approx. 40 g)
Operating temperature
wirelesslansupport provides the
latest information on your Wireless
LAN products.
41°F to 95°F (5°C to 35°C) (not condensed)
Environment temperature
–4°F to 140°F (–20°C to 60°C) (not condensed)
❑The Sony e-mail support service
answers your questions by electronic
mail. Just send your question in an
e-mail message and a customer service
representative will reply. To send a
question to Sony e-mail support, fill out
the e-mail form at
Supplied accessories
See “Unpacking” on page 12.
Design and specifications are subject to change
without notice.
support/pc/email.html
57
Download from Www.Somanuals.com. All Manuals Search And Download.
❑The Sony fax-back service provides
you with answers to commonly asked
questions. You can use this automated
service to request a list of available
topics then select the topics you want to
receive. To contact the Sony fax-back
service, call 1-877-760-7669.
Glossary
Access Point (Infrastructure)
Network mode
A method of building a wireless network
using one or more Access Points. For
details, see “Capabilities” on page 5.
❑The Sony Customer Information
Services Center offers information
about your Wireless LAN products and
other Sony products that work with your
computer. To contact the Sony
Channel
A part of the frequency spectrum to be
used for wireless communication.
Customer Information Services Center,
call 1-877-760-7669.
Open 24 hours/day, 7 days/week.
Only client computers and Access Points
set to the same channel can communicate
with each other.
Client
A computer connected to a LAN (Local
Area Network). Also may be called a
client computer.
DHCP (Dynamic Host
Configuration Protocol)
DHCP lets network administrators centrally
manage and automate assignment of client
computer IP addresses.
DNS (Domain Name System)
A system that translates host names into
IP addresses.
Networks that use the TCP/IP protocol,
such as the Internet, use a set of numbers
like 192.168.0.1 (IP address) to identify a
computer. However, since the IP address
is hard to memorize, DNS was developed
identify a computer for convenience. DNS
servers manage these translations from
host names into IP addresses.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
LAN (Local Area Network)
A network which is accessible only to its
members, unlike the Internet which is
open to an unlimited number of people. A
LAN may be built for different purposes.
For example, you can build an office LAN
that is accessible only to members of the
same department or a home LAN that is
accessible only to family members.
Network Name (SSID)
A wireless LAN group identifier
according to the IEEE 802.11 standard.
SSID stands for “Service Set ID”. The
Network Name can be set individually for
each Access Point and Peer to Peer
Network to connect to. When roaming
among multiple Access Points is used, all
Access Points must be configured for the
same Network Name (SSID) and WEP
encryption key.
TCP/IP (Transmission Control
Protocol/Internet Protocol)
TCP/IP is the network communications
protocol that is used to communicate over
the Internet. TCP is a connection-oriented
protocol for establishing reliable,
sequenced data transfer. TCP ensures that
data reaches its destination.
IP assembles and addresses data packets
for transmission to their network
destinations.
WAN (Wide Area Network)
A network that interconnects remote
LANs through the Internet or telephone
lines.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Read the Troubleshooting section of this guide before calling Sony
Customer Information Services. If you still cannot resolve your issue after
reading this section, call Sony Customer Information Services.
Symptom
Cause/Remedy
The Wireless LAN PC Card may not be properly inserted
into the PC card slot of your computer.
My computer does not
detect the Wireless
LAN PC Card.
c Check that the Wireless LAN PC Card is inserted in the
proper direction, then push it in as far as it will go.
You did not enter a password when your Windows operating
system started.
I cannot see other
computers.
c Make sure that you enter a user name and appropriate
password when you log on to your Windows operating
system.
Windows settings are incorrect.
c Check your Windows operating system network settings.
If there are no other computers on the network to which you
are connected, no other computer is displayed.
The Access Point is not connected.
I cannot access the
Internet.
c Follow the instructions in the Access Point Operating
Instructions to connect it properly.
The Wireless LAN PC Card may not be inserted into your
computer.
c See the instructions on page 17 of this manual to insert it
properly.
Communication between the Access Point and your
computer are not established.
c Check the communication status using the Wireless Panel.
For details on how to check the status, see “Checking the
communication status” (page 29).
The Access Point is not properly configured.
c Configure the Access Point with the connection method of
your choice.
Distance between computer and Access Point is too great.
The maximum allowable distance is about 150 feet in line of
sight, but this will vary depending on usage conditions.
c Check the signal level indicator on your Windows
operating system taskbar. If the level is low, bring the
computer and Access Point closer together.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Cause/Remedy
There is interference with other Access Points.
c Try changing the Access Point channel setting.
Data transfer speed is
slow
The network is handling a large amount of simultaneous
traffic.
c Try again when the network load is lower.
Communication distance is long.
c Reduce the communication distance.
There are obstacles (objects blocking radio transmission)
within the communication range.
c Remove the obstacles or change the installation location.
I cannot remember the
WEP Key.
c When using an Access Point, reset the Access Point to its
defaults. For further information about how to reset the
Access Point, see the Access Point Operating Instructions.
c When using a Wireless LAN PC Card in Peer to Peer
Network connection mode, delete the network settings
registered on each computer connected to the network, then
reconfigure the computer’s wireless network settings.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
❑ The Sony Wireless LAN products support Web site
http://www.sony.com/wirelesslansupport provides the
latest information on your Wireless LAN products.
❑ The Sony e-mail support service answers your questions
by electronic mail. Just send your question in an e-mail message
and a customer service representative will reply. To send a
question to Sony e-mail support, fill out the e-mail form at
❑ The Sony fax-back service provides you with answers to
commonly asked questions. You can use this automated service
to request a list of available topics and then select the topics you
want to receive. To contact the Sony fax-back service, call
1-877-760-7669.
❑ The Sony Customer Information Services Center offers
information about your Wireless LAN products and other Sony
products that work with your computer. To contact the Sony
Customer Information Services Center, call
1-877-760-7669.
Open 24 hours/day, 7 days/week.
Printed on 100% recycled paper using VOC (Volatile
Organic Compound)-free vegetable oil based ink.
Printed in Japan
Download from Www.Somanuals.com. All Manuals Search And Download.
|