2-059-563-13(1)
CD/DVD
Player
Operating Instructions
DVP-NS955V
DVP-LS785V
© 2004 Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
On adjusting volume
Do not turn up the volume while listening to
a section with very low level inputs or no
audio signals. If you do, the speakers may be
damaged when a peak level section is played.
Precautions
On safety
• Should any solid object or liquid fall into
the cabinet, unplug the player and have it
checked by qualified personnel before
operating it any further.
On cleaning
Clean the cabinet, panel, and controls with a
soft cloth slightly moistened with a mild
detergent solution. Do not use any type of
abrasive pad, scouring powder or solvent
such as alcohol or benzine.
On power sources
• The player is not disconnected from the AC
power source (mains) as long as it is
connected to the wall outlet, even if the
player itself has been turned off.
• If you are not going to use the player for a
long time, be sure to disconnect the player
from the wall outlet. To disconnect the AC
power cord (mains lead), grasp the plug
itself; never pull the cord.
On cleaning discs
Do not use a commercially available cleaning
disc. It may cause a malfunction.
IMPORTANT NOTICE
Caution: This player is capable of holding a
still video image or on-screen display image
on your television screen indefinitely. If
you leave the still video image or on-screen
display image displayed on your TV for an
extended period of time you risk permanent
damage to your television screen. Plasma
display panel televisions and projection
televisions are susceptible to this.
On placement
• Place the player in a location with adequate
ventilation to prevent heat build-up in the
player.
• Do not place the player on a soft surface
such as a rug.
• Do not place the player in a location near
heat sources, or in a place subject to direct
sunlight, excessive dust, or mechanical
shock.
If you have any questions or problems
concerning your player, please consult your
nearest Sony dealer.
On operation
• If the player is brought directly from a cold
to a warm location, or is placed in a very
damp room, moisture may condense on the
lenses inside the player. Should this occur,
the player may not operate properly. In this
case, remove the disc and leave the player
turned on for about half an hour until the
moisture evaporates.
• When you move the player, take out any
discs. If you don’t, the disc may be
damaged.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Welcome!. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
About This Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Index to Parts and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Guide to the Control Menu Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Hooking Up the Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Step 6: Quick Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Playing Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Resuming Playback From the Point Where You Stopped the Disc
(Multi-disc Resume) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Using the DVD’s Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Various Play Mode Functions
(Programme Play, Shuffle Play, Repeat Play, A-B Repeat Play) . . . . . . 39
Searching for a Particular Point on a Disc
(Search, Scan, Slow-motion Play, Freeze Frame). . . . . . . . . . . . . . . . . . 44
Changing the Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Surround Mode Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Delay Between the Picture and Sound (AV ALIGNMENT)
(DVP-NS955V only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
®
About DivX Video Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Locking Discs
(CUSTOM PARENTAL CONTROL, PARENTAL CONTROL). . . . . . . . . 73
Controlling Your TV or AV Amplifier (Receiver) With the Supplied
Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Language Code List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
5
Download from Www.Somanuals.com. All Manuals Search And Download.
*1 MP3 (MPEG1 Audio Layer 3) is a standard
format defined by ISO (International
Organization for Standardization)/MPEG which
compresses audio data.
About This Manual
®
*2 DivX is a video file compression technology,
developed by DivXNetworks, Inc.
*3 DivX, DivX Certified, and associated logos are
trademarks of DivXNetworks, Inc. and are used
under license.
Check your model name
The instructions in this manual are for the 2
models: DVP-NS955V and DVP-LS785V.
Check your model name by looking at the
front panel of the player. DVP-NS955V is
the model used for illustration purposes.
Any difference in operation is clearly
indicated in the text, for example, “DVP-
NS955V only.”
• Instructions in this manual describe the
controls on the remote. You can also use the
controls on the player if they have the same
or similar names as those on the remote.
• “DVD” may be used as a general term for
DVD VIDEOs, DVD+RWs/DVD+Rs and
DVD-RWs/DVD-Rs.
• The meaning of the icons used in this
manual is described below:
Icons
Meanings
Functions available for DVD
VIDEOs and DVD+RWs/
DVD+Rs or DVD-RWs/DVD-
Rs in video mode
Functions available for DVD-
RWs in VR (Video Recording)
mode
Functions available for VIDEO
CDs (including Super VCDs or
CD-Rs/CD-RWs in video CD
format or Super VCD format)
Functions available for Super
Audio CDs
Functions available for music
CDs or CD-Rs/CD-RWs in
music CD format
Functions available for DATA
CDs (CD-ROMs/CD-Rs/CD-
1
RWs containing MP3* audio
tracks, JPEG image files and
2
3
DivX* * video files)
Functions available for DATA
DVDs (DVD-Rs/DVD-RWs/
DVD+Rs/DVD+RWs)
2
3
containing DivX* * video
files.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Example of discs that the player
cannot play
This Player Can Play the
Following Discs
The player cannot play the following discs:
• CD-ROMs/CD-Rs/CD-RWs other than
those recorded in the formats listed on the
previous page.
• CD-ROMs recorded in PHOTO CD format.
• Data part of CD-Extras.
Format of discs
DVD VIDEO
• DVD Audios.
• DVD-Rs/DVD-RWs/DVD+Rs/DVD+RWs
that do not contain any DivX video files.
DVD-RW
Super Audio
Also, the player cannot play the following
discs:
• A DVD VIDEO with a different region
code.
• A disc that has a non-standard shape (e.g.,
card, heart).
• A disc with paper or stickers on it.
• A disc that has the adhesive of cellophane
tape or a sticker still left on it.
VIDEO CD
Music CD
“DVD VIDEO” and “DVD-RW” are
trademarks.
Region code
Your player has a region code printed on the
back of the unit and only will play DVD
VIDEOs (playback only) labelled with
identical region codes. This system is used to
protect copyrights.
Note about CDs/DVDs
The player can play CD-ROMs/CD-Rs/CD-
RWs recorded in the following formats:
– music CD format
– video CD format
– MP3 audio tracks, JPEG image files, and
DivX video files of format conforming to
ISO 9660* Level 1/Level 2, or its extended
format, Joliet
ALL
DVD VIDEOs labelled
this player.
will also play on
If you try to play any other DVD VIDEO, the
message “Playback prohibited by area
limitations.” will appear on the TV screen.
Depending on the DVD VIDEO, there may
be no region code indication, even though
playing the DVD VIDEO is prohibited by
area restrictions.
– KODAK Picture CD format
* A logical format of files and folders on CD-
ROMs, defined by ISO (International
Organization for Standardization).
The player can play DVD-ROMs/
DVD+RWs/DVD-RWs/DVD+Rs/DVD-Rs
recorded in the following formats:
– DivX video files of format conforming to
UDF.
DVP–XXXX
X
Region code
00V 00Hz
NO.
00W
0-000-000-00
,continued
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
Notes About the Discs
• Notes about DVD+RWs/DVD+Rs, DVD-RWs/
DVD-Rs or CD-Rs/CD-RWs
Some DVD+RWs/DVD+Rs, DVD-RWs/DVD-
Rs, or CD-Rs/CD-RWs cannot be played on this
player due to the recording quality or physical
condition of the disc, or the characteristics of the
recording device and authoring software.
The disc will not play if it has not been correctly
finalized. For more information, refer to the
operating instructions for the recording device.
Note that some playback functions may not work
with some DVD+RWs/DVD+Rs, even if they
have been correctly finalized. In this case, view
the disc by normal playback. Also some DATA
CDs/DATA DVDs created in Packet Write
format cannot be played.
• To keep the disc clean, handle the disc by its
edge. Do not touch the surface.
• Do not expose the disc to direct sunlight or
heat sources such as hot air ducts, or leave it
in a car parked in direct sunlight as the
temperature may rise considerably inside
the car.
• After playing, store the disc in its case.
• Clean the disc with a cleaning cloth.
Wipe the disc from the centre out.
• Music discs encoded with copyright protection
technologies
This product is designed to playback discs that
conform to the Compact Disc (CD) standard.
Recently, various music discs encoded with
copyright protection technologies are marketed
by some record companies. Please be aware that
among those discs, there are some that do not
conform to the CD standard and may not be
playable by this product.
• Do not use solvents such as benzine,
thinner, commercially available cleaners, or
anti-static spray intended for vinyl LPs.
• If you have printed the disc's label, dry the
label before playing.
Note on playback operations of
DVDs and VIDEO CDs
Some playback operations of DVDs and
VIDEO CDs may be intentionally set by
software producers. Since this player plays
DVDs and VIDEO CDs according to the disc
contents the software producers designed,
some playback features may not be available.
Also, refer to the instructions supplied with
the DVDs or VIDEO CDs.
Copyrights
This product incorporates copyright
protection technology that is protected by
U.S. patents and other intellectual property
rights. Use of this copyright protection
technology must be authorized by
Macrovision, and is intended for home and
other limited viewing uses only unless
otherwise authorized by Macrovision.
Reverse engineering or disassembly is
prohibited.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Index to Parts and Controls
For more information, see the pages indicated in parentheses.
Front panel
DVP-NS955V
DVP-LS785V
Lights up when the player outputs
progressive signals.
Lights up when:
– playing an HD (High Density) layer of
Super Audio CDs.
–no disc is inserted.
M FL OFF (Front panel display off)
Lights up when:
– playing a disc that contains multiple
audio signal channels.
– no disc is inserted.
N VIDEO OFF indicator (DVP-NS955V
O H/Playback Dial (DVP-LS785V
F H(play) button (DVP-NS955V only)
(32)
I ./> (previous/next) buttons
,continued
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Front panel display
When playing back a DVD VIDEO/DVD-RW
Playing status
Disc type
Lights up when you can change the angle (57)
Lights up during
Current title/chapter or playing
time (49)
Current audio signal (53)
Disc type
Playing status
Lights up during A-B Repeat Play (42)
When playing back a Super Audio CD, CD, DATA DVD (DivX video), DATA CD (MP3 audio/
DivX video), or VIDEO CD (without PBC)
Lights up during
Repeat Play (41)
2
Playing status
1
Disc type*
Lights up when playing MP3 audio tracks (62)
*1 When playing the HD layer of Super Audio CDs, the disc type is not displayed.
*2 When playing DivX video files, the current track is not displayed.
z Hint
You can adjust the lighting of the front panel
display by setting “DISPLAY” (DVP-NS955V
only) or “DIMMER” (DVP-LS785V only) in
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear panel
DVP-NS955V
COAXIAL OPTICAL
FRONT
REAR
CENTER
R-AUDIO-L
VIDEO
Y
PB/CB
PR/CR
L
S
VIDEO
OUT
R
LINE OUT
COMPONENT VIDEO OUT
PCM/DTS/MPEG/
DOLBY DIGITAL
WOOFER
5.1CH OUTPUT
DIGITAL OUT
LINE 1(RGB)-TV
LINE 2
DVP-LS785V
COAXIAL OPTICAL
L
FRONT
REAR
CENTER
R-AUDIO-L
VIDEO
Y
PB/CB
PR/CR
S
VIDEO
OUT
R
LINE OUT
COMPONENT VIDEO OUT
PCM/DTS/MPEG/
DOLBY DIGITAL
WOOFER
5.1CH OUTPUT
LINE (RGB)-TV
DIGITAL OUT
G COMPONENT VIDEO OUT (Y, PB/
H LINE 1 (RGB)-TV jack (DVP-
NS955V only)/LINE (RGB)-TV jack
(DVP-LS785V only) (17)
,continued
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote
L
m/M
(45)
(scan/slow) buttons
The H button has a tactile dot.*
The + button has a tactile dot.*
T t (TV/video)/TIME/TEXT button
(49)
W
Y VIDEO ON/OFF button
A-B button (DVP-LS785V) (42)
wk PICTURE NAVI (picture navigation)
e;
(instant advance/step) button
ea
(instant replay/step) button
The number 5 button has a tactile dot.*
E
F
(subtitle) button (57)
* Use the tactile dot as a reference when operating
the player.
I SA-CD MULTI/2CH (Super Audio
CD multi/2 channel) button (37)
J SA-CD/CD (Super Audio CD/CD)
button (37)
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to the Control Menu Display
Use the Control Menu to select a function and to view related information. Press DISPLAY
repeatedly to turn on or change the Control Menu display as follows:
, Control Menu display 1
m
Control Menu display 2 ( Only for DATA CDs without DivX video files)
m
Control Menu display off
Control Menu display
The Control Menu display 1 and 2 will show different items depending on the disc type. For
details about each item, see the pages in parentheses.
Example: Control Menu display 1 when playing a DVD VIDEO.
2
Currently playing chapter number*
1
Currently playing title number*
1
Total number of titles*
Playback status
(N Playback,
X Pause,
2
Total number of chapters*
x Stop, etc.)
Control Menu items
Type of disc
being played*
3
(
)
)
1 2 2 7
DVD VIDEO
(
1 8 3 4
4
Playing time*
Current setting
T
1 : 3 2 : 5 5
Selected item
OFF
OFF
SET
ON
Options
Function name of
selected Control
Menu item
PROGRAM
ENTER
DISPLAY
Quit:
Operation message
*1 Displays the scene number for VIDEO CDs
(PBC is on), track number for VIDEO CDs/
Super Audio CDs/CDs, album number for
DATA DVDs/DATA CDs.
*2 Displays the index number for VIDEO CDs/
Super Audio CDs, MP3 audio track number or
JPEG image file number for DATA CDs. DivX
video file number for DATA DVDs.
*3 Displays Super VCD as “SVCD.”
*4 Displays the date for JPEG files.
To turn off the display
Press DISPLAY.
,continued
13
Download from Www.Somanuals.com. All Manuals Search And Download.
List of Control Menu items
Item
Item Name, Function, Relevant Disc Type
Selects the title, scene, or track to be played.
Selects the chapter or index to be played.
Selects the track to be played.
*
ORIGINAL/PLAY LIST (page 36)
Selects the type of titles (DVD-RW) to be played, the ORIGINAL one, or an edited
PLAY LIST.
TIME/TEXT (page 46)
Checks the elapsed time and the remaining playback time.
Input the time code for picture and music searching.
Displays the DVD/Super Audio CD/CD text, or the DATA DVD/DATA CD track/file
name.
MULTI/2CH (page 37)
Selects the playback area on Super Audio CDs when available.
PROGRAM (page 39)
Selects the title, chapter, or track to play in the order you want.
SHUFFLE (page 40)
Plays the title, chapter, or track in random order.
REPEAT (page 41)
Plays the entire disc (all titles/all tracks/all albums) repeatedly or one title/chapter/track/
album/file repeatedly.
A-B REPEAT (page 42)
Specifies the parts you want to play repeatedly.
SHARPNESS (page 60)
Exaggerates the outline of the image to produce a sharper picture.
AV ALIGNMENT (page 61)
Adjust the delay between the picture and sound. (DVP-NS955V only)
PARENTAL CONTROL (page 73)
Set to prohibit playback on this player.
SETUP (page 80)
Use Quick Setup to choose the desired language of the on-screen display, the aspect
ratio of the TV, the audio output signal, and the size of the speaker you are using.
CUSTOM Setup
In addition to the Quick Setup setting, you can adjust various other settings.
RESET
Returns the settings in “SETUP” to the default setting.
ALBUM (page 62)
Selects the album to be played.
FILE (page 46)
Selects the JPEG image file or DivX video file to be played.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
DATE (page 65)
Displays the date the picture was taken by a digital camera.
*
*
*
*
INTERVAL (page 68)
Specifies the duration for which the slides are displayed on the screen.
EFFECT (page 68)
Selects the effects to be used for changing slides during a slide show.
MODE (MP3, JPEG) (page 67)
Selects the data type; MP3 audio track (AUDIO), JPEG image file (IMAGE) or both
(AUTO) to be played when playing a DATA CD.
* These items are not displayed when playing a DATA CD with DivX video file.
z Hint
The Control Menu icon indicator lights up in green
when you select any item
t
except “OFF.” (“PROGRAM,” “SHUFFLE,”
“REPEAT,” “A-B REPEAT,” “SHARPNESS”
only). The “ORIGINAL/PLAY LIST” indicator
lights up in green when you select “PLAY LIST”
(default setting). The “MULTI/2CH” indicator
lights up in green when you select the multi-channel
playback area on a Super Audio CD. The “AV
ALIGNMENT” indicator lights up in green when
set to more than 0 ms (DVP-NS955V only).
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Hookups
Hooking Up the Player
Follow steps 1 to 6 to hook up and adjust the settings of the player.
Notes
• Plug cords securely to prevent unwanted noise.
• Refer to the instructions supplied with the components to be connected.
• You cannot connect this player to a TV that does not have a video input jack.
• Be sure to disconnect the mains lead of each component before connecting.
Step 1: Unpacking
Check that you have the following items:
• Audio/Video cord (pinplug × 3 y pinplug × 3) (1) (supplied with UK models)
• Remote commander (remote) (1)
• R6 (size AA) batteries (2)
Step 2: Inserting Batteries Into the Remote
You can control the player using the supplied remote. Insert two R6 (size AA) batteries by
matching the 3 and # ends on the batteries to the markings inside the compartment. When
using the remote, point it at the remote sensor on the player.
Notes
• Do not leave the remote in an extremely hot or humid place.
• Do not drop any foreign object into the remote casing, particularly when replacing the batteries.
• Do not expose the remote sensor to direct light from the sun or a lighting apparatus. Doing so may cause a
malfunction.
• If you do not use the remote for an extended period of time, remove the batteries to avoid possible damage
from battery leakage and corrosion.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 3: Connecting the Video Cords
Connect this player to your TV monitor, projector, or AV amplifier (receiver) using a video cord.
Select one of the patterns A through D, according to the input jack on your TV monitor,
projector, or AV amplifier (receiver).
In order to view progressive signal (525p or 625p) pictures with a compatible TV, projector, or
monitor, you must use pattern A.
Example: DVP-NS955V
C
D
S VIDEO cord
(not supplied)
INPUT
Audio/video
cord
(suppliedwith
UK models)
S VIDEO
INPUT
VIDEO
TV, projector, or AV
amplifier (receiver)
L
AUDIO
R
TV, projector, or AV
amplifier (receiver)
(yellow)
to LINE OUT (VIDEO)
to S VIDEO OUT
COAXIAL OPTICAL
FRONT
REAR
CENTER
R-AUDIO-L
VIDEO
PB/CB
PR/CR
L
S
VIDEO
OUT
R
LINE OUT
COMPONENT VIDEO OUT
PCM/DTS/MPEG/
DOLBY DIGITAL
WOOFER
5.1CH OUTPUT
DIGITAL OUT
LINE 1(RGB)-TV
LINE
2
to COMPONENT
VIDEO OUT
CD/DVD player
to LINE 2
(DVP-NS955V
only)
(green)
(blue)
(red)
to LINE
(RGB)-TV
Connectiong
the VCR
Component video
cord (not supplied)
SCART cord
(not supplied)
VCR
COMPONENT
VIDEO IN
Y
(green)
PB/CB
PR/CR
(blue)
(red)
TV, projector, or
AV amplifier
(receiver)
A
B
TV
l : Signal flow
,continued
17
Download from Www.Somanuals.com. All Manuals Search And Download.
connect to your TV using both A and B, a special
control signal transmitted via the SCART cable
may cause the signal to be switched to the SCART
jack.
Note
When connecting to a progressive TV, it is
recommended that you use only pattern A. If you
A If you are connecting to a monitor, projector, or AV amplifier
(receiver) having component video input jacks (Y, PB/CB, PR/C
R)
Connect the component via the COMPONENT VIDEO OUT jacks using a component video
cord (not supplied) or three video cords (not supplied) of the same kind and length. You will
enjoy accurate colour reproduction and high quality images.
If your TV accepts progressive 525p/625p format signals, use this connection and press the
PROGRESSIVE button on the front panel to output progressive signals. For details, see “Using
Green
Blue
Green
Blue
Red
Red
B If you are connecting to a SCART input jack
Connect a SCART cord (not supplied). Be sure to make the connections firmly to avoid hum and
noise. When you connect using the SCART cord, check that the TV conforms to S video or RGB
signals. Refer to the operating instructions supplied with the TV to be connected. Also, when
you set “LINE” to “S VIDEO” or “RGB” under “SCREEN SETUP” in the Setup Display
(page 82), use a SCART cord that conforms to each signal. For DVP-NS955V, be sure to
connect your TV to the LINE 1 (RGB)-TV jack on the player.
With this connection, select “NORMAL (INTERLACE)” (default) by pressing the
PROGRESSIVE button on the front panel.
C If you are connecting to a video input jack
Connect the yellow plug of an audio/video cord (supplied with UK models) to the yellow (video)
jack. You will enjoy standard quality images.
With this connection, select “NORMAL (INTERLACE)” (default) by pressing the
PROGRESSIVE button on the front panel.
Yellow
White (L)
Red (R)
Yellow
White (L)
Red (R)
D If you are connecting to an S VIDEO input jack
Connect an S VIDEO cord (not supplied). You will enjoy high quality images.
With this connection, select “NORMAL (INTERLACE)” (default) by pressing the
PROGRESSIVE button on the front panel.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
When connecting to a wide screen TV
Depending on the disc, the image may not fit your TV screen. To change the aspect ratio, see
Notes
• Do not connect a VCR, etc., between your TV and the player. If you pass the player signals via the VCR,
you may not receive a clear image on the TV screen. If your TV has only one audio/video input jack,
connect the player to this jack.
VCR
CD/DVD player
TV
Connect
directly
• Consumers should note that not all high definition television sets are fully compatible with this product and
may cause artifacts to be displayed in the picture. In case of 525 or 625 progressive scan picture problems,
it is recommended that the user switch the connection to the ‘standard definition’ output. If there are
questions regarding your TV set compatibility with this 525p and 625p DVD player model, please contact
our customer service centre.
• When you connect the player to your TV via the SCART jacks, the TV’s input source is set to the player
automatically when you start playback. In this case, press t (TV/video) on the remote to return the input
to the TV.
signals.
When you play a disc recorded in the NTSC colour system, the player outputs the video signal
or the Setup Display etc. in the NTSC colour system and the picture may not appear on the
PAL colour system televisions. In this case, open the tray and remove the disc.
For DVP-NS955V
• If you are connecting to a VCR, connect your VCR to the LINE 2 jack on the player. The VCR can record
the signal only from your TV.
• If you cannot view the pictures from a VCR through this player which is connected to a TV with RGB
component jacks, set
to t (Audio/Video) on your TV. When you select
(RGB), the TV
cannot receive the signal from the VCR.
• If you want to use your VCR’s SmartLink function, connect the VCR to your TV’s SmartLink jack and
connect the player to the TV with another jack.
• The SmartLink function may not work properly if your VCR is connected to your TV via the SCART jacks
on the player.
Using the PROGRESSIVE button
By using the PROGRESSIVE button on the front panel, you can select the signal format in
which the player outputs video signals (Progressive or Interlace), and the conversion method for
progressive signals. The PROGRESSIVE indicator lights up when the player outputs
progressive signals.
Each time you press PROGRESSIVE, the display changes as follows:
PROGRESSIVE AUTO
m
PROGRESSIVE VIDEO
m
NORMAL (INTERLACE)
,continued
19
Download from Www.Somanuals.com. All Manuals Search And Download.
◆PROGRESSIVE AUTO
Select this setting when:
– your TV accepts progressive signals, and,
– the TV is connected to the COMPONENT VIDEO OUT jacks.
Normally select this under the above condition. This automatically detects the software type, and
selects the appropriate conversion method.
Note that the picture will not be clear or no picture will appear if you select these settings when
either of the above conditions is not met.
◆PROGRESSIVE VIDEO
Select this setting when:
– your TV accepts progressive signals, and,
– the TV is connected to the COMPONENT VIDEO OUT jacks, and
– you want to fix the conversion method to PROGRESSIVE VIDEO for video-based software.
Select this if the image is not clear when you select PROGRESSIVE AUTO.
Note that the picture will not be clear or no picture will appear if you select these settings when
either of the above conditions is not met.
◆NORMAL (INTERLACE)
Select this setting when:
– your TV does not accept progressive signals, or,
– your TV is connected to jacks other than the COMPONENT VIDEO OUT jacks (LINE OUT
(VIDEO) or S VIDEO OUT).
◆About DVD software types and the conversion method
DVD software can be divided into two types: film-based software and video based software.
Video-based software is derived from TV, such as dramas and sit-coms, and displays images at
30 frames/60 fields per second. Film-based software is derived from film and displays images
at 24 frames per second. Some DVD software contains both video and film.
In order for these images to appear natural on your screen when output in progressive format,
the progressive signals need to be converted to match the type of DVD software that you are
watching.
Notes
• When you play video-based software in progressive signal format, sections of some types of images may
appear unnatural due to the conversion process when output through the COMPONENT VIDEO OUT
jacks. Images from the S VIDEO OUT and LINE OUT (VIDEO) jacks are unaffected as they are output in
the normal (interlace) format.
• If you set “LINE” in “SCREEN SETUP” to “RGB,” then the player switches to “NORMAL
(INTERLACE).” This will happen even though you select “PROGRESSIVE AUTO” or “PROGRESSIVE
VIDEO.”
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 4: Connecting the Audio Cords
Refer to the chart below to select the connection that best suits your system. Be sure to also read
the instructions for the components you wish to connect.
Select a connection
Select one of the following connections,
A
through
D
.
Components to be connected
Connection
Your setup (example)
TV
A
B
C
D
• Surround effects:
– TVS DYNAMIC (page 54)
Stereo amplifier (receiver) and 2 speakers
• Surround effects:
or
MD deck/DAT deck
• Surround effects:
1
AV amplifier (receiver) having a Dolby*
Surround (Pro Logic) decoder and 3 to 6
speakers
• Surround effects:
AV amplifier (receiver) with 5.1 ch input jacks
and 4 to 6 speakers
• Surround effects:
– Dolby Digital (5.1 ch) (page 94)
– Super Audio CD Multi channel (page 94)
or
AV amplifier (receiver) with digital input jacks
2
having a Dolby Digital, DTS* , or MPEG audio
decoder and 6 speakers
• Surround effects:
– Dolby Digital (5.1 ch) (page 94)
,continued
21
Download from Www.Somanuals.com. All Manuals Search And Download.
z Hint
If you connect an AV amplifier (receiver) that
conforms to the 96 kHz sampling frequency, use
connection
D
.
*1 Manufactured under license from Dolby
Laboratories. “Dolby,” “Pro Logic,” and the
double-D symbol are trademarks of Dolby
Laboratories.
*2 Manufactured under license from Digital
Theater Systems, Inc. U.S. Pat. No’s.
5,451,942; 5,956,674; 5,974,380; 5,978,762;
6, 226, 616; 6, 487, 535 and other U.S. and
world-wide patents issued and pending. “DTS”
and “DTS Digital Surround” are registered
trademarks of Digital Theater Systems, Inc.
Copyright 1996, 2003 Digital Theater Systems,
Inc. All Rights Reserved.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
A
Connecting to your TV
This connection will use your TV’s speakers for sound. If you use the SCART cord in pattern
to your TV.
CD/DVD player
COAXIAL OPTICAL
FRONT
REAR
CENTER
R-AUDIO-L
VIDEO
Y
PB/CB
PR/CR
L
S
VIDEO
OUT
R
LINE OUT
COMPONENT VIDEO OUT
PCM/DTS/MPEG/
DOLBY DIGITAL
WOOFER
5.1CH OUTPUT
DIGITAL OUT
LINE 1(RGB)-TV
LINE
2
A
R-AUDIO-L
VIDEO
TV
(yellow)*
(white)
(red)
(yellow)*
(white)
(red)
LINE OUT
Audio/video
cord (supplied
with UK
to LINE OUT
L/R (AUDIO)
to audio input
models)
l: Signal flow
* The yellow plug is used for video signals (page
17).
z Hint
When connecting to a monaural TV, use a stereo-
mono conversion cord (not supplied). Connect the
LINE OUT L/R (AUDIO) jacks to the TV’s audio
input jack.
,continued
23
Download from Www.Somanuals.com. All Manuals Search And Download.
B
Connecting to a stereo amplifier (receiver) and 2 speakers/Connecting to
an MD deck or DAT deck
B-1
If the stereo amplifier (receiver) has audio input jacks L and R only, use
. If the amplifier
B-2
(receiver) has a digital input jack, or when connecting to an MD deck or DAT deck, use
.
In this case, you can also connect the player directly to the MD deck or DAT deck without using
your stereo amplifier (receiver).
CD/DVD player
COAXIAL OPTICAL
FRONT
REAR
CENTER
R-AUDIO-L
VIDEO
Y
PB/CB
PR/CR
L
S
VIDEO
OUT
R
LINE OUT
COMPONENT VIDEO OUT
PCM/DTS/MPEG/
DOLBY DIGITAL
WOOFER
5.1CH OUTPUT
DIGITAL OUT
LINE 1(RGB)-TV
LINE
2
Optical digital cord
(not supplied)
Remove jack cap
before connecting
B-2
B-1
COAXIAL OPTICAL
R-AUDIO-L
VIDEO
(red)
or
or
PCM/DTS/MPEG/
DOLBY DIGITAL
(white)
LINE OUT
to LINE OUT L/R (AUDIO)
DIGITAL OUT
to DIGITAL OUT
(COAXIAL or OPTICAL)
Stereo audio cord
(not supplied)
Coaxial digital cord
(not supplied)
(white)
(red)
to coaxial or optical digital input
[Speakers]
to audio input
Stereo amplifier (receiver)
Front (L)
MD deck/DAT deck
Front (R)
l: Signal flow
Note
Super Audio CD audio signals are not output from
the DIGITAL OUT jacks.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
C
Connecting to an AV amplifier (receiver) having a Dolby Surround (Pro
Logic) decoder and 3 to 6 speakers
You can enjoy Dolby Surround effects only when playing Dolby Surround audio or multi-
channel audio (Dolby Digital) discs.
C-1
If your amplifier (receiver) has L and R audio input jacks only, use
. If your amplifier
(receiver) has a digital input jack, use
.
C-2
CD/DVD player
COAXIAL OPTICAL
FRONT
REAR
CENTER
R-AUDIO-L
VIDEO
Y
PB/CB
PR/CR
L
S
VIDEO
OUT
R
LINE OUT
COMPONENT VIDEO OUT
PCM/DTS/MPEG/
DOLBY DIGITAL
WOOFER
5.1CH OUTPUT
DIGITAL OUT
LINE 1(RGB)-TV
LINE
2
Optical digital cord
(not supplied)
Remove jack cap
before connecting
C-2
C-1
COAXIAL OPTICAL
R-AUDIO-L
VIDEO
(red)
or
or
PCM/DTS/MPEG/
DOLBY DIGITAL
(white)
LINE OUT
to LINE OUT L/R (AUDIO)
DIGITAL OUT
to DIGITAL OUT
(COAXIAL or OPTICAL)
Stereo audio cord
(not supplied)
Coaxial digital cord
(not supplied)
(white)
(red)
to coaxial or optical digital input
[Speakers]
to audio input
[Speakers]
Front (L)
Amplifier (receiver) with Dolby
Surround decoder
Front (R)
Rear (L)
Rear (R)
Centre
Subwoofer
Rear (mono)
l: Signal flow
Notes
• When connecting 6 speakers, replace the
monaural rear speaker with a centre speaker, 2
rear speakers and a subwoofer.
• Super Audio CD audio signals are not output from
the DIGITAL OUT jacks.
,continued
25
Download from Www.Somanuals.com. All Manuals Search And Download.
D
Connecting to an AV amplifier (receiver) with 5.1 ch input jacks and/or a
digital input jack and 4 to 6 speakers
D-1
If your AV amplifier (receiver) has 5.1 channel inputs, use
.
If you want to use the Dolby Digital, MPEG audio, or DTS decoder function on your AV
amplifier (receiver), connect to its digital jack using D-2 . With the following connections, you
can enjoy a more realistic audio presence in the comfort of your own home.
CD/DVD player
COAXIAL OPTICAL
FRONT
REAR
CENTER
R-AUDIO-L
VIDEO
Y
PB/CB
PR/CR
L
S
VIDEO
OUT
R
LINE OUT
COMPONENT VIDEO OUT
PCM/DTS/MPEG/
DOLBY DIGITAL
WOOFER
5.1CH OUTPUT
DIGITAL OUT
LINE 1(RGB)-TV
LINE
2
to DIGITAL OUT
(COAXIAL or OPTICAL)
D-2
D-1
COAXIAL OPTICAL
to 5.1CH
OUTPUT
FRONT
REAR
CENTER
L
Optical digital cord
(not supplied)
Remove jack cap
before connecting
R
PCM/DTS/MPEG/
DOLBY DIGITAL
WOOFER
DIGITAL OUT
5.1CH OUTPUT
Stereo audio cord
(not supplied)
or
or
Coaxial digital cord
(not supplied)
Monaural audio cord
(not supplied)
to coaxial or optical
digital input
to audio input
[Speakers]
[Speakers]
AV amplifier (receiver) having
5.1ch inputs or/and a decoder
Front (R)
Front (L)
Subwoofer
Centre
Rear (L)
Rear (R)
l: Signal flow
26
Download from Www.Somanuals.com. All Manuals Search And Download.
: Connecting to the 5.1 ch input jacks
D-1
You can enjoy 5.1 ch surround sound using
the internal Dolby Digital, MPEG audio,
DTS, or Super Audio CD Multi decoder of
this player. Note that 7.1-channel MPEG
signals are mixed down to 5.1-channel
signals.
D-2 : Connecting to a digital input jack
This connection will allow you to use the
Dolby Digital, MPEG audio, or DTS decoder
function of your AV amplifier (receiver). You
are not able to enjoy the surround sound
effects of this player.
z Hints
• For connection D-2
For correct speaker location, refer to the operating
instructions of the connected components.
• To enhance the sound performance:
– Use high-performance speakers.
– Use front, rear, and centre speakers of the same
size and performance.
– Place the subwoofer between the left and right
front speakers.
Notes
For connection D-2
• After you have completed the connection, be sure
to set “DOLBY DIGITAL” to “DOLBY
DIGITAL” and “DTS” to “DTS” in Quick Setup
(page 28). If your AV amplifier (receiver) has an
MPEG audio decoder function, set “MPEG” in
“AUDIO SETUP” to “MPEG”.
• When you connect an amplifier (receiver) that
conforms to the 96 kHz sampling frequency, set
“48kHz/96kHz PCM” in “AUDIO SETUP” to
• Super Audio CD audio signals are not output from
the DIGITAL OUT jack.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 5: Connecting the Mains Lead
Plug the player and TV mains lead (power cord) into a mains.
Step 6: Quick Setup
Follow the steps below to make the minimum number of basic adjustments for using the player.
To skip an adjustment, press >. To return to the previous adjustment, press ..
"/1
./>
ENTER
X/x
1
2
3
Turn on the TV.
LANGUAGE SETUP
OSD:
MENU:
AUDIO:
SUBTITLE:
ENGLISH
ENGLISH
FRANÇAIS
DEUTSCH
ITALIANO
Press [/1.
Switch the input selector on your
TV so that the signal from the
player appears on the TV screen.
ESPAÑOL
NEDERLANDS
DANSK
SVENSKA
“Press [ENTER] to run QUICK SETUP”
appears at the bottom of the screen. If this
message does not appear, select
“QUICK” under “SETUP” in the Control
5
Press X/x to select a language.
The player displays the menu and
subtitles in the selected language.
4
Press ENTER without inserting a
disc.
The Setup Display for selecting the
language used in the on-screen display
appears.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Press ENTER.
10Press ENTER.
The Setup Display for selecting the
aspect ratio of the TV to be connected
appears.
The Setup Display for selecting the type
of jack used to connect your amplifier
(receiver) appears.
SCREEN SETUP
TV TYPE:
SCREEN SAVER:
BACKGROUND:
LINE:
Is this player connected to an amplifier
(receiver)? Select the type of jack you
are using.
16:9
16:9
4:3 LETTER BOX
4:3 PAN SCAN
FULL
YES
4:3 OUTPUT:
LINE OUTPUT L/R(AUDIO)
DIGITAL OUTPUT
DIGITAL & 5.1CH OUTPUT
NO
11Press X/x to select the type of
jack (if any) you are using to
connect to an amplifier (receiver),
then press ENTER.
7
8
Press X/xto select the setting that
matches your TV type.
◆ If you have a wide-screen TV or a 4:3
standard TV with a wide-screen mode
Choose the item that matches the audio
◆ If you have a 4:3 standard TV
• 4:3 LETTER BOX or 4:3 PAN SCAN
26 (
A
through
D
).
A
• If you connect just a TV and nothing
else, select “NO.” Quick Setup is
finished and connections are complete.
Press ENTER.
The Setup Display for selecting the type
of video signal output from the LINE
(RGB)-TV jack appears.
B-1
C-1
• Select “LINE OUTPUT L/R
(AUDIO).” Quick Setup is finished and
connections are complete.
SCREEN SETUP
TV TYPE:
16:9
ON
SCREEN SAVER:
BACKGROUND:
LINE:
JACKET PICTURE
VIDEO
B-2
C-2
D-2
4:3 OUTPUT:
VIDEO
S VIDEO
RGB
• Select “DIGITAL OUTPUT.” The
Setup Display for “DOLBY DIGITAL”
appears.
or both
and
D-2
D-1
D-1
9
Press X/x to select the type of
signal you want to output from the
LINE (RGB)-TV jack.
• Select “DIGITAL & 5.1CH OUTPUT.”
The Setup Display for “DOLBY
DIGITAL” appears.
◆ Video signals
◆ S video signals
◆ RGB signals
When you select “RGB,” you will be
unable to use the PROGRESSIVE
button, and the player will not output
video signals from the COMPONENT
VIDEO OUT jacks.
,continued
29
Download from Www.Somanuals.com. All Manuals Search And Download.
12Press X/x to select the type of
Dolby Digital signal you wish to
send to your amplifier (receiver).
15Press ENTER.
◆ When “ DIGITAL OUTPUT” is selected
in step 11
• Quick Setup is finished and
connections are complete.
• If your AV amplifier (receiver) has an
MPEG audio decoder, set “MPEG” to
Choose the signal that matches the audio
26 (
B
through
D
).
AUDIO SETUP
AUDIO ATT:
AUDIO DRC:
AUDIO FILTER:
DOWNMIX:
DIGITAL OUT:
DOLBY DIGITAL:
MPEG:
OFF
STANDARD
SHARP
◆ When “ DIGITAL & 5.1CH OUTPUT” is
selected in step 11
• The Setup Display for “SPEAKER
SETUP” appears.
DOLBY SURROUND
ON
D-PCM
D-PCM
DTS:
48kHz/96kHz PCM:
DOLBY DIGITAL
48kHz/16bit
16Press X/x to select the size of the
centre speaker.
B-2
C-2
If no centre speaker is connected, select
SPEAKER SETUP(DVD)
SIZE:
DISTANCE:
D-2
• DOLBY DIGITAL (only if the
amplifier (receiver) has a Dolby Digital
LEVEL(FRONT):
LEVEL(REAR):
TEST TONE:
FRONT:
OFF
LARGE
SMALL
CENTER:
REAR:
SUBWOOFER:
13Press ENTER.
NONE
YES
“DTS” is selected.
17Press ENTER.
AUDIO SETUP
AUDIO ATT:
AUDIO DRC:
AUDIO FILTER:
DOWNMIX:
DIGITAL OUT:
DOLBY DIGITAL:
MPEG:
OFF
STANDARD
SHARP
“REAR” is selected.
SPEAKER SETUP(DVD)
SIZE:
DISTANCE:
DOLBY SURROUND
ON
D-PCM
DTS
LEVEL(FRONT):
DTS:
48kHz/96kHz PCM:
D-PCM
LEVEL(REAR)
TEST TONE:
FRONT:
:
OFF
48kHz/16bit
LARGE
LARGE(
R
E
A
R)
CENTER:
REAR:
LARGE(SIDE)
14Press X/x to select whether or
not you wish to send a DTS signal
to your amplifier (receiver).
SUBWOOFER:
YES
18Press X/x to select the size of the
rear speakers.
Choose the item that matches the audio
If no rear speaker is connected, select
“NONE.”
26 (
B
through
D
).
B-2
C-2
D-2
• DTS (only if the amplifier (receiver)
30
Download from Www.Somanuals.com. All Manuals Search And Download.
19Press ENTER.
Enjoying the surround sound
effects
“SUBWOOFER” is selected.
SPEAKER SETUP(DVD)
SIZE:
DISTANCE:
LEVEL(FRONT):
LEVEL(REAR):
TEST TONE:
FRONT:
To enjoy the surround sound effects of this
player or your amplifier (receiver), set the
following items as described below for the
OFF
LARGE
CENTER:
REAR:
SUBWOOFER:
YES
26 (
B
through
D
). Each of these is the
NONE
default setting and does not need to be
adjusted when you first connect the player.
YES
20Press X/x to select whether or
not you have connected a
subwoofer.
A
• No additional settings are needed.
21Press ENTER.
C-1
B-1
Quick Setup is finished. All connections
and setup operations are complete.
If your AV amplifier (receiver) has an
MPEG audio decoder, set “MPEG” to
• Set “DOWNMIX” to “DOLBY
B-2
C-2
D-2
• Set “DOWNMIX” to “DOLBY
D-1
• Set “DISTANCE,” “LEVEL (FRONT),”
and “LEVEL (REAR)” according to the
z Hints
• For connections
B-2
C-2
D-2
Set “48kHz/96kHz PCM” to “96kHz/24bit,” only
if you connect an amplifier (receiver) that
conforms to the 96 kHz sampling frequency
• For connections
C-1
D-1
B-1
If the sound distorts even when the volume is
turned down, set “AUDIO ATT” to “ON”
• For DVP-NS955V
The speaker size you set in steps 16 through 20
will also adjust the Super Audio CD speaker size
of “SPEAKER SETUP.” If you want to change
the speaker size for Super Audio CDs, you can set
31
Download from Www.Somanuals.com. All Manuals Search And Download.
3
4
Switch the input selector on your
TV so that the signal from the
player appears on the TV screen.
Playing Discs
◆ When using an amplifier (receiver)
Turn on the amplifier (receiver) and
select the appropriate channel so that you
can hear sound from the player.
Playing Discs
Press Aon the player, and place a
Depending on the DVD or VIDEO CD, some
operations may be different or restricted.
Refer to the operating instructions supplied
with your disc.
disc on the disc tray.
DVP-NS955V
A
H
[/1
Playback side facing down
5
Press H.
H/
Playback
Dial
DVP-LS785V
The disc tray closes. The player starts
playback (continuous play). Adjust the
volume on the TV or the amplifier
(receiver).
A
[/1
Depending on the disc, a menu may
appear on the TV screen. For DVD
Z
[/1
To enjoy the clarity of Super Audio CD/CD
sound more (DVP-NS955V only)
You can minimize the effect of the video
output by switching it off.
Press VIDEO ON/OFF, so that the VIDEO
OFF indicator lights up on the player.
To cancel the setting, press VIDEO ON/OFF
again.
VIDEO
ON/OFF
(DVP-
NS955V
only)
H
To turn off the player
Press [/1. The player enters standby mode.
z Hint
The player turns off automatically whenever you
leave it in stop mode for more than 30 minutes.
(Auto Power Off function)
1
2
Turn on your TV.
Note
Press [/1.
Super Audio CD audio signals are not output from
the DIGITAL OUT jacks.
The player turns on.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
*2 DVD VIDEOs/DVD-RWs/DVD-Rs/
DVD+RWs only. The button cannot be used for
DivX video files.
Additional operations
*3 Video and JPEG pictures only (except
BACKGROUND pictures). You can move the
enlarged picture using C/X/x/c. Depending
upon the contents of the disc, the zoom function
may be cancelled automatically when the picture
is moved.
*4 DATA CDs/DATA DVDs only.
*5 For more details about the H/Playback Dial,
see page 45.
Z
CLEAR
ALBUM +/–
ZOOM
./>
z Hints
(instant replay)
• The Instant Replay function is useful when you
want to review a scene or dialogue that you
missed.
• The Instant Advance function is useful when you
want to pass over a scene that you don’t want to
watch.
X
(instant advance)
x
H
Note
To
Operation
You may not be able to use the Instant Replay or
Instant Advance function with some scenes.
Stop
Pause
Press x
Press X
Locking the disc tray (Child
Lock)
Resume play after
pause
Press X or H
Go to the next chapter, Press > on the
track, or scene in remote, or briefly turn
continuous play mode the H/Playback
You can lock the disc tray to prevent children
from opening it.
5
Dial* (DVP-LS785V
only) on the player
clockwise
[/1
Go back to the
Press . on the
previous chapter,
track, or scene in
continuous play mode Dial* (DVP-LS785V
only) on the player
remote, or briefly turn
the H/Playback
5
counterclockwise
Stop play and remove Press Z
the disc
Replay the previous
scene*
Press
1
(instant replay) during
playback
ENTER
O
RETURN
Briefly fast forward
the current scene*
Press
(instant advance)
during playback
2
When the player is in standby mode, press
O RETURN, ENTER, and then [/1 on the
remote.
The player turns on and “LOCKED” appears
on the front panel display. The A and Z
buttons on the player or the remote do not
work while the Child Lock is set.
3
Magnify the image*
Press ZOOM
repeatedly. Press
CLEAR to cancel.
Go to the next or
previous album.*
Press ALBUM + or –
during playback
4
*1 DVD VIDEOs/DVD-RWs/DVD-Rs only. The
button cannot be used for DivX video files.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
To unlock the disc tray
When the player is in standby mode, press
O RETURN, ENTER, and then [/1 again.
ResumingPlaybackFrom
the Point Where You
Stopped the Disc (Multi-disc
Resume)
Note
Even if you select “RESET” under “SETUP” in the
locked.
The player stores the point where you stopped
the disc for up to 40 discs and resumes
playback the next time you insert the same
disc. If you store a resume playback point for
the 41st disc, the resume playback point for
the first disc is deleted.
H
x
1
2
While playing a disc, press x to
stop playback.
“RESUME” appears on the front panel
display.
Press H.
The player starts playback from the point
where you stopped the disc in step 1.
z Hint
To play from the beginning of the disc, press x
twice, then press H.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
Using the DVD’s Menu
• “MULTI-DISC RESUME” in “CUSTOM
SETUP” must be set to “ON” (default) for this
• The point where you stopped playing is cleared
when:
– you change the play mode.
– you change the settings on the Setup Display.
• For DVD-RWs in VR mode, CDs, Super Audio
CDs, DATA CDs, and DATA DVDs, the player
remembers the resume playback point for the
current disc.
A DVD is divided into long sections of a
picture or a music feature called “titles.”
When you play a DVD which contains
several titles, you can select the title you want
using the TOP MENU button.
When you play DVDs that allow you to select
items such as language for the sound and
subtitles, select these items using the MENU
button.
The resume point is cleared when:
– you opened the disc tray.
– you disconnect the mains lead.
– the player enters standby mode (DATA CD/
DATA DVD only).
• Resume Play does not work during Shuffle Play
and Programme Play.
Number
buttons
• This function may not work with some discs.
• If “MULTI-DISC RESUME” in “CUSTOM
SETUP” is set to “ON” and you playback a
recorded disc such as DVD-RW, the player may
playback other recorded discs from the same
resume point. To play from the beginning, press
x twice and then press H.
ENTER
C/X/x/c
TOP MENU
MENU
1
2
Press TOP MENU or MENU.
The disc’s menu appears on the TV
screen.
The contents of the menu vary from disc
to disc.
Press C/X/x/c or the number
buttons to select the item you want
to play or change.
If you press the number buttons, the
following display appears.
Press the number buttons to select the
item you want.
1
3
Press ENTER.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
3
4
Press X/x to select a setting.
Selecting “ ORIGINAL” or
“PLAY LIST” on a DVD-
RW
Some DVD-RWs in VR (Video Recording)
mode have two types of titles for playback:
originally recorded titles (ORIGINAL) and
titles that can be created on recordable DVD
players for editing (PLAY LIST). You can
select the type of title to be played.
• PLAY LIST: plays the titles created
from “ORIGINAL” for editing.
• ORIGINAL: plays the titles originally
recorded.
Press ENTER.
ENTER
X/x
DISPLAY
1
2
Press DISPLAY when the player is
in stop mode.
The Control Menu appears.
Press X/x to select
(ORIGINAL/PLAYLIST), thenpress
ENTER.
The options for “ORIGINAL/PLAY
LIST” appear.
(
)
)
1 2 2 7
(
1 8 3 4
DVD-RW
T
1 : 3 2 : 5 5
PLAY LIST
PLAY LIST
ORIGINAL
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting a playback layer when
playing a hybrid Super Audio CD
Selecting a Playback
Area for a Super Audio
CD
Some Super Audio CDs consist of an HD
layer and a CD layer. You can select the
playback layer you want to listen to.
Press SA-CD/CD when the player is in stop
mode.
Each time you press the button, an HD layer
or a CD layer is alternately selected. When
playing a CD layer, the “CD” indicator in the
front panel display lights up.
SA-CD
MULTI/2CH
SA-CD/CD
Notes
94.
• Each play mode function works only within the
selected layer or playback area.
Selecting a playback area on a 2
channel + Multi-channel Super
Audio CD
Some Super Audio CDs consist of a 2 channel
playback area and a multi-channel playback
area. You can select the playback area you
want to listen to.
1 Press SA-CD MULTI/2CH in stop
mode.
The following display appears.
2CH
2 Press SA-CD MULTI/2CH repeatedly to
select the item.
• MULTI: plays a multi-channel
playback area.
• 2CH: plays a 2 channel playback area.
The “MULTI” indicator in the front
panel display lights up when playing a
multi-channel playback area.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
z Hint
To play without using PBC, press ./> or the
number buttons while the player is stopped to select
a track, then press H or ENTER.
“Play without PBC” appears on the TV screen and
the player starts continuous play. You cannot play
still pictures such as a menu.
Playing VIDEO CDs With
PBCFunctions(PBCPlayback)
To return to PBC playback, press x twice then
press H.
PBC (Playback Control) allows you to play
VIDEO CDs interactively by following the
menu on the TV screen.
Note
Depending on the VIDEO CD, “Press ENTER” in
step 3 may appear as “Press SELECT” in the
instructions supplied with the disc. In this case,
press H.
Number
buttons
./>
H
x
ENTER
O RETURN
1
2
Start playing a VIDEO CD with PBC
functions.
The menu for your selection appears.
Press the number buttons to select
the item number you want.
3
4
Press ENTER.
Follow the instructions in the
menu for interactive operations.
Refer to the instructions supplied with the
disc, as the operating procedure may
differ depending on the VIDEO CD.
To return to the menu
Press O RETURN.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
(
)
)
1 2 2 7
DVD VIDEO
(
1 8 3 4
Various Play Mode
Functions (Programme Play,
Shuffle Play, Repeat Play, A-BRepeat
Play)
T
1 : 3 2 : 5 5
OFF
OFF
SET
ON
You can set the following play modes:
3 Press X/x to select “ SET t,” then
press ENTER.
“TRACK” is displayed when you play
a VIDEO CD, Super Audio CD, or CD.
PROGRAM
T
Note
ALL CLEAR
– –
1. TITLE
2. TITLE
3. TITLE
4. TITLE
5. TITLE
6. TITLE
7. TITLE
The play mode is cancelled when:
– you open the disc tray.
– the player enters standby mode by pressing [/1.
– –
– –
– –
– –
– –
– –
01
02
03
04
05
Creating your own programme
(Programme Play)
Titles or tracks
recorded on a disc
4 Press c.
You can play the contents of a disc in the
order you want by arranging the order of the
titles, chapters, or tracks on the disc to create
your own programme. You can programme
up to 99 titles, chapters, and tracks.
The cursor moves to the title or track row
“T” (in this case, “01”).
PROGRAM
T
C
ALL CLEAR
1. TITLE
– –
– –
01
02
03
04
05
ALL
– –
– –
– –
– –
– –
– –
2. TITLE
3. TITLE
4. TITLE
5. TITLE
6. TITLE
7. TITLE
01
02
03
04
05
06
CLEAR
Chapters recorded on a disc
5 Select the title, chapter, or track you
want to programme.
H
ENTER
◆ When playing a DVD VIDEO
For example, select chapter “03” of title
“02.”
Press X/x to select “02” under “T,” then
press ENTER.
X/x/c
DISPLAY
1 Press DISPLAY.
PROGRAM
T
C
The Control Menu appears.
ALL CLEAR
– –
– –
ALL
1. TITLE
2. TITLE
3. TITLE
4. TITLE
5. TITLE
6. TITLE
7. TITLE
– –
– –
– –
– –
– –
– –
01
02
03
04
05
06
01
02
03
04
05
2 Press X/x to select
(PROGRAM), then press ENTER.
The options for “PROGRAM” appear.
,continued
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Next, press X/x to select “03” under “C,”
2
3
Select the programme number of the title,
chapter, or track you want to change or
cancel using X/x and press c. If you
want to delete the title, chapter, or track
from the prgramme, press CLEAR.
then press ENTER.
PROGRAM
T
ALL CLEAR
1. TITLE 0 2 0 3
–
– –
– –
– –
– –
– –
– –
– –
2. TITLE
3. TITLE
4. TITLE
5. TITLE
6. TITLE
7. TITLE
01
02
03
04
05
Follow step 5 for new programming. To
cancel a programme, select “--” under
“T,” then press ENTER.
To cancel all of the titles, chapters, or
tracks in the programmed order
Selected title and chapter
1
Follow steps 1 to 3 of “Creating your own
◆ When playing a VIDEO CD, Super
Audio CD, or CD
2
3
Press X and select “ALL CLEAR.”
For example, select track “02.”
Press X/x to select “02” under “T,” then
press ENTER. The track number may be
displayed in 3 digits for a Super Audio
CD.
Press ENTER.
z Hint
You can perform Repeat Play or Shuffle Play of
programmed titles, chapters, or tracks. During
Programme Play, follow the steps of Repeat Play
Selected track
0:15:30
T
PROGRAM
ALL CLEAR
1. TRACK
2. TRACK
3. TRACK
4. TRACK
5. TRACK
6. TRACK
7. TRACK
– –
0 2
– –
– –
– –
– –
– –
– –
Notes
01
02
03
04
05
• When you programme tracks on a Super VCD, the
total playing time is not displayed.
• You cannot use this function with VIDEO CDs
and Super VCDs with PBC playback.
Total time of the programmed tracks
Playing in random order (Shuffle
Play)
6 To programme other titles, chapters,
or tracks, repeat steps 4 to 5.
You can have the player “shuffle” titles,
chapters, or tracks. Subsequent “shuffling”
may produce a different playing order.
The programmed titles, chapters, and
tracks are displayed in the selected order.
7 Press H to start Programme Play.
Programme Play begins.
When the programme ends, you can
restart the same programme again by
pressing H.
CLEAR
SHUFFLE
To return to normal play
Press CLEAR, or select “OFF” after step 2.
To play the same programme again, select
“ON” in step 3 and press ENTER.
H
To change or cancel a programme
1
Follow steps 1 to 3 of “Creating your own
1 Press SHUFFLE during playback.
The following display appears.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing repeatedly (Repeat Play)
TITLE
You can play all of the titles or tracks on a
disc, or a single title, chapter, or track
repeatedly.
You can use a combination of Shuffle or
Programme Play modes.
2 Press SHUFFLE repeatedly to select
the item to be shuffled.
◆ When playing a DVD VIDEO
• TITLE
• CHAPTER
◆ When playing a VIDEO CD,Super
Audio CD, or CD
• TRACK
CLEAR
◆ When Programme Play is activated
• ON: shuffles titles, chapters, or tracks
selected in Programme Play.
REPEAT
To return to normal play
Press CLEAR, or select “OFF” in step 2.
H
z Hints
• You can set Shuffle Play while the player is
stopped. After selecting the “SHUFFLE” option,
press H. Shuffle Play starts.
• Up to 200 chapters in a disc can be played in
random order when “CHAPTER” is selected.
1 Press REPEAT during playback.
The following display appears.
Note
DISC
You cannot use this function with VIDEO CDs and
Super VCDs with PBC playback.
2 Press REPEAT repeatedly to select the
item to be repeated.
◆ When playing a DVD VIDEO
• DISC: repeats all of the titles.
• TITLE: repeats the current title on a
disc.
• CHAPTER: repeats the current chapter.
◆ When playing a DVD-RW
• DISC: repeats all the titles of the
selected type.
• TITLE: repeats the current title on a
disc.
• CHAPTER: repeats the current chapter.
,continued
41
Download from Www.Somanuals.com. All Manuals Search And Download.
◆ When playing a VIDEO CD, Super
Audio CD, or CD
• DISC: repeats all of the tracks.
• TRACK: repeats the current track.
Repeating a specific portion (A-
B Repeat Play)
◆ When playing a DATA CD/DATA DVD
• DISC: repeats all of the albums.
• ALBUM: repeats the current album.
• TRACK (MP3 audio tracks only):
repeats the current track.
You can play a specific portion of a title,
chapter or track repeatedly. (This function is
useful when you want to memorize lyrics,
etc.)
• FILE (DivX video files only): repeats
the current file.
◆ WhenProgramme Play or ShufflePlay
is activated
• ON: repeats Programme Play or Shuffle
Play.
CLEAR
To return to normal play
Press CLEAR, or select “OFF” in step 2.
ENTER
z Hint
You can set Repeat Play while the player is stopped.
After selecting the “REPEAT” option, press H.
Repeat Play starts.
X/x
DISPLAY
Notes
1 Press DISPLAY during playback.
• You cannot use this function with VIDEO CDs
and Super VCDs with PBC playback.
The Control Menu appears.
• When repeating a DATA CD which contains MP3
audio tracks and JPEG image files, and their
playing times are not the same, the sound will not
match the image.
2 Press X/x to select
(A-B
REPEAT), then press ENTER.
The options for “A-B REPEAT” appear.
• When “MODE (MP3, JPEG)” is set to “IMAGE
(
)
)
1 2 2 7
DVD VIDEO
(
1 8 3 4
T
1 : 3 2 : 5 5
OFF
SET
OFF
3 Press X/x to select “ SET t,” then
press ENTER.
The “A-B REPEAT” setting bar appears.
A 18 - 1:32:30
B
42
Download from Www.Somanuals.com. All Manuals Search And Download.
4 During playback, when you find the
starting point (point A) of the portion to
be played repeatedly, press ENTER.
The starting point (point A) is set.
A 18 - 1:32:30 B 18 - 1:33:05
5 When you reach the ending point
(point B), press ENTER again.
The set points are displayed and the
player starts repeating this specific
portion.
To return to normal play
Press CLEAR, or select “OFF” in step 3.
z Hint
For DVP-LS785V, you can also use the A-B
button on the remote.
Notes
• When you set A-B Repeat Play, the settings for
Shuffle Play, Repeat Play, and Programme Play
are cancelled.
• A-B Repeat Play does not work across multiple
titles.
• You cannot set A-B Repeat Play for contents on a
DVD-RW (VR mode) that contains still pictures.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Locating a point quickly using
the previous/next buttons
Searching for a Scene
Searching for a
Particular Point on a
Disc (Search, Scan, Slow-motion
Play, Freeze Frame)
You can search for the next or previous
chapter, track, or scene using ./> on
the player.
During playback, press > or . once
briefly to go to the next or previous chapter/
track/scene. Or, press and hold > or .
to search forward or backwards, and release
the button when you find the point you want
to return to normal playback. (Search)
You can quickly locate a particular point on a
disc by monitoring the picture or playing back
slowly.
Locating a point quickly by
playing a disc in fast forward or
fast reverse (Scan)
m/
M
H
Press
m or M
while playing a
disc. When you find the point you want, press
H to return to normal speed. Each time you
press
m or M
during scan, the
scan speed changes. With each press the
indication changes as shown below. Actual
speeds may differ between discs.
DVP-NS955V
Playback direction
./>
H
×2B t 1M t 2M t 3M
3M (DVD VIDEO/DVD-RW/VIDEO CD/DATA
CD (DivX video)/DATA DVD only)
×2B (DVD VIDEO/Super Audio CD/CD only)
DVP-LS785V
Opposite direction
×2b t 1m t 2m t 3m
H/Playback Dial
3m(DVD VIDEO/DVD-RW/VIDEO CD/DATA
CD (DivX video)/DATA DVD only)
×2b (DVD VIDEO only)
Notes
The “×2B”/ “×2b” playback speed is about
twice the normal speed.
The “3M”/“3m” playback speed is faster
than “2M”/“2m” and the “2M”/“2m”
playback speed is faster than “1M”/
“1m.”
• Depending on the disc, you may not be able to do
some of the operations described.
• For DATA CDs, you can search for a particular
point only on an MP3 audio track.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Watching frame by frame
(Slow-motion Play)
Using the Playback Dial on the
player (DVP-LS785V only)
Press
m or M
when the player is
in pause mode. To return to normal speed,
press H.
You can search for a particular point on a disc
in various ways using the Playback Dial.
Each time you press
m or M
during Slow-motion Play, the playback speed
changes. Two speeds are available. With each
press the indication changes as follows:
To go to the next chapter/track/scene
During playback, briefly turn the Playback
Dial clockwise to go to the next chapter/track/
scene, or counterclockwise to go to the
previous ones.
Playback direction
2
y 1
To locate a point quickly (Search)
Opposite direction (DVD VIDEO/DVD-RW
only)
During playback, turn and hold the Playback
Dial clockwise to locate a point in the
playback direction, or counterclockwise to
locate a point in the opposite direction. When
you find the point you want, release the dial to
return to normal playback speed.
2
y 1
The “2 y”/“2
than “1 y”/“1
” playback speed is slower
.”
Note
For DATA CDs, this function works only for DivX
video files.
Playing one frame at a time
(Freeze Frame)
When the player is in the pause mode, press
(step) to go to the next frame. Press
(step) to go to the preceding frame
(DVD VIDEO/DVD-RW only). To return to
normal playback, press H.
Notes
• You cannot search for a still picture on a DVD-
RW in VR mode.
• For DATA CDs, this function works only for
DivX video files.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
◆ When playing a DVD VIDEO/DVD-RW
TITLE
Searching for a Title/
Chapter/Track/Scene,
etc. (Search mode)
CHAPTER
TIME/TEXT
Select “TIME/TEXT” to search for a
starting point by inputting the time code.
◆ When playing a VIDEO CD or Super
VCD without PBC playback
TRACK
INDEX
You can search a DVD by title or chapter, and
you can search a VIDEO CD/Super Audio
CD/CD/DATA CD/DATA DVD by track,
index, or scene. As titles and tracks are
assigned unique numbers on the disc, you can
select the desired one by entering its number.
You can also search for a scene using the time
code.
◆ When playing a VIDEO CD or Super
VCD with PBC Playback
SCENE
◆ When playing a Super Audio CD/CD
TRACK
◆ When playing a DATA CD/DATA DVD
ALBUM
Number
buttons
TRACK (MP3 audio tracks
only)
FILE (JPEG image files, and
DivX video files only)
CLEAR
SEARCH
MODE
3
4
Select the number of the title,
track, scene, time code, etc. you
want by pressing the number
buttons to select the digit.
ENTER
◆ When you select
TIME/TEXT
For example, to find the scene at 2 hours,
10 minutes, and 20 seconds after the
beginning, enter “21020.”
1
2
Press SEARCH MODE.
◆ If you make a mistake
Cancel the number by pressing CLEAR,
then select another number.
The following display appears.
“-- ( )” appears next to the icon (
**
**
refers to a number). The number in
parentheses indicates the total number of
titles, tracks, indexes, scenes, etc., of the
disc.
Press ENTER.
The player starts playback from the
selected number.
– –
(
)
10
Press SEARCH MODE repeatedly
to select a search method.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
To turn off the display
Press SEARCH MODE repeatedly until the
display is turned off.
Searching by Scene
(PICTURE NAVIGATION)
z Hints
• When the Control Menu display is turned off, you
can search for a chapter (DVD VIDEO/DVD-
RW), track (Super Audio CD/CD), or file (DATA
CD (DivX video)/DATA DVD) by pressing the
number buttons and ENTER.
You can divide the screen into 9 subscreens
and find the desired scene quickly.
• You can display the first scene of titles, chapters,
or tracks recorded on the disc on a screen divided
into 9 sections. You can start playback directly by
selecting one of the scenes. For details, see
PICTURE
NAVI
Notes
• The title, chapter, or track number displayed is the
same number recorded on the disc.
• You cannot search for a scene on a DVD+RW
using the time code.
ENTER
C/X/x/c
DISPLAY
O RETURN
1
Press PICTURE NAVI during
playback.
The following display appears.
ENTER
CHAPTER VIEWER
2
Press PICTURE NAVI repeatedly to
select an item.
• CHAPTER VIEWER (DVD VIDEO
only): displays the first scene of each
chapter.
• TITLE VIEWER (DVD VIDEO only):
displays the first scene of each title.
• TRACK VIEWER (VIDEO CD/
Super VCD only): displays the first
scene of each track.
,continued
47
Download from Www.Somanuals.com. All Manuals Search And Download.
3
4
Press ENTER.
The first scene of each chapter, title, or
track appears as follows.
1
4
7
2
5
8
3
6
9
PressC/X/x/ctoselect achapter,
title, or track, and press ENTER.
Playback starts from the selected scene.
To return to normal play during setting
Press O RETURN or DISPLAY.
z Hint
If there are more than 9 chapters, titles, or tracks, V
is displayed at the bottom right of the screen.
To display the additional chapters, titles, or tracks,
select the bottom scenes and press x. To return to
the previous scene, select the top scenes and press
X.
Note
Depending on the disc, you may not be able to select
some items.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
◆ When playing a DVD VIDEO or DVD-
RW
Viewing Information About the
Disc
• T : : (hours: minutes: seconds)
Playing time of the current title
* * *
• T– : :
* * *
Checking the Playing
Time and Remaining
Time
Remaining time of the current title
• C : :
* * *
Playing time of the current chapter
• C– : :
* * *
Remaining time of the current chapter
◆ When playing a VIDEO CD or Super
VCD (with PBC functions)
•
:
(minutes: seconds)
You can check the playing time and
remaining time of the current title, chapter, or
track. Also, you can check the DVD/Super
Audio CD/CD text, track name (MP3 audio),
or file name (DivX video) recorded on the
disc.
* *
Playing time of the current scene
◆ When playing a VIDEO CD (without
PBC functions), Super Audio CD, or CD
• T
:
(minutes: seconds)
* *
Playing time of the current track
• T– :
* *
TV/DVD
switch
Remaining time of the current track
• D
:
* *
Playing time of the current disc
• D– :
* *
TIME/TEXT
Remaining time of the current disc
◆ When playing a Super VCD (without
PBC functions)
• T
:
(minutes: seconds)
* *
Playing time of the current track
◆ When playing a DATA CD (MP3 audio)
• T
:
(minutes: seconds)
* *
Playing time of the current track
◆ When playing a DATA CD (DivX video)/
DATA DVD (DivX video)
1
2
Make sure that the TV/DVD switch
is set to DVD. Press TIME/TEXT
during playback.
•
: : (hours: minutes: seconds)
Playing time of the current file
* * *
The following display appears.
T
1:01:57
Time
information
Press TIME/TEXT repeatedly to
change the time information.
The available time information depends
upon the type of disc you are playing.
,continued
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking the play information of
the Disc
Checking the information on the
front panel display
You can view the time information and text
displayed on the TV screen also on the front
panel display. The information on the front
panel display changes as follows when you
change the time information on your TV
screen.
To check the DVD/Super Audio CD/CD text
Press TIME/TEXT repeatedly in step 2 to
display text recorded on the DVD/Super
Audio CD/CD.
The DVD/Super Audio CD/CD text appears
only when text is recorded in the disc. You
cannot change the text. If the disc does not
contain text, “NO TEXT” appears.
When playing a DVD VIDEO or DVD-RW
Playing time of the current title
BRAHMS SYMPHONY
Remaining time of the current title
Playing time of the current chapter
To check DATA CD/DATA DVD album
name, etc.
By pressing TIME/TEXT while playing MP3
audio tracks on a DATA CD or DivX video
files on a DATA CD/DATA DVD, you can
display the name of the album/track/file, and
the audio bit rate (the amount of data per
second of the current audio) on your TV
screen.
Remaining time of the current
chapter
Bit rate*
T
17:30 128k
Text
JAZZ
RIVER SIDE
Current title and chapter number
Album name
Track/file name
(returns to top automatically)
* Appears when:
When playing a DATA CD (MP3 audio)
– playing an MP3 audio track on a DATA CD.
– playing a DivX video file that contains MP3
audio on a DATA CD/DATA DVD.
Playing time and number of the
current track
Track name
50
Download from Www.Somanuals.com. All Manuals Search And Download.
z Hints
When playing a DATA CD (DivX video), or
DATA DVD (DivX video)
• When playing VIDEO CDs with PBC functions,
the scene number or the playing time are
displayed.
Playing time of the current file
• Long text that does not fit in a single line will
scroll across the front panel display.
• You can also check the time information and text
The current file name
Notes
• Depending on the type of disc being played, the
disc text or track name may not be displayed.
• The player can only display the first level of the
disc text, such as the disc name or title.
• Playing time of MP3 audio tracks and DivX video
files may not be displayed correctly.
The current album and file number
(returns to top automatically)
•
If you play a disc containing JPEG image files
only, “NO AUDIO DATA” appears when
“MODE (MP3, JPEG)” is set to “AUTO,”
“JPEG” appears when “MODE (MP3, JPEG)” is
set to “IMAGE (JPEG)” in the front panel display.
When playing a VIDEO CD (without PBC
functions), Super Audio CD, or CD
Playing time and number of the
current track
Remaining time of the current
1
track*
Playing time of the disc
Remaining time of the disc
Text
2
Current track and index*
(returns to top automatically)
*1 When playing a Super Audio CD, the current
track is not displayed.
*2 The current track and index appear only when
playing a VIDEO CD or Super Audio CD.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
◆ When playing a DVD VIDEO
Depending on the DVD VIDEO, the
choice of language varies.
Sound Adjustments
When 4 digits are displayed, they
indicate a language code. See “Language
Code List” on page 98 to see which
language the code represents. When the
same language is displayed two or more
times, the DVD VIDEO is recorded in
multiple audio formats.
Changing the Sound
◆ When playing a DVD-RW
The types of sound tracks recorded on a
disc are displayed. The default setting is
underlined.
Example:
• 1: MAIN (main sound)
• 1: SUB (sub sound)
When playing a DVD VIDEO or DATA
DVD/DATA CD (DivX video files) recorded
in multiple audio formats (PCM, Dolby
Digital, MPEG audio, or DTS), you can
change the audio format. If the DVD VIDEO
is recorded with multilingual tracks, you can
also change the language.
• 1: MAIN+SUB (main and sub sound)
With CDs, DATA CDs, or VIDEO CDs, you
can select the sound from either the right or
left channel and listen to the sound of the
selected channel through both the right and
left speakers. For example, when playing a
disc containing a song with the vocals on the
right channel and the instruments on the left
channel, you can hear the instruments from
both speakers by selecting the left channel.
◆ When playing a VIDEO CD, CD, or
DATA CD (MP3 audio)
The default setting is underlined.
• STEREO: the standard stereo sound
• 1/L: the sound of the left channel
(monaural)
• 2/R: the sound of the right channel
(monaural)
◆ When playing a DATA CD (DivX
video), or DATA DVD (DivX video)
The choice of DATA CD or DATA DVD
audio signal formats differ, depending on
the DivX video file contained on the disc.
The format is shown in the display.
◆ When playing a Super VCD
The default setting is underlined.
• 1:STEREO: the stereo sound of the
audio track 1
• 1:1/L: the sound of the left channel of
the audio track 1 (monaural)
• 1:2/R: the sound of the right channel of
the audio track 1 (monaural)
• 2:STEREO: the stereo sound of the
audio track 2
• 2:1/L: the sound of the left channel of
the audio track 2 (monaural)
• 2:2/R: the sound of the right channel of
the audio track 2 (monaural)
1
2
Press
(audio) during playback.
The following display appears.
:
1
ENGLISH DOLBY DIGITAL 3/2.1
Press
(audio) repeatedly to
select the desired audio signal.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
◆When playing a DivX video file on a DATA
CD or a DATA DVD
Notes
• While playing a Super VCD on which the audio
track 2 is not recorded, no sound will come out
when you select “2:STEREO,” “2:1/L,” or
“2:2/R.”
Example:
MP3 audio
• You cannot change the sound for Super Audio
CDs.
1: MP3 128k
Bit rate
Checking the audio signal
format
You can check the audio signal format by
About audio signals
pressing
repeatedly during playback.
Audio signals recorded in a disc contain the
sound elements (channels) shown below.
Each channel is output from a separate
speaker.
The format of the current audio signal (Dolby
Digital, DTS, PCM, etc.) appears as shown
below.
• Front (L)
◆When playing a DVD VIDEO
• Front (R)
Example:
Dolby Digital 5.1 ch
• Centre
• Rear (L)
• Rear (R)
LFE (Low
• Rear (Monaural): This signal can be either
the Dolby Surround Sound processed
signals or the Dolby Digital sound’s
monaural rear audio signals.
• LFE (Low Frequency Effect) signal
Frequency Effect)
Rear (L/R)
:
3 / 2 .1
ENGLISH DOLBY DIGITAL
1
L
C
R
Front (L/R)
+ Centre
LFE
LS
RS
Currently playing
programm format
Example:
Dolby Digital 3 ch
Rear (Monaural)
Front (L/R)
:
2 / 1
2 SPANISH DOLBY DIGITAL
L
R
S
Currently playing
programm format
53
Download from Www.Somanuals.com. All Manuals Search And Download.
◆ For 4 to 6 speaker setups
(If you select “NONE” in the setting of
“REAR” in “SPEAKER SETUP”
modes.)
Surround Mode Settings
• NORMAL SURROUND
• ENHANCED SURROUND
• VIRTUAL REAR SHIFT
• VIRTUAL MULTI REAR
• VIRTUAL MULTI DIMENSION
You can enjoy surround sounds while playing
discs including Dolby Digital, DTS, and
MPEG audio DVDs, even if you have only 2
or 4 speakers. Select the surround mode that
best suits your speaker setup.
To cancel the setting
Select “OFF” in step 2.
For 2 speaker setups
When you connect a stereo TV or 2 front
speakers, TVS (TV Virtual Surround) lets
you enjoy surround sound effects by using
sound imaging to create virtual rear speakers
from the sound of the front speakers (L: left,
R: right) without using actual rear speakers.
TVS was developed by Sony to produce
surround sound for home use using just a
stereo TV.
SUR
If the player is set up to output the signal from
the DIGITAL OUT (OPTICAL or
COAXIAL) jack, the surround effect will be
heard only when “DOLBY DIGITAL” and
“DTS” are set to “D-PCM” and “MPEG” is
1
2
Press SUR during playback.
The following display appears.
TVS DYNAMIC
◆TVS DYNAMIC
Creates one set of virtual rear speakers from
the sound of the front speakers (L, R) without
using actual rear speakers (shown below).
This mode is effective when the distance
between the front L and R speakers is short,
such as with built-in speakers on a stereo TV.
Press SUR repeatedly to select
one of the surround modes.
See the explanations given for each item
in the following section.
TV
◆ For 2 speaker setups
• TVS DYNAMIC
• TVS WIDE
• TVS NIGHT
• TVS STANDARD
◆TVS WIDE
Creates five sets of virtual rear speakers from
the sound of the front speakers (L, R) without
using actual rear speakers (shown below).
This mode is effective when the distance
between the front L and R speakers is short,
such as with built-in speakers on a stereo TV.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
◆NORMAL SURROUND
TV
Software with 2 channel audio signals is
decoded with the Dolby Surround (Pro Logic)
decoder to create surround effects. The rear
speakers will emit identical monaural sounds.
If you are using a centre speaker, the
appropriate sounds for the centre speaker will
be delivered.
L
R
◆TVS NIGHT
Large sounds, such as explosions, are
suppressed, but quieter sounds are
unaffected. This feature is useful when you
want to hear the dialogue and enjoy the
surround sound effects of “TVS WIDE” at
low volume.
LS
RS
◆TVS STANDARD
◆ENHANCED SURROUND
Creates three sets of virtual rear speakers
from the sound of the actual front speakers (L,
R) as shown below. This mode is effective
when you use 2 separate front speakers.
Provides a greater sense of presence from a
Dolby Surround (Pro Logic) source with a
monaural rear channel signal. Produces a
stereo like effect in the rear channels.
L
R
◆VIRTUAL REAR SHIFT
Shifts the sound of the rear speakers away
from the actual speaker position.
The shift position differs according to
“REAR” or “SIDE” setting of the rear
REAR
L
R
L: Front speaker (left)
R: Front speaker (right)
: Virtual speaker
For 4 to 6 speaker setups
LS
RS
SIDE
L
R
You can enjoy the following surround effects
by using the 2 front speakers and 2 rear
speakers.
Connect the player to the amplifier (receiver)
LS
RS
with the
D-1
You can experience Dolby Surround (Pro
Logic) sounds or Digital Cinema Sound
(DCS). DCS uses sound imaging to shift the
sound of the rear speakers away from the
actual speaker position or create entire sets of
virtual rear speakers from one set of actual
rear speakers. “VIRTUAL REAR SHIFT,”
“VIRTUAL MULTI REAR,” and
“VIRTUAL MULTI DIMENSION” make
use of this technology.
,continued
55
Download from Www.Somanuals.com. All Manuals Search And Download.
◆VIRTUAL MULTI REAR
Creates an array of virtual rear speakers from
a single set of actual rear speakers.
The position of the virtual rear speakers
differs according to “REAR” or “SIDE”
L: Front speaker (left)
R: Front speaker (right)
LS: Rear speaker (left)
RS: Rear speaker (right)
: Virtual speaker
REAR
L
R
Notes
• When you select one of the surround modes, turn
off the surround setting of the connected TV or
amplifier (receiver).
• Not all discs will respond to the “TVS NIGHT”
function in the same way.
• To enjoy the multichannel audio through the
5.1CH OUTPUT jacks, correctly set each speaker
• When the playing signal does not contain a signal
for the rear speakers, you cannot hear the TVS
effect.
LS
RS
SIDE
L
R
• When you select one of the TVS modes, the
player does not output the sound of centre
speaker.
LS
RS
• Make sure that your listening position is between
and at an equal distance from your speakers, and
that the speakers are located in similar
surroundings.
◆VIRTUAL MULTI DIMENSION
• If you use the DIGITAL OUT (OPTICAL or
COAXIAL) jack and set “DOLBY DIGITAL” to
“DOLBY DIGITAL,” “DTS” to “DTS,” and
“MPEG” to “MPEG” in “AUDIO SETUP,”
sound will come from your speakers but it will not
have the SURROUND effect.
Creates an array of virtual rear speaker
positions higher than the listener from a
single set of actual rear speakers.
This mode creates five sets of virtual speakers
surrounding the listener at approximately a
30° angle of elevation. The effect differs
according to “REAR” or “SIDE” setting of
REAR
L
R
LS
RS
SIDE
L
R
LS
RS
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Displaying the Subtitles
Enjoying Movies
Changing the Angles
If subtitles are recorded on the discs, you can
change the subtitles or turn them on and off
whenever you want while playing the disc.
If various angles (multi-angles) for a scene
are recorded on the DVD VIDEO, “
”
appears in the front panel display. This means
that you can change the viewing angle.
1
2
Press
(subtitle) during
playback.
The following display appears.
1:ENGLISH
1
2
Press
(angle) during playback.
The number of the angle appears on the
display.
2
Press
(subtitle) repeatedly to
select a setting.
◆ When playing a DVD VIDEO
Select the language.
Depending on the DVD VIDEO, the
choice of language varies.
When 4 digits are displayed, they
indicate a language code. See “Language
Code List” on page 98 to see which
language the code represents.
Press
(angle) repeatedly to
select an angle number.
The scene changes to the selected angle.
Note
◆ When playing a DVD-RW
Select “ON.”
Depending on the DVD VIDEO, you may not be
able to change the angles even if multi-angles are
recorded on the DVD VIDEO.
◆ When playing a DATA CD (DivX
video), or DADA DVD
The choices of DATA CD or DATA
DVD subtitles differ, depending on the
DivX video file contained on the disc.
The choices are shown in the display.
,continued
57
Download from Www.Somanuals.com. All Manuals Search And Download.
To turn off the subtitles
Select “OFF” in step 2.
Adjusting the Playback
Picture (CUSTOM PICTURE MODE)
Notes
• Depending on the DVD VIDEO, you may not be
able to change the subtitles even if multilingual
subtitles are recorded on it. You also may not be
able to turn them off.
• With DATA CDs, subtitles can be changed for
DivX video files only.
• You can change the subtitles if the DivX video
file has an “.AVI” or “.DIVX” extension and
contains subtitle information within the same file.
You can adjust the video signal of the DVD,
VIDEO CD, DATA CD in JPEG format, or
DATA CD/DATA DVD containing DivX
video files from the player to obtain the
picture quality you want. Choose the setting
that best suits the programme you are
watching. When you select “MEMORY,”
you can make further adjustments to each
element of the picture (colour, brightness,
etc.).
PICTURE
MODE
C/X/x/c
ENTER
DISPLAY
O RETURN
1
Press PICTURE MODE during
playback.
The following display appears.
DYNAMIC 1
58
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Press C/c to adjust the picture
contrast.
2
Press PICTURE MODE repeatedly
to select the setting you want.
To go the next or previous picture item
without saving the current setting, press
X/x.
The default setting is underlined.
• STANDARD: displays a standard
picture.
• DYNAMIC 1: produces a bold
dynamic picture by increasing the
picture contrast and the colour
intensity.
3 Press ENTER.
The adjustment is saved, and
“BRIGHTNESS” adjustment bar
appears.
• DYNAMIC 2: produces a more
dynamic picture than DYNAMIC 1 by
further increasing the picture contrast
and colour intensity.
4 Repeat step 2 and 3 to adjust
“ BRIGHTNESS,” “COLOR,” and
“ HUE.”
• CINEMA 1: enhances details in dark
areas by increasing the black level.
• CINEMA 2: white colours become
brighter and black colours become
richer, and the colour contrast is
increased.
To turn off the display
Press O RETURN , or DISPLAY.
Note
• MEMORY: adjusts the picture in
greater detail.
The “BRIGHTNESS” setting is not effective if you
connect the player via the LINE OUT (VIDEO), S
VIDEO OUT, or LINE (RGB) - TV jack and select
“PROGRESSIVE AUTO” or “PROGRESSIVE
VIDEO” by using the PROGRESSIVE button on
the front panel.
z Hint
When you watch a movie, “CINEMA 1” or
“CINEMA 2” is recommended.
Adjusting the picture items in
“ MEMORY”
You can adjust each element of the picture
individually.
• PICTURE: changes the contrast
• BRIGHTNESS: changes the overall
brightness
• COLOR: makes the colours deeper or
lighter
• HUE: changes the colour balance
1 Press PICTURE MODE repeatedly to
select “MEMORY” and press ENTER.
The “PICTURE” adjustment bar appears.
PICTURE
0
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
Sharpening the Pictures
(SHARPNESS)
This setting is not effective if you connect the player
via the LINE OUT (VIDEO), S VIDEO OUT, or
LINE (RGB) - TV jack and select
“PROGRESSIVE AUTO” or “PROGRESSIVE
VIDEO” by using the PROGRESSIVE button on
the front panel.
You can enhance the outlines of images to
produce a sharper picture.
ENTER
X/x
DISPLAY
1
2
Press DISPLAY during playback.
The Control Menu appears.
Press X/x to select
(SHARPNESS), then press ENTER.
The options for “SHARPNESS” appear.
(
)
)
1 2 2 7
(
1 8 3 4
DVD VIDEO
T
1 : 3 2 : 5 5
OFF
1
2
OFF
3
4
Press X/x to select a level.
• 1: enhances the outline.
• 2: enhances the outline more than 1.
Press ENTER.
The selected setting takes effect.
To cancel the “ SHARPNESS” setting
Select “OFF” in step 3.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Press x to select “SETc”, then
press ENTER.
Adjusting the Delay
Between the Picture and
Sound (AV ALIGNMENT)
(DVP-NS955V only)
The “AV ALIGNMENT” adjustment bar
appears.
AV ALIGNMENT
0ms
When the sound does not match the pictures
on the screen, you can adjust the delay
between the picture and sound.
4
5
Press c repeatedly to adjust the
delay.
Each time you press C/c, the delay is
adjusted by 10 milliseconds.
CLEAR
Press ENTER.
The selected setting takes effect.
To reset the “AV ALIGNMENT” setting
Press CLEAR in step 4.
ENTER
C/X/x/c
Note
DISPLAY
This function is not effective if you use the
DIGITAL OUT (OPTICAL or COAXIAL) jack
and set “DOLBY DIGITAL,” “DTS,” or “MPEG”
in AUDIO SETUP to “DOLBY DIGITAL,”
1
2
Press DISPLAY during playback.
The Control Menu appears.
Press X/x to select
ALIGNMENT), then press ENTER.
(AV
The following display appears.
(
(
)
)
1
1
1 2
2 6
DVD VIDEO
T
0 : 0 0 : 0 2
0 ms
SET
61
Download from Www.Somanuals.com. All Manuals Search And Download.
– JPEG image files that conform to the DCF*
image file format.
* “Design rule for Camera File system”: Image
standards for digital cameras regulated by JEITA
(Japan Electronics and Information Technology
Industries Association).
Enjoying MP3 Audio and JPEG
Images
About MP3 Audio Tracks
and JPEG Image Files
Notes
• The player will play any data with the extension
“.MP3,” “.JPG,” or “.JPEG,” even if they are not
in MP3 or JPEG format. Playing these data may
generate a loud noise which could damage your
speaker system.
MP3 is audio compression technology that
satisfies the ISO/MPEG regulations. JPEG is
image compression technology.
You can play DATA CDs that contain MP3
audio tracks or JPEG image files.
• The player does not conform to audio tracks in
MP3PRO format.
• Some JPEG files cannot be played.
• You cannot play MP3 audio tracks/JPEG image
files in DATA CDs that contain DivX video files.
DATA CDs that the player can
play
You can play back DATA CDs (CD-ROMs/
CD-Rs/CD-RWs) recorded in MP3 (MPEG1
Audio Layer 3) and JPEG format. However,
the discs must be recorded according to
ISO 9660 Level 1, Level 2 or Joliet format for
the player to recognize the tracks (or files).
You can also play discs recorded in Multi
Session.
About playback order of albums,
tracks, and files
Albums play in the following order:
◆Structure of disc contents
Tree 1 Tree 2 Tree 3 Tree 4 Tree 5
ROOT
Refer to the instructions supplied with the
CD-R/CD-RW drives and the recording
software (not supplied) for details on the
recording format.
Note on Multi Session discs
If MP3 audio tracks or JPEG image files are
recorded in the first session, the player will
also play MP3 audio tracks or JPEG image
files in other sessions. If audio tracks and
images in Music CD format or Video CD
format are recorded in the first session, only
the first session will be played back.
Note
The player may not be able to play some DATA
CDs created in the Packet Write format.
MP3 audio track or JPEG image
file that the player can play
Album Track or file
The player can play the following tracks and
files:
– MP3 audio tracks with the extension
“.MP3.”
– JPEG image files with the extension
“.JPEG” or “.JPG.”
62
Download from Www.Somanuals.com. All Manuals Search And Download.
When you insert a DATA CD and press H,
the numbered tracks (or files) are played
sequentially, from 1 through 7. Any sub-
albums/tracks (or files) contained within a
currently selected album take priority over
the next album in the same tree. (Example: C
contains D so 4 is played before 5.)
Playing MP3 Audio
Tracks or JPEG Image
Files
You can play MP3 audio tracks and JPEG
image files on DATA CDs (CD-ROMs/CD-
Rs/CD-RWs).
When you press MENU and the list of album
are arranged in the following order:
A t B t C t D t F t G. Albums
that do not contain tracks (or files) (such as
album E) do not appear in the list.
z Hints
CLEAR
• If you add numbers (01, 02, 03, etc.) to the front
of the track/file names when you store the tracks
(or files) in a disc, the tracks and files will be
played in that order.
• Since a disc with many trees takes longer to start
playback, it is recommended that you create
albums with no more than two trees.
ZOOM
PICTURE
NAVI
x
./>
H
C/X/x/c
ENTER
Notes
O RETURN
• Depending on the software you use to create the
DATA CD, the playback order may differ from
the above illustration.
MENU
• The playback order above may not be applicable
if there are more than 200 albums and 300 tracks/
files in each album.
• The player can recognize up to 200 albums (the
player will count just albums, including albums
that do not contain MP3 audio tracks and JPEG
image files). The player will not play any albums
beyond the 200th album.
z Hint
You can view the disc information while playing
• Proceeding to the next or another album may take
some time.
Notes
• DATA CDs recorded in KODAK Picture CD
format automatically start playing when inserted.
• If no MP3 audio track or JPEG image file is
recorded on the DATA CD, “No audio data” or
“No image data” appears on the screen.
,continued
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting an album
Selecting an MP3 audio track
1 Press MENU.
1 After step 2 of “Selecting an album,”
press ENTER.
The list of albums on the disc appears.
When an album is being played, its title is
shaded.
The list of tracks in the album appears.
M Y F A V O U R I T E S O N G
(
)
1
2 5 6
(
)
3
3 0
W A L T Z F O R D E B B Y
M Y R O M A N C E
M I L E S T O N E S
M Y F U N N Y V A L E N T I N E
A U T U M L E A V E S
A L L B L U E S
R O C K B E S T H I T
K A R A O K E
M Y F A V O U R I T E S O N G
R & B
J A Z Z
C L A S S I C
S O M E D A Y M Y P R I N C E W...
S A L S A O F C U B A
B O S S A N O V A
2 Press X/x to select a track, and press
ENTER.
2 Press X/x to select the album you
want to play.
Playback starts from the selected track.
3 Press H.
Playback starts from the selected album.
To select MP3 audio tracks, see
To stop playback
Press x.
To go to the next or previous page
Press c or C.
To select JPEG image files, see
To return to the previous display
Press O RETURN.
To stop playback
Press x.
To go to the next or previous MP3 audio
track
Press > or . during playback. You can
select the first track of the next album by
pressing > during playback of the last
track of the current album.
Note that you cannot return to the previous
album by using ., and that you need to
select the previous album from the album list.
To go to the next or previous page
Press c or C.
To turn on or off the display
Press MENU repeatedly.
z Hints
• Of the selected album, you can select to play only
the MP3 audio tracks, JPEG image files, or both,
• During playback, you can press ALBUM +/– to
go to the next/previous album without using the
album list.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
To rotate a JPEG image
Selecting a JPEG image file
Press X/x while viewing the image. Each
time you press X, the image rotates
counterclockwise by 90 degrees.
To return to normal view, press CLEAR.
Note that the view also returns to normal if
you press C/c to go to the next or previous
image.
1 After step 2 of “ Selecting an album,”
press PICTURE NAVI.
The image files in the album appear in 16
subscreens. A scroll box is displayed on
the right.
Example: when X is pressed once.
Rotating direction
1
2
3
4
5
6
7
8
9
10
14
11
15
12
16
13
To display the additional image, select
the bottom images and press x. To return
to the previous image, select the top
images and press X.
To magnify a JPEG image (ZOOM)
Press ZOOM while viewing the image. You
can enlarge the image up to four times the
original size, and scroll using C/X/x/c.
To return to normal view, press CLEAR.
2 Press C/X/x/ctoselecttheimageyou
want to view, and press ENTER.
The selected image appears.
Example
◆When pressed once (x2)
The image enlarges twice the original size.
To go to the next or previous JPEG image
file
Press C or c during playback. You can select
the first file of the next album by pressing c
during playback of the last file of the current
album.
◆When pressed twice (x4)
The image enlarges four times the original
size.
Note that you cannot return to the previous
album by using C, and that you need to select
the previous album from the album list.
,continued
65
Download from Www.Somanuals.com. All Manuals Search And Download.
To stop viewing the JPEG image
Press x.
Enjoying JPEG Images as
a Slide Show
z Hints
• While viewing JPEG image files, you can set
(page 60).
You can play JPEG image files on a DATA
CD successively as a slide show.
• You can view JPEG images files without MP3
audio by setting “MODE (MP3, JPEG)” to
• The date the picture was taken is displayed beside
no date may appear depending on the digital
camera.
Note
PICTURE NAVI does not work if “AUDIO (MP3)”
H
x
X/x
MENU
1
Press MENU.
The list of albums on the DATA CD
appears.
(
)
3
3 0
R O C K B E S T H I T
K A R A O K E
M Y F A V O U R I T E S O N G
R & B
J A Z Z
C L A S S I C
S A L S A O F C U B A
B O S S A N O V A
2
3
Press X/x to select an album.
Press H.
The JPEG images in the selected album
start playing as a slide show.
To stop playback
Press x.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Press X/x to select “AUTO” (default),
and press ENTER.
Notes
• The slide show stops when X/x or ZOOM is
pressed. To resume the slide show, press H.
• This function does not work if “MODE (MP3,
• AUTO: plays both the JPEG image files
and MP3 audio tracks in the same
album as a slide show.
• AUDIO (MP3): plays only MP3 audio
tracks continuously.
• IMAGE (JPEG): plays only JPEG
image files continuously.
Viewing a slide show with sound
(MODE (MP3, JPEG))
When JPEG image files and MP3 audio
tracks are placed in the same album, you can
enjoy a slide show with sound.
4 Press MENU.
The list of albums on the DATA CD
appears.
(
)
3
3 0
R O C K B E S T H I T
K A R A O K E
M Y F A V O U R I T E S O N G
R & B
J A Z Z
C L A S S I C
S A L S A O F C U B A
B O S S A N O V A
5 Press X/x to select the album that
contains both the MP3 audio tracks
and JPEG images you want to play.
H
ENTER
MENU
X/x
6 Press H.
DISPLAY
A slide show starts with sound.
1 Press DISPLAY during stop mode.
z Hints
The Control Menu appears.
• To repeat both MP3 audio tracks and JPEG image
files in a single album, repeat the same MP3 audio
track or album when “MODE (MP3, JPEG)” is set
to “AUTO.” See “Playing repeatedly (Repeat
• The player recognizes a maximum of 200 albums
regardless of the selected mode. Of each album,
the player recognizes up to 300 MP3 audio tracks
and 300 JPEG image files when “AUTO” is
selected, 600 MP3 audio tracks when “AUDIO
(MP3)” is selected, 600 JPEG image files when
“IMAGE (JPEG)” is selected.
2 Press X/x to select
(MP3, JPEG)), and press ENTER.
The options for “MODE (MP3, JPEG)”
appear.
(MODE
(
)
)
1 2 2 7
(
1 8 3 4
DATA CD MP3
T
3 2 : 5 5
AUTO
AUTO
AUDIO (MP3)
IMAGE (JPEG)
Notes
• This function does not work if the MP3 audio
tracks and JPEG image files are not placed in the
same album.
• If playing time of JPEG image or MP3 audio is
longer than the other, the longer one continues
without sound or image.
• If you play large MP3 track data and JPEG image
data at the same time, the sound may skip. It is
recommended that you set the MP3 bit rate to 128
kbps or lower when creating the file. If the sound
still skips, then reduce the size of the JPEG file.
,continued
67
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Press ENTER.
Setting the pace for a slide show
(INTERVAL)
Note
You can set the time the slides are displayed
on the screen.
Some JPEG files, especially progressive JPEG files
or JPEG files of 3,000,000 pixels or more, may take
longer to display than others, which may make the
duration seem longer than the setting you selected.
Selectingtheslides’ appearance
(EFFECT)
You can select the way the slides are
displayed during a slide show.
ENTER
X/x
DISPLAY
1 Press DISPLAY twice while viewing a
JPEG image or when the player is in
stop mode.
ENTER
The Control Menu appears.
X/x
2 Press X/x to select
DISPLAY
(INTERVAL), then press ENTER.
The options for “INTERVAL” appear.
1 Press DISPLAY twice while viewing a
JPEG image or when the player is in
stop mode.
3 ( 12)
1(
2 9 / 1 0 / 2 0 0 4
NORMAL
NORMAL
FAST
4)
DATA CD JPEG
2 PressX/xto select
(EFFECT),
SLOW1
SLOW2
then press ENTER.
The options for “EFFECT” appear.
3 ( 12)
1(
4)
DATA CD JPEG
2 3 / 1 0 / 2 0 0 4
3 Press X/x to select a setting.
The default setting is underlined.
• NORMAL: sets the duration to between
6 to 9 seconds.
MODE1
MODE1
MODE2
MODE3
MODE4
MODE5
OFF
• FAST: sets a duration shorter than
NORMAL.
• SLOW1: sets a duration longer than
NORMAL.
EFFECT
• SLOW2: sets a duration longer than
SLOW1.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Press X/x to select a setting.
The default setting is underlined.
• MODE1: the image sweeps in from top
to bottom.
• MODE2: the image sweeps in from left
to right.
• MODE3: the image stretches out from
the centre of the screen.
• MODE4: the images randomly cycle
through the effects.
• MODE5: the next image slides over the
previous image.
• OFF: turns off this function.
4 Press ENTER.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
DivX video files that the player
can play
®
Enjoying DivX Videos
The player can play data that is recorded in
DivX format, and which has the extension
“.AVI,” or “.DIVX.” The player will not play
files with the extension “.AVI” or “.DIVX” if
they do not contain a DivX video.
About DivX Video Files
®
DivX is a video file compression
technology, developed by DivXNetworks,
®
Inc. This product is an official DivX
z Hint
certified product.
For details about playable MP3 audio tracks or
JPEG image files on DATA CDs, see “DATA CDs
You can play DATA CDs and DATA DVDs
that contain DivX video files.
DATA CDs and DATA DVDs that
the player can play
Notes
• The player may not play a DivX video file when
the file has been combined from two or more
DivX video files.
• The player cannot play a DivX video file of size
more than 720 (width) × 576 (height)/2 GB.
• Depending on the DivX video file, the picture
may be unclear or the sound may skip.
• The player cannot play some DivX video files that
are longer than 3 hours.
Playback of DATA CDs (CD-ROMs/CD-Rs/
CD-RWs) and DATA DVDs (DVD-Rs/
DVD-RWs/DVD+Rs/DVD+RWs) on this
player is subject to certain conditions:
– With DATA CDs that contain DivX video
files in addition to MP3 audio tracks or
JPEG image files, the player plays only the
DivX video files.
– With DATA DVDs, the player plays DivX
video files only. Any data other than DivX
video file, such as MP3 audio tracks and
JPEG image files, are not played.
However, this player only plays DATA CDs
whose logical format is ISO 9660 Level 1/
Level 2 or Joliet, and DATA DVDs of
Universal Disk Format (UDF).
You can also play DATA CDs recorded in
DVDs recorded in Multi Session are not
playable.
Refer to the instructions supplied with the
disc drives and the recording software (not
supplied) for details on the recording format.
About playback order of data on DATA CDs
or DATA DVDs
See “About playback order of albums, tracks
order may not be applicable, depending on
the software used for creating the DivX video
file, or if there are more than 200 albums and
600 DivX video files in each album.
Note
The player may not be able to play some DATA
CDs/DATA DVDs created in the Packet Write
format.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting an album
Playing DivX Video Files
1 Press MENU.
A list of albums on the disc appears. Only
albums that contain DivX video files are
listed.
You can play DivX video files on DATA CDs
(CD-ROMs/CD-Rs/CD-RWs) and DATA
DVDs (DVD-Rs/DVD-RWs/DVD+Rs/
DVD+RWs).
(
)
3
3
S U M M E R 2 0 0 3
N E W Y E A R ' S D A Y
M Y F A V O U R I T E S
2 Press X/x to select the album you
want to play.
./>
3 Press H.
Playback starts from the selected album.
To select DivX video files, see “Selecting
H
x
C/X/x/c
ENTER
DISPLAY
O RETURN
To stop playback
MENU
Press x.
To go to the next or previous page
Press c or C.
z Hint
You can view the disc information while playing a
To turn the display on or off
Press MENU repeatedly.
Notes
• If there are no DivX video files recorded on a
DATA DVD, a message appears to indicate that
the disc is not playable.
• Depending on the DivX video file, the picture
may pause or be unclear. In which case, it is
recommended that you create the file at a lower
bit rate. If the sound is still noisy, MP3 is the
recommended audio format. Note, however, this
player does not conform to WMA (Windows
Media Audio) format.
• Because of the compression technology used for
DivX video files, it may take some time after you
press H for the picture to appear.
• Depending on the DivX video file, the sound may
not match the pictures on the screen.
,continued
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting a DivX video file
1 After step 2 of “ Selecting an album,”
press ENTER.
The list of files in the album appears.
M Y F A V O U R I T E S
(
)
1
2
H A W A I I 2 0 0 4
V E N U S
2 Press X/x to select a file, and press
ENTER.
The selected file starts playing.
To stop playback
Press x.
To go to the next or previous page
Press c or C.
To return to the previous display
Press O RETURN.
To go to the next or previous DivX video
file without displaying the above file list
You can select the next or previous DivX
video file in the same album by pressing >
or ..
You can also select the first file of the next
album by pressing > during playback of
the last file of the current album. Note that
you cannot return to the previous album by
using .. To return to the previous album,
select it from the album list.
z Hint
If the number of viewing times is preset, you can
play the DivX video files as many times as the
preset number. The following occurrences are
counted:
– when the player is turned off. This includes when
the player is automatically turned off by the Auto
Power Off function. Press X instead of x when
you want to stop viewing.
– when the disc tray is opened.
– when another file is played.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Press DISPLAY while the player is in
stop mode.
Using Various Additional
Functions
The Control Menu appears.
3 Press X/x to select
(PARENTAL CONTROL), then press
ENTER.
Locking Discs (CUSTOM
PARENTAL CONTROL, PARENTAL
CONTROL)
The options for “PARENTAL
CONTROL” appear.
(
)
)
1 2 2 7
(
1 8 3 4
DVD VIDEO
You can set two kinds of playback restrictions
for a disc.
T
1 : 3 2 : 5 5
• Custom Parental Control
ON
You can set playback restrictions so that the
player will not play inappropriate discs.
• Parental Control
PLAYER
PASSWORD
OFF
Playback of some DVD VIDEOs can be
limited according to a predetermined level
such as the age of the users. Scenes may be
blocked or replaced with different scenes.
The same password is used for both Parental
Control and Custom Parental Control.
4 Press X/x to select “ ON t,” then
press ENTER.
◆ If you have not entered a password
The display for registering a new
password appears.
Custom Parental Control
PARENTAL CONTROL
Enter a new 4-digit password,
You can set the same Custom Parental
Control password for up to 40 discs. When
you set the 41st-disc, the first disc is
cancelled.
ENTER
then press
.
Enter a 4-digit password using the
number buttons, then press ENTER.
The display for confirming the password
appears.
Number
buttons
◆ When you have already registered a
password
The display for entering the password
appears.
x
ENTER
PARENTAL CONTROL
X/x
Enter password, then press ENTER
.
DISPLAY
1 Insert the disc you want to lock.
If the disc is playing, press x to stop
playback.
,continued
73
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Enterorre-enter your4-digit password
using the number buttons, then press
ENTER.
Parental Control (limited
playback)
“Custom parental control is set.” appears
and then the screen returns to the Control
Menu.
Playback of some DVD VIDEOs can be
limited according to a predetermined level
such as the age of the users. The
“PARENTAL CONTROL” function allows
you to set a playback limitation level.
To turn off the Custom Parental Control
function
1
2
3
Follow steps 1 to 3 of “Custom Parental
Control.”
Number
buttons
Press X/x to select “OFF t,” then press
ENTER.
Enter your 4-digit password using the
number buttons, then press ENTER.
To play a disc for which Custom Parental
Control is set
H
ENTER
1
Insert the disc for which Custom Parental
Control is set.
The “CUSTOM PARENTAL
CONTROL” display appears.
X/x
DISPLAY
1 Press DISPLAY while the player is in
stop mode.
CUSTOM PARENTAL CONTROL
The Control Menu appears.
Custom parental control is already
set. To play, enter your password
ENTER
2 Press X/x to select
(PARENTAL CONTROL), then press
ENTER.
and press
.
The options for “PARENTAL
CONTROL” appear.
2
Enter your 4-digit password using the
number buttons, then press ENTER.
The player is ready for playback.
(
)
)
1 2 2 7
(
1 8 3 4
DVD VIDEO
T
1 : 3 2 : 5 5
z Hint
If you forget your password, enter the 6-digit
number “199703” using the number buttons when
the “CUSTOM PARENTAL CONTROL” display
asks you for your password, then press ENTER.
The display will ask you to enter a new 4-digit
password.
ON
PLAYER
PASSWORD
OFF
3 Press X/x to select “ PLAYER t,”
then press ENTER.
◆ If you have not entered a password
The display for registering a new
password appears.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Press X/x to select a geographic area
as the playback limitation level, then
press ENTER.
PARENTAL CONTROL
Enter a new 4-digit password,
The area is selected.
ENTER
then press
.
When you select “OTHERS t,” select
and enter a standard code in the table on
page 76 using the number buttons.
7 Press X/x to select “ LEVEL,” then
press ENTER.
Enter a 4-digit password using the
number buttons, then press ENTER.
The display for confirming the password
appears.
The selection items for “LEVEL” are
displayed.
◆ When you have already registered a
password
The display for entering the password
appears.
PARENTAL CONTROL
LEVEL:
STANDARD:
OFF
OFF
8:
7: NC17
6:
5:
R
PARENTAL CONTROL
Enter password, then press ENTER
.
8 Select the level you want using X/x,
then press ENTER.
Parental Control setting is complete.
PARENTAL CONTROL
LEVEL:
STANDARD:
4 Enterorre-enter your4-digit password
using the number buttons, then press
ENTER.
4: PG13
USA
The display for setting the playback
limitation level appears.
The lower the value, the stricter the
limitation.
PARENTAL CONTROL
LEVEL:
STANDARD:
OFF
USA
To turn off the Parental Control function
Set “LEVEL” to “OFF” in step 8.
To play a disc for which Parental Control is
set
5 Press X/x to select “STANDARD,”
then press ENTER.
1
Insert the disc and press H.
The display for entering your password
appears.
The selection items for “STANDARD”
are displayed.
2
Enter your 4-digit password using the
number buttons, then press ENTER.
The player starts playback.
PARENTAL CONTROL
LEVEL:
STANDARD:
OFF
USA
USA
OTHERS
,continued
75
Download from Www.Somanuals.com. All Manuals Search And Download.
z Hint
Area Code
If you forget your password, remove the disc and
repeat steps 1 to 3 of “Parental Control (limited
playback).” When you are asked to enter your
password, enter “199703” using the number
buttons, then press ENTER. The display will ask
you to enter a new 4-digit password. After you enter
a new 4-digit password, replace the disc in the
player and press H. When the display for entering
your password appears, enter your new password.
Standard
Argentina
Australia
Austria
Code number
2044
2047
2046
2057
2070
2079
2090
2092
2115
2165
2174
2109
2248
2238
2254
2276
2304
2363
2362
2376
2390
2379
2427
2424
2436
2489
2501
2149
2499
2086
2528
2184
Belgium
Brazil
Canada
Notes
• When you play discs which do not have the
Parental Control function, playback cannot be
limited on this player.
• Depending on the disc, you may be asked to
change the parental control level while playing
the disc. In this case, enter your password, then
change the level. If the Resume Play mode is
cancelled, the level returns to the previous level.
Chile
China
Denmark
Finland
France
Germany
India
Indonesia
Italy
Japan
Korea
Malaysia
Mexico
Netherlands
New Zealand
Norway
Pakistan
Philippines
Portugal
Russia
Singapore
Spain
Sweden
Switzerland
Thailand
United Kingdom
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the password
ControllingYourTVorAV
Amplifier(Receiver)With
the Supplied Remote
1 Press DISPLAY while the player is in
stop mode.
The Control Menu appears.
2 Press X/x to select
(PARENTAL CONTROL), then press
ENTER.
By adjusting the remote signal, you can
control your TV with the supplied remote. If
you connect the player to an AV amplifier
(receiver), you can control the volume with
the supplied remote.
The options for “PARENTAL
CONTROL” appear.
3 Press X/x to select “ PASSWORD
t,” then press ENTER.
The display for entering the password
appears.
Notes
• Depending on the connected unit, you may not be
able to correctly control your TV or AV amplifier
(receiver) using some of the buttons below.
• If you enter a new code number, the code number
previously entered will be erased.
4 Enter your 4-digit password using the
number buttons, then press ENTER.
• When you replace the batteries of the remote, the
code number you have set may be reset to the
default setting. Set the appropriate code number
again.
5 Enter anew 4-digitpasswordusing the
number buttons, then press ENTER.
6 To confirm your password, re-enter it
using the number buttons, then press
ENTER.
Controlling TVs with the remote
TV/DVD
switch
If you make a mistake entering your
password
Press C before you press ENTER and input
the correct number.
[/1
2 +/–
Number
buttons
t (TV/video)
-/--
1 Slide the TV/DVD switch to TV.
2 While holding down [/1, press the
number buttons to select the
manufacturer’s code for your TV (see
the table below).
3 Release [/1.
,continued
77
Download from Www.Somanuals.com. All Manuals Search And Download.
When the TV/DVD switch is set to TV, the
remote performs the following:
Controlling the volume of your
AV amplifier (receiver) with the
remote
[/1
Turn the TV on or off
2 (volume) +/– Adjust the volume of the TV
Number buttons Select the programme
TV/DVD
switch
"/1
and -/--
position of the TV
t (TV/video) Switch the TV’s input source
between the TV and other
2 +/–
Number
buttons
input sources
Code numbers of controllable TVs
If more than one code number is listed, try
entering them one at a time until you find the
one that works with your TV.
Manufacturer
Sony
Code number
01 (default)
1 Slide the TV/DVD switch to DVD.
Aiwa
01 (default)
2 Hold down [/1, and enter the
manufacturer code (see the table
below)for your AV amplifier (receiver)
using the number buttons.
Grundig
Hitachi
Loewe
Nokia
11
23, 24, 72
06, 45
3 Release [/1.
15, 16, 69, 73
The 2 (volume) +/– buttons control the
AV amplifier’s volume.
Panasonic
Philips
Saba
17, 49
06, 07, 08, 23, 45, 72
◆ If you want to control the TV’s volume
Slide the TV/DVD switch to TV.
12, 13, 36, 43, 74, 75
Samsung
Sanyo
06, 22, 23, 71, 72
25
Code numbers of controllable AV
amplifiers (receivers)
Sharp
29
If more than one code number is listed, try
entering them one at a time until you find the
one that works with your AV amplifier
(receiver).
Telefunken
Thomson
Toshiba
LG
12, 13, 36, 43, 74, 75
12, 13, 43, 74, 75
38
06
33
Manufacturer
Sony
Code number
78, 79, 80, 91
84, 85, 86
92, 93
JVC
Denon
Kenwood
Onkyo
81, 82, 83
99
Pioneer
Sansui
87
Technics
Yamaha
97, 98
94, 95, 96
78
Download from Www.Somanuals.com. All Manuals Search And Download.
z Hint
If you want to control the TV’s volume even when
the TV/DVD switch is set to DVD, repeat the steps
above and enter the code number 90 (default).
79
Download from Www.Somanuals.com. All Manuals Search And Download.
3
4
Press X/x to select “CUSTOM,”
then press ENTER.
Settings and Adjustments
The Setup Display appears.
LANGUAGE SETUP
OSD:
MENU:
AUDIO:
SUBTITLE:
Using the Setup Display
ENGLISH
ENGLISH
ORIGINAL
ENGLISH
By using the Setup Display, you can make
various adjustments to items such as picture
and sound. You can also set a language for the
subtitles and the Setup Display, among other
things.
For details on each Setup Display item, see
Press X/x to select the setup item
from the displayed list:
Note
“ LANGUAGE SETUP,” “ SCREEN
SETUP,” “ CUSTOM SETUP,”
“ AUDIO SETUP,” or “ SPEAKER
SETUP.” Then press ENTER.
Playback settings stored in the disc take priority
over the Setup Display settings and not all of the
functions described may work.
The Setup item is selected.
Example: “SCREEN SETUP”
Selected item
SCREEN SETUP
TV TYPE:
16:9
ON
SCREEN SAVER:
BACKGROUND:
LINE:
JACKET PICTURE
VIDEO
FULL
4:3 OUTPUT:
ENTER
X/x
DISPLAY
Setup items
5
Press X/x to select an item, then
press ENTER.
1
2
Press DISPLAY when the player is
in stop mode.
The options for the selected item appear.
Example: “TV TYPE”
The Control Menu appears.
Press X/x to select
(SETUP), then press ENTER.
SCREEN SETUP
TV TYPE:
SCREEN SAVER:
BACKGROUND:
LINE:
16:9
16:9
4:3 LETTER BOX
4:3 PAN SCAN
FULL
The options for “SETUP” appear.
4:3 OUTPUT:
(
)
DVD VIDEO
47
Options
QUICK
CUSTOM
RESET
QUICK
80
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Press X/x to select a setting, then
press ENTER.
Setting the Display or
Sound Track Language
(LANGUAGE SETUP)
The setting is selected and setup is
complete.
Example: “4:3 PAN SCAN”
Selected setting
“LANGUAGE SETUP” allows you to set
various languages for the on-screen display or
sound track.
SCREEN SETUP
TV TYPE:
4:3 PAN SCAN
ON
SCREEN SAVER:
BACKGROUND:
LINE:
JACKET PICTURE
VIDEO
Select “LANGUAGE SETUP” in the Setup
Display. To use the display, see “Using the
FULL
4:3 OUTPUT:
LANGUAGE SETUP
OSD:
MENU:
AUDIO:
SUBTITLE:
ENGLISH
ENGLISH
ORIGINAL
ENGLISH
To enter the Quick Setup mode
Select “QUICK” in step 3. Follow from step
5 of the Quick Setup explanation to make
◆ OSD (On-Screen Display)
Switches the display language on the screen.
To reset all of the “ SETUP” settings
1
Select “RESET” in step 3 and press
ENTER.
◆ MENU (DVD VIDEO only)
You can select the desired language for the
disc’s menu.
2
Select “YES” using X/x.
You can also quit the process and return
to the Control Menu by selecting “NO”
here.
◆ AUDIO (DVD VIDEO only)
Switches the language of the sound track.
When you select “ORIGINAL,” the language
given priority in the disc is selected.
3
Press ENTER.
89 return to the default settings. Do not
press [/1 while resetting the player,
which takes a few seconds to complete.
◆ SUBTITLE (DVD VIDEO only)
Switches the language of the subtitle recorded
on the DVD VIDEO.
When you select “AUDIO FOLLOW,” the
language for the subtitles changes according
to the language you selected for the sound
track.
z Hint
If you select “OTHERS t” in “MENU,”
“SUBTITLE,” or “AUDIO,” select and enter a
language code from “Language Code List” on
page 98 using the number buttons.
Note
If you select a language in “MENU,”
“SUBTITLE,” or “AUDIO” that is not recorded on
a DVD VIDEO, one of the recorded languages will
be automatically selected.
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
Settings for the Display
(SCREEN SETUP)
Depending on the DVD, “4:3 LETTER BOX” may
be selected automatically instead of “4:3 PAN
SCAN” or vice versa.
◆SCREEN SAVER
Choose settings according to the TV to be
connected.
The screen saver image appears when you
leave the player in pause or stop mode for 15
minutes, or when you play a Super Audio CD,
CD, or DATA CD (MP3 audio) for more than
15 minutes. The screen saver will help
prevent your display device from becoming
damaged (ghosting). Press H to turn off the
screen saver.
Select “SCREEN SETUP” in the Setup
Display. To use the display, see “Using the
The default settings are underlined.
SCREEN SETUP
TV TYPE:
16:9
SCREEN SAVER:
BACKGROUND:
LINE:
ON
ON
Turns on the screen saver.
Turns off the screen saver.
JACKET PICTURE
VIDEO
FULL
OFF
4:3 OUTPUT:
◆BACKGROUND
Selects the background colour or picture on
the TV screen when the player is in stop mode
or while playing a Super Audio CD, CD, or
DATA CD (MP3 audio).
◆ TV TYPE
Selects the aspect ratio of the connected TV
(4:3 standard or wide).
JACKET
PICTURE
The jacket picture (still picture)
appears, but only when the
jacket picture is already
16:9
Select this when you connect a
wide-screen TV or a TV with a
wide mode function.
recorded on the disc (CD-
4:3
LETTER
BOX
Select this when you connect a
4:3 screen TV. Displays a wide
picture with bands on the upper
and lower portions of the
screen.
EXTRA, etc.). If the disc does
not contain a jacket picture, the
“GRAPHICS” picture appears.
GRAPHICS A preset picture stored in the
player appears.
4:3
Select this when you connect a
BLUE
The background colour is blue.
PAN SCAN 4:3 screen TV. Automatically
displays the wide picture on the
entire screen and cuts off the
BLACK
The background colour is
black.
portions that do not fit.
◆LINE
Selects video signals output from the LINE
(RGB)-TV jack on the rear panel of the
player.
16:9
VIDEO
S VIDEO
RGB
Outputs video signals.
Outputs S video signals.
Outputs RGB signals.
4:3 LETTER BOX
4:3 PAN SCAN
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
Custom Settings (CUSTOM
SETUP)
• If your TV does not accept S video or the RGB
signals, no picture will appear on the TV screen,
even if you select “S VIDEO” or “RGB.” Refer to
the instructions supplied with your TV.
• When you select “RGB,” you cannot use the
PROGRESSIVE button or the COMPONENT
VIDEO OUT jacks.
Use this to set up playback related and other
settings.
Select “CUSTOM SETUP” in the Setup
Display. To use the display, see “Using the
◆ 4:3 OUTPUT
This setting is effective only when you set
“TV TYPE” in “SCREEN SETUP” to
“16:9.”
The default settings are underlined.
Adjust to watch 4:3 aspect ratio progressive
signals. If you can change the aspect ratio on
your progressive format (525p/625p)
compatible TV, change the setting on your
TV, not the player. This setting is effective
only when “PROGRESSIVE AUTO” or
“PROGRESSIVE VIDEO” is selected by
using the PROGRESSIVE button on the front
panel.
CUSTOM SETUP
AUTO PLAY:
OFF
BRIGHT
AUTO
ON
OFF
ON
DISPLAY:
PAUSE MODE:
PLAYBACK MEMORY:
TRACK SELECTION:
MULTI-DISC RESUME:
DivX:
Registration Code
◆ AUTO PLAY
Switches the Auto Play setting on or off. This
function is useful when the player is
connected to a timer (not supplied).
FULL
Select this when you can
change the aspect ratio on your
TV.
NORMAL
Select this when you cannot
change the aspect ratio on your
TV. Shows a 16:9 aspect ratio
signal with black bands on left
and right sides of the image.
OFF
ON
Switches this function off.
Automatically starts playback
when the player is turned on by
a timer (not supplied).
◆ DISPLAY (DVP-NS955V only)
Adjusts the lighting of the front panel display.
BRIGHT
DARK
Makes the lighting bright.
Makes the lighting dark.
16:9 aspect ratio TV
AUTO
DARK
Makes the lighting dark if you
do not operate the player or
remote for a short while.
AUTO OFF Turns off the lighting if you do
not operate the player or remote
for a while.
OFF
Turns off the lighting.
(FL OFF)
,continued
83
Download from Www.Somanuals.com. All Manuals Search And Download.
◆ DIMMER (DVP-LS785V only)
Adjusts the lighting of the front panel display.
◆TRACK SELECTION (DVD VIDEO only)
Gives the sound track which contains the
highest number of channels priority when you
play a DVD VIDEO on which multiple audio
formats (PCM, MPEG audio, DTS, or Dolby
Digital format) are recorded.
BRIGHT
DARK
Makes the lighting bright.
Makes the lighting dark.
AUTO
DARK
Makes the lighting dark if you
do not operate the player or
remote for a short while.
OFF
No priority given.
Priority given.
AUTO
◆ PAUSE MODE (DVD VIDEO/DVD-RW
only)
Selects the picture in pause mode.
Notes
• When you set the item to “AUTO,” the language
may change. The “TRACK SELECTION” setting
has higher priority than the “AUDIO” settings in
• If PCM, DTS, MPEG audio, and Dolby Digital
sound tracks have the same number of channels,
the player selects PCM, DTS, Dolby Digital, and
MPEG audio sound tracks in this order.
AUTO
The picture, including subjects
that move dynamically, is
output with no jitter. Normally
select this position.
FRAME
The picture, including subjects
that do not move dynamically,
is output in high resolution.
◆MULTI-DISC RESUME (DVD VIDEO/
VIDEO CD only)
Switches the Multi-disc Resume setting on or
off. Resume playback can be stored in
memory for up to 40 different DVD VIDEOs/
◆ PLAYBACK MEMORY (DVP-NS955V
only)
The player can store “CUSTOM PICTURE
MODE” and other settings of each disc for up
to 40 discs (Playback Memory).
Set this function “ON” or “OFF.”
ON
Stores the resume setting in
memory for up to 40 discs.
ON
Stores the settings in memory
when you eject the disc.
OFF
Does not store the resume
setting in memory. Playback
restarts at the resume point only
for the current disc in the player.
OFF
Does not store the settings in
memory.
The following settings are stored in memory.
◆DivX
Displays the registration code for this player.
For more information, go to
* DVD VIDEO/VIDEO CD/Super VCD only
http://www.divx.com on the Internet.
Note
The player can store the settings of up to 40 discs.
When you store the setting of disc number 41, the
first disc setting is cancelled.
84
Download from Www.Somanuals.com. All Manuals Search And Download.
WIDE
RANGE
Gives you the feeling of being
at a live performance.
Settings for the Sound
(AUDIO SETUP)
◆ AUDIO FILTER
Selects the digital filter to reduce noise above
22.05 kHz (Sampling frequency (Fs) of the
audio source is 44.1 kHz), 24 kHz (Fs is
48 kHz), or 48 kHz (Fs is above 96 kHz).
“AUDIO SETUP” allows you to set the sound
according to the playback and connection
conditions.
Select “AUDIO SETUP” in the Setup
Display. To use the display, see “Using the
SHARP
Provides a wide frequency range
and spatial feeling.
SLOW
Provides smooth and warm
sound.
The default settings are underlined.
AUDIO SETUP
AUDIO ATT:
AUDIO DRC:
AUDIO FILTER:
DOWNMIX:
OFF
STANDARD
SHARP
Note
DOLBY SURROUND
There may be little effect by changing the digital
filter depending on the disc or playback
environment.
DIGITAL OUT:
DOLBY DIGITAL:
MPEG:
DTS:
48kHz/96kHz PCM:
ON
D-PCM
PCM
D-PCM
48kHz/16bit
◆ DOWNMIX (DVD VIDEO/DVD-RW only)
Switches the method for mixing down to 2
channels when you play a DVD which has
rear sound elements (channels) or is recorded
in Dolby Digital format. For details on the
rear signal components, see “Checking the
audio signal format” (page 53). This function
affects the output of the following jacks:
– LINE OUT L/R (AUDIO) jacks
◆ AUDIO ATT (attenuation)
If the playback sound is distorted, set this
item to “ON.” The player reduces the audio
output level.
This function affects the output of the
following jacks:
– LINE OUT L/R (AUDIO) jacks
– LINE (RGB) – TV jack
– 5.1CH OUTPUT jacks
– LINE (RGB) – TV jack
– DIGITAL OUT (OPTICAL or COAXIAL)
jack when “DOLBY DIGITAL” and “DTS”
OFF
ON
Normally, select this position.
Select this when the playback sound
from the speakers is distorted.
DOLBY
SUR-
ROUND
Normally, select this position.
Multi-channel audio signals are
output to 2 channels for enjoying
surround sounds.
◆ AUDIO DRC (Dynamic Range Control)
(DVD VIDEO/DVD-RW only)
Makes the sound clear when the volume is
turned down when playing a DVD that
conforms to “AUDIO DRC.”
NORMAL Multi-channel audio signals are
downmixed to 2 channels for use
with your stereo.
This function affects the output from the
following jacks:
◆ DIGITAL OUT
– LINE OUT L/R (AUDIO) jacks
– LINE (RGB)-TV jacks
– 5.1 CH OUTPUT jacks
Selects if audio signals are output via the
DIGITAL OUT (OPTICAL or COAXIAL)
jack.
– DIGITAL OUT (OPTICAL or COAXIAL)
jack only when “DOLBY DIGITAL” is set
ON
Normally select this position. When
you select “ON,” see “Setting the
digital output signal” for further
settings.
STANDARD Normally, select this position.
OFF The influence of the digital circuit
TV MODE
Makes low sounds clear even if
you turn the volume down.
upon the analog circuit is minimal.
,continued
85
Download from Www.Somanuals.com. All Manuals Search And Download.
◆MPEG (DVD VIDEO/DVD-RW only)
Selects the type of MPEG audio signal.
Note
Super Audio CD audio signals are not output from
a DIGITAL OUT jack.
PCM
Select this when the player is
connected to an audio
component without a built-in
MPEG decoder. If you play
multi-channel MPEG audio
sound tracks, only the Front (L)
and Front (R) signals will be
output from your two front
speakers.
Setting the digital output signal
Switches the method of outputting audio
signals when you connect a component such
as an amplifier (receiver) or MD deck with a
digital input jack.
Select “DOLBY DIGITAL,” “MPEG,”
“DTS,” and “48kHz/96kHz PCM” after
setting “DIGITAL OUT” to “ON.”
MPEG
Select this when the player is
connected to an audio
component with a built-in
MPEG decoder.
AUDIO SETUP
AUDIO ATT:
AUDIO DRC:
AUDIO FILTER:
DOWNMIX:
OFF
STANDARD
SHARP
◆DTS
Selects the type of DTS audio signals.
DOLBY SURROUND
DIGITAL OUT:
DOLBY DIGITAL:
MPEG:
ON
D-PCM
PCM
D-PCM
D-PCM
Select this when the player is
connected to an audio
component without a built-in
DTS decoder.
DTS:
48kHz/96kHz PCM:
48kHz/16bit
DTS
Select this when the player is
connected to an audio
component with a built-in DTS
decoder.
If you connect a component that is
incompatible with the selected audio signal, a
loud noise (or no sound) may be heard from
the speakers, risking damage to your ears or
speakers.
◆48kHz/96kHz PCM (DVD VIDEO only)
Selects the sampling frequency of the audio
signal.
Note
effective if you use the DIGITAL OUT (OPTICAL
or COAXIAL) jack and set “DOLBY DIGITAL,”
“DTS,” or “MPEG” in AUDIO SETUP to
“DOLBY DIGITAL,” “DTS,” or “MPEG”
respectively.
48kHz/16bit The audio signals of DVD
VIDEOs are always converted
to 48 kHz/16 bit.
96kHz/24bit All types of signals including
96 kHz/24 bitare output in their
original format. However, if the
signal is encrypted for
◆ DOLBY DIGITAL (DVD VIDEO/DVD-RW
only)
Selects the type of Dolby Digital signal.
copyright protection purposes,
the signal is only output as
48 kHz/16 bit.
D-PCM
Select this when the player is
connected to an audio
Note
component without a built-in
Dolby Digital decoder. You can
select whether the signals
conform to Dolby Surround
(Pro Logic) or not by making
adjustments to the
The analogue audio signals from the LINE OUT L/
R (AUDIO) jacks and 5.1CH OUTPUT jacks are
not affected by this setting and keep their original
sampling frequency level.
“DOWNMIX” item in
DOLBY
DIGITAL
Select this when the player is
connected to an audio
component with a built-in
Dolby Digital decoder.
86
Download from Www.Somanuals.com. All Manuals Search And Download.
◆ SIZE
Selects the size of the speakers.
• FRONT
SettingsfortheSpeakers
(SPEAKER SETUP)
LARGE
SMALL
Normally select this position.
Select this when the speaker
cannot reproduce adequate bass
frequencies.
To obtain the best possible surround sound,
set the size of the speakers you have
connected and their distance from your
listening position. Then use the test tone to
adjust the volume of the speakers to the same
level.
This setting is effective when connecting the
speaker with 5.1 CH OUTPUT jacks (page
26).
• CENTER
LARGE
SMALL
Normally select this position.
Select this when the speaker
cannot reproduce adequate bass
frequencies.
NONE
Select this if you do not connect
a centre speaker.
Select “SPEAKER SETUP” in the Setup
Display. To use the display, see “Using the
items in the order that they are explained
below. The default settings are underlined.
Example: DVP-LS785V
• REAR
LARGE
(REAR/SIDE):Normally select
this position. Select according
to the rear speaker position*.
SPEAKER SETUP
SIZE:
SMALL
NONE
(REAR/SIDE): Select this
when the sound distorts or the
surround effects are difficult to
hear. Select according to the
rear speaker position*.
DISTANCE:
LEVEL(FRONT)
:
LEVEL(REAR)
TEST TONE:
FRONT:
CENTER:
REAR:
:
OFF
LARGE
LARGE
LARGE(REAR)
YES
Select this if you do not connect
rear speakers.
SUBWOOFER:
To make adjustments for Super Audio CDs
(DVP-NS955V only)
You can create two different Speaker Setup
settings, one for Super Audio CDs and one for
all other types of discs.
* Rear speaker position
Correctly specify the location of the rear speakers to
enjoy the surround effect.
• Set to “SIDE,” if the location of the rear speakers
corresponds to section A below.
• Set to “REAR,” if the location of the rear speakers
corresponds to section B below.
This setting affects only “VIRTUAL REAR
SHIFT,” “VIRTUAL MULTI REAR,” and
“VIRTUAL MULTI DIMENSION” mode
Audio CD Multi audio signals.
1
Follow steps 1 to 4 of “Using the Setup
SETUP” in the Setup Display.
2
3
Select “DVD” or “SUPER AUDIO CD”
using X/x, the press ENTER.
Set the following items in the order that
they are explained below. The default
settings are underlined.
To return to the default setting
Select the item, then press CLEAR. Note that
only the “SIZE” setting does not return to the
default setting.
90
45
20
,continued
87
Download from Www.Somanuals.com. All Manuals Search And Download.
• SUBWOOFER
CENTER (3 m) Set this within –1.6 and
+0.6 m of the “FRONT”
setting in 0.2 m increments.
For example, if “FRONT”
is set to 6 m, “CENTER”
can be set between 4.4 and
6.6 m.
YES
Select this if you connect a
subwoofer to output the LFE
(Low Frequency Effect) signals
from the subwoofer.
NONE
Select this if you do not connect
a subwoofer.
REAR (3 m)
Set this within –5 and
+0.6 m of the “FRONT”
setting in 0.2 m increments.
For example, if “FRONT”
is set to 6 m, “REAR” can
be set between 1 and 6.6 m.
Notes
• The cut off frequency for the subwoofer is fixed at
120 Hz.
• If your speakers are too small to reproduce low
bass frequencies, utilize a subwoofer for low
frequency sound. When you set the speaker
settings to “SMALL,” the bass redirection
circuitry will be activated and the bass
frequencies for the speakers are output from the
subwoofer.
SUBWOOFER Set this within –1.6 and
(3 m) (DVP- +0.6 m of the “FRONT”
NS955V only) setting in 0.2 m increments.
For example, if “FRONT”
is set to 6 m,
“SUBWOOFER” can be
• Even if there are fewer than 6 speakers connected,
the player distributes the audio signal components
to the front speakers.
set between 4.4 and 6.6 m.
Note
◆ DISTANCE
If each of the front or rear speakers are not placed at
an equal distance from your listening position, set
the distance according to the closest speaker.
Sets the distance from your listening position
to the speakers.
Set the distance to your front speakers in
“FRONT” first (A). Then adjust the values in
“CENTER” (centre speaker B), and
“REAR” (rear speaker C) , and
“SUBWOOFER” (DVP-NS955V only) (D)
to reflect the actual distance to your centre
speaker, rear speakers, and subwoofer.
◆LEVEL (FRONT)
Varies the level of the front speakers. Be sure
to set “TEST TONE” to “ON” for easy
adjustment.
The default adjustments are in parentheses.
L (0 dB)
Set this between –6 dB and
0 dB in 0.5 dB increments.
R (0 dB)
Set this between –6 dB and
0 dB in 0.5 dB increments.
B
D
CENTER
(0 dB)
Set this between –12 dB
and 0 dB in 0.5 dB
increments.
A
A
(1~15 m)
(1~15 m)
SUBWOOFER Set this between –15 dB
(DVP-NS955V: and +5 dB in 0.5 dB
DVD: –5 dB increments.
Super Audio
C
C
CD: 0 dB
DVP-LS785V:
–5 dB)
Be sure to change the value in the Setup
Display each time you move the speakers.
Start from the front speaker. The default
adjustments are in parentheses.
FRONT
(3 m)
Set this between 1 and 15 m
in 0.2 m increments.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
◆ LEVEL (REAR)
Varies the level of the rear speakers. Be sure
to set “TEST TONE” to “ON” for easy
adjustment.
The default adjustments are in parentheses.
L (0 dB)
Set this between –12 dB and
0 dB in 0.5 dB increments.
R (0 dB)
Set this between –12 dB and
0 dB in 0.5 dB increments.
To adjust the volume of all the speakers at
one time
Use the amplifier’s (receiver’s) volume
control.
◆ TEST TONE
The speakers will emit a test tone. Use this
when you use the 5.1CH OUTPUT jacks and
adjust “LEVEL (FRONT)” and “LEVEL
(REAR).”
OFF
The test tone is not emitted
from the speakers.
ON
The test tone is emitted from
each speaker in sequence while
adjusting level.
Adjusting the speaker volume
and level
1 Select “ SPEAKER SETUP” inthe Setup
Display.
2 Select “TEST TONE” and set to “ ON.”
You will hear the test tone from each
speaker in sequence.
3 From your listening position, select
“LEVEL (FRONT)” or “ LEVEL (REAR)”
and adjust the value using X/x.
The test tone is emitted from both left and
right speakers simultaneously.
4 Select “ TEST TONE” and set to “OFF”
to turn off the test tone.
Note
The test tone signals are not output from the
DIGITAL OUT jack.
89
Download from Www.Somanuals.com. All Manuals Search And Download.
, Even if your TV is compatible with
progressive format 525p/625p signals, the
image may be affected when you set the
player to progressive format. In this case,
select “NORMAL (INTERLACE)” using
the PROGRESSIVE button on the front
panel display so that the PROGRESSIVE
indicator turns off and the player is set to
normal (interlace) format.
, If you set “LINE” to “RGB” in “SCREEN
no component video signals.
, The VIDEO OFF function takes effect
(DVD-NS955V only).
Additional Information
Troubleshooting
If you experience any of the following
difficulties while using the player, use this
troubleshooting guide to help remedy the
problem before requesting repairs. Should
any problem persist, consult your nearest
Sony dealer.
Power
The picture does not fill the screen, even
though the aspect ratio is set in “TV TYPE”
under “SCREEN SETUP.”
, The aspect ratio of the disc is fixed on your
DVD.
The power is not turned on.
, Check that the mains lead is connected
securely.
Picture
The picture is black and white.
, Set “LINE” in “SCREEN SETUP” to an
, Depending on the TV, the picture on the
screen becomes black and white when you
play a disc recorded in the NTSC colour
system.
There is no picture/picture noise appears.
, Re-connect the connecting cord securely.
, The connecting cords are damaged.
and switch the input selector on your TV so
that the signal from the player appears on
the TV screen.
, Set “LINE” in “SCREEN SETUP” to an
, The disc is dirty or flawed.
, If the picture output from your player goes
through your VCR to get to your TV or if
you are connected to a combination TV/
VIDEO player, the copy-protection signal
applied to some DVD programmes could
affect picture quality. If you still experience
problems even when you connect your
player directly to your TV, try connecting
your player to your TV’s S VIDEO input
, If you are using a SCART cord, be sure to
use one that is fully wired (21-pins).
Sound
There is no sound.
, Re-connect the connecting cord securely.
, The connecting cord is damaged.
, The player is connected to the wrong input
jack on the amplifier (receiver) (page 24,
, The amplifier (receiver) input is not
correctly set.
, The player is in pause mode or in Slow-
motion Play mode.
, The player is in fast forward or fast reverse
mode.
, If the audio signal does not come through
the DIGITAL OUT (OPTICAL or
COAXIAL) jack, check the audio settings
, Super Audio CD audio signals are not
output from the DIGITAL OUT (OPTICAL
or COAXIAL) jack.
, The disc is recorded in a colour system that
is different from your TV.
, You have selected “PROGRESSIVE
(AUTO)” or “PROGRESSIVE (VIDEO)”
using the PROGRESSIVE button on the
front panel (the PROGRESSIVE indicator
lights up) even though your TV cannot
accept the progressive signal. In this case,
select “NORMAL (INTERLACE)” so that
the PROGRESSIVE indicator turns off.
90
Download from Www.Somanuals.com. All Manuals Search And Download.
, While playing a Super VCD on which the
audio track 2 is not recorded, no sound will
come out when you select “2:STEREO,”
“2:1/L,” or “2:2/R.”
The disc does not play.
, The disc is turned over.
Insert the disc with the playback side facing
down.
, The disc is skewed.
, The player cannot play certain discs
(page 7).
, The region code on the DVD does not match
the player.
Sound distortion occurs.
, Set “AUDIO ATT” in “AUDIO SETUP” to
“ON” (page 85).
, Moisture has condensed inside the player
The sound volume is low.
.
, The sound volume is low on some DVDs.
The sound volume may improve if you set
“AUDIO DRC” in “AUDIO SETUP” to
, The player cannot play a recorded disc that
.
The MP3 audio track cannot be played
, Set “AUDIO ATT” in “AUDIO SETUP” to
, The DATA CD is not recorded in an MP3
format that conforms to ISO 9660 Level 1/
Level 2 or Joliet.
, The MP3 audio track does not have the
extension “.MP3.”
, The data is not formatted in MP3 even
though it has the extension “.MP3.”
, The data is not MPEG1 Audio Layer 3 data.
, The player cannot play audio tracks in
MP3PRO format.
The surround effect is difficult to hear
when you are playing a Dolby Digital,
MPEG audio, or DTS sound track.
, Check the speaker connections and setting
, The 5.1 channel sound is not recorded on
the disc being played.
, “MODE (MP3, JPEG)” is set to “IMAGE
, The DATA CD contains a DivX video file.
, This player cannot play MP3 audio tracks
recorded on DATA DVDs.
The sound comes from the centre speaker
only.
, Depending on the disc, the sound may come
from the centre speaker only.
, Set the surround mode setting to “OFF”
The JPEG image file cannot be played
Operation
, The DATA CD is not recorded in a JPEG
format that conforms to ISO 9660 Level 1/
Level 2, or Joliet.
, The file has an extension other than
“.JPEG” or “.JPG.”
The remote does not function.
, The batteries in the remote are weak.
, There are obstacles between the remote and
the player.
, The distance between the remote and the
player is too far.
, The remote is not pointed at the remote
sensor on the player.
, The image is larger than 3072 (width) ×
2048 (height) in normal mode, or more than
3,300,000 pixels in progressive JPEG.
(Some progressive JPEG files cannot be
displayed even if the file size is within this
specified capacity.)
, The image does not fit the screen (the image
is reduced).
, “MODE (MP3, JPEG)” is set to “AUDIO
(MP3)” (page 67).
, The DATA CD contains a DivX video file.
, This player cannot play JPEG image files
recorded on DATA DVDs.
,continued
91
Download from Www.Somanuals.com. All Manuals Search And Download.
The MP3 audio tracks and JPEG image
The language for the sound track cannot
files start playing simultaneously.
, “MODE (MP3, JPEG)” is set to “AUTO.”
be changed.
, Try using the DVD’s menu instead of the
direct selection button on the remote
, Multilingual tracks are not recorded on the
DVD being played.
, The DVD prohibits the changing of the
language for the sound track.
The DivX video file cannot be played.
, The file is not created in DivX format.
, The file has an extension other than “.AVI”
or “.DIVX.”
, The DATA CD (DiviX video)/DATA DVD
is not created in a DivX format that
conforms to ISO 9660 Level 1/Level 2 or
Joliet/UDF.
, The DivX video file is larger than 720
(width) × 576 (height).
The subtitle language cannot be changed
or turned off.
, Try using the DVD’s menu instead of the
direct selection button on the remote
, Multilingual subtitles are not recorded on
the DVD being played.
, The DVD prohibits the changing of
subtitles.
The album/track/file names are not
displayed correctly.
, The player can only display numbers and
alphabet. Other characters are displayed as
The angles cannot be changed.
, Try using the DVD’s menu instead of the
direct selection button on the remote
, Multi-angles are not recorded on the DVD
being played.
“ ”.
*
The disc does not start playing from the
beginning.
, Programme Play, Shuffle Play, Repeat Play,
, The angle can only be changed when the
“
” indicator lights up on the front panel
display (page 10).
, The DVD prohibits changing of the angles.
The player starts playing the disc
automatically.
, The disc features an auto playback function.
, “AUTO PLAY” in “CUSTOM SETUP” is
The player does not operate properly.
, When static electricity, etc., causes the
player to operate abnormally, unplug the
player.
Playback stops automatically.
, While playing discs with an auto pause
signal, the player stops playback at the auto
pause signal.
Nothing is displayed in the front panel
display.
, “DISPLAY” in “CUSTOM SETUP” is set
to “OFF” or “AUTO OFF.” Set
“DISPLAY” to any setting other than
(DVP-NS955V only)
Some functions such as Stop, Search,
Slow-motion Play, Repeat Play, Shuffle
Play, or Programme Play cannot be
performed.
5 numbers or letters are displayed on the
, Depending on the disc, you may not be able
to do some of the operations above. Refer to
the operating manual that comes with the
disc.
screen and on the front panel display.
, The self-diagnosis function was activated.
Thedisctraydoesnot openand“LOCKED”
appears on the front panel display.
92
Download from Www.Somanuals.com. All Manuals Search And Download.
The disc tray does not open and “TRAY
LOCKED” appears on the front panel
display.
Self-diagnosis Function
(When letters/numbers appear in the
display)
, Contact your Sony dealer or local
authorized Sony service facility.
“Data error” appears on the TV screen
When the self-diagnosis function is activated
to prevent the player from malfunctioning, a
five-character service number (e.g., C 13 50)
with a combination of a letter and four digits
appears on the screen and the front panel
display. In this case, check the following
table.
when playing a DATA CD or DATA DVD
, The MP3 audio track/JPEG image file/
DivX video file you want to play is broken.
, The data is not MPEG1 Audio Layer 3 data.
, The JPEG image file format does not
conform to DCF (page 62).
, The JPEG image file has the extension
“.JPG” or “.JPEG,” but is not in JPEG
format.
C:13:50
, The file you want to play has the extension
“.AVI” or “.DIVX” but is not in DivX
format, or is in DivX format but does not
conform to a DivX certified profile.
First three
Cause and/or corrective
characters of action
the service
number
C 13
The disc is dirty or recorded
in a format that this player
,Clean the disc with a soft
cloth or check its format
(page 8).
C 31
E XX
The disc is not inserted
correctly.
,Re-insert the disc
correctly.
To prevent a malfunction, the
(xx is a number) player has performed the
self-diagnosis function.
,Contact your nearest
Sony dealer or local
authorized Sony service
facility and give the 5-
character service number.
Example: E 61 10
93
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
Digital audio compression technology that
Digital Theater Systems, Inc. developed. This
technology conforms to multi-channel
surround sound. The rear channel is stereo
and there is a discrete subwoofer channel in
this format. DTS provides the same discrete
channels of high quality digital audio.
Good channel separation is realized because
all of the channel data is recorded discretely
and little deterioration is realized because all
channel data processing is digital.
A unit in which to store JPEG image files or
MP3 audio tracks on a DATA CD. (“Album”
is an exclusive definition for this player.)
Sections of a picture or a music feature that
are smaller than titles. A title is composed of
several chapters. Depending on the disc, no
chapters may be recorded.
A disc that contains up to 8 hours of moving
pictures even though its diameter is the same
as a CD.
The data capacity of a single-layer and single-
sided DVD is 4.7 GB (Giga Byte), which is 7
times that of a CD. The data capacity of a
double-layer and single-sided DVD is 8.5
GB, a single-layer and double-sided DVD is
9.4 GB, and double-layer and double-sided
DVD is 17 GB.
The picture data uses the MPEG 2 format, a
worldwide standard of digital compression
technology. The picture data is compressed to
about 1/40 (average) of its original size. The
DVD also uses a variable rate coding
technology that changes the data to be
allocated according to the status of the
picture. Audio information is recorded in a
multi-channel format, such as Dolby Digital,
allowing you to enjoy a more realistic audio
presence.
®
Digital video technology created by
DivXNetworks, Inc. Videos encoded with
DivX technology are among the highest
quality with a relatively small file size.
Digital audio compression technology
developed by Dolby Laboratories. This
technology conforms to multi-channel
surround sound. The rear channel is stereo
and there is a discrete subwoofer channel in
this format. Dolby Digital provides the same
discrete channels of high quality digital audio
found in “Dolby Digital” theatre surround
sound systems. Good channel separation is
realized because all of the channel data is
recorded discretely and little deterioration is
realized because all channel data processing
is digital.
Furthermore, various advanced functions
such as the multi-angle, multilingual, and
Parental Control functions are provided with
the DVD.
Audio signal processing technology that
Dolby Laboratories developed for surround
sound. When the input signal contains a
surround component, the Pro Logic process
outputs the front, centre and rear signals. The
rear channel is monaural.
A DVD-RW is a recordable and rewritable
disc that is the same size as a DVD VIDEO.
The DVD-RW has two different modes: VR
mode and Video mode. DVD-RWs created in
Video mode have the same format as a DVD
VIDEO, while discs created in VR (Video
Recording) mode allow the contents to be
programmed or edited.
94
Download from Www.Somanuals.com. All Manuals Search And Download.
A DVD+RW (plus RW) is a recordable and
rewritable disc. DVD+RWs use a recording
format that is comparable to the DVD VIDEO
format.
Compared to the Interlace format that
alternately shows every other line of an image
(field) to create one frame, the Progressive
format shows the entire image at once as a
single frame. This means that while the
Interlace format can show 25 or 30 frames
(50-60 fields) in one second, the Progressive
format can show 50-60 frames in one second.
The overall picture quality increases and still
images, text, and horizontal lines appear
sharper. This player is compatible with the
525 or 625 progressive format.
A JPEG image recorded on a DATA CD or a
DivX video on a DATA CD/DATA DVD
(“File” is an exclusive definition for this
player.) A single file consist of a single image
or movie.
Film based software, Video based
software (page 19)
Progressive JPEG
Progressive JPEGs are used mostly on the
internet. They are different from other JPEGs
in that they “fade in” gradually instead of
being drawn from top to bottom when
displayed on a browser. This lets you view the
image while it is being downloaded.
DVDs can be classified as Film based or
Video based software. Film based DVDs
contain the same images (24 frames per
second) that are shown at movie theatres.
Video based DVDs, such as television
dramas or sit-coms, displays images at 30
frames/60 fields (24 frames/50 fields) per
second.
On a VIDEO CD with PBC (playback
control) functions, the menu screens, moving
pictures and still pictures are divided into
sections called “scenes.”
International standard coding system used to
compress audio digital signals authorized by
ISO/IEC. MPEG 1 conforms to up to 2-
channel stereo. MPEG 2, used on DVDs,
conforms to up to 7.1-channel surround.
A Super Audio CD disc can reproduce sounds
that are extremely faithful to the original
sound by use of DSD (Direct Stream Digital)
technology. This technology utilizes a
sampling frequency of 2.8224 MHz, which is
64 times that of a conventional CD, and 1-bit
quantization that enables the disc to hold 4
times the amount of information that a
standard PCM format CD can hold. Super
Audio CDs are divided into the following
types.
Normal (Interlace) format shows every other
line of an image as a single “field” and is the
standard method for displaying images on
television. The even number field shows the
even numbered lines of an image, and the odd
numbered field shows the odd numbered lines
of an image.
• Super Audio CD (single layer disc)
This disc consists of a single HD layer*.
*High density signal layer for the Super Audio CD
HD (high density) layer
• Super Audio CD (dual layer disc)
This disc consists of dual HD layers and is
capable of extended play over long periods.
,continued
95
Download from Www.Somanuals.com. All Manuals Search And Download.
Also, as the dual layer disc consists of dual
HD layers on one side only, you do not have
to turn the disc over during playback.
HD layer
HD layer
• Super Audio CD + CD (Hybrid disc)
This disc consists of an HD layer and a CD
layer. Also, as the dual layers are on one
side only, you do not have to turn the disc
over during playback. You can play the CD
layer using a conventional CD player.
CD layer
HD layer
• 2 channel + Multi-channel Super Audio CD
This disc consists of the 2 channel playback
area and the multi-channel playback area.
2 channel playback
area
Multi-channel
playback area
The longest section of a picture or music
feature on a DVD, movie, etc., in video
software, or the entire album in audio
software.
Sections of a picture or a music feature on a
VIDEO CD, CD or DATA CD (the length of
a song). (“Track” in DATA CD is an
exclusive definition for this player.)
A number that divides a track into sections to
easily locate the point you want on a VIDEO
CD. Depending on the disc, no index may be
recorded.
96
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
System
General
Laser: Semiconductor laser
Signal format system: PAL/(NTSC)
Power requirements:
220 – 240 V AC, 50/60 Hz
Power consumption:
Audio characteristics
DVP-NS955V: 14 W
Frequency response: DVD VIDEO (PCM
96 kHz): 2 Hz to 44 kHz (44 kHz: –2 dB
±1 dB)/Super Audio CD: 2 Hz to 100
kHz (50 kHz: –3 dB ±1 dB)/CD: 2 Hz to
20 kHz (±0.5 dB)
Signal-to-noise ratio (S/N ratio): 115 dB
(LINE OUT L/R (AUDIO) jacks only)
Harmonic distortion: 0.003 %
Dynamic range: DVD VIDEO/Super Audio
CD: 103 dB/CD: 99 dB
DVP-LS785V: 13 W
Dimensions (approx.):
DVP-NS955V: 430 × 55.5 × 237 mm
DVP-LS785V: 430 × 55.5 × 245 mm
(width/height/depth) incl. projecting
parts
Mass (approx.):
DVP-NS955V: 2.3 kg
DVP-LS785V: 2.1 kg
Operating temperature: 5 °C to 35 °C
Operating humidity: 25 % to 80 %
Wow and flutter: Less than detected value
(±0.001% W PEAK)
Supplied accessories
Outputs
(Jack name: Jack type/Output level/Load
impedance)
LINE OUT (AUDIO): Phono jack/2 Vrms/
10 kilohms
Specifications and design are subject to
change without notice.
5.1CH OUTPUT: Phono jack/2 Vrms/
10 kilohms
DIGITAL OUT (OPTICAL): Optical
output jack/–18 dBm (wave length
660 nm)
DIGITAL OUT (COAXIAL): Phono jack/
0.5 Vp-p/75 ohms
LINE OUT (VIDEO): Phono jack/1.0 Vp-p/
75 ohms
S VIDEO OUT: 4-pin mini DIN/Y:
1.0 Vp-p, C: 0.3 Vp-p (PAL), 0.286 Vp-p
(NTSC)/75 ohms
COMPONENT VIDEO OUT (Y, PB/CB,
PR/CR): Phono jack/Y: 1.0 Vp-p, PB/CB,
PR/ CR: 0.7 Vp-p/75 ohms
97
Download from Www.Somanuals.com. All Manuals Search And Download.
Language Code List
The language spellings conform to the ISO 639: 1988 (E/F) standard.
Code Language
Code Language
Code Language
Code Language
1027 Afar
1183 Irish
1347 Maori
1507 Samoan
1508 Shona
1509 Somali
1511 Albanian
1512 Serbian
1513 Siswati
1514 Sesotho
1515 Sundanese
1516 Swedish
1517 Swahili
1521 Tamil
1028 Abkhazian
1032 Afrikaans
1039 Amharic
1044 Arabic
1045 Assamese
1051 Aymara
1052 Azerbaijani
1053 Bashkir
1057 Byelorussian
1059 Bulgarian
1060 Bihari
1061 Bislama
1066 Bengali;
Bangla
1067 Tibetan
1070 Breton
1079 Catalan
1093 Corsican
1097 Czech
1103 Welsh
1105 Danish
1109 German
1130 Bhutani
1142 Greek
1144 English
1145 Esperanto
1149 Spanish
1150 Estonian
1151 Basque
1157 Persian
1165 Finnish
1166 Fiji
1186 Scots Gaelic
1194 Galician
1196 Guarani
1203 Gujarati
1209 Hausa
1349 Macedonian
1350 Malayalam
1352 Mongolian
1353 Moldavian
1356 Marathi
1357 Malay
1358 Maltese
1363 Burmese
1365 Nauru
1217 Hindi
1226 Croatian
1229 Hungarian
1233 Armenian
1235 Interlingua
1239 Interlingue
1245 Inupiak
1248 Indonesian
1253 Icelandic
1254 Italian
1257 Hebrew
1261 Japanese
1269 Yiddish
1283 Javanese
1287 Georgian
1297 Kazakh
1298 Greenlandic
1299 Cambodian
1300 Kannada
1301 Korean
1305 Kashmiri
1307 Kurdish
1311 Kirghiz
1369 Nepali
1376 Dutch
1525 Telugu
1527 Tajik
1528 Thai
1379 Norwegian
1393 Occitan
1403 (Afan)Oromo
1408 Oriya
1417 Punjabi
1428 Polish
1435 Pashto;
Pushto
1436 Portuguese
1463 Quechua
1481 Rhaeto-
Romance
1482 Kirundi
1483 Romanian
1489 Russian
1491 Kinyarwanda
1495 Sanskrit
1498 Sindhi
1501 Sangho
1502 Serbo-
Croatian
1529 Tigrinya
1531 Turkmen
1532 Tagalog
1534 Setswana
1535 Tonga
1538 Turkish
1539 Tsonga
1540 Tatar
1543 Twi
1557 Ukrainian
1564 Urdu
1572 Uzbek
1581 Vietnamese
1587 Volapük
1613 Wolof
1632 Xhosa
1665 Yoruba
1684 Chinese
1697 Zulu
1313 Latin
1326 Lingala
1327 Laothian
1332 Lithuanian
1334 Latvian;
Lettish
1171 Faroese
1174 French
1181 Frisian
1503 Singhalese
1505 Slovak
1506 Slovenian
1345 Malagasy
1703 Not specified
98
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Display
Control Menu Display 13
Numerics
16:9 82
Front panel display 10
DISTANCE 88
4:3 LETTER BOX 82
4:3 PAN SCAN 82
48kHz/96kHz PCM 86
N
Normal (Interlace) format 95
O
On-screen display
Control Menu Display 13
ORIGINAL 36
OSD 81
DOWNMIX
DVD’s menu
A
A-B REPEAT 42
ALBUM 46
ANGLE 57
AUDIO DRC 85
AUDIO FILTER 85
AUDIO SETUP 85
AV ALIGNMENT 61
P
E
PARENTAL CONTROL 73
PAUSE MODE 84
PBC Playback 38
EFFECT 68
F
PICTURE MODE 58
Fast forward 44
Fast reverse 44
FILE 46
PLAY LIST 36
File 95
B
PROGRAM 39
Film based software 95
Front panel display 10
BACKGROUND 82
Batteries 16
C
H
Handling discs
Hooking up 16
CHAPTER 46
Chapter 94
Checking the audio signal
format 53
Connecting 17
Continuous play
CD/VIDEOCD/Super Audio
CD 32
DVD 32
Control Menu 13
CUSTOM 80
CUSTOM PARENTAL
CONTROL 73
CUSTOM PICTURE MODE
I
Q
INDEX 46
Index 96
QUICK 81
Instant Advance 33
Instant Replay 33
Interlace format 95
INTERVAL 68
R
REPEAT 41
Repeat Play 41
RESET 81
Resume 33
J
JPEG 62
L
S
LANGUAGE SETUP 81
LEVEL 88
Scan 44
SCENE 46
Scene 95
LINE 82
Locating
CUSTOM SETUP 83
SCREEN SAVER 82
SCREEN SETUP 82
SEARCH MODE 46
Searching 44
SETUP 80
SHARPNESS 60
SHUFFLE 40
Shuffle Play 40
SIZE 87
a specific point by watching
the TV screen 44
D
DATE 66
M
MEMORY 59
MENU 81
DCS (Digital Cinema Sound)
DIGITAL OUT 85
DIMMER 84
DISPLAY 83
MODE (MP3, JPEG) 67
MULTI/2CH 37
Slow-motion Play 45
,continued
99
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Printed on 100% recycled paper using
VOC (Volatile Organic Compound)-free
vegetable oil based ink.
Sony Corporation Printed in Malaysia
Download from Www.Somanuals.com. All Manuals Search And Download.
|