4-194-402-13(1)
LCD Monitor
Operating Instructions
Before operating the unit, please read this manual thoroughly
and retain it for future reference.
LMD-2110W
© 2010 Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Attention-when the product is installed in Rack:
communications. Operation of this equipment in a
residential area is likely to cause harmful interference in
which case the user will be required to correct the
interference at his own expense.
1. Prevention against overloading of branch
circuit
When this product is installed in a rack and is
supplied power from an outlet on the rack, please
make sure that the rack does not overload the supply
circuit.
You are cautioned that any changes or modifications not
expressly approved in this manual could void your
authority to operate this equipment.
2. Providing protective earth
All interface cables used to connect peripherals must be
shielded in order to comply with the limits for a digital
device pursuant to Subpart B of Part 15 of FCC Rules.
When this product is installed in a rack and is
supplied power from an outlet on the rack, please
confirm that the outlet is provided with a suitable
protective earth connection.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired
operation.
3. Internal air ambient temperature of the rack
When this product is installed in a rack, please make
sure that the internal air ambient temperature of the
rack is within the specified limit of this product.
4. Prevention against achieving hazardous
condition due to uneven mechanical loading
When this product is installed in a rack, please make
sure that the rack does not achieve hazardous
condition due to uneven mechanical loading.
WARNING
Using this unit at a voltage other than 120 V may require
the use of a different line cord or attachment plug, or
both. To reduce the risk of fire or electric shock, refer
servicing to qualified service personnel.
5. Install the equipment while taking the
operating temperature of the equipment into
consideration
For the customers in Canada
This Class A digital apparatus complies with Canadian
ICES-003.
For the operating temperature of the equipment, refer
to the specifications of the Operation Manual.
For the customers in Europe
6. When performing the installation, keep the
following space away from walls in order to
obtain proper exhaust and radiation of heat.
This product with the CE marking complies with the
EMC Directive issued by the Commission of the
European Community.
Compliance with this directive implies conformity to the
following European standards:
Lower, Upper: 4.4 cm (1 3/4 inches) or more
• EN55103-1 : Electromagnetic Interference
(Emission)
• EN55103-2 : Electromagnetic Susceptibility
(Immunity)
For kundene i Norge
Dette utstyret kan kobles til et IT-strømfordelingssystem.
Apparatet må tilkoples jordet stikkontakt
This product is intended for use in the following
Electromagnetic Environments: E1 (residential), E2
(commercial and light industrial), E3 (urban outdoors),
E4 (controlled EMC environment, ex. TV studio).
Suomessa asuville asiakkaille
Laite on liitettävä suojamaadoituskoskettimilla
varustettuun pistorasiaan
För kunderna i Sverige
Apparaten skall anslutas till jordat uttag
For the customers in Europe
The manufacturer of this product is Sony Corporation,
1-7-1 Konan, Minato-ku, Tokyo, Japan.
The Authorized Representative for EMC and product
safety is Sony Deutschland GmbH, Hedelfinger Strasse
61, 70327 Stuttgart, Germany. For any service or
guarantee matters please refer to the addresses given in
separate service or guarantee documents.
For the customers in the U.S.A.
This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference when the equipment is operated in a
commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction
manual, may cause harmful interference to radio
3
Download from Www.Somanuals.com. All Manuals Search And Download.
For the customers in the USA
Lamp in this product contains mercury. Disposal of
these materials may be regulated due to environmental
considerations. For disposal or recycling information,
please contact your local authorities or the
Telecommunications Industry Association
(www.eiae.org).
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
5
Table of Contents
Download from Www.Somanuals.com. All Manuals Search And Download.
• If the unit is used in a cold place, horizontal lines or a
residual image may appear on the screen. This is not
a malfunction. When the monitor becomes warm, the
screen returns to normal.
Precaution
• The screen and the cabinet become warm during
operation. This is not a malfunction.
On Safety
• Operate the unit only with a power source as specified
in the “Specifications” section.
• A nameplate indicating operating voltage, etc., is
located on the rear panel.
• Should any solid object or liquid fall into the cabinet,
unplug the unit and have it checked by qualified
personnel before operating it any further.
• Do not drop or place heavy objects on the power cord.
If the power cord is damaged, turn off the power
immediately. It is dangerous to use the unit with a
damaged power cord.
On Burn-in
For LCD panel, permanent burn-in may occur if still
images are displayed in the same position on the screen
continuously, or repeatedly over extended periods.
Images that may cause burn-in
• Masked images with aspect ratios other than 16:9
• Color bars or images that remain static for a long time
• Character or message displays that indicate settings or
the operating state
• Unplug the unit from the wall outlet if it is not to be
used for several days or more.
• Disconnect the power cord from the AC outlet by
grasping the plug, not by pulling the cord.
• The socket-outlet shall be installed near the equipment
and shall be easily accessible.
To reduce the risk of burn-in
• Turn off the character displays
Press the MENU button to turn off the character
displays. To turn off the character displays of the
connected equipment, operate the connected
equipment accordingly. For details, refer to the
operation manual of the connected equipment.
• Turn off the power when not in use
On Installation
Turn off the power if the viewfinder is not to be used
for a prolonged period of time.
• Allow adequate air circulation to prevent internal heat
build-up.
Do not place the unit on surfaces (rugs, blankets, etc.)
or near materials (curtains, draperies) that may block
the ventilation holes.
• Do not install the unit in a location near heat sources
such as radiators or air ducts, or in a place subject to
direct sunlight, excessive dust, mechanical vibration
or shock.
On a Long Period of Use
Due to the characteristics of LCD panel, displaying
static images for extended periods, or using the unit
repeatedly in a high temperature/high humidity
environments may cause image smearing, burn-in, areas
of which brightness is permanently changed, lines, or a
decrease in overall brightness.
Handling the LCD Screen
In particular, continued display of an image smaller than
the monitor screen, such as in a different aspect ratio,
may shorten the life of the unit.
Avoid displaying a still image for an extended period, or
using the unit repeatedly in a high temperature/high
humidity environment such an airtight room, or around
the outlet of an air conditioner.
• The LCD panel fitted to this unit is manufactured with
high precision technology, giving a functioning pixel
ratio of at least 99.99%. Thus a very small proportion
of pixels may be “stuck”, either always off (black),
always on (red, green, or blue), or flashing. In
addition, over a long period of use, because of the
physical characteristics of the liquid crystal display,
such “stuck” pixels may appear spontaneously. These
problems are not a malfunction.
To prevent any of the above issues, we recommend
reducing brightness slightly, and to turn off the power
whenever the unit is not in use.
• Do not leave the LCD screen facing the sun as it can
damage the LCD screen. Take care when you place
the unit by a window.
• Do not push or scratch the LCD screen. Do not place
a heavy object on the LCD screen. This may cause the
screen to lose uniformity.
6
Precaution
Download from Www.Somanuals.com. All Manuals Search And Download.
On Cleaning
On Mounting on a Rack
Leave 1U space empty above and below the monitor to
ensure adequate air circulation or install a fan to
maintain the monitor’s performance.
Before cleaning
Be sure to disconnect the AC power cord from the AC
outlet.
On cleaning the monitor screen
The monitor screen surface is especially treated to
reduce reflection of light.
If you have any questions about this unit, contact your
authorized Sony dealer.
As incorrect maintenance may impair the performance
of the monitor, take care with respect to the following:
• Wipe the screen gently with a soft cloth such as a
cleaning cloth or glass cleaning cloth.
• Stubborn stains may be removed with a soft cloth such
as a cleaning cloth or glass cleaning cloth lightly
dampened with water.
On Fan Error
The fan for cooling the unit is built in. When the fan
stops and the KEY INHIBIT indicator on the front panel
blinks for fan error indication, turn off the power and
contact an authorized Sony dealer.
• Never use solvent such as alcohol, benzene or thinner,
or acid, alkaline or abrasive detergent, or chemical
cleaning cloth, as they will damage the screen surface.
On cleaning the cabinet
• Clean the cabinet gently with a soft dry cloth.
Stubborn stains may be removed with a cloth lightly
dampened with mild detergent solution, followed by
wiping with a soft dry cloth.
• Use of alcohol, benzene, thinner or insecticide may
damage the finish of the cabinet or remove the
indications on the cabinet. Do not use these chemicals.
• If you rub on the cabinet with a stained cloth, the
cabinet may be scratched.
• If the cabinet is in contact with a rubber or vinyl resin
product for a long period of time, the finish of the
cabinet may deteriorate or the coating may come off.
On Moisture Condensation
If the unit is brought directly from a cold place to a warm
place, or the unit is warm and the ambient temperature
cools suddenly (by air-conditioning, for example),
moisture may condense on the surface or inside of the
unit, or create a mist residue inside the protection plate
if it is installed to the unit.
This is called moisture condensation, and is not a
malfunction of the product itself, although it may cause
damage to the unit.
Leave the unit in a condensation free area.
If moisture condensation has occurred, turn off the unit
and do not use it until moisture condensation has
evaporated.
On Repacking
Do not throw away the carton and packing materials.
They make an ideal container which to transport the
unit.
7
Precaution
Download from Www.Somanuals.com. All Manuals Search And Download.
For more information, see “Installing to the Rack”
Features
Consult with Sony qualified personnel for wall mount
installation.
The LMD-2110W (21.5-type) is a multiple format LCD
monitor for broadcast/professional use featuring a
precise image and high performance. Supporting digital/
analog main broadcast signals, and HDMI input, it can
be used under various lighting conditions.
3-color tally lamp
The tally lamp lights in red, green or amber to monitor
each input picture and check the on-air mode.
1)
Blue only mode
1)
HDMI, the HDMI logo and High-Definition Multimedia Interface are
In the blue only mode, a monochrome display is
obtained with all three of the R/G/B picture elements
driven with a blue signal. This mode is convenient for
chroma and phase adjustments and monitoring of signal
noise.
trademarks or registered trademarks of HDMI Licensing LLC.
High brightness LCD panel
Because of precise image and high speed response, real
color image can be reproduced.
Multi-format
Marker function
The monitor supports the video, Y/C, RGB, component
and HDMI input signals.
Both NTSC and PAL color systems are supported, and
the appropriate color system is selected automatically.
SDI signals can be available when input adaptor BKM-
320D (optional) is used.
SAFETY AREA marker, CENTER MARKER, 16:9
MARKER for the 4:3 aspect ratio or 4:3 MARKER for
the 16:9 aspect ratio can be displayed.
Scan setting
You can set the display size to normal scan, over scan or
full screen mode.
HD/SD-SDI signals can be available when input adaptor
BKM-341HS (optional) is used.
Select color temperature and gamma mode
You can select the color temperature from among two
(HIGH and LOW) settings.
For more information, see “Video signal formats”
You can select the gamma mode from among five
settings.
External sync input
When the EXT SYNC button is in the on position, the
unit can be operated on the sync signal supplied from an
external sync generator.
Aspect setting
You can set the monitor to 4:3 or 16:9 display mode
according to the input video signal.
Automatic termination (connector with
mark only)
On-screen menus
You can set the appropriate settings according to the
connected system by using the on-screen menus.
The input connector is terminated internally at 75 ohms
when nothing has been connected to the output
connector. If a cable is connected to the output
connector, the internal terminal is automatically
released and the signals input to the input connector are
output to the output connector (loop-through).
Select language display
You can select from seven display languages, English,
French, German, Spanish, Italian, Japanese and
Chinese.
External remote control function
You can directly select the input signal, aspect, etc., by
operating the equipment connected to the PARALLEL
REMOTE connector.
Key inhibit function
You can inhibit a key function to prevent missing an
operation.
Monitor stand with tilt function
A monitor stand with tilt function is equipped for desk
top use. It shall be removed when mounted on the rack.
I/P mode setting
This unit is equipped with an I/P mode setting function
that is used to minimize picture delay due to the signal
conversion process.
Rack mount
The monitor supports the VESA (100 × 100 mm)
standard.
It can be mounted on an EIA standard 19-inch rack
(using an optional mounting bracket).
8
Features
Download from Www.Somanuals.com. All Manuals Search And Download.
Location and Function of Parts and Controls
Front Panel
1
MENU
VOLUME
RGB/
EXT
SYNC
BLUE
ONLY
1
LINE
HDMI COMPONENT
SDI
SCAN ASPECT
KEY
INHIBIT
RESET
ENTER
qd qs qa 0 9 8 7 6
5
4 3 2
qf
a Tally lamp
You can check the status of the monitor by the color of
ENTER button
Press to confirm a selected item on the menu.
the tally lamp.
The tally lamp lights in red, green or amber according to
the setting of the REMOTE menu.
f ASPECT select button
Sets the aspect ratio of the picture, 4:3 or 16:9.
g SCAN select button
b 1 (standby) switch and indicator
You can change the scan size of the picture.
Press to change the scan size among over (5% over
scan), normal (0% scan) and full screen set on the SCAN
Press to turn on the power when this unit is in standby
mode. The indicator turns on. Press again to set the
monitor in standby mode. The indicator goes out.
c KEY INHIBIT indicator
Lights when the key inhibit function works.
h BLUE ONLY button
Press to eliminate the red and green signals. Only blue
signal is displayed as a monochrome picture on the
screen. This mode is convenient for chroma and phase
adjustments and monitoring of signal noise.
The indicator blinks when fan error occurs.
For details on the key inhibit, see “KEY INHIBIT menu”
d VOLUME buttons
Press the + button to increase the volume or the – button
to decrease it.
i EXT SYNC (external sync) button
Press to operate the unit on an external sync signal
through the EXT SYNC IN connector.
The EXT SYNC button works when the component/
RGB signals are input.
e Menu operation buttons
Displays or sets the on-screen menu.
j SDI button
Press to monitor the signal through the OPTION IN
connector.
M/m/</, (arrow) buttons
Select the menu or make various adjustments.
MENU button
Press to display the on-screen menu.
Press again to clear the menu.
k RGB/COMPONENT button
Press to monitor the signal through the RGB/
COMPONENT input connector.
RESET button
l HDMI button
Press to monitor the signal through the HDMI IN
connector.
Resets the value of an item back to the previous value.
This button functions when the menu item is adjusted
(displayed) on the screen.
9
Location and Function of Parts and Controls
Download from Www.Somanuals.com. All Manuals Search And Download.
m LINE button
Press to monitor the signal through the LINE input
connector.
n Speaker
The audio signal selected by the input select button (j
SDI button, k RGB/COMPONENT button, l HDMI
button or m LINE button) on the front panel is output.
Input Signals and Adjustable/Setting Items
Input signal
RGB
Item
Video,
Y/C
Component
SDI*4
SD/HD
a
HDMI
HD
a
B & W
SD
a
HD
SD
a
HD
a
SD
a
DVI*5
a
CONTRAST
BRIGHT
a
a
a
a
a
×
a
a
a
a
a
a
a
a
a
a
CHROMA
a
a
a
a
×
×
×
×
×
×
PHASE
a
(NTSC)
×
×
×
×
×
×
APERTURE
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
×
a
COLOR TEMP
COMPONENT LEVEL*1
a
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
(480/60I)
NTSC SETUP
a
a
×
(NTSC) (480/60I)
GAMMA
SCAN
a
a
a
a
a
a
×
a
a
a
a
×
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
×
a
a
a
a
a
a
×
a
a
a
×
×
×
×
×
×
a*2
a
a*2
a
a*2
a
ASPECT
MARKER
BLUE ONLY
I/P MODE*3
EXT SYNC
a
a
a
a
a
a
a
×
a
a
×
SD PIXEL MAPPING
COMPOSITE&Y/C
a
a
×
×
×
×
×
×
×
×
×
×
×
×
×
×
SD PIXEL MAPPING
RGB/COMPONENT
×
×
a
a
a : Adjustable/can be set
× : Not adjustable/cannot be set
*1 When a component signal (480/60I) is input, this can be
switchable.
*2 When a 480/60P or 576/50P signal is input, this can be
switchable.
*3 When an interlace signal is input, this can be switchable.
*4 When BKM-320D or BKM-341HS is used, SDI signals can
be input.
*5 When a PC signal is input to the HDMI IN connector using a
DVI conversion cable, this can be adjusted.
10
Location and Function of Parts and Controls
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Panel
9
8
7 6 5 4 3 2
1
IN
LINE
OUT
PARALLEL REMOTE
RGB/COMPONENT
OPTION
AUDIO IN
IN
OUT
IN
G/Y
B/PB
R/PR
OPTION IN
IN
IN
OUT
IN
OUT
IN
IN
EXT
OUT
OUT
VIDEO
SYNC
OUT
IN
OUT
AUDIO
AUDIO
a HDMI IN connector
HDMI (High-Definition Multimedia Interface) is an
e EXT SYNC IN/OUT (external sync) connectors
(BNC)
interface that supports both video and audio on a single
digital connection, allowing you to enjoy high quality
digital picture and sound. The HDMI specification
supports HDCP (High-bandwidth Digital Content
Protection), a copy protection technology that
Press the EXT SYNC button to use the sync signal
through this connector.
IN connector
When this unit operates on an external sync signal,
connect the reference signal from a sync generator
to this connector.
incorporates coding technology for digital video signals.
Notes
Note
• Use HDMI compliant cable (optional) with HDMI
logo.
When inputting a video signal with the jitters, etc.
the picture may be disturbed. We recommend using
the TBC (time base corrector).
• Color noise may appear on the edge of the screen
depending on the connected device. This is not a
malfunction.
OUT connector
b HDMI cable holder
Secures the HDMI cable (Ø7 mm or less).
Loop-through output of the IN connector. Connect
to the external sync input of video equipment to be
synchronized with this unit.
Close
When the cable is connected to this connector, the
75-ohms termination of the input is automatically
released, and the signal input to the IN connector is
output from this connector.
Cable
f RGB/COMPONENT connectors
Analog RGB signal or component (Y/PB/PR) signal
input connectors and their loop-through output
connectors.
Press the RGB/COMPONENT button to monitor the
signal input through these connectors.
c OPTION IN connector (D-sub 9-pin, female)
Inputs SD-SDI signals when optional Sony BKM-320D
is connected. Inputs HD/SD-SDI signals when optional
Sony BKM-341HS is connected.
Press the SDI button to select the signal.
G/Y, B/PB, R/PR IN/OUT (BNC)
Note
These are the input/output connectors for an analog
RGB and a component (Y/PB/PR) signal. Unless an
external sync signal is input, the monitor is
synchronized with the sync signal contained in the
G/Y signal.
Do not connect the equipment other than BKM-320D or
BKM-341HS. It causes damage to the unit or the
equipment.
d OPTION AUDIO IN connector (phono jack)
Inputs an audio signal if the BKM-320D or BKM-
341HS is connected to the OPTION IN connector.
Press the SDI button to monitor the audio signal.
AUDIO IN/OUT (phono jack)
When using an analog RGB or a component signal
as a video signal, use these jacks for the input/
output of an audio signal. Connect them to the
11
Location and Function of Parts and Controls
Download from Www.Somanuals.com. All Manuals Search And Download.
audio input/output jacks on equipment such as a
VCR.
Installing to the Rack
g PARALLEL REMOTE connector (modular
connector, 8-pin)
Forms a parallel switch and controls the monitor
1
Remove the screws (4) to remove the stand.
externally.
For details on the pin assignment and factory setting
function assigned to each pin, see page 24.
CAUTION
For safety, do not connect the connector for peripheral
device wiring that might have excessive voltage to this
port. Follow the instructions for this port.
h LINE connectors
Line input connectors for Y/C separate, composite video
and audio signals and their loop-through output
connectors.
Press the LINE button to monitor the signal input
through these connectors.
If you input signals to both Y/C IN and VIDEO IN, the
signal input to the Y/C IN is selected.
2
Attach the unit to the rack using the mounting
bracket.
Y/C IN/OUT (4-pin mini-DIN)
These are the input/output connectors for a Y/C
separate signal. Connect them to the Y/C separate
input/output connectors on equipment such as a
VCR, video camera, or another monitor.
VIDEO IN/OUT (BNC)
These are the input/output connectors for a
composite video signal. Connect them to the
composite video input/output connectors on
equipment such as a VCR, video camera, or another
monitor.
AUDIO IN/OUT (phono jack)
These are the input/output jacks for an audio signal.
Connect them to the audio input/output jacks on
equipment such as a VCR.
LI
N
E
H
D
M
I
R
GB
CO
/
M
PO
NE
NT
S
D
I
E
X
T
S
Y
N
B
L
O
C
U
E
Y
N
L
S
C
A
N
A
S
P
E
C
T
M
E
N
U
R
E
S
E
T
VO
LU
M
E
E
N
TE
R
K
E
Y
IT
IN
H
IB
i AC IN socket
Connect the supplied AC power cord.
12
Installing to the Rack
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the AC
Power Cord
Attaching the Input
Adaptor
1
Plug the AC power cord into the AC IN socket on
the rear panel. Then, attach the AC plug holder
(supplied) to the AC power cord.
Before attaching the input adaptor, disconnect the power
cord.
BKM-320D
AC IN socket
Tighten the screws.
L
IN
E
IN
O
U
T
VIDEO
IN
O
U
T
AU
D
IO
BKM-341HS
AC power cord
Tighten the screws.
AC plug holder (Supplied)
2
Slide the AC plug holder over the cord until it
locks.
L
IN
E
Note
IN
O
U
T
VIDEO
Do not connect the equipment other than BKM-320D or
BKM-341HS. It causes damage to the unit or the
equipment.
IN
O
U
T
AU
D
IO
To disconnect the AC power cord
Pull out the AC plug holder while pressing the lock
levers.
13
Connecting the AC Power Cord / Attaching the Input Adaptor
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the Default
Settings
When you turn on the unit for the first time after
purchasing it, select the area where you intend to use this
unit from among the options.
The default setting values for each area
MENU
VOLUME
1
KEY
INHIBIT
RESET
ENTER
3
2~3
1
1
5
1
Press the 1 (standby) switch.
4
The power is turned on and the SELECT SETTING
screen appears.
2
3
3
1North America
COLOR COMPONENT
NTSC
S E L E C T S E T T I N G
N O R T H _ A M E R I C A
L A T I N A M E R I C A
A F R I C A A U S T R A L A S I
A S I A E X C E P T J A P A N
J A P A N
TEMP
LOW
LOW
LOW
LOW
LEVEL
BETA7.5
SMPTE
SMPTE
SMPTE
SETUP
2Latin America
1NORTH AMERICA
7.5
0
3Africa,Australia/New
Zealand, Europe,
Middle East, Russia
ARGENTINA
PARAGUAY
URUGUAY
2LATIN AMERICA
0
PAL&PAL-N
AREA
0
4Asia Except Japan
NTSC&PAL-M
AREA
OTHER AREA
LOW
LOW
BETA7.5
SMPTE
7.5
0
5Japan
3AFRICA AUSTRALASIA
EUROPE MIDDLE-EAST
2
Press the M or m button to select the area where you
intend to use the unit and press the , or ENTER
button.
NTSC AREA
PAL AREA
LOW
LOW
HIGH
BETA7.5
SMPTE
SMPTE
7.5
0
4ASIA EXCEPT
JAPAN
5JAPAN
0
If you select either 1, 3 or 5
The confirmation screen is displayed. Confirm the
selected area. When the setting is wrong, press the
< button to return to the previous screen.
S E L E C T T H I S A R E A ?
N O R T H A M E R I C A
[ E N T E R ] Y E S
[ M E N U ] NO
If you select either 2 or 4
One of the following screens appears. Press the M
or m button to narrow the area further and then
press the , or ENTER button.
The confirmation screen is displayed. Confirm the
selected area. When the setting is wrong, press the
< button to return to the previous screen.
14
Selecting the Default Settings
Download from Www.Somanuals.com. All Manuals Search And Download.
2 If LATIN AMERICA is selected:
Selecting the Menu
Language
PAL&PAL-N area
L A T I N A M E R I C A
P A L & P A L - N _ A R E A
Argentina
A R G E N T I N A
P A R A G U A Y
U R U G U A Y
Paraguay
You can select one of seven languages (English, French,
German, Spanish, Italian, Japanese, Chinese) for
displaying the menu and other on-screen displays.
“ENGLISH (English)” is selected in the default setting.
The current settings are displayed in place of the x
marks on the illustrations of the menu screen.
N T S C & P A L - M A R E A
O T H E R A R E A
Uruguay
NTSC&PAL-M area
Other area
4 If ASIA EXCEPT JAPAN is selected:
Customers who will use this unit in the shaded
areas shown in the map below should select NTSC
AREA.
Other customers should select PAL AREA.
MENU
VOLUME
1
KEY
INHIBIT
RESET
ENTER
3~5
2
1
1
2
Press the 1 (standby) switch to turn on the unit.
Press the MENU button.
A S I A E X C E P T J A P A N
N T S C _ A R E A
The menu appears.
The menu presently selected is shown in yellow.
NTSC area
PAL area
P A L A R E A
USER CONTROL
CONTROL
CONTRAST:
BRIGHTNESS:
CHROMA:
PHASE:
APERTURE:
BACKLIGHT:
xx
xx
xx
xx
x
3
Press the M or m button to narrow the area further
and then press the , or ENTER button.
x
The SELECT SETTING screen disappears and the
menu item settings suitable for the selected area are
applied.
Note
3
Press the M or m button to select SYSTEM
SETTING of the USER CONFIG (User
Configuration) menu, then press the , or ENTER
button.
When you have selected the wrong area, set the
following items using the menu.
on the setting value.
15
Selecting the Menu Language
Download from Www.Somanuals.com. All Manuals Search And Download.
The setting items (icons) in the selected menu are
displayed in yellow.
Using the Menu
USER CONFIG – SYSTEM SETTING 1/2
RGB/COMP SEL:
COMPONENT LEVEL:
NTSC SETUP:
SCAN:
GAMMA:
FORMAT DISPLAY:
LANGUAGE:
xxxxxxx
xxxxxxx
xxxxxxx
xxxxxxx
xxxxxxx
xxxxxxx
xxENGLISH
xxxxxxx
xxxxxxx
The unit is equipped with an on-screen menu for making
various adjustments and settings such as picture control,
input setting, set setting change, etc. You can also
change the menu language displayed in the on-screen
menu.
BACKGROUND:
I/P MODE:
To change the menu language, see “Selecting the Menu
The current settings are displayed in place of the x
marks on the illustrations of the menu screen.
4
Press the M or m button to select “LANGUAGE,”
then press the , or ENTER button.
The selected item is displayed in yellow.
USER CONFIG – SYSTEM SETTING 1/2
RGB/COMP SEL:
COMPONENT LEVEL:
NTSC SETUP:
SCAN:
GAMMA:
FORMAT DISPLAY:
LANGUAGE:
xxxxxxx
xxxxxxx
xxxxxxx
xxxxxxx
xxxxxxx
xxxxxxx
xENGLISH
xxxxxxx
xxxxxxx
BACKGROUND:
I/P MODE:
MENU
VOLUME
1
KEY
INHIBIT
RESET
ENTER
5
Press the M or m button to select a language, then
press the , or ENTER button.
2~4
1
The menu changes to the selected language.
1
Press the MENU button.
The menu appears.
USER CONFIG – SYSTEM SETTING 1/2
RGB/COMP SEL:
COMPONENT LEVEL:
NTSC SETUP:
SCAN:
GAMMA:
FORMAT DISPLAY:
LANGUAGE:
xxx
xxxxx
x
xxxxxx
xx
xx
The menu presently selected is shown in yellow.
USER CONTROL
CONTROL
ENGLISH
xx
BACKGROUND:
I/P MODE:
CONTRAST:
BRIGHTNESS:
CHROMA:
PHASE:
APERTURE:
BACKLIGHT:
xx
xx
xx
xx
x
x
x
To clear the menu
Press the MENU button.
The menu disappears automatically if a button is not
pressed for one minute.
2
Press the M or m button to select a menu, then press
the , or ENTER button.
The menu icon presently selected is shown in
yellow and setting items are displayed.
16
Using the Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
USER CONFIG – SYSTEM SETTING 1/2
RGB/COMP SEL:
Adjustment Using the
Menus
xxx
xxxxx
COMPONENT LEVEL:
NTSC SETUP:
SCAN:
x
xxxxxx
xx
GAMMA:
FORMAT DISPLAY:
LANGUAGE:
BACKGROUND:
I/P MODE:
xx
ENGLISH
xx
Items
x
The screen menu of this monitor consists of the
following items.
3
4
Select an item.
STATUS (the items indicate the
current settings.)
Press the M or m button to select the item, then
press the , or ENTER button.
The item to be changed is displayed in yellow.
For the video input
FORMAT
COLOR TEMP
GAMMA
COMPONENT LEVEL
NTSC SETUP
RGB/COMP SEL
SCAN MODE
Note
If the menu consists of multiple pages, press M or
m button to go to the desired menu page.
Make the setting or adjustment on an item.
When changing the adjustment level:
To increase the number, press the M button.
To decrease the number, press the m button.
Press the ENTER button to confirm the number,
then restore the original screen.
When changing the setting:
Press the M or m button to change the setting.
Press the ENTER button to confirm the setting.
Model name and serial number
OPTION
For the DVI input
FORMAT
fH
fV
COLOR TEMP
Model name and serial number
OPTION
Notes
• An item displayed in black cannot be accessed.
You can access the item if it is displayed in white.
• If the key inhibit has been turned on, all items are
displayed in black. To change any of the items,
turn the key inhibit to OFF first.
COLOR TEMP/BAL
COLOR TEMP
MANUAL ADJUSTMENT
For details on the key inhibit, see “KEY INHIBIT
USER CONTROL
CONTROL
To clear the menu
USER CONFIG
Press the MENU button.
The menu disappears automatically if a button is not
pressed for one minute.
SYSTEM SETTING
RGB/COMP SEL
COMPONENT LEVEL
NTSC SETUP
About the memory of the settings
The settings are automatically stored in the monitor
memory.
SCAN
GAMMA
FORMAT DISPLAY
LANGUAGE
BACKGROUND
I/P MODE
SD PIXEL MAPPING
MARKER SETTING
MARKER ENABLE
To reset items that have been adjusted
Pressing the RESET button while you are adjusting any
of the menu items resets the menu item to the previous
setting.
17
Adjustment Using the Menus
Download from Www.Somanuals.com. All Manuals Search And Download.
MARKER SELECT
CENTER MARKER
SAFETY AREA
For the DVI input
STATUS 1/2
FORMAT
MARKER LEVEL
xxx
xxxxxxx
xxxxxxx
xxxxx
fH
fV
REMOTE
COLOR TEMP
xxxx
PARALLEL REMOTE
1PIN
2PIN
3PIN
4PIN
6PIN
7PIN
8PIN
STATUS 2/2
LMD-2110W
xxxxxxx
OPTION
BKM-320D
KEY INHIBIT
KEY INHIBIT
• Signal format
• fH
• fV
Adjusting and Changing the
Settings
• Color temperature
• Model name and serial number
• Option
STATUS menu
The STATUS menu is used to display the current status
of the unit. The following items are displayed:
COLOR TEMP/BAL menu
The COLOR TEMP/BAL menu is used for adjusting the
picture white balance.
For the video input
You need to use the measurement instrument to adjust
the white balance.
STATUS 1/2
FORMAT
xxxxxxxxx
xxxxxxxx
xxx
Recommended: Konica Minolta color analyzer CA-210
COLOR TEMP
GAMMA
COMPONENT LEVEL
NTSC SETUP
RGB/COMP SEL
SCAN MODE
xx
COLOR TEMP/BAL
xxxxx
x
xx
COLOR TEMP:
xxxxxx
xxx
xxxxxxxx
MANUAL ADJUSTMENT
ADJUST GAIN:
ADJUST BIAS:
COPY FROM:
STATUS 2/2
LMD-2110W
OPTION
xxxxxxx
BKM-320D
Submenu
Setting
COLOR TEMP
Selects the color temperature from
among HIGH, LOW and USER
setting.
• Signal format
• Color temperature
• Gamma
• Component level
• NTSC setup
• RGB/Component select
• Scan mode
• Model name and serial number
• Option
18
Adjustment Using the Menus
Download from Www.Somanuals.com. All Manuals Search And Download.
USER CONFIG menu
Submenu
Setting
The USER CONFIG menu is used for setting the system
and marker. You can set the display language and so on.
Items that cannot be adjusted depending on the input
signal are displayed in black.
MANUAL
ADJUSTMENT
If you set the COLOR TEMP to
USER setting, the item displayed is
changed from black to white, which
means you can adjust the color
temperature.
• ADJUST GAIN: Adjusts the
color balance (GAIN).
USER CONFIG
• ADJUST BIAS: Adjusts the
color balance (BIAS).
SYSTEM SETTING:
MARKER SETTING:
• COPY FROM: If you select
HIGH or LOW, the white
balance data for the selected
color temperature will be
copied in the USER setting.
USER CONTROL menu
The USER CONTROL menu is used for adjusting the
picture.
SYSTEM SETTING
Items that cannot be adjusted depending on the input
signal are displayed in black.
USER CONFIG – SYSTEM SETTING 1/2
RGB/COMP SEL:
COMPONENT LEVEL:
NTSC SETUP:
SCAN:
GAMMA:
FORMAT DISPLAY:
LANGUAGE:
xxx
xxxxx
x
xxxxxx
xx
xx
For details of input signal and adjustable / setting items,
USER CONTROL
CONTROL
ENGLISH
xx
BACKGROUND:
I/P MODE:
CONTRAST:
BRIGHTNESS:
CHROMA:
PHASE:
APERTURE:
BACKLIGHT:
xx
xx
xx
xx
x
x
x
USER CONFIG – SYSTEM SETTING 2/2
SD PIXEL MAPPING
COMPOSITE&Y/C:
RGB/COMPONENT:
xxxxxxx
xxxxxxx
Submenu
CONTROL
Setting
You can adjust the picture.
• CONTRAST: Adjusts the
picture contrast.
• BRIGHTNESS: Adjusts the
picture brightness.
• CHROMA: Adjusts color
intensity. The higher the
setting, the greater the
intensity. The lower the
setting, the lower the
Submenu
RGB/COMP SEL
Setting
When a signal input via the RGB/
COMPONENT connector is being
monitored, based on the signal
being input, select RGB or COMP
(component).
intensity.
• PHASE: Adjusts color tones.
The higher the setting, the
more greenish the picture.
The lower the setting, the
more purplish the picture.
• APERTURE: Adjusts the picture
sharpness.
COMPONENT LEVEL Selects the component level from
among three modes.
• SMPTE: for 100/0/100/0 signal
• BETA0: for 100/0/75/0 signal
• BETA7.5: for 100/7.5/75/7.5
signal
The higher the setting, the
sharper the picture. The
lower the setting, the softer
the picture.
NTSC SETUP
Selects the NTSC setup level from
two modes.
The 7.5 setup level is used mainly
in North America. The 0 setup level
is used mainly in Japan.
• BACKLIGHT: Adjusts the
backlight. When the setting
is changed, the brightness of
the backlight is changed.
19
Adjustment Using the Menus
Download from Www.Somanuals.com. All Manuals Search And Download.
Submenu
Setting
Submenu
Setting
SCAN
Sets the scan size of the picture.
Select from OFF and FULL.
The display format changes
depending on the mode selected.
21)
SD PIXEL MAPPING
Selects SD picture size (pixels)
according to input signal format.
• COMPOSITE&Y/C: Set to
monitor the signal input
through the LINE connector
(VIDEO IN or Y/C IN
• OFF: Changes between over scan
connector).
and normal scan.
• FULL: Changes to over scan,
normal scan or full screen.
• RGB/COMPONENT: Set to
monitor the signal input
through the RGB/
COMPONENT connector.
GAMMA
Select the appropriate gamma
mode. You can select from among
five settings. When "3" is selected,
the setting is roughly same as the
gamma mode of the CRT (2.2).
When picture signals in the size
of 720 × 576 (50i) (or 720 × 487
(60i)) are input
Select 720 × 576 (or 720 ×
487). This is the default
setting.
FORMAT DISPLAY
Selects the display mode of the
signal format.
• ON: The format is always
When 702 × 576 (or 712 ×
483) is selected, all sides of
the input picture are cut off
by several pixels.
displayed.
• OFF: The display is hidden.
• AUTO: The format is displayed
for about five seconds when
the input of the signal starts.
When picture signals in the size
of 702 × 576 (50i) (or 712 × 483
(60i)) or equivalent are input
Select 702 × 576 (or 712 ×
483).
LANGUAGE
Selects the menu or message
language from among seven
languages.
• ENGLISH: English
• FRANÇAIS: French
• DEUTSCH: German
• ESPAÑOL: Spanish
• ITALIANO: Italian
When 720 × 576 (or 720 ×
487) is selected, a black
border (of several pixels
wide) appears around the
input picture.
•
•
: Japanese
: Chinese
BACKGROUND
Sets the brightness of the black bars
appearing in the upper and lower
positions of the screen, or on the
sides of the screen.
• OFF: Displays a darker bar
(black).
• ON: Displays a brighter bar
(gray).
I/P MODE (picture delay Select to set the delay by the picture
minimum)
processing to the minimum level
when the signal is input.
• INTER-FIELD: Performs
interpolation depending on
the movement of the images
between the fields. It takes
longer than “LINE
DOUBLER” for processing
the picture. “INTER-
FIELD” is the factory
setting.
• LINE DOUBLER: The
processing time is shorter.
Performs interpolation by
repeating each line in the
data receiving sequence
regardless of the field. As
the line flicker is displayed
in this mode, it is available
for checking the line flicker
of the telop work and so on.
20
Adjustment Using the Menus
Download from Www.Somanuals.com. All Manuals Search And Download.
Scan mode image
Submenu
Setting
CENTER MARKER
Select ON to display the center
mark of the picture and OFF not to
display.
Input
SAFETY AREA
Selects the safe area size for the
aspect ratio determined by the
button which the aspect function is
assigned.
16
4
9
3
You can select from among OFF,
80%, 85%, 88%, 90% and 93%.
When the marker is displayed, the
safe area for the marker is
displayed.
OVER SCAN
(5% OVER
SCAN)
16
4
MARKER LEVEL
Sets the luminance to display the
MARKER SELECT, CENTER
MARKER and SAFETY AREA.
When the setting is low, the marker
is displayed dark.
9
3
NORMAL
SCAN (0%
SCAN)
4
16
REMOTE menu
Select the PARALLEL REMOTE connector pins for
which you want to change the function.
9
3
REMOTE
FULL
PARALLEL REMOTE
4
1PIN:
2PIN:
3PIN:
4PIN:
6PIN:
7PIN:
8PIN:
xxx
xxxx
xxxx
xxxxx
xxxxx
xxxx
xxx
–
3
MARKER SETTING
You can assign various functions to 1 to 4 pins and 6 to
8 pins. The following lists the functions you can assign
to the pins.
USER CONFIG – MARKER SETTING
MARKER ENABLE:
MARKER SELECT:
CENTER MARKER:
SAFETY AREA:
xxx
xxx
xx
xxx
x
REMOTE
• – – – ("– – –": No function is assigned.)
• LINE
MARKER LEVEL:
• HDMI
• RGB/COMP
• 16:9
• 4:3
• NORMAL
• OVER
Submenu
Setting
• FULL
• TALLY R
• TALLY G
MARKER ENABLE
Selects ON to display the marker
and OFF not to display.
MARKER SELECT
When the frame of the film is
displayed on the screen, select the
aspect ratio according to the film.
When 16:9 aspect ratio is selected
with the ASPECT select button
You can select either 4:3 or
OFF.
When 4:3 aspect ratio is selected
with the ASPECT select button
You can select either 16:9 or
OFF.
• EXT SYNC
• BLUE ONLY
• 16:9 MARKER
• 4:3 MARKER
• CENTER MARKER
• SAFE AREA 80%
• SAFE AREA 85%
• SAFE AREA 88%
• SAFE AREA 90%
• SAFE AREA 93%
21
Adjustment Using the Menus
Download from Www.Somanuals.com. All Manuals Search And Download.
• SDI
Troubleshooting
If you use the PARALLEL REMOTE function, you
need to connect cables.
KEY INHIBIT menu
KEY INHIBIT
This section may help you isolate the cause of a problem
and as a result, eliminate the need to contact technical
support.
• The display is colored in green or purple t Select
the correct input from the RGB/COMP SEL setting in
the USER CONFIG menu (page 19).
KEY INHIBIT:
xx
• The unit cannot be operated t The key protection
function works. Set the KEY INHIBIT setting to OFF
in the KEY INHIBIT menu.
You can lock the setting so that they cannot be changed
by an unauthorized user.
Select OFF or ON.
If you set to ON, all items are displayed in black,
indicating the items are locked.
22
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
Y/C output 4-pin mini-DIN (1), Loop-through,
with 75 Ω automatic terminal
function
Specifications
VIDEO output
BNC type (1), Loop-through, with
75 Ω automatic terminal function
AUDIO output
Picture performance
LCD panel
Picture size
a-Si TFT Active Matrix
21.5 type
Phono jack (1), Loop-through
RGB/COMPONENT output connectors
RGB/Component output
477 × 268, 547 mm
(W/H, Diagonal)
7
5
5
(18 /8 × 10 /8, 21 /8 inches)
1920 × 1080 dots
BNC type (3), Loop-through, with
75 Ω automatic terminal function
AUDIO output
Resolution
Viewing angle (LCD panel specifications)
(up/down/left/right, contrast > 10:1)
Phono jack (1), Loop-through
External synchronized output connector
BNC type (1), Loop-through, with
75 Ω automatic terminal function
Built-in speaker output
80°/80°/85°/85° (typical)
Normal 0%
Over 5%
Scan
Aspect
16:9
Display color
16,770,000
0.5 W (mono)
Input/output connectors
General
Power
Power consumption
Maximum: approx. 69 W, 1.3 A to
AC 100 to 240 V, 50/60 Hz
Input
LINE input connectors
Y/C input 4-pin mini-DIN (1)
VIDEO input
0.6 A
Inrush current (1) Maximum possible inrush current
at initial switch-on (Voltage
changes caused by manual
switching):
BNC type (1), 1 Vp-p 3 dB, negative
synchronization
AUDIO input
Phono jack (1), –5 dBu 47 kΩ or higher
RGB/COMPONENT input connectors
60A peak, 0.4A r.m.s. (240V AC)
(2) Inrush current after a mains
interruption of five seconds
(Voltage changes caused at zero-
crossing):
BNC type (3)
RGB input 0.7 Vp-p 3 dB, (Sync On Green,
0.3 Vp-p negative sync.)
Component input
48A peak, 0.3A r.m.s. (240V AC)
Operating conditions
0.7 Vp-p 3 dB, (75% chrominance
standard color bar signal)
AUDIO input
Temperature
0 °C to 35 °C (32 °F to 95 °F)
Recommended temperature
20 °C to 30 °C (68 °F to 86 °F)
Humidity 30% to 85% (no condensation)
Phono jack (1), –5 dBu 47 kΩ or higher
OPTION IN connector
D-sub 9-pin (1), female
OPTION AUDIO IN connector
Phono jack (1), –5 dBu 47 kΩ or higher
External synchronized input connector
BNC type (1), 0.3 to 4 Vp-p
bipolarity ternary or negative
polarity binary
Pressure
700 hPa to 1060 hPa
Storage and transport conditions
Temperature
–20 °C to +60 °C (–4 °F to +140 °F)
Humidity 0% to 90%
Pressure
700 hPa to 1060 hPa
HDMI IN connector
Accessories supplied
HDMI (1)
AC power cord (1)
AC plug holder (1)
Operating Instructions (1)
CD-ROM (1)
PARALLEL REMOTE input connector
Parallel remote
Modular connector 8-pin (1)
Using the CD-ROM Manual (1)
Optional accessories
Output
LINE output connectors
Mounting bracket MB-529
SDI input adaptor BKM-320D
23
Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
HD/SD-SDI input adaptor BKM-
341HS
Design and specifications are subject to change without
notice.
Note
Always verify that the unit is operating properly before
use. SONY WILL NOT BE LIABLE FOR
DAMAGES OF ANY KIND INCLUDING, BUT
NOT LIMITED TO, COMPENSATION OR
REIMBURSEMENT ON ACCOUNT OF THE LOSS
OF PRESENT OR PROSPECTIVE PROFITS DUE
TO FAILURE OF THIS UNIT, EITHER DURING
THE WARRANTY PERIOD OR AFTER
EXPIRATION OF THE WARRANTY, OR FOR
ANY OTHER REASON WHATSOEVER.
Pin assignment
PARALLEL REMOTE connector
8
1
Modular connector
(8-pin)
Pin number Functions
1
2
3
4
5
6
7
8
Designating LINE input signal
Designating HDMI input signal
Designating RGB/COMPONENT input signal
16:9
GND
4:3
Selecting NORMAL
Selecting OVER
For details on function allocations, see REMOTE menu
Wiring required to use the Remote Control
Connect the function you want to use with a Remote
Control to the Ground (Pin 5).
24
Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
Video signal formats
The unit is applicable to the following signal formats.
Total
lines
Active
lines
Scanning
format
System
Frame rate
Aspect ratio
16:9/4:3
Signal standard
575/50I (PAL)
EBU N10
(PAL: ITU-R BT.624)
625
525
575
483
25
30
2:1 interlace
2:1 interlace
*1
480/60I (NTSC)
SMPTE 253M
(NTSC: SMPTE 170M)
16:9/4:3
576/50P
480/60P
625
525
576
483
50
60
24
25
30
25
30
50
60
Progressive
Progressive
Progressive
Progressive
Progressive
2:1 interlace
2:1 interlace
Progressive
Progressive
16:9/4:3
16:9/4:3
16:9
ITU-R BT.1358
SMPTE 293M
*1
1080/24P
1125
1125
1125
1125
1125
750
1080
1080
1080
1080
1080
720
SMPTE 274M
1080/25P
16:9
SMPTE 274M
*1
1080/30P
16:9
SMPTE 274M
1080/50I
16:9
SMPTE 274M
*1
1080/60I
16:9
SMPTE 274M/BTA S-001B
SMPTE 296M
720/50P
16:9
*1
720/60P
750
720
16:9
SMPTE 296M
*1 Also supports frame rate 1/1.001.
Applicable DVI input signals
When a PC signal is input to the HDMI IN connector
using a DVI conversion cable
Input
BKM-
320D
BKM-
System
Signal standard
341HS
1080/50I
–
–
–
–
a
a
a
a
SMPTE 292M
SMPTE 292M
SMPTE 292M
SMPTE 292M
Dot clock
Resolution
fH (kHz)
fV (Hz)
*1
(MHz)
28.322
36.000
40.000
65.000
108.000
1080/60I
720 × 400 70Hz
800 × 600 56Hz
800 × 600 60Hz
1024 × 768 60Hz
1280 × 1024 60Hz
31.469
35.156
37.879
48.363
63.981
70.087
56.250
60.317
60.004
60.020
720/50P
*1
720/60P
a : Can be input
– : Cannot be input
*1 The frame rate is also compatible with 1/1.001.
Note
The sides of the displayed picture may be invisible
depending on the input signal.
When an optional input adaptor is conneted, the unit is
applicable to the following signal formats.
When BKM-320D/BKM-341HS is connected
Input
BKM-
320D
BKM-
341HS
System
Signal standard
575/50I
a
a
–
a
a
a
a
a
a
a
SMPTE 259M
SMPTE 259M
SMPTE 292M
SMPTE 292M
SMPTE 292M
SMPTE 292M
SMPTE 292M
*1
480/60I
*1
1080/24PsF
1080/25PsF
–
*1
1080/24P
–
1080/25P
–
*1
1080/30P
–
25
Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
|