Sony Camera Accessories HDCU 900 User Manual

HD CAMERA CONTROL UNIT

HDCU-900

SD ANALOG INTERFACE UNIT

HKCU-901

HD ANALOG INTERFACE UNIT

HKCU-902

FRAME RATE CONVERTER UNIT

HKCU-903

LINE CONVERTER UNIT

HKCU-904

MAINTENANCE MANUAL

1st Edition (Revised 2)

Download from Www.Somanuals.com. All Manuals Search And Download.

For HDCU-900

Laser Diode Properties

Material

: In GaAsP

Wave length

: 1310 40 nm

Emission duration : Continuous

Laser output power: _8 dBm

For HDCU-900

CLASS 1

LASER PRODUCT

LASER KLASSE 1

PRODUKT

This camera control unit is classified as a CLASS 1

LASER PRODUCT.

The CLASS 1 LASER PRODUCT label is located on the

rear panel.

For HDCU-900

CAUTION

Use of controls or adjustments or performance of

procedures other than those specified herein

may result in hazardous radiation exposure.

HDCU-900 MM

1 (P)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents

Manual Structure

Purpose of this manual ........................................................................................ 5 (E)

Related manuals................................................................................................... 5 (E)

Contents ............................................................................................................... 6 (E)

1. Service Overview

1-1. Tools......................................................................................................1-1 (E)

1-2. Board/Main Parts Layout ......................................................................1-2 (E)

1-3. Circuit Description ................................................................................1-4 (E)

1-3-1. HDCU-900 ...........................................................................1-4 (E)

1-3-2. HKCU-901 ...........................................................................1-5 (E)

1-3-3. HKCU-902 ...........................................................................1-5 (E)

1-3-4. HKCU-903 ...........................................................................1-5 (E)

1-3-5. HKCU-904 ...........................................................................1-5 (E)

1-4. Functions of the Indicators on the Boards.............................................1-6 (E)

1-4-1. AT-141 Board ......................................................................1-6 (E)

1-4-2. DPR-163 Board ....................................................................1-6 (E)

1-4-3. RC-86 Board ........................................................................1-9 (E)

1-4-4. IF-789A/789P Board (HKCU-901)....................................1-10 (E)

1-4-5. FC-83 Board (HKCU-903) ................................................1-10 (E)

1-5. Adjustment and Setting after Replacing the Boards ...........................1-12 (E)

1-5-1. When Replacing the AT-141 Board...................................1-12 (E)

1-5-2. When Replacing the RC-86 Board.....................................1-12 (E)

1-5-3. When Replacing the DPR-163 Board ................................1-12 (E)

1-5-4. When Replacing the IF-789A/789P Board (HKCU-901) ..1-12 (E)

1-6. Connecting/Disconnecting the Flexible Card Wire ............................1-13 (E)

1-7. Cleaning of Connector/Cable ..............................................................1-13 (E)

1-8. Notes for RX-53 Boards......................................................................1-15 (E)

1-9. Writing and Rewriting the PLD Internal Data ....................................1-15 (E)

1-10. Circuit Protective Elements.................................................................1-17 (E)

1-11. Notes on Repair Parts ..........................................................................1-18 (E)

1-12. Character Display Function.................................................................1-19 (E)

HDCU-900 MM

1 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

2. Replacement of Main Parts

2-1. Replacing the Switching Regulator.......................................................2-1 (E)

2-2. Replacing the Fuse ................................................................................2-2 (E)

2-3. Removing the Rear Panel ......................................................................2-3 (E)

2-4. Replacing the DC Fan (Rear Panel) ......................................................2-3 (E)

2-5. Replacing the PS-587 Board .................................................................2-5 (E)

2-6. Replacing the RX-53 Board ..................................................................2-6 (E)

2-7. Replacing the CAMERA Connector .....................................................2-8 (E)

3. Electrical Alignment

3-1. Preparation ............................................................................................3-1 (E)

3-1-1. Required Equipment.............................................................3-1 (E)

3-1-2. Notes on Adjustments ..........................................................3-1 (E)

3-1-3. Connection of Equipment ....................................................3-2 (E)

3-1-4. Initialization Settings ...........................................................3-3 (E)

3-2. Audio System Adjustment ....................................................................3-4 (E)

3-2-1. Microphone Level Adjustment ............................................3-4 (E)

3-2-2. Front Intercom Microphone Level Adjustment ...................3-5 (E)

3-2-3. RTS Intercom Adjustment ...................................................3-6 (E)

3-2-4. PGM Mix Level Adjustment................................................3-7 (E)

3-2-5. Side Tone Level Adjustment................................................3-8 (E)

3-3. Video and Reference Signal System Adjustment .................................3-9 (E)

3-3-1. HD-SDI Output VCO Free-run Adjustment ........................3-9 (E)

3-3-2. Clock (74 MHz) Duty Adjustment/AT Board .....................3-9 (E)

3-3-3. Clock (74 MHz) Duty Adjustment/DPR Board .................3-10 (E)

3-3-4. Prompter Level Adjustment ...............................................3-10 (E)

3-4. Video Signal System Adjustment (RC-86 Board) ..............................3-11 (E)

3-4-1. SD-SDI Output VCO Adjustment......................................3-11 (E)

3-4-2. SD-SDI Input VCO Free-run Adjustment..........................3-12 (E)

3-4-3. Main Clock (74 MHz) Duty Adjustment ...........................3-13 (E)

3-4-4. Return Clock (74 MHz) Duty Adjustment .........................3-13 (E)

3-4-5. PIX Output Level Adjustment ...........................................3-14 (E)

3-4-6. WF Output Level Adjustment ............................................3-15 (E)

3-4-7. STAIR CASE Adjustment .................................................3-15 (E)

3-5. SD Signal System Adjustment (HKCU-901)......................................3-16 (E)

3-5-1. VBS Output Level Adjustment ..........................................3-17 (E)

3-5-2. PIX Output Level Adjustment ...........................................3-17 (E)

3-5-3. WF Output Level Adjustment ............................................3-18 (E)

3-5-4. GRB Output Level Adjustment..........................................3-19 (E)

3-5-5. Y/R-Y/B-Y Output Level Adjustment ...............................3-20 (E)

3-5-6. Return Level Adjustment ...................................................3-21 (E)

HDCU-900 MM

2 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

3-6. HD Signal Input/Output Adjustment (HKCU-902) ............................3-24 (E)

3-6-1. Y/P_B/P_ROutput Level Adjustment .....................................3-24 (E)

3-6-2. GBR Output Level Adjustment..........................................3-25 (E)

3-6-3. SYNC Output Level Adjustment .......................................3-26 (E)

3-6-4. A/D Conversion Level Adjustment....................................3-27 (E)

3-6-5. Clock (74 MHz) Duty Adjustment.....................................3-27 (E)

3-7. Video Signal System Adjustment (HKCU-904) .................................3-28 (E)

3-7-1. Main Clock (74 MHz) Duty Adjustment ...........................3-28 (E)

3-7-2. Return Clock (74 MHz) Duty Adjustment .........................3-28 (E)

HDCU-900 MM

3 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual Structure

Purpose of this manual

This manual is the maintenance manual of the following models :

HD Camera Control Unit

SD Analog Interface Unit

HD Analog Interface Unit

Frame Rate Converter Unit

Line Converter Unit

HDCU-900

HKCU-901

HKCU-902

HKCU-903

HKCU-904

This manual is intended for use by trained system and service engineers, and

describes the information regarding the circuit description, character display func-

tion, replacement of main parts and electrical alignment.

Related manuals

Beside this Maintenance Manual, the following manuals are available for the unit.

. Operation Manual (Supplied with HDCU-900)

This manual describes how to operate the HDCU-900.

. Installation and Maintenance Manual (Supplied with HDCU-900)

This manual intended for use by trained system and service engineers describes

the information regarding the installation of the HDCU-900 and the information

required for initial services.

Part number: 3-204-285-XX

. “Camera System HDC-900 Series Maintenance Manual” CD-ROM

(Available on request)

This “Camera System HDC-900 Series Maintenance Manual” CD-ROM allows

you to search for the detailed information (parts list, semiconductor pin assign-

ments, block diagrams, schematic diagrams and board layouts) of the HD color

camera HDC-900/950, that of HD camera control unit HDCU-900 and that of

option board HKCU-901/902/903/904 for HDCU-900 that premises the service on

the component level.

In addition to the above-described information, you can view the PDF files of the

related manuals of the equipment models that are used in the HDC-900 series

camera system. (Contents are subject to change without notice.) For obtaining,

contact your local Sony Sales Office/Service Center.

. “Semiconductor Pin Assignments” CD-ROM (Available on request)

This “Semiconductor Pin Assignments” CD-ROM allows you to search for

semiconductors used in B&P Company equipment.

Semiconductors that cannot be searched for on this CD-ROM are listed in the

maintenance manual for the corresponding unit. The maintenance manual contains

a complete list of all semiconductors and their ID Nos., and thus should be used

together with the CD-ROM.

Part number: 9-968-546-XX

HDCU-900 MM

5 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

Contents

The following is a summary of the sections of this manual.

Section 1 Service Overview

Describes information about circuit description, on-board indicators, adjustments

after board replacement and character display functions.

Section 2 Replacement of Main Parts

Describes replacement of parts.

Section 3 Electrical Alignment

Describes the general information for electrical adjustment and the adjustment

procedure of this unit.

HDCU-900 MM

6 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

Section 1

Service Overview

1-1. Tools

Name

Sony P/N

Remark

Extension board BKP-7900

Extension board JX-428

Front extension board

J-6394-280-A

Front extension board

Used to check side B of the board.

Rear side extension board

For HDC-900/950

Extension board EX-525A

Extension board EX-738

Alignment sleeve remover HC-001

PLD download tool

A-8326-353-A

A-8327-351-A

J-6480-010-A

J-7120-140-A

For female connector

PLD data download cable

Commercially available

For cleaning optical contact block

(4 mm or less in diameter)

Cotton swab

HDCU-900 MM

1-1 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-2. Board/Main Parts Layout

DC fans

Switching regulator

HDCU-900 MM

1-2 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-2. Board/Main Parts Layout

No.

Board

Function

SDI-54A board (HDCU-900)

S/N : 10001- 11000 (UC), 40001- 41000 (CE)

SDI-82 board (HDCU-900)

HD Digital Interface

S/N : 11001- (UC), 41001- (CE)

DIF-102 board (HDCU-900)

ADA-59 board (HKCU-902)

SDI-54B board (HKCU-903)

SDI-54C board (HKCU-904)

RX-53 board (HDCU-900)

DIF-102 board (HDCU-900)

VDA-57 board (HKCU-901)

ADA-59 board (HKCU-902)

SDI-54C board (HKCU-904)

PS-587 board (HDCU-900)

DPR-163 board (HDCU-900)

RC-86 board (HDCU-900)

FC-83 board (HKCU-903)

LC-41 board (HKCU-904)

RC-86 board (HDCU-900)

IF-789A^*1/789P^*2board (HKCU-901)

LC-41 board (HKCU-904)

AT-141 board (HDCU-900)

MB-902 board (HDCU-900)

CN-2004 board (HDCU-900)

CN-2006 board (HDCU-900)

CN-2007 board (HDCU-900)

CN-2008 board (HDCU-900)

CN-2005 board (HDCU-900)

SD Digital Interface

HD Analog Interface

HD Digital Interface

Optical Interface

SD Digital Interface

SD Analog Interface

HD Analog Interface

HD Digital Interface

Power Supply

HD Video Processor

HD-SD Down Converter

Frame Rate Converter

Line Converter

HD-SD Down Converter

Composite Encoder

Line Converter

Syscon/Audio Processor/SG

Motherboard

Connector

*1 : For UC

*2 : For CE

The slot to be used of each board differs depending on the used system. For details, refer to Section 2-1,

“Setting the System Format” of the separate Installation and Maintenance Manual.

HDCU-900 MM

1-3 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-3. Circuit Description

1-3-1. HDCU-900

. AT-141 board

The AT-141 board performs the various controls using the CPU, such as controlling the communication

with the camera head, with the control panel and with the CNU, and the control of the respective circuit

boards inside the CCU.

The AT-141 board also performs the audio signal processing such as the D/A conversion of the MIC

audio signal coming from the camera, the A/D conversion of the PGM signal, the A/D and D/A conver-

sions of the INCOM audio, and the INCOM line switch with the external device. The AT-141 board

also performs interface processing of the TALLY signal.

The AT-141 board has an internal SG circuit for the HD and SD signal, establishes genlock between the

HD and SD, and also genlocks the system with the main reference that is input from the external source.

. PS-587 board

The PS-587 board is the power regulator that supplies +1.5 V and _2.0 V regulated powers that are

used for processing the serial data of the HD and SDI systems.

. RX-53 board

The RX-53 board is the interface board that has the function interface between the HD-SDI optical

signal and the camera head. The RX-53 board also performs the O/E and E/O conversions.

. DPR-163 board

The DPR-163 board interfaces the various signals with the camera head.

As to the HD video signal, it performs the processing of the two HD video channels of both the camera

picture and return picture. The processing includes the phase adjustment using the line memory and

exchange of the clock signal with another desired clock.

The DPR-163 board has a built-in color bar generator and performs the processing of the marker and

skin gate for the monitor.

It also performs embedding of the prompter signal into the signal of the return video signals and the

interface processing with the digital audio system.

. SDI-54A/SDI-82 board

The SDI-54A/SDI-82 board is an interface board for interfacing with the coaxial HD-SDI signal

supplied from external equipment.

It supplies the main line output signal, the monitor output signal and accepts the return (four systems) input,

the main reference input and the prompter input.

. RC-86 board

The RC-86 board performs the SD-conversion processing of the main line system HD signal and also

performs the HD-conversion processing of the SD signal of the return system.

As the interface with external equipment, it performs processing of the component SDI format signal.

The RC-86 board has a built-in color bar generator and a simplified composite encoder. These are used

to generate the composite analog signal for which the marker and skin gate processing has already been

performed, which are the two types used for monitoring.

. DIF-102 board

The DIF-102 board is an interface board used for interfacing the coaxial HD-SDI signal with external

equipment.

It accepts the SD-SDI main line output and the return (four systems) input, and also supplies the

composite analog output signal to be connected to the picture monitor and has a waveform monitor

control connector.

In addition, it has a SYNC output of one channel that can be switched between HD-SYNC and SD-SYNC.

HDCU-900 MM

1-4 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-3. Circuit Description

1-3-2. HKCU-901

. IF-789A/789P board

The IF-789A/789P board is used in combination with the RC-86 board for interfacing the SD signal of

the main line using an analog interface.

It has a built-in digital composite encoder and color bar generator that are used to generate the compos-

ite output signal, the component output signal and the monitoring output. It also performs D/A conver-

sion of these signals.

It has a return signal processing block that converts the analog composite input signal into the 4:2:2

digital component signal and interfaces it with the RC-86 board.

In addition, it has a built-in external sync circuit of the SC (sub-carrier).

. VDA-57 board

The VDA-57 board is an interface board that interfaces the SD analog signal with external equipment.

It supplies the composite and component SD analog signal, the monitor output, and SD-SYNC output,

and accepts the return input signals (four systems).

1-3-3. HKCU-902

. ADA-59 board

The ADA-59 board is not equipped with the corresponding front board as its pair. It performs the D/A

and A/D conversions of the HD signal. This is the interface board with the external analog equipment.

It accepts the component output of the two systems, monitor output and HD-SYNC output, and also

supplies the return (single channel, four systems).

1-3-4. HKCU-903

. FC-83 board

The FC-83 board is a frame conversion board that converts a 24P picture into a 60i picture using the 2

to 3 pull-down method.

The FC-83 board has three built-in converter circuits in total (two circuits for the main output and for

the circuit board in the bottom shelf of the main line system, and one conversion circuit for the return

system picture). In the return system circuit, the return signal undergoes reverse-conversion of that of

the main line signal.

The board is equipped with a monitor output for outputting the signals that have already undergone the

marker and skin gate processing to be used for monitoring.

It also has an auxiliary reference input circuit for operating at multiple frame frequency. The auxiliary

reference input circuit detects the frame sync point of both the main reference and sub reference

signals, and establishes the frame lock of the sub reference signal with the main reference signal.

. SDI-54B board

The SDI-54B board is an interface board that interfaces the coaxial HD-SDI signal with external equipment.

It supplies the main line output signal and the monitor output signal. It accepts the return (four systems)

input, sub reference input and supplies SYNC (two systems) output.

1-3-5. HKCU-904

. LC-41 board

The LC-41 board is a line conversion board that converts the 1080-60i or 540-60P picture into the 720-

60P picture. It contains two converter circuits (for the main line system and return system). In the return

system circuit, the return signal undergoes reverse-conversion of that of the main line signal.

. SDI-54C board

The SDI-54C board is an interface board that interfaces the coaxial HD-SDI signal with external equipment.

It supplies the main line output signal and the SYNC (two systems), and accepts the return (four

systems) input.

HDCU-900 MM

1-5 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-4. Functions of the Indicators on the Boards

1-4. Functions of the Indicators on the

Boards

1-4-2. DPR-163 Board

Board suffix: -11 through -14

1-4-1. AT-141 Board

MAIN OUTPUT

OPTICAL

CONDITION

DPR

SYSTEM

AUDIO PHASE

POWER POWER /1.001 60

PSF

540P 1035

CHU LOCK

CCU

CHU

REFERENCE

PHASE

MIC LEVEL

NORM NORM

CCU

TALK

WIRE

REF GEN

IN LOCK

REMOTE

LOCAL

INCOM

LEVEL CANCEL

POWER

/1.001

SELECT

MIN

PGM SIDE

ENG PROD

PRIVATE

FINE

CH-1

CH-2

MIX TONE

DPR-163 board (A side and panel side)

AT-141 board (A side and panel side)

When D813 and D821 light in red, be sure to clean the

CAMERA connector of the unit, the CCU connector of the

camera side and optical/electrical cable. It is also recom-

mended to clean them when the indicators light in yellow.

For the cleaning procedure, refer to Section 1-7.

D609 : GEN LOCK display

Lights up when external synchronization is established.

D611 : /1.001 display

Lights up when the frame frequency factor of the HD

signal is set to 1/1.001 times.

D801 : /1.001 display

Lights up when the frame frequency factor of the HD

signal is set to 1/1.001 times.

Set it with S603 on the AT-141 board. For details, refer to

Section 1-5-1, “AT-141 Board” of “Settings of Switches

and Controls on Boards” of the separate Installation and

Maintenance Manual.

Set it with S603 on the AT-141 board. For details, refer to

Section 1-5-1, “AT-141 Board” of “Settings of Switches

and Controls on Boards” of the separate Installation and

Maintenance Manual.

D612 : REF IN display

Lights up when the reference signal is input to the REFER-

ENCE IN connector on the rear panel of the unit.

D802 : 0

Factory use only

D802 : POWER display

Lights up when the voltage used on the board is normally

supplied.

HDCU-900 MM

1-6 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-4. Functions of the Indicators on the Boards

D803, D805, D807, D810 : MAIN OUTPUT display

Displays the frame frequency of the camera and the MAIN

HD output of the CCU.

D819 : 540P display

Lights up when the connected camera runs in 540P mode.

D803 lights up when the frequency is 30 Hz.

D805 lights up when the frequency is 25 Hz.

D807 lights up when the frequency is 24 Hz.

D810 lights up during progressive operation of the camera.

Set it with S805 on the DPR-163 board. For details, refer

to Section 1-5-2, “DPR-163 Board” of “Settings of Switch-

es and Controls on Boards” of the separate Installation and

Maintenance Manual.

D804 : 1

Factory use only

D820 : 8

Factory use only

D806 : 2

Factory use only

D821 : OPTICAL CONDITION (CHU) display

Displays the optical level received at the camera side.

(0 dBm = 1 mW)

D808 : 3

Factory use only

Lights in green : Normal (The optical reception level

should be _17 dBm or more)

D811 : 4

Factory use only

Lights in yellow :Normal (The optical reception level

should be within _17 dBm to _20 dBm.)

Lights in red :

Abnormal (The optical reception level

D812 : 5

should be less than _20 dBm.)

Factory use only

D813 : OPTICAL CONDITION (CCU) display

Displays the optical level received at the HDCU-900 side.

(0 dBm = 1 mW)

Attenuates about 0.5 dB for every 1 km of cable.

Attenuates about 0.5 dB for each relay connector.

Lights in green : Normal (The optical reception level

should be _17 dBm or more)

D822 : 9

Factory use only

Lights in yellow : Normal (The optical reception level

should be within _17 dBm to _20 dBm.)

D904 : SYSTEM POWER display

Lights in red :

Abnormal (The optical reception level

should be less than _20 dBm.)

Lights when the power supply unit and power supply of

the PS-587 board (1.5 V, _2V) are normal.

D907 : POWER display

Attenuates about 0.5 dB for every 1 km of cable.

Lights up when the voltage used on the board is normal.

Attenuates about 0.5 dB for each relay connector.

D814 : CHU LOCK display

Lights up when communication with the connected camera

is normally established.

D815 : 6

Factory use only

D817 : 1035 line display

Lights up when the number of active video lines of the

connected camera is 1035.

D818 : 7

Factory use only

HDCU-900 MM

1-7 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-4. Functions of the Indicators on the Boards

D813 : OPTICAL CONDITION (CCU) display

Displays the optical level received at the HDCU-900 side.

(0 dBm = 1 mW)

Lights in green : Normal (The optical reception level

should be _17 dBm or more)

Board suffix: -22 and later

Lights in yellow :Normal (The optical reception level

should be within _17 dBm to _20 dBm.)

Lights in red :

Abnormal (The optical reception level

should be less than _20 dBm.)

Attenuates about 0.5 dB for every 1 km of cable.

Attenuates about 0.5 dB for each relay connector.

D814 : CHU LOCK display

Lights up when communication with the connected camera

is normally established.

D817 : 1035 line display

Lights up when the number of active video lines of the

connected camera is 1035.

D819 : 540P display

MAIN OUTPUT

OPTICAL

CONDITION

DPR

SYSTEM

AUDIO PHASE

POWER POWER /1.001 60

PSF

540P 1035

CHU LOCK

Lights up when the connected camera runs in 540P mode.

CCU

CHU

DPR-163 board (A side and panel side)

Set it with S805 on the DPR-163 board. For details, refer

to Section 1-5-2, “DPR-163 Board” of “Settings of Switch-

es and Controls on Boards” of the separate Installation and

Maintenance Manual.

When D813 and D821 light in red, be sure to clean the

CAMERA connector of the unit, the CCU connector of the

camera side and optical/electrical cable. It is also recom-

mended to clean them when the indicators light in yellow.

For the cleaning procedure, refer to Section 1-7.

D821 : OPTICAL CONDITION (CHU) display

Displays the optical level received at the camera side.

(0 dBm = 1 mW)

Lights in green : Normal (The optical reception level

should be _17 dBm or more)

D801 : /1.001 display

Lights up when the frame frequency factor of the HD

signal is set to 1/1.001 times.

Lights in yellow :Normal (The optical reception level

should be within _17 dBm to _20 dBm.)

Abnormal (The optical reception level

Lights in red :

Set it with S603 on the AT-141 board. For details, refer to

Section 1-5-1, “AT-141 Board” of “Settings of Switches

and Controls on Boards” of the separate Installation and

Maintenance Manual.

should be less than _20 dBm.)

Attenuates about 0.5 dB for every 1 km of cable.

Attenuates about 0.5 dB for each relay connector.

D803, D805, D807, D810 : MAIN OUTPUT display

Displays the frame frequency of the camera and the MAIN

HD output of the CCU.

D803 lights up when the frequency is 30 Hz.

D805 lights up when the frequency is 25 Hz.

D807 lights up when the frequency is 24 Hz.

D810 lights up during progressive operation of the camera.

D904 : SYSTEM POWER display

Lights when the power supply unit and power supply of

the PS-587 board (1.5 V, _2V) are normal.

D907 : POWER display

Lights up when the voltage used on the board is normal.

HDCU-900 MM

1-8 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-4. Functions of the Indicators on the Boards

1-4-3. RC-86 Board

D815 : 1

Factory use only

D816 : 7

Factory use only

D817 : 2

Factory use only

D818 : 8

Factory use only

D819 : 3

Factory use only

D820 : 9

Factory use only

D821 : 4

Factory use only

D822 : 5

Factory use only

MAIN OUTPUT

525 625

LEFT

VERTICAL

RIGHT

POWER

30PSF 60P

LOCAL REMOTE SQ LB EC

HORIZONTAL

CENTER

DOWN

RC-86 board (A side and panel side)

D4 : POWER display

Lights up when the voltage used on the board is normally

supplied.

D809, D810, D811 : MAIN OUTPUT display

Displays the SD system.

D809 lights up when the SD system is set to 525/59.941

SDI.

D810 lights up when the SD system is set to 625/50I SDI.

D811 lights up during 30PsF operation of the camera.

For details of the SD system setting, refer to Section 2-1-2,

“SD System” of “Setting the System Format” of the

separate Installation and Maintenance Manual.

D813 : 0

Factory use only

D814 : 6

Factory use only

HDCU-900 MM

1-9 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-4. Functions of the Indicators on the Boards

1-4-4. IF-789A/789P Board (HKCU-901)

1-4-5. FC-83 Board (HKCU-903)

MAIN OUTPUT

FRAME FRAME

REF IN

REFERENCE

SC PHASE

VBS

RGB LEVEL

POWER

/1.001

PSF

REF IN

LOCK

LEVEL CHROMA SYNC

IF-789A/789P board (A side and panel side)

FC-83 board (A side and panel side)

D602 : BB REF IN display

D824 : POWER display

Lights up when the external sync mode is set to SD and the

reference signal for synchronizing the sub carrier is input.

Lights up when the voltage used on the board is normally

supplied.

D1005 : /1.001 display

Set it with S602 on the AT-141 board. For details, refer to

Section 1-5-1, “AT-141 Board” of “Settings of Switches

and Controls on Boards” of the separate Installation and

Maintenance Manual.

Lights up when the frame frequency factor of the HD

signal is set to 1/1.001 times.

Set it with S603 on the AT-141 board. For details, refer to

Section 1-5-1, “AT-141 Board” of “Settings of Switches

and Controls on Boards” of the separate Installation and

Maintenance Manual.

D701 : POWER display

Lights up when the voltage used on the board is normally

supplied.

HDCU-900 MM

1-10 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-4. Functions of the Indicators on the Boards

D1006, D1007, D1008, D1009, D1010 :

MAIN OUTPUT display

D1021 : 4

Factory use only

Displays the frame frequency setting of the frame convert

HD output of the CCU.

D1022 : 5

D1006 lights up when the frequency is 30 Hz.

D1007 lights up when the frequency is 25 Hz.

D1008 lights up when the frequency is 24 Hz.

D1009 lights up when the picture of the HD output is

progressive and the format is PsF (segment progressive).

D1010 lights up when the picture of the HD output is

progressive and the format is P (pure progressive).

Factory use only

Set it with S2 on the FC-83 board. For details, refer to

Section 1-5-5, “FC-83 Board” of “Settings of Switches and

Controls on Boards” of the separate Installation and

Maintenance Manual.

D1011 : FRAME LOCK display

Lights up when the frame phase of the main reference and

sub reference is detected normally.

D1012 : FRAME REF IN display

Lights up when the sub reference for frame lock is input.

D1013 : 0

Factory use only

D1014 : 6

Factory use only

D1015 : 1

Factory use only

D1016 : 7

Factory use only

D1017 : 2

Factory use only

D1018 : 8

Factory use only

D1019 : 3

Factory use only

D1020 : 9

Factory use only

HDCU-900 MM

1-11 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-5. Adjustment and Setting after Replacing the Boards

1-5. Adjustment and Setting after

Replacing the Boards

1-5-2. When Replacing the RC-86 Board

While referring to Section 2, “System Setup” of the

separate Installation and Maintenance Manual, readjust and

reset the following items.

After replacing each plug-in board, return the switches to

the setting before replacement. Also, readjust and reset the

following items.

Adjustment and setting items

2-4-4. Adjusting the Level of Signals for Waveform

Monitor

1-5-1. When Replacing the AT-141 Board

While referring to Section 2, “System Setup” of the

separate Installation and Maintenance Manual, readjust and

reset the following items.

. Adjusting the staircase signal

If required, adjust the following items too.

2-4-4. Adjusting the Level of Signals for Waveform

Monitor

. Adjusting the WF Output Signal Level

2-4-5. Adjusting the Level of Signals for Picture Monitor

Adjustment and setting items

2-2-1. Setting the Intercom System

. Selecting the intercom system

. Setting the input level of the PGM audio signal

. Selecting an intercom line to be connected to the

INTERCOM connector

1-5-3. When Replacing the DPR-163 Board

2-2-2. Setting the Microphone

. Controlling the microphone input level from the

remote control

While referring to Section 3, “Electrical Alignment”,

adjust the following item.

. Adjusting the microphone input level using the

MIC LEVEL switch

Adjustment item

3-3-3. Clock (74 MHz) Duty Adjustment/DPR Board

(Board suffix: -14 only)

. Setting the microphone output level

2-3-1. Setting the Tally System

2-3-2. Setting the Camera Number

2-4-2. Adjusting the Signal Phase

. Adjusting the sync signal phase

3-3-4. Prompter Level Adjustment

1-5-4. When Replacing the IF-789A/789P

Board (HKCU-901)

While referring to Section 3, “Electrical Alignment”,

adjust the following items.

Adjustment items

3-5-4. GRB Output Level Adjustment

3-5-6. Return Level Adjustment

While referring to Section 2, “System Setup” of the

separate Installation and Maintenance Manual, adjust the

following item.

Adjustment item

2-4-3. Level Adjustment of the VBS Signal

HDCU-900 MM

1-12 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-6. Connecting/Disconnecting the Flexible Card Wire

1-7. Cleaning of Connector/Cable

1-6. Connecting/Disconnecting the

Flexible Card Wire

1-7. Cleaning of Connector/Cable

The state of the optical connector while the receptor is

receiving signals can be checked using the indicators on

the DPR-163 board. (For details, refer to Section 1-4-2,

“DPR-163 Board” of “Functions of the Indicators on the

Boards” )

The flexible card wire is used to connect between the

following boards. Bending the flexible card wire may

result in shortening the lifespan. Be careful not to bend it.

. Between the CN-2004 and PS-587 boards

. Between the CN-2005 and PS-587 boards

. Between the CN-2006 and PS-587 boards

. Between the CN-2007 and PS-587 boards

. Between the CN-2008 and PS-587 boards

1 wire

When the relevant indicator lights in red or yellow, clean

the following optical contact blocks.

. CAMERA connector of the unit

. CCU connector of the camera side

. Optical/electrical cable

. Connection connector of RX-53 board

Disconnecting

When replacing the CAMERA connector or replacing the

RX-53 board assembly, cleaning is also required.

Follow the procedures below for cleaning.

1. Turn off the main power.

2. Slide portion A in the direction of the arrow to unlock

and pull out the flexible card wire.

Tools Required

Connecting

. Alignment sleeve remover HC-001

(for female connector)

. Do not insert the flexible card wire sideways.

. Confirm that there is no stain or dust on the contact

surface of the flexible card wire.

Sony P/N : J-6480-010-A

Insert the shorter nose end when removing/installing the

1. Slide portion A in the direction of the arrow, turn over

the contact surface of the flexible card wire, then

securely insert it into the connector.

alignment sleeve.

Grasp not the shock absorber portion of the remover but

the handle in use.

2. Return portion A to its original position and lock the

connector.

. Cotton swabs (commercially available)

Shock absorber

Handle

Use the shorter nose end.

Use a cotton swab whose diameter is about 4 mm.

If a cotton swab whose diameter exceeds 5 mm is used,

the cotton swab cannot be inserted into the end of the

connector and the tip of the optical contact cannot be

cleaned.

Contact surface

HDCU-900 MM

1-13 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-7. Cleaning of Connector/Cable

2. When the turn stops, pull out the remover in the

straight line forcedly.

Cleaning

Male connector

Clean the tip of the white optical contacts by a cotton swab

moistened with alcohol.

The alignment sleeve can be removed/reinstalled with

the sleeve itself attached to the tip of the remover.

Great care should be taken so as not to lose or damage

the alignment sleeve.

Optical contacts (white)

(Alignment sleeve: Sony P/N 9-980-074-01)

Alignment sleeve

Female connector

The optical contacts for female connector are in an unex-

posed state. In cleaning, it is necessary to be exposed by

removing the alignment sleeve in advance. Proceed as

follows.

1. Insert the alignment sleeve remover into the alignment

sleeve in the straight line and turn it clockwise.

3. Clean the tip of the white optical contacts by a cotton

swab moistened with alcohol.

Alignment sleeve

Optical contacts (white)

Alignment sleeve remover

4. Insert the remover with the alignment sleeve attached

to its tip, and push it until it clicks.

5. Rotate the remover counterclockwise to install the

alignment sleeve, and extract the remover.

Connection connector

Clean the optical contact block of the connector using a

cotton swab moistened with alcohol.

Optical contact (white)

HDCU-900 MM

1-14 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-8. Notes for RX-53 Boards

1-9. Writing and Rewriting the PLD Internal Data

1-8. Notes for RX-53 Boards

The electric parts mounted on the RX-53 board cannot be replaced or adjusted.

If the electric parts need to be replaced or adjusted, replace the entire unit.

1-9. Writing and Rewriting the PLD Internal Data

The write/rewrite method of the PLD (Programmable Logic Device) that is mounted on the DPR-163

board (board suffix: -22 and later) supports the e-Production (EPR) system.

If the parts listed below needs to be replaced and if PLD needs to be upgraded, contact your local Sony

Sales Office/Service Center.

The PLD that is mounted on the DPR-163 board (board suffix: -11 through -14) does not support the e-

Production system. If you want to write/re-write the internal data of the PLD, contact your local Sony

Sales Office/Service Center.

The part number of PLD (or ROM for PLD) in which data is not written yet, is shown in “ Spare Parts” of

e-Manual.

Therefore, if part replacement is required, write the data by the following procedure.

In the case of the PLD type that runs on the program stored in external ROM, data needs not to be written

only by replacing the part if the specific PLD only is defective.

e-Production system has the advantages shown below.

. To write/rewrite the PLD internal data:

1. The standard fixture (cable) can be used.

2. The standard software (PLD Download Tool) can be used.

. The PLD internal data is controlled in the Sony Database Server under the name Project file

(E_xxx_xxx_xx_xx).

. The printed circuit board is equipped with the standard connector (EPR connector) to write the PLD

internal data. The indication “EPR” is shown on the printed circuit board.

Corresponding PLD and PLD ROM list

Board Name

PLD/ROM

EPR Connector

Project File No.

Remarks

DPR-163

(Board suffix: -22 later)

IC201, 202, 203, CN702

204, 504, 608, 717/

IC704, 705, 706,

707, 708, 709^*

E_000_001_02_xx

* : IC704 through IC709 are the PLD ROMs.

HDCU-900 MM

1-15 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-9. Writing and Rewriting the PLD Internal Data

Data write procedure

Data write procedure in the PLD (or ROM for PLD) is outlined below.

For details of data write procedure, refer to “Download Tool Operating Instruction for Device Program-

ming”.

“Download Tool Operating Instruction for Device Programming” is available in the same site where the

PLD Download Tool software is available.

Equipment required

. PLD download fixture (Sony part number : J-7120-140-A) : The cable connected PC to this unit

When connecting the fixture to the HDCU-950, remove the fixture cable from the fixture itself. Con-

nect the opposite side to the fixture main unit before starting to use the fixture.

. A PC having parallel port.

A PC in which the PLD Download Tool software is already installed.

For the applicable OS and the operating environment, refer to “Download Tool Operating Instruction

for Device Programming”.

Step 1 Prepare the Project file.

Download the Project file from the Sony Database Server.

Step 2 Turn off the power of this unit. Connect the PC parallel port to the EPR connector of the target

board using the PLD download fixture (cable).

Step 3 Turn on the power of this unit.

Start the Download Tool software and read the Project file.

Step 4 Program the PLD (or ROM for PLD) with the Download Tool software.

Step 5 Upon completion of programming, check that error message is not displayed. Turn off the power

of this unit and back on.

HDCU-900 MM

1-16 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-10. Circuit Protective Elements

The positive characteristic thermistor (for power supply) functions as a circuit protective element on the

AT-141, DPR-163, RC-86, IF-789A/789P (HKCU-901), FC-83 (HKCU-903) and LC-41 (HKCU-904)

boards of the unit. The thermistor increases the internal resistance and limits the current flowing to the

circuits when an overcurrent flows or when the ambient temperature increases and the element reaches

the specified temperature. If the elements operates, turn off the main power and inspect the HDCU

internal circuit. After removing the cause of the equipment abnormality and the temperature of the

element decreases, turn on the power again and operate the unit correctly. It takes about 1 minute for the

elements to cool down after the main power is turned off.

Board

Ref. No.

Address

Protective circuit/equipment

AT-141

THP800

THP801

THP802

THP901

THP902

THP903

THP901

THP902

THP903

THP904

THP905

THP906

THP907

THP1

Circuit inside the board

DPR-163

(Board suffix: -11 through -14)

Circuit inside the board

DPR-163

(Board suffix: -22 and later)

RC-86

Circuit inside the board

THP2

IF-789A/789P

(HKCU-901)

THP701

FC-83 (HKCU-903)

LC-41 (HKCU-904)

THP821

THP601

Circuit inside the board

HDCU-900 MM

1-17 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-11. Notes for Repair Parts

1-11. Notes on Repair Parts

1. Safety Related Components Warning

Components marked ! are critical to safe operation. Therefore, specified parts should be used in the

case of replacement.

2. Standardization of Parts

Some repair parts supplied by Sony differ from those used for the unit. These are because of parts

commonality and improvement.

Parts list has the present standardized repair parts.

3. Stock of Parts

Parts marked with “o” at SP (Supply Code) column of the spare parts list may not be stocked.

Therefore, the delivery date will be delayed.

4. Harness

Harnesses with no part number are not registered as spare parts.

In need of repair, get components shown in the list and repair using them.

5. Destination Representation

The part indicated “For J/UC/CE” in the spare parts list is used in the unit written below.

For J : The part is used in a unit for Japan.

For UC : The part is used in a unit for the U.S.A. and Canada.

For CE : The part is used in a unit for regions except the above countries.

HDCU-900 MM

1-18 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-12. Character Display Function

The contents of the pages displayed on the SD analog

monitor are as follows.

The character generation circuit built into the unit can mix

character information such as the settings, state and self-

diagnosis of the unit with the SD video signal, output it

from the PIX OUT (RC-86 board output) and CHARAC-

TER OUTPUT connectors, and display it on the SD analog

monitor.

The character MIX function output from the PIX OUT

connector can be forcibly turned off by turning off the

S102-5 switch on the AT-141 board.

Page

Title

Display OFF (CHARACTER button OFF)

System Status

Auto & Diag

Camera Status

SD Signal Status

System Diag 1/3

System Diag 2/3

System Diag 3/3

AT Diag

When the SD analog monitor is connected to the CHAR-

ACTER OUT connector, only characters are displayed in

black and white.

DPR Diag

Operating procedure

Slot-2 Diag

To display the setting, state and self-diagnosis display of

the unit on the SD analog monitor, press the CHARAC-

TER button of the RCP so that the button lights.

To change the page, press the CHARACTER button of the

RCP. The page can also be changed by pressing the S131

switch on the AT-141 board.

When the CHARACTER button of the RCP is kept

pressed, the pages are changed continuously. After all the

pages are displayed, the cycling display stops on the final

page and the CHARACTER button of the RCP goes off.

To display the character information again, press the

CHARACTER button of the RCP.

Slot-3 Diag

Camera Diag

ROM Version

Required equipment

. Color monitor

Sony BVM-1911/2811 or equivalent (for NTSC)

Sony BVM-2011P/3011P or equivalent (for PAL)

. Remote control unit

Sony RCP-700 series

. HDVS camera system

HDC-900/950

The first page is blank. When selecting the first page, the

display of characters is OFF.

S102

S131

AT-141 board (A side)

HDCU-900 MM

1-19 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-12. Character Display Function

Page 1

Page 2

System Status Display

Auto & Diag Display

**Auto Black Balance**

Completed

* System Status *

HDC-900 23.98Hz(PsF)

GEN Lock :Free

DPR :1080-23.98(PsF)

FC :1080-59.94(Intr)

RC : 525-59.94(Intr)

* Diagnosis *

(Rear)

(Front)

AT : OK

DPR: OK

RC : OK

IF : OK

Return Setting

1:SD AN EC 2:SD AN EC

3:SD AN EC 4:SD AN EC

Alarm :None

ADA: None

No. Contents

Displays the progress of auto setup of the camera side.

No. Contents

Displays the self-diagnosis result of the AT-141 board

(OK/NG).^*2

Displays the type of camera connected to the unit.

(HDC-700/HDC-750/HDC-900/HDC-950/UNDEFINED)

Displays the self-diagnosis result of the DPR-163 board

(OK/NG).^*2

Displays the type of external sync signal.

(Free/SD Digital/HD Digital)

Displays the self-diagnosis result of the board mounted in

the second slot from the top of the front side (OK/NG).^*2

Displays the setup format of the DPR-163 board.^*1

Displays the setup format of the board mounted in the

second slot from the top of the front side.^*1

Displays the self-diagnosis result of the board mounted in

the third slot from the top of the front side (OK/NG).^*2

Displays the setup format of the board mounted in the

third slot from the top of the front side.^*1

Displays the self-diagnosis result of the board mounted in

the second slot from the top of the rear side (OK/NG).^*2

Displays the type of signal input to the RET INPUT 1

connector on the rear panel of the unit.

Displays the self-diagnosis result of the board mounted in

the third slot from the top of the rear side (OK/NG).^*2

Displays the type of signal input to the RET INPUT 2

connector on the rear panel of the unit.

*2 : For the contents of the self-diagnosis of each board, refer to pages 8

through 11 of the character display.

Displays the type of signal input to the RET INPUT 3

connector on the rear panel of the unit.

Displays the type of signal input to the RET INPUT 4

connector on the rear panel of the unit.

Page 3

Camera Status Display

Displays abnormal portions of the system detected during

self-diagnosis.

0dB

EVS

1/125

Off

Black

*1 : For details, refer to Section 2, “System Setup” of the separate

White

R: 0

G: 0

B: 0

Installation and Maintenance Manual.

R: 0

G: 0

B: 0

BLK

Flare

R: 0

G: 0

B: 0

DTL

-60

ND:1 F:1.3 ExOff CC:A

Contents

Displays information of GAIN, ND, CC, Extender, Shutter,

aperture, Write, Black, Flare, Blackγ, Detail, etc.

HDCU-900 MM

1-20 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-12. Character Display Function

Page 4

Page 5

SD Signal Status Display

System Diag (1/3) Display

: 0

EC: 0 H:A

SD Matrix

V:A

OFF

LEV

OFF

* System Diag 1/3 *

Optical Condition

CC Reduce

COR

SD Detail

Level

Limit

Lim-w

Lim-b

Camera

CCU

Crisp

LDgain 0!,

Fan Power

Timer

117H

LDKnee 0![

Ratio

Freq

No. Contents

Setting state of the aspect ratio of the SD signal

(SQ/LB/EC)

State of the optical receiving level of the camera and

camera control unit (OK/WARNING/NG)^*3

SQ : Squeeze

WARNING :The optical level is _17 to _20 dBm.

LB : Letter box

NG :

The state when the optical level is low and

EC : Edge crop

any signal waveform cannot be obtained

Displays the crop position too. (_99 to 99)

_99 :The cut-out position is in the leftmost position.

0 : Cuts out the center.

99 : The cut-out position is in the rightmost

position.

When either of WARNING or NG appears on the CCU

side, clean the connector or cable while referring to

Section 1-7.

When either of WARNING or NG appears on the camera

side, clean the connector or cable while referring to the

Maintenances Manual of the camera.

Setting state of the H down-converter interpolation filter

coefficient (A to E)

State of the fan of the power supply block and the fan of

the rear panel (OK/NG)

Setting state of the V down-converter interpolation filter

coefficient (A to E)

NG :

The fan of the switching regulator and the

fan of the rear panel are defective.

Setting state of SD GAMMA (_99 to 99)

Accumulated power supply time to the AT-141 board is

displayed.

Setting state of the linear matrix correction coefficient

(ON/OFF)

*3 : The optical sending/receiving state of the main unit also can be checked

using the indicator on the panel of the DPR-163 board. For details, refer

to Section 1-4-2, “DPR-163 Board” of “Functions of the Indicators on the

Boards”.

Setting state of the cross-color reducing function

(ON/OFF)

Setting state of the coring level of the cross-color

reducing (_99 to 99)

Setting state of the reducing level of the cross-color

reducing (_99 to 99)

Setting state of the detail function (ON/OFF)

Setting state of the detail level (_99 to 99)

Setting state of the detail limiter (_99 to 99)

Setting state of the detail crispening (_99 to 99)

Setting state of the level dependent knee (_99 to 99)

Setting state of the detail H/V ratio (_99 to 99)

Setting state of the detail boost frequency (_99 to 99)

Setting state of the detail white limiter (_99 to 99)

Setting state of the detail black limiter (_99 to 99)

Setting state of the level dependent gain (_99 to 99)

HDCU-900 MM

1-21 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-12. Character Display Function

Page 7

Page 6

System Diag (3/3) Display

System Diag (2/3) Display

* System Diag 2/3 *

* System Diag 3/3 *

Intercom

Camera Cable Connect

Data OK

Power ON

Camera CH1 PROD

MIC ON

CH2 PROD

Sense OK

RCP/CNU Calble Connect

Data OK

Power OK

MIC ON

Camera MIC Gain

CH1 60dB Local

CH2 60dB Local

No. Contents

Setting state of the intercom 1ch of the camera side

(ENG/PROD)

State of camera cable connection (Open/Short/NG)

Existence of data from the camera (__/Wait/Sense/OK)

Setting state of the intercom 2ch of the camera side

(ENG/PROD)

__ :

The communication with the camera cannot

be established.

Wait : The communication with the camera is being

Gain and control state of the microphone circuit of the

camera side (Remote/Local)

waited.

Sense :The communication with the camera is being

established.

State of the power supply of the camera (ON/OFF)

State of connection to the camera (OK/NG^*4)

Page 8

AT Diag Display

State of cable connection of the RCP/CNU connector of

the rear panel of the unit (Open/Connect)

Displays the details of self-diagnosis of the AT-141 board

of the unit.

Existence of the data from the RCP/CNU connector of

the rear panel of the unit (__/Wait/Sense/OK)

* AT Diag *

__ :

The communication with the equipment

connected to the RCP/CNU connector cannot be

established.

System Frequency 1.001

Ref.H Phase

HD-SD DLY

Ret Setting

SD Local

90H

Local

Wait : The communication with the equipment connect-

ed to the RCP/CNU connector is being waited.

Sense :The communication with the equipment connect-

ed to the RCP/CNU connector is being estab-

lished.

Marker Setting Local

HD ANA

Normal

WFM Mode

CCU Mode

State of the power supply of the RCP/CNU connector of

the rear panel of the unit (OK/NG)

No. Contents

*4 : When power of the camera is supplied from the outside too, NG

appears.

Setting state of the S603 switch on the AT-141 board

(1.001/1.000)^*5

Setting state of the S601 and S602 switches on the AT-

141 board (SD Local/SD Remote/HD Local/HD Remote)^*5

Setting state of delay amount (setting of the S120 switch

on the AT-141 board) when converting the format of the

HD-SDI signal (1Frame/90H)^*5

Setting state of the S110 switch on the AT-141 board

(Local/Remote) ^*5

Setting state of the S111 switch on the AT-141 board

(Local/Remote) ^*5

Setting state of the S103-4 switch on the AT-141 board

(Recall/HD ANA)^*5

State of the operation mode of the AT-141 board

(Normal/Test)

*5 : For details, refer to Section 1-5-1, “AT-141 Board” of “Settings of

Switches and Controls on Boards” of the separate Installation and

Maintenance Manual.

HDCU-900 MM

1-22 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-12. Character Display Function

Page 9

Pages 10 and 11

DPR Diag Display

Slot-2 Diag/Slot-3 Diag Display

Displays the details of self-diagnosis of the DPR-163

board of the unit.

Displays the details of self-diagnosis of the board mounted

in the second or third slot from the top of the front/rear

side of the unit.

* DPR Diag *

Dialog display

of the board

mounted in the

second slot from

the top of the

front side.

Slot Sence

CHU Format Setting

Local:24Hz(PsF)

CB Select

100%-Non-Split

MIC OUT Sel

D-OUT:Digital-Input

A-OUT:Analog-Input

* Slot-2 Diag *

(Refer to the

next page “a”

DPR Mode

Normal

through “c”.)

Rear : ADA

HD Analog1

HD Analog2

YCD

Displays the

details of self-

diagnosis of the

ADA-59 board.

(This is not

No. Contents

Whether the DPR-163 board is recognized

(None/NG/OK)

displayed when

a board other

than the ADA-59

board is mounted.)

Setting state of the S804 to S807 switches on the DPR-

163 board^*6

Setting state of the S810 switch on the DPR-163 board^*6

Setting of input signal that is output to DIGITAL AUDIO

OUT (Digital-Input/Analog-Input)

Dialog display of

the board mounted

in the third slot

from the top of the

front side.

(Refer to the

next page “a”,

“c” and “d”.)

Setting of input signal that is output to ANALOG AUDIO

OUT (Digital-Input/Analog-Input)

* Slot-3 Diag *

State of the operation mode of the DPR-163 board

(Normal/Test)

*6 : For details, refer to Section 1-5-2, “DPR-163 Board” of “Settings of

Switches and Controls on Boards” of the separate Installation and

Maintenance Manual.

Rear : ADA

HD Analog1

HD Analog2

Displays the

YCD

details of self-

diagnosis of the

ADA-59 board.

(This is not

displayed when

a board other

than the ADA-59

board is mounted.)

No. Contents

Setting state of switch S103-1 on the AT-141 board

(YCD/RGB)^*7

Setting state of switch S103-2 on the AT-141 board

(YCD/RGB)^*7

*7 : For details, refer to Section 1-5-1, “AT-141 Board” of “Settings of

Switches and Controls on Boards” of the separate Installation and

Maintenance Manual.

HDCU-900 MM

1-23 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-12. Character Display Function

a. When the RC-86 board is mounted in the

second or third slot from the top of the front

side of the unit

c. When the LC-41 board is mounted in the

second or third slot from the top of the front

side of the unit

Front: LC

Front: RC

Main IN : 1080/60i

OUT: 720/60P

Slot Sence

Ret IN : 720/60P

OUT: 1080/60i

No. Contents

Whether the RC-86 board is recognized (None/NG/OK)

No. Contents

State of the format of the line converter MAIN INPUT

signal

Setting state of the conversion format (setting of S2 on

the LC-41 board)^*8of the line converter MAIN OUTPUT

signal

b. When the FC-83 board is mounted in the

second slot from the top of the front side of

the unit

Setting state of the format (setting of S11 and S12 on the

LC-41 board)^*8of the RETURN VIDEO signal to be input

to the LC-41 board

Front: FC

State of the format of the RETURN VIDEO signal to be

output from the LC-41 board

Main IN :1080/24PsF

OUT:1080/60i

Sub IN :1080/60i

OUT:1080/60i

Ret IN :1080/60i

OUT:1080/60i

*8 : For details, refer to Section 1-5-6, “LC-41 Board” of “Settings of

Switches and Controls on Boards” of the separate Installation and

Maintenance Manual.

d. When the IF-789A/789P board is mounted in

the third slot from the top of the front side of

the unit

No. Contents

Front: IF

State of the format of the frame converter MAIN INPUT

signal

Slot Sence

Setting state of the conversion format (setting of S2/S3

on the FC-83 board)^*7of the frame converter MAIN

OUTPUT signal

State of the format of the frame converter SUB INPUT

signal

State of the conversion format of the frame converter

SUB OUTPUT signal

Setting state of the format (setting of S11 to S13 on the

FC-83 board)^*7of the RETURN VIDEO signal to be input

to the FC-83 board

No. Contents

Whether the IF-789A/789P board is recognized

(None/NG/OK)

State of the format of the RETURN VIDEO signal to be

output from the FC-83 board

*7 : For details, refer to Section 1-5-5, “FC-83 Board” of “Settings of

Switches and Controls on Boards” of the separate Installation and

Maintenance Manual.

HDCU-900 MM

1-24 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-12. Character Display Function

Page 12

Page 13

Camera Diag Display

ROM Version (HDC-700 Series) Display

HDC-700 SERIES

Displays the ROM versions of the unit and the peripheral

equipment of the unit.

* CAMERA Diag *

* ROM Version *

(CHU)

(ADP)

CHU

ADP

CCU

4.10

3.04

99.07.22

99.07.14

98.08.11

VA: OK

MX: OK

PR: OK

DL: OK

IE: OK

VD : OK

AU : OK

DAP: OK

HDC-900 SERIES

No. Contents

* CAMERA Diag *

Displays the ROM version of the camera.

OHB: OK

VDA: OK

DAD: OK

AU : OK

SG : OK

DPR: OK

SDI: OK

DAP: OK

VA : OK

AT : OK

Displays the ROM version of the camera adapter.

Displays the ROM (IC105, IC106/AT-141 board) version

of the HDCU-900.

ROM Version (HDC-900 Series) Display

Displays the ROM versions of the unit and the peripheral

equipment of the unit.

Contents

Displays the self-diagnosis result of the board on the camera

side that is sent from the camera by the Diag command without

change.

* ROM Version *

CHU

CCU

4.10

3.04

99.07.22

98.08.11

No. Contents

Displays the ROM version of the camera.

Displays the ROM (IC105, IC106/AT-141 board) version

of the HDCU-900.

HDCU-900 MM

1-25 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

Section 2

Replacement of Main Parts

2-1. Replacing the Switching Regulator

3. Fully loosen the four screws (with drop-safe) and

remove the switching regulator in the direction of the

arrow.

The components marked ! are critical to safe operation. If

you replace with parts other than the specified ones, fire or

electric shock may result.

PWH4 x 8

(with drop-safe)

When repairing or replacing the power supply block, set

the voltage. If the voltage is set incorrectly, a fire or

electric shock may result.

. When repairing or replacing the power supply block, set

to the same power supply voltage as that of repair shop

work bench.

. When delivering to the user, adjust the power supply

voltage to suit the user.

PWH4 x 8

(with drop-safe)

Gently remove or attach the power supply unit while

holding it by hand.

Otherwise, the unit may fall, causing an injury.

Switching regulator

If the power supply unit is not attached securely, the

contact resistance of the unit increases, which may result in

damage to parts or a fire. Tighten completely the fixing

screws of the power supply unit.

4. Set the two voltage selectors of the new switching

regulator as shown in the following figure.

5. Attach the switching regulator in reverse order of step

Do not turn on the power before fixing the power supply

unit securely.

CAMERA TRANS

100 V

115 V

Replacement Part

Part :

Switching regulator

Part No. : ! A-8312-120-B

Replacement Procedure

1. Turn off the main power and disconnect the plug from

the outlet.

110-120 V

220-240 V

Wait for at least three minutes before starting replace-

ment, because there are electrically live blocks inside

the machine that could cause electric shock.

When using the unit at a voltage other than the specified

voltage, contact your local Sony Sales Office/Service

Center.

2. Remove the front panel. (Refer to Section 1 of the

Installation and Maintenance Manual.)

HDCU-900 MM

2-1 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

2-2. Replacing the Fuse

4. Insert a flat screwdriver into the groove of the fuse

holder, and rotate it in the direction of arrow A (by

about 90d) to unlock. (Fig. 1)

The components marked ! are critical to safe operation. If

you replace with parts other than the specified ones, fire or

electric shock may result.

5. Remove the fuse with the entire fuse holder. (Fig. 2)

6. Remove the fuse from the fuse holder. (Fig. 3)

Replacement Part

MAIN fuse

MAIN

CAMERA

The CAMERA fuse differs depending on the destination of

Fuse cover plate

the unit.

MAIN fuse

Part :

Fuse (6.3 A, 250 V)

PWH3 x 15

(with drop-safe)

Part No. : ! 1-576-233-11

CAMERA fuse

For UC

CAMERA fuse

Part :

Fuse (100 to 120 V, 6.3 A, 250 V)

Part No. : ! 1-576-233-11

Fig.1

Groove

Flat screwdriver

For CE

Fig.3

Part :

Fuse (220 to 240 V, 4 A, 250 V)

Fuse holder

Part No. : ! 1-576-231-11

Fuse

Replacement Procedure

Fig.2

Fuse holder

1. Turn off the main power and disconnect the plug from

the outlet.

Fuse holder

. Wait for at least three minutes before starting

replacement, because there are electrically live

blocks inside the machine that could cause electric

shock.

7. Attach a new fuse in reverse order of steps 3 to 6.

. Remove any foreign objects inside the machine that

could cause a short before replacement.

A spring is already attached in the fuse holder. When

attaching a new fuse, rotate the flat screwdriver in the

direction of arrow C (by about 90d) while pressing it in

the direction of arrow B to lock the fuse holder.

2. Remove the front panel. (Refer to Section 1 of the

Installation and Maintenance Manual.)

3. Fully loosen the screw (with drop-safe) and remove

the fuse cover plate.

Flat screwdriver

The MAIN and CAMERA fuses can be replaced in the

same way.

Fuse holder

HDCU-900 MM

2-2 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

2-3. Removing the Rear Panel

2-4. Replacing the DC Fan (Rear Panel)

2-3. Removing the Rear Panel

2-4. Replacing the DC Fan (Rear Panel)

1. Turn off the main power and disconnect the plug from

the outlet.

If the fan is defective, the temperature inside the unit will

rise. Touching the inside of the unit in this state may cause

a burn.

Replace the parts after turning off the power and cooling

the inside.

. Wait for at least three minutes before starting

replacement, because there are electrically live

blocks inside the machine that could cause electric

shock.

. If you bend or pull out the optical fiber cable

forcibly, disconnection may result. Handle the cable

carefully.

The fans that are used in the unit of the rear panel are

recommended replacement parts.

The lifespan of these fans is about 30,000 hours, which

means that the fans can be used for about three and a half

years if the power is on all the time, so as a guideline the

fans should be replaced every three and a half years.

2. Remove the boards and the blank panel from the rear

panel. (Refer to Section 1 of the Installation and

Maintenance Manual.)

3. Remove the cap from the CAMERA connector.

4. Remove the four screws and slide the rear panel

assembly in the direction of the arrow.

5. Remove the isolating sheet.

The rear panel is provided with the two DC fans.

Replacement Procedure

The isolating sheet is not fixed.

1. Turn off the main power and disconnect the plug from

the outlet.

6. Disconnect the connectors (CN1, CN16, CN18, CN19,

CN20, CN21, CN22) of the PS-587 board, then

remove the rear panel assembly.

Wait for at least three minutes before starting replace-

ment, because there are electrically live blocks inside

the machine that could cause electric shock.

PS-587 board

CN1

CAMERA

CN16

2. Remove the rear panel. (Refer to Section 2-3.)

connector

CN19

CN22

CN18

Only either the upper or the lower DC fan can be

replaced.

B3 x 5

CN21

CN20

Cap

B3 x 5

Rear panel assembly

Isolating

sheet

7. Reattach the rear panel in reverse order of the disas-

sembling procedure.

HDCU-900 MM

2-3 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

2-4. Replacing the DC Fan (Rear Panel)

Replacing the upper fan

Replacing the lower fan

1. Disconnect the harness from the two harness clamps.

2. Disconnect the connector (CN23) from the PS-587

board.

1. Disconnect the harness from the harness clamp.

2. Disconnect the connector (CN24) from the PS-587

board.

3. Remove the four screws and remove the DC fan.

Harness clamp

Harness clamps

PS-587 board

CN23

CN24

PS-587 board

B2.6 x 14

DC fan

B2.6 x 14

DC fan

B2.6 x 14

4. Attach a new DC fan in reverse order of steps 1 to 3.

Attach the DC fan in the direction shown below.

Upper fan

Lower fan

Upper fan

Lower fan

HDCU-900 MM

2-4 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

2-5. Replacing the PS-587 Board

5. Attach a new PS-587 board in reverse order of step 4.

When connecting the PS-587 board and MB-902

board, the MB-902 board may get out of position by

one pin. Connect the boards securely with great care.

Replacement Procedure

1. Turn off the main power and disconnect the plug from

the outlet.

Board-to-board

Be careful to

connectors of

MB-902 board

Connector

connection

at the correct

position

Connector

connection

at incorrect

position

connect the

connectors

because they

may get out of

position by one

pin.

Wait for at least three minutes before starting replace-

ment, because there are electrically live blocks inside

the machine that could cause electric shock.

Board-to-board

connectors of

PS-587 board

2. Remove the rear panel. (Refer to Section 2-3.)

3. Disconnect the connectors (CN23, CN24) of the DC

fan. (Refer to Section 2-4.)

4. Remove the three screws and remove the MB-902

board from the board-to-board connector connected to

the PS-587 board.

MB-902

board

Board-to-board connectors

PS-587 board

Board-to-board connectors

MB-902 board

PSW3 x 6

PS-587 board

HDCU-900 MM

2-5 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

2-6. Replacing the RX-53 Board

5. Remove the four screws and remove the CAMERA

connector from the optical unit.

CAMERA connector

. The electric parts mounted on the RX-53 board cannot

be replaced or adjusted.

If the electric parts need to be replaced or adjusted,

replace the entire unit.

Optical unit

. If you bend or pull out the optical fiber cable forcibly,

disconnection may result. Handle the cable carefully.

Replacement Procedure

1. Turn off the main power and disconnect the plug from

the outlet.

B3 x 5

Wait for at least three minutes before starting replace-

ment, because there are electrically live blocks inside

the machine that could cause electric shock.

B3 x 5

6. Disconnect the two connectors from the rod holder.

(Fig. 1)

7. Rotate each knurl block in the direction of arrow A to

remove the connector. (Fig. 2)

2. Remove the rear panel. (Refer to Section 2-3.)

3. Remove the three screws and slide the optical unit in

the direction of the arrow.

4. Disconnect the connectors (CN26, CN29) of the MB-

902 board and remove the optical unit.

The interconnection connector should be remain

connected to the mate connector (yellow). To avoid

the signal degration, do not touch an exposed tip of the

connector.

MB-902 board

Fig.1

CN29

CN26

Optical unit

Cream color

Light

B3 x 5

blue

B3 x 5

Rod holders

Connectors

Fig.2

Yellow

Interconnection

connector

Knurl block

HDCU-900 MM

2-6 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

2-6. Replacing the RX-53 Board

8. Remove the two screws (B3 x 5, shoulder screw) and

10. Attach the optical unit to the unit with three screws.

First, fasten temporarily the screws shown in the

figure, then fasten them securely.

remove the board assembly in the direction of the

arrow.

Be careful not to bend the cables (especially light blue

and cream color).

When connecting the connector (CN1) of the RX-53

board and the connector (CN6) of the MB-902 board,

the connectors may get out of position by one pin.

Connect the boards securely with great care.

MB-902 board

CN6

RX-53 board

assembly

B3 x 5

Optical unit

Shoulder screw

9. Attach the new RX-53 board assembly in reverse order

of steps 3 to 8.

B3 x 5

Fasten the screw

temporarily.

. Before connecting the connector, clean the tip of the

connector pin with alcohol.

. When connecting the connector, align the projecting

portion with the cut-out.

Connector connection

at incorrect position

Be careful to connect

Connector connection

the connectors

at the correct position

because they may

get out of position

CN6

by one pin.

RX-53 board

Cut-out

Projecting portion

CN1

Connectors

11. Attach the rear panel. (Refer to Section 2-3.)

HDCU-900 MM

2-7 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

2-7. Replacing the CAMERA Connector

If you bend or pull out the optical fiber cable forcibly,

disconnection may result. Handle the cable carefully.

Replacement Procedure

1. Follow steps 1 to 7 of Section 2-6, “Replacing the RX-

53 Board”.

The interconnection connector should be remain

connected to the mate connector (light blue and cream

color). To avoid the signal degration, do not touch an

exposed tip of the connector.

Fig.1

Cream color

Light

blue

Rod holders

Connectors

Yellow

Fig.2

Interconnection

connector

Knurl block

2. Attach a new CAMERA connector in reverse order of

removal.

For the notes during assembling, refer to step 9 of

Section 2-6 and higher.

HDCU-900 MM

2-8 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

Section 3

Electrical Alignment

3-1. Preparation

3-1-2. Notes on Adjustments

3-1-1. Required Equipment

. The measure should have already been calibrated.

. “3-1-4. Initialization Settings” have already been

finished.

Measures

. Digital oscilloscope (300 MHz or higher)

Tektronix TDS460A or equivalent

. HD waveform monitor

. The adjustment of the HDC-900 (or HDC-950) haven

already been finished.

. Types of the color bars to be output from the built-in SG:

Tektronix 1735HD/1730HD or equivalent

. SD waveform/Vector monitor

Tektronix 1780R or equivalent (for UC)

Tektronix 1781R or equivalent (for CE)

. SD signal generator

Tektronix TSG170A or equivalent (for UC)

Tektronix TSG271 or equivalent (for CE)

. Audio oscillator

Signal format

HD-SDI

100 %

75 %^*1

HD-Analog

SD-SDI (D1)

SD-Component-analog

(HKCU-901)

SD-Composite-analog

(HKCU-901)

75 %

75 % (SMPTE)

75 % (EBU)

Tektronix SG-5010 or equivalent

. Frequency counter

Advantest TR5821AK or equivalent

SD-Composite-analog

(HKCU-901)

100 %

*1 : When S811-1 on the RC-86 board is ON and S811-2 is OFF (factory

setting)

Related equipment

. HDVS color video camera

HDC-900 (or HDC-950)

. Master setup unit

. To adjust the unit, extend each plug-in board. Before

pulling out the boards, be sure to turn off the main

power.

. Before starting adjustment, warm up for about 10

minutes.

MSU-700A/750

. Before using the MSU-700A/750, check the version of

the ROM. For details, refer to Section 1-1, “Checking

the ROM Version” of the separate Installation and

Maintenance Manual.

Tools

. Front extension board BKP-7900

. Rear extension board EX-525A

(Sony P/N : A-8326-353-A)

. Extension board EX-738 (for HDC-900/950)

(Sony P/N : A-8327-351-A)

HDCU-900 MM

3-1 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

3-1. Preparation

3-1-3. Connection of Equipment

Adjusting the HDCU-900

STUDIO ZOOM

LENS

HD CAMERA

CONTROL UNIT

HDCU-900

Measure

OPTICAL FIBER

CABLE

COLOR

CAMERA

HDC-900

CCA-5 CABLE

(max. 200m)

MASTER SETUP UNIT

MSU-700A/750

Adjusting the HDCU-901

Signal generator

CAMERA

CONTROL

UNIT

REF IN/DIF-102

STUDIO ZOOM

LENS

Waveform/

Vector monitor

HDCU-900

WF/VDA-57

OPTICAL FIBER

CABLE

75 Z

SD ANALOG

INTERFACE

HKCU-901

COLOR

CAMERA

HDC-900

CCA-5 CABLE

(max. 200m)

MASTER SETUP UNIT

MSU-700A/750

Adjusting the HDCU-902

STUDIO ZOOM

LENS

HD CAMERA

CONTROL UNIT

HDCU-900

HD ANALOG

INTERFACE

HKCU-902

CABLE

COLOR

CAMERA

HDC-900

HD waveform

monitor

CCA-5 CABLE

(max. 200m)

MASTER SETUP UNIT

MSU-700A/750

75 Z

HDCU-900 MM

3-2 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

3-1. Preparation

3-1-4. Initialization Settings

When using the MSU-700A:

. Power supply and signal selector block

HDCU-900

ALL button

→

OFF (Dark)

ON (Lit)

OFF (Dark)

ON (Lit)

CAM PW button

TEST1 button

TEST2 button

BARS button

CLOSE button

When changing the switch settings from the customer’s

setting positions, it is recommended to write down the

customer’s setting positions in the following table. After

completing the adjustment, be sure to return the switches

to the customer’s setting positions.

. Camera/CCU circuit ON/OFF block

Board

Switch

Setting

during

adjustment

Customer

setting

DETAIL OFF button

KNEE OFF button

AUTO KNEE button

MATRIX OFF button

→

OFF (Lit)

ON (Dark)

OFF (Dark)

OFF (Lit)

AT-141

S102 to 105

S105-5 only

is ON

All others

are OFF

. AUTO SETUP block

LEVEL button

WHITE button

S110

REMOTE

0 dBu

RTS

→

OFF (Dark)

S301

S302

BLACK button

S401

S402

. Others

S403, 41

S404, 504

S501

GAMMA OFF button

→

OFF (Dark)

MASTER GAIN selector button →

OFF

When using the MSU-750:

S502

2ch

. Power supply and signal selector block

S503

PROD

LOCAL

ALL button

→

OFF (Dark)

S601

CAM PW button

TEST button

BARS button

CLOSE button

ON (Lit)

S602

OFF (Dark)

ON (Lit)

RC-86

S804

422YC

REMOTE

S805

IF-789A^*1/789P^*2S101-1

S101-2

S201

S202

S706

SMPTE

OFF

. AUTO SETUP block

LEVEL button

WHITE button

→

OFF (Dark)

3WAVE

BLACK button

Set the switches other than the above to the state when shipped from the

factory.

For details of the switch settings, refer to Section 1-5, “Settings of Switches

and Controls on Boards” of the separate Installation and Maintenance

Manual.

. Others

GAMMA OFF^*

→

(Not highlighted)

0 (0 dB)

*1 : for UC

*2 : for CE

MASTER GAIN^*

* : Press the function button and select it on the function menu display.

HDCU-900 MM

3-3 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

3-2. Audio System Adjustment

3-2-1. Microphone Level Adjustment

Measures : Oscilloscope, Audio oscillator

4. MIC2 level adjustment

Input a sine wave of 1 kHz, 220 mV p-p (_20 dBu)

from the audio oscillator to 15-pin (X), 16-pin (Y) and

17-pin (G) of the extension board (camera side).

Audio oscillator

Note

GND

600 Z

This adjustment is described on the premise that the output

GND

impedance of the audio oscillator is 600 Z.

Preparation

5. Measuring point : TP402 (D-3)/AT-141 or AUDIO

OUTPUT CH-2 connector/HDCU

rear panel

. Board extension : AT-141 board (front side)

. Board extension : AU-271 board (CAMERA side)

. S126 (MIC CH-1 LEVEL)/AT-141 board panel side →

MIN

Adjusting point : 1RV402 (D-2)/AT-141

Specifications : B = 1100 50 mV p-p

. S128 (MIC CH-2 LEVEL)/AT-141 board panel side →

MIN

. S402 (E-3)/AT-141 → 0 dBu

. S401 (D-3)/AT-141 → 0 dBu

Adjustment Procedure

1. MIC1 level adjustment

Input a sine wave of 1 kHz, 220 mV p-p (_20 dBu)

from the audio oscillator to 20-pin (X), 19-pin (Y) and

18-pin (G) of the extension board (camera side).

Setting after Adjustment

S401 (D-3), S402 (E-3)/AT-141 → Return to the original

setting.

Audio oscillator

600 Z

GND

2. Measuring point : TP401 (E-3)/AT-141 or AUDIO

OUTPUT CH-1 connector/HDCU

rear panel

Adjusting point : 1RV401 (E-2)/AT-141

Specifications : A = 1100 50 mV p-p

3. Remove the cable that is connected in step 1.

HDCU-900 MM

3-4 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

3-2. Audio System Adjustment

3-2-2. Front Intercom Microphone Level

Adjustment

Preparation

. MIC switch/HDCU front panel → CARBON

Measures : Oscilloscope, Audio generator

. Board extension : AT-141 board (front side)

MIC switch

Note

This adjustment is described on the premise that the output

MAIN

CAMERA

impedance of the audio oscillator is 600 Z.

GREEN TALLY

RED TALLY

DYNAMIC

OFF

CARBON

CABLE

ALARM

MIC

SHORT OPEN

MAIN

POWER

CAMERA

POWER

INTERCOM

INTERCOM connector

Adjustment Procedure

1. Connect the audio oscillator and the INTERCOM

connector on the HDCU front panel as shown in the

following figure.

TP608

TP613

220 uF

Audio generator

(16 V or more)

TP402

RV402

S401

RV604

RV603

600 Z

TP401

RV401

GND

RV605

RV602

S402

2. Input a sine wave of 1 kHZ, 220 mV p-p (_20 dBu)

from the audio oscillator.

3. Measuring point : TP503 (M-4)/AT-141

Adjusting point : 1RV506 (TALK LEVEL)/AT-141

board panel side

S404

S403

Specifications : A = 200 10 mV p-p

S504

S102

S603

S110

S101

S41

TP503

TP502

TP504

S602 S126

TP405

S601

REFERENCE

HD BB

PHASE

FINE

MIC LEVEL

NORM NORM

CCU

TALK

LEVEL

WIRE

REF GEN

IN LOCK

INCOM

SELECT

CANCEL

POWER

/1.001

REMOTE LOCAL

MIN

PGM

MIX

SIDE

TONE

ENG PROD

CH-1

CH-2

PRIVATE

AT-141 board (A side and panel side)

HDCU-900 MM

3-5 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

3-2. Audio System Adjustment

3-2-3. RTS Intercom Adjustment

2. PROD CANCEL adjustment

Measuring point : TP502 (M-3)/AT-141

Adjusting point : 1RV505 (2WIRE CANCEL 1)/

AT-141 board panel side

Measures : Oscilloscope, Audio generator

Specifications : A = Minimize

Note

. This adjustment is described on the premise that the

output impedance of the audio oscillator is 600 Z.

. When the intercom system is the RTS system, perform

this adjustment.

Preparation

3. ENG CANCEL adjustment

. MIC switch/HDCU front panel → CARBON

. Board extension : AT-141 board (front side)

. S504 (J-2)/AT-141 → RTS

S503 (INCOM SELECT)/AT-141 board panel side → ENG

4. Connect a resistance of 200 Z between A72-pin and

A73-pin of the extension board.

. S404 (J-1)/AT-141 → RTS

5. Input a sine wave of 1 kHz, 220 mV p-p (_20 dBu)

from the audio oscillator to 2-pin (X), 1-pin (Y) and 3-

pin (G) of the INTERCOM connector on the HDCU

front panel.

S503 (INCOM SELECT)/AT-141 board panel side → PROD

. S41 (L-3)/AT-141 → RTS

. S403 (L-2)/AT-141 → RTS

. Connect a resistance of 200 Z between A74-pin and

A75-pin of the extension board.

MIC switch

Audio oscillator

600 Z

GND

MAIN

CAMERA

GREEN TALLY

RED TALLY

DYNAMIC

OFF

CARBON

CABLE

ALARM

MIC

SHORT OPEN

6. Measuring point : TP405 (M-2)/AT-141

MAIN

POWER

CAMERA

POWER

Adjusting point : 1RV405 (2WIRE CANCEL 2)/

AT-141 board panel side

INTERCOM

Specifications : B = Minimize

INTERCOM connector

Adjustment Procedure

1. Input a sine wave of 1 kHz, 220 mV p-p (_20 dBu) from

the audio oscillator to 2-pin (X), 1-pin (Y) and 3-pin (G)

of the INTERCOM connector on the HDCU front panel.

Setting after Adjustment

After adjustment is completed, return the switches to the

original setting.

Audio oscillator

600 Z

GND

HDCU-900 MM

3-6 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

3-2. Audio System Adjustment

3-2-4. PGM Mix Level Adjustment

Measures : Oscilloscope, Audio oscillator

Note

This adjustment is described on the premise that the output

impedance of the audio oscillator is 600 Z.

Preparation

Board extension : AT-141 board (front side)

Adjustment Procedure

1. Input a sine wave of 1 kHz, 2.2 V p-p (0 dBu) from the

audio oscillator to C77-pin (X), D77-pin (Y) and D76-

pin (G) on the extension board of the AT-141 board.

Audio oscillator

600 Z

GND

TP608

TP613

2. Measuring points : TP504 (M-4)/AT-141 or 4-pin (X)/

INTERCOM connector, 3-pin (G)/

HDCU front panel

TP402

RV402

S401

RV604

RV603

Adjusting point : 1RV501 (PGM MIX)/AT-141

board panel side

Specifications : A = 100 20 mV p-p

TP401

RV401

RV605

RV602

S402

S404

S403

S504

S102

S603

These specifications are set for service. When using this

unit, adjust the level to suit the user.

S110

S101

S41

TP503

TP502

TP504

S602 S126

TP405

S601

REFERENCE

HD BB

PHASE

FINE

MIC LEVEL

NORM NORM

CCU

TALK

LEVEL

WIRE

REF GEN

IN LOCK

INCOM

SELECT

CANCEL

POWER

/1.001

REMOTE LOCAL

MIN

PGM

SIDE

TONE

ENG PROD

CH-1

CH-2

PRIVATE

MIX

AT-141 board (A side and panel side)

HDCU-900 MM

3-7 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

3-2. Audio System Adjustment

3-2-5. Side Tone Level Adjustment

2. Adjust the output level of the audio oscillator so that a

sine wave of 1 kHz, 200 mV p-p appears on TP503

(M-4) on the AT-141 board.

Measures : Oscilloscope, Audio oscillator

3. Measuring points : TP504 (M-4)/AT-141

Adjusting point : 1RV502 (SIDE TONE)/AT-141

board panel side

Note

This adjustment is described on the premise that the output

Specifications : A = 20 2 mV p-p

impedance of the audio oscillator is 600 Z.

Preparation

. MIC switch/HDCU front panel → CARBON

. Board extension : AT-141 board (front side)

MIC switch

These specifications are set for service. When using this

MAIN

CAMERA

unit, adjust the level to suit the user.

GREEN TALLY

RED TALLY

DYNAMIC

OFF

CARBON

CABLE

ALARM

MIC

SHORT OPEN

MAIN

POWER

CAMERA

POWER

INTERCOM

TP608

TP613

INTERCOM connector

TP402

RV402

S401

Adjustment Procedure

RV604

RV603

TP401

RV401

1. Connect the audio oscillator and the INTERCOM

connector on the HDCU front panel as shown in the

following figure and input a sine wave of 1 kHz, 220

mV p-p (_20 dBu).

RV605

RV602

S402

220 uF

Audio generator

(16 V or more)

S404

S403

S504

600 Z

S102

S603

GND

S110

S101

S41

TP503

TP502

TP504

S602 S126

TP405

S601

REFERENCE

HD BB

PHASE

FINE

MIC LEVEL

NORM NORM

CCU

TALK

LEVEL

WIRE

REF GEN

IN LOCK

INCOM

SELECT

CANCEL

POWER

/1.001

REMOTE LOCAL

MIN

PGM

SIDE

TONE

ENG PROD

CH-1

CH-2

PRIVATE

MIX

AT-141 board (A side and panel side)

HDCU-900 MM

3-8 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

3-3. Video and Reference Signal System Adjustment

3-3. Video and Reference Signal System

Adjustment

Setting after Adjustment

After finishing the adjustment, return the switches to the

original setting.

3-3-1. HD-SDI Output VCO Free-run

Adjustment

Measure : Frequency counter

3-3-2. Clock (74 MHz) Duty Adjustment/AT

Board

Preparation

Measure : Oscilloscope (20 MHz BWLimit: ON)

. Board extension: AT-141 board (front side)

. Remove the cable connected to the REFERENCE IN

connector on the HDCU rear panel.

Adjustment Procedure

. S603 (L-6)/AT-141 →/1000

. S601 (REMOTE/LOCAL)/AT-141 board panel side →

LOCAL

Measuring point : TP613 (B-7)/AT-141

Adjusting point : 1RV605 (E-6)/AT-141

Specifications : C = 1.65 0.04 Vdc

. S602 (REFERENCE)/AT-141 board panel side → HD

. S102-8 (K-6)/AT-141 → OFF

. Connect the measure as shown in the following figure.

. After turning on the power, wait for 10 minutes at least

and start adjustment.

A=B

GND

CH2

OUT

When this adjustment is completed, perform “3-3-3. Clock

(74 MHz) Duty Adjustment/DPR Board”.

Probe

Frequency

counter

Oscilloscope

Adjustment Procedure

1. HD (60) frequency adjustment

Measuring point : TP613 (B-7)/AT-141

Adjusting point : 1RV604 (D-5)/AT-141

Specifications : 74,250,000 10 Hz

2. S603 (L-6)/AT-141 → /1001

3. HD (59.94) frequency adjustment

Measuring point : TP613 (B-7)/AT-141

Adjusting point : 1RV603 (D-5)/AT-141

Specifications : 74,175,750 10 Hz

4. S602 (REFERENCE)/AT-141 board panel side→ BB

5. SD frequency adjustment

Measuring point : TP608 (B-8)/AT-141

Adjusting point : 1RV602 (E-9)/AT-141

Specifications : 27,000,000 10 Hz

HDCU-900 MM

3-9 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

3-3. Video and Reference Signal System Adjustment

3-3-3. Clock (74 MHz) Duty Adjustment/DPR

Board

3-3-4. Prompter Level Adjustment

Measures : SD waveform monitor

SD signal generator

Perform “3-3-2. Clock (74MHz) Duty Adjustment/AT

Board” before starting this adjustment.

Preparation

Measure : Oscilloscope (20 MHz BWLimit: ON)

Connect the SD signal generator (for UC : SMPTE color

bar/for CE : EBU color bar) to the PROMPTER IN

connector/SDI-54A/SDI-82.

Note

This adjustment corresponds to the DPR-163 board with

part No. suffix -14.

Adjustment Procedure

Measuring point : PROMPTER connector/CAMERA side

Adjusting point : 1RV501 (C-5)/DPR-163

Specifications : A = 140 1 IRE

(terminated at 75 Z) (for UC)

Adjustment Procedure

Measuring point : TP307 (F-8)/DPR-163

Adjusting point : 1RV301 (F-9)/DPR-163

Specifications : C = 1.65 0.04 Vdc

A = 1000 7 mV p-p

(terminated at 75 Z) (for CE)

[for UC]

[for CE]

A=B

GND

RV501

TP307

RV301

Suffix : -14

DPR-163 board (A side)

HDCU-900 MM

3-10 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

3-4. Video Signal System Adjustment (RC-86 Board)

3-4. Video Signal System Adjustment

(RC-86 Board)

Adjustment Procedure

1. Measuring point : TP501 (A-7)/RC-86

Adjusting point : 1RV501 (A-7)/RC-86

Specifications : 27.0 0.2 MHz

3-4-1. SD-SDI Output VCO Adjustment

Measure : Frequency counter

2. Measuring point : TP502 (A-8)/RC-86

Adjusting point : 1RV502 (A-8)/RC-86

Specifications : 27.0 0.2 MHz

Note

After replacing IC508 or IC510 on the RC-86 board only,

perform this adjustment.

Note

After finishing the adjustment and waiting for 10 minutes

at least, confirm that each specification is satisfied.

If the specifications are not satisfied, perform the adjust-

ment again.

Preparation

. Board extension : RC-86 board (front side)

. COR501 (B-8)/RC-86 → FREE RUN (Short between 2-

pin and 3-pin.)

Setting after Adjustment

. Connect the measure as shown in the following figure.

. After turning on the power, wait for 10 minutes at least

and start adjustment.

COR501 (B-8)/RC-86 → NORMAL

(Short between 1-pin and 2-pin.)

CH2

OUT

Probe

Frequency

counter

Oscilloscope

Suffix:14_

TP703

RV701

RV201

1 1

Suffix:14_

S803

RC-86 board (A side)

HDCU-900 MM

3-11 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

3-4. Video Signal System Adjustment (RC-86 Board)

3-4-2. SD-SDI Input VCO Free-run

Adjustment

Measure : Frequency counter

Note

After replacing IC601 on the RC-86 board only, perform

this adjustment.

Preparation

. Board extension : RC-86 board (front side)

. S110 (L-8)/AT-141 → LOCAL

. S101 (L-8)/AT-141 → All OFF

. COR601 (A-3)/RC-86 → FREE RUN (Short between 2-

pin and 3-pin.)

. Connect the measure as shown in the following figure.

. After turning on the power, wait for 10 minutes at least

and start adjustment.

CH2

OUT

Probe

Frequency

counter

Oscilloscope

TP608

TP613

Adjustment Procedure

TP402

RV402

S401

Measuring point : TP603 (C-1)/RC-86

Adjusting point : 1RV601 (B-3)/RC-86

Specifications : 27.0 0.2 MHz

RV604

RV603

TP401

RV401

RV605

RV602

S402

Note

After finishing the adjustment and waiting for 10 minutes

at least, confirm that each specification is satisfied.

If the specifications are not satisfied, perform the adjust-

ment again.

Setting after Adjustment

S404

S403

S504

S102

S603

. After finishing the adjustment, return the switches to the

original setting.

. COR601 (A-3)/RC-86 → NORMAL

(Short between 1-pin and 2-pin.)

S110

S101

S41

TP503

TP502

TP504

S602 S126

TP405

S601

AT-141 board (A side)

HDCU-900 MM

3-12 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

3-4. Video Signal System Adjustment (RC-86 Board)

3-4-3. Main Clock (74 MHz) Duty Adjustment

3-4-4. Return Clock (74 MHz) Duty

Adjustment

Measure : Oscilloscope (20 MHz BWLimit: ON)

Note

This adjustment corresponds to the RC-86 board with part

No. suffix -14.

This adjustment corresponds to the RC-86 board with part

No. suffix -14.

Preparation

. Board extension : RC-86 board (front side)

Adjustment Procedure

Measuring point : TP201 (C-6)/RC-86

Adjusting point : 1RV201 (C-6)/RC-86

Specifications : C = 1.65 0.04 Vdc

Measuring point : TP703 (B-2)/RC-86

Adjusting point : 1RV701 (B-2)/RC-86

Specifications : C = 1.65 0.04 Vdc

A=B

GND

A=B

GND

Suffix:14_

TP703

RV354

RV351

RV701

RV201

1 1

Suffix:14_

S803

RC-86 board (A side)

HDCU-900 MM

3-13 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

3-4. Video Signal System Adjustment (RC-86 Board)

3-4-5. PIX Output Level Adjustment

Measures : Oscilloscope, SD waveform monitor

Preparation

. Board extension : RC-86 board (front side)

. Board extension : DIF-102 board (rear side)

. 1RV354 (B-4)/RC-86 → mechanical center (ENC

LEVEL)

. S811-1 (M-6)/RC-86 → ON

. S811-2 (M-6)/RC-86 → OFF

. S802 (M-4)/RC-86 → 525

. PIX monitor select switch/MSU → ENC

. BARS button/MSU → ON

Adjustment Procedure

RV401

1. Video level adjustment

RV404

Measuring point : TP351 (A-5)/RC-86

Adjusting point : 1RV351 (B-5)/RC-86

Specifications : A = 1428 5 mV

DIF-102 board (A side)

A, B

Suffix:14_

TP703

RV354

RV351

RV701

RV201

1 1

Suffix:14_

2. PIX OUT level adjustment

Measuring point : PIX OUT connector/DIF-102

Adjusting point : 1RV401 (F-4)/DIF-102

Specifications : B = 100.0 0.5 IRE

(terminated at 75 Z) (for UC)

B = 700.0 3.5 mV

(terminated at 75 Z) (for CE)

Settings after Adjustment

. After finishing the adjustment, return the switches to the

original setting.

. PIX monitor select switch/MSU → ENC

. BARS button/MSU → ON

S803

Do not move 1RV354 (B-4) on the RC-86 board from the

mechanical center.

RC-86 board (A side)

HDCU-900 MM

3-14 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

3-4. Video Signal System Adjustment (RC-86 Board)

3-4-6. WF Output Level Adjustment

3-4-7. STAIR CASE Adjustment

Measures : Oscilloscope, SD waveform monitor

Measure : Oscilloscope

Preparation

Note

. Board extension : RC-86 board (front side)

. Board extension : DIF-102 board (rear side)

Perform temporarily this adjustment after repairing.

When the system is set up, perform the adjustment again

according to the characteristic of the waveform monitor.

1RV354 (B-4)/RC-86 → mechanical center (ENC LEVEL)

. S811-1 (M-6)/RC-86 → ON

. S811-2 (M-6)/RC-86 → OFF

. S802 (M-4)/RC-86 → 525

Preparation

. WF monitor select switch/MSU → ENC

. BARS button/MSU → ON

. Board extension : RC-86 board (front side)

. 1RV354 (B-4)/RC-86 → mechanical center (ENC

LEVEL)

. S802 (M-4)/RC-86 → 525

Adjustment Procedure

1. Video level adjustment

Adjustment Procedure

Measuring point : TP350 (A-4)/RC-86

Adjusting point : 1RV350 (B-4)/RC-86

Specifications : A = 1428 5 mV

Measuring point : TP352 (C-5)/RC-86

Adjusting point : 1RV353 (C-4)/RC-86

1RV352 (C-5)/RC-86

Specifications : A = 10.0 0.5 V p-p (1RV353)

B = 0 0.5 V dc (1RV352)

A, B

GND

2. WF OUT level adjustment

Measuring point : WF OUT connector/DIF-102

Adjusting point : 1RV404 (G-4)/DIF-102

Specifications : B = 100.0 0.5 IRE

(terminated at 75 Z) (for UC)

Settings after Adjustment

After finishing the adjustment, return the switches to the

original setting.

B = 700.0 3.5 mV

(terminated at 75 Z) (for CE)

Do not move 1RV354 (B-4) on the RC-86 board from the

mechanical center.

Settings after Adjustment

. After finishing the adjustment, return the switches to the

original setting.

. WF monitor select switch/MSU → ENC

. BARS button/MSU → OFF

Do not move 1RV354 (B-4) on the RC-86 board from the

mechanical center.

HDCU-900 MM

3-15 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

3-5. SD Signal System Adjustment (HKCU-901)

3-5. SD Signal System Adjustment

(HKCU-901)

Preparation

. Board extension : IF-789A/789P board (front side)

. S101-1 (M-9)/IF-789A/789P → ON

. S101-2 (M-9)/IF-789A/789P → SMPTE

. S708-1 (M-8)/IF-789A/789P → ON (CLEAR)

. S201 (M-9)/IF-789A/789P → OFF

. S202 (M-8)/IF-789A/789P → ON

. S705 (M-8)/IF-789A/789P → RGB

. S706 (M-8)/IF-789A/789P → 3WAVE

. S707 (M-7)/IF-789A/789P → NG

. 1RV205 (VBS LEVEL)/IF-789A/789P board panel side

→ Mechanical center

. 1RV210 (VBS CHROMA)/IF-789A/789P board panel

side → Mechanical center

. 1RV217 (RGB LEVEL)/IF-789A/789P board panel side

→ Mechanical center

RV63

RV61

RV121

RV64

RV65

RV124

RV66

RV62

. BARS button/MSU → ON

VDA-57 board (A side)

S707

1 1

REF IN

REFERENCE

SC PHASE

VBS

RGB LEVEL

POWER

LEVEL CHROMA

SYNC

IF-789A/789P board (A side and panel side)

HDCU-900 MM

3-16 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

3-5. SD Signal System Adjustment (HKCU-901)

3-5-1. VBS Output Level Adjustment

3-5-2. PIX Output Level Adjustment

Measures : SD waveform monitor, Vector monitor

Measure : SD waveform monitor

Preparation

Board extension : VDA-57 board (rear side)

. The VBS output level adjustment (section 3-5-2) should

be completed.

. PIX monitor select switch/MSU → ENC

. Board extension : VDA-57 board (rear side)

Adjustment Procedure

1. SYNC level adjustment

Adjustment Procedure

Measuring point : TP202 (B-6)/IF-789A/789P

Adjusting point : 1RV209 (C-6)/IF-789A/789P

Specifications : A = 571 3 mV (for UC)

A = 600 3 mV (for CE)

1. PIX signal level adjustment

Measuring point : PIX OUT connector/VDA-57

Adjusting point : 1RV121 (F-5)/VDA-57

Specifications : A = 100.0 0.5 IRE

(terminated at 75 Z) (for UC)

[for UC]

[for CE]

A = 700 3.5 mV

(terminated at 75 Z) (for CE)

[for UC]

[for CE]

2. Video level adjustment

Measuring point : TP202 (B-6)/IF-789A/789P

Adjusting point : 1RV202 (D-6)/IF-789A/789P

Specifications : B = 1429 5 mV (for UC)

B = 1400 5 mV (for CE)

2. PIX monitor select switch/MSU → R, G or B

3. SYNC level adjustment

3. VBS1 OUT level adjustment

Measuring point : VBS OUT1 connector/VDA-57

Adjusting point : 1RV62 (L-5)/VDA-57

Specifications : C = 100.0 0.5 IRE

(terminated at 75 Z) (for UC)

Measuring point: PIX OUT connector/VDA-57

Adjusting point: 1RV207 (C-6)/IF-789A/789P

Specifications:

B = 40.0 0.5 IRE

(terminated at 75 Z) (for UC)

B = 300.0 3.5 mV

C = 700.0 3.5 mV

(terminated at 75 Z) (for CE)

4. VBS2 OUT level adjustment

Measuring point : VBS OUT2 connector/VDA-57

Adjusting point : 1RV61 (M-4)/VDA-57

Specifications : D = 100.0 0.5 IRE

(terminated at 75 Z) (for UC)

D = 700.0 3.5 mV

(terminated at 75 Z) (for CE)

5. Chroma adjustment

Adjust the PHASE knob of the vector monitor so that

75% of the luminescent spot of the burst is aligned

with the axis.

4. Video level adjustment

Measuring point : PIX OUT connector/VDA-57

Adjusting point : 1RV204 (D-6)/IF-789A/789P

Specifications : C = 75.0 0.5 IRE

(terminated at 75 Z) (for UC)

Measuring point : VBS OUT1 connector/VDA-57

Adjusting point : 1RV208 (C-7)/IF-789A/789P

Specifications : The luminescent spot should be

located inside “4”.

C = 525.0 3.5 mV

(terminated at 75 Z) (for CE)

[for UC]

[for CE]

Setting after Adjustment

PIX monitor select switch/MSU → ENC

HDCU-900 MM

3-17 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

3-5. SD Signal System Adjustment (HKCU-901)

3-5-3. WF Output Level Adjustment

Measure : SD waveform monitor

Preparation

. The VBS output level adjustment (section 3-5-2) should

be completed.

. WF monitor select switch/MSU → ENC

. Board extension : VDA-57 board (rear side)

Adjustment Procedure

1. WF signal level adjustment

Measuring point : WF OUT connector/VDA-57

Adjusting point : 1RV124 (G-5)/VDA-57

Specifications : A = 100.0 0.5 IRE

(terminated at 75 Z) (for UC)

RV63

A = 700.0 3.5 mV

(terminated at 75 Z) (for CE)

RV61

RV121

RV64

RV65

[for UC]

[for CE]

RV124

RV66

RV62

VDA-57 board (A side)

2. WF monitor select switch/MSU → B

3. Video level adjustment

Measuring point : WF OUT connector/VDA-57

Adjusting point : 1RV203 (D-5)/IF-789A/789P

Specifications : B = 75 1 IRE

(terminated at 75 Z) (for UC)

B = 525 7 mV p-p

(terminated at 75 Z) (for CE)

Setting after Adjustment

S707

1 1

WF monitor select switch/MSU → ENC

S708-1 (M-8)/IF-789A/789P → OFF

IF-789A/789P board (A side)

HDCU-900 MM

3-18 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

3-5. SD Signal System Adjustment (HKCU-901)

3-5-4. GRB Output Level Adjustment

4. R signal level adjustment-2

Measuring point : R-Y/R OUTPUT connector/VDA-57

Adjusting point : 1RV65 (K-5)/VDA-57

Specifications : D = 700 5 mV p-p

(terminated at 75 Z)

Measure : SD waveform monitor

Preparation

Board extension : VDA-57 board (rear side)

5. B signal level adjustment-1

Measuring point : TP206 (D-8)/IF-789A/789P

Adjusting point : 1RV214 (D-8)/IF-789A/789P

Specifications : E = 1000 5 mV p-p

(100% color bar)

Adjustment Procedure

1. G signal level adjustment-1

Measuring point : TP205 (D-8)/IF-789A/789P

Adjusting point : 1RV216 (D-7)/IF-789A/789P

Specifications : A = 1000 5 mV p-p

(terminated at 75 Z) (100% color bar)

E, F

6. B signal level adjustment-2

Measuring point : B-Y/B OUTPUT connector/VDA-57

Adjusting point : 1RV66 (J-5)/VDA-57

Specifications : F = 700 5 mV p-p

(terminated at 75 Z)

2. G signal level adjustment-2

Measuring point : Y/G OUTPUT connector/VDA-57

Adjusting point : 1RV64 (H-5)/VDA-57

Specifications : B = 700 5 mV

(terminated at 75

3. R signal level adjustment-1

Measuring point : TP207 (D-7)/IF-789A/789P

Adjusting point : 1RV215 (D-7)/IF-789A/789P

Specifications : C = 1000 5 mV p-p

(100% color bar)

C, D

HDCU-900 MM

3-19 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

3-5. SD Signal System Adjustment (HKCU-901)

3-5-5. Y/R-Y/B-Y Output Level Adjustment

Adjustment Procedure

Measure : SD waveform monitor

1. Measuring point : Y/G OUTPUT connector/VDA-57

Measure level A. (about 100 IRE or

700 mV (terminated at 75 Z))

Preparation

(100% (Y) color bar)

. The GRB output level adjustment (section 3-5-4) should

be completed.

. Board extension : VDA-57 board (rear side)

. S705 (M-8)/IF-789A/789P → YCD

. S201 (M-8)/IF-789A/789P → OFF

A, B

2. S201 (M-8)/IF-789A/789P → ON

3. Y signal level adjustment

RV63

Measuring point : Y/G OUTPUT conenctor/VDA-57

Adjusting point : 1RV211 (C-7)/IF-789A/789P

Specifications : B = A (terminated at 75 Z)

(100% color bar)

RV61

RV121

RV64

RV65

RV124

RV66

RV62

VDA-57 board (A side)

When turning ON S201 (M-8) on the IF-789A/789P

(with SET UP added) and turning off (when SET UP is

not added), the level of A and B should not be

changed.

4. SYNC level adjustment

Measuring point : Y/G OUTPUT connector/VDA-57

Adjusting point : 1RV63 (F-2)/VDA-57

Specifications : C = 40 2 IRE

(terminated at 75 Z)

RV212 RV213

(100% (Y) color bar) (for UC)

C = 300 14 mV

(terminated at 75 Z)

(100% (Y) color bar) (for CE)

S707

1 1

IF-789A/789P board (A side)

HDCU-900 MM

3-20 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

3-5. SD Signal System Adjustment (HKCU-901)

5. R-Y signal level adjustment

3-5-6. Return Level Adjustment

Measuring point : R-Y/R OUTPUT connector/VDA-57

Adjusting point : 1RV213 (C-7)/IF-789A/789P

Specifications : D = 700 5 mV p-p (SET UP : ON)

(75% (R-Y) color bar) (for UC)

Measure : Oscilloscope

Preparation

D = 525 5 mV p-p

(75% (R-Y) color bar) (for CE)

. Board extension: IF-789A/789P board (front side)

. Board extension: VDA-55 board (CAMERA side)

. Connect the VBS OUT1 connector on the VDA-57

board and the RET INPUT1 connector on the VDA-57.

. Connect the SERIAL OUTPUT1 connector on the DIF-

102 board and the SERIAL RET INPUT1 connector on

the DIF-102 board.

. S811-1, 2 (M-6)/RC-86 → ON

6. B-Y signal level adjustment

Measuring point : B-Y/B OUTPUT connector/VDA-57

Adjusting point : 1RV212 (C-8)/IF-789A/789P

Specifications : E = 700 5 mV p-p (SET UP : ON)

(75% (B-Y) color bar) (for UC)

E = 525 5 mV p-p

(75% (B-Y) color bar) (for CE)

Suffix:14_

TP703

RV354

RV351

RV701

RV201

1 1

Suffix:14_

S803

RC-86 board (A side)

HDCU-900 MM

3-21 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

3-5. SD Signal System Adjustment (HKCU-901)

1. Input Level Adjustment

Adjustment Procedure

3. Return Level Adjustment (Y)

Adjustment Procedure

Measuring point : TP405 (G-4)/IF-789A/789P

Adjusting point : 1RV401 (G-4)/IF-789A/789P

Specifications : A = 1.56 0.02 V p-p

1. CONFIG button/MSU → ON

Set using MSU on the touch panel as follows.

RET1 : 2nd Slot (DIF-RET-1)

[

CCU] → [RET|SETTING] →

[for UC]

[for CE]

C, D

2. Phase Adjustment

2. Measuring point : TP37/extension board (VDA-55)

Measure level C. (about 1400 mV)

Adjustment Procedure

Measuring point : TP503 (G-1)/IF-789A/789P

Adjusting point : 1RV404 (L-3)/IF-789A/789P

Specifications : B = 0

3. CONFIG button/MSU → ON

Set using MSU on the touch panel as follows.

RET1 : 3rd Slot (VDA-RET-1)

CCU] → [RET|SETTING] →

[

[for UC]

[for CE]

4. Measuring point : TP37/extension board (VDA-55)

Adjusting point : 1RV402 (H-4)/IF-789A/789P

Specifications : D = C

5. Measuring point : TP37/extension board (VDA-55)

Adjusting point : 1RV501 (G-2)/IF-789A/789P

Specifications : E = 0

6. Repeat steps 4 and 5 until the specifications are

satisfied.

HDCU-900 MM

3-22 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

3-5. SD Signal System Adjustment (HKCU-901)

4. Return Level Adjustment (Pr)

Adjustment Procedure

2. Measuring point : TP43/extension board (VDA-55)

Measure level J. (about 1050 mV)

3. CONFIG button/MSU → ON

1. CONFIG button/MSU → ON

Set using MSU on the touch panel as follows.

RET1 : 3rd Slot (VDA-RET-1)

[CCU] → [RET|SETTING] →

Set using MSU on the touch panel as follows.

RET1 : 2nd Slot (DIF-RET-1)

[

CCU] → [RET|SETTING] →

4. Measuring point : TP43/extension board (VDA-55)

Adjusting point : 1RV406 (G-1)/IF-789A/789P

Specifications : K = J

F, G

5. Measuring point : TP43/extension board (VDA-55)

Adjusting point : 1RV502 (G-1)/IF-789A/789P

Specifications : L = 0

6. Repeat steps 4 and 5 until the specifications are

satisfied.

2. Measuring point : TP31/extension board (VDA-55)

Measure level F. (about 1050 mV)

3. CONFIG button/MSU → ON

Set using MSU on the touch panel as follows.

RET1 : 3rd Slot (VDA-RET-1)

[CCU] → [RET|SETTING] →

4. Measuring point : TP31/extension board (VDA-55)

Adjusting point : 1RV405 (G-1)/IF-789A/789P

Specifications : G = F

5. Measuring point : TP31/extension board (VDA-55)

Adjusting point: 1RV503 (G-1)/IF-789A/789P

Specifications : H = 0

6. Repeat steps 4 and 5 until the specifications are

satisfied.

5. Return Level Adjustment (Pb)

Adjustment Procedure

1. CONFIG button/MSU → ON

Set using MSU on the touch panel as follows.

RET1 : 2nd Slot (DIF-RET-1)

[CCU] → [RET|SETTING] →

J, K

S707

1 1

IF-789A/789P board (A side)

HDCU-900 MM

3-23 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

3-6. HD Signal Input/Output Adjustment (HKCU-902)

3-6. HD Signal Input/Output Adjustment

(HKCU-902)

2. P_Boutput level adjustment

Measuring point : P_B/B OUTPUT1 connector/ADA-59

Adjusting point : 1RV201 (H-2)/ADA-59

Specifications : A = 700 5 mV p-p

(terminated at 75 Z)

3-6-1. Y/P_B/P_ROutput Level Adjustment

Measure : HD waveform monitor

Preparation

. Board extension : ADA-59 board (rear side)

. BARS button/MSU → ON

. S1 (F-2)/ADA-59 → C

Adjustment Procedure

1. Y output level adjustment

3. P_Routput level adjustment

Measuring point : Y/G OUTPUT1 connector/ADA-59

Adjusting point : 1RV101 (G-3)/ADA-59

Specifications : A = 700 5 mV

(terminated at 75 Z)

Measuring point : P_R/R OUTPUT1 connector/ADA-59

Adjusting point : 1RV301 (K-2)/ADA-59

Specifications : C = 700 5 mV p-p

(terminated at 75 Z)

Setting after Adjustment

. S1 (F-2)/ADA-59 → 0

. BARS button/MSU → OFF

Suffix:14_

RV201

RV301

RV1

Suffix:14_

TP601

RV101

RV102

RV501

RV502

1 11 111

RV752

RV103

ADA-59 board (A side)

HDCU-900 MM

3-24 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

3-6. HD Signal Input/Output Adjustment (HKCU-902)

3-6-2. GBR Output Level Adjustment

3. B mix level adjustment

Measuring point : P_B/B OUTPUT1 connector/ADA-

Measure : HD waveform monitor

Adjusting point : 1RV202 (K-4)/ADA-59

Specifications : Portion D and portion E must be

flat (within 5 mV).

Preparation

. The Y/P_B/P_Routput level adjustment (section 3-6-1)

should be completed.

Portion D

. Board extension : ADA-59 board (rear side)

. S1 (F-2)/ADA-59 → 8

. BARS button/MSU → ON

Portion E

Adjustment Procedure

1. G mix level adjustment

Measuring point : Y/G OUTPUT1 connector/

ADA-59

4. B signal level adjustment

Adjusting point : 1RV102 (J-4)/ADA-59

1RV103 (J-4)/ADA-59

Measuring point : P_B/B OUTPUT1 connector/ADA-

Specifications : Portion A and portion B must be

Adjusting point : 1RV203 (L-4)/ADA-59

Specifications : F = 700 5 mV

flat (within 5 mV).

Portion A

Portion B

2. G signal level adjustment

Measuring point : Y/G OUTPUT1 connector/ADA-59

Adjusting point : 1RV104 (K-4)/ADA-59

Specifications : C = 700 5 mV

(terminated at 75 Z)

HDCU-900 MM

3-25 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

3-6. HD Signal Input/Output Adjustment (HKCU-902)

5. R mix level adjustment

3-6-3. SYNC Output Level Adjustment

Measuring point : P_R/R OUTPUT1 connector/

ADA-59

Measure : HD waveform monitor

Adjusting point : 1RV302 (L-4)/ADA-59

Specifications : Portion G and portion H must be

flat (within 5 mV or less).

Preparation

. Board extension : ADA-59 board (rear side)

Portion G

. BARS button/MSU → ON

Adjustment Procedure

Portion H

Measuring point : Y/G OUTPUT1 connector/ADA-59

Adjusting point : 1RV752 (F-4)/ADA-59

Specifications : A = 600 5 mV (terminated at 75

6. R signal level adjustment

Measuring point : P_R/B OUTPUT1 connector/ADA-

Adjusting point : 1RV303 (M-4)/ADA-59

Specifications : J = 700 5 mV (terminated at 75 Z)

Setting after Adjustment

. S1 (F-2)/ADA-59 → 0

. BARS button/MSU → OFF

BARS button/MSU → OFF

Suffix:14_

RV1

Suffix:14_

RV201

RV301

TP601

RV101

RV102

RV501

RV502

1 11 111

RV752

RV103

ADA-59 board (A side)

HDCU-900 MM

3-26 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

3-6. HD Signal Input/Output Adjustment (HKCU-902)

3-6-4. A/D Conversion Level Adjustment

Setting after Adjustment

Measure : Oscilloscope

. S1 (F-2)/ADA-59 → 0

. Return the setting on the setup menu of the HDC-900/

950.

Note

. RET1 button/camera → Return to the original setting.

. BARS button/MSU → OFF

Do not connect anything to the VTR connector of the camera.

Preparation

3-6-5. Clock (74 MHz) Duty Adjustment

. The Y/P_B/P_Routput level adjustment (section 3-6-1)

should be completed.

Measure : Oscilloscope (20 MHz BWLimit: ON)

. Board extension : VDA-55 board (HDC-900/950)

. Board extension : ADA-59 board (rear side)

. Connect the Y/G OUTPUT1 connector on the ADA-59

and the RET INPUT1 connector on the ADA-59.

. S1 (F-2)/ADA-59 → C

Note

This adjustment corresponds to the ADA-59 board with

part No. suffix -14.

. BARS button/MSU → ON

. Set on the setup menu of the HDC-900/950 as follows.

TOP MENU : MAINTENANCE

Preparation

. Board extension : ADA-59 board (rear side)

PAGE :

ITEM :

VTR-26P (M9)

VIDEO SEL → RET (YPbPr)

Adjustment Procedure

. RET1 button/camera → ON

Measuring point : TP601 (C-3)/ADA-59

Adjusting point : 1RV1 (E-3)/ADA-59

Specifications : C = 1.65 0.04 Vdc

Adjustment Procedure

1. Measuring point : TP37/extension board (VDA-55)

Adjusting point : 1RV501 (B-3)/ADA-59

Specifications : A = 0 5 mV

A=B

GND

2. Measuring point : TP37/extension board (VDA-55)

Adjusting point : 1RV502 (B-4)/ADA-59

Specifications : B = 1400 1 0 mV

HDCU-900 MM

3-27 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

3-7. Video Signal Sytem Adjustment (HKCU-904)

3-7. Video Signal Sytem Adjustment

(HKCU-904)

3-7-2. Return Clock (74 MHz) Duty

Adjustment

3-7-1. Main Clock (74 MHz) Duty Adjustment

Measure : Oscilloscope (20 MHz BWLimit: ON)

Preparation

. Board extension : LC-41 board (front side)

Preparation

. Board extension : LC-41 board (front side)

Adjustment Procedure

Measuring point : TP309 (E-1)/LC-41

Adjusting point : 1RV301 (D-1)/LC-41

Specifications : C = 1.65 0.04 Vdc

Adjustment Procedure

Measuring point : TP1 (B-6)/LC-41

Adjusting point : 1RV1 (B-5)/LC-41

Specifications : C = 1.65 0.04 Vdc

A=B

GND

A=B

GND

RV1

TP1

RV301

TP309

LC-41 board (A side)

HDCU-900 MM

3-28 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

SAFETY CHECK-OUT

After correcting the original service problem,

perform the following safety checks before

releasing the set to the customer :

Check the metal trim, “metallized” knobs,

screws, and all other exposed metal parts for AC

leakage. Check leakage as described below.

LEAKAGE TEST

The AC leakage from any exposed metal part to

earth ground and from all exposed metal parts to

any exposed metal part having a return to

chassis, must not exceed 3.5 mA. Leakage

current can be measured by any one of three

methods.

1. A commercial leakage tester, such as the

Simpson 229 or RCA WT-540A. Follow the

manufacturers’ instructions to use these

instruments.

2. A battery-operated AC milliammeter. The

Data Precision 245 digital multimeter is

suitable for this job.

3. Measuring the voltage drop across a resistor

by means of a VOM or battery-operated AC

voltmeter. The “limit” indication is 5.25 V, so

analog meters must have an accurate low-

voltage scale. The Simpson 250 and Sanwa

SH-63Trd are examples of a passive VOM

that is suitable. Nearly all battery operated

digital multimeters that have a 20 V AC range

are suitable. (See Fig. A)

To Exposed Metal

Parts on Set

voltmeter

(5.25V)

0.15 µF

1.5 kZ

Earth Ground

Fig A. Using an AC voltmeter to check AC leakage.

HDCU-900 MM

Download from Www.Somanuals.com. All Manuals Search And Download.

HDCU-900 (UC, J, CE)

HKCU-901 (UC, J, CE)

HKCU-902 (SY)

HKCU-903 (SY)

Printed in Japan

2003. 6 16

HKCU-904 (SY) J, E

9-968-566-03

Sony Corporation

B&P Company

Download from Www.Somanuals.com. All Manuals Search And Download.

Sharp Flat Panel Television LC 15A2U User Manual
Shure Microphone A95U User Manual
Silvercrest Clock Radio KH 2281 User Manual
Sony Camcorder PJ710 User Manual
Sony Cordless Telephone SPP S2730 User Manual
Sony MP3 Player ZS H10CP User Manual
Sony Portable CD Player CFD S550L User Manual
StarTechcom Car Satellite TV System COMP2VGATV2 User Manual
Sterling Home Theater Server 8820024900 User Manual
Sylvania TV VCR Combo 6313CD User Manual