Sony CD Player CDP CE575 User Manual

CDP-CE575

SERVICE MANUAL

US Model

Canadian Model

AEP Model

Ver 1.1 2001.07

Model Name Using Similar Mechanism NEW

CD Mechanism Type

Base Unit Name

CDM59-5BD27

BU-5BD27

Optical Pick-up Name

PXR-104X

SPECIFICATIONS

General

Compact disc player

Power requirements

Power consumption

Dimensions (approx.)

(w/h/d)

120 V AC, 60 Hz

11 W

430 x 110 x 400 mm

(17 x 4 3/8 x 15 3/4 in.)

incl. projecting parts

5.2 kg (11 lbs 8 oz)

Laser

Semiconductor laser (λ =

780 nm)

Emission duration:

continuous

2 Hz to 20 kHz ± 0.5 dB

More than 93 dB

Less than 0.0045%

Frequency response

Dynamic range

Harmonic distortion

Mass (approx.)

Supplied accessories

Audio cord (2 phono plugs – 2 phono plugs) (1)

Remote commander (remote) (1)

R6 (size AA) batteries (2)

Outputs

Jack

type

Maximum

output level impedance

2 V Over 10

(at 50 kilohms) kilohms

Load

Design and specifications are subject to change

without notice.

ANALOG

OUT

Phono

jacks

DIGITAL

OUT

(OPTICAL) connector

Optical

output

Wave

length:

660 nm

–18 dBm

PHONES

Stereo

phone

jack

10 mW

32 ohms

COMPACT DISC PLAYER

9-929-586-12

2001G0500-1

C 2001.7

Sony Corporation

Home Audio Company

Shinagawa Tec Service Manual Production Group

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

SECTION 1

SERVICING NOTES

HOW TO OPEN THE DISC TABLE WHEN POWER

SWITCH TURNS OFF

NOTES ON HANDLING THE OPTICAL PICK-UP

BLOCK OR BASE UNIT

The laser diode in the optical pick-up block may suffer electro-

static break-down because of the potential difference generated

by the charged electrostatic load, etc. on clothing and the human

body.

Insert a tapering driver into the aperture of the unit bottom, and

turn it in the direction of the arrow (to OUT direction).

During repair, pay attention to electrostatic break-down and also

use the procedure in the printed matter which is included in the

repair parts.

table

The flexible board is easily damaged and should be handled with

care.

NOTES ON LASER DIODE EMISSION CHECK

The laser beam on this model is concentrated so as to be focused

on the disc reflective surface by the objective lens in the optical

pick-up block. Therefore, when checking the laser diode emis-

sion, observe from more than 30 cm away from the objective lens.

CAUTION

tapering driver

Use of controls or adjustments or performance of procedures

other than those specified herein may result in hazardous ra-

diation exposure.

*To close the disc table, turn the tapering

driver in the reverse direction (to IN direction).

LASER DIODE AND FOCUS SEARCH OPERATION

CHECK

This appliance is classified as a CLASS 1 LASER product.

The CLASS 1 LASER PRODUCT MARKING is located on

the rear exterior.

Carry out the “S curve check” in “CD section adjustment” and

check that the S curve waveforms is output three times.

MODEL IDENTIFICATION

– BACK PANEL –

Notes on chip component replacement

• Never reuse a disconnected chip component.

• Notice that the minus side of a tantalum capacitor may be dam-

aged by heat.

Part No.

Flexible Circuit Board Repairing

• Keep the temperature of the soldering iron around 270 ˚C dur-

ing repairing.

• Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).

Model

Part No.

4-233-720-0s

US model

• Be careful not to apply force on the conductor when soldering

or unsoldering.

Canadian model

AEP model

4-233-720-1s

4-233-720-2s

NOTES ON CLEANING OF OPTICAL PICK-UP LENS

Do not clean up the optical pick-up lens.

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

SHIPMENT MODE

Performed when returning the unit to the customer.

Custom File Erases all custom files and initializes settings.

Procedure:

1. Remove the discs from all trays.

2. While pressing the DISK SKIP button and PROGRAM but-

ton, press the POWER button to turn ON the power.

3. “NO DISC” is displayed, indicating that the mode has ended.

Note: “NO DISC” may be displayed even if there are discs on the

trays.

CD-TEXT TEST DISC

This unit is able to display the TEXT data (character information) written in the CD on its fluorescent indicator tube.

The CD-TEXT TEST DISC (TGCS-313:4-989-366-01) is used for checking the display.

To check, perform the following procedure.

Checking Method:

1. Set the test disc on a free tray, and chuck the disc.

2. Press the H button and playback the disc.

3. The following will be displayed on the fluorescent indicator tube.

Display : 1kHz/0 dB/ L&R

4. Turn the l AMS L knob to switch the track. The text data of each track will be displayed.

For details of the displayed contents for each track, refer to “Table 1 : CD-TEXT TEST DISC TEXT Data Contents” and “Table 2 : CD-

TEXT TEST DISC Recorded Contents and Display”.

Restrictions in CD-TEXT Display

In this unit, some special characters will not be displayed properly. These will be displayed as a space or a character resembling it. For

details, refer to “Table 2 : CD-TEXT DISC Recorded Contents and Display”.

Table 1 : CD-TEXT TEST DISC TEXT Data Contents (TRACKS No. 1 to 41:Normal Characters)

TRACK

No.

TRACK

No.

Displayed Contents

1kHz/0dB/L&R

Displayed Contents

1kHz/-90dB/L&R

20Hz/0dB/L&R

40Hz/0dB/L&R

100Hz/0dB/L&R

200Hz/0dB/L&R

500Hz/0dB/L&R

1kHz/0dB/L&R

5kHz/0dB/L&R

7kHz/0dB/L&R

10kHz/0dB/L&R

16kHz/0dB/L&R

18kHz/0dB/L&R

20kHz/0dB/L&R

1kHz/0dB/L&R

1kHz/-1dB/L&R

1kHz/-3dB/L&R

1kHz/-6dB/L&R

1kHz/-10dB/L&R

1kHz/-20dB/L&R

1kHz/-60dB/L&R

1kHz/-80dB/L&R

Infinity Zero w/o emphasis//L&R

Infinity Zero with emphasis//L&R

400Hz+7kHz(4:1)/0dB/L&R

400Hz+7kHz(4:1)/-10dB/L&R

19kHz+20kHz(1:1)/0dB/L&R

19kHz+20kHz(1:1)/-10dB/L&R

100Hz/0dB/L*

1kHz/0dB/L*

10kHz/0dB/L*

20kHz/0dB/L*

100Hz/0dB/R*

1kHz/0dB/R*

10kHz/0dB/R*

20kHz/0dB/R*

100Hz Square Wave//L&R

1kHz Square Wave//L&R

1kHz w/emphasis/-0.37dB/L&R

5kHz w/emphasis/-4.53dB/L&R

16kHz w/emphasis/-9.04dB/L&R

Note : The contents of Track No. 1 to 41 are the same as those of the current TEST DISC-their titles are displayed.

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

Table 2: CD-TEXT TEST DISC Recorded Contents and Display

(In this unit, some special characters cannot be displayed. This is no a fault.)

TRACK

No.

Recorded contents

Display

T All the same

X Y Z [ \ ] ^ _ (58····

T All the same

(A0····

! ” # $ % & ´

(21h to 27h)1kHz 0dB L&R

( ) + , – . / (28h to 2Fh)

0 1 2 3 4 5 6 7 (30h to 37h)

8 9 : ; < = > ? (38h to 3Fh)

@A B C D E F G (40h to 47h)

H I J K L M N O (48h to 4Fh)

P Q R S T U VW (50h to 57h)

X Y Z [ ¥ ] ^ _ (58h to 5Fh)

a b c d e f g (60h to 57h)

′

h i j k l m n o (68h to 6Fh)

p q r s t u v w (70h to 77h)

x y z { I }

(78h to 7Fh)

i ¢ £ ¤ ¥

are not displayed

i ¢ £ ¤ ¥

–

(A0h to A7h) 8859-1

(A8h to AFh)

9C ª

(A8····

•

µ ¶ • (B0h to B7h)

(B0····

′

†

(B8h to BFh)

(B8····

À Á Â Ã Ä ÅÆÇ (C0h to C7h)

È É Ê Ë Ì Í Î Ï (C8h to CFh)

(C0····

(C8····

D Ñ Ò Ó ÔÕ Ö

(D0h to C7h)

(D8h to DFh)

(D0····

Ø Ù Ú Û Ü Y

(D8····

à á â ã ä å æ ç (E0h to E7h)

è é ê ë ì í î ï (E8h to FFh)

∂ ñ ò ó ô õ ö ÷ (F0h to F7h)

(E0···· à á â ã ä å æ ç are not displayed

(E8···· è é ê ë ì í î ï are not displayed

(F0···· ∂ ñ ò ó ô õ ö ÷ are not displayed

ø ù ú û ü y

(F8h to FFh)

(F8···· ø ù ú û ü y

are not displayed

No.66

No.67

T All the same

No.99

T All the same

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

SECTION 2

GENERAL

This section is extracted from

instruction manual.

Parts Identification

Front Panel

The items are arranged in alphabetical order.

Refer to the pages indicated in parentheses ( ) for details.

CHECK qh (13)

PEAK SEARCH qk (15)

PHONES jack wh (10)

POWER 1 (7, 9, 16)

PROGRAM qd (9, 13, 18)

Remote sensor wa (6)

REPEAT qf (10, 18)

SHUFFLE qs (9, 10, 18)

TIME EDIT qg (14)

BUTTON DESCRIPTIONS

CLEAR qj (13, 14, 16, 17)

CONTINUE 2 (9, 13, 15, 18)

DISC 1–5 3 (9, 10, 13)

Disc compartment ws (9)

DISC SKIP 9 (9, 12, 13)

Display 4 (11)

EX-CHANGE 8 (12, 15)

FADER ql (14, 20)

MEGA CONTROL 0 (18, 19)

MENU wf (8, 16, 17)

A OPEN/CLOSE wj (7, 9, 10, 11)

H 5 (9, 13, 15, 18, 20, 22)

X 6 (10, 15, 18, 22)

x 7 (10, 15, 18)

lAMSL (DISC) dial qa (10,

13, 15, 17, 18, 19)

m/M (AMS+/–) wd (10, 14, 17,

18)

TIME/TEXT w; (11)

X-FADE/NO DELAY wg (19, 20)

Rear Panel

2ND CD IN jacks 3 (8)

ANALOG OUT L/R jacks 4 (6)

CONTROL A1II jacks 1 (6, 20)

DIGITAL OUT OPTICAL jack 2 (7)

Mains lead 5 (6)

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

Remote Control

ANALOG OUT LEVEL +/– wh (6,

7, 10)

CD1/2/3 switch 1 (7)

CHECK 9 (13)

CLEAR ws (13, 14, 16, 17)

CONTINUE 3 (9, 13, 15, 18)

DISC/CAPS 6 (10, 17)

DISC SKIP +/– qh (9, 12, 13)

ENTER wa (17)

HIGH-LIGHT wd (12)

MEGA CONTROL 4 (18, 19)

MUSIC SCAN qa (10)

BUTTON DESCRIPTIONS

>10 8 (10, 13)

N wf (9, 13, 15, 18, 20, 22)

X qd (10, 15, 18, 22)

x wg (10, 15, 18)

./> qf (10, 13, 15, 17, 18,

19)

NAME INPUT qs (17)

NO DELAY ql (19, 20)

Number buttons 7 (10, 13, 17)

PROGRAM qj (9, 13, 18)

REPEAT 0 (10, 18)

SHUFFLE 2 (9, 10, 18)

TIME/TEXT/SPACE 5 (11, 17)

X-FADE qk (19, 20)

m/M qg (10, 14, 17, 18)

FADER/DEL w; (14, 20)

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

SECTION 3

DISASSEMBLY

• This set can be disassembled in the order shown below.

3-1. DISASSEMBLY FLOW

SET

3-2. CASE (409538)

(Page 9)

3-3. FRONT PANEL SECTION

(Page 9)

3-4. CD MECHANISM DECK

(CDM59-5BD27)

(Page 10)

3-6. BASE UNIT (BU-5BD27)

(Page 11)

3-5. MAIN BOARD

(Page 10)

3-7. TABLE ASSY

(Page 11)

3-8. SENSOR BOARD

(Page 12)

3-9. LOADING MOTOR BOARD

(Page 12)

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

3-2. CASE (409538)

3 case (409538)

2 two screws

1 two screws

(BVTP3 × 8)

(case3 TP2)

1 two screws

(case3 TP2)

3-3. FRONT PANEL SECTION

2 connector

4 claw

(CN601)

2 connector

(CN602)

1 wire (flat type) (15 core)

(CN801)

2 connectors

(CN351)

4 claw

3 four screws

(BVTP3 × 8)

5 front panel section

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

3-4. CD MECHANISM DECK (CDM59-5BD27)

9 CD mechanism deck

3 three screws

(CDM59-5BD27)

(BVTP3 × 8)

5 screw

(BVTP3 × 8)

2 three screws

(BVTP3 × 8)

4 Slide the tray until the screw

that fixes the table assy can be

seen through around hole

in the table assy.

7 wire (flat type) (21 core)

(CN301)

8 connector

(CN311)

1 Insert a tapering driver from the bottom of the chassis,

and turn it in the direction of the arrow until the base unit

goes down to the lowest position.

3-5. MAIN BOARD

3 two screws

(PTTWH3 × 6)

2 two screws

(BVTP3 × 8)

1 three screws

5 MAIN board

(BVTP3 × 8)

4 two PC board holders

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

3-6. BASE UNIT (BU-5BD27)

4 two screws

(PTPWH M2.6)

BU section

Note: When installing the BU

on the chassis, set the

5 base unit (BU-5BD27)

gear (U/D)

lever (lifter) in free

position, the gear (U/D)

in UP position, and insert

6 four compression springs (932)

the shaft

into the

groove of gear (U/D).

1 wire (flat type) (21 core)

(CN101)

2 two screws

(PTPWH M2.6)

7 holder (BU) assy

lever (lifter)

3-7. TABLE ASSY

q; clamp

7 two screws

(BTTP M2.6)

qa bracket (guide)

9 three screws

(BTTP M2.6)

8 bracket (guide 2)

gear

(loading C)

4 wire (flat type)

(6 core) (CN15)

qs table assy

5 screw

(BTTP M2.6)

2 two screws

6 bracket (guide)

(BTTP M2.6)

1 Slide the tray until the screw

that fixes the bracket (guide)

can be seen through a round

Note: When installing the table assy

on the chassis assy, engage

hole

in the table assy.

the gear (loading C) with the groove

by looking into the gear through

a hole e in the table assy.

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

3-8. SENSOR BOARD

1 screw

(PTPWH M2.6)

3 belt (rotary)

2 tray

5 SENSOR board

4 two screws

(BTTP M2.6)

3-9. LOADING MOTOR BOARD

3 two screws

(BTTP M2.6)

4 LOADING MOTOR board

1 belt (loading)

2 connector

(CN13)

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

SECTION 4

ASSEMBLY

Note: Follow the assembly procedure in the numerical order given.

ADJUSTING PHASE OF SWING GEAR AND GEAR (U/D)

5 stopper washer (FR)

4 Push fully the shaft of shaft gear and

align the hole shape of gear (loading B).

3 Let the swing gear through under the

6 screw

chassis h and engage its dowel

(PTPWH M2.6)

with the groove of rotary encoder.

2 Install the rotary encoder so that

its groove

comes to the position

shown in the figure.

1 Insert the shaft gear up to the

position where its shaft comes

out by 5 mm.

circle mark

8 screw

(PTPWH M2.6)

gear (RV)

swing gear

Fig. A

7 gear (U/D)

q; screw

(PTPWH M2.6)

9 gear (RV)

Note: Align swing gear, a circle mark

on the gear (U/D), and the teeth

of gear (RV) to the position

showing in the Fig. A.

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

SECTION 5

TEST MODE

Connecting Location:

ADJ MODE

– MAIN BOARD (Component Side) –

NOTE: This mode cannot be performed without a general remote com-

mander.

1. Chuck the CD first, and then turn OFF the power.

2. Short-circuit the test point TP (ADJ) of the MAIN board and

ground with a lead wire.

3. Press the [POWER] button to turn ON the power.

The CD is playback the 2nd track automatically and the ADJ

mode is set.

4. To exit the mode, press the [POWER] button to turn OFF the

power.

ADJ Mode Special Function Table

Button

DISC 1

DISC 2

DISC 3

DISC 4

DISC 5

TIME/TEXT

Function

RFDC display

Decision of Disc size (8/12 cm)

Change the slice level

Change the focus bias (high/middle/low)

Track jump (1st y 20th)

TRK off/on

Offset (VC), EF bias display

Offset (RF, FE, TRK) display

EX-CHANGE Focus bias down

DISK SKIP

X-FADE

EDIT

Focus bias up

Track gain up/down

Disc kind (aluminum/RW), side (8/12 cm) display

S-curve mode

CHECK

CLEAR

RFCK t GFS t error rate display

PEAK SERCH Best point of focus bias, jitter value display

FADER Auto gain display

TP (AFADJ)

R301

FLUORESCENT INDICATOR TUBE, LED ALL LIT,

AND KEY CHECK MODE

TP (ADJ)

1. Short-circuit the test TP (AFADJ) of the MAIN board and

ground with a lead wire.

2. Press the [POWER] button to turn ON the power.

The whole fluorescent indicator tube lights up.

3. All buttons have individual button numbers.

When a button is pressed, the button number is counted up

and displayed.

1 0

button number

Displays button number

When remote controller signals are received, “RM **” will be

displayed.

(** are the numbers corresponding to the remote controller

buttons)

When using the remote controller, switch the [CD1/2/3] switch

to CD1.

4. To exit the mode, press the [POWER] button to turn OFF the

power.

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

Buttons and Corresponding Button Numbers

All lit

Button

DISC1

Button Number or Display

DISC2

11 12 13 14 15

16 17 18 19 20

DISC3

DISC4

DISC5

Partial lighting 1

CONTINUE

SHUFFLE

PROGRAM

REPEAT

TIME/TEXT

EDIT

Light altemately

CHECK

CLEAR

PEAK SEARCH

FADER

Partial lighting 1 (grid check)

Partial lighting 1 (segment check)

EX-CHANGE

DISC SKIP

Partial lighting 2

Light altemately

X-FADE, NO DELAY 17

MEGA CONTROL 16

l AMS L (push) 29

l AMS L (rutn) When rotated clockwise: The music

calendar numerals light up in ascending

order.

Light altemately

When rotated counterclockwise: The music

calendar numerals light up in descending

order.

A OPEN/CLOSE

All lit (LED lighting)

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

AGING MODE

For the aging mode, three modes of all mode, disc table mode, and loading mode are available.

Disc table

mode

Code No. Status

All mode

CLOSE (Tray close)

TOC read

Access to last track

Play of last track (2 sec)

EX OPEN (Tray open while chucking)

EX SKIP (Disc tray rotate)

EX CLOSE (Tray close)

Access to first track

Play of first track (2 sec)

OPEN (tray open)

DISC SKIP (Disc tray rotate,

and change next disc)

The discs are selected in the order of DISC 1 → DISC 2 → DISC 3 → DISC 4 → DISC 5 → DISC 1....Empty trays are skipped.

But the order is random in the disc table mode.

This set has the Aging mode for operation check of the mechanism deck.

• If a failure occurred

The aging operation stops and a faulty status is displayed on the fluorescent indicator tube.

• If no failure occurs

The aging operation continues repeatedly.

Note: Do not use the test disc when performing aging.

Aging will not be performed properly if discs with tracks shorter than 4 seconds are used.

Procedure:

1. Press the [POWER] button and turn ON the power.

2. Set discs on all trays.

(More than two discs if five are not available)

3. All mode:

Press the [CHECK], [CONTINUE] and x buttons at the same time.

Disc table mode:

Press the [CHECK], [CONTINUE] and [DISC SKIP] buttons at the same time.

Loading mode:

Press the [CHECK], [CONTINUE] and [EX-CHANGE] buttons at the same time.

4. Aging starts, and the fluorescent indicator tube will display as follows.

display

(a)

(b)

(c)

(a) A : All mode

AD : Disc table mode

AL : Loading mode

NG : failure occurred

(b) Code No.

5. To exit the mode, press the [POWER] button to turn OFF the power.

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

MECHANISM DECK CHECK MODE

For the mechanism desk check mode, two modes of the disc table mode and the loading mode are available.

In the mechanism deck check mode, the disc table rotating time and the loading time in each section are measured and displayed.

Disc Table Mode

Procedure:

1. Press the [POWER] button while pressing three buttons of H , [^AOPEN/CLOSE], and [REPEAT] simultaneously.

2. Start the table mode, and turn to right then turn to left, and display rotating time as follows.

display

R5.7 L5.8

3. To release from this mode, press the [POWER] button to turn OFF the power.

Loading Mode

Procedure:

1. Press the [POWER] button while pressing three buttons of H , [^AOPEN/CLOSE], and [TIME/TEXT] simultaneously.

2. Start the loading mode and display as follows.

Operation

Start

Open and close CLOSE

Display

START

– –. –

1.9

BU up

BU UP

0.5

EX open

EX close

BU down

Open

EX OPEN 1.9

EX CLOSE 2.2

BU DOWN 0.4

OPEN

1.7

3. To change the display, turn the [

AMS

] knob.

4. To release from this mode, press the [POWER] button to turn OFF the power.

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

Ver 1.1 2001.07

SECTION 6

ELECTRICAL ADJUSTMENTS

Note:

Procedure:

1. CD Block is basically designed to operate without adjustment. There-

fore, check each item in order given.

2. Use PATD-012 disc (4-225-203-01) unless otherwise indicated.

3. Use an oscilloscope with more than 10MΩ impedance.

4. Clean the object lens by an applicator with neutral detergent when the

signal level is low than specified value with the following checks.

1. Set the test disc (PATD-012). Disc chucking operation is

complete, then press the [POWER] button to turn the power

off.

2. Connect an oscilloscope to test point TP (RFDC) and TP (VC)

on the BD board.

3. Connect between test point TP (ADJ) on the MAIN board and

GND by lead wire.

S Curve Check

4. Press the [POWER] button to turn the power on and enter the

ADJ mode, then playback the number two track automatically.

5. Confirm that oscilloscope waveform is clear and check the level

of between RFDC top and VC is correct or not.

Note: A clear RFDC signal waveform means that the shape “◊” can be

clearly distinguished at the center of the waveform.

Connection:

oscilloscope

BD board

TP (FE1)

TP (VC)

–

RFDC signal waveform

VOLT/DIV: 200 mV

TIME/DIV: 500 ns

Procedure:

1. Set the test disc (PATD-012). Disc chucking operation is

complete, then press the [POWER] button to turn the power

off.

2. Connect an oscilloscope to test point TP (FE1) and TP (VC)

on the BD board.

level: 1.15 ± 0.35 Vp-p

3. Connect between test point TP (ADJ) on the MAIN board and

GND by lead wire.

4. Press the [POWER] button to turn the power on and enter the

ADJ mode.

Checking Location: BD board

Then playback the number two track automatically, press the

x button to stop the playback.

RFAC Level Check

Connection:

5. Press the [CHECK] button actuate the focus search. (actuate

the focus search when disc table is moving in and out)

6. Check the oscilloscope waveform (S-curve) is symmetrical

between A and B. And confirm peak to peak level within 2 ± 1

Vp-p.

oscilloscope

BD board

TP (RFAC)

TP (VC)

–

S-curve waveform

symmetry

Procedure:

1. Set the test disc (PATD-012). Disc chucking operation is

complete, then press the [POWER] button to turn the power

off.

2. Connect an oscilloscope to test point TP (RFAC) and TP (VC)

on the BD board.

within 2 ± 1 Vp-p

3. Connect between test point TP (ADJ) on the MAIN board and

GND by lead wire.

4. Press the [POWER] button to turn the power on and enter the

ADJ mode, then playback the number two track automatically.

5. Confirm that oscilloscope waveform is clear and check RFAC

signal level is correct or not.

Note: • Try to measure several times to make sure than the ratio of A : B

or B : A is more than 10 : 7.

• Take sweep time as long as possible and light up the

brightness to obtain best waveform.

Checking Location: BD board

Note: A clear RFAC signal waveform means that the shape “◊” can be

RFDC Level Check

Connection:

clearly distinguished at the center of the waveform.

RFAC signal waveform

VOLT/DIV: 200 mV

TIME/DIV: 500 ns

oscilloscope

BD board

TP (RFDC)

TP (VC)

–

level: 1.35 ± 0.4 Vp-p

Checking Location: BD board

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

Ver 1.1 2001.07

E-F Balance Check

Checking Location:

Connection:

– BD BOARD (Conductor Side) –

oscilloscope

BD board

TP (TE1)

TP (VC)

–

Procedure:

1. Set the test disc (PATD-012). Disc chucking operation is

complete, then press the [POWER] button to turn the power

off.

IC150

2. Connect an oscilloscpe to test point TP (TE1) and TP (VC) on

the BD board.

3. Connect between test point TP (ADJ) on the MAIN board and

GND by lead wire.

(VC)

4. Press the [POWER] button to turn the power on and enter the

ADJ mode, then playback the number two track automatically.

5. Press the [TIME] button. (The tracking servo and the sledding

servo are turned OFF)

IC131

IC101

(FE1)

6. Check the level B of the oscilliscope waveform and the A (DC

voltage) of the center of the Traverse waveform.

Confirm the following :

(TE1)

(RFDC)

(RFAC)

A/B x 100 = less than ± 22%

Traverse Waveform

Center of

the waveform

A (DC

voltage)

level: 1.15 ± 0.5 Vp-p

7. Press the [TIME] button. (The tracking servo and sledding servo

are turned ON)

Confirm the C (DC voltage) is almost equal to the A (DC

voltage) is step 6.

Traverse Waveform

C (DC

voltage)

Tracking servo

Sled servo

OFF

Tracking servo

Sled servo

Checking Location: BD board

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

MEMO

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

SECTION 7

DIAGRAMS

• Circuit Boards Location

7-1. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

SENSOR board

BD board

Note on Schematic Diagram:

Note on Printed Wiring Board:

LOADING MOTOR board

• All capacitors are in µF unless otherwise noted. pF: µµF

• X : parts extracted from the component side.

• Y : parts extracted from the conductor side.

50 WV or less are not indicated except for electrolytics

and tantalums.

•

: Pattern from the side which enables seeing.

• All resistors are in Ω and ¹/⁴W or less unless otherwise

(The other layers' patterns are not indicated.)

KEY (A) board

JUNCTION board

specified.

•

: internal component.

Caution:

• C : panel designation.

Pattern face side: Parts on the pattern face side seen from

(Conductor Side) the pattern face are indicated.

Parts face side:

POWER SW board

Note:

Parts on the parts face side seen from

Les composants identifiés par

une marque 0 sont critiques

pour la sécurité.

Ne les remplacer que par une

pièce portant le numéro

spécifié.

The components identi-

fied by mark 0 or dotted

line with mark 0 are criti-

cal for safety.

Replace only with part

number specified.

(Component Side) the parts face are indicated.

• Indication of transistor

• A : B+ Line.

• B : B– Line.

• Voltages and waveforms are dc with respect to ground

under no-signal conditions.

no mark : CD PLAY

• Voltages are taken with aVOM (Input impedance 10 MΩ).

Voltage variations may be noted due to normal produc-

tion tolerances.

• Waveforms are taken with a oscilloscope.

Voltage variations may be noted due to normal produc-

tion tolerances.

These are omitted.

MAIN board

KEY (B) board

B E

DISPLAY board

• Circled numbers refer to waveforms.

• Signal path.

HEADPHONE board

: CD PLAY

: DIGITAL OUT

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

Ver 1.1 2001.07

7-2. PRINTED WIRING BOARD – BD Section – • See page 21 for Circuit Boards Location.

M101

(SPINDLE)

BD BOARD

(COMPONENT SIDE)

(CONDUCTOR SIDE)

TP (DGND)

S101

(LIMIT)

C154

C158

C151

R152

R151

C152

C153

R155

M102

(SLED)

C150

IC150

R153

TP (VC)

RB102

C133

RB101

C112

R110

R139

C139

C130

R141

C145

R145

R142

R144

C134

C137

R146

R184

R174

IC131

R181

R182

R111

R112

C182

C172

C181

C183

C173

R183

C103

R103

C184

Q132

R172

C136

R140

R134

IC101

C193

TP (FE1)

C171

R149

R136

CN101

C174

R173

R143

C124

C194

C138

MAIN BOARD

CN301

R102

C192

X191

C102

C101

R171

R191

C191

TP (TE1)

(Page 28)

Q131

C111

R101

FB191

C199

R135

TP (RFDC)

C120

R120

C123

R126

R137

C132

R127

C140

R192

R123

R138

C126

R125

C122

C121

C110

C125

C131

CN102

TP (RFAC)

1-681-001-

(11)

OPTICAL PICK-UP

BLOCK

(PXR-104X)

• Semiconductor

Location

Ref. No. Location

IC101

IC131

IC150

C-8

E-8

E-10

Q131

Q132

F-6

E-6

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

Ver 1.1 2001.07

7-3. SCHEMATIC DIAGRAM – BD Section – • See page 32 for Waveforms. • See page 29 for IC Block Diagrams.

TP (RFDC)

(Page 26)

The components identified by mark 0 or dotted

line with mark 0 are critical for safety.

Replace only with part number specified.

Les composants identifiés par une marque 0 sont

critiques pour la sécurité. Ne les remplacer que

par une pièce portant le numéro spécifié.

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

7-4. PRINTED WIRING BOARDS – MOTOR/SENSOR Section – • See page 21 for Circuit Boards Location.

MAIN BOARD

(Page 28)

CN311

(TABLE SENSOR)

(DISC SENSOR)

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

7-5. SCHEMATIC DIAGRAM – MOTOR/SENSOR Section – • See page 29 for IC Block Diagram.

(Page 26)

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

7-6. SCHEMATIC DIAGRAM – MAIN Section (1/2) – • See page 32 for Waveform.

(Page 23)

(Page 27)

(Page 25)

(Page 31)

Download from Www.Somanuals.com. All Manuals Search And Download.

7-7. SCHEMATIC DIAGRAM – MAIN Section (2/2) –

CDP-CE575

(Page 26)

The components identified by mark 0 or dotted

line with mark 0 are critical for safety.

Replace only with part number specified.

Les composants identifiés par une marque 0 sont

critiques pour la sécurité. Ne les remplacer que

par une pièce portant le numéro spécifié.

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

7-8. PRINTED WIRING BOARDS – MAIN Section – • See page 21 for Circuit Boards Location.

MAIN BOARD

(Page 22)

(Page 24)

BD BOARD

JUNCTION BOARD

CN11

CN101

JW20

R520

R514

C505

JW18

JW19

R509

R510

R511

R512

J301

IC502

R515

R513

Q502

C507

ANALOG

OUT

Q504

JW28

JW29

R420

JW91

Q352

C504

C551

C451

R507

R506

R551

R552

R522

R519

JW43 JW45

C619

C407

C508

R553

JW87

R453

CN301

R351

C406

JW30

JW31

JW21

R452

R451

IC351

2ND CD

JW27

R517

R521

JW34

JW88

R421

JW90 R303

JW46

JW44

JW47

JW998

JW32

R314

R315

R820

JW48

R840

JW74

C408

JW33

Q503

Q404 R415

R412

JW24

C506

JW49

R413

R419

JW89

R300

IC402

JW35

R414

R353

R417

C325

R810

R830

JW41

IC303

X301

C404

R422

Q402

JW50

R325

R411

R407

DIGITAL

OUT

OPTICAL

C405

JW51

JW52

JW53

C301

R409

Q307

R305

Q403

R410

C351

C326

Q353

R406

JW120

JW118

JW42

JW121

D352

R354

CN311

C381

JW25

Q381

Q354

R418

D353

JW37

R306

R326

JW117

C613

R307

Q355

C350

Q356

JW73

J381

R610

JW26

R620

JW54

C302

R518

CONTROL

R381

JW102

A1 II

R327

JW55

JW57

R329

R355

R382

D381

JW75

JW56

JW114

L381

JW119

JW115

JW116

JW94

L602

JW36

D608

C608

R383

JW103

C382

C303

C304

C611

(CHASSIS)

R602

CN603

JW104

JW122

JW64

JW65

JW105

Q311

R316

JW108

JW58

D606

JW106

IC302

JW62

JW63

D607

D301

C620

IC602

R311

JW66

D603

D604

T601

POWER

TRANSFORMER

R308

R310

C602

R318

C604

C603

D602

R312

C607

D601

C305

R601

R309

JW123

JW59

JW60

JW69

JW61

D605

R301

IC603

TP(AFADJ)

R317

TP(ADJ)

R302

JW112

JW111

JW68

JW107

JW110

NOT REPLACEABLE:

BUILT IN

TRANSFORMER

EB601

IC601

JW113

R612

Q601

R616

C830

C810

CN351

C609

D612

CN801

C616

R611

D610

C610

R613

JW109

(US, CND) (AEP)

C840

C820

1-681-132-

(11)

(21)

DISPLAY BOARD

CNP801

(CHASSIA)

(Page 30)

POWER SW BOARD

HEADPHONE BOARD

R881

R882

C601

J881

PHONES

CN601

JW3

C881

JW2

JW1

C883

• Semiconductor Location

(AC IN)

CN881

C882

(US, CND) (AEP)

Ref. No. Location Ref. No. Location Ref. No. Location Ref. No. Location

1-681-136-

(11)

(21)

D607

D608

D610

D612

E-6

D-5

F-7

F-8

D301

D352

D353

D381

D601

D602

D603

D604

D605

D606

E-9

C-3

D-4

D-2

E-6

F-7

E-6

IC502

IC601

IC602

IC603

A-4

F-8

E-8

F-9

Q355

Q356

Q381

Q402

Q403

Q404

Q502

Q503

Q504

Q601

D-3

D-2

C-2

B-3

C-2

B-3

F-7

S601

POWER

CN602

(US, CND) (AEP)

1-681-135-

(11)

(21)

IC301

IC302

IC303

IC351

IC402

D-9

E-9

C-1

B-9

C-4

Q307

Q311

Q352

Q353

Q354

C-8

E-9

B-3

C-3

D-4

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

• IC Block Diagrams

– BD Board –

– JUNCTION Board –

IC11 BA6780

IC101 CXD2587Q

IC131 CXA2581N-T4

RW/ROM

30 DC OFST

29 RFDCI

VIN1

FIN1

VIN2

–

28 RFDCO

ERROR

DIGITAL

OUT

CORRECTOR

DVC

ASYMMETRY

CORRECTION

FIN2

RIN2

CT2

DIGITAL

PLL

DVC

VCC

16K

RAM

OPERATIONAL

AMPLIFIER

ANALOG SWITCH

LRCK 61

D/A

INTERFACE

EFM

–

RIN1

IOUT

PCMD 62

DVC

RW/ROM

DEMODULATOR

VOFST

27 VC

A/D

BCK

CONVERTER

EMPH 64

XVDD 65

26 RFC

25 VFC

24 BST

XTAI 66

XTAO 67

TIMING

LOGIC

CLOCK

APC AMP

XTSL

TES1

TEST

GENERATOR

XVSS

AVDD1

AOUT1

AIN1

VREF

VREG

VCC

14 VEE

EQ ON/OFF

RW/ROM

SERVO DSP

PWM GENERATOR

VSS

RFAC

VCA

EQ IN

23 RFG

22 VCC

21 CEI

33 FRDR

32 FFDR

FOCUS

SERVO

FOCUS PWM

GENERATOR

FBIN-

VCC

RFAC

SUMMING

AMP

TRDR

30 TFDR

SRDR

TRACKING

PWM GENERATOR

TRACKING

SERVO

AC SUM

GND

LOUT1 72

AVSS1

VOFST

–

SUBCODE

PROCESSOR

PWM

SLED

SLED PWM

GENERATOR

FBIN+

SERVO

28 SFDR

–

AVSS2 74

20 CE

SSTP

LOUT2

3rd ORDER

NOISE SHAPER

SERVO

INTERFACE

DVC

OUT2+

OUT2-

MDP

OUT1+

OUT1-

DIGITAL

CLV

25 LOCK

OVER SAMPLING

DIGITAL FILTER

AIN2 76

RW/ROM

19 TE BAL

AOUT2 77

AVDD2 78

24 FOK

23 DFCT

22 MIRR

SERVO AUTO

SEQUENCER

MIRR, DFCT,

FOK

DETECTOR

RMUT

SERIAL IN

INTERFACE

LMUT 80

–

18 TE

CPU

INTERFACE

COUT

10 11 12 13 14 15 16 17

APC-OFF

(Hi-Z)

RW/ROM

(H/L)

RW/ROM

SW 12

DVCC 13

17 FEI

16 FE

VOFST

–

DVC

–

DVC 14

DVC

RW/ROM

RFAC 15

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

7-9. PRINTED WIRING BOARDS – DISPLAY Section – • See page 21 for Circuit Boards Location.

DISPLAY BOARD

Q805

Q804

58 59

R806

Q803

Q802

. AMS >

(DISC)

PUSH ENTER

CNP801

R801

R803

R852

C803

S811

FL801

FLUORESCENT INDICATOR TUBE

Q806

R804

JW8

R813

S814

R814

JW4

Q801

R853

JW10

CN811

JW16

R815

R802

JW15

R805

DISC

SKIP

JW11

S815

D801

EX-CHANGE

R862

C862

IC802

R807

R851

C854

S813

R812

S812

JW12

MAIN BOARD

CN801

JW9

R816

C852

C801

R823

R811

R861

R824

R822

R854

R855

(Page 28)

S801

ROTARY ENCODER

JW14

JW17

X-FADE

NO DELAY

S821

S822

S823

S824

S825

(AMS–)

(AMS+)

C861

D801, S821

MEGA CONTROL

C853

C855

JW13

1-681-133-

JW5

JW6

(US, CND) (AEP)

R821

Q807

S811-815, 821-827,

S831-838, 841-846

(11)

(21)

JW7

KEY(A) BOARD

R846

CN812

S846

OPEN/CLOSE

R831

R832

R833

R834

DISC 1

S835

CNP811

S831

S832

R826

DISC 5

DISC 4

S833

R837

DISC 3

S834

R836

DISC 2

KEY(B) BOARD

R825

S826

R835

S836

R842

R843

R844

R845

S845

R841

S841

CNP812

CONTINUE

TIME/TEXT

S827

S838

REPEAT

PROGRAM

S837

SHUFFLE

FADER

S842

S843

CLEAR

S844

CHECK

EDIT

PEAK

1-681-134-

1-681-137-

(US, CND) (AEP)

(11)

(21)

(11)

(21)

• Semiconductor

Location

Ref. No. Location

D801

B-3

IC801

IC802

A-8

B-12

Q801

Q802

Q803

Q804

Q805

Q806

Q807

A-6

A-12

B-2

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

7-10. SCHEMATIC DIAGRAM – DISPLAY Section – • See page 32 for Waveform.

(Page 26)

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

• Waveforms

– BD Board –

7-11. IC PIN FUNCTION DESCRIPTION

– MAIN Board –

•

BD BOARD IC101 CXD2587Q

(DIGITAL SIGNAL PROCESSOR, DIGITAL SERVO PROCESSOR, DIGITAL FILTER, D/A CONVERTER)

1 IC101 ta (RFAC) (CD Play Mode)

6 IC101 w; (SCOR) (CD Play Mode)

qa IC301 es (XTAL)

Pin No.

Pin Name

SQSO

I/O

Description

Subcode Q data output to the system controller (IC301)

SQCK

Subcode Q data reading clock signal input from the system controller (IC301)

System reset signal input from the system controller (IC301) “L”: reset

5.2 Vp-p

XRST

5 Vp-p

1.3 Vp-p

Analog line muting on/off control signal input terminal “H”: line muting on

Not used (fixed at “L”)

SYSM

DATA

XLAT

CLOK

SENS

SCLK

VDD

Command serial data input from the system controller (IC301)

Command latch pulse input from the system controller (IC301)

Command serial data transfer clock signal input from the system controller (IC301)

Internal status monitor output to the system controller (IC301)

SENSE serial data reading clock input from the system controller (IC301)

Power supply terminal (+5V) (digital system)

13.4 ms

100 ns

2 IC101 rd (RFDC) (CD Play Mode)

IC101 yj (XTAO) (CD Play Mode)

– DISPLAY Board –

qs IC801 t; (OSCO)

—

I/O

ATSK

SPOA

SPOB

XLON

WFCK

XUGF

XPCK

GFS

Input pin for anti-shock Not used (fixed at “L”)

Microcomputer escape interface input A terminal Not used (fixed at “L”)

Microcomputer escape interface input B terminal Not used (fixed at “L”)

Microcomputer escape interface output terminal Not used (open)

WFCK output terminal Not used (open)

5.9 Vp-p

1.4 Vp-p

I/O

2.3 Vp-p

Not used (open)

59 ns

Not used (open)

3 IC101 el (FE) (CD Play Mode)

Not used (open)

508 ns

C2PO

SCOR

COUT

MIRR

DFCT

FOK

Not used (open)

Subcode sync (S0+S1) detection signal output to the system controller (IC301)

Numbers of track counted signal input/output terminal Not used (open)

Mirror signal input/output terminal Not used (open)

Defect signal input/output terminal Not used (open)

Focus OK input/output terminal Not used (open)

approx.

200 mVp-p

LOCK

MDP

GFS is sampled by 460 Hz “H” when GFS is “H” Not used (open)

Spindle motor (M101) servo drive signal output to the AN48005B (IC150)

Limit in detect switch (S101) input terminal

SSTP

SFDR

SRDR

TFDR

TRDR

FFDR

FRDR

VSS

4 IC101 ra (TE) (CD Play Mode)

—

Sled servo drive PWM signal (+) output to the AN48005B (IC150)

Sled servo drive PWM signal (–) output to the AN48005B (IC150)

Tracking servo drive PWM signal (+) output to the AN48005B (IC150)

Tracking servo drive PWM signal (–) output to the AN48005B (IC150)

Focus servo drive PWM signal (+) output to the AN48005B (IC150)

Focus servo drive PWM signal (–) output to the AN48005B (IC150)

Ground terminal (digital system)

approx.

400 mVp-p

TEST

TES1

Input terminal for the test (fixed at “L”)

5 IC101 wh (MDP) (CD Play Mode)

Input terminal for the system clock frequency setting “L”: 45.1584 MHz, “H”: 22.5792 MHz

(fixed at “L” in this set)

XTSL

Middle point voltage (+2.5V) input from the CXA2581N (IC131)

Focus error signal input from the CXA2581N (IC131)

Sled error signal input from the CXA2581N (IC131)

2.7 V

Tracking error signal input from the CXA2581N (IC131)

Command chip enable signal input from the CXA2581N (IC131)

7.5 µs

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

Pin No.

Pin Name

RFDC

ADIO

AVSS0

IGEN

I/O

Description

RF signal input from the CXA2581N (IC131)

—

Monitor output of the A/D converter input signal Not used (open)

Ground terminal (digital system)

Stabilized current input for operational amplifiers

Power supply terminal (+5V) (digital system)

Playback EFM full-swing output terminal

AVDD0

ASYO

ASYI

—

Playback EFM asymmetry comparator voltage input terminal

Playback EFM asymmetry circuit constant current input terminal

EFM signal input from the CXA2581N (IC131)

Ground terminal (digital system)

BIAS

RFAC

AVSS3

CLTV

FILO

—

Internal VCO control voltage input of the playback master PLL

Filter output for master clock of the playback master PLL

Filter input for master clock of the playback master PLL

Phase comparison output for master clock of the playback EFM master PLL

Power supply terminal (+5V) (digital system)

Ground terminal (digital system)

FILI

PCO

—

AVDD3

VSS

VDD

Power supply terminal (+5V) (digital system)

Digital audio signal output to the DIGITAL OUT OPTICAL (IC303)

L/R sampling clock signal (44.1 kHz) output terminal Not used (open)

D/A interface serial data output terminal Not used (open)

Bit clock signal (2.8224 MHz) output terminal Not used (open)

De-emphasis control signal output terminal Not used (open)

Power supply terminal (+5V) (crystal oscillator system)

System clock input terminal (16.9344 MHz)

DOUT

LRCK

PCMD

BCK

EMPH

XVDD

XTAI

XTAO

XVSS

AVDD1

AOUT1

AIN1

—

System clock output terminal (16.9344 MHz)

Ground terminal (crystal oscillator system)

Power supply terminal (+5V) (analog system)

L-ch analog audio signal output terminal

L-ch operational amplifiers input terminal

LOUT1

AVSS1

AVSS2

LOUT2

AIN2

—

L-ch line output terminal

Ground terminal (analog system)

R-ch line output terminal

R-ch operational amplifiers input terminal

AOUT2

AVDD2

RMUT

LMUT

—

R-ch analog audio signal output terminal

Power supply terminal (+5V) (analog system)

R-ch line muting on/off control signal output terminal

L-ch line muting on/off control signal output terminal

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

• MAIN BOARD IC301 CXP84648-085Q (SYSTEM CONTROLLER)

Pin No.

1 to 4

Pin Name

A3 to A6

GND

I/O

Description

Address signal output to the static RAM (IC302)

Ground terminal

—

6 to 13

D0 to D7

I/O Two-way data bus with the static RAM (IC302)

—

Chip select signal output to the static RAM (IC302)

Not used (open)

15 to 18

Write enable signal output to the static RAM (IC302)

Loading motor (M10) drive signal output to the BA6780 (IC11)

Serial data transfer clock signal output to the FL driver (IC801)

Serial data output to the FL driver (IC801)

Reset signal output to the FL driver (IC801)

Address signal output to the static RAM (IC302)

Detect signal input from the disc sensor (D11)

Not used (open)

LOAD OUT

LOAD IN

FL CLK

FL DATA

FL RST

A13, A14, A7

DSENS

25 to 27

—

System reset signal input from the reset signal generator (IC603) “L”: reset

For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”

RST

EXTAL

XTAL

VSS

—

Main system clock input terminal (10 MHz)

Main system clock output terminal (10 MHz)

Ground terminal

Sub system clock output terminal Not used (open)

Sub system clock input terminal Not used (fixed at “L”)

Ground terminal (for A/D converter)

Reference voltage input terminal (+5V)

Not used (open)

TEX

AVSS

AVREF

—

VERSION

ADJ

Model Destination setting terminal

Setting terminal for the test mode

Key input terminal (A/D input) (S941 to S845) FADER, PEAK SEARCH, CLEAR, CHECK,

EDIT keys input

KEY4

KEY3

KEY2

KEY1

Key input terminal (A/D input) (S831 to S838) DISC 5, DISC 4, DISC 3, DISC 2, DISC 1,

CONTINUE, SHUFFLE, PROGRAM keys input

Key input terminal (A/D input) (S821 to S827) MEGA CONTROL, X-FADER NO DELAY,

MENU, m (AMS–), M (AMS+), TIME/TEXT, REPEAT keys input

Rotary encoder key input terminal (A/D input) (S801, S811 to S815) l AMS L (DISC)

PUSH ENTER, H, X, s, EX-CHANGE, DISC SKIP keys input

TSENS

FLT

—

Not used (open)

Detect signal input from the table sensor (D10)

Serial data latch pulse output to the FL driver (IC801)

Serial data transfer clock signal output to the CXD2587Q (IC101)

Not used (open)

CLK

DATA

SQCK

SQSO

Serial data output to the CXD2587Q (IC101)

Sub-code Q data reading clock signal output to the CXD2587Q (IC101)

Sub-code Q data signal input from the CXD2587Q (IC101)

Not used (open)

—

SENSE

Internal status (SENSE) signal input from the CXD2587Q (IC101)

Not used (fixed at “H”)

RMIN

Remote control signal input from the remote control receiver (IC802)

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

Pin No.

Pin Name

I/O

Description

XLT

—

Not used (fixed at “H”)

Serial data latch pulse signal output to the CXD2587Q (IC101)

Not used (open)

59, 60

SCOR

BUSIN

BUSOUT

SMUTE

LDON/RW

TBLL

TBLR

S2, S1

OUT SW

Sub-code sync (S0+S1) detection signal input from the CXD2587Q (IC101)

Sircs remote control signal input from the CONTROL A1II

Sircs remote control signal output to the CONTROL A1II

Muting on/off control signal output terminal “H” active

Laser power control signal output to the CXA2581N (IC131) “H” active

Table motor drive signal (counterclockwise) output to the BA6780 (IC11)

Table motor drive signal (clockwise) output to the BA6780 (IC11)

Detect signal input from the table address detect switch (S200)

Detect signal input from the open/close detect switch (S11)

Address signal output to the static RAM (IC302)

68, 69

—

VDD

Power supply terminal (+5V)

Not used (fixed at “H”)

A9 to A12,

A0 to A2

74 to 80

Address signal output to the static RAM (IC302)

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

SECTION 8

EXPLODED VIEWS

NOTE:

• -XX and -X mean standardized parts, so they

may have some difference from the original

one.

• Color Indication of Appearance Parts

Example:

•

Items marked “*” are not stocked since they

are seldom required for routine service. Some

delay should be anticipated when ordering

these items.

The mechanical parts with no reference num-

ber in the exploded views are not supplied.

Accessories and packing materials are given

in the last of the electrical parts list.

Abbreviation

The components identified by mark

0 or dotted line with mark 0 are

critical for safety.

Replace only with part number

specified.

•

Les composants identifiés par une

marque 0 sont critiquens pour la

sécurité.

Ne les remplacer que par une pièce

portant le numéro spécifié.

KNOB, BALANCE (WHITE) . . . (RED)

↑

Parts Color Cabinet's Color

CND : Canadian model

8-1. CASE SECTION

not supplied

Front panel section

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

4-231-683-11 PANEL, LOADING

4-210-291-01 SCREW (CASE 3 TP2)

4-231-686-11 CASE (409538)

7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

8-2. FRONT PANEL SECTION

not supplied

supplied with

headphone board J881

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

4-231-928-01 KNOB (AMS)

1-681-137-21 KEY (B) BOARD (AEP)

3-354-981-11 SPRING (SUS), RING

1-681-134-11 KEY (A) BOARD (US, CND)

1-681-134-21 KEY (A) BOARD (AEP)

4-231-973-01 BUTTON (POWER)

X-4953-512-1 PANEL ASSY, FRONT (US, CND)

X-4953-521-1 PANEL ASSY, FRONT (AEP)

A-4476-754-A DISPLAY BOARD (US, CND)

A-4476-660-A DISPLAY BOARD (AEP)

1-681-135-11 POWER SW BOARD (US, CND)

1-681-135-21 POWER SW BOARD (AEP)

4-951-620-01 SCREW (2.6X8), +BVTP

1-681-137-11 KEY (B) BOARD (US, CND)

1-757-649-11 WIRE (FLAT TYPE) (15 CORE)

1-681-136-11 HEADPHONE BOARD (US, CND)

1-681-136-21 HEADPHONE BOARD (AEP)

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

8-3. CHASSIS SECTION

CDM59-5BD27

106

T601

105

104

107

110

103

102

101

not supplied

109

102

101

not supplied

The components identified by Les composants identifiés par une

mark 0 or dotted line with marque 0 sont critiques pour la

mark 0 are critical for safety. sécurité.

Replace only with part num- Ne les remplacer que par une pièce

ber specified.

portant le numéro spécifié.

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

101

102

103

104

4-232-237-01 FOOT (DIA. 30)

X-4953-448-1 FOOT ASSY

4-943-687-01 HOLDER, BOARD

A-4725-582-A MAIN BOARD, COMPLETE (US, CND)

A-4725-593-A MAIN BOARD, COMPLETE (AEP)

109

0110

4-233-720-01 PANEL, BACK (US)

4-233-720-11 PANEL, BACK (CND)

4-233-720-21 PANEL, BACK (AEP)

1-575-651-21 CORD, POWER (AEP)

1-783-531-31 CORD, POWER (US, CND)

105

106

107

1-757-648-11 WIRE (FLAT TYPE) (21 CORE)

3-703-249-01 SCREW, S TIGHT, +PTTWH 3X6

3-703-244-21 BUSHING (2104), CORD

0T601

1-435-342-11 TRANSFORMER, POWER (US, CND)

1-435-343-11 TRANSFORMER, POWER (AEP)

7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

8-4. CD MECHANISM DECK SECTION-1

(CDM59-5BD27)

506

510

not supplied

511

509

502

506

507

508

506

502

505

503

not

supplied

504

502

511

CD MECHANISM DECK SECTION-2

503

not supplied

M11

512

501

502

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

501

502

* 503

504

1-676-245-11 SENSOR BOARD

4-218-253-31 SCREW (M2.6), +BTTP

X-4924-457-1 ROLLER ASSY

4-224-602-01 TABLE

508

509

510

511

512

4-224-615-03 GEAR (RM-B)

4-225-328-01 BELT (ROTARY)

4-224-603-01 TRAY

4-224-619-01 BRACKET (GUIDE)

A-4672-867-A MOTOR ASSY, ROTARY (TRAY)

505

4-224-617-01 GEAR (RM-E)

506

507

4-985-672-01 SCREW (+PTPWH M2.6), FLOATING

4-224-616-01 GEAR (RM-M)

M11

1-541-632-12 MOTOR, DC (TRAY)

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

8-5. CD MECHANISM DECK SECTION-2

(CDM59-5BD27)

569

551

563

551

565

562

561

560

570

566

568

not supplied

559

567

564

551

S200

558

557

not supplied

573

M10

571

not supplied

572

555

551

556

558

BU-5BD27

554

553

552

551

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

551

552

553

554

555

4-985-672-01 SCREW (+PTPWH M2.6), FLOATING

X-4952-312-1 HOLDER (BU) ASSY

4-959-996-01 SPRING (932), COMPRESSION

4-225-885-01 BELT (LOADING)

* 564

565

566

567

568

4-951-619-01 CUSHION (A)

4-224-606-01 GEAR (RV)

4-224-605-01 GEAR (U/D)

X-4952-019-2 PULLEY (A) ASSY, CHUCKING

1-471-061-11 MAGNET ASSY

4-225-844-01 GEAR (LOADING A)

556

557

558

559

560

4-224-613-01 GEAR (SHAFT)

569

570

571

572

573

4-221-688-01 PULLEY (B), CHUCKING

4-224-618-01 LEVER (LIFTER)

1-791-930-11 WIRE (FLAT TYPE) (6 CORE)

1-676-246-11 JUNCTION BOARD

1-676-244-11 LOADING MOTOR BOARD

4-218-253-31 SCREW (M2.6), +BTTP

4-224-607-01 GEAR, SWING

4-224-609-01 GEAR (LOADING C)

A-4672-879-A MOTOR ASSY, LOADING

561

562

563

4-224-608-01 COLLAR, SWING

4-224-611-01 GEAR (LOADING B)

3-016-533-01 WASHER (FR), STOPPER

M10

S200

1-541-632-12 MOTOR, DC (LOADING)

1-418-746-11 ENCODER, ROTARY

(BU, TABLE ADDRESS DETECT)

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

8-6. BASE UNIT SECTION

(BU-5BD27)

606

605

607

M101

608

604

603

M102

603

609

602

601

The components identified by Les composants identifiés par une

mark 0 or dotted line with marque 0 sont critiques pour la

mark 0 are critical for safety. sécurité.

Replace only with part num- Ne les remplacer que par une pièce

ber specified.

portant le numéro spécifié.

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

601

602

603

604

0605

4-951-620-01 SCREW (2.6X8), +BVTP

A-4725-568-A BD BOARD, COMPLETE

4-951-940-01 INSULATOR (BU)

4-917-565-01 SHAFT, SLED

1-796-033-11 OPTICAL PICK-UP (PXR-104X)

607

608

609

M101

M102

3-713-786-51 SCREW +P 2X3

4-917-567-01 GEAR (M)

4-917-564-01 GEAR (P), FLATNESS

X-4917-523-3 MOTOR ASSY (SPINDLE)

X-4917-504-1 MOTOR ASSY (SLED)

606

1-782-817-11 WIRE (FLAT TYPE) (16 CORE)

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

SECTION 9

ELECTRICAL PARTS LIST

NOTE:

•

Items marked “*” are not stocked since they

are seldom required for routine service.

Some delay should be anticipated when order-

ing these items.

SEMICONDUCTORS

In each case, u: µ, for example:

The components identified by

mark 0 or dotted line with mark

0 are critical for safety.

Replace only with part number

specified.

• Due to standardization, replacements in the

parts list may be different from the parts speci-

fied in the diagrams or the components used

on the set.

• -XX and -X mean standardized parts, so they

may have some difference from the original

one.

• RESISTORS

All resistors are in ohms.

METAL: Metal-film resistor.

METAL OXIDE: Metal oxide-film resistor.

F: nonflammable

•

Les composants identifiés par une

marque 0 sont critiquens pour la

sécurité.

Ne les remplacer que par une pièce

portant le numéro spécifié.

uA. . : µA. .

uPB. . : µPB. .

uPD. . : µPD. .

CAPACITORS

uF: µF

uPA. . : µPA. .

uPC. . : µPC. .

•

When indicating parts by reference

number, please include the board.

COILS

uH: µH

• Abbreviation

CND : Canadian model

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

A-4725-568-A BD BOARD, COMPLETE

C193

C194

C199

1-162-920-11 CERAMIC CHIP 27PF

1-162-918-11 CERAMIC CHIP 18PF

1-164-156-11 CERAMIC CHIP 0.1uF

50V

25V

*******************

< CAPACITOR >

< CONNECTOR >

C101

C102

C103

C110

C111

1-164-315-11 CERAMIC CHIP 470PF

1-164-156-11 CERAMIC CHIP 0.1uF

1-164-315-11 CERAMIC CHIP 470PF

50V

25V

50V

6.3V

25V

CN101 1-784-360-11 CONNECTOR, FFC (LIF (NON-ZIF)) 21P

CN102 1-777-937-11 CONNECTOR, FFC/FPC 16P

1-126-206-11 ELECT CHIP

100uF

20%

1-164-156-11 CERAMIC CHIP 0.1uF

< SHORT >

C112

C120

C121

C122

C123

1-164-156-11 CERAMIC CHIP 0.1uF

1-162-970-11 CERAMIC CHIP 0.01uF

1-117-863-11 CERAMIC CHIP 0.47uF

1-162-927-11 CERAMIC CHIP 100PF

25V

6.3V

50V

FB191 1-216-864-11 SHORT

< IC >

10%

IC101

IC131

IC150

8-752-386-85 IC CXD2587Q

8-752-089-74 IC CXA2581N-T4

8-759-829-14 IC AN4800SB

C124

C125

C126

C130

C131

1-162-967-11 CERAMIC CHIP 0.0033uF 10%

1-162-965-11 CERAMIC CHIP 0.0015uF 10%

1-107-826-11 CERAMIC CHIP 0.1uF

1-164-505-11 CERAMIC CHIP 2.2uF

50V

16V

10%

< TRANSISTOR >

Q131

Q132

8-729-010-08 TRANSISTOR

8-729-600-22 TRANSISTOR

MSB710-RT1

2SA1235TP-1EF

C132

C133

C134

C136

C137

1-164-505-11 CERAMIC CHIP 2.2uF

16V

1-126-607-11 ELECT CHIP

47uF

20%

10%

20%

< RESISTOR >

1-126-607-11 ELECT CHIP

47uF

1-107-826-11 CERAMIC CHIP 0.1uF

1-126-209-11 ELECT CHIP 100uF

R101

R102

R103

R110

R111

1-216-835-11 METAL CHIP

1-216-845-11 METAL CHIP

1-216-835-11 METAL CHIP

1-216-821-11 METAL CHIP

1-216-809-11 METAL CHIP

15K

100K

15K

1/16W

C138

C139

C140

C145

C150

1-162-964-11 CERAMIC CHIP 0.001uF 10%

50V

16V

1-162-921-11 CERAMIC CHIP 33PF

1-164-505-11 CERAMIC CHIP 2.2uF

1-162-908-11 CERAMIC CHIP 3PF

100

0.25PF 50V

R112

R120

R121

R122

R123

1-216-833-11 METAL CHIP

1-216-839-11 METAL CHIP

1-216-833-11 METAL CHIP

1-216-845-11 METAL CHIP

1-216-857-11 METAL CHIP

10K

33K

10K

100K

1/16W

1-126-204-11 ELECT CHIP

47uF

20%

16V

C151

C152

C153

C154

C158

1-164-156-11 CERAMIC CHIP 0.1uF

1-162-919-11 CERAMIC CHIP 22PF

1-162-964-11 CERAMIC CHIP 0.001uF 10%

1-164-172-11 CERAMIC CHIP 0.0056uF 10%

25V

50V

25V

R125

R126

R127

R129

R134

1-216-827-11 METAL CHIP

1-216-833-11 METAL CHIP

1-216-821-11 METAL CHIP

1-216-815-11 METAL CHIP

1-216-853-11 METAL CHIP

3.3K

10K

330

470K

1/16W

C171

C172

C173

C174

C181

1-126-206-11 ELECT CHIP

100uF

20%

6.3V

25V

50V

25V

6.3V

1-164-156-11 CERAMIC CHIP 0.1uF

1-162-928-11 CERAMIC CHIP 120PF

1-115-412-11 CERAMIC CHIP 680PF

20%

R135

R136

R137

R138

R139

1-216-836-11 METAL CHIP

1-216-797-11 METAL CHIP

1-216-798-11 RES-CHIP

1-216-847-11 METAL CHIP

18K

150K

1/16W

1-126-206-11 ELECT CHIP

100uF

C182

C183

C184

C191

C192

1-164-156-11 CERAMIC CHIP 0.1uF

1-162-928-11 CERAMIC CHIP 120PF

1-115-412-11 CERAMIC CHIP 680PF

25V

50V

25V

6.3V

25V

20%

1-126-205-11 ELECT CHIP

47uF

R140

R141

1-216-854-11 METAL CHIP

1-216-840-11 METAL CHIP

560K

39K

1/16W

1-164-156-11 CERAMIC CHIP 0.1uF

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

BD DISPLAY

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

< FLUORESCENT INDICATOR TUBE >

Remark

R142

R143

R144

1-216-841-11 METAL CHIP

1-216-855-11 METAL CHIP

1-216-846-11 METAL CHIP

47K

680K

120K

1/16W

FL801 1-518-738-11 INDICATOR TUBE, FLUORESCENT

< IC >

R145

R146

R149

R151

R152

1-216-830-11 METAL CHIP

1-216-845-11 METAL CHIP

1-216-821-11 METAL CHIP

1-216-845-11 METAL CHIP

1-216-833-11 METAL CHIP

5.6K

100K

10K

1/16W

IC801

IC802

8-759-829-13 IC MSM9202-06GS-BK

8-759-827-70 IC NJL64H400A-1

< TRANSISTOR >

R153

R155

R171

R172

R173

1-216-864-11 SHORT

1-216-836-11 METAL CHIP

1-218-720-11 METAL CHIP

18K

15K

1/16W

Q801

Q802

Q803

Q804

Q805

8-729-029-66 TRANSISTOR

DTC114ESA-TP

0.5% 1/16W

DTC114ESA-TP

R174

R181

R182

R183

R184

1-216-809-11 METAL CHIP

1-218-720-11 METAL CHIP

1-216-809-11 METAL CHIP

100

15K

100

1/16W

0.5% 1/16W

Q806

Q807

8-729-029-66 TRANSISTOR

DTC114ESA-TP

1/16W

< RESISTOR >

R191

R192

1-216-817-11 METAL CHIP

1-216-797-11 METAL CHIP

470

1/16W

R801

R802

R803

R804

R805

1-249-441-11 CARBON

100K

1/4W

< COMPOSITION CIRCUIT BLOCK >

RB101 1-233-576-11 RES, CHIP NETWORK 100

RB102 1-233-576-11 RES, CHIP NETWORK 100

R806

R807

R811

R812

R813

1-249-441-11 CARBON

1-247-807-31 CARBON

1-249-415-11 CARBON

1-249-417-11 CARBON

1-249-419-11 CARBON

100K

100

680

1/4W

< SWITCH >

S101

X191

1-572-085-11 SWITCH, LEAF (LIMIT)

< VIBRATOR >

1.5K

R814

R815

R816

R821

R822

1-249-421-11 CARBON

1-247-843-11 CARBON

1-249-427-11 CARBON

1-249-415-11 CARBON

1-249-417-11 CARBON

2.2K

3.3K

6.8K

680

1/4W

1-767-408-21 VIBRATOR, CRYSTAL (16MHz)

**************************************************************

A-4476-754-A DISPLAY BOARD (US, CND)

A-4476-660-A DISPLAY BOARD (AEP)

**************

R823

R824

R846

R851

R852

1-249-419-11 CARBON

1-249-421-11 CARBON

1-249-427-11 CARBON

1-247-843-11 CARBON

1-247-807-31 CARBON

1.5K

2.2K

6.8K

3.3K

100

1/4W

2-389-320-01 CUSHION

4-997-495-01 GUIDE (FL)

< CAPACITOR >

R853

R854

R855

R861

R862

1-247-807-31 CARBON

100

1/4W

C801

C802

C803

C851

C852

1-161-494-00 CERAMIC

1-164-159-11 CERAMIC

1-104-665-11 ELECT

1-162-215-31 CERAMIC

1-161-494-00 CERAMIC

0.022uF

0.1uF

100uF

47PF

25V

50V

10V

50V

25V

20%

0.022uF

< SWITCH >

C853

C854

C855

C861

1-162-282-31 CERAMIC

1-104-665-11 ELECT

100PF

100uF

10%

20%

50V

10V

S801

1-475-543-11 ENCODER, ROTARY

(l AMS L (DISC), PUSH ENTER)

1-771-349-21 SWITCH, KEYBOARD (H)

1-771-349-21 SWITCH, KEYBOARD (X)

1-771-349-21 SWITCH, KEYBOARD (s)

1-771-349-21 SWITCH, KEYBOARD (EX-CHANGE)

S811

S812

S813

S814

< CONNECTOR >

CN811 1-750-185-11 CONNECTOR, BOARD TO BOARD 4P

CNP801 1-784-776-11 CONNECTOR, FFC 15P

S815

S821

S822

S823

S824

1-771-349-21 SWITCH, KEYBOARD (DISC SKIP)

1-771-349-21 SWITCH, KEYBOARD (MEGA CONTROL)

1-771-349-21 SWITCH, KEYBOARD (X-FADE, NO DELAY)

1-771-349-21 SWITCH, KEYBOARD (MENU)

< LED >

1-771-349-21 SWITCH, KEYBOARD (m, (AMS –))

D801

8-719-046-36 LED SEL5921A-TP15 (MEGA CONTROL)

S825

1-771-349-21 SWITCH, KEYBOARD (M, (AMS +))

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

DISPLAY HEADPHONE JUNCTION KEY (A) KEY (B)

LOADING MOTOR MAIN

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

S846

1-771-349-21 SWITCH, KEYBOARD (A OPEN/COLSE)

R826

R831

R832

R833

1-249-427-11 CARBON

1-249-415-11 CARBON

1-249-417-11 CARBON

1-249-419-11 CARBON

6.8K

680

1/4W

**************************************************************

1-681-136-11 HEADPHONE BOARD (US, CND)

1-681-136-21 HEADPHONE BOARD (AEP)

*****************

1.5K

R834

R835

R836

R837

1-249-421-11 CARBON

1-247-843-11 CARBON

1-249-427-11 CARBON

1-249-431-11 CARBON

2.2K

3.3K

6.8K

15K

1/4W

< CAPACITOR >

C881

C882

C883

1-162-294-31 CERAMIC

1-164-159-11 CERAMIC

0.001uF 10%

0.1uF

50V

< SWITCH >

S826

S827

S831

S832

S833

1-771-349-21 SWITCH, KEYBOARD (TIME/TEXT)

1-771-349-21 SWITCH, KEYBOARD (REPEAT)

1-771-349-21 SWITCH, KEYBOARD (DISC 5)

1-771-349-21 SWITCH, KEYBOARD (DISC 4)

1-771-349-21 SWITCH, KEYBOARD (DISC 3)

< JACK >

J881

1-770-307-11 JACK (LARGE TYPE) (PHONES)

< RESISTOR >

S834

S835

S836

S837

S838

1-771-349-21 SWITCH, KEYBOARD (DISC 2)

1-771-349-21 SWITCH, KEYBOARD (DISC 1)

1-771-349-21 SWITCH, KEYBOARD (CONTINUE)

1-771-349-21 SWITCH, KEYBOARD (SHUFFLE)

1-771-349-21 SWITCH, KEYBOARD (PROGRAM)

R881

R882

1-249-401-11 CARBON

1/4W

**************************************************************

1-676-246-11 JUNCTION BOARD

**************************************************************

***************

1-681-137-11 KEY (B) BOARD (US, CND)

1-681-137-21 KEY (B) BOARD (AEP)

*************

< CAPACITOR >

C10

C11

1-124-589-11 ELECT

1-161-494-00 CERAMIC

47uF

0.022uF

20%

16V

25V

< RESISTOR >

< CONNECTOR >

R841

R842

R843

R844

R845

1-249-415-11 CARBON

1-249-417-11 CARBON

1-249-419-11 CARBON

1-249-421-11 CARBON

1-247-843-11 CARBON

680

1.5K

2.2K

3.3K

1/4W

CN11

CN13

* CN14

CN15

1-573-911-11 PIN, CONNECTOR 13P

1-506-481-11 PIN, CONNECTOR 2P

1-568-941-11 PIN, CONNECTOR 3P

1-784-767-11 CONNECTOR, FFC 6P

< SWITCH >

< IC >

8-759-356-03 IC BA6780

< RESISTOR >

S841

S842

S843

S844

S845

1-771-349-21 SWITCH, KEYBOARD (FADER)

1-771-349-21 SWITCH, KEYBOARD (PEAK SEARCH)

1-771-349-21 SWITCH, KEYBOARD (CLEAR)

1-771-349-21 SWITCH, KEYBOARD (CHECK)

1-771-349-21 SWITCH, KEYBOARD (EDIT)

IC11

R21

R22

R23

R24

R25

1-249-429-11 CARBON

1-249-426-11 CARBON

1-249-425-11 CARBON

1-249-430-11 CARBON

1-249-382-11 CARBON

10K

5.6K

4.7K

12K

1.2

1/4W

1/6W

**************************************************************

1-676-244-11 LOADING MOTOR BOARD

*********************

**************************************************************

R26

1-249-382-11 CARBON

1.2

1/6W

A-4725-582-A MAIN BOARD, COMPLETE (US, CND)

A-4725-593-A MAIN BOARD, COMPLETE (AEP)

*********************

< SWITCH >

S11

1-771-836-11 SWITCH, LEVER (SLIDE)

(OPEN/CLOSE DETECT)

7-685-871-01 SCREW +BVTT 3X6 (S)

< CAPACITOR >

**************************************************************

1-681-134-11 KEY (A) BOARD (US, CND)

1-681-134-21 KEY (A) BOARD (AEP)

*************

C301

C302

C303

C304

C305

1-164-159-11 CERAMIC

1-104-665-11 ELECT

1-161-494-00 CERAMIC

0.1uF

100uF

0.022uF

50V

10V

25V

5.5V

20%

< CONNECTOR >

CNP811 1-750-194-11 CONNECTOR, BOARD TO BOARD 4P

< RESISTOR >

1-110-489-11 DOUBLE LAYER 1F

C325

C326

C350

C351

1-161-494-00 CERAMIC

1-104-665-11 ELECT

1-126-962-11 ELECT

1-126-963-11 ELECT

0.022uF

25V

10V

50V

100uF

3.3uF

4.7uF

20%

R825

1-247-843-11 CARBON

3.3K

1/4W

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

MAIN

Ref. No.

C381

Part No.

Description

Remark

50V

Ref. No.

Part No.

Description

< IC >

Remark

1-164-159-11 CERAMIC

0.1uF

C382

C404

C405

C406

C407

1-164-159-11 CERAMIC

1-126-965-11 ELECT

1-104-664-11 ELECT

1-126-933-11 ELECT

1-162-290-31 CERAMIC

0.1uF

22uF

47uF

100uF

470PF

50V

10V

16V

50V

8-752-919-06 IC CXP84648-085Q

8-759-825-10 IC BS62LV256SC-70 (T)

8-749-921-12 IC GP1F32T (DIGITAL OUT OPTICAL)

8-759-167-88 IC NJM4565D

8-749-015-59 IC BA4558-HT

20%

10%

C408

C451

C504

C505

C506

1-107-715-11 ELECT

1-126-933-11 ELECT

1-126-965-11 ELECT

1-104-664-11 ELECT

1-126-933-11 ELECT

22uF

100uF

22uF

47uF

20%

25V

16V

50V

10V

16V

8-749-015-59 IC BA4558-HT

8-759-039-69 IC uPC7805AHF

8-749-011-78 IC BA17807T

8-759-165-82 IC PST600E-T

100uF

< JACK >

C507

C508

C551

C602

C603

1-162-290-31 CERAMIC

1-107-715-11 ELECT

1-126-933-11 ELECT

1-126-937-11 ELECT

1-126-767-11 ELECT

470PF

22uF

100uF

4700uF

1000uF

10%

20%

50V

25V

16V

J301

J381

1-784-429-11 JACK, PIN 4P (ANALOG OUT, 2ND CD IN)

1-779-655-21 JACK (SMALL TYPE) (2 GANG)

(CONTROL A1 II)

< COIL >

C604

C607

C608

C609

C610

1-104-664-11 ELECT

1-126-935-11 ELECT

1-126-934-11 ELECT

1-128-552-51 ELECT

1-126-964-11 ELECT

47uF

20%

10V

6.3V

10V

63V

50V

470uF

220uF

47uF

L381

L602

1-410-503-11 INDUCTOR

1-414-151-21 INDUCTOR

3.3uH

470uH

10uF

< TRANSISTOR >

C611

C613

C616

C619

0C620

1-126-767-11 ELECT

1-126-935-11 ELECT

1-161-494-00 CERAMIC

1-104-665-11 ELECT

1-113-924-11 CERAMIC

1000uF

470uF

0.022uF

100uF

20%

16V

6.3V

25V

10V

250V

Q307

Q311

Q352

Q353

Q354

8-729-029-56 TRANSISTOR

8-729-029-66 TRANSISTOR

8-729-029-56 TRANSISTOR

DTA144ESA-TP

DTC114ESA-TP

DTA144ESA-TP

20%

0.0047uF 20%

C810

C820

C830

C840

1-161-494-00 CERAMIC

0.022uF

25V

Q355

Q356

Q381

Q402

Q403

8-729-029-56 TRANSISTOR

8-729-119-78 TRANSISTOR

8-729-141-26 TRANSISTOR

DTA144ESA-TP

2SC1740S-QRT

2SC3622ATP-LK

< CONNECTOR >

Q404

Q502

Q503

Q504

Q601

8-729-141-26 TRANSISTOR

8-729-140-97 TRANSISTOR

2SC3622ATP-LK

2SB734-T-34

CN301 1-568-838-11 CONNECTOR, FFC 21P

CN311 1-573-911-11 PIN, CONNECTOR 13P

CN351 1-506-468-11 PIN, CONNECTOR 3P

CN603 1-792-131-11 LEAD (WITH CONNECTOR)

CN801 1-784-776-11 CONNECTOR, FFC 15P

< RESISTOR >

< DIODE >

R300

R301

R302

R303

R306

1-249-427-11 CARBON

1-249-415-11 CARBON

1-249-417-11 CARBON

1-249-429-11 CARBON

6.8K

680

10K

1/4W

D301

D352

D353

D381

D601

8-719-911-19 DIODE 1SS133T-72

8-719-024-99 DIODE 11ES2-NTA2B

R307

R308

R309

R310

R311

1-249-429-11 CARBON

10K

1/4W

D602

D603

D604

D605

D606

8-719-024-99 DIODE 11ES2-NTA2B

8-719-911-19 DIODE 1SS133T-72

R312

R314

R315

R316

R317

1-249-429-11 CARBON

1-247-807-31 CARBON

1-249-429-11 CARBON

10K

100

10K

1/4W

D607

D608

D610

D612

8-719-911-19 DIODE 1SS133T-72

8-719-109-85 DIODE MTZJ-T-72-5.1B

8-719-983-99 DIODE MTZJ-T-72-39D

8-719-110-08 DIODE MTZJ-T-72-8.2B

< GROUND TERMINAL >

R318

R324

R325

R326

R327

1-249-399-11 CARBON

1-249-429-11 CARBON

1-247-807-31 CARBON

1-249-425-11 CARBON

1/4W

10K

100

4.7K

EB601 1-537-770-21 TERMINAL BOARD, GROUND

The components identified by Les composants identifiés par une

mark 0 or dotted line with marque 0 sont critiques pour la

mark 0 are critical for safety. sécurité.

Replace only with part num- Ne les remplacer que par une pièce

ber specified.

portant le numéro spécifié.

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

MAIN POWER SW SENSOR

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

R329

R350

R351

R352

R353

1-249-425-11 CARBON

1-247-807-31 CARBON

1-249-441-11 CARBON

4.7K

100

100K

1/4W

< POWER TRANSFORMER >

0T601

1-435-342-11 TRANSFORMER, POWER (US, CND)

1-435-343-11 TRANSFORMER, POWER (AEP)

< VIBRATOR >

R354

R355

R356

R381

R382

1-249-441-11 CARBON

1-249-425-11 CARBON

1-249-429-11 CARBON

100K

4.7K

10K

1/4W

X301

1-579-175-11 VIBRATOR, CERAMIC (10MHz)

**************************************************************

1-681-135-11 POWER SW BOARD (US, CND)

1-681-135-21 POWER SW BOARD (AEP)

****************

R383

R406

R407

R409

R410

1-249-393-11 CARBON

1-247-895-00 CARBON

1-249-425-11 CARBON

1-249-419-11 CARBON

1-249-429-11 CARBON

1/4W

470K

4.7K

1.5K

10K

< CAPACITOR >

0C601

1-113-924-11 CERAMIC

< CONNECTOR >

0.0047uF 20%

250V

R411

R412

R413

R414

R415

1-249-429-11 CARBON

1-247-887-00 CARBON

1-249-409-11 CARBON

10K

220K

220

1/4W

* CN601 1-580-230-31 PIN, CONNECTOR (PC BOARD) 2P

* CN602 1-568-226-11 PIN, CONNECTOR 2P

< SWITCH >

R417

R418

R419

R420

R421

1-249-427-11 CARBON

1-249-421-11 CARBON

1-249-409-11 CARBON

1-247-895-00 CARBON

6.8K

2.2K

220

1/4W

0S601

1-762-581-11 SWITCH, AC POWER PUSH (1 KEY)

(POWER)

**************************************************************

470K

1-676-245-11 SENSOR BOARD

R422

R451

R452

R506

R507

1-249-421-11 CARBON

1-247-843-11 CARBON

1-249-429-11 CARBON

1-247-895-00 CARBON

1-249-425-11 CARBON

2.2K

3.3K

10K

470K

4.7K

1/4W

*************

< CONNECTOR >

CN10

1-750-243-11 SOCKET, CONNECTOR 6P

< PHOTO INTERRUPTER >

R509

R510

R511

R512

R513

1-249-419-11 CARBON

1-249-429-11 CARBON

1-247-887-00 CARBON

1.5K

10K

220K

1/4W

D10

D11

8-749-924-18 PHOTO INTERRUPTER RPI-1391

8-749-017-45 SENSOR, PHOTO RPR-220C1N

< RESISTOR >

R514

R515

R517

R518

R519

1-249-409-11 CARBON

1-249-427-11 CARBON

1-249-421-11 CARBON

220

6.8K

2.2K

1/4W

R10

R11

R12

1-249-416-11 CARBON

1-249-407-11 CARBON

1-249-429-11 CARBON

820

150

10K

1/4W

**************************************************************

R520

R521

R522

R551

R552

1-249-409-11 CARBON

1-247-895-00 CARBON

1-249-421-11 CARBON

1-247-843-11 CARBON

1-249-429-11 CARBON

220

1/4W

MISCELLANEOUS

**************

470K

2.2K

3.3K

10K

105

0110

1-757-649-11 WIRE (FLAT TYPE) (15 CORE)

1-757-648-11 WIRE (FLAT TYPE) (21 CORE)

1-575-651-21 CORD, POWER (AEP)

R601

R602

R611

R612

R613

1-249-425-11 CARBON

1-249-411-11 CARBON

1-247-843-11 CARBON

1-247-807-31 CARBON

4.7K

330

3.3K

100

1/4W

1-783-531-31 CORD, POWER (US, CND)

512

568

571

573

0605

A-4672-867-A MOTOR ASSY, ROTARY (TRAY)

1-471-061-11 MAGNET ASSY

1-791-930-11 WIRE (FLAT TYPE) (6 CORE)

A-4672-879-A MOTOR ASSY, LOADING

1-796-033-11 OPTICAL PICK-UP (PXR-104X)

R616

R810

R820

R830

R840

1-249-429-11 CARBON

1-249-427-11 CARBON

10K

1/4W

6.8K

606

1-782-817-11 WIRE (FLAT TYPE) (16 CORE)

1-541-632-12 MOTOR, DC (LOADING)

X-4917-523-3 MOTOR ASSY (SPINDLE)

X-4917-504-1 MOTOR ASSY (SLED)

1-541-632-12 MOTOR, DC (TRAY)

M10

M101

M102

M11

The components identified by Les composants identifiés par une

mark 0 or dotted line with marque 0 sont critiques pour la

mark 0 are critical for safety. sécurité.

Replace only with part num- Ne les remplacer que par une pièce

ber specified.

portant le numéro spécifié.

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

Ref. No.

S200

Part No.

1-418-746-11 ENCODER, ROTARY

(BU, TABLE ADDRESS DETECT)

1-435-342-11 TRANSFORMER, POWER (US, CND)

1-435-343-11 TRANSFORMER, POWER (AEP)

Description

Remark

Ref. No.

Part No.

Description

Remark

0T601

************************************************************

ACCESSORIES & PACKING MATERIALS

*******************************

1-418-858-11 REMOTE COMMANDER (RM-DC545)

1-558-271-11 CORD, CONNECTION (RCA PIN PLUG)

1-777-241-11 CORD, CONNECTION (MINI PLUG) (CND)

4-233-301-11 MANUAL, INSTRUCTION (ENGLISH) (US)

4-233-301-21 MANUAL, INSTRUCTION (ENGLISH, FRENCH)

(CND)

4-233-301-31 MANUAL, INSTRUCTION (ENGLISH, FRENCH,

GERMAN, SPANISH, DUTCH, SWEDISH,

ITALIAN , PORTUGUESE) (AEP)

4-981-643-01 COVER, BATTERY (for RM-DC545)

The components identified by Les composants identifiés par une

mark 0 or dotted line with marque 0 sont critiques pour la

mark 0 are critical for safety. sécurité.

Replace only with part num- Ne les remplacer que par une pièce

ber specified.

portant le numéro spécifié.

Download from Www.Somanuals.com. All Manuals Search And Download.

CDP-CE575

REVISION HISTORY

Clicking the version allows you to jump to the revised page.

Also, clicking the version at the upper right on the revised page allows you to jump to the next revised

page.

Ver.

1.1

Date

Description of Revision

Addition of electrical adjustments

2001.07

2001.03

1.0

New

Download from Www.Somanuals.com. All Manuals Search And Download.

Sharp All in One Printer JW 20FL5 User Manual
Sony Carrying Case LCR PC User Manual
Sony Cassette Player TC TX373 User Manual
Sony Clock Radio C707 User Manual
Sony Stereo System CDX 555RF User Manual
Sony Video Game Console SCPH 75002 User Manual
SPX Cooling Technologies Humidifier MCR3100 User Manual
Stanley Black Decker Chainsaw CS05 User Manual
StarTechcom Network Card NETRS232 User Manual
SVAT Electronics Security Camera Q1204 User Manual