Snapper Lawn Mower 1687262 User Manual

Tube and Latch Kit  
Part No. 1687262  
Installation  
For 38” Regent Series Twin Catchers  
Instructions  
Ref. Part No. Qty. Description  
Ref. Part No. Qty. Description  
Kit Contents:  
10 1919326  
11 1731420  
12 1931338  
13 1720452  
1
1
5
2
Lockwasher,  
5/16  
Label, ID,  
14 1960686  
6
Nut, Nyloc,  
5/16-18  
Ref. Part No. Qty. Description  
1
2
3
1732735A  
1732799  
1960404  
1
1
6
Seal Plate  
Seal  
Screw, Phillips,  
#10-24 x 3/4  
Nut, Nylock,  
#10-24  
15 1733432A  
16 1930591  
1
1
Brace  
1695163  
Capscrew,  
5-16 x 3/4  
Latch  
Carriage Bolts,  
5/16-18 x 1-3/4  
Saddle Clamp  
17 1733416A  
1
4
1933896  
6
5
6
7
8
9
1703769  
1704603  
1960185  
1935048  
1960122  
1
1
1
1
1
Tube  
Latch, Tube  
Washer, Flat  
Nut, 5/16-18  
Capscrew,  
5/16-18 x 3/4  
5
4
15  
12  
9
10  
16  
3
7
1
11  
2
17  
6
14  
8
13  
Figure 1. Contents  
This kit is for updating a 1694916 Twin Catcher to  
a 1695163 Twin Catcher.  
A
WARNING  
Before beginning any service work turn off the  
PTO, set the parking brake, turn off the ignition,  
and disconnect the spark plug wire(s).  
B
Note: Use these Instructions to supplement portions of  
the Operator’s Manual for Twin Catcher 1694916. Keep  
these Instructions for future reference.  
INSTALLATION  
1. Apply new ID Label (A, Figure 2) directly over exist-  
ing product ID Label on channel assembly (B).  
Figure 2. Apply New ID Label  
A. ID Label, 1695163, (New)  
B. Channel Assembly  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
Tube and Latch Kit  
Installation Instructions  
Drill 11/32”  
Hole Here  
C
A
B
A
2“  
B
D
C
Figure 5. Drill Hole In Boot  
A. New 11/32” Hole  
B. Existing Hole  
C. Boot  
Figure 7. Remove Latch  
A. Cover Assembly  
B. Latch  
C. Locknuts, Nylock, #10-24  
D. Screws, #10-24 x 5/8  
B
C
C
D
A
A
B
Figure 6. Install Puck to Boot  
A. Boot  
B. Puck, Metal  
D
C. Capscrew, Thin Head, 5/16-18 x 3/4  
D. Locknuts 5/16-18  
4. Drill a new 11/32 hole (A, Figure 5) 2” from the exist-  
ing hole (B) in boot (C) as shown.  
5. Secure the puck (B, Figure 6) to boot (A) using 5/16-  
18 x 3/4 capscrew (C) and 5/16-18 locknut (D).  
Figure 8. Install Latch  
A. Cover Assembly  
B. Latch (New)  
C. Locknuts, ESNA, #10-24 (Existing)  
D. Screws, #10-24 x 5/8 (Existing)  
6. Remove and discard the latch (B, Figure 7) from the  
cover assembly (A). Remove and retain #10-24 x 5/8  
screws (D) and #10-24 locknuts (C).  
7. Install the new latch (B, Figure 8) to the cover assem-  
bly (A) securing with Existing #10-24 x 5/8 screws (D)  
and #10-24 locknuts (C) as shown.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation Instructions  
Tube and Latch Kit  
C
E
C
H
C
G
F
C
D
D
A
G
B
D
F
Figure 10. Install Tube in Cover  
B
A. Tube  
B. Seal  
C. Slits  
A
D
Figure 9. Install “U” Tube  
A. “U” Tube  
B. Channel Assembly  
C. Carriage Bolts, 5/16-18 X 1-3/4  
D. Nuts, Nyloc, 5/16-18  
E. “L” Channel  
B
C
F. Saddle Brackets  
G. New 11/32 Holes  
D
H. Capscrew, 5/16-18 x 3/4  
8. Install the “U” tube (A, Figure 9) and “L” channel (F)  
to channel assembly (B) securing with 5/16-18 x 3/4  
carriage bolts (C) and 5/16-24 nuts (E).  
9. Using the “L” channel as a guide drill two 11/32 holes  
(G) in “U” tube (A) as shown. Install 5/16-18 x 1-3/4  
carriage bolts (C) through new holes (G) and secure  
with saddle clamps (F) and 5/16-18 locknuts (D) and  
5/16-18 nuts (E).  
A
Figure 11. Install Discharge Tube to Boot  
A. Boot  
B. Discharge Tube  
C. Metal Puck  
10. Install 5/16-18 x 3/4 capscrew (H) and 5/16-18 lock-  
nut (D) as shown.  
Connect Tube to Cover and Boot  
D. Wire Form  
1. Slide discharge tube (A, Figure 10) into seal (B). It  
may be necessary to lengthen several slits (C) in  
order for tube (A) to fit into seal (B)  
3. Attach the discharge tube (B, Figure 11) to boot (A)  
and secure the tube by moving wire form (D) down  
over metal puck (C).  
2. Install boot according to Operator’s Manual.  
4. Reverse connection to remove discharge tube.  
MANUFACTURING, INC.  
Form No. 1733418-01  
Rev. 5/2006  
4
500 N Spring Street / PO Box 997  
Port Washington, WI 53074-0997 USA  
© 2006 Simplicity Manufacturing, Inc. All Rights Reserved  
TP 200-4298-01-SK-SMA  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Sennheiser Microphone K 30 AV User Manual
Shure Battery Charger SBC210 User Manual
Shure Headphones 515SBGX User Manual
Shure Microphone SM94 User Manual
Snapper Lawn Aerator 4545 User Manual
Sony Camcorder CCD TR57 User Manual
Sony Personal Computer PCV RX270DS User Manual
SoundMax TV Receiver SM CMD3005 User Manual
Stiga Lawn Mower 13 6133 36 User Manual
SysKonnect Network Card SK 98xx V20 User Manual