6
DVD PLAYER
KH 6523
DVD Player
Operating instructions
KOMPERNASS GMBH · BURGSTRASSE 21 · D-44867 BOCHUM
ID-Nr.: KH6523 - 11/09-V2
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
PAGE
1. Technical Data
2
2
2
2
3
3
4
2. Intended use
3. Package contents
4. Operating components
5. Setting up of the DVD player
6. Safety instructions
7. Remote control
7.1 Inserting the batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
7.2 Using the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
7.3 Replacing the batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
8. Connecting the DVD player to a television
4
8.1 Connecting to a television via ScartCable/RGB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
8.2 Connecting to a television via S-Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
8.3 Connection to a television via video input (Composite Video) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
8.4 Connecting via component signal (YPbPr/YUV) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
8.5 Connecting to a television via HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
9. Connecting audio components to the DVD player
6
9.1 Requirements for the connection of a HiFi system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
9.2 Connecting digital audio components via digital cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
9.3 Connecting audio components via an analogue cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
9.4 Connecting the headphones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
10. OSD menu settings
8
10.1 Using the OSD Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
10.2 Setup menu GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
10.3 Setup menu AUDIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
10.4 Setup menu DOLBY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
10.5 Setup menu VIDEO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
10.6 Setup menu PREFERENCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
11. Initial operation of the DVD player
12
11.1 Switching the DVD player on/off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
11.2 Inserting the DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
12. Playing back DVDs, VCDs or S-VCDs
12
12.1 Features during playback of a DVD, VCD or S-VCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
13. Playback of JPEG-Photo CD/WMA/MP3/MPEG4
14. Cleaning of the DVD player
15. Disposal
17
18
18
18
19
21
21
16. Troubleshooting
17. Glossary / Key Word Index
18. Warranty and Service
19. Importer
Read these operating instructions carefully before using the device for the first time and preserve this manual for later reference.
Pass this manual on to whoever might acquire the device at a future date.
- 1 -
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD PLAYER KH6523
2. Intended use
This documentation is copyright protected.
The Silvercrest KH 6523 DVD player is exclusively intended for the playback
of CDs and DVDs in a closed room residential environment. The device is
intended exclusively for private, non-commercial use.
The device is intended for use as a home entertainment device.
No liability/warranty will be accepted for damages that result from improper
use of the device or from unauthorised reconstruction!
Any duplication and/or reproduction, wholly or partially including extracts as
well as the reproducing of illustrations also in modified form is only permitted
with written agreement from the manufacturer.
1. Technical Data
This device conforms regarding compliance to the basic requirements and
other relevent provisions of the low-voltage directive 2006/96/EC, the
EMV directive 2004/108/EC as well as the Ecological design directive
2009/125/EC (Ordinance 1275/2008) Supplement II, Number 1).
3. Package contents
-
-
-
-
-
-
DVD Player
Infrared remote control
2 Batteries for remote control, type AAA/ (Micro cells)
RGB Scart cable
HDMI cable
Operating manual
Power supply:
Power consumption:
Power consumption:
Standby:
Protection class:
TV standard:
AC 220 V - 240 V 50 Hz
~
20 Watt
< 1 W
II /
PAL/NTSC
4. Operating components
Operating temperature:
Humidity:
Measurements
(L x W x H):
+5 +40°C
~
5
90% (no condensation)
~
A. DVD player front panel
220 x 430 x 45 mm
Disc tray
q
w
e
r
t
y
u
Weight :
Laser class:
1,6 kg approx.
1
Display (with standby LED (green) and IR sensor for remote control)
OPEN/CLOSE
PLAY/PAUSE ꢀꢁbutton
STOP ꢂ button
button
Video Output
Format:
Decoder:
4:3 / 16:9
MPEG 2
12 Bit
STANDBY
button
Headphones output for 3,5 mm jackplug
D/A converter:
B. DVD player rear panel
Audio Output
Decoder:
Power cable
i
o
a
s
d
f
g
h
j
k
l
;
2)
2!
MPEG Dolby Digital (AC-3)
DTS only possible with additional external decoder
24 Bit / 96 kHz
POWER switch
VIDEO: Composite video output
Y, Pb/Cb, Pr/Cr: Component video outputs
SCART: Scart/RGB output
FL/FR: Output for front, left and right audio channels
SL/SR: Output for rear, left and right audio channels
SW: Output for bass audio channel
CEN: Output for centre audio channel
COAXIAL: Coaxial audio output
AUDIO L/R: Left and right audio outputs
HDMI: HDMI output
D/A converter:
Headphones output
Jackplug:
Maximum
3,5 mm
output voltage:
approx. 25 mV
Playable mediums/formats
VIDEO:
DVD, DVD+R, DVD+RW, DVD-R, DVD-RW,
DVD-R DL, DVD+R DL, VCD, S-VCD
CD, CD-R, CD-RW, Audio-DVD, MP3, WMA,
OGG Vorbis
OPTICAL: optical digital audio output
S-VIDEO: S-Video output
Audio:
Additional formats:
Regional code:
AVI, MPEG 4, Xvid, JPEG (Foto-CD)
or
- 2 -
Download from Www.Somanuals.com. All Manuals Search And Download.
C. Remote control
6. Safety instructions
OPEN/CLOSE : Open/Close the disc tray
Number buttons
q
w
e
r
t
y
u
i
o
a
s
d
f
g
h
j
k
l
;
2)
2!
2@
2#
2$
2%
2^
2&
2*
2(
3)
3!
3@
3#
•
This device is not intended for use by individuals (including children)
with restricted physical, physiological or intellectual abilities or deficiences
in experience and/or knowledge unless they are supervised by a person
responsible for their safety or receive from this person instruction in how
the device is to be used.
DISPLAY: Superimpose disc information
DIMMER: Adjust the display brightness
V-MODE: Set the video output
STOPꢂ: Stop playback
PLAY/PAUSEꢀꢁ: Start/Suspend playback
•
•
•
•
Children should be supervised to ensure that they do not play with the
device.
To avoid unintentionally switching on the device pull the power cord
from the mains supply after use and before cleaning.
Check the device and all parts for visible damages. The safety concept
can work only if the device is in a faultless condition.
The power plug must always be easily accessible, so that the device can
be quickly disconnected from the mains in the event of an emergency.
:
SKIP FWD
Chapter skip forwards
VOL +/- : Raise/lower the sound level
FAST FWDꢃ: Fast search forward
SUBTITLE: Set the subtitle
ENTER: Confirm input
Control buttons ꢄꢀꢅꢆ
MENU: Access disc menu
SLOW: Slow motion function
RETURN: Set the playback mode
ZOOM: Set the image enlargement
PROG: Access the programme function
Battery compartment (on the rear panel)
PBC: PBC function activate/deactivate (VCD, SVCD only)
A-B: Repeat sequence
Risk of electrical shocks!
•
Connect the device only to correctly installed and earthed mains sockets.
Ensure that the rating of the local power supply tallies completely with
the details given on the rating plate of the device.
•
•
•
•
Arrange for defective power plugs and/or cables to be replaced at
once by qualified technicians or our Customer Service Department.
Arrange for customer service to repair or replace connecting cables
and/or devices that are not functioning properly or have been damaged.
Never immerse the device in water. Wipe it only with a slightly damp
cloth.
STEP: Individual frame playback
L/R/ST: Set the audio channel
AUDIO: Set the audio language
TITLE: Access the title menu
FAST RWDꢇ: Fast search backwards
Do not expose the device to rain and never use it in a humid or wet
environment.
SKIP BWD
: Chapter skip backwards
MUTE : Switch the sound on/off
REPEAT: Set the repeat function
•
•
Ensure that the power cable never becomes wet during operation.
You must not open the housing or repair the device yourself.
Should you do so, device safety can no longer be assured and the
warranty will become void.
ANGLE: Change the camera perspective
SETUP: Access the OSD menu
GOTO:Access titles, chapters and time direct select menus
STANDBY : Switch the device to standby mode
•
Protect the device against drip and spray water. Do not place any
water-filled vessels (e.g. flower vases) on the device.
Risk of fire!
5. Setting up of the DVD player
•
•
Do not use the device in the vicinity of hot surfaces.
Do not locate the device in places exposed to direct sunlight.
If you do, it may overheat and become irreparably damaged.
Do not leave the device unattended when in use.
Never cover the ventilation slots of the device while it is being used.
Do not place any open sources of fire, like candles, on the device.
1. Carefully remove the DVD player and the supplied accessories from
the packing.
2. Remove the protective foil from the display.
3. Place the DVD player on a flat, even and firm base. Do not subject the
device to any external heat or moisture source. Make sure that the device
has sufficient ventilation on all sides. Do not place any television directly
on top of the DVD player.
•
•
•
Injury hazard!
•
Keep children away from the connecting cable and the device.
Children frequently underestimate the dangers of electrical equipment.
Ensure that the device stands with a safe and secure positioning.
Do not operate the device if it has sustained a fall or is damaged.
Arrange for the device to be checked and/or repaired by qualified
technicians.
Attention!
•
•
Do not plug the DVD player into an electrical outlet at this time.
Wait until you have connected the DVD player to a television set.
In the event that you wish to change the type of video or audio connection
you must first pull the power plug from the power socket! Otherwise the
DVD player and possibly equipment connected to it could become
irreparably damaged through voltage peak strikes!
•
•
Batteries/ battery cells are potentially fatal if swallowed. Store batteries
out of the reach of children. If a battery is swallowed medical assistance
must be sought immediately.
Also, store the packaging foils well away from children. There is a risk
of suffocation.
- 3 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Danger! Laser radiation!
This device is fitted with a „Class 1 Laser“.
• Never open the device.
7. Remote control
7.1 Inserting the batteries
• Never attempt to repair the device.
1. Open the battery compartment on the rear of the remote control.
2. Place the two supplied batteries type AAA (micro cells) into the battery
compartment. Make sure that the batteries are inserted in accordance
with the correct polarity.
• There is invisible laser radiation inside the device.
Do not expose yourself to the laser beam.
Note:
3. Replace the battery compartment cover.
Some aggressive furniture finishes can have a destructive influence on the
device's rubber feet. If necessary, place the device on a nonslip pad.
7.2 Using the remote control
In order to guarantee faultless operation when using the remote control…
Thunderstorms!
•
•
Always point the remote control, during use, directely at the DVD player
Make sure that there are no obstructions between the remote control
and the DVD player that will hinder reception.
Equipment connected to a power supply can be damaged during a
thunderstorm. You should therefore always pull the power plug from the
power socket when there is a storm.
•
When using the remote control place yourself not more than 5 metres
from the DVD player
Notice regarding electrical power surges
(EFT / electrical fast transient) and electrostatic discharges:
otherwise interferences can occur during operation of the DVD player functions
with the remote control.
In the case of malfunction due to an electrical fast transient (power surge)
and/or electrostatic discharge, the device must be returned to default
settings in order to re-establish normal operation. The power supply may
have to be disconnected and then reconnected. The batteries (if present)
must be removed and then reinserted.
7.3 Replacing the batteries
If the operation of the DVD player via the remote control does not function
properly or does not function at all the batteries must be replaced
•
Always renew all batteries in order to return the remote control to its full
performance ability.
Notice regarding disconnection from mains-power
The POWER switch does not completely disconnect the device from
the power network. Additionally, the device consumes power when in
standby-mode. To completely disconnect the device from mains-power,
the power plug MUST be removed from the wall socket.
8. Connecting the DVD player to a television
After setting up the DVD player, you can now connect it to a television.
The DVD player can be connected to televisions which operate with the PAL
and NTSC standards.
If you want to use the DVD player on a television with the NTSC standard
you must change the video setting in the DVD players "OSD menu". There
PAL is set as the television standard at the factory. Depending on the televisions
equipment there are different methods of connecting the DVD player to it,
these are explained as follows.
Information regarding the handling of batteries
The remote control is operated by batteries.
For the safe handling of batteries please observe the following safety
information:
Danger exists from uses other than those intended!
Do not throw the batteries into a fire.
Do not short circuit the batteries.
Do not attempt to recharge the batteries.
Regularly check the condition of the battery. Leaking battery acid can
cause permanent damage to the device. When handling a damaged or
leaking battery special care should be taken. Danger from acid burns!
Wear protective gloves.
•
•
•
•
•
•
Clean the battery compartment and the battery contacts with a dry cloth.
Store batteries out of reach of children. When swallowed seek immediate
medical attention.
•
•
Remove the batteries from the device if you do not intend to use the device
for an extended period of time.
Never open batteries, never solder or weld batteries.
The risk of explosions and injuries exists!
Attention!
No liability/warranty will be considered for damage to the DVD player
caused by the effects of moisture, water penetration or overheating!
- 4 -
Download from Www.Somanuals.com. All Manuals Search And Download.
8.1 Connecting to a television via ScartCable/RGB
•
•
For playback select the matching channel on your television Check with
the television's instruction manual on how you can set the AV channel.
In the OSD menu select the menu option VIDEO/VIDEO OUTPUT/OFF .
Note:
Connecting the DVD player to a television with a Scart cable via the RGB input
offers a high quality connection. Select this connection variation in the case of
televisions equipped with an RGB input. If you are not sure if the television is
equipped with an RGB input then you can check this by consulting the television's
instruction manual.
The menu option VIDEO OUTPUT is only selectable when the HDMI output
is deactivated. On this subject see also chapter 10 "Settings in the OSD
menu".
8.3 Connection to a television via video input
(Composite Video)
For this connection variant the television must be equipped with Audio/Video
cinch sockets (Composite Video).
In order to connect the DVD player to a television via Composite Video you
will need
•
an audio/video RCA cinch cable (not supplied)
•
•
•
Connect the jack inscribed with SCART to a television Scart socket by
using the supplied Scart cable.
For playback select the matching channel on your television Check with
the television's instruction manual on how you can set the AV channel.
In the OSD menu select under the VIDEO/VIDEO OUTPUT/RGB or
OFF menus.
The menu option VIDEO OUTPUT is only selectable when the HDMI output
is deactivated. On this subject see also chapter 10 "Settings in the OSD
menu".
•
•
Connect the yellow marked video socket with the yellow VIDEO socket on
the television.
Connect the audio output sockets AUDIO L/R on the rear panel of the
DVD player to the corresponding audio inputs on the television. Make
sure that the colour markings yellow, red and white correspond.
For playback select the matching channel on your television Check with
the television's instruction manual on how you can set the AV channel.
In the OSD menu select the menu option VIDEO/VIDEO OUTPUT/OFF.
8.2 Connecting to a television via S-Video
•
•
Note:
For this type of connection the television must have available an S-VIdeo input
and two audio "IN" cinch sockets. If you are not sure if the television is equipped
with S-Video and/or cinch sockets you can check this by consulting the television's
instruction manual.
The menu option VIDEO OUTPUT is only selectable when the HDMI output
is deactivated. On this subject see also chapter 10 "Settings in the OSD
menu".
For this connection variant you will need:
•
•
an audio cinch cable (not supplied)
an S-video cable (not supplied) These can be obtained from your dealer.
8.4 Connecting via component signal (YPbPr/YUV)
This connection variant is only possible with very high grade televisions,
LCD/Plasma screens or Video projectors.
To connect the DVD player to a television via S-video:
Check with the instruction manual of the corresponding playback device to
see if this connections variant is available. It is possible that additional playback
device settings may have to be implemented.
The so called "Component signal" is put out via the YPbPr socket of the DVD
player. Component signals are available in the form of the so called "YUV"
signal (Half image) as well as in the form of the so called "YPbPr" signal
(Full image/Progressive scan).
On this topic, please refer to Section 17. "Glossary / KeyWord Index".
The cable connections are the same in both cases; YPbPr-signal for Progressive
Scan however can only be used if the television (or Video projector), to which
you want to connect the DVD player, is capable of Progressive Scan. If you
are not sure whether the television (or Video projector), to which you want to
connect the DVD player is capable of Progressive Scan and has cinch sockets
available then you can check this by consulting the television's (or Video
projectors's) instruction manual.
•
•
Connect the jack inscribed with S-VIDEO to a television S-Video socket
using an S-Video cable.
Connect the audio output sockets AUDIO L/R on the rear panel of the DVD
player via an audio cinch cable to the corresponding audio inputs on
the television. Make sure that the red and white colour markings
correspond.
- 5 -
Download from Www.Somanuals.com. All Manuals Search And Download.
For both variations – "YPbPr" and "YUV"– you will need
•
•
an audio cinch cable (not supplied)
an YUV cable (not supplied) These can be obtained from your dealer.
9. Connecting audio components to the
DVD player
On the rear panel of the DVD player you will find the connection sockets
Y, Pb/Cb and Pr/Cr.
Besides sound playback of DVDs, VCDs/S-VCDs and audio and MP3-CDs
via the speaker of the television, to which the DVD player is connected,
sound can also be played back via external audio components such as
a HiFi system, Dolby digital/DTS receiver or a surround sound system.
Connecting the DVD player via component signal:
9.1 Requirements for the connection of a HiFi system
In order to enjoy a full sound experience when playing DVDs with the DVD
player you can connect a HiFi system to the player. Before connecting check
with the HiFi system's instruction manual to verify...
•
•
if the HiFi system is suitable for connection to a DVD player.
if the HiFi system is equipped with cinch sockets; if yes, you can connect
the HiFi system to the DVD player via cinch cables.
Connecting a HiFi system:
•
•
Connect the sockets Y (green), Pb/Cb (blue) and Pr/Cr (red) with the
corresponding sockets on the television.
Connect the audio output sockets AUDIO L/R on the rear panel of the
DVD player to the corresponding audio inputs on the television with an
audio cinch cable.
Make sure that the red and white colour markings correspond.
•
For playback select the matching channel on your television Check with
the television's instruction manual on how you can set the AV channel.
In the OSD menu select the menu option VIDEO/VIDEO OUTPUT/YUV.
•
The menu option VIDEO OUTPUT is only selectable when the HDMI output
is deactivated. On this subject see also chapter 10 "Settings in the OSD
menu".
•
•
Connect the audio output sockets AUDIO L/R on the rear panel of the DVD
player to the corresponding audio inputs on the HiFi system with an audio
cinch cable. Make sure that the red and white colour markings correspond.
Check with the instruction manual which settings on the HiFi system may
be necessary in order to reproduce sound via the HiFi system during the
playback of a DVD, VCD/S-VCD, audio or MP3-CD from the DVD player.
8.5 Connecting to a television via HDMI
This connection variant is only possible with very high grade televisions,
LCD/Plasma screens or Video projectors
Check with the instruction manual of the corresponding playback device to
see if this connections variant is available. It is possible that additional play-
back device settings may have to be implemented. For this type of connection
you will need the HDMI cable (supplied);
Note:
For an optimal sound experience place your HiFi system's loud speakers to
the left and to the right of the television, on which you connected the DVD
player.
Connecting the DVD player via HDMI:
If you connected the DVD player to the television via a Scart cable the audio
signal will be transmitted via the cinch cable to your HiFi system as well as
via the Scart cable to the television. In this case, set the volume of the television
to the lowest value.
•
•
•
Connect the jack inscribed with "HDMI" using a HDMI cable to the
corresponding socket on the television.
For playback select the matching channel on your television Check with
the television's instruction manual on how you can set the AV channel.
In the OSD menu select the menu option VIDEO/HDMI Setup/ON.
On this subject see also chapter 10 "Settings in the OSD menu".
- 6 -
Download from Www.Somanuals.com. All Manuals Search And Download.
9.2 Connecting digital audio components via digital cables
In order to enjoy sound playback throughout the room from correspondingly
equipped DVDs (recognizable by the Dolby Digital or DTS logos), you can
connect the DVD player to a digital audio component, for example, a Dolby
Digital or DTS receiver or a suitable surround sound system.
The cables necessary for the following described connection variations can
be obtained from your dealer.
Note:
Make sure that no dirt can enter into the optical cable socket. This could cause
signal interference. Always insert the protective plug into the socket if no optical
cable is connected.
Firstly check with the digital component’s instruction manual to see if it allows
for connection to the DVD player...
•
•
via a coaxial cable
or via an optical cable.
Connection via coaxial cable
To connect the DVD player to a digital audio component with a digital coaxial
cable:
9.3 Connecting audio components via an analogue cable
If a digital input is not available on the audio component you can connect
the DVD player to it via conventional analogue cinch cables.
•
Connect the COAXIAL inscribed plug to the corresponding socket on the
digital audio component.
To connect the DVD player with analogue cables:
Connecting via optical cable
To connect the DVD player to a digital audio component with an optical cable:
•
Plug a cinch cable into each of the sockets FL (front left channel),
FR (front right channel), SL (rear left channel), SR (rear right channel),
CEN (front centre channel) and SW (Bass) on the rear panel of the DVD player.
Insert the cinch cables into the corresponding analogue inputs of the
audio component.
•
Remove the protective plug from the OPTICAL inscribed socket on the rear
panel of the DVD player and insert the optical cable plug.
Insert the plug at the other end of the optical cable in the corresponding
socket of the digital audio component.
•
•
9.4 Connecting the headphones
Note:
The headphones output is located on the front panel of the DVD player.
•
Plug the 3.5 mm headphones jackplug into the headphones output.
The optical cable is a glass fibre cable and must not be bent during installation.
Otherwise the glass fibre contained in the cable could break and the cable
would become unusable.
Attention!
Listening to music with headphones for long periods and at high
volume levels can lead to hearing damage!
- 7 -
Download from Www.Somanuals.com. All Manuals Search And Download.
10. OSD menu settings
10.1 Using the OSD Menu
•
To access the DVD players OSD menu press the SETUP button on the remote
control. The OSD Menu with its menu options will appear on the television
screen:
All of the DVD player's settings can be made with the remote control via
the so called "On Screen Display" menu ("OSD menu" for short). The OSD
Menu will be superimposed on the television screen.
GENERAL
AUDIO
DOLBY
VIDEO PREFERENCE
Note:
TV DISPLAY
PS
In these instructions the English OSD menu is described. At any time you can
set the menu to your country's language as described in "GENERAL > OSD
LANGUAGE".
ANGLE MARK
ON
ENG
OFF
ON
OFF
OSD LANGUAGE
CLOSED CAPTIONS
SCREEN SAVER
GENERAL
AUDIO
DOLBY
VIDEO PREFERENCE
LAST MEMORY
TV DISPLAY
PS
ANGLE MARK
ON
ENG
OFF
ON
OFF
OSD LANGUAGE
CLOSED CAPTIONS
SCREEN SAVER
The following menu options can be selected:
GENERAL, AUDIO, DOLBY, VIDEO and PREFERENCE.
• With the control buttonsꢄꢀꢅꢆand the ENTER button you can carry
out all the settings in the menu.
• With the control buttons ꢄꢀyou can select a menu by moving the yellow
marking onto the corresponding menu symbol.
LAST MEMORY
Before you use the DVD player for the first time for playback of DVDs,
VCDs/S-VCDs or audio/MP3-CDs you must implement a few settings via the
OSD Menu. These settings are dependent amongst others on...
• With the control buttons ꢅꢆyou select an input in a menu by moving
the green bar over an input.
• With the control buttonꢀyou change an input in the sub menu and with
the control button ꢄyou move back to the previous menu level.
• To confirm a selection press the ENTER button.
•
•
the language, in which you want the OSD menu to be displayed
which TV standard corresponds to the television, to which you want to
connect the DVD player
All navigation possibilities in a current menu are displayed at the lower
•
Which image format your television can display
edge of the menu.
• To exit the OSD menu press the SETUP button again.
Administering settings via the OSD menu
•
First insert the connector plug of the DVD player's power cord into
a power socket.
10.2 Setup menu GENERAL
In this menu you can, for example, set the image presentation or the language
of the OSD menu.
•
To switch the DVD player on activate the POWER switch on the rear panel
of the DVD player. If the DVD player is already switched on but is in
standby mode, press the button STANDBY on the remote control to
switch the DVD player on. Standby mode is identified by the green LED
in the display on the front panel of the device.
GENERAL
AUDIO
DOLBY
VIDEO PREFERENCE
TV DISPLAY
PS
ANGLE MARK
ON
ENG
OFF
ON
OFF
The device will check to see if a disc is inserted. The SilverCrest logo appears
on the television screen:
OSD LANGUAGE
CLOSED CAPTIONS
SCREEN SAVER
LAST MEMORY
TV DISPLAY
Note:
The menu option TV DISPLAY is only selectable when the HDMI output
is deactivated.
-4:3/PANSCAN Select this setting to display broadcasts in the usual 4:3
format on a 4:3 television set. Broadcasts in the 16:9 format
will be displayed in full screen without the distracting bars
although the side edges of the image will be trimmed.
-4:3/LETTERBOX Display of a film in 16:9 format on a traditional 4:3 format
television. The image is displayed with black bars on the
lower and upper edges of the screen.
If no disc is inserted the notification NO DISC appears on the television
screen and in the display.
•
Firstly please familiarize yourself with the OSD Menu's operation by
means of the following brief introduction.
-16:9
This setting is recommended when using a wide screen
television in 16:9 format. An image in 4:3 format will be
adapted horizontally to the image width.
-Wide Squeeze An image in 4:3 format will be presented with black bars
on the right and left edges.
- 8 -
Download from Www.Somanuals.com. All Manuals Search And Download.
ANGLE MARK
-ON
-3D SURROUND Select this setting to produce a virtual surround effect from
If scenes are recorded on a DVD in different perspectives
this will automatically be signified by a camera symbol
displayed on the television screen. Press the ANGLE button
on the remote control to display the various perspectives.
Deactivate function. No symbol appears on the television
screen.
a stereo or multi channel sound.
-5.1 CH
Select this setting to activate the analogue 5.1 outputs.
FRONT SPEAKER, CENTER SPEAKER, REAR SPEAKER and SUBWOOFER
In these menu inputs you can activate/deactivate the individual speaker types
and set the size.
-OFF
-Large
Select this setting if the diameter of the speaker membrane
is greater than 12 cm.
OSD LANGUAGE
Here you set the language, in which the OSD Menu will be shown on the
display.
-Small
-OFF
Select this setting for smaller speakers.
Deactivate sound output for these types of speakers
CLOSED CAPTIONS
Note:
-ON
Select this setting if by every playback of a DVD the subtitle
(if present) is to be automatically displayed on the television
screen.
The menu input FRONT SPEAKER can not be deactivated since the sound
output for the front speakers always remains switched on.
-OFF
Select this setting to manually activate the subtitle.
The subtitles can also be set, during playback, with the
SUBTITLE button.
DIALOG
In this menu input you can set the dialogue volume (0-20).
D.R.C. (Dynamic Range Control)
-ON
Function activated
SCREEN SAVER
-ON
-OFF
-AUTO
Function deactivated.
Function (if available) is automatically activated
Screen saver activated. The screen saver will now switch
on when the playback is stopped and no activity takes
place for several minutes.
-OFF
Deactivate function.
DIGITAL AUDIO
DIGITAL OUTPUT
LAST MEMORY
-ON
In this menu input you can set the SPDIF output signal.
Select this setting to playback a disc from the previously
halted position after removal and re-insertion.
-SPDIF / OFF
No digital audio signal is being put out at the sockets
COAXIAL or OPTICAL.
-OFF
Deactivate function. The disc playback starts back at the
begining after removing and then reinserting.
-SPDIF / RAW
-SPDIF /PCM
The crude data of the Dolby Digital sound is put out.
Select the setting PCM (Pulse Code Modulation) when there
is a connection to a digital amplifier/receiver. Your DVD
player transmits, through the PCM signal, the same audio
formats that are rendered on the disc. In addition an audio
signal will be put out via the sockets FL and FR.
Note:
If the DVD player is turned off with the POWER switch the saved position will not
be preserved.
LPCM OUTPUT Select this input to set the sampling frequency for the
10.3 Setup menu AUDIO
In this OSD menu you can, for example, carry out settings for the analogue
as well as the digital audio outputs.
processing of the crude data.
Default setting.
Only for DVDs with the corresponding sampling frequency.
-48K:
-96K:
GENERAL
AUDIO
DOLBY
VIDEO PREFERENCE
Note:
ANALOG AUDIO
DIGITAL AUDIO
CHANNEL DELAY
EQUALIZER
The LPCM OUTPUT function is only available if you have set the SPDIF audio
output signal to PCM.
CHANNEL DELAY
Select this menu input to set the channel delay of the individual speakers.
With optimal settings the sound reaches your ears simultaneously from all
directions.
3D PROCESSING
With the control button ꢀgo to the graphics field beside the input.
With the control buttons ꢅor ꢆselect the speaker.
With the control buttons ꢀꢄyou increase/decrease the value in increments
of 10 cm. The maximum setable deviation for the CENTER speaker is 170 cm.
The maximum setable deviation for the SUBWOOFER and the rear speakers
is 510 cm.
ANALOG AUDIO
DOWNMIX
If you use the analogue 5.1 output in this menu you can carry out the
appropriate settings.
Confirm your entry by pressing the ENTER button.
-LT/RT
Only the left and right channels at the sockets FL and FR
will put out signals.
Note:
-STEREO
A stereo sound will be put out. Select this setting if you are
not using the analogue 5.1 outputs. The menu options
CENTER SPEAKER and REAR SPEAKER are then not requi-
red and therefore inactive.
The channel delay is determined by the front speakers therefore these are not
selectable.
- 9 -
Download from Www.Somanuals.com. All Manuals Search And Download.
EQUALIZER
-SOUND MODE Select this menu input if, when playing back sound, you
want to use one of the preset equalizer levels ROCK, POP,
LIVE, DANCE, TECHNO, CLASSIC or SOFT. To deactivate
this function select the input OFF.
10.4 Setup menu DOLBY
In this OSD menu you can carry out settings for the Dolby-Digital output.
GENERAL
AUDIO
DOLBY
VIDEO PREFERENCE
-BASS BOOST
Select the setting ON if you want to boost the playback of
the base tone. To deactivate this function select the input OFF.
Select the setting ON to use the super base sound effect.
In addition playback of the base tone will be boosted.
To deactivate this function select the input OFF.
DUAL MONO
DYNAMIC
-SUPER BASS
-TREBLE BOOST Select the setting ON if you want to boost playback of the
treble sounds. To deactivate this function select the input OFF.
3D PROCESSING
Select this menu input if you want to activate/deactivate the Pro Logic II process.
DUAL MONO
DYNAMIC
Select this menu input to set the Dolby-Digital output to either
STEREO, L-MONO, R-MONO or MIX-MONO.
Select this menu input to enable an optimal sound playback
with reduced volume. In the setting FULL the louder passages
will be surpressed and the softer passages will be played
back louder.
Note:
The menu option PRO LOGIC II can only be selected if the analogue
5.1 outputs are activated.
-PRO LOGIC II Select the setting ON if the process is to be activated all
the time.
Note:
Select the setting AUTO if the process is only to be activated
when Dolby Pro Logic II encoded content is located on the
playback medium.
To deactivate this function select the input OFF.
In this menu you can set the Pro Logic II
process mode.
MUSIC: Sound is played back through the speakers
without delay.
MOVIE: Sound is played back with a delay of 10 ms
through the rear speakers.
This function is only possible when using a digital audio component.
10.5 Setup menu VIDEO
In this menu you can, for example, carry out settings for the video output,
resolution or colour.
-MODE
GENERAL
AUDIO
DOLBY
OFF
VIDEO PREFERENCE
VIDEO OUTPUT
RESOLUTION
COLOR SETTING
HDMI SETUP
PRO
LOGIC: Earlier version of the DOLBY PRO LOGIC processes.
AUTO: Automatic setting of the processes (depending on
the contents of the playback medium).
Xvid SUBTITLE
ENG
Note:
The menu inputs PANORAMA, DIMENSION and CENTER WIDTH serve to
fine tune the sound and are only available if you have set the process mode
MUSIC.
VIDEO OUTPUT
-OFF
The video signal will be put out via the S-video output and
the composite video output.
-PANORAMA
-DIMENSION
Select the setting ON to activate this sound enhancement.
To deactivate this function select the input OFF.
Select one of the settings SIZE -3 to SIZE 3 to activate this
sound enhancement.
-YUV
-RGB
The video signal will be put out in YUV colour format via
the component video outputs Y, Pb/Cb, Pr/Cr.
The video signal will be put out in RGB colour format via
the SCART connection.
-CENTER WIDTH Select one of the settings LEVEL 0-7 to receive a corresponding
sound enhancement.
Note:
This setting is only active if the HDMI setup is deactivated.
REVERB MODE Select this menu input if you want to use, for sound playback,
one of the preset reverbs CONCERT, LIVING ROOM, HALL,
BATHROOM, CAVE, ARENA, or CHURCH. To deactivate
this function select the input OFF.
The composite video output on the DVD player is always activated. If the selected
setting deviates from the actual connection variation (apart from composite video)
it is possible that no image or a poor image will be displayed on the television
screen. In this event press, when playback is stopped, several times the V-MODE
button on the remote control until the image is displayed properly.
- 10 -
Download from Www.Somanuals.com. All Manuals Search And Download.
RESOLUTION
In this menu input you can set the different resolutions
AUDIO
In this menu input you can set the language that is to be
the standard used when playing back films.
(480i/576i/720p/1080i/1080p for the HDMI
)
output/component video output.
SUBTITLE
DISC MENU
PARENTAL
Note:
In this menu input you can set the subtitle language that is
to be the standard used when playing back films.
In this menu input you can set the disc menu language that
is to be the standard used when playing back films.
In this menu input you can determine the age restrictions.
Note:
Be aware that for the TV standard PAL a setting with 50 Hz and for the TV
standard NTSC a setting with 60 Hz must be selected.
COLOR SETTING
In this menu input you can implement the settings, for example, for the brightness,
contrast or hue.
Only a few DVDs have a technical age restriction available. If there is no technical
age restriction on the DVD your DVD players child lock feature can not
be activated. The child lock can only function if it is activated on the DVD player
and a corresponding code is available on the inserted DVD.
-SHARPNESS
Select this menu input to set one of the predefined sharpness
values (HIGH, MEDIUM or LOW).
If you insert a DVD which, according to the child lock, may not be played back
a window appears on the screen, in which you must enter your password and
confirm with ENTER. Some DVDs and CDs are encoded with encryption signals.
In this way DVDs can be divided into eight different approval classes.
Select one of the following approval classes to protect the playback of
this media class with a password request:
-BRIGHTNESS
With the help of the control buttonsꢄꢀset the brightness
from -20 to +20. Subsequently press the ENTER button to
continue.
With the help of the control buttonsꢄꢀset the contrast
from -16 to +16. Subsequently press the ENTER button to
continue.
-CONTRAST
-GAMMA
-HUE
Select this menu to set one of the predefined gamma values
(HIGH, MEDIUM, LOW or NONE).
With the help of the control buttonsꢄꢀset the hue from -
1 KID SAFE:
2 G:
3 PG:
also suitable for young children
for all age groups
adult supervision recommended;
9 to +9. Subsequently press the ENTER button to continue.
4 PG 13:
adult supervision strongly recommended; some scenes are
not suitable for children under 12
for children under 16; adult supervision recommended
for children under 16; adult supervision strongly recommended
not for teenagers under 18 years of age
for adults only
-SATURATION With the help of the control buttonsꢄꢀset the saturation
level from -9 to +9. Subsequently press the ENTER button to
continue.
5 PGR:
6 R:
7 NC 17:
8 ADULT:
-LUMA DELAY
Select this menu input to set one of the predefined gamma
values (0 T or 1 T).
HDMI Setup
-ON
-OFF
Select this menu input to activate the HDMI output.
Select this menu input to deactivate the HDMI output.
In this menu input you can set the Xvid subtitle language
that is to be the standard used when playing back films.
Example
If a DVD was encoded with, for example, approval class 7 or 8 and you have
an approval class setting between 1 and 6 then a message follows and the
password must be entered. Also only parts of the DVD, that is to say certain
film scenes, may be encoded with an approval class or various approval classes.
Xvid SUBTITLE
10.6 Setup menu PREFERENCE
In this menu you can, for example, carry out the settings for the video output,
activate/deactivate the child lock or change the password.
•
To activate the approval class you must select, in the PARENTAL menu,
the desired approval class and enter the password (136900).
Confirm your entry by pressing the ENTER button.
Note:
PASSWORD
In this menu input you can change the factory default
password (136900) and assign your own password.
Only the numbers 0-9 can be used.
The menu option PREFERENCE is only selectable when playback is
completely finished.
GENERAL
AUDIO
DOLBY
PAL
VIDEO PREFERENCE
Note:
TV TYPE
In the event that you forget your new password you can use the factory preset
password (136900).
AUDIO
ENG
ENG
ENG
SUBTITLE
DISC MENU
PARENTAL
PASSWORD
DEFAULT
DEFAULT
In this menu input you can restore the DVD players factory
defaults.
TV TYPE
-PAL
PAL television standard
-NTSC
NTSC television standard.
- 11 -
Download from Www.Somanuals.com. All Manuals Search And Download.
11. Initial operation of the DVD player
12. Playing back DVDs, VCDs or S-VCDs
After you have …
To play back a DVD/VCD/S-VCD with the DVD player...
•
•
placed the DVD player in a suitable location
connected the DVD player to a television by one of the designated
connection options
connected the DVD player, if desired, to a HiFi or Surround system
(analogue/digital) for example a Dolby Digital or DTS receiver
made the remote control ready for operation by inserting the batteries
and know how to activate and operate the OSD menu with the remote
control
•
•
Switch on your television.
Make sure that the DVD player is ready for operation.
If the television, the DVD player and possibly other connected devices (i.e. an
audio component) are ready for operation and are switched on and the DVD
player is connected correctly to the television you will now see the "Silvercrest"
logo on the TV screen
•
•
•
… the DVD player is ready for operation.
11.1 Switching the DVD player on/off
• Insert the mains power cable into a properly installed mains power socket.
• Place the POWER switch on the rear panel of the device to the ON position.
The DVD player is now in standby mode.
• With the STANDBY
button on the remote control or the STANDBY
button
you switch the DVD player on and/or back to the standby
on the device
mode.
• To switch the DVD player off place the POWER switch on the rear panel of
the device to the OFF position.
• Open the disc tray on the front panel of the DVD player by pressing the
OPEN/CLOSE button.
OPEN now appears in the display on the front panel of the DVD player and
Note:
The device has no display indicators when it is switched off or in the standby
mode. In standby mode the standby LED lights up in the display.
on the television screen.
• Insert a DVD/VCD/S-VCD disc in the disc tray with the inscribed/labled
side up.
11.2 Inserting the DVD
To play a disc with the DVD player:
• Press the OPEN/CLOSE button again to close the disc tray.
CLOSE will appear in the display on the front panel of the DVD player and
on the television screen while the disc tray is closing.
• The contents of the inserted DVD/VCD/S-VCD will now be loaded; this
may take a few seconds. In the meantime LOADING blinks in the display
on the front panel of the DVD player and on the television screen.
• Playback of the inserted DVD/VCD/S-VCD starts automatically.
•
•
Switch on your television.
Make sure that the DVD player is ready for operation.
If the television, the DVD player and possibly other connected devices (i.e. an
audio component) are ready for operation and are switched on and the DVD
player is connected correctly to the television you will now see the Silvercrest
logo on the TV screen
If no disc is inserted into the DVD player's disc tray:
The message NO DISC is displayed on the television screen.
Note:
•
Open the disc tray by pressing the button
OPEN/CLOSE on the remote con-
DVDs, VCDs and S-VCDs that you want to playback with the DVD player
may possibly have a country code which is printed on the DVD's jacket.
trol or on the front panel of the DVD player. OPEN is displayed on the
television screen.
The DVD player can only playback DVDs/VCDs/S-VCDs with the country code
If no country code is printed on the cover of a DVD/VCD/S-VCD...
.
•
•
Insert the disc in the disc tray with the inscribed/labled side up.
For two-sided discs: The side you would like to play must face down.
After you have inserted the disc press the button
OPEN/CLOSE on the re-
mote control or on the front panel of the DVD player again to close the
• but instead the symbol
, then the DVD/VCD/S-VCD can be
disc tray.
played back with the DVD player
•
The contents of the disc will now be loaded; this may take a few seconds.
In the meantime LOADING is displayed on the television screen.
• then the DVD/VCD/S-VCD can possibly not be played back with the
DVD player. You can check this by attempting to play back the DVD.
Depending on the inserted DVD/VCD/S-VCD it is possible that the contents
of the DVD/VCD/S-VCD will not playback immediately, rather first a selection
menu appears on the television screen.
In this event select the menu option, which will start the playback of the film,
with the control buttons ꢄꢀꢅꢆon the remote control.
• To start playback of the film press the ENTER button on the remote control
or press the PLAY/PAUSEꢀꢁbutton.
- 12 -
Download from Www.Somanuals.com. All Manuals Search And Download.
In the display on the front panel of the DVD player, the following notices
appear:
With DVDs:
If such a menu is present on the DVD inserted in the DVD player you can access
it during playback by pressing the MENU button on the remote control.
You can select particular menu options by pressing the control buttons
ꢄꢀꢅꢆon the remote control.
To confirm the selected menu option press the PLAY/PAUSEꢀꢁbutton or the
ENTER button on the remote control.
•
•
•
"DVD"
the number of the currently playing chapter
the played back so far time of the currently playing DVD in minutes and
seconds
To return to playback press the MENU button on the remote control again.
With VCDs/S-VCDs:
Note:
•
•
•
"VCD" or "S-VCD"
If you cancel playback by pressing the STOPꢂbutton twice (Playback stop without
resume function) access to the disc's main menu is no longer possible.
the number of the currently playing title
the played back so far time of the currently playing VCD/S-VCD in
minutes and seconds
Playback Control (PBC) with VCDs/S-VCDs
Many VCDs/S-VCDs have Playback Control (in short "PBC"). Playback Control
indicates a main menu that allows operation of several functions of the
VCD/S-VCD.
If PCB is available on a VCD/S-VCD inserted in the DVD player you must first
activate it in order to be able to superimpose the menu.
• During playback or when playback is stopped press the MENU button.
The message PBC: OFF appears in the display.
12.1Features during playback of a DVD, VCD or S-VCD
During the playback of a DVD/VCD/S-VCD you can use the following DVD
player features...
Pause playback
To pause the playback of the inserted DVD/VCD/S-VCD...
•
During playback press the PLAY/PAUSEꢀꢁbutton
• Press the MENU button again. The message PBC: ON appears in the display.
PBC is now switched on the discs main menu can be accessed with the
MENU or TITLE buttons.
ꢁwill now appear in the display on the front panel of the DVD player and
on the television screen.
On the television screen you will see a freeze frame of the scene that has just
been halted.
Note:
•
To contnue playback of the film press the PLAY/PAUSEꢀꢁbutton.
If you switch on PBC during playback then it is possible that playback will
stop and start again from the beginning and/or with the main menu.
Stop playback (STOPꢂ)
To stop playback of the film on the inserted DVD/VCD/S-VCD press the
Skip to start of chapter (Skip)
STOPꢂbutton.
With resume function
Note:
If you have cancelled playback of the inserted DVD/VCD/S-VCD by pressing
the STOPꢂbutton once the DVD player automatically saves the position
where playback was interrupted. This function is called the "resume function".
PRESS PLAY KEY TO CONTINUE appears on the television screen. As
soon as you press the PLAY/PAUSEꢀꢁbutton again playback will continue
from the saved position.
This function may not be available on all DVDs! If you attempt to execute
a function that is not available, the symbol
screen.
is displayed on the television
With the buttons SKIP FWD
and SKIP BWD
you can, during playback,
within the film on the inserted DVD/VCD/S-VCD …
Without resume function
•
•
skip forward to the beginning of the next chapter or
skip backward to the preceeding chapter
If you have cancelled playback of the inserted DVD/VCD/S-VCD by pressing
the STOPꢂbutton once and you press the STOPꢂbutton a second time the
saved position, at which you interrupted the playback, will be cleared.
When you press the PLAY/PAUSEꢀꢁbutton again playback of the inserted
DVD/VCD/S-VCD starts from the beginning.
The respectively selected chapter will playback immediately without having
to press the PLAY/PAUSEꢀꢁbutton. The number of the respectively selected
chapter will be displayed on the front panel of the DVD player to the left of
the played back so far time.
Access the DVD menu (MENU)
Title number input via the number buttons
Note:
Note:
This function may not be available on all DVDs! If you attempt to execute
This function may not be available on all DVDs! If you attempt to execute
a function that is not available, the symbol
screen.
is displayed on the television
a function that is not available, the symbol
screen.
is displayed on the television
With many films on DVDs there is a main menu on the disc which, apart from
the option of playing back the main film, allows you to select from the following
contents:
Instead of using the Skip function you can also enter the title from within the
film on the inserted DVD/VCD/S-VCD direct by entering the title number via
the number buttons on the remote control.
•
•
•
the subtitle and film dialogue languages
direct chapter selection
to playback the films bonus material (Background information,
"Making of" etc.)
•
For this, during playback or when playback is stopped, press the number
buttons on the remote control corresponding to the title number, for
example, the 3 button for the third title.
•
Playback of the entered title number will now start automatically.
- 13 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Direct chapter or time selection via the Search function (GOTO)
Fast scan forward/backward
With fast scan you can select designated passages from the inserted
Note:
DVD/VCD/S-VCD during playback.
•
For fast scan forwards/backwards press the ꢃFAST FWD and/or ꢇFAST RWD
This function may not be available on all DVDs/VCDs/S-VCDs! If you attempt
button repeatedly to set the following fast scan speeds:
to carry out functions that are not available the symbol
on the television screen.
will be displayed
Entry of the time position via search function DVD, VCD and SVCD:
• During playback press the GOTO button on the remote control. The time
menu is superimposed on the television screen:
MENU
TITLE
01 / 13
02 / 05
2 CH
Note:
CHAPTER
AUDIO
SUBTITLE
ENGLISH
During fast scan no sound will be played back.
ENGLISH
• To continue playback of the film at the selected place in normal
speed press, during fast scan the PLAY/PAUSEꢀꢁbutton.
BITRATE
50 IIIIIIII
TITLE ELAPSED 0:00:56
• The entry field TITLE is automatically selected first. Press the ENTER button
and enter, with the number buttons, the desired title. On DVDs title 01 is
most often the main film.
Slow playback forward (Slow motion)
To playback the contents of the inserted DVD/VCD/S-VCD in slow motion …
•
For slow playback forwards press the SLOW button repeatedly to set the
• Press the navigation button ꢆto select the entry field CHAPTER. Press the
ENTER button and enter, with the number buttons, the desired chapter.
• Press the navigation button ꢆto select the entry field AUDIO. Press the
ENTER button and select, with the navigation buttons ꢅꢆ, an audio language.
• Press the navigation button ꢆto select the entry field SUBTITLE. Press the
ENTER button and select, with the navigation buttons ꢅꢆ, a subtitle language.
• Press the navigation button ꢆto select the entry field ANGLE. Press the
ENTER button and select, with the navigation buttons ꢅꢆ, another camera
perspective (if available).
following playback speeds:
Note:
• Press the navigation button ꢆto select the entry field TT TIME. Press the
ENTER button and enter, with the number buttons, the desired title time.
• Press the navigation button ꢆto select the entry field CH TIME. Press the
ENTER button and enter, with the number buttons, the desired chapter time.
• Press the navigation button ꢆto select the entry field REPEAT. Press the
ENTER button and select, with the navigation buttons ꢅꢆ, a repeat function
(see also repeat functions).
During slow motion playback no sound will be played.
•
To continue playback from a selected position in normal speed, during
slow motion playback press the PLAY/PAUSEꢀꢁbutton.
Image enlargement (Zoom)
• Press the navigation button ꢆto select the entry field TIME DISP. Press
the ENTER button and select, with the navigation buttons ꢅꢆ, a time
presentation (see also superimpose disc information).
Note:
This function may not be available on all DVDs! If you attempt to execute
a function that is not available, the symbol
screen.
is displayed on the television
• To fade the menu out press the GOTO button again.
Audio CD
During the playback of an inserted DVD/VCD/S-VCD you can enlarge the
image on the television screen in three levels. For this press the ZOOM button
on the remote control to set the following enlargement levels:
• During playback press repeatedly the GOTO button on the remote control.
The following notices appear, one after the other, in which you can enter
a time position with the number buttons:
DISC GOTO:
Enter here a time position on the disc from where playback
should start.
TRACK GOTO: Enter here a time position for the currently playing back
title from where playback should start.
GOTO TRACK: Enter here a title number from where playback should start.
With the control buttons ꢄꢀꢅꢆsections of the enlargement can be
suspended.
MPEG CD
SELECT:
Enter here a title number on the disc from where playback
should start.
To switch off the enlargement function and return to the normal image
size press repeatedly the ZOOM button.
GOTO:
Enter here a time position for the currently playing back
title from where playback should start.
- 14 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Change camera aspect (Angle)
Programmed playback (PROG)
Note:
Note:
This function may not be available on all DVDs! If you attempt to execute
This function may not be available on all DVDs/VCDs/S-VCDs! If you attempt
a function that is not available, the symbol
screen.
is displayed on the television
to execute a function that is not available, the symbol
television screen.
is displayed on the
Many films on DVD contain chapters which were recorded simultaneously
from various camera perspectives. With films that have such chapters availa-
ble you can view the same chapter from different perspectives.
For this press the ANGLE button on the remote control during playback of an in-
serted DVD. Each press of the ANGLE button will switch to one of the available
camera perspectives.
With the "Programme" function you can put together your own film programme
in so far as you can select only certain chapters of an inserted DVD/VCD/S-VCD
for playback. In this way you can determine for yourself the sequence, in which
the chapters are played back. You can compile a maximum of 20 chapters
of a film for programmed play.
•
Press the PROG button on the remote control during playback or when
playback is stopped.
Superimpose/fade out subtitles
The Programme menu will be displayed on the television screen.
Note:
Programme window
This function may not be available on all DVDs! If you attempt to execute
a function that is not available, the symbol
screen.
is displayed on the television
1
2
3
4
5
6
7
TT:
TT:
TT:
TT:
TT:
CH:
CH:
CH:
CH:
CH:
TT:
TT:
TT:
TT:
CH:
CH:
CH:
CH:
8
9
If the film on the inserted DVD has subtitles available you can superimpose
these on the television screen during playback by pressing the SUBTITLE button
on the remote control.
10
EXIT
With the first press of the SUBTITLE button the subtitle of the first available
language will be superimposed on the television screen. With each further
press of the SUBTITLE button the subtitles of other available languages will be
superimposed successively on the television screen.
First are listed the programme positions 1-10, programme position 1 is
highlighted.
1. With the number buttons enter the number of the title that is to be played
back first. The highlight changes to chapter entry (CH:).
The number of the currently superimposed subtitle language will be superimposed
on the television screen ( i.e. 1/10 for the first of ten available subtitle languages).
2. With the number buttons enter the number of the chapter that is to be
played back. The highlighting moves to the programme position 2.
3. Select, with the navigation buttons ꢄꢀꢅꢆ, further programme positions
and enter title and chapter numbers for the programme positions.
• To display the next 10 programme positions select, with the navigation
buttons ꢄꢀꢅꢆ, the field ꢈand press the ENTER button.
You can allocate up to 20 programme positions.
When the last of the available subtitle languages is superimposed (i.e. 10/10
for the tenth of ten available subtitle languages) you can switch off the subtitle
function by pressing the SUBTITLE button again. OFF is superimposed on the te-
levision screen.
• To delete entries in a programme position select the programme position
and press the ENTER button.
Change playback language
• To stop the programme function select the field EXIT and press the ENTER
button. All allocated programme positions are deleted.
Note:
4. You start playback of the programme positions by selecting the field
START and press the ENTER button.
During the programmed playback the notice PROGRAM appears in the display.
To delete the programmed playback press twice, during playback, the STOPꢂ
button on the front panel of the DVD player or on the remote control.
This function may not be available on all DVDs! If you attempt to execute a
function that is not available, the symbol
screen.
is displayed on the television
With many films on DVD you can, during playback, select another playback
language by pressing the AUDIO button on the remote control.
The first press of the AUDIO button switches to the first available playback language.
With each further press of the AUDIO button other available playback languages,
one after the other, are switched on.
Note:
If you are not sure what number a title and/or chapter to be programmed has
then select the corresponding chapter, during playback of the film, with the
buttons SKIP FWD
and SKIP BWD
and susequently press the DISPLAY button
The currently switched on playback language will be superimposed on the
television screen.
on the remote control to superimpose all information from the inserted DVD/VCD/
S-VCD onto the television screen. Here you will find, amongst others, the current
title and chapter numbers.
On this topic see also the section "Superimpose disc information".
- 15 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Superimpose disc information
Repeat function with MP3/WMA/MPEG/ JPEG/Xvid discs
During playback press the REPEAT button several times to apply the following
repeat functions (the set function appears in the display):
RANDOM
Random playback of the titles on the disc and/or the data carrier.
SINGLE
Note:
This function may not be available on all DVDs/VCDs/S-VCDs! If you attempt
to execute a function that is not available, the symbol
television screen.
is displayed on the
With this function you can superimpose all the available information from
a DVD/VCD/S-VCD inserted into the DVD player onto the television screen
during playback.
One time playback of the current title/image.
REPEAT ONE
Endless repeat of the current title/image.
REPEAT FOLDER
•
For this, during playback, press the DISPLAY button on the remote control.
On the television screen will be superimposed:
Repeat all titles of the current folder on the disc and/or data carrier.
REPEAT ALL
With DVDs:
Repeat all titles on the disc and/or data carrier.
• the current title number/the total number of titles
• the current chapter number/the total number of chapters
• the played back so far time in hours, minutes and seconds (TITLE ELAPSED)
• the time to the end of the film in hours, seconds and minutes (TITLE REMAIN)
• the played back so far time of the chapter in hours, minutes and seconds
(CHAPTER ELAPSED)
Repeat sequence (A–B)
With this function you can repeat playback of a favourite sequence within
a chapter of the current playback disc.
To do this …
• During playback press the A – B button on the remote control as soon as the
• the time to the end of the chapter in hours, seconds and minutes
(CHAPTER REMAIN)
desired sequence starts to playback.
A appears on the television screen.
• Press the A – B button again as soon as the end of the desired sequence is
played back. Pay careful attention to the fact that the start and finish of
the sequence must be located within a chapter.
With VCDs/S-VCDs:
• the current title number/the total number of titles
• the played so far time of the current playback title on the VCD/SVCD in
hours, minutes and seconds (SINGLE ELAPSED)
• the time to the end of the current playback title in hours, seconds and minutes
(SINGLE REMAIN)
AB appears on the television screen.
Repeat playback of the selected sequence begins immediately without you
having to press the PLAY/PAUSEꢀꢁbutton. The sequence will continuously re-
peat until you press the A – B button again in order to switch off the function.
To stop display of the disc information press repeatedly the DISPLAY button
until the notice DISPLAY OFF appears on the television screen.
Setting playback volume
Press the VOL + button on the remote control during playback to increase play-
back volume or the VOL – button to reduce playback volume.
Repeat function for DVDs, VCDs, S-VCDs and audio CDs
With the repeat function you can…
Dimmer
... in the case of DVDs, selectively repeat title, chapter or the entire DVD.
... in the case of VCDs/S-VCDs individual titles and/or the entire VCD/S-VCD
repeatedly playback.
Press the DIMMER button on the remote control to change the DVD player's
display brightness in three levels.
... in the case of audio CDs, playback repeatedly a particular track and/or
the entire CD.
To switch on repeat playback...
To switch playback sound to mute (MUTE)
To switch the playback sound to mute press the (MUTE) button on the remote
control during playback of DVDs, VCDs/S-VCDs, audio CDs and CD-Rs/CD-RWs
with MP3 or WMA data. MUTE is displayed on the television screen.
When you want to switch the playback sound back on press the (MUTE) button
again or the VOL + and VOL – buttons. MUTE OFF or the corresponding volume
level is displayed on the television screen.
• Press the REPEAT button several times during playback.
The repeat symbol
notifications:
CHAPTER
appears in the display with one of the following
Select CHAPTER to continuously repeat the currently playing
back chapter until repeat playback is switched off or play-
back is cancelled by pressing the STOP ꢂbutton twice.
Select TITLE to continuously repeat the currently playing
back title until repeat playback is switched off or playback
is cancelled by pressing the STOP ꢂbutton twice.
Select ALL to continuously repeat all available titles on the
disc, thus the entire disc, until playback repeat is switched
off or playback is cancelled by pressing the STOPꢂbutton
twice.
Switching off the DVD player
To switch off the DVD player:
TITLE
ALL
•
In the event that a disc inserted into the DVD player is playing back, first
cancel playback by pressing the STOPꢂbutton on the front panel of the
DVD player or on the remote control twice.
•
Open the disc tray to remove a currently inserted disc from the DVD
player by pressing the OPEN/CLOSE button on the front panel of the
DVD player or on the remote control. Subsequently close the disc tray
by pressing the OPEN/CLOSE button again.
To switch off repeat playback press the REPEAT button repeatedly, during play-
back, until no more notifications appear on the television screen.
•
•
Press the STANDBY button on the remote control. The DVD player now
switches to the STANDBY mode. To switch the DVD player back on press
the STANDBY button again.
To switch the DVD player off completely activate the POWER switch on
the rear panel of the DVD player.
- 16 -
Download from Www.Somanuals.com. All Manuals Search And Download.
1. To open a folder select the folder and press the ENTER button. The contents
13. Playback of JPEG-Photo
CD/WMA/MP3/MPEG4
of the folder will be listed.
2. To reach a higher folder level select the symbol
press the ENTER button.
with the entry ".." and
Insert a storage medium into the DVD player.
The contents of the data carrier (CD or DVD) will be displayed on the
television:
Playback of JPEG discs
• With the navigation buttons ꢅꢆhighlight an image and press the ENTER
button or the PLAY/PAUSEꢀꢁbutton to open the image.
The image is shown on the display
Display of MP3 data
Subsequently change the view to the next available image on the disc/in the
folder.
00:23
001/058
03:56 160 Kbps
• To display the currently shown image press the PLAY/PAUSEꢀꢁbutton longer.
• To continue the playback press the PLAY/PAUSEꢀꢁbutton again.
• You can access an image directly by entering the image's file number with
the number buttons and subsequently confirm the entry with the ENTER button.
• With the navigation buttons ꢄꢀyou can rotate the image in 90° increments
during playback.
\ music
..
01 track01
02 track02
03 track03
04 track04
05 track05
06 track06
• With the navigation buttons ꢆꢅyou can mirror the image horizontally
or vertically during playback.
DISC
DISC
DISC
• During playback press the STOPꢂbutton to display a miniature view of all
images in the folder/on the disc. 12 miniatures will be displayed on each
page.
• Select with the navigation buttons ꢄꢀꢅꢆan image and start playback
with ENTER or PLAY/PAUSEꢀꢁ.
Display of JPEG data
00:00
00:00
001/037
• Select with the navigation buttons ꢄꢀꢅꢆone of the following entries
\ pictures
from the bottom display lines and confirm the entry with the ENTER button.
..
picture 01
picture 02
picture 03
picture 04
picture 05
picture 06
Slide Show
Menu
Starts a slide show of the images in the folder/on the disc
Shows the available button functions for JPEG playback.
Press the ENTER button until this menu has faded out.
switches to the previous page
Prev
Next
switches to the next page
• Press the MENU button to switch to the file list again
Display of AVI and MPEG data
Selection of slide show transitions:
00:00
00:00
You can select different transitions for changing from one image to the next.
WIPE TOP, WIPE BOTTOM, WIPE LEFT, WIPE RIGHT, DIAGONAL WIPE
LEFT TOP, DIAGONAL WIPE RIGHT TOP, DIAGONAL WIPE LEFT BOTTOM,
DIAGONAL WIPE RIGHT BOTTOM, EXTEND FROM CENTER H, EXTEND
FROM CENTER V, COMPRESS TO CENTER H, COMPRESS TO CENTER V,
WINDOW H, WINDOW V, WIPE FROM EDGE TO CENTER and NONE.
001/006
\ videos
..
video 01
video 02
video 03
video 04
video 05
video 06
• During the slide show press the PROG button until the name of the desired
transition appears in the upper left corner of the television screen.
• The data is listed on the left (Data window). Folders will be depicted with
the symbol
.
• To superimpose the folders available on the disc press the PROG button
repeatedly until the notice FOLDER appears at the bottom of the display.
• Press the PROG button again repeatedly until the notice FILELIST appears at
the bottom of the display. Folders will now be faded out and all data on
the disc is represented in a list.
• The area on the right is intended for the previewing of JPEG images.
A preview appears as soon as you highlight a JPEG file in the file window.
• At the bottom is located the information bar, in which is displayed the image
size (JPEG Image) as well as the medium (DISC), on which the files are
located.
• Select a file with the aid of the navigation buttons ꢅꢆ. You confirm the
selection by pressing the ENTER button. The file will be played back and/
or the JPEG Photo displayed.
- 17 -
Download from Www.Somanuals.com. All Manuals Search And Download.
The display shows "No Disc" even though there is a disc inserted
14. Cleaning of the DVD player
A
The disc is dirty, scratched or damaged. Clean the disc or insert another
disc.
Clean the housing of the DVD player with a slightly damp cloth and a mild
cleanser only. When cleaning, make sure that no moisture gets into the DVD
player!
B
The Country/Region code on the inserted DVD/VCD/S-VCD does not
correspond to the Country/Region code of the DVD player. In this case
the DVD/VCD/S-VCD cannot be played with the DVD player.
Clean the inside of the disc tray, if necessary, exclusively with a clean dry
brush (i.e. a lens brush obtainable from a photographic dealer).
Never clean the inside of the disc tray with anything moist!
Inserted disc will not playback
It is possible that a layer of condensation has built up on the DVD players laser
scan lens. This can be the case especially if the DVD player has been subjected
to strong temperature fluctuations.
Warning!
If this is the case place the DVD player in a dry environment at normal room
temperature. First remove the currently inserted disc from the disc tray.
Then leave the DVD player switched off for at least one hour without using
until the condensation film has evaporated.
Moisture penetrating into the DVD player creates the risk of an electric shock!
The DVD player may also be irreparably damaged!
15. Disposal
No image or Black/White image only
A
Check to make sure that all connection cables between the DVD player
and the television (or Video projector) are firmly inserted into the
corresponding sockets
Disposing of the device
Do not, under any circumstances, discard the device in the household
refuse. This product is subject to the European directive 2002/96/EC.
B
Check to make sure that the settings in the OSD menu match the connections
variant, with which you have connected the DVD player to the television
(or Video projector).
Dispose of the device through an approved disposal centre or at your community
waste facility.
For this see chapter 8. "Connecting the DVD player to a television".
Observe the currently applicable regulations. In case of doubt, please contact
your waste disposal centre.
C
Check by means of the televisions (or Video projectors) operating
instructions to see if settings to the television (or Video projector) may
be necessary in order to use the DVD player with the television.
Disposing of batteries!
Do not dispose of the batteries with household waste. Every consumer is legally
obliged to dispose of batteries at a collection site in his community/city district or
at a retail store.
No sound
A
Check to see if the television and/or DVD player have possibly been
This obligation is intended to ensure that batteries are disposed of in an
environmentally friendly manner.
Only dispose of batteries when they are fully discharged.
switched to mute.
B
Check to see if all connection cables between the DVD player and potentially
connected audio components are plugged firmly into the corresponding
sockets.
Disposal of packaging
C
Check whether the settings in the OSD menu match the connection option
you have used to connect the audio components to the DVD player.
Dispose of the packaging materials in an environmentally
responsible manner.
For this see chapter 9. "Connecting an audio component to the
DVD player".
16. Troubleshooting
D
E
Using the television's instruction manual check to see if current settings to
the television are necessary in order to use the DVD player with the tele-
vision.
Check by means of the operating instructions for a potential connected
audio component if settings to it are necessary in order to use it with the
DVD player.
Display is blank/DVD player shows no functions even though it is
switched on
A
Check to see that the power cable is inserted properly into the power
socket.
F
If you …
B
Check to ensure that the power socket in which you have plugged the
power cable of the DVD player is live by connecting another device to
it. If necessary plug the DVD players power cord into another power
socket.
Check to see that the display dimmer function is switched off.
To do this press the DIMMER button on the remote control.
Switch off the DVD player by activating the POWER switch and then wait
ten seconds. Then switch the DVD player back on by activating the POWER
switch again.
•
have connected the DVD player to a stereo television and have not
connected an audio component to the DVD player or
have connected a Dolby Prologic compatible audio component via the
analogue stereo outlet (via cinch cables to the cinch sockets L and R)
of the DVD player:
•
C
Check to see that you have selected in the OSD menu AUDIO with the
menu input FRONT SPEAKER the setting LARGE.
D
- 18 -
Download from Www.Somanuals.com. All Manuals Search And Download.
No 4:3 or 16:9 image
A
Check by means of the televisions operating instructions, which image
formats the television has at its disposal.
17. Glossary / Key Word Index
B
Check to see if the settings in the OSD menu match the available image
format of the television.
What are DVDs, VCDs and S-VCDs?
Remote control not functioning
DVDs
A
B
C
Check to make sure that the remote control batteries have been inserted
into the battery compartment with the correct polarity.
Check to see if the remote control batteries are exhausted and, if necessary,
change both batteries.
Make sure that there are no obstacles located between the remote control
and the DVD player.
DVD is the short form for "Digital Versatile Disc". DVDs are a storage medium
for audio and video data; they are available in 8 cm and 12 cm (Diameter)
formats. Because of the much higher storage capacity as compared to CD-Rs/
CD-RWs DVDs can provide a playback duration of up to eight hours for the
audio and video data stored on them.
D
Remain within five meters of the DVD player when using the remote control.
VCDs/S-VCDs
"Video CD" (VCD) and "Super Video CD" (S-VCD) are designations for two
processes of compressed storage, thus space saving, of films on CDs. VCDs
and S-VCDs are available in 8 cm and 12 cm (Diameter) formats. Their storage
capacity is a great deal lower than that of DVDs. For this reason they only
offer a playback duration, for the saved audio and video data on them, of
20 minutes (8 cm format) and/or 74 minutes (12 cm format).
VCDs are available in two versions:
Playback language/ Subtitle language do not correspond to the
settings in the OSD menu
The playback language/Subtitle language setting in the OSD menu is not
available on the inserted disc.
One or several functions can not be switched on
The selected functions may not be available on all DVDs/VCDs/S-VCDs!
•
Only audio and video data can be played back on version 1.1
If you attempt to execute a function that is not available, the symbol
displayed on the television screen.
is
VCDs/S-VCDs.
•
PBC (Playback control) functions are available on version 2.0 VCDs/
S-VCDs. In addition still images can be played back in a higher resolution.
None of the buttons on the device or on the remote control are
functioning/other malfunctions
Playback Control (PBC)
A
Switch off the DVD player by pressing the POWER switch. Wait ten seconds
and then activate the POWER switch again to switch the DVD player on
once more.
Version 2.0 VCDs/S-VCDs have Playback Control (in short "PBC") at their disposal.
Then on the VCD/S-VCD a main menu is available, by which various functions of
the VCD/S-VCD are allowed to be operated.
B
In the event that the malfunction is still present: Reset the DVD player to
its default settings.
What are Title and Chapter?
Title is the name given to the largest units of image and sound units on DVDs;
on many DVDs the (Main) film has the title number 01. For bonus material
(i.e. Film trailer, background information etc.), that is available on many DVDs,
other possible title numbers can be used.
For this see chapter 10.6 "Setup menu PREFERENCE".
Contact one of our service partners in your area if …
•
•
the stated function defect can not be resolved as described or
other functional defects arise.
Chapter is the name given to the next smaller image and sound units beneath
title. If the DVD/VCD/S-VCD or its title is divided into chapters, numbers are
assigned to you, through the input of which the chapter can be selected direct.
For this see chapter 18 "Warranty and service".
Bear in mind that not on all DVDs …
•
•
are the DVD or the title divided into (numbered) chapters
Chapters are also designated as "Scenes" (i.e. in the main menu of
DVDs)
What are Scart, S-Video, Composite-Video Progressive
Scan, YUV and HDMI?
Scart
Scart denotes a 21 pole standardized plug connection, via which the RGB
signal, video signal and S-Video signal as well as a number of control and
auxiliary signals are transmitted.
S-video
When the DVD player is connected to a television via S-Video the brightness
and colour signals are transmitted seperately; in this way a greater image
sharpness and a reduced so called "Colour noise" is achieved.
Colour noise refers to the overlaying of the colours, mostly heavily saturated
parts of a video image, through an irregular, restive breakdown structure.
- 19 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Composite video
Video signal or FBAS signal; thereby it involves an image signal, in which
colour and brightness information are included at the same time.
Dolby Prologic
In comparison to Dolby Surround sound format, with Dolby Prologic an additional
channel in the stereo signal is used; this is the so called "Centre" channel. The
corresponding centre loudspeaker is to be situated in the middle between the
stereo loudspeakers. The deepest sounds are fed to a bass loudspeaker, the
so called "Subwoofer". The subwoofer can be placed in any desired location
in the room; the logic for this is that the bass sounds that the subwoofer puts
out can scarcely be localized exactely by the human ear
Progressive scan
In the normal way TV devices and Video projectors are controlled with so
called "Half images". Thereby clearly visible line structures develop. Contrary
to this, Progressive Scan denotes the output of full images (with this DVD player,
at the output YPbPr) Progressive Scan signals can only be processed by play-
back devices equipped for this purpose (in particular large screen televisions
and projectors). The image quality as opposed to traditional image signals is
considerably higher.
Dolby Digital (5.1)
Dolby Digital, also designated as AC3, is a digital sound format, by which up
to six seperate audio channels can be transported. With most of the current
DVDs, the sound is stored in the so called "Dolby Digital 5.1" format; the "5"
in the name "5.1" stands for the three front and two rear surround sound
channels, the "1" stands for the subwoofer channel.
YUV (component video out)
YUV indicates the component signal, which with this device is available at the
output YPbPr in the form of so called "Half images"; as a rule this is the best
signal for the control of large screen televisions and projectors, which can not
process Progressive Scan signals. As with the RGB image transmission, YUV is DTS
comprised of three separated image signals: DTS is the abbreviation for "Digital Theatre System" and denotes one of the
•
•
the brightness signal "Y" and
the two colour diferential signals "U/Pb" and "V/Pr"
most common surround sound formats for DVDs. As with Dolby Digital 5.1,
DTS uses three front and two rear surround sound channels as well as a bass
sound channel.
Half images (Interlace)/Full images (Progressive Scan)
A standard television image is comprised of 576 visible lines; at first all odd
and then all even image lines are displayed alternatively, thus each displays
a half image. Thereby only 25 full images (50 Half images) can be displayed
per second. This technique is designated as "Interlace" format.
What are PAL and NTSC?
PAL
PAL is the abbreviation for "Phase Alternation Line". PAL is the mid and west
Europe (Exception: France) customary and widest distributed colour television
standard.
Contrary to this with the so called progressive or "Progressive Scan" format
all image lines are displayed every time, that is to say 60 full images per
second are displayed. Thereby increasing the total quality of the images, still
images and text for example appear sharper.
NTSC
NTSC is the abbreviation for "National Television System Committee". NTSC
is a colour television standard that is primarily used in the USA and Japan.
HDMI
HDMI is short for "High Definition Multimedia Interface" and refers to a 19
contact interface for complete digital transmission of audio and video data.
With its high bandwidth HDMI handles all known today home electronics
digital video and audio formats. HDMI transmits audio data up to frequencys
of 192 kHz with text widths of up to 24 Bit on up to 8 channels. Thus not
only all of today's image and sound formats introduced into home electronics
including HDTV (up to the highest present resolution of 1080p) are transmitted
without loss of quality but also future formats with yet higher resolutions.
Audio CDs
Audio CDs contain exclusively audio data; they are also available in 8 cm
and 12 cm (Diameter) formats. The playback duration for the audio data stored
on them amounts to 20 minutes (8 cm format) and/or 74 minutes (12 cm format).
Audio data is stored on audio CDs in CDA format.
MP3
MP3 denotes a process and/or format developed by the Fraunhofer Institute
for the compression of audio data. In the MP3 format compressed music pieces
are only a fraction of their original size, which, for example, on CD-Rs/CD-RWs
allows for storage of a considerably greater volume of music than on com-
mercially available audio CDs, on which audio data is stored in the CDA format.
Decoder
The sound on DVDs with home theatre sound is saved on the DVD in encrypted
(encoded) form. Different encryption formats exist for several purposes, for
example AC-3 for the playback of Dolby Digital Surround Sound.
In order to playback encrypted sound, the playback device (i.e. the DVD
player) and/or the audio component connected to it (for example Surround
system) must be equipped with a so called decoder, which converts the
encrypted signal back into music and/or sound.
WMA
WMA ("Windows® Media Audio") is a data format developed by Microsoft®
for audio data.
The Silvercrest KH 6523 DVD player is equipped with an AC-3 Decoder
(for Dolby Digital 5.1 Surround Sound signals).
JPEG
JPEG ("Joint Photographics Expert Group") denotes a wide spread graphic
format, developed by the organization with the same name, with which
image data of the colour and grey scales are compressed.
Dolby Surround
Dolby Surround is an analogue sound format, by which the two channels of
a stereo sound signal are used in order to accommodate room sound information
for further channels. Dolby Surround decoders convert the signals back into
sound or music and send the audio to two additional speakers that are situated
behind the listener.
- 20 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MPEG
MPEG ("Moving Picture Experts Group") refers to a video compression format.
What are folders?
As opposed to audio CDs the title on a CD-R/CD-RW with MP3, WMA or
JPEG files can be stored in folders, for example, in order to file titles from
different genres.
The structure of an MP3-CD can, for example, appear as follows, if the MP3
files are stored in folders:
FOLDER
MP3
MP3-CD
18. Warranty and Service
The warranty for this appliance is for 3 years from the date of purchase.
The appliance has been manufactured with care and meticulously examined
before delivery. Please retain your receipt as proof of purchase. In the event
of a warranty claim, please make contact by telephone with our Service
Department. Only in this way can a post-free despatch for your goods be
assured.
The warranty covers only claims for material and maufacturing defects, but
not for transport damage, for wearing parts or for damage to fragile compo-
nents, e.g. buttons or batteries. This product is for private use only and is not
intended for commercial use. The warranty is void in the case of abusive and
improper handling, use of force and internal tampering not carried out by our
authorized service branch. Your statutory rights are not restricted in any way
by this warranty.
The warranty period will not be extended by repairs made under warranty.
This applies also to replaced and repaired parts. Any damage and defects
extant on purchase must be reported immediately after unpacking the appli-
ance, at the latest, two days after the purchase date. Repairs made after the
expiration of the warranty period are subject to payment.
19. Importer
KOMPERNASS GMBH
BURGSTRASSE 21
D-44867 BOCHUM
- 21 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty
DVD Player KH6523
In order to guarantee a cost free repair procedure please
get in touch with the service hotline. Make sure you have
your sales slip handy.
DES UK LTD
Tel.: 0871 5000 700 (£ 0.10 / minute)
e-mail: [email protected]
Kompernass Service Ireland
Tel: 1850 930 412 (0,082 EUR/Min.)
Standard call rates apply. Mobile operators may vary.
e-mail: [email protected]
Sender, please write clearly:
Last name
First name
Street
City/Town
Country
Telephone
Date/Signature
Description of the defect:
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|