OPERATORS MANUAL
W20R
W10BT
WL83
W10BT BODY-PACK TRANSMITTER
RECEIVER
WL83 LAVALIER MICROPHONE
Download from Www.Somanuals.com. All Manuals Search And Download.
. . .
ON ACQUIRING ONE OF THE FINEST WIRELESS MICROPHONE SYSTEMS AVAILABLE TODAY. DESIGNED FOR
SIMPLE SETUP AND RELIABLE OPERATION, THIS SYSTEM SHOULD PROVIDE YEARS OF DEPENDABLE,
TROUBLE-FREE SERVICE. WE STRONGLY URGE THAT YOU READ THIS MANUAL; IT WILL SAVE YOU TIME AND EF-
FORT, AND ENSURE OPTIMUM SYSTEM OPERATION.
TABLE OF CONTENTS
The Wireless Microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
3
4
4
4
4
4
4
4
4
Frequency Bands
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Multiple Miking
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Directional Sensitivity
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Audio Performance
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
With the Transmitter Off
On Feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transmitter Range..
System Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
What Else is Needed..
5
6
W10BT Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
W20R Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setup and Connections
8
8
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
8
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
For Microphone Level Use
Transmitter.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
9
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Microphone Connections
Instrument Connections
9
9
Battery Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Polarity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting Gain Levels
10
10
10
10
11
12
13
13
13
13
14
15
16
17
17
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transmitter Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sound Pressure Levels
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Receiver Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Checklist/Operation
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications
Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transmitter
Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Receiver-Transmitter Distance
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Batteries
Troubleshooting
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessories
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FCC Certification
Warranty Service
Download from Www.Somanuals.com. All Manuals Search And Download.
THE WIRELESS MICROPHONE . . . what it is, what it does . . .
You’ve probably experienced this phenomenon with
the FM radio in your car. A dropout location, most likely
caused by buildings, mountains, or even telephone
poles, causes your radio signal to drop to a low, noisy
level -sometimes disappearing completely. This is
multipath.
The wireless microphone is actually a system consist-
ing of a microphone, a transmitter, and a receiver. The
microphone is an electroacoustic transducer-a device
which converts sound waves (voice, musical in-
struments, etc.) to electrical impulses, which are sent to
the transmitter. The transmitter generates a radio-
frequency carrier, modulates this carrier with the
microphone signals, and radiates this modulated RF
signal like a tiny radio station. The receiver is matched
to the transmitter frequency and picks up the transmitter
signal through its antenna. The receiver’s circuitry
detects the modulated RF signal and converts it to an
audio voltage for routing (through a microphone input) to
an audio mixer.
How can multipath be minimized? The following
general rules will help achieve optimum wireless
microphone operation:
l
Maintain line-of-sight transmission (the transmitter
wearer should always be able to see the receiver
antenna)
l
Keep the distance between transmitter and receiver
antenna as short as possible
At this point, the wireless system acts like any
microphone input to a sound system. The figure below
shows the complete system, including that which is not
a part of the wireless microphone system.
l
l
Avoid RF signal blocking by furniture, scenery, etc.
Make sure both transmitter and receiver antennas
are vertically positioned.
l
Don’t operate the transmitter with a weak or un-
suitable battery
Frequency Bands.....
Shure wireless transmitters and receivers are single-
channel, crystal-controlled units operating at selected
frequencies in the VHF-FM band between 150 and 186
megahertz. A total of 10 frequencies, computer-selected
for interference-free operation, are readily available, and
other frequencies can be ordered on a special basis.
This means that up to seven systems can be operated in
a single sound installation, simultaneously and without
intermodulation problems.*
Multiple Miking.....
More than one wireless microphone system can be
used in one sound installation, but each must operate at
a different frequency. Shure’s complement of 10 stan-
dard transmitter-receiver frequencies is generally suffi-
cient for any installation, but additional, special-order
frequencies can also be supplied for a nominal service
charge.
*If more than seven systems are contemplated, Shure recommends the use of
DIVERSIPHASE™ wireless microphone receivers.
Directional Sensitivity.....
The transmitter radiates omnidirectionally, that is, ap-
proximately equally in all directions. However, the signal
is attenuated by bodies, walls, and other surrounding ob-
jects. The receiving antenna is similarly sensitive to
radiation from all directions.
Multipath.....
The most troublesome aspect of wireless microphone
operation can be a phenomenon known as multipath
transmission, or simply, multipath. This appears as a
Audio Performance.....
with annoying static or complete
signal “dropout,”
Three important characteristics of high-fidelity audio
performance are wide frequency response, low distor-
tion and good signal-to-noise ratio. The Shure wireless
system uses high-quality FM circuitry for wide-range fre-
quency response. Distortion is kept to a minimum
(although temporary) signal loss. It’s caused when the
direct signal and a reflected signal-bounced off walls,
ceiling, metallic objects, etc.-arrive at the receiver at
different times, literally out-of-phase, or when the signal
path is completely unobstructed.
TYPICAL WIRELESS MICROPHONE SYSTEM
3
Download from Www.Somanuals.com. All Manuals Search And Download.
through the use of linear-phase IF filtering and high-
quality audio circuitry. A high signal-to-noise ratio and
wide dynamic range are necessary for noise-free, op-
timum performance. The Shure wireless uses com-
plementary compression and expansion circuitry in the
transmitter and receiver (companding) as well as pre-and
de-emphasis to achieve a maximum S/N ratio of 98 dB
A-weighted.
Reflections, obstacles and interference in a given in-
stallation will dictate the system’s limits.
Other wireless systems that claim greater distance
and flexibility in their operation neglect to state that
each installation must be considered separately. A wide
variance exists between best- and worst-case condi-
tions.
System Power.....
With the Transmitter Off.....
The receiver operates from power supplied by a
separate ac power converter provided with the system.
In addition to 120-volt operation with the power con-
verter, the receiver can be operated from any well-filtered
source of 13.5 Vdc at 200 mA. An optional 220-240-volt
power converter (WA350) is also available.
When the wireless microphone transmitter is turned
off, the receiver can still receive transmissions from
other sources. However, since the Shure system
operates in the 150-216 MHz band, it’s not susceptible to
interference from radio wave skip, or CB or FM broad-
cast transmissions. The frequencies chosen for use in
the Shure system are computer-selected for minimum in-
terference, but it’s almost impossible to guarantee a
“clear channel” at any location or at any time. (For in-
stance, care must be taken to avoid wireless microphone
operating frequencies that are within the bandwidth of
locally operating TV channels 7 through 13.)
The transmitter operates from any 9-volt alkaline
transistor-radio-type battery (Duracell MN1604 is recom-
mended). Typical battery life is 8 hours. Inexpensive
carbon-zinc batteries are not recommended; their ex-
tremely short life-about an hour- restricts them to
emergency use only. If nickel-cadmium rechargeable
batteries are used, they must be 8.4-volt (not 7.2-volt)
types. The lower-voltage batteries will not provide proper
transmitter function.
If the wireless system is to be in a permanent location,
it should operate without interference until someone
else in the vicinity starts using that frequency. But if the
system is to be used in different locations (i.e., “on the
road”), occasional frequency conflicts are inevitable. In
any case, if the wireless microphone is not in use, the
audio mixer gain should be turned down just as with a
wired microphone. If the mixer controls are not accessi-
ble, turn the receiver off when the transmitter is not in
use to prevent unwanted signal pickup. If the system
must be left on and mixer controls are not accessible,
the transmitter should be left on to prevent outside in-
terference pickup.
What Else is Needed.....
In order to make this wireless microphone system
operational, the following is needed:
A battery for the transmitter.
1.
2. A microphone for the transmitter-either one design-
ed specifically for the wireless transmitter (such as
or most low-impedance
the Shure WL83),
microphones (dynamic, ribbon or condenser) with a
microphone adapter cable (WA310). But if the
wireless system is to be connected to the electrical
output of a musical instrument instead of a
microphone, a transmitter instrument cable (WA300)
must be used.
On Feedback.....
The use of a wireless microphone doesn’t eliminate
the possibility of annoying feedback. Feedback control
is generally achieved by careful placement of the
speakers relative to the microphone, minimum levels
necessary for the desired sound, good microphone
technique, and proper equalization of the sound system.
A receiver-to-mixer cable, with a female XLR connec-
tor on one end (for the receiver output) and whatever
connector is needed for the mixer microphone input
on the other.
3.
Transmitter Range.....
Optional accessories, useful but not required, are
described in this manual.
The FCC-required low power output of the transmitter
means that its distance from the receiver should be kept
as short as possible. Up to 150 meters (500 feet) should
be considered a maximum, although 300-meter
(1000-foot) or greater operation is often accomplished.
*IMPORTANT: Other microphones specified as being for wireless microphone use
are probably not wired for use in Shure wireless systems. Condenser microphones
with phantom-powered preamp circuits
with this transmitter.
-
Shure SM85, SM87, etc.
-
will not operate
4
Download from Www.Somanuals.com. All Manuals Search And Download.
W10BT TRANSMITTER
the Low Gain position for high-output microphones or
musical instruments. Allows maximum modulation
without clipping.
ANTENNA: This is a flexible, 1/4-wave vertically
polarized antenna approximately 30 cm (12 in.) in length
and permanently attached to the bottom surface of the
transmitter. For proper operation, the antenna must be
in the vertical position; it cannot be coiled or bundled.
MICROPHONE JACK: This is a 4-pin, miniature, male
Tini Q-G connector designed to mate with Switchcraft
TA4F or equivalent connectors. A built-in 20-kilohm load
resistor provides proper matching for dynamic, ribbon or
condenser microphones. Connector pin 2 supplies
+5-volt bias voltage for condenser microphone phan-
tom powering. In addition to microphones with TA4F
connectors, Shure has available an adapter cable with a
standard XLR female connector for use with conven-
tional microphones (WA310), and a musical instrument
adapter cable with a 1/4-inch phone plug on the equip-
ment end (WA300).
BATTERY (not supplied): Only alkaline (Duracell
MN1604 or equivalent) or heavy-duty nickel-cadmium
(8.4-volt) transistor-radio-type batteries should be used.
A fresh alkaline battery should provide approximately 8
hours of operation, and a recharged nicad should pro-
vide 1-1/2 to 2 hours.
BATTERY COMPARTMENT: Slide the cover down to
expose the battery compartment. Make certain the bat-
tery is installed using the proper positive (+) and
negative (-) polarity.
MICROPHONE LEVEL Rotary Control: In conjunction
with the GAIN HI/LO switch, this control provides addi-
tional audio level adjustment. A small screwdriver is
supplied to make adjustments.
BATTERY TEST Push-Button Switch:
Permits checking
the condition of the installed battery when the power
switch is on. The BATTERY TEST LED Indicator will fail
to light if the battery is weak or dead (or if the POWER
switch is off). Note that if the battery is tested periodical-
ly during use, an impending battery failure can be
detected: the LED will fail to light at 7.25 volts. At that
time, approximately 1 hour of alkaline battery life is left.
MICROPHONE ON/OFF Toggle Switch: Permits the
user to “mute” the microphone without turning the
transmitter off. This avoids the “pop” that may accom-
pany power turn-on and turn-off, and generally prevents
pickup of unwanted signals by the receiver.
BELT CLIP: Permits convenient attachment to the
user’s belt, waistband or other clothing.
POWER ON/OFF Slide Switch: Applies power to the
transmitter circuitry. The switch is a low-profile type to
minimize accidental turn-off.
GAIN HI/LO Slide Switch: Selects the High Gain posi-
tion to boost the signal of low-output microphones, or
5
Download from Www.Somanuals.com. All Manuals Search And Download.
W20R RECEIVER
FRONT PANEL
RF SIGNAL LED Indicator: This yellow indicator lights
to show that the receiver is picking up the transmitted
signal. Note that the LED is not an indicator of signal
strength (the LED will light through a range of marginal
through strong signal conditions), but a flickering LED
generally indicates barely acceptable operation, and no
indication means that no signal is being received. The
receiver contains a squelch circuit to eliminate un-
wanted signals or noise in the absence of wireless
transmitter signals. The squelch circuit is not user-
adjustable; it is preset to an optimum threshold setting
of 1.0 µV, minimizing setting errors and difficulties in
returning the squelch to its original setting. The yellow
RF LED does not light when the squelch circuit is ac-
tivated.
POWER Push-Button Switch: Applies power from the
external power converter or other well-filtered 13.5 Vdc
(200 mA) sources to the receiver circuitry. An adjacent
green POWER LED Indicator remains on while power is
applied. (NOTE:
a 115 Vac, 60 Hz source, 13.5 Vdc is present at the power
converter output.)
With the power converter connected to
AUDIO LEVEL Display: This IO-LED bar display in-
dicates the relative system modulation. Normal opera-
tion is shown by illumination of the green portion of the
display, with occasional excursions into the yellow. If
frequent or constant yellow or red indications are
observed, the transmitter MICROPHONE LEVEL control
should be lowered (counterclockwise), or the Gain
switch set to the Lo position. The display is calibrated in
volume units (VU).
REAR PANEL
ANTENNA UHF-Type Connector: Provides for connec-
Download from Www.Somanuals.com. All Manuals Search And Download.
6
POWER 13.5 VDC NEGATIVE GROUND Coaxial
Jack: This connector accepts power from the supplied
power converter, or from any well-filtered 13.5 Vdc (200
mA) supply.
tion to the 1/4-wave vertical antenna supplied with the
W20R (or the optional WA250 5/8-wave antenna, which
provides up to 3 dB additional RF gain). If the receiver is
to be mounted in a shielded rack mount enclosure or
other area which may interfere with RF wave reception,
the 7.6m (25 ft) coaxial cable (WA280) permits remote
antenna placement, and the WA250 can be attached to a
microphone stand or wall mounted using the optional
bracket (WA260). (NOTE: Remote placement of the
1/4-wave antenna using the WA280 coaxial cable re-
quires a female-to-female PL258-type UHF adapter.)
MIC OUTPUT 3-Pin XLR Connector: Provides balanced,
low-impedance output for connection to the audio mixer
or amplifier.
INTERNAL
For access to the internal power fuse, remove four
screws at the sides, and two at the top front and rear.
FUSE 1/2A: This is a 0.5 ampere, 250-volt, 3AG-type,
fast-blow fuse that protects the power supply from ex-
cessive current. It should be replaced only with a fuse of
identical size and value (Littelfuse 312.500 or
equivalent).
MICROPHONE OUTPUT LEVEL Rotary Control: This
control determines the signal level at the OUTPUT Con-
nector. Using this control, the signal level can be match-
ed to that of a conventional wired microphone.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP AND CONNECTIONS
equivalent) in the compartment. Observe the proper
polarity: the large (negative) terminal in the large chan-
nel and the small (positive) terminal in the small channel.
Operation with a full charged, heavy-duty, 8.4-volt nickel-
cadmium rechargeable battery is also permissible.
UNPACKING
Unpack all units and parts of the Wireless Microphone
System. If possible, retain packaging in the event of
returning a unit for repair. Check all boxes and inner
packaging; if any damage or shortage is discovered,
refer to the Warranty Service section of this manual.
IMPORTANT:
Do not use a “conventional” 9-volt-sized
nickel-cadmium battery; its 7.2-volt output will operate
the transmitter for about 15 minutes. Carbon-zinc bat-
teries will also result in diminished operating life (about
1 hour).
RECEIVER
Place the W20R receiver in its operating location and
connect the supplied power converter to the rear-panel
POWER Jack. Connect the power converter to a 105 to
125 Vac, 60 Hz power source.
Microphone Connections
The Shure WL83 lavalier condenser microphone or
similar microphones with identical wiring and a Switch-
craft TA4F type connector can be plugged directly into
the transmitter microphone jack. The WL83 will operate
using the transmitter’s regulated +5 Vdc available on
pin 2 (see Figure 2). Self-powered (battery) condenser
microphones can be used with the transmitter only if
they can be operated in an unbalanced mode (one side
grounded). Other non-self-powered condenser
microphones may require special wiring; contact
Shure’s Service Department for further information.
Phantom-powered condenser microphones will not
operate with the W10BT.
Attach the 1/4-wave whip antenna to the receiver
ANTENNA connector. Make certain it is pointed upward.
IMPORTANT: The receiver antenna should be within
the line-of-sight of the transmitter’s operating area.
Obstructing or reflecting objects will degrade wireless
microphone performance.
If desired, the receiver can be mounted in a rack panel
kit (WA210) for mounting in a standard 19-inch audio
equipment rack.
For Microphone Level Use
Obtain an XLR-type balanced low-impedance audio
connecting cable and connect it between the W20R MIC
OUTPUT Connector and the mixer or amplifier
microphone-level input (see Figure 1). Adjust the levels
as described under Level Adjustment.
A high- or low-impedance dynamic or ribbon
microphone with pin 2 output can be directly connected
to the transmitter using the supplied WA310 microphone
adapter cable. The cable has a 3-socket XLR connector
on the microphone end and a Switchcraft TA4F connec-
tor on the transmitter end, and is wired for unbalanced
low-impedance operation only (see Figure 2). Shure high-
impedance microphones are not wired to operate with
the transmitter. If a Shure high-impedance microphone
must be used, pins 2 and 3 should be reversed (by
qualified service personnel). Using a low-output, low-
impedance dynamic lavalier microphone such as
Shure’s SM11 may require raising the mixer input gain
appreciably, which in turn may result in an increase in
noise and signal “pumping.”
Instrument Connections
To connect the transmitter to a guitar or other musical
instrument pickup, obtain an instrument adapter cable
such as Shure’s WA300. This cable has a 1/4-inch phone
plug on one end and a Switchcraft TA4F on the other
(see Figure 2), and should function normally with any
high-impedance instrument pickup.
RECEIVER-MIXER CABLE
FIGURE 1
Battery Check
TRANSMITTER
Turn the transmitter power on and depress the BAT-
TERY TEST Switch. The adjacent LED should light, in-
dicating adequate transmitter input voltage. If the LED
does not light, the alkaline battery voltage has dropped
With the transmitter POWER ON/OFF Switch in the
OFF position, slide the battery compartment access
cover down and off the transmitter case. Insert a new
9-volt transistor-radio-type battery (Duracell MN1604 or
8
Download from Www.Somanuals.com. All Manuals Search And Download.
below 7.25 volts and the battery should be replaced or
recharged (nicad only).
If the battery is tested periodically, the failure of the
LED to light indicates approximately one hour-of battery
life left (alkaline only).
Polarity
With the Shure WL83 or a Shure low- or high-
impedance XLR-connector microphone connected
through a WA310 cable, positive pressure on the
microphone diaphragm results in positive voltage on pin
2 with respect to pin 3 of the receiver OUTPUT connec-
tor. Negative voltage applied to the tip of a WA300 cable
will result in the same output polarity.
TRANSMITTER CONNECTIONS AND
ACCESSORY WIRING
FIGURE 2
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING GAIN LEVELS
With the system in place and connected, all units can
now be turned on and the levels set to their optimum
positions.
TRANSMITTER
Place the POWER Switch of the W20R receiver in the
ON position. The green POWER LED will light.
Turn the transmitter POWER ON/OFF Switch on.
Observe the receiver yellow RF SIGNAL LED. It should
be continually lit, indicating adequate RF signal
strength for good transmission. If the LED continually
flickers or does not light, consult the Troubleshooting
section of this manual.
Turn the transmitter MIC ON/OFF Switch to the ON
position. With a microphone connected to the transmit-
ter, the receiver AUDIO LEVEL display will now respond
to varying sound levels.
Set the transmitter GAIN Switch as dictated by the
type of input: Hi for low-impedance microphones; LO
for high-impedance microphones and instrument
pickups.
HIGH SPL GAIN ADJUSTMENT
FIGURE 4
may require an increase in the transmitter gain setting.
To correct for a low-level condition, turn the MIC LEVEL
Control up (clockwise; see Figure 5) until a proper (-7 to
0) LED reading is obtained.
Sound Pressure Levels
Normal. The transmitter MIC LEVEL Control has been
factory-set to provide optimum audio modulation at the
receiver, as indicated by LED illumination in the -7 to 0
range (see Figure 3). Readings in this area will yield the
highest dynamic range without overload and resulting
distortion.
AUDIO LEVEL DISPLAY
FIGURE 3
High. For high sound pressure level (SPL) applications
such as loud singing or musical instruments, the preset
transmitter level may be too high. To avoid this overload
and potential distortion condition, use the supplied
screwdriver to turn the transmitter MIC LEVEL Control
down (counterclockwise; see Figure 4). This adjustment
should be made under the expected operating condi-
tions, that is, with the high SPL singer or musical instru-
ment in use at the microphone. Turn the control down
until the optimum (-7 to 0) readings are obtained.
LOW SPL GAIN ADJUSTMENT
FIGURE 5
RECEIVER
The rear-panel receiver OUTPUT can be adjusted using
the MICROPHONE OUTPUT LEVEL Control. In this way,
the wireless system output can be made identical to that
of a conventional wired microphone, avoiding extreme
differences in input level settings. Turning the
MICROPHONE OUTPUT LEVEL Control counter-
clockwise decreases the output level, and turning it
clockwise increases the output.
Low. Low SPL applications such as soft-spoken in-
dividuals or conditions where the microphone must be at
a greater-than-normal distance from the sound source,
10
Download from Www.Somanuals.com. All Manuals Search And Download.
CHECKLIST/OPERATION
CHECKLIST
3. Talk into the microphone (or play the connected
musical instrument) and observe the receiver
display for proper audio and RF indications.
The following checklist shows the status of your
wireless microphone system at this point. If the follow-
ing steps have been performed and the expected results
obtained, the system can be put in operation.
4. Continue talking or playing and move around the
performing area. In each area, observe the receiver
displays and make sure the RF signal strength is
adequate.
Is the receiver properly located?
o
Is the power converter connected to the receiver? Is
ac power present?
o
In most cases, the problem of weak RF signal strength
o Is the antenna connected to the receiver?
is also indicated by audible evidence:
signal dropout,
either continuous or intermittent, or noisy, distorted
operation. The condition is generally caused by poor
antenna location, RF signal blocking, or operation
b e y o n d t h e s y s t e m c a p a b i l i t y . R e f e r t o t h e
Troubleshooting section for remedies.
o
Is the receiver connected to the rest of the sound
system?
o
Is a fresh battery installed in the transmitter?
o Is a microphone of the proper impedance and wiring
being used?
Normal operation is shown by steady illumination of
the yellow RF SIGNAL LED. A weak RF signal is in-
dicated by intermittent lighting of the LED, as well as by
audibly poor sound quality.
Is the microphone or instrument connected to the
transmitter?
o
o Has the transmitter gain been set properly?
Feedback-the annoying howl or squeal heard in the
sound system- is as much a problem in wireless
microphones as in wired mics. Checking microphone
operation throughout the performing area will probably
uncover any locations that are prone to audio feedback.
If the problem cannot be solved by a slight lowering of
the receiver output level or the associated amplifier gain,
relocation of the speakers or possibly professional
equalization of the sound system is recommended.
o
Have the transmitter and transmitter antenna been
properly positioned?
o
Is the receiver output level properly set?
OPERATION
Turn on the transmitter and receiver POWER
Switches.
1.
2.
Make sure the transmitter MIC ON/OFF Switch is on.
IMPORTANT
Every wireless microphone installation is a unique
situation, and can present a variety of problems.
Never attempt a live performance without a
“walkthrough” first. And if major changes (fur-
niture, scenery, etc.) were made since the
walkthrough, check the wireless microphone
operation again.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
SYSTEM
Antenna Input Impedance
50 ohms nominal
RF Carrier Frequency
Antenna
150 to 216 MHz (10 frequencies between 167.875 and
183.0 MHz offered; others available)
1/4 wavelength, 457 mm (18 in.) whip, UHF connector
Power
Frequency Stability
13.5 Vdc nominal (negative ground); 200 mA external
power converter supplied
0.005%, Crystal-Controlled
Ultimate Quieting (ref. 12 kHz deviation)
>90 dB at 30m (100 ft); 60 dB, line-of-sight at 402m
(1/4 mi.)
Dimensions
42.8 mm H (plus feet) x 190 mm W x 173 mm D (1-11/16
in. x 7-1/2 in. x 6-13/16 in.) (depth is 190 mm–7-1/2 in.
including controls and connectors)
Modulation
± 12 kHz deviation compressor-expander system with
pre- and de-emphasis
Weight
723 grams (1 lb 9-1/2 oz)
Distortion (ref. 12 kHz deviation)
Less than 0.3% THD, 50-15,000 Hz
TRANSMITTER
Dynamic Range
98 dB A-weighted
92 dB unweighted
RF Power Output
50 mW maximum; 30 mW typical
Modulation
Audio Frequency Response
54F3 ± 12 kHz deviation, 50 µsec pre-emphasis
50 to 15,000 Hz, ± 1 dB
Modulation Limiter
Audio Polarity
internal compressor
Positive pressure on microphone diaphragm results
in positive voltage on pin 2 with respect to pin 3 of
OUTPUT connector (with Shure WL83 or Shure low- or
high-impedance, XLR-connector microphone through
WA310 cable); negative voltage applied to tip of
WA300 cable connector results in same output polari-
Input Impedance
16k (20k dc), pin 4 wired to pin 3 for WL83
Actual:
microphone; 91k, pin 4 open for microphone or instru-
ment pickup
Gain Switch
0.0065 Vrms required for
100% modulation
0.065 Vrms required for
100% modulation
High position . . . . . . . .
Low position . . . . . . . . .
Gain Adjustment Range
ty
Temperature Range
- 18° to 54°C (0° to 130°F)
Receiver . . . . . . . . . . . .
Transmitter (alkaline batt.) . 0° to 38°C (32° to 100oF)
Transmitter (mercury batt.) 4° to 54°C (40° to 130°F)
.
Low Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 dB
High Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 dB
Transmitter (carbon-zinc) . . . 7° to 32°C (45° to 90°F)
Certification
Antenna
Type-accepted under FCC Parts 90 and 74
(FCC ID DD48NJW20R)
Attached, 305 mm (12 in.), omnidirectional, flexible
wire
RECEIVER
Power
9 - v o l t a l k a l i n e ( N E D A
1604A); 8.4-volt nicad op-
tional
Battery Type . . . . . . . . .
RF Sensitivity
Less than 0.5 µV for 12 dB SINAD
Image Rejection
Battery Life . . . . . . . . . . 6
to
8
hours
typical
At least 75 dB
(alkaline); 1.5 to 2 hours
typical (8.4-volt nicad; per
charge)
Spurious Rejection
At least 80 dB
Current Drain . . . . . . . . 35 mA typical
Squelch Quieting
Dimensions
125 dB
102 mm H x 69.8 mm W x 25.4 mm D (4 in. x 2-3/4 in. x 1
in.) (not including antenna, controls and belt clip)
Squelch Threshold
Internally preset to 1.0 µV
Weight
Output
113 grams (4 oz); 170 grams (6 oz) with battery
-20 dB across 200 ohms maximum (mic level ad-
justable)
Download from Www.Somanuals.com. All Manuals Search And Download.
12
ANTENNAS
TRANSMITTER
The transmitter antenna is a permanently attached,
flexible wire, 1/4-wave antenna. It has an omnidirectional
transmission pattern (equally effective in all directions)
and is designed to operate in a vertically polarized mode.
This means that the antenna should hang downward dur-
ing operation; coiling or wadding it to minimize visibility
will reduce the system’s operating distance.
RECEIVER
The receiver antenna is a single-section, 1/4-wave
whip antenna approximately 457 mm (18 in.) in length.
Like the transmitter antenna, the receiver antenna has
an omnidirectional pickup pattern and are vertically
polarized. Vertical mounting is a requirement for op-
timum pickup.
TRANSMITTER-RECEIVER DISTANCE
FIGURE 6
installations, improved performance
For “problem”
may be obtained using an optional 5/8-wave whip anten-
na (WA250). Up to 3 dB gain increase can be realized with
this antenna over the standard 1/4-wave.
Also available for use with the 5/8-wave antenna are a
7.6m (25 ft) coaxial cable (WA280) for remotely locating
the antenna (necessary where the receiver is to be
mounted in a shielded rack mount enclosure or other
poor RF location), and a wall-mount bracket (WA260) for
affixing the antenna to a variety of surfaces. The
5/8-wave antenna can also be mounted on a conven-
tional microphone stand using a microphone swivel
adapter such a the Shure A25B or A25C.
LINE-OF-SIGHT TRANSMISSION
FIGURE 7
RECEIVER-TRANSMITTER DISTANCE
Observing the following rules regarding transmitter to
receiver antenna distance will yield the best results
possible.
Keep the transmitter to receiver antenna distance as
short as possible. As the distance increases, the
transmitted signal is weaker (see Figure 6).
Make certain the signal path between the transmitter
and the receiver antenna is unobstructed. The
transmitter wearer should be able to visually locate
the receiver antenna at any time (see Figure 7).
Try to avoid operating the system through or around
walls, ceilings, metal objects, etc. The usual result is
reduced range and performance, and the signal
reflections off metal obstructions will not only cause
reduced signal, but will introduce the problem of
multipath distortion (see Figure 8).
OBSTRUCTION EFFECTS
FIGURE 8
13
Download from Www.Somanuals.com. All Manuals Search And Download.
BATTERIES
The battery should be removed if the transmitter
malfunctions, or if it is to be stored for a long period.
Most batteries have a protective jacket, but partly or
completely exhausted batteries are more prone to
leakage.
Careful transmitter battery selection, installation, use
and care will help avoid problems in wireless
microphone use. The most dependable, long-lived bat-
teries at this time are the manganese-alkaline, or
alkaline, types. In addition to offering the longest ex-
pected operating life, they are commonly available.
Do not attempt to recharge replaceable (primary) bat-
teries using “chargers”, heat or other methods. This may
cause leakage or explosion. Do not disassemble bat-
teries or dispose of them in fire.
One small word of caution about alkaline batteries:
they are not all the same size. Make certain the battery
you buy will make contact inside the battery compart-
ment.
Nickel-cadmium (nicad) batteries can save money
through their rechargeability, but the tradeoff is in
shorter expected life per charge. In addition, forgetting
to recharge can be disastrous.
MANUFACTURER
VOLTS
& NO.
EXPECTED LIFE
BATTERY TYPE
6 to 7 hours
Alkaline
Bright Star 7590
Duracell MN1604
ESB A1604
Eveready 522
IEC 6LF22
NEDA 1604A
Panasonic 6AM6
Radio Shack
23-553
Ray-O-Vac A1604
U.S. Military
BA3090
9.0
Another major consideration in nicads is that of
operating voltage. The “heavy-duty” 8.4-volt nicads are
satisfactory for transmitter use, but the “9-volt-size”
nicads commonly found in stores are only 7.2 volts and
will not provide satisfactory wireless performance.
Mercury batteries in the “g-volt-size” are also actually
8.4 volts. However, their discharge characteristics are
such that they will yield between 10 and 15 hours of
operation with the transmitter.
Varta 4022
Carbon-zinc batteries are the least useful for transmit-
ter operation. Their low cost is more than offset by their
extremely short operating and shelf life. Although the
“heavy-duty”’ (HD) carbon-zinc types offer better low-
temperature performance and service capacity at
moderate to high current drain, they will not offer ap-
preciably better transmitter performance than standard
carbon-zinc batteries.
Burgess H146X
Duracell TR146X
Eveready E146X
NEDA 1604M
Panasonic TR146
US. Military
8.4
10 to 15 hours
Mercury
BA1090/U
Although battery operation is inhibited at low
temperatures, storing batteries at low temperatures will
increase their shelf life. They should be sealed in bags
and, when ready for use, allow to warm up to room
temperature (never heated!). Cold-stored batteries
should be used as soon as possible after bringing to
room temperature.
Nickel-Cadmium
SAFT PS-9
Varta TR7/8
8.4
9.0
1-1/2 to 2 hours
per charge
1 hour
Duracell M1604
Eveready 216
Ray-O-Vac 1604
Radio Shack
23-464
Battery life is shortened by high-temperature storage
such as on amplifiers or in vehicles exposed to direct
sunlight.
1 hour
Carbon-Zinc
(Heavy Duty)
Duracell
M1604HD
Eveready 1222
Ray-O-Vac D1604
Radio Shack
23-583
9.0
RECOMMENDED RANGES
Carbon-
Zinc
Alkaline
Mercury
Nicad
-20° to 45°C
4° to 54°C
7° to 32°C
Temperature
0° to 38°C
(40° to 130°F) (45° to 90°F)
(32° to 100°F)
(-4° to 113°F)
10 to 80 days
Shelf Life (room
temperature; to
80% of capacity)
30 months
30 months
6 to 12
months
14
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
If you encounter any problems in the operation of your Shure Wireless Microphone System, first make certain
you’ve followed the ABC’s of proper wireless microphone operation:
Make certain the transmitter antenna is dangling vertically. Make certain the receiver antenna is
properly connected, located and mounted.
A
ntennas -
Battery -
ontrols -
Make certain the transmitter battery is fresh and of the right type. And while you’re at it, make cer-
tain the receiver power converter is connected to a functioning power source.
C
All receiver and transmitter controls should be properly set for the desired operation. Recheck all
settings for correct system setup.
If you still have a problem, follow the advice below. If you’re unable to solve the problem, contact your dealer or
Shure’s Service Department.
SOLUTION
PROBLEM
Make certain the antenna is properly connected,
mounted and positioned for optimum reception. Mini-
mize transmitter-to-receiver distance.
Movement around the performing area produces
intermittent “swooshing” sound or complete loss of
signal (dropout).
Audio signal sounds distorted at medium to high
input levels.
Reduce transmitter audio gain.
Receiver picks up other (interfering) radio signals.
Make certain transmitter is turned on. If problem per-
sists with transmitter on, it may be necessary to
change system operating frequency. (Another
transmitter, possibly a VHF-TV transmitter, may be
operating at the same frequency.)
Audio signal contains undesirable whistling or
chirping sounds, or sounds garbled.
Two transmitters may be operating simultaneously
on the same frequency. Turn one transmitter off. If
problem persists, may be caused by other radio
signals (see above).
Audio signal contains undesirable hissing sounds.
Transmitter and/or receiver gain may require
increase (setting is too low).
One wireless microphone produces a lower output
than other wireless microphones in the same sound
system.
Movement around the performing area produces an
undesirable squeal or howl (feedback).
Relocate the speakers. Reduce the receiver and/or
and/or sound system gain. (Professional equalization
may be required.)
Maximum operating distance (transmitter to receiver
antenna) seems less than when system was new.
Transmitter antenna may require replacement.
Receiver antenna may require relocation.
Short transmitter battery life.
Make certain replaceable batteries are alkaline
(Duracell MN1604 or equivalent). Make certain
rechargeable batteries (nicads) are 8.4-volt types.
Receiver not functioning.
Make certain receiver power converter is connected
to functioning ac source.
Make certain internal 0.5A, 250V, 3AG fuse is not
blown. (Disconnect from ac source, remove four side,
two front and two back screws for access to fuse.)
Many apparent problems are due to improper setup and operation. Make certain you have followed
REMEMBER:
instructions carefully before contacting Shure for service.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCESSORIES
The following Shure Wireless System accessories are
available through your Shure dealer. (Replacement parts
can be ordered from Shure’s Service Department; infor-
mation is available from Shure’s Service Department.)
1/4-wave or the optional 5/8-wave receiver antenna to
locate the antenna at a distance from the receiver.
MODEL WA300 INSTRUMENT CABLE – This is a 1.2m (4
ft), single-conductor, shielded cable with a 1/4-inch
phone plug on one end and a Switchcraft TA4F on the
other. It is used for connecting the W10BT transmitter to
a guitar or other musical instrument pickup.
MODEL WL83 LAVALIER CONDENSER MICROPHONE
– This is a tiny electret condenser microphone design-
ed for high-quality sound reproduction in broadcasting,
film and sound reinforcement applications. The WL83
plugs directly into the W10BT transmitter, and is sup-
plied with a variety of mounting options.
MODEL WA310 MICROPHONE CABLE – A 1.2m (4 ft),
single-conductor, shielded cable with a 3-socket (female)
XLR connector on one end and a Switchcraft TA4F on
the other. The WA310 is designed to connect the W10BT
to a low-impedance dynamic or condenser microphone
for unbalanced operation (pin 3 of the XLR connector is
“hot”).
MODEL WA200 SINGLE RECEIVER RACK MOUNT KIT
– This kit consists of a metal front panel and hardware
for mounting one W20R receiver in a standard 19-in (483
mm) audio equipment rack.
MODEL WA320 AC POWER CONVERTER – This is a
replacement for the 120 Vac power converter supplied
with the W20R receiver.
MODEL WA210 DOUBLE RECEIVER RACK MOUNT KIT
– Similar to the WA200, this kit permits mounting two
W20R receivers side by side in a standard 44.5 mm x 483
mm (1-3/4 x 19 in.) rack space.
MODEL WA330 MICROPHONE CONNECTOR – This
TA4F miniature connector permits microphones such as
the Shure SM10A or SM98 to be connected directly to the
W10BT transmitter.
MODEL WA250 5/8-WAVE WHIP ANTENNA – This
3-section whip antenna is an optional replacement for
the 1/4-wave antenna supplied with the W20R receiver. It
comes with a right-angle UHF adapter.
MODEL WA340 1/4-WAVE WHIP ANTENNA – This is a
replacement for the 1/4-wave whip antenna supplied with
the W20R receiver.
MODEL WA260 ANTENNA WALL-MOUNT BRACKET –
This bracket is for use with the optional 5/8-wave anten-
na. It comes with mounting hardware.
MODEL WA350 AC POWER CONVERTER – Similar to
the WA320, this power converter permits operation at
220 to 240 Vac.
MODEL WA280 COAXIAL ANTENNA CABLE – This
7.6m (25 ft) coaxial cable can be used with either the
16
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC CERTIFICATION
quency. Shure strongly urges the user to contact the ap-
propriate telecommunications authority before choos-
ing an ordering frequencies other than factory-preset fre-
quencies. This recommendation applies to both original
equipment purchase and subsequent frequency
modification by Shure.
The Shure Model W10BT transmitter is Type-Accepted
under Federal Communications Commission Parts 90
and 74. The Shure Model W20R receiver is Type-
Accepted under FCC Part 15. Licensing of Shure
wireless microphone equipment is the user’s respon-
sibility, and licensability depends on the user’s
classification and application, and on the selected fre-
WARRANTY SERVICE
If you are requested to return the equipment by
Shure’s Service Department, package the unit (with all
information requested) as follows: Check to see that
all parts are present and in place. If the original carton is
not available, place the unit in a strong shipping carton
at least 13 mm (6 in.) large in all three dimensions than
the unit. Fill the surrounding space with a resilient pack-
ing material such as shredded paper, excelsior,
Styrofoam, etc. Seal the carton with gummed paper tape,
tie it with a strong cord, and ship it prepaid to the Shure
Service Department.
If your Shure wireless microphone equipment should
require servicing under the Shure warranty, please con-
tact:
Shure Brothers Inc.
Attention: Service Department
222 Hartrey Avenue
Evanston, Illinois 60202-3696 U.S.A.
Telephone: (312) 866-5730
All claims of defects or shortage should be directed to
the above address. Please furnish model number,
operating frequency, and date, place and proof of pur-
chase (such as a copy of the sales receipt) to establish
warranty. Your letter should include all pertinent details
including applicable model or part numbers and a brief
description of the problem. Do not return any units or
parts to Shure unless requested to do so by Shure’s Ser-
vice Department. Any returned items must have prior
authorization. Unauthorized returns are delayed in
handling; these delays can be avoided by contacting
Shure in advance and furnishing the necessary informa-
tion.
It is extremely important that the packaged unit be
well-packed and fully insured. Damage claims are sub-
ject to settlement between the shipper and the carrier,
and this can delay repair and return of the unit.
Shure reserves the right to make design changes and
product improvements without assuming any obligation
to install these changes or improvements on any
previously manufactured products. Shure also reserves
the right to ship new and/or improved products which are
similar to the form, fit and function of the originally
ordered products.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
222 HARTREY AVENUE, EVANSTON, ILLINOIS 60202-3696 U.S.A.
l
TELEPHONE: (312)866-2200
l
CABLE: SHUREMlCRO
Copyright 1986, Shure Brothers Inc.
27A2314 (FL)
Download from Www.Somanuals.com. All Manuals Search And Download.
Printed in U.S.A.
|