-
XV Z9000E
PROJECTOR
PROJEKTOR
PROJECTEUR
PROJEKTOR
PROYECTOR
PROIETTORE
PROJECTOR
OPERATION MANUAL
BEDIENUNGSANLEITUNG
MODE D’EMPLOI
BRUKSANVISNING
MANUAL DE MANEJO
MANUALE DI ISTRUZIONI
GEBRUIKSAANWIJZING
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using the projector, please read this operation manual carefully.
OPERATION MANUAL
ENGLISH
IMPORTANT
For your assistance in reporting the loss or theft of your
-
Model No.: XV Z9000E
Projector, please record the Serial Number located on
the bottom of the projector and retain this information.
Before recycling the packaging, please be sure that
you have checked the contents of the carton thoroughly
against the list of “Supplied Accessories” on page 12.
Serial No.:
WARNING:
Intense light source. Do not look into the beam or view it directly. Be especially careful that children do not look
directly into the beam.
WARNING:
To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.
CAUTION:
To reduce the risk of electric shock, do not remove cabinet. No user-serviceable parts are inside. Refer servicing
to qualified service personnel.
WARNING:
The cooling fan in this projector continues to run for about 90 seconds after the projector is turned off. During
normal operation, when turning the power off always use the OFF button on the projector or on the remote
control. Ensure the cooling fan has stopped before disconnecting the power cord.
DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING THE POWER
CORD. FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Caution Concerning the Lamp Replacement
See “Replacing the Lamp” on page 47.
USER SERVICE SCREWS
VIS POUR ENTRETIEN PAR L’UTILISATEUR
PRECAUTIONS A OBSERVER LORS DU
LAMP REPLACEMENT
CAUTION
REMPLACEMENT DE LA LAMPE.
BEFORE REMOVING THE SCREW, DISCONNECT
POWER CORD. HOT SURFACE INSIDE.
ALLOW 1 HOUR TO COOL BEFORE REPLACING
THE LAMP. REPLACE WITH SAME SHARP LAMP
UNIT TYPE BQC-XVZ9000/1ONLY.
DEBRANCHER LE CORDON D’ALIMENTATION AVANT DE RETIRER LES VIS.
L’INTERIEUR DU BOITIERETANT EXTREMEMENT CHAUD, ATTENDRE1HEURE
AVANT DE PROCEDER AU REMPLACEMENTDE LA LAMPE.
NE REMPLACER QUE PAR UNE LAMPE SHARP DE TYPEBQC-XVZ9000/1.
RAYONS ULTRAVIOLETS : PEUVENT ENDOMMAGER LES YEUX.
ETEINDRE LA LAMPE AVANT DE PROCEDERA L’ENTRETIEN.
LAMPE A MOYENNE PRESSION: RISQUED’EXPLOSION. DANGERPOTENTIEL
DE PARTICULES DE VERRE EN CAS D’ECLATEMENT DE LA LAMPE.
A MANIPULER AVEC PRECAUTION, SE REPORTER AU MODE D’EMPLOI.
UV RADIATION : CAN CAUSE EYE DAMAGE.
TURN OFF LAMP BEFORE SERVICING.
MEDIUM PRESSURE LAMP : RISK OF EXPLOSION.
POTENTIAL HAZARD OF GLASS PARTICLES IF
LAMP HAS RUPTURED. HANDLE WITH CARE.
SEE OPERATION MANUAL.
WARNING:
Some IC chips in this product include confidential and/or trade secret property belonging to Texas Instruments.
Therefore you may not copy, modify, adapt, translate, distribute, reverse engineer, reverse assemble or discompile
the contents thereof.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFEGUARDS
ATTENTION: Please read all of these instructions before you operate your Projector for
the first time. Save these instructions for future reference.
For your own protection and prolonged operation of your Projector, be sure to read the following “IMPORTANT
SAFEGUARDS” carefully, before use.
This projector has been engineered and manufactured to ensure your personal safety. But IMPROPER USE CAN
RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the safeguards
incorporated into this Projector, observe the following basic rules for its installation, use and servicing.
1. Unplug the Projector from the wall outlet before cleaning.
2. Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.
3. Do not use attachments not recommended by the
Projector manufacturer, as they may cause hazards.
4. Do not use the Projector near water; for example, near a
bathtub, washbowl, kitchen sink, laundry tub, in a wet
basement, near a swimming pool, etc. Never spill liquid
into the projector.
5. Do not place the Projector on an unstable cart, stand, or
table. The Projector may fall, which may cause serious
injury to a child or an adult, and/or serious damage to the
unit.
17. Unplug the Projector equipment from the wall outlet and
refer servicing to qualified service personnel under the
following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the Projector.
c. If the Projector has been exposed to rain or water.
d. If the Projector does not operate normally when
you follow the operating instructions. Adjust only
those controls that are covered by the operating
instructions, as improper adjustment of other
controls may cause damage and will often require
extensive work by a qualified technician to restore
the Projector to normal operation.
6. Wall or Ceiling Mounting—The product should be
mounted to a wall or ceiling only as recommended by
the manufacturer.
e. If the Projector has been dropped or the cabinet
has been damaged.
f. When the Projector exhibits a distinct change in
performance—this indicates a need for service.
18. When replacement parts are required, be sure the ser-
vice technician has used replacement parts specified by
the manufacturer that have the same characteristics as
the original parts. Unauthorised substitutions may result
in fire, electric shock, or other hazards.
7. Projector equipment and cart
combinations should be moved
with care. Quick stops, excessive
force, and uneven surfaces may
cause the equipment and cart
combination to overturn.
8. Slots and openings in the cabinet back and bottom are
provided for ventilation. To ensure reliable operation of
the Projector and to protect it from overheating, these
openings must not be blocked or covered. The openings
should never be covered with cloth or other material.
9. This Projector should never be placed near or over a
radiator or heating vent. The Projector should not be
placed in a built-in installation such as a bookcase unless
proper ventilation is provided.
19. This Projector is provided with one of the following types
of plugs. If the plug should fail to fit into the power outlet,
please contact your electrician.
Do not defeat the safety purpose of the plug.
a. Two-wire type mains plug.
b. Three-wire grounding type mains plug with a
grounding terminal.
This plug will only fit into a grounding type power
outlet.
10. The Projector should be operated only from the type of
power source indicated on the back of the projector or in
the specifications. If you are not sure of the type of power
supplied to your home, consult your Projector dealer or
local power company.
11. Do not place the Projector where the cord will be abused
by persons walking on it.
12. Follow all warnings and instructions marked on the
Projector.
13. To prevent damage to the projector due to lightning and
power-line surges, unplug the projector from the power
outlet, when not in use.
14. Do not overload wall outlets and extension cords with too
many products, because this can result in fire or electric
shock.
15. Never push objects of any kind into the Projector through
the cabinet slots as they may touch high-voltage points
or cause a short circuit. This could result in a fire or electric
shock.
16. Do not attempt to service the Projector yourself. Opening
or removing covers may expose you to dangerous voltage
or other hazards. Refer all servicing to qualified service
personnel.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFEGUARDS
Caution Concerning the Lamp Unit
There is a potential hazard of glass particles if the lamp ruptures. In case of
lamp rupture, contact your nearest Sharp Authorised Projector Dealer or
Service Centre for a replacement.
See “Replacing the Lamp” on page 47.
CAUTION
PRECAUCIÓN
PRÉCAUTION
BQC-XVZ9000/1
This label is pasted the side of the projector.
USER SERVICE SCREWS
VIS POUR ENTRETIEN PAR L’UTILISATEUR
PRECAUTIONS A OBSERVER LORS DU
LAMP REPLACEMENT
CAUTION
REMPLACEMENT DE LA LAMPE.
BEFORE REMOVING THE SCREW, DISCONNECT
POWER CORD. HOT SURFACE INSIDE.
ALLOW 1 HOUR TO COOL BEFORE REPLACING
THE LAMP. REPLACE WITH SAME SHARP LAMP
UNIT TYPE BQC-XVZ9000/1ONLY.
DEBRANCHER LE CORDON D’ALIMENTATION AVANT DE RETIRER LES VIS.
L’INTERIEUR DU BOITIERETANT EXTREMEMENT CHAUD, ATTENDRE1HEURE
AVANT DE PROCEDER AU REMPLACEMENTDE LA LAMPE.
NE REMPLACER QUE PAR UNE LAMPE SHARP DE TYPEBQC-XVZ9000/1.
RAYONSULTRAVIOLETS : PEUVENT ENDOMMAGER LES YEUX.
ETEINDRE LA LAMPE AVANT DE PROCEDERA L’ENTRETIEN.
LAMPE A MOYENNE PRESSION: RISQUED’EXPLOSION. DANGERPOTENTIEL
DE PARTICULES DE VERRE EN CAS D’ECLATEMENT DE LA LAMPE.
A MANIPULER AVEC PRECAUTION, SE REPORTER AU MODE D’EMPLOI.
UV RADIATION : CAN CAUSE EYE DAMAGE.
TURN OFF LAMP BEFORE SERVICING.
MEDIUM PRESSURE LAMP : RISK OF EXPLOSION.
POTENTIAL HAZARD OF GLASS PARTICLES IF
LAMP HAS RUPTURED. HANDLE WITH CARE.
SEE OPERATION MANUAL.
Cautions Concerning the Setup of the Projector
For minimal servicing and to maintain high image quality, SHARP recommends
that this projector be installed in an area free from humidity, dust and cigarette
smoke. When the projector is subjected to these environments, the lens and
part of filter must be cleaned more often than usual. As long as the projector
is properly maintained in this manner, use in these environments will not reduce
the overall operation life. Please note that all internal cleaning must be
performed by a Sharp Authorised Projector Dealer or Service Centre.
• Do not expose the projector to extreme heat or cold.
ם 35˚C ם 5˚C Operating temperature: +5°C to 35°C
Storage temperature: –20°C to +60°C
Notes on Operation
• The exhaust ventilative hole, the lamp cage cover and adjacent areas may
get extremely hot during projector operation. To prevent injury, do not touch
these areas until they have sufficiently cooled down.
• Allow at least 30 cm of space between the exhaust ventilative hole and the
nearest wall or obstruction.
• If the cooling fan becomes obstructed, a protection device will automatically
turn off the projector lamp. This does not indicate a malfunction. Remove
the projector power cord from the wall outlet and wait at least 10 minutes.
Then turn on the power by plugging the power cord back in. This will return
the projector to the normal operating condition.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFEGUARDS
Temperature Monitor Function
If the projector starts to overheat due to setup problems or a dirty air filter,
“TEMP.” and “ ” will flash in the lower-left corner of the picture. If the
temperature continues to rise, the lamp will turn off, the TEMPERATURE
WARNING indicator on the projector will flash, and after a 90-second cooling-
off period the power will shut off. Refer to “Lamp/Maintenance Indicators” on
page 45, for details.
• The cooling fan regulates the internal temperature, and its performance is
automatically controlled. The sound of the fan may change during projector
operation due to changes in the fan speed.
Lamp Monitor Function
When the projector is turned on after the lamp has been used for 1,900 hours,
“LAMP” and “ ” will flash in the lower-left corner of the picture to advise you
to replace the lamp. See page 47 for lamp replacement. If the lamp has been
used for 2,000 hours, the projector power will automatically turn off and the
projector will enter standby mode. Refer to “Lamp/Maintenance Indicators”
on page 45, for details.
Using the Terminal Cover
• When ceiling-mounting the projector, attach the terminal cover (supplied)
to hide the connecting cables.
• Use the terminal cover to hide the connecting cables when the projector is
used on a desktop or high mounted.
1 Install the terminal cover using the two attached clips.
2
2 Attach the terminal cover by aligning with the tab on the projector.
1
1
PUSH
2
1
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Outstanding Features
1. Wide DMD™*1 (Digital Micromirror Device) Chip
The DMD Chip allows for a higher contrast image. Also, as it has an aspect ratio of 16:9, it is possible to
view, in the best possible picture frame, software recorded on 16:9 from DVD or DTV.
*1 Digital Light Processing, DLP, Digital Micromirror Device and DMD are trademarks of Texas Instruments.
2. Full 720P Resolution
The high resolution panel of 921,600 pixels (1280 × 720 dots) allows for viewing high image quality just as
the original as well as HDTV 720P signals.
3. Low Fan Noise
A new optical engine has been developed for this product resulting in minimized fan noise for undisturbed
viewing.
4. For Use with DTV*2
Allows projection of DTV images and 16:9 wide-screen images when connected to a DTV decoder or
similar video systems.
*2 DTV is the umbrella term used to describe the new digital television system in the United States.
5. New Progressive Mode and Film Mode
Optimizes the image by converting the interlaced signal to the progressive. Useful for displaying slow-
moving images or still images. Three modes are available.
6. Advanced Video Circuitry
Provides high quality images with minimal dot crawl and cross colour noise.
7. Easy-to-use Graphical User Interface (GUI)
A multi-colour, icon-based menu system allows for simple image adjustments.
8. Colour Temperature Adjustment
The function can be used to adjust the colour temperature to suit the type of image input to the projector.
9. Gamma Correction Function
The gamma value setting can be adjusted according to the input source for optimal image contrast.
10. Brightness Switchover Function
Function with toggle switch to control the quantity of projected light. Select “NORMAL” or “BRIGHT” to
decrease or increase brightness, power consumption and fan noise.
11. Component Video Input
Utilizes a component video input signal (Y, CB, CR). The video signal is input as separate components to
provide superior colour and image quality.
12. Direct Computer Compatibility
A multi-scan RGB input accepts signals from VGA (640 dots × 480 lines) to SXGA (1,280 dots × 1,024
lines) and Macintosh (from 13" to 21") without the need for any additional hardware.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Access the PDF Operation Manuals of SharpVision Manager
PDF operation manuals of supplied GAMMA control software “SharpVision Manager” in several languages are
included in the CD-ROM. To utilize these manuals, you need to install Adobe Acrobat Reader on your PC (Windows
or Macintosh). If you have not installed Acrobat Reader yet, you can download it from the Internet (http://
To Install Acrobat Reader from the CD-ROM
For Windows:
For Macintosh:
1 Insert the CD-ROM in the CD-ROM drive.
2 Double click on the “My Computer” icon.
3 Double click on the “CD-ROM” drive.
4 Double click on the “acrobat” folder.
5 Double click on the “windows” folder.
6 Double click on the desired installation programme
and follow the instructions on the screen.
1 Insert the CD-ROM in the CD-ROM drive.
2 Double click on the “CD-ROM” icon.
3 Double click on the “acrobat” folder.
4 Double click on the “mac” folder.
5 Double click on the desired installation programme
and follow the instructions on the screen.
For other operating systems:
Please download Acrobat Reader from the Internet (http://www.adobe.com).
For other languages:
If you prefer using Acrobat Reader for languages other than those included in the CD-ROM, please download the
appropriate version from the Internet.
Accessing the PDF Manuals
For Windows:
For Macintosh:
1 Insert the CD-ROM in the CD-ROM drive.
2 Double click on the “My Computer” icon.
3 Double click on the “CD-ROM” drive.
4 Double click on the “MANUALS” folder.
5 Double click on the “SVM_E” folder.
6 Double click on the language (name of the folder)
that you want to view.
1 Insert the CD-ROM in the CD-ROM drive.
2 Double click on the “CD-ROM” icon.
3 Double click on the “MANUALS” folder.
4 Double click on the “SVM_E” folder.
5 Double click on the language (name of the folder)
that you want to view.
6 Double click on the “SVM_EE” pdf file to access
the SharpVision Manager manual.
7 Double click on the “SVM_EE” pdf file to access
the SharpVision Manager manual.
• If the desired PDF file cannot be opened by double clicking the mouse, start Acrobat Reader first, then specify the desired
file using the “File”, “Open” menu.
• See the “readme.txt” file on the CD-ROM for important information on the CD-ROM not included in this operation manual.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Menu Bars ................................................. 27
Adjusting the Picture ................................. 29
Adjusting the Computer Images
(RGB menu only) ................................. 32
Reducing Image Noise
(VIDEO menu only) .............................. 36
Turning On/Off the On-screen Display ...... 37
Setting the Video Signal
(VIDEO menu only) .............................. 37
Theatre Mode Functions............................ 38
Selecting a Background Image................. 39
Subtitle Setting .......................................... 40
Selecting the Economy Mode ................... 41
Selecting the Transmission Speed
Important Information
IMPORTANT SAFEGUARDS ................... 3
Outstanding Features ............................. 6
How to Access the PDF Operation
Manuals............................................... 7
Contents................................................... 8
Part Names .............................................. 9
Supplied Accessories............................. 12
Setup &
Connections
(RS-232C) ............................................ 42
Reversing/Inverting Projected Images ...... 43
Selecting the On-screen Display
Language ............................................ 43
Displaying the Adjustment Settings .......... 44
Connections ............................................ 13
Power Supply ............................................ 13
Connecting to Video Equipment ............... 13
Connecting to a Computer ........................ 15
Operating the Remote Control .................. 16
Using as a Wired Remote Control ............. 16
Power ON/OFF .......................................... 17
Zooming and Focusing ............................. 17
Setting Up the Screen............................. 18
Using the Adjustment Feet ........................ 18
Using the Lens Shift .................................. 18
Keystone Correction .................................. 19
Adjusting the Projection Distance ............. 20
Image Projection ..................................... 22
Rear Projection .......................................... 22
Projection Using a Mirror ........................... 22
Ceiling-mount Projection ........................... 22
Maintenance &
Troubleshooting
Lamp/Maintenance Indicators................ 45
Lamp Maintenance.................................. 46
Confirming the Lamp Usage Time ............ 46
Replacing the Lamp .................................. 47
Cleaning the Air Filters ........................... 49
Using the Kensington Lock ....................... 49
Troubleshooting ...................................... 50
Appendix
Operation Buttons
Connecting Pin Assignments ................ 51
(RS-232C) Specifications and
Command Settings ............................ 52
Wired Remote Control Terminal
Specifications..................................... 55
Computer Compatibility Chart ............... 56
Dimensions.............................................. 57
Specifications.......................................... 58
Glossary................................................... 59
Index ......................................................... 60
Using the Operation Buttons ................. 23
Selecting the Input Signal Source ............. 23
Adjusting the Picture Aspect Ratio............ 23
Gamma Correction Function ..................... 25
Basic Operation
Using the GUI (Graphical User
Interface) Menu Screen...................... 26
Basic Operations ....................................... 26
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names
Numbers next to the part names refer to the main pages in this manual where the topic is explained.
Projector
Front and Top View
Lens shift dial
Zoom knob
18
17
45 TEMPERATURE WARNING indicator
45
LAMP REPLACEMENT indicator
Focus ring
Adjuster
17
18
45 POWER indicator
4
Intake ventilative hole
Adjuster
18
16
Remote control sensor
Lens cap
12
26 MENU button
23
RESIZE button
23
INPUT button
26
ADJUSTMENT buttons
(∂/ƒ/ß/©)
17
POWER buttons
(ON/OFF)
26
ENTER button
UNDO button 26
Side and Rear View
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names
Numbers next to the part names refer to the main pages in this manual where the topic is explained.
Projector
Side and Rear View
Intake ventilative hole
Exhaust ventilative hole
4
4
4
Intake ventilative hole
Remote control sensor
16
S-VIDEO INPUT 3 terminal 13
(4-pin Mini DIN)
15
RS-232C port
(9-pin D-sub)
15
INPUT 5 COMPUTER-RGB port
(15-pin Mini D-sub)
INPUT 1 COMPONENT/ 14
RGB terminals (RCA)
DC 12V OUTPUT
Wired remote 16
INPUT 2 COMPONENT/
RGB terminals (RCA)
14
AC socket
13
control jack
VIDEO INPUT 4 terminal (RCA) 13
DC 12 V 200 mA
OUTPUT terminal
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names
Remote Control
Front View
Top View
Remote control signal transmitter
POWER buttons (ON/OFF) 17
MENU button
26
26
ENTER button
26
ADJUSTMENT buttons
(∂/ƒ/ß/©)
16 Wired remote control jack
UNDO button
INPUT 1 button
26
23
23
23
38
23
INPUT 3 button
INPUT 2 button
23 INPUT 5 button
INPUT 4 button
23
30
RESIZE button
THEATRE MODE button
CLR TEMP buttons
GAMMA button 25
AUTO SYNC button
19 KEYSTONE button
35
16 BACKLIGHT button
Inserting the batteries
Pull down the tab on the
battery cover and
remove the cover
towards the direction of
the arrow.
Insert two AA size
Insert the lower tab of
1
2
3
batteries, making sure
the polarities match the
and marks inside the battery compartment.
the battery cover into
the opening, and press
the cover until it clicks
in place.
Battery
cover
Battery cover
Battery
compartment
• If the remote control gets wet, wipe it dry immediately.
• Avoid excessive heat and humidity.
• If you will not be using the remote control for a long time, remove the batteries.
• Do not mix new and old or different types of batteries.
• There are operations that can only be carried out by remote control. Handle the remote control carefully.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Supplied Accessories
Remote control
Two AA size batteries
Power cord
(For Europe except
U.K.)
(For U.K., Hong Kong
and Singapore)
• The configuration of wall outlets differs from country to country.
Use the power cord that corresponds to the wall outlet in your
country.
For Europe only
Computer RGB
cable
21 pin RCA
conversion adaptor
• The RGB cable and 21 pin conversion adaptor are only
supplied with European models.
Video cable
Terminal cover
CD-ROM
(SharpVision Manager)
Lens cap
Two projector operation manuals
SharpVision Manager operation manual
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Power Supply
Connecting the Power Cord
Plug the supplied power cord into the AC socket on the back of the projector.
Power cord
CAUTION
• Make sure the power cord is firmly connected into the AC socket.
• The configuration of wall outlets differs from country to country. Use the power cord that corresponds to the wall outlet in your country.
• The projector will enter the stand-by mode after turning the power off and then re-plugging the power cord into the AC socket. However,
if you turned off the power by disconnecting the power cord or because of a power failure, the projector will automatically turn on without
pressing the POWER ON button.
Connecting to Video Equipment
You can connect your projector to a VCR, laser disc player, DVD player, DTV* decoder and other video equipment.
* DTV is the umbrella term used to describe the new digital television system in the United States.
CAUTION
• Make sure to turn both the projector and the video equipment off, before connecting.
• As this projector is not equipped with audio input terminals, commercially available audio equipment or your own equipment (such as
speakers or amplifiers) should be used.
Connecting a video source (VCR, laser disc player, DVD player or DTV decoder) using the INPUT 3
S-VIDEO and INPUT 4 VIDEO terminals
1 Connect one end of the S-video cable (commercially
available) to the INPUT 3 S-VIDEO terminal, or one end
of the video cable to the INPUT 4 VIDEO terminal on
the projector.
2 Connect the other end of the S-video cable or the video
cable to the S-video output or Video output terminal of
the video source.
The S-video input terminal uses a video signal system where
the picture is separated into a colour and luminance signal
to realise a higher-quality image.
• For higher quality video, you may use the S-video input terminal on the
projector. S-video cable is commercially available.
• If your video equipment does not have an S-video output terminal, use
the composite video output terminal.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to Video Equipment
Projector
1
S-video cable (commercially available)
1
2 To S-video output terminal
Video cable
2 To video output terminal
VCR,
Laser disc player,
DVD player or
DTV decoder
Connecting a video source (DVD player or DTV decoder) using the RCA INPUT 1 or 2 terminals
1 Connect each RCA connector of a component cable to the corresponding
RCA INPUT 1 or 2 terminals on the projector.
2 Connect the other end of the cable to the corresponding terminals on a DVD
player or DTV decoder.
When connecting this projector to a DVD player or DTV decoder, select
“Component” for “Signal Type” on the GUI menu. (See page 31.)
CAUTION
• Make sure to turn both the projector and the video equipment off, before
connecting.
Projector
2 To component output
terminals
Component cable
(commercially available)
DVD player
or
DTV decoder
*
1
*
* The (HD/C sync) and (VD) terminals may be used depending on the specifications of the DTV decoder connected to this
projector. Please refer to the operation manual of the DTV decoder for details.
Connecting to a DTV decoder with analog RGB output
1 Connect each RCA connector to the corresponding RCA INPUT 1 or 2 terminals on the projector.
2 Connect the other end of cable to the corresponding terminals on a DTV decoder.
When connecting this projector to analog RGB output of the DTV decoder, select “RGB” for “Signal Type” on the GUI
menu. (See page 31).
Projector
CAUTION
• Make sure to turn both the projector and the video equipment off,
before connecting.
2 To analog RGB
DTV decoder
output terminals
1 D-sub/5BNC cable
(Commercially available)
Five RCA-BNC adaptors (Commercially available)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to a Computer
You can connect your projector to a computer for projection of full colour computer images.
Connecting to a computer using the INPUT 5 COMPUTER-RGB port
1 Connect one end of the COMPUTER-RGB cable to the INPUT 5 COMPUTER-RGB port on the projector.
2 Connect the other end of the corresponding port on a computer.
CAUTION
• Before connecting, be sure to turn both the projector and the computer off. After making all connections, turn the projector
on first. The computer should always be turned on last.
When connecting this projector to a computer, select “RGB” for “Signal Type” on the GUI menu. (See page
31)
Connecting other compatible computers
When connecting the projector to a compatible computer other than an IBM-PC (VGA/SVGA/XGA/SXGA) or
Macintosh (i.e. Workstation), a separate cable may be needed. Please contact your dealer for more information.
When connecting this projector to a computer, select “RGB” for “Signal Type” on the GUI menu. (See page
31)
• Connecting computers other than the recommended types may result in damage to the projector, the computer, or both.
2
1
Computer-RGB cable
RS-232C cable (null modem, cross
type, commercially available)
Connecting RS-232C port
When the RS-232C port on the projector is connected to a computer with an RS-232C cable (null modem, cross
type, commercially available), the computer can be used to control the projector and check the status of the
projector. See page 52, 53 and 54 for details.
Connect an RS-232C cable (null modem, cross type, commercially available) to the serial port on the computer.
CAUTION
• Do not connect or disconnect an RS-232C cable to or from the computer while it is on. This may damage your computer.
• Please read the computer’s operation manual carefully.
• Refer to “Computer Compatibility Chart” on page 56 for a list of computer signals compatible with the projector. Use with computer
signals other than those listed may cause some of the functions not to work.
• The RS-232C function may not operate if your computer port is not correctly set up. Please refer to the operation manual of the computer for
details.
• The arrows (→, ↔) in the configuration above indicate the direction of the signals.
• A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest Sharp Authorised Projector Dealer or
Service Centre.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating the Remote Control
The remote control can be used to control the projec-
tor within the range shown on the left.
Remote Control
7 m
30˚
• The signal from the remote control can be reflected off a
screen for easy operation. However, the effective distance
of the signal may differ due to the screen material.
30˚
45˚
45˚
30˚
Remote Control
Using the remote control in a dark
room
The backlights of the operation buttons can be turned
on for five seconds and off by pressing BACKLIGHT.
If you want to turn off the backlights while they are on,
press BACKLIGHT again.
BACKLIGHT button
Using as a Wired Remote Control
When the remote control cannot be used due to the
range or positioning of the projector (rear projection,
etc.), connect a 3.5 mm stereo minijack cable
(commercially available) from the wired remote control
jack on the top of the remote control to the Wired remote
control jack on the back of the projector.
3.5 mm stereo minijack cable
(commercially available)
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Power ON/OFF
Projector
Press POWER ON.
• The flashing blue LAMP REPLACEMENT indicator
shows that the lamp is warming up. Wait until the
indicator stops flashing before operating the projector.
• If the power is turned off and then immediately turned
on again, it may take a short while before the lamp
turns on.
Remote control
POWER
buttons
• After the projector is unpacked and turned on for the first
time, a slight odour may be emitted from the exhaust
ventilative hole. This odour will soon disappear with use.
When the power is on, the LAMP REPLACEMENT
indicator lights, indicating the status of the lamp.
Blue: Lamp is ready.
Maintenance indicator
TEMP.
LAMP
POWER
Flashing blue: Warming up.
Red: Change the lamp.
Press POWER OFF.
Press POWER OFF again while the message is
displayed.
• If you accidentally pressed POWER OFF and do not want
to turn off the power, wait until the message disappears.
• When POWER OFF is pressed twice, the POWER indicator
will light up red and the cooling fan will run for about 90
seconds. The projector will then enter standby mode.
• Wait until the cooling fan stops running before disconnecting
the power cord.
• The power can be turned on again by pressing POWER
ON. When the power is turned on, the POWER indicator
and the LAMP REPLACEMENT indicators light blue.
Zooming and Focusing
The picture can be zoomed in or out, and focused by the Zoom knob and the Focus ring.
1
2
Slide the Zoom knob. The image can be
adjusted to the desired size within the zoom
range.
Rotate the Focus ring until the image on the
screen becomes clear.
1
2
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up the Screen
Using the Adjustment Feet
You can adjust the height of the image by raising the projector with
the foot releases.
1
1 Press the foot releases and lift the projector to the desired angle.
2 Remove your hands from the foot releases. Once the adjustment
feet have locked in position, release the projector.
3 If the screen is at an angle, the adjusters can be used to adjust
the angle of the image.
Returning the projector to its original position
While holding the projector, press the foot releases and slowly lower
the projector to its original position.
3
CAUTION
• Do not hold the lens when lifting or lowering the projector.
• When lowering the projector, be careful not to get your fingers caught in the area between the adjustment feet and the
projector.
• The projector is adjustable up to approximately 5° from the standard position.
• When the height of the projector is adjusted, the image may become distorted (keystoned), depending on the relative
positions of the projector and the screen. See page 19 for details on the keystone correction.
Using the Lens Shift
The picture can be adjusted within the shift range of the lens by rotating the lens shift dial on the top of the
projector using your finger.
Projector
Projected Image
Lens shift dial
UP
DOWN UP
DOWN
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Keystone Correction
This function can be used to adjust the Keystone
settings.
3
2
4b
1
2
3
4
Press KEYSTONE on the remote control.
1,4a
Press ENTER to display the test pattern.
Press
/
/
/
to make adjustments.
a. Press KEYSTONE to return to the normal
screen.
b. To reset the Keystone setting, press UNDO.
• Straight lines and the edges of the displayed image may
appear jagged, when adjusting the Keystone setting.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Projection Distance
Position the projector perpendicular to the screen with all feet flat and leveled to achieve an optimal image.
Move the projector forward or backward if the edges of the image are distorted.
• The projector lens should be centred in the middle of the screen. If the lens centre is not perpendicular to the screen, the
image will be distorted, making viewing difficult.
• Position the screen so that it is not in direct sunlight or room light. Light falling directly onto the screen washes out colours,
making viewing difficult. Close the curtains and dim the lights when setting up the screen in a sunny or bright room.
• A polarising screen cannot be used with this projector.
x
Standard Setup (Front Projection)
Place the projector at the required distance from the
screen according to the desired screen size. (See the
tables below.) The figures in the tables are based
y
z
upon projecting an image so that it occupies the
entire screen.
When using a normal
Distance from the lens centre to
Screen size (4:3)
Projection Distance (y)
screen (4:3)
the lower edge of the image (z)
In case of setting the
Diag. (x)
Width
Height
Maximum (y1)
Minimum (y2)
9.3 m (30'6")
7.4 m (24'4")
5.6 m (18'3")
3.7 m (12'1")
3.1 m (10'2")
2.6 m (8'8")
2.2 m (7'2")
Upper (z1)
0 cm (0")
0 cm (0")
0 cm (0")
0 cm (0")
0 cm (0")
0 cm (0")
0 cm (0")
Lower (z2)
–286 cm (–12'6")
–229 cm (–10')
–171 cm (–7'6")
–114 cm (–5')
–96 cm (–4'2")
–82 cm (–3'7")
–69 cm (–3')
16:9 picture to the full
horizontal width of the
4:3 screen.
635 cm (250") 508 cm (200") 381 cm (150") 12.6 m (41'4")
508 cm (200") 406 cm (160") 305 cm (120") 10.1 m (33')
381 cm (150") 305 cm (120") 229 cm (90") 7.5 m (24'9")
254 cm (100") 203 cm (80") 152 cm (60") 5.0 m (16'5")
213 cm (84") 170 cm (67") 127 cm (50") 4.2 m (13'9")
183 cm (72") 147 cm (58") 109 cm (43") 3.6 m (11'10")
4
152 cm (60") 122 cm (48") 91 cm (36")
3.0 m (9'10")
3
The formula for screen size and projection distance
y1 (Max.) = (0.05058x – 0.0447) × 3.28
y2 (Min.) = (0.03734x – 0.0447) × 3.28
z1 (Upper) = 0
x : Screen size (diag.)
y : Projection distance
: Screen area
: Picture area
z : Distance from the lens centre to the lower
z2 (Lower) = –0.45x
edge of the screen
• There is an error of 3% in the formula above.
• Values with a minus (–) sign indicate the distance of the lens centre below the bottom of the
screen.
When using a wide
screen (16:9)
In case of displaying the
16:9 picture on the whole
of the 16:9 screen.
Distance from the lens centre to
Screen size (16:9)
Diag. (x) Width
762 cm (300") 663 cm (261") 373 cm (147") 16.5 m (54'1") 12.2 m (39'11")
635 cm (250") 554 cm (218") 312 cm (123") 13.7 m (45'1") 10.1 m (33'3")
508 cm (200") 442 cm (174") 249 cm (98")
381 cm (150") 333 cm (131") 188 cm (74") 8.2 m (26'12") 6.1 m (19'11")
338 cm (133") 295 cm (116") 165 cm (65") 7.3 m (23'11") 5.4 m (17'7")
269 cm (106") 234 cm (92") 132 cm (52") 5.8 m (18'11") 4.3 m (13'11")
254 cm (100") 221 cm (87") 125 cm (49") 5.5 m (17'11")
234 cm (92") 203 cm (80") 114 cm (45") 5.0 m (16'5")
Projection Distance (y)
Maximum (y1) Minimum (y2)
the lower edge of the image (z)
Height
Upper (z1)
0 cm (0")
0 cm (0")
0 cm (0")
0 cm (0")
0 cm (0")
0 cm (0")
0 cm (0")
0 cm (0")
0 cm (0")
0 cm (0")
0 cm (0")
0 cm (0")
Lower (z2)
–374 cm (–12'3")
–311 cm (–10'3")
–249 cm (–8'2")
–187 cm (–6'2")
–166 cm (–5'5")
–131 cm (–4'4")
–125 cm (–4'1")
–114 cm (–3'9")
–105 cm (–3'5")
–90 cm (–2'11")
–75 cm (–2'5")
–50 cm (–1'8")
11.0 m (36')
8.1 m (26'7")
16
9
4.0 m (13'2")
3.7 m (12'1")
3.4 m (11'1")
2.9 m (9'6")
2.4 m (7'10")
1.6 m (5'2")
: Picture area
213 cm (84") 185 cm (73") 104 cm (41")
183 cm (72") 160 cm (63") 89 cm (35") 3.9 m (12'10")
152 cm (60") 132 cm (52") 74 cm (29")
102 cm (40") 89 cm (35") 51 cm (20")
4.6 m (15')
3.3 m (10'8")
2.2 m (7'1")
The formula for screen size and projection distance
y1 (Max.) = (0.05510x – 0.04593) × 3.28
y2 (Min.) = (0.04068x – 0.04369) × 3.28
z1 (Upper) = 0
x : Screen size (diag.)
y : Projection distance
z : Distance from the lens centre to the lower
z2 (Lower) = –0.4904x
edge of the screen
• There is an error of 3% in the formula above.
• Values with a minus (–) sign indicate the distance of the lens centre below the bottom of the screen.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Projection Distance
Upper and Lower Lens Shift Position
• This projector is equipped with a lens shift function that lets you adjust the projection height.
• Adjust it to match the setup configuration.
• The screen can be moved maximum the length of one screen vertically using the lens shift.
• Optimal image quality is produced with the projector positioned perpendicular to the screen with all feet flat and level. Tilting or angling
the projector will reduce the effectiveness of the lens shift function.
Screen size: 254 cm (100 inches)
Aspect ratio: 16:9
Screen
Lens centre
Upper lens shift position
(High mount setup)
90°
Lens centre
90°
Lower lens shift position
(Desktop setup)
Lower edge of screen (White portion) =
Standard (0) point
Upper and Lower Lens Shift Position (Ceiling Mount)
When the projector is in the inverted position, use the upper edge of the screen as the base line, and exchange
the lower and upper lens shift values.
Screen size: 254 cm (100 inches)
Aspect ratio: 16:9
Screen
90°
90°
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Projection
Rear Projection
• Place a translucent screen between the projector and
the audience.
• Use the projector’s menu system to reverse the
projected image. (See page 43 for use of this
function.)
• Optimal image quality can be achieved when the projector
is positioned perpendicular to the screen with all feet flat
and leveled.
Projection Using a Mirror
• When the distance between the projector and screen
is not sufficient for normal rear projection, you can
use a mirror to reflect the image onto the screen.
• Place a mirror (normal flat type) in front of the lens.
• Project the normal image onto the mirror.
• The image reflected from the mirror is projected onto
the translucent screen.
CAUTION
• When using a mirror, be sure to carefully position both the
projector and the mirror so the light does not shine into the
eyes of the audience.
Ceiling-mount Projection
• It is recommended that you use the optional Sharp
ceiling-mount bracket for this installation.
• Before mounting the projector, contact your nearest
Sharp Authorised Projector Dealer or Service Centre
to obtain the recommended ceiling-mount bracket
(sold separately). (AN-TK202 ceiling-mount bracket,
AN-TK201 extension tube, AN-NV6T ceiling adaptors
for AN-TK202 or AN-TK201)
• When the projector is in the inverted position, use the
upper edge of the screen as the base line.
• Use the projector’s menu system to select the
appropriate projection mode. (See page 43 for use
of this function.)
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Operation Buttons
Selecting the Input Signal Source
Press INPUT on the projector, INPUT 1, INPUT 2,
INPUT 3, INPUT 4 or INPUT 5 on the remote control
to select the desired input mode.
• When no signal is received, “NO SIGNAL” will be displayed.
When a signal that the projector is not preset to receive is
received, “NOT REG.” will be displayed.
INPUT buttons
On-screen Display
INPUT 1 Mode
INPUT 2 Mode
INPUT 3 Mode
INPUT 5 Mode
INPUT 4 Mode
Adjusting the Picture Aspect Ratio
This function allows you to modify or customize the
picture display mode to enhance the input image.
Depending on the input signal, you can choose SIDE
BAR, SMART STRETCH, CINEMA ZOOM, STRETCH,
NORMAL, or DOT BY DOT image.
1 Press RESIZE. Each time RESIZE is pressed, the
picture mode changes as shown on the next page.
2
1
2 To return to the standard image, press UNDO
while “RESIZE” is displayed on the screen.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Picture Aspect Ratio
VIDEO/DVD/DTV
Output screen image
SMART STRETCH CINEMA ZOOM
Input Signal
SIDE BAR
STRETCH
For 4:3 aspect ratio
480i
480P
NTSC
PAL
SECAM
Letter box image
With squeeze
720P
1080i
For 16:9 aspect ratio
EXAMPLE
SMART
STRETCH
CINEMA
ZOOM
SIDE BAR
STRETCH
480i
480P
NTSC
PAL
SECAM
For 4:3
aspect ratio
960
ן 720 1280
ן 720 1280
ן 720 1280
ן 720 480P
720P
1080i
960
ן 720 1280
ן 720 1280
ן 720 1280
ן 720 1280
ן 720 1280
ן 720 For 16:9
aspect ratio
–
–
–
–
–
–
COMPUTER
Output screen image
Input Signal
NORMAL
DOT BY DOT
VGA
For 4:3 aspect ratio
(640
ן 480) SVGA
For 4:3 aspect ratio
(800
ן 600) XGA
For 4:3 aspect ratio
(1024
ן 768) SXGA
For 5:4 aspect ratio
(1280
ן 1024) EXAMPLE
NORMAL
960
ן 720 960
ן 720 960
ן 720 900
ן 720 DOT BY DOT
SVGA (800
ן 600) 800
ן 600 1024
ן 720 1280
ן 720 1280
ן 720 For 4:3
aspect ratio
XGA (1024
ן 768) SXGA (1280
ן 960) For without
4:3 aspect ratio
SXGA (1280
ן 1024) 24
Download from Www.Somanuals.com. All Manuals Search And Download.
Gamma Correction Function
• Gamma is an image quality enhancement function
that offers a richer image by brightening the darker
portions of the image without altering the brightness
of the brighter portions.
• Four gamma settings are available to allow for
differences in the images displayed and in the
brightness of the room.
• When you are displaying images with frequent, dark
scenes, such as a film or concert, or when you are
displaying images in a bright room, this feature makes
the dark scenes easier to see and gives the
impression of greater depth in the image.
3
1,2
Gamma Modes
Selected Mode Gamma mode
STANDARD
GAMMA 1
Standard picture without gamma correction.
Brightens darker portions of images for more
enhanced presentations.
On-screen Display
GAMMA 2
CUSTOM
Gives greater depth to darker portions of
STANDARD
images for a more exciting theatre experience.
Allows you to adjust gamma value using
SharpVision Manager (supplied).
1 Press GAMMA to display “GAMMA”.
2 Then, the present Gamma mode is displayed.
Each time GAMMA is pressed, the gamma level
toggles as shown on the left.
GAMMA 1
GAMMA 2
CUSTOM
3 To return to the standard image, press UNDO
while “GAMMA” is displayed on the screen.
• The CUSTOM setting of VIDEO mode optimizes the video
source to reproduce the image more beautifully. It darkens
bright portions of the image and gives greater depth to
darker portions of the image.
Select CUSTOM as your default setting if you prefer a
smooth textured image to a sharply contrasted one.
• STANDARD and GAMMA 2 settings of VIDEO mode (except
COMPONENT 480P/720P/1080i) incorporate a DYNAMIC
GAMMA function for optimizing GAMMA correction frame
by frame in real time, thus providing a more beautiful image.
• GAMMA 1 settings are the same for both RGB and VIDEO
modes.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the GUI (Graphical User Interface) Menu Screen
Basic Operations
This projector has two sets of menu screens that allow
you to adjust the image and various projector settings.
These menu screens can be operated from the projector
2,3,5
or the remote control with the following procedure.
1,7
4
6
(GUI) On-screen Display
INPUT 3, 4 (VIDEO) mode
INPUT 1, 2 (COMPONENT) or 5 (RGB) mode
1
1
2
2
Main menu
Sub menu
3
3
5
5
1 Press MENU to display the INPUT 1, 2, 3, 4 or 5
4
2
mode menu bar.
2 Press
/
to select an adjustment main menu
on the menu bar.
3 Press
/
to select a specific adjustment item.
5
4 To display a single adjustment item, press ENTER
after selecting the item. Only the menu bar and
the selected adjustment item will appear.
5 Press
/
to adjust the item.
6 Press UNDO to return to the previous screen.
7 To exit the GUI, press MENU.
• For details on items on the menu screen, see the tree charts
on pages 27 and 28.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Bars
Items on the INPUT 3 or 4 Mode Menu Bar
Main menu
Sub menu
Main menu
Sub menu
Picture
Contrast
מ 30 ם 30 PRJ Mode
Front
Ceiling
ם Front Rear
Brightness
מ 30 ם 30 Color
Tint
מ 30 ם 30 מ 30 ם 30 מ 30 ם 30 מ 30 ם 30 מ 30 ם 30 מ 3 ם 3 Ceiling
ם Rear English
Sharp
Red
Language
Deutsch
Blue
Español
CLR Temp
Reset
Nederlands
Français
Italiano
Progressive Mode
2D Progressive
3D Progressive
Film Mode
Svenska
Português
Options
3D DNR
[ON/OFF]
Theater Mode
[NORMAL/BRIGHT]
Lamp Timer
OSD Display
Status
Normal
Level A
Level B
Auto
Video System
PAL (50/60Hz)
SECAM
NTSC4.43
NTSC3.58
PAL–M
PAL–N
Background
Blue
None
Economy Mode
RS232C Port [ON/OFF]
Auto Power Off [ON/OFF]
9600bps
RS-232C
38400bps
115200bps
*
Subtitle
מ 30 ם 30 * These values may be changed using the RESIZE mode.
• Only the items highlighted in the tree charts above can be adjusted.
• To adjust the items under the sub menu, press
after selecting the sub menu.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Bars
Items on the INPUT 1, 2 or 5 Mode Menu Bar
Sub menu
Sub menu
Main menu
Main menu
Picture
Contrast
מ 30 ם 30 PRJ Mode
Front
Ceiling
ם Front Rear
Brightness
מ 30 ם 30 Color
מ 30 ם 30 מ 30 ם 30 מ 30 ם 30 מ 30 ם 30 מ 30 ם 30 מ 3 ם 3 Tint
Ceiling
ם Rear English
Sharp
Red
Language
Deutsch
*
Blue
RGB
Español
CLR Temp
Reset
Nederlands
Français
Italiano
Component
2D Progressive
3D Progressive
Film Mode
Resolution
Signal Type
Progressive Mode
Svenska
Português
Fine Sync
Clock
מ 150 ם 150 Vert Freq
75 Hz
72 Hz
1
800
ן 600 Phase
מ 60 ם 60 מ 150 ם 150 מ 60 ם 60 2
640
ן 480 •
H-Pos
•
7
V-Pos
Reset
Resolution
800
ן 600 640
ן 480 Vert Freq
75 Hz
72 Hz
Status
1
Save Setting
2
•
Select Setting
Special Modes
Signal Info
•
7
Resolution
640
ן 480 720
ן 480 1
Auto Sync
2
•
Auto Sync Disp [ON/OFF]
•
7
Resolution 640
ן 480 Hor Freq
Vert Freq
37.5 kHz
72 Hz
Off
Normal
High Speed
*
Options
DNR
[ON/OFF]
Theater Mode
[NORMAL/BRIGHT]
Lamp Timer
Normal
Level A
Level B
Blue
OSD Display
Background
[ON/OFF]
None
Economy Mode
RS232C Port [ON/OFF]
Auto Power Off [ON/OFF]
9600bps
RS-232C
38400bps
115200bps
,
* **
מ 30 ם 30 Subtitle
* Not displayed in the INPUT 5 mode. The “3D” function is not available in INPUT 1, 2 or 5. (Therefore, “DNR” is displayed
on the On-screen Display of INPUT 1, 2 or 5.)
**These values may be changed using the RESIZE mode.
• The resolution, vertical frequency and horizontal frequency figures displayed above are for example purposes only.
• “Color”, “Tint”, and “Sharp” appear only when Component is selected in INPUT 1 or 2 mode.
• Only the items highlighted in the tree charts above can be adjusted.
• To adjust the items under the sub menu, press
after selecting the sub menu.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Picture
You can adjust the projector’s picture to your prefer-
ences with the following picture settings.
Description of Adjustment Items
2,3
button
button
Selected item
1,4
Contrast
Brightness
Color
For less contrast
For less brightness
For less colour intensity
For more contrast
For more brightness
For more colour intensity
Tint
Skin tones become purplish Skin tones become greenish
Sharp
Red
For less sharpness
For weaker red
For more sharpness
For stronger red
Blue
Reset
For weaker blue
All image adjustment items are returned to the factory preset
settings.
For stronger blue
(GUI) On-screen Display
e. g. (VIDEO input in INPUT 3 or 4 mode)
• “Color”, “Tint” and “Sharp” do not appear for RGB input in
INPUT 5 mode.
1
1 Press MENU. Menu bar and “Picture” menu
screen appear. GUI operation guide is also
displayed.
2 Press
/
to select a specific adjustment item.
to move the mark of the selected
3 Press
/
adjustment item to the desired setting.
4 To exit the GUI, press MENU.
2
• To reset all adjustment items, select “Reset” on the “Picture”
menu screen and press ENTER.
• The adjustments can be stored separately in the INPUT 1
to 5 modes.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Picture
Adjusting the Colour Temperature
This function can be used to adjust the colour
temperature to suit the type of image input to the
projector (DVD, video, computer image, TV broadcast,
etc.).
This function can be operated using the CLR TEMP
buttons on the remote control, as well as the GUI menu
screen.
Adjusting the Colour Temperature with the
Remote Control
1,2
1 Press CLR TEMP (–/+) on the remote control.
Then, the present colour temperature level is
displayed.
On-screen Display
2 Press CLR TEMP (–/+) to change the colour
temperature level.
• The descriptions of each of the button operations are
shown on the table below.
• “
operation.
” disappears after four-seconds of no-
Adjusting the Colour Temperature using the
GUI Menu Screen
2,3
Description of Colour Temperature
מ 3 (Red)
ם 3 1,4
button
button (Blue)
Decreases colour temperature Increases colour temperature for
for warmer, reddish,
incandescent-like images.
(Low colour temperature)
cooler, bluish, florescent-like
images.
(High colour temperature)
1 Press MENU. Menu bar and “Picture” menu
screen appear. GUI operation guide is also
displayed.
(GUI) On-screen Display
2 Press
/
to select “CLR Temp”.
3 Press
/
to move the mark of the colour
temperature setting to the desired setting.
4 To exit the GUI, press MENU.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Picture
Selecting the Signal Type
This function allows you to select the input signal type
COMPONENT or RGB for INPUT 1 or 2.
2,3
1 Press MENU. Menu bar and “Picture” menu
screen appear. GUI operation guide is also
displayed.
1,5
4
2 Press
/
.
to select “Signal Type”, and then
press
3 Press
/
to select “RGB” or “Component”.
4 Press ENTER to save the setting.
5 To exit the GUI, press MENU.
(GUI) On-screen Display
Progressive Mode
This function allows you to select the progressive display
of a video signal. The progressive display projects a
smoother video image.
2,3
1 Press MENU. Menu bar and “Picture” menu
screen appear. GUI operation guide is also
displayed.
1,5
4
2 Press
/
to select “Progressive Mode”, and
.
then press
3 Press
/
to select “2D Progressive”, “3D
Progressive” or “Film Mode”.
4 Press ENTER to save the setting.
5 To exit the GUI, press MENU.
(GUI) On-screen Display
Selects the following progressive conversion mode.
2D Progressive
This function is useful to display fast-moving images such as
sports and action films. This mode optimizes the image in a
displayed frame.
3D Progressive
This function is useful to display relatively slow-moving images
such as drama and documentary more clearly. This mode
optimizes the image by estimating the movement of a number
of preceding and succeeding frames.
Film Mode
Reproduces the image of film software clearly. Displays the
optimized image of film transformed with three-two pull down
enhancement to progressive mode images.
• Film Mode cannot work with PAL 50 Hz.
• The film source is a digital video recording with the original
encoded as is at 24 frames/second. The projector can convert
this film source to progressive video at 60 frames/second to play
back a high-definition image.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Computer Images (RGB menu only)
When displaying computer patterns which are very
detailed (tiling, vertical stripes, etc.), interference may
occur between the DMD pixels, causing flickering,
vertical stripes, or contrast irregularities in portions of
the screen. Should this occur, adjust “Clock”, “Phase”,
“H-Pos” and “V-Pos” for the optimum computer image.
2,3,4
1,5
Description of Adjustment Items
Selected item
Description
Clock
Phase
H-Pos
V-Pos
Reset
Adjusts vertical noise.
Adjusts horizontal noise (similar to tracking on your VCR).
Centres the on-screen image by moving it to the left or right.
Centres the on-screen image by moving it up or down.
All computer image adjustment items are returned to the factory
preset settings.
(GUI) On-screen Display
2
• Computer image adjustments can be made easily by pressing
AUTO SYNC ( ) on the remote control. See page 35 for details.
(Select the desired computer input mode with INPUT 1
or 2.)
1 Press MENU.
2 Press
3 Press
4 Press
/
to select “Fine Sync”.
/
to select a specific adjustment item.
3
/
to move the mark of the selected
adjustment item to the desired setting.
5 To exit the GUI, press MENU.
• To reset all adjustment items, select “Reset” on the “Fine Sync”
menu screen and press ENTER.
• The adjustable area of each item may be changed using the input
signal.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Computer Images (RGB menu only)
Saving and SelectingAdjustment Settings
This projector allows you to store up to seven adjustment
settings for use with various computers. Once these
settings are stored, they can be easily selected each
time you connect a computer to the projector.
2,3,4
1,6
Saving the adjustment setting
5
1 Press MENU.
2 Press
/
to select “Fine Sync”.
3 Press
/
.
to select “Save Setting”, and then
press
4 Press
/
to select the desired memory location
(GUI) On-screen Display
of the setting.
2
5 Press ENTER to save the setting.
6 To exit the GUI, press MENU.
3
Selecting a saved setting
1 Press MENU.
2 Press
/
to select “Fine Sync”.
3 Press
/
.
to select “Select Setting”, and then
3
press
4 Press
/
to select the desired memory setting.
5 Press ENTER to select the setting.
6 To exit from the GUI, press MENU.
• If a memory position has not been set, the resolution and frequency
setting will not be displayed.
• When selecting the stored adjustment setting with “Select Setting”,
the computer system should match the stored setting.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Computer Images (RGB menu only)
Special Mode Adjustment
Ordinarily, the type of input signal is detected and the
correct resolution mode is automatically selected.
However, for some signals, the optimal resolution mode
in “Special Modes” on the “Fine Sync” menu screen
may need to be selected to match the computer display
mode.
2,3,4
1,6
5
1 Press MENU.
2 Press
/
to select “Fine Sync”.
3 Press
/
.
to select “Special Modes”, and then
press
4 Press
/
to select the optimal resolution.
(GUI) On-screen Display
5 Press ENTER to save the setting.
6 To exit the GUI, press MENU.
• Avoid displaying computer patterns which repeat every other line
(horizontal stripes). (Flickering may occur, making the image hard
to see.)
• When inputting DTV 1080i signal, select the corresponding type of
signal in step 4 above.
• When inputting 720P RGB signal, select the corresponding type of
signal in step 4.
Checking the Input Signal
This function allows you to check the current input signal
information.
2,3
1,4
1 Press MENU.
2 Press
/
to select “Fine Sync”.
3 Press
/
to select “Signal Info” to display the
current input signal.
4 To exit the GUI, press MENU.
(GUI) On-screen Display
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Computer Images (RGB menu only)
Auto Sync Adjustment
• Used to automatically adjust a computer image.
• Auto Sync adjustment can be made manually by
pressing the AUTO SYNC button on the remote
control, or automatically by setting “Auto Sync” to
“Normal” or “High Speed” in the projector’s GUI menu.
2,3,4
1,5
Off
• Synchronized adjustment is not automatically
performed.
• Press AUTO SYNC to perform manual adjustment.
Normal
• Synchronized adjustment is automatically performed
the same as the “High Speed” setting.
• Adjustment using the “Normal” setting takes longer
to perform than using the “High Speed” setting, but it
is more accurate.
AUTO SYNC
button
High Speed
• The sync adjustment is automatically made each time
the projector is turned on while connected to a
computer or the input selection is changed.
• The Auto Sync adjustment setting previously made is
cleared when the projector’s setting is changed.
(GUI) On-screen Display
1 Press MENU.
2 Press
/
to select “Fine Sync”.
3 Press
/
to select “Auto Sync”, and then press
.
4 Press
/
to select “Normal” or “High Speed”.
5 To exit the GUI, press MENU.
On-screen Display
When “Normal” is selected
• When the optimum image cannot be achieved with Auto
Sync adjustment, use manual adjustments. (See page 32.)
• When performing AUTO SYNC in off or High Speed mode,
if you press AUTO SYNC once, then press it again within
one minute, AUTO SYNC will be executed in Normal mode.
g
During Auto Sync adjustment, the On-screen Display
changes as shown on the left.
When “High Speed” is selected
• The Auto Sync adjustment may take some time to complete,
depending on the image of the computer connected to the
projector.
g
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Computer Images (RGB menu only)
Auto Sync Display Function
Normally, an image is not superimposed during Auto
Sync adjustment. You can, however, choose to
superimpose a background image during Auto Sync
adjustment.
2,3,4
1,5
1 Press MENU.
2 Press
3 Press
4 Press
/
to select “Fine Sync”.
/
to select “Auto Sync Disp”.
/
to select “ ” to superimpose a
background image or “ ” to remove the
background image during Auto Sync adjustment.
5 To exit the GUI, press MENU.
(GUI) On-screen Display
Reducing Image Noise (VIDEO menu only)
3D Digital Noise Reduction (3D DNR) provides high
quality images with minimal background.
2,3,4
1 Press MENU.
2 Press
3 Press
4 Press
/
/
/
to select “Options”.
to select “3D DNR”.
to select “ ” (ON).
1,5
5 To exit the GUI, press MENU.
• If the image is clear, select “ ” (OFF) to prevent any blurring.
• The “3D” function is not available in INPUT 1, 2 or 5.
(Therefore, “DNR” is displayed on the On-screen Display
of INPUT 1, 2 or 5.)
(GUI) On-screen Display
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning On/Off the On-screen Display
This function allows you to turn on or off the on-screen
messages that appear during input select.
Description of OSD Display
2,3,4
Selected item
Description
1,6
Normal
Level A
All On-screen Display are displayed.
INPUT and AUTO SYNC are not displayed.
5
All On-screen Display are not displayed (except MENU,
KEYSTONE and warning display (Power off, Temp., Lamp
etc.)).
Level B
1 Press MENU.
2 Press
/
to select “Options”.
(GUI) On-screen Display
3 Press
/
.
to select “OSD Display”, and then
press
4 Press
/
to select the desired On-screen
Display.
5 Press ENTER to save the setting.
6 To exit the GUI, press MENU.
Setting the Video Signal (VIDEO menu only)
The video input system mode is preset to “Auto”;
however, it can be changed to a specific system mode
if the selected system mode is not compatible with the
2,3,4
connected audiovisual equipment.
1,6
1 Press MENU.
5
2 Press
/
to select “Options”.
3 Press
/
.
to select “Video Systems”, and then
press
4 Press
/
to select the desired video system
mode.
5 Press ENTER to save the setting.
(GUI) On-screen Display
6 To exit the GUI, press MENU.
• When the system mode is set to “Auto”, you may not receive
a clear picture due to signal differences. Should this occur,
switch to the video system of the source signal.
• AUTO cannot be set for PAL-M and PAL-N input signals.
Select “PAL-M” or “PAL-N” in “Video System” menu for PAL-
M and PAL-N input signals.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Theatre Mode Functions
Function as a toggle switch for controlling the quantity
of projected light. Select “NORMAL” or “BRIGHT” to
decrease or increase brightness, power consumption
and fan noise. This function can be operated using the
THEATER MODE button on the remote control, as well
as the GUI menu screen.
Description of Theatre Modes
Selected item
Description
1
Quantity of light is 70%.
NORMAL (
BRIGHT (
)
Power consumption is 310 W.
Quantity of light is 100%.
Power consumption is 345 W.
)
On-screen Display
Operating the Theatre Mode Function with
the Remote Control
1 Press THEATER MODE on the remote control.
The present Theatre Mode is displayed.
“
” disappears after four-seconds of
no-operation.
• “Theatre Mode” is factory preset to “NORMAL” .
• When selecting “BRIGHT“ in “Theater Mode”, the fan noise
is increased.
• Even when selecting “NORMAL” in “Theater Mode“, fan
noise may increase if internal temperature rises enough to
activate the cooling function.
Operating the Theatre Mode Function Using
the GUI Menu Screen
2,3,4
1 Press MENU.
2 Press
3 Press
4 Press
/
/
/
to select “Options”.
1,5
to select “Theater Mode”.
to select “ ” or “ ”.
5 To exit the GUI, press MENU.
(GUI) On-screen Display
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting a Background Image
This function allows you to select the image displayed
when no signal is being sent to the projector.
Description of Background Images
2,3,4
Selected item
Blue
Description
Blue screen
Black screen
1,6
None
5
1 Press MENU.
2 Press
/
to select “Options”.
3 Press
/
.
to select “Background”, and then
press
(GUI) On-screen Display
4 Press
/
to select the background image you
want to display on the screen.
5 Press ENTER to save the setting.
6 To exit the GUI, press MENU.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Subtitle Setting
With this function, you can adjust the vertical size of
the display to allow for subtitles.
Description of Subtitle Setting
2,3,4
מ 30 ם 30 button
button
1,5
Compresses the image to adjust Enlarges the image to adjust the
the vertical size of the display.
vertical size of the display.
1 Press MENU.
2 Press
/
/
to select “Options”.
3 Press
to select “Subtitle”.
4 Press
/
to move the mark of the subtitle
(GUI) On-screen Display
setting.
5 To exit the GUI, press MENU.
• The RESIZE modes that are available for the Subtitle setting
are SMART STRETCH and CINEMA ZOOM only. Please refer
to the page 24 for details.
• The value of the Subtitle setting may be changed using the
INPUT and RESIZE mode.
• When changing the screen with the Subtitle setting, not only
the bottom of the screen rises up but also the upper side is
changed to a certain point.
Digital shift
When the normal image is projected (without the
menu screen or most On-screen Displays*
displayed),
/
can be used to shift the image
down or up. Press UNDO to return the image center.
'/"
* This function does not work when most On-screen
Displays are displayed. However, it can be used
when “INPUT 1”, “INPUT 2”, “INPUT 3”, “INPUT 4”
or “INPUT 5” appears on the screen.
UNDO
• This function only works with certain picture mode displays.
On the final hole.
Press '.
Press ".
Press UNDO.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the Economy Mode
These functions allow you to reduce the power
consumption when the projector is in stand-by mode.
RS-232C Off Function
2,3,4
This projector consumes power when using a computer
connected to the RS-232C port. When not using this
port, “RS-232C Port” can be set to “ ” for reducing
stand-by power consumption.
1,5
Description of RS-232C Off
Stand-by power for RS-232C connection turned off.
RS-232C on
1 Press MENU.
(GUI) On-screen Display
2 Press
3 Press
4 Press
/
/
/
to select “Options”.
to select “RS-232C Port”.
to select “ ” or “ ”.
5 To exit the GUI, press MENU.
• Set “RS-232C Port” to “ ” when using the SharpVision
Manager (supplied).
On-screen Display
Automatic Power Shut-off Function
When no input signal is detected for more than 15
minutes, the projector will automatically shut off. The
on-screen message on the left will appear five minutes
before the power is automatically turned off.
Description of Automatic Power Shut-off
Power automatically shuts off after 15 minutes without
an input signal.
Automatic Power Shut-off disabled.
(GUI) On-screen Display
1 Press MENU.
2 Press
3 Press
4 Press
/
/
/
to select “Options”.
to select “Auto Power Off”.
to select “ ” or “ ”.
5 To exit the GUI, press MENU.
• “RS-232C Port” is factory preset to “ ”, and “Auto Power
Off” is factory preset to “ ”.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the Transmission Speed (RS-232C)
This menu allows you to adjust the transmission speed
of the RS-232C connection by selecting the baud rate.
2,3,4
1 Press MENU.
1,6
2 Press
/
/
to select “Options”.
5
3 Press
to select “RS-232C”, and then press
.
4 Press
/
to select the desired baud rate.
5 Press ENTER to save the setting.
6 To exit the GUI, press MENU.
(GUI) On-screen Display
• Make sure that both the projector and computer are set for
the same baud rate. Refer to the computer’s operation
manual for instructions for setting the baud rate.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Reversing/Inverting Projected Images
This projector is equipped with a reverse/invert image
function which allows you to reverse or invert the pro-
jected image for various applications.
2,3
Description of Projected Images
Selected item
Description
1,5
4
Front
Normal image
Ceiling
ם Front Rear
Inverted image
Reversed image
Reversed and inverted image
Ceiling
ם Rear 1 Press MENU.
2 Press
/
to select “PRJ Mode”.
(GUI) On-screen Display
3 Press
/
to select the desired projection mode.
4 Press ENTER to save the setting.
5 To exit the GUI, press MENU.
• This function is used for the reversed image and ceiling-
mount setups. See page 22 for these setups.
Selecting the On-screen Display Language
English is the preset language for the On-screen
Display; however, this can be changed to German,
Spanish, Dutch, French, Italian, Swedish, Portuguese,
2,3
Chinese, Korean or Japanese.
1 Press MENU.
1,5
4
2 Press
/
/
to select “Language”.
3 Press
to select the desired language.
4 Press ENTER to save the setting. The On-screen
Display is now programmed to display in the
language selected.
(GUI) On-screen Display
5 To exit the GUI, press MENU.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Displaying the Adjustment Settings
This function can be used to display all the adjusted
settings on the screen simultaneously.
1 Press MENU.
2
2 Press
/
to select “Status”.
1,4
3
3 Press ENTER to display all the adjustment
settings.
4 To exit the GUI, press MENU.
(GUI) On-screen Display
INPUT 3, 4 (VIDEO) mode
INPUT 1, 2 (COMPONENT) or 5 (RGB) mode
2
2
3
3
* The “3D” function is not available in INPUT 1, 2 or 5.
(Therefore, “DNR” is displayed on the On-screen Display
of INPUT 1, 2 or 5.)
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Lamp/Maintenance Indicators
Maintenance Indicators
• The warning lights on the projector indicate problems
inside the projector.
TEMP.
LAMP
POWER
• There are two types of warning lights: a TEMPERATURE
WARNING indicator that warns you when the projector
is too hot, and a LAMP REPLACEMENT indicator that
warns you when to change the lamp.
• If a problem occurs, either the TEMPERATURE
WARNING indicator or the LAMP REPLACEMENT
indicator will light up red. After turning off the power,
follow the procedures given below.
TEMPERATURE LAMP
POWER
indicator
WARNING
indicator
REPLACEMENT
indicator
Maintenance Indicator
Condition
Problem
Possible Solution
• Blocked air intake.
• Relocate the projector to an area with
proper ventilation.
TEMPERATURE
WARNING indicator
The internal
temperature is
abnormally high.
• Clogged air filter.
• Clean the filters.
(See page 49.)
• Cooling fan breakdown.
• Internal circuit failure.
• Take the projector to your nearest Sharp
Authorised Projector Dealer or Service
Centre for repair.
• Burnt-out lamp.
• Lamp circuit failure.
• Carefully replace the lamp. (See page 48.)
• Take the projector to your nearest Sharp
Authorised Projector Dealer or Service
Centre for repair.
LAMP REPLACE-
MENT indicator
The lamp does not
light up.
• Lamp has been used for
over 1,900 hours.
The lamp requires
replacement.
• If the TEMPERATURE WARNING indicator lights up, follow the above possible solutions and then wait until the projector has
cooled down completely before turning the power back on. (At least 5 minutes.)
• If the power is turned off and then turned on again, for example during a brief rest, the LAMP REPLACEMENT indicator may
be triggered, preventing the power from going on. Should this occur, unplug the power cord from the wall outlet and plug it
back in again.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Lamp Maintenance
Confirming the Lamp Usage Time
The lamp in this projector operates for approximately 2,000 cumulative hours, depending on the usage environ-
ment. (As the usage environment can vary significantly, the projector lamp may not operate for 2,000 hours.) It is
recommended that the lamp be replaced after approximately 1,900 cumulative hours of use or when you notice a
significant deterioration of the picture and colour quality. The lamp usage time can be checked with the On-screen
Display.
CAUTION
• Intense light hazard. Do not attempt to look into the aperture and lens while the projector is operating.
This function allows you to check the accumulated lamp
usage time.
2
1 Press MENU.
2 Press
/
to select “Options”. The lamp usage
1,3
time will be displayed in the “Lamp Timer” of
“Options”.
3 To exit the GUI, press MENU.
• It is recommended that the lamp be replaced after
approximately 1,900 cumulative hours of use. See page 48
for lamp replacement.
(GUI) On-screen Display
Condition
Problem
Possible Solution
The LAMP REPLACEMENT
• Lamp has been used for over 1,900
hours.
• Purchase a replacement lamp unit
(lamp/cage module) of the current
type BQC-XVZ9000/1 from your
nearest Sharp Authorised Projector
Dealer or Service Centre.
• Replace the lamp. (See page 48.) If
you wish, you may have the lamp
replaced at your nearest Sharp
Authorised Projector Dealer or
Service Centre.
indicator lights up red, and “LAMP”
and “ ” will flash in yellow in the
lower-left corner of the picture.
A significant deterioration of the
picture and colour quality occurs.
The power will automatically turn
off and the projector will enter
stand-by mode.
• Lamp has been used for over 2,000
hours.
“LAMP” and “ ” will flash in red in
the lower-left corner of the picture,
and the power will turn off.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the Lamp
CAUTION
• There is potential glass particles hazard if the lamp ruptures. In case of lamp rupture, contact your
nearest Sharp Authorised Projector Dealer or Service Centre for replacement.
• Do not remove the lamp cage directly after operation of the projector. The lamp may be extremely
hot. Wait at least one hour after the power cord is disconnected to allow the surface of the lamp cage
to fully cool down before removing the lamp cage.
It is recommended that the lamp be replaced after approximately 1,900 cumulative hours of use or when you
notice a significant deterioration of the picture and colour quality. Carefully change the lamp by following the steps
on the next page.
If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorised Projector
Dealer or Service Centre for repair. Purchase a replacement lamp unit (lamp/cage module) of the current type
BQC-XVZ9000/1 from your nearest Sharp Authorised Projector Dealer or Service Centre. Then carefully change
the lamp by following the instructions on the next page. If you wish, you may have the lamp replaced at your
nearest Sharp Authorised Projector Dealer or Service Centre.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the Lamp
Removing and installing the lamp unit
CAUTION
• Be sure to remove the lamp cage by the handle. Do not touch the glass surface of the lamp cage or the inside of the
projector.
• To avoid injury to yourself and damage to the lamp, carefully follow the steps below.
• Replace the lamp after turning off the power and unplugging the power cord.
Turn off the power.
Unplug the power cord.
Remove the lamp cage
cover.
1
2
3
Press POWER OFF. Wait until
the cooling fan stops running.
Loosen the user service screw
that secures the lamp cage cover
on the side of the projector. Then
lower the cover in the direction of
the arrow (to the open mark).
User service screws
Remove the lamp
cage.
Insert the new lamp
cage.
Attach the lamp cage
cover.
4
5
6
Remove the three-securing
Press the lamp cage firmly into
the lamp cage compartment.
Fasten the three-securing screws.
Close the lamp cage cover in the
direction of the arrow (to the
close mark) on the side of the
projector. Then tighten the user
service screw.
screws from the lamp cage. Hold
the lamp cage by the handle and
pull it horizontally towards you.
2
1
User service screws
Press POWER ON on
Plug in the power cord.
7
8
projector to reset lamp
timer.
While holding down ENTER, "
and |, press POWER ON.
• You need to reset lamp timer every time when replacing the lamp and confirm it to be reset on “Lamp Timer” menu.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning the Air Filters
• This projector is equipped with air filters to ensure the optimal operating condition of the projector.
• Periodically clean the air filter by vacuuming it off with a vacuum cleaner.
• The air filter should be cleaned every 100 hours of use. Clean the filters more often when the projector is used
in a dirty or smoky location.
Side and Rear view
How to clean the air filters
Unplug the power
cord.
Clean the air filters.
1
2
Clean the dust off by putting the
cleaner hose on the intake
ventilative hole of the air filters.
Air filter
Cleaner
hose
Bottom view
Cleaner
hose
Air filter
Using the Kensington Lock
This projector has a Kensington Security Standard
connector for use with a Kensington MicroSaver
Security System. Refer to the information that came
with the system for instructions on how to use it to
secure the projector.
Side view
Kensington Security
Standard connector
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Check
No picture appears.
• Projector power cord is not plugged into the wall outlet.
• Selected input is wrong. (See page 23.)
• Cables incorrectly connected to back panel of the projector. (See pages 13–15.)
• Remote control batteries have run down. (See page 11.)
• “Contrast” and “Brightness” adjustments are set to minimum position. (See page 29.)
Colour is faded or poor.
Picture is blurred.
• “Color” and “Tint” adjustments are not correct. (See page 29.)
• Adjust the focus. (See page 17.)
• Projection distance is too long or too short to allow for proper focus. (See pages 20 and 21.)
No OSD appears.
• OSD Display is set to “Level A” or “Level B”, preventing to display some or all On-screen
Displays. (See page 37.)
An unusual sound is occasion-
ally heard from the cabinet.
• If the picture is normal, the sound is due to cabinet shrinkage caused by temperature
changes. This will not affect operation or performance.
Maintenance indicator lights
up.
• Refer to “Lamp/Maintenance Indicators” on page 45.
Picture noise appears.
• Adjust the “Phase” setting. (See page 32.)
• Noise may appear when used with certain computers. Set the NOISE FILTER to ON
using the RS-232C command. (See pages 52–54.)
Image is green on INPUT 1 or
2 COMPONENT.
• Change the input signal type. (See page 31.)
Image is pink (no green) on
INPUT 1, 2 RGB.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Pin Assignments
INPUT 5 RGB Signal Input Port: 15-pin Mini D-sub female connector
RGB Input
Analog
1. Video input (red)
2. Video input
(green/sync on green)
3. Video input (blue)
4. Not connected
5. Composite sync
6. Earth (red)
7. Earth (green/sync on green)
8. Earth (blue)
9. Not connected
10. GND
11
6
1
15
10
5
11. GND
12. Bi-directional data
13. Horizontal sync signal
14. Vertical sync signal
15. Data clock
RS-232C Port: 9-pin D-sub male connector of the DIN-D-sub RS-232C cable
Pin No.
Signal
Name
I/O
Reference
9
6
1
2
3
4
5
6
7
8
9
Not connected
RD
SD
Receive Data
Send Data
Reserved
Signal Ground
Reserved
Reserved
Reserved
Input
Output
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Not connected
SG
5
1
51
Download from Www.Somanuals.com. All Manuals Search And Download.
(RS-232C) Specifications and Command Settings
PC control
A computer can be used to control the projector by connecting an RS-232C cable (null modem, cross type,
commercially available) to the projector. (See page 15 for connection.)
Communication conditions
Set the serial port settings of the computer to match those of the table on the next page.
Signal format: Conforms to RS-232C standard.
Baud rate: 9,600 bps
Data length: 8 bits
Parity bit: NONE
Stop bit: 1 bit
Flow control: None
Basic format
Commands from the computer are sent in the following order: command, parameter, and return code. After the
projector processes the command from the computer, it sends a response code to the computer.
Command format
Return code (0DH)
C1 C2 C3 C4 P1 P2 P3 P4
Command 4-digits Parameter 4-digits
Response code format
Normal response
Return code (0DH)
Problem response (communication error or incorrect command)
Return code (0DH)
O
K
E
R
R
When more than one code is being sent, send each command only after the OK response code for the previous
command from the projector is verified.
• When using the computer control function of the projector, the projector operating status cannot be read to the computer.
Therefore, confirm the status by transmitting the display commands for each adjustment menu and checking the status with
the On-screen Display. If the projector receives a command other than a menu display command, it will execute the com-
mand without displaying the On-screen Display.
Commands
EXAMPLE
• When “Brightness” of INPUT 1 Picture Adjustment is set to
מ 10. Computer
Projector
→
←
R
A
B
R
_
מ 1
0
O
K
52
Download from Www.Somanuals.com. All Manuals Search And Download.
(RS-232C) Specifications and Command Settings
CONTROL CONTENTS
COMMAND PARAMETER
RETURN
OK OR ERR
CONTROL CONTENTS
INPUT 5 (COMPUTER-RGB) DISPLAY
INPUT 5 (COMPUTER-RGB) ADJUSTMENT RESET
INPUT 1 (COMPONENT 1) SIGNAL TYPE : RGB
INPUT 1 (COMPONENT 1) SIGNAL TYPE : COMPONENT
INPUT 2 (COMPONENT 2) SIGNAL TYPE : RGB
INPUT 2 (COMPONENT 2) SIGNAL TYPE : COMPONENT
INPUT 1 (COMPONENT 1) 2D PROGRESSIVE
INPUT 1 (COMPONENT 1) 3D PROGRESSIVE
INPUT 1 (COMPONENT 1) Film MODE
INPUT 2 (COMPONENT 2) 2D PROGRESSIVE
INPUT 2 (COMPONENT 2) 3D PROGRESSIVE
INPUT 2 (COMPONENT 2) Film MODE
INPUT 3 (S-VIDEO) CONTRAST (
מ 30 — ם 30) INPUT 3 (S-VIDEO) BRIGHTNESS (
מ 30 — ם 30) INPUT 3 (S-VIDEO) RED (
מ 30 — ם 30) INPUT 3 (S-VIDEO) BLUE (
מ 30 — ם 30) INPUT 3 (S-VIDEO) COLOUR (
מ 30 — ם 30) INPUT 3 (S-VIDEO) TINT (
מ 30 — ם 30) INPUT 3 (S-VIDEO) SHARP (
מ 30 — ם 30) INPUT 3 (S-VIDEO) CLR TEMP (
מ 3 — ם 3) INPUT 3 (S-VIDEO) DISPLAY
COMMAND PARAMETER
RETURN
OK OR ERR
POWER ON
POWER OFF
P O W R _
P O W R _
K E Y S *
_
_
*
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
*
*
*
*
*
*
*
_
_
_
*
*
*
*
*
*
*
_
_
_
*
*
*
*
_
_
_
*
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
*
*
*
*
*
*
*
*
_
_
*
*
*
*
*
*
*
*
_
_
*
*
*
*
*
1
0
*
1
2
2
1
3
1
3
4
1
2
3
4
1
2
3
4
1
2
3
4
1
2
1
3
1
2
3
4
1
2
3
4
*
*
*
*
*
*
*
*
0
1
*
*
*
*
*
*
*
*
0
1
*
*
*
*
*
R C R E
R C R E
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
*
*
*
*
*
*
*
_
_
_
*
*
*
*
*
*
*
_
_
_
_
_
_
_
_
_
*
*
*
*
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
*
*
*
*
*
*
*
*
_
_
*
*
*
*
*
*
*
*
_
_
_
_
_
_
_
_
*
*
*
*
_
_
_
_
_
_
_
_
_
_
_
0
1
1
2
1
2
0
1
2
0
1
2
*
*
*
*
*
*
*
*
0
1
*
*
*
*
*
*
*
*
0
1
0
1
2
0
1
2
*
*
*
*
0
1
*
*
1
2
1
2
0
1
0
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
kHz (***. *OR_)
Hz (***. *OR_)
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
KEYSTONE (
מ 127 — ם 127) INPUT 1 (COMPONENT 1)
INPUT 2 (COMPONENT 2)
INPUT 3 (S-VIDEO)
I
I
I
I
A S
A S
B S
B S
I
I
I
I
I
I
I
I
I
R G B _
R G B _
V E D _
V E D _
R G B _
INPUT 4 (VIDEO)
R A
R A
R A
R B
R B
R B
I
I
I
I
I
I
P _
P _
P _
P _
P _
P _
INPUT 5 (COMPUTER-RGB)
AUTO SYNC START
A D J S _
R A S R _
INPUT 1 (COMPONENT 1) RESIZE : SIDE BAR
INPUT 1 (COMPONENT 1) RESIZE : SMART STRETCH R A S R _
INPUT 1 (COMPONENT 1) RESIZE : CINEMA ZOOM
INPUT 1 (COMPONENT 1) RESIZE : STRETCH
INPUT 2 (COMPONENT 2) RESIZE : SIDE BAR
R A S R _
R A S R _
R B S R _
V B P
I
_
V B B R _
V B R D _
INPUT 2 (COMPONENT 2) RESIZE : SMART STRETCH R B S R _
INPUT 2 (COMPONENT 2) RESIZE : CINEMA ZOOM
INPUT 2 (COMPONENT 2) RESIZE : STRETCH
INPUT 3 (S-VIDEO) RESIZE : SIDE BAR
INPUT 3 (S-VIDEO) RESIZE : SMART STRETCH
INPUT 3 (S-VIDEO) RESIZE : CINEMA ZOOM
INPUT 3 (S-VIDEO) RESIZE : STRETCH
INPUT 4 (VIDEO) RESIZE : SIDE BAR
INPUT 4 (VIDEO) RESIZE : SMART STRETCH
INPUT 4 (VIDEO) RESIZE : CINEMA ZOOM
INPUT 4 (VIDEO) RESIZE : STRETCH
INPUT 5 (COMPUTER-RGB) RESIZE : NORMAL
INPUT 5 (COMPUTER-RGB) RESIZE : DOT BY DOT
RGB GAMMA : STANDARD
R B S R _
R B S R _
R B S V _
R B S V _
R B S V _
R B S V _
R A S V _
R A S V _
R A S V _
R A S V _
R C S R _
R C S R _
G A M R _
G A M R _
G A M R _
G A M R _
G A M V _
G A M V _
G A M V _
G A M V _
V B B E
V B C O _
V B T
V B S H _
_
I
_
V B C T
V B R E
V B R E
_
_
_
*
INPUT 3 (S-VIDEO) ADJUSTMENT RESET
INPUT 4 (VIDEO) CONTRAST (
מ 30 — ם 30) INPUT 4 (VIDEO) BRIGHTNESS (
מ 30 — ם 30) INPUT 4 (VIDEO) RED (
מ 30 — ם 30) INPUT 4 (VIDEO) BLUE (
מ 30 — ם 30) INPUT 4 (VIDEO) COLOUR (
מ 30 — ם 30) INPUT 4 (VIDEO) TINT (
מ 30 — ם 30) INPUT 4 (VIDEO) SHARP (
מ 30 — ם 30) INPUT 4 (VIDEO) CLR TEMP (
מ 3 — ם 3) INPUT 4 (VIDEO) DISPLAY
V A P
I
V A B R *
V A R D *
V A B E
V A C O *
V A T
V A S H _
*
I
*
RGB GAMMA : GAMMA1
RGB GAMMA : GAMMA2
V A C T
V A R E
V A R E
_
_
_
RGB GAMMA : CUSTOM
VIDEO GAMMA : STANDARD
INPUT 4 (VIDEO) ADJUSTMENT RESET
INPUT 3 (S-VIDEO) 2D PROGRESSIVE
INPUT 3 (S-VIDEO) 3D PROGRESSIVE
INPUT 3 (S-VIDEO) Film MODE
VIDEO GAMMA : GAMMA1
V B
V B
V B
V A
V A
V A
I
I
I
I
I
I
P _
P _
P _
P _
P _
P _
VIDEO GAMMA : GAMMA2
VIDEO GAMMA : CUSTOM
INPUT 1 (COMPONENT 1) CONTRAST (
מ 30 — ם 30) R A P I
_
INPUT 4 (VIDEO) 2D PROGRESSIVE
INPUT 4 (VIDEO) 3D PROGRESSIVE
INPUT 4 (VIDEO) Film MODE
INPUT 1 (COMPONENT 1) BRIGHTNESS (
מ 30 — ם 30) R A B R _ INPUT 1 (COMPONENT 1) RED (
מ 30 — ם 30) INPUT 1 (COMPONENT 1) BLUE (
מ 30 — ם 30) INPUT 1 (COMPONENT 1) COLOUR (
מ 30 — ם 30) INPUT 1 (COMPONENT 1) TINT (
מ 30 — ם 30) INPUT 1 (COMPONENT 1) SHARP (
מ 30 — ם 30) INPUT 1 (COMPONENT 1) CLR TEMP (
מ 3 — ם 3) INPUT 1 (COMPONENT 1) DISPLAY
R A R D _
R A B E
R A C O _
R A T
R A S H _
_
CLOCK (
מ 150 — ם 150) I
I
I
I
I
I
N C L
*
PHASE (
מ 60 — ם 60) N P H _
A H P *
A V P _
I
_
H-POSITION (
מ 150 — ם 150) V-POSITION (
מ 60 — ם 60) R A C T
R A R E
R A R E
_
_
_
_
RGB INPUT DISPLAY
A R E
A R E
_
_
RGB ADJUSTMENT RESET
INPUT 1 (COMPONENT 1) ADJUSTMENT RESET
SAVE SETTING (1 — 7)
M E M S _
M E M L _
INPUT 2 (COMPONENT 2) CONTRAST (
מ 30 — ם 30) R B P I
SELECT SETTING (1 — 7)
INPUT 2 (COMPONENT 2) BRIGHTNESS (
מ 30 — ם 30) R B B R _ RGB HORIZONTAL FREQUENCY CHECK
RGB VERTICAL FREQUENCY CHECK
NORMAL AUTO SYNC
T
T
F R Q _
F R Q _
INPUT 2 (COMPONENT 2) RED (
מ 30 — ם 30) INPUT 2 (COMPONENT 2) BLUE (
מ 30 — ם 30) INPUT 2 (COMPONENT 2) COLOUR (
מ 30 — ם 30) INPUT 2 (COMPONENT 2) TINT (
מ 30 — ם 30) INPUT 2 (COMPONENT 2) SHARP (
מ 30 — ם 30) INPUT 2 (COMPONENT 2) CLR TEMP (
מ 3 — ם 3) INPUT 2 (COMPONENT 2) DISPLAY
R B R D _
R B B E
R B C O _
R B T
R B S H _
_
A A D J
A A D J
A A D J
_
_
_
HIGH SPEED AUTO SYNC
I
_
AUTO SYNC OFF
AUTO SYNC DISPLAY ON
I M A S _
I M A S _
R B C T
R B R E
R B R E
_
_
_
_
AUTO SYNC DISPLAY OFF
INPUT 2 (COMPONENT 2) ADJUSTMENT RESET
INPUT 5 (COMPUTER-RGB) CONTRAST (
מ 30 — ם 30) R C P I
INPUT 5 (COMPUTER-RGB) BRIGHTNESS (
מ 30 — ם 30) R C B R _ INPUT 5 (COMPUTER-RGB) RED (
מ 30 — ם 30) R C R D _
INPUT 5 (COMPUTER-RGB) BLUE (
מ 30 — ם 30) R C B E
_
_
INPUT 5 (COMPUTER-RGB) CLR TEMP (
מ 3 — ם 3) R C C T 53
Download from Www.Somanuals.com. All Manuals Search And Download.
(RS-232C) Specifications and Command Settings
CONTROL CONTENTS
THEATRE MODE NORMAL
COMMAND PARAMETER
RETURN
OK OR ERR
CONTROL CONTENTS
LANGUAGE SELECTION : ENGLISH
LANGUAGE SELECTION : DEUTSCH
LANGUAGE SELECTION : ESPAÑOL
LANGUAGE SELECTION : NEDERLANDS
LANGUAGE SELECTION : FRANÇAIS
LANGUAGE SELECTION : ITALIANO
LANGUAGE SELECTION : SVENSKA
LANGUAGE SELECTION :
COMMAND PARAMETER
RETURN
OK OR ERR
T H M D _
T H M D _
3 D N R _
3 D N R _
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
1
0
0
1
1
2
0
1
2
3
4
5
6
7
1
2
0
1
1
0
1
0
1
M E L A _ _
M E L A _ _
M E L A _ _
M E L A _ _
M E L A _ _
M E L A _ _
M E L A _ _
M E L A _ _
M E L A _ _
M E L A _ _
M E L A _ _
_
_
_
_
_
_
_
_
_
1
1
1
2
3
4
5
6
7
8
9
0
1
THEATRE MODE BRIGHT
VIDEO 3D DNR OFF
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
0–9999 (INTEGER)
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
VIDEO 3D DNR ON
OSD DISPLAY ON
I M D
I M D
I M D
I
I
I
_
_
_
OSD DISPLAY OFF (LEVEL A)
OSD DISPLAY OFF (LEVEL B)
VIDEO SYSTEM SELECTION : AUTO
VIDEO SYSTEM SELECTION : PAL
VIDEO SYSTEM SELECTION : SECAM
VIDEO SYSTEM SELECTION : NTSC4.43
VIDEO SYSTEM SELECTION : NTSC3.58
VIDEO SYSTEM SELECTION : PAL_M
VIDEO SYSTEM SELECTION : PAL_N
BACKGROUND SELECTION : BLUE
BACKGROUND SELECTION : NONE
AUTO POWER OFF : NO USE
AUTO POWER OFF : USE
LAMP USAGE TIME
M E S Y _
M E S Y _
M E S Y _
M E S Y _
M E S Y _
M E S Y _
M E S Y _
I M B G _
I M B G _
A P O W _
A P O W _
LANGUAGE SELECTION : PORTUGUÊS
LANGUAGE SELECTION :
LANGUAGE SELECTION :
T
L
T
T
_
_
_
REVERSE OFF
I M R E
I M R E
REVERSE ON
INVERT OFF
I M I N _
I M I N _
INVERT ON
• If an underbar (_) appears in the parameter column, enter a space. If an asterisk (*) appears, enter a value in the range
indicated in brackets under CONTROL CONTENTS.
•
*1 FINE SYNC can only be set in the displayed RGB mode.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Wired Remote Control Terminal Specifications
Specifications of wired remote control input
• ø3.5 mm minijack
• External: GND
• Internal: +3.3V
Function and transmission codes
JUDGEMENT
CODE
JUDGEMENT
CODE
SYSTEM CODE
DATA CODE
SYSTEM CODE
DATA CODE
CONTROL
ITEM
CONTROL
ITEM
C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14
C15
0
C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14
C15
0
ON
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
1
1
1
1
1
1
0
0
0
0
1
1
0
0
1
1
1
1
1
0
1
1
0
0
0
0
0
1
1
0
1
0
1
1
1
1
0
1
1
1
0
1
1
1
0
0
0
0
0
0
0
0
0
0
1
0
1
0
0
1
1
1
1
0
0
1
1
1
1
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
RESIZE
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
0
1
0
0
1
0
1
1
0
0
0
1
1
1
1
1
1
0
1
0
1
0
0
1
0
0
1
0
1
1
0
1
1
1
1
1
1
0
0
0
1
0
1
1
1
1
1
1
1
1
1
0
0
1
1
1
1
0
1
1
1
1
1
1
0
1
1
0
0
0
0
0
0
0
0
0
1
1
1
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
OFF
0
GAMMA
0
MENU
0
CLR TEMP +
CLR TEMP –
AUTO SYNC
KEYSTONE
INPUT 1
0
∂
0
0
ƒ
0
0
ß
0
0
©
0
0
ENTER
0
INPUT 2
0
UNDO
0
INPUT 3
0
THEATRE MODE
0
INPUT 4
0
INPUT 5
0
Wired remote control function code
LSB
MSB
C13 C14 C15
C1
1
System Code
C5
0
C6
*
Data Code
0
1
1
*
*
*
*
*
*
*
1
0
• System codes C1 to C5 are fixed at “10110”.
• Codes C14 and C15 are reverse confirmation bits, with “10” indicating “Front” and “01” indicating “Rear”.
Sharp remote control signal format
Transmission format: 15-bit format
D
D
D
D
D
D
D
D
D
D
D
D
D
67.5 ms
67.5 ms
Wave form of output signal: Output using Pulse Position Modulation
t
T1
T0
26.4 µs
“1”
“0”
“0”
“0”
“0”
“1”
“0”
t
D
• t
ס 264 µs • Pulse carrier frequency
ס 37.91 kHz • Duty ratio
ס 1:1 • T0
ס 1.05 ms • T1
ס 2.10 ms Transmission control code
Example of Reverse D to
15 bit
D
D
C1
C2
C3
C4
C5
C6
C7
C8
C9
0
C10 C11 C12 C13 C14 C15
C1
C2
C3
C4
C5
C6
C7
C8
C9
C10 C11 C12 C13 C14 C15
1
0
1
1
0
1
0
0
0
0
0
0
1
0
Data
Data
Deter-
System Address
Function Key Data Bit
Mask
Expansion
C1
1
C2
0
C3
1
C4
1
C5
0
C6
0
C7
1
C8
1
C9
1
C10 C11 C12 C13 C14 C15
mination
1
1
1
1
0
1
D to D Common Data Bit
Reverse in D
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Compatibility Chart
Horizontal Frequency: 15–81 kHz
Vertical Frequency: 43–100 Hz
Pixel Clock: 12–120 MHz
Compatible with sync on green and composite sync signals
SXGA compatible in advanced intelligent compression or intelligent compression
AICS (Advanced Intelligent Compression and Expansion System) resizing technology
PC/
MAC/
WS
Horizontal
Vertical
PC/
MAC/
WS
Horizontal
Vertical
VESA
Standard
VESA
Standard
Frequency Frequency
Frequency Frequency
Resolution
Display
Resolution
Display
(kHz)
27.0
31.5
37.9
27.0
(Hz)
60
(kHz)
54.3
64.0
64.1
67.5
75.7
54.8
65.9
67.4
(Hz)
60
70
72
75
80
60
72
74
640
ן 350 70
85
ן ן 1,152
ן 864 60
ן 720
ן 350 Advanced
Intelligent
Compression
31.5
27.0
31.5
37.9
27.0
31.5
37.9
26.2
31.5
34.7
37.9
37.5
43.3
47.9
53.0
31.4
35.1
37.9
44.5
48.1
46.9
53.7
56.8
64.0
35.5
40.3
56.5
58.1
68.7
73.5
77.2
70
60
70
85
60
70
85
50
60
70
72
75
85
90
100
50
56
60
70
72
75
85
90
100
43
50
70
72
85
90
96
SXGA
PC
640
ן 400 1,152
ן 882 64.0
45.0
60
60
ן ן 720P
VGA
True
VGA
720
ן 400 1,280
ן 720 ן ן ן PC/
MAC 13"
Upscale
34.9
67
640
ן 480 Advanced
Intelligent
Compression
48.4
60.0
46.8
49.6
68.5
60.0
60
75
75
75
75
60
ן ן PC/
MAC 19"
XGA
1,024
ן 768 Upscale
640
ן 480 MAC 16" SVGA 832
ן 624 Upscale
ן ן PC
MAC 21" SXGA 1,152
ן 870 PC (WS)
SGI (WS)
1,280
ן 960 ן Advanced
Intelligent
Compression
1,280
ן 1,024 53.5
60.9
71.9
50
66
76
SXGA
SUN (WS)
1,152
ן 900 ן ן SVGA
800
ן 600 ן ן ן ן ן ן Advanced
Intelligent
Compression
XGA 1,024
ן 768 80.6
100
• This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD) mode. Should this
occur, turn off the LCD display on the notebook computer and output the display data in “CRT only” mode. Details on how
to change display modes can be found in your notebook computer’s operation manual.
• This projector can receive 640
ן 350 VESA format VGA signals, however, “640 ן 400” will appear on the screen. 56
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
Rear View
Side View
Top View
Side View
Front View
475
Bottom View
Units: mm
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Product type Projector
Model XV-Z9000E
Video system PAL/PAL 60/PAL-M/PAL-N/SECAM/NTSC 3.58/NTSC 4.43
DTV 480i/480P/720P/1080i
Display method Single Panel Digital Micromirror Device (DMD™) by Texas Instruments, RGB optical
shutter method
DMD panel Panel size: 0.8Љ
Drive method: Digital Light Processing (DLP™) by Texas Instruments
No. of dots: 921,600 dots (1,280 [H]
ן 720 [V]) Lens 1–1.35
ן zoom lens, F3.0, f=32.5–44.0 mm Projection lamp 250 W NSH lamp
Video input signal RCA Connector: VIDEO (INPUT 4), composite video, 1.0 Vp-p, sync negative, 75 Ω
terminated
S-video input signal 4-pin Mini DIN connector (INPUT 3)
Y (luminance signal): 1.0 Vp-p, sync negative, 75 Ω terminated
C (chrominance signal): Burst 0.286 Vp-p, 75 Ω terminated
Component input signal RCA Connector (INPUT 1, 2)
Y: 1.0 Vp-p, sync negative, 75 Ω terminated
CB: 0.7 Vp-p, 75 Ω terminated
CR: 0.7 Vp-p, 75 Ω terminated
Horizontal resolution 520 TV lines (NTSC 3.58 input), 750 TV lines (DTV 720P input)
RGB input signal 15-PIN MINI D-SUB CONNECTOR (INPUT 5):
RGB separate/composite sync/sync on green type analog input: 0–0.7 Vp-p, positive,
75 Ω terminated
HORIZONTAL SYNC. SIGNAL: TTL level (positive/negative) or composite sync (Apple only)
VERTICAL SYNC. SIGNAL: Same as above
Pixel clock 12–120 MHz
Vertical frequency 43–100 Hz
Horizontal frequency 15–81 kHz
Computer control signal 9-pin D-sub connector (RS-232C Port)
Rated voltage AC 100–240 V
Input current 3.6 A
Rated frequency 50/60 Hz
Power consumption 345 W (SELECTING “BRIGHT” in the “Theatre Mode”)
310 W (SELECTING “NORMAL” in the “Theatre Mode”)
Power dissipation 1,400 BTU/hour
Operating temperature
ם 5°C to ם 35°C Storage temperature
מ 20°C to ם 60°C Cabinet Plastic
I/R carrier frequency 38 kHz
Dimensions (approx.) 475
ן 178 ן 406 mm (W ן H ן D) (main body only) 475
ן 178 ן 496 mm (W ן H ן D) (including terminal cover) Weight (approx.) 9.5 kg (main body only)
Supplied accessories Remote control, Two AA size batteries, Power cord (1.8 m), 21-pin RCA conversion
adaptor, Video cable, Computer RGB cable, Terminal cover, Lens cap (attached), CD-
ROM, Two projector operation manuals, SharpVision Manager operation manual
Replacement parts Lamp unit (Lamp/cage module) (BQC-XVZ9000/1), Remote control (RRMCG1657CESA),
AA size batteries, Power cord (QACCV4002CEZZ, QACCB5024CENA), 21-pin RCA
conversion adaptor (QSOCZ0361CEZZ), Video cable (QCNWGA001WJZZ), Computer
RGB cable (QCNW-5050CEZZ), Terminal cover (GCOVA1985CEKA), Lens cap
(PCAPH1056CESA), CD-ROM (UDSKA0047CEN1), Two projector operation manuals
(TINS-7521CEZZ, TINS-7522CEZZ), SharpVision Manager operation manual (TINS-
7523CEZZ)
This SHARP projector uses a DMD chip. This very sophisticated chip
contains 921,600 pixels. As with any high technology electronic
equipment such as large screen TVs, video systems and video
cameras, there are certain acceptable tolerances that the equipment
must conform to.
This unit has some inactive pixels within acceptable tolerances which
may result in inactive dots on the picture screen. This will not affect
the picture quality or the life expectancy of the unit.
Specifications are subject to change without notice.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
Aspect ratio
Width and height ratio of an image. The normal aspect ratio of a computer and video image is 4 : 3. There are also wide images with an aspect ratio of 16 : 9
and 21 : 9.
Auto Sync
Optimises projected computer images by automatically adjusting certain characteristics.
Background
Initial setting image projected when no signal is being input.
Cinema zoom
Mode that projects the 16:9 image which uses the centre of the image signal on the full-screen.
Clock
Clock adjustment is used to adjust vertical noise when clock level is incorrect.
CLR Temp (Colour temperature)
Function that can be used to adjust the colour temperature to suit the type of image input to the projector. Decrease the colour temperature to create warmer,
reddish images for natural flesh tones, or increase to create cooler, bluish images for a brighter picture.
Composite sync
Signal combining horizontal and vertical sync pulses.
Digital keystone correction
Function to digitally correct a distorted image when the projector is set up at an angle, smoothes out jaggies on keystone images and compresses the image
not only horizontally but vertically keeping the 4 : 3 aspect ratio.
Digital shift
Shifts image up or down easily by
VIDEO and DTV inputs.
/
buttons when RESIZE mode of input image is SMART STRETCH, CINEMA ZOOM, or DOT BY DOT of COMPUTER,
Dot by dot
Mode that projects images in their native resolution.
GAMMA
Image quality enhancement function that offers a richer image by brightening the darker portions of the image without altering the brightness of the brighter
portions. You can select four different modes : STANDARD, GAMMA 1, GAMMA 2 and CUSTOM.
Intelligent compression and expansion
High quality resizing of lower and higher resolution images to fit the projector’s native resolution.
Lens shift
The lens can be easily raised and lowered to minimise or eliminate “Keystone” type effect.
Phase
Phase shift is a timing shift between isomorphic signals with the same resolution. When phase level is incorrect, the projected image typically displays horizontal
flicker.
Progressive Mode
The progressive display projects a smoother video image. You can select three different modes : 2D Progressive, 3D Progressive and Film Mode.
RESIZE
Allows you to modify or customise the picture display mode to enhance the input image. You can select six different modes: SIDE BAR, SMART STRETCH,
CINEMA ZOOM, STRETCH, NORMAL, and DOT BY DOT.
RS-232C
Function to control the projector from the computer by using the RS-232C ports on the projector and computer.
Side bar
Mode that projects the normal 4:3 image at the 4:3 area for the centre of the screen.
Smart Stretch
Mode that stretches the right and left sides of the 4:3 image horizontally while maintaining the aspect ratio around the centre of the image to display it on the WIDE
screen.
Status function
Displays the settings of each adjustment item.
Stretch
Mode that stretches the 4:3 image horizontally to display it on the WIDE screen.
Sync on green
Video signal mode of a computer which overlaps horizontal and vertical sync signal to green colour signal pin.
3D DNR (3D Digital Noise Reduction)
Provides high quality images with minimal background.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
A
R
AC socket.......................................................................... 13
ADJUSTMENT buttons...................................................... 26
Adjusting the Picture ......................................................... 29
Adjustment feet ................................................................. 18
Air filters ............................................................................ 49
Aspect ratio....................................................................... 23
Automatic power shutoff function ..................................... 41
Auto sync adjustment ....................................................... 35
AUTO SYNC button........................................................... 35
Auto Sync Display............................................................. 36
Rear projection................................................................. 22
Remote control ................................................................. 11
Remote control sensor ..................................................... 16
Remote control signal transmitter .................................... 11
RESIZE button.................................................................. 23
RS-232C Off Function ...................................................... 41
RS-232C port ................................................................... 51
RS-232C Transmission Speed ......................................... 42
S
Save Setting ..................................................................... 33
Select Setting ................................................................... 33
SIDE BAR ......................................................................... 23
Signal Info ........................................................................ 34
Signal Type ...................................................................... 31
SMART STRETCH ............................................................ 23
Special Mode ................................................................... 34
Status function ................................................................. 44
STRETCH ......................................................................... 23
Subtitle ............................................................................. 40
S-VIDEO INPUT terminal.................................................. 13
SXGA................................................................................ 24
Sync ................................................................................. 35
Sync on green .................................................................. 51
B
Background ...................................................................... 39
BACKLIGHT button........................................................... 16
C
Ceiling-mount.................................................................... 22
Ceiling+Rear ..................................................................... 43
CINEMA ZOOM................................................................. 23
Clock ................................................................................. 32
CLR TEMP (Colour Temperature) buttons......................... 30
COMPONENT/RGB terminals ........................................... 14
COMPUTER-RGB port ...................................................... 15
D
Digital shift ........................................................................ 40
DOT BY DOT..................................................................... 23
T
TEMPERATURE WARNING indicator ............................... 45
THEATER MODE button ................................................... 38
Transmission Speed (RS-232C) ....................................... 42
E
Economy Mode ................................................................. 41
ENTER button...................................................................... 9
Exhaust ventilative hole....................................................... 4
U
UNDO button ................................................................... 26
F
V
Fine Sync .......................................................................... 32
Focus ring ......................................................................... 17
VIDEO INPUT terminal ..................................................... 13
Video System ................................................................... 37
G
W
GAMMA button ................................................................. 25
GUI (Graphical User Interface)......................................... 26
Wired remote control input jack ........................................ 16
Z
I
Zoom knob ........................................................................ 17
INPUT buttons................................................................... 23
INPUT port ........................................................................ 10
No.
3D DNR (3D Digital Noise Reduction) .............................. 36
K
Kensington Lock ............................................................... 49
KEYSTONE button ............................................................ 19
L
LAMP REPLACEMENT indicator....................................... 45
Lamp Timer ....................................................................... 46
Lens shift........................................................................... 18
M
MENU button..................................................................... 26
O
On-screen display............................................................. 37
On-screen display Language ........................................... 43
P
Phase ................................................................................ 32
POWER buttons ................................................................ 17
Power cord ........................................................................ 13
POWER indicator .............................................................. 45
PRJ Mode.......................................................................... 43
Progressive Mode ............................................................. 31
60
Download from Www.Somanuals.com. All Manuals Search And Download.
SHARP CORPORATION
Printed in Japan
In Japan gedruckt
Imprimé au Japon
Triykt i Japan
Impreso en Japón
Stampato in Giappone
Gedrukt in Japan
TINS-7521CEZZ
Download from Www.Somanuals.com. All Manuals Search And Download.
|