-
XV Z200E
PROJECTOR
PROJEKTOR
PROJECTEUR
PROJEKTOR
PROYECTOR
PROIETTORE
PROJECTOR
OPERATION MANUAL
BEDIENUNGSANLEITUNG
MODE D’EMPLOI
BRUKSANVISNING
MANUAL DE MANEJO
MANUALE DI ISTRUZIONI
GEBRUIKSAANWIJZING
ENGLISH .............
DEUTSCH............
FRANÇAIS ...........
SVENSKA ............
ESPAÑOL ............
ITALIANO .............
NEDERLANDS ....
-1 –
-1 –
-1 –
-1 –
-1 –
-1 –
-1 –
-70
-70
-70
-70
-70
-70
-70
Download from Www.Somanuals.com. All Manuals Search And Download.
This equipment complies with the requirements of Directive 89/336/EEC and 73/23/EEC as amended
by 93/68/EEC.
Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit
Änderung 93/68/EWG.
Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées
par la directive 93/68/CEE.
Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/23/EEG, gewijzigd door 93/68/
EEG.
Dette udstyr overholder kravene i direktiv nr. 89/336/EEC og 73/23/EEC med tillæg nr. 93/68/EEC.
Quest’ apparecchio è conforme ai requisiti delle direttive 89/336/EEC e 73/23/EEC come emendata
dalla direttiva 93/68/EEC.
Η εγκατάσταση αυτή ανταπꢀκρίνεται στις απαιτήσεις των ꢀδηγιών της Ευρωπαϊκής Ενωσης 89/
336/ΕꢁΚ και 73/23/ΕꢁΚ, #πως ꢀι κανꢀνισµꢀί αυτꢀί συµπληρώθηκαν απ# την ꢀδηγία 93/68/ΕꢁΚ.
Este equipamento obedece às exigências das directivas 89/336/CEE e 73/23/CEE, na sua versão
corrigida pela directiva 93/68/CEE.
Este aparato satisface las exigencias de las Directivas 89/336/CEE y 73/23/CEE, modificadas por
medio de la 93/68/CEE.
Denna utrustning uppfyller kraven enligt riktlinjerna 89/336/EEC och 73/23/EEC så som kompletteras
av 93/68/EEC.
Dette produktet oppfyller betingelsene i direktivene 89/336/EEC og 73/23/EEC i endringen 93/68/EEC.
Tämä laite täyttää direktiivien 89/336/EEC ja 73/23/EEC vaatimukset, joita on muutettu direktiivillä 93/
68/EEC.
SPECIAL NOTE FOR USERS IN THE U.K.
The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 10A fuse.
ASA
Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked
or
and of
the same rating as above, which is also indicated on the pin face of the plug, must be used.
Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted.
In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut
off the mains plug and fit an appropriate type.
DANGER
The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and
disposed of in a safe manner.
Under no circumstances should the cut-off plug be inserted elsewhere into a 10A socket outlet, as a
serious electric shock may occur.
To fit an appropriate plug to the mains lead, follow the instructions below:
WARNING:
THIS APPARATUS MUST BE EARTHED.
IMPORTANT:
The wires in this mains lead are coloured in accordance with the following code:
Green-and-yellow
Blue
Brown
: Earth
: Neutral
: Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured
markings identifying the terminals in your plug proceed as follows:
• The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is
marked by the letter E or by the safety earth symbol
or coloured green or green-and-yellow.
• The wire which is coloured blue must be connected to the terminal which is marked with the letter N
or coloured black.
• The wire which is coloured brown must be connected to the terminal which is marked with the letter L
or coloured red.
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using the projector, please read this operation manual carefully.
Introduction
ENGLISH
IMPORTANT
For your assistance in reporting the loss or theft of your
Model No.: XV-Z200E
Serial No.:
Projector, please record the Serial Number located on
the bottom of the projector and retain this information.
Before recycling the packaging, please be sure that
you have checked the contents of the carton thoroughly
against the list of “Supplied accessories” on page 12.
WARNING: Intense light source. Do not look into the beam or view it directly. Be especially careful that children
do not look directly into the beam.
WARNING: To reduce the risk of fire or electric shock, do not expose this product to
rain or moisture.
CAUTION: To reduce the risk of electric shock, do not remove cabinet. No user-serviceable parts are inside.
Refer servicing to qualified service personnel.
WARNING:
The cooling fan in this projector continues to run for about 90 seconds after the projector enters the standby mode.
During normal operation, when putting the projector into the standby mode always use the STANDBY button on the
projector or on the remote control. Ensure the cooling fan has stopped before disconnecting the power cord.
DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING THE POWER CORD.
FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE.
WARNING:
This is a Class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Caution Concerning the Lamp Replacement
There is potential glass particles hazard if the lamp ruptures.
PRECAUTIONS A OBSERVER LORS
DU REMPLACEMENT DE LA LAMPE.
LAMP REPLACEMENT
CAUTION
BEFORE REMOVING THE SCREW, DISCONNECT POWER CORD.
HOT SURFACE INSIDE. ALLOW 1 HOUR TO COOL BEFORE
REPLACING THE LAMP. REPLACE WITH SAME SHARP LAMP
UNIT TYPE BQC-XVZ200++1ONLY. UV RADIATION : CAN CAUSE
EYE DAMAGE. TURN OFF LAMP BEFORE SERVICING.
HIGH PRESSURE LAMP : RISK OF EXPLOSION.
DEBRANCHER LE CORDON D’ALIMENTATION AVANT DE RETIRER LES VIS.
L’INTERIEUR DU BOITIERETANT EXTREMEMENT CHAUD, ATTENDRE
1HEURE AVANT DE PROCEDER AU REMPLACEMENTDE LA LAMPE.
NE REMPLACER QUE PAR UNE LAMPE SHARP DE TYPEBQC-XVZ200++1.
RAYONSULTRAVIOLETS : PEUVENT ENDOMMAGER LES YEUX.
ETEINDRE LA LAMPE AVANT DE PROCEDER A L’ENTRETIEN.
POTENTIAL HAZARD OF GLASS PARTICLES IF LAMP HAS
RUPTURED. HANDLE WITH CARE. SEE OPERATION MANUAL.
LAMPE A HAUTE PRESSION: RISQUED’EXPLOSION.
DANGERPOTENTIEL DE PARTICULES DE VERRE EN CAS D’ECLATEMENT DE LA LAMPE.
A MANIPULER AVEC PRECAUTION, SE REPORTER AU MODE D’EMPLOI.
WARNING:
Some IC chips in this product include confidential and/or trade secret property belonging to Texas Instruments.
Therefore you may not copy, modify, adapt, translate, distribute, reverse engineer, reverse assemble or discompile
the contents thereof.
-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Using the “Options” Menu ............................... 51
Checking the Lamp Life Status .............................. 51
Turning on/off the On-screen Display ......................51
Selecting the Signal Type ....................................... 52
Setting the Video Signal (VIDEO menu only)...........52
Selecting a Background Image .............................. 53
Setting the Eco Mode ..............................................53
Automatic Power Shut-off Function ........................ 54
Selecting the Menu Screen Position ........................54
Selecting the Menu Colour ..................................... 55
Reversing/Inverting Projected Images............ 56
Introduction
Contents............................................................... 3
IMPORTANT SAFEGUARDS ............................... 4
Quick Guide ......................................................... 7
Part Names .......................................................... 8
Operating the Remote Control ......................... 11
Accessories ....................................................... 12
Connections & Setup
Connecting the Projector to Other Devices.... 14
Connecting the Power Cord ................................... 14
Connecting to Video Equipment.......................... 15
Connecting to a DVD Player and DTV Decoder ... 17
Connecting to a Computer .................................. 21
Controlling the Projector by a Computer ............. 23
Setup .................................................................. 24
Using the Swivel Stand............................................24
Removing the Swivel Stand .....................................24
Attaching the Swivel Stand ..................................... 25
Focusing and Zooming ...........................................25
Using the Lens Shift ................................................25
Adjusting the Projection Distance .......................... 26
Image Projection......................................................28
Appendix
Maintenance Indicators .................................... 58
Regarding the Lamp ......................................... 59
Lamp ...................................................................... 59
Caution Concerning the Lamp ................................59
Replacing the Lamp ................................................59
Removing and Installing the Lamp Unit ................. 60
Resetting the Lamp Timer .......................................61
Cleaning the Ventilative Holes ......................... 62
Using the Kensington Lock.............................. 63
Troubleshooting ................................................ 63
Connecting Pin Assignments .......................... 64
(RS-232C) Specifications
Basic Operation
and Command Settings .............................. 65
Computer Compatibility Chart ......................... 66
Specifications.................................................... 67
Dimensions........................................................ 68
Glossary............................................................. 69
Index................................................................... 70
Image Projection ............................................... 30
Basic Procedure ......................................................30
Selecting the On-screen Display Language ...........31
Turning the Power off .............................................. 32
Keystone Correction ................................................33
Placement of the Projected Image
Using the Keystone Correction ............................34
Freezing a Moving Image ....................................... 35
Adjusting the Picture Aspect Ratio ..........................35
Adjustments and Settings
Using the Menu Screen .................................... 38
Menu Selections (Adjustment) ................................38
Menu Selections (Settings) ..................................... 40
Menu Bar Items ................................................. 42
Adjusting the Picture ........................................ 44
Adjusting Image Preferences ..................................44
Adjusting the Colour Temperature .......................... 45
Gamma Correction Function ...................................46
Emphasizing the Contrast .......................................46
Picture Setting Function...........................................47
Adjusting the Computer and
DVD/DTV Images ......................................... 48
When Auto Sync is OFF...........................................48
Special Modes Adjustment .....................................49
Auto Sync Adjustment .............................................50
Checking the Input Signal .......................................50
-3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFEGUARDS
ATTENTION: Please read all of these instructions before you operate your Projector for the first
time. Save these instructions for future reference.
For your own protection and prolonged operation of your Projector, be sure to read the following “IMPORTANT
SAFEGUARDS” carefully, before use.
This projector has been engineered and manufactured to ensure your personal safety. But IMPROPER USE
CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the safeguards
incorporated into this Projector, observe the following basic rules for its installation, use and servicing.
1. Unplug the Projector from the wall outlet before
cleaning.
12. Follow all warnings and instructions marked on
the Projector.
2. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning.
3. Do not use attachments not recommended by
the Projector manufacturer, as they may cause
hazards.
4. Do not use the Projector near water; for example,
near a bathtub, washbowl, kitchen sink, laundry
tub, in a wet basement, near a swimming pool,
etc. Never spill liquid into the projector.
5. Do not place the Projector on an unstable cart,
stand, or table. The Projector may fall, which may
cause serious injury to a child or an adult, and/or
serious damage to the unit.
13. To prevent damage to the projector due to
lightning and power-line surges, unplug the
projector from the power outlet, when not in use.
14. Do not overload wall outlets and extension cords
with too many products, because this can result
in fire or electric shock.
15. Never push objects of any kind into the Projector
through the cabinet slots as they may touch high-
voltage points or cause a short circuit. This could
result in a fire or electric shock.
16. Do not attempt to service the Projector yourself.
Opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
6. Wall or Ceiling Mounting—The product should be
mounted to a wall or ceiling only as
recommended by the manufacturer.
17. Unplug the Projector equipment from the wall
outlet and refer servicing to qualified service
personnel under the following conditions:
7. Projector equipment and
cart combinations should
be moved with care.
Quick stops, excessive
force, and uneven
surfaces may cause the
equipment and cart
combination to overturn.
8. Slots and openings in the cabinet back and
bottom are provided for ventilation. To ensure
reliable operation of the Projector and to protect
it from overheating, these openings must not be
blocked or covered. The openings should never
be covered with cloth or other material.
a. When the power cord or plug is damaged
or frayed.
b. If liquid has been spilled into the Projector.
c. If the Projector has been exposed to rain
or water.
d. If the Projector does not operate normally
when you follow the operating instructions.
Adjust only those controls that are covered
by the operating instructions, as improper
adjustment of other controls may cause
damage and will often require extensive
work by a qualified technician to restore the
Projector to normal operation.
9. This Projector should never be placed near or
over a radiator or heating vent. The Projector
should not be placed in a built-in installation such
as a bookcase unless proper ventilation is
provided.
10. The Projector should be operated only from the
type of power source indicated on the back of
the projector or in the specifications. If you are
not sure of the type of power supplied to your
home, consult your Projector dealer or local
power company.
e. If the Projector has been dropped or the
cabinet has been damaged.
f. When the Projector exhibits a distinct
change in performance—this indicates a
need for service.
18. When replacement parts are required, be sure
the service technician has used replacement
parts specified by the manufacturer that have the
same characteristics as the original parts.
Unauthorised substitutions may result in fire,
electric shock, or other hazards.
11. Do not place the Projector where the cord will be
abused by persons walking on it.
-4
Download from Www.Somanuals.com. All Manuals Search And Download.
19. This Projector is provided with one of the following
types of plugs. If the plug should fail to fit into the
power outlet, please contact your electrician.
Do not defeat the safety purpose of the plug.
a. Two-wire type mains plug.
b. Three-wire grounding type mains plug with
a grounding terminal.
This plug will only fit into a grounding type
power outlet.
• Digital Light Processing, DLP, Digital Micromirror Device and DMD are trademarks of Texas Instruments.
• Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or
other countries.
• PC/AT is a registered trademark of International Business Machines Corporation in the United States.
• Macintosh is a registered trademark of Apple Computer, Inc. in the United States and/or other countries.
• All other company or product names are trademarks or registered trademarks of their respective compa-
nies.
-5
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFEGUARDS
Be sure to read the following safeguards when setting up
your projector.
I If the cooling fan becomes obstructed, a protection
Caution concerning the lamp unit
device will automatically turn off the projector lamp. This
does not indicate a malfunction. Remove the projector
power cord from the wall outlet and wait at least 10
minutes. Then turn on the power by plugging the power
cord back in. This will return the projector to the normal
operating condition.
I There is a potential hazard of glass
particles if the lamp ruptures. In case
of lamp rupture, contact your near-
est Sharp Authorised Projector
Dealer or Service Centre for replace-
ment.
CAUTION
PRECAUCIÓN
PRÉCAUTION
BQC-XVZ200++1
See “Replacing the Lamp” on page 59.
Cautions regarding the transportation of the pro-
jector
Cautions concerning the setup of the projector
I For minimal servicing and to maintain high image qual-
ity, SHARP recommends that this projector be installed
in an area free from humidity, dust and cigarette smoke.
When the projector is subjected to these environments,
the lens and part of filter must be cleaned more often
than usual. As long as the projector is properly main-
tained in this manner, use in these environments will
not reduce the overall operation life. Please note that
all internal cleaning must be performed by a Sharp
Authorised Projector Dealer or Service Centre.
I When transporting the projector, be sure not to subject
it to hard impact and/or vibration, as this can result in
damage. Take extra caution with the lens. Before mov-
ing the projector, be sure to unplug the power cord from
the wall outlet, and disconnect any other cables con-
nected to it.
Other connected equipment
I When connecting other audio-visual equipment or a
computer to the projector, make the connections AF-
TER turning off the projector and the equipment to be
connected.
I Please read the operation manuals of the projector and
the equipment to be connected for instructions on how
to make the connections.
Do not set up the projector in places exposed to
direct sunlight or bright light.
I Position the screen so that it is not in direct sunlight or
room light. Light falling directly on the screen washes
out the colours, making viewing difficult. Close the cur-
tains and dim the lights when setting up the screen in a
sunny or bright room.
Temperature monitor function
I If the projector starts to overheat
due to setup problems or blockage
Do not subject the projector to hard impact and/
or vibration.
I Take care with the lens so as not to hit or damage the
of the air vents, “
“
corner of the picture. If the tem-
”
and
” will blink in the lower left
surface of the lens.
perature continues to rise, the lamp will turn off, the
temperature warning indicator on the projector will blink,
and after a 90-second cooling-off period the projector
will enter the standby mode. Refer to “Maintenance In-
dicators” on page 58 for details.
Rest your eyes occasionally.
I Watching the screen for long hours continuously will make
your eyes tired. Be sure to occasionally rest your eyes.
Do not expose the projector to extreme heat or
cold.
Info
I Operating temperature:
+5°C to 35°C
I Storage temperature:
•
The cooling fan regulates the internal temperature, and
its performance is automatically controlled. The sound
of the fan may change during projector operation due
to changes in the fan speed. This does not indicate
malfunction.
+
+
35˚C
5˚C
–20°C to +60°C
Notes on Operation
I The exhaust ventilative
holes, the lamp unit cover
and adjacent areas may
get extremely hot during
projector operation. To pre-
vent injury, do not touch
these areas until they have
sufficiently cooled down.
I Allow at least 30 cm of space between the exhaust
ventilative hole and the nearest wall or obstruction.
-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Guide
In this page, connection of the projector and the video equipment is explained as an example
for the procedure from setup to projection. Refer to each page for details.
Required equipments
Video equipment
Projector
Remote control
• Insert the batteries.
(Page 11)
Power cord
Video cable
1. Place the projector facing a wall or a screen.
2. Connect to video equipment. (Page 16)
6. Turn the projector on using
control. (Page 30)
on the remote
ON button
INPUT 4 button
The power indicator
illuminates green.
7. Press
on the remote control to select the
INPUT 4 mode. (Page 31)
"On-screen Display
To INPUT 4
8. Turn on the video equipment.
Video cable
terminal
ON
To video out
put terminal
3. Connect the output terminal of the video equip-
ment to the input terminal of the audio equip-
ment using an audio cable.
9. Play the video.
10.Adjust the image size, image position and the
focus. (Page 25)
4. Plug the power cord into the AC socket of the
projector and into the wall outlet. (Page 14)
Adjust the height of the image
by rotating the lens shift dial.
Adjust the zooming by
moving the zoom knob.
5. Remove the lens cap from the lens.
Lens cap
Adjust the focus by
rotating the focus ring.
Note
Power cord
• This projector can also be connected to a computer
as well as to video equipment. (Page 21)
-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names
Numbers in
refer to the main pages in this operation manual where the topic is explained.
Projector (Front and Top View)
Lens shift dial
25
58 TEMPERATURE
WARNING indicator
Zoom knob 25
58
LAMP indicator
Exhaust ventilative hole
6
30 POWER indicator
Focus ring
25
11
6
Exhaust ventilative hole
Remote control sensor
Lens cap
Attaching the Lens Cap
The lens cap can be attached to the
projector using commercially
available straps (for cellular phones
etc.), as shown in the figure.
Projector (Side and Rear View)
39
38 MENU button
ADJUSTMENT buttons
(ƒ/∂/ß/©)
32
STANDBY
button
UNDO button 39
31
INPUT button
33
KEYSTONE button
30
ON button
47
39
PICTURE SETTING button
ENTER button
35
RESIZE button
24
Swivel Stand
LOCK/UNLOCK lever
-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector (Rear View)
Remote control sensor
11
62
Intake ventilative hole
Intake ventilative hole
62
18
INPUT 3 S-VIDEO terminal 15
23
INPUT 2/DIGITAL INPUT
terminal
RS-232C terminal
(9-pin D-sub)
(4-pin Mini DIN)
AC socket
14
INPUT 1 COMPONENT
17
terminals (RCA)
INPUT 4 VIDEO terminal (RCA) 16
20 DIGITAL INPUT
TYPE switch
Using the Terminal Cover
When the projector is used on a desktop, high mounted or ceiling mounted, attach the terminal cover (supplied)
to hide the connecting cables.
Attaching the Terminal
Cover
1 Align with the tabs on
the projector and
then press the
Removing the Terminal
Cover
1 Loosen the two screws
on the bottom of the
projector.
terminal cover in the
direction of the arrow.
2 Tighten the two
screws on the bottom
of the projector.
2 Raise the terminal cover
and pull it out in the
direction of the arrow.
2
1
2 Tighten the screws
1 Loosen the screws
-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names
Remote Control (Front View)
STANDBY button 32
ON button
30
38
KEYSTONE button
ENTER button
33
39
MENU button
39
ADJUSTMENT buttons
(ƒ/∂/ß/©)
UNDO button
INPUT 1 button
39
31
31
31
50
31
INPUT 3 button
INPUT 2 button
31 DIGITAL INPUT button
INPUT 4 button
35
47
RESIZE button
AUTO SYNC button
PICTURE SETTING button
RGB/COMP. button 52
35 FREEZE button
Remote Control (Top View)
Remote control signal transmitters
-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating the Remote Control
Remote control
Available Range of the Remote Control
I The remote control can be used to control the projector
7 m
30˚
within the ranges shown in the illustration.
Note
30˚
45˚
• The signal from the remote control can be reflected off a screen
for easy operation. However, the effective distance of the signal
may differ due to the screen material.
45˚
When using the remote control:
• Be sure not to drop, or expose to moisture or high temperature.
• The remote control may malfunction under a fluorescent lamp.
Under that circumstance, move the projector away from the fluo-
rescent lamp.
30˚
Remote control
Inserting the Batteries
The batteries (two “AA” size) are included in
the package.
1 Pull down the tab on the cover
and remove the cover towards
the direction of the arrow.
2 Insert the included batteries.
• Insert the batteries making sure the
polarities correctly match the
and
marks inside the battery compart-
ment.
3 Insert the lower tab of the
cover into the opening, and
lower the cover until it clicks
in place.
Incorrect use of the batteries may cause them to leak or explode. Please follow the precautions below.
Caution
• Insert the batteries making sure the polarities correctly match the
and
marks inside the battery compart-
ment.
• Batteries of different types have different properties, therefore do not mix batteries of different types.
• Do not mix new and old batteries.
This may shorten the life of new batteries or may cause old batteries to leak.
• Remove the batteries from the remote control once they have run out, as leaving them can cause them to leak.
Battery fluid from leaked batteries is harmful to your skin, therefore be sure to first wipe them and then remove
them using a cloth.
• The batteries included with this projector may exhaust over a short period, depending on how they are kept.
Be sure to replace them as soon as possible with new batteries when they have run out.
• Remove the batteries from the remote control if you will not be using the remote control for a long time.
-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
Supplied accessories
Power cord
(For Europe except U.K.)
Remote control Two AA size batteries
(For U.K., Hong Kong
and Singapore)
(For Australia
and New Zealand)
Note
• Depending on the region, projectors are shipped with only
one power cord (see above). Use the power cord that cor-
responds to the wall outlet in your country.
21 pin RCA
Video cable
Terminal cover
conversion adaptor
(Supplied for Europe only)
Screws for terminal cover
Lens cap
Projector Operation manual
Optional accessories
3 RCA to 15-pin D-sub cable (3.0 m)
DVI to 15-pin D-sub adaptor (20 cm)
DVI cable (3.0 m)
AN-C3CP
AN-A1DV
AN-C3DV
Note
• Some of the cables may not be available depending on the region. Please check with your nearest Sharp
Authorised Projector Dealer or Service Centre for replacement.
-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections and Setup
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Projector to Other Devices
Before Connecting
Note
• Before connecting, be sure to unplug the power cord of the projector from the AC outlet and turn off
the devices to be connected. After making all connections, turn on the projector and then the other
devices.
When connecting a computer, be sure that it is the last device to be turned on after all the connec-
tions are made.
• Be sure to read the operation manuals of the devices to be connected before making connections.
This projector can be connected to:
Video equipment:
I A VCR, DVD player or other video equipment (See page 15.)
I A DVD player or DTV* decoder (See page 17.)
*DTV is the umbrella term used to describe the new digital television system in the United States.
A computer using:
I DVI to 15-Pin D-sub adapter (See page 21.)
I A DVI cable (See page 22.)
I An RS-232C cable (See page 23.)
Connecting the Power
Cord
Supplied
accessory
Plug in the supplied power cord into
the AC socket on the rear of the pro-
jector.
Power cord
-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to Video Equipment
S-video cable
(commercially available)
Connecting to Video
Equipment Using an
S-video Cable (INPUT 3)
Using an S-video cable, a VCR, DVD player or
other video equipment can be connected to
INPUT 3 input terminal.
To INPUT 3 terminal
1 Connect an S-video cable to
the projector.
2 Connect the S-video cable to
the video equipment.
Note
• The INPUT 3 (S-VIDEO) terminal uses a
video signal system in which the picture
is separated into color and luminance sig-
nals to realize a higher-quality image. To
view a higher-quality image, use a com-
mercially available S-video cable to con-
nect the INPUT 3 terminal on the projec-
tor and the S-video output terminal on the
video equipment.
To S-video output terminal
VCR or other video equipment
-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Projector to Other Devices
Connecting to Video
Equipment Using a
Composite Video Cable
(INPUT 4)
Using a composite video cable, a VCR, DVD
player or other video equipment can be con-
nected to INPUT 4 input terminal.
1 Connect a composite video
cable to the projector.
To INPUT 4 terminal
2 Connect the composite video
cable to the video equipment.
Composite video cable
To video output terminal
VCR or other video equipment
-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to a DVD Player and DTV Decoder
Connecting to
Component Video
Equipment Using a
Component Cable
(INPUT 1)
Use a component cable when connecting com-
ponent video equipment such as DVD players
and DTV decoders to INPUT 1 terminals.
To INPUT 1 terminals
1 Connect a component cable to
the projector.
2 Connect the above cable to the
component video equipment.
Note
Component cable
(commercially available)
• Make sure to turn both the projector and
the video equipment off before connect-
ing.
To analog component
output terminal
DVD player or
DTV decoder
-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Projector to Other Devices
3 RCA to 15-pin
D-sub cable
Type: AN-C3CP
(3.0 m)
Connecting to Compo-
Optional
accessories
nent Video Equipment
Using a 3 RCA to 15-pin
D-sub Cable and the
DVI to 15-pin D-sub
Adaptor (INPUT 2)
DVI to 15-pin
D-sub adaptor
Type: AN-A1DV
(20 cm)
Use a 3 RCA to 15-pin D-sub cable and the
DVI to 15-pin D-sub adaptor when connecting
component video equipment such as DVD
players and DTV decoders to INPUT 2 termi-
nal.
1 Connect a DVI to 15-pin D-sub
adaptor to the projector.
To INPUT 2 terminal
2 Connect a 3 RCA to 15-pin D-
sub cable to the above adaptor.
• Secure the connectors by tightening the
thumbscrews.
DVI to 15-pin
D-sub adaptor
(sold separately)
3 Connect the above cable to the
video equipment.
Note
• When connecting this projector to com-
ponent output terminal of the DTV de-
coder, select “Component” for “Signal
Type” on the OSD menu or press
on
the remote control. (See page 52.)
• Make sure to turn both the projector and
the video equipment off before connect-
ing.
3 RCA to 15-pin
D-sub cable
(sold separately)
To analog component
output terminal
DVD player or
DTV decoder
-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional
accessory
Connecting to RGB
Video Equipment Using
the DVI to 15-pin D-sub
Adaptor and the RGB
Cable (INPUT 2)
DVI to 15-pin D-sub adaptor
Type: AN-A1DV (20 cm)
Use the DVI to 15-pin D-sub adaptor and the
RGB cable when connecting RGB video equip-
ment such as DVD players and DTV decoders
to INPUT 2 terminal.
1 Connect a DVI to 15-pin D-sub
adaptor to the projector.
To INPUT 2 terminal
2 Connect the above adaptor to
an RGB cable.
3 Connect the above cable to the
video equipment.
DVI to 15-pin
D-sub adaptor
(sold separately)
• Secure the connectors by tightening the
thumbscrews.
Note
• When connecting this projector to DVI out-
put of the DTV decoder, select “RGB” for
“Signal Type” on the OSD menu or press
on the remote control. (See page 52.)
RGB cable
(commercially
available)
To RGB output terminal
DVD player or
DTV decoder
-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Projector to Other Devices
DVI cable
Type: AN-C3DV
(3.0 m)
Optional
accessory
Connecting to Video
Equipment with the DVI
Output Terminal Using
a DVI Cable (DIGITAL
INPUT)
Use the DVI cable when connecting video
equipment with the DVI output terminal such
as DVD players and DTV decoders to DIGITAL
INPUT terminal.
1 Slide the “DIGITAL INPUT
TYPE” switch on the back ter-
minal board to “VIDEO”.
To DIGITAL INPUT
terminal
DIGITAL INPUT
TYPE switch
2 Connect the DVI cable to the
DIGITAL INPUT terminal.
3 Connect the other end to the
corresponding terminal on the
DVD player or DTV decoder.
• Secure the connectors by tightening the
thumbscrews.
DVI cable
(sold separately)
Note
• Select DIGITAL INPUT mode when con-
necting to video equipment with the digi-
tal output terminal. (See page 31.)
• Make sure to turn both the projector and
the video equipment off before switching
the “DIGITAL INPUT TYPE” switch and
connecting.
To DVI digital output terminal
DVD player or
DTV decoder
-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to a Computer
Optional
accessory
Connecting to a Computer
Using the DVI to 15-pin
D-sub Adaptor and the
RGB Cable (INPUT 2)
DVI to 15-pin D-sub adaptor
Type: AN-A1DV (20 cm)
1 Connect a DVI to 15-pin D-sub
adaptor to the projector.
2 Connect the above adaptor to
an RGB cable.
To INPUT 2 terminal
3 Connect the above cable to the
computer.
• Secure the connectors by tightening the
thumbscrews.
DVI to 15-pin D-sub adaptor
(sold separately)
Note
•
Refer to “Computer Compatibility Chart” on
page 66 for a list of computer signals
compatible with the projector. Use with
computer signals other than those listed may
cause some of the functions not to work.
When connecting the projector to a computer
in this way, select “RGB” for “Signal Type” on
RGB cable
(commercially available)
•
•
•
the OSD menu or press
on the remote
control. (See page 52.)
To RGB output terminal
A Macintosh adaptor may be required for use
with some Macintosh computers. Contact your
nearest Sharp Authorised Projector Dealer or
Service Centre.
Depending on the computer you are using, an
image may not be projected unless the signal
output setting of the computer is switched to
the external output. Refer to the computer op-
eration manual for switching the computer sig-
nal output settings.
Notebook computer
Connecting the thumbscrew cables
I Connect the thumbscrew cable making sure that it fits cor-
rectly into the terminal. Then, firmly secure the connec-
tors by tightening the screws on both sides of the plug.
I
Do not remove the ferrite core attached to the RGB cable.
Ferrite core
-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Projector to Other Devices
DVI cable
Type: AN-C3DV
(3.0 m)
Optional
accessory
Connecting to a com-
puter with DIGITAL
RGB output Terminal
(DIGITAL INPUT)
1 Slide the “DIGITAL INPUT
TYPE” switch on the back ter-
minal board to “PC”.
2 Connect a DVI cable to the pro-
jector.
To DIGITAL INPUT
terminal
DIGITAL INPUT
TYPE switch
3 Connect the above cable to the
computer.
• Secure the connectors by tightening the
thumbscrews.
Note
• Select DIGITAL INPUT mode when con-
necting to digital output terminal of the
computer. (See page 31.)
DVI cable
• Before switching the “DIGITAL INPUT
TYPE” switch and connecting, be sure to
unplug the power cord of the projector
from the AC outlet and turn off the com-
puter to be connected. After making all
connections, turn on the projector and
then the computer.
(sold separately)
To DVI digital output terminal
• Be sure that the computer is the last de-
vice to be turned on after all the connec-
tions are made.
Desktop computer
“Plug and Play” function
I This projector is compatible with VESA-standard DDC 1/DDC 2B. The projector and a VESA DDC
compatible computer will communicate their setting requirements, allowing for quick and easy setup.
I Before using the “Plug and Play” function, be sure to turn on the projector first and the con-
nected computer last.
Note
• The DDC “Plug and Play” function of this projector operates only when used in conjunction with a VESA
DDC compatible computer.
-22
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling the Projector by a Computer
Controlling the
Projector Using an
RS-232C Cable
When the RS-232C terminal on the projector
is connected to a computer with an RS-232C
cable (null modem, cross type, commercially
available), the computer can be used to con-
trol the projector and check the status of the
projector. See page 65 for details.
To RS-232C terminal
1 Connect an RS-232C cable to
the projector.
2 Connect the above cable to the
computer.
RS-232C cable
(commercially available)
Note
• Do not connect or disconnect an RS-232C
cable to or from the computer while it is
on. This may damage your computer.
• The RS-232C function may not operate if
your computer terminal is not correctly set
up. Refer to the operation manual of the
computer for details.
• Refer to “Computer Compatibility Chart”
on page 66 for a list of computer signals
compatible with the projector. Use with
computer signals other than those listed
may cause some of the functions not to
work.
To RS-232C terminal
Desktop computer
-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
Using the Swivel Stand
1
2
You can adjust the angle and direction of the
projected image by using the Swivel Stand.
1 Unlock the lever on the Swivel
Stand.
Swivel Stand
LOCK/UNLOCK
lever
2 Adjust the angle and direction
of the projected image as you
want by lifting up the projec-
tor and rotating the projector
on the Swivel Stand.
Adjustable up to
10° from the
standard position.
Caution
• Do not hold the lens when lifting, lower-
ing or rotating the projector.
•
When lowering the projector, be careful not
to get your fingers caught in the area be-
tween the Swivel Stand and the projector.
Adjustable up to
25° from the
standard position.
Note
• When the height or direction of the pro-
jector is adjusted, the image may become
distorted (keystoned), depending on the
relative positions of the projector and the
screen. See page 33 for details on the
keystone correction.
Adjustable up to
3° from the
standard position.
3
3 Lock the lever on the Swivel
Stand.
2
Removing the Swivel
Stand
1 Lift the projector (2) with
pressing the removing-stand
button on the back of the pro-
jector (1).
1
Removing-
stand button
-24
Download from Www.Somanuals.com. All Manuals Search And Download.
Attaching the Swivel
Stand
1 Align the tabs on the front bot-
tom of the projector (1).
3
1
2 While holding down the button
(2), place the projector onto
the Swivel Stand (3) to attach.
2
3 Press the projector down
firmly to attach it to the Swivel
Stand to make sure it is se-
curely attached to the Swivel
Stand.
Zoom knob
Focusing and Zooming
The picture can be focused and zoomed in or
out by using the Focus ring and the Zoom
knob.
Focus ring
Lens shift dial
1 Rotate the Focus ring until the
image on the screen comes
into focus.
2 Slide the Zoom knob. The im-
age can be adjusted to the de-
sired size within the zoom
range.
Projected Image
UP
Using the Lens Shift
The picture can be adjusted within the shift
range of the lens by rotating the lens shift dial
on the top of the projector using your finger.
DOWN
-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
Adjusting the Projection Distance
• Refer to pages 33 and 34 about the function of Keystone correction and placement of projector using the
correction.
• Decide the placement of the projector referring to the figures on the table and the diagram below
according to the size of your screen and input signal.
Centre of the screen
(a) Maximum projection distance
(b)Minimum projection distance
Placement range
(c) Horizontal placement range when projection distance is maximum.
(d)Horizontal placement range when projection distance is minimum.
(e) Vertical placement range when projection distance is maximum.
(f) Vertical placement range when projection distance is minimum.
(e)
(d)
(c)
(f)
10°
Note
(b)
(a)
• The aspect ratio of the projected image shifts slightly when
the lens shift is at a position other than the top position.
• The aspect ratio of the projected image also shifts slightly
when the “H Keystone” and “V Keystone” functions are
adjusted simultaneously.
• When adjusting “H Keystone” and “V Keystone” at the same
time, the values of adjustable angles for each setting
become smaller.
• Keystone correction cannot be applied to On-screen
Display.
• When Keystone correction is applied, the resolution of image
can be deteriorated to some extent.
• There are errors of 3% in the formulas below.
When using a wide
screen (16:9)
In case of displaying
the 16:9 picture on the
whole of the 16:9
screen.
Projection distance and Keystone correction
Screen size
(16:9)(x)
Maximum projection distance
Horizontal Placement range (c)
Minimum projection distance
Horizontal Placement range (d)
Vertical
placement range
(e)
Vertical
placement range
(f)
Projection
distance (a)
Projection
distance (b)
Diag.
Composite, S-video
480 /P, 1080
Composite, S-video
480 /P, 1080
720P
RGB
720P
RGB
I
I
I
I
3.6m (11'10'')
2.7m (8' 10'')
2.4m (7' 10'')
1.9m (6' 3'')
1.8m (5' 11'')
1.6m (5' 3'' )
1.5m (4' 11'')
1.3m (4' 3'')
1.0m (3' 3'')
0.7m (2' 4'')
1.8m (5' 11'')
1.3m (4' 3'')
1.2m (3' 11'')
0.9m (2' 11'')
0.9m (2' 11'')
0.8m (2' 7'')
0.7m (2' 4'')
0.6m (1' 12'')
0.5m (1' 8'')
0.3m (' 12'')
200" (508cm) 10.5m (34' 6'')
150" (381cm) 7.9m (25'10'')
133" (338cm) 7.0m (22'11'')
3.2m (10'6'')
2.4m (7' 10'')
2.1m (6' 11'')
2.6m (8' 6'')
2.0m (6' 7'')
1.7m (5' 7'')
1.4m (4' 7'')
1.3m (4' 3'')
1.2m (3' 11'')
1.1m (3' 7'')
0.9m (2' 11'')
0.7m (2' 4'')
0.5m (1' 8'')
8.7m (28' 7'')
6.5m (21' 5'')
5.8m (18'12'')
4.6m (15' 1'')
4.3m (14' 3'')
4.0m (13' 1'')
3.6m (11'11'')
3.1m (10' 3'')
2.6m (8' 6'')
1.7m (5' 7'')
2.3m (7' 7'')
1.7m (5' 7'')
1.5m (4' 11'')
2.5m (8' 2'')
1.9m (6' 3'')
1.7m (5' 7'')
1.8m (5' 11'') 1.5m (4' 11'')
1.3m (4' 3'') 1.1m (3' 7'')
16
1.2m (3' 11'') 1.0m (3' 3'')
106" (269cm) 5.6m (18' 3'') 1.7m (5' 7'')
1.6m (5' 3'' )
1.2m (3' 11'') 1.3m (4' 3'')
0.9m (2' 11'') 0.8m (2' 7'')
1.1m (3' 7'')
1.2m (3' 11'') 0.9m (2' 11'') 0.7m (2' 4'')
100" (254cm) 5.2m (17' 2'')
9
92" (234cm) 4.8m (15'10'') 1.4m (4' 7'')
84" (213cm) 4.4m (14' 5'') 1.3m (4' 3'')
72" (183cm) 3.8m (12' 4'') 1.1m (3' 7'')
60" (152cm) 3.1m (10' 3'') 0.9m (2' 11'')
40" (102cm) 2.1m ( 6' 10'') 0.6m (1' 12'')
1.0m (3' 3'') 1.1m (3' 7'')
0.9m (2' 11'') 1.0m (3' 3'')
0.8m (2' 7'') 0.7m (2' 4'')
0.7m (2' 4'') 0.6m (1' 12'')
: Picture area
0.8m (2' 7'')
0.9m (2' 11'') 0.6m (1' 12'') 0.5m (1' 8'')
0.7m (2' 4'') 0.7m (2' 4'')
0.4m (1' 4'') 0.4m (1' 4'')
0.5m (1' 8'') 0.4m (1' 4'')
0.3m (1' 12'') 0.2m (' 8'')
(a) = (0.052833802
(b) =(0.043798292
x
- 0.038639669)
- 0.038804856)
x: Screen size (diag.) (in)
x
When using a normal
screen (4:3)
Projection distance and Keystone correction
Screen size
(4:3)(x)
Maximum projection distance
Horizontal Placement range (c)
Minimum projection distance
In case of setting the
16:9 picture to the full
horizontal width of the
4:3 screen.
Horizontal Placement range (d)
Composite, S-video
RGB
480 /P, 1080
Vertical
placement range
Vertical
placement range
(f)
Projection
distance (a)
Projection
distance (b)
Diag.
Composite, S-video
720P
RGB
720P
(e)
480
I
/P, 1080
I
I
I
200" (508cm)
8.0m (26' 3'') 2.1m (6' 11'') 2.3m (7' 7'') 1.6m (5' 3'') 1.4m (4' 7'')
6.0m (19' 8'') 1.6m (5' 3'') 1.7m (5' 7'') 1.2m (3' 11'') 1.0m (3' 3'')
4.0m (13' 1'') 1.0m (3' 3'') 1.1m (3' 7'') 0.8m (2' 7'') 0.7m (2' 4'')
3.3m (10' 11'') 0.9m (2' 11'') 0.9m (2' 11'') 0.6m (1' 12'') 0.5m (1' 8'')
2.9m (9' 4'') 0.7m (2' 4'') 0.8m (2' 7'') 0.5m (1' 8'') 0.5m (1' 8'')
2.4m (7' 9'') 0.6m (1' 12'') 0.6m (1' 12'') 0.4m (1' 4'') 0.4m (1' 4'')
1.6m (5' 2'') 0.4m (1' 4'') 0.4m (1' 4'') 0.3m (1' 12'') 0.2m (1' 8'')
–
–
–
–
–
150" (381cm)
100" (254cm)
84" (213cm)
72" (183cm)
60" (152cm)
40" (102cm)
7.2m (23' 9'') 2.2m (7' 3'')
4.8m (15' 9'') 1.4m (4' 7'')
2.5m (8' 2'') 1.8m (5' 11'') 1.2m (3' 11'')
1.6m (5' 3'' ) 1.2m (3' 11'') 0.8m (2' 7'')
4
4.0m (13' 3'') 1.2m (3'11'') 1.4m (4' 7'') 1.0m (3' 3'') 0.7m (2' 4'')
3.5m (11' 4'') 1.0m (3' 3'')
2.9m (9' 5'') 0.8m (2' 7'')
1.9m (6' 3'') 0.5m (1' 8'')
1.2m (3' 11'') 0.8m (2' 7'') 0.6m (1' 12'')
0.9m (2' 11'') 0.7m (2' 4'') 0.5m (1' 8'')
0.4m (1' 4'') 0.4m (1' 4'') 0.3m (' 12'')
3
(a) = (0.04849498
x
- 0.038639669)
- 0.038804856)
x: Screen size (diag.) (in)
(b) =(0.040201488
x
: Screen area
: Picture area
-26
Download from Www.Somanuals.com. All Manuals Search And Download.
Upper and Lower Lens Shift Position
• This projector is equipped with a lens shift function that lets you adjust the projection height.
• Adjust the projection height to match the setup configuration.
• The screen can be moved maximum the length of one screen vertically using the lens shift.
Note
• Optimal image quality is produced with the projector positioned perpendicular to the screen with all feet flat and level.
Tilting or angling the projector will reduce the effectiveness of the lens shift function.
Screen size: 254 cm
Aspect ratio: 16:9
Screen
Lens centre
Lower lens shift position
(High mount setup)
90°
Lens centre
90°
Upper lens shift position
(Desktop setup)
Lower edge of screen (White portion) =
Standard (0) point
Upper and Lower Lens Shift Position (Ceiling Mount)
When the projector is in the inverted position, use the upper edge of the screen as the base line,
and exchange the lower and upper lens shift values.
Screen size: 254 cm
Aspect ratio: 16:9
Screen
90°
90°
-27
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
Image Projection
Rear Projection
When using the default setting.
MOn-screen Display
I Place a translucent screen between the projector and the au-
dience.
I Use the projector’s menu screen to reverse the projected im-
age. (See page 56
for use of this func-
tion.)
Note
• Optimal image quality can be achieved when the projector is
positioned perpendicular to the screen with all feet flat and lev-
eled.
The image is reversed.
Projection using a mirror
I Place a mirror (normal flat type) in front of the lens.
Info
• When using a mirror, be sure to carefully position both the
projector and the mirror so the light does not shine into the
eyes of the audience.
Ceiling-mount setup
I It is recommended that you use the optional Sharp ceiling-mount
bracket for this installation.
I Before mounting the
When using the default setting.
MOn-screen Display
projector, remove the
Swivel Stand. (See pages
24 and 25 for removing and
attaching the Swivel Stand.)
I Before mounting the
projector, contact your
nearest Sharp Authorised
Projector Dealer or Service
Centre to obtain the recommended ceiling-mount bracket (sold
separately). (AN-TK202 ceiling-mount bracket, AN-TK201
extension tube,AN-60KT ceiling adaptors forAN-TK202 orAN-
TK201)
The image is inverted.
I When the projector is in the inverted position, use the upper
edge of the screen as the base line.
I Use the projector’s menu screen to select the appropriate pro-
jection mode. (See page 56 for use of this function.)
-28
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Projection
Basic Procedure
Connect the required external equipment to
the projector before operating the following
procedures.
LAMP indicator
TEMP.
LAMP
POWER
Info
•
The language preset at the factory is English.
If you want to change the on-screen display
to another language, reset the language ac-
cording to the procedure on page 31.
POWER indicator
1 Plug the power cord into the
ON button
INPUT button
wall outlet.
• The POWER indicator illuminates red,
and the projector enters standby mode.
2
Press
or
on the remote control
on the projector.
• The blinking green LAMP indicator
shows that the lamp is warming up.
Wait until the indicator stops blinking
before operating the projector.
• If the power is turned off and then im-
mediately turned on again, it may take
a short while before the lamp turns on.
Note
• After the projector is unpacked and
turned on for the first time, a slight
odour may be emitted from the ex-
haust ventilative holes. This odor will
soon disappear with use.
ON button
When the power is on, the LAMP in-
dicator illuminates, indicating the sta-
tus of the lamp.
INPUT buttons
Green: Lamp is ready.
Green blinking: Warming up. / Cooling
down.
Red: Change the lamp.
-30
Download from Www.Somanuals.com. All Manuals Search And Download.
"On-screen Display (Example)
3 Press
,
,
,
or
on the remote control or
on
the projector to select the IN-
PUT mode.
INPUT 1 Mode
•
After pressing
once on the projector,
use to select the desired input mode.
INPUT 2 Mode
INPUT 3 Mode
Note
• When no signal is received, “NO SIG-
NAL” will be displayed. When a sig-
nal that the projector is not preset to
receive is received, “NOT REG.” will
be displayed.
About the INPUT modes
INPUT 1 Used for projecting im-
(Compo- ages from equipment
nent)
connected to INPUT 1
terminals.
INPUT 4 Mode
INPUT 2 Used for projecting im-
(Compo- ages from equipment
nent/RGB) connected to INPUT 2
terminal.
INPUT 3 Used for projecting im-
(S-Video) ages from equipment
connected to INPUT 3
terminal.
DIGITAL INPUT Mode
INPUT 4 Used for projecting im-
(Video)
ages from equipment
connected to INPUT 4
terminal.
DIGITAL
Used for projecting
images from equipment
connected to DIGITAL
INPUT terminal.
Selecting the On-
screen Display Lan-
guage
On-screen Display
English is the preset language for the On-
screen Display; however, this can be changed
to German, Spanish, Dutch, French, Italian,
Swedish, Portuguese, Chinese, Korean or
Japanese.
Display the “Language” menu and se-
lect the desired Language.
➝For operating the menu screen, see
pages 38 to 41.
-31
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Projection
STANDBY button
Turning the Power off
1 Press
trol or
on the remote con-
on the projector,
then press
or
again
while the confirmation message
is displayed, to put the projec-
tor into the standby mode.
• A dimly-lit screen is displayed for a
short time to reduce lamp damage.
Note
• If you accidentally pressed
and do not want to put the projector
into the standby mode, wait until the
confirmation message disappears.
STANDBY button
2
Unplug the power cord from the
AC outlet after the cooling fan
stops.
Info
• Do not unplug the power cord dur-
ing projection or cooling fan opera-
tion. This can cause damage due
to the rise in internal temperature,
as the cooling fan also stops.
• When connected to equipment such
as an amplifier, be sure to turn off
the power to the equipment con-
nected first and then to the projec-
tor.
-32
Download from Www.Somanuals.com. All Manuals Search And Download.
KEYSTONE button
Keystone Correction
This function can be used to adjust the Key-
stone settings.
Note
• For details about using the menu screen,
see pages 38 to 41.
", ',\, |
buttons
1 Press
on the projector or
on the remote control.
2 Press
/
to select “H Key-
stone” or “V Keystone”.
Selected Item
H Keystone
V Keystone
Reset
Description
Horizontally adjusts the keystone settings.
Vertically adjusts the keystone settings.
V and H Keystone adjustments are
returned to the factory preset settings.
KEYSTONE button
", ',\, |
buttons
3 Press
/
to move the mark
on the selected adjustment
item to the desired setting.
Note
• Straight lines and the edges of the
displayed image may appear
jagged, when adjusting the Key-
stone setting.
• When adjusting “H Keystone” and
“V Keystone” at the same time, the
values of adjustable angles for each
setting become smaller.
• The adjustable value of the “V Key-
stone” becomes extremely small
when “H Keystone” is made to be
the maximum value.
Horizontal Keystone Correction
• Keystone correction is disabled
while the picture mode is set to
“SMART STRETCH”. (See page
35.)
4 To return to the normal screen,
Vertical Keystone Correction
press
again.
-33
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Projection
Placement of the Pro-
jected Image Using the
Keystone Correction
Place the projector at a distance from the
screen that allows images to be projected onto
the screen by referring to “Adjusting the Pro-
jection Distance” on pages 26 and 27.
: Screen area
1 Project the test pattern of the
Keystone correction function
onto the screen. Rotate the Fo-
cus ring until the image on the
screen comes into focus. (See
page 25.)
2 Change the projection angle
using the Swivel Stand to prop-
erly project images onto the
screen. (See page 24).
3 Align the edge of the screen
closest to the projector with
the test pattern by adjusting
the zoom and the Swivel Stand.
(See pages 24 and 25.)
4 Adjust the Keystone function
so that the size of the projected
image matches the screen
size. (See page 33.)
5 Align the image on the screen
by adjusting the zoom function
and the Swivel Stand.
6 Adjust the focus so that the
projected image is in focus at
the centre of the screen. (See
page 25.)
Note
• The aspect ratio of the projected image
shifts slightly when the lens shift is at a
position other than the top position.
• The aspect ratio of the projected image
also shifts slightly when the “H Keystone”
and “V Keystone” functions are adjusted
simultaneously.
-34
Download from Www.Somanuals.com. All Manuals Search And Download.
Freezing a Moving
Image
You can instantly freeze a moving image with
the remote control.
1 Press
.
• The projected image is frozen.
FREEZE button
2 Press
again to return to the
moving image from the cur-
rently connected device.
Adjusting the Picture
Aspect Ratio
RESIZE button
This function allows you to modify or custom-
ize the picture display mode to enhance the
input image. Depending on the input signal,
you can choose SIDE BAR, SMART STRETCH,
CINEMA ZOOM or STRETCH image.
Press
. Each time
is pressed,
the picture mode changes as
shown on the next page.
RESIZE button
-35
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Projection
SMART
STRETCH
CINEMA
ZOOM
SIDE BAR
STRETCH
480
480P
576
I
I
VGA
SVGA
XGA
For 4:3
aspect ratio
768
ן 576 1024
ן 576 1024
ן 576 1024
ן 576 576P
NTSC
PAL
SECAM
480P
720P
768
ן 576 1024
ן 576 1024
ן 576 1024
ן 576 1024
ן 576 1024
ן 576 For 16:9
aspect ratio
–
–
–
–
–
–
1080
I
• “STRETCH” is fixed when 540P, 720P or 1080I signal is entered.
• “SMART STRETCH” cannot be selected while input signal from a computer (VGA, SVGA or XGA) is entered.
Output screen image
Input Signal
SIDE BAR
SMART STRETCH
CINEMA ZOOM
STRETCH
4:3 aspect ratio
480
480P
576
I
I
576P
NTSC
PAL
SECAM
Letterbox
Squeeze
540P
1080
I
16:9 aspect ratio
720P
VGA
SVGA
XGA
4:3 aspect ratio
Note
• “SMART STRETCH” cannot be selected while the Keystone correction (page 33) is being adjusted.
• Keystone correction (page 33) is disabled while the picture mode is set to “SMART STRETCH”.
• 580I/580P is displayed on the screen when signal 576I/576P is input.
-36
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjustments and Settings
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menu Screen
The menu screens allow you to adjust the image and various projector settings.
The menu can be operated to achieve two functions, adjustment and setting.
(For adjusting the menu items, see pages 38 and 39. For setting the menu items, see pages
40 and 41.)
Menu screen (example)
", ', \, | buttons
Menu Selections
(Adjustments)
MENU button
UNDO button
1 Press
.
• The menu screen is displayed.
Note
• The “Picture” menu screen for the
selected input mode is displayed.
ENTER button
", ', \, | buttons
MENU button
UNDO button
ENTER button
-38
Download from Www.Somanuals.com. All Manuals Search And Download.
Select the menu icon.
2 Press \ or | to display the
other menu screens.
• The menu icon for the selected menu
screen is highlighted.
Menu icon
Menu screen
Picture
Fine Sync
Options
Language
PRJ Mode
Note
• The “Fine Sync” menu is not avail-
able for INPUT 3 or 4.
• For items on the menus, see the
tree charts on pages 42 and 43.
3 Press " or ' to select the item
you want to adjust.
Select
the item.
Note
• To display a single adjustment item,
press
after selecting the item.
Only the menu bar and the selected
adjustment item will be displayed.
Then if you press " or ', the fol-
lowing item (“Bright” after “Con-
trast”) will be displayed.
• Press
screen.
to return to the previous
4 Press \ or | to adjust the item
selected.
• The adjustment is stored.
Adjust the item.
5 Press
.
• The menu screen will disappear.
-39
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menu Screen
", ', \, | buttons
UNDO button
Menu Selections
(Settings)
MENU button
1 Press
.
• The menu screen is displayed.
Note
• The “Picture” menu screen for the
selected input mode is displayed.
ENTER button
", ', \, | buttons
MENU button
ENTER button
UNDO button
2 Press \ or | to display the
Select the menu icon.
other menu screens.
• The menu icon for the selected menu
screen is highlighted.
Menu icon
Menu screen
Picture
Fine Sync
Options
Language
PRJ Mode
Note
• The “Fine Sync” menu is not avail-
able for INPUT 3 or 4.
• For items on the menus, see the
tree charts on pages 42 and 43.
-40
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Press " or ' to select the
item you want to set.
Select
the item.
Note
• Press
screen.
to return to the previous
• In some menus, select the icon us-
ing “
”.
4 Press |.
• The sub menu is displayed.
Sub
menu
5 Press " or ' to select the set-
ting of the item displayed in the
sub menu.
Sub
menu
6 Press
.
• The item selected is set.
7 Press
.
• The menu screen will disappear.
-41
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Bar Items
I INPUT 1 / 2 / DIGITAL INPUT Mode
Sub menu
Main menu
Main menu
Picture (
)
Contrast
Bright
Color
מ 30 ם 30 מ 30 ם 30 מ 30 ם 30 מ 30 ם 30 מ 30 ם 30 מ 30 ם 30 מ 30 ם 30 Language (
)
English
Deutsch
Español
Nederlands
Français
Italiano
Tint
Sharp
Red
Blue
Svenska
Português
Reset
CLR Temp
5500k
6500k
7500k
8500k
9300k
10500k
0
0
0
0
0
0
10
10
10
10
10
10
PRJ Mode (
)
Front
Ceiling
ם Front Rear
Gamma
Ceiling
ם Rear Standard
Cinema 1
Cinema 2
Cinema 3
White Emphasis [ON/OFF]
Picture Setting
Memory 1
Memory 2
Memory 3
Memory 4
Memory 5
Memory OFF
Fine Sync (
)
Clock
Phase
H-Pos
V-Pos
Reset
מ 30 ם 30 מ 15 ם 15 מ 30 ם 30 מ 30 ם 30 640
ן 480 720
ן 480 480P
Special Modes
Auto Sync
Signal Info
[ON/OFF]
Resolution 640
ן 480 Hor Freq
Vert Freq
37.5 kHz
72 Hz
Options (
)
Lamp Timer (Life)
OSD Display [ON/OFF]
RGB
Signal Type
Component
Background [None/Blue]
Eco Mode [Eco/Standard]
Auto Power Off [ON/OFF]
Menu Position
Note
• The resolution, vertical frequency and horizontal
frequency figures displayed above are for
example purposes only.
• “Color”, “Tint”, and “Sharp” do not appear when
“RGB” is selected in INPUT 2 mode.
• “Signal Type” is not displayed when using
INPUT 1.
Center
Upper Right
Lower Right
Upper Left
Lower Left
Menu Color [Opaque/Translucent]
• “Color”, “Tint”, “Sharp”, “Clock”, “Phase”, “H-
Pos”, “V-Pos”, “Special Modes” and “Auto Sync”
cannot be used in the DIGITAL INPUT mode.
• “Clock”, “Phase” and “Auto Sync” cannot be
used in the Component mode.
-42
Download from Www.Somanuals.com. All Manuals Search And Download.
I INPUT 3 / 4 Mode
Sub menu
Main menu
Main menu
Picture (
)
Contrast
Bright
Color
מ 30 ם 30 מ 30 ם 30 מ 30 ם 30 מ 30 ם 30 מ 30 ם 30 מ 30 ם 30 מ 30 ם 30 Language (
)
English
Deutsch
Español
Nederlands
Français
Italiano
Tint
Sharp
Red
Blue
Svenska
Português
Reset
CLR Temp
5500K
0
0
0
0
0
0
10
10
10
10
10
10
6500K
7500K
8500K
9300K
10500K
Standard
Cinema1
Cinema2
Cinema3
PRJ Mode (
)
Front
Ceiling
ם Front Rear
Gamma
Ceiling
ם Rear White Emphasis [ON/OFF]
Picture Setting
Memory1
Memory2
Memory3
Memory4
Memory5
MemoryOFF
Options (
)
Lamp Timer (Life)
OSD Display [ON/OFF]
Video System
Auto
PAL
NTSC3.58
SECAM
NTSC4.43
PAL–M
PAL–N
PAL–60
Background [None/Blue]
Eco Mode [Eco/Standard]
Auto Power Off [ON/OFF]
Menu Position
Center
Upper Right
Lower Right
Upper Left
Lower Left
Note
• “Tint” cannot be used with PAL, SECAM, PAL-M,
PAL-N or PAL-60.
Menu Color [Opaque/Translucent]
-43
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Picture
You can adjust the projector’s picture to your preferences with the following picture set-
tings.
On-screen Display
Adjusting Image Prefer-
ences
Note
• First select “Memory 1-5” or “Memory
OFF” when you want to save the “Picture”
menu settings. See page 47 for details.
Adjust the “Picture” menu on the menu
screen.
➝For operating the menu screen, see
pages 38 to 41.
Selected Item
Description
\ button
| button
Contrast
Bright
Color
Tint
For adjusting the contrast level
For less contrast
For more contrast
For adjusting the brightness of an image
For adjusting the colour intensity of an image
For adjusting the tones of an image
For less brightness
For more brightness
For less colour intensity For more colour intensity
Skin tones become purplish
Skin tones become greenish
For more sharpness
For stronger red
Sharp
Red
For making sharper or softer the contour of an image For less sharpness
For adjusting the redness of an image
For adjusting the blueness of an image
For weaker red
For weaker blue
Blue
For stronger blue
Note
• “Color”, “Tint” and “Sharp” do not appear
for RGB input in INPUT 2 mode.
• To reset all adjustment items, select “Re-
set” on the “Picture” menu screen and
press
.
• “Tint” cannot be used with PAL, SECAM,
PAL-M, PAL-N or PAL-60.
• “Color”, “Tint” and “Sharp” cannot be used
in the DIGITAL INPUT mode.
-44
Download from Www.Somanuals.com. All Manuals Search And Download.
On-screen Display
Adjusting the Colour
Temperature
This function allows for selecting the desired
colour temperature. With the lower value se-
lected, the projected image becomes warmer,
reddish and incandescent-like while with the
higher value, the image becomes cooler, blu-
ish and fluorescent-like.
Select “CLR Temp” in the “Picture”
menu on the menu screen.
➝For operating the menu screen, see
pages 38 to 41.
Description
Selected Item
The less the value is set to, the
warmer, reddish, incandescent-like
the image becomes.
5500K
6500K
7500K
8500K
9300K
10500K
The more the value is set to, the
cooler, bluish, fluorescent-like the
image becomes.
“CLR Temp” is fine adjusted by following the
procedure below.
1 Select “CLR Temp” in the “Pic-
ture” menu on the menu
screen and press
.
• A single menu bar of “CLR Temp” is
displayed.
2 Press ' or " to fine adjust the
colour temperature.
• With the lower value selected, the pro-
jected image becomes magenta-
tinged. With the higher value selected,
the projected image becomes green-
tinged.
• Pressing \ or | changes the value
of the colour temperature in the sub
menu.
Note
•Values on “CLR Temp” are only for gen-
eral standard purposes.
-45
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Picture
On-screen Display
Gamma Correction
Function
Gamma is an image quality enhancement
function.
Four gamma settings are available to allow for
differences in the brightness of the room.
Select “Gamma” in the “Picture” menu
on the menu screen.
➝For operating the menu screen, see
pages 38 to 41.
Description
Selected Item
Standard Standard picture without gamma
correction
Cinema 1 Gives greater depth to darker portions
of images.
Cinema 2 Brightness is toned down and the
image becomes more balanced.
Cinema 3 Brighten the darker portions of images
for easier viewing in a dimly lit room.
On-screen Display
Emphasizing the
Contrast
This function emphasizes the bright portions
of images to obtain a higher contrast image.
Select “White Emphasis” in the “Pic-
ture” menu on the menu screen.
➝For operating the menu screen, see
pages 38 to 41.
Description
Selected Item
(ON) For emphasizing the bright portions of
images
(OFF) For disabling “White Emphasis”
-46
Download from Www.Somanuals.com. All Manuals Search And Download.
On-screen Display
Picture Setting
Function
This function stores all items set in “Picture”.
Five settings can be stored separately in
“Memory 1” to “Memory 5”. Each stored set-
ting is reassigned to each input mode (INPUT
1 to INPUT 4 and DIGITAL).
Even when the input mode or signal is
changed, you can easily select optimal set-
tings from the stored settings.
I
Storing theAdjustment Values
for Each Memory Number
Select “Picture Setting” on the “Picture”
menu and the memory location where
you want to store the settings. Then
adjust the setting items on the “Picture”
menu.
➝For operating the menu screen, see
pages 38 to 41.
Description
Selected Item
Memory Settings of all items in “Picture” can be
PICTURE SETTING button
1-5
stored for the respective input modes.
The stored settings can be selected in
any input modes.
Memory Besides “Memory 1” to “Memory 5”,
OFF
other settings on the “Picture” menu
can be stored for each input mode.
The settings stored in “Memory OFF”
cannot be applied when another input
mode is selected.
IApplying the Stored Settings
If you want to apply the stored settings
on the “Picture” menu, select “Picture
Setting” on the “Picture” menu and the
memory location where you have
stored the settings.
Note
• This function can be operated using the
on the projector or
on the remote
control, as well as the OSD menu screen.
Each time or is pressed, the
memory number changes as shown be-
low.
PICTURE SETTING
button
Memory 1
Memory 2
Memory 5
Memory 3
Memory 4
Memory OFF
-47
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Computer and DVD/DTV Images
Use the Fine Sync function in case of irregularities such as vertical stripes or flickering in
portions of the screen.
On-screen Display
When Auto Sync is OFF
When “Auto Sync” is “OFF”, interference such
as flickering or vertical stripes may occur if
displaying tilings or vertical stripes. Should
this occur, adjust “Clock”, “Phase”, “H-Pos”
and “V-Pos” for obtaining an optimum image.
Select “Clock”, “Phase”, “H-Pos” or “V-
Pos” in the “Fine Sync” menu on the
menu screen.
➝For operating the menu screen, see
pages 38 to 41.
Selected Item
Description
Clock
Phase
H-Pos
Adjusts vertical noise.
Adjusts horizontal noise (similar to tracking on your VCR).
Centres the on-screen image by moving it to the left or right.
V-Pos
Centres the on-screen image by moving it up or down.
Note
• “Clock”, “Phase”, “H-Pos” and “V-Pos” can-
not be used in the DIGITAL INPUT mode.
• “Clock” and “Phase” cannot be used in the
Component mode.
• Computer image adjustments can be
AUTO SYNC
made easily by pressing
on the re-
mote control. See page 50 for details.
• To reset all adjustment items, select “Re-
set” on the “Fine Sync” menu screen and
press
.
• The adjustable area of each item may be
changed according to the input signal.
-48
Download from Www.Somanuals.com. All Manuals Search And Download.
On-screen Display
Special Modes Adjust-
ment
Ordinarily, the type of input signal is detected
and the correct resolution mode is automati-
cally selected. However, for some signals, the
optimal resolution mode in “Special Modes”
on the “Fine Sync” menu screen may need
to be selected to match the computer display
mode.
Set the resolution by selecting “Special
Modes” in the “Fine Sync” menu on the
menu screen.
➝For operating the menu screen, see
pages 38 to 41.
Note
• Avoid displaying computer patterns which
repeat every other line (horizontal
stripes). (Flickering may occur, making
the image hard to see.)
• When inputting DTV 1080I signal, select
the corresponding type of signal.
• When inputting 720P signal from the
video equipment, select “720P”. When
inputting 1280 × 720 signal from the com-
puter, select “HTPC”.
• “Special Modes” cannot be used in the
DIGITAL INPUT mode.
-49
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Computer and DVD/DTV Images
On-screen Display
Auto Sync Adjustment
Used to automatically adjust a computer im-
age.
Select whether the image is to be synchro-
nized automatically when switching the sig-
nal with “ON” or “OFF”.
Select “Auto Sync” in the “Fine Sync”
menu on the menu screen.
➝For operating the menu screen, see
pages 38 to 41.
Selected Item
Description
Auto Sync adjustment will occur
when the projector is turned on or
when the input signals are switched,
when connected to a computer.
(ON)
Auto Sync adjustment is not
automatically performed.
(OFF)
Note
• When the optimum image cannot be
achieved withAuto Sync adjustment, use
manual adjustments. (See page 48.)
• The Auto Sync adjustment may take
some time to complete, depending on the
image of the computer connected to the
projector.
AUTO SYNC button
• “Auto Sync” cannot be used in the DIGI-
TAL INPUT mode.
• Auto Sync adjustment is also performed
AUTO SYNC
by pressing
on the remote control.
On-screen Display
Checking the Input Signal
This function allows you to check the current
input signal information.
Select “Signal Info” in the “Fine Sync”
menu on the menu screen.
➝For operating the menu screen, see
pages 38 to 41.
Note
• 540P is displayed on the screen when
signal 1080I is inputted during DVI con-
nection.
-50
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the “Options” Menu
On-screen Display
Checking the Lamp Life
Status
You can confirm the cumulative lamp usage
time and the remaining lamp life (percentage).
Display the “Options” menu to check
the lamp life status.
➝For operating the menu screen, see
pages 38 to 41.
Remaining lamp life
Lamp usage condition
100%
5%
Operated exclusively
in Eco mode
Operated exclusively
Approx.
Approx.
(
)
4,000 hours 200 hours
Approx. Approx.
3,000 hours 150 hours
in Standard mode
(
)
Note
• It is recommended that the lamp be
changed when the remaining lamp life
becomes 5%.
For lamp replacement, contact your near-
est Sharp Authorised Projector Dealer or
Service Centre.
• The table above indicates rough estimates
in the case of using only in each mode
shown. Remaining lamp life changes within
the range of the values shown depending
on the frequency at which “Eco Mode” is
switched to “ ” (Eco mode) and “
(Standard mode) (see page 53).
”
On-screen Display
Turning on/off the On-
screen Display
This function allows you to turn on or off the
on-screen messages that appear during input
select.
Select “OSD Display” in the “Options”
menu on the menu screen.
➝For operating the menu screen, see
pages 38 to 41.
Description
Selected Item
(ON) All On-screen Displays are
displayed.
(OFF) INPUT/FREEZE/AUTO SYNC/
“An invalid button has been
pressed.” are not displayed.
-51
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the “Options” Menu
On-screen Display
Selecting the Signal
Type
This function allows you to select the input
signal type Component or RGB for INPUT 2.
Select “Signal Type” in the “Options”
menu on the menu screen.
➝For operating the menu screen, see
pages 38 to 41.
Description
Selected Item
RGB
Set when RGB signals are
received.
Set when Component signals
are received.
Component
RGB/COMP. button
Note
• “RGB” or “Component” can be selected
with
on the remote control only in
INPUT 2.
On-screen Display
Setting the Video Signal
(VIDEO menu only)
The video input system mode is preset to
“Auto”; however, it can be changed to a spe-
cific system mode if the selected system mode
is not compatible with the connected audiovi-
sual equipment.
Select “Video System” in the “Options”
menu on the menu screen.
➝For operating the menu screen, see
pages 38 to 41.
Note
• When the system mode is set to “Auto”,
you may not receive a clear picture due
to signal differences. Should this occur,
switch to the video system of the source
signal.
• “Auto” cannot be set for PAL-M and PAL-
N input signals. Select “PAL-M” or “PAL-
N” in “Video System” menu for PAL-M and
PAL-N input signals.
-52
Download from Www.Somanuals.com. All Manuals Search And Download.
On-screen Display
Selecting a
Background Image
This function allows you to select the image
displayed when no signal is being sent to the
projector.
Select “Background” in the “Options”
menu on the menu screen.
➝For operating the menu screen, see
pages 38 to 41.
Description
(Blue) Blue screen
Selected Item
(None) Black screen
On-screen Display
Setting the Eco Mode
This function allows you to select the desired
power consumption mode.
Select “Eco Mode” in the “Options”
menu on the menu screen.
➝For operating the menu screen, see
pages 38 to 41.
Selected Item Brightness
Lamp life
Power consumption
Approx.
80%
230 W
285 W
(Eco mode)
4,000 hours
Approx.
3,000 hours
100%
(Standard mode)
Note
• Although lamp life and noise are improved
when “Eco Mode” is set to “ ” (Eco
mode), brightness decreases by 20%.
• “Eco Mode” is factory preset to “ ” (Stan-
dard mode).
-53
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the “Options” Menu
On-screen Display
Automatic Power Shut-
off Function
When no input signal is detected for more than
15 minutes, the projector will automatically en-
ter the standby mode if set to “ ” (ON).
Select “Auto Power Off” in the “Options”
menu on the menu screen.
➝For operating the menu screen, see
pages 38 to 41.
Description
Selected Item
Projector automatically enters the
standby mode after 15 minutes
without an input signal.
Automatic Power Shut-off disabled.
Note
• “Auto Power Off” is factory preset to “ ”.
When the Auto Power Off function is set to
(ON)”, 5 minutes before the projector
•
“
enters the standby mode, the message “En-
ter STANDBY mode in X min.” will appear on
the screen to indicate the remaining minutes.
On-screen Display
Selecting the Menu
Screen Position
This function allows you to select the desired
position of the menu screen.
Select “Menu Position” in the “Options”
menu on the menu screen.
➝For operating the menu screen, see
pages 38 to 41.
Selected Item
Description
Center
The menu is displayed on the
center of the image.
Upper
Right
The menu is displayed on the
upper right of the image.
Lower
Right
The menu is displayed on the
lower right of the image.
Upper
Left
The menu is displayed on the
upper left of the image.
Lower
Left
The menu is displayed on the
lower left of the image.
-54
Download from Www.Somanuals.com. All Manuals Search And Download.
On-screen Display
Selecting the Menu
Colour
This function allows you to select the colour
of the menu screen.
Select “Menu Color” in the “Options”
menu on the menu screen.
➝For operating the menu screen, see
pages 38 to 41.
Description
Selected Item
(Opaque)
The menu is displayed
opaquely.
The menu is displayed
translucently. The part of the
menu on the image becomes
transparent.
(Translucent)
-55
Download from Www.Somanuals.com. All Manuals Search And Download.
Reversing/Inverting Projected Images
This projector is equipped with a reverse/invert image function that allows you to reverse or
invert the projected image for various applications.
On-screen Display
Setting the Projection
Mode
Display the “PRJ Mode” menu and se-
lect the desired projection mode.
➝For operating the menu screen, see
pages 38 to 41.
Selected Item
Front
Description
Normal image
Ceiling + Front Inverted image
Rear Reversed image
Ceiling + Rear Reversed and inverted image
Note
•
This function is used for the reversed im-
age and ceiling-mount setups. See page 28
for these setups.
-56
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance Indicators
I The warning lights on the projector indicate problems inside the projector.
I If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate
red, and the projector will enter the standby mode. After the projector has entered the standby
mode, follow the procedures given below.
About the lamp indicator
TEMP.
LAMP
POWER
TEMPERATURE LAMP
POWER
indicator
IThe lamp life becomes 0%, when used
for approximately 4,000 hours with “Eco
mode” or when used for approximately
3,000 hours with “Standard mode” (see
page 53).
IWhen the remaining lamp life becomes
5% or less, “ ” (yellow) will be displayed
on the screen. When the percentage be-
comes 0%, “ ” will change to “ ” (red),
the lamp will automatically turn off and
then the projector will automatically en-
ter the standby mode. At this time, the
lamp indicator will illuminate in red.
IIf you try to turn on the projector a fourth
time without replacing the lamp, the pro-
jector will not turn on.
WARNING
indicator
indicator
About the temperature warning indicator
If the temperature inside the
projector increases, due to
blockage of the air vents, or the
setting location, “
” will
illuminate in the lower left corner of the picture. If
the temperature keeps on rising, the lamp will turn off
and the temperature warning indicator will blink, the
cooling fan will run for a further 90 seconds, and then
the projector will enter the standby mode. After
“
” appears, be sure to perform the following
measures.
Maintenance indicator
Condition
Problem
Possible Solution
Normal
Abnormal
• Relocate the projector to an area
with proper ventilation.
• Blocked air intake
The internal
temperature is
abnormally high.
• Cooling fan break-
down
• Internal circuit failure
• Clogged air intake
Temperature
warning
indicator
Red on/
Standby
• Take the projector to your nearest
Sharp Authorised Projector Dealer
or Service Centre for repair.
Off
• Carefully replace the lamp. (See
page 59.)
• Take the projector to your nearest
Sharp Authorised Projector Dealer
or Service Centre for repair.
• Please exercise care when
replacing the lamp.
• Remaining lamp life
Time to change
the lamp.
Green on Red on
Green blinks
becomes 5% or less.
Lamp
indicator
when the
lamp is
Red on/
The lamp does
not illuminate.
• Burnt-out lamp
• Lamp circuit failure
warming up. Standby
• Securely install the cover.
• If the power is not turned on even
when the lamp unit cover is
securely installed, contact your
nearest Sharp Authorised Projec-
tor Dealer or Service Centre for
advice.
The power is
not turned on.
Power
indicator
Green on/
Off
• The lamp unit cover
is open.
Red on
-58
Download from Www.Somanuals.com. All Manuals Search And Download.
Info
• If the temperature warning indicator illuminates, and the projector enters the standby mode, follow the pos-
sible solutions on the previous page and then wait until the projector has cooled down completely before
plugging in the power cord and turning the power back on. (At least 5 minutes.)
• If the power is turned off for a brief moment due to power outage or some other cause while using the
projector, and the power supply recovers immediately after that, the lamp indicator will illuminate in red and
the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace the power cord in the
AC outlet and then turn the power on again.
• If you want to clean the air vents during projector operation, be sure to put the projector into the standby
mode. After the cooling fan has stopped, clean the vents.
• The cooling fan keeps the internal temperatures of the projector constant and this function is controlled
automatically. The sound of the cooling fan may change during operation because the fan speed may change
and this is not a malfunction.
• Do not unplug the power cord after the projector has entered the standby mode and while the cooling fan is
running. The cooling fan runs for about 90 seconds.
Regarding the Lamp
Lamp
I It is recommended that the lamp (sold separately) be replaced when the remaining lamp life be-
comes 5% or less, or when you notice a significant deterioration in the picture and color quality.
The lamp life (percentage) can be checked with the on-screen display. See page 51.
I For lamp replacement, please consult your nearest Sharp Authorised Projector Dealer or Service Centre.
Caution Concerning the Lamp
I This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp
failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface
scratches or deterioration of the lamp due to a lapse of usage time. The period of time up to failure
largely varies depending on the individual lamp and/or the condition and the frequency of use. It is
important to note that failure can often result in the bulb cracking.
I When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended
that the lamp be replaced with a new one immediately, even if the lamp appears to be operating
normally.
I Should the lamp break, the glass particles may spread inside the lamp unit or gas contained in the
lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes
mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In
case of exposure to the gas, consult a doctor as soon as possible.
I Should the lamp break, there is also a possibility that glass particles may spread inside of the
projector. In such a case, it is recommended you contact your nearest Sharp Authorised Projector
Dealer or Service Centre to remove the damaged lamp and assure safe operation.
Replacing the Lamp
Caution
• Do not remove the lamp unit immediately after operation of the projector. The lamp will be hot and touching
it can lead to burn or injury.
• Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool
before removing the lamp unit.
I If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorised
Projector Dealer or Service Centre for repair. Purchase a replacement lamp unit of type BQC-
XVZ200++1 from your nearest Sharp Authorised Projector Dealer or Service Centre. Then carefully
change the lamp by following the instructions described in this section. If you wish, you may have
the lamp replaced at your nearest Sharp Authorised Projector Dealer or Service Centre.
-59
Download from Www.Somanuals.com. All Manuals Search And Download.
Regarding the Lamp
Removing and Install-
ing the Lamp Unit
Lamp
unit
BQC-XVZ200++1
Caution
• Be sure to remove the lamp unit by the handle.
Do not touch the glass surface of the lamp
unit or the inside of the projector.
STANDBY button
• To avoid injury to yourself and damage to the
lamp, carefully follow the steps below.
• Replace the lamp after turning off the power
and unplugging the power cord.
1 Put the projector into the
standby mode.
• Press
.
• Wait until the cooling fan stops.
2 Unplug the power cord.
• Unplug the power cord from the AC
socket.
Power cord
• Leave the lamp until it has fully cooled
down (about 1 hour).
3 Remove the Swivel Stand. (See
page 24.)
4 Remove the lamp unit cover.
• Loosen the user service screw that se-
cures the lamp unit cover.
User service
screw
• Slide the lamp unit cover in the direc-
tion of the arrow.
5 Remove the lamp unit.
• Loosen the securing screws from the
lamp unit. Hold the lamp unit by the
handle and pull it in the direction of
the arrow.
-60
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Insert the new lamp unit.
• Press the lamp unit firmly into the lamp
unit compartment. Fasten the secur-
ing screws.
7 Attach the lamp unit cover.
• Slide the lamp unit cover in the direc-
tion of the arrow.
• Fasten the user service screw.
Resetting the Lamp
Timer
Reset the lamp timer after replacing the lamp.
1 Plug the power cord.
• Confirm that the POWER indicator il-
luminates red.
Power cord
ON button
UNDO button
2 Reset the lamp timer.
• Press
,
,
,
,
and
INPUT button
in order. Then press
.
• “LAMP 0000H” is displayed on the
screen.
ENTER button
Info
• Make sure to reset the lamp timer only
when replacing the lamp. If you reset the
lamp timer and continue to use the same
lamp, the lamp may become damaged or
explode.
-61
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning the Ventilative Holes
• This projector is equipped with
Side and Rear view
Bottom view
ventilative holes to ensure the opti-
mal operating condition of the projec-
tor.
• Periodically clean the ventilative hole
by vacuuming it off with a vacuum
cleaner.
• The ventilative holes should be
cleaned every 100 hours of use. Clean
the ventilative holes more often when
the projector is used in a dirty or
smoky location.
Intake ventilative holes
Intake ventilative holes
Swivel stand
Intake ventilative holes
Cleaning the
Ventilative Holes
STANDBY button
1 Put the projector into the
standby mode.
• Press
.
• Wait until the cooling fan stops.
2 Unplug the power cord.
Power cord
3 Clean the dust off by putting
the cleaner hose on the intake
ventilative holes.
Cleaner hose
-62
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Kensington Lock
This projector has a Kensington Secu-
rity Standard connector for use with a
Kensington MicroSaver Security Sys-
tem. Refer to the information that came
with the system for instructions on how
to use it to secure the projector.
Rear View
Kensington Security
Standard connector
Troubleshooting
Problem
Check
No picture appears.
•Projector power cord is not plugged into the wall outlet.
•Selected input is wrong. (See page 31.)
•Cables incorrectly connected to back panel of the projector. (See pages
14–23.)
•“Contrast” and “Bright” adjustments are set to minimum position. (See
page 44.)
Colour is faded or poor.
Picture is blurred.
•Picture adjustments are not correct. (See page 44.)
•Adjust the focus. (See page 25.)
•Projection distance is too long or too short to allow for proper focus. (See
pages 26 and 27.)
No OSD appears.
•OSD Display is set to “OFF”, preventing to display some or all On-screen
Displays. (See page 51.)
An unusual sound is
occasionally heard from the
cabinet.
•If the picture is normal, the sound is due to cabinet shrinkage caused by
temperature changes. This will not affect operation or performance of the
projector.
Maintenance indicator
illuminates.
•Refer to “Maintenance Indicators” on page 58.
Picture noise appears.
•Adjust the “Phase” setting. (See page 48.)
Image is green on INPUT 2
Component.
•Change the input signal type. (See page 52.)
Image is pink (no green) on
INPUT 2 RGB.
-63
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Pin Assignments
DVI-I (INPUT 2 / DIGITAL INPUT) port : 29 pin connector
• DVI Digital INPUT
Pin No. Signal
Pin No. Signal
• •• • •• • ••
• •• •
• •• • •• • ••
• •• •
~
16
9
1
2
3
4
5
T.M.D.S data 2–
T.M.D.S data 2+
T.M.D.S data 2 shield
Not connected
Not connected
DDC clock
16
17
18
19
20
21
22
23
24
C1
C2
C3
C4
C5
Hot plug detection
~
1 2
7 8
T.M.D.S data 0–
T.M.D.S data 0+
T.M.D.S data 0 shield
Not connected
Not connected
T.M.D.S clock shield
T.M.D.S clock+
T.M.D.S clock–
Not connected
Not connected
Not connected
Not connected
Ground
C1
C2
C4
6
7
DDC data
C5
C3
8
9
Not connected
T.M.D.S data 1–
T.M.D.S data 1+
T.M.D.S data 1 shield
Not connected
Not connected
+5V power
17
24
10
11
12
13
14
15
• •• •
• •• •
~
18
23
Ground
• DVI Analog RGB Input
• DVI Analog Component Input
Pin No. Signal
Pin No. Signal
Pin No. Signal
Pin No. Signal
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Not connected
16
17
18
19
20
21
22
23
24
C1
C2
C3
C4
C5
Hot plug detection
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Analog input Red
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Not connected
16
17
18
19
20
21
22
23
24
C1
C2
C3
C4
C5
Not connected
Not connected
Not connected
Not connected
Not connected
DDC clock
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Ground
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Analog input Pr/Cr
Analog input Y
Analog input Pb/Cb
Not connected
Ground
DDC data
Vertical sync
Not connected
Not connected
Not connected
Not connected
Not connected
+5V power
Analog input Green
Analog input Blue
Horizontal sync
Ground
Ground
RS-232C Port: 9-pin D-sub male connector
Pin No. Signal Name
I/O
Reference
1
2
3
4
5
6
7
8
9
Not connected
1 2 3 4 5
RD
SD
Receive Data
Send Data
Reserved
Signal Ground
Reserved
Input
Output
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Not connected
SG
6 7 8 9
Reserved
Reserved
-64
Download from Www.Somanuals.com. All Manuals Search And Download.
(RS-232C) Specifications and Command Settings
PC control
A computer can be used to control the projector by connecting an RS-232C cable (null modem, cross type,
commercially available) to the projector. (See page 23 for connection.)
Communication conditions
Set the serial port settings of the computer to match that of the table.
Signal format: Conforms to RS-232C standard.
Baud rate: 9,600 bps
Data length: 8 bits
Parity bit: None
Stop bit: 1 bit
Flow control: None
Basic format
Commands from the computer are sent in the following order: command, parameter, and return code. After
the projector processes the command from the computer, it sends a response code to the computer.
Command format
C1 C2 C3 C4 P1 P2 P3 P4
Return code (0DH)
Command 4-digit
Parameter 4-digit
Response code format
Normal response
Problem response (communication error or incorrect command)
Return code (0DH)
O
K
E
R
R
Return code (0DH)
Info
• When more than one code is being sent, send each command only after the OK response code for the
previous command from the projector is verified.
Note
• When using the computer control function of the projector, the projector’s operating status cannot be read by
the computer. Therefore, confirm the status by transmitting the display commands for each adjustment
menu and checking the status with the on-screen display.
Commands
Example:
• When power on.
Computer
Projector
→
←
P
O
W
R
_
_
_
1
O
K
CONTROL CONTENTS
COMMAND PARAMETER
RETURN
OK OR ERR
POWER ON
STANDBY
P O W R _
P O W R _
_
_
_
_
_
_
_
_
_
_
_
_
_
_
1
0
1
2
3
4
5
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
INPUT 1 (COMPONENT 1)
INPUT 2 (COMPONENT 2)
INPUT 3 (S-VIDEO)
I
I
I
I
I
V E D _
V E D _
V E D _
V E D _
V E D _
INPUT 4 (VIDEO)
DIGITAL INPUT MODE
Note
• If an underbar (_) appears in the parameter column, enter a space.
-65
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Compatibility Chart
Horizontal Frequency: 15–70 kHz
Vertical Frequency: 43–75 Hz
Pixel Clock: 12–80 MHz
Compatible with sync on green
XGA compatible in intelligent compression
PC/
MAC/
WS
Horizontal
Vertical
VESA
Standard
DVI
Support
Frequency Frequency
Resolution
Display
(kHz)
27.0
(Hz)
60
640
ן 350 31.5
27.0
70
60
720
ן 350 31.5
27.0
31.5
27.0
31.5
26.2
31.5
34.7
37.9
37.5
70
60
70
60
70
50
60
70
72
75
50
56
60
70
72
75
43
50
70
72
60
640
ן 400 Upscale
VGA
720
ן 400 ✔
✔
✔
✔
✔
640
ן 480 ✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
PC
31.4
35.1
37.9
44.5
48.1
46.9
35.5
40.3
56.5
58.1
45.0
✔
✔
SVGA
800
ן 600 ✔
✔
✔
Intelligent
Compression
XGA 1,024
ן 768 ✔
—
1,280
ן 720 PC/
MAC 13"
Upscale
34.9
67
VGA
640
ן 480 46.8
49.6
48.4
60.0
75
75
60
75
MAC 16" SVGA 832
ן 624 Intelligent
Compression
✔
✔
PC/
XGA
1,024
ן 768 MAC 19"
Note
• This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD)
mode. Should this occur, turn off the LCD display on the notebook computer and output the display data in
“CRT only” mode. Details on how to change display modes can be found in your notebook computer’s opera-
tion manual.
-66
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Product type Projector
Model XV-Z200E
Video system PAL/PAL 60/PAL-M/PAL-N/SECAM/NTSC 3.58/NTSC 4.43
DTV 480I/480P/720P/1080I
Display method DLP chip, RGB optical shutter method
DLP panel Panel size: 0.6Љ
Display method: Single Panel Digital Micromirror Device (DMD™) by Texas Instruments
Drive method: Digital Light Processing (DLP™)
No. of dots: 589,824 dots (1,024 [H]
ן 576 [V]) Lens 1–1.2
ן zoom lens, F1.75–2.04 f=28.0–33.5 mm Projection lamp 210 W/168 W SHP lamp
Video input signal RCA Connector: VIDEO (INPUT 4), composite video, 1.0 Vp-p, sync negative, 75 Ω
terminated
S-video input signal 4-pin Mini DIN connector (INPUT 3)
Y (luminance signal): 1.0 Vp-p, sync negative, 75 Ω terminated
C (chrominance signal): Burst 0.286 Vp-p, 75 Ω terminated
Component input signal RCA Connector
(INPUT 1) Y: 1.0 Vp-p, sync negative, 75 Ω terminated
PB: 0.7 Vp-p, 75 Ω terminated
PR: 0.7 Vp-p, 75 Ω terminated
Component input signal 29-pin connector
(INPUT 2) DVI input signal: Digital 250–1,000 mV 50 Ω
Analog 0.7 Vp-p 75 Ω
Y: 1.0 Vp-p, sync negative, 75 Ω terminated
PB: 0.7 Vp-p, 75 Ω terminated
PR: 0.7 Vp-p, 75 Ω terminated
Horizontal resolution 520 TV lines (NTSC 3.58 input)
RGB input signal DVI-I terminal
<Digital>
Input impedance 50 Ω
Input level 250-1000 mV
<Analog>
Input impedance 75 Ω
Input level 0.7 Vp-p
<Synchronization signal>
• Separate sync/Composite sync
Input level TTL level
Input impedance 1 KΩ
• Green on sync
Input level (Synchronizing input) 0.286 Vp-p
Input impedance 75 Ω
Pixel clock 12–80 MHz
Vertical frequency 43–75 Hz
Horizontal frequency 15–70 kHz
Computer control signal 9-pin D-sub connector (RS-232C Port)
Rated voltage AC 100–240 V
Input current 3.2 A
Rated frequency 50/60 Hz
Power consumption 285 W
Heat dissipation 1,070 BTU/hour
Operating temperature
ם 5°C to ם 35°C Storage temperature
מ 20°C to ם 60°C Cabinet Plastic
I/R carrier frequency 38 kHz
Dimensions (approx.) 368 (W)
ן 153.8 (H) ן 327 (D) mm (including swivel stand) 368 (W)
ן 118 (H) ן 327 (D) mm (main body only) Weight (approx.) 4.6 kg (including swivel stand)
4.1 kg (main body only)
Supplied accessories Remote control, Two AA size batteries, Power cord, 21 pin RCA conversion adaptor,
Video cable, Terminal cover, Screws for terminal cover, Lens cap (attached on the
body), Operation manual
Replacement parts Lamp unit (Lamp/cage module) (BQC-XVZ200++1), Remote control
(RRMCGA218WJSA), AA size batteries, Power cord for Europe except U.K.
(QACCV4002CEZZ), Power cord for U.K., Hong Kong and Singapore
(QACCBA012WJPZ), Power cord for Australia and New Zealand (QACCLA018WJPZ),
21 pin RCA conversion adaptor (QSOCZ0361CEZZ), Video cable (QCNWGA001WJZZ),
Terminal cover (GCOVAA116WJKB), Screws for terminal cover (XBBSN40P10000), Lens
cap (CCAPHA004WJ01), Operation manuals; for European 7 languages (TINS-
B007WJZZ) / for Chinese, Korean and Arabic (TINS-B008WJZZ)
This SHARP projector uses a DMD chip. This very sophisticated chip contains 589,824 pixels. As with any high
technology electronic equipment such as large screen TVs, video systems and video cameras, there are certain
acceptable tolerances that the equipment must conform to.
Specifications are subject to change without notice.
-67
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
Units: mm
Rear View
Side View
Top View
Side View
Front View
368
Bottom View
-68
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
Aspect Ratio
Gamma
Width and height ratio of an image. The normal
aspect ratio of a computer and video image is 4:3.
There are also wide images with an aspect ratio
of 16:9 and 21:9.
Image quality enhancement function that offers a
richer image by brightening the darker portions of
the image without altering the brightness of the
brighter portions. You can select from four differ-
ent modes: Standard, Cinema 1, Cinema 2 and
Cinema 3.
Auto Sync
Optimizes projected computer images by auto-
matically adjusting certain characteristics.
Intelligent compression and expansion
High quality resizing of lower and higher resolu-
tion images to fit the projector’s native resolution.
Background
Initial setting image projected when no signal is
being output.
Phase
Phase shift is a timing shift between isomorphic
signals with the same resolution. When phase level
is incorrect, the projected image typically displays
horizontal flicker.
Clock
Clock adjustment is used to adjust vertical noise
when clock level is incorrect.
CLR Temp (Colour temperature)
Resize
Function that can be used to adjust the colour tem-
perature to suit the type of image input to the pro-
jector. Decrease the colour temperature to create
warmer, reddish images for natural flesh tones,
or increase to create cooler, bluish images for a
brighter picture.
Allows you to modify or customize the picture dis-
play mode to enhance the input image. You can
select from four different modes: SIDE BAR,
SMART STRETCH, CINEMA ZOOM and
STRETCH.
RS-232C
Composite sync
Function to control the projector from the com-
puter by using the RS-232C ports on the projec-
tor and computer.
Signal combining horizontal and vertical sync
pulses.
Digital keystone correction
Stretch
Function to digitally correct a distorted image when
the projector is set up at an angle, smoothes out
jaggies on keystone images and compresses the
image not only horizontally but vertically keeping
the 16 : 9 aspect ratio.
Mode that stretches the 4:3 image horizontally to
display it on the wide screen.
Sync on green
Video signal mode of a computer which overlaps
horizontal and vertical sync signal to green colour
signal pin.
DVI (Digital Visual Interface)
Display digital interface that also supports analog
interfaces.
-69
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
A
R
AC socket............................................................. 14
Adjusting the Picture ............................................ 44
ADJUSTMENT buttons ........................................ 39
Aspect ratio .......................................................... 35
Automatic power shut-off function ........................ 54
Auto sync adjustment........................................... 50
AUTO SYNC button ............................................. 50
Rear projection..................................................... 28
Remote control..................................................... 10
Remote control sensor ......................................... 11
Remote control signal transmitter ........................ 10
RESIZE button ..................................................... 35
RS-232C terminal ................................................ 23
S
B
STANDBY button ................................................. 32
STRETCH ............................................................ 36
S-VIDEO INPUT terminal ..................................... 15
Sync on green ...................................................... 66
Background .......................................................... 53
C
Ceiling-mount ....................................................... 28
Ceiling+Rear ........................................................ 56
Clock .................................................................... 48
COMPONENT terminals ...................................... 17
T
TEMPERATURE WARNING indicator ................. 58
U
D
UNDO button........................................................ 39
DIGITAL INPUT terminal ...................................... 20
DVI ....................................................................... 20
V
VIDEO INPUT terminal ........................................ 16
Video System ....................................................... 52
E
Eco mode ............................................................. 53
ENTER button ...................................................... 39
Exhaust ventilative hole ......................................... 6
Z
Zoom knob ........................................................... 25
F
Focus ring ............................................................ 25
FREEZE button .................................................... 35
I
INPUT buttons...................................................... 31
K
Kensington Lock .................................................. 63
KEYSTONE button............................................... 33
L
LAMP indicator ..................................................... 58
Lens shift .............................................................. 25
M
MENU button........................................................ 38
O
ON button............................................................. 30
On-screen display ................................................ 51
On-screen display language ................................ 31
P
Phase ................................................................... 48
Power cord ........................................................... 14
POWER indicator ................................................. 30
-70
Download from Www.Somanuals.com. All Manuals Search And Download.
SHARP CORPORATION
Printed on 100% post-consumer recycled paper.
Gedruckt auf 100% wiederverwertungs Papier.
Imprimé sur 100% de papier recyclé.
Utskrift på återvunnet papper av 100% återvunnet material.
Impreso en 100% de papel reciclado de postconsumo.
Stampato su carta riciclata al 100%.
Printed in Japan
In Japan gedruckt
Imprimé au Japon
Triykt i Japan
Impreso en Japón
Stampato in Giappone
Gedrukt in Japan
TINS-B007WJZZ
03P11-JWM
Gedrukt op 100% kringlooppapier.
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Sharp All in One Printer MX M1100 User Manual
Sharp Stereo System CD G20000 User Manual
Sharp Stereo System XL DAB102DH User Manual
Sony Car Stereo System XR CA430X User Manual
Sony Graphics Tablet SGP561 User Manual
Sony Network Card PCWA C500 User Manual
Sony Security Camera Smarter Security User Manual
Sprint Nextel Cell Phone PM 225 User Manual
Sunbeam Hot Beverage Maker KE6400 User Manual
Sunbeam Hot Beverage Maker KE7500S User Manual