DATA PROJECTOR
MODEL
XG-C455W
PG-C355W
OPERATION MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using the projector, please read this operation manual carefully.
Introduction
ENGLISH
There are two important reasons for prompt warranty registration of your new SHARP Projector, using
the REGISTRATION CARD packed with the projector.
1. WARRANTY
This is to assure that you immediately receive the full benefit of the parts, service and labor
warranty applicable to your purchase.
2. CONSUMER PRODUCT SAFETY ACT
To ensure that you will promptly receive any safety notification of inspection, modification, or
recall that SHARP may be required to give under the 1972 Consumer Product Safety Act, PLEASE
READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE.
U.S.A. ONLY
WARNING: High brightness light source. Do not stare into the beam of light, or view directly. Be especially
careful that children do not stare directly into the beam of light.
WARNING: To reduce the risk of fire or electric shock, do not expose this product to
rain or moisture.
See bottom of projector.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT REMOVE SCREWS
EXCEPT SPECIFIED USER
to constitute a risk or electric shock to
SERVICE SCREW.
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
persons.
CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The exclamation point within a triangle is
intended to alert the user to the presence of
important operating and maintenance
(servicing) instructions in the literature
accompanying the product.
WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not
expressly approved by the manufacturer could void the user’s authority to operate this equip-
ment.
U.S.A. ONLY
INFORMATION
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the operation manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference, in which case
the user will be required to correct the interference at his own expense.
U.S.A. ONLY
The enclosed computer cable must be used with the device. The cable is provided to ensure that the device
complies with FCC Class A verification.
U.S.A. ONLY
WARNING:
This is a Class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
-1
Download from Www.Somanuals.com. All Manuals Search And Download.
PRODUCT DISPOSAL
This product utilizes tin-lead solder, and lamp containing a small amount of mercury.
Disposal of these materials may be regulated due to environmental considerations. For
disposal or recycling information, please contact your local authorities, the Electronics
or Sharp at 1-800-BE-SHARP.
U.S.A. ONLY
Caution Concerning Lamp Replacement
See “Replacing the Lamp” on page 61.
This SHARP projector uses an LCD (Liquid Crystal Display) panel. This very sophisticated panel contains 1,024,000
pixels (x RGB) TFT’s (Thin Film Transistors). As with any high technology electronic equipment such as large
screen TVs, video systems and video cameras, there are certain acceptable tolerances that the equipment must
conform to.
This unit has some inactive pixels within acceptable tolerances which may result in inactive dots on the picture
screen. This will not affect the picture quality or the life expectancy of the unit.
• Microsoft® and Windows® are registered trademarks of Microsoft Corporation in the United States and/or
other countries.
• PC/AT is a registered trademark of International Business Machines Corporation in the United States.
• Adobe® Reader® is a trademark of Adobe Systems Incorporated.
• Macintosh® is a registered trademark of Apple Computer, Inc. in the United States and/or other countries.
• PJLink is a registered trademark or an application trademark in Japan, the United States and/or other
countries/regions.
• All other company or product names are trademarks or registered trademarks of their respective compa-
nies.
Authorized representative responsible for the European Union Community Market
SHARP ELECTRONICS (Europe) GmbH
E.U. ONLY
Sonninstraße 3, D-20097 Hamburg
-2
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Read this Operation Manual
• In this operation manual, the illustrations and on-screen displays are simplified for explana-
tion.This may differ from the actual on-screen display.
Using the Menu Screen
Adjustment
buttons ('/"/\/|)
MOUSE/Adjustment
buttons ('/"/\/|)
ENTER button
ENTER
button
MENU button
Buttons used in this
operation
MENU button
Buttons used in this
operation
RETURN button
RETURN button
• Press RETURN to
return to previous
screen when the
menu is displayed
Menu Selections (Adjustments)
Example: Adjusting “Bright”.
• This operation can also be performed by using the buttons on the projector.
Example: “Picture” screen menu
Menu item
1
2
Press MENU.
Button used in
this step
• The “Picture” menu screen for the se-
lected input mode is displayed.
Picture
SIG
SCR
PRJ
Net.
Picture Mode
Contrast
Bright
Standard
0
0
0
0
0
0
0
Press | or \ and select “Pic-
ture” to adjust.
Color
Tint
Sharp
Red
Blue
CLR Temp
Progressive
Film Mode
DNR
7500K
3D Progressive
On-screen display
Auto
Off
Off
MNR
Off
Eco+Quiet Mode
Reset
SEL./ADJ.
RETURN
ENTER
END
-43
Info
...........Indicates safeguards when using the projector.
........Indicates additional information for setting up and operating the projector.
Note
For Future Reference
Maintenance
Troubleshooting
Index
Page 56
Pages 66 and 67
Page 70
-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Preparing
Introduction
Useful Features
How to Read this Operation Manual............. 3
Contents.......................................................... 4
Menu Items ................................................... 40
Using the Menu Screen ............................... 43
Menu Selections (Adjustments) ......................... 43
Picture Adjustment (“Picture” menu) ........ 45
Selecting the Picture Mode ............................... 45
Adjusting the Image .......................................... 45
Adjusting the Color Temperature ....................... 45
Selecting the Progressive Mode........................ 46
Selecting the Film Mode .................................... 46
Reducing Image Noise (DNR)........................... 46
Mosquito Noise Reduction (MNR) ..................... 46
Eco+Quiet Mode Setting ................................... 46
Signal Adjustment (“SIG-ADJ” Menu) ........ 47
Adjusting the Computer Image ......................... 47
Resolution Setting.............................................. 47
Auto Sync Adjustment ....................................... 47
Signal Type Setting ............................................ 47
Selecting the Dynamic Range ........................... 48
Setting the Video System................................... 48
Checking the Input Signal ................................. 48
Screen Adjustment (“SCR-ADJ” Menu) ..... 49
Setting the Resize Mode ................................... 49
Adjusting the Image Position............................. 49
Keystone Correction .......................................... 49
Setting the On-screen Display........................... 50
Selecting a Startup and Background Image ..... 50
Selecting the Menu Screen Position .................. 50
Reversing/Inverting Projected Images .............. 50
Selecting the On-screen Display Language ..... 50
Helpful Functions Set during Installation
(“PRJ-ADJ” menu) ................................. 51
Auto Power Off Function .................................... 51
Auto Restart Function ........................................ 51
Setting the Confirmation Sound
How to Access the PDF Operation Manuals....
6
IMPORTANT SAFEGUARDS .......................... 7
Accessories .................................................. 10
Part Names and Functions.......................... 12
Using the Remote Control........................... 15
Usable Range .................................................... 15
Inserting the Batteries ....................................... 15
Quick Start
Quick Start .................................................... 16
Setup
Setting Up the Projector .............................. 18
Setting Up the Projector .................................... 18
Projection (PRJ) Mode ....................................... 19
Connections
Samples of Cables for Connection............. 21
Connecting to a Computer .......................... 23
Connecting to Video Equipment................. 25
Controlling the Projector by a Computer... 27
Connecting to a Monitor with RGB
Input Terminal ......................................... 28
Connecting to an Amplifier or Other
Audio Equipment.................................... 29
Using
(System Sound) ........................................... 51
Speaker Setting ................................................. 51
Audio Output Type Setting ................................ 51
Monitor Output................................................... 51
LAN/RS232C ..................................................... 51
Selecting the Transmission Speed (RS-232C) .. 52
Fan Mode Setting .............................................. 52
System Lock Function ....................................... 52
Keylock Function ............................................... 53
Returning to the Default Settings....................... 53
Checking the Lamp Life Status ......................... 53
Setting up the Projector Network
Basic Operation
Turning the Projector On/Off....................... 30
Connecting the Power Cord .............................. 30
Turning the Projector On.................................... 30
Turning the Power Off (Putting the Projector into
Standby Mode)............................................ 30
Image Projection .......................................... 31
Using the Adjustment Feet ................................ 31
Correcting Trapezoidal Distortion ...................... 32
Adjusting the Lens............................................. 33
Switching the Input Mode .................................. 34
Adjusting the Volume ......................................... 34
Displaying the Black Screen and Turning off
Environment (“Network” menu)............ 54
Setting a Password ............................................ 54
DHCP Client Setting .......................................... 55
TCP/IP Setting ................................................... 55
Confirming the Projector Information................. 55
the Sound Temporarily ................................ 34
Displaying and Setting the Break Timer ............ 35
Switching the Eco+Quiet Mode ......................... 35
Auto Sync (Auto Sync Adjustment) ................... 35
Freezing a Moving Image .................................. 35
Selecting the Picture Mode ............................... 36
Displaying an Enlarged Portion of an Image.... 36
Resize Mode ...................................................... 37
Using the Remote Control as the Wireless
Computer Mouse ........................................ 39
-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference
Appendix
Maintenance ................................................. 56
Replacing the Air Filter ................................ 57
Replacing the Air Filter ...................................... 57
Maintenance Indicators ............................... 59
Regarding the Lamp .................................... 61
Lamp ................................................................. 61
Caution Concerning the Lamp .......................... 61
Replacing the Lamp .......................................... 61
Removing and Installing the Lamp Unit ............ 62
Resetting the Lamp Timer ................................. 63
Storing the Projector ................................... 64
How to Use the Storage Case ........................... 64
Computer Compatibility Chart .................... 65
Troubleshooting ........................................... 66
For SHARP Assistance ................................ 68
Specifications ............................................... 69
Index .............................................................. 70
SETUP MANUAL
Refer to the “SETUP MANUAL”
contained on the supplied CD-
ROM for details.
Setting up the Screen .................................... 2
Screen Size and Projection Distance ........... 3
Changing the Lens......................................... 9
Connecting Pin Assignments ..................... 11
RS-232C Specifications and Commands ... 13
Setting up the Projector Network
Environment............................................ 18
Controlling the Projector via LAN .............. 24
Setting up the Projector Using
RS-232C or Telnet ................................... 29
Resetting the Lamp Timer
of the Projector via LAN......................... 39
Troubleshooting ........................................... 41
Dimensions................................................... 44
-5
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Access the PDF Operation Manuals
PDF operation manuals in several languages are included in the CD-ROM, so that you can
work with the projector.To utilize these manuals, you need to install Adobe® Reader® on your
computer (Windows® or Macintosh®).
Please download Adobe® Reader® from the Internet (http://www.adobe.com).
Accessing the PDF Manuals
For Windows®:
For Macintosh®:
1 Insert the CD-ROM in the CD-ROM drive.
2 Double click the “My Computer” icon.
3 Double click the “CD-ROM” drive.
1 Insert the CD-ROM in the CD-ROM drive.
2 Double click the “CD-ROM” icon.
3
When you want to view the operation manual
1) Double click the “MANUALS” folder.
2) Double click the language (name of the
folder) that you want to view.
4
When you want to view the operation manual
1) Double click the “MANUALS” folder.
2) Double click the language (name of the
folder) that you want to view.
3) Double click the pdf file to access the pro-
jector manuals.
When you want to view the setup manual
1) Double click the “SETUP” folder.
2) Double click the language (name of the
folder) that you want to view.
3) Double click the pdf file to access the pro-
jector manuals.
When you want to view the setup manual
1) Double click the “SETUP” folder.
2) Double click the language (name of the
folder) that you want to view.
3) Double click the pdf file to access the setup
manual.
3) Double click the pdf file to access the setup
manual.
Info
• If the desired pdf file cannot be opened by double clicking the mouse, start Adobe® Reader® first, then
specify the desired file using the “File”, “Open” menu.
-6
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFEGUARDS
CAUTION: Please read all of these instructions before you operate this product and save these
instructions for later use.
Electrical energy can perform many useful functions. This product has been engineered and manufactured to
assure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR
FIRE HAZARDS. In order not to defeat the safeguards incorporated in this product, observe the following basic
rules for its installation, use and servicing.
1. Read Instructions
13. Power-Cord Protection
All the safety and operating instructions should be read before
the product is operated.
Power-supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plugs,
convenience receptacles, and the point where they exit from
the product.
2. Retain Instructions
The safety and operating instructions should be retained for
future reference.
14. Lightning
3. Heed Warnings
For added protection for this product during a lightning storm,
or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet and disconnect the cable
system. This will prevent damage to the product due to
lightning and power-line surges.
All warnings on the product and in the operating instructions
should be adhered to.
4. Follow Instructions
All operating and use instructions should be followed.
5. Cleaning
15. Overloading
Unplug this product from the wall outlet before cleaning. Do
not use liquid cleaners or aerosol cleaners. Use a damp cloth
for cleaning.
Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or
electric shock.
6. Attachments
16. Object and Liquid Entry
Do not use attachments not recommended by the product
manufacturer as they may cause hazards.
Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
7. Water and Moisture
Do not use this product near water–for example, near a bath
tub, wash bowl, kitchen sink, or laundry tub; in a wet
basement; or near a swimming pool; and the like.
17. Servicing
Do not attempt to service this product yourself as opening or
removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service
personnel.
8. Accessories
Do not place this product on an unstable cart, stand, tripod,
bracket, or table. The product may fall, causing serious injury
to a child or adult, and serious damage to the product. Use
only with a cart, stand, tripod, bracket, or table recommended
by the manufacturer, or sold with the product. Any mounting
of the product should follow the manufacturer’s instructions,
and should use a mounting accessory recommended by the
manufacturer.
18. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing
to qualified service personnel under the following conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into
the product.
9. Transportation
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operating instructions, as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to normal
operation.
A product and cart combination should
be moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the product and cart
combination to overturn.
10. Ventilation
Slots and openings in the cabinet are provided for ventilation
to ensure reliable operation of the product and to protect it
from overheating, and these openings must not be blocked
or covered. The openings should never be blocked by placing
the product on a bed, sofa, rug, or other similar surface. This
product should not be placed in a built-in installation such as
a bookcase or rack unless proper ventilation is provided or
the manufacturer’s instructions have been adhered to.
e. If the product has been dropped or damaged in any
way.
f. When the product exhibits a distinct change in
performance, this indicates a need for service.
19. Replacement Parts
When replacement parts are required, ensure that the service
technician has used replacement parts specified by the
manufacturer or have the same characteristics as the original
part. Unauthorized substitutions may result in fire, electric
shock, or other hazards.
11. Power Sources
This product should be operated only from the type of power
source indicated on the marking label. If you are not sure of
the type of power supply to your home, consult your product
dealer or local power company. For products intended to
operate from battery power, or other sources, refer to the
operating instructions.
20. Safety Check
Upon completion of any service or repairs to this product,
ask the service technician to perform safety checks to
determine that the product is in proper operating condition.
12. Grounding or Polarization
This product is provided with one of the following types of
plugs. If the plug should fail to fit into the power outlet,
please contact your electrician.
21
.
Wall or Ceiling Mounting
This product should be mounted to a wall or ceiling only as
recommended by the manufacturer.
22. Heat
Do not defeat the safety purpose of the plug.
a. Two-wire type (mains) plug.
This product should be situated away from heat sources such
as radiators, heat registers, stoves, or other products
(including amplifiers) that produce heat.
b. Three-wire grounding type (mains) plug with a
grounding terminal.
This plug will only fit into a grounding type power
outlet.
-7
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFEGUARDS
Ensure that you read the following safeguards when
setting up your projector.
Caution concerning the lamp unit
Warning about placing the projector in a
■ Potential hazard of glass par-
high position
ticles if lamp ruptures. In case
of lamp rupture, contact your
nearest Sharp Authorized Pro-
jector Dealer or Service Cen-
ter for replacement.
■ When placing the projector in a high posi-
tion, make certain it is carefully secured to
avoid personal injury caused by the projec-
tor falling down.
See “Regarding the Lamp” on
page 61.
CAUTION
PRECAUCIÓN
PRÉCAUTION
Do not subject the projector to hard im-
pact and/or vibration.
■ Take care with the lens so as not to hit or
damage the surface of the lens.
Caution concerning the setup of the pro-
jector
■ For minimal servicing and to maintain high
image quality, SHARP recommends that this
projector be installed in an area free from hu-
midity, dust and cigarette smoke. When the
projector is subjected to these environments,
the vents and lens must be cleaned more
often. As long as the projector is regularly
cleaned, use in these environments will not
reduce the overall operation life of the unit.
Internal cleaning should only be performed
by a Sharp Authorized Projector Dealer or
Service Center.
Rest your eyes occasionally.
■ Continuously watching the screen for long
hours will cause eye strain. Take regular
breaks to rest your eyes.
Avoid locations with extremes of tem-
perature.
■ The operating temperature of the projector
is from 41°F to 95°F (+5°C to +35°C).
■ The storage temperature of the projector is
from –4°F to 140°F (–20°C to +60°C).
Do not set up the projector in places ex-
posed to direct sunlight or bright light.
■ Position the screen so that it is not in direct
sunlight or room light. Light falling directly on
the screen washes out the colors, making
viewing difficult. Close the curtains and dim
the lights when setting up the screen in a
sunny or bright room.
Do not block the intake and exhaust
vents.
■ Allow at least 7 7/8 inches (20 cm) of space
between the exhaust vent and the nearest
wall or obstruction.
■ Ensure that the intake vent and the exhaust
vent are not obstructed.
The projector may be safely tilted to a
maximum angle of 9 degrees.
■ Placement should be within 9 degrees of
horizontal.
■ If the cooling fan becomes obstructed, a pro-
tection circuit will automatically put the pro-
jector into standby mode to prevent overheat
damage. This does not indicate a malfunc-
tion (see pages 59 and 60). Remove the pro-
jector power cord from the wall outlet and wait
at least 10 minutes. Place the projector where
the intake and exhaust vents are not blocked,
plug the power cord back in and turn on the
projector. This will return the projector to the
normal operating condition.
When using the projector in high-altitude
areas such as mountains (at altitudes of
approximately 1,500 meters (4,900 feet)
or more)
■ When you use the projector in high-altitude
areas with thin air, set “Fan Mode” to “High”.
Neglecting this can affect the longevity of the
optical system.
-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Caution regarding usage of the projector
■ When using the projector, take care not to sub-
ject it to hard impact and/or vibration, as this
can result in damage. Take extra care with the
lens. If you are not to use the projector for a
long time, make certain you unplug the power
cord from the wall outlet, and disconnect any
other cables connected to it.
Info
• The cooling fan regulates the internal tem-
perature, and its performance is automati-
cally controlled.The sound of the fan may
change during projector operation due to
changes in the fan speed. This does not
indicate malfunction.
■ Do not carry the projector by holding the lens.
■
When storing the projector, ensure you attach
the lens cap to the projector. (See page 12.)
■ Do not expose the storage case or projector
to direct sunlight or near heat sources. The
storage case or projector may change color
or become deformed.
Other connected equipment
■ When connecting a computer or other audio-
visual equipment to the projector, make the
connections AFTER unplugging the power
cord of the projector from the AC outlet and
turning off the equipment to be connected.
■ Please read the operation manuals of the pro-
jector and the equipment to be connected for
instructions on how to make the connections.
Using the projector in other countries
■ The power supply voltage and the shape of
the plug may vary depending on the region
or country you are using the projector in.
When using the projector overseas, make
sure you use an appropriate power cord for
the country you are in.
Temperature monitor function
■
If the projector starts to over-
heat due to setup problems
or blockage of the air vents,
“
” and “
” will illumi-
nate in the lower left corner of the picture. If the
temperature continues to rise, the lamp will turn
off, the temperature warning indicator on the
projector will blink, and after a 90-second cool-
ing-off period the projector will enter the standby
mode. Refer to “Maintenance Indicators” on
page 59 for details.
-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
Supplied accessories
Two R-6 batteries
(“AA” size, UM/SUM-3,
HP-7 or similar)
RGB cable
(10' (3.0 m))
<QCNWGA045WJPZ>
DIN-D-sub RS-232C
adaptor
(5 57/64" (15 cm))
<QCNWGA091WJPZ>
Remote control
<RRMCGA623WJSA>
Power cord*
(1)
(4)
(2)
(3)
For U.S., Canada, etc. For Europe, except U.K.
For U.K., Hong Kong For Australia, New
(6' (1.8 m))
<QACCDA007WJPZ>
(6' (1.8 m))
<QACCVA011WJPZ>
and Singapore
(6' (1.8 m))
Zealand and Oceania
(6' (1.8 m))
<QACCBA036WJPZ> <QACCLA018WJPZ>
*Use the power cord that corresponds to the wall outlet in your country.
Storage case
<GCASNA020WJSA>
Lens cap (attached)
<PCAPHA026WJSA>
Lens cap strap
<UBNDTA017WJZZ>
• Operation manual (this manual <TINS-D563WJZZ> and CD-ROM <UDSKAA102WJZZ>)
Note
• Codes in “< >” are Replacement parts codes.
Optional accessories
■ Lamp unit
AN-C430LP
■ Ceiling-mount adaptor
AN-60KT
AN-XGCM55 (for U.S.A. only)
AN-JT200 (for U.S.A. only)
AN-TK201 <for AN-60KT>
AN-TK202 <for AN-60KT>
AN-EP101B <for AN-XGCM55 and AN-JT200>
(for U.S.A. only)
■ Universal bracket
■ Ceiling-mount unit
■ Remote receiver
AN-MR2
■ 3 RCA to 15-pin D-sub cable (10' (3.0 m))
AN-C3CP2
Note
• Some of the optional accessories may not be available depending on the region. Please check with your
nearest Sharp Authorized Projector Dealer or Service Center.
-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional lenses
■ Lens
Projection distance for 100" screen size
10' 5" – 13' 1" (3.2 m – 4.0 m)
Wide-zoom lens (× 1.5 – 1.9)
AN-C12MZ
AN-C18MZ
AN-C27MZ
AN-C41MZ
Tele-zoom lens (× 2.2 – 2.8)
Tele-zoom lens (× 3.3 – 5.1)
Tele-zoom lens (× 5.1 – 7.2)
15' 7" – 19' 10" (4.8 m – 6.0 m)
23' 2" – 35' 8" (7.1 m – 10.9 m)
36' 2" – 50' 10" (11.0 m – 15.5 m)
The standard zoom lens is attached to the projector.
The optional lenses from Sharp are also available for specialized application. Please see
your nearest Sharp Authorized Projector Dealer for details on all the lenses. (Refer to the
SETUP MANUAL on the supplied CD-ROM for details.) Also, be sure to have service person-
nel install the optional lenses.
Throw Distance
The graph below is for 100 inches (254 cm) screen with 16:10 Signal Input (Normal Mode).
Screen
Wide-zoom lens (AN-C12MZ)
10'5"–13'1" (3.2 m–4.0 m)
Throw distance ratio 1:1.5–1.9
Standard zoom lens
12'4"–14'9" (3.8 m–4.5 m)
Throw distance ratio 1:1.8–2.1
Tele-zoom lens (AN-C18MZ)
15'7"–19'10" (4.8 m–6.0 m)
Throw distance ratio 1:2.2–2.8
Tele-zoom lens (AN-C27MZ)
23'2"–35'8" (7.1 m–10.9 m)
Throw distance ratio 1:3.3–5.1
Tele-zoom lens (AN-C41MZ)
36'2"–50'10" (11.0 m–15.5 m)
Throw distance ratio 1:5.1–7.2
10
20
30
40
50
55(ft)
-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
Numbers in
refer to the main pages in this operation manual where the topic is explained.
Projector
Top View
Power indicator
30·59
30·59 Lamp indicator
STANDBY/ON button 30
For turning the power on and
putting the projector into
standby mode.
59
Temperature warning
indicator
35 AUTO SYNC button
For automatically adjusting
images when connected to
a computer.
KEYSTONE button 32
For entering the Keystone
Correction mode.
Adjustment buttons 43
('/"/\/|)
ENTER button
For setting items selected
or adjusted on the menu.
44
For selecting and adjusting
on-screen items.
34 Volume buttons
For adjusting the speaker
sound level.
RETURN button
For returning to the previous
display.
43
43 MENU button
For displaying adjustment
and setting screens.
INPUT buttons
For switching input mode.
34
35 ECO+QUIET button
For lowering the noise of the
cooling fan and extending the
lamp life.
Front View
Zoom knob 33
For enlarging/
reducing the picture.
33
Focus ring
For adjusting the focus.
51 Speaker
31
31
Tilt dial
15 Remote control
sensor
Height Adjustment
button
31
Height Adjustment
button
31
Adjustment foot
31 Adjustment foot
Air filter/Intake vent
(on the bottom of the projector)
56·57
Push both sides of the lens cap to
attach or remove.
Attaching the lens cap
After putting the lens cap strap on the lens
cap, pass the other end of the strap
through the hole on the front side of the
projector, next to the lens, as shown in
the illustration.
-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector (Rear View)
Terminals
COMPUTER/COMPONENT 2 input terminal 23
·25
25 AUDIO input terminal
Terminal for Computer RGB and Component signals.
Shared audio input terminal for COMPUTER/COMPONENT 2 and
DVI-D.
AUDIO input terminal
24·25
DVI-D input terminal
23
·
25
Audio input terminal for
Terminal for DVI Digital RGB and Digital Component
signals.
COMPUTER/COMPONENT 1.
28
LAN terminal
Terminal for controlling the
projector using a computer
via network.
23·25
COMPUTER/COMPONENT 1
input terminal
Terminal for Computer RGB
and Component signals.
14 WIRED REMOTE terminal
For connecting the remote control
to the projector when the signals
from the remote control cannot
reach the remote control sensor.
S-VIDEO input terminal 26
VIDEO input terminal 26
27 RS-232C terminal
Terminal for controlling the
projector using a computer.
26
AUDIO input terminal
for S-video
39
USB terminal
Terminal connecting with the USB terminal on the
computer for using the supplied remote control as the
computer mouse.
AUDIO input terminal 26
for Video
29 AUDIO output terminal
MONITOR output terminal
Output terminal for Computer RGB and
Component signals.
28
Shared for COMPUTER/COMPONENT 1 and 2.
15 Remote control
sensor
Exhaust vent
56
Carrying handle
Intake vent 56
AC socket
Connect the supplied power cord.
30
* Kensington Security
Standard connector
Using the Carrying Handle
When transporting the projector, carry it by the carrying handle on the side.
• Always put on the lens cap to prevent damage to the lens when transporting the
projector.
• Do not lift or carry the projector by the lens or the lens cap as this may damage
the lens.
* Using the Kensington Lock
• This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security
System. Refer to the information that came with the system for instructions on how to use it to secure the
projector.
-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
Remote Control
STANDBY button
30
WIRED R/C JACK
For controlling the projector by connecting
the remote control to the projector.
For putting the projector into
standby mode.
ON button
30
KEYSTONE button
For entering the Keystone
Correction mode.
32
For turning the power on.
MENU button
For displaying adjustment and
setting screens.
43
ENTER button
For setting items selected or
adjusted on the menu.
44
MOUSE/Adjustment buttons
39·43
('/"/\/|)
• For moving the computer cursor
when with the USB connection
(using a USB cable or the optional
remote receiver).
L-CLICK button
39
For the Left click when with the
USB connection (using a USB
cable or the optional
• For selecting and adjusting on-
screen items.
remote receiver).
MAGNIFY (Enlarge/Reduce)
36
R-CLICK/RETURN button
• For the Right click when with the
USB connection (using a USB
cable or the optional remote receiver).
• For returning to the previous
display.
39·43
buttons
For enlarging/reducing part of the
image.
PAGE Up/Down buttons
39
Same as the [Page Down] and
[Page Up] keys on a computer
keyboard, when with the USB
connection (using a USB cable or
the optional remote receiver).
Volume buttons
For adjusting the speaker sound
level.
34
34
AV MUTE button
For temporarily displaying the black
screen and turning off the sound.
BREAK TIMER button
For displaying the break timer.
35
AUTO SYNC button
For automatically adjusting images
when connected to a computer.
35
FREEZE button
35
37
For freezing images.
RESIZE button
For switching the screen size
(NORMAL, STRETCH, etc.).
PICTURE MODE button
For switching the picture mode.
36
35 ECO+QUIET button
INPUT buttons
For switching to the respective
input modes.
34
For lowering the noise of the cooling
fan and extending the lamp life.
Using the Remote Control with a Signal Cable
When the signals from the remote control cannot be reached due to the positioning of the projector, use a
ø3.5 mm minijack cable to connect the remote control to the projector. Now you can control the projector
with the remote control.
Projector
(Rear view)
Remote control
To WIRED
REMOTE terminal
To WIRED
R/C JACK
ø3.5 mm minijack cable (commercially available or
available as Sharp service part QCNWGA038WJPZ)
Note
• The wireless remote function is not possible when the ø3.5 mm minijack cable is connected to the projector.
Should the wireless remote operation be required, the ø3.5 mm minijack cable should be disconnected
from the projector.
-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Remote Control
Front View
Remote control sensor
Usable Range
The remote control can be used to control
the projector within the ranges shown in the
illustration.
30°
30°
23' (7 m)
30°
Remote control
Note
signal transmitters
• The signal from the remote control can be re-
flected off a screen for easy operation. How-
ever, the effective distance of the signal may
differ depending on the screen material.
Remote control
Rear View
Remote control sensor
30°
When using the remote control:
• Take care not to drop, expose to moisture or
high temperature.
• The remote control may malfunction under a
fluorescent lamp. In this case, move the pro-
jector away from the fluorescent lamp.
30°
Remote control
signal transmitters
30°
23' (7 m)
Remote control
Inserting the Batteries
1
Pull down the tab on the cover and
remove the cover towards the di-
rection of the arrow.
2 Insert the included batteries.
• Insert the batteries making sure the po-
larities correctly match the
and
marks inside the battery compartment.
3 Insert the lower tab of the cover
into the opening, and lower the
cover until it clicks in place.
Incorrect use of the batteries may cause them to leak or explode. Please follow the precautions below.
Caution
• Danger of explosion if battery is incorrectly replaced. Replace only with alkaline or manganese batteries.
• Insert the batteries making sure the polarities correctly match the
and
marks inside the battery compart-
ment.
• Batteries of different types have different properties, therefore do not mix batteries of different types.
• Do not mix new and old batteries.
This may shorten the life of new batteries or may cause old batteries to leak.
• Remove the batteries from the remote control once they have run out, as leaving them in can cause them to leak.
Battery fluid from leaked batteries is harmful to skin, therefore ensure you wipe them first and then remove them
using a cloth.
• The batteries included with this projector may run down in a short period, depending on how they are kept. Be
sure to replace them as soon as possible with new batteries.
• Remove the batteries from the remote control if you will not be using the remote control for a long time.
• Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.
-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start
This section shows the basic operation (projector connecting with the computer). For details, see the page
described below for each step.
Setup and Projection
In this section, connection of the projector and the computer is explained using one example.
7 STANDBY
button
3 7 STANDBY/ON button
6 INPUT buttons
3 ON button
6 ENTER button
5 Zoom knob
5 Focus ring
6 COMPUTER 1
button
4 Tilt dial
4 Height Adjustment buttons
1.Place the projector facing a screen
Page 18
2.Connect the projector to the computer and plug the power
cord into the AC socket of the projector
When connecting equipment other than the computer, see pages 25, 28 and 29.
Pages 23, 30
3.Remove the lens cap and turn the projector on
On the projector
On the remote control
Page 30
-16
Download from Www.Somanuals.com. All Manuals Search And Download.
4.Adjust the angle
•
This projector is equipped with an “Auto V-Keystone
Correction” function that automatically corrects any
trapezoidal distortion within the projected image.
Adjust the projector angle
•
Adjust the projector angle using the Height
Adjustment buttons.
•
Rotate the Tilt dial to adjust the horizontal tilt of
the projector.
Height Adjustment
buttons
Tilt dial
Pages 31, 32
5.Adjust the focus and the zoom
Bring the projected image into focus
Adjust the projected image size
• Bring the projected image into focus by
• Adjust the projected image size by moving the
rotating the focus ring.
zoom knob.
Focus ring
Zoom knob
Page 33
6.Select the INPUT mode
Select the “COMPUTER 1” using the INPUT buttons on the projector or the COMPUTER 1 button on the remote control.
On the
projector
On the remote
control
" INPUT list
" On-screen Display (RGB)
INPUT
COMPUTER1
RGB
COMPUTER1
COMPUTER2
1024 × 768
D
DVI-D Computer
•
When you press the INPUT buttons on the projector, the INPUT list appears.
Press '/" to select an item on the list, and press ENTER to switch to the selected INPUT mode.
• When using the remote control, press COMPUTER1/2, DVI, S-VIDEO or VIDEO to
switch the INPUT mode.
Page 34
7.Turn the Power off
Press the STANDBY button, then press that button again while the confirmation message is displayed, to put the projector into standby mode.
" On-screen Display
On the projector
On the remote control
• Even if you unplug the power cord from the AC outlet, the cooling fan continues to run for a while.
Page 30
-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up the Projector
Setting Up the Projector
For optimal image quality, position the projector perpendicular to the screen with the projector’s feet flat
and level. Doing so will eliminate the need for Keystone correction and provide the best image quality. (See
page 32.)
Standard Setup (Front Projection)
■ Place the projector at the required distance from the screen according
to the desired picture size. (For details, refer to the “SETUP MANUAL” con-
tained on the supplied CD-ROM.)
Example of standard setup
Side View
Base line:
Horizontal line passing through
the lens center
Screen
Lens center
H
L: Projection distance
Ceiling-mount Setup
■ It is recommended that you use the optional Sharp ceil-
ing-mount adaptor and unit for this installation. Before
mounting the projector, contact your nearest Sharp Au-
thorized Projector Dealer or Service Center to obtain the
recommended ceiling-mount adaptor and unit (sold sepa-
rately).
-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Projection (PRJ) Mode
The projector can use any of the 4 projection modes, shown in the diagram below. Select the mode most appro-
priate for the projection setting in use. (You can set the PRJ mode in “SCR-ADJ” menu. See page 50.)
■ Table mounted, front projection
■ Ceiling mounted, front projection
[Menu item ➞ “Front”]
[Menu item ➞ “Ceiling + Front”]
■ Table mounted, rear projection
(with a translucent screen)
[Menu item ➞ “Rear”]
■ Ceiling mounted, rear projection
(with a translucent screen)
[Menu item ➞ “Ceiling + Rear”]
Indication of the Projection Image Size and Projection Distance
For details, refer to the “SETUP MANUAL” contained on the supplied CD-ROM.
Example: 16:10 Signal Input (Normal Mode) for standard lens
Picture Size
500"
424"
×
265"
200"
170"
×
106"
100"
80"
85"
×
53"
42"
68"
×
21"
40"
34"
×
Projection Distance
"
"
"–5'11
"
"
"
"–11'10
3.6 m)
4'11
(1.5 m9–'110.8 m)
(3.0 m
–
14'9
4.5 m)
–73'11
"–
29'7
9.0 m)
–
"
"–
–
12'4
61'7
(18.8 m – 22.5 m)
24'8
(7.5 m
(3.8 m
-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up the Projector
Standard Zoom Lens
F1.7-F1.9, f=28.0-33.6 mm
16:10 Signal Input (Normal Mode)
Picture (Screen) size
Projection distance [L]
Minimum [L1] Maxmum [L2]
Distance from the lens center
to the bottom of the image [H]
Diag. [x]
Width
Height
500'' (1270 cm) 1077 cm (424'') 673 cm (265'') 18.8 m (61' 7") 22.5 m (73' 11")
400'' (1016 cm) 862 cm (339'') 538 cm (212'') 15.0 m (49' 3") 18.0 m (59' 2")
–16 cm (–6 5/16")
–13 cm (–5 3/64")
–10 cm (–3 51/64")
–8 cm (–3 5/32")
–6 cm (–2 17/32")
–5 cm (–1 57/64")
–4 cm (–1 33/64")
–3 cm (–1 17/64")
–3 cm (–1 1/64")
300''
250''
200''
150''
120''
100''
80''
(762 cm) 646 cm (254'') 404 cm (159'') 11.3 m (37' 0") 13.5 m (44' 4")
(635 cm) 538 cm (212'') 337 cm (132'')
(508 cm) 431 cm (170'') 269 cm (106'')
9.4 m (30' 10") 11.3 m (37' 0")
7.5 m (24' 8") 9.0 m (29' 7")
5.6 m (18' 6") 6.8 m (22' 2")
4.5 m (14' 9") 5.4 m (17' 9")
3.8 m (12' 4") 4.5 m (14' 9")
3.0 m (9' 10") 3.6 m (11' 10")
(381 cm) 323 cm (127'') 202 cm
(305 cm) 258 cm (102'') 162 cm
(79'')
(64'')
(53'')
(42'')
(32'')
(21'')
(254 cm) 215 cm
(203 cm) 172 cm
(152 cm) 129 cm
(102 cm) 86 cm
(85'')
(68'')
(51'')
(34'')
135 cm
108 cm
81 cm
60''
2.3 m
(7' 5")
2.7 m (8' 10")
–2 cm
–1 cm
(–49/64")
(–1/2")
40''
54 cm
1.5 m (4' 11") 1.8 m (5' 11")
χ
:
Picture size (diag.) (in/cm)
The formula for picture size and projection distance
L: Projection distance(m/ft)
L1: Minimum projection distance (m/ft)
L2: Maximum projection distance (m/ft)
[m/cm]
χ
χ
L1 (m) = 0.03755
L2 (m) = 0.04507
χ
H: Distance from the lens center to the bottom of the image (cm/in)
H (cm) = –0.03209
[Feet/inches]
χ
χ
L1 (ft) = 0.03755 / 0.3048
L2 (ft) = 0.04507 / 0.3048
χ
H (in) = –0.03209 / 2.54
4:3 Signal Input (Normal Mode)
Picture (Screen) size
Width
Projection distance [L]
Minimum [L1] Maxmum [L2]
Distance from the lens center
to the bottom of the image [H]
Diag. [x]
Height
400'' (1016 cm) 813 cm (320'') 610 cm (240'') 17.0 m (55' 9") 20.4 m (66' 11")
–15 cm (–5 23/32")
–11 cm (–4 19/64")
300''
250''
200''
150''
120''
100''
80''
(762 cm) 610 cm (240'') 457 cm (180'') 12.8 m (41' 10") 15.3 m (50' 3")
(635 cm) 508 cm (200'') 381 cm (150'') 10.6 m (34' 10") 12.8 m (41' 10")
–9 cm
–7 cm
–5 cm
–4 cm
–4 cm
–3 cm
–3 cm
–2 cm
–1 cm
(–3 37/64")
(–2 55/64")
(–2 9/64")
(–1 23/32")
(–1 7/16")
(–1 9/64")
(–1")
(508 cm) 406 cm (160'') 305 cm (120'')
8.5 m (27' 11") 10.2 m (33' 6")
6.4 m (20' 11") 7.7 m (25' 1")
5.1 m (16' 9") 6.1 m (20' 1")
4.3 m (13' 11") 5.1 m (16' 9")
3.4 m (11' 2") 4.1 m (13' 5")
(381 cm) 305 cm (120'') 229 cm
(90'')
(72'')
(60'')
(48'')
(42'')
(36'')
(24'')
(305 cm) 244 cm
(254 cm) 203 cm
(203 cm) 163 cm
(178 cm) 142 cm
(152 cm) 122 cm
(102 cm) 81 cm
(96'')
(80'')
(64'')
(56'')
(48'')
(32'')
183 cm
152 cm
122 cm
107 cm
91 cm
70''
3.0 m
2.6 m
1.7 m
(9' 9")
(8' 4")
(5' 7")
3.6 m (11' 9")
3.1 m (10' 1")
(–55/64")
(–37/64")
60''
40''
61 cm
2.0 m
(6' 8")
χ
:
Picture size (diag.) (in/cm)
The formula for picture size and projection distance
L: Projection distance(m/ft)
L1: Minimum projection distance (m/ft)
L2: Maximum projection distance (m/ft)
[m/cm]
χ
χ
L1 (m) = 0.04251
L2 (m) = 0.05102
χ
H: Distance from the lens center to the bottom of the image (cm/in)
H (cm) = –0.03633
[Feet/inches]
χ
χ
L1 (ft) = 0.04251 / 0.3048
L2 (ft) = 0.05102 / 0.3048
χ
H (in) = –0.03633 / 2.54
Note
• Allow a margin of error in the value in the diagrams above.
• When the distance from the lens center to the bottom of the image [H] is a negative number, this indicates
that the bottom of the image is below the lens center.
• See page 18 about projection distance [L] and distance from the lens center to the bottom of the image [H].
-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Samples of Cables for Connection
•For more details of connection and cables, refer to the operation manual of the connecting equipment.
•You may need other cables or connectors not listed below.
Terminal on
Terminal on the
projector
Equipment
Computer
Cable
connected equipment
RGB cable (supplied)
COMPUTER/
COMPONENT 1, 2
RGB
output
terminal
DVI digital DVI Digital cable (commercially available)
DVI-D
video
output
terminal
ø3.5 mm stereo or mono audio cable (commercially
available or available as Sharp service part
QCNWGA038WJPZ)
AUDIO
(for COMPUTER/
COMPONENT 1, 2, DVI-D)
Audio
output
terminal
Audio-visual
equipment
DVI digital DVI Digital cable (commercially available)
DVI-D
video
output
terminal
Component 3 RCA to 15-pin D-sub cable (optional: AN-C3CP2)
COMPUTER/
video
output
terminal
COMPONENT 1, 2
Terminal Connect with the cable adaptor, etc.
for using
3 RCA to 15-pin
the
D-sub cable
(optional: AN-C3CP2)
dedicated
cable
Cable adaptor (commercially available)
Dedicated cable
S-video cable (commercially available)
Video cable (commercially available)
S-VIDEO
VIDEO
S-video
output
terminal
Video
output
terminal
-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Samples of Cables for Connection
Terminal on
Terminal on the
projector
Equipment
Cable
connected equipment
Audio-visual
equipment
ø3.5 mm stereo minijack to RCA audio cable
(commercially available)
AUDIO
(for COMPUTER/
Audio
output
COMPONENT 1, 2, DVI-D)
terminal
Terminal Connect with the cable adaptor, etc.
for using
Cable adaptor
(commercially available)
the
dedicated
cable
Dedicated cable
ø3.5 mm stereo minijack to RCA audio
cable (commercially available)
RCA audio cable (commercially available)
AUDIO
Audio
output
(for VIDEO, S-VIDEO)
terminal
Terminal Connect with the cable adaptor, etc.
for using
the
dedicated
cable
Cable adaptor
(commercially available)
Dedicated cable
RCA audio cable
(commercially available)
Monitor
RGB cable (supplied or commercially available)
MONITOR OUTPUT
RGB
input
terminal
Amplifier
ø3.5 mm stereo minijack to RCA audio cable
(commercially available)
AUDIO
(MONITOR OUT)
Audio
input
terminal
-22
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to a Computer
Before connecting, ensure the power cord of the projector from the AC outlet is unplugged,
and that the devices to be connected are turned off. After making all connections, turn on the
projector and then the other devices. When connecting a computer, ensure that it is the last
device to be turned on after all the connections are made.
Ensure the operation manuals of the devices to be connected have been read before making connections.
When connecting with the RGB cable
(Connecting to COMPUTER/COMPONENT 1 or 2: The illustration shown below is for the former.)
Supplied
RGB cable
accessory
Computer
To audio output terminal
To COMPUTER/
To AUDIO input terminal
COMPONENT 1
input terminal
To RGB output terminal
RGB cable
*
ø3.5 mm stereo or mono audio cable
(commercially available or available as Sharp service part QCNWGA038WJPZ)
*
When using the ø3.5 mm mono audio cable, the volume level will be half of when using the ø3.5 mm stereo audio cable.
Note
• See page 65 “Computer Compatibility Chart” for a list of computer signals compatible with the projector.
Use with computer signals other than those listed may cause some of the functions to not work.
• A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest
Macintosh Dealer.
• Depending on the computer you are using, an image may not be projected unless the computer’s
external output port is switched on. (e.g. Press “Fn” and “F5” keys simultaneously when using a
SHARP notebook computer). Refer to the specific instructions in your computer’s operation manual to
enable your computer’s external output port.
-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to a Computer
When connecting with a DVI digital cable
The projector employs the DVI digital input terminal for direct input of Digital Video signals from a
computer.
Computer
To DVI-D input terminal
To AUDIO input terminal
(for DVI-D)
To DVI digital
output terminal
DVI Digital cable
(commercially available)
To audio output
terminal
* ø3.5 mm stereo or mono audio cable
(commercially available or available as
Sharp service part QCNWGA038WJPZ)
*
When using the ø3.5 mm mono audio cable, the volume level will be half of when using the ø3.5 mm stereo audio cable.
-24
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to Video Equipment
The image quality is highest in order of the Component signal, the RGB signal, the S-video signal and the
Video signal. If your audio-visual equipment has a component output terminal or RGB output terminal, use the
COMPUTER/COMPONENT terminal 1 or 2 on the projector for video connection.
When connecting video equipment with a DVI output terminal
Video Equipment
To audio output terminals
To AUDIO input terminal
(for COMPUTER/COMPONENT 2, DVI-D)
To DVI-D
input terminal
ø3.5 mm stereo minijack to RCA audio cable
(commercially available)
DVI Digital cable (commercially available)
To DVI output terminal
Note
• Select the input signal type of the video equipment. See page 47.
• While the projector is connected to video equipment that has an HDMI output terminal, only the video
signal can be input to the projector. (Connect the AUDIO input terminal for audio input.)
• Depending on specifications of video equipment or HDMI to DVI digital cable, the signal transmission
may not work property. (The HDMI specification does not support all connections to video equipment
that has HDMI digital output terminal using HDMI to DVI digital cable.)
• For details on compatibility for connection, see support information on DVI connection provided by the
video equipment manufacturer.
When connecting video equipment with component video output terminal
(Connecting to COMPUTER/COMPONENT 1 or 2: The illustration shown below is for the former.)
Video Equipment
To audio output terminal
To component video output terminal
To COMPUTER/COMPONENT 1
input terminal
To AUDIO
input terminal
3 RCA (Component) to 15-pin D-sub cable
(optional: AN-C3CP2)
ø3.5 mm minijack to RCA audio cable (commercially available)
Note
• When you connect video equipment with a 21-pin RGB output (Euro-scart) to the projector, use a
commercially available cable that fits in the projector terminal you want to connect.
• The projector does not support RGBC signals via the Euro-scart.
-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to Video Equipment
When connecting video equipment with S-video output terminal
To audio output terminal
To S-VIDEO input terminal
To AUDIO input terminal
To S-video output terminal
Video Equipment
S-video cable (commercially available)
RCA audio cable
(commercially available)
When connecting video equipment with video output terminal
To audio output terminal
To video output terminal
To VIDEO input terminal
To AUDIO input terminal
Video Equipment
RCA audio cable
Composite video cable (commercially available)
(commercially available)
Note
• When you connect video equipment with a 21-pin RGB output (Euro-scart) to the projector, use a com-
mercially available cable that fits in the projector terminal you want to connect.
-26
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling the Projector by a Computer
When the RS-232C terminal on the projector is connected to a computer, the computer can be used to control
the projector and check the status of the projector. Refer to the “SETUP MANUAL” contained on the supplied
CD-ROM for “RS-232C Specifications and Commands”.
When connecting to a computer using an RS-232C serial control cable and a DIN-D-sub RS-232C adaptor
Supplied
DIN-D-sub
accessory
RS232C adaptor
To RS-232C terminal
Computer
DIN-D-sub
RS-232C adaptor
To RS-232C terminal
RS-232C serial control cable (cross type, commercially available)
Note
• The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the
operation manual of the computer for details.
Info
• Do not connect the RS-232C cable to a port other than the RS-232C terminal on the computer. This may
damage your computer or projector.
• Do not connect or disconnect an RS-232C serial control cable to or from the computer while it is on. This
may damage your computer.
-27
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling the Projector by a Computer
When connecting to the LAN terminal using a LAN cable
TX/RX LED (yellow)
Illuminates when transmitting/receiving data.
LINK LED (green)
Illuminates when linked.
HUB
or
* To ensure safety, do not connect the
LAN terminal with any cables such
as a telephone line that may cause
excessive voltage.
Computer
LAN cable (Category 5 type, commercially available)
To LAN terminal
Note
• When connecting to hub, use straight-through Category 5 (CAT.5) type cable (commercially available).
• When connecting to computer, use cross-over Category 5 (CAT.5) type cable (commercially available).
Connecting to a Monitor with RGB InputTerminal
You can display computer images on both the projector and a separate monitor using two sets of RGB cables.
Supplied
accessory
Computer
Monitor
RGB cable
To COMPUTER/
COMPONENT 1
input terminal
To RGB output
terminal
To MONITOR OUT terminal
To RGB input terminal
RGB cable
RGB cable (commercially available)
-28
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to an Amplifier or Other Audio Equipment
Audio signals input from equipment connected to each audio input terminal of the projector can be output to audio equipment.
Amplifier
To AUDIO output terminal
(MONITOR OUT)
To audio input terminal
ø3.5 mm minijack to
RCA audio cable
(commercially available)
Note
• Turn off the power of both the projector and audio equipment when connecting.
• When turning off the power in the case of connecting an amplifier or other audio equipment, first turn off
the power of the amplifier and then turn off the power of the projector.
• By using external audio components, the volume can be amplified for better sound.
• For details on Variable Audio Output (VAO) and Fixed Audio Output (FAO), see page 52.
-29
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning the Projector On/Off
Supplied
accessory
Power cord
Connecting the Power Cord
Plug the supplied power cord into the AC
socket on the rear of the projector. Then plug
into the AC outlet.
Turning the Projector On
Before performing the steps in this section,
connect any equipment that you use with the
projector. (See pages 23-29.)
AC socket
To AC outlet
Remove the lens cap and press
STANDBY/ON on the projector or ON
on the remote control.
Info
• When “Auto Restart” is set to “On”:
If the power cord is unplugged from the outlet or the
breaker switch is turned off when the projector is on, then
the projector automatically turns on when the power cord
is plugged into the AC outlet or the breaker switch is turned
on. (See page 51.)
• The power indicator illuminates green.
• After the lamp indicator illuminates, the projec-
tor is ready to start operation.
•
English is the factory preset language. If you want to
change the on-screen display to another language, change
the language according to the procedure on page 50.
Note
• The lamp indicator illuminates or blinks, in-
dicating the status of the lamp.
Green: The lamp is on.
Lamp
Power indicator
indicator
Blinking green: The lamp is warming up.
Red: The lamp is shut down abnor-
mally or the lamp should be
replaced.
When switching on the projector, a slight flicker-
ing of the image may be experienced within the
first minute after the lamp has been illuminated.
This is normal operation as the lamp's control
circuitry is stabilizing the lamp output charac-
teristics. This does not indicate malfunction.
STANDBY/ON button
•
ON button
STANDBY
button
• If the projector is put into standby mode and
immediately turned on again, the lamp may
take some time to illuminate.
• When System Lock is set, the keycode in-
put box appears.To cancel the keycode set-
ting, input the keycode that you have already
set. See page 52 for details.
▼On-screen Display
Turning the Power Off (Put-
ting the Projector into Standby Mode)
Press STANDBY/ON on the projector or
STANDBY on the remote control, then press
that button again while the confirmation mes-
sage is displayed, to put the projector into
standby mode.
Info
•
Direct Power Off function:
You can unplug the power cord from the AC outlet
even if the cooling fan is still running.
-30
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Projection
Using the Adjustment
Feet
The height of the projector can be adjusted
using the adjustment feet when the screen is
located higher than the projector, the screen
is inclined or when the installation site is
slightly inclined.
Top View
Side View
Lens
center
Install the projector so that it is as perpen-
dicular to the screen as possible.
1
2
Press the Height Adjustment but-
tons.
• The adjustment feet come out.
Lift the projector to adjust its
height and remove your hands
from the Height Adjustment but-
Adjustment foot
Height Adjustment button
tons
.
• The projector is adjustable up to approxi-
mately 9 degrees.
3 Rotate the Tilt dial to finely ad-
just the horizontal tilt of the pro-
jector.
• The inclination is adjustable within ap-
proximately 2 degrees.
• When adjusting the height of the pro-
jector, trapezoidal distortion occurs.
When “Auto V-Keystone” of the “SCR-
ADJ” menu is set to “On” (see page 49),
keystone correction functions automati-
cally to correct trapezoidal distortion.
When you want to adjust the automati-
cally corrected image, use the manual
keystone correction. (See page 32.)
Info
• Do not press the Height Adjustment button
when the adjustment feet come out without
firmly holding the projector.
Tilt dial
• Do not hold the lens when lifting or lower-
ing the projector.
• When lowering the projector, be careful not
to get your fingers caught in the area be-
tween the adjustment foot and the projector.
-31
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Projection
KEYSTONE
button
MOUSE/Adjustment
buttons ('/"/\/|)
Correcting Trapezoidal
Distortion
Auto V-Keystone Correction
RETURN button
When the image is projected either from the top
or from the bottom towards the screen at an angle,
the image becomes distorted trapezoidally.
The function for correcting trapezoidal distortion
is called Keystone Correction.
"On-screen Display (Keystone Correction mode)
This projector is equipped with an “Auto V-Key-
stone Correction” function that automatically cor-
rects any trapezoidal distortion within the pro-
jected image. The correction is made automatically
provided the vertical incline or decline is within
12 degrees.
H&V KEYSTONE
END
TESTPATTERN
H: 0
V: 0
ADJUST
RESET
Vertical Keystone Correction
(Adjustment with ' / "
)
Note
• When not using the Auto V-Keystone Cor-
rection function, set “Auto V-Keystone” on
the “SCR-ADJ” menu to “Off”.
Manual Keystone Correction
When you want to make fine adjustments after the
Auto V-Keystone Correction function has been acti-
vated, or when you want to make corrections without
using the Auto V-Keystone Correction function, you
can make corrections manually using the following
procedure.
Horizontal Keystone Correction
(Adjustment with \ / |
)
1
Press KEYSTONE on the remote
control to enter the Keystone Correc-
tion mode.
• You can also use KEYSTONE on the
projector.
2 Press ' or " to parallelize the
left and right sides, or press
\ or | to parallelize the upper
and lower sides of the projected
Note
image.
• You can also adjust the Keystone Cor-
rection using the '/" and \/| buttons
on the projector.
• Press RETURN to return to the default set-
ting.
• Straight lines or the edges of images may
appear jagged while adjusting the image.
•
The Manual Keystone Correction can be
adjusted up to an angle of approximately
50 degrees vertically and approximately
30 degrees horizontally.
3 Press KEYSTONE
.
• The on-screen display of the Keystone
Correction mode will disappear.
• You can also use KEYSTONE on the
projector.
-32
Download from Www.Somanuals.com. All Manuals Search And Download.
Focus ring
Zoom knob
Adjusting the Lens
The image is focused and adjusted to the screen
size using the focus ring or zoom knob on the
projector.
1 The focus is adjusted by rotat-
ing the focus ring.
2 Zooming is adjusted by moving
the zoom knob.
-33
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Projection
Switching the Input Mode
VOL +/–
(Volume)
buttons
AV MUTE
buttons
Select the appropriate input mode for the con-
nected equipment.
Press COMPUTER1/2, DVI, S-VIDEO
or VIDEO on the remote control to se-
lect the input mode.
COMPUTER 1,
COMPUTER 2,
DVI, S-VIDEO,
VIDEO buttons
• When you press INPUT on the projector or DVI
on the remote control, the INPUT list appears.
Press '/" to switch the INPUT mode.
Adjusting the Volume
Press VOL +/– on the remote control or –\/
|+ on the projector to adjust the volume.
On-screen display
Note
• Pressing VOL–/–\ will lower the volume.
• Pressing VOL+/|+ will raise the volume.
• When the projector is connected to exter-
nal equipment, the volume level of the ex-
ternal equipment changes in accordance
with the volume level of the projector. Set
the projector’s volume to the lowest level
when turning the projector on/off or when
changing the input signal.
• When you do not want to output the sound
from the projector’s speaker while the pro-
jector is connected to external equipment,
set “Speaker” in “PRJ-ADJ” menu to “Off”.
(See page 51.)
Displaying the Black
Screen and Turning off
the Sound Temporarily
Press AV MUTE on the remote control to
temporarily display a black screen and turn
off the sound.
On-screen display
Note
• Pressing AV MUTE again will turn the pro-
jected image back on.
-34
Download from Www.Somanuals.com. All Manuals Search And Download.
MOUSE/Adjustment
buttons ('/"/\/|)
Switching the Eco+Quiet
Mode
BREAK TIMER
button
PressECO+QUIETtoswitchtheEco+Quiet
mode between on and off.
AUTO SYNC
button
FREEZE
button
• When the Eco+Quiet Mode is set to “ON”, the sound
of the cooling fan will turn down, the power consump-
tion will decrease, and the lamp life will extend.
ECO+QUIET
button
Note
• Refer to “Checking the Lamp Life Status” on
page 53 for details of the Eco+Quiet mode.
Displaying and Setting the
Break Timer
Auto Sync
(Auto Sync Adjustment)
1 Press BREAK TIMER.
• The timer starts to count down from 5 min-
utes.
Auto Sync function works when detecting input
signal after the projector turns on.
On-screen display
Press AUTO SYNC to manually adjust
with Auto Sync function.
2 Press '/"/\/| to adjust the length
Note
of the break time.
• When the optimum image cannot be achieved
with Auto Sync adjustment, use manual adjust-
ments. (See page 47.)
• Increases with ' or |
5 minutes s 6 minutes s 60 minutes
• Shortens with \ or "
4 minutes s 3 minutes s 1 minute
• The break time can be set in units of one
minute (up to 60 minutes).
Freezing a Moving Image
Canceling the break timer display function
Press BREAK TIMER.
1 Press FREEZE.
• The projected image is frozen.
Note
• Break Timer does not function while the projec-
tor is operating the “Auto Sync”, “FREEZE” or
“AV MUTE” functions.
2 Press FREEZE again to return to
the moving image from the cur-
rently connected device.
-35
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Projection
MOUSE/Adjustment
buttons ('/"/\/|)
Displaying an Enlarged
Portion of an Image
Graphs, tables and other portions of projected
images can be enlarged. This is helpful when
providing more detailed explanations.
MAGNIFY
buttons
RETURN
button
PICTURE MODE
button
1 Press
MAGNIFY on the remote
control.
• Enlarges the image.
• Pressing or
MAGNIFY enlarges or
reduces the projected image.
Note
Selecting the Picture Mode
You can select the appropriate picture mode for
the projected image, such as movie or video
game.
Press
.
×1 ×2 ×3 ×4 ×9
Press
.
Press PICTURE MODE.
• You can change the location of the en-
larged image using ', ", \ and |.
• When pressing PICTURE MODE, the picture mode
changes in the following order:
STANDARD PRESENTATION
MOVIE GAME sRGB
2 Press RETURN on the remote con-
trol to cancel the operation.
Note
• The magnification then returns to ×1.
• See page 45 for details on the picture mode.
* “sRGB” is displayed only when RGB signal is input.
Note
• The selectable magnifications differ de-
pending on the input signal.
• In the following cases, the image will re-
turn to the normal size (×1).
- When switching the INPUT mode.
- When RETURN has been pressed.
- When the input signal is changed.
- When the input signal resolution and re-
fresh rate (vertical frequency) change.
- When the Resize mode is changed.
- When the Picture mode is changed.
- When the Progressive mode is changed.
-36
Download from Www.Somanuals.com. All Manuals Search And Download.
Resize Mode
This function allows you to modify or customize
the resize mode to enhance the input image. De-
pending on the input signal, you can choose a
desired image.
RESIZE button
Press RESIZE.
• See page 49 for setting on menu screen.
COMPUTER
NORMAL
SVGA (800 × 600)
FULL
DOT BY DOT
800 × 600
1024 × 768
1152 × 864
1400 × 1050
1280 × 1024
—
STRETCH
XGA (1024 × 768)
4:3 aspect ratio
1068 × 800
SXGA (1152 × 864)
SXGA+ (1400 × 1050)
SXGA (1280 × 1024)
1280 × 720
1280 × 720
1280 × 800
1000 × 800
1280 × 720
1280 × 722
1280 × 720
1280 × 768
1280 × 800
1360 × 768
1360 × 768
1366 × 768
—
Other aspect ratios
1366 × 768
1280 × 768
—
1280 × 720
1280 × 800
—
Output screen image
Input signal
Computer
Image Type
NORMAL
FULL
DOT BY DOT
STRETCH
Resolution
XGA and below
*1
*3
Resolution
higher than
XGA
4:3 aspect ratio
*1
SXGA
(1280 1024)
5:4 aspect ratio
16:9 aspect ratio
*2
—
1280 720
*1
*1
*2
—
1360 768
1366 768
16:9 aspect ratio
*1
*1
1280 768
1280 800
*2
15:9 aspect ratio
16:10 aspect ratio
—
*2
—
: Cutout area on which images cannot be projected
: Area where the signals are off screen
*1 The Image Shift function can be used for these images.
*2 Same as NORMAL mode.
*3 In case SXGA+ input.
-37
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Projection
VIDEO/DTV
Input signal
Video/DTV
Output screen image
Image Type
NORMAL
AREA ZOOM
V-STRETCH
STRETCH
*1
*1
*1
4:3 aspect ratio
480I, 480P,
576I, 576P,
NTSC, PAL,
SECAM
Squeeze
Letter box
*1
16:9 aspect ratio
720P, 1035I,
1080I, 1080P
*1
*1
16:9 aspect ratio
16:9 aspect ratio
*2
—
540P
*1
16:9 aspect ratio
(4:3 aspect ratio in 16:9)
: Cutout area on which images cannot be projected
: Area on which the image is not included in the original signals
*1 The Image Shift function can be used for these images.
*2 Same as NORMAL mode.
About Copyrights
• When using the RESIZE function to select an image size with a different aspect ratio to a TV program or
video image, the image will look different from its original appearance. Keep this in mind while choosing an
image size.
• The use of the Resize or Keystone Correction function to compress or stretch the image for commercial
purposes/public displays in a café, hotel, etc. may be an infringement of copyright protected by law for
copyright holders. Please use caution.
-38
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Remote Control as the Wireless Computer Mouse
When connecting the projector and the computer with a USB cable, you can use the remote control as the
computer mouse.
If the computer is placed too far away from the projector to be connected via the USB cable, the separately
sold remote receiver (AN-MR2) makes it possible to operate the projector with the remote control. For de-
tails, see the operation manual of the receiver.
Connecting with a USB cable
Computer
USB terminal
To USB terminal
Point the remote control at
the USB remote receiver
(AN-MR2, optional)
USB cable
(commercially available or available as Sharp service part
QCNWGA014WJPZ)
or
The mouse pointer can be operated in the
following way after it is connected.
MOUSE/Adjustment
buttons ('/"/\/|)
■ When moving the cursor
Press MOUSE/Adjustment buttons ('/"/\/|).
■ When left-clicking
R-CLICK button
Press L-CLICK.
■ When right-clicking
Press R-CLICK.
PAGE Up/Down buttons
L-CLICK button
■ When your computer supports only a
one-click mouse (such as Macintosh)
Press L-CLICK or R-CLICK.
L-CLICK and R-CLICK have common function.
■ When using [Page Up] or [Page Down]
Same as the [Page Up] and [Page Down] keys on a computer keyboard.
Press PAGE UP or PAGE DOWN PAGE.
Note
• This function only works with the Microsoft® Windows® OS and Mac OS®. However, this function does not
work with the following operation systems that do not support USB.
• Versions earlier than Windows® 95
• Versions earlier than Windows® NT4.0
• Versions earlier than Mac OS® 8.5
• You cannot use this function when displaying the menu screen.
• Confirm that the computer recognizes the USB connection.
-39
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Items
The following shows the items that can be set in the projector.
“Picture” menu
Main Menu
Sub Menu
Picture
Standard
Presentation
Movie
Picture Mode
Page 45
Page 45
Game
sRGB*1
Contrast
Bright
Color
Tint
-30
-30
-30
-30
-30
-30
-30
+30
+30
+30
+30
+30
+30
+30
*2
*2
*2
Sharp
Red
Blue
Page 45
CLR Temp
5500K
6500K
7500K
8500K
9300K
10500K
Page 45
*3
*3
Progressive
3D Progressive
2D Progressive
Page 46
Film Mode
Page 46
DNR
Auto
Off
Off
Level 1
Level 2
Level 3
Page 46
MNR
Off
Level 1
Level 2
Level 3
Page 46
Eco+Quiet Mode
Page 46
Reset
On
Off
Page 45
*1 Item when inputting RGB signal through COMPUTER/COMPONENT 1, 2 or DVI-D
*2 Items when inputting Component signal through COMPUTER/COMPONENT 1 or 2, or when selecting VIDEO or
S-VIDEO
*3 “Progressive” and “Flim Mode” can be adjusted only when 480I, 576I, 1035I or 1080I signal is input.
-40
Download from Www.Somanuals.com. All Manuals Search And Download.
“Signal adjustment (SIG-ADJ)” menu
Main Menu
*4
SIG-ADJ
Clock
Phase
H-Pos
V-Pos
Reset
-150 +150
-30 +30
*4
*5
*5
*5
Page 47
-150 +150
-60 +60
Page 47
Resolution
Page 47
Auto Sync
On
Off
Page 47
*6
Signal Type
Auto
RGB
Component
Page 47
*7
*8
Dynamic Range
Auto
Standard
Enhanced
Page 48
Video System
Auto
PAL
Page 48
SECAM
NTSC4.43
NTSC3.58
PAL-M
PAL-N
PAL-60
Signal Info
Page 48
*4 Item when inputting RGB signal through COMPUTER/COMPONENT 1 or 2
*5 Item when inputting COMPUTER/COMPONENT 1 or 2
*6 Item when selecting COMPUTER/COMPONENT 1, 2 or DVI-D
*7 Item when selecting DVI-D
*8 Item when selecting VIDEO or S-VIDEO
“Screen adjustment (SCR-ADJ)” menu
Main Menu
Sub Menu
SCR-ADJ
Resize
Normal
Full
Page 49
Page 49
Dot By Dot
Area Zoom
V-Stretch
Stretch
Image Shift -40
+40
+60
Page 49
H-Keystone -60
Page 49
V-Keystone -100 +100
Page 49
Auto V-Keystone
Page 49
On
Off
OSD Display
On
Off
Page 50
Background
Logo
Blue
None
Page 50
Menu Position
Center
Upper Right
Lower Right
Upper Left
Lower Left
Page 50
Front
PRJ Mode
Ceiling + Front
Rear
Page 50
Ceiling + Rear
English
polski
Language
Deutsch
Español
Nederlands
Français
Italiano
Magyar
Türkçe
Page 50
Svenska
Português
-41
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Items
“Projecter adjustment (PRJ-ADJ)” menu
Main Menu
Sub Menu
PRJ-ADJ
Auto Power Off
Page 51
Auto Restart
Page 51
On
Off
Page 51
On
Off
System Sound
Page 51
Speaker
On
Off
On
Off
Page 51
FAO
VAO
Audio Out
Page 51
Monitor Out
Page 51
Enable
Disable
LAN/RS232C
Page 51
RS-232C
Enable
Disable
9600 bps
38400 bps
115200 bps
Page 52
Fan Mode
Normal
High
Page 52
System Lock
Old Code
New Code
Reconfirm
Pages 52 and 53
All Reset
Page 53
Lamp Timer (Life)
Page 53
“Network” menu
Main Menu
Old Password
New Password
Reconfirm
Network
Password
Page 54
Page 54
DHCP Client
Page 55
TCP/IP
On
Off
*1
*2
*2
IP Address
Subnet Mask
Gateway
Page 55
MAC Address
Page 55
Projector
Page 55
*1 Adjustable only when DHCP Client is set to “Off”
*2 Display only
-42
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menu Screen
Adjustment
buttons ('/"/\/|)
MOUSE/Adjustment
buttons ('/"/\/|)
ENTER button
ENTER
button
MENU button
MENU button
RETURN button
RETURN button
• Press RETURN to
return to previous
screen when the
menu is displayed
Menu Selections (Adjustments)
Example: Adjusting “Bright”.
• This operation can also be performed by using the buttons on the projector.
Example: “Picture” screen menu
Menu item
1 Press MENU.
• The “Picture” menu screen for the se-
lected input mode is displayed.
Picture
SIG
SCR
PRJ
Standard
Net.
Picture Mode
Contrast
Bright
0
0
0
0
0
0
0
2 Press | or \ and select “Pic-
Color
ture” to adjust.
Tint
Sharp
Red
Blue
CLR Temp
Progressive
Film Mode
DNR
7500K
3D Progressive
Auto
Off
Off
MNR
Off
Eco+Quiet Mode
Reset
SEL./ADJ.
RETURN
ENTER
END
-43
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menu Screen
Picture
SIG
SCR
PRJ
Net.
3 Press ' or " and select
“Bright” to adjust.
Picture Mode
Contrast
Bright
Standard
0
0
0
0
0
0
0
• The selected item is highlighted.
Color
Tint
Sharp
Red
Blue
CLR Temp
Progressive
Film Mode
DNR
7500K
3D Progressive
Auto
Off
To adjust the pro-
jected image while
watching it
Off
Off
MNR
Eco+Quiet Mode
Reset
SEL./ADJ.
RETURN
ENTER
END
Items to be adjusted
Press ENTER.
• The selected item (e.g. “Bright”) is dis-
played by itself at the bottom of the
screen.
–
Pict.
Clock
SIG ADJ
SCR
PRJ
Net.
0
0
0
0
Phase
H-Pos
V-Pos
• When pressing ' or ", the following
item (“Red” after “Bright”) will be dis-
played.
Reset
Press ENTER.
The item displayed by itself
Note
Picture
• Press ENTER again to return to the
previous screen.
Bright
0
SEL./ADJ.
Rtn. Menu
Rtn. Menu
END
Picture
SIG
SCR
PRJ
Net.
4 Press \ or | to adjust the item
selected.
Picture Mode
Contrast
Bright
Standard
0
1 5
0
• The adjustment is stored.
Color
Tint
0
Sharp
0
Red
0
Blue
0
CLR Temp
Progressive
Film Mode
DNR
7500K
3D Progressive
Auto
Off
Off
5 Press MENU.
MNR
Off
Eco+Quiet Mode
Reset
• The menu screen will disappear.
SEL./ADJ.
RETURN
ENTER
END
Note
• Menu buttons do not function while the projector is operating the “Auto Sync”, “Break Timer”, “FREEZE”,
or “AV MUTE” functions.
-44
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Adjustment (“Picture” menu)
Menu operation
Page 43
Picture
SIG
SCR
PRJ
Net.
2
Adjusting the Image
Picture Mode
Contrast
Bright
Standard
1
2
0
0
0
0
0
0
0
Adjustment items
Contrast
Bright
button
For less contrast.
For less brightness. For more brightness.
button
For more contrast.
\
|
Color
Tint
Sharp
Red
Color*1
For less color
intensity.
For more color
intensity.
Blue
CLR Temp
Progressive
Film Mode
DNR
7500K
3D Progressive
3
4
5
6
7
8
Tint*1
For making skin
tones purplish.
For making skin
tones greenish.
Auto
Off
Off
Sharp*1
Red*2
Blue*2
For less sharpness. For more sharpness.
MNR
For weaker red.
For weaker blue.
For stronger red.
For stronger blue.
Off
Eco+Quiet Mode
Reset
SEL./ADJ.
RETURN
ENTER
END
*1
Not adjustable/selectable in the RGB input mode.
Not adjustable/selectable when selecting “sRGB”
in “Picture Mode”.
*2
1
Selecting the Picture Mode
The default
Note
Selectable items
Description
settings of
CLR Temp
7500K
• “Red” and “Blue” cannot be set when selecting
“sRGB” in “Picture Mode”.
• To reset all adjustment items, select “Reset” and
press ENTER.
Standard
For standard image
Presentation Brightens portions of
image for more enhanced
presentations.
7500K
Movie
Game
*sRGB
Gives natural tint to the
projected image.
Gives sharpness to the
projected image.
For high fidelity reproduc-
tion of images from a
computer.
6500K
7500K
–
3
Adjusting the Color Temperature
Selectable items
5500K
Description
For lower color temperature for warmer,
reddish incandescent-like images.
6500K
7500K
8500K
9300K
10500K
• “sRGB” is displayed only when RGB signal is input.
• You can set or adjust each item in the “Picture”
menu to your preference. Any changes you make
are retained in memory.
For higher color temperature for cooler,
bluish, fluorescent-like images.
Note
Note
• Values on “CLRTemp” are only for general stan-
dard purposes.
• “CLR Temp” cannot be set when selecting
“sRGB” in “Picture Mode”.
• You can also press PICTURE MODE on the
remote control to select the picture mode. (See
page 36.)
• *sRGB is an international standard of color re-
production regulated by the IEC (International
Electrotechnical Commission).As the fixed color
area has been decided by the IEC, the images
are displayed in a natural tint based on an origi-
nal image, when “sRGB” is selected.
For additional information about the sRGB func-
tion, visit “http://www.srgb.com/”.
You cannot set the items, “Red”, “Blue” and
“CLR Temp”, when “sRGB” is selected.
Info
• When “sRGB” is selected, the projected image may be-
come dark, but this does not indicate a malfunction.
-45
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Adjustment (“Picture” menu)
Menu operation
Page 43
4
Selecting the Progressive Mode
Note
Selectable items
3D
Description
• Set a level so as to view a clearer picture.
Make sure to set “DNR” to “Off” in the
following cases:
• When the image is blurry.
• When the contours and colors of moving im-
ages drag.
Useful to display relatively slowmoving
images such as drama and documentary
more clearly.
Progressive
2D
Useful to display fast-moving images such
as sports and action films.
Progressive
• WhenTV broadcasts with weak signals are pro-
jected.
Note
• When the image is blurred or noisy, switch to
the optimal mode.
• When using progressive inputs, inputs are di-
rectly displayed so that “2D Progressive” and
“3D Progressive” cannot be selected.
Info
• This function is available for all signals with
VIDEO or S-VIDEO.
• This function is available for 480I, 480P, 576I
and 576P signals with COMPUTER1/2 or DVI.
5
Selecting the Film Mode
This function provides high-quality playback of
images originally projected at 24 fps, such as
movies on DVDs.
7
Mosquito Noise Reduction (MNR)
The so-called Mosquito Noise (flickering) can be
reduced.
Selectable items
Off
Level 1-3
Description
MNR does not function.
Sets the MNR level for viewing a
clearer picture.
Selectable items
Auto
Off
Description
Films are detected automatically.
Films are not detected.
Info
Note
• This function is available for all signals with
VIDEO or S-VIDEO.
• This function is available for 480I, 480P, 576I
and 576P signals with COMPUTER1/2 or DVI.
• When using progressive inputs, “Film Mode”
cannot be selected.
• The “Film Mode” function does not work when
“2D Progressive” is selected in “Progressive
Mode”.
8
Eco+Quiet Mode Setting
6
Reducing Image Noise (DNR)
Video digital noise reduction (DNR) provides high
quality images with minimal dot crawl and cross
color noise.
Fan
Sound
Selectable
items
Lamp life
Brightness
On
Off
Approx. 80%
Approx.
3,000
hours
Low
Selectable items
Off
Level 1–3
Description
DNR does not function.
Sets the DNR level.
100%
Approx.
2,000
Normal
hours
Note
• You can also use ECO+QUIET on the remote
control or on the projector to switch the Eco+Quiet
Mode. (See page 35.)
-46
Download from Www.Somanuals.com. All Manuals Search And Download.
Signal Adjustment (“SIG-ADJ” Menu)
Menu operation
Page 43
–
Pict.
Clock
SIG ADJ
SCR
PRJ
Net.
3
Auto Sync Adjustment
Used to automatically adjust a computer image.
0
0
0
0
Phase
H-Pos
V-Pos
1
Selectable items
On
Description
Reset
Resolution
Auto Sync
Signal Type
Dynamic Range
Video System
640 x 480
On
2
3
4
5
6
Auto Sync adjustment will occur when
the projector is turned on or when the
input signals are switched, when
connected to a computer.
Auto
Standard
Auto
Off
Auto Sync adjustment is not automati-
cally performed.
Signal Info : 800 x 600
7
H
60.3 kHz
/
V
37.8 Hz
SEL./ADJ.
RETURN
ENTER
END
Note
• Auto Sync adjustment is also performed by
pressing AUTO SYNC on the projector or on
the remote control.
• The Auto Sync adjustment may take some time
to complete, depending on the image of the
computer connected to the projector.
1
Adjusting the Computer Image
If the optimum image cannot be obtained with Auto
Sync adjustment, use the SIG-ADJ function.
Selectable items
Clock
Description
Adjusts vertical noise.
Phase
Adjusts horizontal noise (similar to
tracking on your VCR).
4
Signal Type Setting
This function allows you to select the input sig-
nal type RGB or Component for COMPUTER/
COMPONENT 1, 2 or DVI-D.
H-Pos
V-Pos
Centers the on-screen image by
moving it to the left or right.
Centers the on-screen image by
moving it up or down.
Selectable items
Auto
Description
Note
Input signals are automatically recog-
nized as RGB or component.
Set when RGB signals are received.
Set when Component signals are
received.
• To reset all adjustment items, select “Reset” and
press ENTER.
• The adjustable range of “H-Pos” (H-Position)
and “V-Pos” (V-Position) may vary depending
on the screen resolution of the computer.
RGB
Component
2
Resolution Setting
Ordinarily, the type of input signal is detected and the
correct resolution mode is automatically selected. How-
ever, for some signals, the optimal resolution mode in
“Resolution” on the “SIG-ADJ” menu may need to be
selected to match the computer display mode.
Note
• See “Checking the Input Signal” on page 48 for
information on the currently selected input sig-
nal.
-47
Download from Www.Somanuals.com. All Manuals Search And Download.
Signal Adjustment (“SIG-ADJ” Menu)
Menu operation
Page 43
5
7
Selecting the Dynamic Range
Checking the Input Signal
This function allows you to check the current in-
put signal information.
An optimum picture may not be displayed if a
DVI-D-capable device’s output signal type and the
projector’s input signal type do not match. If this
should occur, switch “Dynamic Range”.
Selectable items
Auto
Standard
Enhanced
Description
When the black levels of the image show
banding or appear faded, select the item
that results in the best picture quality. (In
most circumstances, “Standard” should
be selected.)
Note
• The Dynamic Range can be selected only when
“DVI-D” input mode is selected.
6
Setting the Video System
The video input system mode is factory preset
to “Auto”; however, a clear picture from the con-
nected audio-visual equipment may not be re-
ceived, depending on theVideo signal difference.
In that case, switch the Video signal.
Selectable items
Auto
PAL
SECAM
*NTSC4.43
NTSC3.58
PAL-M
PAL-N
PAL -60
* When reproducing NTSC signals in PAL video
equipment.
Note
• The Video signal can only be set in VIDEO or
S-VIDEO mode.
• When “Video System” is set to “Auto”, you may
not receive a clear picture due to signal differ-
ences. Should this occur, switch to the video
system of the source signal.
-48
Download from Www.Somanuals.com. All Manuals Search And Download.
Screen Adjustment (“SCR-ADJ” Menu)
Menu operation
Page 43
Pict.
SIG
SCR-ADJ
PRJ
Net.
3
Keystone Correction
Resize
Normal
1
2
Image Shift
H-Keystone
V-Keystone
0
0
0
When the image is projected either from the top or from
the bottom towards the screen at an angle, the image be-
comes distorted trapezoidally. The function for correct-
ing trapezoidal distortion is called Keystone Correction.
3
Auto V-Keystone
OSD Display
Background
Menu Position
PRJ Mode
On
On
Logo
Center
Front
English
4
5
6
7
8
Language
Auto V-Keystone Correction
Set “Auto V-Keystone” on the “SCR-ADJ” screen
menu to “On”.
SEL./ADJ.
RETURN
ENTER
END
Manual Keystone Correction
Set “Auto V-Keystone” on the “SCR-ADJ” screen
menu to “Off”. Select “V-Keystone”, and then
press \or |to parallelize the left and right sides
of the projected image with the slide bar. To
parallelize the upper and lower sides, select “H-
Keystone” and press \ or |.
1
Setting the Resize Mode
Note
• For details of the Resize mode, see pages 37
and 38.
Vertical Keystone Correction
• You can also press RESIZE on the remote con-
trol to set the resize mode. (See page 37.)
2
Adjusting the Image Position
You can move the projected image vertically.
Horizontal Keystone Correction
\ button
| button
Note
•
The Keystone Correction can be adjusted up to
an angle of approximately 12 degrees with “Auto
V-Keystone” and up to an angle of approximately
50 degrees with “V-Keystone” and approxi-
mately 30 degrees with “H-Keystone”.
Note
• This function only works in some RESIZE
modes. (See pages 37 and 38.)
• To reset this function, select “0”.
• When the screen is slanting or the image is de-
teriorated, set “Auto V-Keystone” to “Off”.
-49
Download from Www.Somanuals.com. All Manuals Search And Download.
Screen Adjustment (“SCR-ADJ” Menu)
Menu operation
Page 43
4
7
Setting the On-screen
Display
Reversing/Inverting Pro-
jected Images
This function allows you to turn the on-screen
messages on or off.
This projector is equipped with a reverse/invert
image function that allows you to reverse or in-
vert the projected image for various applications.
Selectable items
Description
Selectable items
Front
Description
Normal image (Projected from the front
of the screen)
On
Off
All On-screen Displays are displayed.
INPUT/VOLUME/AV MUTE/FREEZE/
AUTO SYNC/MAGNIFY/ “An invalid
button has been pressed.” are not
displayed.
Inverted image (Projected from the
front of the screen with an inverted
projector)
Ceiling + Front
Reversed image (Projected from the
rear of the screen or with a mirror)
Rear
5
Selecting a Startup and
Background Image
Reversed and inverted image (Pro-
jected with a mirror)
Ceiling + Rear
Selectable items
Description
SHARP default image
Note
Logo
Blue
• This function is used for the reversed image and
ceiling-mount setups. (See page 19.)
Blue screen
Black screen
None
6
Selecting the Menu
Screen Position
8
Selecting the On-screen
Display Language
Select “Menu Position” on the “SCR-ADJ” menu
and the desired position for the menu screen.
The projector can switch the on-screen display
language among 17 languages.
Selectable items
Center
Upper Right
Lower Right
Upper Left
Lower Left
Description
Displayed on the center of the image.
Displayed on the upper right of the image.
Displayed on the lower right of the image.
Displayed on the upper left of the image.
Displayed on the lower left of the image.
-50
Download from Www.Somanuals.com. All Manuals Search And Download.
Helpful Functions Set during Installation (“PRJ-ADJ” menu)
Menu operation
Page 43
Pict.
SIG
SCR
PRJ-ADJ
Net.
4
Speaker Setting
Auto Power Off
Auto Restart
System Sound
Speaker
On
1
2
3
4
5
6
7
8
9
0
q
On
On
This function allows you to set the audio output
of the internal speaker to “On” or “Off” such as
when the projector is connected to an external
amplifier.
On
Audio Out
FAO
Monitor Out
LAN/RS232C
RS-232C
Enable
Enable
9600bps
Normal
Disable
Fan Mode
Selectable items
Description
The audio signal is output from the internal
speaker.
System Lock
All reset
On
Off
The audio signal is not output from the
internal speaker.
Lamp Timer (Life)
[
0]h
[
0] min ( 100%)
w
SEL./ADJ.
RETURN
ENTER
END
5
Audio Output Type Setting
This function determines whether the audio level
output from the AUDIO output (MONITOR output)
terminal is fixed or variable by linking with VOL-
UME.
1
Auto Power Off Function
Selectable items
On
Description
The projector automatically enters the
standby mode when no input signal is
detected for 15 minutes or longer.
The Auto Power Off function will be
disabled.
Selectable items
FAO
(Fixed Audio strength with the volume level of the
Description
Audio output that does not vary in
Off
Output)
source projector.
VAO
(Variable
Audio Output)
Audio output that varies in strength with
the volume level of the source projector.
Note
• When the Auto Power Off function is set to “On”,
5 minutes before the projector enters the
standby mode, the message “Enter STANDBY
mode in X min.” will appear on the screen to
indicate the remaining minutes.
Info
• When “Audio Out”has been set to “VAO”, first make
sure to lower the volume of the projector before
turning the power on or off and when switching the
input.
2 Auto Restart Function
6
Monitor Output
LAN/RS232C
Selectable items
On
Description
If the power cord is unplugged from the
outlet or the breaker switch is turned off
when the projector is on, then the
projector automatically turns on when
the power cord is plugged into the AC
outlet or the breaker switch is turned on.
The projector does not turn on auto-
matically when the power cord is
plugged into the AC outlet or the
breaker switch is turned on.
7
When set to “Enable”, the function is activated
and power is consumed even in the standby mode.
It is recommended that the function be set to“Dis-
able”when it is not connected.This reduces power
consumption when the projector is in the standby
mode.
Off
Selectable items
Enable
Description
The function is activated even if the
projector is in standby mode.
The function is switched off when the
projector is in standby mode.
3
Setting the Confirmation
Sound (System Sound)
Disable
Selectable items
On
Description
A confirmation sound is made when the
projector turns on/off.
Note
• When you want to control the projector using
the LAN/RS232C function, select “Enable”.
Off
No confirmation sound is made.
-51
Download from Www.Somanuals.com. All Manuals Search And Download.
Helpful Functions Set during Installation (“PRJ-ADJ” menu)
Menu operation
Page 43
Setting/Changing the keycode
8
Selecting the Transmis-
sion Speed (RS-232C)
1 Select “System Lock”, then press
Make sure that both the projector and computer
are set for the same baud rate.
ENTER or |.
Selectable items
9600 bps
Description
2 Select “Next”, then press ENTER.
Transmission speed is slow.
• The screen for entering the keycode appears.
38400 bps
115200 bps
Transmission speed is rapid.
3 Press the 4 buttons on the remote
control or on the projector to enter
the preset keycode in “Old Code”.
• When setting the keycode for the first time,
press " on the projector for four times.
Note
• Refer to the “SETUP MANUAL” contained on
the supplied CD-ROM for RS-232C Specifica-
tions and Command Settings.
PRJ-ADJ
• Refer to the computer’s operation manual for
instructions for setting the computer’s baud rate.
Setting the System Lock
– – – –
– – – –
– – – –
Old Code
New Code
Reconfirm
9
Fan Mode Setting
This function changes the fan rotation speed.
Note
Selectable items
Normal
High
Description
• If you input a wrong keycode, the cursor
returns to the first point of the “Old Code”.
• The preset keycode is 4 " buttons on the
projector.When you press the " button four
times, the keycord input screen disappears.
Suitable for normal environments.
Select this when using the projector at
altitudes of approximately 1,500 meters
(4,900 feet) or more.
When “Fan Mode” is set to “High”, the fan rotation
speeds up, and the fan noise becomes louder.
4 Press the 4 buttons on the remote
control or on the projector to enter
the new keycode in “New Code”.
0
System Lock Function
This function prevents unauthorized use of the
projector. Once this function is activated, users
must enter the correct keycode each time the pro-
jector is turned on. We suggest you record the
keycode in a safe place where only autho-
rized users have access.
Note
• You cannot use the following buttons for
keycode: STANDBY/ON, ON, STANDBY,
ENTER, L-CLICK, R-CLICK/RETURN,
MENU, ECO+QUIET and BREAK TIMER
• System lock function recognizes each
button on the remote control or on the
projector as an individual button, even if
they share the same button name. If you
used the buttons on the projector in set-
ting your keycode, the keycode cannot
be canceled with the remote control.
Info
• If you lose or forget your keycode, contact your
nearest Sharp Authorized Projector Dealer or Ser-
vice Center (see page 68). Even if the product
warranty is valid, the keycode reset will incur a
charge.
PRJ-ADJ
Setting the System Lock
Old Code
* * * *
– – – –
– – – –
New Code
Reconfirm
-52
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu operation
Page 43
q
Returning to the Default
Settings
5
Enter the same keycode in “Re-con-
firm”.
This function allows you to initialize the settings
you have made in the projector.
Note
To cancel the keycode that you have al-
ready set
Note
• Press " on the projector for four times in steps
The following items or menu cannot be initialized.
• “SIG-ADJ” menu
Resolution
• “SCR-ADJ” menu
Language
4 and 5 above.
When the System Lock is set
• When System Lock is set, the keycode input screen
appears after the power is turned on. When it ap-
pears, enter the right keycode to start projection.
• “PRJ-ADJ” menu
Lamp Timer (Life)
System Lock
Input screen for keycode
– – – –
System Lock
Keylock Function
w Checking the Lamp Life
Status
Locking the Operation Buttons on
You can confirm the cumulative lamp usage time
and the remaining lamp life (percentage).
the Projector
Use this function to lock the operation but-
tons on the projector.
Lamp usage condition
“Life”
Remaining lamp life
100%
5%
■ Locking the Operation Buttons
Hold down ENTER on the projector for about 5 sec-
onds while the projector is being turned on.
Operated exclusively
while “Eco+Quiet Mode”
is “On”.
Operated exclusively
while “Eco+Quiet Mode”
is “Off”.
Approx.
Approx.
150 hours
3,000 hours
Approx.
▼On-screen Display
Approx.
Keylock function ON
2,000 hours 100 hours
• The keylock function does not affect the operation
with the remote control buttons.
• You cannot use the keylock function while the pro-
jector is warming up.
Note
• It is recommended that the lamp be changed
when the remaining lamp life becomes 5%.
• Remaining lamp life changes within the range
of the values shown depending on the frequency
at which “Eco+Quiet Mode” is switched to “On”
and “Off”. (See page 46.)
■ Taking the Keylock off
Hold down ENTER on the projector for about 5 seconds.
▼On-screen Display
Keylock function OFF
• The lamp life may vary depending on the us-
age condition.
• When the projector is in standby mode, you can
release the keylock by holding down ENTER and
STANDBY/ON on the projector simultaneously for
about 5 seconds.
Info
• Keylock cannot be set while the projector is: dis-
playing the “Menu” screens, in standby mode,
warming up, changing input signals, operating
“Auto Sync” function or on the “System Lock”
screen during warming up.
-53
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the Projector Network Environment (“Network” menu)
Menu operation
Page 43
Pict.
SIG
SCR
PRJ
Disable
Network
Changing the Password
Password
1
2
3
DHCP Client
TCP/IP
Off
1 Select “Password”, then press |.
• The screen for entering the password ap-
pears.
MAC Address
Projector
XX:XX:XX:XX:XX:XX
XX-XXXX
4
2 Enter the password in “Old Pass-
word” using ', ", | and \, then
press ENTER.
SEL./ADJ.
RETURN
ENTER
END
3 Enter the password in “New Pass-
word” using ', ", | and \, then
press ENTER.
1
Setting a Password
If you do not want others to change the setting
for the “Network” menu, set a password.
4 Enter the same password again in
“Reconfirm” using ', ", | and \,
then press ENTER.
Setting a Password
1 Select “Password”, then press |.
• The screen for entering the password ap-
pears.
Note
• If you do not need the password protection for
the “Network” menu settings anymore, press
ENTER without entering new password in steps
3 and 4.
Network
Setting the Password
– – – –
– – – –
– – – –
Old Password
New Password
Reconfirm
• To cancel the password settings, press RETURN.
If you forget the password
2 Press ' or " to set the first digit in
If you forget the password, perform the following
procedure to delete it, then set a new password.
“New Password”, then press |.
On the projector, press
3 Enter the remaining 3 digits, then
press ENTER.
• To return to the previous digit, press \.
Note
•
•
If ENTER is held down for more than 5 seconds, the
operation buttons on the projector will be locked. (See
page 53.)
You cannot use the buttons on the remote control to
delete the password.
4 Enter the same password in
“Reconfirm”, then press ENTER.
• The status for “Password” changes to “En-
able”.
Note
• Once after the password is set, you must enter
the password to change the “Network” menu
settings.
-54
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu operation
Page 43
Selectable items
IP Address
Description
Factory default setting:
192.168.150.002
Enter an IP address appropriate for the
network.
2
DHCP Client Setting
Connect the LAN cable before turning the pro-
jector on. If not, the DHCP Client function does
not work.
Subnet Mask Factory default setting:
255.255.255.000
Selectable items
On
Description
Obtains configuration parameters for
TCP/IP network automatically.
Sets the TCP/IP manually.
Set the subnet mask to the same as
that of the computer and equipment on
the network.
Off
Gateway
Factory default setting: 000. 000. 000.
000
* When not in use, set to “000. 000.
000. 000”.
Select “On” for “DHCP Client”. “Obtaining IP
Address...” appears, then the menu screen appears.
Confirm the parameters of IP Address, Subnet Mask
and Gateway on the TCP/IP screen.
If the DHCP server is not available, “Could not
obtain IP Address.” appears.
Note
In this case, set the TCP/IP manually. (See the item
3.)
• Confirm the existing network’s segment (IP ad-
dress group) to avoid setting an IP address that
duplicates the IP addresses of other network
equipment or computers. If “192.168.150.002”
is not used in a network with an IP address of
“192.168.150.XXX”, you don’t have to change
the projector IP address.
3
TCP/IP Setting
Set the TCP/IP manually.
• For details about each setting, consult your
network administrator.
1 Select “Off” for “DHCP Client”, then
press ENTER.
4 Confirming the
2 Select “TCP/IP”, then press ENTER.
Projector Information
You can confirm the MAC address and projector
name.
3 Enter “IP Address” using ', ", |
and \, then press ENTER.
Displayed items
Description
MAC Address The MAC address of the projector is
displayed.
Network
Setting the TCP/IP
Projector
The projector name is displayed.
1 9 2 . 1 6 8 . 1 5 0 . 0 0 2
2 5 5 . 2 5 5 . 2 5 5 . 0 0 0
0 0 0 . 0 0 0 . 0 0 0 . 0 0 0
IP Address
Subnet Mask
Gateway
Note
• For information on how to change the projector
name, see “SETUP MANUAL” contained in the
supplied CD-ROM.
4 Enter “Subnet Mask” using ', ",
| and \, then press ENTER.
5 Enter “Gateway” using ', ", | and
\, then press ENTER.
-55
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Cleaning the projector
Cleaning the lens
■ Ensure the power cord is unplugged before cleaning
■ Use a commercially available blower or lens clean-
ing paper (for glasses and camera lenses) for clean-
ing the lens. Do not use any liquid type cleaning
agents, as they may wear off the coating film on the
surface of the lens.
the projector.
■ The cabinet as well as the operation panel is made
of plastic. Avoid using benzene or thinner, as these
can damage the finish on the cabinet.
■ Do not use volatile agents such as insecticides on
the projector.
■ As the surface of the lens can easily get damaged,
be careful not to scrape or hit the lens.
Do not attach rubber or plastic items to the projec-
tor for long periods.
The effects of some of the agents in the plastic may
cause damage to the quality or finish of the projector.
Cleaning
aper
P
Cleaning the exhaust and intake vents
■ Use a vacuum cleaner to clean dust from the ex-
haust vent and the intake vent.
Mild detergent
diluted with water
Thinner
Wax
■ Wipe off dirt gently with a soft flannel cloth.
■ When the dirt is hard to remove, soak a cloth in a
mild detergent diluted with water, wring the cloth
well and then wipe the projector.
Strong cleaning detergents may discolor, warp or
damage the coating on the projector. Make sure to
test on a small, inconspicuous area on the projec-
tor before use.
Info
• If you want to clean the air vents during projec-
tor operation, ensure you press STANDBY/ON
on the projector or STANDBY on the remote
control and put the projector into standby mode.
After the cooling fan has stopped, unplug the
power cord from the AC socket and clean the
vents.
• The air filters should be cleaned every 100
hours of use. Clean the filters more often when
the projector is used in a dusty or smoky loca-
tion.
-56
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the Air Filter
• This projector is equipped with air filters
to ensure the optimal operating condition
of the projector.
STANDBY button
• Ask your nearest Sharp Authorized Pro-
jector Dealer or Service Center to ex-
change the filter (PFILDA022WJKZ) when
it is no longer possible to clean.
Replacing the Air Filter
1 Press STANDBY/ON on the pro-
jector or STANDBY on the remote
control to put the projector into the
standby mode.
STANDBY/ON
button
• Wait until the cooling fan stops.
2 Disconnect the power cord.
• Unplug the power cord from the AC socket.
3 Remove the filter cover.
• Turn over the projector. Pull down the car-
rying handle (1), grab the tab (2) and slide
open the filter cover (3).
AC socket
3
2
4 Remove the air filter.
• Pick the air filter up with your fingers and lift
it out of the filter cover.
1
Tab
-57
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the Air Filter
5 Place a replacement air filter.
• Place the new air filter onto the filter cover.
6 Replace the filter cover.
• Slide the filter cover in the direction of the
arrow to close it.
Note
• Ensure the filter cover is securely installed.The
power will not turn on unless it is correctly in-
stalled.
-58
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance Indicators
■ The warning lights on the projector indicate problems inside the projector.
■ If a problem occurs, either the temperature indicator or the lamp indicator will illuminate red, and
the projector will enter the standby mode. After the projector has entered the standby mode, follow
the procedures given below.
Maintenance Indicators
Power indicator
Lamp indicator
Temperature warning indicator
About the temperature warning indicator
If the temperature inside the projector increases, due to blockage of the air vents, or the setting location,
“
” will illuminate in the lower left corner of the picture. If the temperature keeps on rising, the lamp will
turn off and the temperature warning indicator will blink, the cooling fan will run for a further 90 seconds, and
then the projector will enter the standby mode. After “
” appears, ensure you perform the measures
described on page 60.
About the lamp indicator
■When the remaining lamp life becomes 5% or less, “ ” (yellow) and “Change The Lamp.” will be
displayed on the screen. When the percentage becomes 0%, it will change to “ ” (red), the lamp will
automatically turn off and then the projector will automatically enter the standby mode. At this time,
the lamp indicator will illuminate in red.
■
If you try to turn on the projector a fourth time without replacing the lamp, the projector will not turn on.
-59
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance Indicators
Maintenance indicator
Problem
Cause
Possible solution
Normal
Abnormal
• Relocate the projector to an area
with proper ventilation (see page
8).
• Blocked air intake
Temperature
warning
indicator
The internal
temperature is
abnormally high.
• Take the projector to your nearest
Sharp Authorized Projector Dealer
or Service Center (see page 68)
for repair.
• Clean the exhaust and intake
vents. (See page 56.)
Red on
(Standby)
Off
• Cooling fan break-
down
• Internal circuit failure
• Clogged air intake
• Disconnect the power cord from
the AC outlet, and then connect it
again.
The lamp does
not illuminate.
• The lamp is shut
down abnormally.
• Carefully replace the lamp. (See
page 62.)
• Take the projector to your nearest
Sharp Authorized Projector Dealer
or Service Center (see page 68)
for repair.
Red on
Red on
Green on
Green blinks
when the lamp
is warming up
Time to change
the lamp.
• Remaining lamp life
becomes 5% or less.
Lamp
indicator
The lamp does
• Burnt-out lamp
• Lamp circuit failure
• Please exercise care when
replacing the lamp.
(Standby) not illuminate.
• Securely install the lamp unit cover.
• If the power indicator blinks even
when the covers are securely
installed, or if the cooling fan does
not run normally, then contact your
nearest Sharp Authorized
Projector Dealer or Service Center
(see page 68) for advice.
• The filter cover, lamp
unit cover or lens
housing cover is
open.
• Cooling fan break-
down
Green on/
Red on
The power
Power
indicator
indicator blinks
Red blinks
in red when the
Green blinks
(Cooling)
projector is on.
Info
• If the temperature warning indicator illuminates and the projector enters the standby mode, check whether
any of the ventilation holes are blocked (see page 8) and then try turning the power back on.Wait until the
projector has cooled down completely before plugging in the power cord and turning the power back on.
(At least 10 minutes.)
• If the power is turned off for a brief moment due to power outage or some other cause while using the
projector, and the power supply recovers immediately after that, the lamp indicator will illuminate in red
and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace the power
cord in the AC outlet and then turn the power on again.
• The cooling fan keeps the internal temperature of the projector constant and this function is controlled
automatically. The sound of the cooling fan may change during operation because the fan speed may
change and this is not a malfunction.
-60
Download from Www.Somanuals.com. All Manuals Search And Download.
Regarding the Lamp
Lamp
■ It is recommended that the lamp unit (optional: AN-C430LP) be replaced when the remaining lamp
life becomes 5% or less, or when you notice a significant deterioration in the picture and color
quality. The lamp life (percentage) can be checked with the on-screen display. See page 53.
■ Purchase a replacement lamp unit of type AN-C430LP from your place of purchase, nearest Sharp
Authorized Projector Dealer or Service Center.
IMPORTANT NOTE TO U.S. CUSTOMERS:
The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service
of this projector under warranty, including lamp replacement, must be obtained through a Sharp Autho-
rized Projector Dealer or Service Center. For the name of the nearest Sharp Authorized Projector Dealer
or Service Center, please call toll-free: 1-888-GO-SHARP (1-888-467-4277).
Hg LAMP CONTAINS MERCURY For State Lamp Disposal Information
U.S.A. ONLY
Caution Concerning the Lamp
■ This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp
failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface
scratches or deterioration of the lamp due to a lapse of usage time.
The period of time up to failure largely varies depending on the individual lamp and/or the condition
and the frequency of use. It is important to note that failure can often result in the bulb cracking.
■ When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended
that the lamp be replaced with a new one immediately, even if the lamp appears to be operating
normally.
■ Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the
lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes
mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In
case of exposure to the gas, consult a doctor as soon as possible.
■ Should the lamp break, there is also a possibility that glass particles may spread inside of the
projector. In such a case, it is recommended you contact your nearest Sharp Authorized Projector
Dealer or Service Center to assure safe operation.
Replacing the Lamp
Caution
• Do not remove the lamp unit from the projector right after use.The lamp will be very hot and may cause burn
or injury.
• Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool
before removing the lamp unit.
■ Carefully change the lamp by following the instructions described in this section. *If you wish, you
may have the lamp replaced at your nearest Sharp Authorized Projector Dealer or Service Center.
* If the new lamp does not illuminate after replacement, take your projector to the nearest Sharp Authorized
Projector Dealer or Service Center for repair.
-61
Download from Www.Somanuals.com. All Manuals Search And Download.
Regarding the Lamp
Removing and Installing
the Lamp Unit
Optional
accessory
Lamp unit
AN-C430LP
Warning!
• Do not remove the lamp unit from the pro-
jector right after use. The lamp and parts
around the lamp will be very hot and may
cause burn or injury.
Info
STANDBY/ON
button
• Do not touch the glass surface of the lamp
unit or the inside of the projector.
• To avoid injury to yourself and damage to
the lamp, make sure you carefully follow
the steps below.
• Do not loosen other screws except for the
lamp unit cover and lamp unit.
1 Press STANDBY/ON on the
projector or STANDBY on the
remote control to put the projec-
tor into standby mode.
• Wait until the cooling fan stops.
AC socket
2 Disconnect the power cord.
• Unplug the power cord from the AC
socket.
• Leave the lamp until it has fully cooled
down (about 1 hour).
2
3
3 Remove the lamp unit cover.
• Loosen the user service screw (1) that
secures the lamp unit cover. Slide down
(2) and remove the lamp unit cover
(3).
1
User service screw
(for lamp unit cover)
4 Remove the lamp unit.
• Loosen the securing screws from the
lamp unit. Hold the lamp unit and pull it
in the direction of the arrow. At this time,
keep the lamp unit horizontal and do not
tilt it.
Securing screws
-62
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Insert the new lamp unit.
• Press the lamp unit firmly into the lamp
unit compartment. Fasten the securing
screws.
6 Replace the lamp unit cover.
• Align the lamp unit cover and slide it to
close. Then tighten the user service
screw to secure the lamp unit cover.
User service screw
(for lamp unit cover)
Info
• If the lamp unit and lamp unit cover are not
correctly installed, the power will not turn
on, even if the power cord is connected to
the projector.
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.
Info
• Make sure to reset the lamp timer only
when replacing the lamp. If you reset the
lamp timer and continue to use the same
lamp, this may cause the lamp to become
damaged or explode.
AC socket
• You can also reset the lamp timer via the
LAN.
(Refer to the SETUP MANUAL on the sup-
plied CD-ROM for details.)
Lamp indicator
STANDBY/ON button
1 Connect the power cord.
• Plug the power cord into the AC socket
of the projector.
ENTER button
" button
MENU button
2 Reset the lamp timer.
•
While simultaneously holding down ",
ENTER and MENU on the projector,
press STANDBY/ON on the projector and
keep all four buttons pressed down until
the lamp indicator starts blinking green.
• “LAMP 0000H” is displayed, indicating
that the lamp timer is reset.
-63
Download from Www.Somanuals.com. All Manuals Search And Download.
Storing the Projector
How to Use the
Storage Case
When storing the projector, attach the lens
cap to the lens, and place it in the supplied
storage case.
1 Open the cover of the storage
case.
2 Place the projector into the stor-
age case.
Lens cap
Info
• Ensure the projector has cooled down
sufficiently before placing it in the case.
• Ensure the lens cap is attached to the
lens for protection.
• Place the projector into the storage
case with the lens facing the
handle.
• Ensure the projector is held in place
by using the fixing band.
Fixing band
3 Close the cover of the storage
case.
4 Place the accessories in the front
pocket of the storage case.
Supplied accessories
(Remote control, etc.)
-64
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Compatibility Chart
Computer
• Multiple signal support
Pixel Clock: 12–170 MHz
Horizontal Frequency: 15–110 kHz
Vertical Frequency: 43–85 Hz
Sync signal: Compatible with TTL level
• Compatible with sync on green signal
The following is a list of modes that conform to VESA. However, this projector supports other signals
that are not VESA standards.
Horizontal Frequency
(kHz)
Vertical Frequency
(Hz)
Analog RGB
Support
Digital RGB
Support
Mode
Resolution
VESA
27.0
31.5
37.9
27.0
31.5
37.9
27.0
31.5
27.0
31.5
37.9
26.2
31.5
34.7
37.9
37.5
43.3
31.3
35.2
37.9
46.6
48.1
46.9
53.7
40.3
48.4
56.5
60.0
68.7
45.0
47.8
49.7
62.8
47.7
47.8
55.0
66.2
67.5
64.0
80.0
64.0
65.3
75.0
34.9
49.7
60.2
68.7
60
70
85
60
70
85
60
70
60
70
85
50
60
70
72
75
85
50
56
60
70
72
75
85
50
60
70
75
85
60
60
60
75
60
60
60
70
75
60
75
60
60
60
67
75
75
75
640 × 350
✔
✔
✔
640 × 400
720 × 350
VGA
720 × 400
✔
✔
640 × 480
✔
✔
SVGA
800 × 600
✔
✔
✔
✔
XGA
1024 × 768
1280 × 720
1280 × 768
1280 × 800
✔
WXGA
1360 × 768
1366 × 768
1152 × 864
SXGA
✔
✔
1280 × 1024
SXGA+
1400 × 1050
UXGA
1600 × 1200
640 × 480
MAC 13"
MAC 16"
MAC 19"
MAC 21"
832 × 624
1024 × 768
1152 × 870
Note
• This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD)
mode. Should this occur, turn off the LCD display on the notebook computer and output the display data
in “CRT only” mode. Details on how to change display modes can be found in your notebook computer’s
operation manual.
• When this projector receives 640 × 350 VESA format VGA signals, “640 × 400” appears on the screen.
• When projecting the RGB interlace signal using COMPUTER/COMPONENT 1, 2 or DVI-D with “Signal Type”
set to “Auto” or “RGB”, the image may not be projected as desired. In this case, use either Video or S-Video.
• Depending on the computer you are using, the output signal may not be faithful to the “Screen resolution”
adjustment. Check the settings of the computer’s signal output. If the settings cannot be changed, it is recom-
mended that the resolution be set to the one that corresponds to “1280 × 800”.
DTV
Signal
480
480P
540P
576
576P
720P
720P
Horizontal Frequency (kHz)
Vertical Frequency (Hz)
DVI Support
I
15.7
31.5
33.8
15.6
31.3
37.5
45.0
28.1
33.8
56.3
67.5
60
60
60
50
50
50
60
50
60
50
60
✔
I
✔
✔
✔
✔
✔
✔
✔
1080
1080
1080P
1080P
I
I
-65
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Check
Page
30
—
• Projector power cord is not plugged into the wall outlet.
• Power to the external connected devices is off.
• The selected input mode is wrong.
34
• The AV MUTE function is working.
34
• Cables incorrectly connected to the rear panel of the projector.
• Remote control batteries have run out.
23-29
15
•
External output has not been set when connecting notebook computer.
23
• The filter cover, lamp unit cover or lamp housing cover is not
installed correctly.
60
No picture and no sound
or projector does not start.
• If the connected DVI digital equipment is turned on before the
“DVI-D” input mode is selected on the projector, the image may
not be projected properly or may not be displayed at all. Ensure
that the appropriate input mode has been selected on the
projector before you turn on the connected equipment.
24
• Cables incorrectly connected to the rear panel of the projector.
• “Bright” is set to minimum position.
23-29
45
• Depending on the computer you are using, an image may not
be projected unless the signal output setting of the computer is
switched to the external output. Refer to the computer’s
operation manual for how to switch its signal output settings.
—
Sound is heard but no
picture appears.
• Image adjustments are incorrectly set.
45
(Video, S-Video Input only)
• Video input system is incorrectly set.
(COMPUTER/COMPONENT 1, 2, DVI-D only)
• Input signal type (RGB/Component) is incorrectly set.
48
47
Color is faded or poor.
• Adjust the focus.
• The projection distance exceeds the focus range.
33
19
—
• There is fog on the lens. If the projector is carried from a cold
room into a warm room, or if it is suddenly heated,
condensation may form on the surface of the lens and the
image will become blurred. Please set up the projector at least
one hour before it is to be used. If condensation should form,
remove the power cord from the wall outlet and wait for it to
clear.
Picture is blurred;
noise appears.
(Computer Input only)
• Perform “SIG-ADJ” Adjustments. (“Clock” Adjustment)
• Perform “SIG-ADJ” Adjustments. (“Phase” Adjustment)
• Noise may appear depending on the computer.
47
47
—
• Cables incorrectly connected to the rear panel of the projector.
• Volume is set to minimum.
23-29
34
• When the projector is connected to an external device and the
volume is set to minimum, the sound is not output even if you
turn up the volume of the external device.
Picture appears but no
sound is heard.
• “Speaker” is set to “Off”.
51
47
—
Data image is not
centered.
• Make the necessary adjustments of each item in the “SIG-ADJ”
menu.
• Depending on the computer you are using, the output resolution
signal may be different from the one you have set. For details,
refer to the operation manual of the computer.
-66
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Check
Page
—
An unusual sound is
occasionally heard
from the cabinet.
• If the picture is normal, the sound is due to cabinet shrinkage
caused by room temperature changes. This will not affect
operation or performance.
Maintenance
indicator illuminates or
blinks in red.
• See “Maintenance Indicators”.
59
53
The projector cannot be • The keylock is set.
turned on or put into the
standby mode using the
STANDBY/ON button on
the projector.
If the keylock is set to ON, all the buttons are locked.
Picture is green with
component input signals
(COMPUTER/
• Change the input signal type setting.
47
COMPONENT 1, 2, DVI-D)
.
Picture is pink (no green)
with RGB input signals
(COMPUTER/
COMPONENT 1, 2, DVI-D)
.
Picture is too bright and • Image adjustments are incorrectly set.
45
48
whitish.
The black levels of the • Select the Dynamic Range setting (“Standard” or “Enhanced”)
image show banding or
appear faded when DVI-
D is selected.
that results in the best picture quality.
The cooling fan
becomes noisy.
• When temperature inside the projector increases, the cooling
fan runs faster.
—
The lamp does not light • The lamp indicator is illuminating in red.
59
up even after the
projector turns on.
Replace the lamp.
The lamp suddenly turns
off during projection.
The image sometimes • Cables incorrectly connected to the projector or the connected
23-29
flickers.
equipment works improperly.
• If this happens frequently, replace the lamp.
The lamp takes a long • The lamp will eventually need to be changed.
62
62
time to turn on.
The lamp has reached the end of its life. Replace the lamp.
Picture is dark.
The remote control
cannot be used.
• Operate the remote control while pointing it at the projector’s
remote control sensor.
• The remote control may be too far away from the projector.
• If direct sunlight or a strong fluorescent light is shining on the
projector’s remote control sensor, place the projector where it
will not be affected by strong light.
15
• The batteries may be depleted or inserted incorrectly. Make
sure the batteries are inserted correctly or insert new ones.
15
This projector is equipped with a microprocessor. Its performance could be adversely affected by
incorrect operation or interference. If this should happen, unplug the projector and plug it in again
after more than 5 minutes.
-67
Download from Www.Somanuals.com. All Manuals Search And Download.
For SHARP Assistance
If you encounter any problems during setup or operation of this projector, first refer to the
“Troubleshooting” section on pages 66 and 67. If this operation manual does not answer
your question, please contact the SHARP Service departments listed below.
U.S.A.
Sharp Electronics Corporation
1-888-GO-SHARP (1-888-467-4277)
Benelux
SHARP Electronics Benelux BV
0900-SHARPCE (0900-7427723)
Nederland
9900-0159 Belgium
Canada
Mexico
Sharp Electronics of Canada Ltd.
(905) 568-7140
Australia
Sharp Corporation of Australia
Pty. Ltd.
1300-135-022
Sharp Electronics Corporation Mexico
Branch
(525) 716-9000
New Zealand
Singapore
Hong Kong
Taiwan
Sharp Corporation of New Zealand
Phone: (09) 573-0111
Fax: (09) 573-0112
Latin America Sharp Electronics Corp. Latin American
Group
(305) 264-2277
Sharp-Roxy Sales (S) Pte. Ltd.
65-226-6556
Germany
U.K.
Sharp Electronics (Europe) GMBH
01805-234675
Sharp-Roxy (HK) Ltd.
(852) 2410-2623
Sharp Electronics (U.K.) Ltd.
08705 274277
Italy
Sharp Electronics (Italy) S.P.A.
(39) 02-89595-1
Sharp Corporation (Taiwan)
0800-025111
France
Sharp Electronics France
01 49 90 35 40
Malaysia
U.A.E.
Sharp-Roxy Sales & Service Co.
(60) 3-5125678
Sharp Middle East Fze
971-4-81-5311
Spain
Sharp Electronica Espana, S.A.
93 5819700
Thailand
Korea
Sharp Thebnakorn Co. Ltd.
02-236-0170
Switzerland
Sweden
Austria
Sharp Electronics (Schweiz) AG
0041 1 846 63 11
Sharp Electronics Incorporated of
Korea
(82) 2-3660-2002
Sharp Electronics ( Nordic ) AB
(46) 8 6343600
India
Sharp Business Systems (India)
Limited
(91) 11- 6431313
Sharp Electronics (Europe) GMBH
Branch Office Austria
0043 1 727 19 123
-68
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Model
XG-C455W/PG-C355W
Display devices
Resolution
0.74" LCD panel × 3
WXGA (1280 × 800)
F number
Lens
F 1.7 – 1.9
Zoom
Manual, ×1.2 (f = 28.0 – 33.6 mm)
Focus
Manual
DVI-D (Compatible with HDCP)
Input terminals
×1
Computer/Component
(mini D-sub 15 pin)
×2
S-Video (mini DIN 4 pin)
Video (RCA)
×1
×1
Audio (ø3.5 mm stereo minijack)
Audio (RCA)
×2
×2 (L/R)
×1
Computer/Component
(mini D-sub 15 pin)
Output terminals
Audio (ø3.5 mm stereo minijack)
LAN (RJ-45)
×1 (variable audio output)
Control and
communication
terminals
×1
×1
×1
×1
USB (Type B)
RS-232C (mini DIN 9 pin)
Wired Remote
(ø3.5 mm stereo minijack)
Speakers
2 W (Mono)
Projection lamp
Rated voltage
Rated frequency
Input current
275 W
AC 100 – 240 V
50/60 Hz
3.6 A
Power consumption (Standby)
360 W (3.4 W) with AC 100 V
345 W (4.4 W) with AC 240 V
41°F to 95°F (+5°C to +35°C)
Plastic
Operation temperature
Cabinet
Dimensions (main body only) [W × H × D]
12 27/32" × 4" × 11 1/64"
(326 × 101.5 × 279.5 mm)
10.8 lbs. (4.9 kg)
Weight (approx.)
As a part of policy of continuous improvement, SHARP reserves the right to make design
and specification changes for product improvement without prior notice. The performance
specification figures indicated are nominal values of production units. There may be some
deviations from these values in individual units.
-69
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
2D Progressive ......................................................... 46
3D Progressive ......................................................... 46
Menu Position ...........................................................50
MNR ..........................................................................46
Monitor Output .......................................................... 51
MONITOR output terminal........................................28
MOUSE/Adjustment buttons ..............................39, 43
Movie ........................................................................45
AC socket ................................................................. 30
Adjustment buttons ................................................... 43
All Reset ...................................................................53
Area Zoom ................................................................ 38
Aspect ratio .........................................................37, 38
AUDIO input terminal ......................................... 23-26
Audio Output ............................................................. 51
AUDIO output terminal ............................................. 29
Auto V-Keystone .................................................32, 49
Auto Power Off ......................................................... 51
Auto Restart .............................................................. 51
Auto Sync (Auto Sync adjustment) .......................... 47
AUTO SYNC button .................................................. 35
AV MUTE button ....................................................... 34
Network ...............................................................42, 54
Normal ................................................................37, 38
ON button .................................................................30
Optional accessories ................................................10
OSD Display .............................................................50
PAGE Up/Down buttons ........................................... 39
Password ..................................................................54
PDF ............................................................................. 6
Phase ........................................................................47
Picture .................................................................40, 45
Picture Mode.............................................................45
PICTURE MODE button ........................................... 36
Power cord................................................................30
Power indicator ...................................................30, 59
Presentation..............................................................45
PRJ-ADJ .............................................................42, 51
PRJ mode .................................................................50
Progressive ...............................................................46
Projector ...................................................................55
Background............................................................... 50
Blue ...........................................................................45
Bright......................................................................... 45
Clock ......................................................................... 47
CLR Temp (Color Temperature) ............................... 45
Color ......................................................................... 45
COMPUTER/COMPONENT 1 input terminal ....23, 25
COMPUTER/COMPONENT 2 input terminal ....23, 25
Contrast .................................................................... 45
R-CLICK/RETURN button ..................................39, 43
Red ...........................................................................45
Remote control .........................................................14
Remote control sensor ............................................. 15
Remote receiver ....................................................... 39
Replacing the lamp ................................................... 61
Reset.........................................................................45
Resize .......................................................................49
RESIZE button .......................................................... 37
Resolution .................................................................47
RGB cable ................................................................23
RS-232C ...................................................................52
RS-232C terminal .....................................................27
DHCP Client ............................................................. 55
DIN-D-sub RS-232C adaptor ................................... 27
DNR ..........................................................................46
Dot By Dot ................................................................ 37
Dynamic Range ........................................................ 48
DVI-D input terminal ...........................................24, 25
ECO+QUIET button .................................................. 35
Eco+Quiet Mode ....................................................... 46
ENTER button...........................................................44
Exhaust vent .......................................................13, 56
Fan Mode..................................................................52
Film Mode ................................................................. 46
FREEZE button ........................................................ 35
Full ............................................................................ 37
SCR-ADJ ............................................................41, 49
Sharp ........................................................................45
SIG-ADJ..............................................................41, 47
Signal Info .................................................................48
Signal Type ...............................................................47
Speaker .................................................................... 51
sRGB ........................................................................45
Standard ...................................................................45
STANDBY button ......................................................30
Storage case.............................................................64
Stretch ................................................................37, 38
Subnet Mask .............................................................55
Supplied accessories ............................................... 10
S-VIDEO input terminal ............................................ 26
System Lock .............................................................52
System Sound .......................................................... 51
Game ........................................................................45
Gateway.................................................................... 55
Height Adjustment button ......................................... 31
H-Pos ........................................................................47
Image Shift................................................................ 49
INPUT buttons .......................................................... 34
Intake vent ..........................................................13, 56
IP Address ................................................................ 55
Kensington Security Standard connector ................ 13
Keycode .................................................................... 52
Keylock ..................................................................... 53
KEYSTONE button ................................................... 32
Keystone Correction ...........................................32, 49
TCP/IP ......................................................................55
Temperature warning indicator .................................59
Tilt dial.......................................................................31
Tint ............................................................................45
Lamp ......................................................................... 61
Lamp indicator ....................................................30, 59
Lamp Timer (Life) ..................................................... 53
LAN terminal ............................................................. 28
Language (on-screen display language).................. 50
LAN/RS232C ............................................................ 51
L-CLICK button ......................................................... 39
Lens cap ...................................................................12
Lens cap strap .......................................................... 10
USB terminal.............................................................39
VIDEO input terminal................................................26
Video System............................................................ 48
Volume buttons .........................................................34
V-Pos ........................................................................47
V-Stretch ...................................................................38
MAC Address ............................................................ 55
MAGNIFY buttons .................................................... 36
MENU button ............................................................ 43
WIRED REMOTE terminal ....................................... 14
-70
Download from Www.Somanuals.com. All Manuals Search And Download.
SHARP CORPORATION
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Sentry Industries Thermometer Sentry Xpress 40 User Manual
Sharp Car Video System PN K322B PN K322BH LLS201A User Manual
Sony Blu ray Player 4 145 650 111 User Manual
Sony Car Stereo System XR M510 User Manual
Sony Home Theater System DX250 User Manual
Speco Technologies Security Camera HT650PT10X User Manual
StarTechcom Security Camera IDE4044 User Manual
StreamLight Stereo System MS2015 User Manual
Sunbeam Hot Tub FB3500 User Manual
SUPER MICRO Computer Computer Hardware X6DH3 G2 User Manual