VCR/DVD COMBINATION
MODEL
DV-NC70W
DV-NC70
DV-NC70X
OPERATION MANUAL
GB
C
GB
C
ENGLISH ......
......
1 –
1 –
104
104
OPERATE EJECT/STOP
REW PLAY/×2
PLAY
STOP
OPEN/CLOSE
REC
/
TIMER
VCR/DVD
SELECTOR
CH
VCR DVD
(
L
)- -
MONO AUDIO R
AV
2
IN VIDEO
• This Operation Manual explains operation for three models (DV-NC70W, DV-NC70 and DV-NC70X)
available in the two geographic areas listed below. Take care to make sure that the instructions you
read are for your particular area.
1. DV-NC70W, DV-NC70 .... Hong Kong: Region Number 3
2. DV-NC70X ....................... Australia: Region Number 4
Only for DV-NC70W
PAL NTSC
3
4
NTSC/PAL
Download from Www.Somanuals.com. All Manuals Search And Download.
DV-NC70X
DV-NC70W
DV-NC70
About This Manual
• All mentions of “the Remote” refer to the remote control unit.
• The following table describes the icons used in this Operation Manual.
Icon
Meaning
Tips and Hints for easier operation
Functions for DVD
DVD
Functions for VIDEO CD
Functions for Audio CD
VIDEO
C D
C D
GENERAL INFORMATION
CONNECTION AND INITIAL SETTING
VCR, DVD SETUP
WATCHING THE VCR, DVD
OTHER INFORMATION
Important!
Be sure to read this Operation Manual carefully before using the Product for the first time, and keep it on hand
for future reference when you experience operational problems.
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
• This Product is classified as a CLASS 1 LASER
product.
• The CLASS 1 LASER PRODUCT label is located
on the rear cover.
• This product contains a low power laser device.
To ensure continued safety do not remove any
cover or attempt to gain access to the inside of
the product. Refer all servicing to qualified
personnel.
<Only for DV-NC70W/70>
Note:
This Product can be used only where the power
supply is AC 110V-240V, 50/60Hz. It cannot be
used elsewhere.
<Only for DV-NC70X>
Note:
This Product can be used only where the power
supply is AC 240V, 50Hz. It cannot be used
elsewhere.
CLASS 1
LASER PRODUCT
CAUTION:
USE OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN MAY RESULT
IN HAZARDOUS RADIATION EXPOSURE.
AS THE LASER BEAM USED IN THIS PRODUCT
IS HARMFUL TO THE EYES, DO NOT ATTEMPT
TO DISASSEMBLE THE CABINET. REFER
(Rear of product)
SERVICING TO QUALIFIED PERSONNEL ONLY.
WARNING:
CAUTION-LASER RADIATION WHEN OPEN. DO NOT STARE INTO BEAM
OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS.
VORSICHT-LASERSTRAHLUNG, WENN GEFFNET. BLICKEN SIE NICHT IN DEN STRAHL
UND BETRACHTEN SIE DIESEN NICHT DIREKT MIT OPTISCHEN INSTRUMENTEN.
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO
RAIN OR MOISTURE.
ATTENTION-RADIATION LASER EN CAS D'OUVERTURE. NE PAS FIXER LE
FAISCEAU NI REGARDER DIRECTEMENT DES INSTRUMENTS OPTIQUES.
VARNING-LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD. STIRRA EJ IN
I STRÅLEN OCH BETRAKTA EJ STRÅLEN MED OPTISKA INSTRUMENT.
SA005WJ
VARO ! AVATTAESSA OLET ALTTIINA LASERSÄTEILYLLE. ÄLÄ TUIJOTA
SÄTEESEEN ÄLÄKÄ KATSO SITÄ OPTISEN LAITTEEN LAPI.
VARNING-LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD. STIRRA EJ IN I
STRÅLEN OCH BETRAKTA EJ STRÅLEN GEMON OPTISKT INSTRUMENT.
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, AND ANNOYING INTERFERENCE, USE
THE RECOMMENDED ACCESSORIES ONLY.
ADVARSEL-LASERSTRÅLING NÅR DEKSEL ÅPNES. STIRR IKKE INN I
STRÅLEN ELLER SE DIREKTE MED OPTISKE INSTRUMENTER.
ADVARSEL-LASERSTRÅLING VED ÅBNING. SE IKKE IND I STRÅLEN-
HELLER IKKE MED OPTISKE INSTRUMENTER.
Laser Diode Properties
Material: AlGaInP
Wave length: 650 nm
Emission Duration: Continuous
Laser output: Max. 0.7 mW
Power Cord Protection
To avoid any malfunctions of the Product, and to
protect against electric shock, fire or personal injury,
please observe the following.
• Hold the plug firmly when connecting or
disconnecting the AC power cord.
• Keep the AC power cord away from heating
appliances.
• Never put any heavy object on the AC power cord.
• Do not attempt to repair or reconstruct the AC
power cord in any way.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
1
SAFETY INFORMATION
Location and Handling
• Do not place your Product in closed spaces or do
not cover it to prevent excessive temperatures
inside the Product.
• Do not place the Product in direct sunlight, or near
heat sources.
If There is Noise Interference on the
TV While a Broadcast is being
Received
Depending on the reception condition of the TV,
interference may appear on the TV monitor when you
watch a TV broadcast while the Product is turned on.
This is not a malfunction of the Product or the TV. To
watch a TV broadcast, turn off the Product.
• Keep the Product away from strong magnetic
objects.
• Do not place any object containing water or other
liquids on the Product. In the event that liquid
should enter the cabinet, unplug the Product
immediately and contact the retailer or service
centre approved by SHARP immediately.
• Do not remove the Product cabinet. Touching parts
inside the cabinet could result in electric shock and/
or damage to the Product. For service and adjust-
ment inside the cabinet, call a qualified dealer or
service centre approved by SHARP.
Service
Do not attempt to service this Product yourself.
Please refer any service to the nearest service centre
approved by SHARP.
Copyright
Audio-visual material may consist of copyrighted
works which must not be recorded without the
authority of the owner of the copyright. Please refer to
relevant laws in your country.
Nonuse Periods
When the Product is not being used, switch the
Product to the standby mode.
When left unused for a long period of time, the
Product should be unplugged from the household AC
outlet.
Copy Protection
This Product supports Macrovision copy protection.
On DVDs that include a copy protection code, if the
contents of the DVD are copied using a VCR, the
copy protection code prevents the videotape copy
from playing normally.
No Fingers or Other Objects Inside
Do not put any foreign object on the disc tray.
Apparatus Claims of U.S.Patent Nos. 4,631,603,
4,577,216, 4,819,098 and 4,907,093 licensed for
limited viewing uses only.
Stacking
Place the Product in a horizontal position, and do not
place anything heavy on it.
This product incorporates copyright protection
technology that is protected by method claims of
certain U.S. patents and other intellectual property
rights owned by Macrovision Corporation and
other rights owners. Use of this copyright
protection technology must be authorized by
Macrovision Corporation, and is intended for home
and other limited viewing uses only unless
Condensation
Moisture may form on the pickup lens in the following
conditions:
• immediately after a heater has been turned on.
• in a steamy or very humid room.
• when the Product is suddenly moved from a cold
environment to a warm one.
otherwise authorized by Macrovision Corporation.
Reverse engineering or disassembly is prohibited.
If moisture forms inside this Product, it may not
operate properly.
In this case, turn on the power and wait about one
hour for the moisture to evaporate.
Recommended Measures for
Optimum Picture Excellence
The Product is a precision device that is constructed
using extremely accurate technology.
Cleaning
Unplug your Product before cleaning. Use a damp
cloth for cleaning. Do not use cleaning fluids or
aerosols which could enter the Product and cause
damage, fire, or electrical shock. These substances
may also deteriorate the finish of your Product.
Soiling or friction affecting the pickup lens or disc
drive can impair the image quality. At the worst,
neither video nor audio will be played back. To obtain
optimum picture quality, the Product should be
checked (cleaning and replacement of some parts)
every 1,000 hours. Note that this period varies
depending on the environment (temperature, humid-
ity, dust, etc.) in which the Product is used. Contact
your authorized Sharp supplier for details.
Do not attempt to clean the pickup lens yourself.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Types of Discs that Can Be Played on This Product
This Product can play back discs bearing any of the following marks:
DVD
See
See
1
DVD-R/DVD-RW*
[8cm(3") disc/12cm(5") disc]
2 on the next page
* Disks that have not been finalized cannot be played
back. In addition, disks that have been recorded
with the video recording format (VR Recording) also
cannot be played back.
4.7
VIDEO CDs
[8cm(3") disc/12cm(5") disc]
• Supports up to version 2.0.
Audio CDs
See
3 on the next page
[8cm(3") disc/12cm(5") disc]
CD-R/CD-RW
[8cm(3") disc/12cm(5") disc]
• Discs recorded in MP3 file format or
Audio format.
Other CDs
1) On CD-G and CD-EXTRA discs, only the sound can be played (no images).
2) Photo CD, DVD-ROM, DVD-RW (Video Recording Format), DVD-Audio, SACD, SVCD and CD-ROM
discs cannot be used.
3) Discs with unusual shapes (heart-shaped or hexagonal discs) cannot be used. The use of such discs will
cause a fault.
• This Product will reject an incompatible disc, therefore the disc type should be checked.
This Product will output NTSC signals when playing “NTSC discs”.
NTSC signals cannot be converted to modified PAL signals.
An NTSC TV or NTSC-compatible Multi-system TV must be used when playing NTSC discs.
DVD-R/DVD-RW Recording Modes
The video mode refers to a mode that allows playback with an ordinary DVD player. It is the mode that allows
recording onto disks of DVD-R Ver. 2.0 or later or DVD-RW Ver. 1.1 or later. The video recording format (VR
Recording) refers to the recording mode that allows various recording functions and editing in compliance with
the standard specifications of the DVD Forum. (Cannot be played back with this Product)
1
•
DVD video players and discs are designed with region numbers which dictate the regions in which a disc can be played. If the region
number on the disc you want to play does not match the region number in this Product, you will not be able to play the disc.
<Only for DV-NC70W, DV-NC70>
Samples of region number marks compatible
with this Player:
The region number for
this Player is 3.
1
1 23
4 56
....
........
3
ALL
3
13
6
Disc playable in all regions
<Only for DV-NC70X>
Samples of region number marks compatible
with this Player:
The region number for
this Player is 4.
1
1 23
4 56
....
........
4
ALL
4
14
6
Disc playable in all regions
As for the list of the region number 3, 4 countries and the world map for all region numbers, refer to pages 102 and 103.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Types of Discs that Can Be Played on This Product
Disc Function or Operation that is Not Available
In the cases listed below, the or indicator may appear on the TV screen, which indicates
that the function or operation is not available.
• When you intend to perform the function or operation on which the manufacturer restriction is imposed:
The specific functions on some DVDs and VIDEO CDs are determined by the disc manufacturer. As this
Product plays disc data in accordance with the guidelines of the disc manufacturer, some functions may
not be available on some discs. Be sure to read the documentation provided with the disc.
• When you intend to perform the functions or operations prohibited for the current disc:
The types of functions and operations that can be used for a particular disc vary depending on the
features of that disc. Some disc functions and operations may differ from the descriptions given in this
Operation Manual. In this event, follow the instructions given on the screen.
Icons Used on DVDs
Sample Icons
1. English
2. Chinese
1. English
2. Chinese
2
16:9 LB
2
3
2
Number of audio
tracks
Type of subtitles Screen aspect
recorded ratio recorded
Disc with
multiple
Region code indicator
camera angles
2
• This Product supports 2-channel (L/R) audio and 5.1ch (Multi-channel) MPEG Audio 1/2 (only when the DIGITAL OUT coaxial
jack is used for connection). It does not support 7.1 channel MPEG Audio Version 2.0.
3
• When playing back a CD-G (Graphics) or CD EXTRA disc, the audio portion will be played, but the graphic images will not
be shown.
Title, Chapter and Tracks
• DVDs are divided into “titles” and “chapters”. If the disc has more than one movie on it, each movie would be
a separate “title”. “Chapters”, on the other hand, are sections of titles.
Example: DVD
Title 1
Title 2
Chapter 1
Chapter 2
Chapter 3
Chapter 1
Chapter 2
• VIDEO CDs and Audio CDs are divided into “tracks”. You can think of a “track” as one tune on an Audio CD.
Example: VIDEO CD or Audio CD
Track 1
Track 2
Track 3
Track 4
Track 5
• Numbers identify each title, chapter, and track on a disc. Most discs have these numbers recorded on them, but some do
not.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Disc Handling and Maintenance
Handling Precautions
• Hold the disc by the edges so the surface will not be soiled with
A
fingerprints. (
)
A
Fingerprints, dirt and scratches can cause skipping and distortion.
• Do not write on the label side with a ball-point pen or other writing
utensils.
• Do not use record cleaning sprays, benzine, thinner, static electricity
prevention liquids or any other solvent.
• Be careful not to drop or bend the disc.
• Do not install more than 1 disc on the disc tray.
• Do not try to close the disc tray when the disc is not installed
properly. (
)
B
• Be sure to store the disc in its exclusive case when not in use.
Then store upright.
• Do not stick paper or adhesive labels to the disc.
B
C
If the Surface is Soiled ( )
Wipe gently with a soft, damp (water only) cloth.
When wiping discs, always move the cloth from the center hole
towards the outer edge.
(If you wipe the discs using a circular motion, circular scratches are
likely to occur, which will cause noise.)
If the playing surface of a disc is soiled or scratched, the Product
may decide that the disc is incompatible and eject the disc tray,
or it may fail to play the disc correctly. Wipe any soiling off the
playing surface with a soft cloth.
Disc tray
Disc
C
If the Disc is Brought from a Cold to a Warm
Environment, Dew May Form on the Disc
Wipe the dew off with a soft, dry, lint-free cloth before using the disc.
Improper Disc Storage
You can damage discs if you store them in the following places:
• Areas exposed to direct sunlight
• Humid or dusty areas
• Areas directly exposed to a heat outlet or heating appliance
Maintenance
• Be sure to turn the Product off and disconnect the AC power cord
before maintaining the Product.
• Wipe this Product with a dry soft cloth.
If the surfaces are extremely dirty, wipe clean with a cloth which
has been dipped in a weak soap-and-water solution and wrung
out thoroughly and then wipe again with a dry cloth.
• Never use alcohol, benzine, thinner, cleaning fluid or other
chemicals. And do not use compressed air to remove dust.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Contents
VCR Display Information ............................ 38
How to Display Indicators .................................38
VCR Front Panel Display .................................38
GENERAL INFORMATION
SAFETY INFORMATION ................................ 1
Types of Discs that Can Be Played on
This Product .............................................. 3
DVD SETUP
Disc Handling and Maintenance .................. 5
Features ......................................................... 8
Accessories ................................................... 8
Major Components........................................ 9
DVD Setup.................................................... 40
About the SETUP Screen.................................40
TV MODE Setting .............................................41
PARENTAL Level Setting .................................42
AUDIO Setting ..................................................44
Setting the COMPRESSION
CONNECTION AND INITIAL SETTINGS
(Dolby Digital output level) ..........................44
Setting the DOLBY DIGITAL .........................45
Setting the MPEG .........................................46
Basic Connection ........................................ 14
Connecting to ANTENNA IN/RF OUT ..............14
Setting the CINEMA VOICE ..........................46
DISC LANGUAGE Setting................................47
Setting SUBTITLE,
Connecting a TV Equipped with
VIDEO/AUDIO Input Jacks ..........................15
Using the Component Colour (Y, PB (CB),
AUDIO and MENU languages ....................47
and PR (CR)) Output Jacks ...........................15
Selecting languages from OTHER ................48
DVD Audio Connections ............................. 16
DVD Display Information ............................ 49
Connecting a TV Equipped with S-VIDEO
Operation Mode Indicators ...............................49
Input Jacks ...................................................16
Connecting to Audio Equipment .......................16
Playing 2 channel audio ................................16
Language Code List for Disc Language ... 50
Playing Dolby Digital (5.1 channel), DTS or
MPEG audio ...............................................17
WATCHING THE VCR
Preparations Before Using the Product.... 18
Adjusting the Video Channel ..................... 19
Auto Tuning System ................................... 21
Playback....................................................... 52
Inserting a Video Cassette ...............................52
Playback ...........................................................52
Video Search (with the Remote).......................52
Fast Forwarding and Rewinding.......................53
Slow Motion Playback (with the Remote) .........53
Still Picture and Frame Advance ......................53
Double Speed Playback ...................................53
NTSC Tape Play Back on PAL TV ....................54
Full Auto Playback ............................................54
Auto Head Cleaning System ............................54
Auto Tracking Control System ..........................54
Quick Start with Full Loading Mechanism ........54
AUTO RENTAL.................................................55
COLOUR ..........................................................55
BLUE BACK .....................................................56
Playback of Hi-Fi Recorded Tapes ...................57
Audio Output Mode ..........................................57
Adjusting Hi-Fi Audio Tracking .........................57
VCR SETUP
VCR Setup.................................................... 24
Menu Screen ....................................................24
Mode Selection.................................................25
Setting the Channels ........................................27
Auto Tuning ......................................................28
Manual Tuning ..................................................30
Channel Skip/Cancelling Skip ..........................32
Channel Skip.................................................32
Cancelling Skip .............................................34
Setting the Clock ..............................................35
Initial Setting of Clock ...................................35
Changing the Clock Setting ..........................36
Setting the Language .......................................37
VCR-RESET .................................................37
Initial Setting of Language ............................37
Changing Language......................................37
Sharp Super Picture.................................... 58
Auto Repeat ................................................. 59
Auto Zero Back............................................ 60
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Contents
DPSS (Digital Program Search System)
/Skip Search ............................................ 61
DPSS................................................................61
Skip Search ......................................................61
About the Function Control Screen .......... 85
Direct skip (title [track]/chapter/time) ................86
Subtitle language setting ..................................87
Angle setting.....................................................88
Audio setting.....................................................89
3D VIRTUAL SURROUND setting ...................90
DIGITAL GAMMA setting ..................................91
TV Programme Recording.......................... 62
Cassette Erase Protection................................62
Recording a TV Programme .............................62
To Watch Another TV Programme While
Direct Selection of Scenes ......................... 92
Selecting Scenes by Title Number ...................92
Selecting Scenes from the Menu Screen .........92
Recording.....................................................62
Recording NICAM/IGR Multiplex Broadcasts ...63
Simple Recording Timer ............................. 64
Programmed Playback ............................... 93
Chapter Programmed Playback .......................93
Track Programmed Playback ...........................94
MP3 Files Programmed Playback ....................95
Immediate Recording .......................................64
Programming the Timer with G-CODE® System
(DV-NC70W only)..................................... 65
Setting the Programme Number In Step 4 .......67
Repeat Playback.......................................... 96
Repeat playback...............................................96
A-B Repeat .......................................................97
Recording with the Timer ........................... 68
Confirming Timer Programmes ........................71
Cancelling Timer Programmes .........................72
Resume Function ........................................ 98
Tape Dubbing .............................................. 73
Recording a DVD Disc onto a Video
OTHER INFORMATION
Cassette ................................................... 74
Recording a DVD disc onto a Video cassette
(Tape Editing mode).....................................74
Troubleshooting .......................................... 99
Definition of Terms.................................... 101
Specifications............................................ 104
WATCHING THE DVD
Preparing to Use DVD ................................. 78
When connecting a TV with the
DVD output jacks .........................................78
When connecting a TV with the
DVD/VCR shared output jacks ....................78
Playback....................................................... 79
Basic Play.........................................................79
Track Direct Playback.......................................79
Fast Forward/Fast Reverse ..............................80
Slow-Motion Play..............................................80
Still/Pause ........................................................81
Frame Advance ................................................81
Skip (Forward/Reverse) ...................................81
Angle Selection ........................................... 82
Playing MP3 Discs ...................................... 83
Regarding MP3 discs .......................................83
Playing MP3 discs ............................................83
To play MP3 discs ............................................84
To play another file (music title) while playing ..84
To skip the file while playing .............................84
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Features
■ Common Features
• A DVD, AUDIO CD, VIDEO CD player and VCR all in one.
• Simultaneous VCR recording and DVD playback.
■ VCR
•
Hi-Fi Stereo Sound, NICAM/IGR System
• 380-times High Speed Rewind Function (in NTSC)
• S-VHS Simple Playback
• HQ (High Quality) Circuitry
• Simple Recording Timer
• Sharp Super Picture
• G-CODE System*............... only for DV-NC70W
* For Hong Kong: G-CODE is a registered trademark of Gemstar Development Corporation. The G-CODE system is
manufactured under license from Gemstar Development Corporation.
■ DVD
• Plays DVD, VIDEO CD and Audio CD discs as well as CD-R/CD-RW discs recorded in MP3 file format
• 3D Virtual Surround provides high-quality surround sound
• Digital Gamma correction
• Dolby Digital*1, DTS*2, MPEG Audio digital out capability
• High-quality digital images
• High-quality digital sound
*1 Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of
Dolby Laboratories.
*2 “DTS” and “DTS Digital Surround” are trademarks of Digital Theater Systems, Inc.
Disc Features and this Operation Manual
• The types of functions and operations that can be used for a particular disc vary depending on the
features of that disc. In some cases, these functions and operations may differ from the descriptions given
in this Operation Manual. In this event, follow the instructions given on the screen. This Operation Manual
only covers basic disc operations.
• For some operations, the
or
indicator may appear on the TV screen. This indicates that
the operation described in this Operation Manual is not permitted for the current disc.
Accessories
G-CODE
DV- NC70W
PROG
DV- NC70
DV- NC70X
TIMER
OPERATE
ON/OFF
EJECT
ON
VCR/DVD VCR MENU
DISPLAY SCREEN SELECTOR DVD SETUP
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
TITLE
DVD MENU
Two batteries
(AA, R6 or UM/SUM-3 )
for the Remote
CLEAR
SET
RETURN
ENTER
ZERO BACK
VIDEO/AUDIO cable
SKIP SEARCH
AM/PM
INPUT SELECT VCR DVD
/
REV
FWD
PLAY
REC
PAUSE/STILL
STOP
TAPE
SPEED
DPSS
SKIP
SLOW
AUDIO
OUTPUT
CH
VCR
DVD
VCR/DVD COMBINATION
Remote control unit
RF cable
Operation Manual
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Major Components
VCR Main Unit (Front)
Numbers in
refer to the main pages
in this Operation Manual where the topic is explained.
Cassette compartment
VCR/DVD SELECTOR
TIMER indicator
52
18
70
18 OPERATE
EJECT/STOP
52
OPERATE EJECT/STOP
REW
PLAY/×2
PLAY
STOP
OPEN/CLOSE
Front AUDIO/
VIDEO input
REC
/
TIMER
VCR/DVD
SELECTOR
CH
VCR DVD
(
L
)- -
MONO AUDIO R
AV
2
IN VIDEO
73
jack
52
REW
PLAY/×2 52
62
38
REC
CH
VCR Front Panel Display
Operation status
38
Indicator
Timer Recording
Indicator
67
57
62
VCR
L R
Audio Output
Indicator
SEPVP D
Tape Speeds
Indicator
38
38
38
Clock Indicator
Channel Indicator
Tape Counter Indicator
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
9
Major Components
DVD Main Unit (Front)
Numbers in
refer to the main pages
in this Operation Manual where the topic is explained.
Disc tray
79
79
OPERATE 78
OPEN/CLOSE
OPERATE EJECT/STOP
REW
PLAY/×2
PLAY
STOP
OPEN/CLOSE
REC
/
TIMER
VCR/DVD
SELECTOR
CH
VCR DVD
(
L
)- -
MONO AUDIO R
AV
2
IN VIDEO
79
75
Disc operation
buttons (PLAY, STOP)
VCR/DVD SELECTOR
78
VCR DVD Indicator
DVD Front Panel Display
TITLE
Indicator
1
TRACK
Indicator
PROGRAM Indicator
95
CHAPTER
Indicator
VIRTUAL surround
Indicator
90
Operation status/Time Indicator
49
REPEAT Indicator
ANGLE Indicator
96
82
2
You can toggle between 1 and 2 by
pressing the remote control unit’s
DISPLAY button (page 49).
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
10
Major Components
Remote (VCR Operation Buttons)
• The explanations on this page use the VCR/DVD CHANGE Switch in the VCR position.
Numbers in
refer to the main pages
in this Operation Manual where the topic is explained.
G-CODE
DV- NC70W
65
PROG
DV- NC70
DV- NC70X
67
18
38
38
20
60
TIMER ON/OFF
OPERATE
68
52
19
78
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
EJECT
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
VCR MENU
DISPLAY
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
VCR/DVD SELECTOR
ON SCREEN
TITLE
DVD MENU
CURSOR (
/
/
/
)
CLEAR
RETURN
SET
ENTER
20
60
61
SET
CLEAR
ZERO BACK
ZERO BACK
SKIP SEARCH
SKIP SEARCH
32
Number buttons
AM/PM
INPUT SELECT VCR DVD
/
/
36
52
AM/PM or
73
62
52
VCR DVD
INPUT SELECT
FF
REV
FWD
REW
PLAY
52
62
52
62
38
PLAY
REC
REC
PAUSE/STILL
STOP
53
53
53
57
PAUSE/ STILL
STOP
TAPE
SPEED
DPSS
SKIP
—
/
—
/
61
SLOW
SLOW
,
DPSS
TAPE SPEED
AUDIO
OUTPUT
CH
SLOW
AUDIO OUTPUT
CH
/
VCR
DVD
18
VCR/DVD CHANGE Switch
VCR/DVD COMBINATION
Loading the Batteries
1
Open the battery cover
by pulling the lid in the
direction of the arrow.
2
Load the batteries.
Load the two batteries (AA, R6 or UM/SUM-3)
supplied with the Remote so that the battery
3
Close the battery cover
by lowering the lid in the
direction of the arrow.
poles
and
are positioned as indicated.
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
11
Major Components
Remote (DVD Operation Buttons)
• The explanations on this page use the VCR/DVD CHANGE Switch in the DVD position.
Numbers in
refer to the main pages
in this Operation Manual where the topic is explained.
93
96
79
PROG
, REPEAT
OPERATE
18
82
VCR/DVD SELECTOR
ANGLE
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
49
49
ON SCREEN
DISPLAY
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
41
79
92
DVD SETUP
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
85
FUNCTION CONTROL
OPEN/CLOSE
DVD MENU
TITLE
DVD MENU
TITLE 92
CLEAR
RETURN
SET
ENTER
41
41
RETURN
ENTER
ZERO BACK
42 CURSOR (
/
/
/
)
SKIP SEARCH
42
Number buttons
AM/PM
INPUT SELECT VCR DVD
/
79
PLAY
FWD
REV
FWD
80
79
PLAY
REV
80
80
REC
PAUSE/STILL
STOP
STOP
PAUSE/STILL
TAPE
SPEED
DPSS
SKIP
SLOW
80
81
SLOW
SKIP
AUDIO
OUTPUT
CH
VCR
DVD
18
VCR/DVD CHANGE Switch
VCR/DVD COMBINATION
• Do not subject the Remote to shock, water or excessive humidity.
• The Remote may not function if the Product sensor is in direct sunlight or any other strong light.
• Incorrect use of batteries may cause them to leak or burst. Read the battery warnings and use the batteries properly.
• Do not mix old and new batteries, or mix brands in use.
• Remove the batteries if you do not use the Remote for an extended period of time.
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
12
Major Components
Main Unit (Rear)
D OT
DVD/VCR
VCR
ANTENNA IN
LINE OUT
1
LINE IN
1
COMPONENT
R
R
AUDIO
L
AUDIO
L
RF OUT
VIDEO
VIDEO
To an AC outlet
15
DVD/VCR shared
AUDIO output jacks
VCR AUDIO input
jacks
DVD Coaxial DIGITAL 17
ANTENNA IN (antena
or cable input)
14
output jack
DVD/VCR
VCR
ANTENNA IN
RF OUT
LINE OUT 1 LINE IN 1
COMPONENT
R
R
AUDIO
L
AUDIO
L
VIDEO
VIDEO
COMPONENT VIDEO output jacks 15
14 ANTENNA OUT
VCR VIDEO input
jack
DVD S-VIDEO output jack 16
DVD AUDIO output jacks 16
15
DVD/VCR shared
VIDEO output jack
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
13
Basic Connection
Caution:
• Be sure to turn off the Product and equipment to be connected before connecting.
• Read through the operation manual for the equipment to be connected.
•
Be sure that the colours of the jacks and plugs match up when using a VIDEO/AUDIO cable.
• Be sure to keep the Product connection cables separate from the TV antenna cable when you install the
Product, because it may cause electrical interference when you are watching television programmes.
Connecting to ANTENNA IN/RF OUT
The connection method differs depending on the type of TV.
To ANTENNA
IN jack
Antenna cable
DVD/VCR
TENNA IN
LINE OUT
1
LINE IN 1
COMPONENT
R
R
AUDIO
L
AUDIO
L
RF OUT
VIDEO
VIDEO
This Product
To RF OUT jack
TV
To antenna
input jack
RF cable
(Supplied)
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
14
Basic Connection
Connecting a TV Equipped with VIDEO/AUDIO Input Jacks
This Product
DVD/VCR
VCR
ANTENNA IN
OUT
1
LINE IN 1
(Red)LINE
COMPONENT
R
R
AUDIO
L
(White)AUDIO
L
RF OUT
VIDEO
(Yellow)VIDEO
Required cable
VIDEO/AUDIO cable (supplied)
To DVD/VCR shared
VIDEO/AUDIO out jacks
VIDEO/AUDIO cable
(supplied)
Yellow
White (L)
Red (R)
Yellow
White (L)
Red (R)
To VIDEO/AUDIO
input jacks
Jack and Plug Colours
Video: Yellow
(White)
(Red)
(Yellow)
Audio Left: White
Audio Right: Red
L
R
AUDIO
IN
VIDEO
IN
TV (with external input jacks)
You will not be able to hear all of the sound being output by the Product if you use the supplied VIDEO/AUDIO
cable to a monaural TV that has only one AUDIO input jack.
• Make sure that colours of the jacks and plugs match up when connecting the cable.
• Connect the Product directly to the TV. If you attempt to view video on a TV connected via a VCR, the copy protection
function will scramble the picture.
• If you want to listen to the audio through audio equipment, connect only the VIDEO cable to the TV.
Using the Component Colour (Y, PB (CB) and PR (CR)) Output Jacks
Colour Output Jacks (Y, PB (CB)and
PR (CR)):
Some TVs and monitors are equipped with
input jacks for the component colour
signals (Y, PB (CB)and PR (CR)). By connect-
ing these input jacks to the corresponding
output jacks on the Product, you can enjoy
higher quality playback images.
DVD/VCR
VCR
ANTENNA IN
LINE OUT
1
LINE IN 1
R
R
AUDIO
L
AUDIO
L
RF OUT
VIDEO
VIDEO
If you are using a TV or monitor equipped
with Y, PB (CB) and PR (CR) jacks, use these
jacks rather than the S-VIDEO OUT jack.
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
15
DVD Audio Connections
Connecting a TV Equipped with S-VIDEO Input Jacks
When you want to achieve a better video image by connecting a TV equipped with an S-VIDEO input connector
to the Product, you should use an S-VIDEO cable (commercially available) to connect the TV to the Product.
Connecting to Audio Equipment
Connecting the Product to audio equipment provides normal stereo sound plus powerful stereo sound en-
hanced by Dolby Digital (5.1 channel), DTS, and MPEG Audio.
Playing 2 channel audio
Required cables
■ Analogue Connection
AUDIO cable (commercially available)
White (L)
White (L)
Red (R)
Red (R)
S-VIDEO cable (commercially available)
This Product
To AUDIO
VCR
ANTENNA IN
OUT jacks
INE IN 1
COMPONENT
R
R
AUDIO
L
AUDIO
L
(Red)
RF OUT
VIDEO
VIDEO
(White)
To S-VIDEO
OUT jack
S-VIDEO cable
(commercially available)
AUDIO cable
(commercially available)
Jack and Plug Colours
Audio Left: White
To amplifier
audio input jacks
Audio Right: Red
ANALOG INPUT
(White)
To S-VIDEO
input jack
L
(Red)
R
-
S VIDEO
INPUT
Amplifier of stereo system, etc.
TV (with external input jacks)
If the Product is set to OPERATE ON, the DVD signals will be output from the DVD OUT jacks at all times.
(The DVD signals will be output from the DVD OUT jacks also when using the VCR.)
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
16
DVD Audio Connections
Playing Dolby Digital (5.1 channel), DTS or MPEG audio
Connecting an amplifier with a Dolby Digital/DTS/MPEG Audio digital surround processor or a Dolby Digital/
DTS/MPEG Audio surround processor to your Product’s coaxial digital jack provides richer and more powerful
audio play.
■ Connection to a processor or amplifier with a coaxial digital input jack
Required cable
You can make this connection
Coaxial digital cable (commercially available)
using a coaxial digital cable
.
DVD/VCR
VCR
ANTENNA IN
LINE OUT
1
LINE IN 1
COMPONENT
R
R
AUDIO
L
AUDIO
L
RF OUT
VIDEO
VIDEO
To coaxial
DIGITAL OUT jack
This Product
Coaxial digital cable
(commercially available)
To coaxial
digital input jack
DIGITAL IN
COAXIAL
Audio equipment
Digital Connection to an MD to Record a CD
Some Audio CDs and VIDEO CDs have a short silent section between musical tracks. When sound from discs
such as these is digitally recorded by connecting the Product directly to a digital recorder (such as an MD player),
the music may be recorded continuously and track numbers may be lost.
■ Digital Connection to Audio Equipment or MD Player without a Dolby Digital Decoder
• Audio CD or VIDEO CD
Play the disc as you normally would, with the audio mode set to “L+R” (see page 89). With a digital
connection, audio of a disc recorded with DTS sounds abnormal in this case.
• DVD
With a digital connection, audio cannot be produced from a DVD recorded with Dolby Digital (5.1 channel),
Dolby Surround (Pro Logic), DTS or MPEG Audio, so you should use an analogue connection to play such
discs. Discs with linear PCM audio should play normally.
• This connection is not possible if the processor or amplifier to which you want to connect does not have a coaxial
digital input jack.
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
17
Preparations Before Using the Product
Preparing to Watch a VCR or a DVD
1
Turn on the TV and switch the TV channel to the external
“VIDEO” or “AV” channel connected to the DVD/VCR shared
output jacks.
OPERATE EJECT/STOP
REW PLAY/×
2
PLAY
STOP
OPEN/CLOSE
REC
/
TIMER
VCR/DVD
SELECTOR
CH
VCR DVD
(
L
)
-
AV
2
IN VIDEO
MONO AUDIO R
-
2
3
Press OPERATE.
• The product is turned on.
VCR/DVD
SELECTOR
OPERATE
VCR/DVD
SELECTOR
Press VCR/DVD SELECTOR on the remote control to switch to
the “VCR” mode or “DVD” mode.
• The VCR/DVD SELECTOR on the product lights up in orange
for “VCR” or green for “DVD”.
TIMER
TIMER
OPERATE
ON/OFF
OPERATE
ON/OFF
EJECT
VCR/DVD VCR MENU
EJECT
VCR/DVD
SELECTOR
ON
ON
VCR/DVD VCR MENU
DISPLAY SCREEN SELECTOR DVD SETUP
DISPLAY SCREEN SELECTOR DVD SETUP
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
ANGLE
TITLE
DVD MENU
TITLE
DVD MENU
• Each time VCR/DVD SELECTOR is pressed, the mode
changes between “VCR” mode and “DVD” mode.
• The mode can be switched by pressing the VCR/DVD
SELECTOR on the product.
CLEAR
RETURN
SET
CLEAR
RETURN
SET
ENTER
ENTER
ZERO BACK
ZERO BACK
SKIP SEARCH
SKIP SEARCH
AM/PM
INPUT SELECT VCR DVD
AM/PM
INPUT SELECT VCR DVD
/
/
4
Move the VCR/DVD CHANGE Switch on the Remote to either
“VCR” or “DVD”.
REV
FWD
REV
FWD
PLAY
PLAY
REC
REC
PAUSE/STILL
STOP
PAUSE/STILL
STOP
VCR
DVD
VCR
DVD
TAPE
SPEED
DPSS
SKIP
TAPE
SPEED
DPSS
SKIP
SLOW
SLOW
AUDIO
OUTPUT
AUDIO
OUTPUT
CH
CH
VCR
DVD
VCR
DVD
The VCR functions on
the Remote will now
take priority.
The DVD functions on
the Remote will now
take priority.
VCR/DVD COMBINATION
VCR/DVD COMBINATION
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
18
Adjusting the Video Channel
To view the output of your Product on the television screen, you must
select an unused channel on your TV and tune it to the output of your
Product (see Table 1 for factory preset to UHF Channel).
1
Make sure both Products (TV and this Product) are connected
(power cord) to the power outlet.
G-CODE
PROG
DV- NC70W
DV- NC70
DV- NC70X
2
3
4
Turn on your TV.
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
Select an unused channel on your TV.
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
Set the power on the Product to off. (If the Product is ON, press
OPERATE to turn off the power.)
TITLE
DVD MENU
CLEAR
RETURN
SET
ENTER
5
Keep pressing VCR MENU for more than two seconds to light up
the UHF Channel (see Table 1) on the VCR Front Panel display.
ZERO BACK
SKIP SEARCH
Table 1
Factory Preset UHF Channel
South East Asia,
60
AM/PM
INPUT SELECT VCR DVD
Hong Kong
Australia
Ex.
/
37
REV
FWD
PLAY
6
Adjust the tuning of the selected TV channel until the RF pattern
appears on your TV screen. (Refer to your Operation Manual for
tuning procedures.)
REC
PAUSE/STILL
STOP
TAPE
SPEED
DPSS
SKIP
SLOW
DV-NC70W and
DV-NC70 only
RF
SYSTEM I B/G D/K
AUDIO
OUTPUT
CH
VCR
DVD
(RF pattern)
RF
DV-NC70X only
VCR/DVD COMBINATION
SYSTEM B/G D/K
(RF pattern)
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
19
Adjusting the Video Channel
7
8
Press \/ |to select the RF output system that corresponds to
your TV by referring to the chart shown to the below, and press
SET.
I,B/G,D/K (RF system)
G-CODE
PROG
DV- NC70W
Hong Kong
I
China, Russia
D/K
DV- NC70
DV- NC70X
Ex.
South East Asia
Australia
B/G
New Zealand
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
Press OPERATE to turn on the power of the Product. Select any
channel on the VCR tuner. If a picture appears and sound can
be heard, then the RF output system is correctly set. If a picture
appears but no sound can be heard, then perform step 7 above
to select another RF output system.
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
TITLE
DVD MENU
CLEAR
RETURN
SET
ENTER
ZERO BACK
• Make sure the sound is not muted when checking the RF output
system.
SKIP SEARCH
• It is not necessary to change the system to RF system “M”. The
Product will automatically detect and change the RF system to “M”
when receiving the NTSC signal.
AM/PM
INPUT SELECT VCR DVD
• If picture interference appears on the TV screen in step 6 above, you
can change the video channel (RF output channel from the Product to
TV) with the following procedure. If UHF Channel (see Table 1) is an
active broadcast channel in your area, manually select a different
channel (UHF 21 to UHF 69) (see below) and then retune your TV as
above.
/
REV
FWD
PLAY
REC
PAUSE/STILL
STOP
1 Press OPERATE to turn off the power.
2 Keep pressing VCR MENU for more than two seconds to light up
the UHF Channel (see Table 1) on the VCR Front Panel display.
3 Press '/ "on the Remote to manually select an unused channel
for use as the video channel.
TAPE
SPEED
DPSS
SKIP
SLOW
AUDIO
OUTPUT
CH
4 Perform steps 6 to 7 above using the newly selected video
channel.
VCR
DVD
5 Repeat steps 3–4 to select the optimal video channel.
VCR/DVD COMBINATION
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
20
Auto Tuning System
G-CODE
PROG
This Product is equipped with an Auto Tuning System to provide
easier set up of the Product. After following the instructions for
“Basic Connection” on pages 14 and 15 and “Adjusting the Video
Channel” on page 19, turn on your TV, press OPERATE to turn on
the Product, and select the video channel. The Product will automati-
cally display the setting screens as shown below.
DV- NC70W
DV- NC70
DV- NC70X
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
Selection of language to be used for
LANGUAGE setting screen
the On Screen Display. (See page 37.)
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
Press SET. (Manual operation)
TITLE
DVD MENU
Selection of broadcast system(SYSTEM)
(I, B/G, D/K or M) that correspond with your
area. (See page 28, step 3.)
SYSTEM setting screen
CLEAR
RETURN
SET
ENTER
Press SET. (Manual operation)
ZERO BACK
Setting and sorting the channels for your
area. (See page 28.)
AUTOMATIC TUNING screen
SKIP SEARCH
Press VCR MENU to cancel the next step.
Setting the present time. (See page 35.)
CLOCK setting screen
Press SET. (Manual operation)
Normal screen appears.
AM/PM
INPUT SELECT VCR DVD
/
REV
FWD
PLAY
REC
PAUSE/STILL
STOP
TAPE
SPEED
DPSS
SKIP
SLOW
• If the Language selection and Auto Tuning have already been
performed, the Clock setting screen will first appear. To reset all VCR
settings and perform the Auto Tuning from the Language setting
screen, see page 37. (Perform “VCR-RESET”)
AUDIO
OUTPUT
CH
VCR
DVD
VCR/DVD COMBINATION
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
21
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
22
VCR Setup
VCR Setup .................................................................................... 24
Menu Screen............................................................................... 24
Mode Selection ........................................................................... 25
Setting the Channels................................................................... 27
Auto Tuning ................................................................................. 28
Manual Tuning ............................................................................ 30
Channel Skip/Cancelling Skip ..................................................... 32
Channel Skip............................................................................ 32
Cancelling Skip ........................................................................ 34
Setting the Clock ......................................................................... 35
Initial Setting of Clock .............................................................. 35
Changing the Clock Setting ..................................................... 36
Setting the Language .................................................................. 37
VCR-RESET ............................................................................ 37
Initial Setting of Language ....................................................... 37
Changing Language................................................................. 37
VCR Display Information ............................................................. 38
How to Display Indicators ........................................................... 38
VCR Front Panel Display ............................................................ 38
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
23
VCR Setup
Menu Screen
The menu screen is a home screen used to select various screen
functions. A sub-menu will appear once you select an item for the
menu. See the following pages for details on each menu procedure.
Menu Screen
MENU
Only for
DV-NC70W
G-CODE
TIMER
MODE
CHANNEL PRESET
CLOCK
LANGUAGE
• The word “G-CODE” will only appear on menu screen for DV-NC70W
which has the G-CODE system.
:SELECT
SET:ENTER
MENU:EXIT
MENU item list
Main Menu
Only for DV-NC70W
G-CODE
65
TIMER
68
COLOUR [AUTO/PAL/MESECAM/NTSC]
NTSC [3.58/4.43/PAL TV]
BLUE BACK [AUTO/OFF]
AUTO RENTAL [ON/OFF]
REPEAT [ON/OFF]
MODE
25
NICAM [AUTO/OFF]
S. PICTURE [ON/OFF]
AUTO
CHANNEL PRESET
28
MANUAL
PRESET CH
SYSTEM
CHANNEL
FINE TUNING
SKIP [ON/OFF]
CLOCK
35
37
ENGLISH
LANGUAGE
• Numbers in
refer to the pages where the setting
procedures are described.
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
24
VCR Setup
Mode Selection
You can set the basic functions listed in the table below on the MODE
selection screen.
G-CODE
DV- NC70W
Preparation
• Press OPERATE. Then move the VCR/DVD CHANGE Switch to
VCR.
PROG
DV- NC70
DV- NC70X
1
2
Press VCR MENU to display the menu screen.
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
Select “MODE” with ' / " and then press SET to confirm.
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
MENU
G-CODE
TIMER
TITLE
DVD MENU
MODE
CHANNEL PRESET
CLOCK
CLEAR
RETURN
SET
ENTER
LANGUAGE
ZERO BACK
:SELECT
SET:ENTER
MENU:EXIT
SKIP SEARCH
3
Set “NTSC” to “3.58”, “4.43” or “PAL TV” with \ / |.
Then press ".
AM/PM
INPUT SELECT VCR DVD
/
REV
FWD
COLOUR
AUTO PAL MESECAM NTSC
PLAY
NTSC
3.58 4.43 PAL TV
BLUE BACK
AUTO RENTAL
REPEAT
NICAM
S.PICTURE
:SELECT
SET:ENTER
AUTO
ON
ON
AUTO
ON
:CHANGE
MENU:EXIT
OFF
OFF
OFF
OFF
OFF
REC
PAUSE/STILL
STOP
TAPE
SPEED
DPSS
SKIP
SLOW
AUDIO
OUTPUT
CH
NTSC 3.58 ..... When using NTSC 3.58 TV system.
(Input signal: NTSC 3.58)
VCR
DVD
NTSC 4.43 ..... When using NTSC 4.43 TV system.
(Input signal: NTSC 4.43)
PAL TV........... When using PAL TV system.
(Input signal: NTSC 4.43)
VCR/DVD COMBINATION
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
25
VCR Setup
4
Set “NICAM” to “AUTO” or “OFF” with \ / |. Then press ".
COLOUR
AUTO PAL MESECAM NTSC
NTSC
3.58 4.43 PAL TV
BLUE BACK
AUTO RENTAL
REPEAT
NICAM
S.PICTURE
AUTO
ON
ON
AUTO
ON
OFF
OFF
OFF
OFF
OFF
G-CODE
PROG
DV- NC70W
DV- NC70
DV- NC70X
:SELECT
SET:ENTER
:CHANGE
MENU:EXIT
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
ON
VCR/DVD VCR MENU
AUTO............. Usually select “AUTO”.
OFF................ Select “OFF” when your TV does not have good
NICAM signal reception and a lot of noise is
heard when the AUTO mode is set. (Selecting
“OFF” will change it to normal audio signal
reception.)
SCREEN SELECTOR DVD SETUP
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
TITLE
DVD MENU
CLEAR
RETURN
SET
ENTER
ZERO BACK
• You can change the COLOUR, BLUE BACK, AUTO RENTAL,
REPEAT and S.PICTURE settings the same way (See pages
55, 56, 58 and 59).
SKIP SEARCH
5
Press SET to enter.
• The screen returns to normal.
AM/PM
INPUT SELECT VCR DVD
/
REV
FWD
PLAY
• If you press VCR MENU to exit the mode selection screen in Step 4,
the data will not be stored. Be sure to press SET to store the data.
REC
PAUSE/STILL
STOP
TAPE
SPEED
DPSS
SKIP
SLOW
AUDIO
OUTPUT
CH
VCR
DVD
VCR/DVD COMBINATION
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
26
VCR Setup
Setting the Channels
Your Product can receive VHF channels 1A to E12 (US AIR 2 to 13), CATV/HYPER channels S1 to S41 and UHF
channels E21 to E69 (US AIR 14 to 78). Your Product has 84 programmable channel positions, each of which
can be set to any of the broadcast and CATV/HYPER channels.
• Channel positions 13 through 83 will not be displayed when selected. These channel positions have been set
at the factory to be skipped.
• To view a skipped channel position, tune that position to a broadcast CATV/HYPER channel, or cancel the
channel skip function for that position.
BROADCAST TV CHANNEL
BROADCAST TV CHANNEL
BROADCAST TV CHANNEL
000
001
002
003
004
005
006
007
008
009
0
01 01
02 02
081 S-1
97
082 S-2 Z-1 99
083 S-3 Z-2 14
084 S-4 Z-3 15
085 S-5 Z-4 16 5A
149
150
151
152
153
154
155
156
157
158
159
160
41
Z-12 42
45
Z-12 46
49
50
53
Z-12 54
57
Z-12 58
61
Z-12 62
1A
E-2 C-1
E-3 C-2 02 03 03
E-4 C-3 03 04 04
E-5 C-7 07 05 05
E-6 C-8 08 06 06
E-7 C-9 09 07 07
086 S-6
17
087 S-7 Z-5 18
088 S-8 Z-6 20
089 S-9 Z-7 21
090 S-10 Z-8 22
091 S-11 Z-9 25
092 S-12 Z-10 26
093 S-13 Z-11 28
E-8 10 08 08
E-9 C-10 12 09 09
010 E-10 C-11 13 10 10
011 E-11 C-12 23 11
012 E-12 Z-8 24
021 E-21 C-13
094 S-14
29
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
66
67
69
70
71
73
74
75
77
78
81
82
83
85
86
87
022 E-22 C-14 67
023 E-23 C-15 68
024 E-24 C-16 69
025 E-25 C-17 71
026 E-26 C-18 72
027 E-27 C-19 73
028 E-28 C-20 75 28
029 E-29 C-21 76 29
030 E-30 C-22 77 30
031 E-31 C-23 79 31
032 E-32 C-24 80 32
033 E-33
034 E-34
035 E-35
036 E-36
037 E-37
038 E-38 C-25 88 38
039 E-39 C-26 89
040 E-40 C-27 91
041 E-41 C-28 92
042 E-42 C-29 93
043 E-43 C-30 100
044 E-44 C-31 101
045 E-45 C-32 102
046 E-46 C-33 104
047 E-47 C-34 105
048 E-48 C-35 106
049 E-49 C-36 108
050 E-50 C-37 109
051 E-51 C-38 110
052 E-52 C-39 112
053 E-53 C-40 113
054 E-54 C-41 114
055 E-55 C-42 116
056 E-56 C-43 117
057 E-57 C-44 118
058 E-58 C-45 120
059 E-59 C-46 121
060 E-60 C-47 122
061 E-61 C-48 124
062 E-62 C-49 125
063 E-63 C-50
095 S-15 Z-12 30
096 S-16 Z-13 31
097 S-17 Z-14 32
098 S-18 Z-15 33
099 S-19 Z-16 35
100 S-20 Z-17 36
101 S-21 Z-18 37
102 S-22 Z-19 39
103 S-23 Z-20 40
104 S-24 Z-21 41
105 S-25 Z-22 43
106 S-26 Z-23 44
107 S-27 Z-24 45
108 S-28 Z-25 47
109 S-29 Z-26 48
110 S-30 Z-27 49
111 S-31 Z-28 51
112 S-32 Z-29 52
113 S-33 Z-30 53
114 S-34 Z-31 55
115 S-35 Z-32 56
116 S-36 Z-33 57
117 S-37 Z-34 59
118 S-38 Z-35 60
119 S-39 Z-36 61
120 S-40 Z-37 63
81 33
83 34
84 35
85 36
87 37
90
91
93
94
100
102
104
106
107
108
110
111
114
115
116
118
119
120
123
124
121 S-41
64
04
C-4 05
C-5 06
95
96
Z-2 29
C-3
122
123
124
X
Y
Z
125 Z+1
126 Z+2
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
C-4 05
97
98
99
Z-5 18
19
19
064 E-64 C-51
065 E-65 C-52
066 E-66 C-53
067 E-67 C-54
068 E-68 C-55
069 E-69 C-56
20
09
10
11
25
26
27
32
33
34
37
38
67
68
69
070
071
072
073
074
075
C-57
79
89
103
112
122
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
27
VCR Setup
Auto Tuning
Preparation
•
Press OPERATE. Then move the VCR/DVD CHANGE Switch to VCR.
• Ensure the Video channel is selected on the TV.
G-CODE
PROG
DV- NC70W
1
Press VCR MENU. Press ' / " to select “CHANNEL PRESET”.
Press SET to confirm.
DV- NC70
DV- NC70X
TIMER
MENU
OPERATE
DISPLAY
ON/OFF
EJECT
G-CODE
TIMER
MODE
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
CHANNEL PRESET
CLOCK
LANGUAGE
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
TITLE
DVD MENU
:SELECT
SET:ENTER
MENU:EXIT
CLEAR
RETURN
SET
ENTER
2
3
Press ' / " to select “AUTO”. Press SET to confirm.
ZERO BACK
CHANNEL PRESET
AUTO
MANUAL
SKIP SEARCH
AM/PM
INPUT SELECT VCR DVD
/
:SELECT
REV
FWD
SET:ENTER
MENU:EXIT
PLAY
REC
PAUSE/STILL
Press \ / | to select the SYSTEM you desire. Press SET to
confirm. Select the broadcast system used for areas where I,
B/G, D/K, M reception is necessary. (For DV-NC70X, only B/G
and D/K will appear on the screen.)
STOP
TAPE
SPEED
DPSS
SKIP
SLOW
AUDIO
OUTPUT
CH
AUTOMATIC TUNING
VCR
DVD
SYSTEM
I B/G D/K M
:CHANGE
MENU:EXIT
VCR/DVD COMBINATION
SET:ENTER
I,B/G,D/K,M (Receiving system)
Hong Kong
I
China, Russia
D/K
South East Asia,
Australia, New
Zealand
U.S.A., Japan,
Philippine
Ex.
B/G
M
• If the broadcast signal system does not match the Product receiving
system, tuning is not possible.
4
The channel display on the TV screen will continue through all of
the channels and when finished, the TV screen will return to the
MOVE (channel sort) screen. The bar display indicates the
estimated amount of channels tuned.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
28
VCR Setup
5
6
To change the order of tuned-in broadcast, press '/ "/ \/ |
to select the channel to be moved. Press SET to confirm .
“SELECTED: CH078” will appear.
MOVE
1/5
1CH002
2CH003
3CH004
4CH075 10
5CH078 11
7
8
9
13
14
15
16
17
18
G-CODE
DV- NC70W
PROG
DV- NC70
DV- NC70X
6
12
SELECTED :CH078
:SELECT
SET:ENTER
MENU:EXIT
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
Press '/ "/ \/ | to select the new position for the channel.
Then, press SET to confirm.
“SELECTED: CH078” will disappear.
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
TITLE
DVD MENU
MOVE
1/5
CLEAR
RETURN
SET
1CH078
2CH002
3CH003
4CH004 10
5CH075 11
7
8
9
13
14
15
16
17
18
ENTER
ZERO BACK
6
12
:SELECT
SKIP SEARCH
SET:ENTER
MENU:EXIT
AM/PM
INPUT SELECT VCR DVD
/
7
8
To move additional channels, repeat steps 5 and 6.
REV
FWD
When the channels have been sorted into the desired order,
press VCR MENU to return to the normal screen.
PLAY
REC
PAUSE/STILL
STOP
TAPE
SPEED
DPSS
SKIP
SLOW
• If additional unwanted channels are found, refer to page 32 to skip them.
• If some channels are unable to be found, refer to “Manual Tuning” the
next page.
AUDIO
OUTPUT
CH
VCR
DVD
VCR/DVD COMBINATION
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
29
VCR Setup
Manual Tuning
Preparation
• Press OPERATE. Then move the VCR/DVD CHANGE Switch to
VCR.
• Ensure the Video channel is selected on the TV.
G-CODE
PROG
DV- NC70W
DV- NC70
DV- NC70X
Example: Tuning Channel Position 48 to Broadcast TV Channel E7
(VCR CHANNEL 007 for system I area.)
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
1
Press VCR MENU. Press '/ "to select “CHANNEL PRESET”
and press SET to confirm.
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
MENU
G-CODE
TIMER
TITLE
DVD MENU
MODE
CHANNEL PRESET
CLOCK
CLEAR
RETURN
SET
ENTER
LANGUAGE
ZERO BACK
:SELECT
SET:ENTER
MENU:EXIT
SKIP SEARCH
2
3
Press '/ "to select “MANUAL” and press SET to confirm.
AM/PM
INPUT SELECT VCR DVD
CHANNEL PRESET
AUTO
MANUAL
/
REV
FWD
PLAY
REC
PAUSE/STILL
STOP
:SELECT
SET:ENTER
MENU:EXIT
TAPE
SPEED
DPSS
SKIP
SLOW
AUDIO
OUTPUT
Select the preset channel position number 48 with the number
buttons (0 to 9) or \/ |and press ".
CH
VCR
DVD
PRESET CH
SYSTEM
CHANNEL
FINE TUNING
SKIP
48
I B/G D/K M
002
ON
OFF
VCR/DVD COMBINATION
:SELECT
:CHANGE
SET:ENTER
MENU:EXIT
4
Press \/ | to select the “SYSTEM” you desire and press ".
(For DV-NC-70X, only B/G and D/K will appear on the screen.)
PRESET CH
SYSTEM
CHANNEL
FINE TUNING
SKIP
48
I B/G D/K M
002
ON
OFF
:SELECT
:CHANGE
SET:ENTER
MENU:EXIT
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
30
VCR Setup
5
Press the number buttons (0 to 9) or \/ |until you see the
desired broadcast channel E7 (VCR CHANNEL 007) on your TV
and press ".
PRESET CH
SYSTEM
CHANNEL
FINE TUNING
SKIP
48
I B/G D/K M
007
G-CODE
DV- NC70W
PROG
DV- NC70
DV- NC70X
ON
OFF
TIMER
:SELECT
SET:ENTER
:CHANGE
MENU:EXIT
OPERATE
DISPLAY
ON/OFF
EJECT
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
6 For fine tuning, press \/ | until the broadcast channel comes in
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
clearly on your TV.
TITLE
DVD MENU
PRESET CH
SYSTEM
CHANNEL
FINE TUNING
SKIP
48
CLEAR
RETURN
SET
I B/G D/K M
007
ENTER
ZERO BACK
ON
OFF
SKIP SEARCH
:SELECT
:CHANGE
SET:ENTER
MENU:EXIT
AM/PM
INPUT SELECT VCR DVD
/
7 To check that the broadcast channel you tuned the Product to is
REV
FWD
VHF E7, select channel 7 using the TV tuner.
PLAY
8
9
Select the video channel on your TV again.
• If the channel you tuned the Product to and the one on the TV
do not match, repeat steps 5 through 7.
REC
PAUSE/STILL
STOP
TAPE
SPEED
DPSS
SKIP
SLOW
AUDIO
OUTPUT
CH
Press SET. (This will set channel position 48 in memory and
return to channel position 49 for tuning.)
VCR
DVD
10 If you want to set additional channels, repeat steps 3 through 9.
11 Press VCR MENU to return to the normal screen.
VCR/DVD COMBINATION
• Use Auto Tuning normally for presetting.
1Auto tuning may not be able to preset some broadcasts.
Use manual tuning to preset.
2The same broadcast may be preset more than once.
Select the channel with the clearer broadcast.
3After auto tuning is completed, confirm the preset channels in
order.
If no sound can be heard from any of the preset channels, reset the
SYSTEM (I, B/G, D/K, M) with manual tuning.
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
31
VCR Setup
Channel Skip/Cancelling Skip
Channel Skip
If there are channel positions that are not preset, you can skip them
with the following procedure.
G-CODE
PROG
DV- NC70W
DV- NC70
DV- NC70X
Preparation
• Press OPERATE. Then move the VCR/DVD CHANGE Switch to
VCR.
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
Example: Skip channel position 12.
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
1
Press VCR MENU. The menu screen will appear. Press '/ "to
select “CHANNEL PRESET” and press SET to confirm.
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
TITLE
DVD MENU
MENU
CLEAR
RETURN
SET
ENTER
G-CODE
TIMER
MODE
CHANNEL PRESET
CLOCK
ZERO BACK
LANGUAGE
SKIP SEARCH
:SELECT
SET:ENTER
MENU:EXIT
AM/PM
INPUT SELECT VCR DVD
/
2
3
4
Press '/ "to select “MANUAL”. Press SET to confirm.
REV
FWD
PLAY
CHANNEL PRESET
AUTO
MANUAL
REC
PAUSE/STILL
STOP
TAPE
SPEED
DPSS
SKIP
SLOW
AUDIO
OUTPUT
:SELECT
CH
SET:ENTER
MENU:EXIT
VCR
DVD
Set the channel position you wish to skip with \/ |or number
buttons (0 to 9).
PRESET CH
SYSTEM
CHANNEL
FINE TUNING
SKIP
12
I B/G D/K M
012
VCR/DVD COMBINATION
ON
OFF
:SELECT
:CHANGE
SET:ENTER
MENU:EXIT
Press '/ "to select “SKIP”.
PRESET CH
SYSTEM
CHANNEL
FINE TUNING
SKIP
12
I B/G D/K M
012
ON
OFF
:SELECT
:CHANGE
SET:ENTER
MENU:EXIT
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
32
VCR Setup
5
Press \/ | to set “ON” and press SET to confirm.
PRESET CH
SYSTEM
CHANNEL
FINE TUNING
SKIP
12
I B/G D/K M
012
G-CODE
ON
OFFF
DV- NC70W
PROG
DV- NC70
DV- NC70X
:SELECT
:CHANGE
SET:ENTER
MENU:EXIT
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
6
7
If you wish to set more channels to be skipped, repeat steps 3
through 5.
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
Press VCR MENU to return to the normal screen.
TITLE
DVD MENU
CLEAR
RETURN
SET
• When making channel inputs with the number buttons (0 to 9), first
select the one figure input or two figures input using the -/-- button on
the Remote.
ENTER
ZERO BACK
SKIP SEARCH
AM/PM
INPUT SELECT VCR DVD
/
REV
FWD
PLAY
REC
PAUSE/STILL
STOP
TAPE
SPEED
DPSS
SKIP
SLOW
AUDIO
OUTPUT
CH
VCR
DVD
VCR/DVD COMBINATION
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
33
VCR Setup
Cancelling Skip
Example: Reset channel position 12.
1
Follow the steps 1 and 2 from “Channel Skip” on page 32.
G-CODE
PROG
DV- NC70W
DV- NC70
DV- NC70X
2
Select the channel position you wish to unskip with \/ |or
number buttons (0 to 9).
PRESET CH
SYSTEM
CHANNEL
FINE TUNING
SKIP
12
I B/G D/K M
012
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
ON
OFF
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
:SELECT
:CHANGE
TITLE
DVD MENU
SET:ENTER
MENU:EXIT
CLEAR
RETURN
SET
ENTER
3
4
Press '/ "to select “SKIP”.
ZERO BACK
PRESET CH
SYSTEM
CHANNEL
FINE TUNING
SKIP
12
SKIP SEARCH
I B/G D/K M
012
ON
OFFF
AM/PM
INPUT SELECT VCR DVD
/
REV
FWD
:SELECT
SET:ENTER
:CHANGE
MENU:EXIT
PLAY
REC
PAUSE/STILL
Press \/ |to set “OFF” and press SET to confirm.
STOP
TAPE
SPEED
DPSS
SKIP
SLOW
PRESET CH
SYSTEM
CHANNEL
FINE TUNING
SKIP
12
I B/G D/K M
012
AUDIO
OUTPUT
CH
ON
OFF
VCR
DVD
:SELECT
:CHANGE
SET:ENTER
MENU:EXIT
VCR/DVD COMBINATION
5
6
If you wish to unskip more channels, repeat steps 2 through 4.
Press VCR MENU to return to the normal screen.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
34
VCR Setup
Setting the Clock
When you use the Product for the first time or after a power failure of
more than 60 minutes the clock has to be reset. Apply power to the
Product to switch it on. Then perform the following procedure.
G-CODE
DV- NC70W
Initial Setting of Clock
PROG
DV- NC70
DV- NC70X
1
2
First set the language and system setting. (See page 21.) Then
press SET.
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
Press ' / " to select whether the clock should show 12-hour AM/
PM time or 24-hour time and press |.
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
CLOCK
TITLE
DVD MENU
MODE
24H
TIME
0:00
DATE
1/01
YEAR
00
CLEAR
RETURN
SET
ENTER
ZERO BACK
MODE:24H/12H
:SELECT
SET:ENTER
:CHANGE
MENU:EXIT
SKIP SEARCH
3
Set the present time with the number buttons (0 to 9) or ' / " on
the Remote and press |. (First set the “hour” digits and the
“minute”. If there is only one “hour” or one “minute” digit, enter a 0
first.)
AM/PM
INPUT SELECT VCR DVD
/
REV
FWD
PLAY
CLOCK
REC
PAUSE/STILL
MODE
24H
TIME
10:28
DATE
1/01
YEAR
00
STOP
TAPE
SPEED
DPSS
SKIP
SLOW
AUDIO
OUTPUT
CH
:SELECT
SET:ENTER
:CHANGE
MENU:EXIT
VCR
DVD
• If 12H mode is selected, set the AM or PM indicator.
VCR/DVD COMBINATION
4
Set the date with the number buttons (0 to 9) or ' / " on the
Remote and press |. (First set the “day” digits and then the
“month”. If there is only one “day” or one “month” digit, enter a 0
first.)
CLOCK
MODE
24H
TIME
10:28
DATE
15/12
YEAR
00
DATE :DAY/MONTH
:SELECT
:CHANGE
SET:ENTER
MENU:EXIT
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
35
VCR Setup
5
6
Set the year digits with the number buttons (0 to 9) or ' / " on
the Remote. (If there is only one “year” digit, enter a 0 first.)
CLOCK
MODE
24H
TIME
10:28
DATE
15/12
YEAR
00
G-CODE
PROG
DV- NC70W
DV- NC70
DV- NC70X
SELECT :
ENTER :SET
CHANGE:
EXIT :MENU
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
Press SET to return to the normal screen.
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
Changing the Clock Setting
TITLE
DVD MENU
1
If the clock has already been set previously and you want to
change it, select “CLOCK” from the MENU, and then follow the
steps 1 to 6 from “Initial Setting of Clock” on pages 35 and 36.
CLEAR
RETURN
SET
ENTER
ZERO BACK
SKIP SEARCH
2
Press VCR MENU. Press ' / " to select “CLOCK” and press
SET to confirm. Press VCR MENU to return to the normal screen.
AM/PM
INPUT SELECT VCR DVD
MENU
/
G-CODE
TIMER
MODE
REV
FWD
CHANNEL PRESET
CLOCK
PLAY
LANGUAGE
REC
PAUSE/STILL
:SELECT
STOP
SET:ENTER
MENU:EXIT
TAPE
SPEED
DPSS
SKIP
SLOW
AUDIO
OUTPUT
CH
VCR
DVD
• If the precise clock time is required (within a second), do not press
SET until the exact start of the minute after setting the year (after
completing step 5). The clock will start operation as soon as SET is
pressed.
• If you prefer the clock display time in the 12-hour AM/PM system,
select “12H” in step 2. In this case, when you set the present time
using the number buttons, first press AM/PM on the Remote to select
AM or PM, and then set the present time.
VCR/DVD COMBINATION
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
36
VCR Setup
Setting the Language
This Product is factory preset to display the LANGUAGE setting
screen after VCR MENU is pressed when the Product is operated for
the first time. In some cases, the retailer may have already set the
language, and the CLOCK setting screen will appear after VCR
MENU is pressed. To reset the Product, perform the following steps.
G-CODE
DV- NC70W
PROG
DV- NC70
DV- NC70X
VCR-RESET
TIMER
OPERATE
DISPLAY
1
2
3
Press OPERATE to POWER OFF on the Product.
ON/OFF
EJECT
Press OPERATE to POWER ON on the Product.
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
Press VCR MENU and CH " on the Remote at the same time
for five seconds. (The LANGUAGE setting screen should appear.)
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
TITLE
DVD MENU
CLEAR
RETURN
SET
ENTER
• When the Product is reset, all channel settings, guide channel setting
for the G-CODE system and timer setting will be cancelled.
ZERO BACK
SKIP SEARCH
Initial Setting of Language
Preparation
• Press OPERATE. Then move the VCR/DVD CHANGE Switch to
VCR.
AM/PM
INPUT SELECT VCR DVD
/
REV
FWD
1
Press ' / " to select the language and press SET to confirm.
PLAY
LANGUAGE
ENGLISH
REC
PAUSE/STILL
STOP
TAPE
SPEED
DPSS
SKIP
SLOW
AUDIO
OUTPUT
CH
Changing Language
DVD
VCR
If the language has already been set previously and you want to
change it, follow the steps below.
1
Press VCR MENU. Press ' / " to select “LANGUAGE ” and
press SET to confirm.
VCR/DVD COMBINATION
MENU
G-CODE
TIMER
MODE
CHANNEL PRESET
CLOCK
LANGUAGE
:SELECT
SET:ENTER
MENU:EXIT
2
3
Select the language with ' / " and press SET to confirm.
LANGUAGE
ENGLISH
Press VCR MENU to return to the normal screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
37
VCR Display Information
The tape counter and VCR mode can be shown on the screen while you are playing back a tape or watching a
broadcast on the video channel.
Display example
PLAY, X2
VSF, FF
Programme channel
position
2
Operating mode
S. PICTURE
Multiplex sound indicator
S.PICTURE ON
SP STOP 11:30
NICAM
II
L R
VSR, REW
STOP, CASSETTE IN
F.ADV
(
: stereo)
I/
(Sharp Super Picture)
Tape Speed
Simple Recording timer
Audio Output indicator
Repeat display
SLOW
REPEAT
12:30
21/08 00
19
DPSS
0:00.00
Clock display
STILL
Calendar display
DPSS
REC
REC PAUSE
Real time tape counter
How to Display Indicators
1
2
3
Turn on your TV and select the video channel.
Press OPERATE to turn on the Product. Mode indicators are displayed in the AUTO display screen.
Each time ON SCREEN is pressed, the screen changes as follows:
AUTO Display → FULL Display → Counter Display → Display OFF
AUTO DISPLAY
When an operation button, number buttons or CH ' / " is pressed, the current mode or the number of the
channel will be displayed in the upper section of the TV screen for about 3 seconds.
• When you record a video signal output from this Product on another VCR, press ON SCREEN to select Display Off. (If
the mode indicator is displayed on the screen, it is also recorded on the tape.)
VCR Front Panel Display
Each time DISPLAY on the Remote is pressed, the display changes in the following way. (However, the follow-
ing is the case when the clock time is set and displayed in the 12-hour system.)
Channel setting mode → Tape counter mode → Clock mode
• Channel setting mode .. The number of the channel will be displayed. It does not display during playback.
• Tape counter mode ....... The current tape position will be displayed.
• Clock mode.................... The current time will be displayed.
The meaning of the main indicators is shown below. (This list does not include all indicators.)
Display Examples
Cassette-In
Indicator
Slow, Still,
Frame Advance
When AC power cord
is first plugged in
Rotate
slowly
Playback
Rotate
rapidly
Rewind,
Video Search Rewind
Stop
Fast forward,
Video Search Forward
Rotate
rapidly
LINE IN 1/2
Rotate
slowly
Record
Rec Pause
• Tape counter is displayed during playback, fast forward or rewind operation.
• When the power is turned off, the clock is displayed and the VCR Front Panel Display Becomes darker.
• The display will return to the original mode (counter or clock display) 3 seconds after the VCR enters the operation
mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
38
DVD Setup
DVD Setup ....................................................................................... 40
About the SETUP Screen .............................................................. 40
TV MODE Setting .......................................................................... 41
PARENTAL Level Setting ............................................................... 42
AUDIO Setting ............................................................................... 44
Setting the COMPRESSION (Dolby Digital output level)............ 44
Setting the DOLBY DIGITAL ....................................................... 45
Setting the MPEG ....................................................................... 46
Setting the CINEMA VOICE........................................................ 46
DISC LANGUAGE Setting ............................................................. 47
Setting SUBTITLE, AUDIO and MENU languages ..................... 47
Selecting languages from OTHER.............................................. 48
DVD Display Information ................................................................ 49
Operation Mode Indicators............................................................. 49
Language Code List for Disc Language ....................................... 50
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
39
DVD Setup
About the SETUP Screen
This section describes how to specify various basic settings using the
SETUP screen. The list below shows all the items you can set and
adjust. See the following pages for details on each setup procedure.
• The setting procedures described on the following pages are
available only in STOP mode.
• The OSD (On Screen Display) screens used in this Operation
Manual are purely for the purposes of explanation. The actual
displays (set displays) may differ slightly from what is shown here.
(Example) TV MODE
TV MODE
:
:
43
43
PS
LB
:
16 9
SELECT
ENTER
ENTER
RETURN
Important!
• When you set the language to be used in the OSD, changing the
mode to “VCR” and select “LANGUAGE” in the menu screen.
See OSD Language Setting on page 37 for details.
Setup item list
Main Menu
4 : 3 PS
TV MODE
41
• Specifies the setting for the type of TV connected
and the playback format for wide-screen video
material.
4 : 3 LB
16 : 9
PARENTAL [1 to 8 (ON)/OFF]/Selecting the Country Code
42
• Sets or changes the parental level (1 to 8).
• Used to set or change the password used to
prevent the parental level from being changed too easily.
• See page 43 for Country Code.
COMPRESSION [ON/OFF]
DIGITAL
AUDIO
44
• Use this setting for increasing the average
volume of Dolby Digital audio when playing a
DVD.
BITSTREAM
D-PCM
• Use this setting for specifying either
“BITSTREAM” or “D-PCM” as the digital type.
MPEG
BITSTREAM
PCM
CINEMA VOICE[ON/OFF]
AUDIO
ENGLISH
SPANISH
DISC LANGUAGE
47
• Use this setting for selecting languages of
subtitle, audio track and disc menu recorded on
a disc.
FRENCH
ITALIAN
GERMAN
CHINESE
SWEDISH
DUTCH
OTHER
Languages you
can select are
same as above.
SUB TITLE
MENU
Languages you
can select are
same as above.
• Numbers in
refer to the pages where the setting
procedures are described.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
40
DVD Setup
G-CODE
TV MODE Setting
DV- NC70W
PROG
DV- NC70
DV- NC70X
Preparation
• See Preparing to Watch a DVD on page 18.
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
1
2
While this product is stopped, press DVD SETUP to display the
SETUP screen.
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
Use ' or " to select the “
TV MODE”.
TITLE
DVD MENU
CLEAR
RETURN
SET
ENTER
:
TV MODE
PARENTAL
AUDIO
43
PS
LEVEL 8
ZERO BACK
SKIP SEARCH
DISC LANGUAGE
SELECT
ENTER
AM/PM
INPUT SELECT VCR DVD
ENTER
RETURN
/
REV
FWD
3
4
Press ENTER to display the items you can select.
PLAY
REC
PAUSE/STILL
4:3 PS
4:3
:
LB
16 9
Use ' or " to select
,
or
.
STOP
4:3 PS
(Example) Selecting
.
TAPE
SPEED
DPSS
SKIP
SLOW
AUDIO
OUTPUT
CH
VCR
DVD
TV MODE
:
:
43
43
PS
LB
:
16 9
VCR/DVD COMBINATION
SELECT
ENTER
ENTER
RETURN
4:3 PS
•
— (Pan & Scan mode): When wide-screen video
material is played, this mode clips the right and left sides of
the image so that it can be viewed on a conventional TV
screen.
Cut off when a wide-screen video
image is played.
• Some wide-screen DVDs that do not permit Pan & Scan mode
playback are automatically played in letterbox mode (black bands
top and bottom).
4:3 LB
•
•
— (Letterbox mode): When wide-screen video material
is played in this mode on a conventional TV screen, black
bands appear at the top and bottom of the screen.
:
16 9
— (Wide-screen TV): This is the correct mode for playing
wide-screen videos on a wide-screen TV.
• You must also set the screen mode on your wide-screen TV to
“FULL”.
5
6
Press ENTER to confirm the “TV MODE” setting.
If you want to complete the settings here, press RETURN to exit
the SETUP screen and return to the normal screen.
• If you intend to go on and specify other settings (PARENTAL,
AUDIO or DISC LANGUAGE), press ' or " to display other
SETUP screen without pressing RETURN.
The actual appearance of the
image depends on the screen
mode setting of your wide-
screen TV.
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
41
DVD Setup
PARENTAL Level Setting
Certain discs come preset with country codes and parental level
settings defined for particular countries. Discs equipped with the
parental lock function are rated according to their content. The rated
content allowed by a parental lock level and the way a DVD can be
controlled vary from disc to disc. Some discs, for example, may let
you edit out scenes and replace them with scenes suitable for
children. You can also use the parental lock to completely disable
playback of the DVD.
G-CODE
PROG
DV- NC70W
DV- NC70
DV- NC70X
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
Preparation
• See Preparing to use DVD on page 78.
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
TITLE
DVD MENU
1
2
Press DVD SETUP to display the SETUP screen.
CLEAR
RETURN
SET
ENTER
Use ' or " to select the “
PARENTAL” and then press
ENTER.
ZERO BACK
• The password specification and verification screen appears.
For DV-NC70X model, the parental country code is “Australia”.
SKIP SEARCH
PARENTAL
PASSWORD
PASSWORD
LEVEL
AM/PM
INPUT SELECT VCR DVD
????
OFF
/
CODE
CHINA
REV
FWD
SELECT
PLAY
ENTER
ENTER
RETURN
REC
PAUSE/STILL
• If you have already set your password,
verification display) appears.
(password
STOP
TAPE
SPEED
DPSS
SKIP
SLOW
3
Use the number buttons (0 to 9) to enter a 4-digit password.
AUDIO
OUTPUT
CH
Displayed when “1234”
is being entered as the
password.
PASSWORD : 1 2 3 4
VCR
DVD
• Enter the numbers slowly as each number is stored separately.
• If you enter the wrong number three times in succession, the normal
screen reappears.
VCR/DVD COMBINATION
If you forget your password, you can erase your current password by
pressing ËSTOP four times.
4
The cursor is moved to “LEVEL” and then press ENTER.
PARENTAL
LEVEL 1 LEVEL 5
LEVEL 2 LEVEL 6
LEVEL 3 LEVEL 7
LEVEL 4 LEVEL 8
OFF
SELECT
ENTER
ENTER
RETURN
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
42
DVD Setup
5
Press ', ", | or \ to select the desired parental level and
then press ENTER.
G-CODE
DV- NC70W
(Example) Selecting “LEVEL 8”
PROG
DV- NC70
DV- NC70X
PARENTAL
PASSWORD
PASSWORD
LEVEL
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
----
ON
VCR/DVD VCR MENU
8
SCREEN SELECTOR DVD SETUP
CODE
CHINA
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
• Level 1: for most restricted viewing → Level 8: for adult viewing
(The smaller the number, the greater the level of restriction.)
• When “PARENTAL” is set to “OFF”, DVD discs can be played back
regardless of the parental level.
TITLE
DVD MENU
CLEAR
RETURN
SET
ENTER
ZERO BACK
SKIP SEARCH
The parental level set up for CHINA is prepared for future use. As for
the set up of an appropriate level, please check the level when you
purchase your DVD disc equipped with the parental feature.
AM/PM
INPUT SELECT VCR DVD
/
REV
FWD
6
Press " to select “CODE” and then press ENTER.
PLAY
PARENTAL
CODE
USA
CANADA
JAPAN
GERMANY SPAIN
REC
PAUSE/STILL
STOP
FRANCE
UK
ITALY
TAPE
SPEED
DPSS
SKIP
SLOW
AUDIO
OUTPUT
CH
SELECT
VCR
DVD
ENTER
ENTER
RETURN
7
Press ', ", | or \ to select the desired country code and then
press ENTER.
• If you want to go to next page, select the country code
displayed at the bottom, and then press ".
VCR/DVD COMBINATION
PARENTAL
PASSWORD
----
PASSWORD
LEVEL
Country Code List
8
CODE
CHINA
USA
FINLAND
BELGIUM
CANADA
JAPAN
8
Press RETURN to return to the SETUP screen.
• If you want to go on and specify the other settings, use ' or
" to display other SETUP screen. However, press RETURN if
you want to exit the SETUP screen.
HONG KONG
SINGAPORE
THAILAND
MALAYSIA
INDONESIA
TAIWAN
GERMANY
FRANCE
UK
Important!
ITALY
• Be sure to try playing back the disc to confirm that the
parental level setting is working correctly. If it is not working
correctly, try changing the country code.
SPAIN
SWISS
PHILIPPINE
AUSTRALIA
RUSSIA
SWEDEN
HOLLAND
NORWAY
DENMARK
• You can use the parental lock function only with DVD discs that are
equipped with the parental lock feature.
• On some DVD discs, the PARENTAL level setting is fixed and cannot
be modified.
CHINA
• The parental level depends on countries. If you do not set the country
code correctly, it fails to work correctly.
• Some DVD discs allow the viewer to temporarily change the parental
level setting to view the original scenes. When this prompt appears,
input the password to view the original scenes.
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
43
DVD Setup
AUDIO Setting
COMPRESSION ............ Use this setting for increasing the average
volume of Dolby Digital audio when playing
a DVD.
DIGITAL.................. Use this setting for specifying the type of
digital output when playing a disc.
CINEMA VOICE............. Use the setting for raising the sound of the
center speaker to make the voices in a
movie easier to hear.
G-CODE
PROG
DV- NC70W
DV- NC70
DV- NC70X
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
Setting the COMPRESSION
(Dolby Digital output level)
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
When Dolby Digital is used to record the audio on a DVD disc, the
average overall volume level of the audio is relatively lower than that
produced by a VIDEO CD/Audio CD. This is to provide the widest
possible dynamic range. To counteract this, this product automatically
raises the overall average volume level of a disc recorded using Dolby
Digital to a level that is similar to that of a VIDEO CD/Audio CD.
TITLE
DVD MENU
CLEAR
RETURN
SET
ENTER
ZERO BACK
SKIP SEARCH
COMPRESSION:
COMPRESSION:
OFF
ON
AM/PM
INPUT SELECT VCR DVD
/
REV
FWD
PLAY
REC
PAUSE/STILL
DVD
•
Audio level the same
as audio CD, etc.
STOP
Dolby Digital audio
• Low audio level
TAPE
SPEED
DPSS
SKIP
SLOW
AUDIO
OUTPUT
CH
VCR
DVD
VIDEO CDs
Audio CDs
• OFF.............. Audio level recorded on disc is played back without
modification.
VCR/DVD COMBINATION
• ON ............... Dolby Digital average audio level is increased so it
sounds similar to that of a VIDEO CD/Audio CD.
Preparation
• See Preparing to Watching a VCR or a DVD on page 18.
1
2
Press DVD SETUP to display the SETUP screen.
Use ' or " to select the “
AUDIO” and then press ENTER.
AUDIO
COMPRESSION OFF
DIGITAL
MPEG
BITSTREAM
BITSTREAM
CINEMA VOICE OFF
SELECT
ENTER
ENTER
RETURN
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
44
DVD Setup
3
4
Use ' or " to select “COMPRESSION”.
Press ENTER to display the settings you can select.
G-CODE
AUDIO
COMPRESSION
DV- NC70W
ON
OFF
PROG
DV- NC70
DV- NC70X
SELECT
ENTER
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
ENTER
RETURN
ON
VCR/DVD VCR MENU
5
6
Use ' or " to select “ON” or “OFF”.
SCREEN SELECTOR DVD SETUP
• Use of the “OFF” setting is recommended when the product is
connected to audio equipment.
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
TITLE
DVD MENU
Press ENTER to confirm the setting.
CLEAR
RETURN
SET
ENTER
•
When you have completed the above setting, press RETURN to
return to the SETUP screen. However, if you want to specify the
“
DIGITAL” setting in succession, proceed to step 1 below.
ZERO BACK
SKIP SEARCH
• Whenever the “COMPRESSION” setting is “ON”, the 3D VIRTUAL
SURROUND setting is automatically changed to “OFF”.
AM/PM
INPUT SELECT VCR DVD
/
Setting the DOLBY DIGITAL
REV
FWD
When playing a disc recorded using Dolby Digital (5.1ch), you can
PLAY
specify either “BITSTREAM” or “D-PCM” as the digital type output.
REC
PAUSE/STILL
• Before setting the “
page 46.
DIGITAL” , perform the step 1 and 2 on
STOP
TAPE
SPEED
DPSS
SKIP
SLOW
1
2
Use ' or " to select “
DIGITAL”.
AUDIO
OUTPUT
CH
VCR
DVD
Press ENTER to display the settings you can select.
AUDIO
DIGITAL
BITSTREAM
D-PCM
VCR/DVD COMBINATION
SELECT
ENTER
ENTER
RETURN
3
Use ' or " to select “BITSTREAM” or “D-PCM”.
BITSTREAM:
Use this setting for a digital connection of a
receiver (amplifier) equipped with a Dolby
Digital decoder.
D-PCM:
Use this setting for a digital connection to the
(Down Mix PCM) PCM digital input jack of a DAT or MD, or for
a digital connection to a receiver (amplifier)
that does not have a Dolby Digital decoder.
4
5
Press ENTER to confirm the setting.
When you have completed the setting above, press RETURN to
return to the SETUP screen. However, if you want to go on and
specify the other settings, use ' or " to display other setting
screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
45
DVD Setup
Setting the MPEG
•
Before setting the “MPEG”, perform the step 1 to 2 on pages 47 and 48.
1
2
Press ENTER and then use ' or " to select “MPEG”.
Press ENTER to display the settings you can select.
G-CODE
PROG
DV- NC70W
DV- NC70
DV- NC70X
BITSTREAM
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
ON
VCR/DVD VCR MENU
SELECT
ENTER
SCREEN SELECTOR DVD SETUP
ENTER
RETURN
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
3
Use ' or " to select “BITSTREAM” or “PCM”.
TITLE
DVD MENU
BITSTREAM: Use this setting for a digital connection of a
receiver (amplifier) equipped with an MPEG
Audio decoder.
CLEAR
RETURN
SET
ENTER
PCM:
Use this setting for a digital connection to the
PCM digital input jack of a DAT or MD, or for a
digital connection to a receiver (amplifier) that
does not have an MPEG Audio decoder.
ZERO BACK
SKIP SEARCH
4
5
Press ENTER to confirm the setting.
AM/PM
INPUT SELECT VCR DVD
/
Press RETURN to exit the SETUP screen and return to normal screen.
• If you want to go on and specify other settings, use ' or " to
display the other SETUP screen without pressing RETURN.
REV
FWD
PLAY
When playing a disc recorded using DTS, the bitstream type signal
REC
PAUSE/STILL
is output regardless of the setting of “
DIGITAL” and “MPEG”.
STOP
Setting the CINEMA VOICE
TAPE
SPEED
DPSS
SKIP
SLOW
This function is raising the sound of the center speaker to make the
voices in a movie easier to hear.
AUDIO
OUTPUT
CH
VCR
DVD
•
Before setting the “CINEMA VOICE” , perform the step 1 and 2 on page 46.
Use ' or " to select “CINEMA VOICE”.
1
2
Press ENTER to display the settings you can select.
VCR/DVD COMBINATION
AUDIO
CINEMA VOICE
ON
OFF
SELECT
ENTER
ENTER
RETURN
3
Use ' or " to select “ON” or “OFF”.
ON:
Set to “ON” when you want to raise the sound of the voice.
OFF:
Set to “OFF” when you do not want to use this function.
4
5
Press ENTER to confirm the setting.
When you have completed the setting above, press RETURN to
return to the SETUP screen. However, if you want to go on and
specify the other settings, use ' or " to display other setting screen.
• The CINEMA VOICE setting raises the sound of the center channel
threfore it does not affect the voices in other channels.
• Even if this function is set to “ON”, the result may or may not be
effective depending on the disc.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
46
DVD Setup
DISC LANGUAGE Setting
Use this setting for selecting the language for subtitles, audio tracks
and disc menu.
G-CODE
DV- NC70W
Setting SUBTITLE, AUDIO and MENU languages
PROG
DV- NC70
DV- NC70X
Preparation
• See Preparing to Watch a VCR or a DVD on page 18.
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
1
2
Press DVD SETUP to display the SETUP screen.
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
Use ' or " to select the “
DISC LANGUAGE”.
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
:
TV MODE
PARENTAL
AUDIO
43
PS
TITLE
DVD MENU
LEVEL 8
CLEAR
RETURN
SET
ENTER
DISC LANGUAGE
ZERO BACK
SELECT
ENTER
ENTER
RETURN
SKIP SEARCH
3
Press ENTER and then use ' or " to select “AUDIO”,
“SUB TITLE” or “MENU”.
AM/PM
INPUT SELECT VCR DVD
•
You can set “AUDIO”, “SUB TITLE” or “MENU” individually.
/
(Example) Selecting “AUDIO”
REV
FWD
PLAY
DISC LANGUAGE
AUDIO
SUB TITLE
MENU
ENGLISH
ENGLISH
ENGLISH
REC
PAUSE/STILL
STOP
TAPE
SPEED
DPSS
SKIP
SLOW
SELECT
AUDIO
OUTPUT
ENTER
ENTER
RETURN
CH
4
5
After selecting the item, press ENTER.
VCR
DVD
• After selecting “MENU”, make sure to set the language by
following steps 2 to 5 under “Selecting languages from
OTHER” on the next page.
Select the language you want to use with ', ", \ and |.
VCR/DVD COMBINATION
(Example) Selecting “FRENCH”
AUDIO
ENGLISH
SPANISH
FRENCH
ITALIAN
GERMAN
CHINESE
SWEDISH
DUTCH
RUSSIAN
OTHER
SELECT
ENTER
ENTER
RETURN
• If you want to use any languages which are not on the
OSD, proceed to step 1 under “Selecting languages from
OTHER” on the next page.
6
7
Press ENTER to confirm the setting.
Repeat steps 4 to 7 above to go on with other “DISC
LANGUAGE” settings in succession.
•
If you want to complete the setting here, press RETURN to
return to the SETUP screen. However, if you want to display
other setting screens, press ' or " without pressing RETURN.
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
47
DVD Setup
Selecting languages from OTHER
1
Select “OTHER” with ', ", \ and |, then press ENTER to set
the “OTHER” input item (two letters).
• See Language Code List for Disc Language on page 50
G-CODE
PROG
DV- NC70W
when selecting the code.
DV- NC70
DV- NC70X
(Example) Selecting “OTHER” in “AUDIO”
OTHER
TIMER
AUDIO 1 E
AUDIO 2 N
OPERATE
DISPLAY
ON/OFF
EJECT
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
SELECT
ENTER
ENTER
RETURN
TITLE
DVD MENU
• The “SUB TITLE” and “MENU” screens are displayed
respectively when being set.
CLEAR
RETURN
SET
ENTER
ZERO BACK
2
3
Press \ or | to select the alphabet as the first letter on
“AUDIO 1”. (Upper side)
SKIP SEARCH
Press " to move the cursor to “AUDIO 2”. (Lower side)
AM/PM
INPUT SELECT VCR DVD
/
OTHER
AUDIO 1 F
AUDIO 2 A
REV
FWD
PLAY
REC
PAUSE/STILL
STOP
SELECT
ENTER
ENTER
RETURN
TAPE
SPEED
DPSS
SKIP
SLOW
AUDIO
OUTPUT
4
5
Press \ or | to select the alphabet as the second letter.
CH
VCR
DVD
Press ENTER to confirm the setting.
• Press RETURN to return to the previous screen.
VCR/DVD COMBINATION
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
48
DVD Display Information
Operation Mode Indicators
Each time ON SCREEN on the Remote is pressed, the display on the TV screen changes the mode
in the following sequence:
AUTO mode → ON mode → OFF mode
• AUTO mode .... Displays indicators for 3 seconds when operation begins.
• ON mode ......... Displays indicators continually until the operation mode is changed.
• OFF mode ....... Does not display indicators.
Each time DISPLAY on the Remote is pressed, the DVD Front Panel Display changes the mode in
the following sequence:
Time mode
• Time mode ..................... Displays the playing time*.
Operation Status mode .... Displays the operation you perform such as “PLAY”, “REV”.
→
Operation Status mode
→
Title mode
•
• Title mode ...................... Displays the total number of titles, chapters, or tracks.
* When the disc you attempt to play has no information on time, the operation status is displayed.
This product displays the information shown below on the TV screen and on the DVD Front Panel Display
depending on the operation status.
Display Examples
TV Screen
DVD Front Panel Display
Remarks
“– – – – –” appears when the
tray is closed and:
If no disc is loaded or
an unplayable disc is
loaded when this
1) There is no disc in the tray.
2) The disc type is not DVD,
VIDEO CD or Audio CD.
3) The disc is not loaded
correctly (upside-down, etc.)
product is switched on
Tray open
Tray closed
Loading
The indicator changes to show
other indicators (total time, etc.)
Ë
Stopped
Playing
û
When a DVD or VIDEO CD is
played back.
Still/Paused
â
When an Audio CD is played
back.
è
È
Fast forward
Fast reverse
Slow
Does not work with Audio CDs.
Playback Control
Region (Local) Number Error Indicator
If the region (local) number of the disc that you attempt to play differs from the region number of this product,
REGION CODE ERROR” appears on the TV screen and the disc tray slides out. (The disc cannot be
played.)
“
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
49
Language Code List for Disc Language
Code
Language Name
Code
FY
GA
GD
GL
GN
GU
HA
HI
Language Name
Frisian
Code
Language Name
Code
SL
Language Name
Slovenian
Samoan
Shona
AA
AB
AF
AM
AR
AS
AY
AZ
BA
BE
BG
BH
BI
Afar
MG
MI
Malagasy
Maori
Irish
SM
SN
SO
SQ
SR
SS
ST
SU
SV
SW
TA
Abkhazian
Afrikaans
Ameharic
Arabic
Scots Gaelic
Galician
Guarani
MK
ML
MN
MO
MR
MS
MT
MY
NA
NE
NL
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Somali
Albanian
Serbian
Siswat
Gujarati
Assamese
Aymara
Azerbaijani
Bashkir
Byelorussian
Bulgarian
Bihari
Hausa
Hindi
Sesotho
Sundanese
Swedish
Swahili
Tamil
Malay
HR
HU
HY
IA
Croatian
Hungarian
Armenian
Interlingua
Interlingue
Inupiak
Maltese
Burmese
Nauru
Nepali
IE
TE
TG
TH
TI
Telugu
Bislama
Bengali;
Bangla
Dutch
IK
Tajik
BN
NO
OC
OM
OR
PA
Norwegian
Occitan
IN
Indonesian
Icelandic
Italian
Thai
IS
Tigrinya
Turkmen
Tagalog
Setswana
Tonga
BO
BR
CA
CO
CS
CY
DA
DE
DZ
EL
EN
EO
ES
ET
EU
FA
FI
Tibetan
Breton
(Afan) Oromo
Oriya
IT
TK
TL
IW
JA
JI
Hebrew
Catalan
Corsican
Czech
Panjabi
Japanese
Yiddish
TN
TO
TR
TS
TT
PL
Polish
PS
PT
Pashto, Pushto
Portuguese
Quechua
Rhaeto-
Romance
Kirundi
JW
KA
KK
KL
KM
KN
KO
KS
KU
KY
LA
LN
LO
LT
Javanese
Georgian
Kazakh
Turkish
Tsonga
Tatar
Welsh
Danish
QU
RM
German
Bhutani
Greek
Greenlandic
Cambodian
Kannada
Korean
TW
UK
UR
UZ
VI
Twi
Ukrainian
Urdu
RN
RO
RU
RW
SA
SD
SG
SH
English
Esperanto
Spanish
Estonian
Basque
Persian
Finnish
Fiji
Romanian
Russian
Kinyarwanda
Sanskrit
Sindhi
Uzbek
Kashmiri
Kurdish
Vietnamese
Volapük
Wolof
VO
WO
XH
YO
ZH
ZU
Kirghiz
Latin
Xhosa
Sangho
Lingala
Yoruba
Chinese
Zulu
Serbo-
Laothian
Lithuanian
Latvian, Lettish
FJ
Croatian
Singhalese
Slovak
FO
FR
Faroese
French
SI
LV
SK
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
50
Watching the VCR
Playback .......................................................................................... 52
Inserting a Video Cassette ............................................................. 52
Playback......................................................................................... 52
Video Search (with the Remote) .................................................... 52
Fast Forwarding and Rewinding..................................................... 53
Slow Motion Playback (with the Remote)....................................... 53
Still Picture and Frame Advance .................................................... 53
Double Speed Playback ................................................................. 53
NTSC Tape Play Back on PAL TV .................................................. 54
Full Auto Playback ......................................................................... 54
Auto Head Cleaning System .......................................................... 54
Auto Tracking Control System ........................................................ 54
Quick Start with Full Loading Mechanism...................................... 54
AUTO RENTAL............................................................................... 55
COLOUR........................................................................................ 55
BLUE BACK ................................................................................... 56
Playback of Hi-Fi Recorded Tapes ................................................. 57
Audio Output Mode ........................................................................ 57
Adjusting Hi-Fi Audio Tracking ....................................................... 57
Sharp Super Picture ....................................................................... 58
Auto Repeat ..................................................................................... 59
Auto Zero Back................................................................................ 60
DPSS (Digital Program Search System)/Skip Search .................. 61
DPSS ............................................................................................. 61
Skip Search.................................................................................... 61
TV Programme Recording .............................................................. 62
Cassette Erase Protection ............................................................. 62
Recording a TV Programme .......................................................... 62
To Watch Another TV Programme While Recording ...................... 62
Recording NICAM/IGR Multiplex Broadcasts ................................ 63
Simple Recording Timer ................................................................. 64
Immediate Recording ..................................................................... 64
®
Programming the Timer with G-CODE System (DV-NC70W only)... 65
Setting the Programme Number In Step 4 ..................................... 67
Recording with the Timer ............................................................... 68
Confirming Timer Programmes ...................................................... 71
Cancelling Timer Programmes....................................................... 72
Tape Dubbing .................................................................................. 73
Recording a DVD Disc onto a Video Cassette.............................. 74
Recording a DVD disc onto a Video cassette
(Tape Editing mode)................................................................... 74
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
51
Playback
Inserting a Video Cassette
Gently insert the video cassette into the cassette compartment. The
Product turns on automatically. If the cassette is inserted incorrectly,
the loading system will not function. Do not force the cassette into the
OPERAT/
PLAY
STOP
OPEN/CLOSE
TIMER
VCR/DVD
SELECTOR
VCR DVD
(
L
)
-
AV
2
I
N
V
I
D
E
O
MONO AUDIO R
-
Product. When the cassette has been properly loaded, “
pears on the VCR Front Panel display.
” ap-
To remove the cassette, press EJECT during stop mode.
PLAY/ 2
Playback
EJECT / STOP
1
2
3
4
Switch on your TV and select the video channel.
Press OPERATE to turn on the Product.
G-CODE
PROG
DV- NC70W
DV- NC70
DV- NC70X
Insert a cassette.
Press ûPLAY. (The auto tracking control system engages and
“|” flashes on the TV screen for a few seconds.)
TIMER
OPERATE
ON/OFF
EJECT
ON
VCR/DVD VCR MENU
5
Press ËSTOP to stop playback. (If the tape reaches its end, the
Product will automatically rewind the tape to the beginning, eject
the cassette, and turn off the power. If a DVD is being played
back, the power will not turn off.)
DISPLAY
SCREEN SELECTOR DVD SETUP
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
TITLE
DVD MENU
CLEAR
RETURN
SET
ENTER
• NTSC tapes recorded in Hi-Fi and EP mode may appear distorted
during playback. This does not indicate a malfunction. The tracking
function can be used to slightly enhance the picture quality.
ZERO BACK
SKIP SEARCH
Video Search (with the Remote)
AM/PM
INPUT SELECT VCR DVD
/
Use the following procedure to quickly find the section you want,
while viewing the picture.
REV
FWD
PLAY
è
for forward video search, or
1
2
During playback, press FF
È
REC
PAUSE/STILL
REW for reverse search.
STOP
There are 2 search speeds in each direction. The Product
switches between them each time the button is pressed.
TAPE
SPEED
DPSS
SKIP
SLOW
AUDIO
OUTPUT
CH
Press ûPLAY to resume normal playback.
VCR
DVD
• During video search of a tape recorded in the LP mode and EP mode,
the upper part of the picture may be skewed to one side.
TAPE SPEED
VCR/DVD COMBINATION
VSF/VSR1 VSF/VSR2
SP
LP
GG5
GG5
GG9
GG5
GG9
GG9
GG11
GG27
GG7
PAL TAPE
MESECAM TAPE
PAL TAPE
EP
SP/LP
EP
NTSC TAPE
GG21
G
G
VSF : Video Search Forward
VSR : Video Search Reverse
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
52
Playback
Fast Forwarding and Rewinding
1
Press ËSTOP to stop the video tape.
OPERATE EJECT/STOP
REW PLAY/×2
PLAY
STOP
OPEN/CLOSE
è
È
REC
2
3
Press FF
or
REW.
/
TIMER
VCR/DVD
SELECTOR
CH
VCR DVD
(
L
)
-
AV
2
IN VIDEO
MONO AUDIO R
-
Press ËSTOP to stop fast forward/rewind.
CH
/
PLAY/ 2
REW
• If you use other than E-90/E-180 cassettes, fast forward and rewind
may take somewhat longer.
EJECT / STOP
G-CODE
PROG
DV- NC70W
DV- NC70
DV- NC70X
Slow Motion Playback (with the Remote)
1
2
Press SLOW on the Remote during playback.
TIMER
OPERATE
ON/OFF
Press SLOW (to the left of SLOW) to vary the slow
EJECT
/
motion playback speed between 1/5 and 1/30 of the normal
playback speed.
ON
VCR/DVD VCR MENU
DISPLAY
SCREEN SELECTOR DVD SETUP
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
3
Press ûPLAY to resume normal playback.
TITLE
DVD MENU
• No noise can be erased when a tape recorded in the NTSC SP mode
is played back in special modes (still, slow motion, etc.). However, this
does not indicate a malfunction with the Product.
CLEAR
RETURN
SET
ENTER
ZERO BACK
• During slow motion, still picture, frame advance and double speed
playback with a tape recorded in the PAL EP mode, noise may appear.
SKIP SEARCH
Still Picture and Frame Advance
AM/PM
INPUT SELECT VCR DVD
/
1
Press âPAUSE/STILL during playback. This will freeze the
picture on your TV.
REV
FWD
PLAY
2
If noise bars appear on the screen during still picture, set your
Product to the slow mode and press CH ' / " to make the
noise disappear. Then press âPAUSE/STILL again.
REC
PAUSE/STILL
STOP
TAPE
SPEED
DPSS
SKIP
3
If there is vertical jitter during still picture playback, press
CH ' / " to stop jitter.
SLOW
AUDIO
OUTPUT
CH
4
5
Press âPAUSE/STILL during still mode for frame advance.
VCR
DVD
Press ûPLAY again to resume normal playback.
Double Speed Playback
VCR/DVD COMBINATION
1
Press ûPLAY during playback. The tape will be played back at
twice the normal speed.
2
Press ûPLAY to resume normal playback.
• Sound is muted during video search, slow motion, still picture, frame advance and double speed playback.
• To avoid damage to the tape, your Product will resume normal playback after about 5 minutes of slow motion playback
and still picture.
• If an NTSC tape and a PAL or MESECAM tape recorded in LP mode is played back in still picture, frame advance,
slow motion, Double speed, or Video Search mode, the picture may have horizontal jitter and the top of the picture will
be distorted, but this does not indicate VCR malfunction.
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
53
Playback
NTSC Tape Play Back on PAL TV
When you play back an NTSC tape on your Product, it is possible to use a PAL or multi-system compatible TV.
However, please note the following:
• The picture will shrink vertically to some degree, as shown in the diagram,
but this does not indicate a malfunction in your TV or Product.
• If your TV does not have a V-HOLD control, the picture may roll and be
unwatchable. However, if you use a TV with a V-HOLD control, you can
stop the rolling by adjusting the V-HOLD control and watch the picture.
• Horizontal noise bars may appear on the screen during special effect
playback (video search, still, slow, frame advance, and double speed playback), possibly accompanied by
discolouring.
• Although NTSC tapes can be played back into a PAL TV, those tapes cannot be dubbed by a PAL system
VCR connected to the AUDIO OUT and VIDEO OUT terminals of this product. Tapes recorded in this way
cannot be played back on PAL system VCRs.
• Set the Colour mode to AUTO or NTSC, and set the NTSC mode to PAL TV.
Full Auto Playback
(This function only works when AUTO RENTAL mode on the MODE selection screen is set to “OFF”.)
Full Auto Playback lets you enjoy playback with ease. When you insert a cassette with the erasure protection
tab removed, your Product automatically turns on the power and plays back the tape. When the tape reaches
its end, the Product automatically rewinds the tape, ejects it and turns off the power. If a DVD is being played
back, the power will not turn off.
• If the erasure protection hole is covered, press ûPLAY after the power turns on automatically.
Auto Head Cleaning System
When the tape is inserted or ejected, this system automatically cleans the drum and heads with a special roller
before recording or playback begins, protecting the heads and drum from dirt and preserving beautiful picture
quality.
Auto Tracking Control System
This function automatically adjusts the tracking to match the recorded tape.
Auto tracking engages in the following cases:
• When you insert the cassette and begin playback.
• When you press CH ' / " at the same time.
• When the Product has been playing back an unrecorded section of tape,
and then reaches a recorded tape segment.
Poor Tracking
Normal tracking
When auto tracking engages, “|” on the TV screen flashes for a few seconds.
• When a poorly recorded tape is played back, auto tracking may not operate normally. In this event, manually adjust
the tracking with CH ' / " to make any noise disappear.
Quick Start with Full Loading Mechanism
Your Product has a standby function (Full Loading Mechanism) to allow immediate recording and playback.
After pressing ÆREC or ûPLAY, it takes about 2 seconds until recording or playback is engaged when in the
standby mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
54
Playback
AUTO RENTAL
(This function only works when AUTO RENTAL mode on the MODE
selection screen is set to “ON”.)
The convenient auto rental mode lets you enjoy playback with ease.
When you insert a cassette with the erasure protection tab removed
(rental videos, etc.), your Product automatically turns on the power,
rewind the tape forward to find the recorded section, and plays back
the tape. When the tape reaches the end of recorded section, the
Product automatically rewinds the tape, ejects it and turns off the
power. If a DVD is being played back, the power will not turn off.
G-CODE
PROG
DV- NC70W
DV- NC70
DV- NC70X
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
1
2
3
4
Press VCR MENU to display the menu screen.
Press ' / " to select “MODE”.
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
TITLE
DVD MENU
Press SET to confirm.
CLEAR
RETURN
SET
ENTER
Press ' / " to select “AUTO RENTAL”.
ZERO BACK
SKIP SEARCH
COLOUR
AUTO PAL MESECAM NTSC
NTSC
3.58 4.43 PAL TV
BLUE BACK
AUTO RENTAL
REPEAT
NICAM
S.PICTURE
:SELECT
SET:ENTER
AUTO
ON
ON
AUTO
ON
:CHANGE
MENU:EXIT
OFF
OFF
OFF
OFF
OFF
AM/PM
INPUT SELECT VCR DVD
/
REV
FWD
PLAY
REC
PAUSE/STILL
5
6
Press \ / | to select “ON” or “OFF”.
STOP
TAPE
SPEED
DPSS
SKIP
Press SET to confirm and then press VCR MENU to return to
the normal screen.
SLOW
AUDIO
OUTPUT
CH
VCR
DVD
• If there is more than a 15 second unrecorded section between
recorded sections, the tape will automatically stop and rewind. To
watch the next recorded section, press ËSTOP, fast forward to that
section and play the tape.
• If the erasure protection hole is covered, press ûPLAY after the
power turns on automatically. (AUTO RENTAL Mode does not work.)
• The AUTO REPEAT mode has priority over the AUTO RENTAL mode. If
the AUTO REPEAT mode is set to “ON” and the video cassette
reaches its end, the Product will rewind the tape and play it back
again without ejecting the tape or turning off the power.
VCR/DVD COMBINATION
COLOUR
If the quality of a colour recording is poor, the picture may turn black
and white. In this event, set the COLOUR mode on the MODE
selection screen to PAL (fixed PAL colour mode), MESECAM (fixed
MESECAM colour mode), NTSC (fixed NTSC mode). Normally, the
colour mode should be set to “AUTO” mode. (See “Mode Selection”
on page 25.)
1
Follow steps 1 to 3 from “AUTO RENTAL” above.
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
55
Playback
2
Press ' / " to select “COLOUR”.
COLOUR
AUTO PAL MESECAM NTSC
NTSC 3.58 4.43 PAL TV
BLUE BACK
AUTO RENTAL
REPEAT
NICAM
S.PICTURE
AUTO
ON
ON
AUTO
ON
OFF
OFF
OFF
OFF
OFF
G-CODE
PROG
DV- NC70W
DV- NC70
DV- NC70X
:SELECT
SET:ENTER
:CHANGE
MENU:EXIT
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
ON
VCR/DVD VCR MENU
3
4
Press \ / | to select “AUTO”, “PAL”, “MESECAM” or “NTSC”.
SCREEN SELECTOR DVD SETUP
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
Press SET to confirm and then press VCR MENU to return to
the normal screen.
TITLE
DVD MENU
CLEAR
RETURN
SET
ENTER
• When the colour mode is set to fixed colour mode while the Product is
playing back a black and white tape or is receiving a black and white
broadcast, the picture may be coloured. In this event, set the
COLOUR mode on the MODE selection screen to “AUTO” mode.
ZERO BACK
SKIP SEARCH
AM/PM
INPUT SELECT VCR DVD
BLUE BACK
/
This function eliminates monitor noise and mutes sound during
playback of unrecorded portions of a tape, and when receiving a
non-broadcasting channel. A blue screen will also appear if the
Product is set to the Auxiliary input (LINE IN) mode but no video
signal is fed to the Product. (The BLUE BACK mode is set to “AUTO”
at the factory.)
REV
FWD
PLAY
REC
PAUSE/STILL
STOP
TAPE
SPEED
DPSS
SKIP
SLOW
1
2
Follow steps 1 to 3 from “AUTO RENTAL” on page 55.
AUDIO
OUTPUT
CH
VCR
DVD
Press ' / " to select “BLUE BACK”.
COLOUR
AUTO PAL MESECAM NTSC
NTSC
3.58 4.43 PAL TV
BLUE BACK
AUTO RENTAL
REPEAT
NICAM
S.PICTURE
AUTO
ON
ON
AUTO
ON
OFF
OFF
OFF
OFF
OFF
VCR/DVD COMBINATION
:SELECT
SET:ENTER
:CHANGE
MENU:EXIT
3
4
Press \ / | to select “AUTO” or “OFF”.
Press SET to confirm and then press VCR MENU to return to
the normal screen.
• Blue Back does not function during still picture, variable slow motion
and video search.
• Blue Back may not function properly if the broadcast signal is too
strong or too weak.
• Blue Back cannot be recorded.
•
If the antenna signal is weak while recording a TV programme, or if the
input signal is weak while tape dubbing, the monitor screen may turn
blue since the Product may not recognize whether or not a proper signal
is being received. In this event, set the BLUE BACK mode to “OFF”.
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
56
Playback
Playback of Hi-Fi Recorded Tapes
This Product will play back both video and audio, or audio-only
tapes recorded in the Hi-Fi mode.
G-CODE
PROG
DV- NC70W
• Stereo sound output is only possible using the AUDIO OUT terminals.
Sound from the radio frequency converter (RF OUT) is mono only. A
blue screen will appear if audio-only Hi-Fi tapes are played back.
DV- NC70
DV- NC70X
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
Audio Output Mode
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
The audio output mode is controlled by AUDIO OUTPUT on the
Remote. The Product is normally set to the Hi-Fi mode, with and
displayed on the VCR Front Panel display, and normal stereo sound
output.
Select , and only the Hi-Fi Left channel audio is heard from both
the Right and Left speakers.
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
TITLE
DVD MENU
CLEAR
RETURN
SET
ENTER
ZERO BACK
Select , and only the Hi-Fi Right channel audio is heard from both
the Right and Left speakers.
SKIP SEARCH
If you select the mono linear track, and will disappear.
AM/PM
INPUT SELECT VCR DVD
• Should the Hi-Fi output level be poor, the Product will automatically
select the mono linear track output.
• When playing back tapes which have only Hi-Fi sound recorded:
If Hi-Fi sound is not reproduced, or if there is some noise in the audio,
press CH ' / " until the sound improves.
/
REV
FWD
PLAY
REC
PAUSE/STILL
STOP
Adjusting Hi-Fi Audio Tracking
TAPE
SPEED
DPSS
SKIP
SLOW
(To adjust the Hi-Fi tracking manually when playing back a poorly
recorded Hi-Fi tape.)
• Normally you can simultaneously press and hold both CH ' / "
to obtain the optimal Hi-Fi audio tracking.
AUDIO
OUTPUT
CH
VCR
DVD
• If Hi-Fi audio is unstable (frequent dropouts, etc.) with a rental
video, a tape recorded on another VCR, restore normal tracking
while playing back the tape as described below:
VCR/DVD COMBINATION
1
Press ON SCREEN on the Remote and select the Full Display
mode. (See page 36.)
2
3
Simultaneously press CH ' / ".
Press CH ' / " repeatedly at equal, short intervals until the
and indicators disappear from the On Screen Display (OSD).
4
5
Press CH ' / " in the same manner while counting button
operations until the L and R indicators reappear and then
disappear again.
Press CH ' / " again for half the number of times counted in
step 4 above to obtain optimal track.
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
57
Sharp Super Picture
This function creates clearer picture quality only during playback.
1
2
Press VCR MENU to display the menu screen.
Select “MODE” with ' / " and then press SET to confirm.
MENU
G-CODE
PROG
DV- NC70W
G-CODE
TIMER
MODE
CHANNEL PRESET
CLOCK
DV- NC70
DV- NC70X
LANGUAGE
TIMER
:SELECT
SET:ENTER
OPERATE
DISPLAY
ON/OFF
EJECT
MENU:EXIT
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
3
Select “S.PICTURE” with ' / ". Then set it to “ON” or “OFF”
with \ / |.
ANGLE
TITLE
DVD MENU
COLOUR
AUTO PAL MESECAM NTSC
CLEAR
RETURN
SET
ENTER
NTSC
3.58 4.43 PAL TV
BLUE BACK
AUTO RENTAL
REPEAT
NICAM
S.PICTURE
AUTO
ON
ON
AUTO
ON
OFF
OFF
OFF
OFF
OFF
ZERO BACK
SKIP SEARCH
:SELECT
SET:ENTER
:CHANGE
MENU:EXIT
AM/PM
INPUT SELECT VCR DVD
ON:
/
Normally leave the mode set to ON. This high picture quality
function will create a clearer image during playback.
REV
FWD
PLAY
OFF:
Set to OFF when playing back a tape on the Product while
editing or when strong noise appears on the screen.
REC
PAUSE/STILL
STOP
TAPE
SPEED
DPSS
SKIP
SLOW
4
5
Press SET to confirm and return to the menu screen.
AUDIO
OUTPUT
CH
Press VCR MENU to exit to normal screen.
VCR
DVD
• This function only operates during playback. It will not operate when
recording or watching a TV program with the VCR tuner.
• When playing S-VHS tape:
1. Sharp Super Picture is set to off automatically. When finished
playback, the setting will return to the previous setting.
2. You cannot change ON/OFF setting manually.
• The ON/OFF status of the Sharp Super Picture can be checked when
ON SCREEN is pressed to display OSD.
VCR/DVD COMBINATION
• When the Product power is turned off, the Sharp Super Picture setting
is retained in memory.
• If power is interrupted for more than 60 minutes (power failure, etc.),
the setting will return to ON.
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
58
Auto Repeat
With this feature, the entire tape is played back repeatedly.
1
2
Press VCR MENU to display the menu screen.
G-CODE
PROG
Select “MODE” with ' / " and then press SET to confirm.
DV- NC70W
DV- NC70
DV- NC70X
MENU
G-CODE
TIMER
MODE
CHANNEL PRESET
CLOCK
LANGUAGE
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
:SELECT
SET:ENTER
MENU:EXIT
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
TITLE
DVD MENU
3
Select “REPEAT” with ' / ". Then set the mode to “ON” or
“OFF” with \ / |.
CLEAR
RETURN
SET
ENTER
COLOUR
AUTO PAL MESECAM NTSC
ZERO BACK
NTSC
3.58 4.43 PAL TV
SKIP SEARCH
BLUE BACK
AUTO RENTAL
REPEAT
NICAM
S.PICTURE
:SELECT
SET:ENTER
AUTO
ON
ON
AUTO
ON
OFF
OFF
OFF
OFF
OFF
AM/PM
INPUT SELECT VCR DVD
:CHANGE
MENU:EXIT
/
REV
FWD
4
5
Press SET to confirm and return to the menu screen.
PLAY
REC
PAUSE/STILL
Press VCR MENU to return to normal screen.
STOP
TAPE
SPEED
DPSS
SKIP
SLOW
• “REPEAT” will be displayed on the OSD when the Auto Repeat mode
is “ON”.
AUDIO
OUTPUT
CH
• If the Auto Repeat is “ON” and the tape is rewinded to the beginning
with rewind or reverse video search, the tape will automatically start
playback.
VCR
DVD
VCR/DVD COMBINATION
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
59
Auto Zero Back
The zero-back function makes the cassette fast forward (or rewind)
to the previously set “0:00.00” point and stop there.
1
2
3
Make sure the counter is displayed, then press CLEAR on the
Remote at the point you wish to return and later “0:00.00” is
displayed.
G-CODE
PROG
DV- NC70W
DV- NC70
DV- NC70X
Press ZERO BACK on the Remote. The Product automatically
detects the direction of the “0:00.00” position and fast forwards
(or rewinds) the tape.
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
When the tape reaches the “0:00.00” position, the tape
automatically stops.
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
TITLE
DVD MENU
• The zero-back function does not operate during recording and fast
forward (or rewind). The function works during the playback, stop and
video search modes.
CLEAR
RETURN
SET
ENTER
ZERO BACK
SKIP SEARCH
AM/PM
INPUT SELECT VCR DVD
/
REV
FWD
PLAY
REC
PAUSE/STILL
STOP
TAPE
SPEED
DPSS
SKIP
SLOW
AUDIO
OUTPUT
CH
VCR
DVD
VCR/DVD COMBINATION
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
60
DPSS (Digital Program Search System)/Skip Search
DPSS
With this feature you can quickly locate a desired section of the tape.
The DPSS feature makes use of index signals to search for a
specified tape segment and begin playback automatically.
G-CODE
PROG
DV- NC70W
Index signal
DV- NC70
DV- NC70X
An index signal is automatically recorded on the tape at the start of
ordinary recording, simple recording timer and timer recording.
Current tape position
TIMER
OPERATE
DISPLAY
Rewind
Fast forward
ON/OFF
EJECT
-1
1
2
3
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
Index signals
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
1
2
Load a tape containing index signals into the Product.
TITLE
DVD MENU
Select the index number of the desired programme using DPSS
on the Remote. Search starts immediately. (When a signal is
located, the displayed number decreases.)
CLEAR
RETURN
SET
ENTER
ZERO BACK
3
When the selected index signal-encoded section is found,
playback begins automatically.
SKIP SEARCH
AM/PM
INPUT SELECT VCR DVD
• DPSS may not function properly if the index signals are too close
together (within 8 minutes of each other).
• DPSS can be cancelled with ûPLAY or ËSTOP.
• If the tape reaches its end or is rewinded completely before locating
the desired index signal, DPSS is cancelled.
/
REV
FWD
PLAY
REC
PAUSE/STILL
• DPSS may not function for damaged or worn tapes.
STOP
•
The DPSS function cannot be used with tapes that contain no index signals.
• The starting point of a programme may vary slightly.
• DPSS does not operate during the slow, record, fast forward, rewind,
timer standby, and timer recording modes, or when there is no
cassette loaded.
TAPE
SPEED
DPSS
SKIP
SLOW
AUDIO
OUTPUT
CH
VCR
DVD
Skip Search
When SKIP SEARCH on the Remote is pressed during playback
mode, the product will perform a forward video search for a fixed
interval of playback time before resuming playback. Depending on
how many times the button is pressed, it is possible to set the
forward video search time to approx. 30, 60, 90 or 120 seconds of
recorded material.
VCR/DVD COMBINATION
Number of Times Pressed
Forward Video Search Time
Approx. 30 sec.
(of playback time)
1 time
Approx. 60 sec.
(of playback time)
2 times
3 times
4 times
Approx. 90 sec.
(of playback time)
Approx. 120 sec.
(of playback time)
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
61
TV Programme Recording
Cassette Erase Protection
ERASURE
PROTECTION TAB
A
cassette has a removable tab to prevent accidental
,
PAL SECAM
erasure of recorded material. Removing the tab prevents recording.
To record on a video cassette with the tab removed, place adhesive
tape over the tab opening.
Recording a TV Programme
G-CODE
PROG
Preparation
DV- NC70W
• Press OPERATE. Then move the VCR/DVD CHANGE Switch to
VCR.
DV- NC70
DV- NC70X
• Ensure the Video channel is selected on the TV.
TIMER
OPERATE
DISPLAY
1
Insert the cassette, making sure the erasure protection hole is
covered.
ON/OFF
EJECT
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
2
3
Select the channel position you wish to record with CH '/ ".
ANGLE
TITLE
DVD MENU
Select the SP (Standard Play), EP (Extended Play) or LP (Long
Play) recording speed with TAPE SPEED on the Remote (“SP”,
“EP” or “LP” will light up on the VCR Front Panel display.) SP
(Standard Play) gives the best picture quality, EP (Extended
Play) gives the triple recording time and LP (Long Play) gives
the double recording time.
CLEAR
RETURN
SET
ENTER
ZERO BACK
SKIP SEARCH
• If the COLOUR mode is set to “AUTO” or “MESECAM”, when a
SECAM signal is received and the EP mode is selected, the Product
will automatically change the EP mode to LP mode.
AM/PM
INPUT SELECT VCR DVD
/
REV
FWD
PLAY
4
5
Press ÆREC. (If the erasure protection hole is uncovered, the
cassette will be ejected.) To pause during recording, press
âPAUSE/STILL. To resume recording, press âPAUSE/STILL
again.
REC
PAUSE/STILL
STOP
TAPE
SPEED
DPSS
SKIP
SLOW
To stop recording, press ËSTOP.
AUDIO
OUTPUT
CH
VCR
DVD
• The pause mode disengages automatically after about 5 minutes, and
the Product enters stop mode.
• To record audio and video from an external source through the
AUDIO/VIDEO terminal on the rear of the Product, press INPUT SELECT
on the Remote to select the AV channel position situated between the
last channel and first channel. (When the AV position is selected, “L1”
or “L2” is displayed where a channel position number is usually
displayed.)
VCR/DVD COMBINATION
• If the TV signals are weak and the picture changes to monochrome,
set the strict colour mode on the MODE selection screen. (See ”Mode
Selection” on page 23.) Normally, the colour mode should be set to
“AUTO”.
To Watch Another TV Programme While
Recording
After steps 1 to 4 have been completed, select the programme you
wish to view using the TV tuner. At the end of the tape, your Product
will automatically stop recording, rewind the tape, eject it and then turn
off the power. If a DVD is being played back, the power will not turn off.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
62
TV Programme Recording
Recording NICAM/IGR Multiplex Broadcasts
This Product is capable of receiving NICAM multiplex broadcasts (PAL-I, B/G, D/K) and IGR multiplex broad-
casts (PAL-B/G, D/K). NICAM multiplex broadcasts will be recorded in stereo/bilingual when the NICAM setting on the
OSD’s MODE is set to AUTO. For information on how to carry out NICAM setting (See “Mode Selection” on page 25).
IGR multiplex broadcasts will be recorded on stereo/bilingual. (The AUTO/OFF setting will not function.) This Product
automatically records on two types of audio track.
Hi-Fi track:
Special rotary heads will be used to record an audio signal deep in the video track in Hi-Fi. Multiplex broad-
casts fall into “stereo” and “bilingual” broadcasts and they will be automatically recorded on their respective
tracks.
Normal track:
Conventional analogue audio is always recorded on the normal track (mono sound) regardless of whether your
Product is receiving a multiplex broadcasts or not.
Setting of “NICAM” in MODE
AUTO position
OFF position
Broadcast
Hi-Fi track
Normal track
Hi-Fi track
Normal track
Normal sound
(mono sound)
mono
sound
mono
sound
mono
sound
mono
sound
NICAM sound
(bilingual)
mono
sound
mono
sound
mono
sound
NICAM (bilingual)
NICAM (stereo)
IGR (bilingual)
NICAM sound
(stereo)
mono
sound
mono
sound
mono
sound
IGR sound
(bilingual)
mono
sound
IGR sound
(bilingual)
mono
sound
mono
sound
IGR sound
(stereo)
IGR sound
(stereo)
mono
sound
IGR (stereo)
On screen display
Broadcast
• When receiving a stereo multiplex broadcast,
NICAM
IGR
TYPE
(LR) will be indicated on the on screen display.
• When receiving a bilingual multiplex broadcast,
will be displayed on the on screen display.
/
Stereo
Bilingual
• There are tapes, though small in number, which have a normal track that has been divided into two tracks. On such
tapes, stereo as well as bilingual audio are recorded on the normal track. If such a tape is played back on your
Product, the tape’s stereo sound will be reproduced in monaural and its bilingual in both languages combined.
• When a cassette tape on which a NICAM multiplex broadcast has been recorded in stereo or bilingual mode is played
back by a VCR that is not a Hi-Fi VCR, only the sound on the normal track will be reproduced.
• When you select “OFF” for NICAM in the OSD MODE, the stereo and bilingual audio of a NICAM multiplex broadcast
will be fixed to the normal sound.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
63
Simple Recording Timer
Immediate Recording
This is convenient function when having an unexpected visitor or
telephone call.
G-CODE
PROG
1
Select the channel position to be recorded with CH '/ ".
(Example) Channel position 2
DV- NC70W
DV- NC70
DV- NC70X
2
S.PICTURE ON
I/
II
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
SP
L R
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
REPEAT
8:00
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
15/12 00
0:00.00
TITLE
DVD MENU
CLEAR
RETURN
SET
ENTER
2
Press ÆREC to enter the normal recording mode. Then, press
ÆREC repeatedly to set the desired ending time.
(Example) Ending time 9:30
ZERO BACK
SKIP SEARCH
2
S.PICTURE ON
I/
II
AM/PM
INPUT SELECT VCR DVD
SP
STOP
9:30
L R
/
REV
FWD
PLAY
8:00
15/12 00
0:00.00
REC
PAUSE/STILL
STOP
TAPE
SPEED
DPSS
SKIP
SLOW
• Each press of ÆREC increases the stop time by 10 minutes.
• Press ËSTOP to terminate recording.
AUDIO
OUTPUT
CH
VCR
DVD
VCR/DVD COMBINATION
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
64
Programming the Timer with G-CODE® System (DV-NC70W only)
This product has the G-CODE programming system. By simply inputting
the G-CODE number with the number buttons, you can programme your
Product timer recording.
The G-CODE numbers are listed in most newspaper, TV guide, and
local cable TV listings.
The timer can be set for automatic recording of up to 8 events over a
G-CODE
DV- NC70W
365 day period. In addition, each of the events can be set to be
recorded on a daily or weekly basis up to the limit of the tape.
PROG
DV- NC70
DV- NC70X
Preparation
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
• Load the cassette, ensuring the erasure protection hole is covered.
The Product power will automatically turn on.
• Check that the clock is displaying the correct time.
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
TITLE
DVD MENU
1
Press VCR MENU. Then select “G-CODE” with ' / "and press
SET to confirm.
CLEAR
RETURN
SET
ENTER
MENU
ZERO BACK
G-CODE
TIMER
MODE
SKIP SEARCH
CHANNEL PRESET
CLOCK
LANGUAGE
AM/PM
INPUT SELECT VCR DVD
:SELECT
SET:ENTER
/
MENU:EXIT
REV
FWD
PLAY
2
Set the G-CODE number with the number buttons (0 to 9).
REC
PAUSE/STILL
STOP
G-CODE NO.
ONCE
-
TAPE
SPEED
DPSS
SKIP
SLOW
WEEKLY DAILY
AUDIO
OUTPUT
CH
VCR
DVD
:SELECT
SET:ENTER
MENU:EXIT
• For the G-CODE number, refer to your newspaper or TV guide.
• Press the G-CODE button on the Remote to directly select this screen.
VCR/DVD COMBINATION
3
If you want to record only once, press SET and go to step 4.
Otherwise, press '/ " to select daily/weekly setting mode and
select “DAILY” or “WEEKLY” with \/ |. Then press SET to confirm.
G-CODE NO.
1234
ONCE WEEKLY DAILY
:SELECT
SET:ENTER
:CHANGE
MENU:EXIT
• “ONCE”: To record only once.
• “WEEKLY”: To record every week at the same time.
• “DAILY”: To record every day at the same time.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
65
®
Programming the Timer with G-CODE System
4
If you are going to record a programme from a station which
does not have the PR number programmed, (“ --” is displayed)
set that number to be the same as the PR number to which your
broadcasting channel is set into. (See Note on page 67.) Use
the number buttons (0 to 9) or '/ ". Then press | .
(Ex.: 47)
G-CODE
PROG
DV- NC70W
DV- NC70
DV- NC70X
1/2
DATE
PR START STOP
15/12 47 12:00
PM
12:30
PM
SP
--/-- --
--/-- --
--/-- --
-:--
-:--
-:--
-:-- --
-:-- --
-:-- --
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
ON
VCR/DVD VCR MENU
PR :PRESET CH
:SELECT
SET:ENTER
SCREEN SELECTOR DVD SETUP
:CHANGE
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
MENU:EXIT
ANGLE
TITLE
DVD MENU
5
Select the tape speed with '/ ".
CLEAR
RETURN
SET
ENTER
1/2
SP
DATE
15/12 47 12:00
PR START STOP
ZERO BACK
PM
12:30
PM
--/-- --
--/-- --
--/-- --
-:--
-:--
-:--
-:-- --
-:-- --
-:-- --
SKIP SEARCH
SP/LP.EP:TAPE SPEED
:SELECT
SET:ENTER
:CHANGE
MENU:EXIT
AM/PM
INPUT SELECT VCR DVD
/
REV
FWD
PLAY
• If the COLOUR mode is set to “AUTO” or “MESECAM”, when a
SECAM signal is received and the EP mode is selected, the Product
will automatically change the EP mode to LP mode.
• A tape recorded in the PAL EP (Extended Play) mode can only be
playback in a VCR which have its same function (PAL EP (Extended
Play) mode).
REC
PAUSE/STILL
STOP
TAPE
SPEED
DPSS
SKIP
SLOW
AUDIO
OUTPUT
CH
• For best result, it is advisable to Playback or Recording EP mode with
this Product.
VCR
DVD
6
Press SET.
VCR/DVD COMBINATION
G-CODE NO.
ONCE
-
WEEKLY DAILY
:SELECT
SET:ENTER
MENU:EXIT
• To programme additional timer settings, press SET and repeat steps 2
and 6.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
66
®
Programming the Timer with G-CODE System
7
8
Press VCR MENU to return to the normal screen.
To set the product for automatic timer recording, press TIMER
ON/OFF and ensure the “ ” lights on the VCR Front Panel
display.
G-CODE
DV- NC70W
PROG
DV- NC70
DV- NC70X
VCR
—
L R
SEPVP D
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
• Please be sure to check that the start and end times of two different
programmes do not overlap, as the remote control has been designed
to accept the basic individual G-CODE number only. If the recording
periods of two programmes overlap, the beginning of the second
programme will not be recorded.
TITLE
DVD MENU
CLEAR
RETURN
SET
ENTER
ZERO BACK
• To cancel the programmed G-CODE setting, select the TIMER setting
mode on the menu screen. Then select the programme number you
wish to cancel with '/ "and press CLEAR. (See “Cancelling Timer
Programmes” on page 72.)
SKIP SEARCH
AM/PM
INPUT SELECT VCR DVD
/
Setting the Programme Number In Step 4
REV
FWD
When using the G-CODE system for the first time the Programme
number (PR) on the screen shows two dashes and is highlighted
white. Set it to be the same as the PR number to which your broad-
casting channel is set into.
PLAY
REC
PAUSE/STILL
STOP
For instance if you can view CH 47 on programme (PR) 47, set the
On screen PR number to 47.
• You need to set this only once.
TAPE
SPEED
DPSS
SKIP
SLOW
AUDIO
OUTPUT
CH
• If the channels are retuned you need to set the PR numbers again.
VCR
DVD
PR: Preset Channel
1/2
DATE
15/12 -- 12:00
PR START STOP
VCR/DVD COMBINATION
PM
12:30
PM
SP
--/-- --
--/-- --
--/-- --
-:--
-:--
-:--
-:-- --
-:-- --
-:-- --
PR :PRESET CH
:SELECT
:CHANGE
SET:ENTER
MENU:EXIT
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
67
Recording with the Timer
The timer can be set manually for automatic recording of up to 8
events over a 365 day period.
Preparation
• Load the cassette, ensuring the erasure protection hole is covered.
The Product power will automatically turn on.
• Check that the clock is displaying the correct time. (See “Setting the
Clock” on page 35.)
G-CODE
PROG
DV- NC70W
DV- NC70
DV- NC70X
• Be sure that the colour mode is set to “AUTO”. (See “COLOUR” on
page 55.)
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
For DV-NC70 and DV-NC70X model:
Press PROG on the Remote to enter the Timer setting screen.
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
1
2
Press VCR MENU. Then select “TIMER” with '/ "and press
SET.
TITLE
DVD MENU
CLEAR
RETURN
SET
ENTER
MENU
G-CODE
TIMER
MODE
CHANNEL PRESET
CLOCK
ZERO BACK
SKIP SEARCH
LANGUAGE
:SELECT
AM/PM
INPUT SELECT VCR DVD
SET:ENTER
MENU:EXIT
/
REV
FWD
Select the timer position with '/ "and press SET.
• If the timer positions 1 to 4 have already been set, the screen
changes to 2/2 (timer positions 5 to 8).
PLAY
REC
PAUSE/STILL
STOP
1/2
DATE
PR START STOP
TAPE
SPEED
DPSS
SKIP
SLOW
--/-- --
--/-- --
--/-- --
--/-- --
-:--
-:--
-:--
-:--
2/2
-:-- --
-:-- --
-:-- --
-:-- --
AUDIO
OUTPUT
CH
VCR
DVD
:SELECT
SET:ENTER
MENU:EXIT
3
Set the date for timer recording with the number buttons (0 to 9)
or '/ "on the Remote and press |.
VCR/DVD COMBINATION
• First set the “day” digits and then “month”. If there is only one
“day” or one “month” digit, enter a 0 first.
1/2
DATE
PR START STOP
15/12 --
--/-- --
--/-- --
--/-- --
-:--
-:--
-:--
-:--
-:-- SP
-:-- --
-:-- --
-:-- --
“SP” will be displayed
automatically.
DATE :DAY/MONTH
:SELECT
:CHANGE
SET:ENTER
MENU:EXIT
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
68
Recording with the Timer
4
If you want to record only once, press | and go to step 5.
Otherwise, select “D (DAILY)” to record at the same time each
day or “W (WEEKLY)” to record at the same time each week with
'/ ", and then pressing |.
G-CODE
DV- NC70W
1/2
PROG
DV- NC70
DV- NC70X
DATE
PR START STOP
15/12 --
--/-- --
--/-- --
--/-- --
:ONCE
W:WEEKLY
:SELECT
SET:ENTER
-:--
-:--
-:--
-:--
-:-- SP
-:-- --
-:-- --
-:-- --
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
D:DAILY
:CHANGE
MENU:EXIT
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
5
Set the channel number using the number buttons (0 to 9) or
'/ "and press |.
TITLE
DVD MENU
• To record audio and video from an external source through an
AUDIO/VIDEO terminal on the Product. Press '/ "to select an
AV channel.
(When an AV position is selected, “L1” or “L2” is displayed where
a channel position number is usually displayed.)
CLEAR
RETURN
SET
ENTER
ZERO BACK
SKIP SEARCH
1/2
DATE
15/12 471 -:--
--/-- --
--/-- --
--/-- --
PR START STOP
AM/PM
INPUT SELECT VCR DVD
PM
-:-- SP
-:-- --
-:-- --
-:-- --
/
-:--
-:--
-:--
REV
FWD
PLAY
REC
PAUSE/STILL
STOP
• '/ "can also be used to set the date and time instead of the
number buttons (0 to 9).
TAPE
SPEED
DPSS
SKIP
SLOW
• Press 0 first if the day, month, hour or minute is a single digit.
AUDIO
OUTPUT
CH
6
7
Set the start time with the number buttons (0 to 9) or '/ " and
press |.
VCR
DVD
1/2
DATE
PR START STOP
15/12 47 12:00
PM
-:-- SP
-:-- --
-:-- --
-:-- --
VCR/DVD COMBINATION
--/-- --
--/-- --
--/-- --
-:--
-:--
-:--
When the clock is set to 24H mode,
AM/PM indicator will not appear
Set the stop time with the number buttons (0 to 9) or '/ "and
press |.
1/2
DATE
PR START STOP
15/12 47 12:00
PM
12:30
PM
SP
--/-- --
--/-- --
--/-- --
-:--
-:--
-:--
-:-- --
-:-- --
-:-- --
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
69
Recording with the Timer
8
9
Select the speed with '/ ".
1/2
SP
-:-- --
-:-- --
-:-- --
DATE
PR START STOP
15/12 47 12:00
PM
12:30
PM
--/-- --
--/-- --
--/-- --
-:--
-:--
-:--
G-CODE
PROG
DV- NC70W
DV- NC70
DV- NC70X
• SP: Standard Play, LP: Long Play, EP: Extended Play
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
Press SET. To programme additional timer settings, repeat steps
3 through 8.
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
TITLE
DVD MENU
1/2
DATE
PR START STOP
15/12 47 12:00
PM
12:30
PM
SP
CLEAR
RETURN
SET
--/-- --
--/-- --
--/-- --
-:--
-:--
-:--
2/2
-:-- --
-:-- --
-:-- --
ENTER
ZERO BACK
CLEAR:CANCEL
:SELECT
SKIP SEARCH
SET:ENTER
MENU:EXIT
10 Press VCR MENU to return to the normal screen.
AM/PM
INPUT SELECT VCR DVD
/
REV
FWD
11 To set the product for automatic timer recording, press TIMER
ON/OFF and ensure the “ ” lights on the VCR Front Panel
display.
PLAY
REC
PAUSE/STILL
STOP
VCR
VCR
TAPE
SPEED
DPSS
SKIP
L R
SLOW
SEPVP D
AUDIO
OUTPUT
CH
VCR
DVD
• If the timer recording is finished, your product will stop and turn off
automatically. (In this case the cassette is not ejected.)
If a DVD is being played back, the power will not turn off. (The timer
recording is stopped while the power stays on.)
• If the cassette runs out during the timer recording, your product will
eject the cassette without rewinding.
VCR/DVD COMBINATION
In this case, the timer recording is cancelled (
“
”
disappears) and
the device turns itself off automatically. However, if a DVD is being
played back, the power will not turn off. (The power stays on.)
• If power is interrupted for more than 60 minutes (power failure, etc.),
all timer settings will be cancelled.
• If TIMER ON/OFF is pressed when there is no cassette loaded, “
”
flashes for 5 seconds, indicating that timer recording is not possible.
• If TIMER ON/OFF is pressed while a cassette with an uncovered
erasure protection hole is loaded, “ ” flashes and the cassette is ejected.
• When “
” is lit, regular VCR operation, clock setting and setting/
cancelling/confirming timer positions are not possible. For regular VCR
operation, clock setting and setting/cancelling/confirming timer
positions, press TIMER ON/OFF to disengage the timer (“
disappears), and then turn on your Product.
”
• During timer recording, the timer cannot be set.
• To terminate timer recording, press ËSTOP during timer recording.
• If the same time is input for the start time and the stop time, the timer
setting will be cancelled.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
70
Recording with the Timer
Confirming Timer Programmes
You can see on the On Screen Display a list of all timer programmes
that are already set.
G-CODE
Preparation
DV- NC70W
• Press OPERATE. Then move the VCR/DVD CHANGE Switch to
VCR and select the video channel on the TV.
PROG
DV- NC70
DV- NC70X
1
2
Press VCR MENU. (If the “ ” indicator on the VCR Front Panel
display is lit, cancel the timer standby mode with TIMER ON/OFF
and then turn on the power.)
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
Select “TIMER” with '/ "and then press SET to confirm .
ANGLE
TITLE
DVD MENU
MENU
G-CODE
TIMER
CLEAR
RETURN
SET
ENTER
MODE
CHANNEL PRESET
CLOCK
ZERO BACK
LANGUAGE
SKIP SEARCH
:SELECT
SET:ENTER
MENU:EXIT
AM/PM
INPUT SELECT VCR DVD
3
The screen for confirming programmes that have been set will
appear.
/
REV
FWD
PLAY
1/2
DATE
15/12 47 12:00
--/-- --
--/-- --
--/-- --
PR START STOP
REC
PAUSE/STILL
PM
12:30
PM
SP
STOP
-:--
-:--
-:--
2/2
-:-- --
-:-- --
-:-- --
TAPE
SPEED
DPSS
SKIP
SLOW
AUDIO
OUTPUT
CH
:SELECT
SET:ENTER
MENU:EXIT
VCR
DVD
• Check the information displayed.
•
If you want to correct the data, select the programme to be
changed with '/ "and press SET. Correct the setting as
described on pages 72.
VCR/DVD COMBINATION
•
After the data is changed, press SET at the applicable tape-speed
position at right.
4
Press VCR MENU to return to the normal screen.
• After checking or correcting the programme contents, press
TIMER ON/OFF to enter the Timer Standby mode.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
71
Recording with the Timer
Cancelling Timer Programmes
Perform the following procedure to cancel timer programmes that
have already been set.
G-CODE
PROG
DV- NC70W
Preparation
DV- NC70
DV- NC70X
• Press OPERATE. Then move the VCR/DVD CHANGE Switch to
VCR and select the video channel on the TV.
1
2
Press VCR MENU. (If the “ ” indicator on the VCR Front Panel
display is lit, cancel the timer standby mode with TIMER ON/OFF
and then turn on the power.)
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
Select “TIMER” with '/ "and then press SET to confirm .
TITLE
DVD MENU
MENU
CLEAR
RETURN
SET
ENTER
G-CODE
TIMER
MODE
CHANNEL PRESET
CLOCK
ZERO BACK
LANGUAGE
SKIP SEARCH
:SELECT
SET:ENTER
MENU:EXIT
AM/PM
INPUT SELECT VCR DVD
/
3
The screen for confirming programmes that have been set will
appear.
REV
FWD
• Select the programme you wish to cancel with '/ ".
(The selected programme will appear highlighted.)
PLAY
REC
PAUSE/STILL
STOP
1/2
DATE
15/12 48 12:00
--/-- --
--/-- --
--/-- --
PR START STOP
TAPE
SPEED
DPSS
SKIP
PM
12:30
PM
SP
SLOW
-:--
-:--
-:--
2/2
-:-- --
-:-- --
-:-- --
AUDIO
OUTPUT
CH
VCR
DVD
:SELECT
SET:ENTER
MENU:EXIT
4
5
Double-check that it is the programme you wish to cancel, and
press CLEAR. It will be cleared on the screen.
VCR/DVD COMBINATION
1/2
2/2
DATE
PR START STOP
--/-- --
--/-- --
--/-- --
--/-- --
-:--
-:--
-:--
-:--
-:-- --
-:-- --
-:-- --
-:-- --
:SELECT
SET:ENTER
MENU:EXIT
Press VCR MENU to return to the normal screen.
• If there are still some programmes to be set, press TIMER
ON/OFF to enter the Timer Standby mode.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
72
Tape Dubbing
G-CODE
PROG
DV- NC70W
Tape Dubbing Connection Instructions
DV- NC70
DV- NC70X
Your product can dub (copy) video material from another video
device. It can also output video and audio signals for recording on
other video or audio equipment. Audio/Video dubbing cannot be
done separately.
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
1
2
Switch your product to the auxiliary input by pressing INPUT
SELECT. “L1” lights up on the VCR Front Panel display. (You
can also use CH '/ ".)
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
TITLE
DVD MENU
Begin recording on the dubbing VCR and playback on the
source VCR simultaneously.
CLEAR
RETURN
SET
ENTER
ZERO BACK
SKIP SEARCH
• When using special playback functions (still picture, video search,
frame advance, and variable slow motion) during dubbing, a blue
screen may appear.
Set BLUE SCREEN mode on the dubbing VCR (for recording) to OFF.
(See Mode Selection on page 25.)
AM/PM
INPUT SELECT VCR DVD
/
• Use an RCA pin–type connection cable (not supplied with VCR, but
supplied with VIEWCAM) to connect source VCR to dubbing VCR.
• Refer to the manual of the VCR connected to this product when
dubbing a tape.
• You can also use the front AV jacks. Select “L2” (Aux. 2 input) by
pressing INPUT SELECT twice.
REV
FWD
PLAY
REC
PAUSE/STILL
STOP
• If source VCR is a monaural mode, connect the audio cable to
“AUDIO-L” of the dubbing VCR.
TAPE
SPEED
DPSS
SKIP
SLOW
AUDIO
OUTPUT
CH
VCR
DVD
VCR/DVD COMBINATION
Sharp Viewcam
(for playback)
Audio/Video
cable (supplied
with Viewcam)
DVD/VCR
VCR
ANTENNA IN
DVD/VCR
VCR
ANTENNA IN
AV 2 IN VIDEO L(MONO) - AUDIO-R
LINE OUT
1
LINE IN 1
LINE OUT
1
LINE IN 1
R
R
AUDIO
L
R
AUDIO
L
or
AUDIO
L
AUDIO
RF OUT
RF OUT
VIDEO
VIDEO
VIDEO
VIDEO
To Front
Source VCR
(for playback)
Dubbing VCR
(for recording)
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
73
Recording a DVD Disc onto a Video Cassette
Use the following procedure to record the images and sounds on a
DVD disc onto a video cassette.
OPERATE EJECT/STOP
REW PLAY/×2
PLAY
STOP
OPEN/CLOSE
REC
/
TIMER
VCR/DVD
SELECTOR
Recording a DVD disc onto a Video cassette
(Tape Editing mode)
CH
VCR DVD
(
L
)
-
AV
2
I
N
V
I
D
E
O
MONO AUDIO R
-
Preparation
PLAY
OPERATE
VCR DVD indicator
TV
• Turn on the TV and switch to the external “VIDEO” or “AV” channel.
G-CODE
DV- NC70W
PROG
DV- NC70
DV- NC70X
This Product
• Press OPERATE.
• Move the VCR/DVD CHANGE Switch on the Remote to VCR.
TIMER
ON/OFF
OPERATE
EJECT
ON
VCR/DVD VCR MENU
DISPLAY
SCREEN SELECTOR DVD SETUP
1
2
Insert both the DVD disc and the video cassette for recording.
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
TITLE
DVD MENU
Press VCR \DVD.
• The VCR \DVD indicator lights up.
CLEAR
RETURN
SET
ENTER
ZERO BACK
3
4
Move the VCR/DVD CHANGE Switch on the Remote to DVD.
SKIP SEARCH
Press ON SCREEN to turn off the DVD on screen display (See
page 49).
AM/PM
INPUT SELECT VCR DVD
/
REV
FWD
5
Press ûPLAY.
• The disc start playback.
PLAY
REC
PAUSE/STILL
STOP
TAPE
SPEED
DPSS
SKIP
• In DVD to VCR recording mode, some discs cannot be recorded:
1Discs with copy guard function
SLOW
AUDIO
OUTPUT
CH
VCR
DVD
VCR/DVD COMBINATION
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
74
Recording a DVD Disc onto a Video Cassette
6
Press
ÆREC.
• The images on the DVD disc are recorded onto the VCR
cassette.
G-CODE
DV- NC70W
• When the VCR is in stop mode, the channel returns to the previ-
ously received channel.
PROG
DV- NC70
DV- NC70X
• The VCR/DVD SELECTOR is fixed to VCR in the Tape Editing
mode (VCR\ DVD indicator lights up).
• Operate the VCR/DVD SELECTOR after pressing VCR\DVD,
and after the Tape Editing mode has been cleared (VCR\ DVD
indicator stops lighting up).
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
TITLE
DVD MENU
• The following are not signs of trouble.
CLEAR
RETURN
SET
ENTER
1The brightness of images from regular DVD disc playback and
from discs played in Tape Editing mode might vary.
2The discs playing time and the Real time counter slightly vary when
recording.
ZERO BACK
SKIP SEARCH
• The DVD/VCR output jacks become VCR fixed.
• The following operations cancel the DVD/VCR output and return to the
regular external input.
AM/PM
INPUT SELECT VCR DVD
1Programming the timer.
/
2Setting the recording ending time during Pause.
3Turning OPERATE on or off after entering the Tape Editing mode.
• Copy protected DVD discs cannot be recorded (The image will be
distorted, when ÆREC is pressed).
REV
FWD
PLAY
• If the DVD on screen display is “ON” while recording, the display will
also be recorded.
REC
PAUSE/STILL
STOP
TAPE
SPEED
DPSS
SKIP
SLOW
The recordings, which you make from TV/radio broadcasts or audio
sources (such as records) are for your own private use, and cannot be
used without prior permission or consent of the author.
AUDIO
OUTPUT
CH
VCR
DVD
VCR/DVD COMBINATION
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
75
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
76
Watching the DVD
Preparing to Use DVD..................................................................... 78
When connecting a TV with the DVD output Jacks ....................... 78
When connecting a TV with the DVD/VCR shared output jacks .... 78
Playback .......................................................................................... 79
Basic Play ...................................................................................... 79
Track Direct Playback .................................................................... 79
Fast Forward/Fast Reverse ........................................................... 80
Slow-Motion Play ........................................................................... 80
Still/Pause ...................................................................................... 81
Frame Advance.............................................................................. 81
Skip (Forward/Reverse) ................................................................. 81
Angle Selection ............................................................................... 82
Playing MP3 Discs .......................................................................... 83
Regarding MP3 discs..................................................................... 83
Playing MP3 discs.......................................................................... 83
To play MP3 discs .......................................................................... 84
To play another file (music title) while playing................................ 84
To skip the file while playing........................................................... 84
About the Function Control Screen .............................................. 85
Direct skip (title [track]/chapter/time).............................................. 86
Subtitle language setting................................................................ 87
Angle setting .................................................................................. 88
Audio setting .................................................................................. 89
3D VIRTUAL SURROUND setting ................................................. 90
DIGITAL GAMMA setting ............................................................... 91
Direct Selection of Scenes ............................................................. 92
Selecting Scenes by Title Number ................................................. 92
Selecting Scenes from the Menu Screen....................................... 92
Programmed Playback ................................................................... 93
Chapter Programmed Playback ..................................................... 93
Track Programmed Playback......................................................... 94
MP3 Files Programmed Playback.................................................. 95
Repeat Playback ............................................................................. 96
Repeat playback ............................................................................ 96
A-B Repeat .................................................................................... 97
Resume Function ............................................................................ 98
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
77
Preparing to Use DVD
The following steps are necessary to display the DVD screen on the
TV.
When connecting a TV with the DVD output
jacks
OPERATE EJECT/STOP
REW PLAY/×
2
PLAY
STOP
OPEN/CLOSE
REC
/
TIMER
VCR/DVD
SELECTOR
CH
VCR DVD
(
)
-
AV
2
IN VIDEO
L
MONO AUDIO R
-
1
2
Turn on the TV and switch the TV channel to the external input
“VIDEO” or “AV” channel connected to DVD output jack.
VCR/DVD
SELECTOR
OPERATE
VCR/DVD
SELECTOR
Press OPERATE.
• The start up screen is displayed on the TV screen.
G-CODE
PROG
DV- NC70W
DV- NC70
DV- NC70X
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
3
Move VCR/DVD CHANGE Switch on the Remote to DVD.
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
VCR
DVD
ANGLE
TITLE
DVD MENU
CLEAR
RETURN
SET
ENTER
• When the TV is connected to the DVD output jack, the image will be
displayed regardless of the VCR/DVD mode selected. Therefore, it is
not necessary to adjust the mode selected.
ZERO BACK
SKIP SEARCH
AM/PM
INPUT SELECT VCR DVD
When connecting a TV with the DVD/VCR
shared output jacks
/
REV
FWD
1
Turn on the TV and switch the TV channel to the external input
“VIDEO” or “AV” channel connected to DVD/VCR shared output
jack.
PLAY
REC
PAUSE/STILL
STOP
2
3
Press OPERATE.
TAPE
SPEED
DPSS
SKIP
SLOW
Move VCR/DVD CHANGE Switch on the Remote to DVD.
AUDIO
OUTPUT
CH
VCR
DVD
VCR
DVD
4
Press VCR/DVD SELECTOR to enter the DVD mode.
• The VCR/DVD SELECTOR on the product lights up in green.
VCR/DVD COMBINATION
VCR/DVD
SELECTOR
Light up in green
• Each time VCR/DVD SELECTOR is pressed, the mode
changes between “VCR” mode and “DVD” mode.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
78
Playback
Preparation
• See Preparing to Use DVD on page 78.
OPEN/CLOSE
OPERATE
VIDEO
C D
CD-R/RW
DVD
C D
OPERATE EJECT/STOP
REW PLAY/×
2
PLAY
STOP
OPEN/CLOSE
REC
/
TIMER
VCR/DVD
SELECTOR
CH
VCR DVD
(
L
)
-
AV
2
IN VIDEO
MONO AUDIO R
-
• The icons below are used in this Operation Manual:
DVD
................... Indicates the functions that can be performed
for DVDs.
STOP
C D
................... Indicates the functions that can be performed
Disc
for AUDIO CDs.
............... Indicates the functions that can be performed
PLAY
CD-R/RW
/CLOSE
for CD-R/RW.
VCR
VIDEO
C D
VD
R/D
VC
SEL
OR
ECT
.................... Indicates the functions that can be performed
for VIDEO CD.
1
2
Basic Play
G-CODE
PROG
DV- NC70W
1
2
3
Press OPERATE.
DV- NC70
DV- NC70X
Press îOPEN/CLOSE to open the disc tray.
Place a disc onto the tray.
• Hold the disc without touching either of its surfaces, position it
with the printed title side facing up, align it with the guides,
and place it in its proper position.
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
1 8 cm (3") disc
2 12 cm (5") disc
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
• Do not stack discs in the tray. This can damage the player
and the discs.
TITLE
DVD MENU
4
5
Press î OPEN/CLOSE to close the disc tray.
CLEAR
RETURN
SET
ENTER
Press ûPLAY.
ZERO BACK
• Playback image appears on the screen. (No image is shown
for audio CDs.)
SKIP SEARCH
6
Press ËSTOP to stop playback.
Playing VIDEO CDs with Playback Control (PBC)
• Pressing ûPLAY begins PBC playback. Time display is not
shown for some discs.
AM/PM
INPUT SELECT VCR DVD
/
REV
FWD
• If you specify the track number to be played (with playback
stopped) and press ûPLAY, normal playback (not PBC
playback) begins.
PLAY
REC
PAUSE/STILL
STOP
TAPE
SPEED
DPSS
SKIP
SLOW
• If the disc is loaded upside down or is damaged, “– – – – –” appears
on the DVD Front Panel display and the disc tray slides out.
• If you attempt to play a DVD disc with the wrong region code, “
REGION CODE ERROR” appears on the TV screen and the disc tray
slides out.
AUDIO
OUTPUT
CH
VCR
DVD
VIDEO
C D
CD-R/RW
C D
VCR/DVD COMBINATION
Track Direct Playback
1
To display the title number you want to watch, press the number
buttons (0 to 9) on the Remote while playing or stopping an image.
2
Press ûPlay.
• The track number you entered in step 1 is played.
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
79
Playback
VIDEO
C D
CD-R/RW
DVD
C D
Fast Forward/Fast Reverse
OPERATE EJECT/STOP
REW PLAY/×2
PLAY
STOP
OPEN/CLOSE
è
È
REC
/
1
Press FWD
or
REV during playback.
TIMER
VCR/DVD
SELECTOR
CH
VCR DVD
(
L
)
-
AV
2
IN VIDEO
MONO AUDIO R
-
• The disc begins fast scan at ×2 speed (1).
Scanning speed selection
1
PLAY
DVD
Fast scan image appears here.
(No image is shown for Audio CDs.)
G-CODE
PROG
DV- NC70W
• Three speeds are available for DVD, VIDEO CDs and Audio
CDs. Each time FWDè or ÈREV is pressed, the speed of
fast scan changes in the following sequence:
DV- NC70
DV- NC70X
1 (about ×2)
2 (about ×8)
3 (about ×32)
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
2
Press ûPLAY when you reach the desired point.
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
TITLE
DVD MENU
• On some discs, the fast scan function is disabled.
• On DVD discs, audio and subtitles are not played back during the fast
scan playback. Audio is played back only when the search speed of
the fast forward is 1 (about ×2).
CLEAR
RETURN
SET
ENTER
ZERO BACK
• With a DVD disc, you cannot search past a title. Playback starts from
the beginning of the title.
SKIP SEARCH
• Depending on the audio equipment, the sound may not come out
when the fast forward is 1 (about ×2).
AM/PM
INPUT SELECT VCR DVD
/
VIDEO
C D
REV
FWD
DVD
PLAY
Slow-Motion Play
REC
PAUSE/STILL
STOP
1
Press SLOW in the play mode or still mode.
TAPE
SPEED
DPSS
SKIP
SLOW
• Three speeds are available. Each time SLOW is pressed,
the speed of slow-motion playback changes in the following
AUDIO
OUTPUT
CH
sequence:
(DVD)
VCR
DVD
1 (about ×1/2)
2 (about ×1/8)
3 (about ×1/16)
VCR/DVD COMBINATION
2
Press ûPLAY to return to the normal playback or press
â
PAUSE/STILL to return to the still picture mode.
• On some discs, the slow-motion playback functions are disabled.
• Slow-motion playback is disabled on Audio CDs and MP3 discs.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
80
Playback
VIDEO
C D
CD-R/RW
DVD
C D
Still/Pause
OPERATE EJECT/STOP
REW PLAY/×2
PLAY
STOP
OPEN/CLOSE
REC
/
TIMER
â
VCR/DVD
SELECTOR
CH
1
2
Press PAUSE/STILL during playback.
VCR DVD
(
L
)
-
AV
2
IN VIDEO
MONO AUDIO R
-
If you press ûPLAY while paused (STILL/PAUSE), normal
playback resumes.
PLAY
VIDEO
C D
DVD
G-CODE
PROG
DV- NC70W
Frame Advance
DV- NC70
DV- NC70X
â
1
Press PAUSE/STILL during playback.
• The playback is paused (STILL/PAUSE).
• The disc goes forward by one frame each time
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
â
PAUSE/STILL is pressed.
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
2
Press ûPLAY to return to the normal playback.
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
TITLE
DVD MENU
VIDEO
C D
CD-R/RW
DVD
C D
CLEAR
RETURN
SET
ENTER
Skip (Forward/Reverse)
ZERO BACK
While you are playing a disc, this function jumps to the beginning of
the next chapter/track (Forward) or the current chapter/track (Reverse)
and automatically starts playing that chapter/track.
SKIP SEARCH
AM/PM
INPUT SELECT VCR DVD
À
SKIP.
1
While a disc is playing, press SKIPà or
/
• Playback skips forwards one chapter/track for each time
REV
FWD
SKIPà is pressed.
PLAY
À
• If you press
SKIP and playback begins, and you then
À
press
SKIP again within 3 seconds, playback returns to
REC
PAUSE/STILL
the beginning of the previous chapter/track.
STOP
TAPE
SPEED
DPSS
SKIP
SLOW
AUDIO
OUTPUT
CH
• The frame advance playback functions are disabled for audio CDs and
MP3 discs.
VCR
DVD
• On discs or titles that do not have chapter settings, playback skips
forward to the next title or back to the beginning of the current title or
disc.
• On some discs, the skip functions are disabled.
• The playback image is not displayed during the skip. It resumes
during playback following the skip.
VCR/DVD COMBINATION
When VIDEO CDs are played in PBC mode:
• Pressing SKIPà causes the disc to move to the NEXT position.
À
• Pressing
SKIP causes the disc to move to the PREVIOUS position.
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
81
DVD
Angle Selection
Some DVD discs contain scenes which have been shot simulta-
neously from a number of different angles. For these discs, the same
scene can be viewed from each of these different angles. (The
recorded angles differ depending on the disc used.)
G-CODE
PROG
1
While you are playing a DVD disc with different angles recorded,
press ANGLE to view the number of the current angle.
DV- NC70W
DV- NC70
DV- NC70X
1
Number changes to show the number of
the current angle. (The maximum number
stipulated by the manufacturers is 9.)
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
TITLE
DVD MENU
CLEAR
RETURN
SET
ENTER
Lights when different angles are recorded for the
title currently playing.
ZERO BACK
2
Use ' or " (or ANGLE) to change the scene to the next angle
in those recorded.
SKIP SEARCH
• About two seconds later, playback continues from the new
angle you selected.
AM/PM
INPUT SELECT VCR DVD
• If no button is pressed within 10 seconds, playback contin-
ues without changing the current angle.
/
REV
FWD
PLAY
Sequence of angle shots
(Example)
REC
PAUSE/STILL
STOP
2
3
1
TAPE
SPEED
DPSS
SKIP
SLOW
98
98
98
AUDIO
OUTPUT
CH
98
VCR
DVD
VCR/DVD COMBINATION
• This function can only be used for discs on which scenes shot from
multiple angles have been recorded.
• If no angles are recorded on the disc,
xx is displayed.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
82
Playing MP3 Discs
This product is able to play CD-R or CD-RW discs recorded in MP3 format.
Regarding MP3 discs
•
MP3 files are audio data compressed in MPEG1 Audio layer 3 file format. “MP3 files” have “.mp3” as extensions.
(Some files that have “.mp3” extensions or files that have not been recorded in MP3 format will produce noise or
cannot be played.)
• Some discs cannot be played depending on the actual CD-R/CD-RW disc condition, the recording equip-
ment and the disc’s recording.
• Data on the CD-R or CD-RW disc, which has not been recorded in MP3 format, audio tracks or has been
recorded in other file formats except MP3, cannot be played.
Playing MP3 discs
• Discs that have more than 255 folders and files in total cannot be played.
• Some MP3 files are not played in the order they were recorded.
• The number of layers, which can be recognized, including files and folders, is maximum 8.
• Only the first session of a multi-session disc can be played.
• When both audio tracks and MP3 files are recorded on a disc, audio tracks will be played.
• Depending on the folder tree, reading MP3 files can take time.
• The more files there are, the longer the reading time. Therefore it is recommended to lower the number of
folders before recording.
• Folder or track (file) names are limited to 8 characters. The folder / file names are displayed in half-size,
capital letters or half-size numbers. Folder or track (file) names that go over 8 characters will be abbreviated.
• Certain letters or symbols in folder names or file names may not be displayed. In this case, “?” will be
displayed.
• The playing time may not be correctly displayed during MP3 file playback.
• It is recommended to record data at a lower speed as data recorded at fast speed can produce noise and
may not be able to be played.
CAUTION
• It is impossible to make a digital copy by using a digital audio recording device which outputs sound from discs in MP3
format through the coaxial digital output jack of this product.
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
83
Playing MP3 Discs
To play MP3 discs
1
Load the MP3 recorded CD-R or the CD-RW.
• The folder selection screen will be displayed after the data is
read.
G-CODE
PROG
DV- NC70W
1/
4
MP3
DV- NC70
DV- NC70X
FOLDER1
FOLDER3
FOLDER2
FOLDER4
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
2
Select the folder you want to play by using ', ", \ or | and
then press ENTER.
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
• The file (music title) in the folder is displayed on the file
selection screen.
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
TITLE
DVD MENU
FOLDER1
MP3
CLEAR
RETURN
SET
ENTER
1 TITLE01
3 TITLE03
2 TITLE02
4 TITLE04
ZERO BACK
• Press RETURN to return to the folder selection screen.
• When pressing |PLAY after selecting the folder, the
playback screen is displayed, and the files in that folder can
be played from the beginning.
SKIP SEARCH
AM/PM
INPUT SELECT VCR DVD
3
4
Select the file (music title) you want to play by using ', ", \ or
| and then press ENTER.
• The chosen file (music title) will be played in sequence.
/
REV
FWD
PLAY
FOLDER1
MP3
REC
PAUSE/STILL
STOP
1 TITLE01
3 TITLE03
5 TITLE05
7 TITLE07
2 TITLE02
4 TITLE04
6 TITLE06
8 TITLE08
TAPE
SPEED
DPSS
SKIP
SLOW
AUDIO
OUTPUT
CH
FOLDER1
7 TITLE07
VCR
DVD
Press ËSTOP to stop play.
To play another file (music title) while playing
1
Press ', ", \ , | to select the file (music title) you want to play
and then press ENTER.
VCR/DVD COMBINATION
• The chosen file (music title) will be played.
• The file where the cursor is on, will be played when the cursor is
moved to a different from the file being played and no operation is
taken within 10 seconds.
• Press RETURN to return to the folder selection screen.
To skip the file while playing
À
1
Press SKIPà or
SKIP during playback.
À
• SKIPà will skip forward, and
SKIP will rewind.
• When playing files (tracks) from other folders, press RETURN
and then select the files from the folder selection screen.
While the MP3 disc is playing
• Time Search is disabled.
• Programmed playback is disabled.
• It is possible to repeat one track or the entire folder.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
84
About the Function Control Screen
Using Function control, you can check at a glance and change the current settings of the following items:
SUBTITLE, ANGLE, AUDIO, 3D VIRTUAL SURROUND and, DIGITAL GAMMA.
Function control also allows you three ways of direct skips (title [track], chapter and time).
• While the disc is playing, press FUNCTION CONTROL to display the screen shown below.
• Pressing ' or " changes the currently selected item.
• Numbers in
refer to the pages where the setting procedures are described.
1
2
3
4
5
6
7
Direct title skip
Direct chapter skip
Currently selected item
2/5
8/3‰
‰1:3‰:‰8
T
C
DVD
Direct time skip
Subtitle
BIT RATE indicates the
amount of data that is
being transferred to the
product per second.
However, note that
picture quality is not
always in proportion to
the bit rate.
2
ENGLISH
1
Angle
0
5
10
D
1
5
.
1ch
BIT RATE
Mbps
Audio
ON
ON
SELECT
ENTER
ENTER
G
RETURN
3D VIRTUAL
SURROUND
8
DIGITAL GAMMA
1
Direct title skip
6
Audio setting
86
89
The type of audio currently selected is displayed.
• You can select the desired type of audio.
• The number of the title currently played back is
displayed.
•
• You can skip directly to the desired title.
7
3D VIRTUAL SURROUND setting
90
2
Direct chapter skip
86
• This function provides rich surround sound by
downmixing Dolby Digital 5.1 channel and Dolby
Surround (Pro Logic) to 2-channel audio or TV.
• You can toggle the setting between “ON” and “OFF”,
and change the level.
• When “COMPRESSION” is “ON”, this function is
disabled, which is indicated by xx. To use the 3D
VIRTUAL SURROUND function, set the
• The number of the chapter currently played back is
displayed.
• You can skip directly to the desired chapter.
86
Direct time skip
Elapsed time from the beginning of the disc is displayed.
3
•
• You can skip directly to the point from which you want
to start playback.
“COMPRESSION” to “OFF” (see page 44).
4
Subtitle setting 87
8
DIGITAL GAMMA setting 91
• The subtitle number and language currently selected
are displayed. (When a disc with only one subtitle is
played back, xx is displayed.)
• You can make the entire image easier to see by
brightening the darker and obscure portions.
• You can toggle the setting between “ON” and “OFF”,
and change the level.
• You can select the desired subtitle language.
5
Angle setting
88
• The current angle is displayed. (When a disc with
only one angle is played back, xx is displayed.)
• You can select the desired angle.
• In Function control mode, you can return to the previous setting screen by pressing RETURN or
FUNCTION CONTROL.
• You can cancel the Function control mode by pressing ËSTOP, DVD MENU or TITLE.
• The setting screen is cleared automatically whenever you display a DVD screen that prompts you to change the
scene by pressing ', ", \, or |.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
85
About the Function Control Screen
VIDEO
DVD
C D
C D
Direct skip (title [track]/chapter/time)
Use the following procedure to perform the Direct title [track] skip,
Direct chapter skip, or Direct time skip.
G-CODE
PROG
DV- NC70W
DV- NC70
DV- NC70X
1
Press FUNCTION CONTROL during playback.
• The Function control screen appears.
2/5
8/3‰
‰1:3‰:‰8
T
TIMER
OPERATE
DISPLAY
DVD
ON/OFF
EJECT
C
ON
VCR/DVD VCR MENU
2
ENGLISH
SCREEN SELECTOR DVD SETUP
1
1
0
5
10
Mbps
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
D
5
.
1ch
BIT RATE
ANGLE
ON
ON
SELECT
ENTER
ENTER
TITLE
DVD MENU
G
RETURN
CLEAR
RETURN
SET
ENTER
2
Use ' or " to select
and then press ENTER.
ZERO BACK
(Example) Direct title skip
SKIP SEARCH
--/5
8/3‰
‰1:3‰:‰8
T
DVD
C
2
1
1
ENGLISH
AM/PM
INPUT SELECT VCR DVD
0
5
10
Mbps
/
5
.1ch
BIT RATE
ON
ON
SELECT
ENTER
REV
FWD
ENTER
G
RETURN
PLAY
REC
PAUSE/STILL
3
4
Use number buttons (0 to 9) to input the title number to which
you want to skip.
• You can also use ' or " to input the title number.
STOP
TAPE
SPEED
DPSS
SKIP
SLOW
(Example) Entering title 5
AUDIO
OUTPUT
CH
5/5
8/3‰
‰1:3‰:‰8
T
VCR
DVD
DVD
C
2
ENGLISH
1
1
0
5
10
Mbps
5
.
1ch
BIT RATE
ON
ON
SELECT
ENTER
ENTER
G
RETURN
VCR/DVD COMBINATION
Press ENTER.
• The played back image changes to the beginning of the
specified title.
• You can exit the Function control screen by pressing
RETURN or FUNCTION CONTROL.
• The number of titles, chapters or times you can input depends on that
of the titles, chapters or times recorded on a disc you play.
• Direct chapter skip can only be used for DVD discs.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
86
About the Function Control Screen
DVD
Subtitle language setting
Use the following procedure to perform the Subtitle language setting.
G-CODE
DV- NC70W
1
Press FUNCTION CONTROL during playback.
• The Function control screen appears.
PROG
DV- NC70
DV- NC70X
2/5
8/3‰
‰1:3‰:‰8
T
DVD
C
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
2
ENGLISH
ON
VCR/DVD VCR MENU
1
1
SCREEN SELECTOR DVD SETUP
0
5
10
Mbps
D
5
.
1ch
BIT RATE
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ON
ON
SELECT
ENTER
ANGLE
ENTER
G
RETURN
TITLE
DVD MENU
2
3
Use ' or " to select
and then press ENTER.
CLEAR
SET
RETURN
ENTER
ZERO BACK
2/5
8/3‰
‰1:3‰:‰8
T
C
DVD
SKIP SEARCH
2
ENGLISH
1
1
0
5
10
Mbps
5
.
1ch
BIT RATE
ENTER
AM/PM
INPUT SELECT VCR DVD
ON
ON
SELECT
/
G
ENTER
RETURN
REV
FWD
Press ' or " to select the subtitle language you want to use.
• You can set the subtitle setting to “OFF”.
• You can also toggle the setting between “ON” and “OFF” by
pressing \ or |.
PLAY
REC
PAUSE/STILL
STOP
TAPE
SPEED
DPSS
SKIP
(Example) Selecting “3 SPANISH”
SLOW
AUDIO
OUTPUT
CH
2/5
8/3‰
‰1:3‰:‰8
T
DVD
C
VCR
DVD
3
SPANISH
1
1
ON
ON
0
5
10
Mbps
5
.1ch
BIT RATE
ENTER
SELECT
G
ENTER
RETURN
VCR/DVD COMBINATION
4
Press ENTER to confirm the setting.
• You can exit the Function control screen by pressing
RETURN or FUNCTION CONTROL.
• This function can only be used for discs on which subtitles have been
recorded in multiple languages.
• Some DVD discs are marked “Forced Display”, indicating that the
subtitling cannot be suppressed. With such discs, the subtitles will be
displayed even when you select “
OFF” display. This does not
indicate a fault with this product.
• If no subtitles are recorded on the disc,
xx is displayed.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
87
About the Function Control Screen
DVD
Angle setting
You can change the angle of view when playing a DVD disc that
contains scenes recorded from multiple angles.
Use the following procedure to perform the Angle setting.
G-CODE
PROG
DV- NC70W
DV- NC70
DV- NC70X
1
Press FUNCTION CONTROL during playback.
• The Function control screen appears.
2/5
8/3‰
‰1:3‰:‰8
T
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
DVD
C
ON
VCR/DVD VCR MENU
2
ENGLISH
SCREEN SELECTOR DVD SETUP
1
1
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
0
5
10
Mbps
D
ANGLE
5
.
1ch
BIT RATE
ON
ON
SELECT
ENTER
TITLE
DVD MENU
ENTER
G
RETURN
CLEAR
SET
2
3
Use ' or " to select
and then press ENTER.
RETURN
ENTER
ZERO BACK
2/5
8/3‰
‰1:3‰:‰8
T
DVD
C
SKIP SEARCH
2
ENGLISH
1
1
0
5
10
Mbps
5.
1ch
BIT RATE
ON
ON
SELECT
ENTER
AM/PM
INPUT SELECT VCR DVD
ENTER
G
RETURN
/
REV
FWD
Press ' or " to select the angle number you want.
• The number of recorded angles differs depending on the disc used.
PLAY
REC
PAUSE/STILL
2/5
8/3‰
‰1:3‰:‰8
T
STOP
DVD
C
TAPE
SPEED
DPSS
SKIP
2
ENGLISH
SLOW
2
1
AUDIO
OUTPUT
0
5
10
Mbps
5.1ch
CH
BIT RATE
ON
ON
SELECT
ENTER
ENTER
VCR
DVD
G
RETURN
4
Press ENTER to confirm the setting.
• You can exit the Function control screen by pressing RETURN or
FUNCTION CONTROL.
VCR/DVD COMBINATION
• This function can only be used for discs on which scenes shot from
multiple angles have been recorded.
• If no angles are recorded on the disc,
xx is displayed.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
88
About the Function Control Screen
VIDEO
C D
DVD
Audio setting
A number of different methods are used to record audio onto a DVD
disc, including multi-channels (used for voiceovers in other languages),
Dolby Digital (5.1ch), DTS, and Linear PCM. This product provides a
number of different audio modes from which you can choose to suit
the type of disc you are playing.
G-CODE
DV- NC70W
PROG
DV- NC70
DV- NC70X
Use the following procedure to perform the Audio setting.
TIMER
1
Press FUNCTION CONTROL during playback.
• The Function control screen appears.
OPERATE
DISPLAY
ON/OFF
EJECT
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
2/5
8/3‰
‰1:3‰:‰8
T
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
DVD
ANGLE
C
TITLE
DVD MENU
2
ENGLISH
1
0
5
10
D
1
ON
ON
5
.
1ch
CLEAR
RETURN
SET
BIT RATE
Mbps
ENTER
SELECT
ENTER
ENTER
G
RETURN
ZERO BACK
SKIP SEARCH
2
3
Use ' or " to select
and then press ENTER.
2/5
8/3‰
‰1:3‰:‰8
T
DVD
C
AM/PM
INPUT SELECT VCR DVD
/
2
ENGLISH
REV
FWD
1
0
5
10
Mbps
D
1
5
.
.
1ch
BIT RATE
PLAY
ON
ON
SELECT
ENTER
ENTER
G
RETURN
REC
PAUSE/STILL
STOP
Press ' or " to select the audio format you want to use.
• See page 44 for details about the types of audio format.
TAPE
SPEED
DPSS
SKIP
SLOW
AUDIO
OUTPUT
CH
2/5
8/3‰
‰1:3‰:‰8
T
DVD
C
VCR
DVD
2
1
ENGLISH
0
5
10
Mbps
2LPCM
ON
ON
5
.
1ch
BIT RATE
SELECT
ENTER
ENTER
G
RETURN
VCR/DVD COMBINATION
• When watching the video CD, the audio channels changes as the
following sequence:
L+R
L
R
4
Press ENTER to confirm the setting.
• You can exit the Function control screen by pressing RETURN or
FUNCTION CONTROL.
• This function can only be used for discs on which the sound has been
recorded in multiple formats.
• With certain types of discs, you can change the audio using the disc
menu. (See page 44.)
• A DTS digital surround decoder is required to listen to DTS audio.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
89
About the Function Control Screen
DVD
G-CODE
PROG
DV- NC70W
3D VIRTUAL SURROUND setting
DV- NC70
DV- NC70X
This function allows you to enjoy a “surround sound” effect when you
are using an analog connection (using AV 1 OUT on this product) to
2-channel audio equipment (TV, etc.).
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
Preparation
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
To use the 3D VIRTUAL SURROUND function
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
•
Set the “COMPRESSION” setting in “AUDIO” to “OFF” (see page 44).
ANGLE
Refer to the table below about the types of audio format with which
3D VIRTUAL SURROUND works.
TITLE
DVD MENU
CLEAR
RETURN
SET
ENTER
Types of audio recorded on the disc
ZERO BACK
Dolby Digital
Dolby
Digital
Dolby
Pro Logic
2ch/Linear
PCM
DTS
SKIP SEARCH
✕
AM/PM
INPUT SELECT VCR DVD
/
REV
FWD
1
2
Press FUNCTION CONTROL during playback.
• The Function control screen appears.
PLAY
REC
PAUSE/STILL
2/5
8/3‰
‰1:3‰:‰8
T
DVD
STOP
C
TAPE
SPEED
DPSS
SKIP
2
ENGLISH
SLOW
1
1
0
5
10
Mbps
AUDIO
OUTPUT
D
5
.
1ch
BIT RATE
CH
ON
ON
SELECT
ENTER
ENTER
G
RETURN
VCR
DVD
Use ' or " to select
and then press ENTER.
2/5
8/3‰
‰1:3‰:‰8
T
VCR/DVD COMBINATION
DVD
C
2
ENGLISH
1
1
ON
ON
0
5
10
Mbps
5.1ch
BIT RATE
ENTER
SELECT
G
ENTER
RETURN
• 3D VIRTUAL SURROUND does not
operate on Audio CDs.
• 3D VIRTUAL SURROUND does not
operate when you set the
“COMPRESSION” setting in “AUDIO
SETUP” to “ON”.
3
4
Press ' or " to toggle 3D VIRTUAL SURROUND between
“ON” and “OFF”.
While “ON” is selected, use \ or | to change the level setting.
• 3D VIRTUAL SURROUND does not
operate when you are using a Digital
connection.
• 3D VIRTUAL SURROUND does not
operate when you playback a disc
recorded using DTS format.
2/5
8/3‰
‰1:3‰:‰8
T
DVD
C
2
ENGLISH
1
1
ON
ON
0
5
10
Mbps
5.1ch
BIT RATE
ENTER
SELECT
G
ENTER
RETURN
5
Press ENTER to confirm the setting.
• You can exit the Function control screen by pressing
RETURN or FUNCTION CONTROL.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
90
About the Function Control Screen
VIDEO
C D
DVD
DIGITAL GAMMA setting
DIGITAL GAMMA is a digital image quality enhancement function
that gives a richer image by brightening the darker and more
obscure portions of the image without altering the brightness of the
brighter portions, thereby making the entire image easier to see.
Three digital gamma settings are available to allow for differences in
the images played and in brightness of the room.
G-CODE
DV- NC70W
PROG
DV- NC70
DV- NC70X
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
1
Press FUNCTION CONTROL during playback.
• The Function control screen appears.
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
2/5
8/3‰
‰1:3‰:‰8
T
DVD
C
TITLE
DVD MENU
2
ENGLISH
1
1
CLEAR
RETURN
SET
ENTER
0
5
10
Mbps
D
5
.
1ch
BIT RATE
ON
ON
SELECT
ENTER
ZERO BACK
ENTER
G
RETURN
SKIP SEARCH
2
Use ' or " to select
and then press ENTER.
2/5
8/3‰
‰1:3‰:‰8
T
AM/PM
INPUT SELECT VCR DVD
DVD
C
/
REV
FWD
2
ENGLISH
1
1
ON
ON
0
5
10
Mbps
PLAY
5.1ch
BIT RATE
ENTER
SELECT
REC
PAUSE/STILL
G
ENTER
RETURN
STOP
TAPE
SPEED
DPSS
SKIP
3
4
Press ' or " to toggle DIGITAL GAMMA between “ON” and
“OFF”.
SLOW
AUDIO
OUTPUT
CH
VCR
DVD
While the “
ON” is displayed, press \ or |.
• The level selection indicator that shows the current level
appears.
5
Use \ or | to change the level.
VCR/DVD COMBINATION
2/5
8/3‰
‰1:3‰:‰8
T
DVD
C
2
ENGLISH
1
1
ON
ON
0
5
10
Mbps
5.1ch
BIT RATE
ENTER
SELECT
G
ENTER
RETURN
6
Press ENTER to confirm the setting.
You can exit the Function control screen by pressing RETURN
or FUNCTION CONTROL
•
.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
91
Direct Selection of Scenes
DVD
Selecting Scenes by Title Number
G-CODE
PROG
DV- NC70W
1
Press TITLE to show the title screen.
DV- NC70
DV- NC70X
(Example)
DISCOVERY EUROPE
DISCOVERY AFRICA
1
2
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
2
3
Use ', ", | or \ to highlight the desired title.
TITLE
DVD MENU
CLEAR
RETURN
SET
ENTER
When you press ENTER or û PLAY, the title specified in step 2
starts playing.
ZERO BACK
SKIP SEARCH
Selecting Scenes from the Menu Screen
1
Press DVD MENU to show the menu screen.
AM/PM
INPUT SELECT VCR DVD
(Example)
/
T I T L E M E N U
REV
FWD
1
3
2
4
C
D
a
ts
F i
s
r
hes
PLAY
REC
PAUSE/STILL
og
s
B
i
ds
STOP
TAPE
SPEED
DPSS
SKIP
SLOW
2
3
Use ', ", | or \ to highlight the desired title.
AUDIO
OUTPUT
CH
(Example) Title 2 selected.
VCR
DVD
T I T L E M E N U
1
3
2
4
C
D
a
ts
F i
s
r
hes
VCR/DVD COMBINATION
og
s
B
i
ds
When you press ENTER or û PLAY, title 2 starts playing.
• These functions only operate on DVD discs that have a title or menu
screen.
• Languages not provided on the disc are not displayed.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
92
Programmed Playback
The two types of programmed playback provided by this product are
chapter programmed playback (DVD discs) and track programmed
playback (Audio CD discs).
DVD
G-CODE
PROG
DV- NC70W
DV- NC70
DV- NC70X
Chapter Programmed Playback
1
Press PROG while the disc is stopped.
• The “DVD-VIDEO PROGRAM” screen appears.
• Press PROG to return to the normal screen.
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
ON
VCR/DVD VCR MENU
DVD-VIDEO PROGRAM
TITLE
SCREEN SELECTOR DVD SETUP
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
1
2
3
TITLE
DVD MENU
CLEAR
RETURN
SET
ENTER
ENTER
SELECT
SET
ZERO BACK
2
3
Press ' or " to select the desired title and then press ENTER.
• The chapter selection screen appears.
DVD-VIDEO PROGRAM
SKIP SEARCH
:
2
:
2
1
2
3
1:
2:
3:
4:
5:
6:
AM/PM
INPUT SELECT VCR DVD
/
REV
FWD
PLAY
SELECT
S TA R T
RETURN
REC
PAUSE/STILL
Press ' or " to select the desired chapter and press ENTER.
• The chapter is programed in the playlist.
STOP
TAPE
SPEED
DPSS
SKIP
SLOW
DVD-VIDEO PROGRAM
:
2
:
2
AUDIO
OUTPUT
CH
1
2
3
1:
2:
3:
4:
5:
6:
3
1
VCR
DVD
SELECT
S TA R T
RETURN
• Repeat the above step for each of the chapters that you want
to play as part of the program.
VCR/DVD COMBINATION
• To delete the chapter programmed in the playlist, follow the
steps below.
1 Press | to move the cursor to the playlist.
2 Press ' or " to select the program (chapter) you want to
delete and then press RETURN.
• To delete all programmed chapters, move the cursor to the
playlist and then press RETURN for more than two seconds.
•
Up to 24 chapters can be programmed.
• Press RETURN to return to the
previous screen.
• The program cannot be set during the
normal playback.
• This function can only be used for
DVD discs on which the chapter has
been recorded.
• On some discs in which programmed
playback is prohibited, this function is
disabled.
4
5
Press ûPLAY to begin playing the programmed chapters.
• The chapters will be played in the order they were entered.
• The PROGRAM indicator lights up on the DVD Front Panel
display.
Press ËSTOP to stop programmed playback.
• To start programmed playback again, follow the steps below.
1 Press ËSTOP to stop programmed playback.
2 Press PROG.
3 Select the title you programmed and press ENTER. (If
other titles are selected, the previously entered program
will be cleared.)
4 Press ûPLAY.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
93
Programmed Playback
VIDEO
C D
C D
Track Programmed Playback
G-CODE
PROG
DV- NC70W
1
Press PROG while the disc is stopped.
• The “PROGRAM” screen appears.
• Press PROG to return to the normal screen.
DV- NC70
DV- NC70X
Example : CD PROGRAM screen
CDPROGRAM
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
:
:
:
:
:
:
1
2
3
4
5
6
1
2
3
4
5
6
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
TITLE
DVD MENU
SELECT
S TA R T
CLEAR
RETURN
SET
ENTER
2
Press ' or " to select the desired track and then press ENTER.
• The track is programmed in the playlist.
ZERO BACK
CDPROGRAM
SKIP SEARCH
:
:
:
:
:
:
1
2
3
4
5
6
1
2
3
4
5
6
3
2
AM/PM
INPUT SELECT VCR DVD
/
REV
FWD
SELECT
S TA R T
PLAY
3
4
5
Repeat step 2 for each of the tracks that you want to play as part
of the program.
REC
PAUSE/STILL
STOP
Press ûPLAY to begin playing the programmed tracks.
• The tracks will be played in the order they were entered.
TAPE
SPEED
DPSS
SKIP
SLOW
AUDIO
OUTPUT
CH
Press ËSTOP to stop programmed playback.
VCR
DVD
• Up to 24 tracks can be programmed.
• Press RETURN to return to the previous screen.
• The program cannot be set during the normal playback.
• On some discs in which programmed playback is prohibited, this
function is disabled.
VCR/DVD COMBINATION
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
94
Programmed Playback
CD-R/RW
MP3 Files Programmed Playback
G-CODE
DV- NC70W
1
Press PROG while the disc is stopped.
• The “MP3 PROGRAM” screen appears.
• Press PROG to return to the normal screen.
PROG
DV- NC70
DV- NC70X
MP3 PROGRAM
:
1/
4
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
:
:
:
:
:
:
FOLDER1
FOLDER2
FOLDER3
FOLDER4
FOLDER4
FOLDER4
1
2
3
4
5
6
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
ENTER
SELECT
SET
TITLE
DVD MENU
2
3
Press ' or " to select the desired folder and then press
ENTER.
CLEAR
SET
RETURN
ENTER
MP3 PROGRAM
FOLDER1
ZERO BACK
SKIP SEARCH
:
1
:
2
:
3
:
4
:
5
:
6
TITLE01
TITLE02
TITLE03
TITLE04
TITLE05
TITLE06
AM/PM
INPUT SELECT VCR DVD
/
SELECT
S TA R T
RETURN
REV
FWD
Press ' or " to select the desired file and press ENTER.
• The file is programed in the playlist.
• Press RETURN to return to step 2 and then select the files of
other folder.
PLAY
REC
PAUSE/STILL
STOP
MP3 PROGRAM
FOLDER1
TAPE
SPEED
DPSS
SKIP
SLOW
:
TITLE01
TITLE02
TITLE03
TITLE04
TITLE05
TITLE06
1 TITLE03
AUDIO
OUTPUT
CH
:
2 TITLE04
:
3 TITLE01
VCR
DVD
:
4
:
5
:
6
SELECT
S TA R T
RETURN
• Repeat the above step for each of the files that you want to
play as part of the program.
VCR/DVD COMBINATION
• To delete the files programmed in the playlist, follow the steps
below.
1 Press | to move the cursor to the playlist.
2 Press ' or " to select the program (track/file) you want to
delete and then press RETURN.
To delete all programmed chapter number, move the cursor to
the playlist and then press RETURN for more than two seconds.
•
4
5
Press ûPLAY to begin playing the MP3 files.
• The files will be played in the order they were entered.
Press ËSTOP to stop programmed playback.
• To start programmed playback again, follow the steps below.
1 Press ËSTOP to stop programmed playback.
2 Press PROG.
3 Select the file you programmed and press ENTER.
4 Press ûPLAY.
• Up to 24 chapters can be programmed.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
95
C D
DVD
VIDEO
C D
CD-R/RW
Repeat Playback
Repeat playback
1
Press (REPEAT) while a disc is playing.
• The “ ” indicator appears on the DVD Front Panel.
G-CODE
PROG
• Each time (REPEAT) is pressed, the repeat function
changes as follows.
DV- NC70W
DV- NC70
• Depending on the disc type, the repeat function will vary.
DV- NC70X
DVD
TIMER
ON/OFF
OPERATE
EJECT
Chapter Repeat
ON
VCR/DVD VCR MENU
DISPLAY
SCREEN SELECTOR DVD SETUP
C
DVD
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
TITLE
DVD MENU
"
Title Repeat
CLEAR
RETURN
SET
ENTER
T
DVD
"
ZERO BACK
A-B Repeat
(See the next page for details.)
SKIP SEARCH
"
OFF
AM/PM
INPUT SELECT VCR DVD
/
VIDEO
C D
C D
REV
FWD
PLAY
Track Repeat
T
DVD
REC
PAUSE/STILL
STOP
TAPE
SPEED
DPSS
SKIP
"
SLOW
Repeat all files in the disc
AUDIO
OUTPUT
CH
DVD
VCR
DVD
"
A-B Repeat
(See the next page for details.)
"
OFF
VCR/DVD COMBINATION
CD-R/RW
(Only MP3 File Format)
Repeat one file
T
DVD
R"epeat all files in the folder
"
OFF
2
Press ENTER to start repeat playback.
• Press (REPEAT) and select OFF when returning to regular
playback.
• Repeat playback is disabled on some discs.
• Repeat playback cannot be used during programmed playback.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
96
Repeat Playback
VIDEO
C D
C D
A-B Repeat
DVD
A-B repeat allows you to repeat specified section on the disc.
G-CODE
DV- NC70W
1
2
Press (REPEAT) three times while a disc is playing.
PROG
DV- NC70
DV- NC70X
While you are playing a disc, press ENTER when you reach the
start of the section to be repeated.
TIMER
OPERATE
DISPLAY
3
While the disc is playing the same chapter/track, press ENTER
again when you reach the end of the section to be repeated.
ON/OFF
EJECT
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
A B
DVD
ANGLE
TITLE
DVD MENU
CLEAR
RETURN
SET
ENTER
ZERO BACK
• The A-B repeat begins from the point where you specified in
step 2.
SKIP SEARCH
• Press (REPEAT) to turn off the “ ” indicator when returning
to regular playback.
AM/PM
INPUT SELECT VCR DVD
/
REV
FWD
• To cancel A-B repeat, press Ë STOP, TITLE or DVD MENU.
• A-B repeat can only be used within the same title/track.
(On some DVD discs, A-B repeat is restricted to the same chapter.)
If the title/track finishes before specifying the ending location (B), the
location where the title/track finishes will be set as the ending location (B).
• The A-B repeat function cannot be used during programmed playback.
• If the DVD Front Panel display does not show the elapsed playback time
while a disc is playing, A-B repeat playback cannot be used for that disc.
• The A-B repeat function does not operate in scenes where different
camera angles are recorded.
PLAY
REC
PAUSE/STILL
STOP
TAPE
SPEED
DPSS
SKIP
SLOW
AUDIO
OUTPUT
CH
VCR
DVD
• The A-B repeat function cannot be used on VIDEO CDs with PBC
mode playback.
• Repeat playback cannot be used during programmed playback.
VCR/DVD COMBINATION
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
97
DVD
VIDEO
C D
C D
Resume Function
This function enables you to resume the playback from the location
you specify.
1
Press ËSTOP at the desired point during playback.
• “RESUME” appears followed by “RESUME” on the screen.
• This product stores the location where you stopped.
G-CODE
PROG
DV- NC70W
DV- NC70
DV- NC70X
DVD
RESUME
TIMER
OPERATE
DISPLAY
ON/OFF
EJECT
To CANCEL RESUME PLAY
PRESS STOP
ON
VCR/DVD VCR MENU
SCREEN SELECTOR DVD SETUP
FUNCTION PROG/
CONTROL REPEAT
OPEN/
CLOSE
ANGLE
2
Press ûPLAY to restart play.
• Play resumes from a point slightly before the point where it
was stopped.
TITLE
DVD MENU
CLEAR
RETURN
SET
ENTER
• Press ûPLAY to resume disc play, if auto-playback starts
from the beginning of the disc when you reload the same disc
after removing it.
ZERO BACK
SKIP SEARCH
• Resume information will not be cancelled even if the power is turned
off.
• The continued playback described here may not be possible on some
discs (such as discs that automatically start playing when the disc tray
closes).
AM/PM
INPUT SELECT VCR DVD
/
REV
FWD
PLAY
• The resume operation does not work in the following cases
– VIDEO CDs with PBC mode playback.
– MP3 file playback.
REC
PAUSE/STILL
STOP
TAPE
SPEED
DPSS
SKIP
SLOW
AUDIO
OUTPUT
This resume operation is cancelled in the following cases.
• If you press ËSTOP twice.
• If you press ËSTOP during auto-playback.
• When you open the disc tray.
CH
VCR
DVD
• After enabling the Resume function.
VCR/DVD COMBINATION
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
98
when pressing
Æ
REC or TIMER
Troubleshooting
The following problems do not always denote a malfunction of this Product. Perform the checks listed below
before calling service.
■ VCR/DVD
Suggested Solution
Problem
• Is the power cord connected properly?
• No power
• Is the power cord firmly plugged into the power outlet?
• One of the safety mechanisms may be operating. In this event,
unplug the Product from the power outlet briefly and then plug it in
again.
• Are the batteries loaded correctly?
• Are the batteries flat?
• The Remote does not work.
• Is the signal emitter on the Remote pointing at the Product?
• Is the Remote too far from the Product, or is there any obstacle
between the Remote and the Product?
• Did the VCR/DVD CHANGE Switch change correctly?
• Did the VCR/DVD SELECTOR change correctly?
• No picture
• See page 2 for information (Condensation).
• DEW
■ VCR
Suggested Solution
Problem
• Cassette erasure protection tab has been removed. Use a different
cassette or place adhesive tape over the tab opening.
• Check if a cassette is loaded.
• VCR does not record.
• Cassette erasure protection tab has been removed. Use a different
cassette or place adhesive tape over the tab opening.
• Cassette is automatically ejected
ON/OFF.
• Make sure all the cables are correctly connected.
• Make sure the Product power cord is properly plugged in.
• Set the COLOUR MODE, NTSC MODE, and SYSTEM modes to
match the broadcast system and TV.
• No colour or poor TV picture during
normal viewing.
• Press CH '/ " to adjust the tracking or try a different cassette.
• The heads may be contaminated with condensed moisture or
magnetic coating from the video tape. (If this is the case, the
heads need to be cleaned. Ask the retailer or a Sharp approved
service centre.)
• Snowy picture appears on TV during
playback.
This Product has a built-in full auto head cleaning mechanism,
however, there are some environments in which head cleaning
cannot be carried out completely.
• Make sure the Product is not in pause/still mode.
• Make sure the tape has not reached the beginning or end.
• No tape movement.
• Make sure that the B/G, I, D/K, M (SYSTEM) setting is set to “M”
when setting the channels.
• Cannot receive NTSC (M)
broadcasting.
• Make sure the TV is set to the same channel as the Product radio
frequency converter output channel adjuster (CHANNEL).
• Check all connecting cables.
• No picture appears or colour is not
correct during playback.
• Set the COLOUR MODE, NTSC MODE, and SYSTEM modes to
match the tape and TV.
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
99
Troubleshooting
Problem
Suggested Solution
• Cassette cannot be loaded.
• Make sure there is no other cassette inside.
• Make sure the cassette is correctly positioned and then reinsert.
• Picture does not change even
though CH '/ "are pressed.
• Make sure the Product is not in the timer setting or clock setting
mode.
• Selected programme position does
not appear.
• The channel may have been set to be skipped.
Cancel the skip setting for that channel.
• No colour appears during video
search and the like.
• When a tape is recorded in the LP mode in the MESECAM
system, the picture is discoloured during video search, still and
similar modes. However, this does not indicate a malfunction.
• Picture is skewed.
• If a tape is recorded in the LP mode (regardless of whether it is a
MESECAM or PAL tape), the picture is skewed during video
search. However, this does not indicate a malfunction.
• NICAM sound cannot be output.
• Is NICAM set to OFF on the OSD mode?
■ DVD
Problem
Suggested Solution
• The Product is switched on but does • Have you loaded a disc?
not operate.
• Is the disc unplayable? (See pages 3 – 5.)
• Is there dew in the Product? (See page 2.)
• The playback image does not
appear.
• Are the video and audio cables connected correctly? (See pages
14 – 17.)
• No sound is produced.
• Is the disc scratched? (See page 5.)
• Is the disc dirty? (See page 5.)
• Is the disc loaded upside down?
• Is the input selector on the TV set to “VIDEO” or “AV”?
• Is the audio equipment switched on and are all the components
connected properly? (Refer to the operation manuals for your
audio equipment.)
• The sound is not Dolby Digital (5ch
or 5.1ch).
• Is the disc you are playing recorded in Dolby Digital (5ch or
5.1ch)?
• Have you set the “
DIGITAL” in “AUDIO SETUP” to
“BITSTREAM”? (See page 45.)
• The image and sound are garbled.
• Is the disc scratched? (See page 5.)
• Are vibrations from the speakers affecting the Product?
• The sound is not stable during
playback.
• Set the “COMPRESSION” in “AUDIO SETUP” to “OFF” (See page
45.)
This Product is equipped with a microprocessor. Its performance could be adversely affected by external electrical
noise or interference. If this should happen, unplug the Product and plug it in again after a few minutes.
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
100
Definition of Terms
■ VCR
Full Automatic This function automatically turns the power on and starts to playback when a tape with
Playback
the erasure protection tabs removed is inserted.
Sharp Super
Picture
Enhanced picture quality during playback.
S-VHS Simple This function facilitates S-VHS software playback. The original high picture quality of S-
Playback
VHS (horizontal resolution of 400 lines) cannot be played.
Tracking
Control
When noise appears on an image during tape playback, you can adjust the image
quality to a suitable level so as to reduce the noise.
■ DVD
Angle
Recorded onto some DVD discs are scenes which have been simultaneously shot from
a number of different angles (the same scene is shot from the front, from the left side,
from the right side, etc,). With such discs, you can select the angle on Function Control
Screen to view the scene from different angles.
Chapter
Number
These numbers are recorded on DVD discs. A title is subdivided into many sections,
each of which is numbered, and specific parts of video presentations can be searched
quickly using these numbers.
Compression
(Dolby Digital
output level)
Setting that increases the average volume of Dolby Digital audio when playing a DVD.
Digital Gamma Corrects for gradations in dark areas of images to make images clearer.
Dolby Digital
(5.1 channel)
A sound system developed by Dolby Laboratories Inc. that gives movie theater ambi-
ence to audio output when the Product is connected to a Dolby Digital 5.1 channel
processor or amplifier.
DTS
This is a digital sound system developed by Digital Theater Systems for use in cinemas.
This system uses 6 audio channels and provides accurate sound field positioning and
realistic acoustics. (By connecting a DTS Digital Surround decoder, you can also listen
to DTS Digital Surround sound.)
CINEMA
VOICE
For raising the sound of the center speaker to make the voices in a movie easier to hear.
For enjoying discs with a widespread surround sound feel.
3D Virtual
Surround
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
101
Definition of Terms
This refers to a high-density optical disc on which high-quality pictures and sound have
DVD
been recorded by means of digital signals. Incorporating a new video compression
technology (MPEG II) and high-density recording technology, DVD enables esthetically
pleasing full-motion video to be recorded over long periods of time (for instance, a
whole movie can be recorded).
DVD has a structure consisting of two 0.6 mm thin discs which are adhered to each
other. Since the thinner the disc, the higher the density at which the information can be
recorded, a DVD disc has a greater capacity than a single 1.2 mm thick disc. Since the
two thin discs are adhered to each other, there is the potential to achieve double-sided
play sometime in the future for even longer duration play.
Letter Box
Screen size that cuts off the top and bottom of the image to allow playing of Wide (16:9)
software on a connected 4:3 TV.
4:3 LB
Linear PCM
Sound
Linear PCM is a signal recording format used for audio CDs.
The sound on audio CDs is recorded at 44.1 kHz with 16 bits. (On DVD discs, sound is
recorded at between 48 kHz with 16 bits and 96 kHz with 24 bits.)
Pan Scan
Screen size that cuts off the sides of the image to allow playing of Wide (16:9) software
on a connected 4:3 TV.
4:3 PS
Pickup
Laser device that reads the data from a disc for playback.
Playback
This is recorded on a VIDEO CD (version 2.0). The scenes or information to be viewed (or
Control (PBC) listened to) can be selected interactively with the TV monitor by looking at the menu shown
on the TV monitor.
Region
Number identifying a geographic region of compatibility for a DVD.
<Only for DV-NC70W, DV-NC70>
The list of the region number 3 countries
Common names
Names of Nations and Areas
Brunei Darussalam
Kingdom of Cambodia
Republic of Indonesia
Republic of Korea
Lao People’s Democratic Republic
Malaysia
Union of Myanmar
Republic of the Philippines
Republic of Singapore
Kingdom of Thailand
Socialist Republic of Viet Nam
East Timor
Brunei Darussalam
Cambodia
Indonesia
Korea
Laos
Malaysia
Myanmar
Philippines
Singapore
Thailand
Viet Nam
East Timor
Hong Kong
Macau
*Hong Kong
*Macau
Taiwan
*Taiwan
*Represents area name
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
102
Definition of Terms
<Only for DV-NC70X>
The list of the region number 4 countries
Common names
Common names
Common names
Common names
Antigua and Barbuda
Argentina
Australia
Bahamas
Barbados
Belize
Guyana
Saint Vincent and the
Grenadines
Samoa
Solomon Islands
Suriname
Tonga
Trinidad and Tobago
Tuvalu
Uruguay
Vanuatu
Venezuela
Anguilla
Aruba
British Virgin Islands
Cayman Islands
Christmas Island
French Guiana
French Polynesia
Guadeloupe
Guam
Haiti
Honduras
Jamaica
Kiribati
Marshall Islands
Mexico
Micronesia
Nauru
Martinique
Montserrat
Bolivia
Netherlands Antilles
New Caledonia
Niue
Brazil
Chile
Colombia
Costa Rica
Cuba
Dominica
Dominican Republic
Ecuador
El Salvador
Fiji
Grenada
Guatemala
New Zealand
Nicaragua
Palau
Norfolk Island
Northern Mariana
Islands
Pitcairn
Tokelau
Turks and Caicos
Islands
Wallis and Futuna
Islands
Panama
Papua New Guinea
Paraguay
Peru
Saint Christopher and Cocos Islands
Nevis
Saint Lucia
Cook Islands
Falkland Islands
The world map for all region numbers
5
1
2
1
6
2
1
3
5
1
4
2
4
These are the printed lines appearing at the bottom of the screen which translate or
transcribe the dialogue. They are recorded on DVD discs.
Subtitles
This indicates the play time which has elapsed from the start of a disc or a title. It can
be used to find a specific scene quickly. (It may not work with some discs.)
Time Number
Title Menu
This is a menu displayed by some DVDs for selection of chapters and subtitle set. The
title menu is also called a “top menu”.
These numbers are recorded on DVD discs. When a disc contains two or more movies,
these movies are numbered as title 1, title 2, etc.
Title Number
Track Number
These numbers are assigned to the tracks which are recorded on VIDEO CDs and
audio CDs. They enable specific tracks to be located quickly.
This contains recordings of pictures and sound whose quality is on a par with that of
videotape. This Product also supports VIDEO CDs with playback control (version 2.0).
VIDEO CD
(VCD)
One type of audio compression that uses MPEG1.
MP3
This format compresses sound to about 1/10, without impairing the original sound
quality.
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
103
Specifications
Signal System
NTSC/PAL
DVD/VCR shared output jacks
VIDEO jack: RCA Pin-jack
AUDIO jack: RCA Pin-jack
DVD output jacks
VIDEO jack: S-Video jack
Component Y jack: RCA Pin-jack
Component PB jack: RCA Pin-jack
Component PR jack: RCA Pin-jack
AUDIO jack: RCA Pin-jack
DIGITAL AUDIO IF: Coaxial digital
AUDIO output jack: RCA Pin-jack
VIDEO jack: RCA Pin-jack
VIDEO input jacks
AUDIO jack: RCA Pin-jack
Video recording system
Video signal
Two rotary head helical scan system, VHS, Hi-Fi
PAL: PAL System-B/G, I, D/K, M (Playback/Recording)
SECAM: MESECAM System B/G, D/K, K1 (Playback/Recording)
NTSC: NTSC4.43 (Playback/Recording)
NTSC: NTSC System M (NTSC 3.58) (Playback/Recording)
720 minutes max. with E-240 tape (PAL)
480 minutes max. with T-160 tape (NTSC)
12.7mm
Recording/playing time
Tape width
Tape speed (PAL)
(SP) 23.39mm/sec
(LP) 11.70mm/sec
(EP) 7.80mm/sec
(MESECAM)
(NTSC)
(SP) 23.39mm/sec
(LP) 11.70mm/sec
(SP) 33.35mm/sec
(LP) 16.67mm/sec (Playback only)
(EP) 11.12mm/sec
75 ohm unbalanced
Antenna
Receiving channel
VHF: 1A–E12 (C1–C12), UHF: E21–E69 (C13–C57),
European CATV: S1–S41
[
DV-NC70W/70 only]
VHF: US AIR 2–13, UHF: US AIR 14–79, CATV: 2 to W+84
VHF: JAPAN 1–12, UHF: JAPAN 13–62
VHF: AU 0–13, UHF: AU 28–69 [DV-NC70X only]
NICAM-I, B/G, D/K
NICAM format
IGR stereo format
RF converter output signal
IGR-B/G, D/K
E21–E69 (adjustable), US AIR 26–38 (adjustable),
JAPAN 25–37 (adjustable). [DV-NC70W/70 only]
AU 28 - AU69 (adjustable). [DV-NC70X only]
DVD/VCR shared Video output
Component color output
Output level: 1 Vp-p (75Ω)
Y output level: 1 Vp-p (75Ω)
PB output level: 0.525 Vp-p (75Ω)/75% color
PR output level: 0.525 Vp-p (75Ω)/75% color
Y output level: 1 Vp-p (75Ω)
C output level: 0.3 Vp-p (75Ω)
Output level: 2 Vrms (1 kHz, 0 dB)
500 lines
S video output
Audio output
Video signal horizontal resolution
S/N ratio
60 dB
Audio signal frequency characteristics
For DVD linear PCM playback:
4 Hz to 22 kHz (48 kHz sampling)
4 Hz to 44 kHz (96 kHz sampling)
CD playback: 4 Hz to 20 kHz (JEITA)
CD: 96 dB, 1 kHz (JEITA)
DVD linear PCM: 96 dB (JEITA)
CD: 96 dB (JEITA)
CD: 0.006% (JEITA)
S/N ratio
Dynamic range
Total harmonic distortion ratio
Pickup
Wave length: 650 nm (DVD) / 780nm (CD)
Laser output: Max. 0.7 mW
Operating temperature
Storage temperature
Power supply
5°C to 35°C
–20°C to 55°C
110 V to 240 V AC, 50/60 Hz [DV-NC70W/70 only]
240 V AC, 50 Hz [DV-NC70X only]
Power consumption
Dimensions
Weight
23 W
430 mm × 93.5 mm × 356 mm (W × H × D)
4.8 kg
Specifications are subject to change without notice.
Weight and dimensions are approximate.
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
104
Memo
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo
Download from Www.Somanuals.com. All Manuals Search And Download.
|