Sharp Camcorder VL A110U User Manual

LIQUID CRYSTAL DISPLAY CAMCORDER

MODEL

VL A110U

OPERATION MANUAL

Please read this operation manual

carefully before using the VIEWCAM.

Important

For assistance in reporting the theft or loss of

this product, record on the line below the

model number and serial number which

are located on the bottom of the unit.

Please retain this information.

NTSC

Model No.:

Serial No.:

• See page 54 for use of Demo mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

WARNING—FCC Regulations state that any unauthorized changes or

modifications to this equipment not expressly approved by the manufacturer could

void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may

cause undesired operation.

INFORMATION

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

CAUTION ON LITHIUM BATTERY (MEMORY BACKUP BATTERY)

If a battery is reversed (positive end where the negative end belongs and vice

versa), it can overheat and rupture. This has happened when young children install

batteries backwards. Warn children not to take out batteries or install them. Parents

should install the lithium battery in the VIEWCAM.

Your VIEWCAM is designed to record in SP mode only. It will not perform normal

playback for programs prerecorded in LP mode.

This VIEWCAM does not have a PCM recording or playback function. PCM recordings made using

other VCRs or audio dubbing cannot be played back on this unit.

If you record on a tape on which PCM sound has already been recorded, the audio track of the

new VIEWCAM recording may not come out if the tape is played back on a PCM-capable VCR. If

this occurs, set the VCR’s audio monitor select switch to the “STANDARD” position.

obtained from copyright owners whenever necessary.

NOTE

The VIEWCAM’s LCD panel is a very high technology product with close to 90,000 thin-film

transistors*, giving you fine picture detail. Occasionally, a pixel may appear on the screen as a

fixed point of blue, green, red, or black. Please note that this does not affect your VIEWCAM’s

performance.

*Specifications are subject to change without notice.

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFEGUARDS

1. Read Instructions—All the safety and

operating instructions should be read

before the product is operated.

2. Retain Instructions—The safety and

operating instructions should be

retained for future reference.

3. Heed Warnings—All warnings on the

product and in the operating instruc-

tions should be adhered to.

product on a bed, sofa, rug, or other

similar surface. This product should not

be placed in a built-in installation such

as a

bookcase

or rack

unless

proper

ventilation is

4. Follow Instructions—All operating and

use instructions should be followed.

5. Cleaning—Unplug this product from the

wall outlet before cleaning. Do not use

liquid cleaners or aerosol cleaners. Use

a damp cloth for cleaning.

6. Attachments—Do not use attachments

not recommended by the product

manufacturer as they may cause

hazards.

7. Water and Moisture—Do not use this

product near water—for example, near

a bath tub, wash bowl, kitchen sink, or

laundry tub; in a wet basement; or near

a swimming pool; and the like.

8. Accessories—Do not place this product

on an unstable cart, stand, tripod,

bracket, or table. The product may fall,

causing serious injury to a child or

adult, and

provided or the manufacturer’s instruc-

tions have been adhered to.

11. Power Sources—This product should

be operated only from the type of power

source indicated on the marking label. If

you are not sure of the type of power

supply to your home, consult your

product dealer or local power company.

For products intended to operate from

battery power, or other sources, refer to

the operating instructions.

12. Grounding or Polarization—This product

may be equipped with a polarized

alternating-current line plug (a plug

having one blade wider than the other).

This plug will fit into the power outlet

only one way. This is a safety feature. If

you are unable to insert the plug fully

into the outlet, try reversing the plug. If

the plug should still fail to fit, contact

your electrician to replace your obsolete

outlet. Do not defeat the safety purpose

of the polarized plug.

serious damage

to the product.

Use only with a

cart, stand,

tripod, bracket,

13. Power-Cord Protection—Power-supply

cords should be routed so that they are

not likely to be walked on or pinched by

items placed upon or against them,

paying particular attention to cords at

plugs, convenience receptacles, and

the point where they exit from the

product.

14. Lightning—For added protection for this

product during a lightning storm, or

when it is left unattended and unused

for long periods of time, unplug it from

the wall outlet and disconnect the

antenna or cable system. This will

prevent damage to the product due to

lightning and power-line surges.

or table recommended by the manu-

facturer, or sold with the product. Any

mounting of the product should follow

the manufacturer’s instructions, and

should use a mounting accessory

recommended by the manufacturer.

9. A product and cart

combination should be

moved with care. Quick

stops, excessive force,

and uneven surfaces

may cause the product

and cart combination to overturn.

10. Ventilation—Slots and openings in the

cabinet are provided for ventilation and

to ensure reliable operation of the

product and to protect it from overheat-

ing, and these openings must not be

blocked or covered. The openings

should never be blocked by placing the

iii

Download from Www.Somanuals.com. All Manuals Search And Download.

15. Power Lines—An outside antenna

system should not be located in the

vicinity of overhead power lines or other

electric light or power circuits, or where

it can fall into such power lines or

circuits. When installing an outside

antenna system, extreme care should

be taken to keep from touching such

power lines or circuits as contact with

them might be fatal.

16. Overloading—Do not overload wall

outlets, extension cords, or integral

convenience receptacles as this can

result in a risk of fire or electric shock.

17. Object and Liquid Entry—Never push

objects of any kind into this product

through openings

f. When the product exhibits a distinct

change in performance—this

indicates a need for service.

20. Replacement Parts—When replacement

parts are required, be sure the service

technician has used replacement parts

specified by the manufacturer or have

the same characteristics as the original

part. Unauthorized substitutions may

result in fire, electric shock, or other

hazards.

21. Safety Check—Upon completion of any

service or repairs to this product, ask

the service technician to perform safety

checks to determine that the product is

in proper operating condition.

22. Wall or Ceiling Mounting—The product

should be mounted to a wall or ceiling

only as recommended by the manufac-

turer.

as they may touch

dangerous

voltage points or

short-out parts

that could result in

a fire or electric shock. Never spill liquid

of any kind on the product.

23. Heat—The product should be situated

away from heat sources such as

radiators, heat registers, stoves, or

other products (including amplifiers)

that produce heat.

18. Servicing—Do not attempt to service

this product yourself as opening or

removing covers may expose you to

dangerous voltage or other hazards.

Refer all servicing to qualified service

personnel.

19. Damage Requiring Service—Unplug

this product from the wall outlet and

refer servicing to qualified service

personnel under the following condi-

tions:

a. When the power-supply cord or plug

is damaged,

b. If liquid has been spilled, or objects

have fallen into the product,

c. If the product has been exposed to

rain or water,

d. If the product does not operate

normally by following the operating

instructions. Adjust only those

controls that are covered by the

operating instructions as an im-

proper adjustment of other controls

may result in damage and will often

require extensive work by a qualified

technician to restore the product to

its normal operation,

e. If the product has been dropped or

damaged in any way, and

Download from Www.Somanuals.com. All Manuals Search And Download.

Precautions

• When the VIEWCAM is not in use,

remember to remove the cassette tape,

turn off the power, and disconnect the

VIEWCAM from the power source.

• Always respect prohibitions or restrictions

on the use of electronic equipment on

commercial flights or in other sensitive

areas.

• Do not aim the lens at the sun.

Do not allow direct sunlight to strike the

VIEWCAM lens or LCD monitor screen,

whether or not recording is in progress, as it

may damage the CCD sensor or LCD screen

surface. Be particularly careful when

recording outside.

• Be aware of the temperature and humidity.

You can use your VIEWCAM at 0ЊC to

40ЊC

(32ЊF to 104ЊF), and at 30% to 80% relative

humidity. Do not store the unit in an

unventilated car in the

summer, in direct

sunlight, or near strong

heat sources; this can

• When shooting in dark places, avoid sudden

brightly lit objects or light sources, such as

the sun. Otherwise, the image may white out.

Should this happen, point the lens in a

different direction until the picture returns to

normal.

result in severe damage

to the unit casing and

circuitry.

• Avoid situations where water, sand, dust or

other foreign matter could get on or inside

the VIEWCAM, and do not use or leave

your VIEWCAM in areas with excessive

smoke, steam or moisture.

Such environments can

• Avoid magnetic

sources.

Using the VIEWCAM

near strong fluorescent

lights, motors,

cause malfunctions or

cause mildew to form

televisions, or other

magnetic sources may adversely affect

recorded images.

on the lenses. Be sure

to keep the unit in a

well-ventilated location.

• Using the VIEWCAM near a broadcasting

station or other powerful transmission

source may cause buzzing or picture

deterioration.

• Some small, portable

tripods may be difficult to

attach and may not be

sturdy enough to support

your VIEWCAM. Be sure to

use only a strong, stable

tripod.

• Avoid shocks and

dropping.

Do not drop or otherwise

subject the VIEWCAM to hard

shocks or strong vibrations.

Bumping or striking the unit

during recording will

generate noise in the

recorded image.

• When using your VIEWCAM in a cold

environment, the LCD monitor screen often

appears less bright immediately after the

power is turned on.This is not a

malfunction.To prevent the VIEWCAM from

becoming too cold, wrap it in a thick cloth

(a blanket, etc.).

• Avoid placing the

VIEWCAM in close

proximity to lighting

equipment.

The heat from

incandescent lights

may deform the

VIEWCAM, or cause it

to malfunction.

Download from Www.Somanuals.com. All Manuals Search And Download.

AC Adapter

LCD Monitor Screen

• The AC adapter may interfere with reception if

used near a radio.

• Prevent flammables, liquids, and metal

objects from entering the adapter.

• The adapter is a sealed unit. Do not attempt

to open or modify it.

• Do not damage, drop, or subject the adapter

to vibration.

• Do not leave the adapter in direct sunlight.

• Avoid using the adapter in humid or

extremely hot places.

The VIEWCAM is equipped with a large LCD

monitor screen that allows you to record

scenes while comfortably holding the

camcorder. The LCD monitor screen can be

rotated for easy recording at high or low

angles. It also functions as a handy playback

monitor so you can enjoy what you have just

recorded.

Cautions:

• Do not apply pressure to the screen.

• Do not expose the screen to shocks, as it may

break.

Cleaning

• Do not place the VIEWCAM with the screen

facing down.

• Many plastic parts are used in the VIEWCAM

casing. Do not use thinner, benzene or other

strong chemical cleaners. These may cause

discoloration and damage to the casing.

• Clean the casing with a soft, dry cloth. If the

casing is particularly dirty, wipe the casing

with a tightly wrung cloth dampened with a

diluted, neutral detergent. Then wipe it again

with a soft, dry cloth.

Note:

• Use a soft cloth to clean the screen.

• Use a soft cloth to wipe finger marks and

other soiling off the LCD screen.

• Use a soft cloth, or compressed air and lens

paper designed for photographic lenses to

clean the lens.

Download from Www.Somanuals.com. All Manuals Search And Download.

Supplied Accessories

Audio/video cable

QCNW-1448TAZZ

or QCNW-1295TAZZ

Battery pack

*BT-H22

AC adapter

*UADP-0312TAZZ

Infrared remote control

RRMCG0085TASA

CR2025 type

lithium battery

Shoulder strap

UBNDS0010TASA

Lens cap

GCOVH1225TASA

AA battery for

remote control

* Note: The part numbers for the AC adapter and battery pack supplied with this VIEWCAM are valid

only in the U.S. and Latin America. If this VIEWCAM was purchased outside of these areas, the part

numbers may be different. Please refer to the part numbers printed on the labels of the supplied AC

adapter and battery pack.

vii

Download from Www.Somanuals.com. All Manuals Search And Download.

Optional Accessories

Standard type

battery pack

BT-H22

Extended type

battery pack

BT-H32

Accessory

shoe adapter

VR-30ADN

Sun hood

VR-60BFN

Tripod adapter

for 180° recording

VR-33FAN

Note: The listed model names are for U.S. accessories.

For optional and additional accessories, contact your local dealer, call the Sharp

Accessories and Supply Center at 1-800-642-2122, or visit SHARP’s website

(http://www.sharp-usa.com).

viii

Download from Www.Somanuals.com. All Manuals Search And Download.

Contents

Operation Summary

Part Names .......................................................... 3

Quick Reference Index ........................................ 5

Warning Indicators ............................................... 6

Preparation

Inserting and Removing the Battery Pack ........... 7

Charging the Battery Pack................................... 8

Powering the VIEWCAM from an AC Outlet........... 9

Inserting and Removing a Cassette .................. 10

Installing the Lithium Memory Battery................ 11

Selecting the Language for the On-screen

Display ............................................................. 12

Setting the Date and Time ................................. 16

Using the Hand Strap and the Lens Cap........... 17

Attaching the Shoulder Strap ............................. 17

Basic Operations

Camera Recording

Easy Camera Recording with Full Auto Mode ... 18

Zooming ............................................................. 19

Tips on Recording Positions .............................. 19

Remaining Recording Time Display .................. 20

Remaining Battery Power Display ..................... 20

Playback

Playback ............................................................ 21

Volume Control ................................................... 21

Watching the Playback on a TV ......................... 22

Video Search...................................................... 23

Still...................................................................... 23

Download from Www.Somanuals.com. All Manuals Search And Download.

Useful Features

Operations of the On-screen Controls

Using the Control Buttons............................... 24

Selecting the Mode/Menu Screens ................ 24

Adjusting the Menu Settings........................... 25

Recording the Date and Time ............................ 26

Fade In and Fade Out........................................ 27

Quick Review ..................................................... 28

Quick Return ...................................................... 29

Edit Search......................................................... 29

Gamma Brightness Compensation .................... 30

Gain-up (Cat’s Eye) ............................................ 31

Wide Screen (16:9) ........................................... 32

Macro Shots ....................................................... 32

Removing the Lens Hood .................................. 32

Self Recording ................................................... 33

Setting the VIEWCAM to Full Auto Mode ........... 35

Program Search ................................................. 36

Tape Counter Feature ........................................ 37

Using the Remote Control .................................. 39

Advanced Features

Digital Picture Effects ......................................... 40

Scene Menu (Program AE) ................................ 41

Superimposing a Title ........................................ 42

Changing the Preset Titles ................................. 43

Auto/Manual Focus ............................................ 44

White Balance Lock ........................................... 45

Manual Exposure ............................................... 46

Picture/Backlight Adjustments ........................... 47

Gamma Playback............................................... 48

Turning Off the LCD Monitor Backlight .............. 48

Editing ................................................................ 49

References

Useful Information .............................................. 50

Demonstration Mode.......................................... 54

Before Requesting Service ................................ 55

Specifications..................................................... 57

• Guía de operación rápida en español ..........................................................58

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation Summary

Part Names

For details on the use of each part, refer to the page number indicated in the

brackets.

Front view

Terminal cover

Microphone

Zoom lens

AUDIO/VIDEO jack

[pp. 22, 49]

DC IN jack [pp. 8, 9]

Speaker

When the cassette compartment door is open

Cassette holder [p. 10]

Lens hood [p. 32]

Shoulder strap loop

[p. 17]

Lithium battery holder

[p. 11]

Cassette compartment door

[p. 10]

Cassette compartment door

release [p. 10]

Download from Www.Somanuals.com. All Manuals Search And Download.

Rear view

RECord START/STOP button [p. 18]

Power Zoom Wide angle/

LCD monitor screen

Telephoto control [p. 19]

VOLume control [p. 21]

Shoulder strap

loop [p. 17]

Remote sensor

[p. 39]

FADE button [p. 27]

CHARGE indicator

[p. 8]

MENU button

[p. 24]

Hand strap [p. 17]

Operation buttons [p. 24]

DISPLAY button [p. 24]

Power switch (CAMERA/VCR

select switch) [pp. 18, 21]

Bottom view

Battery compartment door release

[p. 7]

Battery compartment door

[p. 7]

Tripod socket

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation Summary

Quick Reference Index

This index lists some example uses of the VIEWCAM’s features.

• To quickly check what you have just recorded.

—See page 28 (Quick Review)

• To quickly return the tape to the end of the last recorded scene after playback.

—See page 29 (Quick Return)

• To locate the point on the tape where to begin recording while in Camera mode.

—See page 29 (Edit Search)

• To record a backlit subject.

—See page 30 (Gamma Brightness Compensation) or page 46 (Manual

Exposure)

• To record in a dark or poorly-illuminated location.

—See page 31 (Gain-up)

• To record yourself while monitoring the shot.

—See page 33 (Self Recording)

• To record a short video message for somebody.

—See page 34 (Self-recording Message)

• To find the beginning of a recorded scene to be played back.

—See page 36 (Program Search)

• To display the elapsed recording or playback time.

—See page 37 (Tape Counter Feature)

• To focus on an off-centered subject.

—See page 44 (Manual Focus)

• To increase the brightness of the subject during playback.

—See page 48 (Gamma Playback)

Download from Www.Somanuals.com. All Manuals Search And Download.

Warning Indicators

Displayed for the first

3 seconds

Displayed after

3 seconds

Description of warning

The video cassette is defective and should be

removed (see page 10).

Dew has formed inside the VIEWCAM. Wait for a few

hours until the dew disappears (see page 51).

About 10 seconds after this warning appears, the

VIEWCAM automatically turns off.

The battery is almost depleted. Replace it with a

fully charged battery pack (see page 7).

The video heads are clogged and should be

cleaned (see page 51).

There is no video cassette in the VIEWCAM. Insert a

cassette (see page 10).

The erasure protect tab on the video cassette has

been slid to the record-protect position, preventing

recording (see page 53).

The tape is about to end. Prepare a new cassette

(see page 10).

The tape has reached the end. Replace it with a

new cassette (see page 10).

In Self Recording mode, all warnings will be

indicated by

displayed in the center of the

monitor. To check the type of warning, rotate the

monitor back to the normal position.

Note:

indicates a flashing display.

Download from Www.Somanuals.com. All Manuals Search And Download.

Preparation

Close the door, pressing it firmly in the

center until it clicks.

Inserting and Removing the

Battery Pack

Inserting the Battery Pack

Make sure that the Power switch is set

to OFF.

Removing the Battery Pack

Power switch

Perform steps 1 and 2 above.

Slide the battery compartment door

release on the bottom of the VIEWCAM

in the direction of the arrow to open the

battery compartment door.

Press the battery release as shown to

remove the battery pack.

Battery

compartment

door release

Battery release

Insert the battery pack into the com-

partment as shown, and push it in com-

pletely until it locks into place.

Cautions:

• BEFORE REMOVINGTHE BATTERY PACK,

ALWAYS STOP THE TAPE AND TURN THE

POWER OFF. If you remove the battery pack

during recording or playback, the tape will

remain wound around the video head drum,

potentially causing damage to the tape.

• Make sure the battery compartment door is

closed firmly during operation. If it is not, the

battery pack may fall out or VIEWCAM operation

may fail because of the poor contact pressure.

• Remove the battery pack from the VIEWCAM if

the VIEWCAM will not be used for a long period

of time.

Caution:

• Do not force the battery pack into the

battery compartment if it does not go in

easily.

• When removing the battery pack, do not tilt

the VIEWCAM so that the battery compart-

ment faces down.The battery pack may fall

out.

• Do not expose the battery compartment door to

strong force, as it may come off.

• Use only SHARP model BT-H22 or BT-H32

battery packs with this VIEWCAM. Use of other

batteries may present a risk of fire or explosion.

Download from Www.Somanuals.com. All Manuals Search And Download.

Charging time and maximum continuous

recording and playback times

Charging the Battery Pack

Power switch

Max.

Battery Charging continuous continuous

pack

time

recording

time

playback

time

approx.

3 hr.

approx.

BT-H22

BT-H32

1 hr. 35 min. 1 hr. 35 min.

approx.

6 hr.

approx.

3 hr. 10 min. 3 hr. 10 min.

approx.

CHARGE indicator

Notes:

Insert the battery pack into the VIEWCAM

(see page 7). Make sure that the Power

switch is set to OFF.

• Using the zoom (see page 19) and other

functions or turning the power on and off

frequently will increase power consumption.

This may result in a decrease of more than 50%

in the actual recording time compared to the

maximum continuous recording time listed

above.

• The charging time and recording time may vary

depending on the ambient temperature and the

condition of the battery pack.

• It is recommended that you have enough battery

packs on hand to provide two to three times your

estimated recording time.

• See page 52 for more information on using the

battery pack.

• The battery pack will not charge when the

Power switch is set to CAMERA or VCR.

Insert the AC plug of the AC adapter into a

power outlet.

Open the terminal cover on the VIEWCAM

and insert the DC plug of the AC adapter

into the DC IN jack on the VIEWCAM.

• The CHARGE indicator will light up in red.

Terminal cover

Caution:

• Charge only SHARP model BT-H22 or BT-H32

battery packs. Other types of battery packs may

burst, causing personal injury and damage.

DC IN jack

To power

outlet

When the battery is fully charged, the

CHARGE indicator will light up in green.

Remove the DC plug from the VIEWCAM,

and close the terminal cover.

Caution:

• When removing the plugs, grasp the plug, not the

cable.

Download from Www.Somanuals.com. All Manuals Search And Download.

Preparation

Cautions:

Powering the VIEWCAM from

an AC Outlet

• BEFORE REMOVING THE DC PLUG, ALWAYS

STOP THE TAPE AND TURN THE POWER OFF.

If you remove the DC plug during recording or

playback, the tape will remain wound around the

video head drum, potentially causing damage to

the tape.

• Remove the DC plug from the VIEWCAM if you

will not use the VIEWCAM for a long period of

time.

Caution:

• The supplied AC adapter is specially designed

for use with this VIEWCAM, and should not be

used as a power supply for other camcorders.

• When removing the plugs, grasp the plug, not

the cable.

Note:

• Close the terminal cover after use.

Power switch

Insert the AC plug of the AC adapter into

a power outlet.

Make sure that the Power switch is set

to OFF.

Open the terminal cover and insert the

DC plug of the AC adapter into the DC

IN jack on the VIEWCAM.

Terminal cover

DC IN jack

To power

outlet

Hold down the Lock

button and slide the

Power switch to

CAMERA or VCR.

Lock button

Download from Www.Somanuals.com. All Manuals Search And Download.

Wait for the cassette holder to fully

retract. Close the compartment door by

pressing the center until it clicks into

place.

Inserting and Removing a

Cassette

Inserting a Cassette

Supply power to the VIEWCAM, then

slide the release and open the cassette

compartment door.

• The cassette holder extends and opens

automatically.

Cassette compartment

door release

Removing a Cassette

Perform step 1 above, then take out the

cassette.

Cautions:

• Do not try to close the cassette compartment

door while the cassette holder is extending or

retracting.

• Be careful not to get your fingers caught in the

cassette holder.

• Do not apply force to the cassette holder except

when pressing the PUSH mark to close it.

• Do not tilt the VIEWCAM or hold it upside down

when you are inserting or removing a cassette. It

may damage the tape.

Insert the cassette fully with the window

facing outwards, and with the erasure

protect tab facing upwards.

Erasure protect tab

• Remove the cassette if you will not use the

VIEWCAM for a long period of time.

• If you do not correctly close the cassette holder

in step 3, the VIEWCAM’s cassette protection

mechanism might eject the cassette. If this

happens, repeat the insertion procedure.

• Do not attempt to pick up the VIEWCAM by the

cassette compartment door.

Notes:

• If the battery power is too low, you may not be

able to eject the cassette. Replace the battery

pack with a fully charged one.

• See page 53 for more information on the video

cassette tapes for use with this VIEWCAM.

Press the PUSH mark gently until the

cassette holder clicks into place.

• The cassette holder retracts

automatically.

PUSH mark

Download from Www.Somanuals.com. All Manuals Search And Download.

Preparation

Close the cassette compartment door by

pressing the center until it clicks into

place.

Installing the Lithium

Memory Battery

The supplied lithium battery is used to store the

memory of the date and time settings.

Slide the cassette compartment door

release and open the cassette

compartment door.

Cassette compartment

door release

Removing the Lithium Battery

Perform steps 1 and 2 above, then lift out the

battery from the battery holder.

Note:

• Replace the battery with a new CR2025 battery

when the date and time indicator starts to fall

behind the correct time.

Notes on the Use of the Lithium

Battery

Note: The cassette holder will extend and

open when the VIEWCAM is connected to a

power source. Be sure to close the cassette

holder before proceeding to the next step

(see page 10).

REPLACE BATTERY WITH TOSHIBA,

MATSUSHITA OR HITACHI MAXELL TYPE

CR2025 ONLY. USE OF A DIFFERENT

BATTERY MAY PRESENT A RISK OF FIRE OR

EXPLOSION.

Pull out the lithium battery holder using

a pointed object such as the tip of a

ballpoint pen.

WARNING KEEP THIS BATTERY AWAY FROM

CHILDREN. IF SWALLOWED, CONSULT A

PHYSICIAN IMMEDIATELY FOR EMERGENCY

TREATMENT.

CAUTION BATTERY MAY EXPLODE IF MIS-

USED OR INSTALLED WITH POLARITY

REVERSED. DO NOT RECHARGE, DISAS-

SEMBLE OR DISPOSE OF IN FIRE.

• Do not short-circuit, recharge, disassemble,

or heat the lithium battery.

Lithium battery holder

• Should the lithium battery leak, wipe the

battery compartment and holder clean, and

then insert a new battery.

• The lithium battery will last about one year of

normal usage.

Insert the lithium battery

into the battery holder with

the ` side of the battery

facing the j side of the

holder.

j mark

Push the battery holder back

into position.

Download from Www.Somanuals.com. All Manuals Search And Download.

Changing the Language

Selecting the Language for

the On-screen Display

In Recording Standby mode, press the

MENU button until appears.

This VIEWCAM allows you to choose from

among English, French or Spanish for the on-

screen display language.

Press the PAGE (PAGE or PAGINA)

button ( ) to display MENU 1.

Power switch

Press the ĭ or İ button (Q) to select

“LANGUAGE” (“LANGUE” or “IDIOMA”),

then press the SET (REGLAGE or

AJUSTE) button (B) (W).

• The language selection screen appears.

MENU button

FADE

NORMAL

OFF

REMOTE

SET

Operation buttons

DEMO MODE

LANGUAGE

Setting the Language

PI C

When using the VIEWCAM for the first time,

select the desired language for the on-screen

display by performing the procedure below.

SET TURE PAGE

Press the ĭ or İ button (C or D) (Q)

to select the desired language, then

press the AJUSTE (SET or REGLAGE)

button (B) (W).

Lock button

Hold down the Lock

button and slide the

Power switch to

• The menu screen is displayed in the

CAMERA.

language selected.

• The language selection

screen appears.

I DI OMA

ENGL I SH

AJUS

FRAN AI S

Press the ĭ or İ button (C or D) (Q)

to select the desired language, then

press the SET (REGLAGE or AJUSTE)

button (B) (W).

ESPAÑOL

LANGUAGE

ENGL I SH

FRAN AI S

SET

ESPAÑOL

IMA

REV

GAM RAP

SET

Press the DISPLAY button to turn off the

menu screen.

Note:

• The operation procedures in the following

sections of this operation manual are based

on the use of on-screen displays in English.

PI C

EFF

GAMA QK

EFF REW

Download from Www.Somanuals.com. All Manuals Search And Download.

Preparation

English On-screen Displays

The following on-screen displays appear when “ENGLISH” is selected as the on-screen

display language (see page 12).

Camera Mode

PI C

EFF

GAMA QK

EFF REW

FADE

NORMAL

REMOTE

DEMO MODE

LANGUAGE

OFF

COU

PI C

NTER

SET TURE PAGE

WH I TE EXPO

DATE/ TIME

DI SPLAY

SELECT

FOCUS

BAL.

SURE

OFF

DATE TIME

SETTI NG

JAN

12 00 AM

12H

2000

12H/ 24H

PI C

SCENE

SET TURE PAGE

TLE TURN 16

VCR Mode

EDI T

REMOTE

OFF

REW PLAY FF STOP STI LL

PI C

GAMA COU

SET TURE

EFF. NTER

ARCH

13 Note: See pages 24 and 25 for the procedure to display the desired screen.

Download from Www.Somanuals.com. All Manuals Search And Download.

French On-screen Displays

The following on-screen displays appear when “FRANÇAIS” is selected as the on-

screen display language (see page 12).

Camera Mode

IMAGE

EFF. REVU

GAMM RAP.

FONDU

NORMAL

TELECOM.

MODE DEMO

LANGUE

OFF

COMP

TEUR

REG

LAGE IMAGE PAGE

BAL.

EXPO

DATE/ HEURE

FOCUS

BLANC SI T.

AFFI CHAGE OFF

SELECT I ON DATE HEURE

REGLAGE

12H/ 24H

JAN

12 00 AM

12H

2000

REG

SCENE

LAGE IMAGE PAGE

TRE TOUR 16

VCR Mode

MONTAGE

REM

LEC

AV.

OFF

BOBIN TURE RAP. ARRET FI XE

TELECOM.

REG

EFF. COMP

GAMM TEUR

RECH

LAGE IMAGE

ERCHE

Download from Www.Somanuals.com. All Manuals Search And Download.

Preparation

Spanish On-screen Displays

The following on-screen displays appear when “ESPAÑOL” is selected as the on-

screen display language (see page 12).

Camera Mode

EF.

IMA.

EF.

REV.

GAM. RAP.

DESVANECER NORMAL

DI STANCI A

ENCENDIDO

MODO DEMOS. APAGADO

I DI OMA

CON

AJUS IMA

TAD.

GEN GI NA

BAL.

BCO

ENFO

FECHA/ HORA

VI SUALI.

PO.

QUE

APAGADO

SELECCI ON FECHA HORA

AJUSTE

ENE

2000

12 00 AM

12H

12H/24H

AJUS IMA

T I

ESCE.

GEN GI NA

TULO TOR. 16

VCR Mode

AVA.

EDI CION

APAGADO

BO. PRO. RAP. PARAR FI JA

DI STANCI A ENCENDI DO

AJUS IMA

EF.

CON

BUS

TE GEN

GAM. TAD.

CAR

Download from Www.Somanuals.com. All Manuals Search And Download.

Press the ĭ or İ button (C or D) to

select “JUN” (month), and press the

SET button.

Setting the Date and Time

Example: Setting the date to June 2, 2001

(JUN. 2. 2001) and the time to 10:30 am (10:30

AM).

JUN 1 2000

12 00 AM

Note:

Press the ĭ or İ button to select “2”

• Check that the lithium memory battery has been

installed before setting the date and time.

(day), and press the SET button.

JUN 2 2000

12 00 AM

Power switch

Press the ĭ or İ button to select

“2001” (year), and press the SET button.

JUN 2 2001

12 00 AM

Press the ĭ or İ button to select “10

AM” (hour), and press the SET button.

MENU button

DISPLAY button

Lock button

JUN 2 2001

10 00 AM

Hold down the Lock

button and slide the

Power switch to

CAMERA.

Press the ĭ or İ button to select “30”

(minute), and press the SET button.

• The internal clock now starts operating.

JUN 2 2001

10 30 AM

Press the MENU button until

(MENU 2) appears.

Press the DISPLAY button to turn off the

menu screen.

DATE/ TIME

DI SPLAY

SELECT

Changing to the 24-hour Time Mode

OFF

DATE TIME

SETTI NG

JAN

12 00 AM

12H

2000

After performing step 8 above, press the ĭ or

İ button (Q) to select “12H/24H”, then press

the SET button (B) (W) to select “24H”.

12H/ 24H

PI C

SET TURE PAGE

DATE/ TIME

DI SPLAY

SELECT

OFF

SET

DATE TIME

SETTI NG

JUN

10 30

24H

2001

• If MENU 1 appears on the

screen,

press the PAGE button ( ) to display

MENU 2.

12H/ 24H

PI C

SET TURE PAGE

Press the SET button (B).

Notes:

• The date and time, once set, are stored in

DATE/ TIME

SET

DI SPLAY

SELECT

OFF

memory.

DATE TIME

SETTI NG

JAN

12 00 AM

12H

2000

• The menu screen automatically turns off if no

settings are made within 5 minutes.

12H/ 24H

PI C

SET TURE PAGE

• When changing the date and time settings,

press the ĭ or İ button (C or D) to

select “SETTING”, then press the SET

button.

Download from Www.Somanuals.com. All Manuals Search And Download.

Preparation

Notes:

Using the Hand Strap and the

Lens Cap

• Always replace the

lens cap on the lens

when the VIEWCAM is

not in use.

• Attach the lens cap to

the hand strap so it will

not get in the way

during recording.

Open the hand strap flap (Q) and grip

strap (W), and pass the grip strap

through the loop at the end of the lens

cap cord (E).

Hand strap flap

Grip strap

Attaching the Shoulder Strap

Hold one end of the strap and thread it

through the loop on the left side of the

LCD screen.

Pass your hand through the hand strap

and put your thumb close to the Power

Zoom control. Then pull the grip strap

tight until it fits snugly, seal the Velcro^®

closures (Q), and close the hand strap

flap (W).

Loosen the strap in the buckle, then feed

the end of the strap through the buckle,

as shown.

Draw the strap in the direction of the

arrow to secure.

4–6 Use the same procedure to attach the

other end of the strap to the loop on

the lens side.

LCD screen side

Lens side

Caution:

• Do not swing the VIEWCAM by the hand strap.

Attaching and Removing the Lens Cap

When attaching or removing the lens cap,

press both tabs on the sides of the cap.

Buckle

Press both tabs.

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic Operations

Camera Recording

Note:

Easy Camera Recording with

Full Auto Mode

• When recording at the beginning of a tape, advance

the tape about 15 seconds before you begin

recording. This will prevent the beginning of the

recording being cut off when it is played back.

Before you start recording, perform the operations

described on pages 7 through 17 to prepare your

VIEWCAM for recording.

To Pause Recording

Press the REC START/STOP button again.

Recording pauses, and the VIEWCAM enters

the Recording Standby mode.

REC START/STOP button

PAUSE

LCD monitor screen

Power switch

Remove the lens cap (see page 17).

To Turn the Power Off

Hold down the Lock button and slide the

Power switch to CAMERA.

• The picture from the lens is now

displayed on the LCD monitor screen.

• The VIEWCAM is now ready to record

(Recording Standby mode).

Slide the Power switch to

OFF.

Notes:

• The speaker is off in Camera mode.

• Battery power is consumed in Recording Standby

mode. Turn off the power if you will not be recording

again soon.

Lock button

AUTO

• If the VIEWCAM is kept in Recording Standby mode

for more than approximately 5 minutes, the power

will automatically turn off to save battery power and

to protect the tape from being damaged. To

continue recording after this, set the Power switch to

OFF, and then back to CAMERA.

Maximum Continuous Recording and

Actual Recording Times

Full Auto mode indicator

Note: If, at this time, “AUTO” does not appear,

set the VIEWCAM to Full Auto mode by following

the procedure described on page 35.

Battery Max. continuous Actual recording

pack

recording time

time

approx.

1 hr. 35 min.

approx.

45 min.

Press the REC START/STOP button to

begin recording.

BT-H22

approx.

3 hr. 10 min.

approx.

1 hr. 30 min.

BT-H32

REC

Note:

• Using the zoom (see page 19) and other functions

or turning the power on and off frequently will

increase power consumption.This may result in a

decrease of more than 50% in the actual

recording time compared to the maximum

continuous recording time listed above.

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic Operations

Camera Recording

Zooming

Tips on Recording Positions

Zooming allows you to move visually closer to

or farther from a subject without physically

changing your position.

The rotating LCD monitor screen lets you enjoy

easy video recording in a more relaxed posture

without having to hold the VIEWCAM up to your

eye. The LCD monitor also makes it easier to

record high-angle and low-angle shots.

Zooming in (when you want to center

attention on the subject)

Holding the VIEWCAM

Tele-

photo

Wide

angle

Put the fingers of your right hand through the hand

strap, and place your right thumb close to the REC

START/STOP button and Power Zoom control.

Place your left thumb on the thumb rest on the left

side of the LCD monitor.

Zooming out (when you want to

show the surroundings)

Basic Posture

To Zoom In

Push the Power Zoom control to the T

(telephoto) side to get a close-up view (Q).

To Zoom Out

Push the Power Zoom control to the W (wide

angle) side to get a wide field of view (W).

Press your elbows

against your sides.

Place your feet at a

45° angle and

balance your weight

on both legs.

Power Zoom

control

High Angle

You can record while still

viewing the screen. This is

convenient when you want

to record over a crowd.

Zoom range indicator

• The on-screen display shows you the current

zoom setting.

• The zoom speed changes depending on how far

you push the Power Zoom control.

Low Angle

Put one knee on the

ground for the best

stability.

Note:

• The VIEWCAM is unable to focus when zooming

in on subjects within 5 feet (1.5 m). The

VIEWCAM will automatically zoom out until it is

able to focus on the subject. (See page 32 for

recording macro shots.)

Notes:

• In hand-held recording, the VIEWCAM has to be

steadied to prevent image shakes. For very

stable recording, use a tripod.

• Take care not to touch the microphone with your

fingers during recording. It will cause noise on

the audio track.

Download from Www.Somanuals.com. All Manuals Search And Download.

Remaining Recording Time

Display

Remaining Battery Power

Display

When the VIEWCAM is recording in Camera

mode, about 10 minutes before the tape

reaches the end, an on-screen indicator

displays the approximate remaining recording

time.

When using the VIEWCAM with the battery

pack as the power source, you can turn on and

off the remaining battery power display by

pressing the DISPLAY button.

If the battery power becomes very low, a

warning indicator will appear. Replace the

battery pack.

DISPLAY button

Approx. remaining

recording time

On-screen

indicator

DISPLAY button

(Green)

10 min.–8 min.

8 min.–6 min.

6 min.–4 min.

4 min.–2 min.

2 min.–1 min.

T A P E

Remaining battery

(Green)

power display

(Red)

Warning indicator

1 min.–0 min.

0 min.

(The tape has

reached the end.)

Notes:

• Use the remaining battery power display only as

an approximate indication.

• The battery power display may change to either

a higher or lower level if you set the Power

switch to OFF and then back to CAMERA or

VCR.

To turn off the remaining recording time display,

press the DISPLAY button.

• In cold environments, the red remaining battery

power display may appear sooner. The battery

pack, however, can be used until the warning

indicator appears. Replace the battery pack at

this time.

• Battery consumption may vary depending on the

condition of use.

• Use of the zoom function when the warning

indicator is displayed may cause the VIEWCAM

to suddenly lose power.

Notes:

• The remaining recording time displays only show

the approximate time left. Also, they vary slightly

depending on the length of tape used. (This

function’s design is based on the P6-120 tape

standard.)

• If you turn off the remaining recording time

display, it will reappear after a short interval to

indicate the new time remaining.

• The remaining recording time display appears

5 seconds after pressing the REC START/

STOP button to begin recording.

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic Operations

Playback

To Stop Playback

Playback

Press the STOP

button (A).

The LCD monitor screen makes it possible to

play back and see what you have just

recorded. Nothing needs to be connected,

allowing instant on-screen playback with the

sound through the built-in speaker.

REW PLAY FF STOP STI LL

Power switch

Notes:

LCD monitor screen

• If you wish to turn the Operation button

indicators on or off, press the DISPLAY button.

The playback operation buttons will still function

as indicated even after the indicators are turned

off.

• To use the infrared remote control, make sure

that the REMOTE menu item is set to “ON” (see

page 39).

AutoTape Rewind

DISPLAY button

The tape is automatically rewound when

playback reaches the end of the tape.

Hold down the Lock

button and slide the

Power switch

To Turn the Power Off

Slide the Power switch to OFF.

to VCR.

• The

screen appears.

Volume Control

Lock button

While the VIEWCAM is in VCR mode, push the

Volume control to the

side to increase

(Q) or decrease (W) the volume to your

preference.

Press the REW (C) (or FF [B]) button

to rewind (or fast forward) the tape to the

desired point.

The volume level indicator will appear on the

screen during adjustment only. When the

Volume control is released, the volume level

indicator will disappear shortly afterwards.

REW PLAY FF STOP STI LL

Press the PLAY button (D) to begin

playback.

REW PLAY FF STOP STI LL

Volume control

Decrease

Increase

Download from Www.Somanuals.com. All Manuals Search And Download.

Turn on the TV and set it to the “AV” or

“VIDEO” channel. (See the operation

manual of your TV.)

• When connecting to a TV via a VCR, turn on

the VCR and set it to the “AV” or “LINE”

input channel. Operate the TV as you

normally do to see the signal from the VCR.

(See the operation manuals of your TV and

VCR.)

Watching the Playback on a

You can also connect the VIEWCAM to a TV to

allow a larger audience to enjoy video

playback.

Lift up the terminal cover on the

VIEWCAM (Q) and rotate it to the right

(W).

Turn on the VIEWCAM in VCR mode,

and begin tape playback (see page 21).

Terminal cover

Caution:

• Make sure that the VIEWCAM, TV, VCR and other

equipment to be connected have been turned

off before you make connections. Making con-

nections with any of the components left turned

on may cause picture noise or a malfunction.

Notes:

• This VIEWCAM does not have an S-video

socket.

Connect the VIEWCAM to your TV (or

VCR) with the supplied audio/video

cable, as shown.

• When the VIEWCAM is connected to a TV for

playback, the picture on the TV screen may

flicker if the volume on the VIEWCAM is set to

maximum. Should this occur, turn the volume

down (see page 21).

• Close the terminal cover after use.

CHANNEL

AUSE

/STILL

PLAY

STOP/

EJECT

POWER

REC

Yellow: To VIDEO IN jack

White: To AUDIO IN (L) jack

Audio/video cable

(supplied)

To AUDIO/VIDEO jack

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic Operations

Playback

Video Search

Still

The video search function makes it easy to

search for a desired scene on the tape.

The still function makes it possible to pause

playback.

During playback, press the STILL button ( ).

Searching for a Scene Near the Current

Tape Position

During playback, press the Forward

Search (B) (or Reverse Search [C])

button.

REW PLAY FF STOP STI LL

• The playback picture fast forwards (or

reverses).

To return to normal playback, press the

STILL button again or press the PLAY

button (D).

REW PLAY FF STOP STI LL

Notes:

• The sound is off during Still mode.

• To protect the tape, the VIEWCAM automatically

returns to normal playback if it is left in Still mode

for more than 5 minutes.

• If the still function is used when connected to a

TV, noise will appear and distort the playback

image.

Forward Search button

Reverse Search button

When you find the desired scene, press

the PLAY button (D) to return to normal

playback.

Searching for a Scene Far from the

Current Tape Position

During fast forward (or rewind), press

and hold down the Forward Search (B)

(or Reverse Search [C]) button.

• The fast forward (or reverse) playback

picture is displayed.

If the desired scene is still rather far

from the current tape position, release

the button to return to normal fast

forward (or rewind).

Repeat steps 1 and 2 above until you

find the desired scene.

Press the STOP button (A) and then

the PLAY button (D) to begin normal

playback.

Notes:

• The sound is off during search.

• Some picture noise appears during search. This

is not a malfunction.

Download from Www.Somanuals.com. All Manuals Search And Download.

Useful Features

Selecting the Mode/Menu

Screens

Operations of the On-screen

Controls

You can use the mode screens to select

various functions and the menu screens to

adjust various settings. Follow the procedure

below to display the mode/menu screen with

the indicator of the desired function/setting.

Using the Control Buttons

The following buttons on the VIEWCAM can be

used to control the various functions, settings

and on-screen displays.

Hold down the Lock

button and slide the

Power switch to

CAMERA (Camera

mode) or VCR (VCR

mode).

Lock button

Press the MENU button until the desired

screen appears.

MENU button

DISPLAY button

Camera mode

Operation buttons

MENU button

PI C

EFF

GAMA QK

EFF REW

Each time you press the MENU button,

the mode/menu screen changes from

in Camera mode and from

in VCR mode.

COU

NTER

DISPLAY button

Press the DISPLAY button to turn the

mode/menu screens and on-screen

indicators on or off.

WHI TE EXPO

BAL.

SURE

FOCUS

Note:

• The warning indicators and some other

indicators cannot be turned off by pressing the

DISPLAY button.

SCENE

TLE TURN 16

Operation buttons

PI C

Press the Operation button corresponding to

the indicator of the desired function displayed

on the screen.

SET TURE PAGE

VCR mode

REW PLAY FF STOP STI LL

Note:

• The Operation button indicators are normally

displayed in blue or gray. When a function is

selected, its indicator is displayed in yellow.

GAMA COU

EFF. NTER

ARCH

PI C

SET TURE

Download from Www.Somanuals.com. All Manuals Search And Download.

Useful Features

Press the SET button (B) to select the

desired setting.

Adjusting the Menu Settings

• Each time you press the SET button, the

setting changes.

Follow the procedure below to adjust the

desired menu settings.

Example

Camera mode

SET

Hold down the Lock button and slide the

Power switch to CAMERA.

FADE

REMOTE

DEMO MODE

NORMAL

OFF

Press the MENU button until

appears.

NORMAL

HOL I DAY

B I RTHDAY

PI C

Press the DISPLAY button to turn off the

menu screen.

SET TURE PAGE

VCR mode

Press the PAGE button ( ) to display the

desired menu screen.

• Each time you press the PAGE button,

the screen changes between MENU 1

and MENU 2.

Hold down the Lock button and slide the

Power switch to VCR.

Press the MENU button until

appears.

PAGE

FADE

NORMAL

OFF

REMOTE

EDI T

OFF

DEMO MODE

LANGUAGE

REMOTE

PI C

SET TURE PAGE

PI C

SET TURE

DATE/ TIME

DI SPLAY

SELECT

Perform steps 4 to 6 above.

OFF

DATE TIME

SETTI NG

JUN

10 30 AM

12H

2001

Notes:

12H/ 24H

• Certain menu items are common in both Camera

and VCR modes. If the REMOTE menu item, for

example, is set to “OFF” in Camera mode, it will

be automatically set to “OFF” in VCR mode.

• The menu screen automatically turns off if no

settings are made within 5 minutes.

PI C

SET TURE PAGE

Press the ĭ or İ button (C or D) to

select the desired menu item.

Example

SET

FADE

NORMAL

OFF

REMOTE

DEMO MODE

LANGUAGE

Download from Www.Somanuals.com. All Manuals Search And Download.

When “AUTO” is selected, the date/time

is displayed and recorded for 10

seconds at the beginning of the first

recording of each day.

When “ON” is selected, the date/time is

continuously displayed and recorded.

When “OFF” is selected, the date/time is

neither displayed nor recorded.

Recording the Date and Time

Follow the procedure shown below to record

the date and time, or the date only, along with

the subject.

Note:

• Before performing the procedure below, make

sure that the date and time have been correctly

set (see page 16).

Note: In “AUTO”, if you wish to record the

date/time a second time that day, repeat the

procedure above and re-select “AUTO”.

In Recording Standby mode, press the

MENU button until

(MENU 1)

Press the ĭ button to select “SELECT”.

appears.

SET

DATE/ TIME

Press the PAGE button ( ) to display

MENU 2.

DI SPLAY

SELECT

AUTO

DATE TIME

SETTI NG

JUN

2001

10 30 AM

12H

12H/ 24H

DATE/ TIME

DI SPLAY

SELECT

OFF

PAGE

DATE TIME

Press the SET button (B) to select

“DATE+TIME” or “DATE”.

SETTI NG

JUN

10 30 AM

12H

2001

12H/ 24H

PI C

SET TURE PAGE

SET

DATE/ TIME

DI SPLAY

SELECT

AUTO

DATE TIME

Press the ĭ or İ button to select

“DISPLAY”.

When “DATE+TIME” is selected, both the

date and the time are displayed and

recorded.

When “DATE” is selected, only the date

is displayed and recorded.

SET

DATE/ TIME

DI SPLAY

SELECT

OFF

DATE TIME

SETTI NG

JUN

10 30 AM

12H

2001

12H/ 24H

Press the DISPLAY button to turn off the

menu screen, and then press the REC

START/STOP button to begin recording.

Press the SET button (B) to select

“AUTO”, “ON”, or “OFF”.

SET

DATE/ TIME

DI SPLAY

SELECT

JUN

2001

OFF

10 30 AM

DATE TIME

Download from Www.Somanuals.com. All Manuals Search And Download.

Useful Features

Selecting Fade Mode

Fade In and Fade Out

In Recording Standby mode, press the

The fade function allows you to gradually bring

the image and sound in or out at the beginning

or end of a scene to create a scene transition.

This VIEWCAM features one normal and two

animated fade modes.

MENU button until

(MENU 1)

appears.

FADE

NORMAL

OFF

REMOTE

DEMO MODE

LANGUAGE

Type of Fade Modes

NORMAL: The picture fades in from and out to

white.

PI C

SET TURE PAGE

HOLIDAY: The picture fades in from an

animated firework sequence with the title

“HAPPY HOLIDAYS!”, and fades out to white.

Press the ĭ or İ button (Q) to select

“FADE”, then press the SET button (B)

(W) to select the desired fade mode.

HAPPY HOL I DAYS!

SET

FADE

NORMAL

REMOTE

DEMO MODE

OFF

NORMAL

HOL I DAY

B I RTHDAY

Press the DISPLAY button to turn off the

menu screen.

HAPPY HOL I DAYS!

BIRTHDAY: The picture fades in from an

animated birthday cake sequence with the

title “HAPPY BIRTHDAY!”, and fades out to

white.

Using Fade Mode

In Recording Standby mode, press the

FADE button.

• The selected fade mode indicator

appears. (“FADE” is displayed for the

NORMAL fade mode indicator.)

Fade mode indicator

HAPPY BI RTHDAY!

BI RTHDAY

PI C

EFF

GAMA QK

EFF REW

HAPPY BI RTHDAY!

Download from Www.Somanuals.com. All Manuals Search And Download.

Press the REC START/STOP button to

begin recording.

Quick Review

• The picture and sound fade in with the

selected fade mode.

The quick review function lets you check the

last 5 seconds of tape just recorded without

switching to VCR mode, to make sure that the

recording has come out right.

In Recording Standby mode, press the

MENU button until

appears.

HAPPY BI RTHDAY!

PI C

EFF

GAMA QK

EFF REW

Press the QK. REW button ( ).

FADE

• The tape rewinds to the point of 5

seconds before the current tape position;

playback then starts automatically.

PI C

EFF

GAMA QK

EFF

REW

Press the REC START/STOP button at

the point where you wish to stop

recording.

PI C

EFF

GAMA QK

EFF REW

• The picture and sound fade out as the

screen gradually turns white. The

VIEWCAM then returns to Recording

Standby mode.

After 5 seconds of playback, the

VIEWCAM enters the Recording Standby

mode.

FADE OUT

PI C

EFF

GAMA QK

EFF

REW

To cancel Fade mode

Press the FADE button.

To use fade out only

During recording, press the FADE

button.

Press the REC START/STOP button at

the point where you wish to stop

recording.

Download from Www.Somanuals.com. All Manuals Search And Download.

Useful Features

Quick Return

Edit Search

When you have been playing back what you

have recorded, and wish to quickly return to

recording again from the end of the last

The edit search function lets you search,

without switching from Camera mode to VCR

mode, for the point on the tape where you wish

to start recording next.

recorded scene, use the quick return function.

In Recording Standby mode, press the

MENU button until

appears.

SCENE

TLE TURN 16

Reverse Edit

Search button

Press the RETURN button (D).

DISPLAY button

• “QUICK RETURN” flashes, and the tape

will begin fast forwarding or rewinding to

the end of the last recorded scene.

Forward Edit Search button

In Recording Standby mode, make sure

that no Operation button indicators are

displayed on the monitor.

• If they are displayed, turn them off by

pressing the DISPLAY button.

TURN

QUI CK RETURN

RE-

SCENE

Press and hold down the Forward Edit

Search button (B) or Reverse Edit

Search button (C).

TLE TURN 16

When the tape reaches the end of the last

recorded scene, the VIEWCAM enters the

Recording Standby mode.

Forward edit

Notes:

• To cancel the quick return function, press the

RETURN button again in step 2.

Reverse edit

• If the cassette has been removed since the last

recording, if no recording has been made since

the cassette was loaded, or if the power source

has been interrupted, the RETURN button

indicator will not appear and the quick return

function cannot be used.

When you find the point where you want

to begin recording, release the button.

Notes:

• The sound is off during search.

• Some picture noise appears during reverse edit

search.

• Forward edit search is performed at the same

speed as normal playback, and reverse edit

search at three times the normal playback

speed.

Download from Www.Somanuals.com. All Manuals Search And Download.

To obtain a brighter picture

Gamma Brightness

Compensation

Press the GAMA EFF. button (A) again.

• The

indicator appears.

When the subject is backlit, the image will be

darkened if it is recorded normally. The gamma

brightness compensation function improves the

picture by increasing the brightness of the

subject while leaving the brighter portions of

the image unaffected.

GAMA

EFF.

GAMMA

PI C

EFF

GAMA QK

EFF REW

Press the MENU button until

appears (Camera mode).

Note:

• When the

indicator is displayed, the

background will become slightly brighter.

Press the GAMA EFF. button (A) once.

• “GAMMA” appears, indicating that the

Gamma Brightness Compensation is

now working.

To cancel Gamma Brightness

Compensation

GAMA

EFF.

Press the GAMA EFF. button until “GAMMA”

disappears.

PI C

EFF

GAMA QK

EFF REW

GAMMA

PI C

EFF

GAMA QK

EFF REW

Note:

• The gamma brightness compensation function

can also be used during playback. See page 48,

“Gamma Playback”.

Download from Www.Somanuals.com. All Manuals Search And Download.

Useful Features

To cancel the gain-up function

Gain-up (Cat’s Eye)

Press the GAMA EFF. button until “GAMMA”

When you are recording in a dark or poorly-

illuminated location, “LIGHT” is displayed on

the screen. Use the gain-up function to record

a brighter picture.

disappears.

Notes:

• The Gain-up mode will disengage and the

indicator will disappear automatically if the

VIEWCAM is moved to a bright location.

• Some picture noise appears in Gain-up mode.

The picture noise increases when the

indicator is displayed.

Press the MENU button until

appears (Camera mode).

Press the GAMA EFF. button (A) once.

• “GAMMA” appears, indicating that the

gain-up function is now working.

L I GHT

GAMA

EFF.

PI C

EFF

GAMA QK

EFF REW

L I GHT

GAMMA

PI C

EFF

GAMA QK

EFF REW

To obtain a brighter picture

Press the GAMA EFF. button (A) again.

• The

indicator appears.

GAMA

EFF.

GAMMA

GAMA

PI C

EFF

GAMA QK

REW

EFF

Download from Www.Somanuals.com. All Manuals Search And Download.

Wide Screen (16:9)

Macro Shots

The wide screen function lets you record

scenes with the wide-screen feel of a movie

shown in a theater. The top and bottom of the

picture are masked with black bands to

produce an effective screen aspect ratio of

16:9.

This VIEWCAM lets you shoot close-up images

of small objects such as flowers and insects, or

make title frames for your videos. When you

want to record a magnified image of a subject

which is within approximately 5 feet (1.5 m) of

the VIEWCAM, do not zoom in on it. Instead,

zoom out all the way by pushing the Power

Zoom control to the W side, and then move the

VIEWCAM closer to the subject until you obtain

the desired angle of view. The VIEWCAM will

automatically focus on the subject when the

lens is set for the widest angle.

Press the MENU button until

appears (Camera mode).

SCENE

TLE TURN 16

Press the 16:9 button (B).

• The monitor now displays the

picture with the top and bottom

portions masked.

1FA6D: 9E

Press the DISPLAY button to turn off the

Operation button indicators.

Power Zoom control

Tripod

Normal Screen mode

Wide Screen mode

Notes:

• When you are recording a macro shot, be sure

that the subject receives sufficient illumination.

• It is recommended that you use a tripod for

recording macro shots, to prevent image shakes.

To return to normal picture

Perform step 1 above, and press the 16:9 but-

ton.

Removing the Lens Hood

The lens hood can be removed (e.g. for

cleaning the lens) by rotating it in a

counterclockwise direction (Q) and then gently

pulling it off (W).

Note:

• You can only use the wide screen function when

the VIEWCAM is in Camera mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

Useful Features

Press the Power Zoom

control to obtain the

desired angle of view.

Self Recording

The LCD monitor can be rotated 180° vertically

so that the monitor screen faces the subject.

This lets you record yourself while watching

your image on the screen.

Press the REC START button (B) to

begin recording.

You can enjoy recording a portrait of yourself,

or recording yourself and your friends together

at a party, using the remote control.

MES

REC

START

SAGE

To pause recording, press the REC STOP

button (B).

VR-33FAN

tripod adapter

(optional)

Cautions:

• Do not rotate the monitor to the self recording

position during recording or playback.

• For recording in Self Recording mode, be sure to

rotate the monitor, NOT the lens. If you hold the

VIEWCAM upside down with the lens at the bottom,

the subject will be recorded upside down.

Normal Self Recording

Notes:

• You will need the VR-33FAN tripod adapter for 180°

recording (optional accessory) if you want to use a

tripod when recording in Self Recording mode.

• In Self Recording mode, only the REC START/STOP

button and the Power Zoom control buttons can be

used on the remote control.

Set the Power switch to CAMERA.

Rotate the monitor section 180°

vertically.

• The screen image will be inverted to

show a mirror image of the subject, and

the self-recording mode screen appears.

More Information on Self Recording

• The screen image is automatically inverted when

the monitor rotation is between 135° and 200°.

When the monitor is turned back to the normal

position, the image returns to normal.

• In Self Recording mode, all standard warning

indicators on the screen are replaced by the

flashing

indicator. To check the type of

warning, rotate the monitor back to the normal

position.

• In Self Recording mode, it is not possible to

record using manual recording modes, change

picture adjustments, display menus, record the

date and time, or use the Quick Return and

some of the other functions.

• You can play back images even while the

monitor is in the self recording position. Set the

Power switch to VCR. The Operation buttons still

retain their functions as during normal playback,

even though the button indicators are not

displayed. (For example, the J button still works

as the Play button.)

MES

REC

START

SAGE

Download from Www.Somanuals.com. All Manuals Search And Download.

When the remaining recording time

reaches 5 seconds, “EXTEND” will

begin flashing.

• When you want to extend the recording

time, press the EXTEND button (A)

within 5 seconds. You may record

continuously for 10 more seconds.

Self-recording Message

In Self Recording mode, you can record a short

video message for somebody. This feature is

convenient for editing video letters.

• Complete steps 1 to 3 of “Normal Self

Recording” on page 33, then perform the

procedure below.

MES

REC

STOP

SAGE TEND

EXTEND button

REC START/

MESSAGE button REC STOP button

At the end of the recording, the screen

fades out, and the VIEWCAM returns to

Recording Standby mode.

Note:

• When you want to stop recording before

message recording stops automatically, press

the REC STOP button (B).

Press the MESSAGE button ( ) to

display the self-recording message

screen.

MES

REC

START

SAGE

PRESS REC START FOR

LEAVI NG YOUR MESSAGE.

MES

SAGE

• To cancel, press the MESSAGE button

again.

Press the REC START button (B) to

begin recording. Record your message

while facing the lens of the VIEWCAM.

• The recording time is preset for 20

seconds.

• The bar on the screen indicates the

remaining recording time.

MES

REC

STOP

SAGE

PLEASE START SPEAKI NG.

REC

START

Download from Www.Somanuals.com. All Manuals Search And Download.

Useful Features

If “EXPOSURE” is displayed in yellow,

press the EXPOSURE button ( ) to

display the exposure setting screen,

then press the AUTO button (B).

• The exposure setting screen turns off

and “EXPOSURE” returns to blue.

Setting the VIEWCAM to Full

Auto Mode

This VIEWCAM is equipped with auto focus,

auto white balance, and auto exposure

functions. For easy, high-quality camera-

recording, record subjects in Full Auto mode.

EXPO

EXPOSURE

SURE

If “AUTO” is not displayed even when the

DISPLAY button is pressed, perform the

procedure below to set the VIEWCAM to Full

Auto mode.

AUTO EXI T

In Recording Standby mode, press the

MENU button until appears. If “PIC.

EFF.” is not displayed above the D

button, press this button until “PIC. EFF.”

appears.

AUTO

Blue

B/W

EFF

WHI TE EXPO

BAL.

FOCUS

SURE

Press the MENU button until

appears. If “SCENE MENU” is not

PI C

EFF

GAMA QK

EFF REW

displayed above the A button, press

this button until “SCENE MENU”

appears.

Press the MENU button until

ap-

pears. If “MAN’L FOCUS” is displayed,

press the D button to change it to

“FOCUS”.

SPORT

MAN’ L

FOCUS

SCENE

TLE TURN 16

WHI TE EXPO

BAL.

FOCUS

SURE

Press the DISPLAY button.

• The Operation button indicators

disappear, and “AUTO” is displayed on

the screen.

If “WHITE BAL.” is displayed in yellow,

press the WHITE BAL. button (A).

• “WHITE BAL.” returns to blue.

WH I TE

BAL.

AUTO

Blue

WHI TE EXPO

FOCUS

BAL.

SURE

Full Auto mode indicator

Download from Www.Somanuals.com. All Manuals Search And Download.

Press the REW (C) (or FF [B])

button.

Program Search

• The tape rewinds (or fast forwards) to the

beginning of a scene immediately before

(or after) the current tape position;

playback then starts automatically.

The program search function automatically

finds and plays back the beginning of a

number of previously recorded scenes. Up to

10 different scenes can be found on one tape.

Note:

REW

• This function does not work if no recording has

been made since the cassette was loaded, if the

cassette has been removed after the recordings

were made, or if the power source has been

interrupted.

PROG. SEARCH

REW

ARCH

Press the MENU button until

appears (VCR mode).

To continue searching, press the REW

(or FF) button while “REW” (or “FF”) is

still displayed.

GAMA COU

Notes:

EFF. NTER

ARCH

• Use this function when the tape is stopped or

being played back.

• This function finds the beginning of each scene

immediately before or after the current tape

position. It is not possible to skip a scene.

• This function cannot spot recordings that are

shorter than 10 seconds in length.

Press the SEARCH button ( ).

• “PROG. SEARCH” is displayed and one

of or both “REW” and “FF” will start

flashing.

• In steps 2 and 4, if the tape is at a point ahead of

the last (or before the first) recording, the FF (or

REW) indicator will not appear.

ARCH

PROG. SEARCH

ARCH

REW

• To cancel, press the SEARCH button

again.

Example: When using a tape with five different scenes.

PROG. SEARCH

Monitor display

SE-

ARCH

REW

ARCH

REW

ARCH

REW

Current tape position

Video tape

Beginning of each scene

First recording

Last recording

When you are at this position:

Press the REW button (C) to rewind the tape to E and begin playback.

Press the FF button (B) to forward the tape to R and begin playback.

Download from Www.Somanuals.com. All Manuals Search And Download.

Useful Features

Camera mode

Tape Counter Feature

Press the MENU button until

appears.

The tape counter shows elapsed playback or

recording time in hours, minutes and seconds.

(The counter continues to count internally even

while it is not being displayed.) This feature can

be set and used in both VCR and Camera

modes.

Press the COUNTER button (B) to

display the tape counter.

Press the REC START/STOP button to

begin recording.

• You can check the recording time with

the tape counter.

Using the Counter

VCR mode

Press the MENU button until

appears.

Notes:

• The counter reading may differ slightly from the

actual time. This is especially noticeable when

the tape has been rewound or fast forwarded a

number of times, in which case there can be a

difference of several seconds.

• The tape counter feature will be canceled if the

power source is interrupted.

GAMA COU

SE-

ARCH

EFF. NTER

Press the COUNTER button (D) to

display the tape counter.

To turn off the tape counter

Perform step 1 above, and press the

COUNTER button.

COU

NTER

To reset the counter to zero

Tape counter

During playback (or recording), perform steps

1 and 2 above, then press the RESET button at

the point where you wish to reset the counter to

zero. The counter will indicate 0:00.00.

11 20

NTER ORY SET ARCH

COU

MEM

GAMA

EFF.

Press the MENU button until

appears, then begin playback.

• You can check the playback time with

the tape counter.

VCR mode

SET

00 00

EFF. NTER ORY SET ARCH

GAMA COU

MEM

11 24

REW PLAY FF STOP STI LL

Download from Www.Somanuals.com. All Manuals Search And Download.

Press the REW button (C).

• The tape will automatically stop when the

counter reaches 0:00.00.

Using the Counter Memory

Use the counter memory feature when you

want to return to the beginning of a particular

scene. The position where the counter was

reset (0:00.00) is stored in memory to make it

easier to return to that point on the tape.

11 24

VCR mode

REW PLAY FF STOP STI LL

During playback, press the MENU

button until

appears.

00 00

18 00

REW PLAY FF STOP STI LL

GAMA COU

MEM

RE-

EFF. NTER ORY SET ARCH

Notes:

• The FF button (B) can be used in the

same way.

• The tape may stop slightly ahead or behind

the point where you reset the counter to

“M 0:00.00”.

• If “MEMORY” is not displayed, press the

COUNTER button.

Press the MEMORY button to set the

counter to Counter Memory mode.

• “M” will be displayed to the left of the

counter.

Press the PLAY button (D) to view the

desired scene.

MEM

Camera mode

ORY

Memory indicator

During recording, press the MENU

button until appears.

• If “MEMORY” is not displayed, press the

COUNTER button.

18 31

EFF. NTER ORY SET ARCH

GAMA COU

MEM

Press the RESET button to reset the

counter to zero at the beginning of the

scene that you want to return to later.

Perform steps 2 and 3 above.

When you are ready to finish recording,

press the REC START/STOP button.

SET

Set the Power switch to VCR, then

perform steps 5 and 6 above.

00 00

EFF. NTER ORY SET ARCH

GAMA COU

MEM

To cancel Counter Memory mode

Perform step 1 above, and press the MEMORY

button. “M” will disappear from the screen.

Press the MENU button until

appears. When you are ready to finish

playback, press the STOP button (A).

Note:

• This feature does not work during video search.

Download from Www.Somanuals.com. All Manuals Search And Download.

Useful Features

Operating the Remote Control

Using the Remote Control

Aim the remote control at the remote sensor of

the VIEWCAM, and press the control buttons for

operation.

Use the remote control to operate the VIEW-

CAM from a distance, such as when you want

to record yourself in a scene, or when the

VIEWCAM is connected to a TV for use as a

VCR.

Remote sensor

Installing the Batteries in the Remote

Control

Open the battery compartment cover.

Insert the two supplied AA (R6 or UM/

SUM-3) batteries with the battery poles

positioned as indicated.

Approximate operating

range of remote control

REWind/Reverse Search button

RECord START/STOP button

Power Zoom Telephoto/

Wide angle control

buttons

Replace the cover.

Fast Forward/

Forward Search button

Caution:

PLAY button

STOP button

• Do not use old and new batteries together or

batteries of different brands together.

Turning On the Remote Control Mode

VOLUME buttons

Press the MENU button until

(VCR mode).

appears

PAUSE/STILL button

Press the ĭ or İ button (Q) to select

“REMOTE”, then press the SET button

(B) (W) to select “ON” .

Notes:

• Be careful not to allow direct sunlight or bright

light from interior illumination to fall onto the

VIEWCAM remote sensor, as this may prevent

the remote control from operating properly.

• Be sure that there are no obstacles between the

remote control and the VIEWCAM remote sensor.

• The remote control cannot be used to move the

pointer, or select or set any of the various

functions on the monitor.

EDI T

OFF

REMOTE

SET

PI C

• When the batteries are depleted and the remote

control does not operate, replace them with new

AA (R6 or UM/SUM-3) batteries.

SET TURE

Press the DISPLAY button to turn off the

menu screen.

• You can also turn on the Remote Control mode

on the

(MENU 1) screen in Camera mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

Advanced Features

To cancel the digital picture effect

Digital Picture Effects

Select “PIC. EFF.” in step 2 above.

These digital picture effects let you record the

subject with a more dramatic effect.

Note:

• The digital picture effect will be canceled if the

power source is interrupted.

Type of Digital Picture Effects

B/W EFF.: The picture is recorded in black-

and-white.

SEPA EFF.: The picture is recorded in sepia

color similar to that of an old photograph.

SOLARI: The contrast of the subject is

enhanced, creating a unique artistic image.

NEGA EFF.: The blacks and whites of the

image are reversed and colors of the image

are inverted.

In Recording Standby mode, press the

MENU button until

appears.

PI C

EFF

GAMA QK

EFF REW

Press the D button to select the desired

digital picture effect.

• Each time you press the D button, the

digital picture effect changes as shown

below.

PI C

EFF

PI C

EFF

GAMA QK

EFF

REW

PI C

EFF

SEPA

EFF

B/W

EFF

NEGA

EFF

LARI

Press the DISPLAY button to turn off the

Operation button indicators.

Download from Www.Somanuals.com. All Manuals Search And Download.

Advanced Features

To cancel the scene setting

Scene Menu (Program AE)

Select “SCENE MENU” in step 2 above.

You can set the VIEWCAM to the shooting

mode that will create the best results for a

specific type of shooting situation. Just select

one of the four scene settings shown below.

The VIEWCAM will automatically set the

exposure, white balance, and shutter speed to

produce the optimum picture quality for the

selected situation.

Notes:

• Even after you turn off the scene setting

indicator, the selected scene setting will remain

in effect.

• When “SPORT” is selected, recording under

the light of fluorescent lamps, mercury lamps,

or sodium lamps may cause color shifts or

fluctuations in picture brightness.

• When “DUSK” is selected, the picture may not

be satisfactory if the lighting is very dim.

• It is recommended that you select “SCENE

MENU” to record outdoor parties.

• The scene setting will be canceled if the power

source is interrupted.

Type of Scene Settings

SPORT: When you want to record a fast-

moving subject.

SUNLIGHT: When the background is very

bright.

DUSK: When you want to faithfully record the

red of the setting sun, and the surrounding

twilight.

PARTY: When the illumination is from a

spotlight or candles.

In Recording Standby mode, press the

MENU button until appears.

SCENE

TLE TURN 16

Press theAbutton to select the scene

setting that best fits the recording

situation.

• Each time you press theAbutton, the

scene setting changes as shown below.

SCENE

TLE TURN 16

SCENE

SUN

L I GHT

SPORT

PARTY

DUSK

Download from Www.Somanuals.com. All Manuals Search And Download.

Press the ĭ or İ button (Q) to select

the desired title, then press the SET

button (B) (W) to superimpose it.

Superimposing a Title

Use the title feature to superimpose titles on

your videos when recording. There are eight

titles preset for your convenience which you

can choose from.

TI TLE SUPERSTAR!

HAPPY BI RTHDAY!

HAPPY HOL I DAYS!

SET

WEDDI NG DAY

CONGRATULAT I ONS

NEW BABY

OUR VACAT I ON

THE END

In Recording Standby mode, press the

MENU button until appears.

SET EXI T SET

SCENE

TLE TURN 16

NEW BABY

Press the TITLE button (C) to display

the title selection screen.

SCENE

T I

TLE TURN 16

TI TLE SUPERSTAR!

HAPPY BI RTHDAY!

TLE

HAPPY HOL I DAYS!

WEDDI NG DAY

CONGRATULAT I ONS

NEW BABY

Notes:

• If you wish to cancel the title selection

screen without setting the title, press the

EXIT button (

࡯

) instead of the SET button.

• If you wish to delete the superimposed title

from the screen, press the TITLE button.

OUR VACAT I ON

THE END

SET EXI T SET

Press the REC START/STOP button to

begin recording with the title.

• The title will be displayed and recorded

for about 10 seconds after recording

begins.

NEW BABY

SCENE

TLE TURN 16

Note:

• When the title is displayed on the screen, the

date and time will not be displayed or recorded.

Download from Www.Somanuals.com. All Manuals Search And Download.

Advanced Features

the desired character (or “ ” for

Changing the Preset Titles

space) and press the SELECT button

(

࡯

) (W).

• The selected character will appear at the

top of the screen and the cursor will

automatically move to the right.

You can make a new title of your own by

changing any of the eight preset titles. The

maximum number of title characters is fifteen.

Example: Changing “WEDDING DAY” to “IN

HAWAII”.

Press the MENU button until

appears, and then press the TITLE

button (C) to display the title selection

screen.

T I

LECT SET

TI TLE SUPERSTAR!

HAPPY BI RTHDAY!

TLE

HAPPY HOL I DAYS!

WEDDI NG DAY

CONGRATULAT I ONS

NEW BABY

OUR VACAT I ON

THE END

Note: If you input the wrong character, press

the

button to move the cursor to that

SET EXI T SET

character and perform step 4.

Press the ĭ or İ button to select the

title that you wish to change.

Repeat step 4 until you finish the title,

then press the SET button ( ). The new

title will be displayed on the title

selection screen.

TI TLE SUPERSTAR!

HAPPY BI RTHDAY!

HAPPY HOL I DAYS!

WEDDI NG DAY

CONGRATULAT I ONS

NEW BABY

OUR VACAT I ON

THE END

SET EXI T SET

Note: If you want to cancel the title selection

screen, press the EXIT button (

࡯

Press the RESET button ( ) to display

the title input screen.

Note: To change another title, perform steps

2 to 5 again.

If you wish to record the new title

SET

immediately, press the SET button (B).

If you wish to record the new title at a

later time, press the EXIT button (

࡯

) to

go back to the normal

screen.

LECT SET

Download from Www.Somanuals.com. All Manuals Search And Download.

In Recording Standby mode, press the

MENU button until appears.

Auto/Manual Focus

Auto Focus

The auto focus function is designed to focus on

most types of subjects. In Auto Focus mode,

the VIEWCAM automatically focuses on what-

ever is in the center of the scene. Always keep

the subject in the center of the screen.

WH I T E EXPO

BAL.

SURE

FOCUS

Press the FOCUS button (D) to set the

VIEWCAM to Manual Focus mode

(“MAN’L FOCUS”).

Notes:

• If no subject is in the center of the screen, the

focus area will expand and the subject nearest

the center will be focused on.

FOCUS

• If no subject is displayed on the screen, the

VIEWCAM will automatically zoom out until a

subject comes into the frame.

MAN’ L

FOCUS

WHI TE EXPO

BAL.

SURE

Manual Focus

The Auto Focus may not be able to focus on

the subject in the situations shown below. In

such situations, set the VIEWCAM to Manual

Focus mode and focus manually.

Push the Power Zoom control to frame

the subject as you desire.

Press the F (C) or N (B) button to

focus on the subject.

MAN’ L

FOCUS

WHI TE EXPO

BAL.

SURE

Lack of contrast, e.g. snow

Subject is too dark.

scene.

To cancel Manual Focus mode

Fast-moving subject.

Background is too bright.

Perform step 1 above, and press the D button

to set the VIEWCAM to Auto Focus mode

(“FOCUS”).

Notes:

Subject is being shot through

a dirty or wet window.

Subject has

horizontal stripes.

• The VIEWCAM may not be able to focus

correctly if the subject is within approximately 5

feet (1.5 m). Set the zoom control to wide angle,

and then try refocusing.

• If the lens is dirty or fogged, the VIEWCAM may

not be able to correctly focus.

• The Manual Focus mode will be canceled if the

power source is interrupted.

Two subjects at different distances

overlap in the same scene.

Light reflects off the subject.

Subject has fine, repeated

patterns.

Subjects at different distances

appear in the center of the scene

at the same time.

Download from Www.Somanuals.com. All Manuals Search And Download.

Advanced Features

Press the WHITE BAL. button (A).

• “WHITE BAL.” changes from blue to

yellow and begins flashing.

White Balance Lock

The color of the subject on the screen tends to

look different depending on the lighting

condition. The VIEWCAM is preset to Auto

White Balance mode, which automatically

adjusts the hue of the picture for the current

lighting condition.

WH I TE

BAL.

WHI TE EXPO

BAL.

SURE

FOCUS

The auto white balance may not work properly

for the following subjects. In this case, use the

white balance lock function.

• Subjects with one dominant color or subjects

against background with one dominant color

• Subjects under very bright light source, e.g.

video lights

• Subjects under light source with red hue, e.g.

glow of sunset

• Close-up images of small objects

• “WHITE BAL.” stops flashing when the

locking procedure is completed.

Aim the lens at the desired subject and

press the REC START/STOP button to

begin recording.

To cancel White Balance Lock

Press the WHITE BAL. button. “WHITE BAL.”

returns to blue.

In Recording Standby mode, press the

MENU button until appears.

Notes:

• If the light source changes or if you move from

indoors to outdoors, or vice versa, when

recording with the white balance locked, the

white balance may shift. Reset the white

balance.

WH I T E EXPO

BAL.

SURE

FOCUS

• Even after the white balance has been locked,

white balance shifts may occur due to slight

changes in illumination or depending on the

subject.

Aim the lens at a white object.

• Adjust the distance of the object so that

the entire screen is white.

• Do not move the VIEWCAM while “WHITE BAL.”

is flashing in step 3.

White paper or white cloth

• If “WHITE BAL.” does not stop flashing in step 3,

press the WHITE BAL. button to cancel the

locking procedure and repeat step 3.

• The White Balance Lock will be canceled if the

power source is interrupted.

• The White Balance Lock will be canceled if a

scene setting is selected thereafter.

Download from Www.Somanuals.com. All Manuals Search And Download.

Press the ĭ or İ button to select the

desired exposure level.

Manual Exposure

• The bar indicates the selected exposure

level.

The VIEWCAM is preset to Auto Exposure

mode, which automatically chooses the optimal

aperture. When there is too much contrast in

brightness between the subject and

background, however, you may not be able to

record a clear image. In this case, use the

manual exposure function to correct the

exposure level.

EXPOSURE

AUTO EXI T

Background is too bright and subject too

dark (backlit subject).

• Increase the exposure level to allow more light

through the lens.

EXPOSURE

Less light

More light

Press the EXIT button (A) to turn off

the exposure setting screen.

Subject is too bright against background.

To cancel Manual Exposure mode

• Decrease the exposure level to allow less light

through the lens.

Perform steps 1 and 2 above, then press the

AUTO button (B).

Notes:

• The Manual Exposure mode will be canceled if

the power source is interrupted.

• The Manual Exposure mode will be canceled

if a scene setting is selected thereafter.

In Recording Standby mode, press the

MENU button until appears.

WHI TE EXPO

BAL.

SURE

FOCUS

Press the EXPOSURE button ( ) to

display the exposure setting screen.

EXPO

SURE

EXPOSURE

AUTO EXI T

Download from Www.Somanuals.com. All Manuals Search And Download.

Advanced Features

Press the ĭ or İ button to adjust the

picture or backlight to the desired

setting.

Picture/Backlight

Adjustments

If the monitor picture is difficult to see due to

ambient lighting, etc., adjust the picture

settings. This feature can be adjusted in both

Camera and VCR modes.

• The example screens for this feature are for

Camera mode.

Press the MENU button until

(Camera mode) or

appears.

(VCR mode)

Darker

Decrease

Red

Brighter

Increase

Green

PI C

SET TURE PAGE

Press the PICTURE button (

࡯

) to display

the adjustment screen. Then press the

SELECT button (B) until the item you

wish to adjust appears.

PI C

TURE

BACKL I GHT

AUTO

Type of Backlight Modes

AUTO: The VIEWCAM automatically switches

between “NORMAL” and “BRIGHT”

depending on the ambient lighting. This

mode is only available in Camera mode.

LECT EXI T

NORMAL: For use indoors or under moderate

lighting conditions.

BRIGHT: For use outdoors under strong

lighting conditions, such as bright daylight.

Press the EXIT button (

࡯

) to turn off the

adjustment screen.

Notes:

• If you set the backlight (“BACKLIGHT”) to

“AUTO” in Camera mode and then set the

VIEWCAM to VCR mode, the backlight mode

automatically changes to “NORMAL”.

• When the color or tint is adjusted, the picture on

the screen may differ from the picture actually

recorded. Do not change the color and tint

settings unless it is necessary. (These

adjustments only affect the monitor picture, not

the recorded image.)

Download from Www.Somanuals.com. All Manuals Search And Download.

Gamma Playback

Turning Off the LCD Monitor

Backlight

The gamma playback function improves the

picture by increasing the brightness of the

subject while leaving the brighter portions of

the image unaffected.

The LCD monitor uses a fluorescent lamp for

backlighting (see page 52). In order to reduce

battery consumption, you can turn off the lamp

when backlighting is not necessary (e.g. when

you are recording a fixed scene).

During playback, press the MENU

button until appears.

Hold down the DISPLAY button. Three seconds

later, “LCD LAMP OFF” starts flashing on the

monitor. Keep the DISPLAY button down for

three more seconds, and the backlight will turn

off.

GAMA COU

EFF. NTER

ARCH

Press the GAMA EFF. button (C).

• “GAMMA” appears and the picture

becomes brighter.

GAMA

EFF.

Power switch

DISPLAY button

GAMA COU

EFF. NTER

ARCH

To turn on the backlight again, press the

DISPLAY button or set the Power switch to OFF

and then back to CAMERA or VCR.

Note:

GAMMA

• Turning the backlight on and off repeatedly may

deplete the battery power.

GAMA COU

EFF. NTER

ARCH

To cancel Gamma Playback

Press the GAMA EFF. button again. “GAMMA”

disappears.

Download from Www.Somanuals.com. All Manuals Search And Download.

Advanced Features

Press the Pause/Still button on the VCR to

pause recording when the source tape

reaches the beginning of the sequence to

be cut.

Editing

Video editing lets you refine your videos by

removing unwanted sequences from your tape,

or transposing one sequence with another.

This VIEWCAM lets you monitor the source pro-

gram on the built-in LCD monitor without

having to connect it to an external TV or video

monitor.

Press the Pause/Still or Record button on

the VCR to resume recording when the

source tape reaches the end of the

sequence to be cut.

To stop editing

Connect the VIEWCAM to a VCR with the sup-

plied audio/video cable, as shown.

Press the Stop buttons on the VIEWCAM and

the VCR.

Yellow: To VIDEO IN jack

White: To AUDIO IN (L) jack

Notes:

Recording

• Some of the transitions between edited sequences

may be slightly off.

CHANNEL

AUSE

/STILL

PLAY

• There may be picture noise during video search or

still picture playback. This does not imply a defect in

the VIEWCAM.

STOP/

EJECT

POWER

TV/VCR SET UP

REC

Audio/video cable

(supplied)

Setting Edit Mode

Picture quality inevitably decreases when

dubbing from the VIEWCAM to a VCR. To

minimize the quality reduction, set the

VIEWCAM to Edit mode.

Playback

Set the Power switch to VCR, then press

the MENU button until

appears.

To AUDIO/VIDEO jack

EDI T

REMOTE

OFF

Cutting Unwanted Sequences

PI C

SET TURE

Play back the tape to be edited, and locate

the beginning and end of the sequence

you wish to cut. Write down the tape

counter readings at the beginning and end

of that sequence (see page 37). Then

rewind the tape to the beginning of the

portion that you wish to keep.

Press the ĭ or İ button (Q) to select

“EDIT”, then press the SET button (B)

(W) to select “ON”.

EDI T

REMOTE

SET

Load a video cassette into the recording

VCR.

Set the Power switch on the VIEWCAM to

VCR. Press the PLAY button (D) on the

VIEWCAM and the Record button on the

VCR at the same time.

PI C

SET TURE

Notes:

• The EDIT mode does not function when the

VIEWCAM is recording.

• After you finish editing, set the EDIT menu item back

to “OFF”.

Download from Www.Somanuals.com. All Manuals Search And Download.

References

Lighting

Useful Information

For clear, good-quality recording, 500 to

100,000 lux is needed. Recording is possible

with less light, but the picture quality may

suffer. Adequate lighting is also essential for

correct white balance.

Hints for Better Shooting

• Position the subject in the center of the

screen. When you are using auto focus,

whatever is in the center of the screen is kept

in focus.

Brightness

Situation (Lux)

(Lux)

Blue sky

100,000

Clear day at noon (100,000)

Clear day at 10 am (65,000)

Position the subject in

the center.

Focus manually when

you need to position

the subject off center

(see page 44).

Clear day at 3 pm (35,000)

Cloudy day at noon (32,000)

Cloudy day at 10 am (25,000)

• Avoid backlit subjects. For the best picture,

shoot with the light source behind you.

When the background is brighter than the

subject, the subject often becomes too dark.

If you have to record with this lighting, use the

Gamma Brightness Compensation or correct

the exposure level to improve the picture (see

pages 30 and 46).

10,000

1,000

Cloudy day, one hour after sunrise (2,000)

Clear day, one hour before sunset (1,000)

Fluorescent light near window (1,000)

Factory floor (700–800)

Sales counter in department store (500–700)

Bowling alley (500)

Library (400–500)

Office with fluorescent lighting (400–500)

Fluorescent desk lamp (400)

Flashlight at 3 ft (1 m) (250)

Shop stairway (100)

100

During intermission at movie theater (15–35)

Cigarette lighter at 1 ft (30 cm) (15–20)

Candles on birthday cake at 8 inches (20 cm) (10–15)

Light from behind

Backlighting

• Before zooming, think about how to best

frame the shot. Frequent zooming produces

unattractive pictures. It also increases the

battery power consumption.

• When image shakes are noticeable during

zoomed-in telephoto shooting, use a tripod,

or push the Power Zoom control to the W side

to zoom out.

• Horizontal panning (lateral movement) and

tilting (vertical movement) should be done

slowly to emphasize the wide expanse of a

scene or the height of a building, and to

make scenes easy to watch during playback.

• Use a wide-angle setting for fast-moving

subjects.

Candlelight

Note: The figures in the chart are approximations.

Tips on Good Lighting

In most outdoor, daytime scenes, natural

lighting is adequate for home videos. Indoors,

however, artificial lighting is usually required.

Video lights with halogen lamps provide the

most natural artificial light over a long operating

life.

Note:

• It may take longer to focus when zooming and

panning are used frequently.

Download from Www.Somanuals.com. All Manuals Search And Download.

References

• “Dew” warning feature

Dew Formation

If dew forms, the word “DEW” flashes on the

LCD monitor, and the power will automatically

turn off in approximately 10 seconds.

• What is “dew formation”?

When cold water is poured into a glass, dew

drops form on the glass. This clinging of

water drops is called dew formation.

• When dew forms in your VIEWCAM.

Dew will gradually form on the head drum of

your VIEWCAM and make the video tape stick

to the head. This causes damage both to the

head and the tape. When dew formation

occurs, recording and playback may not

function properly.

Dew is likely to form in the following circum-

stances:

• When moving the VIEWCAM from a cold

place to a warm place.

Q If “DEW” flashes on the LCD monitor,

remove the cassette, leave the cassette

compartment open, and wait for a few hours

to allow the VIEWCAM to acclimate to the

surrounding temperature.

W To use the VIEWCAM again, turn on the

power after waiting for a few hours. Be sure

that “DEW” has disappeared from the

monitor.

E Do not insert a cassette while “DEW” is

flashing; this may result in damage to the

tape.

R Since dew forms gradually, it may take 10 to

15 minutes before the dew warning feature

engages.

• When placing the VIEWCAM in a cold room

which is then heated rapidly.

• When moving the VIEWCAM outdoors from

an air conditioned room.

• When placing the

VIEWCAM in the direct

path of air blowing from

an air conditioner.

• When placing the

VIEWCAM in a humid

room.

Dirty Video Heads

Using the VIEWCAM when the video tape is

dirty may cause the heads to clog, producing

noise on the recorded image or preventing the

image from being recorded at all.

• How to prevent trouble due to dew

formation.

When using the VIEWCAM in a place where

dew formation is likely to occur, allow the

VIEWCAM and the video tape to acclimate to

the surroundings for about one hour.

For example, when bringing the VIEWCAM

indoors after skiing, place it in a plastic bag.

If the video heads become clogged, the

indicator appears on the screen. Contact the

nearest SHARP service center or your dealer

for further advice.

Note:

• Video head cleaning can be done by using a

commercially-available cleaning tape. However,

excessive use of the cleaning tape may also

cause damage to the video heads. Please read

the instructions accompanying the cleaning tape

carefully, before using it.

Plastic bag

Q Be sure to tightly seal the plastic bag

containing the VIEWCAM.

W Remove the bag when the air temperature

inside it reaches the temperature of the

room.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to use the battery pack cover

• When storing a fully charged battery pack,

put the cover on it so that the “CHARGE”

mark printed on the label is seen through the

window, as shown.

Replacing the Fluorescent Lamp

This VIEWCAM uses a fluorescent lamp to

backlight the LCD monitor. If the monitor

becomes dark or difficult to view, the

fluorescent lamp may need to be replaced.

Contact the nearest SHARP service center or

your dealer for further advice.

CHARGE

Window

Cover

Battery

pack

Battery Pack

Label

Battery pack consumption

• Recording with many starts and stops,

frequent zooming, and recording in low

temperatures will shorten actual recording

times. Accordingly, be sure to turn off the

power when not recording. Use of an auxiliary

battery pack is recommended to prevent

undesirable interruptions in your recording.

• Do not use an insufficiently charged or weak

battery pack. Use of such battery packs may

cause the power to automatically stop during

VIEWCAM operation to protect both the

battery pack and the unit.

• When storing a battery pack that is not fully

charged, put the cover upside down so that

only the battery pack casing is seen through

the window.

Caution:

• For safety reasons, put the cover on the

battery pack when it is not being used. If the

metal parts of the battery pack come in

contact with other metal items, there is a

danger that a short circuit may occur.

Note:

• This VIEWCAM uses a Ni-MH (nickel-metal

hydride) type battery pack. Use only the

SHARP BT-H22 or BT-H32 battery packs.

They are designed specifically for use with

this VIEWCAM.

Battery power is consumed even when the

VIEWCAM’s power is turned off. If you are not

going to use your VIEWCAM immediately,

remove the battery pack (see page 7).

Temperature during charging

Battery pack life

• The Ni-MH (nickel-metal hydride) type BT-H22

and BT-H32 battery packs can be charged at

a temperature of 15°C to 30°C (59°F to 86°F).

The battery pack has a limited service life. If

the period of use becomes noticeably

shorter with a normal charge, the battery

pack is at the end of its service life. Replace

it with a new battery pack.

Extending battery pack life

• It is recommended that you use the battery

pack until its charge is fully drained and the

VIEWCAM is inoperable before recharging

the pack.

• Recharge the battery pack right before

recording. A battery pack stored for an

extended time will naturally wear down,

resulting in decreased recording time.

• Do not try to recharge a fully charged battery

pack before it has been discharged, as this

will cause deterioration of the battery’s

capacity.

• Store the battery pack in a dry, cool place.

Download from Www.Somanuals.com. All Manuals Search And Download.

References

Video Cassette Tapes

UsingYour VIEWCAM Abroad

Use only tapes with the

VIEWCAM.

mark with this

Television signal standards and electrical

voltages and frequencies vary substantially

from country to country. When you are abroad,

check the sections below before using the AC

adapter or connecting the VIEWCAM to a TV.

To protect recordings against erasure

When a previously recorded cassette is used

again for recording, the previously recorded

material is erased. To protect a recording

against accidental erasure, slide the tab on the

cassette to cover the opening. (A red mark will

be exposed.) To record, slide the tab to open

the opening.

AC Adapter (Supplied Accessory)

The supplied AC adapter is compatible with

50 Hz and 60 Hz electrical systems in the

range of 110 V to 240 V AC.

An AC plug adapter may be required

depending on the design of the electrical

outlet.

Notes:

AC 110–240 V

• Do not insert anything into the erasure-protection

opening in the cassette.

Suitable AC plug adapter

• Do not put anything into the holes on the bottom

of the cassette.

• Do not store or place your video tapes in direct

sunlight, near heaters, or in places with

excessive moisture or dust.

• Do not keep video tapes near magnetic objects

as they may erase the recording.

• Do not drop or subject the tapes to excessive

shocks.

Television Signal Standards

In any country, you can always watch the video

picture by using the LCD monitor screen.

However, if you want to watch the picture on a

TV screen, the TV must be NTSC-M system

compatible. NTSC-M is used in the following

areas:

The Bahamas, Barbados, Bermuda, Myanmar

(previously Burma), Canada, Chile, Colombia,

Costa Rica, Cuba, the Dominican Republic,

Ecuador, El Salvador, Greenland, Guam,

Guatemala, Haiti, Honduras, Jamaica, Japan,

South Korea, Mexico, the Netherland Antilles,

Nicaragua, Panama, Peru, the Philippines,

Puerto Rico, St. Kitts, St. Lucia, Surinam,

Taiwan, Trinidad, the U.S.A., Venezuela,

Southern Vietnam, and the Virgin Islands.

• Uneven tape winding will damage the tape. If the

tape is not properly wound, reinsert it in the

VIEWCAM and rewind the tape.

• Store the cassettes in their cases and stand

them upright.

Download from Www.Somanuals.com. All Manuals Search And Download.

Canceling Demo Mode

Demonstration Mode

During the demonstration, perform step

3 above.

You can watch a brief demonstration of the

special VIEWCAM features in Demo mode.

If the demonstration appears on the screen

when you turn on the VIEWCAM for the first

time, cancel the Demo mode to use your

VIEWCAM.

Press ĭ or İ button (Q) to select

“DEMO MODE”, then press the SET

button (B) (W) to select “OFF”.

Power switch

SET

FADE

NORMAL

OFF

REMOTE

DEMO MODE

LANGUAGE

Press the DISPLAY button to turn off the

menu screen.

MENU button

Operation buttons

Note:

• The demonstration will stop if you press the

MENU button. If you leave it for 60 seconds, or

turn the power off temporarily and then set the

Power switch to CAMERA, the demonstration will

begin again.

Watching the Demonstration

Make sure that there is no video

cassette in the VIEWCAM.

• If a cassette is in the VIEWCAM, Demo

mode does not work. Perform the

procedure on page 10 to remove it.

Lock button

Hold down the Lock

button and slide the

Power switch to

CAMERA.

Press the MENU button until

appears.

• If MENU 2 appears on the

press the PAGE button ( ) to display

MENU 1.

screen,

Press ĭ or İ (C or D) button (Q) to

select “DEMO MODE”, then press the

SET button (B) (W) to select “ON”.

• The demonstration begins.

SET

FADE

NORMAL

REMOTE

DEMO MODE

LANGUAGE

Download from Www.Somanuals.com. All Manuals Search And Download.

References

Before Requesting Service

Before calling for service, please check the following troubleshooting table.

Symptom

No power.

Possible cause