SV Sound
OWNERS’
GUIDE
SVS PB13-Ultra and
PC13-Ultra Subwoofers
Contents:
Chapter 2 Safety instructions
Chapter 3 SVS Welcome
Chapter 4 About your SVS subwoofer
Chapter 5 General subwoofer features
Chapter 6 Setup, integration, and calibration
Chapter 7 Variable tuning feature
Chapter 8 Parametric equalizer (PEQ)
Chapter 9 Room compensation control
Chapter 10 Subwoofer specifications
Chapter 11 Terms and Conditions
Last update: 27 April, 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2-2
SV Sound
13. Unplug this apparatus during lightning storms or when unused for
long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is re-
quired when the apparatus has been damaged in any way, such as
power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been ex-
posed to rain or moisture, does not operate normally, or has been
dropped.
15. WARNING: To reduce the risk of fire or electric shock, this appara-
tus should not be exposed to rain or moisture and objects filled with
liquids, such as vases, should not be placed on this apparatus.
16. To completely disconnect this equipment from the mains, discon-
nect the power supply cord plug from the receptacle.
17. The mains plug of the power supply cord shall remain readily oper-
able.
The lightning flash with arrowhead symbol within an
equilateral triangle, is intended to alert the user to the
presence of un-insulated "dangerous voltage " within
the product's enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the product.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
SVSound
Welcome!
At SVS, you can actually hear the
tireless research and design efforts
built in to our subwoofers and speak-
ers. Years are spent developing any
SVS product — with work typically
spanning from our Ohio headquar-
ters… to US west coast technology
centers… and over to the finest component suppliers in Asia and
Europe as well. Nothing in our speaker offerings is an ―off the shelf‖
product. SVS is committed to making better sound systems with ele-
gant looks, robust construction and world-class technology and materi-
als. We believe you deserve nothing less.
This manual and the printed ―Quick Start‖ sheet will help you integrate
speakers and subwoofer quickly and with professional results.
Armed with only a few basic tools, such a sound pressure level (SPL)
meter, and the test tones built in to most audio/video receivers (AVR),
you will achieve smooth, detailed and powerful reproduction of all your
favorite music and movie audio. Expect to hear things you never
heard before… and expect not to hear some of the artifacts you might
have accepted in the past with inferior brands.
Have a question about your surround sound system? For more
information about SVS products check out our US website, or the ex-
clusive dealer for your region, contact us via phone or e-mail should
you have questions regarding our products.
SVS was founded by audio enthusiasts — our commitment to service
is the only thing that rivals the products we create. Our resellers
around the world feel the same way.
The SVS Team, Ohio, USA
September, 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
SV Sound
About your SVS Subwoofer
There maybe be other subwoofers that look like them, but
virtually none work like them. SVS subwoofers are decidedly
different in how they are designed, produced, sold, and the
exceptionally high quality components we use. You could have
spent much more on other brands and still not come close to the
performance our products provide. What makes a subwoofer an
SVS?
Quality components, sane prices. You might be surprised at how
inexpensive the components in some not-so-inexpensive
subwoofers are. At SVS, performance is king... not cutting a few
dollars from our ―cost to build‖.
Innovative designs, rich materials. We test all our materials, and
features in the real world, and test size and shape, before any
design is deemed ready. Cabinet construction must ensure rigid
and durable products. All our subwoofers offer computer controlled
panel cutting, steel fasteners, and recessed components. Tap the
side of your sub, look at the solid construction or remove your grill,
and you’ll know what we mean.
Sealed, or vented, down-firing or front-firing cabinets. An SVS
tradition is to offer a variety of ―form factors‖ which provide
exceptional performance yet also a compact ―foot print‖ which
complements your room style.
Features and controls. Variable phase, crossovers which can be
defeated, and on select models, variable tuning, equalizers or other
advanced controls are built in to allow customers to make their SVS
fit their needs. Spend time exploring this guide and contact your
dealer if you require assistance on any feature.
World class power. Our advanced amplifiers are designed and
manufactured with a level of fit and finish, and genuine power which
is rare at our competitive prices. Loaded with comprehensive of
easy to use controls, and our tremendously efficient Ohio-built
woofers, all our subs achieve exceptional depth, tremendous power
and flat, natural sound. Hear everything on your music CD’s and
DVD’s with SVS products..
Download from Www.Somanuals.com. All Manuals Search And Download.
SV Sound
Chapter 5-1
Powered Box Basic Common Features.
SVS subwoofer amps use the most durable and accurate designs
possible. Get familiar with yours!
Volume/Gain Use ―gain‖ (in conjunction with your Audio Video
Receiver (AVR) subwoofer output level control) to achieve bass
level calibration to your liking. Start your setup with the sub’s vol-
ume/gain no more than 1/4 to 1/3 of the way up (turned clockwise
from the left).
Crossover Frequency. If you use your AVR’s internal crossover
to manage bass frequencies (highly recommended), the setting of
this knob on your SVS sub is irrelevant. (Note: Use the sub’s
crossover ―Enable/Disable‖ switch discussed below to take advan-
tage of this configuration.)
Phase. Think of long bass waves as conflicting or enhancing
each other, depending on the timing of their arrival at your listen-
ing location (either together, or not). Set phase to zero if your
AVR offers settings for the distance from your seat to your sub-
woofer. Adjust in small steps for smooth sound with music playing
if your AVR lacks a subwoofer distance setting.
Line In/Out. Use either of the sub’s ―Line In‖ jacks (RCA or XLR
type) to connect the subwoofer to the output jack of your AVR.
Feeding just one input is enough. If you are using a conventional
amp and/or a stereo setup you can use the ―Line Out‖ jacks to
send sound (filtered of deep bass information) back to your sys-
tem amp, or switch off this filter. A simple RCA or XLR signal
cable is all you need for either type configuration. See ―Crossover
Feature‖ discussion below for more on Line Out options.
Auto-On. Your Powered Box allows itself to be in an ―Auto-On‖
mode… or ―On‖ all the time. With the former setting (the switch in
the ―Auto‖ position) your subwoofer will ―sense‖ that a DVD or CD
etc. has begun and switch its audio circuits on immediately (the
―hard‖ power switch mentioned below must be set to ―on‖, natu-
rally). A few minutes after a movie, the Auto-On light will turn from
Green to Red, switching portions of the sub’s power supply back
off.
Download from Www.Somanuals.com. All Manuals Search And Download.
SV Sound
Chapter 5.2
Sometimes, with very low listening levels, your subwoofer might
not get enough of a bass signal from your AVR to ―trip‖ the Auto-
On circuit. Should you ever find this to be the case you may leave
this switch to ―On‖, or turn up the AVR’s subwoofer level some (be
sure to recalibrate channels levels with your sound meter after-
wards).
Crossover Feature Switches. If you allow your DD/DTS sur-
round-sound receiver or processor to manage bass frequencies
(again, highly recommended), this switch should be set to
―Disabled‖, eliminating the effects of the ―Crossover Frequency‖
knob and allowing your sub to reproduce just what is fed from the
receiver. If you use the sub in a two channel (stereo only) con-
figuration, then ―Enable‖ the crossover and adjust the knob to best
blend the sub into the output of your speakers.
XLR and RCA Hi-Pass filters can be switched ―Off‖ if
you desire to ―daisy chain‖ the output of one sub to the input of
another without frequency response conflicts; or pass full-range
audio signals to an outboard stereo amp/receiver.
Power. This heavy-duty two-position switch next to the power
cord will completely cut the power to your sub amp. Flip this
switch to off before you ever move the sub or change inputs or
outputs. Do not plug this sub into receiver convenience power
outlets. Allow five minutes of ―off‖ time before switching back
―on‖.
Fuse. User replaceable, contact your dealer if you have trouble
finding one. The fuse can be accessed by a small door immedi-
ately next to the power cord fitting
(where you should also find a spare one for your use).
Read ahead for advanced features including Room Compen-
sation, Variable Tuning and Parametric Equalization (PEQ).
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6-1
SV Sound
Setup, calibrating and integration
What’s to know? Setup is easy! However, there are key steps
which must be done carefully and correctly, read on:
Unpacking. Take a few moments to carefully unpack everything. Save
the box and shipping materials, just in case you need to return the sub
for any reason.
Location. Where you put a sub is important to how it will sound. Use a
corner if you can, and avoid putting your sub where it might adjoin large
open areas. Studies have shown that the deepest and flattest bass
response is typically attained when a subwoofer is placed within a few
feet of one of your room’s corners (leave about 3‖ in the back for cable
clearance with any wall or other surface). Whether you put the sub in
front or to the rear of your room makes surprisingly little difference.
Hook-up (see Fig. 1). There are a variety of ways to configure your new
sub. Usually, a simple mono, shielded 75 Ohm A/V RCA type cable (a.)
is used to take the subwoofer output of your AVR (b.) and feed one low-
level input of the sub’s amp. There is no need to ―split‖ the signal going
to the sub (c.). You can feed either one of the two amp inputs, it
doesn’t matter, right or left.
NOTE: Take time to review
your AVR manual. Ensure all
power to your equipment is off
when making these connec-
tions. Also, be certain your power outlet
can handle a minimum of 1000 watts.
(Use of ―convenience outlets‖ on receivers
are not recommended for your sub).
(a.)
(b.)
DD/DTS Processor/
Receiver
(c.)
Fig. 1
Download from Www.Somanuals.com. All Manuals Search And Download.
SV Sound
Chapter 6-2
More Setup, calibrating and integration
If you are running a pair of SVS subwoofers (Fig. 2), you will need to use an
inexpensive ―Y‖ cable adapter (d.) From the ―Y‖ cable you can run a stan-
dard 75 Ohm RCA or XLR signal cable (e.) to each sub, thus ―splitting‖ the
Low Frequency Effects (LFE) and other bass from your receiver, and effec-
tively feeding both subwoofers with the same signal.
NOTES: Determine if you want
―ON‖ (always on) or ―AUTO ON‖
which turns your sub on only
when a bass signal is present.
High power amp designs can
require five minutes of ―OFF‖ time before sub
will resume ―ON‖ status again.
―Y‖ cable/splitter from AVR
(e.)
AVR (Subwoofer ―Out‖) jack
(d.)
Fig. 2
―Calibration‖ isn’t only for technically minded sound enthusiasts. It is ’s criti-
cal to a proper configuration of your home audio system. Fortunately, adjust-
ing channel balance (essentially all ―calibration‖ amounts to) is simple to do.
The first requirement is to ensure your AVR is ready. Thus we recommend
you consult your AVR manual to review the choices you have regarding
setup. Generally, this requires your receiver’s test tones play back at the
same volume from each of your system’s speakers. Of course this can in-
clude speakers at left, center, right, left surround and right surround plus the
subwoofer itself.
Some things to check as you get ready to calibrate:
Are your speakers set correct to the correct “size”? Your
AVR should allow you to your speakers be set to ―Small‖ or
―Large‖. Selecting the size accordingly will ensure bass goes to
most appropriate speakers, and use the subwoofer correctly too.
―Small‖ is nearly always the best configuration with a good sub-
woofer.
Download from Www.Somanuals.com. All Manuals Search And Download.
SV Sound
Chapter 6-3
Also, is your subwoofer turned ―ON‖? We don’t mean ―is your sub-
woofer amplifier on?‖ but rather, is your AVR sending a bass sig-
nal to your sub amp? This can only happen if you say ―Yes‖ (or
―ON‖) in the ―Subwoofer‖ selection during the setup of your AVR’s
setup menu.
Is your receiver connected to the sub amp? Use a well-shielded
―RCA‖ or XLR cable (sometimes called a ―patch cord‖) to connect the sub-
woofer output of your AVR to either input jack of your subwoofer’s dedicated
amp. Again, you’ll need to ―split‖ the bass signal with a ―Y Cable‖ if you
have a pair of subs. But you only need feed one of the two inputs (it doesn’t
matter either Right or Left) of any SVS Powered Box sub.
Is your Radio Shack ® sound pressure level (SPL)
meter ready? This tool is absolutely essential to proper
home audio setup. It’s akin to a tire pressure gauge for
your car. Set the meter to ―Slow‖ and ―C-weighting‖ (and
turn the dial to 70dB. If using Avia for calibration tones, set
your meter to 80dB instead.
Getting ready to start now: Make sure your receiver or proc-
essor’s master volume is set to ―00 dB‖ or some other easy to
remember “reference level”. Then, ensure your sub’s volume/
gain control is set no more than 1/4 to 1/3rd up, for now, leaving plenty of adjust-
ment ―up‖.
It’s also critical to check the subwoofer output level control of your AVR before
you begin the test tones. Set the AVR’s subwoofer output to about 1/3rd up too.
Turn off any sound-field processing schemes, ―Mid-night Mode‖, ―DRC‖ (dynamic
range control), ―Movie Mode‖ etc. If it is an option in your system, route your
LFE to the ―subwoofer only‖, not ―mains + sub‖.
Now play your AVR’s internal test noise “tones” so you have something to
measure with your SPL meter. When the tones start alternating from speaker
to speaker (watch your sound meter now), set each speaker’s volume to about
75 dB by using the receiver’s dedicated channel level controls (leaving your
AVR’s master volume the same).
We recommend you turn down the AVR’s subwoofer channel output level before
you significantly lower your subwoofer’s gain control. This helps keep distortion
sent to your SVS to a minimum. Note: You should not set the AVR’s subwoofer
level control much lower than the first 1/4th of the receiver’s control range.
Some downward adjustment may be needed to fine tune levels later. If your
subwoofer’s SPL meter reading is still too high, then turn down the sub’s amp
volume a little with each run of the test noise signal, as it cycles from speaker to
speaker and the subwoofer.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6-4
SV Sound
But what’s “too high”?? Tastes vary, and do movie soundtracks,
but your SVS subwoofer is capable of tremendous levels of low distor-
tion, low frequency bass — far more than most subs in this size or
price class. Take advantage of this, especially if you like action mov-
ies with lots of ―.1‖ channel (LFE) bass action, and give the sub a bit
extra gain during calibration. Keep in mind too that the human ear is
relatively insensitive to low frequencies. This, coupled with the fact
most folks don’t watch movies at full ―theater levels‖ means raising the
bass up a few decibels (dBs) usually yields a more satisfying movie
and music experience.
What bass levels do we recommend? If you watch movies at mod-
erate sound levels, a good start is a range of +1dB to +3dB above your
other channels (as measured with your sound meter). This means the
test tone will waiver about 78 dB for the subwoofer portion of the cali-
bration run using your receiver test tones.
Note too that many modern A/V receivers allow a variety of subwoofer
level settings, depending on the ―listening mode‖ you are in. With
―Dolby Digital‖ as your ―mode‖ use the above calibration routine. You
may well find that CD ―Stereo‖ music calls for a lower bass settings.
The above is a guide… experiment! The louder your master AVR vol-
ume however, the more you should reduce the subwoofer’s playback
level to compensate. You should always avoid your driver ―bottoming‖,
resulting in a loud ―clack‖!
Location and measurement. You should take the above measure-
ments from your typical preferred seat for watching movies. Be ad-
vised, strong bass levels can vary tremendously simply by moving
your seat, or your subwoofer, just a short distance. Such is the nature
of long wavelength, deep bass sound. Do not hesitate to try different
locations and different levels for your subwoofer.
Setting playback levels on the sub which are too high (and often, too
low) is the most common theater/music setup error.
Download from Www.Somanuals.com. All Manuals Search And Download.
SV Sound
Chapter 7-1
Advanced Features:
Subsonic Filter and Port Tuning
Your new SVS subwoofer comes with cus-
tom foam port plugs and variable sub-
sonic filter which allows your sub to be
―tuned‖ to even lower frequencies than its
stock configuration. For most people and
most rooms, your sub is already configured
for the best blend of extension (how deep/low your sub goes) and output
(how loud it gets). However, we know bass is a very personal taste and
no two rooms will react exactly the same with any subwoofer.
There are some compromises when tuning a sub lower than its standard
configuration. Installing one port plug takes some capacity from upper
reaches of bass, installing two port blocks limits upper bass ―headroom‖
even more. So while deeper settings will indeed provide more bass down
low (where DVD and music bass is more rare, but quite exciting!), you’ll
sacrifice some total output capacity above the stock tuning point of the
sub (where bass is more common). You should decide if the effect is
pleasing on the sorts of movies and music you enjoy.
How to do it? Remove your grill by prying up with our fingers along its
metal side. To insert a port plug, simply squeeze the foam on one end
and press the plug into a port flare until it is about 1‖ lower than the edge
of the surface of the sub. You can remove the plug by inserting your fin-
gertips into the port flare and squeezing and pulling on the foam plug at
the same time.
SVS Tuning Chart
Subsonic Filter Knob
Stock tune (no ports blocked)
With one port-blocked
20Hz
15Hz
With two ports-blocked *
With three ports-blocked
10Hz
Sealed
Be sure to select the subsonic filter point on the back of your SVS amp
which coincides correctly with your new ―tuning point‖. NOTE: We
strongly recommend you do NOT run a lower subsonic filter point than
your port plug configuration would dictate — especially if you are running
the subwoofer at high sound pressure levels.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
SV Sound
Chapter 8-1
Advanced Features: Parametric Equalizer (PEQ).
Important Note: Until you are ready to use the PEQ feature set, it should be
disabled by setting all three controls to the full counter clock-wise position.
Background Information: Direct and reflected bass waves in the listening
room will create ―standing waves‖ and associated peaks and nulls in the sub-
woofer frequency response (FR). The PEQ allows you to reduce the severity
of a peak in the subwoofer frequency response, thus obtaining a more accu-
rate sound.
Control Explanation: The PEQ has three controls: Frequency, Bandwidth,
and Level. An image of the PEQ control is provided below (your subwoofer
controls may vary).
The Frequency control (labeled ―Freq.‖) affects the target the frequency
where the PEQ cut will take effect, and has a control range of 20-80 Hz.
The Bandwidth control (labeled ―Q‖) affects the width of the PEQ cut. The
―HI‖ setting is the narrowest bandwidth, and the ―LO‖ setting is the widest
bandwidth. In most cases, it is best to start with a Hi Q setting (narrow band-
width).
Below is a frequency response graph of the SVS SB12-Plus as measured
under quasi-anechoic conditions. This set of curves illustrates how the PEQ
function works and what type of cut effect you can expect from various Q
settings.
Green Line: Native frequency response of the subwoofer.
Purple Line: Frequency = 50 Hz, Q = HI, LEVEL = MAX.
Yellow Line: Frequency = 50 Hz, Q = LOW, LEVEL = MAX.
Download from Www.Somanuals.com. All Manuals Search And Download.
SV Sound
Chapter 8-2
“Q” Control Effects
Measuring The In-Room Frequency Response: In order to use the PEQ
effectively, you must measure the in-room FR of the subwoofer at the lis-
tening positions. This can be done manually using test tones and an
spreadsheet, or it can be accomplished using software such as ―TrueRTA‖,
or ―Room EQ Wizard‖. SVS does not provide technical support on the set-
up and use of any software, but it can make measuring the subwoofer FR
easier and faster than manual methods.
To measure the subwoofer FR using a manual method, you will need an
SPL meter, a basic working knowledge of Microsoft Excel (or other spread-
sheet program), and a means to generate sine wave test tones. There
are several sources of sine waves and/or tone generators on the internet.
A popular tone generator is the NCH Tone Generator (http://
www.nch.com.au/tonegen/index.html) which is freeware for personal
use, but may also be purchased for a nominal fee.
Place the SPL meter on a tripod and set the controls to C-weighted, Slow,
and the 70 dB scale (you may need to alter the dB scale during the meas-
urement process). Place the meter at head level at the primary listening
position with the meter pointed toward the front stage and pointed toward
the ceiling at a 45 degree angle.
Download from Www.Somanuals.com. All Manuals Search And Download.
SV Sound
Chapter 8-3
To set the overall test level, play a 25 Hz frequency and adjust the sub-
woofer gain (option 1 below) or the processor master volume (option 2
below) until the SPL meter reads about 75 dB at the listening position.
Run each tone only long enough to get a stable reading from the meter
(about 5-6 seconds), and then give the subwoofer about 10 seconds to
cool off between test frequencies.
Option 1: Measure The FR of the Subwoofer Only:
To measure the FR of the subwoofer only, connect your sound card out-
put directly to a line level input on the subwoofer. Use the Excel spread-
sheet named Subwoofer Frequency Response, which will plot the fre-
quency response of the subwoofer from 11.2 Hz to 100.8 Hz. Input your
raw (direct read) values from your SPL meter into the green band of fre-
quencies in the Raw SPL Data worksheet, and the Frequency Response
worksheet will plot the FR of the subwoofer.
Below is an example of a subwoofer FR. Notice the large peak from 35-
55 Hz.
To correct a peak such as that above, start by setting the Frequency to
about 40 Hz, the Q to HI, and the Level to MAX. Re-measure and re-plot
from 30-70 Hz to evaluate the effect.
Download from Www.Somanuals.com. All Manuals Search And Download.
SV Sound
Chapter 8-4
Option 2: Measure the Combined FR of the Speakers and Subwoofer:
To measure the combined FR of the front speakers and subwoofer (to in-
clude the digital crossover in your processor), connect your sound card
output to an analog input on your processor. Make sure the analog input is
configured to use the digital crossover between the speakers and the sub-
woofer. Use the Excel spreadsheet named Speaker And Subwoofer Com-
bined Frequency Response, which will plot the frequency response from
11.2 Hz to 201.6 Hz. Input your raw (direct read) values from your SPL
meter into the green band of frequencies in the Raw SPL Data worksheet,
and the Frequency Response worksheet will plot the combined FR of the
speakers and subwoofer.
Adjusting The PEQ: Identify the largest/widest peak in the response and
target it for reduction with the PEQ control. When making adjustments to
the PEQ control, there is no need to re-plot the entire FR for interim adjust-
ments simply re-plot the affected section of the curve to verify your PEQ
adjustments are having the desired effect. When you are done making
adjustments, you can re-plot the entire frequency response to obtain a final
curve.
Download from Www.Somanuals.com. All Manuals Search And Download.
SV Sound
Chapter 8-5
Set the Frequency control to the approximate center frequency of the
largest peak. Set the Q control to HI (narrowest bandwidth), and set the
Level control to MAX. Play the test tones again and re-measure and re-
plot the affected portion of the FR curve and visually evaluate your re-
sults. Simple trial/error will then allow you to adjust all three controls to
shape the PEQ cut to achieve the desired effect.
The previous image shows the results of the first PEQ cut attempt. The
Frequency and Cut effect look correct, but the Q is too narrow. Adjust
the Q about 25% wider and try again.
The graph above illustrates the results of the wider Q setting. Notice how
the cut effect is wider. This is now a satisfactory result.
Download from Www.Somanuals.com. All Manuals Search And Download.
SV Sound
Chapter 9
Advanced Features: Room Compensation
In typical home theaters a phenomenon known as ―room gain” can play a
major role in how accurately bass is produced.
When any subwoofer produces notable bass energy below 27Hz, the output
you will perceive is different than the sub’s normal output would be (if unaf-
fected by your room’s walls).
The difference in theoretical bass, versus actual bass response, is depicted in
the graph below. The red trace indicates a subwoofer response outdoors, but
line in blue indicates the same subwoofer’s response in a mid-sized room.
―Room gain‖ can create excessive deep bass which can sound exaggerated
simply due to interaction with your room .
SPL vs Freq
dBSPL
115
110
105
100
95
90
85
80
75
70
65
60
55
10 Hz
20
30
40
50
60
70
80
90
100
6: Anechoic
7: 2800ft^3
Enclosure
Shop
Person: Jim Farina
Company: SV Sound, LLC
Project: Room Compensation
File: Room Compensation.led
Jul 18, 2006
Tue 4:42 pm
5.2.0.350 Jul/15/2005
Use the below chart to help tailor your SVS sub to your room’s size. Vary the
room size knob up or down one size should you determine that sound’s best
for your music and movies. Bypass mode is deepest of all and most suitable
for the largest rooms.
Approximate Room Size
Room Compensation Setting
LARGE
> 2400ft3 (68m3)
1400ft3 – 2400ft3 (40m3 – 68m3)
MEDIUM
SMALL
< 1400ft3 (40m3)
Download from Www.Somanuals.com. All Manuals Search And Download.
SV Sound
Chapter 10
Specifications
Model Name:
Configuration:
Design:
PB13-Ultra
Powered Box, front-firing 13‖ woofer
Vented, Variable Tune with Sealed Mode
22‖ High x 20.5‖ Wide x 27‖ Deep
Dimensions:
H x W x D
56 cm H. x 52 cm W. x 68.6 cm D.
155lbs (70.5kg)
Weight:
110~120V/60hz (US/Canada/South America)
220~240V/50hz (Europe, Russia, other)
Voltage (fixed):
Driver:
13‖ SVS designed/built ―Ultra‖ woofer with high
-excursion synthetic surround, foam/glass
cone with cast basket, high-temp US voice coil
and integral cooling vents
Frequency Response: 18Hz - 150Hz ± 3dB (typical in-room response
(quasi-anechoic)
3-5Hz deeper) with 20hz tuning
RCA and XLR (low level)
Inputs/Outputs:
Gain, continuously variable phase, crossover
(defeatable), auto on, PEQ, Room Compensa-
tion, variable tuning and high-pass filter
switches
Controls:
750 watt RMS
Power Handling:
High pass: 12dB/octave @ 80Hz
Variable low pass: 12dB/octave (40-120Hz)
Crossover:
1‖ Medium Density Fiber-board (MDF) with
internal CNC’d bracing, and wood, gloss or
textured black epoxy finishes
Enclosure Material:
Download from Www.Somanuals.com. All Manuals Search And Download.
SV Sound
Chapter 10
Specifications
Model Name:
Configuration:
Design:
PC13-Ultra
Powered Cylinder, front-firing 13‖ woofer
Vented, Variable Tune with Sealed Mode
47‖ High x 16‖ Diameter
Dimensions:
H x Diam.
119 cm H. x 41 cm Diam.
155lbs (70.5kg)
Weight:
110~120V/60hz (US/Canada/South America)
220~240V/50hz (Europe, Russia, other)
Voltage (fixed):
Driver:
13‖ SVS designed/built ―Ultra‖ woofer with high
-excursion synthetic surround, foam/glass
cone with cast basket, high-temp US voice coil
and integral cooling vents
Frequency Response: 18Hz - 150Hz ± 3dB (typical in-room response
(quasi-anechoic)
3-5Hz deeper) with 20hz tuning
RCA and XLR (low level)
Inputs/Outputs:
Gain, continuously variable phase, crossover
(defeatable), auto on, PEQ, Room Compensa-
tion, variable tuning and high-pass filter
switches
Controls:
750 watt RMS
Power Handling:
High pass: 12dB/octave @ 80Hz
Variable low pass: 12dB/octave (40-120Hz)
Crossover:
1‖ Medium Density Fiber-board (MDF) with
internal CNC’d bracing, and wood, gloss or
textured black epoxy finishes
Enclosure Material:
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11
SV Sound
Terms and Conditions
Terms and Conditions: Details are available on request, please contact
your Dealer for more. Note that these terms and conditions do not affect
your statutory rights.
Shipping: When you receive your new subwoofer, please check to en-
sure there is no damage. If after unpacking you discover any damage that
may have been caused by transportation on your product, we request you
contact SVS or if outside the USA your Dealer immediately and if possi-
ble, provide a photo of damage in question to them to ensure the fastest
possible correction to the situation.
Warranty: The product has a 3 year warranty against defects in materials
and workmanship. Upon return, the products will be repaired, and redeliv-
ered. Naturally, this warranty does not cover any product subjected to
misuse or accidental damage.
The bottom line: We’re proud of these subwoofers and want you to be
as happy owning one, as we are selling one (or more) to you. E-mail your
Download from Www.Somanuals.com. All Manuals Search And Download.
|