®
SUPER
X7DCL-3
X7DCL-i
USER’S MANUAL
Revision 1.0c
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Preface
About This Manual
This manual is written for system integrators, PC technicians and
knowledgeable PC users. It provides information for the installation and use of
the
X7DCL-3/X7DCL-i motherboard. The
X7DCL-3/X7DCL-i
supports dual Intel Xeon Quad Core/Dual Core 5400/5300/5200/5100 Series
processors (w/771 LGA) with a front side bus speed of up to 1.333 GHz. With
dual 64-bit Xeon Quad Core/Dual Core 5400/5300/5200/5100 Series processors
built-in, the X7DCL-3/X7DCL-i offers substantial functionality enhancements to
the motherboards based on the Intel Core microarchitecture while remaining
compatible with the IA-32 software. The features supported by this motherboard
include Intel Virtualization Technology, Enhanced Intel SpeedStep technology,
Extended Memory 64 Technology (EM64T) and Native DDR 2 DIMM modules.
These features allow the motherboard to operate at much higher speeds with
lower power consumption in much safer thermal environments than the traditional
motherboards. The X7DCL-3/X7DCL-i is ideal for complex business applications
and servers. Please refer to the motherboard specifications pages on our web site
intended to be installed and serviced by professional technicians.
Manual Organization
Chapter 1 describes the features, specifications and performance of the
mainboard and provides detailed information about the chipset.
Chapter 2 provides hardware installation instructions. Read this chapter when
installing the processor, memory modules and other hardware components into the
system. If you encounter any problems, see Chapter 3, which describes trouble-
shooting procedures for video, memory and system setup stored in the CMOS.
Chapter 4 includes an introduction to the BIOS, and provides detailed information
on running the CMOS Setup utility.
Appendix A lists BIOS POST Error Codes. Appendix B and Appendix C provide
the Windows OS and other Software Installation Instructions.
Conventions Used in the Manual:
Special attention should be given to the following symbols for proper installation
and to prevent damage done to the components or injury to yourself.
Danger/Caution: Instructions to be strictly followed to prevent catastrophic
system failure or to avoid bodily injury.
Warning: Important information given to ensure proper system installation or
to prevent damage to the components.
Note: Additional Information given to ensure correct system setup.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
Table of Contents
Preface
About This Manual ........................................................................................... iii
Manual Organization ........................................................................................ iii
Conventions Used in the Manual.......................................................................iii
Chapter 1: Introduction
1-1 Overview ......................................................................................................... 1-1
Checklist ................................................................................................... 1-1
Contacting Supermicro ............................................................................. 1-2
X7DCL-3/i Image ....................................................................... 1-3
X7DCL-3/i Layout ...................................................................... 1-4
Quick Reference ...................................................................................... 1-5
Motherboard Features................................................................................ 1-6
Intel 5100 Chipset: System Block Diagram ............................................. 1-8
1-2 Chipset Overview ........................................................................................... 1-9
1-3 Special Features ........................................................................................... 1-10
1-4 PC Health Monitoring .................................................................................... 1-10
1-5 ACPI Features .............................................................................................. 1-11
1-6 Power Supply ............................................................................................... 1-12
1-7 Super I/O ........................................................................................................ 1-12
Chapter 2: Installation
2-1 Static-Sensitive Devices ................................................................................. 2-1
Precautions................................................................................................ 2-1
Unpacking ................................................................................................ 2-1
2-2 Processor and Heatsink Installation ............................................................... 2-2
2-3 Installing DIMMs ............................................................................................. 2-6
2-4 Control Panel Connectors and IO Ports ......................................................... 2-8
Back Panel Connectors/IO Ports................................................................... 2-8
Front Control Panel ....................................................................................... 2-9
Front Control Panel Pin Definitions............................................................. 2-10
NMI Button ............................................................................................. 2-10
Power LED ............................................................................................. 2-10
HDD LED .............................................................................................. 2-11
NIC1/NIC2 LED Indicators ..................................................................... 2-11
Overheat/Fan Fail LED ......................................................................... 2-12
Power Fail LED ........................................................................................ 2-12
Reset Button ......................................................................................... 2-13
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Power Button .......................................................................................... 2-13
2-5 Connecting Cables ....................................................................................... 2-14
ATX Power Connector .......................................................................... 2-14
Processor Power Connector ................................................................. 2-14
Universal Serial Bus (USB)..................................................................... 2-15
Fan Headers .......................................................................................... 2-16
Chassis Intrusion .................................................................................... 2-16
ATX PS/2 Keyboard and Mouse Ports..................................................... 2-17
Serial Ports.............................................................................................. 2-17
Wake-On-Ring.......................................................................................... 2-18
Wake-On-LAN .......................................................................................... 2-18
GLAN 1/2 (Ethernet) Ports....................................................................... 2-19
Speaker/Power LED Header .................................................................. 2-19
Alarm Reset.............................................................................................. 2-20
Power Supply Failure/Power Fault........................................................... 2-20
VGA Connector ........................................................................................ 2-21
SGPIO Headers ....................................................................................... 2-21
Power SMB (I2C)...................................................................................... 2-22
BP Power SMB (I2C) ................................................................................ 2-22
Keylock..................................................................................................... 2-23
2-6
J..u..m...p..e..r...S..e..t.t.i.n..g..s................................................................... 2-24
Explanation of Jumpers ......................................................................... 2-24
GLAN Enable/Disable ............................................................................ 2-24
CMOS Clear ............................................................................................ 2-25
Watch Dog................................................................................................ 2-25
VGA Enable/Disable................................................................................. 2-26
I2C Bus to PCI Slots................................................................................. 2-26
SAS Enable.............................................................................................. 2-27
Software RAID Enable ............................................................................. 2-27
O...n..b..o..a..r.d...L..E...D...I.n..d..i.c..a..t.o..r.s.......................................... 2-28
2-7
2-8
GLAN LEDs.............................................................................................. 2-28
Onboard Power LED................................................................................ 2-28
System Status LED.................................................................................. 2-29
CPU_VRM Overheat LEDs...................................................................... 2-29
System Status LED.................................................................................. 2-30
F...lo..p..p..y..,..S...I.M...L..C...I.P...M..I2a-n3d1 Hard Disk
Floppy Connector.................................................................................... 2-31
IDE Connector.......................................................................................... 2-32
SIMLC IPMI Slot...................................................................................... 2-32
v
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
Chapter 3: Troubleshooting
3-1 Troubleshooting Procedures ........................................................................... 3-1
Before Power On....................................................................................... 3-1
No Power................................................................................................... 3-1
No Video .................................................................................................. 3-1
Losing the System’s Setup Configuration ................................................ 3-1
Memory Errors........................................................................................... 3-2
3-2 Technical Support Procedures ........................................................................ 3-2
3-3 Frequently Asked Questions ........................................................................... 3-3
3-4 Returning Merchandise for Service................................................................. 3-3
Chapter 4: BIOS
4-1 Introduction ....................................................................................................... 4-1
4-2 Running Setup ................................................................................................. 4-2
4-3 Main BIOS Setup ............................................................................................. 4-2
4-4 Advanced Setup ............................................................................................... 4-7
4-5 Security Setup ............................................................................................... 4-20
4-6 Boot Setup...................................................................................................... 4-21
4-7 Exit.................................................................................................................. 4-22
Appendices:
Appendix A: BIOS POST Error Beep Codes .............................................................A-1
Appendix B: Installing the Windows OS ....................................................................B-1
Appendix C: Installing Other Software Programs and Drivers...................................C-1
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
Chapter 1
Introduction
1-1
Overview
Checklist
Congratulations on purchasing your computer motherboard from an acknowledged
leader in the industry. Supermicro boards are designed with the utmost attention to
detail to provide you with the highest standards in quality and performance. Check
that the following items have all been included with your motherboard. If anything
listed here is damaged or missing, contact your retailer.
All the following items are included in the Retail Box only.
One (1) Super Micro Mainboard
One (1) ribbon cable for IDE devices (CBL-0036L-2)
One (1) floppy ribbon cable (CBL-0022L)
Eight (8) SATA cables (CBL-0044L) (X7DCL-3)
Six (6) SATA cables (CBL-0044L) (X7DCL-i)
One (1) I/O backpanel shield (CSE-PT07L)
One (1) CPU Retention Module (SKT-0159)
One (1) Supermicro CD containing drivers, software and utilities (CDR-X7)
One (1) User's/BIOS Manual (MNL-0957)
Optional
(For SAS HostRAID 5)
One (1) I-Button (AOC-iBUTTON 68) (X7DCL-3)
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
Contacting Supermicro
Headquarters
Address:
Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
+1 (408) 503-8000
Tel:
Fax:
Email:
+1 (408) 503-8008
[email protected] (General Information)
Web Site:
Europe
Address:
Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
+31 (0) 73-6400390
Tel:
Fax:
Email:
+31 (0) 73-6416525
[email protected] (General Information)
[email protected] (Customer Support)
Asia-Pacific
Address:
Super Micro, Taiwan
4F, No. 232-1, Liancheng Rd.
Chung-Ho 235, Taipei County
Taiwan, R.O.C.
Tel:
+886-(2) 8226-3990
+886-(2) 8226-3991
Fax:
Web Site:
Technical Support:
Email:
Tel:
886-2-8228-1366, ext.132 or 139
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
X7DCL-3/X7DCL-i Image
Note: The drawings and pictures shown in this manual were based on the
latest PCB Revision available at the time of publishing of the manual. The
motherboard you’ve received may or may not look exactly the same as the
graphics shown in the manual.
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
X7DCL-3/X7DCL-i Motherboard Layout
(not drawn to scale)
JPWF1
CPU1 VRM OH LED
LED5
SMB_PS
JAR
JPW1
8-Pin PWR
JPW2
24-Pin PWR
JKM1
JBS1
DIMM2A
CPU1
DIMM1A
DIMM2B
DIMM1B
JCOM1
JVGA1
DIMM2C
DIMM1C
X7DCL-3/i
JLAN1
JLAN2
CPU2
JPL2
LAN
CTRL
Intel
5100
North Bridge
I-Button
Fan
Fan
2
3
LED6
LAN
CTRL
CPU2 VRM OH LED
JP2
JP1
SP1
Buzzer
Slot6 PCI-E x8
Intel
Slot5 PCI-E x8
ICH9R
PWR LED
LED3
South Bridge
Slot4 PCI-E x4(in x8 slot)
VGA
JF1
CTRL
JBT1
LED1
BIOS
JPG1
Slot3 PCI 33MHz
Battery
LSI
SAS
CTRL
ITE
SAS-GPIO1
SAS-GPIO0
Slot2 PCI 33MHz
J10
J9
S I/O
CTRL
JWD1
JWOL1
JFDD1
JL1
JPA2
LED4
Slot1 PCI 33MHz
SIMLC
USB4/5
BPI
System Status LED
JIDE1
COM2
USB2/3
JUSB2
2
C
Fan 4
Notes:
1. Jumpers not indicated are for test purposes only.
2. See Chapter 2 for detailed information on jumpers, I/O ports and JF1 front panel
connections.
3. " " indicates the location of Pin 1.
4. When LED3 is on, make sure to unplug the power cable before removing or
installing components.
5. All features and components related to SAS are available on the X7DCL-3 only,
including SAS Connectors, the LSI SAS HostRAID Controller, and the I-Button
socket. I-Button is used to support RAID 5 (optional.)
1-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
Quick Reference (X7DCL-3/X7DCL-i)
Jumper
JBT1
Description
Default Setting
CMOS Clear
See Chapter 2
JI2C1/JI2C2
JPG1
SMB to PCI/PCI-Exp Slots
VGA Enable
Open (Disabled)
Pins 1-2 (Enabled)
Pins 1-2 (Enabled)
Closed (Software RAID)
Pins 1-2 (Enabled)
Pins 1-2 (Reset)
JPA1 (Note)
JPA2 (Note)
JPL1/ JPL2
JWD
SAS Enable
Software RAID/IT RAID Mode
GLAN1/GLAN2 Enable
Watch Dog
Connector
BPI2C
Description
Back Panel Power System Management (I2C) Header
COM1/COM2 Serial Port and Header
Fans 1-2: CPU Fans, Fans 3-6: System cooling fans
Floppy Disk Drive Connector (JFDD1)
Front Control Panel Connector (JF1)
IDE Hard Drive
COM1/COM2
FAN 1-6
Floppy
FP Control
IDE
J7/J8/9/10
Serial-Links General Purpose Input/Output Headers
(J7/J8: SATA T-SGPIO 0/1, J9/J10: SAS T-SGPIO 0/1)
Alarm Reset Header
JAR1
JD1
Power LED(pins1-3)/SpeakerHeader (pins 4-7)
I-Button Socket
JIBTN1
JL1
Chassis Intrusion Header
JPW1
+12V 8-pin PWR
JPW2
Primary 24-Pin ATX PWR Connector
Power Supply Failure (See Chapter 2)
BP USB0/1 (JUSB1), FP USB2/3/4/5 (JUSB2/3)
Wake-on-LAN Header
JPWF1
JUSB1/JUSB2/3
JWOL
JWOR
Wake-on-Ring Header
Keylock
LAN1/2
PWR I2C
SAS0-SAS7 (Note)
SATA0-SATA5
SIMLC
Keylock Header (JKEY1)
G-bit Ethernet Ports 1/2
Power System Management (I2C) Header (JPI2C1)
Serial Attached SCSI Connectors (#0-#7) (X7DCL-3)
SATA 0-5 Connectors
IPMI SIMLC Slot (JIPMI)
VGA
VGA Port
LED Indicator
LED1
Description
SAS LED
LED3/LED4
LED5/LED6
Power LED (LED3)/System Status LED (LED4)
CPU1/CPU2 VRM Overheat (respectively)
Note: SAS is available on the X7DCL-3 only.
1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
Motherboard Features
CPU
•
Dual Intel® 64-bit Xeon LGA 771 Quad Core/Dual Core 5400/5300/5200/5100
Series processors at a front side bus speed of 1333 MHz/1066 MHz
Memory
Six 240-pin DIMM sockets with support up to 32 GB Single-Rank, Registered/
•
ECC DDR2 667/533 Memory.
Note: PCB revision 1.1a and later will now support up to 48 GBs of Single-
Rank, Registered/ECC DDR2 667/533 Memory (See Section 2-3 in Chapter
2 for DIMM Slot Population.)
Chipset
•
Intel 5100 chipset, including: the 5100 Memory Control Hub (MCH) and the
ICH9R South Bridge
Expansion Slots
•
•
•
Two PCI-E x8 slot (Slot 5/Slot 6), and one in PCI-E x4 (in x8) slot (Slot 4)
Three 32-bit PCI 33 MHz slot (Slot 1/Slot 2/Slot 3)
One SIMLC IPMI Slot (Slot 0)
BIOS
•
•
8 Mb Phoenix® Flash ROM
DMI 2.3, PCI 2.2, ACPI 1.0, Plug and Play (PnP), USB Keyboard support,
Hardware BIOS Virus Protection and SMBIOS 2.3
PC Health Monitoring
•
Onboard voltage monitors for CPU core voltage, Memory voltage, +1.8V, +3.3V,
+5V, +12V, -12V, +3.3V standby, +5V standby and VBAT)
Fan status monitor with firmware control
•
•
•
•
•
•
•
•
•
•
•
CPU/chassis temperature monitors
Low noise fan speed control
Platform Environment Control Interface (PECI) ready
CPU fan auto-off in sleep mode
Pulse Width Modulation (PWM) fan control
I2C temperature sensing logic
Thermal Monitor 2 (TM2) support
CPU slow-down on temperature overheat
CPU thermal trip support for processor protection
Power-up mode control for recovery from AC power loss
1-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
•
•
Chassis intrusion detection
System resource alert via Supero Doctor III
ACPI Features
•
•
•
•
Slow blinking LED for suspend state indicator
Main switch override mechanism
ACPI Power Management
Power-on mode for power recovery
Onboard I/O
•
Six SATA ports support RAID 0, 1, 10 and 5 (in the Windows OS environ-
ment)
•
•
•
•
•
•
•
•
•
Eight SAS ports supports RAID 0, 1, 10 and 5. (For X7DCL-3 only)
One SIMLC IPMI 2.0 socket
Intel 82573V and 82573L LAN chips support two Giga-bit LAN ports
One EIDE Ultra DMA/100 bus master interface
One floppy port interface
Two COM ports(1 header, 1 port)
Up to six USB 2.0 (Universal Serial Bus) (2 ports, 4 Headers)
XGI Volari Z9s 32 MB Graphic Controller
Super I/O: Winbond W83627HG
Other
•
•
•
•
•
External modem ring-on
Wake-on-LAN (WOL)
Wake-on-Ring (WOR)
Console redirection
Onboard Fan Speed Control by Thermal Management via BIOS
CD/Diskette Utilities
Device drivers and Software
Dimensions
•
•
ATX 12.05" x 10" (306.1mm x 254 mm)
1-7
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
PROCESSOR#1
ISL6312A
ISL6312A
PROCESSOR#2
1067/1333
MT/S
1067/1333
MT/S
#0-3
#0-2
#0-1
PCI-EXP x8
PORT
#2,3
#1-3
#1-2
#1-1
MCH
Intel 5100
#7
#6
#5
#4
#3
#2
#1
#0
PCI-EXP x8
PCI-EXP x8
PORT
#4,5
PORT
#6,7
3.0 Gb/S
PORT
#0
LSI 1068E
#5
#4
#3
#2
#1
#0
PCI-EXP x1
DMI
RJ45
RJ45
82573V
82573L
LANE5
3.0 Gb/S
PCI-EXP x1
LANE6
ICH9R
LANE1/2/3/4
#5
#4
#3
#2
#1
DDR2 SDRAM 32MB
#0
USB 2.0
PCI 33MHz
VGA
CONN
VGA
Volari Z9S
LPC
IDE
IT8213F
PCI-33
PCI-33
PCI-33
SIO
W83627HG
FWH
MS
KB
COM2
INTERNAL/SOL
COM1
External
Block Diagram of the Intel 5100 Chipset
Note: This is a general block diagram. Please see the previous Motherboard
Features pages for details on the features of each motherboard.
1-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
1-2
Chipset and Processor Features Overview
Built upon the functionality and the capability of the Intel 5100 chipset, the X7DCL-
3/X7DCL-i motherboard provides the performance and feature set required for
dual processor-based high-end servers with configuration options optimized for
intensive computing, high energy-efficiency and complex business applications.
The 5100 chipset supports single or dual Intel Xeon 64-bit Quad Core/Dual Core
5400/5300/5200/5100 Series processors with front side bus speeds of up to 1.333
GHz. The chipset consists of the 5100 Memory Controller Hub (MCH), Intel I/O
Controller Hub (ICH9R) and the I/O subsystem.
The 5100 Memory Controller Hub (MCH)
The Intel 5100 MCH chip is designed for symmetric multiprocessing across two
independent front side bus interfaces. Each front side bus uses a 64-bit wide,
1066/1333 MTS data bus capable of transferring data at 8.5/10.6 GB/s for a total
bandwidth of 17/21.3 GB/s. The MCH supports a 36-bit wide address bus and up
to six DDR2 667 MHz/533 MHz DIMM modules, providing a total memory capac-
ity of up to 32 GB.
The 5100 MCH also provides six x4 PCI-Express interfaces and one x4 DMI
Interface to the ICH9R. Each PCI Express port on the MCH provides 4 GB/s bi-
directional bandwidth if configured as a x8 port, or 2 GB/s bi-directional bandwidth
if configured as a x4 port.
The Ninth Generation I/O Controller Hub (ICH9)
The I/O Controller ICH9R provides the data buffering and interface arbitration
required for the system to operate efficiently. It also provides the bandwidth needed
for the system to maintain its peak performance. The Direct Media Interface (DMI)
provides the connection between the MCH and the ICH9R. The ICH9R supports
up to six PCI-Express x1 slots, six Serial ATA ports and twelve USB 2.0 ports.
In addition, the ICH9R offers the Intel Matrix Storage Technology which provides
various RAID options for data protection and rapid data access. It also supports the
next generation of client management through the use of PROActive technology in
conjunction with Intel's next generation Gigabit Ethernet controllers.
1-9
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
1-3
Special Features
Recovery from AC Power Loss
BIOS provides a setting for you to determine how the system will respond when
AC power is lost and then restored to the system. You can choose for the system
to remain powered off (in which case you must hit the power switch to turn it back
on) or for it to automatically return to a power-on state. See the Power Lost Control
setting in the Advanced BIOS Setup section to change this setting. The default
setting is Last State.
1-4
PC Health Monitoring
This section describes the PC health monitoring features of the X7DCL-3/X7DCL-
i. All have an onboard System Hardware Monitor chip that supports PC health
monitoring.
Onboard Voltage Monitors
An onboard voltage monitor will scan for the CPU Cores, Chipset Voltage, +1.8V,
+3.3V, +5V, +12V, -12V, +3.3V Standby, +5V Standby and VBAT continuously.
Once a voltage becomes unstable, a warning is given or an error message is sent
to the screen. Users can adjust the voltage thresholds to define the sensitivity
of the voltage monitor.
Fan Status Monitor with Firmware Control
The PC health monitor can check the RPM status of the cooling fans. The onboard
CPU and chassis fans are controlled by Thermal Management via BIOS (under
Hardware Monitoring in the Advanced Setting).
Environmental Temperature Control
The thermal control sensor monitors the CPU temperature in real time and will turn
on the thermal control fan whenever the CPU temperature exceeds a user-defined
threshold. The overheat circuitry runs independently from the CPU. Once it detects
that the CPU temperature is too high, it will automatically turn on the thermal fan
control to prevent any overheat damage to the CPU. The onboard chassis thermal
circuitry can monitor the overall system temperature and alert users when the chas-
sis temperature is too high.
System Resource Alert
This feature is available when used with Supero Doctor III in the Windows OS
environment or used with Supero Doctor II in Linux. Supero Doctor is used to
notify the user of certain system events. For example, if the system is running low
on virtual memory and there is insufficient hard drive space for saving the data,
1-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
you can be alerted of the potential problem. You can also configure Supero Doctor
to provide you with warnings when the system temperature goes beyond a pre-
defined range.
1-5
ACPI Features
ACPI stands for Advanced Configuration and Power Interface. The ACPI specifica-
tion defines a flexible and abstract hardware interface that provides a standard
way to integrate power management features throughout a PC system, including
its hardware, operating system and application software. This enables the system
to automatically turn on and off peripherals such as CD-ROMs, network cards, hard
disk drives and printers. This also includes consumer devices connected to the PC
such as VCRs, TVs, telephones and stereos.
In addition to enabling operating system-directed power management, ACPI
provides a generic system event mechanism for Plug and Play and an operating
system-independent interface for configuration control. ACPI leverages the Plug
and Play BIOS data structures while providing a processor architecture-independent
implementation that is compatible with Windows 2000, Windows XP and Windows
2003 Servers.
Slow Blinking LED for Suspend-State Indicator
When the CPU goes into a suspend state, the chassis power LED will start blinking
to indicate that the CPU is in suspend mode. When the user presses any key, the
CPU will wake-up and the LED will automatically stop blinking and remain on.
Main Switch Override Mechanism
When an ATX power supply is used, the power button can function as a system
suspend button to make the system enter a SoftOff state. The monitor will be
suspended and the hard drive will spin down. Pressing the power button again
will cause the whole system to wake-up. During the SoftOff state, the ATX power
supply provides power to keep the required circuitry in the system "alive". In case
the system malfunctions and you want to turn off the power, just press and hold
the power button for 4 seconds. This option can be set in the Power section of the
BIOS Setup routine.
External Modem Ring-On
Wake-up events can be triggered by a device such as the external modem ringing
when the system is in the Standby or Off state. Note that external modem ring-on
can only be used with an ATX 2.01 (or above) compliant power supply.
Wake-On-LAN is defined as the ability of a management application to remotely
power up a computer that is powered off. Remote PC setup, up-dates and asset
tracking can occur after hours and on weekends so that daily LAN traffic is kept
1-11
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
to a minimum and users are not interrupted. The motherboard has a 3-pin header
(WOL) to connect to the 3-pin header on a Network Interface Card (NIC) that has
WOL capability. In addition, an onboard LAN controller can also support WOL
without any connection to the WOL header. The 3-pin WOL header is to be used
with a LAN add-on card only.
Note: Wake-On-LAN requires an ATX 2.01 (or above) compliant power supply.
1-6
Power Supply
As with all computer products, a stable power source is necessary for proper and
reliable operation. It is even more important for processors that have high CPU
clock rates.
The X7DCL-3/X7DCL-i can only accommodate 24-pin ATX power supply. Although
most power supplies generally meet the specifications required by the motherboard,
some are inadequate. You should use one that will supply at least 400W of power.
In addition, the 12V 8-pin is also required for adequate power supply to the CPU.
Also your power supply must supply 1.5A for the Ethernet ports.
It is strongly recommended that you use a high quality power supply that meets
ATX power supply Specification 2.02 or above. It must also be SSI compliant (info
present, you may choose to install a line filter to shield the computer from noise. It is
recommended that you also install a power surge protector to help avoid problems
caused by power surges.
1-7
Super I/O
The disk drive adapter functions of the Super I/O chip include a floppy disk drive
controller that is compatible with industry standard 82077/765, a data separator,
write pre-compensation circuitry, decode logic, data rate selection, a clock generator,
drive interface control logic and interrupt and DMA logic. The wide range of functions
integrated onto the Super I/O greatly reduces the number of components required
for interfacing with floppy disk drives. The Super I/O supports 360 K, 720 K, 1.2
M, 1.44 M or 2.88 M disk drives and data transfer rates of 250 Kb/s, 500 Kb/s or
1 Mb/s. It also provides two high-speed, 16550 compatible serial communication
ports (UARTs). Both UARTs provide legacy speed with baud rate of up to 115.2
Kbps as well as an advanced speed with baud rates of 250 K, 500 K, or 1 Mb/s,
which support higher speed modems.
The Super I/O supports one PC-compatible printer port (SPP), Bi-directional Printer
Port (BPP), Enhanced Parallel Port (EPP) or Extended Capabilities Port (ECP).
1-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
The Super I/O provides functions that comply with ACPI (Advanced Configuration
and Power Interface), which includes support of legacy and ACPI power manage-
ment through an SMI or SCI function pin. It also features auto power management
to reduce power consumption.
1-13
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
Notes
1-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
Chapter 2
Installation
2-1
Static-Sensitive Devices
Electro-Static Discharge (ESD) can damage electronic components. To prevent
damage to your system board, it is important to handle it very carefully. The fol-
lowing measures are generally sufficient to protect your equipment from ESD.
Precautions
•
•
Use a grounded wrist strap designed to prevent static discharge.
Touch a grounded metal object before removing the board from the antistatic
bag.
•
Handle the board by its edges only; do not touch its components, peripheral
chips, memory modules or gold contacts.
•
•
When handling chips or modules, avoid touching their pins.
Put the motherboard and peripherals back into their antistatic bags when not
in use.
•
•
For grounding purposes, make sure your computer chassis provides excellent
conductivity between the power supply, the case, the mounting fasteners and
the motherboard.
Use only the correct type of onboard CMOS battery as specified by the
manufacturer. Do not install the onboard battery upside down to avoid possible
explosion.
Unpacking
The motherboard is shipped in antistatic packaging to avoid static damage. When
unpacking the board, make sure the person handling it is static protected.
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
2-2
Processor and Heatsink Fan Installation
When handling the processor package, avoid placing direct pressure
on the label area of the fan.
!
Notes:
•
Always connect the power cord last and always remove it before adding, re-
moving or changing any components. Make sure that you install the processor
into the CPU socket before you install the CPU heatsink.
•
Intel's boxed Xeon CPU package contains the CPU fan and heatsink assembly.
If you buy a CPU separately, make sure that you use only Intel-certified multi-
directional heatsink and fan.
•
•
Make sure to install the motherboard into the chassis before you install the
CPU heatsink and fan.
When purchasing a motherboard with an LGA 771 CPU Socket, make sure
that the CPU plastic cap is in place, and none of the CPU Socket pins are
bent; otherwise, contact the retailer immediately.
•
Refer to the Chipset/MB Features Section for more details on CPU support.
Installing the LGA771 Processor
Load Lever
PnP Cap on
top of the
1. Press the load lever to release
the load plate, which covers the
CPU socket, from its locking
position.
Load Plate
2. Gently lift the load lever to open
the load plate.
Load Plate
(with PnP Cap
attached)
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
North Center Edge
Loading the Processor into the Socket
1. Use your thumb and your index
finger to hold the CPU at the North
Center Edge and the South Center
Edge of the CPU.
2. Align CPU Pin1 (the CPU corner
marked with a triangle) against the
socket corner that is marked with a
triangle cutout.
South Center Edge
gold dot
Socket Key
3. Align the CPU key that is the semi-
circle cutout below a gold dot against
the socket key, the notch on the
same side of the triangle cutout on
the socket.
(Socket Notch)
CPU Key (semi-
circle cutout)
below the circle.
4. Once aligned, carefully lower the
CPU straight down to the socket.
(Do not drop the CPU on the socket.
Do not move the CPU horizontally
or vertically. Do not rub the CPU
against the surface or against any
pins of the socket to avoid damage
to the CPU or the socket.)
Corner with a
triangle cutout
CPU Pin1
Load Lever
5. With the CPU installed in the socket,
inspect the four corners of the
CPU to make sure that the CPU is
properly installed. Then, close the
load plate.
CPU in the CPU socket
6. Use your thumb to gently push the
load lever down to lock it.
7.
If the CPU is properly installed into
the socket, the plastic cap will be
automatically released from the load
plate when the clip is pushed in the
clip lock. Remove the plastic cap
from the motherboard.
Plastic cap
is released
from the
load plate
if the CPU
properly in-
stalled.
!
Warning: Please save the plastic
PnP cap. The motherboard must be
shipped with the PnP cap properly in-
stalled to protect socket pins. Shipment
without the PnP cap properly installed will
cause damage to the socket pins.
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
Installing the Heatsink
CEK Passive Heatsink
1. Do not apply any thermal grease to the
heatsink or the CPU die; the required
amount has already been applied.
2. Place the heatsink on top of the CPU
so that the four mounting holes are
aligned with those on the retention
mechanism.
Screw#1
Screw#2
3. Screw in two diagonal screws (ie the
#1 and the #2 screws) until just snug (-
do not fully tighten the screws to avoid
possible damage to the CPU.)
Screw#1
4. Finish the installation by fully tighten-
ing all four screws.
Screw#2
To Remove the Heatsink
Warning: We do not recommend that the CPU or the heatsink be removed.
However, if you do need to uninstall the heatsink, please follow the instructions
on the next page to uninstall the heatsink to prevent damage done to the CPU
or the CPU socket.
!
1. Unscrew and remove the heatsink screws
from the motherboard in the sequence as
shown in the picture on the right.
2. Hold the heatsink as shown in the pic-
ture on the right and gently wriggle the
heatsink to loosen it from the CPU. (Do
not use excessive force when wriggling
the heatsink!!)
3. Once the heatsink is loosened, remove
the it from the CPU socket.
2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
4. Clean the surface of the CPU
and the heatsink to get rid of the
old thermal grease. Reapply the
proper amount of thermal grease
on the surface before you re-install
the CPU and the heatsink.
Mounting the Motherboard in the Chassis
All motherboards have standard mounting holes to fit different types of chassis.
Make sure that the locations of all the mounting holes for both motherboard and
chassis match. Make sure that the metal standoffs click in or are screwed in
tightly. Then, use a screwdriver to secure the motherboard onto the motherboard
tray. (Note: some components are very close to the mounting holes. Please take
precautionary measures to prevent damage done to these components when you
install the motherboard into the chassis.)
Caution: To avoid damaging the motherboard and its components, please do
not use a force greater than 8 lb/inch on each mounting screw during mother-
board installation.
2-3
Installing DIMMs
Note: Check the SuperMicro web site for recommended memory modules.
CAUTION
Exercise extreme care when installing or removing DIMM
modules to prevent any possible damage. Also note that the
memory is interleaved to improve performance.
DIMM Installation
1. Insert the desired number of DIMMs into the memory slots, starting with DIMM
#1A. The memory scheme is interleaved, so you must install two modules
at a time, beginning with DIMM 1A, DIMM 2A, then DIMM 1B, DIMM 2B, and
DIMM 1C, DIMM 2C. (See the Memory Installation Table Below.)
2. Insert each DIMM module vertically into its slot. Pay attention to the notch along
the bottom of the module to prevent inserting the DIMM module incorrectly.
3. Gently press down on the DIMM module until it snaps into place in the slot.
Repeat for all modules (See step 1 above.)
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
Memory Support
The X7DCL-3/X7DCL-i supports up to 48 GB Single-Rank/Dual Rank, Registered
ECC DDR2 667/533 in 6 DIMMs (The amount and type of memory supported is
dependent on the PCB revision. See Note 1 Below). Populating DIMM slots with
pairs of memory modules of the same size and same type will result in Inter-
leaved Memory which will improve memory performance.
Note 1: For the PCB Rev. 1.1 motherboard, Slots 1A and 2A support Dual-Rank
modules; however, Slots 1B, 2B, 1C and 2C support Single-Rank memory only
(Maximum of 32 GB). The PCB Rev. 1.1a board supports 6 Dual-Rank or 6 Single-
Rank modules (Maximum of 48 GB).
Optimized DIMM Population Configurations
Channel 0
No. of
DIMMs
Channel 1
2DIMMs
4DIMMs
6DIMMs
DIMM 1A
DIMM 1A
DIMM 1A
------
DIMM 1B
DIMM 1B
------
------
DIMM 1C
DIMM 2A
DIMM 2A
DIMM 2A
------
DIMM 2B
DIMM 2B
------
------
DIMM 2C
(Notes: i. DIMM slot# specified: DIMM slot to be populated; “---“: DIMM slot not to be
populated. ii. Both Registered ECC DDR2 667MHz and 533 MHz DIMMs are supported;
however, you need to use the memory modules of the same speed and of the same type on
a motherboard. iii. For memory to work properly, you need to follow the restrictions listed
above. )
Note 2: Due to OS limitations, some operating systems may not show more than
4 GB of memory.
Note 3: Due to memory allocation to system devices, memory remaining available
for operational use will be reduced when 4 GB of RAM is used. The reduction in
memory availability is disproportional. (Refer to the following Memory Availability
Table for details. For Microsoft Windows users: Microsoft implemented a design
change in Windows XP with Service Pack 2 (SP2) and Windows Vista. This change
is specific to the Physical Address Extension (PAE) mode behavior which improves
driver compatibility. For more information, please read the following article at Micro-
2-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
Possible System Memory Allocation & Availability
System Device
Size
Physical Memory
Remaining (-Available)
(4 GB Total System Memory)
Firmware Hub flash memory (System BIOS)
Local APIC
1 MB
3.99
3.99
3.99
3.99
3.76
3.51
3.01
4 KB
Area Reserved for the chipset
I/O APIC (4 Kbytes)
2 MB
4 KB
PCI Enumeration Area 1
PCI Express (256 MB)
256 MB
256 MB
PCI Enumeration Area 2 (if needed) -Aligned on 256- 512 MB
MB boundary-
VGA Memory
16 MB
1 MB
2.85
2.84
2.84
TSEG
Memory available to OS and other applications
Installing and Removing DIMMs
DDR2 DIMM
X7DCL-3/i
To Install: Insert module vertically and press
down until it snaps into place. Pay attention to the
alignment notch at the bottom.
To Remove:
Top View of DDR2 Slot
Use your thumbs to
gently push the re-
lease tabs near both
ends of the module
to release it from the
slot.
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
2-4
Control Panel Connectors/IO Ports
The I/O ports are color coded in conformance with the PC 99 specification. See
the figure below for the colors and locations of the various I/O ports.
Back Panel Connectors/IO Ports
X7DCL-3/i
2
4
5
6
7
8
1
3
Back Panel I/O Port Locations and Definitions
Back Panel Connectors
1. Keyboard (Purple)
2. PS/2 Mouse (Green)
3. Back Panel USB Port 0
4. Back Panel USB Port 1
5. COM Port 1 (Turquoise)
6. VGA Port (Blue)
7. Gigabit LAN 1
8. Gigabit LAN 2
(See Section 2-5 for details.)
2-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
Front Control Panel
JF1 contains header pins for various buttons and indicators that are normally lo-
cated on a control panel at the front of the chassis. These connectors are designed
specifically for use with Super Micro server chassis. See the figure below for the
descriptions of the various control panel buttons and LED indicators. Refer to the
following section for descriptions and pin definitions.
JF1 Header Pins
20 19
Ground
NMI
X
X
X7DCL-3/i
Vcc
Power LED
Vcc
Vcc
HDD LED
NIC1 LED
NIC2 LED
Vcc
Vcc
OH/Fan Fail LED
PWR Fail LED
Vcc
Reset
Reset Button
Power Button
Ground
Ground
PWR
2
1
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
Front Control Panel Pin Definitions
NMI Button
NMI Button
Pin Definitions (JF1)
The non-maskable interrupt button
header is located on pins 19 and 20
of JF1. Refer to the table on the right
for pin definitions.
Pin# Definition
19
20
Control
Ground
Power LED
Pin Definitions (JF1)
Power LED
The Power LED connection is located
on pins 15 and 16 of JF1. Refer to the
table on the right for pin definitions.
Pin# Definition
15
16
+5V
Ground
A. NMI
B. PWR LED
20 19
Ground
X
NMI
X
A
BPower LED
Vcc
X7DCL-3/i
Vcc
Vcc
Vcc
Vcc
Vcc
HDD LED
NIC1 LED
NIC2 LED
OH/Fan Fail LED
PWR Fail LED
Reset
Reset Button
Power Button
Ground
Ground
PWR
2
1
2-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
HDD LED
The HDD LED connection is located
on pins 13 and 14 of JF1. Attach a
hard drive LED cable here to display
disk activity (for any hard drives on
the system, including SAS, Serial
ATA and IDE). See the table on the
right for pin definitions.
HDD LED
Pin Definitions (JF1)
Pin# Definition
13
14
+5V
HD Active
NIC1/NIC2 LED Indicators
The NIC (Network Interface Control-
ler) LED connection for GLAN port1
is located on pins 11 and 12 of JF1
and the LED connection for GLAN
Port2 is on Pins 9 and 10. Attach the
NIC LED cables to display network
activity. Refer to the table on the right
for pin definitions.
GLAN1/2 LED
Pin Definitions (JF1)
Pin# Definition
9/11
Vcc
10/12 Ground
A. HDD LED
B. NIC1 LED
C. NIC2 LED
20 19
Ground
X
NMI
X
X7DCL-3/i
Vcc
Power LED
Vcc
Vcc
Vcc
Vcc
Vcc
HDD LED
A
B NIC1 LED
NIC2 LED
C
OH/Fan Fail LED
PWR Fail LED
Reset
Reset Button
Power Button
Ground
Ground
PWR
2
1
2-11
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
Overheat/Fan Fail LED (OH)
OH/Fan Fail LED
Pin Definitions (JF1)
Connect an LED to the OH/Fan Fail
connection on pins 7 and 8 of JF1
to provide advanced warnings of
chassis overheating or fan failure.
Refer to the table on the right for pin
definitions.
Pin# Definition
7
8
Vcc
Ground
OH/Fan Fail Indicator
Status
State Definition
Off
On
Normal
Overheat
Fan Fail
Flash-
ing
Power Fail LED
PWR Fail LED
Pin Definitions (JF1)
The Power Fail LED connection is
located on pins 5 and 6 of JF1. Re-
fer to the table on the right for pin
definitions.
Pin# Definition
5
6
Vcc
Ground
A. OH/Fan Fail LED
B. PWR Supply Fail
20 19
Ground
NMI
X
X
X7DCL-3/i
Vcc
Power LED
Vcc
Vcc
Vcc
Vcc
Vcc
HDD LED
NIC1 LED
NIC2 LED
OH/Fan Fail LED
A
PWR Fail LED
B
Reset
Reset Button
Power Button
Ground
Ground
PWR
2
1
2-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
Reset Button
Reset Button
Pin Definitions (JF1)
The Reset Button connection is located
on pins 3 and 4 of JF1. Attach it to the
hardware reset switch on the computer
case. Refer to the table on the right for
pin definitions.
Pin# Definition
3
4
Reset
Ground
Power Button
The Power Button connection is located
on pins 1 and 2 of JF1. Momentarily
contacting both pins will power on/off
the system. This button can also be
configured to function as a suspend
button (with a setting in the BIOS - see
Chapter 4). To turn off the power when
set to suspend mode, press the button
for at least 4 seconds. Refer to the table
on the right for pin definitions.
Power Button
Pin Definitions (JF1)
Pin# Definition
1
2
Signal
+3V Standby
A. Reset Button
B. PWR Button
20 19
Ground
X
NMI
X
Vcc
Power LED
X7DCL-3/i
Vcc
Vcc
Vcc
Vcc
Vcc
HDD LED
NIC1 LED
NIC2 LED
OH/Fan Fail LED
PWR Fail LED
Reset
Reset Button
A
Power Button
Ground
Ground
PWR
B
2
1
2-13
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
ATX Power 24-pin Connector
2-5
Connecting Cables
Pin Definitions
Pin# Definition
Pin #
1
Definition
+3.3V
+3.3V
COM
ATX Power Connector
13
14
15
16
17
18
19
20
21
22
23
24
+3.3V
-12V
A 24-pin main power supply connec-
tor is located at JPW2, and an 8-pin
CPU PWR connector is locatged at
JPW1 on the motherboard. These
power connectors meet the SSI EPS
12V specification. See the table on
the right for pin definitions. For the
8-pin PWR (JPW1), refer to the item
below.
2
COM
PS_ON
COM
COM
COM
Res (NC)
+5V
3
4
+5V
5
COM
6
+5V
7
COM
8
PWR_OK
5VSB
+12V
9
+5V
10
11
12
+5V
+12V
COM
+3.3V
Processor Power
Connector
12V 8-pin Power CPU
Connector
Pin Definitions
In addition to the Primary ATX power
connector, the 12V 8-pin CPU PWR
connector at JPW1 must also be con-
nected to provide adequate power to
your processors. See the table on the
right for pin definitions.
Pins
Definition
Ground
+12V
1 through 4
5 through 8
Required Connection
JPWF1
CPU1 VRM OH LED
LED5
A. 24-pin ATX PWR
SMB_PS
JAR
24-Pin PWR
8-Pin PWR
B. 8-pin Processor PWR
A
B
DIMM2A
CPU1
DIMM1A
DIMM2B
DIMM1B
DIMM2C
DIMM1C
X7DCL-3/i
CPU2
JPL2
LAN
CTRL
Intel
5100
North Bridge
I-Button
Fan
Fan
2
3
LED6
LAN
CTRL
CPU2 VRM OH LED
JP2
JP1
Slot6 PCI-E x8
SP1
Buzzer
Intel
Slot5 PCI-E x8
ICH9R
PWR LED
LED3
South Bridge
Slot4 PCI-E x4(in x8 slot)
Slot3 PCI 33MHz
VGA
CTRL
JBT1
LED1
BIOS
JPG1
Battery
LSI
SAS
CTRL
ITE
SAS-GPIO1
SAS-GPIO0
Slot2 PCI 33MHz
JWOL1
S
I/O
JWD1
CTRL
JPA2
LED4
Slot1 PCI 33MHz
SIMLC
USB4/5
BPI
System Status LED
COM2
USB2/3
JL1
2
C
Fan
4
2-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
Universal Serial Bus (USB)
Back Panel USB (0/1)
Pin Definitions
There are six USB 2.0 (Universal Serial
Bus) ports/headers on the motherboard.
Two of them are Back Panel USB ports
(USB#0/1: JPUSB1), and the other
four are Front Panel USB connectors
(USB#2/3: JUSB2), or Front-Accessible
USB headers (USB#4/#5: JUSB3). See
the tables on the right for pin defini-
tions.
Pin# Definitions
1
2
3
4
5
+5V
PO-
PO+
Ground
N/A
Front Panel USB
Pin Definitions (USB2/3/4/5)
USB2/3 USB4/5
Pin #
Definition
+5V
Pin # Definition
1
2
3
4
5
1
2
3
4
5
+5V
PO-
PO-
PO+
Ground
Key
PO+
Ground
No connection
JPWF1
CPU1 VRM OH LED
LED5
A. Backpanel USB 0/1
B. Front Panel USB 2/3
C. Front Panel USB 4/5
SMB_PS
JAR
24-Pin PWR
8-Pin PWR
A
DIMM2A
CPU1
DIMM1A
DIMM2B
DIMM1B
DIMM2C
DIMM1C
X7DCL-3/i
CPU2
JPL2
LAN
CTRL
Intel
5100
North Bridge
I-Button
Fan
Fan
2
3
LED6
LAN
CTRL
CPU2 VRM OH LED
JP2
JP1
Slot6 PCI-E x8
SP1
Buzzer
Intel
Slot5 PCI-E x8
ICH9R
PWR LED
LED3
South Bridge
Slot4 PCI-E x4(in x8 slot)
Slot3 PCI 33MHz
VGA
CTRL
JBT1
LED1
BIOS
JPG1
Battery
LSI
SAS
CTRL
ITE
SAS-GPIO1
SAS-GPIO0
Slot2 PCI 33MHz
JWOL1
S
I/O
JWD1
CTRL
JP
C
LED4
B
Slot1 PCI 33MHz
SIMLC
USB4/5
System Status LED
COM2
USB2/3
JL1
2
BPI
C
Fan
4
2-15
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
Fan Headers
The X7DCL-3/X7DCL-i has four chassis/
system fan headers (Fan3 to Fan6), and
two CPU Fans (Fans 1/2). All these fans
are 4-pin fans. However, Pins 1-3 of the fan
headers are backward compatible with the
traditional 3-pin fans. See the table on the
right for pin definitions. Note: The onboard
fan speeds are controlled by Thermal Man-
agement via BIOS Hardware Monitoring in
the Advanced Setting. (The default setting
is Disabled.) Please use all 3-pin fans or
all 4-pin fans on the motherboard.
Fan Header
Pin Definitions (Fan1-6)
Pin# Definition
1
2
3
4
Ground
+12V
Tachometer
PWR Modulation
Chassis Intrusion
Chassis Intrusion
Pin Definitions (JL1)
A Chassis Intrusion header is located at
JL1 on the motherboard. Attach an appro-
priate cable from the chassis to inform you
of a chassis intrusion when the chassis is
opened.
Pin# Definition
1
2
Intrusion Input
Ground
JPWF1
CPU1 VRM OH LED
LED5
A. Fan 1
SMB_PS
JAR
A
24-Pin PWR
8-Pin PWR
B. Fan 2
C. Fan 3
DIMM2A
CPU1
D. Fan 4
DIMM1A
DIMM2B
DIMM1B
E. Fan 5
DIMM2C
DIMM1C
F. Fan 6
G. Chassis Intrusion
X7DCL-3/i
CPU2
JPL2
LAN
CTRL
Intel
5100
E
North Bridge
F
I-Btton
Fan
Fan
2
3
LED6
LAN
CPU2 VRM OH LED
B
C
JP2
JP1
CTRL
Slot6 PCI-E x8
SP1
Buzzer
Intel
Slot5 PCI-E x8
ICH9R
PWR LED
LED3
South Bridge
Slot4 PCI-E x4(in x8 slot)
Slot3 PCI 33MHz
VGA
CTRL
JBT1
LED1
BIOS
JPG1
Battery
LSI
SAS
CTRL
ITE
SAS-GPIO1
SAS-GPIO0
Slot2 PCI 33MHz
JWOL1
S
I/O
JWD1
CTRL
JPA2
LED4
Slot1 PCI 33MHz
SIMLC
G
USB4/5
BPI
System Status LED
COM2
USB2/3
JL1
2
D
C
Fan
4
2-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
ATX PS/2 Keyboard and
PS/2 Mouse Ports
PS/2 Keyboard and
Mouse Port Pin
Definitions
Pin# Definition
The ATX PS/2 keyboard and the PS/2
mouse are located at JKM1. See the
table on the right for pin definitions.
(The mouse port is above the key-
board port.) See the table on the right
for pin definitions.
1
2
3
4
5
6
Data
NC
Ground
VCC
Clock
NC
Serial Port Pin Definitions
(COM1/COM2)
Serial Ports
Pin #
Definition
CD
Pin #
Definition
DSR
1
2
3
4
5
6
7
8
9
COM1 is a connector located on the
IO Backpanel, and COM2 is a header
located at JCOM2. See the table on
the right for pin definitions.
RD
RTS
CTS
RI
TD
DTR
Ground
10
NC
(Pin 10 is available on COM2
only. NC: No Connection.)
JPWF1
CPU1 VRM OH LED
LED5
SMB_PS
JAR
24-Pin PWR
8-Pin PWR
A
DIMM2A
CPU1
A. Keyboard/Mouse
B. COM1
DIMM1A
DIMM2B
DIMM1B
B
DIMM2C
DIMM1C
C. COM2
X7DCL-3/i
CPU2
JPL2
LAN
CTRL
Intel
5100
North Bridge
I-Button
Fan
Fan
2
3
LED6
LAN
CTRL
CPU2 VRM OH LED
JP2
JP1
Slot6 PCI-E x8
SP1
Buzzer
Intel
Slot5 PCI-E x8
ICH9R
PWR LED
LED3
South Bridge
Slot4 PCI-E x4(in x8 slot)
Slot3 PCI 33MHz
VGA
CTRL
JBT1
LED1
BIOS
JPG1
Battery
LSI
SAS
CTRL
ITE
SAS-GPIO1
SAS-GPIO0
Slot2 PCI 33MHz
JWOL1
S
I/O
JWD1
CTRL
JPA2
LED4
C
Slot1 PCI 33MHz
SIMLC
USB4/5
BPI
System Status LED
COM2
USB2/3
JL1
2
C
Fan
4
2-17
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
Wake-On-Ring
The Wake-On-Ring header is lo-
cated at JWOR1. This feature allows
your computer to receive and be
"awakened" by an incoming call to
the modem when the system is in
the suspend state. See the table on
the right for pin definitions. You must
have a Wake-On-Ring card and cable
to use this feature.
Wake-On-Ring
Pin Definitions
Pin# Definition
1
2
Ground
Wake-up
Wake-On-LAN
Wake-On-LAN
Pin Definitions
The Wake-On-LAN header is located
at JWOL1 on the motherboard. See
the table on the right for pin defini-
tions. (You must have a LAN card
with a Wake-On-LAN connector, and
cable to use this feature.)
Pin# Definition
1
2
3
+5V Standby
Ground
Wake-up
JPWF1
CPU1 VRM OH LED
LED5
A. WOR
B. WOL
SMB_PS
JAR
24-Pin PWR
8-Pin PWR
DIMM2A
CPU1
DIMM1A
DIMM2B
DIMM1B
DIMM2C
DIMM1C
X7DCL-3/i
CPU2
JPL2
LAN
CTRL
Intel
5100
North Bridge
I-Button
Fan
Fan
2
3
LED6
LAN
CTRL
CPU2 VRM OH LED
JP2
JP1
Slot6 PCI-E x8
SP1
Buzzer
Intel
Slot5 PCI-E x8
ICH9R
PWR LED
LED3
South Bridge
Slot4 PCI-E x4(in x8 slot)
Slot3 PCI 33MHz
VGA
CTRL
JBT1
LED1
BIOS
JPG1
Battery
LSI
SAS
CTRL
ITE
SAS-GPIO1
SAS-GPIO0
Slot2 PCI 33MHz
JWOL1
S
I/O
JWD1
CTRL
B
JPA2
A
LED4
Slot1 PCI 33MHz
USB4/5
BPI
System Status LED
COM2
USB2/3
JL1
2
SIMLC
C
Fan
4
2-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
GLAN 1/2 (Giga-bit Ethernet
Ports)
Two G-bit Ethernet ports are located
at JLAN1 and JLAN2 on the I/O
backplane. These ports accept RJ45
type cables.
GLAN2
GLAN1
Power LED/Speaker
On the JD1 header, pins 1-3 are for
a power LED, and pins 4-7 are for
the speaker. See the table on the
right for speaker pin definitions. Note:
The speaker connector pins are for
use with an external speaker. If you
wish to use the onboard speaker, you
should close pins 6-7 with a jumper.
Speaker Connector
Pin Setting Definition
Pins 6-7 Internal Speaker
Pins 4-7 External Speaker
A. GLAN1
JPWF1
CPU1 VRM OH LED
LED5
SMB_PS
JAR
24-Pin PWR
8-Pin PWR
B. GLAN2
C. PWR LED/Speaker
DIMM2A
CPU1
DIMM1A
DIMM2B
DIMM1B
DIMM2C
DIMM1C
X7DCL-3/i
A
JPL2
CPU2
LAN
B
CTRL
Intel
5100
North Bridge
I-Button
Fan
Fan
2
3
LED6
LAN
CTRL
CPU2 VRM OH LED
JP2
JP1
Slot6 PCI-E x8
SP1
Buzzer
Intel
Slot5 PCI-E x8
ICH9R
PWR LED
LED3
South Bridge
Slot4 PCI-E x4(in x8 slot)
Slot3 PCI 33MHz
VGA
CTRL
JBT1
LED1
BIOS
JPG1
Battery
LSI
SAS
CTRL
ITE
SAS-GPIO1
SAS-GPIO0
Slot2 PCI 33MHz
JWOL1
S
I/O
JWD1
CTRL
C
JPA2
LED4
Slot1 PCI 33MHz
SIMLC
USB4/5
BPI
System Status LED
COM2
USB2/3
JL1
2
C
Fan
4
2-19
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
Alarm Reset
If three power supplies are installed,
the system will notify you when any of
the three power modules fails. Con-
nect JAR1 to a micro-switch to turn
off the alarm that is activated when a
power module fails. See the table on
the right for pin definitions.
Alarm Reset
Pin Definitions
Pin Setting Definition
Pin 1
Pin 2
Ground
+5V
PWR Supply Failure/PWR
Fault Detect
The system can notify you in the
event of a power supply failure. This
feature is available when three power
supply units are installed in the chas-
sis with one acting as a backup. If you
only have one or two power supply
units installed, you should disable
this (the default setting) with JPWF1
to prevent false alarms.
PWR Supply PWR Fault
Connector
Jumper Setting Definition
On
Off
Enabled
Disabled (Default)
B
JPWF1
CPU1 VRM OH LED
LED5
A. Alarm Reset
B. PWR Fault
SMB_PS
JAR
24-Pin PWR
8-Pin PWR
A
DIMM2A
CPU1
DIMM1A
DIMM2B
DIMM1B
DIMM2C
DIMM1C
X7DCL-3/i
CPU2
JPL2
LAN
CTRL
Intel
5100
North Bridge
I-Button
Fan
Fan
2
3
LED6
LAN
CTRL
CPU2 VRM OH LED
JP2
JP1
Slot6 PCI-E x8
SP1
Buzzer
Intel
Slot5 PCI-E x8
ICH9R
PWR LED
LED3
South Bridge
Slot4 PCI-E x4(in x8 slot)
Slot3 PCI 33MHz
VGA
CTRL
JBT1
LED1
BIOS
JPG1
Battery
LSI
SAS
CTRL
ITE
SAS-GPIO1
SAS-GPIO0
Slot2 PCI 33MHz
JWOL1
S
I/O
JWD1
CTRL
JPA2
LED4
Slot1 PCI 33MHz
SIMLC
USB4/5
BPI
System Status LED
COM2
USB2/3
JL1
2
C
Fan
4
2-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
VGA Connector
A VGA connector (JVGA) is located next
to the COM1 port on the IO backplane.
Refer to the board layout below for the
location.
GPIO Headers
Four GPIO (Serial Links General Purpose
Input/Output) headers are located at J7,
J8, J9, J10 on the motherboard. These
headers are used to communicate with
the Seriel-Links System Monitoring chip
on the backplane. J7 and J8 are used to
monitor SATA activities, J9 and J10 are
used to monitor SAS connections. See
the table on the right for pin definitions.
Refer to the board layout below for the
locations of the headers.
Serial-Links GPIO
Pin Definitions
Pin# Definition
Pin
2
Definition
NC
1
3
NC
Ground
4
DATA Out
5
7
Load
6
8
Ground
NC
Clock
Note: NC= No Connections
(J9, J10: X7DCL-3 Only.)
JPWF1
CPU1 VRM OH LED
LED5
A. VGA
SMB_PS
JAR
24-Pin PWR
8-Pin PWR
B. J7: SATA_GPIO#0
C. J8: SATA_GPIO#1
D. J9: SAS_GPIO#0
E. J10: SAS_GPIO#1
DIMM2A
CPU1
DIMM1A
DIMM2B
DIMM1B
DIMM2C
DIMM1C
A
X7DCL-3/i
CPU2
JPL2
LAN
CTRL
Intel
5100
North Bridge
I-Button
Fan
Fan
2
3
LED6
LAN
CTRL
CPU2 VRM OH LED
JP2
JP1
Slot6 PCI-E x8
SP1
Buzzer
Intel
Slot5 PCI-E x8
B
C
ICH9R
PWR LED
LED3
South Bridge
JBT1
Slot4 PCI-E x4(in x8 slot)
Slot3 PCI 33MHz
VGA
CTRL
LED1
BIOS
JPG1
Battery
LSI
E
SAS-GPIO1
SAS-GPIO0
JPA2
SAS
CTRL
ITE
Slot2 PCI 33MHz
JWOL1
S
I/O
JWD1
CTRL
LED4
Slot1 PCI 33MHz
SIMLC
D
USB4/5
System Status LED
COM2
USB2/3
JL1
2
BPI
C
Fan
4
2-21
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
Power SMB (I2C) Connector
PWR SMB
Pin Definitions
Power SMB (I2C) Connector (JPIC1)
monitors the status of the power supply,
fan and system temperature. See the
table on the right for pin definitions.
Pin# Definition
1
2
Clock
Data
3
4
5
PWR Fail
Ground
+3.3V
BP PWR SMB
Pin Definitions
BP PWR SMB (I2C) Connector
Pin# Definition
Backplane Power SMB (I2C) Connector
(J5) monitors power supply of backplane
IO connectors. See the table on the right
for pin definitions.
1
2
SMB_DAT_ICH_EXT
Ground
3
5
SMB_CLK_ICH_EXT
No Connection
JPWF1
CPU1 VRM OH LED
LED5
A. PWR SMB
B. Backplane PWR SMB
SMB_PS
JAR
24-Pin PWR
8-Pin PWR
A
DIMM2A
CPU1
DIMM1A
DIMM2B
DIMM1B
DIMM2C
DIMM1C
X7DCL-3/i
CPU2
JPL2
LAN
CTRL
Intel
5100
North Bridge
I-Button
Fan
Fan
2
3
LED6
LAN
CTRL
CPU2 VRM OH LED
JP2
JP1
Slot6 PCI-E x8
SP1
Buzzer
Intel
Slot5 PCI-E x8
ICH9R
PWR LED
LED3
South Bridge
Slot4 PCI-E x4(in x8 slot)
Slot3 PCI 33MHz
VGA
CTRL
JBT1
LED1
BIOS
JPG1
Battery
LSI
SAS
CTRL
ITE
SAS-GPIO1
SAS-GPIO0
Slot2 PCI 33MHz
JWOL1
S
I/O
JWD1
CTRL
JPA2
LED4
Slot1 PCI 33MHz
SIMLC
USB4/5
BPI
System Status LED
COM2
/3
JL1
2
B
C
Fan
4
2-22
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
Keylock
Keylock
Pin Definitions
The keyboard lock connection is desig-
nated JKEY1. Utilizing this header allows
you to inhibit any actions made on the
keyboard, effectively "locking" it.
Pin# Definition
1
2
Ground
Keylock R-N
JPWF1
CPU1 VRM OH LED
LED5
A. Keylock
SMB_PS
JAR
24-Pin PWR
8-Pin PWR
DIMM2A
CPU1
DIMM1A
DIMM2B
DIMM1B
DIMM2C
DIMM1C
X7DCL-3/i
CPU2
JPL2
LAN
CTRL
Intel
5100
North Bridge
I-Button
Fan
Fan
2
3
LED6
LAN
CTRL
CPU2 VRM OH LED
JP2
JP1
Slot6 PCI-E x8
SP1
Buzzer
Intel
Slot5 PCI-E x8
ICH9R
PWR LED
LED3
South Bridge
Slot4 PCI-E x4(in x8 slot)
Slot3 PCI 33MHz
VGA
CTRL
JBT1
LED1
BIOS
JPG1
Battery
LSI
SAS
CTRL
ITE
SAS-GPIO1
SAS-GPIO0
Slot2 PCI 33MHz
JWOL1
S
I/O
JWD1
CTRL
A
JPA2
LED4
Slot1 PCI 33MHz
SIMLC
USB4/5
BPI
System Status LED
COM2
USB2/3
JL1
2
C
Fan
4
2-23
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
2-6
Jumper Settings
Explanation of
Jumpers
3
2
1
Connector
Pins
To modify the operation of the
motherboard, jumpers can be used
to choose between optional settings.
Jumpers create shor ts between two pins
to change the function of the connector.
Pin 1 is identified with a square solder
pad on the printed circuit board. See
themotherboardlayoutpagesforjumper
locations.
Jumper
Cap
3
2
1
Setting
Pin 1-2 short
Note: On two pin jumpers, "Closed"
means the jumper is on and "Open"
means the jumper is off the pins.
GLAN Enable/Disable
GLAN Enable
Jumper Settings
JPL1/JPL2 enable or disable GLAN
Port1/GLAN Port2 on the mother-
board. See the table on the right for
jumper settings. The default setting is
Enabled.
Pin# Definition
1-2
2-3
Enabled (default)
Disabled
JPWF1
CPU1 VRM OH LED
LED5
A. GLAN Port1 Enable
B. GLAN Port2 Enable
SMB_PS
JAR
24-Pin PWR
8-Pin PWR
DIMM2A
CPU1
DIMM1A
DIMM2B
DIMM1B
DIMM2C
DIMM1C
X7DCL-3/i
B
CPU2
JPL2
LAN
CTRL
Intel
5100
North Bridge
I-Button
Fan
Fan
2
3
LED6
LAN
CTRL
CPU2 VRM OH LED
JP2
JP1
Slot6 PCI-E x8
SP1
Buzzer
A
Intel
Slot5 PCI-E x8
ICH9R
PWR LED
LED3
South Bridge
Slot4 PCI-E x4(in x8 slot)
Slot3 PCI 33MHz
VGA
CTRL
JBT1
LED1
BIOS
JPG1
Battery
LSI
SAS
CTRL
ITE
SAS-GPIO1
SAS-GPIO0
Slot2 PCI 33MHz
JWOL1
S
I/O
JWD1
CTRL
JPA2
LED4
Slot1 PCI 33MHz
SIMLC
USB4/5
BPI
System Status LED
COM2
USB2/3
JL1
2
C
Fan
4
2-24
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
CMOS Clear
JBT1 is used to clear CMOS. Instead of pins, this "jumper" consists of contact
pads to prevent the accidental clearing of CMOS. To clear CMOS, use a metal
object such as a small screwdriver to touch both pads at the same time to short
the connection. Always remove the AC power cord from the system before clear-
ing CMOS.
Note: For an ATX power supply, you must completely shut down the system,
remove the AC power cord and then short JBT1 to clear CMOS.
Watch Dog Enable/Disable
Watch Dog
Jumper Settings
Watch Dog is a system monitor that can reboot
Jumper Setting Definition
the system when a software application hangs.
Close pins 1-2 to reset the system if an applica-
tion hangs. Close pins 2-3 to generate a non-
maskable interrupt signal for the application that
hangs. See the table on the right for jumper set-
tings. Watch Dog must also be enabled in the
BIOS.
Pins 1-2
Reset
(default)
Pins 2-3
Open
NMI
Disabled
JPWF1
CPU1 VRM OH LED
LED5
A. Clear CMOS
SMB_PS
JAR
24-Pin PWR
8-Pin PWR
B. Watch Dog Enable
DIMM2A
CPU1
DIMM1A
DIMM2B
DIMM1B
DIMM2C
DIMM1C
X7DCL-3/i
CPU2
JPL2
LAN
CTRL
Intel
5100
North Bridge
I-Button
Fan
Fan
2
3
LED6
LAN
CTRL
CPU2 VRM OH LED
JP2
JP1
Slot6 PCI-E x8
SP1
Buzzer
Intel
Slot5 PCI-E x8
ICH9R
PWR LED
LED3
South Bridge
Slot4 PCI-E x4(in x8 slot)
Slot3 PCI 33MHz
VGA
CTRL
JBT1
A
LED1
BIOS
JPG1
Battery
LSI
SAS
CTRL
ITE
SAS-GPIO1
SAS-GPIO0
Slot2 PCI 33MHz
JWOL1
S
I/O
JWD1
CTRL
B
JPA2
LED4
Slot1 PCI 33MHz
SIMLC
USB4/5
BPI
System Status LED
COM2
USB2/3
JL1
2
C
Fan
4
2-25
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
VGA Enable/Disable
VGA Enable/Disable
Jumper Settings
JPG1 allows you to enable or disable the
VGA port. The default position is on pins
1 and 2 to enable VGA. See the table on
the right for jumper settings.
Both Jumpers Definition
Pins 1-2
Pins 2-3
Enabled (Default)
Disabled
I2C Bus to PCI/PCI-Exp. Slots
Jumpers JPI2C1/JPI2C2 allow you to
connect the System Management Bus
(I2C) to PCI/PCI-Exp. slots. The default
setting is Open to disable the connec-
tion. See the table on the right for jumper
settings.
I2C to PCI/PCI-Exp. Slots
Jumper Settings
Jumper Setting Definition
Closed
Open
Enabled
Disabled (Default)
JPWF1
CPU1 VRM OH LED
LED5
A. VGA Enabled
SMB_PS
JAR
B. JPI2C1
C. JPI2C2
24-Pin PWR
8-Pin PWR
DIMM2A
CPU1
DIMM1A
DIMM2B
DIMM1B
DIMM2C
DIMM1C
X7DCL-3/i
CPU2
JPL2
LAN
CTRL
Intel
5100
North Bridge
I-Button
Fan
Fan
2
3
LED6
LAN
CPU2 VRM OH LED
JP2
JP1
CTRL
Slot6 PCI-E x8
SP1
Buzzer
Intel
Slot5 PCI-E x8
ICH9R
PWR LED
LED3
B
South Bridge
C
Slot4 PCI-E x4(in x8 slot)
VGA
CTRL
JBT1
LED1
BIOS
JPG1
Slot3 PCI 33MHz
A
Battery
LSI
SAS
CTRL
ITE
SAS-GPIO1
SAS-GPIO0
Slot2 PCI 33MHz
JWOL1
S
I/O
JWD1
CTRL
JPA2
LED4
Slot1 PCI 33MHz
SIMLC
USB4/5
BPI
System Status LED
COM2
USB2/3
JL1
2
C
Fan
4
2-26
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
SAS Enable/Disable
JPA1 allows you to enable or disable
SAS Connectors. The default position is
on pins 1 and 2 to enable SAS. See the
table on the right for jumper settings.
SAS Enable/Disable
Jumper Settings
Jumper Settings Definition
Pins 1-2
Pins 2-3
Enabled (Default)
Disabled
(Note: This feature is available on the
X7DCL-3 only.)
Software RAID Enable
JPA2 allows you to select the SAS RAID
mode. You can use either Software
RAID or IT RAID. Close this jumper to
use Software RAID (Default). Set this
jumper to open to use the IT RAID mode.
Contact Tech. Support at Supermicro for
more information. See the table on the
right for jumper settings.
Software RAID
Jumper Settings
Jumper Settings
Close (Default)
Open (Note)
Definition
Software RAID Enabled
IT Mode Enabled
(Note: Also contact tech support at Super Micro for
further instructions.)
(Note: This feature is available on the
X7DCL-3 only.)
A. SAS Enabled
JPWF1
CPU1 VRM OH LED
LED5
SMB_PS
JAR
24-Pin PWR
8-Pin PWR
B. Software RAID Enable
DIMM2A
CPU1
DIMM1A
DIMM2B
DIMM1B
DIMM2C
DIMM1C
X7DCL-3/i
CPU2
JPL2
LAN
CTRL
Intel
5100
North Bridge
I-Button
Fan
Fan
2
3
LED6
LAN
CTRL
CPU2 VRM OH LED
JP2
JP1
Slot6 PCI-E x8
SP1
Buzzer
Intel
Slot5 PCI-E x8
ICH9R
PWR LED
LEAD
South Bridge
Slot4 PCI-E x4(in x8 slot)
Slot3 PCI 33MHz
VGA
CTRL
JBT1
LED1
BIOS
JPG1
Battery
LSI
SAS
CTRL
ITE
SAS-GPIO1
SAS-GPIO0
Slot2 PCI 33MHz
JWOL1
S
I/O
JWD1
CTRL
JPA2
B
LED4
Slot1 PCI 33MHz
SIMLC
USB4/5
2
System Status LED
COM2
USB2/3
JL1
BPI
C
Fan
4
2-27
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
Onboard LED Indicators
GLAN LEDs
Activity
LED
L i n k
LED
2-7
Rear View
(when viewing from the back of the chassis.)
There are two GLAN ports on the moth-
erboard. Each Gigabit Ethernet LAN port
has two LEDs. The yellow LED indicates
activity, while the power LED may be
green, orange or off to indicate the speed
of the connection. See the tables at right
for more information.
GLAN Activity Indicator
Settings
Color
Status
Definition
Yellow
Flashing
LAN Active
GLAN Link Indicator
Settings
LED Color Definition
Off
No Connection or 10 Mbps
Green
Amber
100 Mbps
1 Gbps
Onboard Power LED (LED3)
An Onboard Power LED is located at
LED3 on the motherboard. When this
LED is lit, the system is on. Be sure
to turn off the system and unplug the
power cord before removing or installing
components. See the layout below for the
LED location.
JPWF1
CPU1 VRM OH LED
LED5
A. GLAN Port1 LEDs
B. GLAN Port2 LEDs
C. Onboard PWR LED
SMB_PS
JAR
24-Pin PWR
8-Pin PWR
DIMM2A
CPU1
DIMM1A
DIMM2B
DIMM1B
DIMM2C
DIMM1C
X7DCL-3/i
A
JPL2
CPU2
LAN
B
CTRL
Intel
5100
North Bridge
I-Button
Fan
Fan
2
3
LED6
LAN
CTRL
CPU2 VRM OH LED
JP2
JP1
Slot6 PCI-E x8
SP1
Buzzer
Intel
Slot5 PCI-E x8
C
ICH9R
PWR LED
LED3
South Bridge
Slot4 PCI-E x4(in x8 slot)
Slot3 PCI 33MHz
VGA
CTRL
JBT1
LED1
BIOS
JPG1
Battery
LSI
SAS
CTRL
ITE
SAS-GPIO1
SAS-GPIO0
Slot2 PCI 33MHz
JWOL1
S
I/O
JWD1
CTRL
JPA2
LED4
Slot1 PCI 33MHz
SIMLC
USB4/5
BPI
System Status LED
COM2
USB2/3
JL1
2
C
Fan
4
2-28
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
System Status LED (LED4)
Status LED Indicator
Settings
A Status LED Indicator is located at
LED4 on the motherboard. This LED dis-
plays different colors to show the status
of the system. Refer to the table on the
right for system status. See the layout
below for the LED location.
LED Color Definition
Green
Red
Power On, system: normal
PWR on, PWR problem(s)
occur(s) or the 3rd PWR
not properly installed
Yellow
System Off, AC PWR:
connected
CPU_VRM Overheating LED
Indicators (LED5/LED6)
CPU_VRM Overheat LED Indicator
Settings
Two CPU_VRM Overheat LEDs are locat-
ed at LED5 and LED 6 on the mother board.
These LEDs provide indications for
CPU_VRM Overheating. Refer to the
table on the right for LED5 and LED6
settings. See the layout below for the
LED locations.
LED#
Description
LED5: On
LED6: On
CPU1_VRM Overheating
CPU2_VRM Overheating
JPWF1
CPU1 VRM OH LED
LED5
A. LED4: System Status LED
B. LED5: CPU1_VRM OH LED
C. LED6: CPU2_VRM OH LED
SMB_PS
JAR
B
24-Pin PWR
8-Pin PWR
DIMM2A
CPU1
DIMM1A
DIMM2B
DIMM1B
DIMM2C
DIMM1C
X7DCL-3/i
CPU2
JPL2
LAN
CTRL
Intel
5100
North Bridge
I-Button
Fan
Fan
2
3
LED6
LAN
CTRL
CPU2 VRM OH LED
JP2
JP1
C
Slot6 PCI-E x8
SP1
Buzzer
Intel
Slot5 PCI-E x8
ICH9R
PWR LED
LED3
South Bridge
Slot4 PCI-E x4(in x8 slot)
Slot3 PCI 33MHz
VGA
CTRL
JBT1
LED1
BIOS
JPG1
Battery
LSI
SAS
CTRL
ITE
SAS-GPIO1
SAS-GPIO0
Slot2 PCI 33MHz
JWOL1
S
I/O
JWD1
CTRL
A
JPA2
LED4
Slot1 PCI 33MHz
SIMLC
USB4/5
BPI
System Status LED
COM2
USB2/3
JL1
2
C
Fan
4
2-29
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
SAS LED Indicator (LED1)
A SAS LED is located at LED1 on the
motherboard.ThisLEDindicatesthestatus
of SAS connections. Refer to the table on
the right for LED1 settings. See the layout
below for the LED location.
SAS LED Indicator
Settings
LED#
Description
LED1: On
LED1: Off
SAS: Active
SAS: Not Active
(Available on the X7DCL-3 only)
JPWF1
CPU1 VRM OH LED
LED5
A. LED1: SAS LED
SMB_PS
JAR
24-Pin PWR
8-Pin PWR
DIMM2A
CPU1
DIMM1A
DIMM2B
DIMM1B
DIMM2C
DIMM1C
X7DCL-3/i
CPU2
JPL2
LAN
CTRL
Intel
5100
North Bridge
I-Button
Fan
Fan
2
3
LED6
LAN
CTRL
CPU2 VRM OH LED
JP2
JP1
Slot6 PCI-E x8
SP1
Buzzer
Intel
Slot5 PCI-E x8
ICH9R
PWR LED
LED3
South Bridge
Slot4 PCI-E x4(in x8 slot)
Slot3 PCI 33MHz
VGA
A
CTRL
JBT1
LED1
BIOS
JPG1
Battery
LSI
SAS
CTRL
ITE
SAS-GPIO1
SAS-GPIO0
Slot2 PCI 33MHz
JWOL1
S
I/O
JWD1
CTRL
JPA2
LED4
Slot1 PCI 33MHz
SIMLC
USB4/5
BPI
System Status LED
COM2
USB2/3
JL1
2
C
Fan
4
2-30
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
2-8
Floppy Drive, SIMLC IPMI and Hard Disk Drive
Connections
Note the following when connecting the floppy and hard disk drive cables:
•
•
The floppy disk drive cable has seven twisted wires.
A red mark on a wire typically designates the location of pin 1.
Floppy Drive Connector
Pin Definitions (Floppy)
Floppy Connector
Pin# Definition
Pin #
2
Definition
The floppy connector is located at
JFDD1. See the table below for pin
definitions.
1
Ground
Ground
Key
FDHDIN
3
4
Reserved
FDEDIN
5
6
7
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
8
Index
9
10
12
14
16
18
20
22
24
26
28
30
32
34
Motor Enable
Drive Select B
Drive Select B
Motor Enable
DIR
11
13
15
17
19
21
23
25
27
29
31
33
STEP
Write Data
Write Gate
Track 00
Write Protect
Read Data
Side 1 Select
Diskette
JPWF1
CPU1 VRM OH LED
LED5
SMB_PS
JAR
24-Pin PWR
8-Pin PWR
A. Floppy Disk Drive
DIMM2A
CPU1
DIMM1A
DIMM2B
DIMM1B
DIMM2C
DIMM1C
X7DCL-3/i
CPU2
JPL2
LAN
CTRL
Intel 5100
North Bridge
I-Button
Fan
Fan
2
3
LED6
LAN
CTRL
CPU2 VRM OH LED
JP2
JP1
Slot6 PCI-E x8
SP1
Buzzer
Intel
Slot5 PCI-E x8
ICH9R
PWR LED
LED3
South Bridge
Slot4 PCI-E x4(in x8 slot)
Slot3 PCI 33MHz
A
VGA
CTRL
JBT1
LED1
BIOS
JPG1
Battery
LSI
SAS
CTRL
ITE
SAS-GPIO1
SAS-GPIO0
Slot2 PCI 33MHz
JWOL1
S
I/O
JWD1
CTRL
JPA2
LED4
Slot1 PCI 33MHz
SIMLC
USB4/5
BPI
System Status LED
COM2
USB2/3
JL1
2
C
Fan
4
2-31
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
IDE Connector
IDE Drive Connector
Pin Definitions
An IDE Connector is located at JIDE1
on the motherboard. This motherboard
uses the ITE IT8213F Controller. An
IDE Driver is required for the IDE drive
to function properly. See the table on
the right for pin definitions.
Pin# Definition
Pin #
2
Definition
1
Reset IDE
Host Data 7
Host Data 6
Host Data 5
Host Data 4
Host Data 3
Host Data 2
Host Data 1
Host Data 0
Ground
Ground
3
4
Host Data 8
Host Data 9
Host Data 10
Host Data 11
Host Data 12
Host Data 13
Host Data 14
Host Data 15
Key
5
6
7
8
9
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
DRQ3
Ground
I/O Write
I/O Read
IOCHRDY
DACK3
Ground
Ground
SIMLC IPMI Slot
BALE
A
Low Profile SIMLC IPMI Slot is
Ground
located on the motherboard. Refer
to the layout below for the IPMI Slot
location.
IRQ14
IOCS16
Addr1
Ground
Addr0
Addr2
Chip Select 0
Activity
Chip Select 1
Ground
A. IDE
JPWF1
CPU1 VRM OH LED
LED5
SMB_PS
JAR
24-Pin PWR
8-Pin PWR
B. SIMLC
DIMM2A
CPU1
DIMM1A
DIMM2B
DIMM1B
DIMM2C
DIMM1C
X7DCL-3/i
CPU2
JPL2
LAN
CTRL
Intel
5100
North Bridge
I-Button
Fan
Fan
2
3
LED6
LAN
CTRL
CPU2 VRM OH LED
JP2
JP1
Slot6 PCI-E x8
SP1
Buzzer
Intel
Slot5 PCI-E x8
ICH9R
PWR LED
LED3
South Bridge
Slot4 PCI-E x4(in x8 slot)
Slot3 PCI 33MHz
VGA
CTRL
JBT1
LED1
BIOS
JPG1
Battery
LSI
SAS
CTRL
ITE
A
SAS-GPIO1
SAS-GPIO0
Slot2 PCI 33MHz
JWOL1
S
I/O
JWD1
CTRL
JPA2
LED4
B
Slot1 PCI Hz
USB4/5
BPI
System Status LED
COM2
USB2/3
JL1
2
SIMLC
C
Fan
4
2-32
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Troubleshooting
Chapter 3
Troubleshooting
3-1
Troubleshooting Procedures
Use the following procedures to troubleshoot your system. If you have followed all
of the procedures below and still need assistance, refer to the ‘Technical Support
Procedures’ and/or ‘Returning Merchandise for Service’ section(s) in this chapter.
Note: Always disconnect the power cord before adding, changing or install-
ing any hardware components.
Before Power On
1. Make sure that there are no short circuits between the motherboard and the
chassis.
2. Disconnect all ribbon/wire cables from the motherboard, including those for
the keyboard and mouse. Remove all add-on cards.
3. Install a CPU in CPU Socket and connect the chassis speaker and the power
LED to the motherboard. (Make sure that the CPU is properly seated. Be sure
to check all jumper settings as well.)
No Power
1. Make sure that there are no short circuits between the motherboard and the
chassis.
2. Make sure that all jumpers are set to their default positions.
3. Make sure that the 115V/230V switch on the power supply is properly set.
4. Turn the power switch on and off to test the system. The battery on your
motherboard may be old. Check to verify that it still supplies ~3VDC. If it
does not, replace it with a new one.
No Video
1. If the power is on but you have no video, remove all the add-on cards and
cables.
2. Use the speaker to determine if any beep codes exist. Refer to the Appendix
for details on beep codes.
Losing the System’s Setup Configuration
1. Make sure that you are using a high quality power supply. A poor quality
power supply may cause the system to lose the CMOS setup information.
Refer to Section 1-6 for details on recommended power supplies.
2. The battery on your motherboard may be old. Check to verify that it still
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
supplies ~3VDC. If it does not, replace it with a new one.
3. If the above steps do not fix the Setup Configuration problem, contact your
vendor for repairs.
NOTE
If you are a system integrator, VAR or OEM, a POST diagnostics
card is recommended. For I/O port 80h codes, refer to App. B.
Memory Errors
1. Make sure the DIMM modules are properly and fully installed. Check if
DIMMs of different speeds or types have been installed. Also make sure that
the BIOS setup is configured for the fastest speed of RAM used.
2. It is recommended to use the same RAM speed for all DIMMs in the system.
Make sure you are using the correct type of Single-Rank, Registered ECC
DDR2 667/533 SDRAM (recommended by the manufacturer.)
3. Check for bad DIMM modules or slots by swapping a single module between
four slots and noting the results. Make sure all memory modules are fully
seated in their slots. As an interleaved memory scheme is used, you must
install two modules at a time, beginning with DIMM 1A, then DIMM 2A, and
so on (see Section 2-3). Check the position of the 115V/230V switch on the
power supply.
3-2
Technical Support Procedures
Before contacting Technical Support, please take the following steps. Also, note
that as a motherboard manufacturer, Super Micro does not sell directly to end-us-
ers, so it is best to first check with your distributor or reseller for troubleshooting
services. They should know of any possible problem(s) with the specific system
configuration that was sold to you.
1. Please go through the ‘Troubleshooting Procedures’ and 'Frequently Asked
Question' (FAQ) sections in this chapter or see the FAQs on our web site (http://
com/support/bios/.
3. If you still cannot resolve the problem, include the following information when
contacting Super Micro for technical support:
•
•
Motherboard model and PCB revision number
BIOS release date/version (this can be seen on the initial display when your
system first boots up)
3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Troubleshooting
•
•
System configuration
supermicro.com/support/contact.cfm/.
•
Distributors: For immediate assistance, please have your account number
ready when placing a call to our technical support department. We can be
reached by e-mail at [email protected] or by fax at: (408) 503-8000,
option 2.
3-3
Frequently Asked Questions
Question: What are the various types of memory that my motherboard can
support?
Answer: The X7DCL-3/X7DCL-i has six 240-pin DIMM slots that support Single-
Rank, Registered ECC DDR2 667/533 SDRAM modules. It is strongly recom-
mended that you do not mix memory modules of different speeds and sizes. (See
Chapter 2 for detailed Information.)
Question: Why does Microsoft Windows XP (SP2) and Windows Vista show
less memory than what is physically installed?
Answer: Microsoft implemented a design change in Windows XP with Service
Pack 2 (SP2) and Windows Vista. This change is specific to the Physical Address
Extension (PAE) mode behavior which improves driver compatibility. For more in-
formation, please read the following article at Microsoft’s Knowledge Base website
Question: How do I update my BIOS?
Answer: It is recommended that you do not upgrade your BIOS if you are not
experiencing any problems with your system. Updated BIOS files are located on
warning message and the information on how to update your BIOS on our web
site. Select your motherboard model and download the BIOS file to your computer.
Also, check the current BIOS revision and make sure that it is newer than your
BIOS before downloading. You can choose from the zip file and the .exe file. If
you choose the zip BIOS file, please unzip the BIOS file onto a bootable device or
a USB pen. Run the batch file using the format flash.bat filename.rom from your
bootable device or USB pen to flash the BIOS. Then, your system will automati-
cally reboot. If you choose the .exe file, please run the .exe file under Windows to
create the BIOS flash floppy disk. Insert the floppy disk into the system you wish
to flash the BIOS. Then, bootup the system to the floppy disk. The BIOS utility will
automatically flash the BIOS without any prompts. Please note that this process
may take a few minutes to complete. Do not be concerned if the screen is paused
for a few minutes.
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
(Warning: Do not shut down or reset the system while updating BIOS to
prevent possible system boot failure!)
Question: What's on the CD that came with my motherboard?
Answer: The supplied compact disc has quite a few drivers and programs that will
greatly enhance your system. We recommend that you review the CD and install
the applications you need. Applications on the CD include chipset drivers for the
Windows OS, and security and audio drivers.
3-4
Returning Merchandise for Service
A receipt or copy of your invoice marked with the date of purchase is required
before any warranty service will be rendered. You can obtain service by calling
your vendor for a Returned Merchandise Authorization (RMA) number. When
returning to the manufacturer, the RMA number should be prominently displayed
on the outside of the shipping carton, and mailed prepaid or hand-carried. Ship-
ping and handling charges will be applied for all orders that must be mailed when
service is complete.
This warranty only covers normal consumer use and does not cover damage in-
curred in shipping or from failure due to the alternation, misuse, abuse or improper
maintenance of products.
During the warranty period, contact your distributor first for any product prob-
lems.
supermicro.com/support/rma/).
3-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: BIOS
Chapter 4
BIOS
4-1
Introduction
This chapter describes the Phoenix BIOS™ Setup utility for the X7DCL-3/X7DCL-i.
Phoenix ROM BIOS is stored in a flash chip and can be easily upgraded using a
floppy disk-based program.
Note: Due to periodic changes to the BIOS, some settings may have been added
or deleted and might not yet be recorded in this manual. Please refer to the Manual
changes to the BIOS that may not be reflected in this manual.
System BIOS
BIOS is the Basic Input Output System used in all IBM® PC, XT™, AT®, and PS/2®
compatible computers. Phoenix BIOS stores the system parameters, types of disk
drives, video displays, etc. in the CMOS. CMOS memory requires very little electrical
power. When the computer is turned off, a backup battery provides power to the
CMOS Logic, enabling it to retain system parameters. Each time the computer is
powered on, the computer is configured with the values stored in the CMOS Logic
by the system BIOS, which gains control at boot up.
How To Change the Configuration Data
The CMOS information that determines the system parameters may be changed by
entering the BIOS Setup utility. This Setup utility can be accessed by pressing the
<Delete> key at the appropriate time during system boot. (See below.)
Starting the Setup Utility
Normally, the only visible POST (Power On Self Test) routine is the memory test. As
the memory is being tested, press the <Delete> key to enter the main menu of the
BIOS Setup utility. From the main menu, you can access the other setup screens,
such as the Security and Power menus. Beginning with Section 4-3, detailed de-
scriptions are given for each parameter setting in the Setup utility.
Warning: Do not shut down or reset the system while updating BIOS
to prevent possible boot failure.
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
4-2
Running Setup
Default settings are in bold text unless otherwise noted.
The BIOS setup options described in this section are selected by choosing the ap-
propriate text from the main BIOS Setup screen. All displayed text is described in
this section, although the screen display is often all you need to understand how
to set the options.
When you first power on the computer, Phoenix BIOS™ is immediately activated.
While the BIOS is in control, the Setup program can be activated in one of two
ways:
1.
By pressing <Delete> immediately after turning the system on, or
2.
When the message shown below appears briefly at the bottom of the screen
during the POST (Power On Self-Test), press the <Delete> key to activate the main
Setup menu:
Press the <Delete> key to enter Setup
4-3
Main BIOS Setup
All main Setup options are described in this section. The main BIOS Setup screen
is displayed below.
Use the Up/Down arrow keys to move among the different settings in each menu.
Use the Left/Right arrow keys to change the options for each setting.
Press the <Esc> key to exit the CMOS Setup Menu. The next section describes in
detail how to navigate through the menus.
Items that use submenus are indicated with the icon. With the item highlighted,
press the <Enter> key to access the submenu.
4-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: BIOS
Main BIOS Setup Menu
Main Setup Features
System Time
To set the system date and time, key in the correct information in the appropriate
fields. Then press the <Enter> key to save the data.
System Date
Using the arrow keys, highlight the month, day and year fields, and enter the correct
data. Press the <Enter> key to save the data.
BIOS Date
This item displays the date when this version of BIOS was built.
Legacy Diskette A
This setting allows the user to set the type of floppy disk drive installed as diskette A.
The options are Disabled, 360Kb 5.25 in, 1.2MB 5.25 in, 720Kb 3.5 in, 1.44/1.25MB,
3.5 in and 2.88MB 3.5 in.
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
SATA Port 1 ~ SATA Port 6, Ext. Primary Master/Slave
These settings allow the user to set the parameters of the slots indicated above.
Press <Enter> to activate the following submenu screen for detailed options of
these items. Set the correct configurations accordingly. The items included in the
submenu are:
Type
This option allows the user to select the type of IDE hard drive. The option Auto
allows the BIOS to automatically configure the parameters of the HDD installed at
the connection. Enter a number between 1 to 39 to select a predetermined HDD
type. Select User to allow the user to enter the parameters of the HDD installed.
Select CDROM if a CDROM drive is installed. Select ATAPI if a removable disk
drive is installed.
Multi-Sector Transfers
This item allows the user to specify the number of sectors per block to be used
in multi-sector transfer. The options are Disabled, 4 Sectors, 8 Sectors, and
16 Sectors.
LBA Mode Control
This item determines whether the Phoenix BIOS will access the IDE Channel 0
Master Device via the LBA mode. The options are Enabled and Disabled.
4-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: BIOS
32 Bit I/O
This option allows the user to enable or disable the function of 32-bit data transfer.
The options are Enabled and Disabled.
Transfer Mode
This option allows the user to set the transfer mode. The options are Standard,
Fast PIO1, Fast PIO2, Fast PIO3, Fast PIO4, FPIO3/DMA1 and FPIO4/DMA2.
Ultra DMA Mode
This option allows the user to select Ultra DMA Mode. The options are Disabled,
Mode 0, Mode 1, Mode 2, Mode 3, Mode 4, and Mode 5.
Serial ATA
This setting allows the user to enable or disable the function of the Serial ATA. The
options are Disabled and Enabled.
Native Mode Operation
Select the native mode for ATA. The options are: Serial ATA and Auto.
SATA Controller Mode
SelectCompatibletoallowtheSATAandPATAdrivestobeautomatically-detected
and be placed in the Legacy Mode by the BIOS. Select Enhanced to allow the
SATA and PATA drives to be to be automatically-detected and be placed in the
Native IDE Mode. (Note: The Enhanced mode is supported by the Windows
2000 OS or a later version.)
When the SATA Controller Mode is set to "Enhanced", the following items
will display:
Serial ATA (SATA) RAID Enable
Select Enable to enable Serial ATA RAID Functions. (For the Windows OS
environment, use the RAID driver if this feature is set to Enabled. If this
item is set to Disabled, the item-SATA AHCI Enable will be available.) The
options are Enabled and Disabled.
ICH RAID Code Base
Select Intel to enable Intel's SATA RAID firmware to configure Intel's SATA
RAID settings. The options are Intel and Adaptec.
4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
SATA AHCI Enable
Select Enable to enable the function of Serial ATA Advanced Host Interface.
(Takecautionwhenusingthisfunction.Thisfeatureisforadvancedprogrammers
only.The options are Enabled and Disabled.)
System Memory
This display informs you how much system memory is detected by the BIOS.
Extended Memory
This display informs you how much extended memory is detected by the BIOS.
4-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: BIOS
4-4
Advanced Setup
Choose Advanced from the Phoenix BIOS Setup Utility main menu with the arrow
keys. You should see the following display.The items with a triangle beside them have
sub menus that can be accessed by highlighting the item and pressing <Enter>.
Boot Features
Access the submenu to make changes to the following settings.
QuickBoot Mode
If enabled, this feature will speed up the POST (Power On Self Test) routine by
skipping certain tests after the computer is turned on. The settings are Enabled
and Disabled. If Disabled, the POST routine will run at normal speed.
QuietBoot Mode
This setting allows you to Enable or Disable the graphic logo screen during boot-
up.
POST Errors
Set to Enabled to display POST Error Messages if an error occurs during bootup.
If set to Disabled, the system will continue to boot without displaying any error
message even when a boot error occurs.
ACPI Mode
Use the setting to determine if you want to employ ACPI (Advanced Configuration
and Power Interface) power management on your system. The options are Yes
and No.
4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
Power Button Behavior
If set to Instant-Off, the system will power off immediately as soon as the user
hits the power button. If set to 4-sec., the system will power off when the user
presses the power button for 4 seconds or longer. The options are instant-off and
4-sec override.
Resume On Modem Ring
Select On to “wake your system up” when an incoming call is received by your
modem. The options are On and Off.
Power Loss Control
This setting allows you to choose how the system will react when power returns
after an unexpected loss of power. The options are Stay Off, Power On, and
Last State.
Watch Dog
If enabled, this option will automatically reset the system if the system is not active
for more than 5 minutes. The options are Enabled and Disabled.
Summary Screen
This setting allows you to Enable or Disable the summary screen which displays
the system configuration during bootup.
Memory Cache
Cache System BIOS Area
This setting allows you to designate a reserve area in the system memory to be used
as a System BIOS buffer to allow the BIOS to write (cache) data into this reserved
memory area. Select Write Protect to enable this function, and this area will be
reserved for BIOS ROM access only. Select Uncached to disable this function and
make this area available for other devices.
Cache Video BIOS Area
This setting allows you to designate a reserve area in the system memory to be
used as a Video BIOS buffer to allow the BIOS to write (cache) data into this
reserved memory area. Select Write Protect to enable the function and this area
will be reserved for Video BIOS ROM access only. Select Uncached to disable this
function and make this area available for other devices.
4-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: BIOS
Cache Base 0-512K
If enabled, this feature will allow the data stored in the base memory area: block
0-512K to be cached (written) into a buffer, a storage area in the Static DROM
(SDROM) or to be written into L1, L2 cache inside the CPU to speed up CPU
operations. Select Uncached to disable this function. Select Write Through to allow
data to be cached into the buffer and written into the system memory at the
same time. Select Write Protect to prevent data from being written into the base
memory area of Block 0-512K. Select Write Back to allow the CPU to write data
back directly from the buffer without writing data to the System Memory for fast
CPU data processing and operation. The options are Uncached, Write Through,
Write Protect, and Write Back.
Cache Base 512K-640K
If enabled, this feature will allow the data stored in the memory area: 512K-640K
to be cached (written) into a buffer, a storage area in the Static DROM (SDROM)
or written into L1, L2, L3 cache inside the CPU to speed up CPU operations.
Select Uncached to disable this function. Select Write Through to allow data to
be cached into the buffer and written into the system memory at the same time.
Select Write Protect to prevent data from being written into the base memory
area of Block 512-640K. Select Write Back to allow the CPU to write data back
directly from the buffer without writing data to the System Memory for fast CPU
data processing and operation. The options are Uncached, Write Through, Write
Protect, and Write Back.
Cache Extended Memory
If enabled, this feature will allow the data stored in the extended memory area to
be cached (written) into a buffer, a storage area in the Static DROM (SDROM)
or written into L1, L2, L3 cache inside the CPU to speed up CPU operations.
Select Uncached to disable this function. Select Write Through to allow data
to be cached into the buffer and written into the system memory at the same
time. Select Write Protect to prevent data from being written into the extended
memory area above 1MB. Select Write Back to allow the CPU to write data back
directly from the buffer without writing data to the System Memory for fast CPU
data processing and operation. The options are Uncached, Write Through, Write
Protect, and Write Back.
Discrete MTRR Allocation
If enabled, MTRRs (-Memory Type Range Registers) are configured as distinct,
separate units and cannot be overlapped. If enabled, the user can achieve better
graphic effects when using a Linux graphic driver that requires the write-combining
configuration with 4GB or more memory. The options are Enabled and Disabled.
4-9
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
PCI Configuration
Access the submenu to make changes to the following settings for PCI devices.
Onboard GLAN-1/Onboard GLAN-2 (Gigabit- LAN) OPROM
Configure
Select Enabled to allow the system to boot from the GLAN-1 connection or the
GLAN-2 connection. The options are Disabled and Enabled.
Onboard Storage OPROM Configure
Select Enabled to allow the system to boot from the onboard storage device. The
options are Disabled and Enabled.
Reset Configuration Data
If set to Yes, this setting clears the Extended System Configuration Data- (ESCD)
area. The options are Yes and No.
Slot1 PCI 33MHz, Slot2 PCI 33MHz, Slot3 PCI 33MHz, Slot4 PCI-Exp.
x4, Slot5 PCI-Exp. x8, and Slot6 PCI-Exp. x8
Access the submenu for each of the settings above to make changes to the
following:
Option ROM Scan
When enabled, this setting will initialize the device expansion ROM. The options
are Enabled and Disabled.
Enable Master
This setting allows you to enable the selected device as the PCI bus master.
The options are Enabled and Disabled.
Latency Timer
This setting allows you to set the clock rate for Bus Master. A high-priority, high-
throughout device may benefit from a greater clock rate. The options are Default,
0020h, 0040h, 0060h, 0080h, 00A0h, 00C0h, and 00E0h. For Unix, Novell and
other Operating Systems, please select the option: other. If a drive fails after
the installation of a new software, you might want to change this setting and
try again. A different OS requires a different Bus Master clock rate.
Large Disk Access Mode
This setting determines the size of hard drive disk to be accessed by the system.
The options are DOS or Other (for Unix, Novelle NetWare and other operating
systems).
4-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: BIOS
Advanced Chipset Control
Access the submenu to make changes to the following settings.
Warning: Take Caution when changing the Advanced settings. An incorrect
setup, a very high DRAM frequency or an incorrect DRAM timing may cause
the system become unstable. When this occurs, reset the setting to the default
setting.
Accelerate MRC
If Enabled, the BIOS will skip MRC calculation if there aren't any changes in DIMM
population. The options are Enabled and Disabled.
Clock Spectrum Feature
If Enabled, the BIOS will monitor the level of Electromagnetic Interference caused
by the components and will attempt to decrease the interference whenever needed.
The options are Enabled and Disabled.
Crystal Beach Configure Enable
This feature cooperates with the Intel I/OAT (Acceleration Technology) to accelerate
the performance of TOE devices. (Note: A TOE device is a specialized, dedicated
processor that is installed on an add-on card or a network card to handle some or all
packet processing of this add-on card. For this motherboard, the TOE device is built
inside the ICH9R South Bridge chip.) The options are Enabled and Disabled.
SERR Signal Condition
This setting specifies the ECC Error conditions that an SERR# is to be asserted.
The options are None, Single Bit, Multiple Bit, and Both.
4GB PCI Hole Granularity
This feature allows you to select the granularity of PCI hole for PCI slots. If MTRRs
are not enough, this option may be used to reduce MTRR occupation. The options
are: 256 MB, 512 MB, 1GB and 2GB.
Channel 0 Rank Sparing/Channel 1 Rank Sparing
Select Enable to enable the function of memory sparing for Memory Bus Branch 0
or Branch 1. The options are Enabled and Disabled.
Enhanced x8 Detection
Select Enabled to enable Enhanced x8 DRAM UC Error Detection. The options
are Disabled and Enabled.
4-11
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
Demand Scrubbing
Scrubbing is a process that allows the North Bridge to correct correctable memory
errors found on a memory module. When the CPU or I/O issues a demand- read
command, and the read data from memory turns out to be a correctable error, the
error is corrected and sent to the requestor (the original source). Memory is updated
as well. Select Enabled to use Demand Scrubbing for ECC memory correction.
Patrol Scrubbing
Scrubbing is a process that allows the North Bridge to correct correctable memory
errors detected on a memory module, and send the correction to the requestor (the
original source). When this item is set to Enabled, the North Bridge will read and
write back one cache line every 16K cycles, if there is no delay caused by internal
processing. By using this method, roughly 64 GB of memory behind the North Bridge
will be scrubbed every day. The options are Enabled and Disabled.
Route Port 80h Cycles to
This feature allows the user to decide which bus to send debug information to. The
options are Disabled, PCI and LPC.
Enable Multi-Media Timer
Select Yes to activate a set of timers that are alternative to the traditional 8254
timers for the OS use. The options are Yes and No.
USB Host Controller
Select Enabled to enable USB Host Controller 1. The options are Enabled and
Disabled.
Legacy USB Support
This setting allows you to enable support for Legacy USB devices. The settings
are Enabled and Disabled.
Advanced Processor Options
Access the submenu to make changes to the following settings.
CPU Speed
This is a display that indicates the speed of the installed processor.
Frequency Ratio (Available if supported by the CPU.)
The feature allows the user to set the internal frequency multiplier for the CPU.
The options are: Default, x12, x13, x14, x15, x16, x17 and x18. Note: the options
will vary depending on the type of CPU installed.
4-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: BIOS
Core-Multi-Processing (Available if supported by the CPU.)
Set to Enabled to use a processor's Second Core and beyond. (Please refer to
Intel's web site for more information.) The options are Disabled and Enabled.
Machine Checking (Available when supported by the CPU.)
Set to Enabled to activate the function of Machine Checking and allow the CPU to
detect and report hardware (machine) errors via a set of model-specific registers
(MSRs). The options are Disabled and Enabled.
Thermal Management 2 (Available if supported by the CPU.)
Set to Enabled to use Thermal Management 2 (TM2) which will lower CPU voltage
and frequency when the CPU temperature reaches a predefined overheat threshold.
Set to Disabled to use Thermal Manager 1 (TM1), allowing CPU clocking to be
regulated via CPU Internal Clock modulation when the CPU temperature reaches
the overheat threshold.
C1 Enhanced Mode (Available if supported by the CPU.)
Set to Enabled to enable Enhanced Halt State to lower CPU voltage/frequency to
prevent overheat. The options are Enabled and Disabled. (Note: please refer to
Intel’s web site for detailed information.)
Execute Disable Bit (Available if supported by the CPU and the
OS.)
Set to Enabled to enable Execute Disable Bit and allow the processor to classify
areas in memory where an application code can execute and where it cannot, and
thus preventing a worm or a virus from inserting and creating a flood of codes to
overwhelm the processor or damage the system during an attack. This feature is
available when your OS and your CPU support the function of Execute Disable
Bit. The options are Disabled and Enabled. Note: For more information regarding
hardware/software support for this function, please refer to Intel's and Microsoft's
web sites.
Adjacent Cache Line Prefetch (Available when supported by the CPU.)
The CPU fetches the cache line for 64 bytes if this option is set to Disabled. The
CPU fetches both cache lines for 128 bytes as comprised if Enabled. The options
are Disabled and Enabled.
Hardware Prefetcher (Available when supported by the CPU.)
Set to this option to enabled to enable the hardware components that are used in
conjunction with software programs to prefetch data in order to shorten execution
cycles and maximize data processing efficiency. The options are Disabled and
Enabled.
4-13
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
Intel ® Virtualization Technology (Available if supported by the
CPU.)
Select Enabled to use the feature of Virtualization Technology to allow one platform
to run multiple operating systems and applications in independent partitions, creating
multiple "virtual" systems in one physical computer. The options are Enabled and
Disabled. Note: If there is any change to this setting, you will need to power off
and restart the system for the change to take effect. Please refer to Intel’s web site
for detailed information.
Intel EIST Support (Available if supported by the CPU.)
Select Enabled to use the Enhanced Intel SpeedStep Technology and allows the
system to automatically adjust processor voltage and core frequency in an effort
to reduce power consumption and heat dissipation. The options are Enabled and
Disabled. Please refer to Intel’s web site for detailed information.
CPU Cache Control
DCU Prefetch (Available when supported by the CPU.)
The CPU fetches the cache line for 64 bytes if this option is set to Disabled.
The CPU fetches both cache lines for 128 bytes as comprised if Enabled. The
options are Disabled and Enabled.
IP Prefetch (Available when supported by the CPU.)
Select Enabled to use CPU Cache Line IP Prefetch. The options are Disabled
and Enabled.
Direct Cache Access (Available when supported by the CPU.)
Set to Enable to route inbound network IO traffic directly into processor caches
to reduce memory latency and improve network performance. The options are
Disabled and Enabled.
I/O Device Configuration
Access the submenu to make changes to the following settings.
KBC Clock Input
This setting allows you to select clock frequency for the keyboard clock. The options
are 6MHz, 8MHz, 12MHz, and 16MHz.
Serial Port A
This setting allows you to decide how Serial Port A is controlled. The options are
Enabled (user defined), Disabled, and Auto (BIOS- or OS- controlled).
4-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: BIOS
Base I/O Address
This setting allows you to select the base I/O address for Serial Port A. The options
are 3F8, 2F8, 3E8, and 2E8.
Interrupt
This setting allows you to select the IRQ (interrupt request) for Serial Port A. The
options are IRQ3 and IRQ4.
Serial Port B
This setting allows you to decide how Serial Port B is controlled.The options are
Enabled (user defined), Disabled, Auto (BIOS controlled) and OS Controlled.
Mode
This setting allows you to set the type of devices to be connected to Serial Port B.
The options are Normal and IR (for an infrared device) and ASK-IR.
Base I/O Address
This setting allows you to select the base I/O address for Serial Port B. The options
are 3F8, 2F8, 3E8 and 2E8.
Interrupt
This setting allows you to select the IRQ (interrupt request) for Serial Port B. The
options are IRQ3 and IRQ4.
Floppy Disk Controller
This setting allows you to decide how Floppy Disk Controller is controlled.The options
are Enabled (user defined), Disabled, and Auto (BIOS- and OS- controlled).
Base I/O Address
This setting allows you to select the base I/O address for the Floppy disk drive.
The options are Primary and Secondary.
DMI Event Logging
Access the submenu to make changes to the following settings.
Event Log Validity
This is a display to inform you of the event log validity. It is not a setting.
Event Log Capacity
This is a display to inform you of the event log capacity. It is not a setting.
View DMI Event Log
Highlight this item and press <Enter> to view the contents of the event log.
4-15
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
Event Logging
This setting allows you to Enable or Disable event logging.
ECC Event Logging
This setting allows you to Enable or Disable ECC event logging.
Mark DMI Events as Read
Highlight this item and press <Enter> to mark the DMI events as read.
Clear All DMI Event Logs
Select Yes and press <Enter> to clear all DMI event logs. The options are Yes
and No.
Console Redirection
Access the submenu to make changes to the following settings.
COM Port Address
This item allows you to specify which COM port to direct the remote console to:
On-board COM A or On-board COM B. This setting can also be Disabled. Note:
The default is On-board COM B if IPMI is enabled.
BAUD Rate
This item allows you to set the BAUD rate for the remote console. The options are
300, 1200, 2400, 9600, 19.2K, 38.4K, 57.6K, and 115.2K.
Console Type
This item allows you to choose Console Redirection type. The options are VT100,
VT100/8bit, PC-ANSI/7bit, PC ANSI, VT100+, VT-UTF8 and ASCII.
Flow Control
This item allows you to set the flow control for Console Redirection. The options
are: None, XON/XOFF, and CTS/RTS.
Console Connection
This item allows you to decide how Console Redirection is to be connected: either
Direct or Via Modem.
Continue CR after POST
This item allows you to decide whether you want to continue with Console Redirection
after POST routines. The options are On and Off.
4-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: BIOS
Hardware Monitor
Highlight an item and hit <Enter> to see the status of each of the following items:
CPU Overheat Alarm
This option allows the user to select the CPU Overheat Alarm setting which de-
termines when the CPU OH alarm will be activated to provide warning of possible
CPU overheat. Refer to the the next item, CPU Temperature for more information
regarding PECI, DTS and other thermal features of this motherboard.
Warning: Any temperature that exceeds the CPU threshold temperature
predefined by the CPU manufacturer may result in CPU overheat or system
instability. When the CPU temperature reaches this predefined threshold,
the CPU and system cooling fans will run at full speed.
The options are:
The Default Alarm Setting: Select this setting if you want the CPU overheat alarm
(including the LED and the buzzer) to be triggered when the CPU temperature
reaches about +5 PECI counts above the threshold temperature as predefined by
the CPU manufacturer to give the CPU and system fans additional time needed
for CPU and system cooling.
The Early Alarm Setting: Select this setting if you want the CPU overheat alarm
(including the LED and the buzzer) to be triggered as soon as the CPU temperature
reaches the CPU overheat threshold as predefined by the CPU manufacturer.
CPU1 Temperature/CPU2 Temperature
The CPU Temperature feature will display the CPU temperature status as detected
by the BIOS:
Low – This level is considered as the ‘normal’ operating state. The CPU temperature
is well below the CPU ‘Temperature Tolerance’. The motherboard fans and CPU will
run normally as configured in the BIOS (Fan Speed Control).
User intervention: No action required.
Medium – The processor is running warmer. This is a ‘precautionary’ level and gen-
erally means that there may be factors contributing to this condition, but the CPU is
still within its normal operating state and below the CPU ‘Temperature Tolerance’.
The motherboard fans and CPU will run normally as configured in the BIOS. The
fans may adjust to a faster speed depending on the Fan Speed Control settings.
User intervention: No action is required. However, consider checking the CPU
fans and the chassis ventilation for blockage.
4-17
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
High – The processor is running hot. This is a ‘caution’ level since the CPU’s ‘Tem-
perature Tolerance’ has been reached (or has been exceeded) and may activate
an overheat alarm:
The Default Alarm – the Overheat LED and system buzzer will activate if the High
condition continues for some time after it is reached. The CPU fan will run at full
speed to bring the CPU temperature down. If the CPU temperature still increases
even with the CPU fan running at full speed, the system buzzer will activate and
the Overheat LED will turn on.
The Early Alarm – the Overheat LED and system buzzer will be activated exactly
when the High level is reached. The CPU fan will run at full speed to bring the
CPU temperature down.
Note: In both the alarms above, please take immediate action as shown below.
See CPU Overheat Alarm to modify the above alarm settings.
User intervention: If the system buzzer and Overheat LED has activated, take
action immediately by checking the system fans, chassis ventilation and room
temperature to correct any problems. Note: the system may shut down if it con-
tinues for a long period to prevent damage to the CPU.
Notes: The CPU thermal technology that reports absolute temperatures
(Celsius/Fahrenheit) has been upgraded to a more advanced feature by
Intel in its newer processors. The basic concept is each CPU is embedded
by unique temperature information that the motherboard can read. This
‘Temperature Threshold’ or ‘Temperature Tolerance’ has been assigned
at the factory and is the baseline on which the motherboard takes action
during different CPU temperature conditions (i.e., by increasing CPU Fan
speed, triggering the Overheat Alarm, etc). Since CPUs can have different
‘Temperature Tolerances’, the installed CPU can now send information to
the motherboard what its ‘Temperature Tolerance’ is, and not the other way
around. This results in better CPU thermal management.
Supermicro has leveraged this feature by assigning a temperature status to certain
thermal conditions in the processor (Low, Medium and High). This makes it easier
for the user to understand the CPU’s temperature status, rather than by just simply
seeing a temperature reading (i.e., 25oC).
The information provided above is for your reference only. For more information on
System Temperature
This feature displays the system's absolute temperature reading (i.e., 34oC).
4-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: BIOS
Fan1-Fan6 Speeds
If the feature of Auto Fan Control is enabled, the BIOS will automatically display
the status of the fans indicated in this item.
Fan Speed Control Modes
This feature allows the user to decide how the system controls the speeds of the
onboard fans. The CPU temperature and the fan speed are correlative. When the
CPU on-die temperature increases, the fan speed will also increase, and vise versa.
If the option is set to 3-pin fan, the fan speed is controlled by voltage. If the option
is set to 4-pin, the fan speed will be controlled by Pulse Width Modulation (PWM).
Select 3-pin if your chassis came with 3-pin fan headers. Select 4-pin if your chas-
sis came with 4-pin fan headers. Select Workstation if your system is used as a
Workstation. Select Server if your system is used as a Server. Select Disable to
disable the fan speed control function to allow the onboard fans to run at full speed
(12V) at all times. The Options are: 1. Disable (Full Speed), 2. 3-pin (Server), 3.
3-pin (Workstation), 4. 4-pin (Server) and 5. 4-pin (Workstation).
Voltage Monitoring
The following items will be monitored and displayed:
Vcore A, Vcore B, -12V, P1V5, +3.3V, 5Vsb, 5VDD, P_VTT, Vbat
Note: In the Windows OS environment, the Supero Doctor III settings take prece-
dence over the BIOS settings. When first installed, Supero Doctor III adopts the
temperature threshold settings previously set in the BIOS. Any subsequent changes
to these thresholds must be made within Supero Doctor, since the SD III settings
override the BIOS settings. For the Windows OS to adopt the BIOS temperature
threshold settings, please change the SDIII settings to be the same as those set
in the BIOS.
4-19
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
IPMI (The option is available only when an IPMI card is installed
in the system.)
IPMI Specification Version: This item displays the current IPMI Version.
BMC Hardware/Firmware Version: This item displays the current Firmware
Version.
System Event Logging
Select Enabled to enable IPMI Event Logging. When this function is set to Disabled,
the system will continue to log events received via system interface. The options
are Enabled and Disabled.
Clear System Event Logging
Enabling this function to force the BIOS to clear the system event logs during the
next cold boot. The options are Enabled and Disabled.
Existing Event Log Number
This item displays the number of the existing event log.
Event Log Control
System Firmware Progress
Enabling this function to log POST progress. The options are Enabled and
Disabled.
BIOS POST Errors
Enabling this function to log POST errors. The options are Enabled and
Disabled.
4-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: BIOS
BIOS POST Watch Dog
Set to Enabled to enable POST Watch Dog. The options are Enabled and Disabled.
OS Boot Watch Dog
Set to Enabled to enable OS Boot Watch Dog. The options are Enabled and
Disabled.
Timer for Loading OS (Minutes)
This feature allows the user to set the time value (in minutes) for the previous
item: OS Boot Watch Dog by keying-in a desired number in the blank. The default
setting is 10 (minutes.) (Please ignore this option when OS Boot Watch Dog is set
to "Disabled".)
Time Out Action
This feature allows the user to determine what action to take in an event of a system
boot failure. The options are No Action, Reset, Power Off and Power Cycles.
System Event Log/System Event Log (List Mode)
These options display the System Event (SEL) Log and System Event (SEL) Log
in List Mode. Items include: SEL (System Event Log) Entry Number, SEL Record
ID, SEL Record Type, Time Stamp, Generator ID, SEL Message Revision, Sensor
Type, Sensor Number, SEL Event Type, Event Description, and SEL Event Data.
4-21
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
Realtime Sensor Data
This feature display information from motherboard sensors, such as temperatures,
fan speeds and voltages of various components.
IPMI LAN Configuration
VLAN Tagging
Select Enabled to enable Virtual LAN(s) for IPMI connections and allow the user to
configure VLAN settings. The options are Enabled and Disabled.
VLAN ID
This item allows the user to change the VLAN ID. The default setting is 1h.
IP Address Source
This item allows the user to select the IP address source for the connection. The
options are DHCP and Static. If Static is selected, the following items need to be
set manually. Selecting DHCP will allow the network's DHCP server (if your network
has one) to assign values to these items automatically:
IP Address, IP Subnet Mask, Default Gateway
MAC Address
This is the system's hardware address. This do not need to be set or changed in
most cases.
Update LAN Settings
Select Yes to allow BIOS update LAN setting. The options are Yes and No.
4-22
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: BIOS
4-5
Security
Choose Security from the Phoenix BIOS Setup Utility main menu with the arrow
keys. You should see the following display. Security setting options are displayed
by highlighting the setting using the arrow keys and pressing <Enter>. All Security
BIOS settings are described in this section.
Supervisor Password Is:
This indicates if a supervisor password has been entered for the system. Clear
means such a password has not been used and Set means a supervisor password
has been entered for the system.
User Password Is:
This indicates if a user password has been entered for the system. Clear means
such a password has not been used and Set means a user password has been
entered for the system.
Set Supervisor Password
When the item Set Supervisor Password is highlighted, hit the <Enter> key. When
prompted, enter the Supervisor's password in the dialogue box to set or to change
supervisor's password, which allows access to the BIOS.
Set User Password
When the item Set User Password is highlighted, hit the <Enter> key. When
prompted, enter the user's password in the dialogue box to set or to change the
user's password, which allows access to the system at boot-up.
4-23
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
Password on Boot
This setting allows you to determine if a password is required for a user to enter
the system at bootup. The options are Enabled (password required) and Disabled
(a password not required).
4-6
Boot
Choose Boot from the Phoenix BIOS Setup Utility main menu with the arrow keys.
You should see the following display. See details on how to change the order and
specs of boot devices in the Item Specific Help window. All Boot BIOS settings are
described in this section.
Boot List
Candidate
List
Boot Priority Order/Excluded from Boot Orders
The devices included in the boot list section (above) are bootable devices listed in
the sequence of boot order as specified. The boot functions for the devices included
in the candidate list (above) are currently disabled. Use a <+> key or a <-> key to
move the device up or down. Use the <f> key or the <r> key to specify the type of
an USB device, either fixed or removable. You can select one item from the boot
list and hit the <x> key to remove it from the list of bootable devices (to make its
resource available for other bootable devices). Subsequently, you can select an
item from the candidate list and hit the <x> key to remove it from the candidate
list and put it in the boot list. This item will then become a bootable device. See
details on how to change the priority of boot order of devices in the "Item Specific
Help" window.
4-24
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: BIOS
4-7
Exit
Choose Exit from the Phoenix BIOS Setup Utility main menu with the arrow keys. You
should see the following display. All Exit BIOS settings are described in this section.
Exit Saving Changes
Highlight this item and press <Enter> to save any changes you have made and to
exit the BIOS Setup utility.
Exit Discarding Changes
Highlight this item and press <Enter> to exit the BIOS Setup utility without saving
any changes you may have made.
Load Setup Defaults
Highlight this item and press <Enter> to load the default settings for all items in
the BIOS Setup. These are the safest settings to use.
Discard Changes
Highlight this item and press <Enter> to discard (cancel) any changes you have
made. You will remain in the Setup utility.
Save Changes
Highlight this item and press <Enter> to save any changes you made. You will
remain in the Setup utility.
4-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: POST Error Beep Codes
Appendix A
POST Error Beep Codes
This section lists POST (Power On Self Test) error beep codes for the Phoenix BIOS.
POST error beep codes are divided into two categories: recoverable and terminal.
This section lists Beep Codes for recoverable POST errors.
Recoverable POST Error Beep Codes
When a recoverable type of error occurs during POST, BIOS will display a POST
code that describes the problem. BIOS may also issue one of the following beep
codes:
1 long and two short beeps - video configuration error
1 repetitive long beep - no memory detected
1 continuous beep with the front panel Overheat LED on - system overheat
A-1
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
Notes
A-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B: Installing the Windows OS
Appendix B
Installing the Windows OS
After all hardware components have been installed, you must first configure Intel
South Bridge RAID Settings before you install the Windows OS and other software
drivers. To configure RAID settings, please refer to RAID Configuration User Guides
B-1 Installing the Windows XP/2000/2003 OS for
Systems with RAID Functions
1. Insert Microsoft's Windows XP/2000/2003 Setup CD in the CD Driver, and the
system will start booting up from CD.
2. Press the <F6> key when the message-" Press F6 if you need to install a
third party SCSI or RAID driver" displays.
3. When the Windows XP/2000/2003 Setup screen appears, press "S" to specify
additional device(s).
4. Insert the driver diskette-"Intel AA RAID XP/2000/2003 Driver for ICH9R" into
Drive A: and press the <Enter> key.
5. Choose the Intel(R) ICH9R SATA RAID Controller from the list indicated in
the XP/2000/2003 Setup Screen, and press the <Enter> key.
6. Press the <Enter> key to continue the installation process. (If you need to
specify any additional devices to be installed, do it at this time.) Once all
devices are specified, press the <Enter> key to continue with the installation.
7. From the Windows XP/2000/2003 Setup screen, press the <Enter> key. The
XP/2000/2003 Setup will automatically load all device files and then, continue
the Windows XP/2000/2003 installation.
8. After the Windows XP/2000/2003 OS Installation is completed, the system will
automatically reboot.
B-1
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
B-2 Installing the Windows XP/2000/2003 OS for
Systems without RAID Functions
1. Insert Microsoft's Windows XP/2000/2003 Setup CD in the CD Driver, and the
system will start booting up from CD.
2. Continue with the OS installation. The Windows OS Setup screen will display.
3. From the Windows XP/2000/2003 Setup screen, press the <Enter> key. The
XP/2000/2003 Setup will automatically load all device files and then continue
with the Windows XP/2000/2003 installation.
4. After the Windows XP/2000/2003 OS Installation is completed, the system will
automatically reboot.
5. Insert the Supermicro Setup CD that came with your motherboard into the CD
Drive during system boot, and the main screen will display.
B-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C: Installing Other Software Programs and Drivers
Appendix C
Software Installation
C-1
Installing other Drivers and the OS
After you've installed the Windows Operating System, a screen as shown below
will appear. You are ready to install software programs and drivers that have not
yet been installed. To install these software programs and drivers, click the icons
to the right of these items.
Driver/Tool Installation Display Screen
Notes:
1. Click the icons showing a hand writing on the paper to view the readme files
for each item. Click a computer icon on the right of an item to install an item (from
top to the bottom) one at a time. After installing each item, you must reboot
the system before proceeding with the next item on the list.
2. The X7DCL-3 supports SAS RAID features. To configure the LSI SAS HostRAID,
please refer to the LSI folder for the LSI SAS HostRAID Utility and documentation.
The LSI folder is included in the CD-ROM that came with your motherboard.
C-1
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
C-2
Configuring Supero Doctor III
The Supero Doctor III program is a Web-based management tool that supports
remote management capability. It includes Remote and Local Management tools.
The local management is called the SD III Client. The Supero Doctor III program
included on the CDROM that came with your motherboard allows you to monitor
the environment and operations of your system. Supero Doctor III displays crucial
system information such as CPU temperatures, system voltages and fan status.
See the Figure below for a display of the Supero Doctor III interface.
Note 1: Both default username and password are ADMIN.
Note 2: In the Windows OS environment, the Supero Doctor III settings take
precedence over the BIOS settings. When first installed, Supero Doctor III adopts
the temperature threshold settings previously set in the BIOS. Any subsequent
changes to these thresholds must be made within Supero Doctor, since the SD
III settings override the BIOS settings. For the Windows OS to adopt the BIOS
temperature threshold settings, please change the SDIII settings to be the same
as those set in the BIOS.
Supero Doctor III Interface Display Screen-I (Health Information)
C-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C: Installing Other Software Programs and Drivers
Supero Doctor III Interface Display Screen-II (Remote Control)
supermicro.com/utility/Supero_Doctor_III/. You can also download SDIII User's
For the Linux OS, we will still recommend that you use Supero Doctor II.
C-3
Download from Www.Somanuals.com. All Manuals Search And Download.
X7DCL-3/X7DCL-i User's Manual
Notes
C-4
Download from Www.Somanuals.com. All Manuals Search And Download.
(Disclaimer Continued)
The products sold by Supermicro are not intended for and will not be used in life support systems, medical equipment, nuclear facilities or systems, aircraft, aircraft devices,
aircraft/emergency communication devices or other critical systems whose failure to perform be reasonably expected to result in significant injury or loss of life or catastrophic
property damage. Accordingly, Supermicro disclaims any and all liability, and should buyer use or sell such products for use in such ultra-hazardous applications, it does so
entirely at its own risk. Furthermore, buyer agrees to fully indemnify, defend and hold Supermicro harmless for and against any and all claims, demands, actions, litigation, and
proceedings of any kind arising out of or related to such ultra-hazardous use or sale.
Download from Www.Somanuals.com. All Manuals Search And Download.
|