SY-K7ADA
Motherboard
Quick Start Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-K7ADA Quick Start Guide
1
Introduction
SY-K7ADA
Quick Start Guide
Motherboard. This
Congratulations on your purchase of the
illustrates the steps for installing and setting up your new Motherboard.
This guide provide users with the basic steps of Motherboard setting and operation. For
SY-K7ADA User’s Guide
further information, please refer to the
Motherboard.
that came with your
Unpacking
When unpacking the Motherboard, check for the following items:
u
u
The SY-K7ADA ALi MAGiK1 AGP/PCI Motherboard
The Quick Start Guide
u
u
u
u
u
The Installation CD-ROM
SOYO Bonus Pack CD-ROM
One IDE Device ATA33/ 66/100 Flat Cable
One Floppy Disk Drive Flat Cable
One Heat Sink Compound
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-K7ADA Quick Start Guide
SY-K7ADA Motherboard Layout
PS/2 KB
Connector
PS/2 Mouse
Connector
JP1
1
3
USB 1_2
COMA
FJ1
PRT
COMB
AGAME
ATX Power
®
ALi
AOUT
AIN
M1647
VJ1
AMIC
IDE 2 IDE 1
3
1
ALi
M5879
VJ2
AGP Slot
4
1
Sigmatel
STAC9700
CDIN1
PCI Slot #1
PCI Slot #2
PCI Slot #3
PCI Slot #4
ALi
M5819
ALi
FLP
M1535D+
RJ2
3
RJ1
1
3V
Lithium
Battery
PCI Slot #5
RJ3
3
1
1112 13 14 15 16 17 18 19 20
JP5
1
2
3
4
5
9
10
JP10
WOL
Header
3
1
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-K7ADA Quick Start Guide
Key Features
Ø
Ø
Ø
Supports Socket A (Socket 462)
AMD® processors
Supports multiple-boot function
5 x 32-bit bus mastering PCI slots
fully compliant with PCI Rev2.2
¡
X
l
Supports 200MHz Front Side Bus
Athlon(750MHz~1.3GHz)
Ø
1 x 32-bit AGP 1X/2X/4X sideband
function slot, supports AGP
specification V2.0
l
Duron (600MHz~900MHz)
¡
X
Supports 266MHz Front Side Bus
Ø
Ø
l
6 x USB ports onboard compliant
with open HCI 1.0a specification
Athlon(1GHz~1.33GHz)
Ø
PC99, ACPI 1.0b
1 x IrDA port supports IrDA 1.0(SIR),
IrDA1.1 (FIR) & Sharp-IR
Ø
Ultra DMA33/66/100 (ATA 33/66/100)
EIDE
Ø
Ø
ATX power connector
Ø
Ø
Ø
Supports Wake-On-LAN (WOL)
Power-on by RTC alarm
Easy CPU settings in BIOS with the
“SOYO COMBO setup”
Supports onboard hardware
monitoring and includes Hardware
DoctorTM utility
Ø
Supports Suspend to RAM and
suspend to Disk
Ø
Ø
Supports on-board AC97 Audio
Ø
Supports three PC2100/PC1600
DDR SDRAM DIMMs up to 3GB
memory space
Supports CPU voltage adjustment
by DIP switch
Ø
Ø
Supports CPU Multiplier selection by
DIP switch
Supports CPU frequency adjustment
by DIP switch
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-K7ADA Quick Start Guide
2
Installation
To avoid damage to your Motherboard, please follow these simple rules while
handling this equipment:
l
Before handling the Motherboard, ground yourself by touching an unpainted portion of
the system's metal chassis.
l
l
Remove the Motherboard from its anti-static packaging. Hold the motherboard by the
edges and avoid touching its components.
Check the Motherboard for damage. If any chip appears to be loose, press carefully
to seat it firmly in its socket.
Follow the directions in this section which is designed to guide you through a quick and
SY-K7ADA
SY-K7ADA Motherboard User's guide and Technical Reference
correct method to install your new
Motherboard. For detailed information, please
refer to the
the CD-ROM package that came with your Motherboard.
online manual in
Gather and prepare all necessary components to complete the installation successfully:
u
u
u
u
u
u
u
u
u
u
AMD® Socket462 processor with built-in CPU cooling fan (boxed type)
DDR RAM module(s)
Computer case with adequate power supply unit
Monitor
PS/2 Keyboard
Pointing Device (PS/2 Mouse)
Speaker(s) (optional)
Disk Drives: HDD, CD-ROM, Floppy drive…
External Peripherals: Printer, Plotter, and Modem (optional)
Internal Peripherals: Modem and LAN cards (optional)
Note: 1.
If you want to use an external speaker connected to "Line-out" port, please make
sure to use an "amplified speaker" that can generate proper output sound volume.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-K7ADA Quick Start Guide
Install the Motherboard
SY-K7ADA
To perform the installation of your new
Motherboard, follow the steps below:
Step 1. CPU Installation
Record the working frequency of your CPU that
Mark your CPU Frequency:
should be clearly marked on the CPU cover.
200MHz FSB Athlon CPU
750 MHz (100 x 7.5)
950 MHz (100 x 9.5)
1.3 GHz (100 x 13.0)
800 MHz (100 x 8.0)
850 MHz (100 x 8.5)
1.1GHz (100 x 11.0)
900 MHz (100 x 9.0)
1.2 GHz (100 x 12.0)
1000 MHz (100 x 10.0)
200MHz FSB Duron CPU
600 MHz (100 x 6.0)
650 MHz (100 x 6.5)
850 MHz (100 x 8.5)
700 MHz (100 x 7.0)
900 MHz (100 x 9.0)
750 MHz (100 x 7.5)
800 MHz (100 x 8.0)
266MHz FSB Athlon CPU
1 GHz (133 x 7.5)
1.13 GHz (133 x 8.5)
1.2 GHz (133 x 9.0)
1.33 GHz (133 x 10.0)
® & Athlon/DuronTM processor that you
CPU Mount Procedure: To mount the AMD
have purchased separately, follow these instructions.
1
2
3
4
1.
2.
3.
4.
Lift the socket handle up to a vertical position.
Align the blunt edge of the CPU with the matching pinhole edge on the socket.
Seat the processor in the socket completely and without forcing.
Then close the socket handle to secure the CPU in place.
Remember to connect the CPU Cooling Fan to the appropriate power
The fan is a key component that stabilizes the
system. It prevents the equipment from overheating and prolongs the life of
connector on the Motherboard.
your CPU.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-K7ADA Quick Start Guide
Step 2.
Connections to the Motherboard
This section tells how to connect internal peripherals and the power supply to the Motherboard.
The internal peripherals consist of IDE devices (HDD, CD-ROM), Floppy Disk Drive, Chassis
Fan, Front Panel Devices (Suspend LED Internal Speaker, Reset Button and IDE LED
Switch.), Wake-On-LAN card, VGA card, Sound Card, and other devices.
For more details on connecting internal and external peripherals to your new SY-K7ADA
SY-K7ADA Motherboard User's Guide and Technical
Reference
Motherboard, please refer to
online manual on the CD-ROM.
Connectors and Plug-ins
Standard IrDA (Infrared Device Header): SIRCON
Wake-On-LAN Header: JP10
Pin1
+5V
Pin2
FIR
Pin3
Pin4
Pin5
Pin6
OVCROFF
Pin1
Pin2
Pin3
IRRX
GND
IRTX
5VSB
GND
PME #
USB3_4: USB3
USB3_4: USB4
Pin1
Pin2
Pin3
Pin4
Pin6
+5V
Pin7
Pin8
Pin9
GND
Pin10
GND
+5V
Data(-)
Data(+)
GND
Data(-) Data(+)
USB5_6: USB5
USB5_6: USB6
Pin1
+5V
Pin2
Pin3
Pin4
Pin6
+5V
Pin7
Pin8
Pin9
Pin10
GND
Data(-)
Data(+)
GND
Data(-) Data(+) GND
CPU Cooling Fan:
CPUFAN
SYS Cooling Fan:
Chassis Fan: CHAFAN
Pin1 Pin2 Pin3
+12V SENSOR PWM2 +12V SENSOR GND
CD Line-in: CDIN1
SYSFAN
Pin1
GND
Pin2
Pin3
Pin1
Pin2
+12V
Pin3
NC
Pin 1
CD_L
Pin 2
GND
Pin 3
GND
Pin 4
CD_R
Connect the CD Line-in cord from the CD-ROM device to
the matching header CDIN1
Power LED
Pin11
LED
Pin12
NC
Pin13
GND
1112 13 14 15 16 17 18 19 20
Speaker
1
2
3
4
5
9
10
Pin17
Power
Pin18
NC
Pin19
NC
Pin20
Speaker out
HDD LED
PWRBT
RESET
Suspend LED
Pin9
Power
Pin10
HDD LED PWRBTN
Pin4
Pin5
GND
Pin1
Power RST
Pin2
GND
Pin7
Power
Pin8
SP_LED
ATX POWER On/Off : PWRBT
Connect your power switch to this header (momentary switch type).
To turn off the system, please press this switch and hold down for longer than 4
seconds.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-K7ADA Quick Start Guide
ATX Power Supply: ATX PW
Attach the ATX Power cable to this connector. (This motherboard requires an ATX power supply, an AT
power supply can NOT be used.)
When using the Power-On by PS/2 Keyboard function, please make sure the ATX power supply is able to
provide at least 720mA on the 5V Standby lead (5VSB) in order to meet the standard ATX specifications.
Step 3. Configure Memory
Supports PC2100/PC1600 DDR(Double Data Rate) SDRAM up to 3 DIMMs and using
system memory up to 3GB. Supports symmetrical and asymmetrical DDR addressing.
Memory Configuration Table
Number of Memory Modules
DIMM 1
DIMM 2
DIMM3
RAM Type
DDR SDRAM
Memory Module Size
4/16/64/128/256/512 Mbit
Note: This Motherboard can only support 2 pcs of PC2100 DDR module, we
suggest using DIMM1 and DIMM2 for PC2100 DDR module.
Step 4. Multiplier Adjustment Setting (RJ1)
Ô
For certain AMD CPUs, the multiplier is not locked such that setting a multiplier higher
than specified on the CPU is possible. For technical details read the following:
Refer to the following table to set the Frequency Multiplier of your CPU.
Frequency Multiplier
RJ2
Short Pin1-2
RJ3
Short Pin1-2
Setting
Auto
1 2
3
1 2
3
Short Pin2-3
Short Pin2-3
Manual
1 2
3
1 2
3
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-K7ADA Quick Start Guide
If you set ratio to manual and configure the RJ1 DIP switch to the settings that match your CPU speed, as
follow table:
RJ1
5
5.5
6
1
2
3
Off
Off
4
RJ1
9
9.5
10
1
2
3
4
Off Off
Off Off
On On
Off
On
On
On
On
On On
Off
On
On
Off Off
On
Off Off Off
Off Off Off
On On On
Off Off Off Off
On On On On
6.5
7
7.5
8
On 10.5
Off
Off
Off
Off
11
11.5
12
Off
Off
On On
On On On
Off
Off Off
Off
Off Off
On
On
On
On
On On
On On
8.5
12.5
Note: SOYO does not guarantee system stability if the user over clocks the
system. Any malfunctions due to over-clocking are not covered by the warranty.
Step 5. Enable/Disable Power-On by Keyboard (JP1)
You may choose to enable the Power-On through Keyboard function by shorting pin 2-3 on
jumper JP1; or short pin 1-2 to disable this function.
Power-On by
Keyboard
Enable
Disable
Short pin 2-3 to
enable the Power-
On by Keyboard
function.
Short pin 1-2 and
the Power-On by
Keyboard function is
disabled.
JP1 Setting
1 2
3
1
2
3
Important: When using the Power-On by Keyboard function, please make sure the
ATX power supply is able to provide at least 720mA on the 5V Standby lead (5VSB)
in order to meet the standard ATX specification.
Step 6. The synchronous / asynchronous clock mode between CPU
and memory interface setting
The FSB Frequency can also be set through DIP switch FJ1 or BIOS and it may therefore
differ from the Frequency the CPU specifies. Doing so may however force your CPU to
operate out of its specifications and therefore SOYO can not guarantee the proper
functioning of your system.
Refer to the following table:
10
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-K7ADA Quick Start Guide
FJ1– CPU frequency setting
CPU Freq(MHz) SDRAM(MHz)
1
2
3
4
Off
Off
Off
Off
100
133
100
133
On
On
On
Off
Step 7. CPU Vcore adjustment (VJ1)
Refer to following table to set the voltage of your CPU. If you set VJ2 status to AUTO, please
set VJ1 switch status to Off (all).
Status Setting
Manual
VJ2
Short Pin2-3
1 2
3
Short Pin1-2
Auto
1 2
3
If you set status to manual and configure VJ1 switch to the settings that match your CPU voltage
as follow table:
1
2
3
4
5
1
2
3
4
5
VJ1
VJ1
OFF OFF OFF OFF ON
ON OFF OFF OFF ON
OFF ON OFF OFF ON
Auto OFF OFF OFF OFF OFF 1.475
ON OFF OFF OFF OFF
OFF ON OFF OFF OFF
1.100
1.125
1.150
1.175
1.200
1.225
1.250
1.275
1.300
1.325
1.350
1.375
1.400
1.425
1.450
1.500
1.525
1.550
1.575
1.600
1.625
1.650
1.675
1.700
1.725
1.750
1.775
1.800
1.825
1.850
ON
ON OFF OFF OFF
ON
ON OFF OFF ON
OFF OFF ON OFF OFF
ON OFF ON OFF OFF
OFF OFF ON OFF ON
ON OFF ON OFF ON
OFF ON
ON ON
ON OFF OFF
ON OFF OFF
OFF ON
ON ON
ON OFF ON
ON OFF ON
OFF OFF OFF ON OFF
ON OFF OFF ON OFF
OFF ON OFF ON OFF
OFF OFF OFF ON
ON OFF OFF ON
OFF ON OFF ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON OFF ON OFF
ON
ON OFF ON
OFF OFF ON
ON OFF ON
ON OFF
ON OFF
ON OFF
ON OFF
OFF OFF ON
ON OFF ON
ON
ON
ON
ON
OFF ON
ON ON
ON
ON
OFF ON
ON ON
ON
ON
11
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-K7ADA Quick Start Guide
CMOS Clear (JP5)
In some cases the CMOS memory may contain wrong data, follow the steps below to clear
the CMOS memory.
1.
Clear the CMOS memory by momentarily shorting pin 2-3 on jumper JP5. This jumper
can be easily identified by its white colored cap.
2.
Then put the jumper back to 1-2 to allow writing of new data into the CMOS memory.
CMOS Clearing
Clear CMOS Data
Retain CMOS Data
Short pin 2-3 for
at least 5 seconds to
clear the CMOS
Short pin 1-2 to
retain new settings
JP5 Setting
1 2
3
1 2 3
Note: You must unplug the ATX power cable from the ATX power connector when
performing the CMOS Clear operation.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-K7ADA Quick Start Guide
3
Quick BIOS Setup
This Motherboard does not use any hardware jumpers to set the CPU frequency. Instead,
[SOYO COMBO SETUP].
CPU settings are software configurable with the BIOS
The
[SOYO COMBO SETUP] combines the main parameters that you need to configure, all in
one menu, for a quick setup in BIOS.
After the hardware installation is complete, turn the power switch on, then press the <DEL> key
during the system diagnostic checks to enter the Award BIOS Setup program. The CMOS
SETUP UTILITY will be shown on the screen. Then, follow these steps to configure the CPU
settings.
Step 1. Select [STANDARD CMOS SETUP]
Set [Date/Time] and [Floppy drive type], then set [Hard Disk Type] to “Auto”.
Step 2. Select [LOAD SETUP DEFAULT]
Select the “LOAD SETUP DEFAULT” menu and type “Y” at the prompt to load the BIOS
optimal setup.
Step 3. Select [SAVE & EXIT SETUP]
<Enter>
Press
sequence.
to save the new configuration to the CMOS memory, and continue the boot
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-K7ADA Quick Start Guide
4
The SOYO CD
The SOYO-CD will NOT autorun if you use it on an Operating System other
than Windows 9x or NT.
Your SY-K7ADA Motherboard comes with a CD-ROM labeled "SOYO CD." The SOYO
CD contains (1) the user's manual file for your new Motherboard, (2) the drivers/software
available for installation, and (3) a database in HTML format with information on SOYO
Motherboards and other products.
Step 1. Insert the SOYO CD into the CD-ROM drive
If you use Windows NT, the SOYO-CD will not detect your motherboard type. In that case
the following dialog will pop up, please choose your motherboard and press OK. Now the
SOYO-CD Start Up Menu will be shown.
X
Please Select Your Board
LI-7000
7IWB
7IWA-F
7IWA-F V1.0
6IWM/L
6IWM
7IWB V1.0
7IWM
6IWA
7IWM/L V1
Cancel
OK
(SOYO CD Start Up Program Menu)
If you use Windows 95 or 98, the SOYO CD Start Up Program automatically detects
which SOYO Motherboard you own and displays the corresponding model name.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-K7ADA Quick Start Guide
The user's manual files included on the SOYO CD are in PDF (Postscript Document)
format. In order to read a PDF file, the appropriate Acrobat Reader software must be
installed in your system.
Note:
The Start Up program automatically detects if the Acrobat Reader utility is already
present in your system, and otherwise prompts you on whether or not you want to install it.
You must install the Acrobat Reader utility to be able to read the user's manual file. Follow
the instructions on your screen during installation, then once the installation is completed,
restart your system and re-run the SOYO CD.
Step 2. Install Drivers and Utilities
Install Drivers
Click the
button to display the list of drivers/ software that can be installed
with your Motherboard. The Start Up program displays the drivers available for the
particular model of Motherboard you own. We recommend that you only install those
drivers.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-K7ADA Quick Start Guide
driver
revision:
ALi AGP Driver for win 9x/2000
ALi Onboard Audio Driver for win 9x/2000
ALi Onboard Audio Driver for win NT4.0
ALi Hardware monitor(R) Driver for win 9x/98ME
ALi Hardware monitor(R) Driver for win NT/2000
Cancel
OK
(Driver Installation Menu)
A short description of all available drivers follows:
Ø
ALi AGP driver for Win 9x/2000
The ALi AGP driver package includes below drivers your motherboard needs. After
selecting this driver package, one driver will be installed automatically. A description of the 2
drivers follows:
¾
ALi IDE driver
This driver will speed up the data-transfer rate to and from the harddisk.
¾
ALi AGP Driver
This driver must be installed in order to be able to make use of the AGP Video
functionality.
Ø
ALi Onboard Audio Driver for win 9x/2000
You have to install the drivers before installing any application for the Onboard Audio.
ALi Onboard Audio Driver for win NT4.0
You have to install the drivers before installing any application for the Onboard Audio.
ALi hardware monitor(R) for win 9x/98ME
Ø
Ø
Your motherboard comes with a hardware monitoring IC. By installing this utility
Temperature, Fan speed and Voltages can be monitored. It is also possible to set alarms
when current system values exceed or fall below pre-set values.
Ø
ALi hardware monitor(R) for win NT/2000
Your motherboard comes with a hardware monitoring IC. By installing this utility
Temperature, Fan speed and Voltages can be monitored. It is also possible to set alarms
when current system values exceed or fall below pre-set values.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-K7ADA Quick Start Guide
OK, Cancel
Select which driver you want to install and click
installation and return to the main menu.
or click
to abort the driver
Note:
Once you have selected a driver, the system will automatically exit the SOYO CD to
begin the driver installation program. When the installation is complete, most drivers
require to restart your system before they can become active.
Step 3.
1.For supporting S3 mode wake up function in WINDOWS 98se, please download
the driver from SOYO web site (www.soyo.com.tw).
Please put this downloaded driver in c:\windows\system32\driver and remove USB
device in “Device Manager” then refresh.
Please put this downloaded driver in c:\windows\system32\driver
17
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-K7ADA Quick Start Guide
Remove USB device(ex : USB keyboard, mouse, …,etc.)
Refresh
18
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-K7ADA Quick Start Guide
Final
2.If customer uses the WINDOWS 95 OSR2, please use the NT version driver
when installing audio driver.
3.Right now, ALI chipset does not support ATI RAGE 128 graphics chip, so K7ADA
can not support this kind of VGA card.
Step 4. Check the Latest Releases
Click the 'Check the latest Releases' button to go the SOYO Website to automatically find
the latest BIOS, manual and driver releases for your motherboard. This button will only
work if your computer is connected to the internet through a network or modem
connection. Make sure to get your modem connection up before clicking this button.
(* Internet Explorer is a Microsoft Trademark)
19
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-K7ADA Quick Start Guide
Quick Trouble shoot tips
Video (no display) related issues
I built a new computer system using a Soyo board and nothing happens when
turning it on, no video and no beeps from the PC speaker. What is happening
and how can it be fixed?
No screen and no beeps mean that your CPU and motherboard do not work at all. It
could be that the CPU is not seated correctly or that a component on the M/B is
grounded (shorted) with the case. Also make sure to check the voltage setting
switch (110V/220V) on the back of the power supply. To isolate the problem do
the following:
1. Press and hold down on the “Ins” (insert) key while turning on the computer
until you get video. If you do not get video then,
2. Double-check jumpers setting on you motherboard and remove all add-on
cards, unplug all hard-disk and floppy-disk drive cables and see if you can hear
some beeps. If you still do not get any beeps, then try putting the motherboard on
the table (to isolate it from the case) with the CPU and speaker only, and give it one
more try.
I hear a series of beeps and I do not get anything from my monitor. What
could be wrong?
The following lists some basic beep codes and their possible meanings:
·
One long beep and 3 very short beeps - The video card is not detected by
the motherboard. Please re-seat your video card. If you are using an AGP
card, please push your AGP card down real hard. You may have to push
VERY hard without the AGP card mounting screw. Make sure not to
insert the card the other way around.
·
Continuous beeps – One or more of the memory modules is not seated
correctly in its socket.
My PCI VGA card works fine with my system, but when I put in a new AGP
card, it does not give me any video. Is my AGP slot bad?
This is a common problem with AGP video cards. The reason is that your AGP
card did not get seated into the AGP slot fully and firmly. Please push your AGP
card down into the socket real hard, it should snap twice. You may have to unscrew
the AGP card to allow the card to go further down. Do take care not to damage the
card by using too much force.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-K7ADA Quick Start Guide
I get distorted video my AGP card right after I save my bios. Why is that?
The cause is likely that your AGP card is not running at the correct bus speed. To
fix this, please clear the CMOS via JP5 and if it still does not work, please upgrade
your motherboard bios to the latest version.
BIOS Issues
Where can I find the BIOS revision of my mainboard?
It will be displayed on the up-left corner on the screen during boot-up. It will show
as your board type followed by the revision number, such as 5EH_2CA1 (meaning
revision 2CA1 for the SY-5EH board) or 6BA+ IV_2AA2 which means SY-6BA+
IV motherboard with 2AA2 bios.
Where can I find the latest BIOS of my motherboard?
Please go to the technical support page of one of the SOYO websites (Taiwan:
www.soyo.com.tw), and look up your motherboard to find the latest BIOS
revision.
Hard disk, floppy drive, CD-ROM etc
When I boot up my new computer I got "floppy boot failure" and the LED on
the floppy stays on
Make sure the red wire of floppy ribbon cable goes to Pin1 on the floppy drive side
(don't trust the "key lock" or "notch") and use the end-connector of the cable (don't
use middle one).
Modem issues
I get an "I/O Conflict" message when I turn on my system and I can not get
my modem to work
What you need to do is to disable 'COM2' (or UART2 or serial port 2) in the bios
under integrated peripheral setup.
I have installed my modem drivers several times and I still cannot get my
modem to work. Why?
If you are sure that the modem driver has been installed correctly, then you need to
install the via 4 in 1 driver from the SOYO CD, this is because Windows does not
properly recognize relatively new chipsets.
I can not get my board to run properly.
Please make sure you have the latest bios and driver from the SOYO web site at:
21
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-K7ADA Quick Start Guide
How to contact us:
n
If you are interested in our products, please contact the SOYO sales
department in the region you live.
n
If you require Technical Assistance, please contact our Technical Support in
the region you live.
SOYO prefers Email as communication medium, remember to always add to the
email the country that you live in.
TAIWAN
JAPAN
SOYO COMPUTER INC.
SOYO COMPUTER
No. 21 Wu-Kung 5 Rd., Hsin Chuang
City, Taipei Hsien, Taiwan, R.O.C
TEL: 886-2-22903300
SOYO BLDG, 1-23-14, Hyakunincho,
Shinjyuku-ku, Tokyo Japan 169-0073
TEL: 81-3-3368-2188
FAX: 886-2-22983322
FAX: 81-3-3368-2199
Email: [email protected]
Email: [email protected]
USA
CHINA
SOYO INC.
GING MEI JEI LTD
41484 Christy Street, Fremont, CA
94538, USA
Room 304, Phoenix Mansion, No. 165
Haidian Road, Haidian Distnct, Beijing
100080, China
TEL: 1-510-226-7696
TEL: 86-10-6251-0089
FAX: 1-510-226-9218
Email : [email protected]
FAX: 86-10-6251-0311
Email: [email protected]
GM
KOREA
SOYO Deutschland GmbH
SOYO TECHNOLOGY CO., LTD.
(SAAT Technology GmbH)
3 rd, F1, Wonhyo Bldg, 46-1,
Wonhyoro 3 Ga, yongsan Ku, Seoul
Korea
August-Wilhelm-Kuhnholz-Str. 15
D-26135 Oldenburg (Oldb), Germay
TEL: 49-441-209-100
TEL: 882-716-2850
FAX: 49-441-203-442
FAX: 882-704-2619
Email: [email protected]
Email: [email protected]
22
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-K7ADA Quick Start Guide
Hong Kong
Soyo (H.K.) Ltd.
5C, Big Star Centre, 8 Wang Kwong
Road, Kowloon Bay, Kowloon, HK
TEL: 852-2710-9810
FAX: 852-2710-9078
Email: [email protected]
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Edition: May 2001
Version 1.2
SY- K7ADA
SERIAL
Download from Www.Somanuals.com. All Manuals Search And Download.
|