Model No. 831.287941
Serial No.
USER'S MANUAL
The serial number can be found in
the location shown below. Write the
serial number in the space above.
Serial Number Decal
Patent Pending
CAUTION
Read all precautions and
instructions in this manual
before using this equipment.
Keep this manual for future ref-
erence.
SEARS, ROEBUCK AND CO., HOFFMAN ESTATES, IL 60179
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the new AEROBIC RIDER 2™
by HEALTHRIDER. The AEROBIC RIDER 2 offers a
unique form of low-impact exercise that uses both the
upper body and the lower body for greater cardiovas-
cular benefits and increased toning.
Saturday, 7 a.m. until 7 p.m. Central Time (excluding
holidays). To help us assist you, please note the prod-
uct model number and serial number before calling.
The model number is 831.287941. The serial number
can be found on a decal attached to the AEROBIC
RIDER 2 (see the front cover of this manual).
For your benefit, please read this manual carefully
before using the AEROBIC RIDER 2. If you have
additional questions, please call our toll-free
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
HELPLINE at 1-800-736-6879, Monday through
Handlebar
Center Post
Monitor
Padded Seat
Seat Knob
(Behind Weight
Saddle)
Upper Pedals
Lower Pedal
Spring Clip
Weight Tube
Weight
3
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Before beginning assembly, carefully read the
following information and instructions:
• Tighten all parts as you assemble them, unless
instructed to do otherwise.
• Assembly requires two persons.
• During assembly, make sure that all parts are ori-
ented as shown in the drawings.
• Place all parts in a cleared area and remove the
packing materials; do not dispose of the packing
materials until assembly is completed.
THE FOLLOWING TOOLS (NOT INCLUDED)
ARE REQUIRED FOR ASSEMBLY:
• Read each assembly step before you begin.
• Two (2) adjustable wrenches
• To identify the small parts used in assembly, use
the part identification chart below. The num-
ber in parenthesis below each part refers to the
key number of the part. The second number
refers to the quantity needed for assembly. Note:
Some parts may have been pre-attached for
shipping purposes. If a part is not in the parts
bag, check to see if it has been pre-attached.
• Lubricant, such as petroleum jelly or grease,
will also be required.
Assembly will be more convenient if you have the
following tools: A socket set, a set of open-end or
closed-end wrenches, and a rubber mallet.
Plastic Washer (49)–2
M6 Hex Nut (54)–4
M6 Flat Washer (55)–4
Rubber Washer (51)–4
Tree Fastener (45)–10
M8 Acorn Nut (56)–4
M8 Nylon Jam Nut (7)–1
M6 x 60mm Bolt (53)–4
M8 x 1.375” Bolt (17)–1
M8 x 157mm Axle (13)–2
4
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Before beginning assembly, make sure that you
have read and understand the information on
page 4.
1
Attach one of the Stabilizers (31) to the Main Frame
(1) with two M6 x 60mm Bolts (53), two M6 Flat
Washers (55), and two M6 Hex Nuts (54).
1
54
55
31
53
2. Attach the other Stabilizer (31) to the Main Frame
(1) with two M6 x 60mm Bolts (53), two M6 Flat
Washers (55), and two M6 Hex Nuts (54).
2
3
4
1
53
31
55
54
3. Attach the Front Cover Panel (34) to the Main
Frame (1) with four Tree Fasteners (45). If you can’t
push the Tree Fasteners in with your fingers, tap
them in with a rubber mallet.
1
45
34
4. Lubricate an M8 x 157mm Axle (13). Attach the
Handlebar Swing Arm (5) to the Main Frame (1)
with the M8 x 157mm Axle, two Rubber Washers
(51), and two M8 Acorn Nuts (56).
Lubricate—13
5
56
51
51
56
1
5
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Push the Magnet Bracket (36) into the hole in the
Pedal Frame (4).
5
56
51
Lubricate—13
1
Lubricate an M8 x 157mm Axle (13). Attach the
Pedal Frame (4) to the Main Frame (1) with the M8
x 157mm Axle, two Rubber Washers (51), and two
M8 Acorn Nuts (56).
51
56
4
36
Hole
6. Attach the Left Side Shield (21) to the Seat Frame
(2) using three Tree Fasteners (45). If you can’t
push the Tree Fasteners in with your fingers, tap
them in with a rubber mallet.
6
2
Attach the Right Side Shield (22, not shown) in the
same way.
45
21
45
7. While another person holds the Long Link Arm (10)
and the Short Link Arm (11) in place, put two Plastic
Washers (49) between them. Then, connect the
Seat Swing Arm (5), the Long Link Arm (10), and
the Short Link Arm (11) using an M8 x 1.375” Bolt
(17) and an M8 Nylon Jam Nut (7).
7
5
7
17
10
49
11
8. Remove the 1” x 2” Endcap (50) from the Seat
Frame (2). Slide the Weight Saddle (8) onto the
Seat Frame (2). Hook the tab on the Weight Saddle
(8) into the indicated hole in the Seat Frame (2).
8
20
8
Place the Seat (20) on the Weight Saddle (8). Slide
the Seat Washer (38) onto the Seat Knob Bolt (43)
and then tighten the Seat Knob (37) onto it.
43
50
Tab
Hole
2
38
37
6
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Depress the two buttons on the sides of the
Handlebar Assembly (6) with your thumb and fore-
finger. Insert the Handlebar Assembly (6) into the
Handlebar Swing Arm (5). Make sure that the but-
tons protrude through one of the two sets of holes
in the Handlebar Swing Arm. The upper holes offer
lower workout resistance; the lower holes offer
higher resistance.
9
6
Holes
5
Buttons
10. Slide the Monitor (35) fully onto the Main Frame (1)
as shown in inset drawing A. Press down on the
Monitor as shown in inset drawing B until it snaps
into place.
10
A
B
35
1
35
35
1
1
11. Remove the battery cover from the Monitor (35).
Insert two new AA batteries into the Monitor. Identify
the negative (–) and positive (+) ends of the batter-
ies. The springs in the battery compartment should
touch the negative ends of the batteries.
11
Battery
Cover
(+)
(–)
(–)
(+)
AA
Batteries
35
12. Make sure that all parts are properly tightened. To protect the floor or carpet from damage, place a mat
under the AEROBIC RIDER 2.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENT AND OPERATION
DESCRIPTION OF THE MONITOR
ADJUSTING THE SEAT
The monitor offers five modes to provide you with
instant exercise feedback:
To adjust the posi-
tion of the seat,
loosen the knob
under the seat,
move the seat to
the desired posi-
tion, and then
retighten the knob.
To determine if the
seat is properly
Seat
Knob
• Time—Displays
the elapsed time.
Note: If you stop
exercising, the
time mode will
pause after ten
seconds.
adjusted, sit on the seat and pull the handlebar as
close as possible to your stomach. Your legs should
be almost straight, with your knees bent slightly.
• Reps/Min—
Displays your
repetitions per
minute.
ADDING AND REMOVING WEIGHT
• Reps—Displays the total number of repetitions you
have completed, up to 3999. The display will then
reset to zero and continue counting.
The AEROBIC
RIDER 2 features a
weight bar that lets
you intensify your
exercise by adding
weights. To add
weights, first
Weight
• Calories—Displays the approximate number of
Calories you have burned.
• Scan—Displays all of the above modes, for approxi-
mately 5 seconds each, in a repeating cycle.
remove the spring
clips from the
Spring
Clip
weight bar. Slide
the desired amount
HOW TO OPERATE THE MONITOR
of weight onto the weight bar and reattach the spring
clips. Note: Place an equal amount of weight on
both sides of the weight bar. The combined
weight of the user and added weights should not
exceed 300 pounds.
1. To turn on the power, press the select button or
simply begin exercising. When the power is
turned on, the time mode will automatically be
selected.
2. Select the desired mode:
CHANGING THE POSITION OF THE HANDLEBAR
Time, reps/min, reps, or calories mode—To select
one of these modes, repeatedly press the select
button. The mode indicators will show which mode
is selected. Make sure that the scan indicator
does not appear.
To exercise the
muscles of the
lower body, the
position of the han-
dlebar can be
changed. Remove
6
3
28
5
Scan mode—When the scan mode is selected,
the scan indicator will appear and a mode indica-
tor will show which mode is currently displayed.
To select the scan mode, repeatedly press the
select button.
the Swing Arm Cap
(28) from the
Wheel Swing Arm
(3). Next, press the
Snap Buttons (46)
46
and slide the Handlebar Assembly (6) out of the
Handlebar Swing Arm (5). Press the Snap Buttons
again and insert the Handlebar Assembly into the
Wheel Swing Arm (3). Make sure that the Snap
Buttons snap into the holes in the Wheel Swing
Arm. Press the Swing Arm Cap (28) onto the
Handlebar Swing Arm (5).
3. The monitor has an “auto-off” feature. If the
pedals are not moved and the select button is not
pressed for four minutes, the power will turn off
automatically in order to conserve the batteries.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
PROPER EXERCISE FORM
ach or rib cage as possible. If you are new to
exercise, don’t extend the bar too far forward for
the first few weeks of your exercise program. As
your back becomes stronger and more flexible,
allow the handlebar to travel farther forward for
increased range-of-motion.
The following tips are provided to help you get the
most from your exercise routine:
• Always start each exercise session in the
standard workout position to warm up.
• Change grip positions, thumb positions, and toe
positions often to add variety, endurance, and bal-
ance to each workout.
• You should be able to feel yourself pivot or bend
from the hip, not from the back. Don’t round your
back as the bar moves forward.
• Always place the balls of your feet in the centers
of the pedals.
• Always bring the handlebar as close to your stom-
STANDARD WORKOUT POSITION
1
We strongly recommend that you begin every exercise session in this posi-
tion. As a warm-up, it provides a balanced workout, distributing the empha-
sis between upper and lower body. Vary emphasis by pulling more with the
arms or pushing more with the legs. Keep your back vertical and upright at
all times. You should also vary your hand grip to target certain muscle
groups. For example, a wide overhand grip will target your shoulders; a
close overhand grip (shown) will target your triceps; and a close underhand
grip will target your biceps.
Muscles affected: All Major Muscle Groups
WRIST ROLL
2
As your strength increases, you’ll want to challenge yourself by toning your
forearms even more. Use the wrist roll with either the close or wide over-
hand grip. As you pull the handlebar toward your stomach, roll your knuck-
les forward in a smooth motion.
Muscles affected: Forearm Flexors
CENTER POST GRIP
3
Grip the center post high with one hand above the other. Perform ten repe-
titions. Change your hand positions and perform the same number of repe-
titions. For greater emphasis try one hand at a time.
Muscles affected: Biceps and Chest
9
Download from Www.Somanuals.com. All Manuals Search And Download.
TOES STRAIGHT
4
Place the ball of each foot in the middle of each pedal. Push with your toes
pointed forward, then pull your feet back with toes up and heels down. This
tones the lower legs. Start with just a few minutes per session and gradual-
ly increase with each workout.
Muscles affected: Shins and Calves
TOES TURNED
5
The direction which your toes are turned will vary the effect of your work-
out. If your toes are turned slightly in while pointing and flexing, this
emphasizes the outer calves. If your toes are turned slightly out while
pointing and flexing, this emphasizes the inner calves. You can also turn
you toes out and open your knees to tone your inner thighs. Regardless of
which toe position you choose, always keep your kneecap in line with your
toes.
Muscles affected: Calves and Thighs
UPPER BODY EMPHASIS
6
Place your feet on the upper pedals and choose any grip.
Muscles affected: Arms, Upper Back, and Chest
LOWER BODY EMPHASIS
7
Grip the center post low and place your feet on the lower pedals. For more
emphasis on the stomach, tighten your abs and pull them in.
Muscles affected: Abdomen, Legs, and Lower Back
10
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE AND TROUBLE-SHOOTING
Inspect and tighten all parts of the AEROBIC RIDER 2 regularly. Keep the monitor out of direct sunlight or the dis-
play may be damaged. The AEROBIC RIDER 2 can be cleaned with a soft, damp cloth. Do not use solvents.
Keep liquid away from the monitor. When storing the AEROBIC RIDER 2, remove the battery from the monitor.
HOW TO REPLACE THE BATTERIES
If the display of the monitor becomes dim, the AA batteries should
be replaced. Remove the battery cover from the monitor. Remove
the old batteries. Insert two new batteries into the monitor. Identify
Battery
Cover
the negative (–) and positive (+) ends of the batteries. The springs
in the battery compartment should touch the negative ends of the
batteries.
(+)
(–)
Re-attach the battery cover to the monitor.
AA
Batteries
Monitor
HOW TO LUBRICATE THE AEROBIC RIDER 2
Every three months, a small amount of light multi-purpose oil
should be applied to the AEROBIC RIDER 2. Apply a few drops of
oil between the axle caps or acorn nuts and the frame in the loca-
tions shown at the right. Make sure to apply oil to both sides of the
AEROBIC RIDER 2.
Apply Oil
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CONDITIONING GUIDELINES
The following general guidelines will help you to plan
your exercise program. Remember that proper nutri-
tion and adequate rest are essential for successful
results.
gy. Only after the first few minutes of exercise does
your body begin to use stored fat calories for energy. If
your goal is to burn fat, adjust your pace until your
heart rate is near the lowest number in your training
zone as you exercise.
WARNING: Before beginning this or any exer-
cise program, consult your physician. This is
especially important for persons over the age
of 35 or persons with pre-existing health
problems.
Maximum Fat Burning
For increased fat burning, adjust your pace until your
heart rate is near the middle number in your training
zone as you exercise.
Aerobic Exercise
EXERCISE INTENSITY
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust your pace until your heart rate is near the high-
est number in your training zone.
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide.
The chart below shows recommended heart rates for
fat burning, maximum fat burning, and cardiovascular
(aerobic) exercise.
HOW TO MEASURE YOUR HEART RATE
To measure
your heart rate,
first exercise
for at least four
minutes. Then,
stop exercising
and place two
fingers on your
wrist as
shown. Take a
six-second
heartbeat
count, and multiply the result by 10 to find your heart
rate. For example, if your six-second heartbeat count
is 14, your heart rate is 140 beats per minute. (A six-
second count is used because your heart rate will
drop rapidly when you stop exercising.)
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, look above your age and
find the three numbers in light grey boxes. The three
numbers are your “training zone.” The lowest number
is the recommended heart rate for fat burning; the
middle number is the recommended heart rate for
maximum fat burning; the highest number is the rec-
ommended heart rate for aerobic exercise.
Adjust your pace until your heart rate is at the desired
level.
WORKOUT GUIDELINES
Each workout should include the following three parts:
Fat Burning
A warm-up, lasting 5 to 10 minutes. Begin with slow,
controlled stretches, and progress to more rhythmic
stretches to increase the body temperature, heart rate,
and circulation in preparation for strenuous exercise.
(Refer to SUGGESTED STRETCHES on page 13.)
To burn fat effectively, you must exercise at a relative-
ly low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for ener-
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Training zone exercise, consisting of 20 to 30 min-
utes of exercising with your heart rate in your training
zone. (See the chart on page 12 to find your training
zone.)
leave you relaxed and comfortably tired.
EXERCISE FREQUENCY
To maintain or improve your condition, plan three
workouts each week, with at least one day of rest
between workouts. After a few months of regular exer-
cise, you may complete up to five workouts each
week, if desired. The key to success is make exercise
a regular and enjoyable part of your everyday life.
A cool-down, with 5 to 10 minutes of stretching.
Thorough stretching offsets muscle contractions and
other problems caused when you stop exercising sud-
denly. Stretching for increased flexibility is also most
effective after exercising. A proper cool-down should
SUGGESTED STRETCHES
The correct form for several basic stretches is shown at the
right. Move slowly as you stretch—never bounce.
1
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward
from your hips. Allow your back and shoulders to relax as you
reach down toward your toes as far as possible. Hold for 15
counts, then relax. Repeat 3 times. Stretches: Hamstrings,
back of knees and back.
2
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot
toward you and rest it against the inner thigh of your extended
leg. Reach toward your toes as far as possible. Hold for 15
counts, then relax. Repeat 3 times for both legs. Stretches:
Hamstrings, lower back and groin.
3
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place
your hands against a wall. Keep your back leg straight and
your back foot flat on the floor. Bend your front leg, lean for-
ward and move your hips toward the wall. Hold for 15 counts,
then relax. Repeat 3 times for both legs. To cause further
stretching of the achilles tendons, bend your back leg as well.
Stretches: Calves, achilles tendons and ankles.
4
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and
grasp one foot with your other hand. Bring your heel as close
to your buttocks as possible. Hold for 15 counts, then relax.
Repeat 3 times for both legs. Stretches: Quadriceps and hip
muscles.
5
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees out-
ward. Pull your feet toward your groin area as far as possible.
Hold for 15 counts, then relax. Repeat 3 times. Stretches:
Quadriceps and hip muscles.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERING REPLACEMENT PARTS
The model number and serial number of your AEROBIC RIDER
2™ by HEALTHRIDER are listed on a decal attached to the frame.
See the front cover of this manual to find the location of the decal.
All replacement parts are available for immediate purchase or
special order when you visit your nearest SEARS Service Center.
To request service or to order parts by telephone, call the toll-free
numbers listed at the left.
QUESTIONS?
If you find that:
When requesting help or service, or ordering parts, please be
prepared to provide the following information:
• you need help assembling or
operating the AEROBIC RIDER 2
• The MODEL NUMBER of the product (831.287941).
• a part is missing
• The NAME of the product (AEROBIC RIDER 2™ by
HEALTHRIDER).
• or you need to schedule repair
service
• The PART NUMBER of the PART (see pages 14 and 15 of this
manual).
call our toll-free HELPLINE
1-800-736-6879
• The DESCRIPTION of the PART (see pages 14 and 15 of this
manual).
Monday–Saturday, 7 am–7 pm
Central Time (excluding holidays)
REPLACEMENT
PARTS
If parts become worn and need to
be replaced, call the following toll-
free number
1-800-FON-PART (366-7278)
FULL 90 DAY WARRANTY
For 90 days from the date of purchase, if failure occurs due to defect in material or workmanship in this
SEARS EXERCISER, contact the nearest SEARS Service Center throughout the United States and
SEARS will repair or replace the EXERCISER, free of charge.
This warranty does not apply when the EXERCISER is used commercially or for rental purposes.
This warranty gives you specific legal rights, and you may also have other rights which vary from state
to state.
SEARS, ROEBUCK AND CO., DEPT. 817WA, HOFFMAN ESTATES, IL 60179
HealthRider is a registered trademark of ICON Health & Fitness, Inc.
Part No. 153183 R0199A
Printed in USA © 1999 Sears, Roebuck and Co.
Download from Www.Somanuals.com. All Manuals Search And Download.
|