20 Series Recumbent Bike
Assembly Manual
Nautilus® Bowflex® Schwinn® Fitness Pearl Izumi® StairMaster® Universal® Nautilus Institute®
001-7214-010808A
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Warnings
This icon means a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Before using this equipment, obey the following warnings:
Read and understand the complete Owner's Manual.
Read and understand all Warnings on this machine.
•
•
•
Keep children away from this machine. Watch them closely when near the machine. Moving parts that appear
dangerous to adults may not appear so to children.
Consult a physician before starting an exercise program. Stop exercising if you feel pain or tightness in your chest,
become short of breath, or feel faint. Contact your doctor before using the machine again.
Examine this machine for loose parts or signs of wear. Pay special attention to the seat, pedals, and crank arms.
Contact Nautilus Customer Service for repair information. Use only genuine Schwinn® replacement parts supplied by
Nautilus.
•
•
•
•
•
•
This exercise machine is for consumer users only.
Set up and operate this exercise machine on a solid level surface.
Do not wear loose clothing or jewelry. This machine contains moving parts.
Maximum user weight limit: 275 lb. (125 kg). Do not use if you are over this weight
Stabilize the pedals before stepping on them and use caution when stepping off the machine.
Keep at least 19.7 inches (0.5 m) on each side of the machine clear. This is the recommended safe distance for access
and passage around and emergency dismounts from the machine.
•
Warn bystanders to keep a safe distance, at least 3 feet (1 m). Do not allow anyone to touch the operator while the
machine is in motion.
•
•
Keep the foot pedals clean and dry.
Do not over exert yourself during exercise. Operate the machine in the manner described in this manual.
3
Assembly Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Exploded Drawing
8
10
7
22
28
27
16
12
32
20
31
1
24
9
2
20
13
26
17
6
25
29
30
23
14
5
15
19
11
22
4
23
18
16
17
3
16
16
17
Note: Some component images are for general
reference only and may not represent the actual shape
or detail of the part. Assembly is unaffected.
4
Assembly Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
PARTS LIST
Ref.
Description
Qty
1
2
3
4
Main Frame
1
1
1
1
1
Front Stabilizer
Rear Stabilizer
Saddle Support Frame
Rail Tube
5
6
7
Handlebar
Saddle
1
1
8
9
Back Cushion
Pulse Wire Connector
Console (Computer)
Left Pedal
Right Pedal
Carriage Bolt M10 x 70mm
Acorn Nut M10
Arc Washer ID 10.5; OD 25mm; T 1.5mm
Hex Screw M8 x 15mm
Flat Washer ID 8.4mm; OD 25mm; T 1.5mm
Limit Rubber Pad
1
1
1
1
1
2
2
2
16
14
2
1
8
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
Crank
Phillips Screw M6 x 35mm
Not Used
Lower Pulse Wire (Contact Heart Rate wire)
Middle Pulse Wire (Contact Heart Rate wire)
Lower Computer Wire
Handlebar Wire Connector (CHR Electrode cable)
Hex Screw M8 x 10mm
Computer Wire Connector
Flat Head Phillips Screw M5 x 10mm
Adjustment Handlebar
1
1
1
1
4
1
4
1
1
1
4
Screw M5 x 10mm
Front Post
Arc Washer ID 8.5; OD 22mm; T 1.5mm
If you are missing items or have damaged components, please contact 800-NAUTILUS (628-8458) for replacements.
5
Assembly Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Guide
Ref.
13
14
15
16
17
18
20
26
30
32
Description
Qty
Carriage Bolt M10 x 70mm
Acorn Nut M10
2pcs
2pcs
Arc Washer ID 10.5mm; OD 25mm; T 1.5mm
Hex Screw M8 x 15mm
2 pcs
16pcs
14pcs
2pcs
8pcs
4pcs
1pc
Flat Washer ID 8.4mm; OD 16mm; T 1.5mm
Limit Rubber Pad
Phillips Head Screw M6 x 35mm
Hex Screw M8 x 10mm
Screw M5 x 10mm
Arc Washer ID 8.5mm; OD 22mm; T 1.5mm
4 pcs
Tools required
Hex Key L 6mm
1pc
1pc
1pc
Open End Wrench 15mm
Box Wrench 17mm x 13mm
You will also need the following tool (not provided):
Phillips screwdriver
6
Assembly Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Basic Assembly Principles
Here are a few basic tips that will aid in the assembly process. By using these principles, you can simplify each
process and save yourself extra time and effort.
1. To make the assembly process go faster, gather the pieces you need for each step and thoroughly read the
assembly instructions for that step prior to starting assembly for the step.
2. When attaching two pieces, gently lift and look through the bolt holes to help guide the bolt through the holes.
3. As a general rule, and for all bolts and nuts, turn bolts or nuts toward the right (clockwise) to tighten and left
(counterclockwise) to loosen.
7
Assembly Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Steps
Step 1: Install Front Stabilizers
1-1: Install Front Stabilizer (2) to Main Frame (1) using 2
Parts:
Carriage Bolts (13), 2 Arc Washers (15), and 2 Acorn
Nuts (14) as indicated (Figure 1).
• #2 - Front Stabilizer (Qty 1)
• #1 - Main Frame (Qty 1)
• #13 - Carriage Bolts (Qty 2)
• #15 - Arc Washers (Qty 2)
• #14 - Acorn Nut (Qty 2)
Tools:
Note: Position Front Stabilizer so arrow on decal is
pointing upwards (Figure 1A).
• Wrench
2
13
1
14
15
Figure 1
2
UP
Sticker
Figure
1A
8
Assembly Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Steps
Step 2: Assemble Saddle Support
Parts:
2-1: Slide Saddle Support Frame (4) onto Rail Tube (5) as
shown in Figure 2. The wires from the Rail Tube pass
through the Saddle Support Frame.
• #4 - Saddle Support Frame (Qty 1)
• #5 - Rail Tube (Qty 1)
Note: Do not cut or pinch the wires.
4
5
Figure
2
9
Assembly Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Steps
Step 3: Install RailTube Assembly to Main Frame
Parts:
• Main Frame Assembly (#1) from Step 1
3-1: Connect the Lower Pulse Wire (22) to the Middle Pulse
Wire (23) as shown in Figure 3A.
• Rail Tube Assembly (#5) from Step 2
• #16 - Hex Screw (Qty 6)
3-2: Slide the Rail Tube Assembly (5) onto the Main Frame
(1) and attach using 6 Hex Screws (16) and 6 Flat
Washers (17) as shown in Figure 3.
• #17 - Flat Washer (Qty 6)
• #18 - Limit Rubber Pad (Qty 2)
• #22 - Lower Pulse Wire (Qty 1)
• #23 - Middle Pulse Wire (Qty 1)
Note: Make sure to push Lower Pulse Wire (22) and
the Middle Pulse Wire (23) into the Main Frame
(1) connection bracket. Ensure the wires will
not be pinched or severed when assembling
the Rail Tube Assembly (5) to the Main Frame
(1).
Tools:
• Hex key L6
• Phillips screwdriver
3-3: Attach the 2 Limit Rubber Pads using 2 Hex Screws
(16). DO NOT overtighten screws.
22
23
Figure
3A
1
22
23
16
18
17
16
Figure 3
5
10
Assembly Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Steps
Step 4: Attach Rear Stabilizer Bar
Parts:
4-1: Attach the Rear Stabilizer Bar (3) to the Rail Tube (5)
using 4 Hex Screws (16) and 4 Flat Washers (17).
• #3 - Rear Stabilizer Bar (Qty 1)
• #5 - Rail Tube Assembly (Qty 1)
• #16 - Hex Screw (Qty 4)
• #17 - Flat Washer (Qty 4)
Tools:
Note: Make sure the Rear Stabilizer Bar (3) is
oriented as illustrated, with the bend in the
bar facing forward.
• Hex key L6
5
17
16
3
Figure 4
11
Assembly Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Steps
Step 5: Attach Handlebar to Saddle Support Frame
Parts:
• #4 - Saddle Support Frame (Qty 1)
5-1: Attach the Handlebar (6) to Saddle Support Frame
(4) using 4 Hex Screws (26) and 4 Flat Washers (17)
as shown in Figure 5.
• #6 - Handlebar (Qty 1)
• #17 - Flat Washer (Qty 4)
5-2: Connect Handlebar Wire Connector (25) to Middle
Pulse Wire (23) as shown in Figure 5A. Do not
pinch the Handlebar Wire Connector (25) during
assembly
• #26 - Hex Screws (Qty 4)
• #23 - Middle Pulse Wire (Qty 1)
• #25 - Handlebar Wire Connector (Qty 1)
Tools:
• Hex key L6
6
Figure 5
26
17
25
4
23
23
25
Figure
5A
12
Assembly Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Steps
Step 6: Attach Cushions
Parts:
6-1: Install Saddle (7) and Back Cushion (8) onto the
Saddle Support Frame (4) using 8 Phillips Screws
(20). Insert the Phillips Screws through the screw
holes in the Saddle Support Frame first when
attaching the Saddle and Back Cushion.
• #4 - Support Frame (Qty 1)
• #7 - Saddle (Qty 1)
• #8 - Back Cushion (Qty 1)
• #20 - Phillips Screw (Qty 8)
Tools:
Note: There are two groups of mounting holes
on the Back Cushion (8) so that you may
adjust the height of the back support to your
preference.
• Phillips Screw Driver
8
7
20
4
Figure 6
13
Assembly Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Steps
Step 7: Mount the Console
Parts:
7-1: Feed Lower Pulse Wire (22) and Lower Computer
Wire (24) through the Front Post (31).
• #22 - Lower Pulse Wire (Qty 1)
• #24 - Lower Computer Wire (Qty 1)
• #31 - Front Post (Qty 1)
7-2: Install the Front Post (31) onto the Main Frame (1),
using 4 Hex Screws (16) and 4 Arc Washers (32).
• #10 - Console (Qty 1)
7-3: Connect Lower Pulse Wire (22) to the Pulse Wire
Connector (9), and the Lower Computer Wire (24) to
the Computer Wire Connector (27).
• #9 - Pulse Wire Connector (Qty 1)
• #27 - Computer Wire Connector (Qty 1)
• #32 - Arc Washer (Qty 4)
• #16 - Hex Screw (Qty 4)
Note: Push the wires gently into the Front Post.
Do not cut or pinch the wires.
• #28 - Flat Head Phillips Screw (Qty 4)
7-4: Install the Console (10) to Front Post (31) using 4
Flat Head Phillips Screws (28) as shown in Figure
7A.
Tools:
• Hex key L6
28
10
16
10
32
22
22
27
9
31
24
9
27
24
1
28
Figure 7
Figure
7A
14
Assembly Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Steps
Step 8: Install Adjustment Handle
Parts:
8-1: Insert the Adjustment Handle (29) into the handle
mount (see Detail A). Finish install by tightening
Screw (30).
• #29 - Adjustment Handle (Qty 1)
• #30 - Screw (Qty 1)
Note: Do not overtighten and strip the threads on
the screw (30).
8-2: Remove cam retainer by cutting tie strap, and dis-
card. See Figure 8A.
30
Handle
mount
29
29
A
Detail A
30
Figure 8
29
(side view)
Cam retainer
Figure 8A
15
Assembly Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Steps
Step 9: Install Pedals
Parts:
9-1: Install the Left Pedal (11) to Left Crank (19). Install
Right Pedal (12) to the Right Crank.
• #11 - Left Pedal (Qty 1)
• #12 - Right Pedal (Qty 1)
• Batteries
Note: The Left Pedal has a left handed thread
and screws into the Left Crank counter-
clockwise.
Tools:
9-2: Insert 4 C batteries into the back of the console as
• Wrench L15
shown by the diagram in battery bay.
12
19
19
11
Figure 9
16
Assembly Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Steps
Step 10: Final Inspection
10-1: Tighten all hardware.
10-2: Read warnings on machine.
Please read and refer to the Owner’s Manual for:
•
•
•
Operating Instructions
Maintenance Instructions
Warranty Information.
Failure to visually check and test assembly before use can cause damage to the equipment.
It can also cause serious injury to users and bystanders.
17
Assembly Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Contact Information
UNITED STATES OFFICES:
INTERNATIONAL OFFICES:
For technical assistance and a list of distributors in your
area, please call or fax one of the following numbers.
E-mail: [email protected]
TECHNICAL/CUSTOMER SERVICE
Phone: 800-NAUTILUS (800-628-8458)
Fax: (877) 686-6466
INTERNATIONAL CUSTOMER SERVICE
Nautilus International S.A.
Rue Jean Prouvé
E-mail: [email protected]
1762 Givisiez / Switzerland
Tel: (41) (26) 460 77 77
Fax: (41) (26) 460 77 70
CORPORATE HEADQUARTERS
Nautilus, Inc.
E-mail: [email protected]
World Headquarters
16400 SE Nautilus Drive
Vancouver, Washington, USA 98683
Phone: (800) NAUTILUS (800) 628-8458
GERMANY and AUSTRIA
Nautilus Deutschland GmbH
Albin-Köbis-Str. 4
51147 Köln
Tel.: (49) 02203 2020 0
Fax: (49) 02203 2020 45 45
CANADA OFFICE:
NAUTILUS FITNESS CANADA, INC.
925 Keewatin Street
ITALY
Nautilus Italy S.r.l., Via della Mercanzia, 103
40050 Funo di Argelato - Bologna
Tel: (39) 051 664 6201
Winnipeg, MB, Canada R2X 2X4
Phone: (866) 381-5996
Fax: (800) 532-6934
Fax: (39) 051 664 7461
E-mail: [email protected]
SWITZERLAND
Nautilus Switzerland SA
Rue Jean-Prouvé 6,
CH-1762 Givisiez
Tel: (41) 026 460 77 66
Fax: (41) 026 460 77 60
UNITED KINGDOM
Nautilus UK Ltd
Nautilus UK, 4 Vincent Avenue,
Crownhill, Milton Keynes, Bucks, MK8 0AB
Tel: (44) 1908 267 345
Fax: (44) 1908 567 346
CHINA
Nautilus Representative Office
Nautilus, Shanghai, 7A No.728, Yan’an Rd(West)
200050 Shanghai, China
Tel: (86) 21 523 707 00
Fax: (86) 21 523 707 09
19
Assembly Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
©2008. Nautilus, Inc. All rights reserved. Nautilus, the Nautilus Logo, Universal, the Universal Logo, Bowflex, StairMaster, Pearl Izumi, Nautilus Institute and Active Series are either registered
trademarks or trademarks of Nautilus, Inc. Schwinn and the Schwinn Quality Seal are registered trademarks. All other trademarks are owned by their respective companies.
Nautilus, Inc., World Headquarters, 16400 SE Nautilus Drive, Vancouver, WA 98683 1-800-NAUTILUS www.nautilus.com
Printed in China
Nautilus®
Bowflex®
Schwinn® Fitness
Pearl Izumi®
StairMaster®
Universal®
Nautilus Institute®
Download from Www.Somanuals.com. All Manuals Search And Download.
|