Scag Power Equipment Lawn Mower GC STT CSV User Guide

MODEL GC-STT-CSV  
THIS MANUALCONTAINS THE OPERATING  
INSTRUCTIONS AND SAFETY INFORMA-  
TION FORYOUR SCAGACCESSORY. READ-  
ING THIS MANUAL WILL PROVIDE YOU  
WITH MAINTENANCE AND ADJUSTMENT  
PROCEDURES TO KEEPYOURACCESSORY  
PERFORMING TO MAXIMUM EFFICIENCY.  
THE SPECIFIC MODELS THAT THIS BOOK  
COVERS ARE CONTAINED ON THE INSIDE  
COVER. BEFORE OPERATING YOUR MA-  
CHINE, PLEASE READ ALL THE INFORMA-  
TION ENCLOSED.  
P A R T N U M B E R 0 3 1 8 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
A replacement manual is available from your  
authorized Scag Service Dealer or by contacting:  
Scag Power Equipment, Service Department at P.O.  
Box 152, Mayville, WI 53050. You may also contact  
manual for this grass catcher can be downloaded by  
using the model and serial number or use the contact  
form to make your request. Please indicate the  
complete model and serial number of your Scag  
product when requesting replacement manuals.  
1.1 INTRODUCTION  
This manual has been prepared to provide the  
information you need to correctly assemble, operate,  
and maintain this grass catcher. Read it carefully and  
keep it for future reference.  
The replacement of any part on this product by other  
than the manufacturer's authorized replacement part  
may adversely affect the performance, durability or  
safety of this product.  
USE OF OTHER THAN ORIGINAL SCAG  
REPLACEMENT PARTS WILL VOID THE  
WARRANTY.  
WARNING  
DO NOT OPERATE WITHOUT DISCHARGE CHUTE, MULCHING  
KIT, OR ENTIRE GRASS CATCHER INSTALLED  
If additional information or service is needed that is  
not outlined in this manual, please contact your Scag  
Power Equipment dealer. Scag dealers are trained in  
the latest service methods and carry a full line of Scag  
replacement parts.  
2. Before dumping the debris, disengage the  
mower, stop the engine and wait for all  
movement to stop.  
3. ALWAYS turn the engine OFF, remove the key  
and wait for all movement to stop before  
servicing or cleaning the mower or the grass  
catcher.  
When ordering parts, always provide the complete  
model number of your catcher.  
All information provided in this manual is based upon  
information available at the time of printing. Scag  
Power Equipment reserves the right to make changes  
at any time without notice or obligation.  
DANGER  
ROTATING BLOWER  
BLADES  
1.2 DIRECTION REFERENCE  
STOP ENGINE BEFORE  
ENTERING CHUTE  
The "Right" and "Left", "Front" and "Rear" of the  
machine are referenced from the normal operating  
position.  
CONTACT CAN INJURE  
2.1 SAFETY AND OPERATING  
INSTRUCTIONS  
4. Do not modify or alter any component of the  
grass catcher attachment or mower.  
5. Do not allow any passengers to ride on the grass  
catcher attachment or on the mower.  
-NOTE-  
To avoid personal injury, it is imperative that  
all safety instructions be observed.  
2.2 GRASS CATCHING OPERATION  
1. Read this operator's manual and the  
operator's manual that is supplied with the  
machine this attachment is used on.  
1. With the hopper door closed, engage the deck  
drive.  
2. Proceed to mow until the hopper is full.  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. To clean the hopper debris screen;  
3. When dumping the hopper into a disposal area:  
A. Disengage the deck drive and allow all  
moving parts to come to a complete stop.  
WARNING  
DO NOT DUMP CLIPPINGS IN A DISPOSAL AREA THAT IS  
BURNING  
B. Apply parking brake and shut off the engine.  
A. Disengage the deck drive, apply the parking  
brake and allow all moving parts to come to  
a complete stop.  
C. Stand on the left side of the hopper  
assembly.  
D. Unhook the debris screen latches and  
remove the debris screen from the hopper.  
See Figure 2-3.  
B. Pull downward on the hopper door handle to  
allow the hopper sweeper to remove the  
material from inside the hopper. See Figure  
2-1.  
Debris Screen  
Latches  
Figure 2-3 GC-CS  
FIGURE 2-3  
FIGURE 2-1  
E. Remove material from the debris screen and  
reinstall. Secure by latching the debris  
screen latches.  
C. Once the material has been completely  
removed from the hopper, lift the hopper  
door handle to close the hopper door and  
lock into place. See Figure 2-2.  
6. When service is needed inside the hopper,  
disengage the deck drive and allow all moving  
parts to come to a complete stop, shut off the  
engine and apply the parking brake. Rotate the  
hopper door prop rod upward until it contacts the  
hopper door. This will prevent the hopper door  
from moving until the service is complete. See  
Figure 2-4.  
LOCK  
FIGURE 2-2  
Hopper Prop  
Rod  
4. When dumping the hopper into a disposal area,  
inspect the hopper debris screen for material.  
When the debris screen is full of material, the  
grass catching ability may suffer. Frequency of  
cleaning the hopper debris screen will vary  
dependingonconditions.  
Figure 2-4 GC-CS  
FIGURE 2-4  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
3.1 ASSEMBLY INSTRUCTIONS  
3. Remove the right side belt cover to gain access  
to the spindle assembly. Remove the u-nuts  
from the cutter deck bracket. See Figure 3-1.  
-NOTE-  
Use the illustrated parts list as a part number  
reference when following the assembly  
instructions.  
4. Install the grass catcher pulley onto the spindle  
assembly. Apply loctite to both pulley setscrews  
and tighten. See Figure 3-1.  
1. Remove all packaging materials. Lay out the  
mounting hardware and the catcher assembly  
parts for easy access. Prepare the work area  
making sure that it is a clean, safe environment.  
5. Remove the "Custom-Cut" and "Turbo" baffles  
from the cutter deck. Using the original  
hardware, install the new "Front" and "Turbo"  
baffles. See Figure 3-2.  
2. Remove the discharge chute from the cutter  
deck. See Figure 3-1.  
Front Baffle  
52V - 424402  
61V - 424403  
INSTALL PULLEY  
ON RH SPINDLE SHAFT -  
ON TOP OF EXISTING  
SPINDLE DRIVE  
Turbo Baffle  
52V - 424211  
61V - 424212  
REMOVE DISCHARGE  
CHUTE AND  
REMOVE EXISTING  
RT. SIDE BELT  
COVER  
PULLEY  
HARDWARE  
UNDER SIDE OF  
VELOCITY-PLUS  
CUTTER DECK SHOWN  
REMOVE (2)  
U-NUTS  
FIGURE 3-2  
RIGHT SIDE OF 52"  
CUTTER DECK SHOWN  
-NOTE-  
(Note: Some parts not shown for viewing purposes.)  
Do not discard the original "Custom-Cut"  
or "Turbo" baffles. These baffles may be  
reinstalled anytime the grass catcher has  
been removed from the machine.  
FIGURE 3-1  
-NOTE-  
Do not discard the discharge chute or  
mounting hardware. The discharge chute  
MUST be reinstalled anytime the grass  
catcher has been removed from the machine.  
6. Install the blower mounting bracket to the deck  
using 1/2-13 x 1-1/2" hex head bolts (p/n 04001-  
71), 1/2" spring lockwashers (p/n 04030-06), and  
1/2-13 elastic stop nuts (p/n 04021-07). See  
Figure 3-3, Page 4. Do not fully tighten the  
hardware at this time.  
WARNING  
7. This step is for 52" cutter decks only.  
Block the right front side on the cutter deck and  
remove the hang chain. Install the deck lift link.  
Secure using hex head bolts (p/n 04001-32,  
04001-20), flatwashers (p/n 04041-07), spacers  
(p/n 43212), and serrated flange nuts (p/n 04019-  
04). See Figure 3-3, page 3.  
DO NOT OPERATE WITHOUT DISCHARGE CHUTE, MULCHING  
KIT, OR ENTIRE GRASS CATCHER INSTALLED  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
52" Cutter Deck  
LIFT LINK  
BELL CRANK  
NUT  
SPACER  
BOLT, 3/8-16  
x 1-1/4"  
BOLT, 3/8-16  
x 1-1/2"  
WASHER  
SPACER  
NUT  
CUTTER DECK  
REAR OF  
FRONT OF  
CUTTER DECK  
CUTTER DECK  
DISCHARGE CHUTE OPENING  
VIEW FROM RIGHT SIDE  
OF CUTTER DECK  
Figure 2-52"GC-STT install art  
61" & 72" Cutter Decks  
PROPERYL  
SECREVI  
ENGEI  
WTHI  
OLI  
AND  
REAR OF  
CUTTER DECK  
FRONT OF  
CUTTER DECK  
DISCHARGEFUCELH.UTE OPENING  
VIEW FROM RIGHT SIDE  
OF CUTTER DECK  
Figure 2-61"GC-STT install art  
FIGURE 3-3  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
11. Install the belt to the spindle pulley. When  
replacing the belt, see figure below.  
8. Install the blower assembly to the mounting  
bracket and secure with the mounting pin and  
hair pin. See Figure 3-4.  
BACK SIDE  
IDLER PULLEY  
BLOWER  
PULLEY  
9. Align the blower assembly with the discharge  
opening of the cutter deck. Tighten the  
hardware for the mounting bracket. Install the  
quick pin through the rear hole in the discharge  
chute mounting bracket. See Figure 3-4.  
10. Install the new belt cover from the cutter deck to  
the blower mounting bracket and secure with the  
original belt cover plastic wing nuts.  
SPINDLE  
PULLEY  
FRONT SIDE  
IDLER PULLEY  
12. Install the plastic belt cover and secure with the  
plastic wing nuts. See Page 12 of the Illustrated  
Parts List for proper installation.  
BLOWER  
ASSEMBLY  
QUICK  
PIN  
HAIR  
PIN  
MOUNTING  
BRACKET  
MOUNTING PIN  
TIGHTEN MOUNTING  
BRACKET HARDWARE  
RIGHT SIDE OF  
CUTTER DECK SHOWN  
(Note: Some parts not shown for viewing purposes.)  
2006 GC-STC-V install art 3  
FIGURE 3-4  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
13. Install the hopper mounting brackets (p/n 451512 17. Install the weight support bar to the front of the  
& p/n 451595) to the outside of the frame on the  
rear of the machine using 3/8-16 x 1" hex head  
bolts (p/n 04001-19) and 3/8-16 elastic stop nuts  
(p/n 04021-09). See Figure 3-7, Page 7.  
machine by resting it directly on top of the caster  
support arms and sliding it tight against the frame  
of the machine. Secure the weight bar to the  
machine using (2) bar clamps, (4) 3/8-16 x 1-1/2"  
bolts and (4) 3/8-16 elastic stop nuts. See Figure  
3-6.  
14. Install the catcher support bracket onto the rear  
of the machine and secure with 5/16-18 x 1"  
carriage bolts (p/n 04003-04) and 5/16-18  
serrated flange nuts (p/n 04019-03) See Figure  
3-5.  
18. Install the weight assemblies to the weight  
support bar and secure them to the bar using the  
1/2"x 6-1/4" pin and lanyard. See Figure 3-6.  
Catcher Support Bracket  
WEIGHT (5x)  
LANYARD  
PIN  
ELASTIC STOP  
NUT  
BAR CLAMP  
BOLT  
WEIGHT SUPPORT BAR  
2002 GC-STT Install Art 3-5  
FIGURE 3-5  
FIGURE 3-6  
15. With the help of an assistant, install the hopper  
assembly into the hopper mounting brackets.  
See Figure 3-7, Page 7.  
19. Operate and test.  
16. Install the hose from the blower assembly to the  
hopper assembly. Secure using the 8-1/2"  
clamps.  
-NOTE-  
When installing this catcher on machines  
equipped with an air cooled engine the  
discharge hose should be shortened to  
56" in length.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Item #  
Part #  
Description  
1
2
3
4
5
04001-19  
04021-09  
04066-03  
423670  
451512  
451595  
Bolt, Hex Head 3/8-16 x 1"  
Nut, Elastic Stop 3/8-16  
Quick Pin  
Spacer, Hitch  
Hitch Bracket Weldment  
Hitch Bracket Weldment, Floating  
Hopper  
Assembly  
5
1
2
3
Liquid  
Cooled  
Only  
2
1
4
1
Note:  
2
Illustration is for reference only. Some parts have been  
removed for visual purposes and may vary depending  
on model.  
Frame  
3
5
FIGURE 3-7  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
6.1 GRASS CATCHER REMOVAL  
INSTRUCTIONS  
1. Prepare the work area making sure that it is a  
clean, safe environment.  
REMOVE  
2. Remove the rubber strap holding the adapter to  
the blower assembly. See Figure 5-1.  
3. Remove the belt from the spindle pulley and the  
quick pin securing the blower to the discharge  
mountingbracket.  
REMOVE  
4. Remove the pin and hair pin securing the blower  
assembly to the mounting bracket on the cutter  
deck and remove the blower assembly. See  
Figure 5-1.  
FIGURE 5-2  
6. With the help of an assistant, remove the hopper  
assembly.  
ADAPTER  
BLOWER  
7. Remove the front weights by removing the quick  
pins.  
ASSEMBLY  
QUICK PIN  
8. Re-install the side discharge chute to the opening  
on the cutter deck. Replace the two (2) outside  
mounting bolts on the discharge chute with the  
clevis pins (p/n 04064-15) and rue cotter pins  
(p/n 04069-03). See Figure 5-3.  
PIN & HAIR PIN  
MOUNTING  
BRACKET  
9. Re-install the cutter deck belt cover.  
DISCHARGE  
CHUTE  
RIGHT SIDE OF  
CUTTER DECK SHOWN  
2006 GC-STC-V removal art 1  
(Note: Some parts not shown for viewing purposes.)  
FIGURE 5-1  
CLEVIS PIN  
P/N 04064-15  
5. Remove the two (2) pins holding the hopper  
assembly to the mounting brackets on the rear of  
the machine. See Figure 5-2.  
CLEVIS PIN  
P/N 04064-15  
RUE COTTER PIN  
P/N 04069-03  
GC-STC-V removal art 3  
FIGURE 5-3  
WARNING  
DO NOT OPERATE WITHOUT DISCHARGE CHUTE, MULCHING  
KIT, OR ENTIRE GRASS CATCHER INSTALLED  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
5.1 MAINTENANCE CHART - RECOMMENDED SERVICE INTERVALS  
HOURS  
Break-In 8 20 40 100 200 500 Procedure  
(First 10)  
Comments  
X
X
X
X
Check all hardware for tightness  
Inspect hose and adapter  
Check belt for proper alignment  
Inspect fabric bags  
X
X
X
X
X
*Check screen in hopper  
Inspect hose and adapter  
Inspect fabric bags  
Remove debris from screen  
Check condition of blower  
*Apply grease to blower bearings  
Check belt for proper alignment  
See figure below  
X
* Perform these maintenance procedures more frequently under extreme dusty or dirty conditions.  
GREASE FITTING  
ON BEARING HOUSING  
GREASE FITTING  
ON BEARING HOUSING  
BEHIND PULLEY  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
GC-STT-V BLOWER HOUSING ASSEMBLY  
9
10  
11  
12  
8
48  
14  
11  
49  
4
1
2
50  
13  
9
11  
7
10  
47  
10  
14  
44  
27  
14  
11  
12  
15  
43  
16  
42  
41  
14  
17  
26  
39  
40  
18  
34  
15  
17  
19  
3
25  
28  
20  
21  
41  
5
38  
22  
23  
17  
35  
27  
24  
14  
46  
R
D
O
T
A
B
A
T
N
S
I
24  
14  
t
N
o
G
W
p
G
e
n
E
R
g
B
i
n
L
D
e
U
O
A
D
D
b
N
I
N
e
f
S
L
C
E
O
o
r
H
S
T
E
e
A
S
O
P
E
S
c
S
R
G
l
G
e
A
R
a
n
E
A
R
G
A
in  
N
D
U
S
T
g
E
A
C
o
r
R
A
M
O
H
E
D
T
r
e
L
C
W
E
m
I
S
O
o
v
i
I
N
R
R
S
n
g
T
O
A
R
E
L
R
L
E
D
29  
6
30  
33  
32  
37  
31  
31  
45  
47  
2005 GC V+ Blower Assembly  
45  
35 34  
36  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GC-STT-V BLOWER HOUSING ASSEMBLY  
Ref.  
No.  
Part  
Number  
Ref.  
No.  
Part  
Number  
Description  
Description  
1
2
3
4
5
6
7
8
04067-07  
481547  
04019-02  
04001-59  
481377  
482080  
481428  
483223  
04024-02  
04021-05  
04041-07  
43277  
483173  
483209  
04021-09  
04030-04  
424361  
04003-05  
04001-54  
04001-81  
04001-21  
461xxx  
Pin, Ring 2-1/4" Long  
Lanyard, Deck Height Pin  
Nut, Serr. Flange 1/4-20  
Bolt, Hex Head 1/4-20 x 1-1/4"  
Decal, Blower  
Decal, Rotating Blower  
Grip, Blower Lever  
Cap, Square  
Nut, Push On 3/8 Thread  
Lock Nut, 3/8-16  
Flatwasher, 3/8-.391 x .938 x .105  
Spacer  
Pulley, Idler 3-1/2" Dia. - 52"  
Pulley, Idler 4" Dia. - 61"  
Nut, Elastic Stop 3/8-16  
Lockwasher, 3/8-16  
Plate, Catcher Mounting  
Bolt, Carr. 3/8-16 x 1-1/2"  
Bolt, Hex Head 3/8-16 x 3" - 52"  
Bolt, Hex Head 3/8-16 x 3-1/2"  
Bolt, Hex Head 3/8-16 x 1-3/4"  
Idler Arm Assembly - 52"  
Idler Arm Assembly - 61"  
Belt, GC-STC  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
46  
47  
04019-04  
Nut, Serr. Flange 3/8-16  
04001-136 Bolt, Hex Head 3/8-16 x 1-1/2 Gr. 8  
483037  
461931  
04003-12  
04063-06  
461796  
483034  
04021-10  
461930  
421319  
48136-02  
48135-14  
482298  
04012-04  
461932  
481522  
43212  
04019-03  
461723  
451822  
451821  
04062-04  
424367  
04066-04  
Decal, Danger  
Blower Housing Weldment w/Decals  
Bolt, Carr. 5/16-18 x 3/4" Gr. 5  
Key, 1/4 x 1/4 x 1-1/2"  
Fan Weldment  
Bearing Assembly  
Nut, Elastic Stop 5/16-18  
Blower Housing Assembly, GC-STT  
Cover, Blower Housing  
Clamp, 8-5/8" Max Dia.  
Hose, 8.00" Dia. x 60.50" Long  
Pulley, 4-3/4" O.D. - 1" Bore  
Set Screw, 5/16-18 x 3/8"  
Frame, Blower Mount  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
Spring, Main Drive  
Spacer  
Nut, Serr. Flange 5/16-18  
Adapter w/Strap  
Receiver Weldment, Mount Post - 52"  
Receiver Weldment, Mount Post - 61"  
Hair Pin Cotter, .177 x 3-1/4"  
Dust Shield  
461928  
483182  
483189  
04043-04  
43504  
48  
49  
50  
22  
23  
24  
25  
Pulley, 3-1/2" O.D., GC-STC  
Washer, 3/8 Hardened  
Pivot, Idler Long - 52"  
Pivot, Idler - 61"  
Quick Pin, 5/16" Dia.  
43575  
26  
482871  
481039  
Decal, Belt Cover - 52"  
Decal, Belt Cover - 61"  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GC-STT-V BLOWER MOUNTING COMPONENTS  
UNDER SIDE OF  
VELOCITY-PLUS  
CUTTER DECK SHOWN  
16  
16  
10  
10  
11  
5
23  
2
26  
27  
23  
25  
4
6
7
28  
1
24  
26  
8
3
25  
25  
6
24  
13  
9
12  
21  
14  
15  
15  
22  
20  
16  
18  
17  
19  
RIGHT SIDE OF  
CUTTER DECK SHOWN  
2006 GC-STC-V BMC  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GC-STT-V BLOWER MOUNTING COMPONENTS  
Ref. Part  
No. Number  
Description  
1
483225  
483227  
Belt Cover, GC-STT - 52"  
Belt Cover, GC-STT - 61"  
2
3
04029-04  
483223  
Wingnut, Plastic 3/8" Small  
Cap, Square Vinyl  
4
5
6
7
8
9
10  
11  
12  
13  
14  
04021-08  
461723  
Nut, Elastic Stop 1/4-20  
Adapter, Blower GC-STT, includes item #7  
Flatwasher, 1/4-.312 x .750 x .065  
Rubber Strap 7-3/4"  
Bolt, Hex Head 1/4-20 x 1-1/4"  
Knob W/Stud, 3/8-16 x 1-1/4"  
Clevis Pin, 5/16 x 1-1/2"  
Pin, Rue Cotter 5/16 Dia.  
Pin, Ring 1/2 x 2-1/4"  
04040-14  
48137-04  
04001-59  
481625-01  
04064-15  
04069-03  
04067-07  
481547  
Lanyard  
482587  
482377  
Pulley, 4-1/2" for 52" Deck  
Pulley, 5-1/2" for 61" Deck  
Setscrew, 5/16-18 x 3/8"  
Nut, Elastic Stop 3/8-16  
Lockwasher, 3/8"  
Flatwasher, 3/8-.391 x .938 x .105  
Bolt, Carr. 3/8-16 x 1-1/4" Grade 5  
Mounting Post Weldment, Blower - 52"  
Mounting Post Weldment, Blower - 61"  
Belt Cover, GC-STT-52V  
Belt Cover, GC-STT-61V  
U-Nut  
Bolt, Carriage 3/8-16 x 1"  
Bolt, Hex Head 5/16-18 x 1"  
Flatwasher, 5/16-.375 x .875 x .083  
Nut, Elastic Stop 5/16-18  
Baffle, Front 52" Deck  
15  
16  
17  
18  
19  
20  
04012-04  
04021-09  
04030-04  
04041-07  
04003-11  
461418  
461894  
423427  
424329  
04110-03  
04003-23  
04001-09  
04040-15  
04021-10  
424402  
21  
22  
23  
24  
25  
26  
27  
424403  
Baffle, Front 61" Deck  
28  
424211  
Baffle, Turbo 52" Deck  
424212  
Baffle, Turbo 61" Deck  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GC-STT-CSV HOPPER COMPONENTS  
16  
14  
49  
50  
5
4
3
45  
45  
41  
15  
31  
11  
43  
51  
17  
56  
55  
40  
58  
59  
8
12  
9
25  
29  
6
33  
37  
34  
10  
53  
2
50  
49  
34  
B
49  
42  
24  
55  
27  
43  
49  
6
53  
61  
48  
60  
36  
18  
38  
19  
38  
53 C  
49  
34  
12  
49  
50  
52  
20  
54  
72  
49  
41  
49  
49  
18  
24  
49  
53  
53  
60  
70  
7
A
61  
62  
66  
49  
21  
58  
33  
59  
28  
1
10  
34  
38  
32  
49  
57  
46  
69  
30  
49  
45  
49  
38  
38  
35  
22  
49  
37  
13  
33  
36  
25  
49  
49  
21  
38  
C
23  
20  
33  
53  
26  
58  
32  
40  
44  
49  
49  
67  
19  
B
59  
46  
64  
49  
53  
A
63  
61  
29  
46  
26  
58  
59  
60  
57  
35  
28  
49  
49  
61  
65  
71  
46  
37  
68  
37  
60  
2006 GC-STT-CSV Hopper  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GC-STT-CSV HOPPER COMPONENTS  
Ref.  
No.  
Part  
Number  
Ref.  
No.  
Part  
Number  
Description  
Description  
1
2
3
4
5
6
7
8
483038  
482732  
461626  
482777  
04090-02  
423834  
423938  
423849  
423850  
423858  
423837  
423840  
451838  
451601  
451602  
451603  
451607  
43631  
423830  
423828  
422386  
423862  
423864  
43063  
43282  
43277  
481309  
43641  
43640  
Hopper, GC-STT-CS  
Door, GC-CS  
Sweeper Weldment, GC-CS  
Pad, Rubber  
Pop Rivet, 3/16 x .652  
Plate, Stiffener  
Support Frame, Hopper  
Hinge Bracket, L.H.  
40  
41  
42  
43  
44  
45  
46  
47  
48  
49  
50  
51  
52  
53  
54  
55  
56  
57  
58  
59  
60  
61  
62  
63  
64  
65  
66  
67  
68  
69  
04001-77  
04003-04  
04010-01  
04017-16  
04017-17  
04019-03  
04019-04  
04020-12  
04021-01  
04021-09  
04021-10  
04032-01  
04040-15  
04041-07  
43642  
04001-54  
451598  
04066-03  
481538  
04020-26  
481539  
04020-25  
423865  
04001-19  
04021-09  
451512  
451595  
04001-51  
423690  
423855  
423859  
423836  
451596  
Bolt, Hex Head 3/8-16 x 3-1/2"  
Bolt, Carriage 5/16-18 x 1"  
Screw, #10-32 x 1/2"  
Cap Screw, 5/16-18 x 3/4" Serr. Flan.  
Cap Screw, 5/16-18 x 1" Serr. Flan.  
Nut, 5/16-18 Serrated Flange  
Nut, 3/8-16 Serrated Flange  
Nut, 3/8-16 UNC Jam  
Nut, #10-32 Elastic Stop  
Nut, 3/8-16 Elastic Stop  
Nut, 5/16-18 Elastic Stop  
Washer, Special Wave  
Washer, 5/16-.375 x .875 x .083 Flat  
Washer, 3/8-.931 x .938 x .105 Flat  
Bushing, Hopper Latch GC-CS  
Bolt, Hex Head 3/8-16 x 3"  
Hinge Weldment, Door  
9
Hinge Bracket, R.H.  
Bracket, Hopper Support  
Latch, Door Prop  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
Plate, Latch  
Bellcrank Weldment, Upper  
Debris Screen Weldment  
Screen Support Weldment, Rear  
Screen Support Weldment, Front  
Hinge Weldment, Hopper  
Spacer  
Brace Stiffener, Short  
Tube, Upright  
Brace, Engine Mount  
Latch, Dump Rod Inner  
Latch, Dump Rod Outer  
Spacer  
Spacer  
Spacer  
Latch, Hood  
Linkage Assembly, Lower  
Linkage Assembly, Upper  
Knob  
Bolt, Hex Head 5/16-18 x 1-1/4  
Bolt, Hex Head 3/8-16 x 3/4"  
Bolt, Hex Head 3/8-16 x 1"  
Bolt, Hex Head 3/8-16 x 1-1/2"  
Bolt, Hex Head 3/8-16 x 1-3/4"  
Bolt, Hex Head 3/8-16 x 1-1/4"  
Bolt, Hex Head 3/8-16 x 2"  
Bolt, Hex Head 3/8-16 x 2-1/4"  
Bolt, Hex Head 5/16-18 x 3-1/2"  
Pin  
Rod End Male, 3/8-24 L.H. Thread  
Nut, 3/8-24 UNF L.H. Thread  
Rod End Male, 3/8-24 R.H. Thread  
Nut, 3/8-24 UNF R.H. Thread  
Alignment Bracket, GC-CS  
Bolt, Hex Head 3/8-16 x 1"  
Nut, 3/8-16 Elastic Stop  
Hitch Bracket Weldment  
Hitch Bracket Weldment, Floating  
Bolt, Hex Head 3/8-16 x 3-3/4"  
Support Bracket, Catcher  
Bracket, Lower Stiffener  
Backing Plate, Hopper (Not Shown)  
Retainer Strip, Hopper  
481245  
04001-10  
04001-18  
04001-19  
04001-20  
04001-21  
04001-32  
04001-45  
04001-46  
04001-63  
70  
71  
Frame Weldment  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GC-STT-CSV DECALS  
481039  
482275  
483044  
481327  
481377  
483037  
482080  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LIMITED WARRANTY- COMMERCIAL ACCESSORY  
AnypartoftheScagcommercialaccessorymanufacturedbyScagandfound,inthereasonablejudgmentofScag,  
tobedefectiveinmaterialorworkmanship,willberepairedorreplacedbyanAuthorizedScagServiceDealerwithout  
charge for parts and labor.  
The Scag accessory, including any defective part, must be returned to an Authorized Scag Service Dealer within  
the warranty period. The expense of delivering the accessory to the dealer for warranty work and the expense of  
returningitbacktotheownerafterrepairorreplacementwillbepaidforbytheowner. Scag’sresponsibilityinrespect  
toclaimsislimitedtomakingtherequiredrepairsorreplacements,andnoclaimofbreachofwarrantyshallbecause  
for cancellation or rescission of the contract of sale of any Scag machine. Proof of purchase will be required by the  
dealer to substantiate any warranty claim. All warranty work must be performed by an Authorized Scag Service  
Dealer.  
This warranty is limited to 90 days from the date of original retail purchase for any Scag accessory that is used for  
commercial purposes, or any other income-producing purpose including rental use.  
This warranty does not cover any accessory that has been subject to misuse, neglect, negligence, or accident, or  
thathasbeenoperatedinanywaycontrarytotheoperating instructionsasspecifiedintheOperator'sManual. The  
warranty does not apply to any damage to the accessory that is the result of improper maintenance, or to any  
accessory or parts that have not been assembled or installed as specified in the Operator's Manual.  
The warranty does not cover any accessory that has been altered or modified. In addition, the warranty does not  
extend to repairs made necessary by normal wear, or by the use of parts or accessories which, in the reasonable  
judgment of Scag, are either incompatible with the Scag mower or adversely affect its operation, performance or  
durability. This warranty does not cover engines and electric starters, which are warranted separately by their  
manufacturer.  
ScagPowerEquipmentreservestherighttochangeorimprovethedesignofanyaccessorywithoutassumingany  
obligation to modify any accessory previously manufactured.  
All other implied warranties are limited in duration to the 90 day warranty period. Accordingly, any such implied  
warranties including merchantability, fitness for a particular purpose, or otherwise, are disclaimed in their entirety  
after the expiration of the appropriate ninety day warranty period. Scag’s obligation under this warranty is strictly  
andexclusivelylimitedtotherepairorreplacementofdefectivepartsandScagdoesnotassumeorauthorizeanyone  
toassumeanyotherobligationforthem. Somestatesdonotallowlimitationsonhowlonganimpliedwarrantylasts,  
so the above limitation may not apply to you.  
Scagassumesnoresponsibilityforincidental,consequentialorotherdamagesincluding,butnotlimitedto,expense  
forgasoline,oil,expenseofdeliveringthemachinetoanAuthorizedScagServiceDealerandexpenseofreturning  
it back to the owner, mechanic’s travel time, telephone or telegram charges, rental of a like product during the time  
warranty repairs are being performed, travel, loss or damage to personal property, loss of revenue, loss of use of  
the mower, loss of time, or inconvenience. Some states do not allow the exclusion or limitation of incidental or  
consequential damages, so the above limitation or exclusion may not apply to you.  
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
© 2005  
PART NO. 03187  
PRINTED 7-2005  
PRINTED IN USA  
SCAG POWER EQUIPMENT  
DIVISION OF METALCRAFT OF MAYVILLE, INC  
Download from Www.Somanuals.com. All Manuals Search And Download.  

QSC Audio Speaker MD S215 User Guide
Q See Medical Alarms QSTD5304 User Guide
Radio Shack Surge Protector 61 2341 User Guide
Regency Indoor Fireplace P48 LP User Guide
Roper Washer RAB2121P User Guide
Rosewill Network Card RC 209 User Guide
Sabrent Computer Drive USBDSC5 User Guide
Salton Hot Beverage Maker GK 1202 User Guide
Seagate Server 73LP User Guide
Sears Treadmill 831297452 User Guide