INSTRUCTION MANUAL
BASICS
VPC-X1220EX
VPC-X1250
VPC-X1220GX
VPC-X1220PX
Digital Camera
Important note
This manual explains how to safely operate the VPC-X1220EX, VPC-X1250,
VPC-X1220GX and VPC-X1220PX.
Any information regarding only one of these products will be labeled as such.
Please read these instructions carefully before using the camera.
Make sure to read and understand the separate booklet “SAFETY MANUAL”.
Keep this manual in a safe place for later reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
FOR USERS IN THE USA
About the battery charger
IMPORTANT SAFETY
INSTRUCTIONS – SAVE THESE
INSTRUCTIONS
DANGER – TO REDUCE THE RISK
OF FIRE OR ELECTRIC SHOCK,
CAREFULLY FOLLOW THESE
INSTRUCTIONS
h For connection to a supply not in the U.S.A., use an attachment plug
adapter of the proper configuration for the power outlet.
h Power Supply Cord:
Use UL Listed detachable power supply cord - No. 18 AWG, two
conductors, rated 10 A, VW-1, 105 ºC, 125/250 V, minimum 1.8 m,
maximum 3 m long. Provided with a molded-on, non-polarized attachment
plug with a 15 A, 250 V (NEMA 2-15P) configuration or a 15 A, 125 V
(NEMA 1-15P) configuration and a molded-on connector which mates with
the Power Inlet.
Cord Type
Basic Cord Type
Other Suitable Types
TST
TS
SP-2
SP-3
SV
SPE-2, SPT-2
SPE-3, SPT-3
SVE, SVO, SVOO, SVT, SVTO, SVTOO
SJE, SJO, SJOO, SJT, SJTO, SJTOO
SE, SO, SOO, ST, STO, STOO
SJ
S
h This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
English
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
PARA LOS USUARIOS DE EE.UU.
Acerca del cargador de baterías
INSTRUCCIONES IMPORTANTE
SOBRE DE SEGURIDAD - GUARDE
ESTAS INSTRUCCIONES
PELIGRO - PARA REDUCIR EL
RIESGO DE INCENDIO O
DESCARGAS ELÉCTRICAS, SIGA
CUIDADOSAMENTE ESTAS
INSTRUCCIONES
h Para la conexión a una red de alimentación que no sea de EE.UU., utilice
el adaptador de enchufe apropiado para la toma de la red.
h Cable de alimentación:
Utilice el cable de alimentación UL desenchufable indicado en la lista - N.°
18 AWG, dos conductores, amperaje nominal de 10 A, VW-1, 105 ºC, 125/
250 V, mínimo 1,8 m, máximo 3 m de longitud. Provisto de enchufe
moldeado, adaptador de enchufe no polarizado con configuración de 15 A,
250 V (NEMA 2-15P), o configuración de 15 A, 125 V (NEMA 1-15P) y
conector moldeado que se adapta a la toma de corriente de la red.
Tipo de cable
Tipo de cable básico
Otros tipos adecuados
TST
TS
SP-2
SP-3
SV
SPE-2, SPT-2
SPE-3, SPT-3
SVE, SVO, SVOO, SVT, SVTO, SVTOO
SJE, SJO, SJOO, SJT, SJTO, SJTOO
SE, SO, SOO, ST, STO, STOO
SJ
S
h Este dispositivo cumple con lo estipulado en la Parte 15 de las Normativas
de la FCC. La operación está sujeta a las dos condiciones siguientes: (1)
este dispositivo no puede provocar interferencias nocivas, y (2) este
dispositivo debe aceptar las interferencias recibidas, incluidas las
interferencias que puedan provocar un funcionamiento no deseado.
iii English
Download from Www.Somanuals.com. All Manuals Search And Download.
kFOR CANADIAN USERS
i This Class B digital apparatus complies with Canadian ICES-003.
kFOR EU USERS
The symbol mark and recycling systems described below apply to EU
countries and do not apply to countries in other areas of the world.
Your SANYO product is designed and manufactured with high quality
materials and components which can be recycled and/or reused.
The symbol mark means that electrical and electronic equipment, batteries
and accumulators, at their end-of-life, should be disposed of separately from
your household waste.
Note:
If a chemical symbol is printed beneath the symbol mark, this chemical
symbol means that the battery or accumulator contains a heavy metal at a
certain concentration. This will be indicated as follows: Hg: mercury, Cd:
cadmium, Pb: lead
In the European Union there are separate collection systems for used
electrical and electronic equipment, batteries and accumulators.
Please, dispose of them correctly at your local community waste collection/
recycling centre.
Please, help us to conserve the environment we live in!
SANYO Sales & Marketing Europe GmbH
Stahlgruberring 4, D-81829 München, Germany
SANYO Electric Co., Ltd.
1-1, Sanyo-cho, Daito City, Osaka 574-8534, Japan
kFOR RUSSIAN USERS
This product is certified by an official certification company
which is authorized by the Russian Federation.
English
Download from Www.Somanuals.com. All Manuals Search And Downloiavd.
HOW TO READ THIS MANUAL
This instruction manual for your camera is organized into the following
sections.
k SETUP
Before taking pictures with your camera, you will need to familiarize
yourself with a few of its functions and complete some setup steps.
k BASIC OPERATION
An explanation of the fundamental operation for capturing images and
viewing images.
k APPENDICES
The camera specifications are found here.
kSymbols used in this manual
HINT
Points giving some extended instructions or special points to pay
attention to.
CAUTION Points that require special attention.
(page xx) Refer to the page indicated for detailed information.
You may find the answers to questions or problems concerning camera
operation in the ADVANCED INSTRUCTION MANUAL.
For information concerning how to use the accompanying CD-ROM (SANYO
Software Pack), please see the file “SANYO Software Pack INSTRUCTION
MANUAL.”
kHow to view the “INSTRUCTION MANUAL:
ADVANCED” and “SANYO Software Pack
INSTRUCTION MANUAL” files
1 Insert the CD-ROM (SANYO Software Pack) that was included with
your camera in your computer's CD-ROM drive.
2 Install the Adobe Reader 9 on your computer.
3 On the installation screen, click on “Instruction Manuals (PDF)”.
4 Click on the desired instruction manual.
v
English
Download from Www.Somanuals.com. All Manuals Search And Download.
SHOOT, PLAY BACK AND SAVE
Install the battery pack
1
Use the supplied charger to charge the battery pack.
h The CHARGE indicator is lit during charging.
h The CHARGE indicator will turn off when the battery pack is fully charged.
h Charging takes approximately 120 min.
Battery pack charger
Battery pack
[o] mark
CHARGE indicator
To power outlet
2
Open the battery/card compartment cover, and insert the battery pack.
h The battery/card compartment cover is located on the bottom of the
camera.
h Press the ON/OFF button to turn the camera on.
ON/OFF button
[o] mark
English
Download from Www.Somanuals.com. All Manuals Search And Downlovadi.
SHOOT, PLAY BACK AND SAVE
Before capturing those important shots, be sure to first take a
test shot to confirm that your camera is set up and ready to go
i
Sanyo declines any claim for compensation for recorded contents etc. in case
of photographing or recording failure due to a chance camera or card flaw.
Shooting
1
Press the [m] button.
h The recording mode menu
appears.
Shutter button
[l] / [m]
buttons
Single-shot
High-speed sequential shots
Sequential shots
Video clip recording
PHOTOGRAPH 1 IMAGE
2
3
Press the [l] or [m] button to
select the recording mode.
6
Press the SET button.
h The recording mode is
indicated by an icon in the
upper left area of the monitor.
4
Press the shutter button.
Single-shot mode:
A still image is captured.
High-speed sequential shots
mode/sequential shots mode:
Shooting begins. Release the
shutter button to discontinue
shooting.
Video clip recording mode:
Recording begins. To stop
recording, press the shutter
button again.
s: Single-shot mode
High-speed sequential shots mode
O: Sequential shots mode
:
X: Video clip recording mode
<Recording mode>
vii English
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback
kStill image playback
ON/OFF button
Playback button
[=]
1
Press the playback button [=].
h The display switches to the
Playback Screen.
h To view other images, press the
[l] or [m] button.
h If the playback button [=] is
pressed, the display returns to
the Shooting Screen.
kVideo clip playback
1
Press the playback button [=].
h The display switches to the
Playback Screen.
[l] / [m] buttons
h Press the [l] or [m] button to
display the video clip you wish to
play back.
2
Press the SET button.
h Playback of the selected video
clip begins.
SET
PLAY
h If the playback button [=] is
pressed again, the display
changes to the Shooting Screen.
<Example: After recording
a video clip>
When you are finished taking pictures...
Press the ON/OFF button to turn the camera off.
English viii
Download from Www.Somanuals.com. All Manuals Search And Download.
SHOOT, PLAY BACK AND SAVE
Copying files to a computer (Windows XP)
1
Install the software.
1 Insert the CD-ROM (SANYO Software Pack) that was included with
your camera in your computer’s CD-ROM drive.
h The installation screen appears.
2 Click on [ArcSoft MediaImpression 2] in the installation screen.
h Follow the messages on your computer screen to install the
software.
2
Use the supplied USB interface cable to connect your camera to the
computer.
h Connect the camera’s USB/AV terminal to the computer’s USB
connector.
h The USB Connection Screen appears on the camera’s monitor.
USB CONNECT ION
COMPUTER
PRINTER
CANCEL
CANCEL SET OK
Supplied dedicated USB
interface cable
To USB connector
on the computer
To the USB/AV terminal
ix English
Download from Www.Somanuals.com. All Manuals Search And Download.
3
4
Select “COMPUTER”, and press the SET button.
h The screen to select the connection mode appears.
Select “CARD READER”, and press the SET button.
h The camera is connected in the card reader mode.
h If the Windows automatic playback screen appears on the computer
monitor, close it.
5
Double-click on the desktop [MediaImpression 2] icon to launch
MediaImpression 2.
h The MediaImpression 2 home page appears.
[Import]
English
x
Download from Www.Somanuals.com. All Manuals Search And Download.
SHOOT, PLAY BACK AND SAVE
6
Click on [Import].
h The files in the camera are shown on the import screen.
Files in the camera
[Destination Folder] field and [Subfolder Name] field
[Import]
xi English
Download from Www.Somanuals.com. All Manuals Search And Download.
HINT
You can specify which folder to copy the files to.
i When you click on the folder icon in the [Destination Folder] field, the
screen to specify the copy destination appears.
i We suggest that you click on [{Today’s Date] in the [Subfolder Name] field
to select it. When [{Today’s Date] is selected, a subfolder named with the
current date is automatically created in the folder specified in the
[Destination Folder] field, and the files are copied to it.
Folder icon
7
8
9
Click on [Import].
h The files in the camera are copied to the computer.
When copying is completed, click on [Done].
h You are returned to the MediaImpression 2 home page.
Click on the close button to exit MediaImpression 2 and end the
program.
HINT
More about MediaImpression 2
i On the MediaImpression 2 home page, click on [Service & Support] for
more information.
English xii
Download from Www.Somanuals.com. All Manuals Search And Download.
SHOOT, PLAY BACK AND SAVE
Dismounting the camera
CAUTION
i To disconnect your camera, be sure to follow the procedure below. Failure
to follow this procedure may cause faulty operation of your computer or
loss of card data.
1
2
Left-click on the icon for safely removing hardware.
h A list appears showing the devices connected to the computer’s USB
connectors.
<Windows Vista>
h Close the window.
Left-click on the camera drive (E:).
h The camera can now be disconnected.
* The drive name (E:) may be different on your computer.
xiii English
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION
Insert and pull out the cable carefully
i When connecting the cables, make sure that the cable plugs are correctly
oriented and that they match the shapes of the terminal sockets on the
devices. Push the plugs in straight when connecting them. If undue force is
used to connect a cable, it may permanently damage the connector pins in
the terminal socket.
i Do not use excessive force when connecting and disconnecting cables.
i Please connect the dedicated USB interface cable to your computer’s USB
connector. Do not connect it to the USB port on your monitor or keyboard,
or to the USB hub. Be especially careful when installing the driver
software. In some instances, it may not be possible to correctly install the
driver software.
To access the data in the camera’s internal memory...
i Remove the card from the camera.
English xiv
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
CONTENTS ........................................................................................... 1
sold separately) ............................................................................. 5
Deleting files .................................................................................... 35
1
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Battery life ........................................................................................62
Possible Number of Images/Video Recording Time/
take a test shot to confirm that your camera is set up and
English
2
Download from Www.Somanuals.com. All Manuals Search And Download.
CHECKING THE INCLUDED ACCESSORIES
i Handstrap: 1
i SANYO Software Pack
(CD-ROM): 1
i Lithium-ion battery pack
(battery pack): 1
i Lithium-ion battery pack
charger and power cord
i Dedicated USB interface cable:
1
i Dedicated AV interface
cable: 1
i SAFETY MANUAL
i QUICK GUIDE
(safety precautions booklet)
Please read this booklet
carefully before using the
digital camera.
i INSTRUCTION MANUAL
BASICS
(VPC-X1220EX,
VPC-X1220GX,
VPC-X1220PX only)
3
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Attaching the handstrap
Media cards that can be used with this camera
The types of card that can be inserted into and used with this camera are:
i SD Memory Card
i SDHC Memory Card
What “card” means in this manual
i In this manual, SD Memory Cards and SDHC Memory Cards that can be
used in this digital camera are referred to as “card”.
English
4
Download from Www.Somanuals.com. All Manuals Search And Download.
CHECKING THE INCLUDED ACCESSORIES
Installing/removing the DC adaptor (Model VAR-A3: sold separately)
Install in the camera's battery slot, and connect the AC adaptor. Use in
conjunction with the AC adaptor.
Attaching the DC adaptor
1
Open the camera's battery/card
compartment cover.
2
Insert the DC adaptor into the battery slot.
h Make sure that the DC adaptor is correctly oriented when inserting,
and insert it firmly all the way.
3
4
Close the battery/card
compartment cover.
Connect the AC adaptor.
Removing the DC adaptor
1
2
3
Turn off the camera.
Remove the AC adaptor.
Open the camera's battery/card compartment cover, and remove the
DC adaptor.
5
English
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS NAMES
Rear
Strap holder
Zoom switch
Monitor
Playback button [=]
SCENE button
MENU button
[n] button
[m] button
SET button
[o] button
[l] button
7
English
Download from Www.Somanuals.com. All Manuals Search And Download.
CHARGING THE BATTERY PACK
Please charge the supplied battery pack before using it.
1
Connect the supplied power
cord to the socket on the
battery pack charger.
h Insert the connector straight
and securely.
Battery pack charger
Power cord
Battery pack charger
Battery pack
2
Insert the battery pack in the
battery charger.
h Insert it in the direction
indicated by the [o] mark
on the battery pack.
[o] mark
CHARGE
indicator
To power outlet
3
4
Plug the power plug into a
power outlet (AC 100 V to
240 V).
h Charging begins.
h The CHARGE indicator is lit
during charging.
When the CHARGE indicator
turns off, unplug the power
cord from the power outlet,
and remove the battery pack
from the charger.
HINT
i Charging takes approximately 120 min.
English
8
Download from Www.Somanuals.com. All Manuals Search And Download.
CHARGING THE BATTERY PACK
Charging the battery pack
Be sure to fully charge the supplied or separately sold battery pack before
using it in your camera. For charging the battery pack, use the supplied
charger.
Charge the battery pack if it is being used for the first time, and recharge it
whenever the remaining charge is low.
Does the battery pack feel hot?
i During charging, the charger and battery pack will be warm. This is normal
and does not indicate a malfunction.
If there is interference to your TV or radio during charging...
i Move the battery pack and charger further away from the TV or radio.
Ambient temperature during charging
i It is recommended that the ambient temperature during charging be
between about 10 °C and 35 °C (50 °F and 95 °F). Due to the
characteristics of the battery pack, at temperatures below 0 °C (32 °F), it
may not be possible to sufficiently charge it.
i When the battery pack temperature is high, the safety function may be
activated and halt charging.
Charge a battery pack in the following cases
i A battery pack which has not been used for a long time
i Newly purchased battery pack
FOR AMERICAN USERS:
i Use a UL Listed, 1.8 to 3 m (6 to 10 ft.), Type SPT-2 or NiSPT-2, AWG
No.18 power supply cord, rated for 125 V 7 A, with a non-polarized NEMA
1-15P plug rated for 125 V 15 A.
9
English
Download from Www.Somanuals.com. All Manuals Search And Download.
About the CHARGE indicator
The CHARGE indicator shows the status of the battery pack and the charger.
Please refer to the following table if the indicator flashes abnormally.
CHARGE indicator
Not lit
Not connected properly
i To recharge the battery pack, the power cord of the
charger must be connected to a power outlet, and the
plug at the other end inserted in the charger’s power
socket (page 8).
i The battery pack is not installed, or it is not installed
correctly (page 8).
Charging finished
Lit
Charging
Flashing
Problem with the battery pack or battery pack charger
i Immediately remove the battery pack from the charger.
i Do not use an abnormal battery pack. (The usable life of
the battery pack has probably expired.)
CAUTION
Do not charge the battery pack immediately after the camera has been
in continuous use for a long time
i The battery pack becomes hot when the camera is used continuously for a
long time. If you attempt to charge the battery pack in this state, the safety
function may be activated and it may not be possible to charge the battery
pack. Wait until the battery pack has cooled down before attempting to
charge it.
Does the battery pack appear swollen?
i The lithium-ion battery used in this camera may expand slightly when
stored in a hot environment or repeatedly used, but this is not a safety
hazard.
English 10
Download from Www.Somanuals.com. All Manuals Search And Download.
CHARGING THE BATTERY PACK
HINT
About the internal backup battery
i This camera’s internal battery serves to maintain the date and time
settings, as well as the shooting settings. The backup battery will be fully
charged when the battery pack is kept in the camera continuously for about
2 days. In the fully charged state, the backup battery will maintain the
camera settings for about 7 days.
When not using the camera for a long time, remove the battery pack
i A small amount of power is still used even if the digital camera is turned off,
and it is therefore recommended that the battery pack be removed from the
camera if it is not going to be used for a long time. Note that when the
battery pack is removed for a long period, the time and date settings may
be cleared. Before using your camera again, be sure to confirm that the
camera settings are correct.
To prolong the life of the battery pack
i Although the battery pack is an expendable item, you can maximize the life
of the battery by heeding the following suggestions.
h Do not leave the battery under the hot summer sun or exposed to other
high-temperature environments.
h Do not continually recharge the battery when it is already fully charged.
After fully charging it once, for example, use it for a while to partially
discharge it before charging it again.
h When the battery is not to be used for a long time, if possible store the
partially charged (not fully charged) battery in a cool environment.
11 English
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALL THE BATTERY PACK AND CARD
Installation
i Make sure that the battery pack and card orientation are correct.
i The card can be used after it has been formatted with the camera.
1
2
[o] mark
Open battery/card compartment cover
on the bottom of the camera.
Insert the battery pack.
3
4
Insert the card all the way until it
clicks.
Close the battery/card compartment
cover.
To remove...
<Battery pack>
<Card>
1 Open
1 Open
2 Push down
2 Push
3 Pull out
3 Pull out
English 12
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALL THE BATTERY PACK AND CARD
CAUTION
Do not remove the battery pack outer covering or label
i Do not use the battery with the outer covering or label removed, as doing
so may result in malfunction.
Be careful when removing the card
i Do not attempt to forcibly remove the card.
i Never remove the card when the camera is connected to a computer or
printer, or when the self-timer indicator is flashing quickly. In doing so, you
risk losing the data stored in the card.
Keep your finger on the card until it is completely inserted or released
i If you remove your finger too soon, the card may spring out and become
lost or hit someone in the eye.
HINT
Shooting without a card installed
i When a card is installed, images are recorded to and played back from the
card. When no card is installed, images are recorded to and played back
from the camera’s internal memory. When the camera is turned on with no
card installed, the internal memory icon
is shown on the monitor to let
you know that the images you capture will be saved to the camera’s
internal memory.
13 English
Download from Www.Somanuals.com. All Manuals Search And Download.
To format a card
1
Install the card in the camera. Turn
2
3
4
Select “FORMAT” and press the
SET button.
h The Format Screen appears.
Follow the instructions on the
screen to format the card.
MENU button
RECORDING MENU 1/2
RESOLUTION
2
M
COMPRESSION
PHOTO STABILIZER
FOCUS MODE
EXP MEASURE
ISO
SET OK
English 14
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALL THE BATTERY PACK AND CARD
Warning concerning battery pack temperature
i If the battery pack in the camera becomes too hot, a blinking temperature
warning icon \ will appear on the monitor. If the blinking icon does
appear, the camera should be turned off as soon as possible and the
battery pack allowed to cool before the camera is turned on again.
i Note that the camera will turn off automatically if it continues to be used
with the battery pack temperature elevated.
15 English
Download from Www.Somanuals.com. All Manuals Search And Download.
TURNING THE CAMERA ON AND OFF
Turning on the camera
In the recording mode
1
Press the ON/OFF button.
h The camera turns on.
ON/OFF button
h The camera turns on in the
recording mode that was active
before it was last turned off.
In the playback mode
1
Press the playback button [=] for
at least one second.
h The Playback Screen appears on
Playback button [=]
Monitor
Turning off the camera
1
Press the ON/OFF button.
h The camera turns off.
<If the camera was turned on by pressing the playback button [
=]>
h When the playback button [=] or ON/OFF button is pressed, the
camera turns off.
English 16
Download from Www.Somanuals.com. All Manuals Search And Download.
TURNING THE CAMERA ON AND OFF
About the auto power off function
In order to preserve battery pack power when, for example, the camera has
accidentally been left on, the camera is furnished with an “auto power off”
function by which the camera automatically turns off after a certain period of
inactivity (about 1 minute during shooting or about 3 minutes during playback
[factory default settings]).
i If the auto power save function has operated to turn the camera off, press
the ON/OFF button to turn it back on.
i You can change the setting for the time elapsed before the camera
automatically turns off.
i When the camera is connected to a computer or printer using the
dedicated USB interface cable, the auto power save function is disabled,
and the camera turns off after about 12 hours.
HINT
If the K icon appears...
i When a picture is taken, the date and time it was captured is recorded with
it. When the date and time cannot be recorded with the image because the
have the date and time recorded with images, please make this setting
before capturing images.
17 English
Download from Www.Somanuals.com. All Manuals Search And Download.
DATE AND TIME SETTING
The camera will record the date and time an image or audio recording is
taken so that you can display them during playback. Therefore, before
capturing images, make sure the correct date and time are set.
Example: To set the clock to 7:30 p.m. on December 24, 2010
1
Turn on the camera (page 16), and
press the SET button.
CLOCK SET
h The Clock Set Screen appears.
h Follow the procedures below to
enable or disable the date display
during playback, to set the display
format for the date, and to set the
date and time.
DATE
TIME
2010/01/01
00:00
DISP
Y/M/D
SET OK
h To display the Recording or
Playback Screen, press the
MENU button 2 times.
2
Set the date.
1 Select “DATE”.
CLOCK SET
2 Press the SET button.
h The Set Date Screen appears.
3 Set the date to “2010/12/24”.
h The date is set in the following
order: Set the year → Set the
month → Set the day.
DATE
2010/12/24
SET OK
h Press the [l] or [m] button to
select year, month or day.
Press the [n] or [o] button to
increase or decrease the
number.
4 Press the SET button.
English 18
Download from Www.Somanuals.com. All Manuals Search And Download.
DATE AND TIME SETTING
3
Set the clock.
1 Select “TIME”.
CLOCK SET
2 Press the SET button.
h The Set Time Screen appears.
3 Set the time to “19:30”.
h The time is set in the following
order: Set the hour → Set the
minute.
TIME
19:30
SETOK
h A 24-hour clock is used for the
time display.
4 Press the SET button.
4
Set the order in which the date is
displayed during playback.
1 Select “DISP”.
CLOCK SET
2 Press the SET button.
h The Set Date Format Screen
appears.
Y/M/D
DISP
3 Press the [n] or [o] button.
h Press the [n] button to change
the displayed date order as
follows:
SET OK
Y / M / D → M / D / Y → D / M / Y
Press the [o] button to change it in the reverse order.
4 Press the SET button.
19 English
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Press the MENU button.
h The date and time setting is completed.
h To display the Recording or Playback Screen, press the MENU button.
HINT
About the settings backup
i Under normal conditions, while the battery pack is being replaced, an
internal battery will maintain the date and time settings. However, there is a
small chance the settings may be lost (the backup will last for about
7 days). It is recommended to check that the date and time settings are still
correct after replacing the battery pack and before shooting or recording of
any type (follow step 1).
To correct the date and time settings
1 Turn on the camera, and press the MENU button.
2 Select the [E] tab, and press the SET button.
3 Select “CLOCK SET” and press the SET button.
h The screen to set the date and time appears.
h The current date and time settings are shown.
4 Select the line you wish to change, and make the correction.
English 20
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
BEFORE TAKING PICTURES
Switching between the recording mode and
playback mode
Switch between shooting and playing.
1
2
Press the ON/OFF button to turn
the camera on.
ON/OFF button
Playback button
[=]
Press the playback button [=].
h Each time the playback button is
pressed, the camera switches
between the recording mode and
the playback mode.
149
<Recording mode>
100-0001
2010.12.24
<Playback mode>
HINT
To turn the camera on in the playback mode
i Press the playback button [=] for at least 1 second, and the camera will
turn on in the playback mode.
21 English
Download from Www.Somanuals.com. All Manuals Search And Download.
How to switch the recording mode
Your camera can capture single still photos (single-shot mode), record video
clips (video clip recording mode), and also capture a series of still photos
(sequential shots mode).
1
2
Press the ON/OFF button to
turn the camera on.
ON/OFF button
[m] button
Press the [m] button.
h The screen to set the
recording mode and the self-
timer appears.
3
4
Press the [m] button to select
the recording mode.
Press the SET button.
h The selected recording mode
is set.
h An icon in the upper left area
of the monitor indicates the
active recording mode
setting.
SET button
149
<Recording mode>
s: Single-shot mode
:
High-speed sequential shots mode
O: Sequential shots mode
X: Video clip recording mode
English 22
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE TAKING PICTURES
Switching the display mode
In the recording mode, you can select the either the “settings display mode”
which allows you to confirm the shooting settings on the monitor while you
shoot, or the “normal display mode” in which the setting indications are turned
off, providing a full view of the subject.
1
2
Press the ON/OFF button to turn
the camera on.
ON/OFF button
SET button
Press the SET button.
h Each time the SET button is
pressed, the camera switches
between the settings display
mode and the normal display
mode.
149
<Settings display mode>
<Normal display mode>
Download from Www.Somanuals.com. All Manuals Search And Download.
23 English
Adjust the monitor brightness
The brightness of the monitor is adjustable. Adjust the brightness to the
optimum readability in the ambient light.
1
2
Press the ON/OFF button to
turn the camera on.
ON/OFF button
MENU button
Press the MENU button for at
least 1 second.
h The monitor brightness menu
appears.
3
4
Press the [l] and [m] buttons
to adjust the brightness.
Press the MENU button.
h The monitor brightness is
set, and the monitor
brightness menu is canceled.
[l] and [m] buttons
Monitor
HINT
i You can also adjust the monitor brightness by selecting “BRIGHTNESS”
from the Option Menu.
English 24
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE TAKING PICTURES
Hints for taking pictures
Muting the camera sounds
i The operation sounds that are generated, for example, when the shutter
button, MENU button or SET button is pressed, can be muted.
Where is the image data saved?
i All the image and sound data is recorded in the camera’s internal memory
or on the card installed in the camera.
i When a card is installed in the camera, the data is recorded on the card. If
no card is installed, the data is recorded in the camera’s internal memory.
Taking pictures in backlight conditions...
i When taking pictures with the light coming from behind the subject, due to
the characteristics of the CCD, light lines or ghost patterns (flare effect)
may appear in the captured image. In this situation, it is recommended that
you avoid taking pictures with the subject lit from behind.
Switching the guidance display ON/OFF
i Press the [l] button. Each time the [l] button is pressed, the guidance
display switches between ON and OFF.
149
149
[l]
Half-press shutter
button to focus
<Guidance display ON>
<Guidance display OFF>
HINT
i Images captured in the still image shooting mode can be rotated when
they are played back.
i When the optical zoom is used or when the autofocus is operating, the
image may appear to waver, but this is not a malfunction.
25 English
Download from Www.Somanuals.com. All Manuals Search And Download.
CAPTURING AND PLAYING BACK STILL IMAGES
There are two modes for capturing still images. In the single-shot mode, one
image is captured each time the shutter button is pressed. In the sequential
shots mode, when you press the shutter button, several successive images
are captured. For more information about taking sequential shots, please see
Shooting single shots
1
2
Set the camera to the single-
shot mode (page 22).
Shutter button
Rest your finger on the
shutter button.
h Engage the autofocus by
pressing the shutter button
halfway (focus lock).
3
Gently press the shutter
button.
h Press the shutter button
gently, taking care not to
move the camera.
h The image that was
captured appears on the
monitor as long as the
shutter button is kept
pressed (post view).
F5.2
1/102
Single-shot icon
<Single-Shot Screen>
English 26
Download from Www.Somanuals.com. All Manuals Search And Download.
CAPTURING AND PLAYING BACK STILL IMAGES
4
Release your finger from the shutter button.
h The captured image is recorded.
HINT
Focus indicator
Target mark
About the target mark
i A target mark & on the monitor shows
the area the camera is focusing on.
i The camera automatically determines
the correct focus by measuring from 9
different focus points within the
shooting area. If the target mark is at a
position that is different from the point
you wish to focus on, you can refocus,
for example, by changing the shooting
angle.
F5.2
1/102
i The large target mark appears when
the camera focuses on a wide area in
the center of the screen.
Shutter speed
Aperture
About the focus indicator
Motion alert icon
i A green focus indicator appears when
the subject is successfully focused, or
a red focus indicator when the camera
was not able to focus the subject.
The shutter speed and aperture are
displayed
12M
i The shutter speed and aperture
settings are also displayed on the
monitor. You can use them as a
reference when shooting.
F5.2
1/2
If the motion alert icon appears...
i During still image shooting, if the shutter speed is slow and the possibility
that the image may be blurred due to camera shake becomes high, the
motion alert icon may appear on the monitor. In this case, use a tripod to
stabilize the camera when shooting, or set the flash operation mode to
automatic (page 50).
i When shooting with the fireworks H scene function, the motion alert icon
always appears, but this is normal.
27 English
Download from Www.Somanuals.com. All Manuals Search And Download.
Shooting sequential shots
When the shutter button is pressed, still images are captured in succession.
1
2
Set the camera to the sequential
shots mode or the high-speed
sequential shots mode (page 22).
O: Sequential shots icon
: High-speed sequential
shots icon
143
4
Press the shutter button to start
shooting.
h Shooting sequential shots begins.
J Estimated maximum number of
sequential shots
<Sequential shots mode>
<High-speed sequential shots mode>
Resolution
Max. no. of shots
Approx. 3 shots
Approx. 4 shots
Approx. 7 shots
Approx. 11 shots
Approx. 22 shots
Approx. 121 shots
Resolution
Max. no. of shots
Approx. 25 shots
I
z
j
D
z
t
[
h The quantities indicate the number of shots when the compression
rate is set to j.
h The maximum number of sequential shots will differ depending on the
subject.
h Note that if the shutter button is released during shooting, shooting
stops immediately.
English 28
Download from Www.Somanuals.com. All Manuals Search And Download.
CAPTURING AND PLAYING BACK STILL IMAGES
HINT
About the focus when shooting sequential shots
i When sequential shots are captured, the autofocus operates when the
focus lock is activated, fixing the focus.
Can the self-timer and/or flash be used?
i The self-timer and flash do not operate when shooting sequential shots.
i The following scene functions cannot be set.
\]H_a5n
29 English
Download from Www.Somanuals.com. All Manuals Search And Download.
Viewing still images
The steps for viewing both single shots and sequential shots are the same.
1
Press the playback button
[=].
Playback button [=]
h If the playback button [=]
was pressed to turn the
camera on, however, press the
playback button [=] for at
least 1 second.
h The image most recently
captured appears on the
monitor.
2
View other images.
h Press the [l] or [m] button to
display the previous or next
image.
To display the previous image:
Press [l].
To display the next image:
100-0001
Press [m].
h To return to the Shooting
Screen, press the playback
button [=].
<If the camera was turned on by
pressing the playback button
[
=]>
2010.12.24
h When the playback button
[=] or ON/OFF button is
pressed, the camera turns off.
When you are finished viewing images...
i Press the ON/OFF button to turn the camera off.
HINT
i When the shutter button is pressed, the voice memo is played back.
English 30
Download from Www.Somanuals.com. All Manuals Search And Download.
CAPTURING AND PLAYING BACK STILL IMAGES
9-image/20-image display playback
1
2
Press the playback button
[=].
Zoom switch [W]/[T]
Press [W] ([P]) on the
zoom switch.
h The 9-image display
appears.
3
Select the image to play
back.
h Press the arrow buttons to
move the orange frame to
the desired image, and
press the SET button.
Instead of pressing the
SET button, you can press
[T] ([]]) on the zoom
switch to show the image
full screen.
SET button
Arrow buttons
h If [W] ([P]) on the zoom
switch is pressed while the
9-image display is shown,
the display changes to the
20-image display.
Orange frame
Still image
Video clip
100
0001
0002
0005
0003
0006
0004
0007
0008
0009
Audio recording
Folder number
Image number
31 English
Download from Www.Somanuals.com. All Manuals Search And Download.
Folder playback
A convenient way to search through multiple folders, or to search for an image
that was recorded using Screen Capture.
1
2
Access the 9-image display screen (page 31).
Press [W] ([P]) on the zoom
SELECT FOLDER
switch 2 times.
h The screen to select the playback
folder appears.
100SANYO
101SANYO
102SANYO
h If [T] ([]]) on the zoom switch is
pressed, the camera changes to
the 20-image display (page 31).
SET OK
3
Select the desired folder, and press
the SET button.
h The first image in the selected
folder is displayed.
h At this time, if you press [W] ([P])
on the zoom switch, the images in
the selected folder are shown in the
9-image display.
English 32
Download from Www.Somanuals.com. All Manuals Search And Download.
CAPTURING AND PLAYING BACK STILL IMAGES
Magnifying (zooming in) the image
1
2
Display the image that you want to magnify.
Press [T] ([]]) on the zoom
switch.
11212%
h Magnification is enabled.
h The image is magnified, and the
central portion of image is
displayed.
h Press the arrow buttons to view
different parts of the magnified
image.
Press shutter to save
MMoovvee
100%
To magnify:
Magnification increases with each
press of [T] ([]]) on the zoom
switch.
To go back:
Magnification decreases with each
press of [W] ([P]) on the zoom
switch.
h Press the SET button to return to
the normal (100%) view.
HINT
The magnified portion of the image can be saved as a separate image
i Press the shutter button. The magnified portion is saved as a new still
image.
33 English
Download from Www.Somanuals.com. All Manuals Search And Download.
Zoom jump playback
You can magnify a portion of a still image to check the accuracy of the focus.
1
2
Display a still image to view
using zoom jump playback.
Zoom switch [W]/[T]
Press the SET button.
h The image is magnified.
h If the magnified view appears
to be in focus, then the
overall image will be in focus.
3
Press the arrow buttons to
move to the part you wish to
magnify, and press [T] ([]])
on the zoom switch.
h The displayed area is further
magnified.
SET button
To magnify further:
Magnification increases with
each press of [T] ([]]) on the
zoom switch.
Arrow buttons
To go back:
Magnification decreases with
each press of [W] ([P]) on the
zoom switch.
h Press the SET button again
to return to the normal size
(100%) screen.
1250%
Press shutter to save
Move
100%
English 34
Download from Www.Somanuals.com. All Manuals Search And Download.
CAPTURING AND PLAYING BACK STILL IMAGES
Deleting files
You can delete files if you no longer need them. You can delete the files one
at a time, or all at once.
1
To delete files from the card, perform the delete procedure with the
card installed in the camera. To delete files from the camera’s
internal memory, remove the card before performing the delete
procedure.
2
Set the camera to the playback
mode, and press the [n] button.
DELETE
h The Delete Screen appears.
DELETE SINGLE:
Deletes one file at a time.
DELETE ALL:
DELETE SINGLE
DELETE ALL
Deletes all the files.
WT
OK
SET
3
Delete the files.
<To delete one file>
1 Use the [l] and [m] buttons to display the file you wish to delete.
2 Press the [n] or [o] button to select “DELETE SINGLE”.
h There is no confirmation screen when deleting single files. Before
pressing the SET button in step 3, please make sure that the
displayed image is one you wish to delete.
3 Press the SET button.
h The currently displayed file is deleted.
h To delete other files, repeat steps 1 to 3.
35 English
Download from Www.Somanuals.com. All Manuals Search And Download.
<To delete all the files>
1 Use the [l] and [m] buttons to view the images and check if it is OK
to delete all the files.
2 Press the [n] or [o] button to select “DELETE ALL”.
3 Press the SET button.
h The Delete Confirmation Screen appears. To delete the files,
select “YES”, and press the SET button. When the file delete is
completed, “No image” is shown.
CAUTION
About protected images
i Files that are protected from accidental delete cannot be deleted. To delete
protected files, set the protect setting for the file to off, and then follow the
file delete procedure.
English 36
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO CLIP RECORDING AND PLAYBACK
Recording a video clip
1
Set the camera to the video
clip recording mode
Shutter button
2
Press the shutter button.
h Video clip recording
begins. During recording,
the length of the video clip
and the remaining
recording time available
are shown on the monitor.
h It is not necessary to
continue pressing the
shutter button while
recording.
Recorded length (time) of
video clip
3
End the recording.
h Press the shutter button
again to stop recording and
save the video clip.
Remaining recording time
available
TV
0000::4455::0000
00:00:30
Video clip recording icon
37 English
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing back the video clip
4
Press the playback button
[=].
Playback button [=]
h If the playback button [=]
was pressed to turn the
camera on, however, press
the playback button [=] for
at least 1 second.
h The video clip just recorded
appears on the monitor.
5
Press the SET button.
h Video clip playback begins.
h To stop playback, press the
[o] button.
[o] button
SET button
SET
PLAY
English 38
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO CLIP RECORDING AND PLAYBACK
Outline of playback operation
To do this...
Do this
Stop playback
During playback, press the [o] button.
During playback, press the SET button.
During accelerated or slow playback, press
the [n] button.
Pause
To extract a still image
While playback is paused, press the shutter button.
To playback
one image
at a time
(single-
While playback is paused, press the [m]
button.
Forward
Reverse
While playback is paused, press the [l]
button.
frame step)
While playback is paused, press and hold the
[m] button.
Forward
Reverse
Slow
playback
While playback is paused, press and hold the
[l] button.
During forward playback, press the [m] button.
iThe playback speed changes each time the
[m] button is pressed, as follows:
Normal playback → 2× → 5× → 10× → 15×
Press the [l] button to resume normal
playback speed.
Forward
Reverse
To
accelerate
playback
During forward playback, press the [l] button.
iThe playback speed changes each time the
[l] button is pressed, as follows:
15× ← 10× ← 5×
Press the [m] button to resume normal
playback speed.
Return to normal playback
speed
Press the SET button.
Louder: During playback, press [T] on the
zoom switch.
Softer: During playback, press [W] on the
Adjusting the volume
zoom switch.
39 English
Download from Www.Somanuals.com. All Manuals Search And Download.
When you are finished viewing video clips...
i Press the ON/OFF button to turn the camera off.
CAUTION
How to save one frame from a video clip as a still image
1 Play back the video clip. Pause the playback at the point you wish to
“snap” a photo.
2 Press the shutter button.
i The currently displayed frame is saved as a still image.
The data for a video clip is very large
i Therefore, be aware that if the video clip is uploaded to a computer to be
played back, the computer may not be able to play back the video fast
enough, making it appear jerky. (The video will always be displayed
properly on the camera monitor.)
If video clip recording stops even when there is card memory
remaining…
i Depending on the card you are using, recording may stop even if there is
remaining memory in the card.
i For video clip recording, it is recommended that a high-speed memory
card be used.
If no audio is heard...
i The audio is not played back when the video clip is played back in the
frame-by-frame, slow playback, fast playback or reverse playback mode.
During video clip playback, the sound of a motor is audible...
i During recording, the sound of the optical zoom movement or autofocus
movement was recorded. This is not a malfunction.
Does video clip playback stop when you adjust the volume?
i If you adjust the volume during video clip playback, the playback may
temporarily pause. This is not a malfunction.
English 40
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE SCENE FUNCTION
You can select from a variety of preset settings (aperture, shutter speed, etc.)
for specific shooting conditions.
1
Set the camera to the recording
mode (page 21), and press the
SCENE button.
AUTO
h The screen to select a scene
function appears.
Use auto settings
2
Use the arrow buttons to select the
desired setting.
<Example: In the single-
shot mode>
<Features of each scene function>
Recording mode setting
Scene function
Features
s
O
X
m
m
X
Auto
The camera makes the
optimum settings.
m
m
m
m
m
m
Y
Sports
Capture a split-second image
of a fast-moving subject.
Enhance the three-
dimensional feel of the
subject by blurring the
background. (With face
chaser function)
G
Portrait
*
*
*
*
m
m
m
m
\
Landscape
For beautiful shots of distant
scenery.
m
m
n
n
n
n
m
m
]
Night view
portrait
Photograph the subject while
keeping the background
night scenery.
n
Capture a photo at the
m
m
n
n
n
n
n
m
Smile detection instant the subject smiles.
H
Fireworks
For capturing fireworks at
night.
41 English
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording mode setting
Scene function
Features
s
O
X
m
_
Lamp
Photograph in low-light
conditions.
m
n
n
n
a
Still image with
audio
Shoot a still image and add a
voice memo.
m
m
n
n
n
n
Four successive still images
are captured as the exposure
changes.
5
Best shot
n
The subject’s face is kept in
focus and the exposure
adjusted as the image is
captured.
r
Face chaser
*
*
*
m
m
m
m
8
Monochrome
Create black-and-white
photos.
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
9
Sepia
Create sepia-tone photos.
>
Contrast
Accentuates the light and
dark areas in the image.
@
Vivid
Accentuates the colors in the
image.
m: Available n: Not available
*
: Disabled during recording
3
Press the SET button.
h This completes the scene select
setting.
6
h The display returns to the Shooting
Screen.
h The scene function setting is shown
on the monitor.
Scene function setting
(X is not displayed)
English 42
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE SCENE FUNCTION
Capture a still image with a voice memo
With the still-image-plus-audio a scene function, you can add an audio
track (about 10 seconds maximum) to a captured still image. This audio track
is called a “voice memo”.
1
2
press the SET button.
Press the shutter button to take the
picture, then speak into the
microphone.
Recorded length of
audio track
Remaining recording time
available
h During recording, be careful not to
obstruct the microphone with your
fingers, for example.
h Audio recording begins. During
recording, the length of the audio
track and the remaining recording
time available are shown on the
monitor.
00:00:02
00:00:08
h The maximum recording time for a
voice memo is about 10 seconds.
h To end the recording before
10 seconds has elapsed, press the
shutter button.
43 English
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use the best shot feature
1
2
Set the camera to the single-shot mode; on the screen to select a
Press the shutter button.
h While the settings change, four still
images are shot in sequence.
h After the images are captured, the
four still images are displayed on
the monitor.
<To save all four images>
h With all four images showing on the
monitor, press the MENU button.
SELECT
OK
ALL
3
4
Use the arrow buttons to move the orange frame to the image you
wish to save.
h For a full-size view of the selected image, press the SET button.
h With the full-size view active, you can use the [l] and [m] buttons to
view the previous or next image.
h To return to the screen in step 2, press the MENU button.
With the full-size view of the image
you wish to save, select “YES”, and
press the SET button.
Delete other images?
h The image currently displayed is
saved, and the other images are
deleted.
YES
EXIT
SET
OK
English 44
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE SCENE FUNCTION
How to use the face chaser feature
To attain the best possible face shots, the camera automatically focuses on
the face and adjusts the exposure.
1
2
press the SET button.
Aim the camera lens at the subject.
h The camera searches for the
Green frame
subject’s face. When it detects the
1432
face, a green frame appears.
h Do not touch the shutter button while
the camera is searching. The
camera cannot search when the
autofocus is activated.
3
4
h The camera focuses on the subject and the exposure is adjusted.
h When the face is in focus, the green frame changes to orange.
Press the shutter button.
h The image is captured.
CAUTION
i The digital zoom is disabled.
i The face chaser function does not work when zooming in or out.
i The face chaser function may not work when the subject’s face in the
monitor is relatively small or appears dark.
For images captured using the face chaser feature
i On the Playback Screen, when zooming in, the face that was defined by
the double frame during capture becomes the zoom center.
45 English
Download from Www.Somanuals.com. All Manuals Search And Download.
How to shoot using Smile Detection
Capture a photo at the instant the subject smiles.
Normal shooting
1
2
press the SET button.
Aim the camera lens at the subject.
h The camera searches for the subject's face. When it detects the face,
a green frame appears. The image is automatically captured when the
subject smiles.
Selecting the shooting area of the desired subject
From the multiple faces, select the area that frames the targeted face, and
capture the image when the selected subject smiles.
1
press the SET button.
2
3
Aim the camera lens at the subject.
Press the SET button.
h An orange frame appears, and the screen for you to select the area
that encompasses the target subject's face appears.
English 46
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE SCENE FUNCTION
4
5
Use the arrow buttons to move the orange frame to the area that
encompasses the target subject's face.
Press the SET button.
h The orange frame changes to yellow, and the Smile Detection area is
fixed.
h The camera adjusts the focus and exposure for the framed face.
h When the face is in focus, the green frame changes to a double frame.
h The image is automatically captured when the subject in the selected
area smiles.
HINT
The camera can't detect the smiling face?
i The camera cannot detect the subject's smile when zooming in or out.
i Smile Detection may not work accurately when the face in the monitor
appears small or dim.
For best results with Smile Detection
i Smile Detection works best when the subject is directly facing the camera
and showing his/her teeth when smiling.
Can't use the self-timer?
i The self-timer cannot be used with Smile Detection.
To cancel Smile Detection...
i Select a different scene function.
47 English
Download from Www.Somanuals.com. All Manuals Search And Download.
OTHER RECORDING FUNCTIONS
Using the zoom
Your camera has two zoom functions: optical zoom and digital zoom.
1
2
Set the camera to the recording
camera lens at the subject.
Zoom switch [W]/[T]
Press the zoom switch to
compose the desired image.
[T]: Zoom in on the subject.
[W]: Zoom out.
h When the zoom switch is
pressed, the zoom bar appears
on the monitor.
h When the optical zoom factor is
at maximum, zooming stops
temporarily. When [T] on the
zoom switch is pressed again,
the mode changes to the digital
zoom mode and zooming
continues.
Monitor
Zoom bar
Pointer
When both optical
and digital zoom
are enabled
3
Take the picture.
Optical zoom
Digital zoom (yellow)
When optical zoom
only is enabled
English 48
Download from Www.Somanuals.com. All Manuals Search And Download.
OTHER RECORDING FUNCTIONS
HINT
Can’t access the digital zoom?
i The digital zoom cannot be used when the face chaser r, smile
detection n or portrait mode
mode is set to AF seeker p.
Can’t access the optical zoom?
scene function is active, or the focus
G
i When the focus range is set to pan o or during video clip recording, the
optical zoom cannot be used.
49 English
Download from Www.Somanuals.com. All Manuals Search And Download.
Flash setting
The flash is used not only for taking pictures where there is insufficient light,
but also when the subject is in shade or in backlight conditions. Your camera’s
flash has four modes of operation (auto mode, forced flash mode, flash off
mode and red-eye reduction mode). Select the flash mode that is appropriate
for the surrounding conditions. The flash can be enabled only when taking
single-shot still images.
1
Set the camera to the single-shot
(?) button.
[n] (?) button
h The flash menu appears.
k: The camera will detect the
subject brightness and use the
flash only when required. In a
backlight situation, if only the
center of the image is very dark,
the flash will operate to
compensate (auto).
m: The flash will operate with every
image captured regardless of the
conditions. Use this setting
under backlight conditions, when
the subject is in shade, under
fluorescent lighting conditions,
etc. (forced flash).
FLASH
l: The flash will not operate even in
dark situations. Use this setting
when capturing an image in a
location where flash
AUTO
photography is prohibited, or
when shooting a night landscape
scene (flash off).
Flash menu
J: The digital camera will detect the subject brightness and use the
flash only when required. At this time the flash will operate in a
manner that reduces the red reflection (“red-eye”) in the subject’s
eyes (red-eye reduction).
English 50
Download from Www.Somanuals.com. All Manuals Search And Download.
OTHER RECORDING FUNCTIONS
2
3
Press the [n] or [o] button to select the desired flash mode, and
press the SET button.
Press the shutter button.
h The picture is snapped and the flash operates according to the
selected mode.
HINT
When auto is selected...
i The k icon indicating the flash setting is not shown on the Shooting
Screen.
When auto or red-eye reduction is selected...
i When the shutter button is pressed, if the camera determines that the flash
is necessary, a k or J icon appearing on the monitor indicates that
the flash will operate.
51 English
Download from Www.Somanuals.com. All Manuals Search And Download.
Self-timer
Self-timer photography is available in the single-shot mode.
1
Set the camera to the single-shot
[m] (
) button
[m] (
) button.
h The self-timer menu appears.
y: The image is captured about
2 seconds after the shutter
button is pressed.
x: The image is captured about
10 seconds after the shutter
button is pressed.
2
Use the [n] and [o] buttons to
select the desired self-timer
setting, and press the SET
button.
h The self-timer is set, and you are
returned to the Shooting Screen.
PHOTOGRAPH 1 IMAGE
Self-timer menu
English 52
Download from Www.Somanuals.com. All Manuals Search And Download.
OTHER RECORDING FUNCTIONS
HINT
i The countdown time until shutter
release is shown graphically on the
monitor.
F5.2
1/102
To pause or cancel the self-timer function...
i If the shutter button is pressed again before the shutter is released, the
self-timer countdown temporarily stops. Press the shutter button one more
time to restart the self-timer.
i To cancel self-timer photography, set the self-timer setting to off s.
i After the self-timer picture is snapped, the self-timer is automatically reset
to off.
When x is selected...
i When the shutter button is pressed,
the self-timer indicator flashes for
approximately 10 seconds, after
which shooting begins.
Self-timer indicator
i About 3 seconds before shooting,
the self-timer indicator flashes
faster.
53 English
Download from Www.Somanuals.com. All Manuals Search And Download.
Focus range
1
Set the camera to the recording
(R) button.
[o] (R) button
h The focus range menu appears.
o: The focus operates within the
ranges shown below (pan).
<Still image shooting>
i At maximum aperture setting:
2.5 m (8.20 ft.) to ∞
i At minimum aperture setting:
2 m (6.56 ft.) to ∞
<Video clip recording>
i Wide end:
At maximum aperture setting:
80 cm (31.50 in.) to ∞
At minimum aperture setting:
52 cm (20.47 in.) to ∞
i Tele end:
At maximum aperture setting:
3.3 m (10.83 ft.) to ∞
At minimum aperture setting:
2.2 m (7.22 ft.) to ∞
FOCUS
AUTO
*: The camera automatically
focuses on the subject within a
range of 10 cm (3.94 in.) (Wide
end) or 60 cm (23.62 in.) (Tele
end) to infinity (auto).
Focus range menu
+: You can focus on a subject within
the following ranges (macro):
Wide end: 5 cm (1.97 in.) to
80 cm (31.50 in.)
Tele end: 60 cm (23.62 in.) to
80 cm (31.50 in.)
-: The focus can be manually set to
any distance from 5 cm (1.97 in.)
to 8 m (26.25 ft.), as well as to
infinity (manual).
English 54
Download from Www.Somanuals.com. All Manuals Search And Download.
OTHER RECORDING FUNCTIONS
2
Press the [n] or [o] button to select the desired focus range, and
press the SET button.
h The specified focus range is set, and the camera returns to the
Shooting Screen.
HINT
i In the single-shot mode and sequential shots mode, when the focus range
is set to macro +, the zoom is automatically set to one step from the
wide end. When the focus range is set to pan o, the zoom is
automatically set to the Wide end.
55 English
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use the manual focus
1
Select manual - from the focus
range menu, and press the SET
button.
h The focus distance adjustment bar
appears.
FOCUS
MANUAL
70cm
2
Press the [l] or [m] button to adjust
the focus distance, and press the
SET button.
h The focus distance is set, and you
are returned to the Shooting
Screen.
HINT
About the focus range
i The focus distance indication shows the distance between the lens surface
and the subject.
i In some cases there may be a slight variance between the distance
(numerical figure) you set in the manual focus mode and the actual
distance. Use the monitor to confirm the focus and compose the photo.
About zoom movement when using the manual focus
i If the focus distance is set to 50 cm (19.69 in.) or less, the zoom changes
to the largest setting that is suitable for that focus distance.
i When the focus distance is set to 50 cm (19.69 in.) or less, the zoom will
function only within the range at which the image is focused.
English 56
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCESSING THE MENUS
Detailed camera settings are accessed from the menus.
1
2
Turn on the camera, and set it to the
recording or playback mode.
h Set the camera to the recording
mode to display the Recording
Menu, or the playback mode to
display the Playback Menu.
Press the MENU button.
h The menu for the mode specified in
step 1 appears.
MENU button
RECORDING MENU 1/2
RESOLUTION
2
M
COMPRESSION
PHOTO STABILIZER
FOCUS MODE
EXP MEASURE
ISO
SET OK
Exit the menu
Press the MENU button to exit the menu.
57 English
Download from Www.Somanuals.com. All Manuals Search And Download.
How to operate the menus
Use the arrow buttons to select the item you wish to change, press the SET
button, and the corresponding screen will appear.
1
2
Select the s or = tab.
Display the Recording Menu:
Select the s tab.
Display the Playback Menu:
Select the = tab.
Display the Option Menu:
Select the 3 tab.
Tab
RECORDING MENU 1/2
RESOLUTION
2
M
COMPRESSION
PHOTO STABILIZER
FOCUS MODE
EXP MEASURE
ISO
SET OK
<Example: Recording mode>
3
4
Press the [m] button.
RECORDING MENU 1/2
RESOLUTION
2
M
COMPRESSION
PHOTO STABILIZER
FOCUS MODE
EXP MEASURE
ISO
Press the [n] or [o] button to select
an item to set.
SET OK
5
Press the SET button.
RESOLUTION
h The Setting Screen appears.
h Press the [n] or [o] button to select
the desired setting, and then press
the SET button to complete the
setting.
4000 x 3000
9 M 4000 x 2256[16:9]
12
6M
2816 x 2112
4M
2288 x 1712
2M
M
0.3M
1600 x 1200
640 x 480
h To cancel the menu, press the
MENU button.
SET
OK
<Example: When
“RESOLUTION” is selected>
English 58
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDICES
SPECIFICATIONS
Camera
Image file format
Still images: JPEG format (DCF, DPOF, Exif
2.2 compliant)
Note: Designed mainly by the Japan
Electronics and Information Technology
Industries Association (JEITA), DCF
(Design rule for Camera File system) is
standard for digital still camera image
files to provide interoperability between
digital photography devices for the
images stored on removable memory
cards. However, it is not guaranteed that
all devices will support the DCF standard.
Video clips:QuickTime Movie (Photo-JPEG)
Audio recordings:WAVE format (monaural)
Data storage media
Internal memory: Approx. 50 MB
External memory: SD Memory Card
(equivalent to a 32 GB SDHC Memory Card)
Camera effective number Approx. 12.1 million pixels
of pixels
Image sensor
1/2.3-inch (1.1 cm) CCD
Virtual number of pixels: Approx. 12.5 million
pixels, interlace scan, primary color filter
Recording resolution
<Still image shooting>
I: 4000 × 3000 pixels
j: 4000 × 2256 pixels (16:9 aspect ratio)
D: 2816 × 2112 pixels
z: 2288 × 1712 pixels
t: 1600 × 1200 pixels
[: 640 × 480 pixels
<Video clip recording>
d: 640 × 480 pixels, 30 frames/second
5: 320 × 240 pixels, 15 frames/second
White balance
Full-auto TTL; manual setting available
59 English
Download from Www.Somanuals.com. All Manuals Search And Download.
Lens
3.0× optical
zoom lens
f=6.3 mm to 18.9 mm
(35 mm film camera
conversion: 35 mm to
105 mm)
Autofocus, 5 groups,
6 elements (4 with aspheric
surfaces)
Aperture
Open F=3.1 (Wide) to 5.9 (Tele)
Exposure control type
Programmable AE
Exposure correction available from the
Recording Menu (0 1.8EV in 0.3EV steps)
Light-measuring modes
Range
Multi-section measuring, center-weighted
measuring, spot measuring
Normal photography: 10 cm (3.94 in.) to ∞
(Wide), 60 cm (23.62 in.) to ∞ (Tele)
Macro photography: 5 cm (1.97 in.) to 80 cm
(31.50 in.) (Wide), 60 cm (23.62 in.) to 80 cm
(31.50 in.) (Tele)
Digital zoom
For shooting: 1× to 4×
For playback: 1× to 62.5× (varies with resolution)
Shutter speed
Single-shot mode: 1/2 to 1/1,500 sec.
(Maximum approx. 2 seconds when the
scene function is set to fireworks Hetc.)
(During flash: 1/30 to 1/1,500 sec.)
Sequential shots mode:
1/2 to 1/1,500 sec.
Video clip recording mode:
1/30 to 1/2,500 sec.
Sensitivity (standard
output sensitivity)
Single-shot mode/sequential shots mode
(standard output sensitivity):
Auto (ISO 64 to 400)/ISO 64, ISO 100,
ISO 200, ISO 400, ISO 800, ISO 1600,
ISO 3200, and ISO 6400 (switchable from
Recording Menu)
Video clip recording mode:
Auto (ISO 384 to 2400)
* Sensitivity measured in compliance with
the ISO standard (ISO 12232:2006).
English 60
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Monitor
2.7-inch (6.9 cm) TFT color LCD
Approx. 230,000 pixels
(Frame coverage: Approx. 100%)
Brightness adjustment: 5-step
Flash working range
GN = 5.2
Approx. 60 cm (23.62 in.) to 3.3 m (10.83 ft.)
(Wide)
Approx. 60 cm (23.62 in.) to 1.7 m (5.58 ft.)
(Tele)
Flash modes
Focus
Auto-flash, forced flash, flash off, red-eye
reduction
TTL-type AF (9-point range finder/spot focus/
AF seeker), manual focus (14 steps)
Self-timer
Approx. 2-second delay, 10-second delay
Ambient
environment
Temperature 0 to 40 °C (32 to 104 °F) (operation),
–20 to 60 °C (–4 to 140 °F) (storage)
Humidity
30 to 90% (operating, no condensation)
10 to 90% (storage, no condensation)
Power supply
Lithium-ion battery pack (DB-L80) × 1
Dimensions (at narrowest 92.8 (W) × 55.2 (H) × 17.0 (D) mm
part, not including grip or 3.65" (W) × 2.17" (H) × 0.67" (D)
lens protrusion)
Weight
Approx. 97 g (3.42 oz.) (camera only [without
battery pack and card])
Approx. 114 g (4.02 oz.) (including battery pack
and card)
61 English
Download from Www.Somanuals.com. All Manuals Search And Download.
Camera connectors
USB/AV
Dedicated regrouped jack
(communication/audio
and video output)
terminal
Audio
output
180 mVrms (–12 dBs), 2.2 kΩ or less,
monaural
Video
output
1.0 Vp-p, 75 Ω unbalanced, sync
negative, composite video, NTSC
color TV system/PAL TV system
(switchable from the Option Menu)
USB
USB 2.0 Full Speed
PC camera: USB video class
Battery life
Maximum recording time
170 images:
CIPA standard (when a Toshiba 128 MB
SD Memory Card is used)
Maximum playback time
310 minutes:
LCD monitor on, continuous playback
i Until battery pack runs out when using a fully charged battery pack at a
25 °C (77 °F) ambient temperature.
i The operation time may vary depending on the conditions of the battery
pack and the conditions of use. Especially when used at temperatures
below 10 °C (50 °F), the battery pack operation time is drastically reduced.
English 62
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Possible Number of Images/Video Recording
Time/Audio Recording Time
Recording
mode
setting
SD Memory Card
2 GB 8 GB
Resolution Compression
Internal
memory
setting
rate setting
j
0
j
0
j
0
12 images
19 images
17 images
25 images
26 images
38 images
502 images
754 images
665 images
997 images
1,010 images
1,500 images
1,960 images
2,950 images
2,600 images
3,900 images
3,970 images
5,900 images
I
j
D
Single-shot
mode/
Sequential
shots mode
z
j
39 images
58 images
1,500 images
2,200 images
5,900 images
8,650 images
0
O
j
0
j
0
79 images
3,090 images 12,100 images
4,410 images 17,300 images
t
118 images
399 images 15,400 images 60,500 images
532 images 20,600 images 80,700 images
[
Video clip
recording
mode
d
—
—
28 sec. 18 min. 10 sec.
1 hr. 11 min.
6 hr. 19 min.
5
2 min. 30 sec.
26 min. 30 sec.
1 hr. 36 min.
Audio file
mode
—
—
17 hr. 10 min.
67 hr. 10 min.
i Up to 9 hours of continuous audio recording is possible.
i When recording a video clip using an 8 GB card, recording terminates
when the size of the file currently being recorded reaches approx. 4 GB.
i The values were determined using an SD Memory Card by Sandisk.
i Even with cards of the same capacity, the amount of data that can actually
be stored may differ depending on the card brand, etc.
i The continuous shooting time for each video clip will differ depending, for
example, on the card capacity, environmental conditions (temperature and
shooting conditions, etc.).
63 English
Download from Www.Somanuals.com. All Manuals Search And Download.
Supplied battery pack charger
Part No.
VAR-L80
Power source
Rated output
Compatible batteries
AC 100 to 240 V, 50 to 60 Hz, 5 W
DC 4.2 V, 550 mA
Supplied or separately sold Lithium-ion
battery pack (DB-L80)
0 to 40 °C (32 to 104 °F) (recharge),
–20 to 60 °C (–4 to 140 °F) (storage)
Temperature
Humidity
Ambient
environment
20 to 80% (no condensation)
84 (W) × 22.5(H) × 50.5 (D) mm
3.31" (W) × 0.89" (H) × 2.00" (D)
Dimensions
Weight (without power cord) Approx. 49 g (1.73 oz.)
VPC-X1250
AC 125 V, 7 A
Power cord
rated value
VPC-X1220EX AC 250 V, 2.5 A
i The VPC-X1220GX and VPC-X1220PX models are supplied with a power
cord that is appropriate for the region of destination.
i When using the supplied battery pack charger abroad, the power cord may
need to be replaced in accordance with local requirements. Please contact
your local dealer for details.
Supplied Li-ion battery pack
Model number
Voltage
DB-L80
3.7 V
Capacity
700 mAh
Ambient
environment
Temperature 0 to 40 °C (32 to 104 °F) (during use)
–10 to 30 °C (14 to 86 °F) (storage)
Humidity
10 to 90% (no condensation)
Dimensions
Weight
39.2 (W) × 5.9 (H) × 31.4 (D) mm
1.54 (W) × 0.23 (H) × 1.24 (D) in.
Approx. 15 g (0.5 oz.)
English 64
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Others
Mac OS and QuickTime are trademarks of Apple Inc., registered in the U.S.
and other countries.
Microsoft and Windows are registered trademarks of Microsoft Corporation in
the USA and other countries.
Intel and Pentium are registered trademarks of Intel Corporation (USA).
®
®
®
In this manual, the Microsoft Windows 2000 operating system, Microsoft
®
®
®
Windows XP operating system, Microsoft Windows Vista operating
®
®
system, and Microsoft Windows 7 operating system are collectively
referred to as “Windows”.
SDHC logo is a trademark.
All other company and product names are registered trademarks or
trademarks of their respective owners.
CAUTION
i It is forbidden to copy this manual, whole or in part, without prior written
permission.
i All images and illustrations given in this manual are for explanation
purposes and may differ slightly from that of the actual product. Also,
actual specifications are subject to change without prior notice and
therefore may differ from the contents of this manual.
65 English
Download from Www.Somanuals.com. All Manuals Search And Download.
Before capturing those important shots, be sure to first take a
test shot to confirm that your camera is set up and ready to go
i Sanyo Electric shall not be held responsible for any problems resulting
from the use of this camera.
i Sanyo Electric declines all responsibility for damages due to improper use
of the camera, failure to adhere to the instructions given in this manual, or
repairs or changes done by those other than a technician authorized by the
manufacturer.
i Sanyo Electric shall not be held responsible for any damage caused by
optional devices or consumable items used with the camera other than
those supplied with the camera or those specified by Sanyo Electric.
i Sanyo Electric shall not be held responsible for any losses or loss of
revenue resulting from the loss of data caused by the malfunction, or the
repairing of a malfunction, of the camera.
i The images captured with this camera will differ in quality from pictures
taken with a standard film camera.
English 66
Download from Www.Somanuals.com. All Manuals Search And Download.
SANYO Electric Co., Ltd.
Download from Www.Somanuals.com. All Manuals Search And Download.
|