Multimedia Projector
MODEL
PLC-XF60
PLC-EF60
✽ Projection lens is optional.
Owner's Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
(Digital and Analog RGB) . . . . . . . . . . . . . . . . . . . . . .22
(Warp & Blending) . . . . . . . . . . . . . . . . . . . . . . . . . . .23
(Digital and Video) . . . . . . . . . . . . . . . . . . . . . . . . . . .24
(Component and RGB Scart) . . . . . . . . . . . . . . . . . . .25
3
Download from Www.Somanuals.com. All Manuals Search And Download.
To The Owner
Before operating this projector, read this manual thoroughly
and operate the projector properly.
Safety Precaution
This projector provides many convenient features and
functions. Operating the projector properly enables you to
manage those features and maintains it in better condition for
a considerable time.
Improper operation may result in not only shortening the
product-life, but also malfunctions, fire hazard, or other
accidents.
If your projector seems to operate improperly, read this
manual again, check operations and cable connections and try
the solutions in the “Troubleshooting” section in the end of
this booklet. If the problem still persists, contact the dealer
where you purchased the projector or the service center.
WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
– This projector produces intense light from the projection
lens. Do not stare directly into the lens as possible. Eye
damage could result. Be especially careful that children do
not stare directly into the beam.
– Install the projector in a proper position. If not, it may
result in a fire hazard.
– Provide appropriate space on the top, sides and rear of the
projector cabinet for allowing air circulation and cooling the
projector. Minimum clearance must be maintained. If the
projector is to be built into a compartment or similarly
enclosed, the minimum distances must be maintained. Do
not cover the ventilation slot on the projector. Heat build-
up can reduce the service life of your projector, and can
also be dangerous.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
SIDE and TOP
REAR
CAUTION : TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE EXCEPT LAMP REPLACEMENT.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
3.3'(1m)
3.3'(1m)
3.3'(1m)
3.3'(1m)
– Do not put any flammable object or spray can near the
projector, hot air is exhausted from the ventilation holes.
THIS SYMBOL INDICATES THAT DANGEROUS
VOLTAGE CONSTITUTING A RISK OF ELECTRIC
SHOCK IS PRESENT WITHIN THIS UNIT.
– If the projector is not to be used for an extended time,
unplug the projector from the power outlet.
THIS SYMBOL INDICATES THAT THERE ARE
IMPORTANT OPERATING AND MAINTENANCE
INSTRUCTIONS IN THE OWNER'S MANUAL WITH
THIS UNIT.
READ AND KEEP THIS OWNER'S MANUAL FOR LATER
USE.
CAUTION
Not for use in a computer room as defined in the Standard for
the Protection of Electronic Computer/Data Processing
Equipment, ANSI/NFPA 75.
Ne peut être utilisé dans une salle d’ordinateurs telle que
définie dans la norme ANSI/NFPA 75 Standard for Protection
of Electronic Computer/Data Processing Equipment
Trademarks
Each name of corporations or products in this book is either a registered trademark or a trademark of its respective corporation.
Remark
Any graphic and figure in this manual are subject to change without notice.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
All the safety and operating instructions should be read before
the product is operated.
This projector should be operated only from the type of power
source indicated on the marking label. If you are not sure of
the type of power supplied, consult your authorized dealer or
local power company.
Read all of the instructions given here and retain them for later
use. Unplug this projector from AC power supply before
cleaning. Do not use liquid or aerosol cleaners. Use a damp
cloth for cleaning.
Do not overload wall outlets and extension cords as this can
result in fire or electric shock. Do not allow anything to rest
on the power cord. Do not locate this projector where the
cord may be damaged by persons walking on it.
Follow all warnings and instructions marked on the projector.
For added protection to the projector during a lightning storm,
or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet. This will prevent damage
due to lightning and power line surges.
Do not attempt to service this projector yourself as opening or
removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service
personnel.
Unplug this projector from wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the projector.
Do not expose this unit to rain or use near water... for
example, in a wet basement, near a swimming pool, etc...
Do not use attachments not recommended by the
manufacturer as they may cause hazards.
c. If the projector has been exposed to rain or water.
d. If the projector does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the projector to normal operation.
e. If the projector has been dropped or the cabinet has been
damaged.
f. When the projector exhibits a distinct change in
performance-this indicates a need for service.
Do not place this projector on an unstable cart, stand, or table.
The projector may fall, causing serious injury to a child or
adult, and serious damage to the projector. Use only with a
cart or stand recommended by the manufacturer, or sold with
the projector. Wall or shelf mounting should follow the
manufacturer's instructions, and should use a mounting kit
approved by the manufacturers.
An appliance and cart combination should
be moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the appliance and cart
combination to overturn.
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer that have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock, or injury to persons.
Upon completion of any service or repairs to this projector,
ask the service technician to perform routine safety checks to
determine that the projector is in safe operating condition.
Slots and openings in the back and bottom of the cabinet are
provided for ventilation, to ensure reliable operation of the
equipment and to protect it from overheating.
The openings should never be covered with cloth or other
materials, and the bottom opening should not be blocked by
placing the projector on a bed, sofa, rug, or other similar
surface. This projector should never be placed near or over a
radiator or heat register.
Voor de klanten in Nederland
Bij dit produkt zijn batterijen
geleverd.
Wanneer deze leeg zijn, moet u
ze niet weggooien maar inleveren
als KCA.
This projector should not be placed in a built-in installation
such as a book case unless proper ventilation is provided.
NL
Never push objects of any kind into this projector through
cabinet slots as they may touch dangerous voltage points or
short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the projector.
Do not install the projector near the ventilation duct of air-
conditioning equipment.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
Air Circulation
Setup In Proper Directions
Openings in the cabinet are provided for ventilation and to
ensure reliable operation of the product and to protect it from
overheating, and these openings must not be blocked or
covered.
Use the projector properly in specified positions. Improper
positioning may reduce the lamp life and result in severe
accident or fire hazard.
This projector is allowed to project the picture in any position
of 360 degrees such as upward, downward, or backward as
below.
CAUTION
Hot air is exhausted from the exhaust vent. When using or
installing the projector, the following precautions should be
taken.
– Do not put any flammable objects near the vent.
– Keep the exhaust vent at least 3’(1m) away from any
objects.
– Do not touch a peripheral part of the exhaust vent,
especially screws and metallic part. This area will become
hot while the projector is being used.
– Do not put anything on the cabinet. The materials put on
the cabinet will not only get damaged but also cause fire
hazard by heat.
Bottom
Downward
(Usual)
Front
Upward
Bottom
Upward
Front
Downward
Cooling fans are provided to cool down the projector. This
projector monitors internal temperature and control the
running speed of the cooling fans.
Positioning Precautions
When installing the projector, avoid positioning it as
described below:
20˚
Do not tilt the projector more than 20
degrees above and below.
20˚
Exhaust Vent
(Hot air exhaust)
Do not put the projector on either
side to project an image.
In upward projection, do not tilt the
projector over 20 degrees right and
left.
Air Intake Vent
In downward projection, do not tilt
the projector over 20 degrees right
and left.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
Moving the Projector
Carry the projector by two or more people holding the carrying
handle.
Carrying Handle
Disconnect all the cables from the projector before
moving the projector. Moving the projector with the
cables connected may cause damage to the projector
or result in serious injury.
Retract the projector's adjustable feet and replace the lens cover
to protect the lens surface when moving the projector.
USE CAUTION IN CARRYING OR
TRANSPORTING THE PROJECTOR
Lens Cover
Replace the Lens cover when carrying or not
using the projector.
– Do not drop or bump a projector, otherwise damages or
malfunctions may result.
– When carrying a projector, use a suitable carrying case.
– Do not transport a projector by using a courier or
transport service in an unsuitable transport case. This
may cause damage to a projector. To transport a
projector through a courier or transport service, consult
your dealer for their information.
REMOVE LENS FROM THE PROJECTOR WHEN
CARRYING. OTHERWISE, IT MAY CAUSE SERIOUS
DAMAGE TO LENS AND THE PROJECTOR.
WHEN TRANSPORT OR STORE THE PROJECTOR
WITHOUT LENS, REPLACE THE LENS COVER
PLATE INITIALLY ATTACHED TO THE PROJECTOR.
TRANSPORTING OR STORING WITHOUT THE
LENS COVER PLATE MAY CAUSE DUST TO GET
INSIDE THE PROJECTOR AND RESULT IN
MALFUNCTION OF THE PROJECTOR OR DAMAGE
OF THE OPTICAL COMPONENTS INSIDE THE
PROJECTOR.
Do not place on an unflat surface and check no
object under the cabinet.
Caution in Handling the Projector
Do not hold the terminal cover when lifting or moving the projector, or may cause damage to the terminal cover or result in
personal injury.
Do not hold the lens when lifting or moving the projector, or may cause damage to the lens and the projector.
Be sure the surface is flat and no object is under the projector when placing the projector either side up. Uneven surface or
any object under the projector may cause damage to its cabinet. Especially be careful of the cabinet area around the
exhaust vent.
Do not hold the Cover.
Do not hold the Lens and the peripheral part.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Compliance
Federal Communication Commission Notice
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes
or modifications should be made, you could be required to stop operation of the equipment.
CAUTION
This is a Class A equipment. This equipment can cause interference in residential areas; in this case, the operator can be
asked to take adequate countermeasures.
AC Power Cord Requirement
The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.
AC Power Cord for the United States and Canada :
AC Power Cord used in the United States and Canada is listed by the Underwriters Laboratories (UL) and
certified by the Canadian Standard Association (CSA).
AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the plug will fit into
the power outlet. Do not try to defeat this safety feature. Should you be unable to insert the plug into the
outlet, contact your electrician.
GROUND
AC Power Cord for the United Kingdom :
This cord is already fitted with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of the plug. Should the
ASA
fuse need to be replaced, an ASTA approved BS 1362 fuse must be used of the same rating, marked thus
. If the fuse cover is
detachable, never use the plug with the cover omitted. If a replacement fuse cover is required, ensure it is of the same colour as that visible
on the pin face of the plug (i.e. red or orange). Fuse covers are available from the Parts Department indicated in your User Instructions.
If the plug supplied is not suitable for your socket outlet, it should be cut off and destroyed.
The end of the flexible cord should be suitably prepared and the correct plug fitted. (See Over)
WARNING : A PLUG WITH BARED FLEXIBLE CORD IS HAZARDOUS IF ENGAGED IN A LIVE SOCKET
OUTLET.
The Wires in this mains lead are coloured in accordance with the following code:
Green-and-yellow ············ Earth
Blue ································· Neutral
Brown ······························ Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in
your plug proceed as follows:
The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked by the letter E or by the safety
earth symbol
or coloured green or green-and-yellow.
The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
WARNING : THIS APPARATUS MUST BE EARTHED.
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparation
Parts Name
Front
q Remote Receiver
w Projection Lens (Option)
e Front Cover (inside Terminals)
r Speaker
t Carrying Handle
y Air Exhaust Vent
CAUTION
Hot air is exhausted from the exhaust vent.
Do not put heat-sensitive objects near this
side.
q
w
e
r
t y
CAUTION
This projector is equipped with cooling fans
for protection from overheating. Pay attention
to following to ensure proper ventilation and
avoid a possible risk of fire and malfunction.
Back
u
i
u
o
!
● Do not cover vent slots.
● Keep projector sides clear of any objects.
Obstructions may block cooling air.
u Indicators
i Top Controls
o Air Intake Vent
! Air Filter (inside)
! Speaker
! Lamp Cover
!
!
Bottom
!
! Adjustable Feet
!
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparation
Indicators
Press here to open the
Top Lid and then top
controls appear. (See next
page.)
q
w
e
r
t
y
u
q LAMP1 REPLACE indicator
t
y
READY indicator
Turns orange when the life of the projection lamp1
draws to an end. (p64, 69)
Lights green when the projector is ready to be turned on
and it remains green lighting while the projector is under
operation.
w WARNING TEMP indicator
Blinks green in Power Management mode or when the
projector is shutdown due to power failure.
Blinks red when the internal temperature of the
projector is abnormally high. (p62,67)
SHUTTER indicator
Lights blue when the shutter is released. (p68)
e WARNING FILTER indicator
Lights orange when the projector's filter is clogged with
dust. (p63, 68)
u LAMP2 REPLACE indicator
Turns orange when the life of the projection lamp2
draws to an end. (p64, 69)
r LAMP indicator
Lights red when the projector is in the stand-by mode,
and turns dim lighting when the projector is turned on.
(p67)
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparation
Top Control
w
e
r
t
y
u
q
AUTO
PC ADJ.
LENS
SHIFT
INPUT
MENU
INFO.
ZOOM
FOCUS
SHUTTER
CANCEL
SELECT
P
POWER
!
!
!
o
i
q LENS SHIFT button
t
INFO. button
Displays Information. (p31)
Activates Lens shift function. (p30)
y AUTO PC ADJ. button
w MENU button
Operates the Auto PC adjustment function. (p31)
Opens or closes the On-Screen Menu. (p34, 35 )
u INPUT button
e CANCEL button
Switches input sources. (p31)
Cancels the selection and returns to the previous menu.
r Control pad
i SHUTTER button
Navigates through the menu or adjusts value in the On-
Screen Menu. These are also used to pan the image in
the Digital zoom + mode. (p33, 34, 35)
Releases and opens up the built-in shutter to block out
light. (p30)
o POWER ON-OFF button
Turns the projector on or off. (p28, 29)
About Control Pad
The built-in Control Pad is
! SELECT button
a
Executes the item selected. It is also used to expand/
semiconductive touchpad operational
with light finger touch. Glide your finger
up, down, right and left on the pad to go
to the desired menu, adjust values and
operate various convenient features.
Refer to the following pages for
respective directions.
compress the image in Digital zoom +/– mode. (p33, 34,
35)
! FOCUS button
Adjusts focus of the image. (p30)
! ZOOM button
Adjusts zoom of the image. (p30)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparation
Terminals
w
INPUT 3
R-AUDIO-L
INPUT 1
DIGITAL (DVI-D)
ANALOG IN
ANALOG OUT
AUDIO 1
AUDIO 2
q
r
e
(MONO)
S-VIDEO
INPUT 2
R
G
B
H/V
V
VIDEO/Y Cb/Pb Cr/Pr
VIDEO/Y Cb/Pb
Cr/Pr
e INPUT 3 terminals
q INPUT 1 terminals
AUDIO (R-L)
AUDIO 1
Connect the audio output from video equipment
connected to VIDEO/Y Cb/Pb Cr/Pr jacks or S-VIDEO
jack to these jacks. (When the audio output is
monaural, connect it to L(MONO) jack. (p24, 25)
Connect the audio output from a computer or video
equipment connected to DIGITAL (DVI-D) or ANALOG
IN terminal to this jack. (p22, 24)
DIGITAL (DVI-D) (HDCP compatible)
VIDEO/Y, Cb/Pb, and Cr/Pr
Connect digital output signal from a computer or
video equipment to this terminal with a DVI-D cable.
(p22, 24)
Connect video or component output (Y, Cb/Pb and
Cr/Pr) from video equipment to these jacks with a
video cable (RCA-type). (p24, 25)
ANALOG IN
S-VIDEO
Connect analog output signal from a computer or a
video equipment (Component or RGB Scart) to this
terminal with a VGA cable, a Scart-VGA or a
Component-VGA cable. (p22)
Connect S-Video output from video equipment to this
jack. (p24)
r INPUT 2 terminals
w ANALOG OUT
This terminal can be used for analog signal output
incoming through the ANALOG IN terminal (INPUT 1).
Connect this terminal to the other monitor with a VGA
cable. (p22)
AUDIO 2
Connect the audio output from video equipment
connected to VIDEO/Y, Cb/Pb, and Cr/Pr jacks or G,
B, R, H/V, and V jacks to this jack. (p22, 25)
VIDEO/Y, Cb/Pb, and Cr/Pr
Connect video or component output (Y, Cb/Pb and
Cr/Pr) from video equipment to these jacks with a
video cable (BNC-type). (p25)
G, B, R, H/V, and V
Connect RGB output signal from a computer with a
computer cable (5 BNC-type) to these jacks. (p22)
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparation
q
w
e
u
y
t
r
✽
q INPUT 4 (WARP & BLENDING board)
e R/C JACK
Connect the remote control to this jack with the supplied
remote control cable to use the remote control as wired.
(p26)
DIGITAL (DVI-D) (HDCP compatible)
Connect digital output signal from a computer or
video equipment to this terminal with a DVI-D cable.
(p23)
r USB
Connect a USB mouse (commercially available) to
control On-Screen Menu. (p26)
SERIAL PORT IN
When operating Warp and Blending feature, connect
serial port of the computer and this terminal with a
serial cross cable (commercially supplied). (p23)
t USB (Series B)
This port is used for the projector maintenance.
SERIAL PORT OUT
When using Warp and Blending feature for more than
two projectors from a computer connected to the
SERIAL PORT IN terminal above, connect SERIAL
PORT IN terminal on the other projector and this
terminal with a serial cross cable (commercially
supplied). (p23)
y SERIAL PORT OUT
This terminal outputs signal from SERIAL PORT IN.
When controling more than two projectors from a
computer, connect the other projector to this terminal
with a serial cross cable (commercially supplied).
✔Note:
Refer to the enclosed operation manual for Warp and Blending in Advanced
Screen Manager.
u SERIAL PORT IN
When controling the projector from a computer, connect
the computer to this terminal with a serial cross cable
(commercially supplied).
w INPUT 5 (Vacant for Optional Interface Board)
Optional interface board can be installed into this slot.
This input accepts digital signals only. (p21, 75)
A built-in micro processor which controls this unit may occasionally
✽
malfunction and need to be reset. This can be done by pressing the RESET
button with a pen, which will shut down and restart the unit. Do not use the
RESET function excessively.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparation
Remote Control
t
y
u
SHUTTER D.ZOOM ON-OFF
q
KEYSTONE
w
e
i
!
ZOOM
FOCUS
LENS SHIFT
o
r
q SHUTTER button
y D.ZOOM button
Releases the built-in shutter for light blocking. (p30)
Activates D.Zoom +/– function. (p33)
w
e
KEYSTONE button
u POWER ON-OFF button
Corrects keystone distortion. (p32)
Turns the projector on or off. (p28, 29)
LENS SHIFT button
Activates LENS SHIFT function. (p30)
i FOCUS buttons
Adjust focus of the image. (p30)
r CONTROL PAD (semiconductive touchpad)
Selects an item or adjusts value in the On-Screen Menu.
This is also used to pan the image in the Digital zoom +
mode. (p33)
o ZOOM buttons
Adjust zoom of the image. (p30)
! SELECT button
t WIRED REMOTE JACK
Executes the item selected.
Connect the Remote Control Cable to this jack.
Battery installation is required regardless if it is used as
wired or wireless. (p16, 26)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparation
i
o
CANCEL
INFO
MENU
AUTO PC
SCREEN
q
w
e
!
!
FREEZE
VOL.
SOUND
MUTE
P-TIMER
INPUT
1
!
r
t
y
INPUT
INPUT
4
5
INPUT
INPUT
2
3
CH
REMOTE
ID
!
!
u
REMOTE RESET ON ALL OFF
o INFO button
q MENU button
Displays the projector information. (p31)
Opens or closes the On-Screen Menu. (p34, 35)
! AUTO PC button
w FREEZE button
Operates the Auto PC adjustment. (p31)
Freezes the projected picture. (p32)
e VOL. button
! SCREEN button
Adjusts volume. (p33)
Selects screen sizes. (p32)
r MUTE button
!
!
INPUT 1-3 buttons
Mutes sound. (p33)
Selects input source (INPUT 1 - INPUT 3). (p31)
t CH button
INPUT 4-5 buttons
Selects input source (INPUT 4 - INPUT 5). (p31)
Switches Remote Control Channel (CH). (p16)
y ID button
! REMOTE RESET/ON/ALL-OFF switch
Switches Remote Control ID. (p16)
When using the remote control, set this switch to “ON.”
Set it to “ALL OFF” for power saving when it is not
used. Slide this switch to "RESET" with holding down
the CH and ID buttons at the same time to initialize the
Remote Control ID and CH. (p16)
u
P-TIMER button
Operates P-Timer function. (p32)
i CANCEL button
Cancels the selection and returns to the previous menu.
(p34)
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparation
Remote Control Transmitter
This wireless remote control uses radio frequency signal. You can switch four frequency channels prepared and select a
remote control ID from eight IDs. The Remote Control Channel selection prevents radio frequency interference from the
other equipment and the Remote Control ID selection allows you to operate several projectors with their respective remote
controls without mutual interference among those projectors.
Wired Remote Control Transmitter
The remote control can be used as a wired remote control. When
interference between the projector and other equipment occurs or
the projector is used in a place where the operation of radio
equipment is restricted, connect the remote control and the
projector with the remote control cable provided. Connected with
the remote control cable, the remote control does not emit radio
signal.
Remote Control Channel and ID Setup
CANCEL
Initial Remote Control Channel and ID are CH1 and ID1. When
you change the setting, set a Channel first, and then an ID.
MENU
AUTO PC
SCREEN
INFO
FREEZE
VOL.
Channel and ID settings for the remote control should be the
same as those for the projector. When changing the CH and ID
settings to the remote control, do it to the projector as well. Refer
to "Remote Control " in Setting menu on page 53.
SOUND
MUTE
P-TIMER
INPUT
1
INPUT
INPUT
4
5
INPUT
INPUT
2
3
CH
CH button
ID button
REMOTE
ID
Should you be lost at which CH and ID are currently set, initialize
the Channel and ID once, and set them again.
REMOTE RESET ON ALL OFF
Set the Remote Control Channel
1
With holding down the CH button, press the SELECT button.
The Remote Control Channel switches sequentially for one
pressing the SELECT button. (See Table1 on next page.)
SELECT button
2
Set the Remote Control ID
While pressing the CH/ID
button, press the SELECT
button number of times
corresponding to the
remote control CH/ID.
With holding down the ID button, press the SELECT button.
The Remote Control ID switches sequentially for one
pressing the SELECT button. (See Table2 on next page.)
Initialize the Remote Control Channel and ID
With holding down the CH and ID buttons together, slide the
REMOTE RESET/ON/ALL-OFF switch to REMOTE RESET,
and then to ON. The initial Channel and ID are CH1 and ID1.
(p15)
✔Note:
Remote Control Channel and ID cannot be initialized separately.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparation
Channel switches sequentially for
one pressing the SELECT button.
ID switches sequentially for one
pressing the SELECT button.
Remote Control CH
Radio Frequency
Remote Control ID
CH 1 ✽
CH 2
ID 1 ✽
ID 2
ID 3
ID 4
ID 5
ID 6
ID 7
ID 8
2.472 GHz
2.403 GHz
2.446 GHz
2.421GHz
CH 3
CH 4
Table1: Remote Control Channel & Frequency
✽ Default setting
Table2: Remote Control ID
Caution about Radio Wave
The remote control operates in 2.4 GHz band, the same frequency band used for industrial, scientific, and medical
equipment (such as pacemaker), as well as amateur radio stations.
Before operating the remote control, make sure no electromagnetic interference occurs and pay attention to the
following cautions.
1. Be sure that there are no other devices in the area that may use the same frequency band as the remote
control.
2. If any other devices are causing radio interferences, change the communication frequency channel or
move to other location.
Caution in Wireless LAN Interference
Under wireless LAN environment based on IEEE 802.11b and IEEE802.11g, the remote control may not operate
properly due to radio interferences. The remote control is initially set to use 2.472 GHz band (CH1) corresponding
to several channels of wireless LAN.
Should the remote control not operate properly due to radio interference, switch the communication frequency
channel to CH2. Yet the operating condition is not improved, try CH3 and CH4. In case of failure in every channel
operation, relocate other radio equipment using 2.4 GHz band away from the remote control and the projector.
Remote Control Battery Installation
Remove the battery
compartment lid.
Slide the batteries into
the compartment.
Replace the compartment
lid.
1
2
3
Two AA size alkaline
batteries
For correct polarity (+ and
–), be sure battery
terminals are in contact
with pins in compartment.
Press the lid downward
and slide it.
To insure safe operation, please observe the following precautions :
● Use (2) AA, UM3 or LR6 type alkaline batteries.
● Replace two batteries at the same time.
● Do not use a new battery with a used battery.
● Avoid contact with water or liquid.
● Do not expose the remote control to moisture, or heat.
● Do not drop the remote control.
● If a battery has leaked on remote control, carefully wipe case clean and install new batteries.
● Risk of explosion if battery is replaced by an incorrect type.
● Dispose of used batteries according to the instructions.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installation
Install the projector in a safe place. Before installation, read Safety
Instructions thoroughly and check the installation place. Install the
projector in a place with sufficient strength to support the
projector's weight. Installation on an unstable stand, cart, or
ceiling may cause serious injury or accidents.
Do not place the projector where is extremely hot and humid. Do
not place the projector where is dusty and smoky. When installing
the projector in dusty and smoky places or in a place for a long
period of time, installation with Smoke Resist Box (POA-SR-140)
separately supplied is recommended. (p75)
Lens Installation
Before setting up the projector, install optional lens in the
projector. Install the lens following the instructions in the Lens
Installation Manual provided. Ask the sales dealer for detailed
information of optional lens specifications.
Do not move the projector with holding the lens mounted and its
peripheral part. It may cause serious damages to the projector and
the lens.
When moving or setting up the projector, check the
followings again:
– Be sure that the lens is securely installed into the
projector.
– Be sure to replace Lens cap to protect lens
surface.
– Be careful not to hold or subject a lens to strong
forces. It may damage lens, cabinet, or
mechanical parts.
Lens cap
Positioning the Projector
This projector is designed to project on a flat surface. Projector
should be perpendicular to the projection screen. Otherwise, the
projected image may be distorted. Keystone function allows you
to correct image distortions, but it should be considered that the
keystone correction may lower the image resolution. (p32)
Do not expose the projection screen to direct sunlight or
excessive ambient lighting. The projected image may get white-
tinged due to reflection and the best image quality may not be
obtained.
SCREEN
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Lens Shift Adjustment
Lens shift feature is provided to move the position of the projected image vertically by 50% and horizontally by 10%
respectively without any image distortion.
✽ Lens shift range varies depending on lens and projectors. The range in this manual is the case of LNS-W04.
10%
10%
50%
50%
Level Adjustable Feet
This projector has four level adjustable feet. The projection angle
can be adjusted by rotating each foot. Adjust the four feet to
obtain best position of the projected image and make the
projector stable.
The projection angle is adjustable up to 3.65 degrees upward and
downward respectively by rotating front and back feet.
The projector can project image vertically and horizontally in the
range of 360 degrees. For proper installation, refer to Setup In
Proper Directions on page 6.
Adjustable feet
3.65°
3.65°
Projection angle is adjustable up to 3.65 degrees
upward and 3.65 degrees downward by adjusting front
and back feet.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Connecting AC Power Cord
This projector uses nominal input voltages of 120 V or 200-240 V
AC. This projector automatically selects correct input voltage. It is
designed to work with single-phase power systems having a
grounded neutral conductor. To reduce risk of electrical shock, do
not plug into any other type of power system.
Consult your authorized dealer or service station if you are not sure
of type of the power being supplied.
Connect a projector with peripheral equipment before turning on it.
(Refer to p22 ~ 25 for connection.)
Main On/Off switch
CAUTION
AC power socket
For safety, unplug AC power cord when the projector is not in
use. When this projector is connected to an outlet with AC
power cord and the Main On/Off switch is on, the projector is in
stand-by mode and consumes a little electric power.
Connect AC Power Cord (supplied) to
this socket. AC outlet must be near
this equipment and must be easily
accessible.
NOTE ON POWER CORD
AC Power Cord must meet requirement of the country where you use the projector.
Confirm an AC plug type with the chart below and a proper AC power cord must be used.
If the supplied AC Power Cord does not match your AC outlet, contact your sales dealer.
Projector side
AC Outlet side
For the U.S.A. and Canada
For Continental Europe
For the U.K.
Ground
To POWER CORD
CONNECTOR on a
projector.
To the AC Outlet.
(200 - 240 V AC)
To the AC Outlet.
(120 V AC)
To the AC Outlet.
(200 - 240 V AC)
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Connection Terminals
Front cover
Terminals to connect AC power cord and other equipment are
located in the front part of the projector for easy setup. The
terminal area is masked with the front cover to protect them from
dust and others, and hide messy cable connections.
Remove and replace the front cover following the procedure
below:
Pushing the button A on right side of the front cover, pull the part
forward to remove the front cover.
A
To replace the front cover onto the projector, insert back the left
part of the cover into the projector and then push the entire cover
back the projector. Make sure the front cover is locked with the
button A and fit on the projector.
Pull this part forward
with pushing button A.
Caution
Do not push hard or give a strong shock to the
cover. It may cause damage to it.
Terminals
Interface Board Slots
The projector's front terminal area has two replaceable Interface
board slots. The projector's functions can be extended by
installing the optional interface boards into the terminal slots. A
vacant slot (Input 5) is provided in your purchasing the projector.
Socket
Terminal board
Install or replace the optional interface boards as follows:
Remove 2 screws from an interface board installed in the
projector.
Pull out the interface board by holding its handles and remove it.
Then, insert another board along with the guides inside the slot to
fit the socket into the inside plug. Tighten screws to secure the
board.
Screws
✔Note:
When installing or removing the interface board, disconnect the AC power cord from
the AC outlet before doing it.
Option Control No.
✔Notes On Ordering or Using Optional Interface Boards:
When ordering or using the Optional Interface Boards, contact your sales dealer and
tell the Model no. of your desired board (p75) and Option Control No. shown in the
Information menu. (p31and 61)
See Option Control No. in the Information menu
to order any optional interface board.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Connecting to Computer (Digital and Analog RGB)
Cables used for connection
q VGA Cable (HDB 15 pin)
w DVI-D Cable
t Audio Cables (Mini Plug: stereo) ✽
(✽ = Not supplied with this projector.)
e BNC Cable ✽
r Serial Cross Cable (RS-232C) ✽
PC Serial Port
Audio Output Monitor Output
Monitor Output
Monitor Input
Monitor Output
Audio Output
r✽
t✽
w
q
q
e
t✽
ANALOG IN
ANALOG OUT
R
G
B
H/V
V
AUDIO 2
(Stereo)
AUDIO 1
(Stereo)
DIGITAL (DVI-D)
Other Projector
SERIAL PORT IN
SERIAL PORT IN
SERIAL PORT OUT
r✽
Note:
When connecting the cable, the power cords of both the projector and
the external equipment should be disconnected from AC outlet.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Connecting to Digital PC/AV Equipment (Warp & Blending)
Cables used for connection
q DVI-D Cable
w Serial Cross Cables (RS-232C) ✽
(✽ = Not supplied with this projector.)
Refer to the enclosed operation manual for details in operation of
the Warp & Blending feature.
Digital Output
PC Serial Port
Other Projector
SERIAL PORT IN
q
w✽
w✽
DIGITAL (DVI-D)
SERIAL PORT IN
SERIAL PORT OUT
✔Note:
Connect digital PC/AV source to the DIGITAL (DVI-D) terminal with a DVI-D cable to
adjust projected images from the computer connected to the SERIAL PORT IN
terminal with Warp and Blending feature.
Note:
When connecting the cable, the power cords of both the projector and
the external equipment should be disconnected from AC outlet.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Connecting to Video Equipment (Digital and Video)
Cables used for connection
q Video Cable ✽
w S-Video Cable ✽
e DVI-D Cable
r Audio Cables (RCA x 2, Mini Plug: stereo) ✽
(✽ = Not supplied with this projector.)
Audio Output Digital Output
Video Output
Audio Output
(R) (L)
S-Video Output
(Stereo)
(HDCP compatible)
r ✽
e
q✽
r✽
w✽
AUDIO 1
(Stereo)
DIGITAL (DVI-D)
S–VIDEO
AUDIO (R) (L)
VIDEO
INPUT 3
R-AUDIO-L
(MONO)
S-VIDEO
VIDEO/Y Cb/Pb Cr/Pr
Note:
When connecting the cable, the power cords of both the projector and
the external equipment should be disconnected from AC outlet.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Connecting to Video Equipment (Component and RGB Scart)
Cables used for connection
q BNC Cable ✽
w Scart-VGA Cable ✽
e Component Cable ✽
r Audio Cables (Mini Plug (stereo) + RCA x 2, or RCA x 1) ✽
(✽ = Not supplied with this projector.)
Audio Output
(R) (L)
Component
Video Output
(Y, Pb/Cb, Pr/Cr)
Audio Output
(R) (L)
RGB Scart
21-pin Output
Component Video Output Audio Output
(Y, Pb/Cb, Pr/Cr)
(R) (L)
r✽
q✽
r✽
w✽
e✽
r✽
AUDIO 1
(Stereo)
AUDIO 2
(Stereo)
ANALOG IN
Y
Cb/Pb Cr/Pr
AUDIO
Y
Cb/Pb Cr/Pr
(R) (L)
INPUT 3
R-AUDIO-L
(MONO)
VIDEO/Y Cb/Pb Cr/Pr
Note:
When connecting the cable, the power cords of both the projector and
the external equipment should be disconnected from AC outlet.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Operating the Projector
You can operate the projector with the projector's top control, the remote control or a USB mouse (not provided). The
remote control is available as wireless and wired.
Operational range of the wireless remote control is within about 32.8' (10m) from the projector. Operational range differs
depending on environments where the projector is used. Any obstruction to air signal between the projector and the
remote control may prevent the remote control from working properly.
Wireless Remote Control Operation
Wired Remote Control Operation
R/C jack
Remote control
cable
Connect the R/C JACK on the projector and the remote
control with the remote control cable when operating
the remote control as wired.
The wireless remote control does not work
when the remote control cable is
connected to either the projector or the
remote control. Remove the remote
control cable from both of the projector and
the remote control when using it as
wireless.
Mouse Operation
Projector Top Control Operation
USB terminal
Connect the USB terminal on the projector and a USB
mouse when operating the projector's menu with the
USB mouse. A mouse cursor will appear on the
screen with the mouse connected.
Mouse operation offers the On-Screen Menu control
only. Other operations are unavailable with the USB
mouse. For details of the mouse operation, refer to
page 34~35.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Basic Operation and Reference Buttons
For detail operations other than those on this page, follow the respective menu operations described later.
Top Control
Remote Control
Operations & Buttons
Ref. Pages
28, 29
On-Off
Lens Shift
Zoom
Pad
Pad
➔
➔
➔
➔
30
Pad
Pad
(
(
)
)
30
ed
ed
Focus
30
Shutter
30, 55
Auto PC Adjust
Input Selection
31, 41
(Input 1–5)
31, 37~38
Information
Keystone
Screen Selection
Freeze
31, 61
32, 49
32, 48
32
Pad
–
–
–
–
–
–
–
–
➔
P-Timer
32
Pad
D. Zoom
➔
33, 49
16, 17
33
Remote CH and ID
Volume
Pad
➔
Mute
33
Menu
Select
Cancel
34~36
These buttons are used on the
menu operations.
These buttons are used on the
menu operations.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Turning On the Projector
Complete peripheral connections (with Computer, VCR, etc.)
before turning on the projector. (Refer to page 22~25 for
connection.)
1
16
Turn on the MAIN On/Off switch of the projector. The
LAMP indicator lights red, and the READY indicator lights
green.
2
3
The preparation display disappears after 20 seconds.
Press the POWER ON-OFF button on the top control or the
remote control. The LAMP indicator dims, and the cooling
fans start to operate. The preparation display appears on the
screen and count-down starts. The input and source
selected last appears after 20 seconds count-down.
Selected Input and Source
If the projector is locked with a PJ PIN code, PJ PIN code
Input Dialog Box will appear. Enter the PIN code as
instructed below.
(See page 37~38 for Input)
Enter a PJ PIN code
Select a number by softly tapping the control pad and fix the number with
the SELECT button. The number will change to "✳". If you fixed a wrong
number, move the yellow frame pointer to "C" or "Ent" once, then enter the
correct number again.
PJ PIN code Input Dialog Box
Repeat this step to complete entering a four-digit number.
When the four-digit number is fixed, move the yellow frame pointer to
"Ent". Press the SELECT button so that you can start to operate the
projector.
Pointer(yellow frame)
If you entered a wrong PIN code, the entered number (✳✳✳✳) will turn red
and disappear. Enter a correct PIN code all over again.
What is PIN code?
PIN code is a security code using Personal Identification Number that
allows the person who knows it to operate the projector. Setting PIN code
prevents the projector from being operated by an unauthorized person.
A PIN code consists of a four-digit number. Refer to Security in Setting on
page 57 for locking operation of the projector with your PIN code.
CAUTION ON HANDLING PIN CODE
If you forget your PIN code, the projector can no
longer be started. Set a new PIN code with special
care, write it down in column on page 81 of this
manual, and keep it at hand. Should the PIN code be
missing or forgotten, consult your sales dealer or the
service station.
After the OK icon
disappears, you can
operate the projector.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Turning Off the Projector
Press the POWER ON-OFF button on the top control or the
remote control, and a message "Power off?" appears on the
screen.
1
Press the POWER ON-OFF button again to turn off the
projector. The LAMP indicator brightly lights red and the
READY indicator goes out. After approximate 90 seconds,
the READY indicator will light green again and then the
projector can be turned on by pressing the POWER ON-OFF
button.
2
The message disappears after 4 seconds.
The Cooling fans operate for approximate 2 minutes after the
projector is turned off; keep operating more 30 seconds after
the READY indicator lights green. To power down the
projector completely, turn off the MAIN On/Off switch and
disconnect the AC Power Cord.
3
TO MAINTAIN THE LIFE OF LAMP, ONCE YOU TURN
PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE
TURNING IT OFF.
DO NOT DISCONNECT AC POWER CORD WHILE
COOLING FANS ARE RUNNING OR BEFORE POWER
INDICATOR LIGHTS RED. OTHERWISE IT WILL
RESULT IN SHORTENING LAMP LIFE.
✔Note:
• The projector cannot be turned on for about 90 seconds after turned off. You can
turn it on again after the READY indicator lights green.
• When the On start function is on, this projector is turned on automatically by
connecting the AC power cord to an AC outlet. (See page 54 for the On start
function.)
• Do not operate the projector continuously without rest. Continuous use may result
in shortening the lamp life. Turn off the projector and give it a rest about an hour in
every 24 hours.
• This projector monitors internal temperature and automatically controls the running
speed of the cooling fans.
• If the WARNING TEMP indicator blinks red or all the indicators except the LAMP
indicator are blinking, see “Warning Temp Indicator” on page 62.
• When “Power management” mode is Ready or Shut down, projector detects signal
interruption and turns off the Projection Lamp automatically after the set time has
passed. Refer to “Power management” on page 54.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Lens Shift Adjustment
Press the LENS SHIFT button and adjust with the Control pad.
• When the lens position comes right in center
vertically, the vertical arrows turn red.
• When the lens position comes right in center
horizontally, the horizontal arrows turn red.
Zoom and Focus Adjustment
Top Control
Press the ZOOM/FOCUS button and adjust with the Control pad.
Remote Control
Press the ZOOM/FOCUS ed button to adjust Zoom and Focus.
Shutter Function
Shutter function allows you to completely block out light to the
screen. Press the SHUTTER button to release the shutter inside
the projector. To open up the shutter, press the SHUTTER button
again. Refer to p55~56 for detail of setting for the Shutter
function.
Remote Control
SHUTTER D.ZOOM ON-OFF
SHUTTER button
KEYSTONE
ZOOM
FOCUS
LENS SHIFT
✔Note:
Top Control
• The SHUTTER buttons on the top control and the remote control can not be
effective when Shutter Protection is "On" in the Setting menu. (p55)
• The SHUTTER indicator on the projector's top lights blue when the shutter is
released. (p10)
AUTO
PC ADJ.
INPUT
• When the Shutter level is "High contrast" in the Setting menu, the shutter opens up
80%. (p55)
• The projector will shut down automatically when the set time on Shutter
management has passed. (p56)
INFO.
SHUTTER
SHUTTER button
POWER P
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Input Selection
Choose either Input 1, Input 2, Input 3, Input 4, or Input 5 by
pressing the INPUT button on the top control or the INPUT 1,
INPUT 2, INPUT 3, INPUT 4, or INPUT 5 button on the remote
control.
INPUT button
Input 1
Before using these buttons, correct input source should be
selected through menu operation as described on p37~38.
Input 2
Input 3
Input 4
Input 5
Auto PC Adjustment
Auto PC Adjustment function is provided to automatically adjust
Fine sync, Total dots, Horizontal, and Vertical picture position to
conform to your computer by just pressing the AUTO PC ADJ. on
the top control or the AUTO PC button on the remote control.
✔Note:
• Fine sync, Total dots and Picture Position of some computers can not be fully
adjusted with this Auto PC Adjustment function. When the image is not provided
properly with this operation, manual adjustments are required. (p42, 43)
• Auto PC Adjustment function cannot be operated in Digital Signal input on DVI
terminal and “480i”, “575i”, “480p”, “575p”, “720p (HDTV)”, “1035i (HDTV)”,
“1080i/50 (HDTV)” or “1080i/60 (HDTV)” is selected on System menu (P40).
Information
Information display can be used to confirm the current operating
condition of the projector and the signal being projected through
the projector.
Press the INFO button to display Information window on screen.
To hide the Information window, press the INFO button again.
Use this menu to check the projector's operating condition when
you face troubles in operation. Refer to the Information menu on
page 61.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Keystone Adjustment
Keystone function is provided to correct image distortions.
Press the KEYSTONE button and correct vertical and horizontal
distortions with the Control pad. The Keystone adjustment can be
memorized. (p49)
✔Note:
Horizontal keystone is ineffective for PLC-EF60.
• The arrows are white when there is no correction.
• The arrows disappear at the maximum correction.
• The direction of the arrow being corrected turns red.
• If you press the KEYSTONE button on the remote
control once again while the keystone dialog box is
being displayed, the keystone adjustment will be
canceled.
Screen Selection
Select a screen size among Normal, Wide, True, Full screen and
Custom by pressing the SCREEN button on the remote control.
Refer to the Screen menu on p48 for details of each screen
setting.
SCREEN button
Normal
Wide
True
✔Note:
True cannot be selected when selecting AV sources for the Input.
Full screen
Custom
Picture Freeze Function
Press the FREEZE button on the remote control to freeze the
picture on screen. To cancel the Freeze function, press the
FREEZE button again or press any other button.
P-Timer Function
Press the P-TIMER button on the remote control. The timer
display “00 : 00” appears on the screen and the timer starts to
count time (00 : 00 ~ 59 : 59).
To stop the P-Timer, press the P-TIMER button. And then, press
the P-TIMER button again to cancel the P-Timer function.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
D. Zoom +/– Function
D. Zoom +
Press the D. ZOOM button on the remote control once and then
expand the image size with the SELECT button and pan the image
with the Control pad.
D. Zoom –
Press the D. ZOOM button on the remote control twice and then
compress the image size with the SELECT button.
✔Note:
To exit the D. Zoom +/– mode, try the followings:
• To return to the normal screen, change Input, or change the screen size.
• To exit the panning mode, press any button except the D. ZOOM button, the
SELECT button, and the CH and ID buttons.
Volume Control
indicates approximate
level of volume.
Volume
Press the VOL button on the remote control. The volume dialog
box appears on screen. Adjust volume with the Control pad.
Mute
Press the MUTE button on the remote control to cut off sound.
To restore sound to its previous level, press the MUTE button
again or press the VOL button and change volume level with the
Control pad.
Press the MUTE button to set
the Mute function On or Off.
The display disappears after 4 seconds.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
How to Operate On-Screen Menu
The projector can be adjusted or set via the On-Screen Menu.
Refer to the following pages for respective adjustment and setting
procedure.
Top Control
MENU button
Top Control/Remote Control Operation
Press the MENU button on the projector's top control or the
1
LENS
SHIFT
MENU
remote control to display the On-Screen Menu.
ZOOM
FOCUS
CANCEL
SELECT
Softly tap the Control pad on the top control or the remote
control to spin Menu icons. When a desired Menu icon
comes right in front, press the SELECT button to display
Sub-menu.
CANCEL button
SELECT button
2
Select an item to adjust by softly tapping the Control pad or
gliding your finger on the Control pad.
3
Press the SELECT button to show the item data. Adjust the
data or select a desired setting by your fingertip operation on
the Control pad.
4
Control pad
Remote Control
✔Note:
• The selected item is not in effect until the SELECT button is pressed.
ZOOM
FOCUS
LENS SHIFT
• To return to the previous menu or cancel the selection, press the CANCEL button.
Control pad
Mouse Operation
CANCEL
INFO
MENU
AUTO PC
SCREEN
Left click your mouse to display the On-Screen Menu.
1
FREEZE
VOL.
SOUND
P-TIMER
INPUT
1
Select a Menu icon with the mouse pointer and one left click
to display the submenu or with clicking 78 or 77 88 to
spin Menu icons and click ENTER when a desired Menu icon
is right in front.
SELECT button
2
CANCEL button
MENU button
Click an item to show the item data to adjust or the dialog
box to select a setting.
3
Adjust the data with clicking ed or moving up or down the
right bar or click a desired setting.
4
✔Note:
To return to the previous menu or cancel the selection, right click your mouse.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
On-Screen Menu
Menu icon
Guide
Currently selected menu.
Control bar for Mouse Operation
This bar appears when a USB mouse is connected to
the USB terminal of the projector.
Mouse cursor
When clicking on 77 or 88 on the control bar, menu
icons rotate fast. When clicking on 7 or 8, menu
icons rotate one by one by every left clicking.
SELECT
button
When a desired Menu icon comes right in front, click
SELECT or press the SELECT button on the remote
control or the top control.
Pointer
(yellow frame)
Move the pointer to select an item with the Control
pad and press the SELECT button or by mouse
clicking. The selected item box will turn yellow.
Navigate through items with the Control pad or the
mouse cursor and the next menu will automatically be
displayed.
Item data
Click the Point ed or move the bar
to adjust value.
Quit
To exit this menu.
Item
The item being selected.
✔Note:
The Control bar for mouse operation and the Mouse cursor do not
appear with no USB mouse connected to the projector. (p26)
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Menu Icons and Their Features
The projector can be adjusted or set via the On-Screen Menu. Refer to the following pages for respective adjustment and
setting procedure.
Menu icons
What You Can Do with Each Menu
Page no.
INPUT :
selects input sources. Before selecting input sources with the top
control or the remote control, correct input source should be selected
through menu operation.
37~38
SYSTEM :
selects system of the connected computer and video sources.
39~40
41~43
PC ADJ. :
adjusts several features precisely for the projector to conform to your
computer's signal format and project optimum image.
IMAGE :
selects image levels suitable for the connected image source and allows 44
you to select the image data stored in Image Adjust Menu.
IMAGE ADJ. :
SCREEN SETTING :
SOUND :
adjusts each picture component of the projected image in detail and
store the adjusted image data in the projector to reproduce the
customized image quality anytime.
45~47
selects screen aspect, adjusts vertical and horizontal scales, picture
position, sets the projection method (Ceiling and Rear), and activates
keystone and digital zoom functions.
48~49
50
adjusts sound that the projector's speakers reproduce.
SETTING :
sets up operating environment for various features of the projector.
51~58
SPECIAL :
sets up operating environment of the projector and serves to the
projector's maintenance.
59~61
61
INFORMATION :
displays current setting information and operating conditions of the
projector, and allows you to check under what condition the projector is
operating.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Input
Input
selects computer and video input sources.
Press the MENU button to display the On-Screen Menu.
Spin the menu icons with the Control pad and press the
SELECT button when the INPUT icon comes right in front.
Input Menu
1
2
3
Move the yellow frame pointer with the Control pad to a
input which you want to select.
Input icon
Move the pointer
(yellow frame) to
an input that you
want to select and
press the SELECT
button.
Press the SELECT button to display Source Select Menu for
the input selected.
Select a source from the Source Select Menu.
The item being selected.
Input 1
Input 1
Move a pointer to Input 1 and press the SELECT button.
Source Select Menu
When the input source is analog coming from a
computer through the Input 1 (ANALOG IN)
terminal, select RGB (PC Analog).
RGB (PC Analog)
Move the pointer to
RGB(PC Analog), RGB
(Scart), RGB(PC Digital),
or RGB(AV HDCP) and
press the SELECT
button.
When the input source is coming from video
RGB (Scart)
equipment connected to the Input 1 (ANALOG
IN) terminal with a Scart-VGA Cable, select RGB
(Scart).
When the input source is digital coming from a
computer through the Input 1 (DVI) terminal,
select RGB (PC Digital)
RGB (PC Digital)
When the input source compatible with HDCP
is coming from video equipment through the
Input 1 (DVI) terminal, select RGB (AV HDCP).
RGB (AV HDCP)
✔Note:
HDCP (High-bandwidth Digital Content Protection) is a system for protecting digital
entertainment content delivered by DVI (Digital Visual Interface) from being copied.
The specification of HDCP is decided and controlled by Digital Content Protection,
LLC. Should the specification be changed, this projector may not display the digital
content protected by HDCP.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Input
Input 2
Move a pointer to Input 2 and press the SELECT button.
Source Select Menu
When the input source is analog coming
RGB
Move the pointer to
RGB, Video or Y, Pb/Cb,
Pr/Cr and press the
SELECT button.
from a computer through the Input 2 (5
BNC-type: Red, Green, Blue, H. Sync. and
V. Sync.) terminal, select RGB.
When video input signal is connected to the
Input 2 (VIDEO) terminal , select Video.
Video
When the input source is component
Y, Pb/Cb, Pr/Cr
coming from video equipment connected
to the Input 2 (Y, Pb/Cb, Pr/Cr) terminal,
select Y, Pb/Cb, Pr/Cr.
Input 3
Move a pointer to Input 3 and press the SELECT button.
When video input signal is connected to the
Input 3 (VIDEO) terminal, select Video.
Video
Source Select Menu
Move the pointer to
Video, Y, Pb/Cb, Pr/Cr
or S-Video and press
the SELECT button.
When the input source is component
Y, Pb/Cb, Pr/Cr
coming from video equipment connected
to the Input 3 (Y, Pb/Cb, Pr/Cr) terminal,
select Y, Pb/Cb, Pr/Cr.
When video input signal is connected to the
Input 3 (S-VIDEO) terminal, select S-Video.
S-Video
Input 4
When digital PC/AV source is connected to the Warp & Blending
board inserted into the Input 4 terminal, the following source
menu will be displayed.
When the input source is digital coming from a
computer through the Input 4 (DVI) terminal,
select RGB (PC Digital)
RGB (PC Digital)
When the input source compatible with HDCP
is coming from video equipment through the
Input 4 (DVI) terminal, select RGB (AV HDCP).
RGB (AV HDCP)
✔Note:
Warp & Blending board is initially installed into the Input 4 terminal slot. For details
on Warp & Blending feature, refer to the enclosed operation manual.
✔Note:
• Input 4 and Input 5 can not be selected when no interface
board is inserted into the respective slots. (p21)
• Input 5 terminal can only accept digital signals.
Input 5
• Adjusted values or selected settings in Input 4 and Input 5
return to factory default setting when the connected interface
boards are removed from those terminal slots.
A source menu appears corresponding to the board module
inserted into the Input 5 terminal.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
System
System
selects system of the connected computer and video source.
PC System Menu
PC System Selection
Auto
This projector automatically tunes to various types of computers
based on VGA, SVGA, XGA, SXGA, UXGA, or WXGA with its Multi-
scan system and Auto PC Adjustment. If Computer source is
selected in the Source Select Menu, this projector automatically
detects the signal format and tunes to project a proper image
without any additional setting. (Signal formats provided in this
projector is shown on page 72~73 )
System icon
Custom Mode
(1~50) set in the
PC Adjust Menu.
(p42, 43)
✔Note:
The projector may display one of the following messages.
User preset system manually adjusted in PC Adjust
menu. Adjustment data can be stored in Mode 1–50.
(p42~43)
Mode 1
The system being selected.
PC Systems provided in the projector. The projector
chooses a proper system and displays it.
SVGA 1
-----
There is no signal input from computer. Check the
connection of your computer and the projector. (See
" Troubleshooting" p70)
*SVGA 1 and Mode 1 are examples.
Selecting PC System Manually
When the projector has difficulty in recognizing the connected
signal conforming to PC Systems provided in this projector,
several systems are displayed. Select one from them manually.
When the image is not projected properly, manual adjustment is
required. (p42~43)
Press the MENU button to display On-Screen Menu. Spin
the menu icons with the Control pad and press the SELECT
button when the SYSTEM icon comes right in front.
1
Move the yellow frame pointer with the Control pad to a
proper system, and then press the SELECT button.
2
39
Download from Www.Somanuals.com. All Manuals Search And Download.
System
AV System Menu (Video or S-Video)
Video or S-Video Signal Selection
Auto
The projector automatically detects incoming video system, and
adjusts itself to optimize its performance.
When Video System is PAL-M or PAL-N, select system manually.
PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N
If the projector cannot reproduce proper video image, it is
necessary to select a specific broadcast signal format among PAL,
SECAM, NTSC, NTSC 4.43, PAL-M, and PAL-N.
Move the yellow
frame pointer to a
system and press
the SELECT button
to activate it.
✔Note:
When Auto is selected for the System menu, PAL-M and PAL-N cannot be selected.
AV System Menu (Component)
Component Signal Selection
Auto
The projector automatically detects incoming video signal, and
adjusts itself to optimize its performance.
COMPONENT VIDEO SIGNAL FORMAT
If the projector cannot reproduce proper video image, it is
necessary to select a specific component video signal format
among 480i, 575i, 480p, 575p, 720p, 1035i, 1080i/50 and 1080i/60.
Move the pointer to
a system and press
the SELECT button
to activate it.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Adjustment
selects Auto PC adj., Fine sync, Total dots, Current mode, Clamp, Display
area, Position, V -sync phase, Reset, and Mode.
PC Adjustment
PC Adjust Menu
Auto PC Adjust
Auto PC adj.
Press the MENU button to display On-Screen Menu. Spin
the menu icons with the Control pad and press the SELECT
button when the PC ADJ. icon comes right in front.
1
2
PC ADJ. icon
Move the yellow frame pointer to Auto PC adj. and then
press the SELECT button twice.
This Auto PC Adjustment can be also executed by pressing
the AUTO PC ADJ. button on the top control or the AUTO
PC button on the remote control unit. (p15, 31)
Move the yellow
frame pointer to the
Auto PC adj. and
press the SELECT
button.
To store adjustment parameters
Adjustment parameters from Auto PC Adjustment can be
memorized in this projector. Once parameters are memorized, the
setting can be done just by selecting Mode in the System menu
(p39). See Store on page 43.
✔Note:
• Fine sync, Total dots and Picture Position of some computers can not be fully
adjusted with this Auto PC Adjustment function. When the image is not provided
properly with this operation, manual adjustments are required. (p42, 43)
• Auto PC Adjustment function cannot be operated in Digital Signal input on DVI
terminal and “480i”, “575i”, “480p”, “575p”, “720p (HDTV)”, “1035i (HDTV)”,
“1080i/50 (HDTV)” or “1080i/60 (HDTV)” is selected on the System menu (p40).
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Adjustment
Manual PC Adjust
PC Adjust Menu
Some computers employ special signal formats which may not be
tuned by Multi-scan system of this projector. Manual PC
Adjustment enables you to precisely adjust several parameters to
match those signal formats. The projector has 50 independent
memory areas to memorize those parameters adjusted manually.
It allows you to recall the setting for a specific computer easily.
Press the MENU button to display On-Screen Menu. Spin
the menu icons with the Control pad and press the SELECT
button when the PC ADJ. icon comes right in front.
1
Move the yellow
frame pointer to an
item and press the
SELECT button.
Move the yellow frame pointer with the Control pad to an
item which you want to select.
2
Press the SELECT button to display an adjustment dialog
box. Adjust value with the Control pad.
3
Fine sync
Eliminates flicker from the image displayed. Adjust value with
the Control pad. (From 0 to 31)
Adjust value with
the Control pad.
Total dots
Adjusts the number of total dots in one horizontal period.
Adjust number to match your PC image with the Control pad.
Current mode
Press the SELECT button to show H-Freq. and V-Freq. of the
connected computer.
Clamp
Adjusts clamp level (Phase and Width). When the image has
dark bars, try this adjustment.
Current mode
Display area
Press the SELECT button at
the Current mode to show
the information of the
Adjusts the resolution at the Display area dialog box.
Horizontal
connected computer.
Adjusts the horizontal area displayed by this projector.
Decrease or increase value with the Control pad.
Vertical
Adjusts the vertical area displayed by this projector.
Decrease or increase value with the Control pad.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Adjustment
Position
Adjusts picture position.
V-sync phase
Adjust this item when the projected image is affected by the
noise from the external equipment. (From 0 to 15)
Press the SELECT button
at the Display area and the
Display area dialog box
appears.
✔Note:
V-sync phase is not displayed as the item is initially checked off on My menu in the
Setting menu. Change the My menu setting in the Setting menu (p51) when
necessary to adjust V-sync. phase.
Reset
Resets all adjustments to their previous levels.
Mode
To store the adjustment data or clear the stored data, move the
yellow frame pointer to Mode and then press the SELECT
button.
To store adjustment data
Store
To store the adjustment data, select Store and press the
SELECT button to display Mode dialog box. Move the
yellow frame pointer to any of Mode 1 to 50 in which you
want to store and then press the SELECT button.
Free
To clear the adjustment data previously set, select Free and
press the SELECT button to display Mode dialog box. Move
the yellow frame pointer to any of Mode 1 to 50 in which
you want to clear and then press the SELECT button.
Vacant Mode
shows the selected input,
source and system, and values
of “Fine sync,” “Total dots,”
“Clamp,” “Display area,” and
“Position.”
Quit
Exits the PC Adjust Menu.
To clear adjustment data
✔Note:
Fine sync. and Display area cannot be selected when “480i”, “575i”, “480p”,
“575p”, “720p”, “1035i”, “1080i/50” or “1080i/60” is selected in the System
menu (p40).
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Adjustment
selects image level from Standard, Cinema, Real, and Image 1~10.
Image
Press the MENU button to display On-Screen Menu. Spin
the menu icons with the Control pad and press the SELECT
button when the IMAGE icon comes right in front.
Image Menu (PC)
1
Move the yellow frame pointer with the Control pad to an
image level which you want to select and then press the
SELECT button.
2
IMAGE icon
Move the yellow
frame pointer to
an image level
you want to select
and then press
the SELECT
For PC Input
button.
Standard
Normal picture level preset on this projector for PC mode.
Real
Indicates the other
items exists below.
Picture level with improved halftone for graphics.
IMAGE 1~10
User preset picture adjustment in IMAGE ADJ. menu (p45~47).
Image Menu (AV)
For AV Input
Standard
Normal picture level preset on this projector for AV mode.
Cinema
Picture level adjusted for picture with fine tone.
IMAGE 1~10
User preset picture adjustment in IMAGE ADJ. menu (p45~ 47).
✔Note:
Image 1~10 are common for PC and AV sources, which means 10 memory areas are
prepared for PC and AV sources totally.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Adjustment
adjusts Contrast, Brightness, Color, Tint, Color management, Auto picture
control, Color temp., Red, Green, Blue, Sharpness, Gamma, Noise reduction,
Progressive, Film, and selects Reset and Store.
Image Adjust
Press the MENU button to display On-Screen Menu. Spin
the menu icons with the Control pad and press the SELECT
button when the IMAGE ADJ. icon comes right in front.
Image Adjust Menu
1
Move the yellow frame pointer with the Control pad to an
item which you want to adjust.
2
3
IMAGE ADJ. icon
Press the SELECT button to display an adjustment dialog
box. Adjust value with the Control pad.
Pointer
(yellow frame)
Softly tap the Control
pad or grind your
finger on the Control
pad to move the
pointer.
Contrast
Decrease or increase contrast with the Control pad.
(From 0 to 63.)
Brightness
Indicates the other
items exists below.
Adjust image darker or brighter with the Control pad.
(From 0 to 63.)
Color
Lighten or deeper color with the Control pad.
(From 0 to 63.)
Tint
Adjust with the Control pad to obtain proper color.
(From 0 to 63.)
Color management
The Color management function enables you to adjust color level,
phase and gamma of the selected spot of the projected image and
exchange the original color with the adjusted one.
Item data
Adjust value with the
Control pad.
The projector can store up to eight color management data.
Color selection
Press the SELECT button when Color management is
highlighted and then Color management pointer will appear.
Move the pointer to a spot which you want to adjust the color
of with the Control pad, and press the SELECT button. The
image being projected freezes and Color Selection window will
appear.
Color selection
Color management pointer
Move the pointer to a spot which you
want to adjust the color of and then
press the SELECT button. Color
Selection window will appear as
below.
X-axis of COLOR pallet shows Phase and Y-axis, Level.
Select a level and phase which you prefer with the Control pad
and press the SELECT button to move the pointer to GAMMA.
Pointer
(red frame)
Select a position of GAMMA which you prefer with the Control
pad and press the SELECT button.
While adjusting COLOR and GAMMA, the projected image
color will change accordingly.
✔Note:
• Color and Tint cannot be displayed when PC input source is selected.
• Tint cannot be adjusted when the video system is PAL, SECAM, PAL-M or PAL-N.
(p40)
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Adjustment
Move the pointer to one of the followings with the Control pad
and press the SELECT button.
Color management list
Move the pointer to
the selected color
............displays Color Management List window to store
the adjustment data.
LIST
and
press
the
..returns to the previous image with the Color
management pointer.
SELECT button.
The confirmation
dialog box appears.
COLOR.M
.........displays a confirmation dialog box. Select "Yes" to
return to the menu display.
MENU
Color management list
After selecting LIST on the Color selection window, Color
Management List will appear. Move the pointer to one of the
followings with the Control pad and press the SELECT button.
Select [Yes] to
return to the
menu display.
Clear the check mark with the
SELECT button not to apply
the adjusted color to the
projected image.
......deletes all the data on the list.
ALL DEL
MENU
.........displays a confirmation dialog box. Select "Yes" to
return to the menu display.
..returns to the previous image with the Color
management pointer.
COLOR M.
Press the CANCEL button to exit the Color management mode.
Auto picture control
With this function enabled, the projected image will be easier to
see by emphasizing black of the picture. Select one from the
following settings:
Off ······disabled
L1 ······ emphasizes black of the picture.
L2 ·······emphasizes black of the picture greater than L1.
Color temp.
Select a level among XLow, Low, Mid and High with the Control
pad and the SELECT button.
Red
The setting selected.
Lighten or deepen red tone of the picture with the Control pad.
(From 0 to 63.)
Green
Lighten or deepen green tone of the picture with the Control pad.
(From 0 to 63.)
Blue
Lighten or deepen blue tone of the picture with the Control pad.
(From 0 to 63.)
✔Note:
If either value of Red, Green, and Blue is adjusted, "Adj." will be selected in Color temp.
automatically.
Sharpness
Soften or sharpen the image with the Control pad. (From 0 to 15.)
The setting selected.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Adjustment
Gamma
Adjust with the Control pad to obtain better balance of contrast.
(From 0 to 15.)
Noise reduction
Select one of the followings to reduce noise of the image.
Off . . . .disabled
L1 . . . . .Select “L1” for an active picture.
L2 . . . . .Select “L2” for a still picture.
Progressive
With this function On, interlaced video signal is displayed in a
progressive picture.
Film
This function is effective on 2:3 or 2:2 pulldown video sources.
With this function On, the projector reproduces pictures faithful to
the original film quality.
Store
To store the adjustment data, move an yellow frame pointer to
Store and press the SELECT button. Image Level Menu will
appear. Move the yellow frame pointer to one of Image 1~10 and
then press the SELECT button.
Store
Reset
Reset all adjustments to their previous figures.
Quit
Exits Image Adjust menu.
Image Level Menu
Move the yellow frame pointer to an
image and then press the SELECT
button. The confirmation box
appears.
Select [Yes] to store the image
adjusted.
✔Note:
• Progressive, Film, and Noise reduction cannot be displayed when selecting PC input
source.
• Progressive cannot be selected when 480p, 575p, and 720p is selected in the
System menu. (p40)
• Film can only be activated when selecting PAL, NTSC, 480i or 575i for Video
System and "On" for Progressive.
• 2:3 Pulldown or Telecine transfer is the process of changing images from film mode
to video mode. While film runs at 24 frames per second (fps), NTSC television
signals (or video) have a run rate of 30fps so the 24 fps film needs to be speeded
up to 30fps and transferred using a proper field pattern to get the best film-like
images. 2:2 Pulldown uses the same process of changing images as 2:3 pulldown,
but the difference is that 24 fps film is speeded up for PAL television signal (or
video) having 25 fps.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Screen Setting
selects the screen size from Normal, Wide, True and Full screen;
customizes it by Scale, H&V, Position, Common and Reset; adjusts it by
Digital zoom +/–, Keystone and sets Ceiling and Rear.
Screen Setting
Press the MENU button to display On-Screen Menu. Spin
the menu icons with the Control pad and press the SELECT
button when the SCREEN SETTING icon comes right in
front.
Screen Setting Menu
1
2
Screen Setting
icon
Move the yellow frame pointer with the Control pad to an
item which you want to select.
Screen
Normal
Provides image to fit screen size.
Wide
Screen (Custom)
Provides image to fit wide video aspect ratio (16 : 9) by
expanding image width uniformly. This function can be used
for providing a squeezed video signal at 16 : 9.
Aspect Setting Menu
Move the pointer to an item to
set and adjust value with the
Control pad.
True
Provides image in its original size. When the original image size
is larger than the screen size, this projector enters panning
mode automatically. While "True" is displayed on screen, pan
the image with the Control pad. Digital zoom + and – mode can
be switched by pressing the SELECT button.
Pointer
Full screen
Item data
Provides image to fit the horizontal size of the screen size.
When the input signal is SXGA (5:4), the image is fully displayed
at 4:3 aspect ratio.
Adjust value with
the Control pad.
Screen (Custom: H&V)
Custom (Aspect)
Adjusts aspect (scale and position) of the screen. Press the
SELECT button at "Custom". "Custom" will be displayed on the
top left of the screen for 4 seconds and then return to the
previous menu display. Press the SELECT button again with
the pointer staying on Custom to display Aspect setting menu.
Adjust each value of Scale and Position.
Checkmark
Scale . . . . .adjusts horizontal and vertical scale of the screen.
(From –32 to +32)
Screen (Custom: Common)
H&V . . . . . .changes Vertical value subject to Horizontal
value; when a checkmark is put on H&V, Scale V
cannot be adjusted.
Position . . .adjusts horizontal and vertical position of the
screen. (From –15 to +15)
Common . .applies the current Aspect setting to all the
Inputs.
Reset . . . . .resets all adjusted values to zero.
Quit . . . . . .exits the Aspect setting menu.
Pointer
Move the pointer to "Common" and
press the SELECT button. The
confirmation box appears. Select [Yes]
to activate it.
✔Note:
The adjusted aspect can basically be memorized for each input even if the projector
is turned off.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Screen Setting
D. Zoom
D. Zoom
D. Zoom +
Press the SELECT button at the D. Zoom +. The message “D.
Zoom +” is displayed. Press the SELECT button to expand the
image size. And use the Control pad to pan the image. The
Panning function can work only when the image is larger than
the screen size.
D. Zoom –
Press the SELECT button at the D. Zoom –. The message “D.
Zoom –” is displayed. Press the SELECT button to compress
the image size.
✔Note:
To exit the D. Zoom +/– mode, try the followings:
• To return to the normal screen, change Input, or change the screen size.
• To exit the panning mode, press any button except the D. ZOOM button, the
SELECT button, and the CH and ID buttons.
Keystone
Keystone
This function corrects distortion of a projected image. Press the
SELECT button at Keystone twice and The keystone dialog box
appears. Adjust keystone with the Control pad.
Press the SELECT button at Keystone and select either Store or
Reset with the Control pad, and then press the SELECT button to
fix the selection.
Store . . . .stores the keystone adjustment even if the AC
power cord is disconnected.
Reset . . . . .resets the keystone adjustment when the AC power
cord is disconnected.
Ceiling
Ceiling
When this function is “On,” the picture is top/bottom and left/right
reversed. This function is used to project the image from a ceiling
mounting the projector.
Rear
When this function is “On,” the picture is left/right reversed. This
function is used to project the image to a rear projection screen.
Rear
✔Note:
• The True and D. Zoom +/– cannot be selected when projecting AV sources or
selecting “480i”, “575i”, “480p”, or “575p” in the System menu (p39~40).
• This projector cannot display any resolution higher than 1600 X 1200. If your
computer’s screen resolution is higher than 1600 X 1200, reset the resolution to
the lower before connecting the source to the projector.
• The image data in other than XGA (1024 x 768 for PLC-XF60) or SXGA (1400 x
1050 for PLC-EF60) is modified to fit the screen size in initial mode.
• The panning function may not operate properly if the computer system prepared in
the PC Adjust Menu is used.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Sound
Sound
adjusts Volume, Treble, Bass, or mutes sound.
Press the MENU button to display On-Screen Menu. Spin
the menu icons with the Control pad and press the SELECT
button when the SOUND icon comes right in front.
Sound Menu
1
Sound icon
Pointer
(yellow frame)
Move the yellow frame pointer with the Control pad to an
item which you want to adjust.
Softly tap the Control
pad or grind your
finger on the Control
pad to move the
pointer.
2
3
Press the SELECT button to display an adjustment dialog
box. Adjust value with the Control pad.
Item data
Adjust value with the
Control pad.
Volume
Adjust Volume with the Control pad.
Treble
Adjust Treble sound with the Control pad.
Bass
Adjust Bass sound with the Control pad.
Mute
Select On to cut off sound, and select Off to restore sound.
Quit
Exits Sound menu.
Exits the Sound Menu.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
changes various settings: Language, Menu, Logo, Background, Lamp,
Remote control, Display, Input search, Power management, On start, Analog
out, Lens memory, Shutter, Security, and Factory default.
Setting
Press the MENU button to display On-Screen Menu. Spin
the menu icons with the Control pad and press the SELECT
button when the SETTING icon comes right in front.
Setting Menu (Language)
1
2
Setting icon
Move the yellow frame pointer with the Control pad to an
item which you want to set and then press the SELECT
button. The Setting dialog box appears.
Language Menu
Language
The language used in the On-Screen Menu is available in English,
German, French, Italian, Spanish, Portuguese, Dutch, Swedish,
Russian, Chinese, Korean, or Japanese.
Menu Position
Menu
This feature allows you to change the On-Screen Menu setting.
Position
When Position is selected, arrows appear in upward, downward,
right and left directions on the screen. Move the menu position
with the Control pad and fix it by pressing the SELECT button.
My menu
This feature enables you to customize the On-Screen menu
display. Put checkmarks on items of each menu that you want
to display.
Simple menu
On . . . . . . .When adjusting value in the Image adjust menu, the
value adjustment bar is displayed on the bottom left
of the screen.
My Menu
Off . . . . . . .Default setting.
Pointer
✔Note:
• Input and Menu items cannot be hid with the My menu setting.
• When selecting Default on My menu setting, all items of the On-Screen Menu will
be displayed.
Checkmark
Move the pointer to an item to
be displayed and put
checkmark on the item by
pressing the SELECT button.
a
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Logo Select
Logo
Logo settings can be altered as follows:
Logo select
This function decides what to be displayed on the starting-up
display as follows:
Default . . . .the factory-set logo
My logo . . .the image you captured
Off . . . . . . .count-down only
Capture
This function enables you to capture the image being projected
and use it for a starting-up display or interval of presentations.
After capturing the projected image, go to the Logo function and
set it to “My logo”. Then the captured image can be displayed
when turning on the projector next time. (p28)
Capture
To capture the image, select [Yes]. To cancel the Capture
function, select [No].
Select [Yes] to
capture the
p r o j e c t e d
image.
✔Note:
• Before capturing an image, select Standard in the Image Menu to capture a proper
image. (See page 44.)
• Certain signals may not be captured properly.
• When capturing the image that has been adjusted by the Keystone function, the
adjustment data is automatically reset and the projector captures an image without
keystone correction.
• Once you exit the Logo menu after setting Logo lock to "On", you are required to
enter the PIN code every attempting to change the Logo setting.
Select [Yes] to
stop capturing.
Logo Lock Setting
Lock
This function prevents an unauthorized person from changing the
Logo setting.
Off . . . . .the Logo setting can be changed freely from the
Logo menu.
On . . . . . .the Logo setting cannot be changed without PIN
code.
If you want to change the Logo Lock setting, enter a PIN code
along the following steps. The initial PIN code for Logo Lock
setting is set "4321" at the factory.
Enter a Logo PIN code
Enter a Logo PIN code
Select a number with the Control pad and fix the number with
the SELECT button. The number will change to "✳". If you
fixed a wrong number, move the pointer to "C" with the Control
pad, then enter the correct number again.
The input numbers
change to “✳” for
security.
Repeat this step to complete entering a four-digit number.
When the four-digit number is fixed, move the pointer to "Ent".
Press the SELECT button so that you can change the Logo
Lock setting.
If you entered a wrong Logo PIN code, "Logo PIN code" and the
number (✳✳✳✳) will turn red and disappear. Enter a correct
Logo PIN code all over again.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
PIN Code Change
PIN Code change Dialog Box
Logo PIN code can be changed to your desired four-digit number.
Select "PIN code change" with the Control pad and press the
SELECT button. Set a new Logo PIN code.
Select PIN code change and
press the SELECT button.
The PIN code input dialog box
will appear.
Be sure to note the new Logo PIN code and keep it at hand. If
you lost the number, you could no longer change the Logo PIN
code setting. For details on PIN code setting, refer to relevant
instructions of the PJ Lock function on page 57.
Background
3 background settings are available in this projector. Select one of
the followings when no input source is connected to the projector
or no input signal is coming from the connected equipment:
Blue . . . . . .blue colored background
Pointer
My logo . . .the image you captured
Black . . . . .black colored background
Lamp Control
Lamp
Control
This feature allows you to change brightness of the screen.
. .normal brightness
Normal
brightness according with the input signal
Auto . . . .
. . . .lower brightness reduces the lamp power
consumption and extends the lamp life.
Eco
✔Note:
When using 100 W (optional) lamps, the Lamp control setting cannot be altered.
Mode
Lamp Mode
This projector is equipped with two lamps. Mode setting allows
you to switch using 1 lamp or 2 lamps.
2-lamp . . . .lights both of the lamps inside the projector.
1-lamp . . .lights a lamp only. Auto, Lamp1, or Lamp2 can be
altered.
✔Note:
When selecting Auto in 1-Lamp
mode, the projector automatically
selects either lamp of which the
total Lamp time is shorter and
lights it up.
• When neither of the two lamps is lighted, the projector will shutdown automatically.
• When either of the two lamps does not light up, the LAMP 1/2 REPLACE indicator
is blinking red and the projector will light the other automatically.
Remote control
Remote control
Four remote control channels and eight remote control ID are
prepared for the projector to prevent radio frequency interference
from the other equipment and mutual interference between
projectors when using them at the same time.
Pointer
For example, operating the projector in “CH-2 and ID-7,” both the
projector and the remote control must be switched to “CH-2 and
ID-7.”
The setting
selected.
To change CH and ID for the projector;
Select a remote control CH and ID in this Setting menu.
To change CH and ID for the remote control;
While holding down the CH or ID button, press the SELECT
button. The remote control CH or ID switches sequentially for
one pressing the SELECT button. Changing CH and ID should be
done separately. (See page 16 and 17 for details.)
When pressing the SELECT button at Remote control,
the remote control CH and ID menu appears. Select CH
and ID respectively.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Display
This function decides whether to display On-Screen Displays.
On . . . . .shows all the On-Screen Displays.
Off . . . . .sets On-Screen Displays disappeared except;
●
●
On-Screen Menu
“Power off?” message
●
●
●
●
P-TIMER
“No signal” message
“Please wait...” message
“Searching...” message
Input search
With this function On, the projector automatically starts input
signal search from Input 1 to Input 5 when turning on the
projector. This automatic search stops at the Input where the
projector detects any input signal connected.
✔Note:
When the last selected input source in the Input menu differs from the detected input
source, the projector may not display the image properly.
Power management
Power management
For reducing power consumption as well as maintaining the lamp
life, the Power Management function starts the count down when
the input signal is interrupted and no button is pressed for 30
seconds or more.
Time left until Lamp off
If the input signal is interrupted and no button is pressed for 30
seconds or more, the timer display with the message "No signal"
appears on the screen. The count-down of the set time will get
started. The count-down time can be set between 1 and 60
minutes.
Press the SELECT button
at Power management and
this box appears. Choose
"Off" to disable the timer
When the count-down time has been elapsed, the lamp will be
turned off to cool itself down. The POWER indicator is lighting red
during this cooling-off period. The next operation depends on the
setting as follows :
setting,
"Ready"
or
"Shutdown" to enable the
timer setting.
Ready . . . . . .When the lamp has been fully cooled down, the
READY indicator changes to green blinking. In
this condition, the projection lamp will be turned
on if the input signal is reconnected or any
button on the top control or remote control unit
is pressed.
Shut down . . .When the lamp has been fully cooled down, the
power will be turned off.
Timer Setting
Off . . . . . . . . .The Power Management function is canceled.
Move the pointer to the
timer and set time with the
Control pad and press the
SELECT button. The timer
window disappears and
then choose "Ready" or
"Shutdown" to enable the
timer setting.
On start
When this function is “On,” the projector is automatically turned
on just by connecting the AC power cord to a wall outlet.
✔Note:
Be sure to turn the projector off properly (see “Turning Off the Projector” on page
29). If the projector is turned off in the wrong steps, the On start function does not
operate properly.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Analog out
The ANALOG OUT terminal is for output of the analog signal
coming from the ANALOG IN terminal in the Input 1 terminals.
(See page12.)
Select "On" to enable the signal output through the ANALOG OUT
terminal always except in the stand-by mode or "Off" to disable the
signal output.
Lens memory
Analog out is not available when selecting the other Inputs except
Input 1. Select Input 1 so that Analog out will be available. (p31,
37)
Press the SELECT button at
Lens memory and choose an
Input for which you want to
store the lens shift, zoom and
focus adjustment and then
select "Memory" for the input.
Lens memory
Lens memory feature enables you to store the lens shift, zoom
and focus adjustment for each Input. When selecting Lens
memory, Input 1~5 will be displayed. Move the pointer to an
Input and press the SELECT button. Choose one of the following
settings for the Input.
Off . . . . . . . . applies the lens shift, zoom and focus adjusted
last.
Memory . . . . stores the lens shift, zoom and focus currently
adjusted for each input. When switching to the
input with "Memory" selected, the lens moves to
the stored position.
Select [Yes]
to activate
the setting.
Shutter level
✔Note:
• Lens memory is available only in the lens having memory functions of itself. Contact
to the sales dealer or the service station for available lens.
• 100% accurate lens memory is not guranteed. If an accurate lens position, zoom
and focus cannot be obtained with Lens memory function, adjust them respectively
in each case.
Shutter
Shutter function is available to block out light to the screen, so that
the screen can be used for the other presenters. Moreover, this
function enhances the effectiveness of contrast by 80% opening
up the shutter inside the projector.
Each setting for the Shutter function can be altered as follows:
Level
Sets up shutter level when releasing the mechanical shutter.
Shutter protection
Normal . . . . . . . . . .0% light blocking
High contrast . . . . .20% light blocking
Protection
Prohibits the shutter operation from the remote control and the
projector's top control.
Remote control . . Selecting "On" prohibits the shutter operation
from the remote control.
Projector . . . . . . . . Selecting "On" prohibits the shutter operation
from the top control.
When pressing the SELECT button at Shutter, the
Shutter setting menu appears. Select Protection and
then a desired setting for Remote control and Projector.
It is possible to prohibit the shutter operation from both of the
remote control and the top control.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Shutter Management
Shutter Management
The Shutter Management function turns off the projection lamp
when the projector is left with the shutter released and the set
time has passed away. The count-down time can be set
between 5 and 180 minutes.
When the count-down time has elapsed, the shutter will be
opened up automatically and the lamp will be turned off to cool
itself down. The SHUTTER indicator is blinking blue during this
cooling-off period. When the lamp has been fully cooled down,
the READY indicator turns green lighting and the SHUTTER
indicator keeps blinking. Should the POWER button be pressed
in this condition, the projection lamp will be turned on and the
SHUTTER indicator turns off.
✔Note:
While the Shutter is released, timer setting of the Power management is invalid.
Select Management and set the timer between 5 and
180 minutes.
Security
Key lock
This function locks operation from the top control and remote
control. It is useful to prevent the projector from being operated
by an unauthorized person.
Key lock
Projector
locks operation from the top control. To
unlock, use the remote control.
. . . . . . .
locks operation from the remote control. To
unlock, use the top control.
Remote control . .
Off . . . . . . . . . . . .does not lock any operation. To release lock,
select this.
If the top control accidentally becomes locked and you do not
have the remote control nearby, disconnect the AC power cord
from the AC outlet, and then with pressing the SELECT button,
reinsert the AC power cord. This will cancel the top control lock.
USB lock
This function prevents the projector from being operated by an
unauthorized person with the optional USB key and provides the
following settings for security options.
The setting selected.
. . . . . .key lock setting (On1, On2, and Off)
Setting
. .registers 2nd USB key into the projector. (First
key can be registered by just being connected to
the projector in turning on.)
USB lock
Registration
. . . . . . .deletes the registered USB keys.
Delete
To set the USB lock, the optional USB key is required. Refer to
p75 for the optional USB key and contact the sales dealer for
purchasing. Refer to the owner's manual enclosed with the USB
key for detail operation of the USB lock.
The setting selected.
✔Note:
• USB lock cannot be selected when the optional USB key is not connected to the
projector. (p13)
• When either of USB lock or PJ lock is set, the other cannot be selected.
• USB key function can be used only with our specified optional USB key. We do not
guarantee operation with the other USB keys commarcially supplied.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
PJ lock
PJ lock
This function prevents the projector from being operated by an
unauthorized person and provides the following settings for
security options.
. . . . . .requires to enter the PIN code every time turning on
the projector.
On1
On2
. . . .requires to enter the PIN code to operate the
projector once the power cord is disconnected; as
long as the AC power cord is connected, the
projector can be operated without the PIN code.
. . . . .the projector is unlocked with the PIN code. To
release PJ lock, select this setting.
When the projector is
locked with the PIN
code, the PJ lock mark
appears at top left of
the Main menu.
Off
Whenever to change the PIN code (the four-digit number), you
are required to enter the PIN code. "1234" is set as the initial PIN
code at the factory.
Enter a PIN code
Enter a PJ PIN code
Select a number with using the Control pad and fix the number
with the SELECT button. The number will change to "✳". If you
fixed a wrong number, move the pointer to "C" once with the
Control pad to clear the number. Enter the correct number
again.
Repeat this step to complete entering a four-digit number.
When the four-digit number is fixed, move to "Ent". Press the
SELECT button so that you can change the following PIN code
lock settings.
The input numbers
change to “✳” for
security.
If you entered a wrong PIN code, the number (✳✳✳✳) will turn
red and disappear. Enter a correct PIN code all over again.
To Change the PJ PIN Code setting
Select Off, On1, or On2 with the Control pad and then press
the SELECT button.
Pointer
Change the PJ Lock setting
To Change PJ PIN Code
The PIN code can be changed to your desired four-digit
number.
Select "PJ PIN code change" with the Control pad, and press
the SELECT button. The PIN code input dialog box will appear.
Enter a current PIN code, and then a new PIN code as follows:
Select a desired
setting with the
Control pad and
press the SELECT
button.
Select a number with the Control pad and fix the number with
the SELECT button. Repeat it to complete entering a four-digit
number. When the four-digit number is fixed, move the pointer
to "Ent". Then press the SELECT button.
Change the PIN code
Select PJ PIN code change and press
the SELECT button. The PIN code input
dialog box will appear.
CAUTION:
WHEN YOU HAVE CHANGED PIN CODE, WRITE DOWN THE
NEW PIN CODE IN COLUMN OF THE PIN CODE NO. MEMO
ON PAGE 81, AND KEEP IT SECURELY. SHOULD THE PIN
CODE BE LOST OR FORGOTTEN, THE PROJECTOR CAN NO
LONGER BE OPERATED.
The setting selected.
Pointer
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Factory default
Factory default
This function returns all setting values to the factory default
settings except for those including: User logo, PJ PIN code, Logo
PIN code, Security setting, Lamp time, Filter time and PJ time.
Quit
Exits the Setting menu.
Select Factory default and
this box appears. Select
[Yes], and the next box
appears.
Select [Yes]
to activate it.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Special
customizes control functions: Lamp, Fan control, Filter, Auto PC adj., Test pattern, RS-
232C, and USB memory and displays Warning log.
Special
Press the MENU button to display On-Screen Menu. Spin
the menu icons with the Control pad and press the SELECT
button when the SPECIAL icon comes right in front.
Special Menu (Lamp)
1
2
Move the yellow frame pointer with the Control pad to an
item which you want to select and then press the SELECT
button. The corresponding dialog box for the item appears.
Special icon
Lamp
Move the pointer to Reset
and then press the SELECT
This feature displays total time of the lamps being used. Select
Lamp 1 or Lamp 2 to show each lamp wattage and time.
button.
The message
“Lamp time reset?” is
displayed. Select [Yes] and
the confirmation box
appears.
To reset the Lamp time, move the pointer to "Reset" and then
press the SELECT button. The message "Lamp time reset?" is
displayed. Move the pointer to [Yes] and then press the SELECT
button.
Select [Yes]
to activate
it.
✔Note:
Be sure to reset the Lamp time only after replacing the lamp.
Fan control
Fan control
This function provides you the following alternatives for the
cooling fans operation of the projector and the Option box (Smoke
Resist Box ) separately provided. See page 75 for the Option box.
Select Fan control and this
box appears. Select one of
these settings with the
Control pad and press the
SELECT button to enable it.
Normal . . .normal operation
Max . . . . . .faster operation than "Normal".
Select "Normal" for usual operation and "Max" to enhance the
cooling effect.
✔Note:
Setting of the cooling fans of the projector and the option box cannot be changed
independently.
The setting selected.
Filter
This feature displays total time of the filter on the projector and
the Option box (Smoke Resist Box) being used.
Filter
To reset the Filter time, move the pointer to "Reset" and then
press the SELECT button. A confirmation box appears. Move the
pointer to [Yes] and then press the SELECT button.
✔Note:
Move the pointer to Reset and
then press the SELECT button
and the confirmation box
appears.
Option box cannot be selected when it is not mounted on the projector. For the
information of the Smoke Resist Box, refer to Optional Parts on p75 and contact the
sales dealer or the service station.
Select [Yes] to
activate it.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Special
Test pattern
Auto PC adj.
Select "On" to enable the Auto PC adjust function and "Off" to
disable it. Refer to page 31 and 41 for Auto PC adjust function.
Select Test pattern and
then the Test pattern
selection box is displayed.
Choose one of these
patterns with the Control
pad and press the SELECT
button to display the
selected pattern on screen.
Test pattern
Various test patterns are prepared in this projector allowing users
to test the projection. Select one from the following twenty kinds
of patterns: Cross 1 (W), Cross 2 (R), Cross 3 (G), Cross 4 (B),
Cross 5 (M), Cross 6 (C), Cross 7 (Y), Gradation 1~4, Color, and
Flat 1~8.
To cancel the Test pattern, press the CANCEL button on the top
control or the remote control.
RS-232C
This feature allows users to set serial communication
configuration (baud rate and the projector ID) when connecting
several projectors via the RS-232C terminal of the projector. (p13,
80)
Indicates the other items
exist below.
Baud rate . . . . .9600 / 19200
Projector ID . . .001 ~ 999 ✽
Default . . . . .returns Baud rate and Projector ID to factory
default setting
RS-232C
(Baudrate: 19200, Projector ID: 001)
USB memory
This feature allows users to store PC mode and Image adjustment
data on the optional USB key connected to the projector and recall
it from the USB key. PC mode data and Image adjustment data
can be stored separately on respective 10 memory areas of the
USB key. (PC mode data: mode 1–50 x 10, Image adjustment
data: Image 1-10 x 10) (p43, 47)
Save . . . . . .stores the adjustment data on the USB key
connected to the projector.
Load . . . . . . . . .recalls the stored data.
Delete . . . . . . .deletes the stored data.
The item selected.
USB memory
To use the USB memory function, the optional USB key
(separately provided) is required. Refer to p75 for the USB key
information and contact the sales dealer or service station for
purchasing. Refer to the owner's manual enclosed with the USB
key for further information on USB memory function.
Move the pointer to one of
these and then press the
SELECT button and USB
Memory Menu appears .
✔Note:
• USB memory function cannot be operated without our specified optional USB key.
See page 75 for the optional parts.
• USB memory cannot be displayed without the optional USB key connected to the
projector. (p13)
To be continued to the next page.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Special
USB Memory Menu
Warning log
Move the yellow frame
pointer to a USB memory
to store the data and then
press the SELECT button.
The confirmation box
appears.
Warning log shows the information of the past warning history of
the projector. Up to 50 logs can be displayed. Log contents are
as follows:
Lamp-1 failure
Lamp-2 failure
Lamp-1 timeover
Lamp-2 timeover
Power failure
Select [Yes] to
activate it.
Inside temp. A error
Inside temp. B error
Inside temp. C error
External temp. error
Power off (Power management)
Power off (Shutter management)
PJ filter timeover
Warning log
Option box filter timeover
Option box error
Quit
Exits Warning log menu.
Exits the Warning log menu.
displays current setting information: Input, System, Signal, Screen, Language, Lamp
mode, Lamp status, Power management, Shutter management, Smoke resist,
Option filter time, Security, and Remote control.
Information
Press the MENU button to display On-Screen Menu. Spin
the menu icons with the Control pad and press the SELECT
button when the INFORMATION icon comes right in front.
Information
1
2
The Information window appears. The information window
can be displayed by pressing the INFO button on the top
control and the remote control.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Cleaning
Warning Temp Indicator
The WARNING TEMP indicator shows the state of the function which protects the projector. Check the state of the
WARNING TEMP indicator and the READY indicator to take proper maintenance.
The projector is shut down and WARNING TEMP indicator is
blinking red.
TOP CONTROL
The WARNING TEMP indicator slowly blinks red to let you know
the internal temperature of the projector exceeds the normal level.
If the temperature goes up further, the WARNING TEMP indicator
turns fast blinking and then the projector will be turned off
automatically. Then, the READY indicator will go out, but the
WARNING TEMP
blinking red
WARNING TEMP indicator keeps blinking red. When the
temperature inside the projector returns to normal, the READY
indicator lights green and then the projector can be turned on. If
the WARNING TEMP indicator still keeps blinking after the
projector is turned on, check the followings;
✔Note:
Even after the temperature inside the projector returns to normal, the WARNING
TEMP indicator continues to blink and does not go out until the projector is turned on
again.
Then check the matters below:
– Did you provide appropriate space for the projector to be
ventilated? Check the installing condition to see if ventilation
slots are not blocked.
– Is the projector not installed near the ventilation duct of air-
conditioning equipment which may be hot? Install the
projector away from the ventilation duct of air-conditioning
equipment.
– Are the air filter clean? Check the air filter periodically. (p63)
If the WARNING TEMP indicator remains blinking after performing
above checks, the cooling fans or the internal circuits may be
malfunctioned. Contact the service station for check and repair.
All indicators except the LAMP indicator are blinking.
TOP CONTROL
When the projector detects an abnormal condition, it is
automatically shut down to protect the inside and all the Indicators
except the LAMP indicator start blinking. In this case, disconnect
the AC power cord and reconnect it, and then turn the projector on
once again for check. If the projector cannot be turned on,
disconnect the AC power cord and contact service station for
check and repair.
LAMP 1 REPLACE, WARNING
TEMP, WARNING FILTER, READY,
SHUTTER , and LAMP 2 REPLACE
blinking altogether.
LAMP
lighting red
CAUTION
DO NOT LEAVE THE PROJECTOR WITH THE AC
POWER CORD CONNECTED UNDER THE ABNORMAL
CONDITION. IT MAY RESULT IN FIRE OR ELECTRIC
SHOCK.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Cleaning
Air Filter Replacement
Air filters prevent dust from accumulating on the surface of the optical elements inside the projector. Should the air filters
become clogged with dust particles, it will reduce cooling fans’ effectiveness and may result in internal heat build up and
adversely affect the life of the projector. Proper maintenance should be taken.
WARNING FILTER Indicator
TOP CONTROL
This projector can monitor the filter condition. When the filter is
clogged with dust and the performance is degraded, the
WARNING FILTER indicator lights orange and let you know the
filter replacement is required.
If the indicator is lighting orange, turn off the projector and replace
WARNING FILTER
lights orange
the air filter immediately.
Using the projector with the WARNING FILTER indicator lighting
may result in internal heat build up and cause damage to the
optical elements inside the projector. The projector will shutdown
automatically to protect itself when the projector's inside
temperature is abnormally high.
Turn off the projector, and disconnect the AC power cord
from the AC outlet.
1
Pulling down the tabs on both sides top of the filter cover,
open the projector cover.
2
Pull out the air filter from the projector.
3
Filter cover
Replace the new air filter and the filter cover properly onto
the projector.
4
Reset the Filter time. See “Filter” in the Special menu on
p59.
5
Air filter
CAUTION
Do not operate a projector with Air Filter removed. Dust
may accumulate on LCD Panel and Mirror degrading
picture quality.
Do not put small parts into Air Intake Vents. It may result
in malfunction of a projector.
RECOMMENDATION
We recommend avoiding dusty/smoky environments when
✔Note:
operating a projector. Usage in these environments may
• The projector cannot be operated with the air filter removed;
cause poor image quality.
it will shut down automatically if the air filter is removed
while the projector is operating.
• Used in a place where the air pressure is relatively low such
as highlands, the WARNING FILTER indicator may light
orange even the air filter is clean.
When using under dusty or smoky conditions, dust may
accumulate on liquid crystal panel, lens, or optical elements inside
it. This condition may degrade quality of projected image.
When above symptoms are noticed, contact your authorized
dealer or service station for proper cleaning.
ORDER REPLACEMENT FILTER
When ordering the replacement air filter, give the following information to the dealer.
● Model No. of your projector
:
:
PLC-XF60 / PLC-EF60
610 315 1588
● Replacement Filter Part No.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Cleaning
Lamp Replacement
When the life of the projection lamp of this projector draws to an
end, the LAMP1 and 2 REPLACE indicators light orange. If this
indicator lights orange, replace the lamp with a new one promptly.
Top Control
CAUTION
For continued safety, replace with a lamp of the same
type. Do not drop a lamp or touch a glass bulb! The
glass can shatter and may cause injury.
LAMP 1 REPLACE
indicator
LAMP 2 REPLACE
indicator
Allow a projector to cool, for at least 45 minutes before
you open the Lamp cover. The inside of the projector
can become very hot.
These indicators light orange when the life of the
projection lamps draws to an end.
Lamp covers
Follow these steps to replace the lamp.
Turn off the projector and disconnect the AC plug. Allow the
projector to cool for at least 45 minutes.
1
Loosen each screw on the lamp covers with a screwdriver,
and remove the lamp covers.
2
Loosen 2 screws of each lamp with a screwdriver and pull
out one lamp and another with grasping the handle.
3
Replace the lamp with a new one and tighten the 2 screws
back into the positions. Make sure that the lamp is set
properly. Replace the lamp covers and tighten the screws.
4
Screws
(Unremovable)
Connect the AC power cord to the projector and turn on the
projector.
5
Lamp 1
Lamp 2
Reset the Lamp time.
6
See “Lamp time” on p59.
Handle
CAUTION :
DO NOT OPERATE A PROJECTOR WHILE ANY OF LAMPS IS
REMOVED. IT MAY RESULT IN MALFUNCTIONS, FIRE
HAZARD, OR OTHER ACCIDENTS.
Screws
Handle
NOTES ON LAMP REPLACEMENT:
TO MAINTAIN QUALITY OF PICTURE (BETTER BALANCE OF
COLOR AND BRIGHTNESS IN THE ENTIRE SCREEN), WE
RECOMMEND REPLACING ALL 2 LAMPS AT A TIME.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Cleaning
ORDER REPLACEMENT LAMP
Replacement Lamp can be ordered through your dealer. When ordering a Projection Lamp, give the following
information to the dealer.
● Model No. of your projector
:
:
PLC-XF60 / PLC-EF60
POA-LMP80
● Replacement Lamp Type No.
(Service Parts No. 610 315 7689)
LAMP HANDLING PRECAUTIONS
This projector uses a high-pressure lamp which must be handled carefully and properly. Improper handling may result
in accidents, injury, or create a fire hazard.
● Lamp lifetime may differ from lamp to lamp and according to the environment of use. There is no guarantee of the
same lifetime for each lamp. Some lamps may fail or terminate their lifetime in a shorter period of time than other
similar lamps.
● If the projector indicates that the lamp should be replaced, i.e., if the LAMP REPLACE INDICATOR lights up,
replace the lamp with a new one IMMEDIATELY after the projector has cooled down.
( Follow carefully the instructions in the LAMP REPLACEMENT section of this manual.) Continuous use of the
lamp with the LAMP REPLACE INDICATOR lighted may increase the risk of lamp explosion.
● A Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its lifetime draws
to an end. Risk of explosion may differ according to the environment or conditions in which the projector and lamp
are being used.
IF A LAMP EXPLODES, THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TAKEN.
If a lamp explodes, disconnect the projector’s AC plug from the AC outlet immediately. Contact an authorized service
station for a checkup of the unit and replacement of the lamp. Additionally, check carefully to ensure that there are
no broken shards or pieces of glass around the projector or coming out from the cooling air circulation holes. Any
broken shards found should be cleaned up carefully. No one should check the inside of the projector except those
who are authorized trained technicians and who are familiar with projector service. Inappropriate attempts to service
the unit by anyone, especially those who are not appropriately trained to do so, may result in an accident or injury
caused by pieces of broken glass.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Cleaning
Cleaning the Projection Lens
Follow these steps to clean the projection lens.
Disconnect the AC power cord before cleaning.
1
Softly wipe the projection lens with a cleaning cloth that
contains a small amount of non-abrasive camera lens
cleaner, or use lens cleaning paper or a commercially
available air blower to clean the lens. Avoid using an
excessive amount of cleaner. Abrasive cleaners, solvents, or
other harsh chemicals might scratch the surface.
2
When the projector is not in use, replace the lens cover.
3
Cleaning the Projector Cabinet
Follow these steps to clean the projector cabinet.
Disconnect the AC power cord before cleaning.
1
Softly wipe the projector body with a soft, dry cleaning cloth.
When it is heavily soiled, use a small amount of mild
detergent and finish with a soft, dry cleaning cloth. Avoid
using an excessive amount of cleaner. Abrasive cleaners,
solvents, or other harsh chemicals might scratch the surface.
2
When the projector is not in use, put the projector in an
appropriate carrying case to protect it from dust and
scratches.
3
Attaching the Cord Cover Strap
String hole
When mounting the projector on the ceiling, connect the front
cover to the projector with the provided cord cover strap to avoid
the front cover from falling down.
Race the string through a hole on right edge of the
projector's terminal area.
1
Fix the string to a hole inside the front cover with the screw.
2
Screw
Hole
Cord Cover
Strap
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Cleaning
Indicators and Projector Condition
Main Indicators
Indicators
Projector Condition
WARNING
TEMP
READY
Green
LAMP
Red
Red
The projector is OFF. (The AC power cord is unplugged.)
The projector is preparing for stand-by or the projection lamp is being cooled
down. The projector cannot be turned on until cooling is completed.
The projector is ready to be turned on with the POWER ON-OFF button.
The projector is operating normally.
The projector is in the Power management mode.
The temperature inside the projector is abnormally high. The projector cannot
be turned on. When the projector is cooled down enough and the
temperature returns to normal, the LAMP indicator lights red and the projector
can be turned on.
The projector has been cooled down enough and the temperature returns to
normal. When turning on the projector, the WARNING TEMP indicator stops
blinking. Check and clean the air filters.
The projector detects an abnormal condition and cannot be turned on. Unplug
the AC power cord and plug it again to turn on the projector. If the projector is
turned off again, disconnect the AC power cord and contact the dealer or the
service center for service and checkup. Do not leave the projector on. It may
cause electric shock or a fire hazard.
READY, WARNING
TEMP, SHUTTER,
WARNING FILTER, LAMP
1 REPLACE AND LAMP 2
REPLACE indicators are
blinking all together.
• • • Off
• • • Lighting
• • • Dim lighting
• • • Blinking
LED Conditions:
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Cleaning
Shutter Indicator
Indicators
Projector Condition
LAMP
Red
READY
Green
SHUTTER
Blue
The shutter is released. (The projector is On.)
In Shutter management mode. (The projector is in the stand-by mode.)
In Shutter management mode. (The projector is in the cooling mode.)
Slow
Slow
The shutter is out of control. (The projector is in the stand-by mode.) In this
case, contact the service station immediately.
Fast
Fast
The shutter is out of control. (The projector is in the cooling mode.) In this
case, contact the service station immediately.
Warning Filter Indicator
Indicators
Projector Condition
WARNING
LAMP
Red
READY
Green
FILTER
Orange
The air filter is clogged with dust or has been used overtime.
Slow
The air filter has been used overtime.
The air filter is not installed.
Fast
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Cleaning
Lamp Replace Indicators
Indicators
Projector Condition
LAMP 1/2
LAMP
Red
READY
Green
REPLACE
Orange
The lamp cannot light up. (The projector is preparing for stand-by or the
projection lamp is being cooled down. The projector cannot be turned on until
cooling is completed. )
Slow
Slow
The lamp cannot light up. (The lamp has been cooled down enough and the
projector is in stand-by mode and ready to be turned on with the POWER ON-
OFF button.)
The lamp is not installed in the projector.
Fast
The lamp of which indicator is blinking has been used overtime. Replace the
lamp and then reset the Lamp time. The indicator will turn off.
Both
Either lamp cover is not replaced or fit in.
Both of the indicators keeps blinking three times at regular intervals and the
projector cannot be turned on.
Slow
Alternate
One lamp is different from the other in wattage. (For example, installed a
lamp on 300W and the other on 100W.) If the POWER button is pressed in
this condition, the projector will be turned on with Lamp 1 only and then shut
down automatically 1 minute later.
Slow
✽ When the LAMP 1 REPLACE indicator and the LAMP 2 REPLACE indicator light orange, replace the projection lamps with new ones
promptly. And then reset the Lamp time after replacement of the lamps. See page 59, 64 and 65.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Troubleshooting
Before calling your dealer or service center for assistance, check the items below once again.
– Make sure you have properly connected the projector to peripheral equipment as described on page 22~25.
– Make sure all equipment is connected to AC outlet and the power is turned on.
– When you operate the projector with a computer and it does not project an image, restart the computer.
See Information by pressing the INFO. button to check the current projector condition before trying the solutions
below.
Problem:
– Solutions
No power
– Plug the power cord of the projector into the AC outlet.
– Make sure the Main On/Off switch is on.
– See if the LAMP indicator lights red.
– Wait 90 seconds after the projector is turned OFF when turning the
projector back on. The projector can be turned on after the READY indicator
turns green. (☞ “Turning Off the Projector” on page 29)
– Check the WARNING TEMP. indicator. If the WARNING TEMP. indicator
lights red, the projector cannot be turned on.
(☞ "Warning Temp Indicator" on page 62)
– Check the projection lamp. (☞ page 64)
– Unlock Key lock for the projector in the Setting Menu. (☞ page 56)
– Check if the air filter is fully installed and the filter cover is completely
closed. (☞ page 63)
– Check the wattage of two lamps are the same. (☞ page 59, 64)
Image is out of focus.
– Adjust focus of the projector. (☞ page 30)
– Check the projection lens to see if it needs cleaning. (☞ page 66)
– Moving the projector from a cool to a warm place may result in moisture
condensation on the projection lens. In such cases, leave the projector
OFF and wait until condensation disappears.
No image
– Check the connection between your computer or video equipment
and the projector. (☞ page 22–25)
– See if the input signal is correctly output from your computer. Some
laptop computers may need to change the setting for monitor output when
connecting to a projector. See your computer’s instruction manual for the
setting.
– It takes about 20 seconds to display an image after turning on the projector.
– See if the selected system is corresponding with your computer or video
equipment. (☞ page 39–40)
– Select correct input source once again through menu operation.
(☞ page 37–38)
– Make sure the temperature is not out of the specified Operating
Temperature (5°C ~ 35°C).
– Check if the shutter is released. (☞ page 30)
Image is dark.
– Adjust Brightness and Contrast in the Image adjust menu. (☞ page 45)
– Check the Shutter level. (☞ page 55)
– Check each lamp condition and the LAMP 1/2 REPLACE indicators.
(☞ page 64, 69)
Image is Left/Right reversed.
Image is Top/Bottom reversed.
– Check the Ceiling / Rear item. (☞ “Screen Setting” on page 49.)
– Check the Ceiling item. (☞ “Screen Setting” on page 49.)
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
No sound
– Check audio cable connection from audio input source.
– Adjust the audio source.
– Press the Volume (+) button. (☞ page 33)
– Press the Mute button. (☞ page 33)
Some displays are not seen
during the Operation.
– Check the Display item. (☞ “Setting” on page 54)
Only part of image is displayed.
(Large/Small)
– Check if you are in D. Zoom+/– mode. (☞ page 33, 49)
– Change Aspect setting in the Screen setting menu. (☞ page 48)
– Adjust Display area and Position in the PC adjust menu. (☞ page 42–43)
PIN code dialog box appears at start-up. – PJ PIN code lock is being set. Input a PIN code (1234 or numbers you have
set). (☞ “Enter a PJ PIN Code” on page 28 and 57)
Image is not displayed on the
monitor connected to the ANALOG
OUT terminal.
– Select Input 1 with the Input button on the top control or the INPUT 1 button
on the remote control, or through the Input Menu. (☞ page 31and 37)
– Make sure Analog out is "On". (☞ "Setting" on page 55)
The Top Control does not work.
– Check if the Keylock function is set. (☞ "Setting" on page 56)
The Wireless Remote Control
does not work.
– Check the batteries. When replacing, the two batteries should be replaced
at the same time. (☞ page 17)
– Make sure no obstruction is between the projector and remote control.
– Make sure you are not too far from the projector when using the remote
control. Maximum operating range is 32.8’ (10m).
– Make sure the ID and CH of the remote control is conformed to the
projector. (☞ page 16 and 53)
– Initialize the remote control ID and CH, and then initialize the remote control
ID and CH of the projector as well. (☞ page 16 and 53)
– Unlock Key lock for the remote control in the Setting Menu. (☞ page 56)
– Make sure the wired remote cable is not connected to the projector.
(☞ page 26)
When all the solutions above fail, try Factory default in the Setting menu.
(☞ page 58)
USB mouse does not operate properly. – Check cable connection of the USB mouse and the projector. (☞ page 26)
SHUTTER button does not operate.
– Make sure Shutter protection is "Off". (☞ "Setting" on page 55)
Lens position moves when Input
is switched.
– Check Lens memory for each input. (☞ "Setting" on page 55)
Some operating menu items do not appear. – Check the My menu setting. (☞ "Setting" on page 51)
WARNING :
High voltages are used to operate this projector. Do not attempt to open the cabinet.
after following all operating instructions,
Give the model number and explain about the problem. We will advise you how to obtain service.
If problems still persist
service center.
contact the dealer where you purchased the projector or the
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Compatible Computer Specifications
Basically this projector can accept a signal from all computers with V, H-Frequency mentioned below and less
than 230 MHz of Dot Clock.
ON-SCREEN
DISPLAY
H-Freq.
(kHz)
V-Freq.
(Hz)
ON-SCREEN
DISPLAY
H-Freq.
(kHz)
V-Freq.
(Hz)
RESOLUTION
RESOLUTION
VGA 1
VGA 2
VGA 3
VGA 4
VGA 5
VGA 6
VGA 7
MAC LC13
MAC 13
480i
640 x 480
720 x 400
640 x 400
640 x 480
640 x 480
640 x 480
640 x 480
640 x 480
640 x 480
31.47
31.47
31.47
37.86
37.86
37.50
43.269
34.97
59.88
70.09
70.09
74.38
72.81
75.00
85.00
66.60
66.67
60.00
50.00
59.88
50.00
56.25
60.32
75.00
85.06
72.19
61.03
55.38
60.51
60.31
51.09
60.51
74.55
60.00
84.997
75.03
70.07
74.92
60.02
54.58
79.35
87.17
77.07
75.70
86.96
58.20
58.30
XGA15
MAC 19
MAC 21
SXGA 1
SXGA 2
SXGA 3
SXGA 4
SXGA 5
SXGA 6
SXGA 7
SXGA 8
SXGA 9
SXGA 10
SXGA 11
SXGA 12
SXGA 13
SXGA 14
SXGA 15 1280 x 1024
SXGA 16 1280 x 1024
SXGA 17
SXGA 18
SXGA 19 1280 x 1024
SXGA 20 1280 x 1024
SXGA 21 1400 x 1050
MAC
MAC
1024 x 768
1024 x 768
1152 x 870
1152 x 864
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 960
1152 x 900
1152 x 900
58.03
60.24
68.68
64.20
62.50
63.90
63.34
63.74
71.69
81.13
63.98
79.976
72.0
75.08
75.06
70.40
58.60
60.00
59.98
60.01
67.19
76.107
60.02
75.025
60.00
65.20
75.60
86.00
94.00
60.01
72.00
66.00
86.70
60.18
85.024
60.00
75.08
75.08
60.00
60.00
60.00
72.00
60.00
65.00
70.00
75.00
60.00
60.00
60.00
50.00
35.00
––––––––
(Interlace)
15.734
15.625
31.47
31.25
35.156
37.88
46.875
53.674
48.08
37.90
34.50
38.00
38.60
32.70
38.00
49.72
48.36
68.677
60.023
56.476
60.31
48.50
44.00
63.48
36.00
62.04
61.00
35.522
46.90
47.00
––––––––
(Interlace)
––––––––
(Progressive)
––––––––
(Progressive)
575i
480p
575p
60.00
61.20
71.40
50.00
50.00
63.37
76.97
61.85
46.43
63.79
91.146
63.90
75.00
80.00
48.36
47.70
48.36
56.16
75.00
81.25
87.50
93.750
45.00
33.75
33.75
28.125
SVGA 1
SVGA 2
SVGA 3
SVGA 4
SVGA 5
SVGA 6
SVGA 7
SVGA 8
SVGA 9
SVGA 10
SVGA 11
MAC 16
XGA 1
XGA 2
XGA 3
XGA 4
XGA 5
XGA 6
XGA 7
XGA 8
XGA 9
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1280 x 1024
(Interlace)
1280 x 1024
(Interlace)
1152 x 900
1280 x 1024
(Interlace)
1280 x 960
1280 x 1024
1366 x 768
1360 x 768
1376 x 768
1360 x 768
1600 x 1200
1600 x 1200
1600 x 1200
1600 x 1200
WXGA 1
WXGA 2
WXGA 3
WXGA 4
UXGA 1
UXGA 2
UXGA 3
UXGA 4
720p
1024 x 768
(Interlace)
––––––––
(Progressive)
––––––––
(Interlace)
––––––––
(Interlace)
XGA 10
XGA 11
XGA 12
XGA 13
XGA 14
1024 x 768
1024 x 768
1035i
1080i/60
1080i/50
1024 x 768
(Interlace)
––––––––
(Interlace)
1024 x 768
1024 x 768
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
When a input signal is digital from DVI terminal, refer to chart below.
ON-SCREEN
DISPLAY
H-Freq.
(kHz)
V-Freq.
(Hz)
ON-SCREEN
DISPLAY
H-Freq.
(kHz)
V-Freq.
(Hz)
RESOLUTION
RESOLUTION
D-VGA
D-480p
D-575p
D-SVGA
D-XGA
D-WXGA1
D-WXGA2
D-WXGA3
640 x 480
31.47
31.47
31.25
37.879
43.363
48.36
47.70
48.36
59.94
59.88
50.00
60.32
60.00
60.00
60.00
60.00
D-SXGA1 1280 x 1024
D-SXGA2 1280 x 1024
63.98
60.276
75.00
45.00
33.75
33.75
28.125
60.02
58.069
60.00
60.00
60.00
60.00
50.00
720 x 480
(Progressive)
768 x 575
(Progressive)
D-UXGA
D-720p
D-1035i
D-1080i/60
D-1080i/50
1600 x 1200
1280 x 720
800 x 600
1024 x 768
1366 x 768
1360 x 768
1376 x 768
(Progressive)
1920 x 1035
(Interlace)
1920 x 1080
(Interlace)
1920 x 1080
(Interlace)
Proper image may not be obtained in some signals. Specifications are subject to change without notice.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Technical Specifications
Mechanical Information
Projector Type
Multi-media Projector
Dimensions (W x H x D)
Net Weight
Feet Adjustment
20.39" x 9.92" x 23.86" (518mm x 252mm x 606mm) (Not including adjustable feet)
54.3 lbs (24.7kgs)
0˚ to 3.65˚
Panel Resolution
PLC-XF60
PLC-EF60
LCD Panel System
Panel Resolution
Number of Pixels
1.4" TFT Active Matrix type, 3 panels
1024 x 768 dots
2,359,296 (1024 x 768 x 3 panels)
1400 x 1050 dots
4,410,000 (1400 x 1050 x 3panels)
Signal Compatibility
Color System
High Definition TV Signal
Scanning Frequency
PAL, SECAM, NTSC, NTSC4.43, PAL-M, PAL-N
480i, 480p, 575i, 575p, 720p, 1035i, and 1080i
H-sync. 15 ~ 120 KHz, V-sync. 48 ~ 120 Hz
Optical Information
Projection Image Size (Diagonal)
Projection Lens
Subject to Optional lens
Option
Throw Distance
Projection Lamp
Subject to Optional lens
300W
Interface
Input 1 terminals
DVI-D Terminal (Digital in) (HDCP Compatible) x1, (VGA) HDB15 Terminal X 2 (Analog In/
Analog Out) and Mini Jack (stereo) x 1
Input 2 terminals
Input 3 terminals
BNC Type x 5 (G/ VIDEO/Y, B/ Cb/Pb, R/ Cr/Pr, H/V, V) and Mini Jack (stereo) x 1
RCA Type x 3 (VIDEO/Y, Cb/Pb, Cr/Pr), Mini DIN 4 pin x 1 (S-Video) and RCA Type x 2
(Audio R and L(mono))
Input 4 terminals
DVI-D Terminal (Digital in) (HDCP Compatible) x1, Serial port In (DB9) x 1 and
Serial port Out (DB9) x1
Other Terminals
SERIAL PORT IN
SERIAL PORT OUT
USB Connectors
R/C Jack
DB9 pin x 1
DB9 pin x 1
USB Series A receptacle x 1 and USB Series B receptacle x 1
Mini Jack x 1
Audio
Internal Audio Amp
Built-in Speaker
3.0W RMS
2 speaker, ø2.05" (52mm)
Power
Voltage and Power Consumption
AC 100 ~ 120 V (9.5 A Max. Ampere), 50 / 60 Hz (The U.S.A and Canada)
AC 200 ~ 240 V (4.5 A Max. Ampere), 50 / 60 Hz (Continental Europe and The U.K.)
Operating Environment
Operating Temperature
Storage Temperature
41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)
14 ˚F ~ 140 ˚F (-10˚C ~ 60 ˚C)
Remote Control
RF Remote Standard
Frequency Band
Battery
Operating Range
Dimensions
2.4 GHz Low Power Radio
2.472GHz (CH1: default setting), 2.403GHz (CH2), 2.446 GHz (CH3), and 2.421GHz (CH4)
AA, UM3 or LR6 1.5V ALKALINE Type x 2
Within 32.8' (10m)
2.0” x 1.2” x 7.1” (50mm x 30mm x 181mm)
0.33 lbs (150 g) (including batteries)
Net Weight
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Accessories
Owner's Manual
AC Power Cord
Remote Control and Batteries
DVI-D Cable
VGA Cable
Wired Remote Cable
Lens Attachment
Light Block Plates (2types)
Advanced Screen Manager (CD-ROM)
Real Color Manager Pro (CD-ROM)
Protective Dust Cover
Cord Cover Strap
Security Label (PIN Code/USB Key)
● The specifications are subject to change without notice.
● LCD panels are manufactured to the highest possible standards. Even though 99.99% of the pixels are effective, a tiny fraction of
the pixels (0.01% or less) may be ineffective by the characteristics of the LCD panels.
● The On-Screen Menu and figures in this manual may differ slightly from the product.
Optional Parts
The parts listed below are optionally available. When ordering those parts, give the item name, Model No. and Option
Control No. (if necessary) to the sales dealer.
Model No.
SCART-VGA Cable
: POA-CA-SCART
(This cable is used for RGB Scart 21-Pin
Video output of video equipment.)
Projector USB Key
: POA-USB01
: POA-SR-140
: POA-CA-RC30
Model No.
Smoke Resist Box
Wired Remote Cable (30m)
Optional Interface Board
Advanced Network
Dual SDI
: POA-MD19NET (Option Control No. 06)
: POA-MD17SDID
Faroudja
: POA-MD09VD3
DVI (HDCP compatible)
D-Sub
: POA-MD18DVI
: POA-MD04VGA
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Menu Tree
Input 1
RGB (PC Analog)
System (1)
INPUT
RGB (Scart)
Auto
RGB (PC Digital)
RGB (AV HDCP)
System (1)
System (1)
RGB
Input 2
Input 3
System (1)
System (2)
System (3)
System (2)
Video
Y, Pb/Cb, Pr/Cr
Video
Y, Pb/Cb, Pr/Cr
S-Video
System (3)
Warp & Blending Board
System (1)
Input 4
Input 5
Optional Slot
SYSTEM
SYSTEM
(2)
SYSTEM
(3)
Mode 1
XGA 1
XGA 3
XGA 5
Quit
Auto
PAL
Auto
1080i
1035i
720p
575p
480p
575i
(1)
SECAM
NTSC
NTSC4.43
PAL-M
PAL-N
Quit
✽Systems displayed in the System Menu vary
depending on an input signal.
480i
Quit
Auto PC adj.
Fine sync
Total dots
Current mode
Clamp
SCREEN
SETTING
PC ADJ.
Screen
Normal
Wide
True
0 - 31
Full screen
Custom
Phase
Scale
H
V
Width
H&V
Display area
Position
H
V
Position
H
V
H
Common
Reset
V
Yes/No
Yes/No
V sync. phase
0 - 15
Quit
Reset
Mode
Yes/No
Store
Free
D. Zoom
Keystone
Ceiling
Rear
D. Zoom+/D. Zoom–
Store/Reset
Off/On
Quit
Off/On
Quit
SOUND
Volume
Treble
0 - 63
-15 ~ +15
-15 ~ +15
Off/On
Bass
Mute
Quit
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
English
German
French
IMAGE
Standard (AV)
Cinema
Standard (PC)
Real
SETTING
Language
Italian
Spanish
Portuguese
Dutch
Swedish
Russian
Chinese
Korean
Image 1
Image 2
Image 3
Image 4
Image 5
Image 6
Image 7
Image 8
Image 9
Image 10
Quit
Japanese
Position
Menu
Logo
My menu
Simple menu
Logo select
Off/On
Default
My logo
Off
Contrast
Brightness
Color
0 - 63
0 - 63
0 - 63
0 - 63
Color
IMAGE
ADJ.
Yes/No
Capture
Off/On
Lock
Tint
PIN code change
Blue
Color management
Background
Lamp
Gamma
List
My logo
Black
All Del
Menu
Color. M
Menu
Control
Normal
Color. M
Auto
Eco
Auto picture control
Color temp.
Off
L1
L2
Mode
2-Lamp
1-Lamp
Auto
Lamp1
Lamp2
Remote control code
CH 1– 4
ID 1– 8
Off/On
Off/On
XLow
Low
Mid
Display
Input search
Power management
Off/Ready/Shut down
1 ~ 60 minutes
High
Red
0 - 63
0 - 63
0 - 63
0 - 15
0 - 15
Off
On start
Off/On
Off/On
Green
Analog out
Blue
Input 1–5
Off
Lens memory
Memory
Normal
Sharpness
Gamma
Noise reduction
Level
Shutter
High contrast
Remote control
Projector
Protection
L1
L2
Management
5 ~ 180 minutes
Progressive
Off/On
Projector
Security
Key lock
Film
Off/On
Remote control
Reset
Store
Yes/No
Image 1
Image 2
Image 3
Image 4
Image 5
Off
Setting
USB Lock
PJ lock
On 1
On 2
Off
Registration
Delete
On 1
The USB plugged in
The other USB
Image 6
Image 7
Image 8
Image 9
Image 10
On 2
Off
PJ PIN code change
Factory default
Quit
Yes/No
Quit
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
INFORMATION
Input
System
Signal
Screen
Language
Lamp mode
Lamp status
Power management
Shutter management
Smoke resist
Option filter time
Security
Remote control
Quit
W
Lamp
Lamp 1
SPECIAL
Hour(s)
Reset
W
Yes/No
Yes/No
Lamp 2
Normal
Hour(s)
Reset
Fan control
Max
Projector
Hour(s)
Reset
Filter
Yes/No
Yes/No
Option box
Hour(s)
Reset
Off/On
Auto PC adj.
Test pattern
Cross 1 (W)
Cross 2 (R)
Cross 3 (G)
Cross 4 (B)
Cross 5 (M)
Cross 6 (C)
Cross 7 (Y)
Gradation 1~4
Color
Flat 1~8
Baud rate
9600
RS–232C
19200
Projector ID
Default
001 – 999
Yes/No
Save
USB memory 1–10
Quit
PC mode
USB memory
USB memory 1–10
Quit
Load
USB memory 1–10
Quit
Delete
Image adj.
USB memory 1–10
Quit
Save
Load
USB memory 1–10
Quit
Warning log
Quit
USB memory 1–10
Quit
Delete
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Dimensions
Unit : inch (mm)
7.24 (184)
20.39 (518)
9.92 (252)
5.28 (134)
3.65˚ (Max.)
23.86 (606)
18.11 (460)
1.08 (27.5)
13.58 (345)
Screw Holes for Ceiling Mount
Screws: M8
Depth: 0.31(8.0)
18.27 (464)
15.91 (404)
2.36 (60)
9.15 (232.5)
9.15 (232.5)
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Terminal Configurations
ANALOG INPUT / OUTPUT TERMINAL (ANALOG)
Terminal : HDB15-PIN
1
2
3
4
5
6
7
8
Red (R/Cr) Input / Output
9
-----
Green (G/Y) Input / Output
Blue (B/Cb) Input / Output
-----
Ground (Horiz.sync.)
Ground (Red)
10 Ground (Vert.sync.)
11 Ground / -----
12
13 Horiz. sync. Input/Output (Composite H/V sync.)
14 Vert. sync.
15
2
1
5
4
3
10
9
8
7
6
15
14
13
12
11
-----
Ground (Green)
Ground (Blue)
-----
DVI-D TERMINAL (DIGITAL)
Terminal : DVI-D
1
2
3
4
5
6
7
8
T.M.D.S. Data2–
T.M.D.S. Data2+
9
T.M.D.S. Data1–
17 T.M.D.S. Data0–
18 T.M.D.S. Data0+
10 T.M.D.S. Data1+
1
9
2
3
4
5
6
7
8
10 11 12 13 14 15 16
T.M.D.S. Data2 Shield 11 T.M.D.S. Data1 Shield 19 T.M.D.S. Data0 Shield
17 18 19 20 21 22 23 24
No Connect
No Connect
DDC Clock
DDC Data
12 No Connect
13 No Connect
14 +5V Power
15 Ground (for +5V)
16 Hot Plug Detect
20 No Connect
21 No Connect
22 T.M.D.S. Clock Shield
23 T.M.D.S. Clock+
24 T.M.D.S. Clock–
No Connect
SERIAL PORT IN /OUT TERMINAL
Terminal : DIB 9-PIN
Serial
-----
R X D
T X D
-----
GND
-----
-----
1
2
3
4
5
6
7
8
9
5
3
4
2
1
9
8
7
6
-----
-----
USB CONNECTOR (Series B)
Series B
1
Vcc
2
3
1
4
2
3
4
- Data
+ Data
Ground
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
PIN Code Number Memo
Write down the PIN code number in the column below and keep it with this manual securely. If you forgot or lost the
number and unable to operate the projector, contact the service station.
PIN Code Lock No.
Factory default set No: 1 2 3 4*
Logo PIN Code Lock No.
Factory default set No: 4 3 2 1*
*Should the four-digit number be
changed, the factory set number will
be invalid.
While the projector is locked with the PIN code or USB key...
Put the appropriate label (supplied) on in a prominent place of the
projector's body while it is locked with a PIN code or USB key.
PIN code label
Pixelworks ICs used.
This symbol on the nameplate means the product is
The CE Mark is a Directive conformity
mark of the European Community (EC).
Listed by Underwriters Laboratories Inc. It is designed
and manufactured to meet rigid U.L. safety standards
against risk of fire, casualty and electrical hazards.
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Index
Filter Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Numerics
A
Adjustable Feet . . . . . . . . . . . . . . . . . . . . . . . . . . .9, 19
Auto PC Adjustment . . . . . . . . . . . . . . . . . . . . . . . . .31
G
H
B
C
I
Color Management . . . . . . . . . . . . . . . . . . . . . . . . . .45
Connecting to Video Equipment . . . . . . . . . . . . .24, 25
K
L
Lamp Replacement . . . . . . . . . . . . . . . . . . . . . . . . . .64
D
F
M
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Shutter protection . . . . . . . . . . . . . . . . . . . . . . . . . . .55
N
O
Network Manager . . . . . . . . . . . . . . . . . . . . . . . . . . .75
Noise reduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
T
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
P
Panel Resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
U
V
R
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Remote Control Channel and ID . . . . . . . . . . . . . . . .16
REPLACEMENT LAMP . . . . . . . . . . . . . . . . . . . .63, 65
W
Warp & Blending . . . . . . . . . . . . . . . . . . . . . . . . . .2, 23
Z
S
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Printed in Japan
Part No. 610 315 6262 (1AA6P1P4588-- MM7A)
SANYO Electric Co., Ltd
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Regency Indoor Fireplace P33 LP3 User Guide
Revolabs Microphone XG 80 User Guide
Rival Slow Cooker Slow Cookers User Guide
Roland Electronic Keyboard 5100001499 User Guide
Rolls Speaker PS84 User Guide
Ruby Tech Switch GS 2124C User Guide
Samsung DVD Player DVD S425 User Guide
Samsung Flat Panel Television LE15E31S User Guide
Sansui Flat Panel Television SLED2237 User Guide
SATO Printer MI 4208 4308 User Guide