Sanyo Home Security System vcc zm300p User Guide

INSTRUCTION MANUAL

BEDIENUNGSANLEITUNG

MANUEL D’INSTRUCTIONS

VCC-ZM300P

COLOUR CCD ZOOM camera

CCD-Farb-Zoomkamera

Caméra CCD COULEURS avec ZOOM

CCD

About this manual

Before installing and using the camera, please read this manual

carefully. Be sure to keep it handy for later reference.

A propos de ce manuel

Avant d’installer et d’utiliser la caméra, veuillez lire ce

manuel attentivement. Gardez-le à portée de main pour

toute référence ultérieure.

Über diese Bedienungsanleitung

Lesen Sie bitte vor der Montage und dem Inbetriebnehmen der

Kamera zuerst diese Bedienungsanleitung sorgfältig durch und

bewahren Sie sie zum späteren Nachschlagen auf.

Download from Www.Somanuals.com. All Manuals Search And Download.

MAIN FEATURES

ACCESSORIES

• Built in Interline transfer method 1/4” CCD, approx. 470,000

picture elements.

Clamping core..........................................................................1 pc.

• High sensitivity, minimum required illumination is 2.0 lux.

(F1.6, gain max)

• More than 520 TV lines of horizontal resolution.

• Equipped with intelligent Backlight compensation.

• Special Gamma mode (contrast up)

• Built in high speed electronic shutter and slow shutter.

• 32X Electronic sensitivity

• Built in Digital Motion Detection

• Built in Privacy masking function

• 12VDC/24V AC dual operation(electrically isolate) .

• Internal sync. / Line Lock.

• 22x optical zoom and 16x electronic zoom.

• Coaxial control or RS485, operation via SSP.

Download from Www.Somanuals.com. All Manuals Search And Download.

PRECAUTIONS

In case of problem

Protect from high temperatures

Do not use the camera if smoke or a strange odour comes from

the unit, or if it seems not to function correctly. Disconnect the

power cord immediately, and consult your dealer (or a Sanyo

Authorized Service Centre).

Do not install close to stoves, or other heat generating devices,

such as spotlights, etc., or where it could be subject to direct

sunlight, as that could cause deformation, discoloration or other

damages.

Be careful when installing close to the ceiling, in a kitchen or

boiler room, as the temperature may raise to high levels.

Do not open or modify

Do not open the cabinet, as it may be dangerous and cause

damage to the unit. For internal settings and repairs, consult your

dealer (or a Sanyo Authorized Service Centre).

Install where the temperature range will stay between –10°C and

50°C. (no condensation)

Cleaning

Do not put objects inside the unit

• Dirt can be removed from the cabinet by wiping it with a soft

cloth. To remove stains, wipe with a soft cloth moistened with

a soft detergent solution and wrung dry, then wipe dry with a

dry soft cloth.

Make sure that no metal objects or flammable substance get

inside the camera. If used with a foreign object inside, it could

cause a fire, short-circuits or damages.

If water or a liquid gets inside the camera, disconnect the power

cord immediately, and consult your dealer (or a Sanyo Authorized

Service Centre). Be careful to protect the camera from rain, sea

water, etc.

• Do not use benzine, thinner or other chemical product on the

cabinet, as that may cause deformation and paint peeling.

Before using a chemical cloth, make sure to read all

accompanying instructions. Make sure that no plastic or

rubber material comes in contact with the cabinet for a long

period of time, as that may cause damage or paint peeling.

Be careful when handling the unit

To prevent damages, do not drop the camera or subject it to

strong shock or vibration.

Install away from electric or magnetic fields

If installed close to a TV, radio transmitter, magnet, electric motor,

transformer, audio speakers the magnetic field they generate will

distort the image.

Protect from humidity and dust

To prevent damages to the camera, do not install it where there is

greasy smoke or steam, where the dampness may get too high,

or where there is a lot of dust.

Download from Www.Somanuals.com. All Manuals Search And Download.

PARTS NAMES AND FUNCTIONS

4 Menu setting button (SET) (See p8)

Control

Connect the camera to the monitor, then press the SET

button for about 3 seconds to display the on-screen menu.

5 RS-485 control push-lock terminals (RS485, A, B, G)

terminals

SET

Use a cable thicker than AWG22.

ZOOM

COM

OUT

FOCUS

ALARM

RS485

A: Twisted-pair cable terminal

G: Ground terminal

VIDEO OUT

POWER

AC24V

B: Twisted-pair cable terminal

GND

6 24 V AC or 12 V DC input terminals (AC 24 V, DC 12 V,

GND)

DC12V

CLASS 2 WIRING

Lens cap

1 Video output connector (VIDEO OUT: BNC type)

The cap is installed to protect the lens section. Remove the cap

when using the camera.

Connect this connector to a device such as a time lapse VCR or

monitor with a VIDEO IN connector.

2 Power indicator (POWER)

Comes on when the power to the camera is on.

Note: After connecting the power supply the POWER indicator

will blink for 5 seconds. During this time no adjustments

using the menus or any other operation are possible.

3 Cursor button (See p8)

j: Press this button to move the cursor up.

c: Press this button to move the cursor to the right, or to

turn the settings ON/OFF etc.

d: Press this button to move the cursor to the left, or to turn

the settings ON/OFF etc.

l: Press this button to move the cursor down.

Download from Www.Somanuals.com. All Manuals Search And Download.

PARTS NAMES AND FUNCTIONS

Camera installation bracket

Control terminals

The bracket can be fixed at the top or bottom of the camera.

When fixing the bracket, be sure to use the longer screws and

install the shorter screws on the opposite side to seal the

openings.

1 Zoom terminal (ZOOM)

Sets the zoom to wide angle or telescoping.

2 Focus terminal (FOCUS)

Sets the focus to infinite or close range.

3 Grounding terminal (COM)

4 Alarm output terminal (ALARM OUT)

CAUTION: When installing the camera bracket, select a location

that can support the total weight of the camera and

accessories.

A detection alarm based on the motion sensor is sent to

connected equipment such as a buzzer or lamp or a time

lapse VCR device.

5 Alarm input terminal (ALARM IN)

Used for detection of intruders through a connected

external alarm switch.

12345

ZOOM

COM IN

FOCUS

ALARM OUT

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTIONS

Basic connection for monitoring or recording

TV monitor

(sold separately)

AC 24 V connection

DC 12 V connection

(A)

AC24V

GND

DC12V

CLASS

WIR

DC12V

CLASS

WIR

Fig. 1

Fig. 2

(Video signal connections)

Time lapse VCR or

: VIDEO IN

Digital video recorder

: VIDEO OUT

(sold separately)

The peripheral devices (VCR, monitor, lens, etc.) and cables

are sold separately.

CAUTION:

To prevent camera and/or power supply failure, pay close

attention to polarity when making the connections.

1 ^{Make the video signal connection between the camera}

and the monitor or time lapse VCR.

When using this unit, the supplied clamping core A must be

installed on the power cord and BNC cable, in order to

prevent electromagnetic interference to the other devices

connected.

3 ^{Insert the plug of this power supply into a wall outlet.}

The POWER indicator (A) will light. Adjust the picture on the

monitor using the Brightness and Contrast controls.

2 ^{Power supply choices}

• Use a commercially available 24 V AC adaptor. Make sure

to use a cable with an earth line (22AWG or more) to

connect to the grouding terminal. (Fig.1.)

• When using a DC 12 V power supply, make the

connections as indicated in Fig. 2.

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTIONS

Coaxial cable type and maximum length

• Cable type RG-59U (3C-2V), 250 m maximum.

• Cable type RG-6U (5C-2V), 500 m maximum.

• Cable type RG-11U (7C-2V), 600 m maximum.

Connection of peripheral equipment and

controller terminal

External alarm

switch

Buzzer or lamp

• Focus adjustment

CAUTION:

DC–6V/12V: Infinite

DC+6V/12V: Close range

• The RG-59U type cable should not be run through electrical

conduits or through the air.

• Zoom adjustment

DC–6V/12V: Wide angle

DC+6V/12V: Telescoping

• Using CCTV/Video-grade coaxial cable.

A B

CAMERA IN

terminal

Multiplexer

(sold separately)

GAB

RS-485 connector

System controller (sold separately)

Download from Www.Somanuals.com. All Manuals Search And Download.

DISPLAYING/CLOSING THE MENU SCREEN

MAIN MENU screen

Sub-menu screen

MAIN MENU

LANGUAGE

CAMERA ID

SYNC

SET ‚

OFF

LANGUAGE

ENGLISH

FRENCH

SET

LANGUE

INT

SPRACHE

GERMANY

PRIVACY MASK

LENS

SET ‚

OFF

MIRROR

VIEW SETTING

OPTION

‚

SET ‚

OFF

PRESET

END

BACK

Cursor button SET button

1 ^{Press the SET button for about 3 seconds.}

3 ^{Switching to sub-menu screens}

The MAIN MENU screen will appear.

Use the cursor button (j l d c) until an item with a “y”

next to it is flashing, then press the SET button.

2 ^{Using the cursor button}

4 ^{Closing a settings screen}

1 Use the cursor button (l) to move the cursor down.

When the cursor reaches the bottom of the screen, it goes

back up to the top of the screen.

• To return to the previous screen, use the cursor button (l)

to select BACK for MENU, then press the SET button.

2 Use the cursor button (j) to move the cursor up. When

the cursor reaches the top of the screen, it goes back

down to the bottom of the screen.

• To return to the normal screen, use the cursor button (d or

c) to select END for MENU, then press the SET button.

ꢀ Returning to the default setting

Use cursor button (l, then d or c) to change the PRESET

setting to ON, then press the SET button.

3 Use the cursor button (c) to move the cursor to the right.

This button is also used to change ON/OFF settings etc.

4 Use the cursor button (d) to move the cursor to the left.

This button is also used to change ON/OFF settings etc.

Download from Www.Somanuals.com. All Manuals Search And Download.

MENU ITEM FLOW AND MENU OPERATION

MAIN MENU

1 2 3 4 5 6 7 8

LANGUAGE

CAMERA ID

SYNC

PRIVACY MASK

LENS

SET

OFF

INT

SET

OFF

SET

OFF

END

‚

MIRROR

VIEW SETTING

OPTION

‚

PRESET

LANGUAGE setting (See p10)

MIRROR setting (See p21)

Choose from among English, French and German.

The image can be rotated horizontally then vertically or vertically

then horizontally.

CAMERA ID setting (See p11)

SYNC setting (See p12)

VIEW SETTING (See p22)

Different detailed settings can be made for each camera (9

screens). After they are set, these are linked to “VIEW SETTING

(0 – 8)” settings for preset positions.

Sets camera to internal synchronization (INT) or power source

synchronization (L-L).

Power source synchronization, the vertical synchronization phase

as adjusted on a sub-menu screen.

OPTION setting (See p46)

For setting communications conditions and alarms.

PRIVACY MASK setting (See p13)

This covers an area of the screen with a gray pattern for areas

that may infringe on privacy.

Gray patterns can be placed on up to 4 areas.

LENS setting (See p17)

Sets camera to automatic focus or manual focus. Zoom speed and

magnification is also set here.

Download from Www.Somanuals.com. All Manuals Search And Download.

LANGUAGE SETTING

Select one of the languages shown on the menu screen (English, French, German).

MAIN MENU

LANGUAGE

CAMERA ID

SYNC

SET

OFF

INT

SET

OFF

SET

OFF

END

‚

LANGUAGE

ENGLISH

FRENCH

GERMANY

LANGUE

SPRACHE

PRIVACY MASK

LENS

‚

MIRROR

VIEW SETTING

OPTION

‚

LANGUE

PRESET

LANGUAGE

LANGUE

ANGLAIS

FRANCAIS

ALLEMAND

SPRACHE

RETOUR

1 ^{In the MAIN MENU, use the cursor button (}^j^or^l^{) to}

select SET for LANGUAGE, then press the SET button.

The LANGUAGE screen will appear.

2 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

language (example: “FRENCH”) then press the SET

button.

The interface language becomes French.

3 ^{Use the cursor button (}^j^or^l^{) to select RETUOR for}

MENU, then press the SET button.

The MENU PRINCIPAL screen will reappear.

Information in the MAIN MENU screen will appear in the

selected language.

ꢀ Use the cursor button (l) to select FIN, then press the

SET button. The display will return to the normal

monitor screen.

Download from Www.Somanuals.com. All Manuals Search And Download.

CAMERA ID SETTING

Camera ID setting

Camera ID screen

Example: Setting the Camera ID to “CAM 1”

CAMERA ID SETTING

MAIN MENU

CAMERA ID SETTING

ABCDEFGHIJKLM

NOPQRSTUVWXYZ

0123456789 :-‚

LANGUAGE

CAMERA ID

SYNC

SET

INT

SET

OFF

SET

OFF

END

‚

ABCDEFGHIJKLM

NOPQRSTUVWXYZ

0123456789 :-‚

ID ????????????????

PRIVACY MASK

LENS

‚

ID ????????????????

POSITION

SET

‚

MIRROR

VIEW SETTING

OPTION

‚

POSITION

SET

‚

PRESET

OFF

BACK

PRESET

OFF

BACK

1 Character selection palette:

1 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

CAMERA ID, and then use the cursor button (d or c) to

change the setting to ON. Then press the SET button.

By moving the cursor to letters or numbers in this

palette, you can select characters.

Selected characters will appear in the corresponding

field under ID.

The CAMERA ID SETTING screen will appear.

2 ID:

2 ^{Use the cursor button (}^{j l d c}^{) to move the cursor to}

the letter “C” in the character selection palette, then

press the SET button.

The ID entry field shows 16 question marks (?). The ID

will not be displayed on the screen.

3 POSITION:

ꢀ After at least one character is displayed in the ID field,

the carriage return mark (y) will appear at the lower

right corner of the character selection palette. Selecting

this mark between the characters of the field will create

a new line at that place.

After characters are displayed in the ID field, moving

the cursor to the POSITION field with the cursor button

and pressing the SET button will display the camera ID

on the normal screen.

4 PRESET:

3 ^{Use the same steps to select “A”, “M” and “1” from the}

palette, then press the SET button.

When this item is turned to ON, the ID fields are

cleared (question marks appear). Use this function

when you want to change the ID.

The characters “CAM1” appear in the ID field.

ID CAM1????????????

Download from Www.Somanuals.com. All Manuals Search And Download.

CAMERA ID SETTING

SYNC SETTING (SYNC)

Initial setting is internal synchronization (INT), so it does not need

to be set again. Follow the steps below to change the setting to

power source synchronization (L-L).

4 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

POSITION, and then press the SET button.

The camera ID will be displayed on one line.

Power source synchronization (L-L) setting

CAMERA ID SETTING

CAM1

ABCDEFGHIJKLM

NOPQRSTUVWXYZ

0123456789 :-‚

MAIN MENU

L-L SETTING

(V SYNC PHASE)

ú------+------ü

Camera ID

ID CAM1????????????

LANGUAGE

CAMERA ID

SYNC

SET

OFF

INT

SET

OFF

SET

OFF

END

‚

POSITION

SET

‚

PRESET

OFF

BACK

PRIVACY MASK

LENS

‚

MIRROR

VIEW SETTING

OPTION

‚

(Displaying the ID on 2 lines.)

PRESET

OFF

BACK

1 Use the cursor button (d or c) to move the cursor to the

location in the ID field where the carriage return is wanted.

Use the cursor button (j l d c) to select L-L for

SYNC, then press the SET button.

The L-L SETTING screen will appear.

2 Use the cursor button (j l d c) to move the cursor to

the carriage return mark (y) at the lower right corner of

the character selection palette, and then press the SET

button.

Use the cursor button (d or c) to adjust the position

of the vertical synchronization indicator shown on the

screen.

The numerical value will change, allowing adjustment of

vertical synchronization.

5 ^{Moving the on-screen title display position}

Use the cursor button (j l d c) to move the title

display to the preferred position on the screen, then

press the SET button.

The CAMERA ID SETTING screen will reappear.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

Download from Www.Somanuals.com. All Manuals Search And Download.

PRIVACY MASK SETTING (PRIVACY MASK)

Mask setting

MAIN MENU

PRIVACY MASK SETTING

PASSWORD LOCK ON ‚

MASK NO.SELECT

MASK 3 SET

(POSITION)

LANGUAGE

CAMERA ID

SYNC

PRIVACY MASK

LENS

SET

OFF

INT

SET

OFF

SET

OFF

END

‚

PASSWORD CHANGE SET ‚

MASK SET SET ‚

MASK

OFF

SET

OFF

‚

MIRROR

VIEW SETTING

OPTION

‚

MASK NO.SELECT

OFF

PRESET

OFF

BACK

SET

‚

MASK

OFF

1 ^{Use the cursor button (}^j^or^l^{) to select SET for}

3 ^{Use the cursor button (}^j^or^l^{) to move the cursor to a}

mask number (Ex: MASK 3), and then use the cursor

button (c) to change the setting to SET. Then press the

SET button.

PRIVACY MASK, then press the SET button.

The PRIVACY MASK SETTING screen will appear.

2 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

The MASK 3 SET (POSITION) screen will appear, and SETy

will be blinking. The gray mask will appear in the center of the

screen.

SET for MASK SET and press the SET button.

The MASK NO. SELECT screen will appear.

Cursor button operation

Note: When PASSWORD LOCK is ON, moving the cursor to

MASK SET and press the SET button to bring up a

password access screen. The password must be entered in

this screen.

OFF: to c side (ON appears), to c side again (SET appears)

• SET: Mask POSITION and SIZE can be set

• ON: Masks can be displayed

• OFF: Masks can be deleted

Download from Www.Somanuals.com. All Manuals Search And Download.

PRIVACY MASK SETTING (PRIVACY MASK)

(About the POSITION screen)

MASK 3 SET

(SIZE)

MASK 3 SET

It is possible to set as many as 4 masks on the same POSITION

screen.

MASK 1

SET

‚

PRESET

OFF

BACK

4 ^{Use the cursor button (j l d c) to move the gray}

mask, then press the SET button.

The SIZE screen will appear, and the mask that was positioned

in the POSITION screen will be displayed.

5 ^{Use the cursor button (j l d c) to adjust the size of}

the gray mask, then press the SET button.

PRESET and MENU will appear at the bottom of the screen.

Move the cursor to BACK for MENU and press the SET button.

The screen will return to MASK NO. SELECT.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

Download from Www.Somanuals.com. All Manuals Search And Download.

PRIVACY MASK SETTING (PRIVACY MASK)

PASSWORD setting

You can lock the privacy masks in place as gray patterns after they have been set. The password requirement is initially set to OFF, but to

begin using it, you must enter the factory set password “1234”.

PRIVACY MASK SETTING

PASSWORD LOCK OFF ‚

PASSWORD

PRIVACY MASK SETTING

PASSWORD LOCK OFF ‚

PASSWORD CHANGE SET ‚

MASK SET SET ‚

PASSWORD CHANGE SET ‚

MASK SET SET ‚

¤¤¤¤

SET ‚

1234

SET ‚

BACK

1 ^{Use the cursor button (j or l) to move the cursor to}

OFF for PASSWORD LOCK in the PRIVACY MASK

SETTING screen. Then press the SET button.

3 ^{Use the same steps to enter “2,” “3,” and “4,” then press}

the SET button.

“OK” will appear and BACK for MENU will be blinking. Press

the SET button again. The PRIVACY MASK SETTING screen

will reappear and “ON” will be blinking for PASSWORD LOCK.

The PASSWORD screen will appear.

2 ^{Enter the factory set password “1234”.}

Use the cursor button (j or l) to select “1”, then use

Note: If a different password is required, “NG” will appear.

Please carefully maintain the password so that it will not be

forgotten.

the cursor button (c).

To move the cursor to the next “*” digit.

1¤¤¤

Download from Www.Somanuals.com. All Manuals Search And Download.

PRIVACY MASK SETTING (PRIVACY MASK)

PASSWORD LOCK cancellation

PASSWORD changes

For use when PASSWORD LOCK is ON

You can change the password with PASSWORD LOCK in either

the ON or OFF setting.

PASSWORD

PRIVACY MASK SETTING

PASSWORD LOCK ON

PASSWORD

‚

PASSWORD CHANGE SET ‚

MASK SET SET ‚

(NOW PASSWORD)

¤¤¤¤

SET ‚

BACK

1234

SET ‚

1234

SET ‚

PASSWORD

PRIVACY MASK SETTING

PASSWORD LOCK OFF ‚

PASSWORD CHANGE SET ‚

MASK SET SET ‚

(NOW PASSWORD)

**** SET ‚

(NEW PASSWORD)

****

SET ‚

1 ^{Press the SET button.}

1 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

SET for PASSWORD CHANGE and press the SET button.

The PASSWORD screen will appear.

The PASSWORD (NOW PASSWORD) screen will appear.

2 ^{Enter the factory set password “1234”.}

2 ^{Use the cursor button (}^d^or^c^,^j^{) to enter the current}

Use the cursor button (j or l) to select “1”, then use

password (Ex: 1234), then press the SET button.

the cursor button (c).

The PASSWORD (NEW PASSWORD) screen will appear.

To move the cursor to the next “*” digit.

3 ^{Use the cursor button (}^d^or^c^,^j^{) to enter a new}

3 ^{Use the same steps to enter “2,” “3,” and “4,” then press}

password (Ex: 4321), then press the SET button.

the SET button.

“OK” will appear and BACK for MENU will be blinking. Press

the SET button again.

The PRIVACY MASK SETTING screen will reappear.

“OK” will appear and BACK for MENU will be blinking. Press

the SET button again. The PRIVACY MASK SETTING screen

will reappear and “OFF” will be blinking for PASSWORD LOCK.

Download from Www.Somanuals.com. All Manuals Search And Download.

LENS SETTING (LENS)

This item allows adjustment of focus (for manual focus or autofocus) and adjustment of zoom when needed.

FOCUS setting

ꢀ Setting the manual focus (MANU)

Sets a limit for near distance focusing and sets focus speed for manual focus.

FOCUS SETTING

MAIN MENU

FOCUS SETTING

LIMIT NEAR

SPEED

LIMIT NEAR

LANGUAGE

CAMERA ID

SYNC

PRIVACY MASK

LENS

SET

OFF

INT

SET

‚

LIMIT NEAR

SPEED

‚

LENS

FOCUS

PRESET

OFF

BACK

PRESET

OFF

BACK

PRESET

OFF

BACK

MANU ‚

SET

ZOOM

‚

1 ^{Use the cursor button (}^j^or^l^{) to select SET for LENS,}

4 ^{SPEED of focus setting}

then press the SET button.

Use the cursor button (j or l) to move the cursor to

SPEED, then use the cursor button (d or c) to select the

focus adjustment speed value. (Ex: 3)

The LENS screen will appear.

2 ^{Use the cursor button (}^d^or^c^{) to select MANU, then}

Available settings: 1, 2, 3, 4 (Quickest speed)

press the SET button.

The FOCUS SETTING screen will appear.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

3 ^{LIMIT NEAR focus distance setting}

Use the cursor button (j or l) to move the cursor to

LIMIT NEAR, then use the cursor button (d or c) to

change the distance value. (Ex: 3M)

Available settings: 1M (meter), 3M, 5M, 10C (centimeters),

30C, 50C

Note: Focusing becomes difficult when near distance limit is set

to less than “1M”.

Download from Www.Somanuals.com. All Manuals Search And Download.

LENS SETTING (LENS)

ꢀ Setting the autofocus (AUTO)

Sets a limit for near distance focusing and sets focusing sensitivity and focus iris.

Note: As a normal practice, use manual focus when keeping the camera focused on the same target object for a long period of time

(over 24 hours). This can be used with the one-push autofocus function when needed (operated from the system controller). Long

periods of surveillance with the autofocus in operation will shorten the work life of the lens.

MAIN MENU

LENS

FOCUS SETTING

LANGUAGE

CAMERA ID

SYNC

PRIVACY MASK

LENS

SET

OFF

INT

SET

OFF

SET

OFF

END

‚

LIMIT NEAR

SENSITIVITY

AREA

HIGH

SET

FOCUS

ZOOM

AUTO ‚

LIMIT NEAR

SENSITIVITY

AREA

LOW

SET

‚

SET

‚

MIRROR

FOCUS SETTING

VIEW SETTING

OPTION

‚

LIMIT NEAR

SENSITIVITY

AREA

PRESET

OFF

BACK

PRESET

OFF

BACK

HIGH

SET

‚

1 ^{Use the cursor button (j or l) to select SET for LENS,}

4 ^{Setting focus SENSITIVITY}

then press the SET button.

Use the cursor button (j or l) to move the cursor to

SENSITIVITY, then use the cursor button (d or c) to

change the setting. (Ex: LOW)

The LENS screen will appear.

2 ^{Use the cursor button (d or c) to select AUTO, then}

Available settings:

press the SET button.

• HIGH: High sensitivity focusing

• LOW: Low sensitivity focusing

The FOCUS SETTING screen will appear.

3 ^{LIMIT NEAR focus distance setting}

Note: When focus SENSITIVITY is set to HIGH, it may react to

even slight movements of the target object. In this case,

change the setting to LOW.

Use the cursor button (j or l) to move the cursor to

LIMIT NEAR, then use the cursor button (d or c) to

change the distance value. (Ex: 3M)

Available settings: 1M (meter), 3M, 5M, 10C (centimeters),

30C, 50C

Note: Focusing becomes difficult when near distance limit is set

to less than “1M”.

Download from Www.Somanuals.com. All Manuals Search And Download.

LENS SETTING (LENS)

FOCUS SETTING

AREA SETTING

LIMIT NEAR

LOW

SET

AREA

SENSITIVITY

AREA

‚

PRESET

OFF

BACK

PRESET

OFF

BACK

PRESET

OFF

BACK

5 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

6 ^{Use the cursor button (}^d^or^c^{) to select the focus target}

SET for AREA, and press the SET button.

area. (Ex: 3)

The AREA SETTING screen for AREA 2 (initial setting) will

appear to allow setting of focus target area.

The focus target area will become narrow.

Available settings: 1/full screen, 2/center of screen,

3/smaller center

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

Download from Www.Somanuals.com. All Manuals Search And Download.

LENS SETTING (LENS)

ZOOM setting

Sets zooming speed and magnification power of the electronic zoom. This item also has a setting for improvement of vertical resolution of

still pictures.

ZOOM SETTING

SPEED 4

MAIN MENU

LENS

SPEED

LANGUAGE

CAMERA ID

SYNC

SET

OFF

INT

SET

OFF

SET

OFF

END

‚

FOCUS

ZOOM

MANU ‚

EL ZOOM

OFF

EL ZOOM

V-RESO.UP

OFF

SET

‚

PRIVACY MASK

LENS

‚

MIRROR

VIEW SETTING

OPTION

‚

PRESET

OFF

BACK

PRESET

OFF

BACK

PRESET

OFF

BACK

3 ^{Zoom speed setting}

1 ^{Use the cursor button (}^j^or^l^{) to select SET for LENS,}

then press the SET button.

Use the cursor button (d or c) to select the zooming

speed. (Ex: 4)

The LENS screen will appear.

Available settings: 1, 2, 3, 4 (Quickest speed)

2 ^{Use the cursor button (}^j^or^l^{) to select SET for ZOOM,}

then press the SET button.

4 ^{EL ZOOM (Electronic zoom) magnification setting}

The ZOOM SETTING screen will appear.

Use the cursor button (j or l) to move the cursor to EL

ZOOM, then use the cursor button (d or c) to select the

electronic zoom magnification power. (Ex: x4)

Available settings: OFF, x2, x4, x8, x16 (16 power)

Download from Www.Somanuals.com. All Manuals Search And Download.

LENS SETTING (LENS)

MIRROR SETTING

ZOOM SETTING

MAIN MENU

SPEED

LANGUAGE

CAMERA ID

SYNC

SET

OFF

INT

SET

OFF

SET

OFF

END

‚

EL ZOOM

V-RESO.UP

PRIVACY MASK

LENS

‚

MIRROR

VIEW SETTING

OPTION

‚

PRESET

OFF

BACK

PRESET

5 ^{V-RESO.UP (Vertical resolution) setting}

1 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

MIRROR, then use the cursor button (d or c) to select

the mirror image effect (Ex: H).

Use the cursor button (j or l) to move the cursor to

V-RESO.UP, then use the cursor button (d or c) to

select the vertical resolution. (Ex: ON)

The image will be inverted horizontally. The image will change

as described below each time the cursor button is pressed.

Note: When V-RESO.UP is set to “ON”, vertical resolution

sensitivity for still pictures in the electronic zoom field will

be improved but afterimages of moving objects will be

more conspicuous.

• OFF: Normal image

• V: Inverted vertically

• H: Inverted horizontally • HV: Inverted horizontally and

vertically

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

OFF

Note:

V-RESO. UP will be automatically set to OFF when any of the

following settings is made.

2 ^{To return to the normal screen, use the cursor button}

(l) to select END at the bottom of the screen, then press

the SET button.

• IRIS: AUTO item SENSE UP (activated)

• SHUTTER: LONG

• AGC: DNR (ON)

Download from Www.Somanuals.com. All Manuals Search And Download.

VIEW SETTING ITEM FLOW

A IRIS setting (See p24)

MAIN MENU

This setting allows selection of IRIS to either autoiris (AUTO) or manual iris (MANU). Initial setting is

autoiris.

LANGUAGE

CAMERA ID

SYNC

SET

OFF

INT

SET

OFF

SET

OFF

END

‚

PRIVACY MASK

LENS

‚

B WHITE BALANCE adjustment (See p31)

MIRROR

This selects the white balance method to be used. Three white balance methods are available: auto

trace white balance (ATW), one-push automatic white balance (AWC), and manual white balance

(MWB). Default setting is auto trace white balance.

VIEW SETTING

OPTION

‚

PRESET

C Electronic SHUTTER setting (See p35)

VIEW SETTING 1

ꢀ

This setting chooses either a fast shutter speed (SHORT) for target objects that may be moving quickly

or a slower shutter speed (LONG) for darker target objects.

IRIS

AUTO ‚

WHITE BALANCE

SHUTTER

MOTION

APERTURE

AGC

ATW

OFF

‚

D MOTION detector setting (See p37)

GAMMA

This function generates an alarm when a suspicious figure is detected. Each of the settings will enable

certain kinds of detection based on the natural image (swaying trees, flickers of light, etc.). It is also

possible to enable zooming in on target objects and intruders that have unusual brightness levels

(moving, bright) or are fast-moving.

PRESET

OFF

BACK

E Profile compensation setting (APERTURE) (See p43)

This setting emphasizes the target object profile (horizontally or vertically).

ꢀ Signifies that VIEW

SETTING 1 is the camera

setting 1. The cursor

button can be used (d or

c) to select one of the

nine VIEW SETTING

patterns (0 – 8).

F Automatic Gain Control (AGC) setting (See p44)

This sets the gain of the AGC circuit. When a target object is dark, the gain changes and the object

becomes lighter.

G GAMMA correction setting (See p45)

This setting enables contrast sensitivity to be boosted by controlling the gamma characteristics. Three

gamma controls are available: gamma correction (ON), smart gamma correction 1 (SMART 1), and

smart gamma correction 2 (SMART 2). Initial setting is ON.

Download from Www.Somanuals.com. All Manuals Search And Download.

VIEW SETTING ITEM FLOW

(About creating image setting files in VIEW SETTING)

Note: When each of the following functions is ON (shown by

single circle), it may be possible to use other functions in

conjunction with it (shown by double circle). View columns

vertically to determine which functions can be used

together.

You can set 9 different patterns with view files. Use the cursor

button (d or c) to change the file number (1) for VIEW SETTING

and press the SET button. The selected image setting file will

appear. Neither the mask function nor the motion detector

function can be used with image setting file “0”, so they will not

appear as options in the screen for pattern 0.

IRIS

AUTO: SENSE UP (activated)

MANU: EI (ON)

MAIN MENU

VIEW SETTING 1

IRIS AUTO ‚

SHUTTER LONG

SHORT

LANGUAGE

CAMERA ID

SYNC

PRIVACY MASK

LENS

SET

OFF

INT

SET

OFF

SET

OFF

END

‚

WHITE BALANCE

SHUTTER

MOTION

ATW

‚

LONG ‚

OFF

‚

APERTURE

AGC

‚

MOTION

MIRROR

VIEW SETTING

OPTION

‚

GAMMA

F: Function is set T: Not allowable E: Allowable

PRESET

OFF

BACK

(Screen for image setting 1 – 8)

VIEW SETTING 0

IRIS

AUTO ‚

WHITE BALANCE

SHUTTER

MOTION

APERTURE

AGC

ATW

‚

LONG ‚

---

‚

GAMMA

PRESET

OFF

BACK

(Screen for image setting 0)

Download from Www.Somanuals.com. All Manuals Search And Download.

VIEW SETTING

A IRIS setting

There are 2 possible settings for IRIS, autoiris (AUTO) and manual iris (MANU).

Autoiris setting (AUTO)

Sets backlight compensation, magnification of electronic

sensitivity and iris level.

VIEW SETTING 1

IRIS

AUTO ‚

ATW

LONG ‚

WHITE BALANCE

SHUTTER

MOTION

APERTURE

AGC

‚

OFF

‚

GAMMA

PRESET

OFF

BACK

1 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

2 ^{Press the SET button.}

VIEW SETTING, then press the SET button. (Ex: 1)

The IRIS SETTING screen will appear.

The VIEW SETTING 1 screen will appear and AUTO for IRIS will

be blinking.

Available settings:

• AUTO: Sets automatic adjustment of iris.

• MANU: Sets manual adjustment of iris.

Note: When AUTO is selected, the following 3 types of detailed

backlight compensation settings will be available.

• Multi-spot evaluative metering (MULT)

• 5 spot centerweighted average metering (CENT)

• 48 multi-spot metering (MASK)

Download from Www.Somanuals.com. All Manuals Search And Download.

VIEW SETTING

Backlight compensation additional settings 1

• Multi-spot evaluative metering (MULT)

IRIS SETTING

BLC SETTING

BLC

SENSE UP

MULT ‚

OFF

(BLC WEIGHT)

í------ú------ü

(LEVEL)

í-----ú+------ü 40

(BRIGHT)

í------ú------ü

1 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

3 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

BRIGHT, and then use the cursor button (d or c) to

select the compensation level.

BLC, then use the cursor button (d or c) to select a

backlight compensation method. (Ex: MULT) Then press

the SET button.

Available settings: 0 – 15

The BLC SETTING screen will appear.

Note: When the number becomes larger, it brightens, and the

compensation level can be set for the brightness of the

backlighting.

Available settings:

• MULT (Multi-spot evaluative metering): Evaluates the entire

screen and corrects according to the best image obtained.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

• CENT (5 spot centerweighted average metering): Measures

light mainly at the center and corrects according to the best

image obtained. (See p26)

Note: When using multi-spot evaluative metering, the

background behind the target object will become very

dark. If a target image in the center of the image is too

bright while using the multi-spot evaluative metering

mode, switch to the 5 spot centerweighted average

metering mode.

• MASK (48 multi-spot metering): Covers bright areas such as

persons with mask patterns and treats light measurement

output as irrelevant. (See p28)

2 ^{Use the cursor button (}^d^or^c^{) to select the value of}

BLC WEIGHT. (Sets backlight and brightness level.)

Available settings: 0 – 15

Note: The larger the number, the more backlighting works.

Download from Www.Somanuals.com. All Manuals Search And Download.

VIEW SETTING

Backlight compensation additional settings 2

• 5 spot centerweighted average metering (CENT)

IRIS SETTING

BLC SETTING

(POSITION)

BLC SETTING

(SIZE)

BLC

SENSE UP

CENT ‚

OFF

(LEVEL)

í-----ú+------ü 40

PRESET

OFF

BACK

1 ^{Use the cursor button (}^d^or^c^{) to select CENT, then}

4 ^{Use the cursor button (}^{j l d c}^{) to adjust the size of}

press the SET button.

the central light sensing zone.

The BLC SETTING (POSITION) screen will appear.

5 ^{Press the SET button.}

2 ^{Use the cursor button (}^{j l d c}^{) to shift the position}

The BLC WINDOW WEIGHTING screen will appear.

of the central light sensing zone.

The zone can be moved up or down and left or right.

Note:

• If the zone fills the right side it will become smaller.

• If the zone fills the bottom side it will become smaller.

3 ^{Press the SET button.}

The BLC SETTING (SIZE) screen will appear.

Download from Www.Somanuals.com. All Manuals Search And Download.

VIEW SETTING

Example of setting the mask in the center weighting position.

BLC WINDOW WEIGHTING

TOP

BOTTOM

LEFT

BOTTOM

LEFT

BOTTOM

LEFT

BOTTOM

LEFT

RIGHT

CENTER(FIX)

RIGHT

CENTER(FIX)

RIGHT

CENTER(FIX)

RIGHT

CENTER(FIX)

PRESET

OFF

BACK

PRESET

OFF

BACK

PRESET

OFF

BACK

PRESET

OFF

BACK

1 TOP: Weighting is at top.

2 BOTTOM: Weighting is at bottom.

3 LEFT: Weighting is at left.

4 RIGHT: Weighting is at right.

5 CENT (FIX): Center weighting is fixed by the number 7.

BLC WINDOW WEIGHTING

TOP

BOTTOM

LEFT

RIGHT

CENTER(FIX)

PRESET

OFF

BACK

6 ^{Use the cursor button (j or l) to select a zone, then}

use the cursor button (d or c) to adjust weighting.

Each setting will change as shown in the illustration.

The area from each of the zones 0 – 7, except CENTER, can

be adjusted.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

Download from Www.Somanuals.com. All Manuals Search And Download.

VIEW SETTING

Backlight compensation additional settings 3

• 48 multi-spot metering (MASK)

IRIS SETTING

BLC MASKING

BLC

SENSE UP

MASK ‚

OFF

(LEVEL)

í-----ú+------ü 40

CONTINUE (ñ)

PRESET

OFF

BACK

1 ^{Use the cursor button (}^d^or^c^{) to select MASK, then}

3 ^{Finishing mask pattern setting}

press the SET button.

Use the cursor button (j or l) to move a mask pattern to

the bottom area of the screen and continue holding it for 3

seconds. The PRESET and MENU items will appear on the

screen.

The BLC MASKING screen will appear and the mask pattern

will be blinking.

2 ^{Use the cursor button (}^{j l d c}^{) to move the cursor to}

move the mask pattern over the area not to be sensed,

then press the SET button.

• Use the cursor button (l) to select BACK for MENU and

press the SET button. The IRIS SETTING screen will

reappear.

The mask pattern will be set. You can use the same steps to

set additional mask patterns.

• Use the cursor button (l) to move the cursor to BACK for

MENU, use the cursor button (d or c) to select END, and

then press the SET button. The normal screen will reappear.

Note: The initial mask pattern is at the upper left of the screen,

and it is not set. To clear a mask pattern after it is set,

press the SET button again.

Download from Www.Somanuals.com. All Manuals Search And Download.

VIEW SETTING

SENSE UP setting

LEVEL setting

IRIS SETTING

MULT

IRIS SETTING

BLC

SENSE UP

MULT

BLC

SENSE UP

(LEVEL)

í----ú-+------ü 40

(LEVEL)

í-----ú+------ü 40

PRESET

OFF

BACK

PRESET

OFF

BACK

Use the cursor button (j or l) to move the cursor to

LEVEL, then use the cursor button (d or c) to adjust the iris

level.

Use the cursor button (j or l) to move the cursor to

SENSE UP, then use the cursor button (d or c) to select the

power of the electronic sensitivity. (Ex: x4)

Available settings: 0 – 100

Available settings: OFF, x2, x4, x8, x16, x32

Note: The larger the number, the more it brightens.

Note:

• Electronic sensitivity boosting (SENSE UP) automatically

lengthens the CCD exposure time in dark situations.

Accordingly, do not use for light target objects. Because

exposure time is lengthened while in operation, moving target

objects may cause conspicuous afterimages and blurs.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

• It is not possible to set SENSE UP (activated) or SHUTTER

(LONG) when MOTION is set to “ON”.

• When SENSE UP is activated for IRIS SETTING, the electronic

shutter cannot be forcibly moved.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

Download from Www.Somanuals.com. All Manuals Search And Download.

VIEW SETTING

Manual iris setting

Sets electronic iris ON/OFF, lens aperture and iris level.

MAIN MENU

VIEW SETTING 1

IRIS SETTING

LANGUAGE

CAMERA ID

SYNC

PRIVACY MASK

LENS

SET

OFF

INT

SET

OFF

‚

IRIS

MANU ‚

WHITE BALANCE

SHUTTER

MOTION

APERTURE

AGC

ATW

‚

LONG ‚

OFF

(IRIS STOP)

í------+------ú 17

(IRIS STOP)

í------+------ú 17

‚

MIRROR

(LEVEL)

í----ú-+------ü 40

(LEVEL)

í----ú-+------ü 40

VIEW SETTING

OPTION

‚

GAMMA

SET

1 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

5 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

LEVEL, then use the cursor button (d or c) to select the

value.

VIEW SETTING, then press the SET button. (Ex: 1)

The VIEW SETTING 1 screen will appear.

Available settings: 0 – 100 (Level of opening)

2 ^{Use the cursor button (}^d^or^c^{) to select MANU, then}

press the SET button.

Note:

The IRIS SETTING screen will appear.

• The smaller the value the more the video level drops,

becoming darker.

3 ^{Electronic IRIS setting}

• The LEVEL setting controls both AGC circuit gain and shutter

speed, changing the amount of exposure.

Use the cursor button (d or c) to select El. (Ex: ON)

Note: When SENSE UP is activated for IRIS SETTING, the

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

electronic shutter cannot be forcibly moved.

4 ^{Lens aperture setting}

Use the cursor button (j or l) to move the cursor to IRIS

Note:

STOP, then use the cursor button (d or c) to select the value.

• If the iris views an unusually bright image, it can cause a

smear that cannot be corrected by adjusting the light entering

through the lens. In this case, arrange the physical angle of

lighting in a way that will prevent on-screen smearing.

Available settings: 1 – 17 (Aperture opening)

Note:

• The smaller the value the more the aperture closes and the

image darkens.

• If flickering of the target object occurs because of florescent

lighting in the camera location, changing to incandescent

lighting will prevent the flickering.

• Changes to the value directly control the aperture of the lens.

Download from Www.Somanuals.com. All Manuals Search And Download.

VIEW SETTING

B WHITE BALANCE adjustment

Adjustments can be made to 3 methods of white balance correction: Auto trace white balance (ATW), one-push automatic white balance

(AWC), and manual white balance (MWB).

MAIN MENU

VIEW SETTING 1

IRIS AUTO ‚

LANGUAGE

CAMERA ID

SYNC

SET

OFF

INT

SET

OFF

SET

OFF

END

‚

WHITE BALANCE

SHUTTER

MOTION

MWB

‚

LONG ‚

OFF

PRIVACY MASK

LENS

‚

APERTURE

AGC

‚

MIRROR

VIEW SETTING

OPTION

‚

GAMMA

PRESET

OFF

BACK

The following methods are available for white balance correction.

See the corresponding reference sections for additional setting

options.

1 ^{Use the cursor button (j or l) to move the cursor to}

VIEW SETTING, then press the SET button. (Ex: 1)

The VIEW SETTING 1 screen will appear.

Available methods:

2 ^{Use the cursor button (j or l) to move the cursor to}

WHITE BALANCE, then use the cursor button (d or c)

to select a white balance type “MWB”. Then press the

SET button.

ATW (Auto trace white balance)

Even when light sources change, automatic adjustment assures

capture of most suitable colors. When a bright light source

prevents effective white balance, a mask can be placed over the

light source. (See p32)

The MWB SETTING screen will appear.

AWC (One-push automatic white balance)

White balance is adjusted automatically with one-push activation.

AWC is usually set for white target objects (walls, paper, etc.) that

do not return color faithfully in the ATW method. (See p34)

MWB (Manual white balance)

Fine adjustments for preferred colors can be done manually. This

method is preferable when suitable colors cannot be obtained

with the ATW method. (See p32)

Download from Www.Somanuals.com. All Manuals Search And Download.

VIEW SETTING

White balance additional settings 1

MWB setting

White balance additional settings 2

ATW setting

Automatic white balance settings are completed when ATW is

selected. However, white balance will not be suitably adjusted if a

bright light source or an excessively dark area from the

environment is in the image. In this case, the bright light source or

dark area should be masked so that it will not be detected.

VIEW SETTING 1

MWB SETTING

(OFFSET)

IRIS

AUTO ‚

WHITE BALANCE

SHUTTER

MOTION

APERTURE

AGC

MWB

‚

LONG ‚

OFF

R í---ú--+------ü 70

B í---ú--+------ü 66

‚

GAMMA

VIEW SETTING 1

IRIS AUTO ‚

ATW SETTING

1 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

WHITE BALANCE, then use the cursor button (d or c)

to select a white balance type (Ex: MWB). Then press the

SET button.

MASKING

SMART ATW

‚

WHITE BALANCE

SHUTTER

MOTION

ATW

‚

LONG ‚

OFF

‚

APERTURE

AGC

GAMMA

The MWB SETTING screen will appear.

1 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

2 ^{Use the cursor button (}^d^or^c^{) to adjust the value for}

ATW for WHITE BALANCE and press the SET button.

“R” (red).

The ATW SETTING screen will appear.

Available settings: 0 – 255

2 ^{Use the cursor button (}^d^or^c^{) to select ON for}

Note: The larger the number, the stronger red becomes.

MASKING, then press the SET button.

3 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

“B”, then use the cursor button (d or c) to adjust the

“Blue” value.

The ATW MASKING screen will appear with the mask pattern

blinking in the upper left corner of the screen.

Available settings: 0 – 255

Note: The larger the number, the stronger blue becomes.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

Download from Www.Somanuals.com. All Manuals Search And Download.

VIEW SETTING

ATW MASKING

ATW SETTING

MASKING

‚

MASKING

‚

SMART ATW

OFF

SMART ATW

CONTINUE (ñ)

PRESET

OFF

BACK

PRESET

OFF

BACK

ꢀ SMART ATW setting

If saturation is high or a scene is bright, the most suitable colors

may not be obtained. In this case, set the SMART ATW to ON.

3 ^{Use the cursor button (}^{j l d c}^{) to move the mask}

pattern over the bright light source, then press the SET

button.

Use the same steps to place addition masks as needed.

5 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

SMART ATW, then use the cursor button (d or c) to set

ON.

Note: Initial settings place no masks on the screen. To cancel the

placement of masks, press the SET button again.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

4 ^{Use the cursor button (}^j^or^l^{) to move a mask pattern}

to the bottom area of the screen and continue holding

the cursor button straight down for 3 seconds.

The PRESET and MENU items will appear on the screen. Use

the cursor button (j or l) to select BACK, then press the

SET button. The ATW SETTING screen will reappear.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

Download from Www.Somanuals.com. All Manuals Search And Download.

VIEW SETTING

White balance additional settings 3

AWC setting

VIEW SETTING 1

AWC SETTING

MWB SETTING

(OFFSET)

IRIS

AUTO ‚

AWC

LONG ‚

AWC LOCK

GO TO MWB

SET

AWC LOCK

GO TO MWB

SET

WHITE BALANCE

SHUTTER

MOTION

APERTURE

AGC

‚

R í---ú--+------ü 70

B í---ú--+------ü 66

OFF

‚

GAMMA

1 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

3 ^{GO TO MWB setting}

AWC for WHITE BALANCE and press the SET button.

Use the cursor button (j or l) to move the cursor to

The AWC SETTING screen will appear.

SET for GO TO MWB and press the SET button.

The MWB SETTING screen will appear and the “R” value will

be blinking.

2 ^{With SET blinking for AWC LOCK, press the SET button.}

SET will light and adjustment of white balance will begin. After

about 3 seconds, SET will begin blinking again, signaling that

adjustment is complete.

4 ^{Use the cursor button (}^d^or^c^{) to adjust the value for}

“R” (red).

Available settings: 0 – 255

Note:

Note: The larger the number, the stronger red becomes.

For even finer adjustment of coloration, choose SET for GO TO

MWB. White balance mode will become MWB for fine

adjustment. After fine adjustment with GO TO MWB, the white

balance mode will automatically switch to MWB.

5 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

“B”, then use the cursor button (d or c) to adjust the

“Blue” value.

Note: Full adjustment may not be possible with just one

activation of SET for AWC LOCK. In that case, press the

SET button again.

Available settings: 0 – 255

Note: The larger the number, the stronger blue becomes.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

Download from Www.Somanuals.com. All Manuals Search And Download.

VIEW SETTING

C Electronic SHUTTER setting

Sets the electronic shutter to either the fast shutter speed mode (SHORT) or the slow shutter speed mode (LONG).

Fast shutter speed (SHORT) mode setting

MAIN MENU

VIEW SETTING 1

IRIS AUTO ‚

ES SETTING

LANGUAGE

CAMERA ID

SYNC

SET

OFF

INT

SET

OFF

SET

OFF

END

‚

SHUTTER SPEED

WHITE BALANCE

SHUTTER

MOTION

ATW

‚

SHORT‚

OFF

PRIVACY MASK

LENS

‚

APERTURE

AGC

‚

MIRROR

OFF

VIEW SETTING

OPTION

‚

GAMMA

PRESET

OFF

BACK

PRESET

OFF

BACK

1 ^{Use the cursor button (j or l) to move the cursor to}

3 ^{Use the cursor button (d or c) to select a electronic}

VIEW SETTING, then press the SET button. (Ex: 1)

shutter speed.

The VIEW SETTING 1 screen will appear.

Available settings: 50, 120, 250, 500, 1000, 2000, 4000,

10000

2 ^{Use the cursor button (j or l) to move the cursor to}

SHUTTER, then use the cursor button (d or c) to select

the speed mode for the electronic shutter. (Ex: SHORT)

Then press the SET button.

Note: SHORT mode cannot be set if SENSE UP is activated or IRIS

is “ON”.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

The ES SETTING screen will appear and 50 (1/50 sec) will be

blinking. This setting is suitable for fast moving target objects.

Download from Www.Somanuals.com. All Manuals Search And Download.

VIEW SETTING

Slow shutter speed (LONG) mode setting

VIEW SETTING 1

ES SETTING

IRIS

AUTO ‚

SHUTTER SPEED

WHITE BALANCE

SHUTTER

MOTION

APERTURE

AGC

ATW

‚

LONG ‚

OFF

‚

GAMMA

PRESET

OFF

BACK

PRESET

OFF

BACK

Note:

1 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

SHUTTER, then use the cursor button (d or c) to select

the speed mode for the electronic shutter. (Ex: LONG)

Then press the SET button.

SHUTTER (LONG) cannot be set if any of the following settings is

active.

• MOTION: ON

The ES SETTING screen will appear and x1 (1/50 sec) will be

blinking. This setting is suitable for dark target objects.

• IRIS: AUTO item SENSE UP (activated) or MANU item El

(ON)

Note: When a shutter speed is set, it can also be adjusted with

the “ELS” button on the system controller.

2 ^{Use the cursor button (}^d^or^c^{) to select a electronic}

shutter speed.

Available settings: x1, x2, x4, x8, x16, x32 (Field times

shown as multiples.)

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

Download from Www.Somanuals.com. All Manuals Search And Download.

VIEW SETTING

D MOTION detector setting

This function divides the monitor screen into 48 zones (8 x 6). Based on information from the separate zones, target images that show

intruder movements are detected and an alarm is generated. The degree of motion to be detected can be finely set.

Note:

• Before activating this setting, use the cursor button to select a surveillance location that will not detect motion.

• When SHUTTER speed is in LONG mode and IRIS SETTING has SENSE UP activated, the MOTION function cannot be turned ON.

MAIN MENU

VIEW SETTING 1

IRIS

MOTION SETTING

MOTION SIZE

LANGUAGE

CAMERA ID

SYNC

SET

OFF

INT

SET

OFF

SET

OFF

END

‚

AUTO ‚

SIZE

SET

‚

WHITE BALANCE

SHUTTER

MOTION

ATW

OFF

‚

MASKING

SENSITIVITY

ZOOM

SET

OFF

PRIVACY MASK

LENS

‚

APERTURE

AGC

INTERVAL

ALARM SIGN

MIRROR

OFF

VIEW SETTING

OPTION

‚

GAMMA

PRESET

OFF

BACK

PRESET

OFF

BACK

PRESET

OFF

BACK

1 ^{Use the cursor button (j or l) to move the cursor to}

3 ^{MOTION SIZE setting}

VIEW SETTING, then press the SET button. (Ex: 1)

Sets the target object size desired for detection in the 48 zone

screen.

The VIEW SETTING 1 screen will appear.

2 ^{Use the cursor button (j or l) to move the cursor to}

MOTION, and then use the cursor button (d or c) to

select ON. Then press the SET button.

Press the SET button again.

The MOTION SIZE screen appears and the “1” for “V” will be

blinking.

The MOTION SETTING screen will appear and SET for SIZE will

be blinking.

Download from Www.Somanuals.com. All Manuals Search And Download.

VIEW SETTING

MOTION SIZE

4 ^{Set the size of the target object desired for detection}

1 Determine the vertical size

Tilt the cursor button to the right (c).

PRESET

OFF

PRESET

OFF

PRESET

OFF

BACK

The “V” value (vertical pattern) will change to “2” and the

detection pattern will expand downward. Repeating this

motion will expand the pattern in the up and down

direction. Tilting the cursor button to the left will reduce

the pattern size.

V1, H1

V2, H1

V6, H1

MOTION SIZE

2 Determine the horizontal size

PRESET

OFF

PRESET

OFF

PRESET

OFF

Use the cursor button (l) to move the cursor to the

“1” for “H”, then tilt the cursor button to the right

(c).

BACK

V2, H2

V2, H3

V3, H3

MOTION SIZE

The “H” value (horizontal pattern) will change to “2” and the

detection pattern will expand to the left. Repeating this

motion will expand the pattern in the left and right direction.

Tilting the cursor button to the left will reduce the pattern

size.

PRESET

OFF

BACK

PRESET

OFF

BACK

PRESET

OFF

BACK

V1, H2

V1, H3

V1, H8

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

Download from Www.Somanuals.com. All Manuals Search And Download.

VIEW SETTING

MOTION MASKING setting

Masking target objects that are not desired for detection (swaying trees, flickers of light , etc.) will prevent unwanted alarms from being

generated. This is done in the MOTION SETTING screen.

MOTION SETTING

MOTION MASKING

SIZE

SET

‚

MASKING

SENSITIVITY

ZOOM

SET

OFF

INTERVAL

ALARM SIGN

OFF

CONTINUE (ñ)

PRESET

OFF

BACK

1 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

MASKING, and then use the cursor button (d or c) to

select ON. Then press the SET button.

3 ^{Finishing motion pattern setting}

Use the cursor button (j or l) to move a mask pattern to

the bottom area of the screen and continue holding it for 3

seconds. The PRESET and MENU items will appear on the

screen.

The MOTION MASKING screen will appear, and the mask

pattern will be blinking in the upper left corner of the screen.

2 ^{Use the cursor button (}^{j l d c}^{) to move the mask}

pattern to the target object that is not to be detected,

then press the SET button.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

Repeat these steps to set mask patterns in other locations.

Note: To clear a mask pattern, press the SET button again on

the pattern.

Download from Www.Somanuals.com. All Manuals Search And Download.

VIEW SETTING

Available settings: 1 – 10

SENSITIVITY setting

Set the degree of sensitivity for motion detection corresponding

to MOTION SIZE. Sensitivity can be set so that natural motions on

the screen such as wind and light changes will not be detected.

When this is necessary, activate the following setting.

ꢀ Brightness differences (Y-DIFFER)

Use the cursor button (j or l) to move the cursor to

Y-DIFFER, then use the cursor button (d or c) to adjust the

brightness differences.

Changes in brightness can sometimes be mistakenly detected as

motion. To avoid detection of the turning on and off of lighting,

make the value larger.

MOTION SETTING

SENSITIVITY

í---ú----ü

Y-LEVEL í---ú----ü

Y-DIFFER í---ú----ü

DURATION ú--------ü

SIZE

SET

‚

MOVE

MASKING

SENSITIVITY

ZOOM

INTERVAL

ALARM SIGN

SET

OFF

Available settings: 1 – 10

OFF

DEMO

OFF

ꢀ DURATION setting

Use the cursor button (j or l) to move the cursor to

SENSITIVITY, and then use the cursor button (d or c) to

select SET. Then press the SET button.

Use the cursor button (j or l) to move the cursor to

DURATION, then use the cursor button (d or c) to adjust

the detection time duration.

The SENSITIVITY screen will appear.

To avoid detecting fast movements, make the value larger.

When necessary, adjust the following settings.

Available settings: 1 – 60

ꢀ Motion sensitivity (MOVE) setting

ꢀ Detected motion confirmation mode (DEMO)

Use the cursor button (j or l) to move the cursor to

DEMO, then use the cursor button (d or c) to change ON.

Use the cursor button (j or l) to move the cursor to

MOVE, then use the cursor button (d or c) to adjust the

movement value.

When a motion is detected, patterns are shown in that location.

While the detected motion is being confirmed, the SENSITIVITY

settings are optimized. This mode can only be activated in the

SENSITIVITY setting screen.

To avoid detection of small movements such as wind, make the

value larger.

Available settings: 1 – 10

ꢀ Brightness level (Y-LEVEL)

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

Use the cursor button (j or l) to move the cursor to

Y-LEVEL, then use the cursor button (d or c) to adjust the

brightness level.

When noise from a dark screen is causing erroneous detections,

make the value larger.

Download from Www.Somanuals.com. All Manuals Search And Download.

VIEW SETTING

ZOOM setting

INTERVAL setting

This item is set in the MOTION SETTING screen.

MOTION SETTING

SIZE

SET

‚

SIZE

SET

‚

MASKING

SENSITIVITY

ZOOM

MASKING

SENSITIVITY

ZOOM

SET

OFF

SET

OFF

INTERVAL

ALARM SIGN

INTERVAL

ALARM SIGN

OFF

PRESET

OFF

BACK

PRESET

OFF

BACK

Use the cursor button (j or l) to move the cursor to

INTERVAL, then use the cursor button (d or c) to select the

time interval (Ex.: 15S).

Use the cursor button (j or l) to move the cursor to

ZOOM, then use the cursor button (d or c) to select the

zoom magnification power (Ex.: x2).

Available settings: 5S, 10S, 15S, 20S, 30S, 1M, 2M, 3M, 4M,

Available settings: OFF, x1.4, x2, x2.8, x4, x6

Note:

Note: When a motion is detected, no other motions will be

• When a suspicious motion is detected, the camera zooms in

according to the set magnification power. The zoom takes

effect for 5 seconds and then returns to the previous

magnification level.

detected within the set interval of time.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

• The zoom focuses on the center of the screen. If the

maximum optical performance is exceeded, zooming will stop

at maximum magnification.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

Download from Www.Somanuals.com. All Manuals Search And Download.

VIEW SETTING

ALARM SIGN setting

This item is set in the MOTION SETTING screen.

MOTION SETTING

SIZE

SET

‚

MASKING

SENSITIVITY

ZOOM

SET

OFF

INTERVAL

ALARM SIGN

OFF

PRESET

OFF

BACK

Use the cursor button (j or l) to move the cursor to OFF

for ALARM SIGN, and then use the cursor button (d or c)

to select ON.

Available settings:

• ON: The camera ID display blinks when motion is detected.

• OFF: The camera ID display does not blink when motion is

detected.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

Download from Www.Somanuals.com. All Manuals Search And Download.

VIEW SETTING

E Profile compensation setting (APERTURE)

Set this function to further emphasize the profile of the target object. The amount of compensation can be adjusted for horizontal or

vertical directions.

MAIN MENU

VIEW SETTING 1

IRIS AUTO ‚

APERTURE SETTING

H í------ú------ü

V í------ú------ü

LANGUAGE

CAMERA ID

SYNC

SET

OFF

INT

SET

OFF

SET

OFF

END

‚

WHITE BALANCE

SHUTTER

MOTION

ATW

‚

LONG ‚

PRIVACY MASK

LENS

‚

OFF

‚

APERTURE

AGC

MIRROR

VIEW SETTING

OPTION

‚

GAMMA

PRESET

OFF

BACK

PRESET

OFF

BACK

1 ^{Use the cursor button (j or l) to move the cursor to}

3 ^{Select the amount of profile compensation}

Available settings: 1 – 15 (Compensation intensity)

1 Set the horizontal profile compensation

VIEW SETTING, then press the SET button. (Ex: 1)

The VIEW SETTING 1 screen will appear.

2 ^{Use the cursor button (j or l) to move the cursor to}

APERTURE and then use the cursor button (d or c) to

select ON. Then press the SET button.

Use the cursor button (d or c) to adjust the value for

“H” (horizontal).

2 Set the vertical profile compensation

The APERTURE SETTING screen will appear and the “H” value

will be blinking.

Use the cursor button (j or l) to move the cursor to “V”

(vertical), then use the cursor button (d or c) to adjust

the value for “V”.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

Download from Www.Somanuals.com. All Manuals Search And Download.

VIEW SETTING

F Automatic gain control (AGC) setting

Sets AGC to ON or OFF and adjusts the gain.

(When ON is set)

(When OFF is set)

GAIN SETTING

MAIN MENU

VIEW SETTING 1

GAIN SETTING

LANGUAGE

CAMERA ID

SYNC

SET

OFF

INT

SET

OFF

‚

IRIS

AUTO ‚

MAX GAIN

DNR

0·

WHITE BALANCE

SHUTTER

MOTION

APERTURE

AGC

ATW

‚

LONG ‚

OFF

ú------+------ü 0·

PRIVACY MASK

LENS

‚

MIRROR

VIEW SETTING

‚

GAMMA

Available settings:

1 ^{Use the cursor button (j or l) to move the cursor to}

• ON: DNR (Digital Noise Reduction) is applied. Noise from

VIEW SETTING, then press the SET button. (Ex: 1)

low light will be reduced.

The VIEW SETTING 1 screen will appear.

• OFF: DNR will not be applied.

2 ^{Use the cursor button (j or l) to move the cursor to}

AGC, and then use the cursor button (d or c) to select

Note: Digital noise reduction works as gain control becomes

greater. If images for moving target objects have blurs or

afterimages, reduce the resolution sensitivity.

the compensation level.

Available settings:

• ON: DNR (digital noise reduction) can be set

• OFF: Fixed gain values can be adjusted manually.

ꢀ When OFF is set

1 Use the cursor button (d or c) to select OFF, then press

the SET button.

ꢀ When ON is set

The GAIN SETTING screen will appear, and “0dB” will be

blinking.

Available settings: 0 – 30dB

1 Use the cursor button (d or c) to select ON then press

the SET button.

The GAIN SETTING screen will appear, and “ 0dB” will be

blinking for MAX GAIN.

2 Use the cursor button (d or c) to adjust the gain.

2 Use the cursor button (d or c) to select the gain.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

Available settings: –6dB, 0dB, +6dB, +9dB

3 Use the cursor button (j or l) to move the cursor to

DNR, and then use the cursor button (d or c) to select

ON.

Download from Www.Somanuals.com. All Manuals Search And Download.

VIEW SETTING

G GAMMA correction setting

In addition to turning gamma correction ON or OFF, contrast sensitivity can be boosted at 2 levels.

MAIN MENU

VIEW SETTING 1

IRIS AUTO ‚

LANGUAGE

CAMERA ID

SYNC

SET

OFF

INT

SET

OFF

SET

OFF

END

‚

WHITE BALANCE

SHUTTER

MOTION

ATW

‚

LONG ‚

OFF

PRIVACY MASK

LENS

‚

APERTURE

AGC

‚

MIRROR

VIEW SETTING

OPTION

‚

GAMMA

PRESET

OFF

BACK

1 ^{Use the cursor button (j or l) to move the cursor to}

VIEW SETTING, then press the SET button. (Ex: 1)

The VIEW SETTING 1 screen will appear.

2 ^{Use the cursor button (j or l) to move the cursor to}

ON for GAMMA, then use the cursor button (d or c) to

select the gamma correction.

Available settings:

• OFF: No gamma correction

• ON: Gamma correction (γ = 0.45)

• SMART 1: Correction 1

• SMART 2: Correction 2 (improves contrast for dark

locations)

Note: When using SMART 1 or SMART 2, the target object may

be too bright, so determine which setting is better for the

target object.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPTION SETTING

MAIN MENU

OPTION

RS-485 SETTING

BAUD RATE

RS-485 SETTING

BAUD RATE

LANGUAGE

CAMERA ID

SYNC

SET

OFF

INT

SET

OFF

‚

CONTROL

ADDRESS

ALARM

485

SET

‚

19200

OFF

19200

OFF

TERMINATE

PRIVACY MASK

LENS

‚

MIRROR

VIEW SETTING

OPTION

‚

SET

CONTROL setting

1 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

3 ^{Use the cursor button (}^d^or^c^{) to select 19200 for BAUD}

OPTION, then press the SET button.

RATE.

The OPTION screen will appear.

Available settings: 19200, 9600, 4800, 2400

4 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

TERMINATE, and then use the cursor button (d or c) to

select the terminate setting.

Note: The PRESET ON setting cannot be used when OPTION

settings are in use.

2 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

485 for CONTROL, use the cursor button (d or c) to

select the device to be operated (Ex: 485), and then press

the SET button.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

The RS-485 SETTING screen will appear.

Available settings:

• 485: For operation by the System Controller

• COAX: For operation of device by linked coax cable.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPTION SETTING

ALARM setting

MAIN MENU

OPTION

LANGUAGE

CAMERA ID

SYNC

SET

OFF

INT

SET

OFF

‚

CONTROL

ADDRESS

ALARM

485

SET

‚

A Alarm input setting (ALARM IN)

Make the following settings for alarm detection.

PRIVACY MASK

LENS

‚

MIRROR

Connect the external alarm switch to the alarm input terminal on

the back of the camera.

VIEW SETTING

OPTION

‚

SET

ADDRESS setting

MAIN MENU

OPTION

LANGUAGE

CAMERA ID

SYNC

SET

OFF

INT

SET

OFF

‚

CONTROL

ADDRESS

ALARM

485

SET

‚

1 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

PRIVACY MASK

LENS

‚

OPTION, then press the SET button.

MIRROR

The OPTION screen will appear.

VIEW SETTING

OPTION

‚

SET

Note: The PRESET ON setting cannot be used when OPTION

1 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

settings are in use.

OPTION, then press the SET button.

2 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

ADDRESS, and then use the cursor button (d or c) to

select the address.

The OPTION screen will appear.

Note: The PRESET ON setting cannot be used when OPTION

settings are in use.

Available settings: 0 (d) ~ 127 (c)

2 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

ALARM, then press the SET button.

The ALARM SETTING screen will appear.

3 ^{Use the cursor button (}^d^or^c^{) to select POLARITY}

between “NO” and “NC”.

Available settings:

• NO: Normal open (Normally open so closed condition is

detected as input.)

• NC: Normal closed (Normally closed so open condition is

detected as input.)

Download from Www.Somanuals.com. All Manuals Search And Download.

OPTION SETTING

Alarm duration setting (DURATION)

Set the duration for the following alarm input reception.

ALARM SETTING

ALARM IN

POLARITY

MOTION

OFF

DURATION

ALARM OUT

POLARITY

ALARM TIME

LINE OUT

Use the cursor button (j or l) to move the cursor to

DURATION, then use the cursor button (d or c) to select

the alarm duration.

OFF

Available settings: 5S, 10S, 15S, 20S, 30S, 1M, 2M, 3M, 4M,

Motion sensor input setting (MOTION)

Matches information from the camera’s motion sensor and the

external alarm and outputs it.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

Use the cursor button (j or l) to move the cursor to

MOTION, then use the cursor button (d or c) to select the

input.

Available settings:

• OFF: Does not output a motion sensor alarm.

• AND: Outputs an alarm when an external alarm input and

motion sensor alarm are detected at the same time.

• OR: Outputs an alarm if either an external alarm or a motion

sensor alarm is detected.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPTION SETTING

B Alarm output setting (ALARM OUT)

ALARM SETTING

ALARM IN

POLARITY

MOTION

DURATION

ALARM OUT

POLARITY

ALARM TIME

LINE OUT

ALARM IN

POLARITY

MOTION

DURATION

ALARM OUT

POLARITY

ALARM TIME

LINE OUT

OFF

1 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

ALARM OUT, then use the cursor button (d or c) to

select the “ON” or “ OFF”.

3 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

ALARM TIME, then use the cursor button (d or c) to

select the amount of time for external alarm output.

Available settings:

Available settings: 5S, 10S, 15S, 20S, 30S, 1M, 2M, 3M, 4M,

• ON: Output an alarm (for activation of buzzer or lamp)

• OFF: Does not output an alarm

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

2 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

POLARITY, then use the cursor button (d or c) to select

the “NO” or “NC”.

Available settings:

• NO: Normal open (Normally open so closed condition is

detected as input.)

• NC: Normal closed (Normally closed so open condition is

detected as input.)

Download from Www.Somanuals.com. All Manuals Search And Download.

OPTION SETTING

c Operation of alarm signal output to the System

Controller setting (LINE OUT)

Outputs alarm signal to the System Controller. The ALARM lamp

on the System Controller will blink when it receives an alarm

signal. An alarm list can be displayed to show information such as

date/time alarm was received, the device sending the alarm and

the alarm type.

ALARM SETTING

ALARM IN

POLARITY

MOTION

OFF

DURATION

ALARM OUT

POLARITY

ALARM TIME

LINE OUT

OFF

Use the cursor button (j or l) to move the cursor to LINE

OUT, then use the cursor button (d or c) to select the

“ON” or “ OFF”.

Available settings:

• ON: Outputs alarm signal to the System Controller

• OFF: Does not output alarm signal to the System Controller

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

Download from Www.Somanuals.com. All Manuals Search And Download.

MENU FLOW

LANGUAGE

CAMERA ID SETTING

L-L SETTING

(V SYNC PHASE)

ú------+------ü

LANGUAGE

LANGUE

ENGLISH

FRENCH

GERMANY

ABCDEFGHIJKLM

NOPQRSTUVWXYZ

0123456789 :-‚

SPRACHE

ID ????????????????

POSITION

SET

‚

BACK

MAIN MENU

PRIVACY MASK SETTING

PASSWORD LOCK ON ‚

PASSWORD

LANGUAGE

CAMERA ID

SYNC

SET

OFF

INT

SET

OFF

SET

OFF

END

‚

PASSWORD CHANGE SET ‚

MASK SET SET ‚

(NEW PASSWORD)

PRIVACY MASK

LENS

‚

1234

SET ‚

****

SET ‚

MIRROR

VIEW SETTING

OPTION

‚

PRESET

PASSWORD

BACK

(NOW PASSWORD)

MASK 3 SET

(POSITION)

****

SET ‚

OPTION

MASK NO.SELECT

CONTROL

ADDRESS

ALARM

485

SET

‚

MASK

OFF

SET

‚

OFF

RS-485 SETTING

BAUD RATE

TERMINATE

19200

OFF

LENS

FOCUS SETTING

AREA SETTING

FOCUS

ZOOM

AUTO ‚

LIMIT NEAR

SENSITIVITY

AREA

HIGH

SET

AREA

SET

‚

MANU

ALARM SETTING

VIEW SETTING 1

PRESET

OFF

BACK

ALARM IN

POLARITY

MOTION

DURATION

ALARM OUT

POLARITY

ALARM TIME

LINE OUT

ZOOM SETTING

FOCUS SETTING

LIMIT NEAR 1M

IRIS

AUTO ‚

ATW

LONG ‚

OFF

SPEED

OFF

WHITE BALANCE

SHUTTER

MOTION

APERTURE

AGC

‚

EL ZOOM

V-RESO.UP

SPEED

OFF

‚

OFF

GAMMA

See page 52

PRESET

OFF

BACK

Download from Www.Somanuals.com. All Manuals Search And Download.

MENU FLOW

VIEW SETTING 1

IRIS SETTING

BLC SETTING

(POSITION)

BLC MASKING

IRIS

AUTO ‚

BLC

SENSE UP

OFF

(BLC WEIGHT)

í------ú------ü

WHITE BALANCE

SHUTTER

MOTION

APERTURE

AGC

ATW

‚

LONG ‚

OFF

(LEVEL)

(BRIGHT)

í------ú------ü

‚

í------ú------ü 40

GAMMA

CONTINUE (ñ)

PRESET

OFF

BACK

IRIS SETTING

OFF

(IRIS STOP)

í------ú------ü 17

BLC SETTING

(SIZE)

BLC WINDOW WEIGHTING

(LEVEL)

í------ú------ü 60

TOP

BOTTOM

LEFT

RIGHT

CENTER(FIX)

PRESET

OFF

BACK

GAIN SETTING

ATW SETTING

AWC SETTING

MWB SETTING

(OFFSET)

MAX GAIN

DNR

0·

MASKING

OFF

AWC LOCK

GO TO MWB

SET

OFF

SMART ATW

‚

R í---ú--+------ü 70

B í---ú--+------ü 66

OFF

GAIN SETTING

ES SETTING

SHUTTER SPEED

ú------+------ü 0·

MOTION SETTING

MOTION SIZE

MOTION MASKING

SENSITIVITY

í---ú----ü

Y-LEVEL í---ú----ü

Y-DIFFER í---ú----ü

DURATION ú--------ü

SIZE

SET

OFF

‚

MOVE

MASKING

SENSITIVITY

ZOOM

INTERVAL

ALARM SIGN

OFF

DEMO

OFF

PRESET

OFF

BACK

CONTINUE (ñ)

PRESET

OFF

BACK

APERTURE SETTING

H í------ú------ü

V í------ú------ü

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIFICATIONS

Pickup device

Effective pixels

Horizontal resolution

Lens

: 1/4"

: 752 (H) x 582 (V)

: Over 520 TV lines

: 22 power zoom lens, f=4.0 – 8.8mm (F1.6 –

3.8)

Motion detector

Privacy masking

: ON/OFF, ON allows setting of detection

patterns on a 48 zone screen for 6 motion

settings (size, masking, sensitivity, zoom,

interval, alarm sign)

: ON/OFF, max of 4 masked locations

Password lock possible

Electronic zoom and gearing

Zoom speed setting possible

Alarm input/output

(back panel control

terminals)

Electronic zoom

: 16 power (combined with optic zoom gives

352 power max)

Max zoom magnification setting possible

Vertical resolution ON/OFF setting

: AUTO/MANUAL

AF area setting possible (3 step)

: Alarm input: 1 (for external alarm switch)

Alarm output: 1 (for sending a signal to the

system controller or an alarm detection

device such as a buzzer)

Autofocus

Iris control

Mirror image effect

: Horizontally (H), vertically (V), horizontally

and vertically (HV)

: ON/OFF, 16 characters

: 9 (0 – 8) screen files can be established, and

each file can set 7 capturing characteristics

such as iris

: AUTO/MANUAL, 1/2 EV steps

Camera ID

View settings

Synchronization method : Internal synchronization/Line lock,

V phase adjustment possible

Lowest image illumination: 2.0 lx (F1.6) at max AGC gain

0.06 lx (F1.6) at x32 electronic sensitivity

boost

Communications

Operational

temperature/humidity

Power source

Power consumption

Weight

: Coaxial control, RS-485

S/N

Backlight compensation : Multi-spot evaluative metering

5 spot centerweighted average metering

: Over 48dB

: –10 – 50°C/below 90% RH

: 24 V AC, 50 Hz/12 V DC

: 4.5 W

48 multi-spot metering

: 380 g

Electronic shutter

• ^{Fast shutter speed mode (SHORT);}

1/50, 1/120, 1/250, 1/500, 1/1000,

1/2000, 1/4000, 1/10000

• ^{Slow shutter speed mode (LONG);}

x1, x2, x4, x8, x16, x32

Electronic sensitivity

boosting

: AUTO/OFF, works with auto iris

Up to x32 max setting possible

White balance

AGC gain

: ATW/AWC/MWB

: ON allows selection of 0dB, +6dB, +9dB, –6dB

OFF allows manual adjustment from 0dB to

30dB

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIFICATIONS

Dimensions

54 mm

5.5 mm

124.3 mm

115 mm

9.3 mm

1/4"-20UNC

External appearance and specifications subject to change

without notice.

Download from Www.Somanuals.com. All Manuals Search And Download.

Radio Shack Electronic Keyboard MD501 User Guide
Raymarine Marine Instruments 86124 1 User Guide
Rotel Stereo Amplifier RA820BX3 User Guide
RuggedCom Switch RSG2200 User Guide
Ryobi Trimmer 990r User Guide
Samson Home Theater System XP106 User Guide
Samsung Flat Panel Television LE26A41B User Guide
Samsung Refrigerator RB215BSSW User Guide
Sanus Systems Indoor Furnishings CFR115 User Guide
Sanyo Computer Monitor VMC L1017 User Guide