Download from Www.Somanuals.com. All Manuals Search And Download.
FCC INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
CAUTION: FCC Regulations state that improper modifications or unauthorized changes to this unit may void
the user’s authority to operate the unit.
PC RESOLUTION CHART
TRADEMARKS
Manufactured under license from
Dolby Laboratories. Dolby and the
double-D symbol are trademarks of
Dolby Laboratories.
HDMI, the HDMI Logo and High-
Definition Multimedia Interface are
trademarks or registered trademarks
of HDMI Licensing LLC in the United
States and other countries.
®
As an Energy Star Partner, Sanyo
Manufacturing Corporation has deter-
mined that this product meets the
®
Energy Star guidelines for energy
efficiency.
This symbol on the nameplate means
the product is Listed by Underwriter’s
Laboratories Inc. It is designed and
manufactured to meet rigid U.L. safety
standards against risk of fire, casualty
and electrical hazards.
®
®
®
Adobe , Adobe Flash , and Flash Lite
are either registered trademarks or
trademarks of Adobe Systems
Incorporated in the United States
and/or other countries.
This Class B digital apparatus complies with Canadian
ICES-003.
Need help?
1-877-864-9604
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
CONTENTS
Power Requirement: Source: AC 120V, 60Hz
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . 2
FCC INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
TRADEMARKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
PC RESOLUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
PROTECTING THE SCREEN . . . . . . . . . . . . . . . . . . . . . . . . .4
POSITIONING THE HDTV . . . . . . . . . . . . . . . . . . . . . . . . . . .5
STAND REMOVAL / WALL MOUNTING . . . . . . . . . . . . . . .5
GETTING STARTED—
AC Power Consumption:
Weight:
195 watts
75 lbs.
Dimensions:
MODEL
WIDTH
HEIGHT
DEPTH
DP55360
w/o stand
51.2
34.5
32.3
10.9
2.4
NOTE: Dimensions are in inches
Remote Control Battery Installation . . . . . . . . . . . . . . . .5
Antenna Connections for off-air or cable . . . . . . . . . . .5
HDTV INPUT/OUTPUT REFERENCE . . . . . . . . . . . . . . . . . . .6
A/V CONNECTIONS (SIDE PANEL) . . . . . . . . . . . . . . . . . . .7
A/V CONNECTIONS (BACK PANEL) . . . . . . . . . . . . . . . . . .8
POWER CONNECTION / INITIAL CHANNEL SEARCH . . .9
REMOTE CONTROL OPERATION . . . . . . . . . . . . . . . . . . . .10
ON-SCREEN MENU OPERATION—
Channel / Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Channel Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Channel Scan Memory . . . . . . . . . . . . . . . . . . . . . . .11
Input Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Video3 Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
HDMI Linking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Menu Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Digital Caption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Energy Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Clock Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Motion Sync . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
V-Chip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
PC CONNECTIONS & MENU OPERATION . . . . . . . . . . . .18
PHOTO VIEWER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Please read before
operating your HDTV!
PROTECTING THE SCREEN
CAUTION: The screen can be damaged if it is not
maintained properly.
Do not use hard objects such as hard cloth or
paper to clean the screen.
•
Do not use excessive pressure when cleaning
the screen; excessive pressure can cause
permanent discoloration or dark spots.
•
NEVER spray liquids on the screen.
•
HANDLING PRECAUTIONS
Handle by the cabinet only.
•
Never touch the screen when handling.
•
Handling damage is not covered under warranty.
•
POSITIONING THE HDTV
Always use a firm and flat surface when
positioning your HDTV.
•
“The Amercian Academy of Pediatrics discourages
television viewing for children younger than two
years of age”
Do not position the unit in a confined area.
•
Allow adequate space for proper ventilation.
•
Need help?
1-877-864-9604
4
Download from Www.Somanuals.com. All Manuals Search And Download.
STAND REMOVAL AND WALL
GETTING STARTED
MOUNTING (OPTIONAL)
BATTERY INSTALLATION
Tools Needed: Phillips screwdriver
Install two (2) “AAA” batteries in the remote
control. (Not included)
IMPORTANT NOTE: Place HDTV face down
on a padded or cushioned flat surface to
protect the screen and finish.
To ensure safe operation, please observe the
following precautions:
Wall mounting of the HDTV must be performed
by a skilled person.
• Replace both batteries at the same time. Do not use a
new battery with a used battery.
Remove the two (2) screws holding the stand
base cover and carefully dislodge.
1
• There’s a risk of explosion if a battery is replaced by
an incorrect type.
• Do not expose the Remote Control unit to moisture
or heat.
• Be sure to match the “+” and “–” signs on the
batteries with marks inside the remote control.
Remove the four (4) screws securing the
stand base to the HDTV. CAUTION: Hold the
stand firmly as you remove the last screw.
ANTENNA CONNECTION FOR
OFF-AIR SIGNALS OR CABLE
2
Hook up your antenna or your cable service to
the HDTV’s ANT terminal with the use of a 75
OHM coaxial cable.
NOTE: Keep your indoor antenna at least 3 ft. away
from the television set and any other electronic
equipment.
Use the screws that are threaded into the four
(4) inserts on the back of your HDTV to secure
it to an appropriate wall mounting kit.
ANTENNA
3
ANALOG / DIGITAL
ANTENNA IN
CABLE
The tuner in this HDTV can receive:
• Digital and Analog off air signals from an antenna
VESA standard interface: 400 x 400
• Analog or ClearQAM cable channels from a direct
Cable TV connection.
Mounting screws measurements:
M6 (6mm) Diameter, Length—12mm (maximum)
NOTE: Wall mounting kit is not included.
Need help?
1-877-864-9604
5
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED
7
8
HDTV INPUT/OUTPUT REFERENCE
2
1
HDTV BACK PANEL
6
3
4
5
S-Video Input (VIDEO1)
1
NOTE: An S-Video connection will override a connection to
the Video1 (yellow) input jack.
9
2
3
Composite AV Input (VIDEO1) – Yellow (Video),
plus white and red (Audio) input jacks.
HDTV
SIDE PANEL
10
Component AV Input (VIDEO2) – Green (Y), blue
(Pb), and red (Pr) Video inputs plus the white and
red Audio inputs.
4
5
Stereo Audio Out (L/R) Jacks
11
12
HDMI (INPUT2 & 3) – An all digital AV interface
accepting uncompressed video signals up to
1080p for the best picture possible.
Analog / Digital Antenna Input – Connect a 75 OHM
cable from an antenna or direct Cable service.
6
USB Input
10
11
Digital Audio Output (Coaxial)
7
8
View pictures stored in a USB flash drive.
AV Component Input (VIDEO3) – Green (Y), blue
(Pb), and red (Pr) Video inputs plus the white and
red Audio inputs.
HDMI (INPUT1) – An all digital AV interface
accepting uncompressed video signals up
to 1080p for the very best picture possible.
NOTE: A Composite connection is possible via VIDEO
INPUT3 using the Y (VIDEO) jack and the L/R audio
jacks. (See Video 3 Setting on page 12.)
NOTE: A DVI connection is possible via the HDMI
INPUT1 (DVI) using an appropriate adapter
and the VIDEO3 Audio jacks for sound output.
9
PC Input and Stereo Audio (Mini)
12
ETHERNET Port
Hook up your HDTV to the internet with the
use of an appropriate ethernet cable and a
correct internet setup.
NOTE: Please refer to the cTV Guide for the proper
connection to your Local Area Network (LAN).
• MONITOR RGB (D-SUB)
• AUDIO R/L (Stereo Mini Jack)
NOTE: See page 18 for proper PC hookup and setup.
Need help?
1-877-864-9604
6
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED
AUDIO / VIDEO CONNECTIONS (SIDE PANEL)
COMPONENT connections will accept SDTV,
Digital Audio Output is used to output the HDTV’s
EDTV and HDTV video signals. Use them for great
image quality from digital devices such as a DVD
player or Video Game system.
Audio through your home theater system.
Hook up the HDTV’s Digital Audio Output to your
home theater system’s input with the use of a
phono-type Digital Audio cable.
Match your digital device’s Component output jacks
to either of the two (2) Component input jack sets
(VIDEO2 or VIDEO3) on your HDTV.
DVD PLAYER
(or similar device)
MULTICHANNEL RECEIVER
(or home theater system)
USB input jack is used to connect a USB mass
storage device to display digital images on your
HDTV. (JPEG only.)
DVD PLAYER
(or similar device)
USB FLASH DRIVE
DVI
HDMI (DVI) INPUT1 can be used to hookup a DVI
device with the use of an appropriate DVI to HDMI
cable or adapter. VIDEO3 Audio in L/R jacks need to
be hooked up to the DVI device as well
NOTE: HDMI INPUT1 may also be used to hookup any digital
device with an HDMI output, without the use of the L/R
audio jacks.
NOTE: Audio/Video cables
are not supplied.
Need help?
1-877-864-9604
7
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED
AUDIO / VIDEO CONNECTIONS (BACK PANEL)
COMPOSITE connections are used to hookup
your analog equipment such as a VCR or an older
DVD player.
VCR
Hook up you analog device’s yellow video output
jack and corresponding audio output jacks to the
HDTV’s Video Input 1 composite jacks.
(or analog device)
NOTE: Always match the color of your device’s output jack,
the connector and the HDTV’s input jack.
S-Video jack may be used instead of the yellow
Composite video input with the use of an S-Video
cable connected from your device’s S-Video out-
put to the HDTV’s S-Video input.
SATELLITE RECEIVER
HDMI
(or similar device)
STEREO AMPLIFIER
Use HDMI INPUT1, 2 & 3 to hookup HD digital
devices such as a Blu-ray player, HD Cable Box,
HD Satellite Receiver or Video-game System.
Audio Output L/R are used to hookup an external
stereo Amplifier. Connect your home stereo’s
input jacks to the HDTV’s Audio Output jacks with
a pair of audio red and white connectors.
NOTE: Do not connect external speakers directly to the
HDTV.
Connect your digital device’s HDMI output to any
of the three (3) HDMI inputs on your HDTV with
the use of an HDMI cable.
Need help?
1-877-864-9604
8
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED (CONTINUED)
INITIAL CHANNEL SEARCH
Before proceeding, please make sure to hook up
your antenna or cable connection and all AV
equipment correctly to your HDTV.
PLUG IN AC POWER CORD
120V AC, 60Hz
INITIAL ENERGY SAVING
MODE SCREEN
TURN ON TV (PRESS POWER BUTTON)
Wait for on-screen instructions to set an
Initial Energy Saving Mode, and perform an
Initial Channel/Signal Search.
TV SET LOCATION SELECTION:
Select “Home Mode” by pressing the CHM key to set
the HDTV’s backlight to an Energy Star qualified level,
or select “Store Mode” by pressing CHL to set the
backlight to a retail display level.
CHANNEL AND AV SIGNAL SEARCH:
INITIAL CHANNEL/SIGNAL SEARCH
SETUP SCREEN
Press the CHLM key to perform a channel
search from an Antenna or a direct Cable
connection, and a signal search from devices
hooked up to the HDTV’s AV input jacks.
ON SCREEN HELP (OPTIONAL)
Press the CHM key if you wish to access an
on screen trouble shooting guide.
NOTE: On screen help is also accesible via the
main menu.
CHANNEL SEARCH PROGRESS SCREEN
CHANNEL AND SIGNAL SETUP SCREEN
The final setup screen displays analog and digital
channels found as well as AV inputs detected. Pressing
the CHLM key finalizes the setup process.
NOTE: To repeat the initial setup process press VOLM.
AV INPUT SELECTION
Press the INPUT key to select the correct AV
input for the video source you wish to watch.
CHANNEL/SIGNAL LIST SCREEN
Need help?
1-877-864-9604
9
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL OPERATION
• MUTE Key—Mute or restore the sound.
• POWER Key—Turns your HDTV On or Off.
• RECALL Key—Switch between current channel
and last selected channel.
• ECO Key—Modifies the Energy Saver level (see
page 13.)
• NET@ Key—Shortcut key to select the Net input
directly and display the Internet Entry screen.
• AUDIO Key—Selects the desired Audio mode.
Stereo, Mono, or SAP (when available.)
• HDMI Key—Cycles through the HDMI inputs.
• ON TIMER Key—Displays the current switch on
time (see Clock Timer on page 14.)
• USB Key—Selects the USB input directly.
• CAPTION Key—Cycles through the available
Caption modes.
• MENU Key—Displays or hides the on-screen
menu.
• RESET Key—Pressing it twice restores your
HDTV to its factory settings. All user customized
settings will be cleared.
• HELP Key—Displays on-screen Help menu.
• LiNKS Key—Show or hide the available widgets.
Serves as a Home key for the content services
when navigating the Net input.
• SLEEP Key—Displays the “Off” Timer. While Off
Timer is on-screen, press the “0” key to Set the
amount of time (in 30 minute increments) at
which the HDTV will turn off.
• EXIT Key—Exits the on-screen menu.
Return to the previous screen when navigating
the Net input.
• PIX SHAPE Key—Cycles through the available
aspect ratios. The different settings either
stretch, zoom, or fill the image on your screen.
Bars may appear on top and bottom of your
screen (or on left and right sides) depending on
the broadcasted signal or program.
• Cursor L (UP) M (DOWN) keys—Move the on-
screen cursor up and down.
• Cursor ꢀ (LEFT) ꢁ (RIGHT) keys—Move the on-
screen cursor left and right.
NOTE: Pix6-7 are setup as Pix1-2 in PC mode. Use of
Pix6-7 in TV mode is not recommended.
• ENTER Key—Set or select the highlighted option
on the screen.
• INFO Key—Displays the Channel Information
banner.
The PLAY, PAUSE, STOP, REW, FF, W, T, CAMERA,
and XACTI MENU keys control playback features
on a Sanyo Xacti digital camera when the HDMI-
CEC feature has been activated on both the HDTV
and the Xacti camera (see HDMI Linking feature
on page 12.)
• NUMERICAL Keys—Select channels directly.
NOTE: For channels 100 and up, press and hold the
first number, then enter the remaining two numbers.
–
•
(sub ch) Key —Allows for the direct selection
of digital subchannels. For example: to select
NOTE: These playback keys may or may not react with
other devices other than the Xacti camera.
–, and 1 keys.
channel 39.1 press the 3, 9,
• INPUT Key—Selects the video source to view.
Holding down the key displays the Input List.
–
• Volume
audio level.
Keys—Increases or decreases the
+
• Channel L M Keys—Scan through the channels
in the memory database.
Need help?
1-877-864-9604
10
Download from Www.Somanuals.com. All Manuals Search And Download.
ON-SCREEN MENU OPERATION
CHANNEL / INPUT ____________
Display the On Screen menu and use the
CURSOR LM keys to select Channel / Input.
Press ENTER.
Channel Search
Auto – Searches the detected mode, Cable or Air.
Cable – Searches for analog and unscrambled
(ClearQAM) digital cable channels.
MAIN MENU SCREEN
Air (Antenna) – Searches for analog and digital off-air
channels.
Digital Add-On – Searches digital off-air channels
adding newly found digital channels to the channel
map database.
NOTE: Digital Add-On option is not available when the
current mode is Cable.
Channel Scan Memory
Channel Scan Memory lists all Analog and Digital
channels found. It also lists Analog channels that were
not found, which can be added.
CHANNEL SETTING SCREEN
Use the CURSOR LM keys to move the channel select
bar throuh all enabled and disabled channels, or use
the CH LM keys to skip all disabled channels.
Press ENTER to enable or disable the selected channel.
NOTE: For information on local digital channels, visit
IMPORTANT FACT: This HDTV maintains only one database of
digital channels. Therefore, when you search for cable chan-
nels, the database of antenna digital channels will be deleted.
You will only be able to receive those ClearQAM channels your
cable company provides.
CHANNEL SCAN MEMORY SCREEN
Input Setting
Input Setting feature allows the removal of unused
inputs from the AV input loop.
Use the CURSOR LM keys to select an AV input. Press
ENTER to disable (uncheck) or enable (check) the high-
lighted input.
INPUT SETTING SCREEN
NOTE: At least one input must and will remain enabled.
:Skip is for reference only.
Need help?
1-877-864-9604
11
Download from Www.Somanuals.com. All Manuals Search And Download.
ON-SCREEN MENU OPERATION
CHANNEL SETTING ___________
Video3 Setting
Use this feature to establish either a Component or
Composite connection to the VIDEO INPUT 3 jacks on
your HDTV.
Use the CURSOR LM keys to select the type of hook up
that will be used in the Video3 input.
Press ENTER, a blue mark will appear next to the
selected option.
VIDEO3 SETTING SCREEN
HDMI Linking
NOTE: Designed for use with
a
Sanyo Xacti Digital
VIdeo/Movie Camera, and may not support all HDMI-
CEC functions of other equipment.
Use the HDMI-CEC Function to enable or disable all
available CEC functions.
HDMI Power ON Sync and Power OFF Sync enable
specific features including the automatic power ON
process and power OFF process.
HDMI LINKING SCREEN
Xacti-LINK
With a Sanyo Xacti Digital Video/Movie
Camera hooked up to your HDTV’s
HDMI input, setting the HDMI-CEC
Function to ON enables you the use of
keys on your GXEB remote to operate
your Xacti camera.
NOTE: The HDMI-CEC function of the Xacti camera must also
be turned ON to enable the Xacti-Link.
Need help?
1-877-864-9604
12
Download from Www.Somanuals.com. All Manuals Search And Download.
ON-SCREEN MENU OPERATION
SETUP _________________________
Display the On Screen menu and use the
CURSOR LM keys to select Setup.
Press ENTER.
Menu Language
Choose the language in which the On Screen menus
will be displayed.
• English
• Español
• Français
MAIN MENU SCREEN
Press ENTER on the desired language.
Digital Caption
Captioning is textual information transmitted along
with the picture and sound. Turning Captioning ON (by
pressing the CAPTION key during normal TV viewing)
causes the HDTV to open these captions (digital or
analog) and superimpose them on the screen.
MENU LANGUAGE SCREEN
NOTE: Local broadcasters decide which caption signals to
transmit.
Use the CURSOR LM and ꢀ ꢁ keys to modify Font,
Background, and Foreground of digital caption text.
Energy Setting
Use the Energy Saver and Light Sensor features found
under Energy Setting to lower power comsumption by
controlling the LED backlight brightness levels.
DIGITAL CAPTION SCREEN
Energy Saver – This settings control the LCD backlight
brightness to reduce power consumption.
• Level 1: Energy Saver feature is off.
• Level 2: Low power consumption.
• Level 3: Lowest power consumption.
Press ENTER on the desired level.
NOTE: ECO key may also be used as a shortcut to modify the
Energy Saver settings.
ENERGY SAVER SCREEN
Need help?
1-877-864-9604
13
Download from Www.Somanuals.com. All Manuals Search And Download.
ON-SCREEN MENU OPERATION
Light Sensor – Detects ambient room light brightness
and uses that reading to control the panel brightness
level and picture parameters to reduce the HDTV’s
power consumption.
NOTE: When room lighting is dark, the panel brightness
and/or the picture setting parameters such as bright-
ness and cotrast are lowered. When room lighting is
bright, parameters are affected opposite.
LIGHT SENSOR SCREEN
Clock Timer
This feature allows you to set a Current Time for your
HDTV and enable a Switch On Time for the HDTV to
turn on at a specific time of day.
When On Timer Function is set to ON, the TV will
automatically turn on at the previously set Switch on
Time.
CLOCK TIMER SCREEN
Motion Sync
Your HDTV will display all signals at
the refresh rate of 120Hz. Motion Sync
is a special Frame Rate Converter fea-
ture that helps eliminate motion blur
and film judder in scenes with fast
action.
• On – Takes full advantage of your TV’s refresh rate
capabilities for the best picture quality.
• Off – Disables the Motion Sync feature.
MOTION SYNC SCREEN
Need help?
1-877-864-9604
14
Download from Www.Somanuals.com. All Manuals Search And Download.
ON-SCREEN MENU OPERATION
SETUP ________________________
V – Chip (Parental Control)
Use this feature to automatically block programs with
content you deem as inappropriate for viewing by
your children.
NOTE: This feature is designed to comply with the United
States of America’s FCC V-Chip regulations. Therefore,
it may not function with broadcasts that originate in
other countries.
V-CHIP SETUP SCREEN
ADJUSTING THE V-CHIP RATINGS
Select ON and press ENTER.
Select Adjust (Standard) and press ENTER.
Use the CURSOR L M and ꢀ ꢁ keys to navigate and
the ENTER key to Block or Unblock a selected rating. A
lock symbol will appear beside the selected rating
option indicating that it is blocked.
NOTE: Blocking a rating will automatically block all higher
ratings. Unblocking a rating automatically unblocks
all lower ratings.
ADJUST (STANDARD) SCREEN
ADVANCED V-CHIP SYSTEM (RRT5)
RRT5 (V-Chip Regional Ratings 5) is an advanced V-Chip
ratings system for digital channels that are received
with an antenna.
When the HDTV detects compatible RRT5 data, it’s
downloaded & stored in memory, and the Setup
V-Chip screen is then modified to show the Adjust
(Advanced) option.
Use the CURSOR L M and ꢀ ꢁ keys to highlight the
different options, and use the ENTER key to block or
unblock the selected rating.
V-CHIP SETUP SCREEN WITH ADJUST
(ADVANCED) OPTION
NOTE:There may be more ratings than can be displayed on
one screen. When vertical scroll bars appear, press
CURSOR LM to gain access to the additional ratings.
MORE INFORMATION
Additional information about MPAA (Motion Picture
Association of America) and V-Chip rating can be
respectively.
ADJUST (ADVANCED) SCREEN
Need help?
1-877-864-9604
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ON-SCREEN MENU OPERATION
PICTURE ____________________
Display the On Screen menu and use the
CURSOR LM keys to select Picture. Press ENTER.
You may choose between Vivid, Mild, , and Standard,
which have predetermined fixed picture parameter
values, or choose the Manual option for customized
personal settings.
NOTE: Each AV input can have its own picture mode (pre-
determined or manual.) Current input’s selected
option is indicated by a blue marker.
MAIN MENU SCREEN
MANUAL PICTURE SETTINGS
Manual parameters to adjust include:
Color
Tint
Contrast
•
•
•
•
•
•
Brightness
Sharpness
Dynamic Contrast
The Detailed Setting option allows for the adjustment
of 7 additional parameters such as:
Signal Balancer
White Balance
Noise Reduction
Vertical Sharpness
H-Size
•
•
•
•
•
•
•
PICTURE SCREEN (MANUAL)
Edge Enhancer
V-Size
NOTE: Default Picture option returns all picture parameters to
their original factory settings.
ADJUSTING A PICTURE SETTING
Use the CURSOR LM keys to highlight the picture
parameter you wish to adjust. Press the ENTER key to
enter the value adjustment screen. Modify the selected
parameter’s value by pressing the CURSOR ꢀ ꢁ keys.
PARAMETER SELECTION SCREEN
NOTE: CURSOR LM keys select the next/previous parame-
ter without returning to the previous menu screen.
Once adjustments are complete, press the EXIT key to
return to normal TV viewing.
VALUE ADJUSTMENT SCREEN EXAMPLES
Need help?
1-877-864-9604
16
Download from Www.Somanuals.com. All Manuals Search And Download.
ON-SCREEN MENU OPERATION
SOUND _____________________
Display the On Screen menu and use the
CURSOR LM keys to select Sound. Press ENTER.
Choose an option for your sound settings:
Auto – Sound settings are linked to the current Picture
option and parameters are adjusted accordingly.
Dynamic, Mild, Standard – 3 different predetermined
sound parameters not linked with any Picture option.
MAIN MENU SCREEN
MANUAL PARAMETER SCREEN
DETAILED SETTING SCREEN
MANUAL SOUND SETTINGS
The Manual option provides different parameters that
can be personally adjusted:
Bass
Treble
Detailed Setting
•
•
•
– 4-Band Equalizer: Personalize audio highs and lows.
NOTE: Default Sound option returns all sound parameters to
their original factory settings.
ADJUSTING A SOUND SETTING
Use the CURSOR LM keys to highlight the sound
parameter you wish to adjust. Press the ENTER key to
enter the value adjustment screen. Modify the selected
parameter’s value by pressing the CURSOR ꢀ ꢁ keys.
NOTE: CURSOR LM keys select the next/previous parame-
ter without returning to the previous menu screen.
Once adjustments are complete, press the EXIT key to
return to normal TV viewing.
VALUE ADJUSTMENT SCREEN EXAMPLES
Need help?
1-877-864-9604
17
Download from Www.Somanuals.com. All Manuals Search And Download.
PC INPUT
Use your HDTV as a computer monitor by hooking
up your PC or Laptop to the TV with the use of an
appropriate monitor cable (not included.)
PC Setting
Auto Adjustment – Automatically adjusts display
position, dot clock and phase.
Before connecting any cables, disconnect the
AC power cords of both the HDTV and PC from
the AC outlets.
Dot Clock – Adjust the Dot frequency to match
your computer’s Dot frequency.
Phase – Adjust this parameter when the picture
appears to flicker or is blurred.
Power on the HDTV and any other peripheral
equipment before powering on the computer.
H-Position – Move the image horizontally
To avoid an “Out of Range” condition please set
your PC’s output resolution to one compatible with
your HDTV. See PC Resolution chart on page 3.
V-Position – Move the image vertically
Power Saving – Enable the HDTV to turn to
Standby Mode when computer is not in use.
NOTE: If computer has only DVI Output, a DVI to RGB
adapter will be required, or, a DVI to HDMI cable
and RCA audio cables (see HDMI (DVI) INPUT1 on
page 7.)
RGB OUTPUT
JACK
DVI OUTPUT
JACK
HDTV SIDE PANEL
Stereo mini
audio cable
PC SETTING SCREEN
PC OR LAPTOP
PC Picture and Sound
Standard – Sets predetermined values to the
Picture or Sound parameters.
RGB Monitor
cable
Sanyo recommends using a
monitor cable that includes
a Ferrite Core.
Manual – Adjust Contrast, Brightness, and Color
Temperature screen settings, and the Bass and
Treble audio settings.
Laptop Display
When using your Sanyo HDTV to display a
Laptop’s screen display, holding down the Fn (or
FN) key while pressing the appropriate function
key (F5, F7, F8, etc) should cycle through different
display modes between the laptop and the HDTV.
Modes may include displaying only on the laptop
screen, on both the laptop and the HDTV, or
displaying only on the HDTV.
Hold down
and press
PC PICTURE AND SOUND SCREENS
NOTE: Fn key and function key symbols on the laptop’s
keyboard may vary from one brand to another.
NOTE: These settings do not affect normal TV viewing.
Need help?
1-877-864-9604
18
Download from Www.Somanuals.com. All Manuals Search And Download.
USB INPUT
PHOTO VIEWER __________________
View pictures on your HDTV with the use of a USB
mass storage device (not included.)
Any of the two USB inputs on your HDTV may be used.
NOTE: When two devices are hooked up, only the first one is
recognized and available as an input.
USB FLASH
DRIVE
THUMBNAIL VIEW SCREEN
NOTE: A thumbnail hide icon will appear if a
picture cannot be decoded or if no
thumbnail data is available.
NOTE: The HDTV switches to USB
Input when a USB flash drive is
detected.
USING THE PHOTO VIEWER
Press ENTER on a thumbnail photo to enable the
Rotate, Full View and Start Slideshow functions.
Once in Full View mode:
Use the CURSOR ꢀ ꢁ keys to change picture.
Press ENTER to show the full view options menu.
SLIDE SHOW
SETUP MENU
FULL VIEW
OPTIONS MENU
SLIDE SHOW
In the Slideshow Setup menu you may turn the Shuffle
and Quick Change options ON or OFF.
Press ENTER on Start Slideshow from the Thumbnail
View Screen or from the full view options menu to
start the slideshow from the current picture.
JPEG VIEWER USB MENU
Press MENU when in Full View or Slideshow mode to
display the USB On screen menu.
Picture Setting
–
Adjust Color, Tint, Contrast,
Brightness, Sharpness and Dynamic Contrast.
NOTE: Picture Settings are separate configurations from the
settings in TV and AV inputs.
USB MAIN MENU SCREEN
Need help?
1-877-864-9604
19
Download from Www.Somanuals.com. All Manuals Search And Download.
ONE-YEAR LIMITED PARTS AND LABOR WARRANTY
THIS LIMITED PARTS AND LABOR WARRANTY IS VALID ONLY ON SANYO TELEVISIONS PURCHASED AND USED IN
THE UNITED STATES OF AMERICA, CANADA, AND PUERTO RICO, EXCLUDING ALL OTHER U.S. TERRITORIES AND
PROTECTORATES. THIS LIMITED WARRANTY APPLIES ONLY TO THE ORIGINAL RETAIL PURCHASER, AND DOES NOT
APPLY TO PRODUCTS USED FOR INDUSTRIAL OR COMMERCIAL PURPOSES.
WARRANTY APPLICATION
FOR ONE YEAR from the date of original retail purchase Sanyo Manufacturing Corporation (SMC) warrants this TV to
be free from manufacturing defects in materials and workmanship under normal use and conditions for parts and labor.
For the FIRST 90 DAYS from the date of original retail purchase, Sanyo Manufacturing Corporation will replace any
defective TV via exchange at the retailer. To ensure proper warranty application, keep the original-dated-sales receipt
for evidence of purchase. Return the defective TV to the retailer along with the receipt and the included accessories,
such as the remote control. The defective TV will be exchanged for the same model, or a replacement model of equal
value, if necessary. Replacement model will be contingent on availability and at the sole discretion of Sanyo
Manufacturing Corporation.
THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE.
OBLIGATIONS
For one year from the date of purchase, Sanyo Manufacturing Corporation warrants this product to be free from
defects in material and workmanship under normal use and conditions. During the first 90 days under this warranty
for any manufacturing defect or malfunction Sanyo Manufacturing Corporation will provide a new TV via exchange at
the retailer.
HOW TO MAKE A CLAIM UNDER THIS WARRANTY
Please call 1-877-864-9604. Please be prepared to give us the television’s model number and serial number when you
call. The model number and serial number are printed on a label attached to the back of the unit.
For customer assistance, call toll free 1-877-864-9604.
Hours of operation: Monday – Friday 7:30 AM - 7:00 PM CST
This warranty expresses specific contractual rights; retail purchasers may have additional statutory rights which vary
from state to state.
(EFFECTIVE: March 1, 2007)
Your Sanyo HDTV is registered at the time of purchase, please keep sales receipt for future reference.
For your protection in the event of theft or loss of this product, please fill in the information requested
below and KEEP IN A SAFE PLACE FOR YOUR OWN PERSONAL RECORDS.
Model No.______________________________
Date of Purchase _________________________
Purchase Price___________________________
Where Purchased_________________________
Serial No.______________________________
(Located on back of unit)
Sanyo Manufacturing Corp.
3333 Sanyo Road, Forrest City, AR 72335
Need help?
1-877-864-9604
20
Download from Www.Somanuals.com. All Manuals Search And Download.
ESTE SÍMBOLO INDICA QUÉ VOLTAJES PELIGROSOS QUE CONSTI-
TUYEN UN RIESGO DE CHOQUE ELÉCTRICO ESTÁN PRESENTES DEN-
TRO DE ESTA UNIDAD.
PRECAUCIÓN
RIESGO DE CHOQUE ELÉCTRICO ¡NO ABRIR!
ESTE SÍMBOLO INDICA QUE HAY INSTRUCCIONES IMPORTANTES DE
OPERACIÓN Y MANTENIMIENTO EN LA LITERATURA QUE SE ANEXA A
ESTA UNIDAD.
PRECAUCIÓN: PARA REDUCIR EL RIESGO DE CHOQUE ELÉCTRICO, NO QUITE LA CUBIERTA
(O LA TAPA TRASERA). NO HAY PARTES ADENTRO QUE LAS PUEDA REPARAR EL USUARIO.
REFIÉRASE A PERSONAL CALIFICADO PARA REPARAR EL APARATO.
ADVERTENCIA: PARA REDUCIR EL RIESGO DE FUEGO O CHOQUE ELÉCTRICO, NO EXPONGA ESTE
APARATO A LLUVIA O HUMEDAD.
IMPORTANTES MEDIDAS DE SEGURIDAD
15. Si una antena externa se ha conectado al televisor,
asegúrese que el sistema de tierra de la antena esté de
forma que provea alguna protección contra fugas de volta-
je o cargas electrostáticas. En la sección 810-21 del código
eléctrico nacional de los Estados Unidos se menciona infor-
mación con respecto a la manera adecuada de instalar el
sistema de tierra al mástil principal, aterrizaje del cableado
para la unidad de descarga de la antena, tamaño de los con-
ductores de tierra, localización de la unidad de descarga
de la antena, conexión a los electrodos de tierra, y
requerimientos de los electrodos de tierra.
1. Lea estas instrucciones.
2. Guarde estas instrucciones.
3. Preste atención a los avisos.
4. Siga todas las instrucciones.
5. No use este aparato cerca del agua.
6. Limpie sólo con un trapo seco.
7. No obstruya las aperturas para ventilación. Instale de
acuerdo a las instrucciones del fabricante.
8. No se instale cerca de ninguna fuente de calor como
radiadores, registros de calor, estufas, u otros aparatos
(incluyendo amplificadores) que produzcan calor.
16. Un sistema de antena externo no debe instalarse cerca de
líneas de electricidad o circuitos de potencia o alumbrado, o
donde puedan caer sobre líneas de energía eléctrica o
circuitos cuyo contacto con ellos puede ser fatal.
9. Por seguridad, no elimine la conexión de tierra de la
clavija. Una clavija polarizada tiene una hoja más ancha que
la otra. Una clavija de tipo conexión a tierra, tiene dos hojas
y un tercer conector mas prolongado. La hoja ancha o el
conector prolongado están provistas para su seguridad. Si
la clavija proveída no asienta correctamente en el contacto
eléctrico, consulte a un electricista para que esa toma de ac
obsoleta sea remplazada.
EJEMPLO DE ATERRIZAMIENTO DE ANTENA DE ACUERDO
AL CÓDIGO ELÉCTRICO NACIONAL
(National Electrical Code, ANSI/NFPA 70)
10. Proteja el cordón de potencia de que sea pisado o
perforado, particularmente en las hojas y del punto donde
éste sale del aparato.
11. Sólo use anexos o accesorios especificados por el
fabricante.
“Nota al instalador del sistema de cable CATV :
12. Use únicamente con el carro, estante, tripie,
soporte o mesa especificada por el fabricante, o
vendida con el aparato. Cuando se use un carro,
tenga precaución cuando mueva la combinación
de carro/aparato para evitar lesiones en caso de
que se caiga.
Este recordatorio es dado para llamar la atención del instalador
del sistema de cable CATV al Artículo 820-40 del NEC que
provee guías para el aterrizamiento adecuado y, en particular,
especifica que el cable de tierra deberá de estar conectado al
sistema de tierra del edificio, tan cercano al punto de entrada
del cable como sea práctico.”
13. Desconecte este aparato en caso de tormenta eléctrica o
cuando no se use por un periodo de tiempo prolongado.
17. Montaje en pared o techo—Este producto deberá de ser
montado en la pared o techo siguiendo las recomendaciones
del fabricante.
14. Refiera todas las reparaciones a personal de servicio califi-
cado. Se requiere de servicio cuando el aparato se ha daña-
do de cualquier forma, como si el cordón de potencia se
dañara de alguna forma, se ha derramado líquido sobre el
aparato o algún objeto le ha caído encima, el aparato se ha
expuesto a la lluvia o humedad, que no opere normalmente
o que se haya caído.
18. Este aparato no deberá de ser expuesto a ser mojado, y no
se deberán de colocar recipientes con líquido encima de él.
19. Si el conector del cable de AC se usa como artículo de
desconexión principal, entonces éste deberá de
permanecer accesible todo el tiempo.
¿Necesita ayuda?
1-877-864-9604
21
Download from Www.Somanuals.com. All Manuals Search And Download.
INFORMACIÓN FCC
Este equipo ha sido probado y se encontró en acuerdo a los límites para un aparato digital Clase B, en acorde
a la Parte 15 de las Reglas FCC. Estos límites están diseñados para proveer una protección razonable contra
interferencia nociva en una instalación residencial. Este equipo genera, usa y puede irradiar energía de radio
frecuencia y si no es instalado o usado de acuerdo a las instrucciones, puede llegar a causar interferencia nociva a
radio comunicaciones. Sin embargo, no es completamente seguro que no ocurrirá interferencia alguna en una
instalación en particular. Si este equipo llega a causar interferencia nociva a la recepción de radio o televisión, la cual
puede ser determinada por medio de apagar y encender el equipo, se recomienda al usuario intentar corregir la
interferencia mediante una o varias de las siguientes medidas:
- Reorientar o mover la antena de recepción.
- Aumentar la separación entre el equipo y el receptor.
- Conectar el equipo a un enchufe en un circuito diferente al cual esté conectado el receptor.
- Consultar al vendedor o a un técnico de radio y televisión con experiencia para más ayuda.
PRECAUCIÓN: Regulaciones de la FCC advierten que modificaciones inadecuadas o cambios no autorizados a
esta unidad pueden anular la autorización del usuario para operar la unidad.
RESOLUCIONES DE PC
MARCAS REGISTRADAS
Manufacturado bajo licencia de Dolby
Laboratories. “Dolby” y el signo de
doble-D son marcas registradas de
Laboratorios Dolby.
HDMI, el logo HDMI y “High-Definition
Multimedia Interface” son marcas re-
gistradas de HDMI Licensing LLC en los
Estados Unidos y otros países.
®
Como un Asociado de ENERGY STAR
,
Sanyo Manufacturing Corporation, ha
determinado que este producto cumple
con los lineamientos en eficiencia
®
energética de ENERGY STAR
.
Este símbolo impreso, significa que
el producto está listado por
Underwriters Laboratories Inc. El dis-
eño y manufactura de este producto,
reúne los rígidos estándares de U.L.,
contra riesgos de incendio, accidentes
o descargas eléctricas.
®
®
®
Adobe , Adobe Flash , y Flash Lite
son marcas registradas o marcas de
Adobe Systems Incorporated en los
Estados Unidos y/o otros países.
¿Necesita ayuda?
1-877-864-9604
22
Download from Www.Somanuals.com. All Manuals Search And Download.
ESPECIFICACIONES
CONTENIDO
Requerimiento de Potencia: AC 120V, 60Hz
IMPORTANTES MEDIDAS DE SEGURIDAD . . . . . . . . .21
INFORMACIÓN FCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
MARCAS REGISTRADAS . . . . . . . . . . . . . . . . . . . . . . . . . .22
RESOLUCIONES DE PC . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
CONTENIDO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
ESPECIFICACIONES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
PRECAUCIONES DE MANEJO Y PANTALLA . . . . . . . . . .23
COLOCACIÓN DE LA HDTV . . . . . . . . . . . . . . . . . . . . . . . . .23
QUITAR LA BASE / MONTAJE EN PARED . . . . . . . . . . . .24
PARA COMENZAR—
Consumo de Potencia:
DP55360 195 watts
Peso:
34 kg. (con base)
Dimensiones:
MODELO
ANCHO
ALTO
PROFUNDO
DP55360
sin base
130
87,7
82,0
27,7
6,0
NOTA: Las dimensiones están en centímetros.
Instalación de baterías al control . . . . . . . . . . . . . . . . .24
Conexión de antena aire/cable . . . . . . . . . . . . . . . . . . .24
CONECTORES DEL PANEL TRASERO . . . . . . . . . . . . . . . .24
REFERENCIA DE ENTRADAS Y SALIDAS . . . . . . . . . . . . .25
CONEXIONES DE AUDIO/VIDEO (PANEL LATERAL) . . .26
CONEXIONES DE AUDIO/VIDEO (PANEL TRASERO) . . .27
CONEXIÓN A CORRIENTE . . . . . . . . . . . . . . . . . . . . . . . . . .28
BÚSQUEDA INICIAL DE CANALES . . . . . . . . . . . . . . . . . .28
OPERACIÓN DEL CONTROL REMOTO . . . . . . . . . . . . . . .29
OPERACIÓN DEL MENÚ EN PANTALLA—
Favor de leer antes de
operar su HDTV!
PROTEGER LA PANTALLA
PRECAUCIÓN: La pantalla podría dañarse si no se
le da un mantenimiento adecuado.
Canal / Entrada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Búsqueda de canales . . . . . . . . . . . . . . . . . . . . . . . .30
Memoria de canales . . . . . . . . . . . . . . . . . . . . . . . . .30
Establecer entradas . . . . . . . . . . . . . . . . . . . . . . . . .30
Configuración de Video3 . . . . . . . . . . . . . . . . . . . . .31
Enlace HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Configuración . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Lenguaje del menú . . . . . . . . . . . . . . . . . . . . . . . . . .32
Subtítulos digitales . . . . . . . . . . . . . . . . . . . . . . . . . .32
Configuración de energía . . . . . . . . . . . . . . . . . . . . .32
Reloj temporizador . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Motion Sync. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
V-Chip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Imagen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Configuración manual de imagen . . . . . . . . . . . . . .35
Sonido . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
aaConfiguración manual de sonido . . . . . . . . . . . . . .36
CONEXIONES DE PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
CONFIGURACIÓN DE PC . . . . . . . . . . . . . . . . . . . . . . . . . . .37
REPRODUCTOR DE IMÁGENES . . . . . . . . . . . . . . . . . . . . .38
GARANTÍA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
• NO use objetos duros como trapos gruesos o
papel para limpiar la pantalla.
• NO utilice presión excesiva cuando se limpie
la pantalla; esto podría causar decoloración per-
manente o puntos negros en la misma.
• NUNCA aplique líquidos en aerosol a la pantalla.
PRECAUCIONES DE
MANEJO
• Manéjese sólo por el gabinete.
• Nunca toque la pantalla cuando esté
manejando la HDTV.
• Daño por manejo no está cubierto por la
garantía.
COLOCANDO LA HDTV
• Siempre utilice una superficie firme y plana al
colocar su HDTV.
“La Academia Americana de Pediatras no
recomienda permitir a niños menores de 2
años ver televisión”
• No se coloque la HDTV en áreas confinadas.
• Mantenga suficiente espacio para una buena
ventilación.
¿Necesita ayuda?
1-877-864-9604
23
Download from Www.Somanuals.com. All Manuals Search And Download.
QUITAR LA BASE Y MONTAJE
PARA COMENZAR
EN PARED (OPCIONAL)
INSTALACIÓN DE BATERÍAS
Herramienta necesaria: Desarmador de cruz.
NOTA IMPORTANTE:
Instale las baterías al control remoto.
( 2 “AAA”, no incluídas)
Coloque la HDTV con la pantalla hacia
abajo sobre una superficie plana
acolchonada para proteger la pantalla
y el acabado de la HDTV.
y
Para una operación segura, favor de observar
las siguientes precauciones:
• Reemplace ambas baterías al mismo tiempo.
No utilice una batería nueva con una usada.
Una persona con experiencia debe realizar el
montaje en pared.
Quite los dos (2) tornillos que sostienen la
cubierta de la base y quite con cuidado.
• Existe riesgo de explosión si las baterías son rem-
plazadas con unas de tipo incorrecto.
1
• No exponga el Control Remoto a calor o humedad.
• Asegúrese que las marcas “+” y “–” de las baterías
correspondan con las del control remoto.
CONEXIÓN DE ANTENA PARA
SEÑALES DE AIRE O CABLE
Quite los cuatro (4) tornillos del pedestal de
soporte. PRECAUCIÓN: Sujete firmemente la
base al quitar el último tornillo.
2
Conecte su antena o servicio de cable a la
entrada ANT de su HDTV utilizando un cable
coaxial (75 OHM).
NOTA: Mantenga su antena para interiores al menos
a un (1) metro de distancia tanto de su HDTV
como de cualquier otro aparato electrónico.
ANTENA
Use los tornillos insertados en los 4 hoyos en
la parte trasera de su HDTV para asegurarla al
estuche especial de montaje (no incluído).
3
ENTRADA DE ANTENA
ANÁLOGA / DIGITAL
CABLE
Esta HDTV puede sintonizar:
• Señales aéreas digitales y análogas de una antena.
• Canales de Cable análogos o sin codificar de una
conexión directa de TV por Cable.
Interfase estándar VESA: 400 x 400
Medida de los tornillos:
Diámetro M6, Longitud – 12mm (máximo)
¿Necesita ayuda?
1-877-864-9604
24
Download from Www.Somanuals.com. All Manuals Search And Download.
PARA COMENZAR
7
8
REFERENCIA DE ENTRADAS Y SALIDAS
2
1
PANEL TRASERO
DE LA HDTV
6
3
4
5
Entrada S-Video (VIDEO1)
1
NOTE: La conexión de S-Video deshabilitará la conexión en
la entrada de VIDEO1 (amarillo)
9
2
3
PANEL LATERAL
DE LA HDTV
Entrada de Video Compuesto (VIDEO1)
Entrada amarilla (video) y entradas roja y blanca (audio).
10
Entrada de video Componente (VIDEO2) Entradas
verde (Y), azul (Pb) y roja (Pr) de video; además de las
entradas de audio roja y blanca.
4
5
Salida de Audio Análogo (L/R)
11
12
Entradas HDMI (INPUT2 y INPUT3)
Interfase completamente digital que acepta
señales de video sin compresión hasta de 1080p
para obtener la mejor calidad de imagen posible.
Entrada de antena análoga / digital – Conecte un
cable de 75 OHM de una antena o del servicio de TV
por Cable directo.
6
Entrada USB – Despliegue fotos en pantalla
10
11
desde su memoria USB.
Salida de Audio Digital (Coaxial)
7
8
Entrada HDMI INPUT1 (DVI) – Interfase
completamente digital que acepta señales
de video sin compresión de 1080p para
obtener la mejor calidad de imagen posible.
NOTE: Una conexión DVI es posible por medio de la
entrada HDMI INPUT1 (DVI) utilizando un
adaptador apropiado y conectando el audio a
las entradas de audio de VIDEO3.
Entrada de video Componente VIDEO3 – Entradas
verde (Y), azul (Pb) y roja (Pr) de video; además de las
entradas de audio roja y blanca.
NOTA: Una conexión Compuesta es posible por medio de
VIDEO INPUT3 usando la entrada Y (VIDEO) y las de
Audio L/R, ver Configuración de Video 3 (pág. 31).
Entrada para PC y estéreo audio (mini)
9
Puerto ETHERNET
12
Conecte su HDTV al Internet utilizando un
cable apropiado de ethernet y una cone-
xión a internet correctamente configurada.
• MONITOR RGB (D-SUB)
• AUDIO R/L (conector estéreo mini)
NOTA: Para conexiones y configuración de PC ver pág. 37.
NOTA: Para más información refiérase a la Guía cTV.
¿Necesita ayuda?
1-877-864-9604
25
Download from Www.Somanuals.com. All Manuals Search And Download.
PARA COMENZAR
CONEXIONES DE AUDIO Y VIDEO (PANEL LATERAL)
La conexión COMPUESTA es utilizada para
Use la salida de Audio Digital para transmitir la
conectar equipo análogo tal como una video-
casetera o un reproductor DVD que no cuente con
salidas de Componente.
salida de Audio de la TV a un sistema externo.
Conecte la salida Digital Audio Output de la HDTV
a su sistema de cine en casa utilizando un cable
tipo “phono” de Audio Digital.
Haga coincidir las salidas Componente de su apara-
to digital con cualquiera de las dos (2) entradas
Componente (VIDEO2 ó VIDEO3) de su HDTV.
REPRODUCTOR DVD
(o aparato similar)
RECEPTOR
MULTICANAL
Utilice la entrada USB para conectar una memoria
USB para desplegar imágenes JPEG en la HDTV.
REPRODUCTOR DVD
(o aparato similar)
DVI
HDMI INPUT1 (DVI) puede ser usado para conectar
un aparato DVI utilizando un cable DVI a HDMI o un
adaptador apropiado. Las entradas de Audio de
VIDEO3 también deben estar conectadas a las sali-
das de audio correspondientes del aparato DVI.
NOTA: La entrada HDMI INPUT1 también puede ser usada para
conectar cualquier aparato con salida HDMI, sin la
necesidad de usar las entradas de Audio.
NOTA: Cables de Audio y Video
no vienen incluídos.
¿Necesita ayuda?
1-877-864-9604
26
Download from Www.Somanuals.com. All Manuals Search And Download.
PARA COMENZAR
CONEXIONES DE AUDIO Y VIDEO (PANEL TRASERO)
La conexión COMPUESTA es utilizada para
conectar equipo análogo tal como una video-
casetera o un reproductor DVD que no cuente con
salidas de Componente.
VIDEOCASETERA
(o aparato análogo)
Conecte la salida amarilla de video y las de audio
correspondientes de su aparato análogo a la
entrada VIDEO INPUT 1 de su HDTV.
NOTA: Haga coincidir los colores de las salidas de su apara-
to con los cables y las entradas de la HDTV.
S-Video puede ser utilizada en lugar del conector
amarillo de video usando un cable de S-Video
conectado de la salida S-Video de su aparato a la
entrada S-Video de la HDTV.
NOTA: Cables de Audio y Video
no vienen incluídos.
AMPLIFICADOR
HDMI
ESTÉREO
HDMI INPUT1, 2 & 3 se utilizan para conectar
aparatos digitales HD como: reproductor Blu-ray,
decodificador de Cable HD, receptor satelital HD o
consola de video juegos.
La Salida de Audio Análogo (L/R) se utiliza para
conectar un amplificador estéreo externo.
Conecte las entradas de su estéreo a las salidas
AUDIO OUTPUT de la HDTV con un par de cables
de audio rojo y blanco.
NOTA: No conecte bocinas externas directamente a la
HDTV.
Conecte la salida HDMI de su aparato digital a
cualqueira de las tres (3) entradas HDMI de su
HDTV utilizando un cable HDMI.
¿Necesita ayuda?
1-877-864-9604
27
Download from Www.Somanuals.com. All Manuals Search And Download.
PARA COMENZAR
BÚSQUEDA DE CANALES INICIAL
Antes de continuar, asegúrese de conectar
correctamente su antena o conexión de TV por
cable y todos los dispositivos a su HDTV.
CONECTE EL CABLE DE CORRIENTE
120V AC, 60Hz
PANTALLA INICIAL DE MODO DE
AHORRO DE ENERGÍA
ENCIENDA LA TV
Siga las instrucciones en pantalla para elegir
el Modo de Ahorro de Energía y realizar la
Búsqueda Inicial de Canales/Señales.
ELEGIR DÓNDE SE USARA LA HDTV
Seleccione “Home Mode” al presionar la tecla CHM
para establecer el nivel de brillo de las lámparas a un
nivel de Energy Star, o seleccione “Store Mode” al pre-
sionar CHL para establecer el brillo de las lámparas a
uno adecuado para mostrador de exhibición.
PANTALLA DE CONFIGURACIÓN INICIAL
DE BÚSQUEDA DE CANALES
BÚSQUEDA DE CANALES Y SEÑALES:
Presione la tecla CHLM para realizar una
búsqueda de canales de una Antena o una
conexión directa de Cable, y una búsqueda
de señales de dispositivos conectados a las
entradas de la HDTV.
AYUDA EN PANTALLA (OPCIONAL)
Presione la tecla CHM si desea accesar una
guía de ayuda en pantalla.
NOTA: Este menú de ayuda en pantalla también es
accesible desde el menú principal.
PANTALLA DE AVANCE DE BÚSQUEDA
PANTALLA DE LISTADO DE CANALES Y SEÑALES
La última pantalla de configuración despliega cuantos
canales análogos y digitales se hayaron, así como
entradas de video detectadas. Presionar la tecla CHLM
finaliza el proceso de configuración.
NOTA: Para repetir el proceso puede presionar VOLM
SELECCIÓN DE ENTRADA AV
Presione la tecla INPUT para elegir la entrada
de video correcta que desee.
PANTALLA DE LISTADO DE
CANALES Y SEÑALES
¿Necesita ayuda?
1-877-864-9604
28
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERACIÓN DEL CONTROL REMOTO
• Tecla INPUT—Elegir la entrada de video desea-
• Tecla POWER—Prende o apaga su HDTV.
da Mantenga presionada la tecla para mostrar
el menú de entradas.
• Tecla ECO—Modifica el nivel del Ahorrador de
Energía (ver página 32)
–
• Tecla de volumen VOL
minuir el nivel del volumen.
—Aumentar o dis-
+
• Tecla AUDIO—Selecciona el tipo de audio,
Estéreo, Mono, o SAP (de estar disponible).
• Teclas de canal CH L M —Navegar los canales
en la base de datos de la memoria.
• Tecla ON TIMER—Despliega la hora de encendi-
do automático (ver Reloj Temporizador en la
página 33).
• Tecla MUTE—Cancelar o restaurar el audio.
• Tecla RECALL—Cambiar entre el canal actual y
el último accesado.
• Tecla CAPTION—Elegir entre los diferentes
modos de subtítulos digitales.
• Tecla NET@—Selecciona directamente la entra-
da Net y despliega la pantalla inicial de Internet.
• Tecla RESET—Presione dos veces seguidas para
restaurar la TV a configuraciones de fábrica. Se
borrarán las modificaciones del usuario.
• Tecla HDMI—Selecciona directamente las
entradas de HDMI 1, 2 y 3.
• Tecla SLEEP—Despelgar el reloj de apagado.
Mientras el reloj se encuentre en pantalla, pre-
sione la tecla “0” para establecer el tiempo (en
incrementos de 30 minutos) al cual se apagará
automáticamente la HDTV.
• Tecla USB—Selecciona directamente la entrada
de USB.
• Tecla MENU—Mostrar el menú en pantalla.
• Tecla PIX SHAPE—Elegir entre las relaciones de
aspecto disponibles. Las diferentes configura-
ciones estiran, agrandan o llenan la imagen en
la pantalla. Pueden aparecer en pantalla barras
en la parte superior e inferior, o lado izquierdo
y derecho, dependiendo en la señal o programa
transmitido.
• Tecla HELP—Despliega en pantalla el menú de
ayuda.
• Tecla LiNKS—Despliega los widgets dispo-
nibles. Funciona como telca “Home” al navegar
la entrada Net.
• Tecla EXIT—Salir del menú en pantalla.
NOTE: Pix6-7 están configurados como Pix1-2 de
modo PC. El utilizar Pix6-7 in TV en modo de
TV no es recomendado.
• Teclas Cursor L (arriba) M (abajo)—Mover el
cursor en pantalla hacia arriba y abajo.
• Teclas Cursor ꢀ (izq.) ꢁ (der.)—Mover el cursor
en pantalla hacia la izquierda y derecha.
• Tecla INFO—Desplegar el banner de informa-
ción de canal.
• Tecla ENTER—Ejecutar la opción seleccionada
en pantalla.
• Teclas NUMÉRICAS—Elegir canales directa-
mente.
Las teclas PLAY, PAUSE, STOP, REW, FF, W, T,
CAMERA, y XACTI MENU controlan funciones de
reproducción en una cámara digital Xacti de
Sanyo al estar activada la función de HDMI-CEC
tanto en la cámara como la HDTV (ver Enlace
HDMI en la página 31).
NOTA: Para canales mayores al 99, mantenga presion-
ado el primer número, suéltelo y presione los dos
números restantes.
• Tecla “–” (sub ch)—Permite la selección directa
de canales y subcanales digitales. Por ejemplo:
para sintonizar el canal 39.1, presione la tecla 3,
9, –, y 1 en orden sucesivo.
NOTA: Estas teclas de reproducción pueden reaccionar o
no con otros aparatos aparte de la cámara Xacti.
¿Necesita ayuda?
1-877-864-9604
29
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERACIÓN DEL MENÚ EN PANTALLA
CANAL / ENTRADA __________
Despliegue el menú en pantalla. Utilice las
teclas CURSOR LM para seleccionar Canal /
Entrada. Presione ENTER.
Búsqueda de canales
Auto – Busca en el modo detectado, Cable o Aire.
Cable – Busca canales análogos y canales digitales de
Cable no codificados.
PANTALLA DE MENÚ PRINCIPAL
Aire (Antena) – Busca canales análogos y digitales de
transmisión aérea.
Adición digital – Busca canales digitales de trans-
misión aérea, agregando canales recientemente
encontrados a la base de datos de canales.
NOTA: La función de Adición Digital Aérea no es disponible
si el modo de TV es Cable.
Memoria de Canales
Esta función enlista todos los canales encontrados,
análogos y digitales. También muestra canales
Análogos que no se hallaron y pueden ser agregados.
PANTALLA DE ESTABLECER CANALES
Use el CURSOR LM para mover la barra de selección
por todos los canales habilitados y deshabilitados, o
use la tecla CH LM para saltarse los deshabilitados.
Presione ENTER para habilitar (marcar) o deshabilitar
(desmarcar) el canal seleccionado.
NOTA: Para información sobre canales digitales locales, visite
INFO. IMPORTANTE: Esta HDTV mantiene una sola base de datos
para canales digitales. Por lo tanto cuando busque canales de
Cable, la base de datos de canales digitales será borrada. Usted
sólo podrá recibir aquellos canales ClearQAM (decodificados)
provistos por su compañía de cable.
PANTALLA DE MEMORIA DE CANALES
Establecer entradas
Esta función permite quitar del ciclo de entradas
(INPUT) aquellas que no se estén utilizando.
Use el CURSOR LM para elegir una entrada. Presione
ENTER para habilitar (marcar) or deshabilitar (desmar-
car) la entrada seleccionada.
NOTA: Al menos una entrada debe quedar habilitada.
:Saltar es sólo como referencia.
PANTALLA DE CONFIGURACIÓN DE ENTRADAS
¿Necesita ayuda?
1-877-864-9604
30
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERACIÓN DEL MENÚ EN PANTALLA
Configuración de Video 3
Utilice esta función para establecer una conexión ya
sea Componente o Compuesta a la entrada de VIDEO
INPUT 3 en su HDTV.
Use el CURSOR LM para seleccionar el tipo de
conexión que será usada en la entrada Video3.
Presione ENTER, aparecerá una marca azul junto a la
opción seleccionada.
PANTALLA DE CONFIG. DE VIDEO 3
Enlace HDMI
NOTA: Diseñado para utilizarse con una cámara digital Xacti
de Video/Película marca Sanyo y puede no activar
todas las funciones HDMI-CEC de otros equipos.
Utilice la Función HDMI-CEC para habilitar
y
deshabilitar funciones CEC disponibles.
Encendido Sinc. HDMI y Apagado Sinc. HDMI
habilitan funciones específicas como el proceso
automático de encendido y apagado.
PANTALLA DE ENLACE HDMI
Xacti-LINK
Con una cámara digital Xacti de
Video/Película marca Sanyo conectada a
la entrada HDMI de la HDTV, el confi-
gurar la Función HDMI-CEC a Encendido,
habilita el uso de las teclas del control
remoto GXEB para operar la cámara.
NOTA: La función HDMI-CEC de la cámara Xacti también
debe ser encendida para habilitar el Xacti-Link.
¿Necesita ayuda?
1-877-864-9604
31
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERACIÓN DEL MENÚ EN PANTALLA
CONFIGURACIÓN ___________
Despliegue el menú en pantalla. Use las teclas
CURSOR LM para seleccionar Configuración.
Presione ENTER.
Lenguaje del Menú
Elija entre el idioma inglés, español o francés para
desplegar el menú en pantalla.
• English
PANTALLA DE MENÚ PRINCIPAL
• Español
• Français
Presione ENTER en el idioma deseado.
Subtítulos Digitales
Los Subtítulos Digitales son información de texto
oculta, transmitida junto con la imagen y sonido. El
activar la función (al presionar la tecla CAPTION al ver
televisión), la HDTV abre e interpreta esta información
(digital o análoga) y sobreimpone los textos en pantalla.
PANTALLA DE MENÚ DEL LENGUAJE
NOTA: Las transmisoras locales deciden que información
transmitir.
Use el CURSOR LM y ꢀ ꢁ para modificar la letra, el
fondo y el primer plano de los subtítulos digitales.
Configuración de Energía
Utilice las funciones de Ahorrador de Energía y Sensor
de luz dentro del menú de Configuración de Energía
para controlar el brillo de las lámparas del panel para
reducir el consumo de energía.
PANTALLA DE CONFIGURACIÓN DE
SUBTÍTULOS DIGITALES
Ahorrador de Energía – Controla el brillo del panel
para reducir el consumo de energía.
• Nivel 1: Ahorrador de Energía apagado.
• Nivel 2: Bajo consumo de energía.
• Nivel 3: Consumo de energía aún más bajo.
Presione ENTER en el nivel deseado.
NOTA: La tecla ECO también puede ser utilizada para modificar
los valores sin entrar al menú.
PANTALLA DE AHORRADOR
DE ENERGÍA
¿Necesita ayuda?
1-877-864-9604
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Sensor de luz – Detecta la intensidad de luz ambiental
del cuarto y controla los parámetros de brillo e
imagen para reducir el consumo de energía de la TV.
NOTA: Cuando la habitación esté oscura, el brillo del panel y/o
los parámetros de imagen tales como brillo y contraste
son reducidos. Cuando la habitación es más iluminada,
los parámetros se afectan de manera contraria.
PANTALLA DE SENSOR DE LUZ
Reloj Temporizador
Esta función permite establecer la Hora Actual en su
HDTV y habilitar una Hora de Encendido para que el
televisor se prenda a determinada hora.
Cuando la Función de encendido se habilita, la TV
automáticamente se encenderá a la hora establecida.
PANTALLA DE RELOJ TEMPORIZADOR
Motion Sync. (120 Hz)
Su HDTV desplegará todas las señales a
una frecuencia de barrido de 120Hz.
Motion Sync es una función especial de
Conversión de Cuadros por Segundo
que ayuda a eliminar imágenes borrosas
y distorsión, debidos al movimiento y las
escencas de acción rápida.
Encendido – Aprovecha totalmente las capacidades
de frecuencia de barrido de la TV para la
mejor imagen.
PANTALLA DE MOTION SYNC.
Apagado – Deshabilita la función de Motion Sync.
¿Necesita ayuda?
1-877-864-9604
33
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERACIÓN DEL MENÚ EN PANTALLA
CONFIGURACIÓN ___________
V – Chip (Control paternal)
Utilice esta función para bloquear automáticamente
programación con contenido que crea inapropiado
para ser visto por sus hijos.
NOTA: Esta función está diseñada para cumplir con regula-
ciones de la FCC para V-Chip en los Estados Unidos
de América. Esta función pudiera no activarse con
señales que originen de otros países.
PANTALLA DE CONFIGURACIÓN/V-CHIP
ADJUSTING THE V-CHIP SETTINGS
Elija Encendido y presione ENTER.
Elija Ajustar y presione ENTER.
Utilice las teclas de CURSOR L M y ꢀ ꢁ para nave-
gar y la tecla ENTER para Bloquear o Desbloquear la
clasificación seleccionada. Aparecerá a un lado de la
clasificación el símbolo de un candado indicando que
está bloqueada.
NOTA: Bloquear una clasificación bloqueará todas las clasifi-
caciones más altas. Desbloquear una clasificación,
desbloqueará todas las más bajas.
PANTALLA DE AJUSTAR (ESTÁNDAR)
SISTEMA AVANZADO V-CHIP (RRT5)
RRT5 (V-chip Regional Ratings 5) es un sistema avan-
zado de clasificación regional para canales digitales
recibidos desde una antena.
Cuando la HDTV detecta datos RRT5 compatibles, se
descargan y almacenan en memoria, entonces la pan-
talla de configuración V-Chip es modificada para
mostrar la opción de Ajustar (Avanzado).
La pantalla de Configuración/V-Chip se modifica para
mostrar la opción de Ajustar (avanzado).
Utilice las teclas CURSOR LM y ꢀ ꢁ para seleccionar
las diferentes opciones. Use ENTER para bloquear o
desbloquear la clasificación seleccionada.
NOTA:Puede haber más clasificaciones de las que se ven en
pantalla. Cuando aparezcan barras verticales, presione
CURSOR LM para accesar clasificaciones adicionales.
MÁS INFORMACIÓN
Puede consultar información adicional sobre las
clasificaciones V-Chip y MPAA en las páginas:
PANTALLAS DE AJUSTAR (AVANZADO)
¿Necesita ayuda?
1-877-864-9604
34
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERACIÓN DEL MENÚ EN PANTALLA
IMAGEN ____________________
Despliegue el menú en pantalla. Utilice las
teclas CURSOR LM para seleccionar Imagen.
Presione ENTER.
Puede elegir entre Intenso, Moderado y Estándar, los
cuales tienen valores fijos y predeterminados para los
diferentes parámetros.
O puede elegir la opción de Manual para ingresar
valores personalizados.
PANTALLA DE MENÚ PRINCIPAL
NOTA: Cada entrada de AV puede tener su propio modo de
imagen (predeterminado o manual). La opción selec-
cionada es indicada por una marca azul.
CONFIGURACIÓN MANUAL DE IMAGEN
Parámetros de ajuste Manual:
Color
Brillo
Tinte
Contraste
•
•
•
•
•
•
Nitidez
Contraste Dinámico
PANTALLA DE IMAGEN
La opción de Configuración Detallada permite el ajuste
de 7 parámetros adicionales tales como:
Balanceo de señal
Balance de blanco
Reducción de ruido
Nitidez Vertical
Tamaño-H
•
•
•
•
•
•
•
Realce de orillas
Tamaño-V
NOTA: La opción de Valores originales regresa todos los
parámetros a sus niveles de fábrica.
AJUSTES A LOS PARÁMETROS DE IMAGEN
PANTALLA DE SELECCIÓN
DE PARÁMETROS
Utilice las teclas de CURSOR LM para seleccionar el
parámetro que desea ajustar. Presione la tecla ENTER
para accesar la pantalla de ajustes. Modifique los valores
del parámetro utilizando las teclas de CURSOR ꢀ ꢁ.
NOTA: Las teclas de CURSOR LM seleccionan al siguiente
o previo parámetro sin regresar a la pantalla anterior.
Una vez terminados los ajustes, presione la tecla EXIT
para salir del menú.
EJEMPLOS DE PANTALLA DE
AJUSTE DE PARÁMETROS
¿Necesita ayuda?
1-877-864-9604
35
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERACIÓN DEL MENÚ EN PANTALLA
SONIDO ____________________
Despliegue el menú en pantalla. Utilice las
teclas CURSOR LM para seleccionar Sonido.
Presione ENTER.
Elija una opción para su configuración de sonido:
Auto – Utiliza valores predeterminados de acuerdo al
modo actual de Imagen.
Dinámico, Tenue, Estándar – Valores predeterminados
para el sonido no ligados a las opciones de imagen.
PANTALLA DE MENÚ PRINCIPAL
CONFIGURACIÓN MANUAL DE SONIDO
La opción de Manual incluye varios parámetros que
pueden ser ajustados personalmente:
Graves
Agudos
Configuración Detallada
•
•
•
– Ecualizador de 4 bandas: Personalice el espectro de
graves y agudos.
NOTA: La opción de Valores Originales regresa todos los
parámetros a su configuración original de fábrica.
PANTALLA DE PARÁMETROS MANUALES
AJUSTES A LOS PARÁMETROS DE SONIDO
Utilice las teclas de CURSOR LM para seleccionar el
parámetro que desea ajustar. Presione la tecla ENTER
para accesar la pantalla de ajustes. Modifique los valores
del parámetro utilizando las teclas de CURSOR ꢀ ꢁ.
NOTA: Las teclas de CURSOR LM seleccionan al siguiente
PANTALLA DE PARÁMETROS
MANUAL (AVANZADO)
o previo parámetro sin regresar a la pantalla anterior.
Una vez terminados los ajustes, presione la tecla EXIT
para salir del menú.
EJEMPLOS DE PANTALLA DE
AJUSTE DE PARÁMETROS
¿Necesita ayuda?
1-877-864-9604
36
Download from Www.Somanuals.com. All Manuals Search And Download.
CONEXIONES Y CONFIGURACION DE PC
Utilice su HDTV como monitor de computadora,
conectando su televisor a su PC o Laptop por
medio de un cable de monitor apropiado.
Configuración de PC
Auto Ajuste – Ajuste automático de posición de la
imagen, dot clock y fase.
Antes de conectar algún cable, desenchufe de
la toma AC los cables de corriente tanto de la
HDTV como de la PC.
Dot Clock – Ajusta la Frecuencia de Barrido para
igualarla a la de su PC.
Encienda la HDTV y cualquier otro equipo
externo antes de encender la computadora.
Fase – Ajuste la Fase cuando la imagen aparenta
vibrar o estar borrosa.
Para evitar una condición “Fuera de Rango”,
establezca la resolución de video de su PC a una
resolución compatible con la HDTV. Ver pág. 22.
Posición-H – Mueva la imagen horizontalmente.
Posición-V – Mueva la imagen verticalmente.
Ahorro de energía – Habilita a la HDTV entrar en
modo de espera mientras la PC no se utilice.
NOTA: Si la PC sólo cuenta con salida DVI, un adapta-
dor DVI a RGB será requerido, o un cable DVI a
HDMI y unos cables RCA de audio (ver entrada
HDMI (DVI) INPUT1 en pág 26).
SALIDA
ANÁLOGA RGB
SALIDA
DIGITAL DVI
P
PANTALLA DE
CONFIGURACIÓN PC
Imagen y Audio PC
Estándar – Aplica valores predeterminados a los
parámetros de Imagen y Audio.
Manual – Ajuste los parámetros de Contraste,
Brillo y Temperatura de color de la pantalla, y los
Graves y Agudos del audio.
Pantalla Laptop
Si utiliza su HDTV Sanyo para desplegar las
imágenes en pantalla de una laptop, el mantener
presionada la tecla Fn (o FN) mientras pesiona la
tecla de función (F5, F7, F8, etc.) apropiada deberá
ciclar los modos de despliegue entre la laptop y la
HDTV.
Los modos pueden incluir el desplegar la imagen
sólo en la laptop, tanto en la laptop como la
HDTV, o desplegar sólo en la HDTV.
Sostenga
y presione
PANTALLAS DE IMAGEN Y AUDIO (MANUAL)
NOTA: Los símbolos de las teclas Fn y de función en el
teclado de la laptop pueden variar entre una
marca y otra.
NOTA: Estos parámetros no afectan los de TV normal.
¿Necesita ayuda?
1-877-864-9604
37
Download from Www.Somanuals.com. All Manuals Search And Download.
ENTRADA USB
REPRODUCTOR DE IMÁGENES
Despliegue fotos en su HDTV con el uso de un
dispositivo de memoria USB.
Se pueden utilizar cualquiera de las dos entradas USB
en el panel lateral de la HDTV.
NOTA: Al conectar dos dispositivos, sólo el primero en conec-
tarse será reconocido y habilitado.
PANTALLA DE VISTAS EN MINIATURA
MEMORIA
USB
NOTA: Aparecerá un ícono “tapando” la vista en
miniatura si una foto no puede ser decodi-
ficada o no contiene datos de vista previa.
NOTA: La HDTV se cambia a la
entrada USB cuando se
detecta una memoria en el
puerto USB.
FUNCIONAMIENTO
Presione ENTER sobre una foto en vista miniatura
para abrir las funciones de Rotar, Vista completa y Ver
presentación.
Una vez en Vista completa:
Use las teclas CURSOR ꢀ ꢁ para cambiar de foto.
Presione ENTER para mostrar el menú de opciones.
AJUSTES A
PRESENTACIÓN
MENÚ DE OPCIONES
EN VISTA COMPLETA
PRESENTACIÓN DE DIAPOSITIVAS
En el menú de Configuración puede habilitar o
deshabilitar las funciones de Aleatorio y Cambio rápido.
Presione ENTER en Ver presentación desde la pantalla
de vistas en miniatura o desde el menú de opciones en
vista completa para comenzar la presentación desde la
imagen seleccionada.
MENÚ DEL REPRODUCTOR
Presione MENU al estar en vista completa o en una
presentación de diapositivas para desplegar el menú.
Ajustes de imagen – Ajuste Color, Tinte, Contraste,
Brillo, Nitidez y Contraste Dinámico.
NOTA: Ajustes de imagen son configuraciones separadas a
las de TV y entradas AV.
PANTALLA DE MENÚ USB
¿Necesita ayuda?
1-877-864-9604
38
Download from Www.Somanuals.com. All Manuals Search And Download.
GARANTÍA LIMITADA DE UN AÑO EN PARTES Y MANO DE OBRA
ESTA GARANTÍA LIMITADA DE PARTES Y MANO DE OBRA ES VÁLIDA SÓLO EN TELEVISORES SANYO COMPRADOS
Y USADOS EN LOS ESTADOS UNIDOS DE AMÉRICA, CANADÁ Y PUERTO RICO, EXCLUYENDO CUALQUIER OTRO
TERRITORIO Y PROTECTORADO DE E.E.U.U. ESTA GARANTÍA LIMITADA APLICA SÓLO A COMPRADORES
MINORISTAS Y NO APLICA A PRODUCTOS UTILIZADOS CON FINES COMERCIALES O INDUSTRIALES.
APLICACIÓN DE LA GARANTÍA
POR UN AÑO, desde la fecha de la compra original, Sanyo Manufacturing Corporation (SMC) garantiza esta televisión
de estar libre de defectos de manufactura en materiales y mano de obra bajo uso y condiciones normales para partes
y trabajo.
Por los PRIMEROS 90 DÍAS, desde la fecha de la compra original, Sanyo Manufacturing Corporation remplazará
cualquier televisión defectuosa vía el vendedor original. Para asegurar la apropiada aplicación de la garantía,
conserve el recibo original de compra fechado como evidencia de compra. Regrese la TV defectuosa al vendedor
junto con su recibo de compra además de todos los accesorios incluídos, como el control remoto. La TV defectuosa
será cambiada por una del mismo modelo, o un modelo equivalente o de igual valor, si es necesario. El reemplazo
de la TV será en contingencia y disponibilidad y a la exclusiva discreción de Sanyo Manufacturing Corporation.
ESTA GARANTÍA ES EXCLUYENTE DE Y EN LUGAR DE TODAS LAS OTRAS GARANTÍAS DE COMERCIALIZACIÓN O USO
PARA UN PROPÓSITO ESPECÍFICO.
OBLIGACIONES
Por un año, desde la fecha de la compra original, Sanyo Manufacturing Corporation (SMC) garantiza esta televisión
de estar libre de defectos de manufactura en materiales y mano de obra bajo condiciones normales de uso. Durante
los primeros 90 días bajo esta garantía para cualquier defecto de manufactura o mal funcionamiento Sanyo
Manufacturing Corporation proveerá una nueva TV vía intercambio con el vendedor.
CÓMO HACER UN RECLAMO BAJO ESTA GARANTÍA.
Por favor llame al 1-877-864-9604. Por favor esté preparado para darnos el número de modelo de la televisión cuan-
do llame. El número de modelo y el número de serie están impresos en la etiqueta agregada en la parte trasera
de la unidad.
Para asistencia al consumidor, llame sin costo al 1-877-864-9604
Horas de operación: Lunes a Viernes de 7:30 AM a 7:00 PM (horario del Centro)
Esta garantía expresa derechos contractuales específicos; minoristas podrán tener derechos estatutarios
adicionales que pueden variar de estado a estado.
(EFECTIVO: Marzo 1, 2007)
Su HDTV Sanyo es registrada al momento de la compra, por favor guarde su recibo de compra.
Para su protección en caso de robo o pérdida de este producto, por favor llene la siguiente
información requerida y GUÁRDELA en un lugar seguro para su registro personal:
No. de Modelo__________________________
Fecha de compra ___________________________
Precio de compra ___________________________
Lugar de compra ___________________________
No. de Serie ____________________________
(Localizado en la parte posterior de la TV)
Sanyo Manufacturing Corp.
3333 Sanyo Road, Forrest City, AR 72335
¿Necesita ayuda?
1-877-864-9604
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|