WEB
WEB
TRANSMITTER
SNS-110 Owner's Manual
(Version 1.1)
4
2
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulation Approval
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interface in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
- Reorient of relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio TV technician for help.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Chapter 1. SNS-110 Overview - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6
Overview - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6
Functions and Feature - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6
Names and Function - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8
Chapter 2. Installing SNS-110 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 10
Setting Configuration - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 10
Cautions in Installation- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 11
Unpacking - - - - - - - - - - - - - -- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 14
Chapter 3. Connecting to Instruments - - - - - - - - - - - - - - - - -- - - - - - - - - - - - - - - 15
Connecting to Camera and Video Image Players - - - - - - - - - - - - - - - - - - - - -- - - - - - - 15
Connecting to External Instruments - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 16
Connecting to Network - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 17
Connecting to Alarm Sensors and External Devices - - - - - - - - - - - - - - - - - - - - - - - - - - 18
Connecting to PAN/TILT/ZOOM/FOCUS Camera Controller- - - - - - - - - - - - - - - - - - - - - 19
Connecting to RS-232C - - - - - - - - - - - - - - - -- - - - - - - - - - - - - - - - - - - - - - - - - - - - 20
Creating RS-232C Cable- - - - - - - - - - - - -- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 21
Terminal Emulation Communication Set-up- - - - - - - - - - - - -- - - - - - - - - - - - - - - - - - - 21
Creating Ethernet Cable - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 22
Chapter 4. Setting an IP Address - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 23
Before You Begin - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -23
Setting in Ethernet - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 24
Setting in Unix - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 26
Setting with IP Installer - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
28
Setting Other Network Information - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 32
Changing IP Address - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 32
In Cable Network through Cable Modem - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -33
Chapter 5. SNS-110 Log-in - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 34
Ideal Specification - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 35
Log in through Netscape - - - - - - - - - - - - - - - -- - - - - - - - - - - - - - - - - - - - - - - - - - 34
Log in through Explorer - - - - - - - - - - - - - - - -- - - - - - - - - - - - - - - - - - - - - - - - - - - 35
Chapter 6. Application Mode (Video Image Monitoring Mode) - - - - - - - - - - - - - - -39
Initial Screen - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -39
Single Screen - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 39
Quadruplex Screen - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -40
Automatic Sequential Screen - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 40
Single Screen with PAN/TILT/ZOOM Controllers - - - - - - - - - - - - - - - -- - - - - - - - - - - - 41
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7. Administration Mode - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 42
Initial Screen - - - - - - - - - - - - - - - -- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 42
Camera Set-up - - - - - - - - - - - - - - - -- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 43
PAN/TILT/ZOOM Set-up - - - - - - - - - - - -- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 45
Quad/Sequential Set-up - - - - - - - - - - - - - - - -- - - - - - - - - - - - - - - - - - - - - - - - - - -46
Web Transmitter Set-up - - - - - - - - - - - - - - - -- - - - - - - - - - - - - - - - - - - - - - - - - - - 47
Alarm/Relay Set-up - - - - - - - - - - - - - - - -- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 50
Network Set-up - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 52
File Transter Set-up - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 55
Custom User Interface Set-up - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 57
ABOUT/SUPPORT/HELP - - - - - - - - - - - - - - - -- - - - - - - - - - - - - - - - - - - - - - - - - 58
?
Appendix A - - - - - - - - - - - -- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -60
SNS-110 Specifications - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -61
Appendix B - - - - - - - - - - - -- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -64
Factory Default - - - - - - - - - - - -- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 65
Appendix C - - - - - - - - - - - -- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -67
How to use Console - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 68
Appendix D - - - - - - - - - - - -- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -77
Dynamic IP Information Transfer - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 78
Appendix E - - - - - - - - - - - -- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -84
FAQ - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 85
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 SNS-110 Overview
Overview
SNS-110, connected to surveillance cameras or other external devices, compresses video image as
motion JPEG through zip algorithm and transmits it to a remote party through network (Ethernet, cable
modem).
SNS-110 may be connected to maximum of 4 video images and concurrently transmits the image in a
form of single screen, quadruplex screen, or automatic sequential screen.
Also, this system provides remote users in the Internet with alarm processing function and remote control
on PAN/TILT/ZOOM/FOCUS, succeeding in an extensive range of applications.
Functions and Features
● This system transmits real time images at any time with the network (Ethernet, cable modem) present.
● Users in the Internet are not required of additional S/W installation to receive the concurrent video
images, but may Log-in simply by accessing SNS-110 IP address with the existing web browser (such
as Netscape or Explorer).
● Users may select a type of screen, among Single Screen, Quadruplex Screen, and Automatic
Sequential Screen, and also may choose, at his or her preference, transmitting speed and resolution.
"Automatic Sequential" Screen provides the sequential and automatic changes in
size of the input images, depending on how the user has set up.
● This system transmits the image to the registered e-mail address at a particular point of time, by
setting up the alarm.
● Users may conveniently remote-control PAN/TILT/ZOOM/FOCUS under RS485 connection.
● Although the transmitted images are not locked in any way, users may set up ID and access
password.
● This system is usable regardless of the region because the image broadcasting system (NTSC/PAL) is
detected and operated with autornatic recognition.
● Auto terminal resistance function automatically withdraws the terminal resistance of 75Ω with the video
loop (loop through) connection.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
● You can send video image files through FTP server at certain time or in regular intervals. Users can
access the FTP server and search the saved video files.
● You can change the LOGO image on SNS-110 screen, or background color or font colors.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Names and Function
Familiarize yourself with the names and function of each part on the front and back panels, before
installing SNS-110.
Front View of SNS-110
1
3 4 5 6
3
4
1.CONTROL 2.F/H 3.Tx R 4.Rx
R
7
8
9
10
2
Name
Function
Receives input from maximum of 4 video image signals.
①
Video In
Transmit the image output to cameras or other external video-imaging devices
When connected, the terminal resistance of 75 is automatically seized.
②
Video Out
(Loop Through Out)
❈
Ω
Off : when using as console purpose with RS-232C port connected to a PC
On : when RS-232C is to be connected to an External Modem.
③
Control S/W
❈The current version does not support connecting an External Modem.
Off : use the RS-485 on the reverse side as Half Duplex
On : use the RS-485 on the reverse side as Full Duplex TX mode
④
F H (S/W)
Off : Tx Termination resistance 120 Ω off
⑤
⑥
Tx R (S/W)
Rx R (S/W)
On : Tx Termination resistance 120 Ω on
Off : Rx Termination resistance 120 Ω off
On : Rx Termination resistance 120 Ω on
⑦
⑧
Network LED
Power LED
Preset Button
Reset Button
Blinks when sending or receiving data with the proper connection.
Indicates the power on/off.
Returns to the initial set-up environment of factory default
Restarts SNS-110 without turning off the power.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear of SNS-110
DC 5V
ETHERNET
RS-232C
R/O RX
TX
ALARM IN
RA RC
1 2
G
3 4
G
- + - +
1
4
2
3
5
6
Name
Function
Sensor Input : 1,2,3,4
Signal GND : G
①
②
Alarm Input(1,2,3,4)
Connects to maximum of 4 alarm sensors.
Connected to the external device for remote control
R/O (Relay Out)
RA
RC
Connects to RS-485 cable and remotely regulate
PAN / TILT / ZOOM/ FOCUS
controllers.
Full Duplex : use RX and TX.
Half Duplex : use TX .
RX(+,-)
TX(+,-)
③
④
RS-485(+,-)
RS-232C
Connects to console and an external modem through
the RS-232C cable connection.
❈You are recommended to use the RS-232C
cable packed with this
SNS-110.
❈The current version does not support
connecting an External Modem.
9Pin DSub Connector
RJ-45 Connector
Connects to Ethernet (10BaseT/110BaseT) and cable
modem network.
⑤
⑥
Network Port
Power In
Supplies the power to SNS-110 with a DC 5V input
terminal
❈Only use the compatible adapter enclosed in
the SNS-110 package and supply DC 5V.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Installing SNS-110
Preparation and installation of SNS-110
Setting Configuration
Please, familiarize yourself of the safe condition of SNS-110 installation.
This product must be horizontally stabilized and not be sloped or vertically positioned. Positioning and
properly centering its wiring room are crucial for its aptitude function. If the devices are too near with each
other, or if the ventilation is not sufficient, it may trigger the system malfunction and make its maintenance
as well as repair difficult to achieve.
The place must be well ventilated and the case cover must be firmly attached together to avoid system
malfunction or system shutdown by external factors. Certain inner parts are extremely susceptible to
abnormal environment, therefore do not open the case.
SNS-110 must be kept in the place with constant temperature and humidity as indicated below.
● Operation Temperature : 0oC ~ 40oC
● Storage Temperature : -20oC ~ 60oC
● Operation Humidity : 20% ~ 85% RH
● Storage Humidity : 20 ~ 85% RH
● Input Voltage: DC 5V
Adapter Input Voltage (AC 110 ~ 240V, 50 / 60Hz, 0.5A)
Adapter Output Voltage (DC +V, 3A)
● Power Consumption : 12 W or below
Caution
The fluctuation of operation voltage must be within 10% of the regulation
voltage, and the electric outlet must be always grounded. Electric heat
devices, such as, hair dryers, irons, refrigerators, etc., must not be co-used in
the same outlet with SNS-110. AVR is recommended for stable power supply.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Cautions in Installation
Be aware of the following cautions when installing SNS-110.
● Always turn the power off before SNS-110 installation.
● Severe impact or vibration may cause malfunction.
● Avoid places with strong magnetic or electric field, or places near a radio or TV.
● Always keep the place dust-free when installing or moving SNS-110.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
15Cm
● Position it in an open space with flat surface, keeping the
aptitude temperature.
Also, maintain the clearance between back of the main body and the wall.
● Be careful not to insert accidentally any conducting material
in the ventilation space of product.
● Turn the power off and disengage the power cord from the body,
when changing the circuit-protecting fuse.
● Avoid a direct ray of light, and keep the safe distance between
crowded place and the product as well as its assemblies.
● The bottom surface must be moisture-free.
And, be cautious about any possible delicate factors,
such as ungrounded extension cable, abraded power cord,
lack of safe grounding.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
● Do not neglect fumes or unusual odor, which may be symptoms of malfunction.
When these are identified, please instantly disconnect the power
and consult to an expert from your local service center.
NOTE
Always use a dry cloth when cleaning this product. If the contamination is
serious, please wipe it first with a neutral detergent, then with a dry cloth.
Avoid using volatile material, such as alcohol, benzene, or sinner, when wiping
the surface, due to potential damage on the surface.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking
When you purchase SNS-110, after removing the wrap, place the product on a flat surface or where you
will be installing it.
Then, check if there is any missing part among the following items.
● SNS-110 Main Body
● User’s Guide
● Power Adapter (1EA)
● Power Cord (1EA)
● RS-232C Cable (1EA)
4
2
1
SNS-110 Main Body
User’s Guide
RS-232C Cable (1EA)
Power Adapter (1EA)
Power Cord (1EA)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3. Connecting to Instruments
You may connect the following items with SNS-110, such as video image players (e.g., VTR, DVDP, etc.,),
network devices, alarm sensors, PAN/TILT/ZOOM/FOCUS controllers, and PC-connected consoles.
No voltage, more than DC 2V, must be connected to the video in/output
terminal 1~4.
Caution
Connecting to Camera and Video Image Players (e.g., VTR, DVDP, TV)
VTR, DVDP, TV
OUT
CAMERA
3
4
1.CONTROL 2.F/H 3.Tx R 4.Rx
R
SNS-110 automatically detects NTSC/PAL and transmits it as image signal. Therefore, you may connect
cameras and video image players (e.g., VTR, DVDP, etc.,) to video terminal 1~4.
Caution
Video image players are preferred with identical system when connecting to
Video In/Out 1~4. The miscellaneous usage may decrease the resolution of
certain broadcasting system.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to External Instruments
VTR, DVDP, TV
OUT
CAMERA
3
4
1.CONTROL 2.F/H 3.Tx R 4.Rx
R
VIDEO IN
External Device
SNS-110 produces the video image signal of the corresponding channel, if connected with external
instruments to Video Out 1~4 (loop through BNC). The terminal resistance of 75Ω will be automatically
seized by the connection with external instruments.
External Device
Surveillance control units : Frame Switcher, Quad Switcher, Sequential Switcher, Multi-plexer, Monitor, etc.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to Network
Ethernet(10BaseT/100BaseT)
DC 5V
ETHERNET
RS-232C
ALARM IN
R/O RX TX
1
2
G
3
4
G
RA
RC
-
+
-
+
RJ- 45 Ethernet Cable(Direct)
HUB
INTERNET
Back Bone
Cable Modem
DC 5V
ETHERNET
RS-232C
ALARM IN
R/O RX TX
1
2
0
3
4
0
RA
RC
-
+
-
+
RJ- 45 Ethernet Cable(Direct)
Cable Modem
Cable Network
INTERNET
Back Bone
CMTS
(Cable Modem Termination System)
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to Alarm Sensors and External Devices
ALARM IN
R/O RX
TX
RA RC
- + - +
1 2
G
3 4
G
S
S
S
E
N
S
O
R
3
S
G
N
D
G
N
D
E E
N N
E
N
S
S
S
O O
R R
O
R
4
1
2
Function
Alarm In
Name
Regular Capacity
Alarm 1/2/3/4/G
-TTL Level(5VDC)
-Initial Contact Resistance, Max. : 75m§
-Max. Switching Power : 60W, 62.5VA
-Max. Switching Voltage : 220VDC/125VAC
-Max. Carrying Current : 2A
Relay Out
RA/RC
-Contact Rating(Resistive) : 2A 30VDC/0.5A 125VAC
Alarm sensors and external devices are usable by connecting to ALARM IN and R/O terminals of the reverse
side of the SNS-110 respectively.
Caution
When connecting an external device to R/O terminal, you are recommended to use
additional “Relay” for the purpose of the protection of each device.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to PAN/TILT/ZOOM/FOCUS Controller
RX-
RX+
P/T/Z/F Controller 1
P/T/Z/F Controller 2
R/O
ALARM IN
RX TX
RX-
RA RC
1 2
G
3 4
G
- + - +
RX+
RX-
RX+
P/T/Z/F Controller 3
P/T/Z/F Controller 4
RX-
RX+
The RX/TX terminal of the reverse side of the SNS-110 uses the RS-442/485 interface and
PAN/TILT/ZOOM/FOCUS controllers can be connected to the terminal.
The PAN/TILT/ZOOM/FOCUS controllers that are supported are the following.
● Samsung Smart-Dome Camera (SCC-641) ● Pelco : Pelco-P Protocol Support Control
● Sungjin Electronic Communications : CPU-Receiver
When connecting Samsung Smart-Dome Camera (SCC-641), you have to connect the
SNS-110 to the TxDt, - terminals of SCC-641. In this case, the supportable Baud Rate
Note
is 38400 and 19200bps. For more detail information, please refer to the user manual
of SCC-641.
Reference inquire the shop at which it was purchased for the products other
that the above PAN/TILT/ZOOM/FOCUS camera and controllers.
The TX+ and TX- of the terminal as shown in picture, is connected to the external terminal of the
PAN/TILT/ZOOM/FOCUS controller, and generally the external terminal has a +,- polarity indication so be
sure not to switch the polarity.
Set the F/H Switch to On (knob faced down) on the front side of the SNS-110.
Refer to the PAN/TILT/ZOOM/FOCUS controller manual and confirm & reset the following items.
● Baud Rate
● Data Bit
● Stop Bit
● Parity Bit
● Controller ID (be careful not to duplicate a different controller ID)
Caution
If several PAN/TILT/ZOOM/FOCUS controllers are used, they must be the same
models.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to RS-232C
When connecting PC serial port (COM1, COM2) through RS-232C from back of SNS-110, you may
select console mode of SNS-110 by using PC terminal emulation program (HyperTerminal).
Control S/W from the front panel must be positioned "OFF".
Caution
In the console mode, if you change the existing data improperly, the system
may result in serious problems.
Pin Number
Name
Direction
RS - 232C Terminal (D-Sub 9Pin)
1
2
3
4
5
6
7
8
9
NC
TxD(Transmit Data)
Output
Input
RxD(Receive Data)
NC
SG(Signal GND)
Power
NC
NC
NC
NC
RS - 232C Connecting to Cable
DC 5V
ETHERNET
RS-232C
ALARM IN
R/O RX TX
1
2
0
3
4
0
RA
RC
-
+
-
+
RS - 232C Cable
Terminal
Emulation
Program
Serial Port
(COM1, COM2)
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Creating RS-232C Cable
The RS-232C Cable is packed with SNS-110, and so you don’t need to make it .
The wiring diagram shown below is for your information.
9Pin Female to 25Pin Female
1
1
14
6
9
2
3
2
3
5
7
25
13
9Pin Female to 9Pin Female
1
6
2
1
2
3
6
9
3
9
5
5
Terminal Emulation Communication Set-up
Items
Contents
Baud Rate
Data Bit
38400 bps
8 Bit
Parity
None
Stop Bit
1 Bit
Flow Control
Data Code
None
ASCII
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Creating Ethernet Cable
Since the Ethernet Cable is not packed with SNS-110, the user has to purchase and use it .
Connected from SNS-110 to Hub (Direct Cable)
1
1
8
8
RJ - 45
RJ - 45
DC 5V
ETHERNET
RS-232C
ALARM IN
R/O RX TX
1
2
G
3
4
G
RA
RC
-
+
-
+
Direct
Ethernet Cable
Web Browser
HUB
INTERNET
Back Bone
Connected from SNS-110 to PC(Twisted Cable)
1
1
8
8
RJ - 45
RJ - 45
DC 5V
ETHERNET
RS-232C
ALARM IN
R/O RX TX
1
2
G
3
4
G
RA
RC
-
+
-
+
Twisted
Ethernet Cable
Web Browser
LAN Card
RJ-45 Port
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Setting an IP Address
No information upon network is set up except Ethernet address (MAC address) in factory defaults. You
must set up the IP address when installing.
Caution
Ethernet address (00-00-f0-XX-XX-XX) is recorded on the bottom of the
product at the time of purchase. Because it may be accidentally erased,
please duplicate the number and keep it somewhere else.
Before You Begin
(1) Confirm the Ethernet address (00-00-f0-XX-XX-XX) on the bottom of SNS-110. You must keep this
number for IP address set-up.
(2) Confirm the normal power supply of SNS-110.
(3) Confirm the proper connection with network.
When properly connected to network with Ethernet environment, the front network LED blinks.
(4) To use your SNS-110 under the Ethernet(10BaseT/100BaseT) environment, an unused IP address
must be assigned to SNS-110 from a network manager.
At this time, check the following network related information.
● IP Address
● Gateway
● Subnet Mask
● Domain Name
● DNS
(5) If you set up an IP address through DHCP server in network environment, and if SNS-110 is
properly connected to network, you will automatically be assigned with an IP address, gateway, and
subnet mask by turning the power on. Confirm this auto-assigned IP address from RS-232C
connected PC terminal emulation (HyperTerminal).
Please, refer to
"
Connecting to RS-232C
"
and APPENDIX C "How to Use Console".
Refer to the Appendix D, "Dynamic IP information Transfer" to send Dynamically Assigned IP
Address to the administration server.
(6) Set up an IP address, according to network environment as following.
You must appropriately set up an IP address abiding by your network environment.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting In Ethernet (10BaseT/100BaseT)
For Windows 95/98/ME/NT/2000/XP
(1) Open Dos window from network-connected PC with SNS-110.
(2) Execute "arp -s".
arp -s <SNS-110 IP Address> <SNS-110 Ethernet Address>
Example :
arp -s 168.219.15.250 00-00-f0-ff-a1-0a
(3) Confirm if the IP address completely agrees with Ethernet address as shown below by executing "arp -a".
arp -a
Example :
arp -a
Internet Address
168.219.15.249
168.219.15.250
Physical Address
00-00-f0-ff-a1-2b
00-00-f0-ff-a1-0a
Type
static
static
If does not completely agree after pursuing (2), delete the present IP address by executing "arp -d"
and repeat (2) and (3).
arp -d <SNS-110 IP Address>
Example :
arp -d 168.219.15.250
24
Download from Www.Somanuals.com. All Manuals Search And Download.
(4) Wait until you receive the normal response after executing "ping".
ping <SNS-110 IP Address> - 110 -n 20
You must enter it.
Example :
ping 168.219.15.250 - 110 -n 20
Pinging 168.219.15.250 with 32 bytes of data:
Request timed out.
Request timed out.
No Response
Request timed out.
Request timed out.
Reply from 168.219.15.250: bytes=110 time=1ms TTL=255
Reply from 168.219.15.250: bytes=110 time=1ms TTL=255
Reply from 168.219.15.250: bytes=110 time=1ms TTL=255
Reply from 168.219.15.250: bytes=110 time=1ms TTL=255
Reply from 168.219.15.250: bytes=110 time=1ms TTL=255
Reply from 168.219.15.250: bytes=110 time=1ms TTL=255
Normal
Response
(5) If you are getting no response, attempt 1~2 more times. If you are still not getting any response,
please refer to APPENDIX D "FAQ".
Caution
You must only use the PC within identical Gateway with IP address, when
setting up IP address in Ethernet.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting in Unix
(1) Execute the following instruction for network-connected Unix machines with SNS-110.
(2) Execute "rarp -s".
rarp -s <SNS-110 IP Address> <SNS-110 Ethernet Address>
Example :
rarp -s 168.219.15.250 00:00:f0:ff:a1:0a
(3) Confirm if the IP address completely agrees with Ethernet address as shown below by executing "rarp - a".
rarp -a
Example :
rarp -a
IP Address
HW Type
HW Address
168.219.15.249
168.219.15.250
10Mbps Ethernet
10Mbps Ethernet
00-00-f0-ff-a1-2b
00-00-f0-ff-a1-0a
If does not completely agree after pursuing (2), delete the present IP address by executing "rarp - d"
and repeat (2) and (3).
rarp -d <SNS-110 IP Address>
Example :
rarp -d 168.219.15.250
26
Download from Www.Somanuals.com. All Manuals Search And Download.
(4) See if you receive the normal response as shown below after executing
ping <SNS-110 IP Address>
"ping".
Example :
ping 168.219.15.250
PING 168.219.15.250 (168.219.15.250): 56 data bytes
64 bytes from 168.219.15.250: icmp_seq=0 ttl=255 time=1.1ms
64 bytes from 168.219.15.250: icmp_seq=0 ttl=255 time=1.1ms
64 bytes from 168.219.15.250: icmp_seq=0 ttl=255 time=1.1ms
64 bytes from 168.219.15.250: icmp_seq=0 ttl=255 time=1.1ms
64 bytes from 168.219.15.250: icmp_seq=0 ttl=255 time=1.1ms
64 bytes from 168.219.15.250: icmp_seq=0 ttl=255 time=1.1ms
●
●
●
^c
(5) If you do not get responses, type "Ctrl+C" to stop and try number (4) couple of more times to re-
execute. If you still do not get response, refer to the APPENDIX "D."
Caution
You must only use the PC within identical gateway with IP address, when
setting up an IP address in Ethernet.
For detailed information, refer to APPENDIX E. FAQ "No response to PING
when setting the IP address".
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting with IP Installer
The 'IP Installer' is an application program that supports easy setting of network parameters of SNS-110 such
as IP Address, Gateway, Subnet Mask and so on. Before executing the 'IP Installer', the SNS-110 should be
connected with PC through RS-232C cable. The 'IP Installer' works on Windows 95/98/ME/NT/2000/XP.
● Program Name of IP Installer : SetupWebTX_v11.exe
Note
You can download the 'SetupWebTX_v11.exe' at 'http://www.samsungelectronics.com'.
(1) Download the 'SetupWebTX_v11.exe' and install your PC.
(2) Connect SNS-110 with PC through RS-232C cable. Please refer to the 'Connecting to RS-232C' of
Chapter 3.
Caution
Please identify which serial port is assigned for the connection of SNS-110 among
COM1/COM2 of PC.
When connecting the SNS-110 with PC, use the RS-232C cable included in the package of
SNS-110.
You have to confirm the assigned serial port not to be used simultaneously by other devices
such as modem or mouse.
(3) When executing the 'IP Installer' after the installation, you will see the following window. Select the serial
port what you assigned for the connection of SNS-110, and then click the "OK" button.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
If the serial port which you select is being used by other device, you will see the following
window.
In this case, you have to stop the usage of serial port by other device or change the
connection of SNS-110 to other serial port.
(4) If the SNS-110 and PC is successfully connected through RS-232C cable, you will see the following
window.
(5) In obedience to the 'Comments' of the program, reset SNS-110 by pushing the 'RESET' button or by
turning off and on of SNS-110. Then, the present state of network parameters of SNS-110 will be
displayed.
If nothing is displayed in the program, check the serial connection of SNS-110 and PC, and then repeat
the above procedure.
Note
For more detail information of the network parameters, please refer to the 'Network Set-up' of
Chapter 7.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
(6) Set up or modify the network parameters, and then click the 'OK' button.
(7) If the setting of network parameters succeeds, you will see the following window.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
(8) After the setting of network parameters, the SNS-110 will automatically reboots.
If all of the network parameters are properly set, you can connect SNS-110 with Web Browser.
Note
If the 'success' message window does not appear even though you wait more than 10
seconds after clicking 'OK' button, stop the program by clinking 'Cancel' button. And then,
execute the "SetupWebTX_v11.exe' and follow above processes again.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Other Network Information
After successfully setting up the IP address in Ethernet, follow the next procedure to set up additional
network information.
After the previous procedure, you must set up the following information, confirmed by the network
manager, to connect to network successfully.
● Gateway
● Subnet Mask
● Domain Name
● DNS
(1) Open a web browser (Netscape or Explorer) from the network-connected PC or Unix machine with
SNS-110 installed.
(2) Log-in with the SNS-110 IP address set up through the web browser. You must enter the exact ID and
password.
The initial user name and password are shown below.
● User Name : root
● Password : w2000
(3) After logged in, set up the additional network information in administration mode.
(4) Be sure to reset or switch off and then switch on your SNS-110 after setting.
Note
Please, refer to Chapter 5 and 7 for Log-in and administration mode network
setting up.
Changing IP Address
(1) To change the present IP address, log in with the present IP address. Then, change the IP address
in network set-up of administration mode.
Refer to Chapter 7. setting Administration Mode Network.
(2) Refer to APPENDIX B "Factory Default", to set up the factory default and set up a new IP address
according to Chapter 4, Setting an IP Address.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
In Cable Network through Cable Modem
(1) Connect according to
"Connecting to Cable Modem" of Chapter 3 Connecting to Network, and turn
the SNS-110 power on.
(2) SNS-110 automatically receives the following information from the cable network manager by
executing DHCP (Dynamic Host Configuration Protocol), if connected to cable network through a
cable modem.
● IP Address
● Gateway
● Subnet Mask
(3) Please confirm the auto-assigned IP Address from PC terminal emulation (HyperTerminal) connected to
RS-232C.
Please, refer to
"
Connecting to RS-232C
"
and APPENDIX C "How to Use Console".
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 SNS-110 Log-in
After successfully setting up an IP address as in Chapter 4, execute a web browser (Netscape or
Explorer) from an Internet PC.
Ideal Specification
If your PC performance is not compatible, the image processing speed will decrease in your web browser,
resulting in possible short-image.
Also, incompetent PC performance may cause PC abnormal function because of PC resource parts.
Therefore, use
● CPU: Pentium II more than.
● Main Memory: 64 MByte or more.
Because low web browser version also may cause problems in image processing, use
● Netscape 4.0 or higher version
● Explorer 4.0 or higher version
Note
There may be problems with video image transfer if Netscape 6.0 or above is
used, so use a version below 6.0
Log-in through Netscape
(1) Open Netscape web browser.
(2) Enter the SNS-110 IP address in Go to : xxx.xxx.xxx.xxx
34
Download from Www.Somanuals.com. All Manuals Search And Download.
(3) If you have properly logged in, you will see the following.
(4) Properly enter user name and password and click "OK" button. You should see the initial screen of
Chapter 6 Application Mode.
Log-in through Explorer
First Time
(1) If you have never logged in through Explorer, first download plug-in program from SNS-110.
Then, follow the next procedure.
(2) Open the Explorer web browser.
(3) Select "Tools" from top menu of the browser. And, select "Internet Options", then "Security".
Make sure the security level is set at "Medium" or lower. If not, please select "Confirm", after selecting
"Medium" or lower.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
(4) Enter the SNS-110 IP Address in Address : xxx.xxx.xxx.xxx
(5) If you have properly logged in, you will see the following.
(6) Properly enter user name and password and click
Then, you should see the security message.
"OK" icon.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
(7) Click
"Yes". You just have completed downloading Explorer plug-in program from SNS-110.
Then, you will see the initial screen of Chapter 6, Application Mode.
(8) If security level is set to
installed.
"High",then the following window appears and the program cannot be
Therefore, go back and set the security level to "Medium" or lower.
Warning
After the Explorer download completes, please place the security level in its
original position.
After the First Time
(1) Open Explorer web browser.
(2) Enter SNS-110 IP address in Address : xxx.xxx.xxx.xxx
(3) If you have properly accessed "Log-in" window appears.
(4) Properly enter user name and password and click "OK" button.
You should see the initial screen of Chapter 6 Application Mode.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
(1) The initial user name and password in factory defaults are as follows.
● User Name : root
● Password : w2000
(2) Log-in window appears only under the following condition.
● When "Password Enable" is set in the Web Transmitter setting of the Administration mode and you
have access to the Application mode, Log-in window appears.
The factory default is "Password Enable".
● When "Password Disable" is set in the Web Transmitter setting of the Administration mode and you
have access to the Administration mode, Log-In window appears.
The access to the Administration mode is restricted because it is used to change SNS-110
configuration.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6. Application Mode (Video Image Monitoring Mode)
Initial Screen
(1) If you have entered correct user name and password or clicked
next initial screen of application mode.
"Application" button, you will see the
(2) You will see the quadruplex screen with 4-video image input. And, without any image input, you will
see No Video
"
"
Single Screen
(1) By selecting an image from "Camera 1~4" button on left side of the screen, you will see individuals
image corresponding to your selection.
(2) Click the present image number to refresh.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Quadruplex Screen
(1) Click "Quad" button on left side of the screen.
You will see 4 individual screens in the quadruplex screen.
(2) Click any of the 4 screens to view it in single screen.
Automatic Sequential Screen
(1) Click "Sequential" button on left side of the screen in Application mode.
You will see 4 screen sequentially altering. The interval time between each screen can be regulated
in Administration mode.
(2) Screen configuration is set as in single screen condition.
Caution
The video quality in Quad/Sequential screen may be inferior, because the
transmitted video quality is set to be as in single screen.
If you view an image with Quad/Sequential screen in normal size, after setting
the single screen as Size Small/Video Quality High, the video quality is inferior
to when you view the single screen with Size Normal/Video Quality High.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Single Screen with PAN/TILT/ZOOM Controller
(1) After enabling PAN/TILT/ZOOM in Administration mode, if you select an image from "Camera 1~4"
button, you will see the next screen.
(2) Before operating PAN/TILT/ZOOM, the PAN/TILT/ZOOM controllers must have been connected, and
P/T/Z configuration must have been established in Administration mode.
(3) You will see scrolling bars around the image. You may select your preferred angle and position of the
image by clicking each bar. To move the camera to the presaved position, select the position in the box
on the left bottom of screen.
(4) To stop moving the image after clicking the control bar, click "▲" in the center of the bar to seize the
image.
Differences do exist depending on the types of PAN/TILT/ZOOM controller.
Sluggishness may occur in the image due to the time duration in network.
(5) If you click
4 images.
"Quad" button on left side of the screen in Application mode, you may simultaneously view all
(6) To transfer from Application mode to Administration mode, click
of the screen.
"Administration" on the left upper corner
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 Administration Mode
Initial Screen
(1) You must enter "root" for the user name and its password in the Log-in window to transfer to the
below Administration mode screen for both password-enable and password-disable condition.
(2) If the camera does not operate normally after accessing to the Administration mode, the camera icon
that is located on the screen blurs. If the camera operates normally, however, the icon shows in gray.
(3) You may set up PAN/TILT/ZOOM, Quad/Sequential, Web Transmitter, Alarm, and Network by
clicking each corresponding Icon.
If setting is not correctly done or many persons set at the same time in the
Note
Administration mode, this product may malfunction. So be careful to manage
the Log-in password in the Administration mode and it is recommended that
only the person who manages this product can use the product.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Camera Set-up
(1) You will see the following screen by clicking "Camera" icon in Administration mode.
(2) Camera Input
Automatically recognizes image broadcasting system (NTSC/PAL), Color/Black &white, or No Video.
If you click Refresh button at any time, this function will run through and set up new configuration of
image broadcasting system (NTSC/PAL), Color/Black &white, or No Video.
"
"
(3) Size
As the size of image in the screen, you may select
"
Small
",
"
Normal
", or "Large".
(4) Video Quality
Select one of
"Low",
"
Medium
", and "High".
(5) Text Display
In the purpose of displaying the title for each image, you may type the text in English or Korean.
If you click "Yes", the text is printed on the corresponding image.
Recommend
You can improve the transmitting speed, which is decreased by distal network
or traffic, by reducing the size or quality of image.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
(6) PAN/TILT/ZOOM
Select Disable
inactivated.
If Pan/Tilt/Zoom are properly connected, select
"
"
, if Pan/Tilt/Zoom controller is not connected. At this time "Preset" button is
"Enable".
(7) Preset
It will activate
"Preset" button. At this time, you will see the next screen, and you may remotely
control the position of camera.
After positioning the camera as your preference with Pan/Tilt/Zoom/Focus controllers, save this
position in
"
Current Position
". This saved position is to be selected in the future by clicking "Preset"
button in Application mode.
The coordinate of saved position is saved in Selection Box of Preset Position in Preset Page.
You can delete it by clicking "Remove" button, after selecting the name in Selection Box.
(8) Apply to
The initial coordinate only applies to particular camera input, such as
Camera 4
If you select
apply to the displayed texts.
"
Only Camera 1
"
~
"Only
".
"
All Cameras", the selected information applies to all 4 cameras. This function does not
44
Download from Www.Somanuals.com. All Manuals Search And Download.
PAN/TILT/ZOOM Set-up
(1) You will see the next window, if you click "P/T/Z" icon in administration mode.
(2) Device
To control PAN/TILT/ZOOM/FOCUS, connect the PAN/TILT/ZOOM/FOCUS camera & controller to the
+, - terminals of RS-485 on the rear of your web transmitter. For further information, refer to Chapter 3.
"Connecting to PAN/TILT/ZOOM/FOCUS Camera & Controller".
Here are the supported PAN/TILT/ZOOM/FOCUS camera & controller.
● Smart Dome Camera & Controller, made by Samsung Electronics
● P Protocol Dome Camera and Receiver, made by PELCO
● CPU Receiver, made by Sungjin Electronics
If you have a device other than Pan/Tilt/Zoom/Focus controller that is currently
Note
supported, contact your vendor.
(3) Baud Rate
Set up appropriate Baud Rate depending on the type of controller.
(4) Data Bit
Select Data Bit from either 7Bit or 8Bit, depending on the type of controller.
(5) Stop Bit
Select Stop Bit from either 1 Bit or 2 Bit, depending on the type of controller.
(6) Parity Bit
Select Parity Bit from Odd, Even, or None, depending on the type of controller.
(7) Camera Identity
Maximum of 4 PAN/TILT/ZOOM/FOCUS controllers may be connected. When connecting more than
one controller, you must assign an ID for each controller. Please, refer to the controller manual for its ID.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Quad/Sequential Set-up
(1) You will see the next screen by clicking Quad/Sequential icon in Administration mode.
(2) Quad Size
Select from either Small or Normal.
(3) Sequential Size
Select one from Small/Normal/Large.
(4) Sequential Interval
You may select the sequential interval from 3secs to 60secs. Your selected time will be the interval between
4 input images in the sequential screen.
(5) System
Select the image broadcasting system between NTSC and PAL, depending on where you are. SNS-110 is
designed to select automatically the image broadcasting system from the input image signal.
If you miscellaneously use different systems, such as NTSC and PAL, SNS-110 processes the image size
according to the system set-up in quad and sequential screen.
Recommend
You are recommended to use identical type of image signal, because video
quality may decrease or malfunction, if you use different type of signals in 4-video
input.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Web Transmitter Set-up
(1) You will see the next configuration window by clicking "Web Transmitter" in Administration mode.
(2) Date & Time
Select date and time.
(3) Security
①
New root pswd
Changes root password. New password must be more than 3 letters and less than 32, and must
include Arabian numbers.
Every time you log in to Administration mode, you have to enter user name and password, and
only valid password is "root" password.
②
User Name and Password
You may restrict the access from other users by registering user name. User name must be less
than 32 letters, and password must be more than 3 letters, and less than 32, and must include
numbers.
When you want to delete the registered user name, select the user name in
"Delete User" and
47
Download from Www.Somanuals.com. All Manuals Search And Download.
③
Pswd Enable
Restricts the access from other users. If you check the check box of "Pswd Enable" and click
"Apply" button, you should input registered username and its password in Log-in window to
access to the Application mode.
If you don’t check the check box of
"Pswd Enable", anyone is accessible to the Application mode.
Caution
Anyone, who is accessible to Administration mode, may change configuration
of SNS-110. If the configuration is deleted or altered, the system may be
damaged or malfunction. Therefore, factory default is set up with root
password.
After the initial installation, you are strongly recommended to change the root
password and restrict the access from other users.
(4) S/W Upgrade
Upgrade the currently installed program in SNS-110 to the most updated version.
①
Download the updated program version from Samsung Electronics web site .
program is sns110_vXXX_XXXX.bin.
②
③
Save the updated program version in the directory of SNS-110-connected PC.
Click
"Browse" and select the updated program, sns110_vXXX_XXXX.bin, in the directory.
The selected file will be saved in the browse window.
④
Click
"
Install
"
and open dialog window. You will see caution message, then click "OK" to start
program upgrade. Upon the upgrade completion, you will see another dialog window. You must
wait approximately for 2 minutes.
Caution
Wait until the "Upgrading is successful! New code will be loaded after
reset" message appears. Rebooting SNS-110 before this message can
cause fatal damage to the machine.
⑤
⑥
Reboot SNS-110 after the upgrade being completed as shown below.
● Press Reset button on the front panel.
"
"
● Turn off and then on SNS-110.
After successfully upgrade the program, execute web browser and Log-in.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Caution
Be careful not to install any other file except SNS-110 program
(sns110_vXXX_XXXX.bin) during S/W upgrade. You might accidentally trigger
the fatal system damage. Always reboot, after the system is upgraded.
After upgrading, Network setting (IP Address, DNS ) is not changed but the
user s input is initialized after rebooting and it has to be specified at
Administration Mode.
(5) Factory Default
If you click "factory default" button, all information or configuration of SNS-110 will return to the point of
purchase, except Ethernet address. Refer to APPENDIX B "Factory Default" for details.
Caution
Be careful when you execute “Factory Default”, because all configuration of
SNS-110 will return to the initial state, and it disables the Log-in.
(6) Software Reset
Reset the SNS-110 through Network.
Caution
The ‘Software Reset’ will disconnect all of the present connections of SNS-110.
Right after the S/W upgrade, ‘Software Reset’ doesn’t work.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the ALARM / RELAY Out
(1) Connect the alarm sensor to another device according to the ‘Chapter 3 Connecting to Instruments’.
The alarm level of the alarm terminal 1~4 is the following.
●Normal condition : TTL High Level (DC 5V)
●Alarm : TTL Low Level (DC 0V)
(2) If the alarm is set off the SNS-110 sends video images connected to alarm terminal 1~4, by E-mail or
to the FTP server on a set time gap. 5 frames for E-mail and 999 frames for FTP can be transferred,
and the E-mail with preset messages and video images can also be transferred.
(3) In the Administration Mode this settings window will be seen with a click on the "Alarm/Relay" icon.
(4) Status
The present status on the Relay Out terminal of the reverse side of the SNS-110. The toggle shaped
"Turn On/Off" button is used to control the external device connected to the Relay Out terminal.
(5) Sender
In order to send alarm messages and video images by E-mail, the E-mail address must be entered so
as to identify the sender. If the E-mail address is invalid the alarm messages and the video images
may not be sent as wanted.
Please, set the valid e-mail address of SNS-110 administrator at e-mail the ‘sender’.
Recommend
50
Download from Www.Somanuals.com. All Manuals Search And Download.
(6) Enable
Each alarm terminal has to be set as for whether the "Mail" or "FTP" transfer function is going to be
used. If the alarm sensor isn't installed or if the input signal can be ignored, click "No".
(7) Pre-alarm
If the video image transfer is set to FTP and the alarm went off, this will send the images that were
sent before the alarm. The number of the video images that is sent before the alarm is equal to the
'Image No.' in item (12), and if the Image No. surpasses 32, then a maximum of 32 frames will be
transferred.
(8) Receiver
This sets the E-mail address that will receive the alarm messages and the video images when the
alarm goes off. It is used when the 'Mail' is set in item (6).
(9) Subject
This sets the 'Subject' of the alarm message, and 30 characters can be entered. It is used when the
'Mail' is set in item (6).
(10) Message
This sets the alarm message it self, 30 characters can be entered. It is used when the 'Mail' is set in
item (6).
(11) Camera
This sets the image that will be transferred among Camera 1~ 4 when the alarm goes off.
(12) Image No.
This sets the page number of video images received. If the 'Mail' in item (6) is set, the mail No. is,
if the FPT is set the FTP No. is used. Mail can be used 1~ 5, and FTP 1~ 999.
(13) Time Delay
This sets the time gap while the still image is received. If is set for "2 seconds", it transfers one
captured cut of still image every 2 seconds and the figure set in item (12) is the number of repetition.
When set to "None", no time gap is used and the still image is captured and transmitted by the SNS-
110 with its highest ability.
Caution
If the attached file is blocked or the size is limited when sending an image file on the
SMTP server, the alarm messages and the video images may not be transferred.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Network Set-up
(1) You will see the next configuration window by clicking "Network" in Administration mode.
(2) IP Address
Enter SNS-110 IP Address. If the IP Address has been properly set up according to Chapter 4 Setting
up IP Address, the IP Address will automatically be set up and shown in the window.
If the IP Address is changed in use, re-set the IP Address on this menu. .
(3) HTTP Port
Set the Http Port to connect to a web browser. Default setting is at 80.
(4) DNS (Domain Name Server)
Set up the DNS server address assigned from the network manager and the address must be in
alphabet letters including numbers and "."
(5) Domain Name
Set up Domain Name address assigned by the network manager.
(6) Subnet Mask
Set up the Subnet Mask Address assigned by the network manager.
(7) SMTP (Simple Mail Transfer Protocol) Server
Set up the IP Address of mail server, where the message will be sent to when the alarm is raised.
The SMTP Server should support the e-mail address which is set at the
‘Sender’ of Alarm/Relay Out.
Caution
52
Download from Www.Somanuals.com. All Manuals Search And Download.
(8) Gateway
Set up the Gateway Address assigned by the network manager.
(9) DHCP (Dynamic Host Configuration Protocol)
DHCP is protocol, which automatically assigns IP address in network environment.
Those network environments automatically assigned with IP Address are as follows.
● Set DHCP "Yes" at Ethernet, which uses DHCP Sever.
● Also set DHCP "Yes" at Cable Network.
DHCP must be "NO" in the network environment besides the above two cases.
Click "Advanced" to notify the Dynamic IP address through mail or to register with
separate DB server. Refer to the "Appendix" for the further information.
Caution
If DHCP is set to "Yes" in the network environment, in which you manually
receive the IP address from the network manager, the Log-in condition may
be unsatisfactory during power on/off. Or, if DHCP is set to be "No" in the
network environment, which automatically assigns IP address to users, such
as Cable Network, the IP address may not be assigned to your terminal during
power on/off. When these do happen, please refer to FAQ section.
(10) Please, set up DHCP to appropriate network environment, when you want to change your network.
Then, turn the power off and connect to the network.
● Change DHCP "No" to "Yes" when you change Ethernet (manually assigned IP environment) to Cable
Network Ethernet (dynamically assigned IP Network environment).
● Change DHCP "Yes" to "No" when you change Cable Network, Ethernet (dynamically assigned IP
Network environment) to Ethernet (manually assigned IP environment).
Note
The basic form of internet address is xxx.xxx.xxx.xxx and xxx is a number
between 0~ 255.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
(11) FTP Server
Specifies the FTP Server address to send still image. The server address has to
be either network IP Address where SNS-110 can access or Host Name.
(12) FTP Port
Set the FTP Port to transfer still images to the FPT server. Default setting is at 21.
(13) User
Specifies the User ID to access FTP server.
(14) Password
Specifies the User Password to access FTP server.
(15) Directory
Specifies the server Directory to save the image sent through the FTP server.
Such characters like \ / * : ? " < > | cannot be entered.
Caution
To send image through the FTP server, specify a user who is authorized
to access the FTP server to create directories and upload files. The FTP
server has to be specified to create multi-level directories, if not, sending
images may not successfully work.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
File Transfer Setting
(1) Click "File Server" at Administration Mode to open the following window and to specify
the file transfer through the FTP server.
(2) Camera 1~4
Specifies the FTP transfer for input image from Camera 1 to Camera 4. Click "No" not
to use FTP transfer, click "Once" to transfer at one certain time a day, and click
"Every" to send in regular time gap for certain period of time. Click "Both" to use both
functions of "Once" and "Every."
(3) Once
Specifies the time to transfer image files. It only applies to the files which were set as
"Once" or "Both" at (2). Specify "Time"(0~23), "Minute"(0~59), or "Second"(0~59) to
transfer the image files through FTP server at set time. Each transferred files are
saved at respective cameras and Date Directories. For example, at Network Setting, if
you specify a directory as WebTxImage to save FTP server to send an image file at
Camera 1, at 10:12:15, the file is saved as the following file format.
~/WebTxImage/ch1/20001101/101215-once.jpg
~/WebTxImage/ch1/20001102/101215-once.jpg
....
(4) Every
Specifies the number of frame per hour to transfer image files. It only applies to files
which were set as "Every" or "Both" at (2). You can set desired number of frame or
time value or time unit, and set from 5 frames per second to 1 frame per 24 hours.
Click "No Delay" to transfer at the maximum speed.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
(5) Between
Specifies the starting and finishing time of image file transfer. It only applies to files
which were set as "Every" or "Both" at (2). You can set "Time"(0~23), "Minute"(0~59),
or "Second"(0~59). If starting and finishing time are identical, image files are
transferred all day.
(6) Day
Specifies days to transfer image files. It only applies to files which were set as "Every"
or "Both" at (2). You can choose the days for "Every" mode transfer. If "Everyday" is
checked, all the values under "Everyday" is ignored.
(7) Filename
Specifies file names. It only applies to file which were set as "Every" or "Both" at (2). If
you chose "Overwrite mode," files are overlapped to the specified names. If you
choose "Save mode," transferred files are being saved in each "Camera", "Date",
"Time" Directory. For example, at Network Setting, if you specify a directory as
WebTxImage to save FTP server to send an image file at Camera 1, at every 10
seconds, the file is saved as the following file format.
~/WebTxImage/ch1/20001101/10/105940.jpg
~/WebTxImage/ch1/20001101/10/105950.jpg
~/WebTxImage/ch1/20001101/11/111000.jpg
....
Click "Save" to transfer after specifying all the correct values.
If Alarm is raised while the image files by "Once" or "Every" mode are
being transferred through the FTP server, the transfer by "Once" or
"Every" mode is standby until the Alarm Image Transfer is done.
The image is continuously transferred after the Alarm Image Transfer is
completed.
Caution
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Custom User Interface Setup
(1) By clicking the "Web Browser" icon in the Administration Mode, the Custom User
Interface setting window appears. Start page, page title, background color, font color
and language can be set up, as the user wants.
(2) Start Page
The start page in the Application Mode allows a choice between one of Camera 1~4,
Quad, and Sequential.
(3) Page Title
Here the contents and the application of the Title String, which falls under the Page
Header of HTML, is set. The title that is typed in here is indicated on the title bar of the
Web Browser. If "No" is selected, the inputted characters are ignored and is set to
default.
(4) Background Color
The background color of the HTML is set and asks for application. The color constant
(i.e. Black, Red...) or the RGB (i.e. #9aabab) can be entered. If "No" is selected, the
inputted characters are ignored and is set to default.
(5) Text Color
The color of the characters on the screen is set and asks for application. The input
method is the same as done in item (4). If "No" I selected, the inputted characters are
ignored and is set to default. The color of the character with an icon image format
cannot be changed.
(6) Custom Logo URL
The address of the image file that will be used for the logo is set here. The full
address and file name has to be entered
If the indicated image file is unreadable, it will not be seen on the browser. Click
"No" to ignore the inputted characters and apply default settings.
(7) Language
English and Chinese can be used as the GUI language of the SNS-110.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
ABOUT/ SUPPORT/ HELP
(1)ABOUT
Provides you information on SNS-110.
(2)SUPPORT
Search for an webTX or SNS-110, and you can download SNS-110 user manual, a last update program
and troubleshooting instructions.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
(3 )HELP
Provides you with help messages on each function.
You can see help message as shown below by clicking
mode.
in the configuration window of Administration
?
Ex) the Help that appears when the
is clicked on the Camera setting window.
?
59
Download from Www.Somanuals.com. All Manuals Search And Download.
WEB
A
APPENDIX
SNS-110 SPECIFICATIONS
60
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX A SNS-110 SPECIFICATIONS
SPECIFICATIONS
Video In/Out
● Composite 4 Channel, Color & Black/White
● NTSC/PAL compatible
● BNC Type
● Loop Through Out
● 1.0 Vp-p, 75 Hi Z Termination type
Hardware
● 32Bit RISC CPU
● 2MByte Flash Memory
● 32MByte SDRAM
Operation System
● RTOS (Real Time OS)
Network Interface
● 10BaseT Ethernet
● 100BaseT Fast Ethernet
● Cable Modem
Image Compression
● Motion JPEG
Protocol
● TCP/IP, ARP, HTTP, FTP, SMTP, DHCP
Resolution
Mode
Size
NTSC
PAL
Single
Small
Normal
Large
176X120
352X240
704X480
176X136
352X272
704X544
Quad
Small
Normal
176X120X4
352X240X4
176X136X4
352X272X4
Sequential
Small
Normal
Large
176X120
352X240
704X480
176X136
352X272
704X544
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Performance
● Max 30 Frame/Sec (1 User Single Mode Connection)
Alarm In
● Input 4 Port
● TTL Level "Low" Active
● Sends the Video screen through E-mail/FTP in case when alarm sets off
● Pre-Alarm
Relay Out
● Output 1Port
● Regular Capacity of Relay
- 2A 30VDC
- 0.5A 125VAC
Serial Connector
● RS-232C 1 Port (9 Pin D-Sub): Console
● RS-485 1 Port (Terminal Block): PAN/TILT/ZOOM Control
Installation & Software Upgrade
● IP Configuration : ARP, DHCP Protocol, Using RS-232C Cable
● Software Upgrade : RFC 1867
Web Browser
● Netscape 4.0 or more (Currently we have problems with supporting Netscape 6.0 or more)
● Explorer 4.0 or more
Security
● Password Protection
Deviation of programmed clock
± 30 Sec/Month or less
Environment
● Operating Temperature: 0oC ~ 40oC
● Storing Temperature: -20oC ~ 60oC
● Operating Humidity: 20% ~ 85% RH
● Storing Humidity: 20% ~ 95% RH
Power
● Input Rating: AC110 ~ 240V, 50 ~ 60Hz, 0.5A
● Output Rating: DC+5V, 3A
● Power Consumption: 12 Watts
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulation Approval
Note: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interface in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
- Reorient of relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or an experienced radio TV technician for help.
Outside view
+
+
-
R C R A G
G
2
1
3
4
-
T X
R X R / O
A L R A M
A L A R M I N
1.CONTROL 2.F/H 3.Tx
R
4.Rx
R
63
Download from Www.Somanuals.com. All Manuals Search And Download.
WEB
B
APPENDIX
Factory Default
64
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX B Factory Default
Factory Default sets the program back to the condition at the time of purchase.
Please note that after Factory Default has been enabled, network information is also deleted, so establishing
a connection is impossible. Refer to Chapter 4, Setting an IP Address, in order to set a new IP address.
How to Enter the Factory Default
(1) Power on the SNS-110 or push the ‘Reset’ button in front of the SNS-110 while pushing the ‘PRESET’
button. Then the Power LED of SNS-110 turns on and off just one time. The turn state of Power LED
says that the progress of Factory Default is going on. Hole on pushing the ‘Reset’ button.
(2) When the progress of Factory Default cornplete, the Power LED turns on again.
Stop pushing ‘Reset’ button.
(3) All the setting of SNS-110 returns as the state of purchase.
Values for setting up SNS-110
Items
Factory Default Value
Camera 1~4
Camera Input
Size
Blank
Normal
Low
Video Quality
Text Display
PAN/TILT/ZOOM
Apply to
Blank/No
Disable
Only Cemera 1~4
P/T/Z
Device
None
Baud Rate
2400
Data Bit
8
Stop Bit
1
Parity Bit
None
Camera 1 ldentity
Camera 2 ldentity
Camera 3 ldentity
Camera 4 ldentity
Quad Size
0
1
2
3
Quad/
Normal
Sequential
Sequential Size
Sequential Interal
System
Normal
3
NTSC
Web
Date & Time
Security
2001/January/1 00:00:00
Administration ID:root/Password:w2000
User ID: guest 1/Password:guest1
Password Enable
Transmitter
Software Upgrade
Blank
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Items
Alarm /
Relay Out
Factory Default Value
Relay Out Status
Sender
Off
Blank
No
Enable
Receiver
Subject
Blank
Blank
Blank
Message
Camera
Camera 1,2,3,4
Image No.
Time Delay
IP Address
HTTP Port
DNS
Mail : 1/ FTP: 10
None
Network
0.0.0.0
80
0.0.0.0
Domain Name
Subnet Mask
SMTP Server
Gateway
DHCP
Blank
0.0.0.0
Blank
0.0.0.0
Yes
FTP Server
FTP Port
User
0.0.0.0
21
Blank
Password
Directory
Blank
Blank
File Server Camera1
Camera2
Camera3
Camera4
Once
No
No
No
No
0:0:0
Every
1frames/1Minute
Between
Day
0:0:0 and 0:0:0
Everyday
Filename
cam
Web
Start Page
Quad
Browser
Page Title
Web Transmitter-Samsung Electronics/(No)
Background Color
Text Color
#b8b8b8/(No)
Black/(No)
logo.gif/(No)
English
Custom Logo URL
Language
Warning
All network-related information but Ethernet Address will be deleted.
Therefore, you must be extremely careful when you execute this function.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
WEB
C
APPENDIX
How to Use Console
67
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX C How to Use Console
Console allows condition check-up of SNS-110 by connecting to RS-232C port, manually setting network-
related information.
Starting Console
(1) Connect to RS-232C port on the PC in accordance with
Connecting other equipments”
"
Connecting to RS-232C
"
of "Chapter 3,
(2) Use Terminal Emulation (Hyper Terminal) from the connected PC to set the values for RS-232C
through Terminal Emulation.
(3) The following message will appear when you turn on the power of SNS -110.
Message
(1) When the power is turned on, the following message will appear on the console screen when
SNS-110 has been successfully installed.
########################################################
#
#
#
#
#
#
#
#
#
#
SAMSUNG Electronics. Co., Ltd.
webTX(Internet Video Server):SNS-110
Version1.1(2000~2001) All Rights Reserved.
########################################################
>Current status is Flash Memory Boot
>To change system parameter, press any key within 2 seconds
....IP:168.219.13.11
☞ If any key is pressed within two
seconds, manual setup mode
will appear.
3, SM:255.255.255.192, GW:168.219.13.65
>Web Transmitter Image Loading<
>Ethernet(MAC) address in Cookie : [00-00-f0-ff-a1-ba]
>Network parameters in gstrIP, gstrSubnetMask, gstrGtwyIP
-IP:168.219.13.113 SM:255.255.255.192 GW:168.219.13.65
>Network Interface Installed
☞ Indicates Ethernet address
☞ Indicates IP address, Subnet
Mask, and Gateway
>DNS IP address is empty or invalid
************************* HttpPort = [80]
************************* FTP port = [21]
Initializing External Devices... (f_InitExtDev())
EXTACON0 = 06110a59, EXTACON1 = 00000000
Timing COS/ACS/COH/ACC : 1315 1203 0000 0000
init universal timer(#1), 1ms period
system has 4 decoder(s).
all decoders/channels are reset.
rtc init step skipped.
Rtc time : 2001/1/1 [Mon] 04:06:17
☞ Indicates the time elapsed with
SNS-110
reflected os time : 2001/01/01 04:06:17
JpegRESET: write reg 0 <- 0 fail. a0 read
Jpeg reset ok.. loading..
Jpeg header size : 591 (0x24f) bytes
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Codec initialized, register updated.
Create/Start working tasks... (f_CompVideo())
JCPY task start (id=1638400)
AlarmCheck task start (id=1703936)
Mailing task start (id=1769472)
PTZ control task start (id=1835008)
Create FTPClientTask.. Enter the loop.
Create PreAlarmTask.
All Task started.
Wait until jpeg task ready...
Launch Webcontrol server as new thread.
WebServer task created. now starting..
>Relay Status : 0
wt_cookie initialized.
SetCrsz 0x1111 : 01 01 01 01
using Cam Size/CR Info from FLASH 0x1111
WT_PSWD : cookie->user_count=2
WT_PSWD_AddEntry: NEW <uid=root, pswd='w2000', mem=0x76063c>
WT_PSWD_AddEntry: NEW <uid=guest1, pswd='guest1', mem=0x76053c>
WT_PTZ: PTZ driver [0x4e] 'None'
dummy ptz dirver inited.
user cmd: 'ptz' registered.
ftp server addr invalid.
End of WT_FTP_INIT
All modules initialized.
****************************************************************
*
Internet Video Server : webTX SNS-110
*
*
*
*
* -System Version sns110.1.1 (Build 01.10.16.13.55)
* -WebServer Version 3.1
☞ Indicates the software version
loaded on SNS-110
* -OCX Version 1.0.1.6
****************************************************************
MAIL: Mailing Loop enter..
Alarm-port checking Task started.
Alarm check period : 100 ms, current alarm IO: 0x000080e0
ftp server addr invalid.
End of WT_FTP_INIT
PTZ control task started.
>Log In :
(2) When you correctly enter user name "root" and password, the following message will appear.
>Log In : root
>Password :
>Welcome to SAMSUNG webTX SNS-110
SNS-110>
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Command
(1) help: Indicates Command items
SNS-110> help
telnet
ping help status tftpdn reset freset jpgtest
SNS-110>
(2) ping: Indicates the connection status to a given IP Address
SNS-110> ping 168.219.13.115
ping (168.219.13.115): 56 data bytes
168.219.13.115 is alive
SNS-110>
(3) status: Indicates the current condition and information of SNS-110
SNS-110> status
size of data = 2144
SNS-110 System Parameter List
Version sns110.1.1 build 01.10.16.13.55
********** Board Parameters **********
Compiled option : Codec external bank, FIFO external bank I/O
********** Cookie Parameters **********
Active cookie 0x51e0000 (37), stamp 78
Backup cookie 0x51f0000 (38), stamp 77
cookie base : 0x051e0000, cookie size : 3896
--System
version of system : sns110.1.1, webserver : 3.1, ocx : 1.0.1.6
buildtime : detected 01.10.16.13.55, cookie report 110.1.0.170
--Network parameter
Mac : <00-00-f0-ff-a1-ba>, IP : <168.219.13.113>
Netmask : <255.255.255.192>, gateway : <168.219.13.65>
SMTP : <>, DNS : <>
HTTP port : 80
tftp server : <> / <rom.bin>
DHCP : off, BOOTP : off, RARP : on
70
Download from Www.Somanuals.com. All Manuals Search And Download.
--User information
number of user : 2
user list
0 <root:w2000:10>
1 <guest1:guest1:1>
--Camera setting
Cam1 : size 1, CR 0, title off, <>
Cam2 : size 1, CR 0, title off, <>
Cam3 : size 1, CR 0, title off, <>
Cam4 : size 1, CR 0, title off, <>
Quad size 1, Quad mode 0, Seq size 1, Seq interval 1
Cam ptz control 0 0 0 0
User password enabled (1)
--Alarm parameter
alarm1 no, rcv addr , sender addr , camera 1, 0/10 images, interval 0
subject <>, message <>
alarm2 no, rcv addr , sender addr , camera 2, 0/10 images, interval 0
subject <>, message <>
alarm3 no, rcv addr , sender addr , camera 3, 0/10 images, interval 0
subject <>, message <>
alarm4 no, rcv addr , sender addr , camera 4, 0/10 images, interval 0
subject <>, message <>
--P/T/Z parameter
driver : <None>
serial : 2400 bps, data 8, stop 1, parity 0
ptz address 0 1 2 3
ptz preset setting list
(0) id0, name <None>
total 0 menu.
--FTP parameter
server:<> user:<> pass:<>
dir:<>
FTP port : 21
enable 0 0 0 0 once 0:0:0
every 1 min, betw 00:00:00~00:00:00, day 1
--Dynamic IP
reg enabled, server:<> cgi:</cgi-bin/webtx.cgi?regist=%e&host=%i>
mail enabled, addr:<[email protected]>
--User Interface
title disabled, <WebTransmitter - Samsung electronics>
bgcolor disabled, <#b8b8b8>
txtcolor disabled, <black>
logo disabled, <logo.gif>
********** DHCP network parameters **********
system boot with fixed IP saved in NVRam
----
SNS-110>
71
Download from Www.Somanuals.com. All Manuals Search And Download.
(4) tftpdn : Using the ftp Server, software can be downloaded as the following.
First the tftpdn Server has to be running on the PC with the new software.
The tftp Server isn't offered separately. Users must use their own tftp server programs.
SNS-110> tftpdn
****************************************************************
*
Main Image Download & Flash Update by TFTP
*
****************************************************************
>TFTP Server(Default:0.0.0.0) : 168.219.13.101
>TFTP Server : 168.219.13.101(0xa8db0d65)
>Download File(Default:rom.bin) and 'q' to exit) : rom.bin
>Download File : rom.bin
☞ Enter the IP address of the tftp
Server
☞ Enter the filename of the
software that will be
downloaded from the tftp Server
>Main Image Download & Buffering
BBBBBBBBBBBBBBBBBBBBBBBBBBBBB
>Transfered 956560(0xe9890)Bytes
☞ The software is being
downloaded from the tftp
Server
>Unlock Flash Block
UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU
>Erase Flash Block(B0~B21 0xe9890Bytes)
EEEEEEEEEEEEEEEEEEEEEE
>Write Flash Block(0xe9890Bytes)
☞ The downloaded software is
being written on the Flash
Memory
PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPP
>Lock Flash Block
LLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLL
>Cookie Validate [168.219.13.113] [00-00-f0-ff-a1-ba] [255.255.255.192]
>Main Image Download & Flash Update Complete
SNS-110>
(5)reset: SNS-110 »Reset ‰ˆ¯·ˇ· .
SNS-110> reset
reset after 0 second.
SNS-110> Reset requested!!! reset after 1 ms
>Application shutdown
###############################################################
#
#
#
#
#
#
#
#
#
#
SAMSUNG Electronics. Co., Ltd.
webTX(Internet Video Server):SNS-110
Version1.1(2000~2001) All Rights Reserved.
###############################################################
>Current status is Flash Memory Boot
>To change system parameter, press any key within 2 seconds ....
72
Download from Www.Somanuals.com. All Manuals Search And Download.
(6) freset : the SNS-110 settings are initiated for factory shipment
SNS-110> freset
Setting HTTP port to 80 and FTP port to 21.
>Application cookie field initialized.
Cookie App field initialized.
ftp server addr invalid.
For complete erase, use PRESET button.
End of WT_FTP_INIT
SNS-110>
Manual Configuration Mode
(1) Once you turn the power on and SNS-110 functions normally, the following message will appear,
and if you press any key, you will be able to set the values manually.
########################################################
#
#
#
#
#
#
#
#
#
#
SAMSUNG Electronics. Co., Ltd.
webTX(Internet Video Server):SNS-110
Version1.1(2000~2001) All Rights Reserved.
########################################################
>Current status is Flash Memory Boot
☞
Press any key at this stage.
>To change system parameter, press any key within 2 seconds ...
The following message appears if you do not press Space Bar or Enter. This is to wait for the reception of
the IP Address, which is transmitted through network.
########################################################
#
#
#
#
#
#
#
#
#
#
SAMSUNG Electronics. Co., Ltd.
webTX(Internet Video Server):SNS-110
Version1.1(2000~2001) All Rights Reserved.
########################################################
>Current status is Flash Memory Boot
>To change system parameter, press any key within 2 seconds
....IP:0.0.0.0, SM:0
.0.0.0, GW:0.0.0.0
>Web Transmitter Image Loading<
73
Download from Www.Somanuals.com. All Manuals Search And Download.
>Ethernet(MAC) address in Cookie : [00-00-f0-ff-a1-ba]
>Forced to use DHCP for IP address setting(DHCP Flag=0x1)
>Stored IP address <00000000> is not valid!
>RARP(Fixed IP) Mode -> Try to find IP : Retry No.[1]
>Ethernet(MAC) address in RARP mode : [00-00-f0-ff-a1-ba]
.....
>DHCP(Dynamic IP) Mode -> Try to find IP : Retry No.[1]
.....
>RARP(Fixed IP) Mode -> Try to find IP : Retry No.[2]
>Ethernet(MAC) address in RARP mode : [00-00-f0-ff-a1-ba]
.....
>DHCP(Dynamic IP) Mode -> Try to find IP : Retry No.[2]
.....
To go to the next level, go over to the number (1) after re-running SNS-110. When you successfully
entered Space Bar or Enter, the following screen appears.
(2) When the following message appears by running the above item, you can manually set the
information relating to Network.
--------------------------------------------
[WEB Transmitter(SNS-110) Version 1.1]
Boot command Loop menu
--------------------------------------------
[p] Print Boot Parameters
[c] Change Boot Parameters
[q] Quit Menu
-------------------------------------------
Select items? [ ]
(3) If you enter "p" at "Select items?", you can access the network information.
Select items? [ ] p
----------- SNS-110 Parameters-------------
ip address: 0.0.0.0
Ethernet address: [00-00-f0-ff-a1-ba] (41402)
Subnet mask address: 0.0.0.0
SMTP Mail server: NULL
DNS Server address: 0.0.0.0
Gateway address: 0.0.0.0
Domain Name: NULL
74
Download from Www.Somanuals.com. All Manuals Search And Download.
tftp server address: 0.0.0.0
tftp boot file:[rom.bin]
DHCP Enabled:[1]
IP auto-reg server:[NULL]
IP auto-reg cgi:[/cgi-bin/webtx.cgi?regist=%e&host=%i]
IP auto-reg enable:[1]
IP notify-mail address:[[email protected]]
IP notify-mail enable:[1]
--------------------------------------------
[WEB Transmitter(SNS-110) Version 1.1]
Boot command Loop menu
--------------------------------------------
[p] Print Boot Parameters
[c] Change Boot Parameters
[q] Quit Menu
-------------------------------------------
Select items? [ ]
(4) If you enter "c" when "Select items?" appears, you will be provided with the menu, which will allow you
to manually set the network information.
Select items? [ ] c
[ WEB Transmitter ( SNS-110 ) Version 1.1 ]
Boot parameters modification menu
--------------------------------------------
[i]. Ip address modify
[s]. Subnet mask address modify
[m]. SMTP mail server address modify
[d]. DNS server address modify
[g]. Gateway address modify
[n]. Domain name modify
[1]. IP auto-regist server address
[2]. IP auto-regist cgi format
[3]. IP auto-regist enable/disable
[4]. IP notify-mail enable/disable
[5]. IP notify-mail address
[c]. dhcp flag modify
[q]. Quit menu
--------------------------------------------
Select items? [ ]
75
Download from Www.Somanuals.com. All Manuals Search And Download.
(5) If there is information you would like to change or update, you can do so at this time.
Select items? [ ] i
LAN IP address? [0.0.0.0] 168.219.13.113
168.219.13.113
Turning off DHCP mode....
Warning
To use the Static IP Address, put "0" for DHCP flag and to use the Dynamic IP
Address, put "1." The default is "1" but when you change IP Address, DHCP flag is
automatically changed to "0." Confirm for more accurate setup.
(6) If you enter "q" when "Select items?" appears, you will go back to menu of (2).
(7) If you enter "q" when " Select items?" appears, SNS-110 will boot, and Network will be set to the
values you have assigned.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
WEB
D
APPENDIX
Dynamic IP Information
Transfer
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D Dynamic IP Information Transfer
In such an environment where you have to be assigned with Dynamic IP as Cable Modem,
you need separate method since users cannot know IP information. SNS-110 uses two
methods to show the Dynamic IP information to users. One is to send IP information to the
administrator’s email, and the other is to send the Dynamic IP information to the
Administration server.
●
For this function to properly work, SMTP, DNS, or Gateway have to be all properly set.
When you cannot access through the browser, refer to the Appendix C and set at the
console.
To send IP information to the administrator E-mail
When you are assigned with Dynamic IP through DHCP, you can send the assigned IP
Address through email. When you cannot access through the browser at the first setting,
use the following method to use the console.
Run the Boot Command Mode as explained in Appendix C, "Manual Configuration Mode"
and choose "Change Boot Parameters" menu.
--------------------------------------------
[WEB Transmitter(SNS-110) Version 1.1]
Boot command Loop menu
--------------------------------------------
[p] Print Boot Parameters
[c] Change Boot Parameters
[q] Quit Menu
-------------------------------------------
Select items? [ ] c
[ WEB Transmitter ( SNS-110 ) Version 1.1 ]
Boot parameters modification menu
--------------------------------------------
[i]. Ip address modify
[s]. Subnet mask address modify
[m]. SMTP mail server address modify
[d]. DNS server address modify
[g]. Gateway address modify
[n]. Domain name modify
[1]. IP auto-regist server address
[2]. IP auto-regist cgi format
[3]. IP auto-regist enable/disable
[4]. IP notify-mail enable/disable
[5]. IP notify-mail address
[c]. dhcp flag modify
[q]. Quit menu
--------------------------------------------
Select items? [ ]
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Enter "5" and go to IP notify-mail address to type E-mail address you want.
Select items? [ ] 5
Enter "4" and go to IP notify-mail enable/disable and enable it.
Select items? [ ] 4
IP notify-mail enable? [Y]
Select Quit menu to exit Boot Command Mode.
When all the network settings are properly installed and DHCP function is enabled, Dynamic
IP information is sent to the email, which was set while SNS-110 was booting. The following
is what happens when the email is sent
From: WebTransmitter
Subject: IP Notification (168.219.44.137)
New IP 168.219.44.137 is obtained by DHCP. 00-00-f0-ff-a1-ff
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Registering IP information with Administration server
Install HTTP server, which can process the Properties transmitted by SNS-110, or
receive separate service from the Service Provider to register IP information with
Administration server. Dynamically assigned IP information can only be set at SNS-110,
whether which name or server will be used. If you cannot access the browser, use the
console to set up.
Run the Boot Command Mode as explained in Appendix C, "Manual Configuration
Mode," and select "Change boot parameters" menu.
##########################################################
#
#
#
#
#
#
#
#
#
#
SAMSUNG Electronics. Co., Ltd.
webTX(Internet Video Server):SNS-110
Version1.1(2000~2001) All Rights Reserved.
##########################################################
>Current status is Flash Memory Boot
>To change system parameter, press any key within 2 seconds ..
--------------------------------------------
[WEB Transmitter(SNS-110) Version 1.1]
Boot command Loop menu
--------------------------------------------
[p] Print Boot Parameters
[c] Change Boot Parameters
[q] Quit Menu
-------------------------------------------
Select items? [ ] c
[ WEB Transmitter ( SNS-110 ) Version 1.1 ]
Boot parameters modification menu
--------------------------------------------
[i]. Ip address modify
[s]. Subnet mask address modify
[m]. SMTP mail server address modify
[d]. DNS server address modify
[g]. Gateway address modify
[n]. Domain name modify
[1]. IP auto-regist server address
[2]. IP auto-regist cgi format
[3]. IP auto-regist enable/disable
[4]. IP notify-mail enable/disable
[5]. IP notify-mail address
[c]. dhcp flag modify
[q]. Quit menu
--------------------------------------------
Select items? [ ]
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Type "1" and go to IP auto-regist server address" to type registered Web Server address.
The example below is the IP Address such as 168.219.44,137 or registered host name
[ WEB Transmitter ( SNS-110 ) Version 1.1 ]
Boot parameters modification menu
--------------------------------------------
[i]. Ip address modify
.
.
.
.
[q]. Quit menu
--------------------------------------------
Select items? [ ] 1
IP auto-regist server? 168.219.44.147
Type "2" and go to IP auto-regist cgi format to type the cgi program path to transmit or
the name of name of the program path, or the transfer factor.
[ WEB Transmitter ( SNS-110 ) Version 1.1 ]
Boot parameters modification menu
--------------------------------------------
[i]. Ip address modify
.
.
.
.
[q]. Quit menu
--------------------------------------------
Select items? [ ] 2
IP auto-regist cgi? [/cgi-bin/webtx.cgi?regist=%e&host=%i] /cgi-bin/webtx.cgi?regist=%f&host=%i
Cgi format to type here are as follows.
[CGI path] : It is the path of the directory which CGI program is located and it
has to start with the root symbol (/).
The example above is /cgi-bin/.
[CGI program] : It is one of the names of CGI program which server provides.
The example above is webtx.cgi.
[Format string] : It is the value that is transmitted as factor to the CGI program.
If you use the following values starting with %, you can send
the SNS-110 network information.
%e : The last three digits of Ethernet address (Hex form)
Example: ffa142
%f : The six digits of Ethernet address (Hex form)
Example: 0000f0ffa142
81
Download from Www.Somanuals.com. All Manuals Search And Download.
%g : Ethernet address (standard) Example: 00-00-f0-ff-a1-42
%i : IP Address (dotted decimal) Example: 168-219-44-137
%u : IP Address (32bit unsigned integer, hex form)
Example: a8db2c89
%% : Means %
Select Quit Menu to exit Boot Command Mode.
[ WEB Transmitter ( SNS-110 ) Version 1.1 ]
Boot parameters modification menu
--------------------------------------------
[i]. Ip address modify
.
.
.
.
[q]. Quit menu
--------------------------------------------
Select items? [ ] q
--------------------------------------------
[ WEB Transmitter ( SNS-110 ) Version 1.1 ]
Boot command Loop menu
--------------------------------------------
[p]. Print boot parameters
[c]. Change boot parameters
[q]. Quit menu
-------------------------------------------
Select items? [ ] q
New Boot parameter updated.
.
.
.
If you entered as the example above, the URL that is transmitted to the SNS-110-set
Administration Server (IP auto-regist server) as follows.
This means to transmit factors like regist=0000f0ffa142 and host=168.219.44.137 to cgi-
bin/webtx.cgi of the Administration server which has 168.219.44.147 address. Samsung
Electronics only provides methods for Ethernet Address and IP aAddress, which transmit
to the Administration server. Administration Server have to save and manage the
information (Ethernet Address and IP Address) which it received. Users must deploy
saving and managing program for this and Samsung Electronics can provide help for
that.
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting with the Web Browser
When you have SNS-110 address and can access through the Web Browser, you can
change the setting as above at the Administrator Mode.
When you run the Network Setting window as explained in the Chapter 7 and click
"Advanced" for DHCP, the Dynamic IP setting window appears as below.
You can change or add the values set at the Console.
CGI Program for the Administration Server
examples for setting up the Administration server.
83
Download from Www.Somanuals.com. All Manuals Search And Download.
WEB
E
APPENDIX
FAQ
84
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX E FAQ
As you continue to use SNS-110, there could be some cases, which we have not yet discussed in this
manual. In such a case, it might actually be when SNS-110 has an error. But in most cases, an easy do-it-
right can fix the difficulties. Please react to the symptoms by following the instructions below.
When you get no Message after connected SNS-110 and PC with
RS-232C Cable and executed Terminal Emulation Program
(e.g. hyper terminal).
(1) Refer to "Connecting to RS-232C" of chapter 3, and check the connection condition of RS-232C cable.
(2) Check whether there is no conflict at the connected PC's COM Port.
(3) Check if the Terminal Emulation (Hyper Terminal) is running to the PC that you want the connection
established.
(4) Check if the settings are correct as is mentioned in "Connecting to RS-232C".
When inner connections are established but outer ones are not.
(1) Check if the external user has a proper connection to the Network.
You can check this by executing "Ping" to the user's IP address at DOS window.
(2) Access a PC through internal connection, and check if the values are normally set for IP address,
Gateway, and Subnet Mask of network setup in Administration mode.
When e-mails are not sent and alarm sets off
(1) Check and see if the alarm sensor is properly connected to SNS 110, and functions normally.
(2) Refer to "Connecting to Alarm Sensor", Chapter 3.
(3) Check the connected values of Alarm/Relay Out setting at Administration mode.
Take special note for receiver's e-mail address.
(4) Check the values assigned for Domain Name, SMTP server setting at Administration mode.
Ex) Domain Name: samsung.co.kr
SMTP Server : vcr.sec.samsung.co.kr or 168.219.13.12
(5) Make sure the E-mail address entered on the 'sender' of the Alarm/Relay Out in the Administration Mode
is valid.
When there is no response by executing "Ping" in the process of
setting the IP address
(1) Check the condition of the network you wish to connect SNS-110 to. Once Network is established,
LED of SNS-110's Network should be blinking. If it isn't, please contact the network manager.
85
Download from Www.Somanuals.com. All Manuals Search And Download.
(2) If LED of Network for SNS-110 is working correctly, the values for Network within SNS-110 might have
been incorrectly entered. In such a case, refer to Supplement B Factory Default to turn the settings to
the factory mode. Then, retry setting the IP address again, as shown in Chapter 4.
The PC to setup the IP Address at SNS-110 must use the IP Address that has the same network as the
IP Address to setup at SNS-110.
For example, the IP Address you want to be authorized with SNS-110 is 168.219.15.212, the PC that is
used for setting up IP Address through arp, ping should be 168.219.15.XX. That means it should have
the same network class (168.219.15).
In case the same Network Addresses cannot be authorized, use Hyper Terminal to setup IP Address.
When connections to SNS-110 cannot be established, after
connected to Cable Network
(1) See if the cable modem between cable network and SNS-110 is working correctly.
Contact the cable modem supplier.
(2) If it works on Ethernet but does not under cable network mode, re-set the value of network in
Administration mode to "YES" and disconnect it from Ethernet and install cable network.
If you try to connect cable network to Ethernet with the value "NO", you cannot obtain an IP address, so
you will not be able to establish a connection. In such a case, RS-232C's Terminal Emulation (Hyper
Terminal) should be used in re-setting the value. Refer to Supplement C, How to Use Console.
(3) If none of the above works, refer to Supplement B to set the values back to the factory mode and install
Cable Network.
If you wish to check the IP Address under auto-set IP address
environment
(1) Under the network condition of DHCP server using Cable Network or Ethernet, install SNS 110 and turn
the SNS-110 power on, then you will be given with an IP address from DHCP Server. This will auto-set
the information for SNS-110's network information.
(2) Set the SNS-110 and peripheral PC's RS-232C cable to SNS-110's IP address, then refer to
Supplement C How to Use Console to check the network information.
(3) Note that a new IP addresses will be given every time you turn the power on for SNS-110 under auto-set
IP Address.
(4) If you wish to receive a fixed IP address under the auto-set IP address environment through Ethernet,
you may contact the manager and have an IP address fixed to your connection by registering your IP
address and Ethernet address.
(5) When you connected SNS-110 with Cable Modem, it’s easy to manage the assigned IP Address if you
use the method using Administration server explained earlier.
86
Download from Www.Somanuals.com. All Manuals Search And Download.
When the post-version software still operates, even after you have
installed the updated version.
(1) When you upgrade to the latest version of the software, the "Uploading is successful! New code will
be loaded after reset" message appears. When this message appears, reset or restart SNS-110 and
the new software will reboot the system.
(2)To check the version, press "about" in "Administrator Mode" in SNS-110.
When normally-functioning SNS-110 is suddenly not
connecting
(1) Check if the LED light is blinking on the front of SNS-110.
(2) If it isn't, contact the network manager to check the status of network. If no fault is identified from the
network, refer to Supplement B, Factory Default, and set the information back to its original status,
and Use chapter 4 to set an IP address.
(3) If the system does not work even after a new IP Address has been selected, contact your local
service center.
When SNS-110 does not work after downloading to upgrade to the
latest version of the S/W of SNS-110
(1) If you upgraded SNS-110 by using a separate file other than one was supplied by Samsung
Electronics, it becomes non-functional.
(2) If your SNS-110 doesn't function at all, even though the software normally supplied by Samsung
Electronics was used for upgrading., then contact your vendor or Service Center.
87
Download from Www.Somanuals.com. All Manuals Search And Download.
If the Video image has problems when connected to SNS-110 using
a Netscape
(1) This can happen if Netscape 6.0 or above is used.
(2) Use Netscape 5.X or below.
(3) The defects related to Netscape 6.0 are being fixed.
You cannot use FTP for transfer when setting up FTP transfer
(1) Check [Start] – [Settings] to see if current time is set for SNS-110. If the current time is not properly
set, FTP transfer does not work.
(2) Check "File Transfer setting menu" to see if each camera setting is set "Both" or "Once." or "Every" .
(If it is set "none," it doesn’t work.)
(3) Check "Every" item in "File Transfer Setting menu" to see if proper values are set.
(4) Check "Between" item in "File Transfer Setting menu" to see if proper values are set. "All day mode"
can be set as "0:0:0 ~ 0:0:0."
(5) Check "Day" item in "File Transfer Setting menu" to see if proper values are set. Click "Every day" for
"Every day mode."
(6) Check "Network Setting Menu" to see if FTP Srerver "IP Address" , "FTP Port" and "User" ,
"Password" , "Directory" is properly set.
(7) Check “FTP Server” is properly set.
(8) Check “FTP Server” connected to “user” is properly set.
If none of the above helps for troubleshooting, please contact the dealer, or
contact SNS-110's service center, in which you will receive professional
assistance.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRONICS
AB68-00278A
Download from Www.Somanuals.com. All Manuals Search And Download.
|